Scribd Logo
Upload

Welcome to Scribd!

  • 347 views

    RF PCB Design Guide

    Uploaded by

    Salman Shah
    This document provides guidelines for designing printed circuit boards for high frequency radio circuits. Key recommendations include using a 4-layer board for better grounding, consulting board manufacturers for specifications, using microstrip calculators to determine track widths, keeping digital and power components away from analog RF components, avoiding right angles on RF tracks, and using via stitching and multiple vias to ground to minimize impedances.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    RF PCB Design Guide

    Uploaded by

    Salman Shah
    347 views2 pages
    This document provides guidelines for designing printed circuit boards for high frequency radio circuits. Key recommendations include using a 4-layer board for better grounding, consulting board manufacturers for specifications, using microstrip calculators to determine track widths, keeping digital and power components away from analog RF components, avoiding right angles on RF tracks, and using via stitching and multiple vias to ground to minimize impedances.

    Original Description:

    Rf Pcb Design Guide

    Original Title

    Rf Pcb Design Guide

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides guidelines for designing printed circuit boards for high frequency radio circuits. Key recommendations include using a 4-layer board for better grounding, consulting board manufacturers for specifications, using microstrip calculators to determine track widths, keeping digital and power components away from analog RF components, avoiding right angles on RF tracks, and using via stitching and multiple vias to ground to minimize impedances.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    347 views2 pages

    RF PCB Design Guide

    Uploaded by

    Salman Shah
    This document provides guidelines for designing printed circuit boards for high frequency radio circuits. Key recommendations include using a 4-layer board for better grounding, consulting board manufacturers for specifications, using microstrip calculators to determine track widths, keeping digital and power components away from analog RF components, avoiding right angles on RF tracks, and using via stitching and multiple vias to ground to minimize impedances.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    RF PCB Design Guide

    This is a general guide to the best practice printed circuit board (PCB) design rules for a high frequency or radio frequency (RF) circuit. Following these rules will help you to avoid some of the most common pitfalls in RF design. Poor layout is one of the most common causes of inadequate transmit or receive performance and EMC failures due to spurious emissions. Ideally an engineer undertaking a PCB design should be familiar with the IPC standards as these provide a rich source of information and best practice on the general principles of PCB design.

    Planning the Layout


    When planning to layout an RF PCB the first place to start is to contact your preferred board manufacturer and obtain a set of their guidelines and manufacturing capabilities, this will include the minimum track and gap widths, drill sizes and other key parameters. The board manufacturer should also be able to provide you with their standard layer stack and material data, this will include the copper weights, dielectric constant, and the thickness of core and pre-preg layers in multi-layer boards. Unless your circuit is extremely simple I suggest that a 4 layer board is used this ensures a continuous ground plane. When using a double sided board it is very difficult to ensure that the ground plane is un-broken. Another advantage of a 4 layer board is that the dimensions of the micro-strip for a 50 or 75 ohm design are more manageable.

    Use a micro-strip calculator to determine the required track width for the design impedance and ensure that it is within the manufactures capabilities, if not you may need to discuss the layer-stack with the manufacturer and select a non-standard build. Another point to note is that in my experience attempting to maintain separate ground nets for different signal area's usually causes problems rather than any benefit and is largely a throwback to the days prior to multilayer boards, a single low impedance ground plane is the safest route.

    It is quite acceptable to use FR4 for boards up-to 2.4GHz unless the highest level of performance is required. In certain circumstances it is worth specifying the board as controlled impedance to provide consistent RF performance. Having determined the track and board geometries the next step is to address the component placement. Ensure that the RF components are laid out such that all the RF tracks can be kept on the top surface with minimum length and changes of direction. Start with low signal level areas at the antenna or RF input and work backwards towards the baseband or digital area. Keep digital and power supply areas away from the analogue RF circuitry and keep all the RF components on one side of the board. Where your RF tracks can't be run in a straight line, use mitered bends if your CAD system supports them, never use right angled bends on RF signal lines. If mitered bends are not supported use a series of 45 degree bends or arcs, this minimises impedance mismatches which would increase losses and spurious emissions.

    On RF layouts it is common to provide a ground flood on the top layer and to "stitch" this to the ground plane by using multiple via's. If you intend to do this, ensure that the copper is kept a suitable distance from the RF tracks and components otherwise the impedance will be lowered and cause more harm than good. The via spacing can be 5-10mm apart there is very little benefit in stitching via's being closer than 5mm apart. Tracks to ground from RF components should be kept as short as possible and use 2 or 3 via's in parallel via's to minimize the impedance.

    You might also like