120W DIN Rail Type DC-DC Converter DDR-120 series

IEC62368-1 UL62368-1 AS/NZS 62368.1 TPTC004

■ Features ■ Applications

Compliance to EN50155 and EN45545-2 railway standard
Bus,tram,metro or railway system

Width only 32mm
Industrial control system

2:1 wide input range
Semi-conductor fabrication equipment

-40~+70℃ wide working temperature
Factory automation

150% peak load capability
Electro-mechanical

DC output adjustable
Wireless network

Cooling by free air convection
Telecom or datacom system

Can be installed on DIN rail TS-35/7.5 or 15

Protections: Short circuit / Overload / Over voltage /
Input reverse polarity / Input under voltage protection

4KVdc I/O isolation(Reinforced isolation)

3 years warranty

■ Description
DDR-120 series is a 120W DIN Rail type DC-DC converter with main features including DIN rail-type easy installation,
ultra slim width (32mm), 2:1 wide input voltage, fanless design, -40~+70℃ wide operating temperature, 4KVdc
I/O isolation, 150% peak load, adjustable output voltage and full protective functions.
This series of models has various input options: 9~18V / 16.8~33.6V / 33.6~67.2V / 67.2~154V and various
output options: 12V / 24V / 48V and can be used for industrial & railway control, security control, communication
system and other fields. Suitable applications include DC buck/boost regulator, increasing system insulation level
and voltage drop compensation along cable...etc.

■ Model Encoding
DDR - 120 A - 24

Output voltage(12/24/48Vdc)
Input voltage (A: 9~18Vdc, B:16.8~33.6Vdc, C:33.6~67.2Vdc, D:67.2~154Vdc)
Rated wattage
Series name

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series
SPECIFICATION
MODEL DDR-120A-12 DDR-120A-24 DDR-120A-48 DDR-120B-12 DDR-120B-24 DDR-120B-48
DC VOLTAGE 12V 24V 48V 12V 24V 48V
RATED CURRENT 8.3A 4.2A 2.1A 10A 5A 2.5A
CURRENT RANGE 0 ~ 8.3A 0 ~ 4.2A 0 ~ 2.1A 0 ~ 10A 0 ~ 5A 0 ~ 2.5A
RATED POWER 99.6W 100.8W 100.8W 120W 120W 120W
PEAK CURRENT 12.45A 6.3A 3.15A 15A 7.5A 3.75A
PEAK POWER Note.5 150W (3sec.) 180W (3sec.)
OUTPUT RIPPLE & NOISE (max.) Note.2 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p
VOLTAGE ADJ. RANGE 9 ~ 14V 24 ~ 28V 48 ~ 56V 9 ~ 14V 24 ~ 28V 48 ~ 56V
VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
LOAD REGULATION ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0%
SETUP, RISE TIME 500ms, 60ms @12Vdc 500ms, 60ms @24Vdc
HOLD UP TIME (Typ.) Please refer to page 7 Hold up Time( Load de-rating curve )
VOLTAGE RANGE Note.4 9 ~ 18Vdc 9 ~ 18Vdc 9 ~ 18Vdc 16.8 ~ 33.6Vdc 16.8 ~ 33.6Vdc 16.8 ~ 33.6Vdc
EFFICIENCY (Typ.) 88.5% 88.5% 88.5% 89% 89.5% 91%
DC CURRENT (Typ.) 11.2A @12Vdc 5.6A @24Vdc
INPUT
INRUSH CURRENT (Typ.) 5A @12Vdc 5A @ 24Vdc
EN50155:2007-comply with 3ms@ full load EN50155:2007-comply with S1 level (6ms) @ full load, S2 level (10ms) @ 70% load
INTERRUPTION OF VOLTAGE SUPPLY
EN50155:2017-comply with S1 level EN50155:2017-comply with S1 level
Normally works within 150% rated output power for more than 3 seconds and then constant current protection 105~135%
OVERLOAD
rated output power with auto-recovery
PROTECTION 14.4 ~ 16.8V 28.8 ~ 33.6V 57.6 ~ 67.2V 14.4 ~ 16.8V 28.8 ~ 33.6V 57.6 ~ 67.2V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
REVERSE POLARITY By internal MOSFET, no damage, recovers automatically after fault condition removed
UNDER VOLTAGE LOCKOUT 12Vin (A - type) :Power ON≥9V , OFF≤8.5V 24Vin (B - type) :Power ON≥16.8V , OFF≤16.5V
WORKING TEMP. -40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 5 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 5 ~ 95% RH non-condensing
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 55℃)
VIBRATION Component:10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC61373
OPERATING ALTITUDE 5000 meters
SAFETY STANDARDS IEC 62368-1, UL 62368-1, EAC TP TC 004, AS/NZS 62368.1 approved; Design refer to UL508
WITHSTAND VOLTAGE I/P-O/P:4KVdc I/P-FG:2.5KVdc O/P-FG:2.5KVdc
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500Vdc / 25℃/ 70% RH
Parameter Standard Test Level / Note
Conducted EN55032 Class B
EMC EMISSION Radiated EN55032 Class B
Voltage Flicker EN61000-3-3 -----
SAFETY & Harmonic Current ----- -----
EMC
(Note 6) EN55024 , EN61000-6-2(EN50082-2)
Parameter Standard Test Level / Note
ESD EN61000-4-2 Level 3, 8KV air ; Level 3, 6KV contact; criteria A
Radiated EN61000-4-3 Level 3, 10V/m ; criteria A
EFT / Burst EN61000-4-4 Level 3, 2KV ; criteria A
EMC IMMUNITY
Surge EN61000-4-5 Level 3, 1KV/Line-Line ;Level 3, 2KV/Line-Line-FG ;criteria A
Conducted EN61000-4-6 Level 3, 10V ; criteria A
Magnetic Field EN61000-4-8 Level 4, 30A/m ; criteria A
Compliance to EN45545-2 for fire protection ; Meet EN50155 / IEC60571 including IEC61373 for shock & vibration,
RAILWAY STANDARD
EN50121-3-2 for EMC (except for 9~18Vin)
MTBF 214.6K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 32*125.2*102mm (W*H*D)
PACKING 510g; 28pcs/15.3Kg/1.22CUFT
1. All parameters NOT specially mentioned are measured at normal input (A:12Vdc , B:24Vdc) , rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μf & 47μf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the derating curve for more details.
5. 3 seconds max., please refer to peak loading curves.
NOTE
6. The power supply is considered as an independent unit, but the final equipment still need to re-confirm that the whole system complies with
the EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than
2000m(6500ft).
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:DDR-120-SPEC 2020-10-20
 120W DIN Rail Type DC-DC Converter DDR-120 series
SPECIFICATION
MODEL DDR-120C-12 DDR-120C-24 DDR-120C-48 DDR-120D-12 DDR-120D-24 DDR-120D-48
DC VOLTAGE 12V 24V 48V 12V 24V 48V
RATED CURRENT 10A 5A 2.5A 10A 5A 2.5A
CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~ 2.5A 0 ~ 10A 0 ~ 5A 0 ~ 2.5A
RATED POWER 120W 120W 120W 120W 120W 120W
PEAK CURRENT 15A 7.5A 3.75A 15A 7.5A 3.75A
PEAK POWER Note.5 180W (3sec.)
OUTPUT RIPPLE & NOISE (max.) Note.2 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p
VOLTAGE ADJ. RANGE 9 ~ 14V 24 ~ 28V 48 ~ 56V 9 ~ 14V 24 ~ 28V 48 ~ 56V
VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
LOAD REGULATION ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0%
SETUP, RISE TIME 500ms, 60ms @48Vdc 500ms, 60ms @110Vdc
HOLD UP TIME (Typ.) Please refer to page 7 Hold up Time( Load de-rating curve )
VOLTAGE RANGE Note.4 33.6 ~ 67.2Vdc 33.6 ~ 67.2Vdc 33.6 ~ 67.2Vdc 67.2 ~ 154Vdc 67.2 ~ 154Vdc 67.2 ~ 154Vdc
EFFICIENCY (Typ.) 89.5% 91% 92% 89.5% 91% 91.5%
DC CURRENT (Typ.) 2.8A @48Vdc 1.3A @110Vdc
INPUT
INRUSH CURRENT (Typ.) 5A @48Vdc 5A @110Vdc
EN50155:2007-comply with S1 level (6ms) @ full load, S2 level (10ms) @ 60% load EN50155:2007-comply with S2 level (10ms) @ full load
INTERRUPTION OF VOLTAGE SUPPLY
EN50155:2017-comply with S1 level EN50155:2017-comply with S1 level
Normally works within 150% rated output power for more than 3 seconds and then constant current protection 105~135%
OVERLOAD
rated output power with auto-recovery
PROTECTION 14.4 ~ 16.8V 28.8 ~ 33.6V 57.6 ~ 67.2V 14.4 ~ 16.8V 28.8 ~ 33.6V 57.6 ~ 67.2V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
REVERSE POLARITY By internal MOSFET, no damage, recovers automatically after fault condition removed
UNDER VOLTAGE LOCKOUT 48Vin (C - type) :Power ON≥33.6V , OFF≤33V 110Vin (D - type):Power ON≥67.2V , OFF≤65V
WORKING TEMP. -40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 5 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 5 ~ 95% RH non-condensing
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 55℃)
VIBRATION Component:10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC61373
OPERATING ALTITUDE 5000 meters
SAFETY STANDARDS IEC 62368-1, UL 62368-1, EAC TP TC 004, AS/NZS 62368.1 approved; Design refer to UL508
WITHSTAND VOLTAGE I/P-O/P:4KVdc I/P-FG:2.5KVdc O/P-FG:2.5KVdc
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500Vdc / 25℃/ 70% RH
Parameter Standard Test Level / Note
Conducted EN55032 Class B
EMC EMISSION Radiated EN55032 Class B
Voltage Flicker EN61000-3-3 -----
SAFETY & Harmonic Current ----- -----
EMC
(Note 6) EN55024 , EN61000-6-2(EN50082-2)
Parameter Standard Test Level / Note
ESD EN61000-4-2 Level 3, 8KV air ; Level 3, 6KV contact; criteria A
Radiated EN61000-4-3 Level 3, 10V/m ; criteria A
EFT / Burst EN61000-4-4 Level 3, 2KV ; criteria A
EMC IMMUNITY
Surge EN61000-4-5 Level 3, 1KV/Line-Line ;Level 3, 2KV/Line-Line-FG ;criteria A
Conducted EN61000-4-6 Level 3, 10V ; criteria A
Magnetic Field EN61000-4-8 Level 4, 30A/m ; criteria A
RAILWAY STANDARD Compliance to EN45545-2 for fire protection ; Meet EN50155 / IEC60571 including IEC61373 for shock & vibration,
EN50121-3-2 for EMC
MTBF 214.6K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 32*125.2*102mm (W*H*D)
PACKING 510g; 28pcs/15.3Kg/1.22CUFT
1. All parameters NOT specially mentioned are measured at normal input (C:48Vdc , D:110Vdc) , rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μf & 47μf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the derating curve for more details.
5. 3 seconds max., please refer to peak loading curves.
NOTE 6. The power supply is considered as an independent unit, but the final equipment still need to re-confirm that the whole system complies with
the EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than
2000m(6500ft).
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:DDR-120-SPEC 2020-10-20
 120W DIN Rail Type DC-DC Converter DDR-120 series

Block Diagram
fosc : 65KHz

EMI POWER RECTIFIERS +Vo

I/P FILTER SWITCHING &
-Vo
FILTER

FG DETECTION
PWM CIRCUIT
O.L.P. CONTROL

O.V.P.

Derating Curve Output derating VS input voltage

100

90
150 85
80 B/C/D Type
120 For 3 sec. (typ.)
70 A Type
100
LOAD (%)

LOAD (%)

80 60
Continuous
50
40
40

-40 -30 -20 -10 0 10 20 30 40 50 55 60 70 A Type: 9 10.8 12 15 18

(VERTICAL) B Type: 16.8 21.6 24 30 33.6
C Type: 33.6 43.2 48 60 67.2
D Type: 67.2 86.4 96 110 154

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE

Peak Loading
(1) (2)

150% Load 150% Load

100% Load 40% Load

100 sec. 3 sec. 10 sec. 3 sec.

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series

Input Fuse
There is a fuse connected in series to the positive input line, which is used to protect against abnormal surge. Fuse specifications
of each model are shown as below.

Type Fuse Type Reference and Rating

A Time-Lag Conquer MST, 10A, 250V *2
B Time-Lag Conquer MST, 8A, 250V *2
C Time-Lag Conquer MST, 8A, 250V *1
D Time-Lag Conquer MST, 4A, 250V *1

Input Under-Voltage Protection

If input voltage drops below Vimin, the internal control IC shuts down and there is no output voltage. It recovers automatically
when input voltage reaches above Vimin,please refer to the cruve below.

DDR-120A-24 DDR-120B-24
Vo 30 Vo 30
25 25

20 20

15 Turn On 15 Turn On
Turn Off Turn Off
10 10

5 5
8. 5 16 . 5 16.8
0 Vin 0 Vin
8 9 10 15 16 17 15 16 17 18 19 20

DDR-120C-24 DDR-120D-24
Vo 30 Vo 30
25 25

20 20

15 Turn On 15 Turn On
Turn Off Turn Off
10 10

5 5
33.6 65 67.2
0 Vin 0 Vin
31 33 34 35 36 37 65 66 67 68 69 70

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series

Input Reverse Polarity Protection

There is a MOSFET connected in series to the negative input line. If the input polarity is connected reversely, the MOSFET opens
and there will be no output to protect the unit.

Input Range and Transient Ability

The series has a wide range input capability. With -30% / +40% of rated input voltage(except A Type), it can withstand that for 1 second.

Inrush Current
Inrush current is suppressed by a current limit circuit during the initial start-up, and then the circuit is bypassed by a MOSFET to
reduce power consumption after accomplishing the start-up.

Power start

Normal current
Inrush current limit

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series

Hold-up Time
EN50155: 2007 version - D type is in compliance with S2 level (10ms), while A types are in compliance with S1 level (3ms) at full load output
condition. To fulfil the requirements of S2 level (10ms), B types require de-rating their output load to 70%, C types
require de-rating their output load to 60%, please refer to the curve diagrams below.

DDR-120A-12 DDR-120A-24 DDR-120A-48

100% 100% 100%
90% 90% 90%
80% 80% 80%
70% 70% 70%
LOAD

LOAD

LOAD
60% 60% 60%
50% 50% 50%
40% 40% 40%
30% 30% 30%
20% 20% 20%
10% 10% 10%
0% 0% 0%
0ms 10ms 20ms 30ms 40ms 50ms 60ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms

TIME TIME TIME

DDR-120B-12 DDR-120B-24 DDR-120B-48

100% 100% 100%
90% 90% 90%
80% 80% 80%
70% 70% 70%
LOAD

LOAD

LOAD
60% 60% 60%
50% 50% 50%
40% 40% 40%
30% 30% 30%
20% 20% 20%
10% 10% 10%
0% 0% 0%
0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 90ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 90ms

TIME TIME TIME

DDR-120C-12 DDR-120C-24 DDR-120C-48

100% 100% 100%
90% 90% 90%
80% 80% 80%
70% 70% 70%
LOAD

LOAD

LOAD

60% 60% 60%

50% 50% 50%
40% 40% 40%
30% 30% 30%
20% 20% 20%
10% 10% 10%
0% 0% 0%
0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms

TIME TIME TIME

DDR-120D-12 DDR-120D-24 DDR-120D-48

100% 100% 100%
90% 90% 90%
80% 80% 80%
70% 70% 70%
LOAD

LOAD

LOAD

60% 60% 60%

50% 50% 50%
40% 40% 40%
30% 30% 30%
20% 20% 20%
10% 10% 10%
0% 0% 0%
0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 90ms 100ms 110ms 120ms 130ms 0ms 10ms 20ms 30ms 40ms 50ms 60ms 70ms 80ms 90ms 100ms 110ms 120ms 130ms

TIME TIME TIME

EN50155: 2017 version - Comply with S1 level (6ms)

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series

Efficiency vs Load & Vin Curve

The efficiency vs load & Vin curves of each model are shown as below.

DDR-120A-12 DDR-120A-24 DDR-12A-48

95% 95% 95%
EFFICIENCY

EFFICIENCY

EFFICIENCY
90% 90% 90%

85% 85% 85%

12Vdc 12Vdc 12Vdc
80% 15.6Vdc 80% 15.6Vdc 80% 15.6Vdc
10.8Vdc 10.8Vdc 10.8Vdc
75% 75% 75%

70% 70% 70%

10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

LOAD LOAD LOAD

DDR-120B-12 DDR-120B-24 DDR-120B-48

95% 95% 95%
EFFICIENCY

EFFICIENCY

EFFICIENCY
90% 90% 90%

85% 85% 85%

24Vdc 24Vdc 24Vdc
80% 31.2Vdc 80% 31.2Vdc 80% 31.2Vdc
16.8Vdc 16.8Vdc 16.8Vdc
75% 75% 75%

70% 70% 70%

10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

LOAD LOAD LOAD

DDR-120C-12 DDR-120C-24 DDR-120C-48

95% 95% 95%
EFFICIENCY

EFFICIENCY

EFFICIENCY

90% 90% 90%

85% 85% 85%

48Vdc 48Vdc 48Vdc
80% 80% 80%
33.6Vdc 33.6Vdc 33.6Vdc
75% 67.2Vdc 75% 67.2Vdc 75% 67.2Vdc
70% 70% 70%
65% 65% 65%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD LOAD LOAD

DDR-120D-12 DDR-120D-24 DDR-120D-48

95% 95% 95%
EFFICIENCY

EFFICIENCY

EFFICIENCY

90% 90% 90%

85% 85% 85%
80% 110Vdc 80% 80% 110Vdc
110Vdc
75% 77Vdc 75% 75% 77Vdc
77Vdc
70% 143Vdc 70% 70% 143Vdc
143Vdc
65% 65% 65%
60% 60% 60%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

LOAD LOAD LOAD

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series

Immunity to Environmental Conditions

Test method Standard Test conditions Status

Cooling Test EN 50155 section 12.2.3 (Column 2, Class TX) Temperature: -40℃ No damage
EN 60068-2-1 Dwell Time: 2 hrs/cycle

EN 50155 section 12.2.4 (Column 2, Class TX)

Temperature: 70℃ / 85℃
Dry Heat Test EN 50155 section 12.2.4 (Column 3, Class TX & Column 4, Class TX) PASS
Duration: 6 hrs / 10min
EN 60068-2-2
Temperature: 25℃~55℃
EN 50155 section 12.2.5
Damp Heat Test, Cyclic Humidity: 90%~100% RH PASS
EN 60068-2-30
Duration: 48 hrs

EN 50155 section 12.2.11 Temperature: 19℃

Vibration Test Humidity: 65% PASS
EN 61373
Duration: 10 mins

Temperature: 19℃
EN 50155 section 12.2.11 Humidity: 65%
Increased Vibration Test PASS
EN 61373 Duration: 5 hrs

Temperature: 21± 3℃
Shock Test
EN 50155 section 12.2.11 Humidity: 65 ± 5% PASS
EN 61373 Duration: 30ms*18

EN 50155 section 12.2.3 (Column 2, Class TX) Temperature: -40℃

Low Temperature Storage Test PASS
EN 60068-2-1 Dwell Time: 16 hrs

EN 50155 section 12.2.10 (Class ST4) Temperature: 35℃±2℃

Salt Mist Test PASS
Duration: 96 hrs

EN45545-2 Fire Test Conditions

Test Items Hazard Level

Items Standard HL1 HL2 HL3

EN 45545-2:2013
Oxygen index test PASS PASS PASS
EN ISO 4589-2:1996

EN 45545-2:2013
R22 Smoke density test PASS PASS PASS
EN ISO 5659-2:2006

EN 45545-2:2013
Smoke toxicity test PASS PASS PASS
NF X70-100:2006

EN 45545-2:2013
R24 Oxygen index test PASS PASS PASS
EN ISO 4589-2:1996

EN 45545-2:2013
R25 Glow-wire test PASS PASS PASS
EN 60695-2-11:2000

EN 45545-2:2013
R26 Vertical flame test PASS PASS PASS
EN 60695-11:2003

File Name:DDR-120-SPEC 2020-10-20

 120W DIN Rail Type DC-DC Converter DDR-120 series

Mechanical Specification
Case No. Unit:mm

32

Terminal Pin No. Assignment (TB2)

Pin No. Assignment
1,2 DC Output -Vo
3,4 DC Output +Vo
Top View

102

TB2

1234
(No Use)

+Vo
Adj.
125.2

123

TB1
Side View Front View Side View

Terminal Pin No. Assignment (TB1)

Pin No. Assignment
1 FG
35

2 DC Input -Vin
3 DC Input +Vin
ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15

Bottom View

Installation Manual
Please refer to : http://www.meanwell.com/manual.html

File Name:DDR-120-SPEC 2020-10-20