Summary of the regs interface’s registers

ALERT_TEST

Alert Test Register

• Offset: 0x0
• Reset default: 0x0
• Reset mask: 0x1

Fields

{"reg": [{"name": "fatal_error", "bits": 1, "attr": ["wo"], "rotate": -90}, {"bits": 31}], "config": {"lanes": 1, "fontsize": 10, "vspace": 130}}

STATUS

SRAM status register.

• Offset: 0x4
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "BUS_INTEG_ERROR", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "INIT_ERROR", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "ESCALATED", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "SCR_KEY_VALID", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "SCR_KEY_SEED_VALID", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "INIT_DONE", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "READBACK_ERROR", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "SRAM_ALERT", "bits": 1, "attr": ["ro"], "rotate": -90}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 200}}

STATUS . SRAM_ALERT

This bit is set to 1 if a multi bit encoding error has been detected inside the RAM modules. This error triggers a fatal_error alert. This condition is terminal.

STATUS . READBACK_ERROR

This bit is set to 1 if a SRAM readback check failed. This error triggers a fatal_error alert. This condition is terminal.

STATUS . INIT_DONE

Set to 1 if the hardware initialization triggered via CTRL.INIT has completed.

STATUS . SCR_KEY_SEED_VALID

Set to 1 if the scrambling key has been derived from a valid key seed in OTP. If STATUS.SCR_KEY_VALID is set to 1, STATUS.SCR_KEY_SEED_VALID should be 1 except for cases where the scrambling key seeds have not yet been provisioned to OTP. In such a case, the scrambling key is still ephemeral (i.e., it is derived using entropy from CSRNG), but a default all-zero value is used as the key seed.

STATUS . SCR_KEY_VALID

Set to 1 if a new scrambling key has been successfully obtained from OTP. Note that if this is set to 0, the SRAM contents are still scrambled, but a default all-zero key and nonce are used to do so.

STATUS . ESCALATED

Set to 1 if the sram controller has received an escalate request. If this is set to 1, the scrambling keys have been reset to the default values and all subsequent memory requests will be blocked. This condition is terminal.

STATUS . INIT_ERROR

This bit is set to 1 if a the initialization counter has reached an invalid state. This error triggers a fatal_error alert. This condition is terminal.

STATUS . BUS_INTEG_ERROR

This bit is set to 1 if a fatal bus integrity fault is detected. This error triggers a fatal_error alert. This condition is terminal.

EXEC_REGWEN

Lock register for execution enable register.

• Offset: 0x8
• Reset default: 0x1
• Reset mask: 0x1

Fields

{"reg": [{"name": "EXEC_REGWEN", "bits": 1, "attr": ["rw0c"], "rotate": -90}, {"bits": 31}], "config": {"lanes": 1, "fontsize": 10, "vspace": 130}}

EXEC

Sram execution enable.

• Offset: 0xc
• Reset default: 0x9
• Reset mask: 0xf
• Register enable: EXEC_REGWEN

Fields

{"reg": [{"name": "EN", "bits": 4, "attr": ["rw"], "rotate": 0}, {"bits": 28}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

EXEC . EN

Write kMultiBitBool4True to this field to enable execution from SRAM. Note that this register only takes effect if the EN_SRAM_IFETCH switch in the OTP HW_CFG1 partition is set to kMultiBitBool8True. Otherwise execution from SRAM cannot be enabled via this register.

CTRL_REGWEN

Lock register for control register.

• Offset: 0x10
• Reset default: 0x1
• Reset mask: 0x1

Fields

{"reg": [{"name": "CTRL_REGWEN", "bits": 1, "attr": ["rw0c"], "rotate": -90}, {"bits": 31}], "config": {"lanes": 1, "fontsize": 10, "vspace": 130}}

CTRL

SRAM ctrl register.

• Offset: 0x14
• Reset default: 0x0
• Reset mask: 0x3
• Register enable: CTRL_REGWEN

Fields

{"reg": [{"name": "RENEW_SCR_KEY", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "INIT", "bits": 1, "attr": ["wo"], "rotate": -90}, {"bits": 30}], "config": {"lanes": 1, "fontsize": 10, "vspace": 150}}

CTRL . INIT

Write 1 to request memory init. The init mechanism uses an LFSR that is seeded with a part of the nonce supplied when requesting a scrambling key. Once seeded, the memory is initialized with pseudo-random data pulled from the LFSR. Note that CTRL.RENEW_SCR_KEY takes priority when writing 1 to both CTRL.RENEW_SCR_KEY and CTRL.INIT with the same write transaction. This means that the key request will complete first, followed by SRAM initialization. Note that writing 1 to this register while an init request is already pending has no effect.

CTRL . RENEW_SCR_KEY

Write 1 to request a new scrambling key from OTP. After writing to this register, SRAM transactions will be blocked until STATUS.SCR_KEY_VALID has been set to 1. If STATUS.SCR_KEY_VALID was already 1 before triggering a key renewal, hardware will automatically clear that status bit such that software can poll its status. Note that requesting a new scrambling key takes ~200 OTP cycles, which translates to ~800 CPU cycles (OTP runs at 24MHz, CPU runs at 100MHz). Note that writing 1 to this register while a key request or a memory initialization request is already pending has no effect.

SCR_KEY_ROTATED

Clearable SRAM key request status.

• Offset: 0x18
• Reset default: 0x9
• Reset mask: 0xf

Fields

{"reg": [{"name": "SUCCESS", "bits": 4, "attr": ["rw1c"], "rotate": -90}, {"bits": 28}], "config": {"lanes": 1, "fontsize": 10, "vspace": 90}}

SCR_KEY_ROTATED . SUCCESS

This status register is similar to SCR_KEY_VALID with the difference that the status is multibit encoded, SW clearable and sticky (i.e., HW does not auto-clear the register except during escalation). That way, SW can use this for a hardened acknowledgement mechanism where it clears the register before requesting a key.

kMultiBitBool4True indicates that a valid scrambling key has been obtained from OTP. Write kMultiBitBool4True to clear.

READBACK_REGWEN

Lock register for readback enable register.

• Offset: 0x1c
• Reset default: 0x1
• Reset mask: 0x1

Fields

{"reg": [{"name": "READBACK_REGWEN", "bits": 1, "attr": ["rw0c"], "rotate": -90}, {"bits": 31}], "config": {"lanes": 1, "fontsize": 10, "vspace": 170}}

READBACK

readback enable.

• Offset: 0x20
• Reset default: 0x9
• Reset mask: 0xf
• Register enable: READBACK_REGWEN

Fields

{"reg": [{"name": "EN", "bits": 4, "attr": ["rw"], "rotate": 0}, {"bits": 28}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

READBACK . EN

Write kMultiBitBool4True to this field to enable the readback security feature for the SRAM. A readback of each memory write or read request will be performed and a comparison happens. Any other value than kMultiBitBool4False written to this field is interpreted as kMultiBitBool4True.

This interface does not expose any registers.