Eigrp Summary

CCNA4.
com - Free CCNA Training & Resources
EIGRP Summary
The characteristics of EIGRP follow:
 Hybrid routing protocol (distance vector that has link-state protocol

characteristics).
 Use DUAL, first proposed by E. W. Dijkstra and C. S. Scholten, to perform

distributed shortest-path routing while maintaining freedom from loops at every
instant. Although many researchers have contributed to the development of
DUAL, the most prominent work is that of J. J. Garcia-Luna-Aceves.
 Cisco Proprietary created in 1994.
 First released in IOS 9.21
 Uses IP protocol 88.
 Makes Automatic summarization on network Class boundary.
 Classless protocol (supports VLSM).
 Have the power to shut the Auto-summarization And make a configured manual
Summarization.
 Default composite metric of bandwidth and delay.
 You can factor load, MTU and reliability into the metric.
 Eigrp metric is the same as IGRP*256, It uses the smallest B.W,Reliablity,Load

& MTU with the Comulative delay upon the path…..The MTU doesn’t actually
used in the Metric calculations, But is included in the EIGRP Routing updates.
 Sends route updates to multicast address 224.0.0.10, and nei. Reply’s back with
Unicast Address.
 Sends non-periodic, partial, and bounded updates.
 Send Hello packets every 5 sec. and Hold down timer is 15 sec.
 For Low speed Hello is every 60 sec. with hold down time 180 sec.
 By default, EIGRP uses no more than 50 percent of the bandwidth of a link.

 Support for authentication via MD5 Only.
 Uses DUAL for loop prevention, and generating Succ./Fesible Succ.
 Maximum paths for Load-balancing are 6 & default is 4 , maximum are 16 in

IOS 12.3(2)T and later IOS releases
 By default, Equal-Metric load balancing. If Unequal-Metric load sharing is used

the router will load share inversely proportional to the metrics of the paths.
 Administrative distance is 90 for EIGRP internal routes, 170 for EIGRP external
routes, and 5 for EIGRP summary routes.
 Potential routing protocol for the core of a network; used in large networks.
 For neighbor relation to be established, both routers must send and receive Hello
or Ack packets from each other, they must have the same AS #, and the same
Metric K values.
 Eigrp doesn’t restrict that neighbors must have the same Hello & dead interval
timers, Unlike OSPF.
 Has a Maximum hop count of 255, the default is 100 in the last IOS releases.
The composite metric for each EIGRP route is calculated as

EIGRP metric = IGRP metric * 256
IGRP metric = [k1*BWIGRP(min) + (k2* BWIGRP(min))/(256-LOAD) + k3*DLYIGRP(sum)]

x [k5/(RELIABILITY + k4)]
If k5 is set to zero, the [k5/(RELIABILITY+k4)] term is not used.
Given the default values for k1 through k5, the composite metric calculation used by
IGRP reduces to the default metric:
IGRP metric = BWIGRP(min) + DLYIGRP(sum)
BWIGRP(min) = 107/BW(min)
DLYIGRP(sum) = DLY(sum) /10

EGRP uses multiple packet types, all identified by protocol number 88
in the IP header:
 Hellos are used by the neighbor discovery and recovery process. Hello packets are multicast and
use unreliable delivery.
 Acknowledgments (ACKs) are Hello packets with no data in them. ACKs are always unicast and
use unreliable delivery.
 Updates convey route information. Unlike RIP and IGRP updates, these packets are transmitted
only when necessary, contain only necessary information, and are sent only to routers that require
the information. When updates are required by a specific router, they are unicast. When updates
are required by multiple routers, such as upon a metric or topology change, they are multicast.
Updates always use reliable delivery.
 Queries and Replies are used by the DUAL finite state machine to manage its diffusing
computations. Queries can be multicast or unicast, and replies are always unicast. Both queries
and replies use reliable delivery.
 Requests were a type of packet originally intended for use in route servers. This application was
never implemented, and request packets are noted here only because they are mentioned in some
older EIGRP documentation.
EIGRP has four components:
Protocol-Dependent Modules (PDM): EIGRP implements modules for IP, IPX, and AppleTalk,
which are responsible for the protocol-specific routing tasks. For example, the IPX EIGRP module is
responsible for exchanging route information about IPX networks with other IPX EIGRP processes and for
passing the information to the DUAL. Additionally, the IPX module will send and receive SAP
information.
Reliable Transport Protocol (RTP): The Reliable Transport Protocol (RTP) manages the delivery
and reception of EIGRP packets. Reliable delivery means that delivery is guaranteed and that packets will
be delivered in order. If any packet is reliably multicast and an ACK is not received from a neighbor, the
packet will be retransmitted as a unicast to that unresponding neighbor. If an ACK is not received after 16
of these unicast retransmissions, the neighbor will be declared dead. The time to wait for an ACK before
switching from multicast to unicast is specified by the multicast flow timer. The time between the
subsequent unicasts is specified by the retransmission timeout (RTO). Both the multicast flow timer and
the RTO are calculated for each neighbor from the smooth round-trip time (SRTT). The SRTT is the
average elapsed time, measured in milliseconds, between the transmission of a packet to the neighbor and
the receipt of an acknowledgment. The formulas for calculating the exact values of the SRTT, the RTO,
and the multicast flow timer are proprietary.
Neighbor Discovery/Recovery: Hellos are multicast every 5 sec., minus a small random time to
prevent synchronization. & are unicast every 60 sec. On multipoint X.25, Frame Relay, and ATM
interfaces, with access link speeds of T1 or slower also it's the default for ATM SVCs and for ISDN PRI In
all cases, the Hellos are unacknowledged.
Diffusing Update Algorithm (DUAL): Used For routing calculations, loop free & convergence.
EIGRP Configuration
config)# router eigrp <AS#>

conf-router)# network < Net ID> (classlfull)
conf-router)# metric maximum-hop <#> (Up to 255, default =224)
conf-router)#passive-interface <interface>
conf-router)#distance eigrp <AS> <internal AD> <external AD>

(Define an administrative distance, default =90 & 170)
conf-router)#maximum –paths <N> (Up to 6 Links for load sharing,

Over Unequal metric paths default is 4 paths)
conf-router)#variance <#>
conf-router)#traffic-share < minimum / balanced >
conf-router)# eigrp log-neighbor-changes
conf-router)#no auto-summary (disable automatic summ. To the class boundary)

config-if)# ip summary-address eigrp <AS#> <Net ID + mask>
config-if)# bandwidth < # in Kbps>

config-if)#delay < msec>
config-if)# ip hello-interval eigrp <AS#> < sec >

config-if)# ip hold-time eigrp <AS#> < sec >
EIGRP Authentication MD5
The router may be configured to use more than one "key chain." & also different keys at different
times (key management).
Auth must be done in a fixed order rather than this you may have problems, The steps for setting
up EIGRP authentication follow:
1-Define a key chain with a name.
2- Define the authentication key or keys on the key chain
3- Define the password of the key or keys.
4- Apply MD5 authentication on an interface (EIGRP only support MD5).
5- Apply authentication on an interface and specify the key chain to be used.
6- Optionally configure key management.
Here is the cmds :

config)# key chain <name>
config-keychain)# key <#>
config-keychain-key)# key-string < password>
(start time) (End time)
config-keychain-key)#accept-lifetime<h:m:s mm dd yy>duration< mm- infinite >
config-keychain-key)#send-lifetime <h:m:s mm dd yy> duration < mm- infinite >
config)# interface <int>

config-if)# ip authentication mode eigrp <AS#><md5>
config-if)# ip authentication key-chain eigrp <AS#> <name>
# debug eigrp packets

Notes:
If the service password-encryption command is not used when implementing EIGRP
authentication, the key string will be stored as plain text in the router configuration. If
you configure the service password-encryption command, the key string will be stored
and displayed in an encrypted form; when it is displayed, there will be an encryption type
of 7 specified before the encrypted key string.
The password that is accepted from other routers and the password that is used with transmitted/sent
messages are managed separately. Both the accept-lifetime and the send-lifetime cmd. must have a
specified start time and may have either a specified duration or end time or the keyword infinite. The key
numbers are examined from the lowest to the highest, and the first valid key is used.
accept life time = accept this key

send life time = send/reply with a key for auth , based on its send lifetime.
For RIP key ID & its password isn't important to match, they will work.
BUT for EIGRP key # must match.
Show Commands
# sh ip route
# sh ip route eigrp
# sh ip route < Net ID >
# sh ip protocols
# sh ip eigrp traffic
# sh ip eigrp traffic <AS#>
# sh ip eigrp nei
# sh ip eigrp topology
# sh ip eigrp topology <AS#> <ip add +mask > (optional)

# sh ip eigrp topology all-links
# sh ip eigrp topology < active / pending / zero-successors>
# sh ip eigrp traffic
# sh ip eigrp events (Shows the types of packets sent and received and
statistics on routing decisions.)
#debug ip eigrp
#debug ip eigrp fsm
#debug ip eigrp nei (Shows the hello packets sent and received to the neighbors)
#debug ip eigrp route (Shows dynamic changes made on the routing table process)
#debug ip eigrp summary (Shows a summary of the EIGRP activity)
#debug ip eigrp packet (Shows the packets sent and received by the router.
The packet types to be monitored can be selected.
Up to 11 types are available)
# no debug all / u all
Thanks & B.Regards

Ahmed Elhoussiny, CCIE # 21988 (R&S)
Network Consultant & Cisco Academy Instructor
'I can accept failure. Everyone fails at something.,But I can't accept not trying.'
' Every class i teach , i learn something new myself '
http://twitter.com/aelhoussiny
www.linkedin.com/in/aelhoussiny
CCNA4.com - Free CCNA Training & Resources

Eigrp Summary

Uploaded by

Copyright:

Available Formats

Eigrp Summary

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Eigrp Summary

Uploaded by

Copyright:

Available Formats

CCNA4.

com - Free CCNA Training & Resources

 Hybrid routing protocol (distance vector that has link-state protocol

 Use DUAL, first proposed by E. W. Dijkstra and C. S. Scholten, to perform

 Cisco Proprietary created in 1994.

 First released in IOS 9.21

 Uses IP protocol 88.

 Makes Automatic summarization on network Class boundary.

 Classless protocol (supports VLSM).

 Default composite metric of bandwidth and delay.

 Eigrp metric is the same as IGRP*256, It uses the smallest B.W,Reliablity,Load

 Sends non-periodic, partial, and bounded updates.

 By default, EIGRP uses no more than 50 percent of the bandwidth of a link.

 Uses DUAL for loop prevention, and generating Succ./Fesible Succ.

 Maximum paths for Load-balancing are 6 & default is 4 , maximum are 16 in

 By default, Equal-Metric load balancing. If Unequal-Metric load sharing is used

The composite metric for each EIGRP route is calculated as

IGRP metric = [k1*BWIGRP(min) + (k2* BWIGRP(min))/(256-LOAD) + k3*DLYIGRP(sum)]

If k5 is set to zero, the [k5/(RELIABILITY+k4)] term is not used.

IGRP metric = BWIGRP(min) + DLYIGRP(sum)

DLYIGRP(sum) = DLY(sum) /10

EIGRP has four components:

config)# router eigrp <AS#>

conf-router)# metric maximum-hop <#> (Up to 255, default =224)

conf-router)#distance eigrp <AS> <internal AD> <external AD>

conf-router)#maximum –paths <N> (Up to 6 Links for load sharing,

conf-router)#no auto-summary (disable automatic summ. To the class boundary)

config-if)# bandwidth < # in Kbps>

config-if)# ip hello-interval eigrp <AS#> < sec >

1-Define a key chain with a name.

2- Define the authentication key or keys on the key chain

3- Define the password of the key or keys.

4- Apply MD5 authentication on an interface (EIGRP only support MD5).

5- Apply authentication on an interface and specify the key chain to be used.

6- Optionally configure key management.

Here is the cmds :

config)# interface <int>

# debug eigrp packets

accept life time = accept this key

# sh ip eigrp topology <AS#> <ip add +mask > (optional)

Thanks & B.Regards

CCNA4.com - Free CCNA Training & Resources

You might also like

IGRP metric = [k1BWIGRP(min) + (k2 BWIGRP(min))/(256-LOAD) + k3*DLYIGRP(sum)]