Low Noise Printed Circuit Board Design

Matt Affeldt
November 16, 2012

Design Team 6 – ECE480

Keywords:
Low Noise, Impedance, Capacitance, PCB,

Printed Circuit Board, layout, design

Summary:
This application note is intended to be a guide for low noise, high efficiency designs of printed circuit
boards (PCB). This includes mainly layout considerations of PCBs to limit EMI between components as
well as dealing with some non-board generated noise issues.
 Low Noise PCB Design

Table of Contents
Keywords: ............................................................................................................................................... 1
Summary: ................................................................................................................................................ 1
Introduction ............................................................................................................................................ 3
Printed Circuit Board Background ............................................................................................................ 3
Printed Circuit Board Design .................................................................................................................... 4
Reducing Impedance ........................................................................................................................... 4
Avoiding Stray Capacitance .................................................................................................................. 6
Avoiding Antennas............................................................................................................................... 7
Conclusions and Recommendations ........................................................................................................ 8
References .............................................................................................................................................. 9

ECE480 Fall 2012 2 of 9

 Low Noise PCB Design

Introduction
In this application note, how to design a printed circuit board (PCB) to be low noise in order to improve
the quality of the desired circuit will be described. It is assumed that the reader has some background
knowledge of the circuits, but the basics of printed circuit boards will be described. Designing low noise
printed circuit boards requires avoiding excess impedance, stray capacitance, and antennas. Any large
impedances, stray capacitance or antennas can cause noise, instability or both. Noise is typically a high-
frequency signal on top of the desired signal. This noise can often interfere with measurement
techniques and can introduce a significant amount of inaccuracy in the results depending on how noisy
the circuit is. Instability, on the other hand, is much worse. Instability can cause complete failure of a
circuit and potentially damage components in the circuit. Stability concerns are commonly found with
operational amplifiers, and are also a concern when using most active components such as
microcontrollers and power converters. Poor planning can lead to oscillating signals which can
eventually grow, swinging voltage from ground to the power supply voltage and creates large current.
This application note will detail how to reduce noise, improve performance and avoid circuit instability.

Printed Circuit Board Background

A printed circuit board is a layer of copper that has been cut or etched in order to create electrical
connections between pads. These pads will then be connected to a component in order to realize a
specific circuit in a cleaner, more compact form than a bread board (or proto-board). These copper
layers can be stacked with an insulating epoxy in between to allow very complex circuits to be realized
on a dimensionally small board. Each layer will only make the board slightly thicker but not any wider or
longer. Each connection from one pad to another is called a trace. When it is necessary to connect one
trace to another trace on a different layer, a via can be used which is a hole that is plated with
conductive material. Finally, in multi-layer boards it is common to have ‘power planes’ such as ground
and the power supply voltage to make it easy to power and ground all the components. There is no
perfect way to design a printed circuit board. There are some specific do’s and don’ts but generally
speaking, design choices involve tradeoffs in performance between two or more attributes.

ECE480 Fall 2012 3 of 9

 Low Noise PCB Design

Printed Circuit Board Design

This section will describe how to design PCBs to reduce internal noise generated by the circuit
components and physical layout of the board. This includes suggestions to reduce impedance across
traces as well as how to keep the paths across the ground plane very low impedance, avoid stray
capacitance, avoid unwanted inductance, and avoid creating antennas. This section also discusses some
brief stability issues and how to design a PCB to avoid situations that can result in circuit instability.

Reducing Impedance
High impedance is the easiest noise source to mitigate, below are 2 examples of how to reduce
impedance-based noise from the circuit.

1. Avoid long traces. Long traces are inherently more resistive than short traces. Below in Figure 1
shows a bad example of how to lay out a component. There is a long trace between power and
the capacitor (which is polarized). Figure 2 shows that it is possible, by rotating the capacitor
180° and moving it to the right, to make the trace much shorter so as to result in a lower
impedance for the trace.

Figure 1. Long trace for connecting capacitor to power

ECE480 Fall 2012 4 of 9

 Low Noise PCB Design

Figure 2. Shorter trace for capacitor to power

2. Avoid cutting the ground plane. The following figure illustrates a top layer and ground plane.
As shown by the letter C, the ground plane has a large slot in it. This creates a large impedance
for any voltage difference between the top and bottom of the board. By cutting the holes for
the component, more like letter D, the area between the pins allows current to flow. This
significantly reduces the impedance of the ground plane. In addition, traces in the ground plane
should be avoided whenever possible. When traces in the ground plane are a necessity, avoid
making the traces as shown in A. This again cuts the ground plane into left and right sections
with a large impedance between the two halves. The letter B shows a much better path, where
it goes around the outside of the ground plane. Although this does increase the impedance of
trace B, it is better than increasing the impedance of the entire ground plane.

Figure 2. Ground Plane Trace Styles

ECE480 Fall 2012 5 of 9

 Low Noise PCB Design

Avoiding Stray Capacitance

This section will describe two techniques to help reduce the stray capacitance. It is important to be
mindful of stray capacitance, which is always present, due to stability and noise issues. Operational
amplifiers have stability issues when the input node is capacitive, and will cause oscillation on the
output of the amplifier.

1. Keep power lines away from sensitive nodes: Power traces carry a high voltage and the amount
of charge on a capacitor is equal to the voltage difference multiplied by capacitance. Although
the capacitance will be small due to the physical layout, the potentially large voltage difference
between a power trace and signal trace will cause charge to build up. When the signal voltage
changes the charge buildup can be injected into the circuit causing noise in the circuit. As
shown in Figure 3, the positive and negative power traces go around the circuit to avoid the
most critical node, the input node, to the op-amp (circled in yellow).

2. Cut the ground plane: NOTE: This suggestion comes at a price and should only be used when
necessary. Since cutting the ground plane increases the impedance of the ground plane, only do
it for nodes that are very sensitive to capacitance such as input nodes to an operational
amplifier. In Figure 3, the input node to the operational amplifier is circled. As already
discussed, inputs to operational amplifiers are particularly sensitive to capacitance which can
cause circuit instability. Multi-layer PCB are essentially capacitors, conductive plates separated
by an insulator, and therefore every node above the ground plane will have some capacitance.
To mitigate this capacitance, the ground plane (and all other planes below or above the node)
can be cut, removing the conductive plate that the node would couple with.

Figure 3. Sample board design

ECE480 Fall 2012 6 of 9

 Low Noise PCB Design

Avoiding Antennas
It is important to note that according
ccording to Texas Instruments, an an effective antenna trace is at least 1/4 λ
for a given frequency. It is given that C = λƒ where C is the speed of light, λ is the wavelength and ƒ is the
frequency. This means thatt as frequency decreases, wavelength increase and therefore the effective
size of an antenna increase. For a frequency of 100MHz, a relatively large frequency for circuits on a
PCB, the effective wavelength is 75 75cm. It is unlikely that any component on a printed circuit board is
this large and generally the entire
ire board will be less than 75
75cm.
cm. This means that components on the
board, and typically the traces as well, will not make for a good antenna however connecting cables are
often much longer than 75cm. Any cables connected to a printed circuit board can pick up noise and
then transfer that noise to the board. Figure 4 shows two different layout
layoutss of connectors on a PCB. In
Figure 4, the connectors are on opposite sides of the board. This means that that if each cable transfers a
different amount of noise to the board, there will be a voltage induced across the entire board which
will result in a noisy current traveling through all of the components. A much better layout is shown in
part b of Figure 4, where the connectors are right next to each other. Any voltage that is induced across
the board will be immediately transferred from one cable to the other and will significantly reduce the
amount of noisy current that is traveling through the board.

Figure 4.. a) Connectors on opposite

sides of the board (above) b) Shows
connectors next to each other on the
board (right)

ECE480 Fall 2012 7 of 9

 Low Noise PCB Design

Conclusions and Recommendations

As stated before, it is important to note that these are all suggestions on how to improve performance
of a board. Typically there is a trade of for each suggestion so every scenario should be reviewed
individually. Reducing noise in one part of the circuit may cost higher impedance elsewhere. Also,
sometimes it is not possible to follow some of these guidelines due to design constraints such as size or
the complexity of the circuit. Always be mindful of any specifics of the circuit that is being implemented
on a PCB and physical constraints such as connectors that have to plug into another board. For active
components, the manufacturer will often have a datasheet including some information on where parts
should be placed. For example, Texas Instruments points out that for their amplifiers a decoupling
capacitor should be placed as close to the power pin of the amplifier as possible. This suggestion from
the manufacture would trump moving the capacitor further away to allow a different trace to be
shorter.

ECE480 Fall 2012 8 of 9

 Low Noise PCB Design

References
Texas Instruments Guidelines specifically for EMI:

http://www.ti.com/lit/an/szza009/szza009.pdf

Printed Circuit Board Issues – Chapter 12 of Basic Linear Design by Hank Zumbahlen

http://www.analog.com/library/analogdialogue/archives/43-09/EDch%2012%20pc%20issues.pdf

Texas Instruments Presentation on Analog Designs of PCB

http://www.x2y.com/filters/TechDay09kr_hpa_Track2_1_Precision_Analog_Designs_Demand_GoodPCB
Layouts%20_JohnWu.pdf

ECE480 Fall 2012 9 of 9