Network Topologies: Bus Topology

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 3

Network Topologies

 The way in which devices are interconnected to form a network is called network
topology.
 Some of the factors that affect choice of topology for a network are −
Cost − Installation cost is a very important factor in overall cost of setting up an
Infrastructure. So cable lengths, distance between nodes, location of servers, etc.
have to be considered when designing a network.
Flexibility − Topology of a network should be flexible enough to allow
reconfiguration of office set up, addition of new nodes and relocation of existing
nodes.
Reliability − Network should be designed in such a way that it has minimum down
time. Failure of one node or a segment of cabling should not render the whole
network useless.
Scalability − Network topology should be scalable, i.e. it can accommodate load of
new devices and nodes without perceptible drop in performance.
Ease of installation − Network should be easy to install in terms of hardware,
software and technical personnel requirements.
Ease of maintenance − Troubleshooting and maintenance of network should be
easy.

Bus Topology
 Data network with bus topology has a linear transmission cable, usually coaxial, to
which many network devices and workstations are attached along the length.
 Server is at one end of the bus.
 When a workstation has to send data, it transmits packets with destination address in
its header along the bus.
 The data travels in both the directions along the
bus. When the destination terminal sees the data,
it copies it to the local disk.
Advantages of Bus Topology
These are the advantages of using bus topology −
 Easy to install and maintain
 Can be extended easily
 Very reliable because of single transmission line.
Disadvantages of Bus Topology
These are some disadvantages of using bus topology −
 Troubleshooting is difficult as there is no single point of control
 One faulty node can bring the whole network down.
 Dumb terminals cannot be connected to the bus.
Star Topology
 In star topology, server is connected to each node individually.
 Server is also called the central node.
 Any exchange of data between two nodes must take place through the server.
 It is the most popular topology for information and voice networks as central node can
process data received from source node before
sending it to the destination node.
Advantages of Star Topology
These are the advantages of using star topology −
 Failure of one node does not affect the network
 Troubleshooting is easy as faulty node can be
detected from central node
 immediately
 Simple access protocols required as one of the
communicating nodes is always the central
node
Disadvantages of Star Topology
These are the disadvantages of using star topology −
 Long cables may be required to connect each node to the server
 Failure of central node brings down the whole network

Tree Topology
 Tree topology has a group of star networks connected to a linear bus backbone cable.
 It incorporates features of both star and bus topologies.
 Tree topology is also called hierarchical topology.
Advantages of Tree Topology
These are some of the advantages of using tree topology −
 Existing network can be easily expanded
 Point-to-point wiring for individual segments means easier
installation and maintenance.
 Well suited for temporary networks.
Disadvantages of Tree Topology
These are some of the disadvantages of using tree topology −
 Technical expertise required to configure and wire tree
topology
 Failure of backbone cable brings down entire network
 Insecure network
 Maintenance difficult for large networks.
Types of Networks
 Networks can be categorized depending on size, complexity, level of security, or
geographical range.
 Some of the most popular topologies based on geographical spread.
PAN
 PAN is the acronym for Personal Area Network.
 PAN is the interconnection between devices within the range of a person’s private
space, typically within a range of 10 meters.
 If you have transferred images or songs from your laptop to mobile or from mobile to
your friend’s mobile using Bluetooth, you have set up and used a personal area
network.
 A person can connect her laptop, smart phone, personal digital assistant an portable
printer in a network at home. This network could be fully Wi-Fi or a combination of wired
and wireless.

LAN
 LAN or Local Area Network is a wired network spread over a single site like an office,
building or manufacturing unit.
 LAN is set up to when team members need to share software and hardware resources
with each other but not with the outside world.
 Typical software resources include official documents, user manuals, employee
handbook, etc. Hardware resources that can be easily shared over the network include
printer, fax machines, modems, memory space, etc.
 This decreases infrastructure costs for the organization drastically.
 A LAN may be set up using wired or wireless connections.
 A LAN that is completely wireless is called Wireless LAN or WLAN.

MAN
 MAN is the acronym for Metropolitan Area Network.
 It is a network spread over a city, college campus or a small region.
 MAN is larger than a LAN and typically spread over several kilometers.
 Objective of MAN is to share hardware and software resources, thereby decreasing
infrastructure costs.
 MAN can be built by connecting several LANs.
 The most common example of MAN is cable TV network.

WAN
 WAN or Wide Area Network is spread over a country or many countries.
 WAN is typically a network of many LANs, MANs and WANs.
 Network is set up using wired or wireless connections, depending on availability and
reliability.
 The most common example of WAN is the Internet.

You might also like