VL-1 W Series

lWUnregulated Single & Dual output

Features
■ 7 Pin SIL Package
■ 6000 VDC High Isolation
■ Physical Clearance of Isolation Barrier 2.5mm
■ Low Ripple and Noise
■ Efficiency up to 81%
■ Long Term Short Circuit Protection
■ -40 ~ 85 ° C Operation Temperature Range
■ 100% safety production test
■ Rated working voltage for 250Vrms and 400Vdc
■
■
Low coupling capacity
Dedicated for IGBT applications CE
T he VL series is a family of cost effective 1W single & dual output DC-DC converters. T hese converters achieve low cost and miniature
SIP size without compromising performance . T he bigger case ensures the physical clearance of isolation barrier of 2.5mm, which
increases the reliability under hipot from 6KVDC. Devices are encapsulated with flame retardant resin. Input voltages are
5V,9V, 12V, 15V,24Vdc. with output voltage of 3.3V,5V,9V, 12V, 15V, ±3.3V, ±5V, ±9V, ±12V, ±15 and +15/-9Vdc. Special featuring long term
output short circuit protection . Standard features include an input range of ±10% tolerance and low output noise and ripple.

All specifications typical at Ta = 25° C, nominal input voltage and full load unless otherwise specified
PHYSICAL SPECIFICATIONS
Clearance Distance (Input to Output) 2.5 mm
CaseMaterial E enca sulated UL94V-0 rated
(From 10% to 100% Load) ±10% ,max. Pin Material 0.5mm Alloy 42 Solder-coated
200mVpk-pk ,max. Pottin Material

Short Circuit Protection Indefinite (Automatic Recovery)

Tern erature Coefficient ±0.03 re
Capacitor Load(2) See Table ,max.

±10% ,max. ABSOLUTE MAXIMUM RATINGS(4)

See sole T hese are stress ratings. Exposure of devices to any of these
See Table ,max. conditions may adversely affect long-term reliability.
Ca acitor In put Surge oltage 00mS
Input Reflected Ripple Current(3) 20mApk-pk ,typ. 5Models 7 Vdc,max.
9Models 12 Vdc,max.
12Models 15Vdc,max.
GENERAL SPECIFICATIONS 15Models
Efficiency 24Models
1/0 Isolation Volta e 60sec Soldering Temperature 260 ° C ,max.
1/0 Isolation Capacitance (1.5mm from case 10sec max.)

I O solation Resistance
Switching Frequency 20~50KHz ,typ.
Humidity 9 5% rel H
Reliability Calculated MTBF(MIL-HDBK-217 F) >2.39 Mhrs
CL ASS B
Safet Standard : deal ned to meet
CLASSB
ENVIRONMENT SPECIFICATIONS ESD IEC 61000-4-2 Pert. Criteria A
Operating Temperature -40 ° C-85 ° C RS IEC 61000-4-3 Perf. Criteria A
Maximum Case TemDerature 100 ° c 1 EFT (7) IEC 61000-4-4 Pert. Criteria A
Storage Temperature -40 ° C-125 ° C cs IEC 61000-4-6 Perf. Criteria A
Cooling Nature Convection I PFMF IEC 61000-4-8 Pert. Criteria A
VL -1 W Unregulated Single & Dual output

PART NUMBER STRUCTURE

Derating Curve

100%
0
Series Name
� 75%
Input Voltage Range -I
Output Type
05-SV SS - Single output
09- 9V S - Dual Output � 50%
12-12V m
15-15V ;o
24-24V
25%
Nominal Output Voltage
3R3-3.3V
05-SV
09- 9V
12-12V -40 -20 0 20 40 60 80 � 100 120
5
15-15V AMBIENTTEMPERATURE( ° C)

--
1509-15V/-9V

MODEL SELECTION GUIDE

111:■IIWI-
I INPUT INPUT Current OUTPUT Current
MODEL NUMBER Voltage Range Full load I• t f

I Vdc mA .
VL-053R3SSH6 4.5-5.5 30 266.67 3R3 303.03 75 220
VL-0505SSH6 4.5-5.5 30 259.74 5 200 77 220
VL-0509SSH6 4.5-5.5 30 253.16 9 111.11 79 220
VL-0512SSH6 4.5-5.5 45 250.00 12 83.33 80 220
VL-0515SSH6 4.5-5.5 40 253.16 15 66.67 79 220
VL-093R3SSH6 8.1-9.9 20 146.20 3R3 303.03 76 220
VL-0905SSH6 8.1-9.9 25 144.30 5 200 77 220
VL-0909SSH6 8.1-9.9 25 138.89 9 111.11 80 220
VL-0912SSH6 8.1-9.9 25 135.50 12 83.33 82 220
VL-0915SSH6 8.1-9.9 25 135.50 15 66.67 82 220
VL-123R3SSH6 10.8-13.2 20 112.61 3R3 303.03 74 220
VL-1205SSH6 10.8-13.2 20 105.49 5 200 79 220
VL-1209SSH6 10.8-13.2 20 106.84 9 111.11 78 220
VL-1212SSH6 10.8-13.2 20 104.17 12 83.33 80 220
VL-1215SSH6 10.8-13.2 20 101.63 15 66.67 82 220
VL-153R3SSH6 13.5-16.5 15 86.58 3R3 303.03 77 220
VL-1505SSH6 13.5-16.5 15 84.39 5 200 79 220
VL-1509SSH6 13.5-16.5 15 82.30 9 111.11 81 220
VL-1512SSH6 13.5-16.5 15 81.30 12 83.33 82 220
VL-1515SSH6 13.5-16.5 15 81.30 15 66.67 82 220
VL-243R3SSH6 21.6-26.4V 15 56.31 3R3 303.03 74 220
VL-2405SSH6 21.6-26.4V 15 56.31 5 200 74 220
VL-2409SSH6 21.6-26.4V 15 55.56 9 111.11 75 220
VL-2412SSH6 21.6-26.4V 15 51.44 12 83.33 81 220
VL-2415SSH6 21.6-26.4V 15 52.74 15 66.67 79 220
VL-053R3SH6 4.5-5.5 30 270.27 ±3R3 +/-151.52 74 ±100
VL-0505SH6 4.5-5.5 30 253.16 ±5 +/-100 79 ±100
VL-0509SH6 4.5-5.5 30 246.91 ±9 +/-55.56 81 ±100
VL-0512SH6 4.5-5.5 40 250.00 ±12 +/-41.67 80 ±100
VL-0515SH6 4.5-5.5 40 250.00 ±15 +/-33.33 80 ±100
VL-093R3SH6 8.1-9.9 25 146.20 ±3R3 +/-151.52 76 ±100
VL-0905SH6 8.1-9.9 25 138.89 ±5 +/-100 80 ±100
VL-0909SH6 8.1-9.9 25 135.50 ±9 +/-55.56 82 ±100
VL-0912SH6 8.1-9.9 25 135.50 ±12 +/-41.67 82 ±100
VL-0915SH6 8.1-9.9 25 133.87 ±15 +/-33.33 83 ±100
VL-123R3SH6 10.8-13.2 20 109.65 ±3R3 +/-151.52 76 ±100
VL-1205SH6 10.8-13.2 20 108.23 ±5 +/-100 77 ±100
VL-1209SH6 10.8-13.2 20 104.17 ±9 +/-55.56 80 ±100
VL-1212SH6 10.8-13.2 20 102.88 ±12 +/-41.67 81 ±100
VL-1215SH6 10.8-13.2 20 102.88 ±15 +/-33.33 81 ±100

2
VL -1 W Unregulated Single & Dual output

--
MODEL SELECTION GUIDE

MODEL NUMBER
INPUT
Voltage Range
(Vdc) --■-
INPUT Current OUTPUT Current
Full load
mA
.. � .
.. . .
VL-153R3SH6 13.5-16.5 15 86.58 ±3R3 +/-151.52 77 ±100
VL-1505SH6 13.5-16.5 15 82.30 ±5 +/-100 81 ±100
VL-1509SH6 13.5-16.5 15 80.32 ±9 +/-55.56 83 ±100
VL-1512SH6 13.5-16.5 15 79.37 ±12 +/-41.67 84 ±100
VL-1515SH6 13.5-16.5 15 78.43 ±15 +/-33.33 85 ±100
VL-243R3SH6 21.6-26.4V 15 58.69 ±3R3 +/-151.52 71 ±100
VL-2405SH6 21.6-26.4V 15 53.42 ±5 +/-100 78 ±100
VL-2409SH6 21.6-26.4V 15 52.74 ±9 +/-55.56 79 ±100
VL-2412SH6 21.6-26.4V 15 53.42 ±12 +/-41.67 78 ±100
VL-2415SH6 21.6-26.4V 15 50.81 ±15 +/-33.33 82 ±100
VL-051509SH6 4.5-5.5 40 250.00 +15/-9 +33.33/-55.55 80 ±100
VL-091509SH6 8.1-9.9 25 135.50 +15/-9 +33.33/-55.55 82 ±100
VL-121509SH6 10.8-13.2 20 105.49 +15/-9 +33.33/-55.55 79 ±100
VL-151509SH6 13.5-16.5 12 77.52 +15/-9 +33.33/-55.55 86 ±100
VL-241509SH6 21.6-26.4V 15 49.60 +15/-9 +33.33/-55.55 84 ±100

NOTE

1.Ripple/Noise measured with 20MHz bandwidth.

2.Tested by minimal Vin and constant resistive load.
3.Measured Input reflected ripple current with a simulated source inductance of 12µH
and a source capacitor Cin(47µF, ESR<1.0Q at 100KHz).
4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating.
5.0peration under no-load conditions will not damage these devices, however they may not meet all listed specifications.
6. Input filter components are be required to help meet conducted emission class B,
which application refer to the EMI Filter of design & feature configuration.
7. An external filter capacitor is required if the module has to meet IEC61000-4-4.
T he filter capacitor Motien suggest: Nippon - chemi - con KY series, 470uF/100V.

3
VL -1 W Unregulated Single & Dual output

TEST CONFIGURATIONS

Input Reflected Ripple Current Test Step L-----{)----+-----<> +Vin +Vout

Current
Input reflected ripple current is measured through Probe
a source inductor Lin(12µH) and a source capacitor DC/DC Load
Cin(47µF, ESR<1.0Q at 100KHz) at nominal input and Converter
full load. � - - - -
------<>---➔ -Vin -Vout

+Vout +Vout

Output Ripple & Noise Measurement Test DC/DC Com DC/DC

Scope Load
Converter
Converter
The Scope measuremen t bandwidth is 20MHz. Load
-Vout -Vout

EMI Filter
Input filter components (C1, L, C2 , C3) are used to help
meet conducted emissions requirement for the module.
These components should be mounted as close as
possible to the module; and all leads should be minimized
to decrease radiated noise.

C1 L C2 C3

VL-05XXXXX 1210, 2.2JJF/100V 18µH

VL-09XXXXX 1210, 2,2µF/100V 18µH

VL-12XXXXX 1210, 2.2µF/100V 18µH

VL-15XXXXX 1210, 2.2µF/100V 18µH

VL-24X.XXXX 1BµH 1210, 2,2µF/100V 1206, 470pF/2KV

1210 2.2uF/100V

MECHANICAL SPECIFICATIONS

PIN CONNECTIONS

PIN NUMBER SINGLE DUAL

1 +V Input +V Input

2 -V Input -V Input

5 -VOutput -VOutput

0.5 0 6 N.P. Common

I
(0 .0 2)
-+ll+- 7 Pin SIL Package 7 +VOutput +VOutput
2.4 0
9.8 0 ( 0.09) Notes : All dimensions are typical in millimeters ( inches).
(0.39)
t
_:t__-tt----------*- 0.25 1. Pin diameter: 0.5±0.05 ( 0.02±0.002)

t� � ��
(0.0 1) 2. Pin pitch and length tolerance: ±0.35 ( ±0.014)

--i�
3. Case Tolerance: ±0.5 ( ±0.02)

2.13 0,50
(0.0 8) (0 .02)

Last Update: 04.SEP.2018