Man SG TwinStarV27 27op A

TWINSTAR™ SLANT (AH-1S227) OPERATOR INSTRUCTIONS
Slant Cabinet Setup
5 October 2017 1486388 [A]
ORIGINAL INSTRUCTIONS: ALL NON-ENGLISH EDITIONS OF THIS DOCUMENT ARE TRANSLATIONS OF THE ORIGINAL INSTRUCTIONS.
CONFIDENTIAL
© 2017 Scientific Games Corporation, All Rights Reserved. Unauthorized distribution prohibited. Confidential
Scientific Games Corporation
6601 Bermuda Road
Las Vegas, NV 89119, USA
1 855 777 7435 (Toll Free)
1 702 897 7150
http://www.scientificgames.com
This document (“Document”) has been provided to you by Scientific Games Corporation or one or more of its directly or indirectly wholly
owned companies (collectively, “Scientific Games”). This Document contains a variety of: (a) materials and other items relating to products or
services of Scientific Games or its licensors or other third parties, including layout, information, text and scripts, data, files, images,
photographs, pictures, artwork, designs, graphics, logos, drawings, charts, button icons, instructions, illustrations, advertising copy,
technology, interactive features, “look and feel,” and the compilation, assembly and arrangement of the materials of the Document, and
copyrightable material; (b) service marks, trademarks, logos, trade names and trade identities of Scientific Games or its licensors or third
parties, when applicable; and (c) other forms of intellectual property (all of the foregoing in (a), (b) and (c), collectively, “Content”). This
Document and the Content are owned or controlled by Scientific Games or its licensors or third parties, when applicable. All right, title, and
interest in and to the Content is the property of Scientific Games or its licensors, when applicable, and is protected by the intellectual
property laws of the United States and elsewhere to the fullest extent possible. All ® notices signify marks registered in the United States by
Scientific Games or its licensors, when applicable. Scientific Games grants the intended recipient a limited, non-exclusive, revocable,
non-assignable, personal, and non-transferable license to view and/or print one copy of the Content, but Scientific Games or its licensors, as
the case may be, retain ownership of such Content. The foregoing limited license does not provide the intended recipient with any ownership
of, or any other intellectual property interest in, any Content and this license may be immediately suspended or terminated for any reason, by
Scientific Games in its sole discretion, and without advance notice or liability.
This Document has been provided to you solely for use in operating the product described herein. The specifications and information
contained in this documentation are subject to change without notice. All statements, information, illustrations, specifications and
recommendations in this documentation are believed to be accurate, but are provided without warranty of any kind, express or implied. The
product information referenced in this Document is being provided by Scientific Games as is.
© 2017 Scientific Games Corporation, All Rights Reserved. Unauthorized distribution prohibited. CONFIDENTIAL
TwinStar™ Slant (AH-1S227) Operator Instructions 1486388 [A]
2
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Reference Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Preventing Injury and Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmental Protection and Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating Environment (Recommended) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dimensions for Cabinet with Topper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dimensions for Cabinet without Topper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unpacking and Inspecting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lock and Cam Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Door and Lock Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Opening and Closing Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Accessing the Middle Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Accessing the Upper Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Accessing the Upper Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Accessing the Lower Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessing Under the Footrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessing the Deck Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessing the Security Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removing and Installing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Removing the Upper Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing the Upper Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Removing the MPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installing the MPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Operational Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Attendant Pays and Canceling Credits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Collecting Bills from the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Refilling the Printer Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 3 Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power Backplane Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Contents 3
Signal Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Lighting Control Unit (LCU) Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cabinet Signal Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter 4 Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Contents 4
Preface
This preface includes the following topics:
 Reference Information on page 5
 Contact Information on page 5
 Preventing Injury and Damage on page 5
 Environmental Protection and Recycling on page 5
Reference Information
Revocation Bulletins, Service Manuals, and other documents are available online at
https://www.SGgaming.com/members/login. To request a login and password, select Request New Login.
The following documents provide additional information:
 Service Manual and User Guide 1458262: ArgOS 2.X Operating System
Contact Information
Region Telephone Email
Americas + 1 877 748 3387 [email protected]
Asia Macau 853 625 22559 [email protected]
Singapore 65 8522 7465
Australia/New Zealand Australia 1 800 837 668 [email protected]
New Zealand 0800 476 321
Europe/Middle East/Africa (EMEA) +34 93 594 87 20 [email protected]
Preventing Injury and Damage

 Preventing Shock: Always remove power from the machine before starting any service tasks.
 Preventing ESD: Always use appropriate ESD mitigation procedures.
 Replacing the Power Cord: If the Power Cord is damaged, it must be replaced by the manufacturer (Scientific
Games Corporation), its service agent, or similarly qualified persons to avoid a hazard.
 Properly Secure and Vent All Equipment: Before starting any service tasks, the cabinet, top or accessory box,
and machine must be correctly secured and installed, with adequate ventilation, as described in the
corresponding product manual or guide to avoid injury and equipment damage.
 Ladder Safety: Follow all company mandated ladder safety procedures. Do not exceed the maximum load
rating of a ladder. Be aware of the ladder load rating and of the weight it is supporting, including the weight of
any tools or equipment.
Environmental Protection and Recycling

This product bears a recycling mark in accordance with the Waste from Electrical Electronic
Equipment (WEEE) European Commission Directive 2012/19/EU. This mark indicates that the
product should be deposited at an appropriate facility to enable recovery and recycling in
accordance with all applicable laws. To identify an environmentally sound disposal method for
this product or its component parts, please contact the responsible government authority in
your area. For information on available product take-back programs, see our websites
https://www.sggaming.com/Customer-Center/Games-Support/WEEE-Directive or
http://www.scientificgames.com.
Preface 5
Chapter 1 Overview
This chapter includes the following topics:
 Prerequisites on page 6
 Electrical Specifications on page 7
 Physical Specifications on page 7
 Operating Environment (Recommended) on page 7
 Dimensions on page 8
This document provides operating instructions for the TwinStar™ Slant AH-1S227 (AH-1S227ST). Your machine displays
only the features supported by your software version, jurisdiction, and machine configuration. All features do not
display on every machine. If any feature does not apply to your machine, then go to the next section.
CAUTION
This document may describe procedures for equipment that do not apply to all
cabinet configurations, or that may require additional components. Each
regulatory jurisdiction may have controls, policies and, procedures that you must
follow. You are responsible for understanding and abiding by the rules that apply
in your environment.
Prerequisites
This installation may require the following additional items:
 Locks (quantity 5 to 9, depending on your machine configuration)
 Category 5 network cables (quantity and length depending on your machine configuration and your floor plan
layout)
 Tools for locks
 22 mm (7/8-inch), 11 mm (7/16-inch), and 10 mm (0.39-inch) socket or wrench
 Nut driver
 Needle nose pliers
 Phillips head screw driver
 Set of Allen wrenches
 Operating system software manual for your machine
Chapter 1 Overview 6
Electrical Specifications
Electrical Specifications
NOTE
Typical currents are provided for reference only. Actual current use will depend
upon machine configuration and addition of supplemental equipment such as,
but not limited to, the following: systems monitoring equipment, progressive
equipment, and service equipment.
Table 1 Electrical Specifications
Description Cabinet with Topper Cabinet without Topper
Cabinet Image
Line Voltage 120 VAC 120 VAC

Surge State Current 1.5 Amps at 120 VAC (0.75 Amps at 240 VAC) 1.1 Amps at 120 VAC (0.55 Amps at 240 VAC)
Operating State Current 1.6 Amps at 120 VAC (0.8 Amps at 240 VAC) 1.4 Amps at 120 VAC (0.7 Amps at 240 VAC)
Fuse Limited Rated Current 6.3 Amps at 120 VAC (3.15 Amps at 240 VAC) 6.3 Amps at 120 VAC (3.15 Amps at 240 VAC)
Heat Generated (BTU/HR) 622 545
Physical Specifications
Table 2 Physical Specifications
Weight
Weight (Un-crated including Flammable 164.66 kg (363 lbs) 153.77 kg (339 lbs)
Weight)
Flammable Weight 29.71 kg (65.5 lbs) 27.22 kg (60 lbs)
Dimensions
Width 71.36 cm (28.09-in.) 71.36 cm (28.09-in.)
Depth 73.32 cm (28.9-in.) 73.32 cm (28.9-in.)
Operating Environment (Recommended)

CAUTION
To prevent temperature and humidity related stress on the machine, operate the
machine within the recommended guidelines. Operating the machine outside the
recommended guidelines may increase the required maintenance.
Table 3 Operating Environment
Temperature Range 4-40 Degrees Celsius 4-40 Degrees Celsius
(39.2 - 104 Degrees Fahrenheit) (39.2 - 104 Degrees Fahrenheit)
Humidity (Maximum) 90% 90%
Dimensions
Dimensions
Dimensions for Cabinet with Topper

Figure 1 Front and Side Views for Cabinet with Topper
30.98 cm
(12.2 in.)
24.89 cm
(9.8 in.)
218.44 cm
(86.0 in.)
201.93 cm
(79.5 in.)
162.30 cm
(63.9 in.)
73.66 cm
(29.0 in.)
66.04 cm
71.36 cm (26.0 in.)
(28.09 in.)
73.32 cm
(28.9 in.)
Dimensions
Dimensions for Cabinet without Topper

Figure 2 Front and Side Views for Cabinet without Topper
24.89 cm
(9.8 in.)
177.80 cm
(70.0 in.)
73.66 cm
(29.0 in.)
66.04 cm
(26.0 in.)
73.32 cm
(28.9 in.)
Chapter 2 Instructions
 Unpacking and Inspecting the Machine on page 10
 Lock and Cam Specification on page 11
 Door and Lock Locations on page 12
 Opening and Closing Doors on page 13
 Removing and Installing Components on page 19
 Installing the Machine on page 25
 Operational Tasks on page 27
Unpacking and Inspecting the Machine

1 Remove any plastic packaging.
2 Verify that the serial numbers on the cabinet match with the shipping documents associated with the
installation.
CAUTION
All serial numbers must match the shipping documents that are associated with
the installation. Never remove serial numbers from any equipment
3 Inspect the cabinet for any shipping damage, such as dents or scratches.
4 Unpack and remove all loose parts from any boxes or bags containing cables, lock cams, and mounting
hardware.
5 Remove all plastic or paper packing materials from any interior assemblies, such as a printer.
6 Inspect the interior cables and ensure they are firmly connected.
7 Inspect the circuit board assemblies for loose connections.
NOTE
During shipping, cables may become disconnected and circuit boards may
become unseated. Ensure they are firmly attached before proceeding.
8 Locate and open the logic door.
9 Re-seat the flash media in the sockets if necessary.
10 If the machine is damaged or any parts are missing, then please contact your Distributor or Customer Service
Representative for Return Merchandise Authorization (RMA) information.
CAUTION
If a new machine is damaged and awaiting replacement parts, then do not
remove any existing parts from it for use in another machine.
Chapter 2 Instructions 10
Lock and Cam Specification
Lock and Cam Specification

Table 4 Lock and Cam Specifications
Lock Location Cam Cam Part
Illustration Number
Cam Middle Door Lock (Left Turn) 237627
Optional Middle Door Secondary Lock (Left Turn) 237904
Lower Door Lock (DROP) (Right Turn) 237511
Bill Acceptor Cash Box Access Door Lock (Right Turn) 200454
Optional Second Bill Acceptor Cash Box Access Door Lock (Right Turn) 200454
Flash Media Module (Right Turn) 200125
MPU Housing (Left Turn) 200454
NOTE
TIP: To avoid delays, purchase your machine locks well before your planned
installation date. Purchase several spare machine locks from your lock
manufacturer and keep them available. If necessary, use a 1.6 mm lock spacer
(200455) or a 28.6 mm spacer (202035-00003 and S-00231-984).
Door and Lock Locations
Door and Lock Locations

Figure 3 Door and Lock Locations
A G
F
B E
D
C
Table 5 Door and Lock Location Figure Legend

Callout Description
A Audit Key Switch
B Deck Door (not shown)
C Lower Door Lock
D Lower Door
E Middle Door
F Middle Door Lock
G Upper Door Lock
H Upper Door
Opening and Closing Doors

Use the following instructions to ensure safe and correct operation of door equipment:
 Secure doors with locks installed according to instructions from your lock manufacturer.
 Inspect door latches, brackets, pins, hinges, and gas springs (if applicable) for wear or damage, and replace, if
necessary.
 When opening and closing doors, always hold or support doors and use the provided latch release
mechanisms, handles, or knobs.
 When closing doors, always ensure the door frame areas are free of foreign objects and the door latches and
closes securely. Do not apply excessive force.
 To avoid damaging latches when closing, always use the door handles or knobs to hold latches in the open
position, close the door, and then release the handle or knob gently. (For applicable doors.)
Accessing the Middle Door

Use the following instructions to open the middle door:
1 To open the middle door, turn the bottom right lock of the door counterclockwise and lower the door.
Figure 4 Bottom Right Lock Location
2 To close the middle door, raise the middle door until the door connects to the cabinet frame securely.
Accessing the Upper Door

Use the following instructions to access the upper door:
1 To open the upper door, turn the upper right lock of the middle door clockwise, then open the upper door from
right to left.
Figure 5 Upper Right Lock Location
2 Close the upper door from left to right, then press the right side of the monitor until the door connects to the
cabinet frame securely.
Accessing the Upper Monitor

Use the following instructions to access the upper monitor:
1 Before accessing the upper monitor, ensure that the upper door is securely closed.
2 Open the middle door. See Accessing the Middle Door on page 13.
3 Locate the yellow release handle on the far right and pull firmly towards yourself.
Figure 6 Release Handle Location
4 Pull the upper monitor towards yourself until it latches.
Figure 7 Upper Monitor
5 To close the upper monitor main door, hold the monitor on the left side and pull the lock pin on the right side of
the latch assembly to release the monitor.
Figure 8 Lock Pin Location
6 Lower the monitor until it connects to the cabinet frame.
Accessing the Lower Door

Use the following instructions to access the lower door:
1 To open the lower door, turn the key in the lower door lock clockwise and lift the door. Hinges hold the door
open.
2 To close the lower door, press down on the door until it connects to the cabinet frame, then lift and push to
close the door.
3 To lock the door, turn the key in the lower door lock counterclockwise.
Figure 9 Accessing the Lower Door
Accessing Under the Footrest

Use the following instructions to access the area under the footrest:
1 To open the footrest, lift it using the provided finger reliefs.
Figure 10 Footrest Access Point Detail
2 To close the footrest, push down until it connects to the cabinet securely.
Accessing the Deck Door

Use the following instructions to access the deck door:
CAUTION
The deck door is not attached to the cabinet. To prevent injury or damage, hold the
center of the security panel firmly.
1 To open the deck door, unfasten two screws located under the iDeck using a Phillips head screw driver and save
the screws for future use.
Figure 11 Opening the Deck Door
2 To close the deck door, align the holes of the deck door and the cabinet.
Figure 12 Closing the Deck Door
3 Secure the deck door to the cabinet with two screws previously removed.
Accessing the Security Panel

Use the following instructions to access the security panel:
1 To open the security panel, open the middle door. See “Accessing the Middle Door” on page 13.
2 Locate the security panel latch behind the deck.
Figure 13 Security Panel Latch Detail
CAUTION
This door opens downward. To prevent injury or damage, hold the door firmly.
3 Slide the latch to the right and lower the security panel.
Figure 14 Security Panel Door Open
4 To close the security panel, route any cables where they will not be pinched, and insert the security panel up
into the cabinet from under the button deck area until the door connects to the cabinet frame securely.
CAUTION
To ensure that wires and cables are not pinched, abraded, or otherwise damaged,
use care when inserting and removing doors.
Removing and Installing Components
Removing the Upper Door

Use the following instructions to remove the upper door.
CAUTION
The door is heavy. To prevent injury or damage, enlist the aid of another technician
during removal.
1 Open the upper door. See Accessing the Upper Door on page 13.
2 Disconnect all cables from the monitor assembly.
Figure 15 Monitor Cable Connections
CAUTION
To ensure wires and cables are not pinched, abraded, or otherwise damaged, use
care when inserting and removing doors.
3 Use a Phillips head screw driver to remove the ground cable from the monitor assembly.
Figure 16 Ground Cable Connection
4 Use a Phillips head screw driver to unfasten two screws from the bracket at the top right of the back of the
monitor assembly. Reserve the screws for future use.
Figure 17 Monitor Bracket Screws
5 Use an Allen wrench to unfasten the lower hinge of the monitor from the cabinet.
Figure 18 Monitor Lower Hinge
6 Use an Allen wrench to unfasten the upper hinge of the monitor from the cabinet.
Figure 19 Upper Monitor Hinge
Installing the Upper Door

Use the following instructions to install the upper door:
CAUTION
The door is heavy. To prevent injury or damage, enlist the aid of another technician
during installation.
1 Use an Allen wrench to fasten the upper hinge of the monitor to the cabinet.
Figure 20 Upper Monitor Hinge
2 Use an Allen wrench to fasten the lower hinge of the monitor to the cabinet.
Figure 21 Monitor Lower Hinge
3 Use a Phillips head screw driver to fasten the bracket to the top right of the back of the monitor assembly.
Figure 22 Monitor Bracket Screws
4 Use a Phillips head screw driver to attach the ground cable to the monitor assembly.
Figure 23 Ground Cable Connection
5 Reconnect all cables previously disconnected from the monitor assembly.
Figure 24 Monitor Cable Connections
CAUTION
To ensure wires and cables are not pinched, abraded, or otherwise damaged, use
care when inserting and removing doors.
Removing the MPU

Use the following instructions to remove the MPU
1 Open the upper door. See Accessing the Upper Door on page 13.
2 Locate the MPU on the left side of the cabinet.
3 Turn the thumbscrew counterclockwise to unfasten the MPU cover plate and pull the plate towards the center
of the cabinet.
Figure 25 MPU Thumbscrew Location
4 Lift the MPU by the handle to release, lean it forward, then lift again to remove the MPU.
Figure 26 MPU Cover Plate Open
Installing the MPU

Use the following instructions to install the MPU:
1 Open the upper door and open the MPU cover plate. See Opening and Closing Doors on page 13.
2 Insert the MPU into the provided MPU bracket by lowering, leaning it forward, then lowering into the
connectors.
Figure 27 MPU Cover Plate Open
3 Close the MPU cover plate and secure by turning the thumbscrew clockwise.
Figure 28 MPU Thumbscrew Location
Installing the Machine

Use the following instructions to install the machine:
1 Ensure the new location has appropriate power and network cabling installed.
NOTE
Changes in floor configuration may require reconfiguring and rerunning of new
power and CAT-5 cables.
2 Use the instructions provided by your lock manufacturer to install locks in appropriate areas. (Machine
configurations may vary.)
• button deck
• external bill acceptor door
• bill acceptor cash box door
• bill acceptor cash box access door
• lower door
• quick-drop door (if selected)
• logic door (CPU and flash media card)
3 Move the machine to the desired location using a lifting or moving device, such as a hand truck.
CAUTION
The machines are heavy. To prevent injuries and damage always wear a back
brace, work with a partner, and do not use the tower light to move the machine. To
move the machine easily over a carpeted area, use a hand truck with solid tires, not
air-filled.
4 Place the machine at the desired location.
CAUTION
Ensure the back and sides of the cabinet are not exposed or accessible by players.
• Do not place the machine on any wires or cables.
• For two or more cabinets, place cabinets side-by-side or back-to-back and, if applicable, secure each
cabinet to an adjacent cabinet.
• Example – For one cabinet, install against a wall or in a corner.
Figure 29 Single Cabinet Example
• Example – For a single line of cabinets, install against a wall.
Figure 30 Single Line of Cabinets Example
• Example – For multiple, freestanding, even numbers of cabinets not positioned against a wall, install
back-to-back.
5 Securely fasten the machine to the stand and, if applicable, adjacent cabinet or wall.
6 Connect and route the power and network cables where they will not be pinched, abraded, or otherwise
damaged.
• Route the power cable through a cut-out in the base, at the left, right, or back of the machine as
appropriate for your floor plan layout.
• Open the cabinet door and verify that the power and network cables are not pinched under the machine
or any neighboring machines.
7 Press the power switches to supply power to the machine.
• Cabinet Power Switch – supplies power only to the cabinet components, not including the MPU assembly
• Main Power Switch – supplies power to the entire cabinet and MPU assembly
Figure 31 Cabinet and Main Power Switches
8 Set up and configure the software.
NOTE
For software setup and configuration information, see your ALPHA Game
Platform™ Software Setup Field Guide for machine operating system software
version.
Operational Tasks
Operational Tasks
Attendant Pays and Canceling Credits

Use the following instructions to release lockups:
NOTE
For more information about event or error messages and solutions, see your
operating system manual.
Messages similar to the following require an Attendant to release the lockup by turning a key in the audit key switch:
 Jackpot Handpay Pending
 Cashout Handpay
 Pay Win Handpay
1 Pay the player.
2 Turn the audit key switch to reset the EGM.
Figure 32 Turning the Audit Key Switch
Operational Tasks
Collecting Bills from the Machine

Use the following instructions to collect bills from the machine:
NOTE
Bill acceptor cash box collection procedures depend upon the machine model
specification, added equipment and the jurisdiction. Note that bill acceptor cash
boxes may vary depending upon the manufacturer and may include a cash box
release mechanism.
CAUTION
Complete your site’s procedures for accessing the machine.
1 Open the middle door. See “Opening and Closing Doors” on page 13.
2 Unlock and open the bill acceptor cash box door.
Figure 33 Unlocking and Opening the Bill Acceptor Cash Box Door
3 Remove the bill acceptor cash box from the machine.
Figure 34 Removing the Cash Box
4 Insert an empty bill acceptor cash box.

5 Close the bill acceptor cash box door and lock it.
6 Close the middle door.
Operational Tasks
Refilling the Printer Paper

Use the following instructions to refill the printer paper:
NOTE
Printer paper refill procedures depend upon the machine model specification,
added equipment, and the jurisdiction.
CAUTION
Complete your site’s procedures for accessing the machine. Obtain appropriate
coupon paper and ensure the coupon paper matches the machine’s coupon
printer size and capacity.
1 Open the upper door. See Opening and Closing Doors on page 13.
2 Put the paper in the paper tray in the appropriate orientation.
3 Insert the paper into the printer mechanism and close the upper door.
Figure 35 Putting Paper into the Paper Tray
Chapter 3 Reference
 CPU on page 30
 Power Backplane Board on page 31
 Signal Backplane on page 33
 Lighting Control Unit (LCU) Board on page 35
 Cabinet Signal Cable on page 37
CPU
The following figure displays a sample CPU.
Figure 36 CPU-4.2.2.X (264020-E8870)
A B C D E F G
N M L K J I H
Table 6 Figure Legend

Callout Description
A Display Port Video Interface, Primary
B Display Port Video Interface, Secondary
C Display Port Video Interface, iDeck
D Display Port Video Interface, Topper
E Ethernet
F Ethernet
G Power
H Flash Media Sockets (Behind the door)
I USB Ports, Quantity: 2
J USB Ports, Quantity: 2
K VGA, Secondary
Chapter 3 Reference 30
Power Backplane Board
Table 6 Figure Legend

Callout Description
L VGA, Primary
M Touch Screen, Secondary
N Touch Screen, Primary

The following figure displays a sample power backplane board.
Figure 37 Power Backplane Board Components
J14 J12
J9
J13
J16 J11
P3
J15
P2 J10
P1
J18 J17
J8
J4 J6
J5
J1
J7
J2
L1
J3
Table 7 Connectors for Power Backplane Board, (PCA249016-0-0)

Connector Usage
J1 SURGE JUMPER Surge Jumper Connector
J2 SWITCH CONNECTOR —
J3 LED INDICATOR AND TEST POINT PCB LED Indicator Light and Test Point PCB Connector
J4 UNSWITCHED A/C Power Connector
J5 MPU POWER SWITCHED A/C MPU Power Connector
J6 SWITCHED A/C Switched A/C Power Connector
J7 SWITCHED A/C Switched A/C Power Connector
J8 A/C DISTRIBUTION A/C Power Distribution Connector
J9 MONITOR POWER Monitor Power Connector
J10 DECK POWER Deck Power Connector
J11 D/C POWER D/C Power Connector
J12 RCU POWER RCU Power Connector
J13 TO D/C POWER BULKHEAD D/C Power for the Bulkhead
J14 MPU BACKPLANE MPU Backplane Connector
J15 7-SEGMENT AND DISPLAY METER POWER AND PAYLINE 7 Segment Display Meter Power and Payline Power Connector
J16 COIN MECH AND HOPPER POWER Coin Acceptor and Hopper Connector
J17 SPARE D/C POWER Spare D/C Power Connector
J18 SPARE D/C POWER Spare D/C Power Connector
P1, P2, P3 POWER SUPPLY Power Supply Connectors
L1 INPUT POWER FILTER Power Connector
Signal Backplane
Signal Backplane
The following figure displays a sample signal backplane board.
Figure 38 Signal Backplane Board, (PCA235204-0-0)
J20
J3
J18
P1
J14
U1
J13
J12
J9
J15
J16
BH1
P2
J17
J7
J6
J4
J1
J5
Signal Backplane
Table 8 Connectors for Signal Backplane Board, (PCA235204-0-0)

Connector Usage
BH1 Battery for memory retention when the power is off
J1 SERVICE LIGHT Service Light Connector
J3 SYSTEMS Systems Connector
J4 POWER INTERFACE Power Backplane Connector
J5 ATTENDANT SWITCHES Attendant Switch
J6 COUNTERS Electro-mechanical Counter Connector
J7 TOWER Tower Light Connector
J9 COM5 —
J11 COM9 (For future use)
J12 COM8 GAT Communication Port Connector
J13 COM7 Host 2 (secondary SAS) Systems Cable Connector or Printer
J14 COM1 Host 1 (primary SAS) Systems Cable Connector
J15 TOP BOX COM6 Top Box Connector
J16 COIN/HOPPER I/O Coin Acceptor and Hopper Connector
J17 DECK BUTTONS Button Signal Connector
J18 BILL ACCEPTOR COM2 Bill Acceptor Connector and Printer or Card Reader Connector
CARD READER COM4
PRINTER COM3
P1 MPU Board Connector
P2 MPU Board Connector
U1 DOOR SWITCH INPUTS All Door Input Switch Connector
Lighting Control Unit (LCU) Board

The following figure displays a sample LCU board.
Figure 39 LCU Board, (PCA245961-0-0)
Port 7 Port 4
J2
Port 6
Port 3
Port 5
Port 2
SW1
Port 1
Port 0
Power
USB
Table 9 Components for Lighting Control Unit (LCU) Board, (PCA245961-0-0)

Component Typical Usage and Description
J2 Indicator light
Power Power cable connector
Port 0 Super candle tower light, 16-pin connector
Port 1 Super candle tower light, 16-pin connector
Port 2 Cabinet side lights or Pro Topper (Marquee with FPD monitor), if installed, 12-pin connector
Port 5 Coin tray light or other simple device
Port 6 Coin tray light or other simple device
Port 7 Bally logo light, red
SW1 DIP Switch for manually setting light colors
USB LCU to MPU communication cable connection
Table 10 LCU Board DIP Switch Settings

Color Red Green Blue Reserved
DIP Switch 1 2 3 4 5 6 7 8
0% off off off off off off off off
33% on off on off on off off off
66% off on off on off on off off
100% on on on on on on off off
Table 11 Lighting Control Unit (LCU) Diagnostics

Light Pattern Description
Each light fades from red to orange, yellow, green, blue, indigo, The machine is in diagnostic mode. Typically, the diagnostic
and violet, one at a time, starting from the device in Port 0 and mode displays upon powering on.
ending at Port 7.
Upon start up, the lights do not fade from red to orange, yellow, A device is disconnected or damaged. Connect or replace the
blue, green, indigo, and violet starting from the device in Port 0 affected item.
and ending at Port 7.
Upon start up, no lights blink. The machine software does not detect or recognize the LCU
board. Verify that the LCU firmware is correct. Replace, if
necessary.
After initial start up and successfully passing the diagnostic A previously working and connected device has become
mode period, no lights blink. disconnected or damaged. Replace the affected item.
All of the lights blink continuously. A device is disconnected or damaged. Connect or replace the
affected item.
Some lights blink red, blue, and green. Or, some lights blink blue, The devices displaying this pattern are connected and
red, and green. undamaged. The devices that do not blink or blink another
pattern are damaged or the LCU does not contain firmware to
support the device. Replace the affected item or firmware.
Violet and green lights blink one, two, three, or four times. Or, A device is damaged or the LCU does not contain firmware to
green lights blink one, two, three, or four times. support the device. Replace the affected item or firmware.
The LED color or intensity is incorrect. A connector is loose or disconnected. Firmly connect the
affected item.
Table 12 LCU Board LED Indicator Light (D2)

Indicator Button Deck State Description
Off Off-line One of the following error conditions may exist: the power is off; the power
cable is unplugged; a firmware error exists; a hardware error exists; or the LCU is
held in reset by software, not yet loaded, or no Operating System software is
installed.
On Off-line The power is on and the firmware is loaded. If the green LED indicator light is
(Solid, without solid for 1.5 to 2 seconds and then briefly blinks off, then a reset may be
blinking) occurring and one of the following error conditions may exist: a hardware error
condition exists; incorrect firmware; a cable problem; or a defective LCU.
Two Blinks Off-line/No Tilts The machine communicates with the deck gadget. The operating system has
acquired the deck gadget, however, the deck gadget is unavailable.
One Blink On-line/No Tilts The machine communicates with the LCU. No errors exist.
Three Blinks On-line/Tilted One of the following error conditions may exist: a hardware error condition
exists or an SPI Error (Serial Protocol Interface Error) may exist.
Four Blinks Off-line/Tilted One of the following error conditions may exist: a hardware error condition
exists or an SPI Error (Serial Protocol Interface Error) may exist.
NOTE: A blink is a brief period where the indicator light is on. The indicator light continues to blink at 2 to 3 second intervals until the
error is corrected.
Cabinet Signal Cable

The following figure displays a sample cabinet signal cable.
NOTE
This cable includes wiring for some systems connections. If your system requires a
customized cable, then use the following diagram to identify and disconnect the
appropriate systems connectors.
Figure 40 Cabinet Signal Cable (251896-00-0) – Systems Interconnect Segment with Pin-Out View
INTERCONNECT
SYSTEMS
CON15
AE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
WT/GN-2
RD/WT-1
GY/GN-2
GY/GN-3
BL/WT-1
WT/BL-1
GY/BL-1
OR/WT
OR/GY
GN/GY
YE/WT
YE/GY
GN-1
VT
BL
WT/RD
MONITOR/MIDDLE DOOR SW
CASHBOX PRESENT (NO)

CASHBOX DOOR (NO)
LOGIC DOOR COMMON

LOGIC DOOR N.O.
LOGIC DOOR N.C.
BELLY DOOR SW
5V SENSE
GND
GND
GND
GND
GND
TX
RX
2 2
COM-1 OR/GY
4 4
N/C-1 OR/WT
BELLY DOOR SW
6 6
N/O-1
5 5
N/O-2
3 3
N/C-2
1 1
AM
COM-2
WT/GN-2
RD/WT-1
GY/GN-2
GY/GN-3
BL/WT-1
WT/BL-1
2
GY/BL-1
2
YE/GY
GN/GY
COM-1
GN-1
VT
BL
4 4
N/C-1 YE/WT
MAIN DOOR SW
6 6
AK
N/O-1
AJ
1
3
5
1
3
5
1
2
3
4
5
1
2
3
1
2
3
5
G
5
F
N/O-2
COM
COM
N/O
N/O
N/C
N/C
3 3
N/C-2
J27 - 5V SENSE
SYSTEM - MPU
LOGIC DOOR
1 1
BACKPLANE
BACKPLANE
COM-2
AL
COM 1 -
SYSTEM - STACKER PRESENT SW
SYSTEM - BV DOOR SW
Table 13 Cabinet Signal Cable – Systems Interconnect Pin-Outs

Pin Color Description
1 Yellow/Grey Ground
2 Yellow/White Monitor/Middle Door Switch
3 Grey/Green-2 Ground
4 Red/White-1 Cash Box Door (NO)
5 Grey/Green-3 Ground
6 Blue/White-1 Cash Box Present (NO)
7 Green-1 Transmit
8 Orange/Grey Ground
9 White/Green-2 Receive
10 Orange/White Belly Door Switch
11 Green/Grey Ground
12 Violet 5 Volt Sense
13 White/Blue-1 Logic Door N.O.
14 Blue Logic Door N.C.
15 Grey/Blue-1 Logic Door Common
Chapter 4 Spare Parts
 Spare Parts on page 39
Spare Parts
The following table provides spare part information:
Table 14 Spare Parts
Part Number Description Number of Machines
1-25 26-99 100+
212385 Universal Power Supply, 5/12/24V 2 4 8
237761 iDeck™ Assembly 1 3 6
264020-E8870 IMPU Assembly ALPHA 2.4™, AMD, ARGOS, E8870 2 4 6
PCA212319-0-0 Power Backplane Board ALPHA 2™ 1 2 4
PCA235204-0-0 Signal Backplane Board 1 2 4
Chapter 4 Spare Parts 39

Man SG TwinStarV27 27op A

Uploaded by

Copyright:

Available Formats

Man SG TwinStarV27 27op A

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Man SG TwinStarV27 27op A

Uploaded by

Copyright:

Available Formats

TWINSTAR™ SLANT (AH-1S227) OPERATOR INSTRUCTIONS

Slant Cabinet Setup

5 October 2017 1486388 [A]

Chapter 4 Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Preventing Injury and Damage

Environmental Protection and Recycling

Line Voltage 120 VAC 120 VAC

Operating Environment (Recommended)

Dimensions for Cabinet with Topper

Dimensions for Cabinet without Topper

Unpacking and Inspecting the Machine

Lock and Cam Specification

Optional Middle Door Secondary Lock (Left Turn) 237904

Lower Door Lock (DROP) (Right Turn) 237511

Flash Media Module (Right Turn) 200125

MPU Housing (Left Turn) 200454

Door and Lock Locations

Table 5 Door and Lock Location Figure Legend

Opening and Closing Doors

Accessing the Middle Door

Figure 4 Bottom Right Lock Location

Accessing the Upper Door

Figure 5 Upper Right Lock Location

Accessing the Upper Monitor

Figure 6 Release Handle Location

4 Pull the upper monitor towards yourself until it latches.

Figure 7 Upper Monitor

Figure 8 Lock Pin Location

6 Lower the monitor until it connects to the cabinet frame.

Accessing the Lower Door

Figure 9 Accessing the Lower Door

Accessing Under the Footrest

Figure 10 Footrest Access Point Detail

Accessing the Deck Door

Figure 11 Opening the Deck Door

Figure 12 Closing the Deck Door

Accessing the Security Panel

Figure 13 Security Panel Latch Detail

Figure 14 Security Panel Door Open

Removing and Installing Components

Removing the Upper Door

Figure 15 Monitor Cable Connections

Figure 16 Ground Cable Connection

Figure 17 Monitor Bracket Screws

Figure 18 Monitor Lower Hinge

Figure 19 Upper Monitor Hinge

Installing the Upper Door

Figure 20 Upper Monitor Hinge

Figure 21 Monitor Lower Hinge

Figure 22 Monitor Bracket Screws

Figure 23 Ground Cable Connection

5 Reconnect all cables previously disconnected from the monitor assembly.

Figure 24 Monitor Cable Connections

Removing the MPU

Figure 25 MPU Thumbscrew Location

Figure 26 MPU Cover Plate Open

Installing the MPU

Figure 27 MPU Cover Plate Open

Figure 28 MPU Thumbscrew Location