100W Single Output DC-DC Converter SD-100 series

Features :
2:1 wide input range
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
Fixed switching frequency at 83KHz
24V and 48V input voltage design refer to LVD
Low cost
High reliability
2 years warranty
(for D type only)
SPECIFICATION
MODEL SD-100B-5 SD-100C-5 SD-100D-5 SD-100B-12 SD-100C-12 SD-100D-12 SD-100B-24 SD-100C-24 SD-100D-24
DC VOLTAGE 5V 12V 24V
RATED CURRENT 20A 8.5A 4.2A
CURRENT RANGE 0 ~ 20A 0 ~ 8.5A 0 ~ 4.2A
RATED POWER 100W 102W 100.8W
RIPPLE & NOISE (max.) Note.2 100mVp-p 120mVp-p 150mVp-p
OUTPUT VOLTAGE ADJ. RANGE 4.5 ~ 5.5VDC 11 ~ 16VDC 23 ~ 30VDC
VOLTAGE TOLERANCE Note.3 2.0% 1.0% 1.0%
LINE REGULATION 0.5% 0.3% 0.2%
LOAD REGULATION 0.5% 0.3% 0.2%
SETUP, RISE TIME 2s, 50ms(only D mode) at full load
HOLD UP TIME (Typ.) 20ms(only D mode) at full load
VOLTAGE RANGE B:19 ~ 36VDC C:36 ~ 72VDC D:72 ~ 144VDC or 85 ~ 132VAC
EFFICIENCY (Typ.) 74% 75% 76% 75% 77% 80% 78% 81% 83%
INPUT DC CURRENT (Typ.) 4.8A/24V 2.4A/48V 1.8A/96V 4.8A/24V 2.4A/48V 1.8A/96V 4.8A/24V 2.4A/48V 1.8A/96V
INRUSH CURRENT (Typ.) D:18A/96VDC
LEAKAGE CURRENT <0.75mA/120VAC(SD-100D)
105 ~ 135% rated output power
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION
5.75 ~ 6.75V/10% load 16.8 ~ 20V/10% load 31.5 ~ 37.5V/10% load
OVER VOLTAGE
Protection type : Hiccup mode, recovers automatically after fault condition is removed
WORKING TEMP. -10 ~ +60 (Refer to output load derating curve)
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85, 10 ~ 95% RH
TEMP. COEFFICIENT 0.03%/ (0 ~ 50)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS IEC60950-1 CB approved by TUV (for D type only)
SAFETY & WITHSTAND VOLTAGE I/P-O/P:1.5KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH
(Note 4) EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
EMS IMMUNITY Compliance to EN61000-4-2,3,4,6,8; ENV50204, light industry level, criteria A
MTBF 356.7K hrs min.(SD-100B) 355.5K hrs min.(SD-100C) 341.9K Hrs min.(SD-100D) MIL-HDBK-217F (25)
OTHERS DIMENSION 199*98*38mm (L*W*H)
PACKING 0.65Kg; 20pcs/13.8Kg/0.8CUFT
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25of ambient temperature.
NOTE
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to
perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)

File Name:SD-100-SPEC 2015-08-06

 100W Single Output DC-DC Converter SD-100 series

Mechanical Specification Case No. 902 Unit:mm

197

7
12

3.5
1
2
9.5

85.5
4

98
80

5
8.2

6
7
3
3.5 M
4-
Terminal Pin No. Assignment
Pin No. Assignment Pin No. Assignment
4.5 57.5 120
1,2 INPUT 4,5 DC OUTPUT -V
199
3 FG 6,7 DC OUTPUT +V

190
SD-100B,C
6.5
Pin No. Assignment
1 DC INPUT V+
9.5
9

18

2 DC INPUT V-

3.5
3.5

SD-100D
18

38

3-M
28.5

3
Pin No. Assignment
1,2 AC/DC INPUT
22 157

Block Diagram fosc : 83KHz

EMI POWER RECTIFIERS +V

I/P FILTER SWITCHING &
-V
FILTER

FG DETECTION
PWM CIRCUIT
O.L.P.
CONTROL

O.V.P.

Derating Curve Static Characteristics(SD-100D-24V)

Ta=25
SD-100C,D-24 32 350
100
OUTPUT RIPPLE (mVp-p)

28 300
OUTPUT VOLTAGE (V)

80
24 250
SD-100B-5,12,24
60 SD-100C,D-5,12 20 200
LOAD (%)

16 150
40
12 100
20
8 50

-10 0 10 20 30 40 50 60 (VERTICAL) 55 60 65 70 75 80 90 100 110 120 130

-10 0 45 55 (HORIZONTAL)

AMBIENT TEMPERATURE () INPUT VOLTAGE (V)

File Name:SD-100-SPEC 2015-08-06