PERIPHERALS

MODULE 8

MK8-SVMOD-0001
PERIPHERALS Bally Gaming & Systems
©2001 BALLY GAMING AND SYSTEMS ALL RIGHTS RESERVED 6601 South Bermuda Road, Las Vegas, NV 89119
 For Customer Service and information:
+1-702-896-7772 Outside the U.S.
1-877-GO-BALLY (877) 46-22559 in the U.S. and Canada
896-7772 in Las Vegas
FAX: +1-702-896-7710
or visit our website at http://www.ballygaming.com
 Peripherals
Module 8
Peripherals Table of Contents

Coin Acceptors

Coin Mechanisms, Inc. Hoppers

CC-16 .................................................................... 8-5 Bally XS-1200 (AS-04787-SERIES) ........................ 8-12

CC-62 .................................................................... 8-5 Asahi Seiko 53 Slant Top (AS-03105-SERIES) ....... 8-14

CC-46 .................................................................... 8-5 Asahi Seiko 51 Bar Top (AS-03107-SERIES) ......... 8-18

MC-16, MC-62 ........................................................ 8-6

Coin Controls International Printers

Condor CN103 ........................................................ 8-6
Ithaca Series 70 Printer .......................................... 8-22
National Rejectors, Inc.
Vivo™ Seiko Printer ............................................... 8-26
NRI ......................................................................... 8-7

Bill Acceptors Accounting System Interface ...................... 8-30

JCM WBA-SS ........................................................ 8-8

JCM DBV-200 ........................................................ 8-10

Peripherals 8-3 © July 2001 Bally Gaming and Systems

Peripherals 8-4 © July 2001 Bally Gaming and Systems
 Peripherals
Coin Acceptors Coin Mechanisms CC-62
Power Requirements:
Voltage Range, 11.5 VDC to 12.5 VDC.

Wiring
Coin Mechanisms CC-16
The CC-62 Printed Circuit Board requires a 7-pin
Power Requirements: AMP right-angel locking connector interface.
Fixed VDC Models, 11.5 to 12.5 VDC.
1. Ground
2. Coin Sense
3. Error
General
4. Credit
Feed Rate, 7 Coins per second. 5. Key
Operating temperature recommended 0° to 6. 12 Volt
60° C. 7. Inhibit

Two Separate Outputs

Installing Sample Coin (CC-16, 62, & 46)
When the sensing coils sense a good coin, a pulse
Slide the sensor coil assembly to the right.
is sent out to the host machine. Following this, the
Replace the sample with the desired coin, and then
accept gate opens, and as the coin passes the LED
carefully release. When seated, the coin will rest
optics, a credit pulse is also sent out to the host ma-
parallel between the sensor coil assembly and the ribs
chine. Together these two pulses provide optimum
on the rail insert.
security against cheating. The host machine can be
configured to recognize a valid coin only when both
Wiring outputs have been detected.

The CC-16 Printed Circuit Board requires a 6 pin Coin Mechanisms CC-46
JST terminated interface. The following drawing
denotes the typical voltage line pinouts to the Printed Power Requirements:
Circuit Board.
Voltage Range, 11.5 to 15 VDC.
1. Inhibit input, 12 VDC models only.
Triac load, all others.
2. Sense output Wiring
3. 48 Volt
4. 24 Volt Mating connector is an AMP P/N 770602-7 (termi-
5. 12 Volt nals 770666-1or Molex P/N 22-01-3077. Series 2695
6. Ground Housing (terminals 2795 or 6459 Series).

1. Ground
Potentiometer Adjustment (CC-16 , 62, & 46) 2. Coin Sense
3. Error
Using a high quality slug, adjust the potentiom-
4. Credit
eter clockwise until the slug is rejected. Drop good 5. Key
coins through to ensure accurate acceptance. 6. +12 VDC

Peripherals 8-5 © July 2001 Bally Gaming and Systems

Coin Mechanisms CC-46 (cont.)

LED Feature
Coin Controls International
The CC-46 incorporates a bi-color (red and green) 2925 E Patrick Lane, Suite C,
LED on the front cover to indicate the operating status of Las Vegas, NV 89120
the mechanism. Green indicates it’s enabled. Red
indicates it’s disabled.
+1 702 739-8263

Condor CN103
General Features
Power Requirements:
Feed Rate: 8 Coins per second
Operating temperature: recommended 0° to 60°C. Voltage, 12 VDC to 32 VDC
Inhibit: Allows you to disable the device without
removing power from the unit.
Error: Alerts the machine of a malfunction or tampering General
of the device.
Credit Signal: This is an output which occurs for every Operating temperature: 0° to 60° C.
valid coin accepted through the device. Maintainable life of 20 million coins.
Sense Signal: This is an output which indicates a valid Coinage: Accepts coins within the diameter
coin has passed the sensor coils. range of .59-1.75" (15-44.5 mm) and the thickness
range of .059-.148" (1.5-3.75 mm).

Wiring
Connector 1 Pin 1 Inhibit all.
Pin 2 VACS +6V
Pin 3 +12 to 32 VDC
Micro Comparitor MC (Replacement for
Pin 4 +12 to 32 VDC
CC-16 and CC-62) Pin 5 +12 to 32 VDC
Pin 6 +0V

Connector 2 Pin 1 Accept (b) NPN

generation
Pin 2 VACS NPN
Pin 3 Alarm
Pin 4 Error

Connector 3 Serial Port

Connector 4 LCD display
CC-16 Emulation
Alarm
Open collector NPN is activated for 2 seconds
with inhibit all. This condition occurs when coins travel
in reverse, too slowly or block the opto beams. A
continuous yellow LED will result for the duration of the
alarm. During this time a pulse will appear on the error
pin.

CC-62 Emulation

Peripherals 8-6 © July 2001 Bally Gaming and Systems

 Peripherals
Condor CN103 (cont.) NRI National Rejectors, Inc. GmbH
Postfach 1461
D-2150 Buxtehude, Germany
Error
When a critical failure is detected at power up a
G-13, 0000 Coin Acceptor
500ms pulse will be given on the error line and will
repeat every 2 seconds. The LED will flash red and and
Power Requirements:
all coins will be inhibited. 12 VDC +3/-1 Volts tolerances

Teach and Run™ Programming General:

Follow these steps to program: Operating temperature 0° to 55° C.
Acceptance: Up to 6 different coins
Diameter: between .59” and 1.22” (15 and 31mm).
Thickness of coins: between .059” and .1” (l.5 and 2.6
mm)

Dimensions: Height: 4” (102 mm) Width: 3.5”

(89 mm) Depth: 2” (52 mm). Temperature range 0 C
up to +55 C

Coin inhibit
A common blocking line for all coins is available. Single
coin inhibit may be achieved by DIP switches on the G-
13.

Measuring principle
Three inductive sensors are arranged to detect material,
Security
thickness, diameter and embossing of coins as they
The acceptance window can be adjusted to pass. The passing coin activates the sensors,
increase fraud rejection or increase coin acceptance. providing different voltage measuring values. These
voltages are digitized and processed within the
microprocessor.

Programming of acceptor
A standard computer (IBM PC or compatible) allows
programming of the acceptor for any coin acceptance.
Programming means just the insertion of a coin which
should be accepted. Please refer to the document
“Use of program PROEMP.”
Wire Insertion View
Wiring
1. Ground 9 7 5 3 1
2. +12 VDC
10 8 6 4 2
3, 4, 7, 8, 9, 10. Coin Signals

Coin Signals: <.07 volts active low / 150 mA Open

collector NPN. I max = 150 mA, Umax = 35
volts. Time of pulses: 100 msec +/- 10%.
5. N.C.
6. Coin Inhibit

Peripherals 8-7 © July 2001 Bally Gaming and Systems

Bill Acceptors
North Las Vegas, NV 89031 Adjustable Bill Slot
Tel: +1 702 651 0000
Fax: +1 702 651 0003
Toll Free: 1-800-683-7248
JCM WBA-SS Bill Acceptor
Power Requirements:
Voltage Range, 95 to 135 VAC with power
supply 50 to 60 Hz, or 12 VDC max 20 VA.

The WBA-SS has the ability to read a wide range of bill

General
sizes. Four adjustment guides are available for bills
Magazine capacity 600 notes.
that are 65 mm to 80 mm wide.
Operating temperature recommended 0° to 45° C.

Collecting Bills

Collect bills by pressing the

release lever and pulling the
stacker box towards you.

Open the stacker box

cover and remove the
bills inside.

Component Identification

Bill Jams

Remove jammed bills from the bill head by moving the

release catches on
both sides of the
head towards you.
Open the acceptor
head to access the
jammed bill.

Peripherals 8-8 © July 2001 Bally Gaming and Systems

 Peripherals
JCM WBA-SS Bill Acceptor (cont.) WBA DIP Switch Selection

Remove jammed bills from

the transfer area by pulling
the access lever and
opening the top cover.

7 6 5 4 3 2 ON 1

Occasionally, a bill jams

near the inlet of the stacker
WBA DIP Switch Selection
box. Push the release lever
Switch ON OFF
of the stacker box and
remove it to access the 1 Reject $1 A cce p t $ 1
jammed bill. 2 Must be set to OFF OFF
3 Reject $5 A cce p t $ 5
4 Reject $10 A cce p t $ 1 0
5 Reject $20 A cce p t $ 2 0
6 Reject $50 A cce p t $ 5 0
7 Reject $100 Accept $100
8 Must be set to OFF OFF

Interface
The WBA-SS uses an ID-003 interface. The ID-003
interface is a bidirectional serial interface. The machine
is able to receive status reports from the WBA in
response to appropriate commands.

Peripherals 8-9 © July 2001 Bally Gaming and Systems

JCM DBV-200 DIP Switch Selection

Power Requirements Bank 1 Bank 2

+12VDC ON 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6

Wiring

D BV-200 Bank 1 Swi tch Selecti ons DBV-200 Bank 2 DIP Switch
DBV-200 Power DC Power Selections
Pi n # Signal Function Swi tch ON OFF
Switch ON OFF
Power 1 Reject $1 A cce p t $ 1 With Without
1 +12VDC 1
Supply Stacker Stacker
2 Reject $5 A cce p t $ 5
Power 2 Must be set to OFF OFF
2 Ground 3 Reject $10 A cce p t $ 1 0
Supply
2 Must be set to OFF OFF
3 NC Not Used 4 Reject $20 A cce p t $ 2 0
3 Must be set to OFF OFF
4 NC Not Used 5 Reject $50 A cce p t $ 5 0 4 Must be set to OFF OFF
5 NC Not Used 6 Reject $100 A cce p t $ 1 0 0 5 Must be set to OFF OFF
6 NC Not Used 7 Must be set to OFF OFF 6 Test Mode Normal

8 Must be set to OFF OFF

Interface 9 Must be set to OFF OFF
10 ID -045 ID -044
13 1

14 2

D BV-200 C onnecti on
Pi n # Si gnal Functi on
1 NC Not Used
2 NC Not Used
Indi cates that the vali dator i s i n
3 Busy
operati on
Soft Si gnal to clear ABN (abnormal) or
4
Reset STKF (stacker full) si gnal.
Termi nal to output communi cati on
5 D ata
message.
Si gnal allows to send any
6 C TS
communi cati on message.
7 Ground Ground
LE D
8 Power supply to dri ve LED
Power
9 NC Not Used
D i sable/- Vali dator can accept bi ll when Low,
10
Enable and can not accept when Hi gh
C onfi rms the start of communi cati on
11 RTS
message.
12 NC Not Used
13 NC Not Used
To be output when the vali dator i s i n
14 ABN
trouble, or when the stacker i s full.

Peripherals 8-10 © July 2001 Bally Gaming and Systems

 Peripherals
Hoppers
Bally Gaming and Systems products use the XS-
1200 Standard hopper. Some cabinet styles may use
hoppers manufacutred by Asahi Seiko, Inc.

Bally XS-1200 Standard Hopper

Asahi Seiko Hopper

Peripherals 8-11 ©July 2001 Bally Gaming and Systems

Bally Gaming XS-1200 Hopper (AS-04787-SERIES)

Peripherals 8-12 ©Julyl 2001 Bally Gaming and Systems

 Peripherals
Bally Gaming XS-1200 Hopper (AS-04787-SERIES) (cont.)

XS1200 Hopper Parts XS1200 Hopper With Mixer Parts

Item Part # Description Item Part # Description

1. P-09319-0512 Bracket, Outer Mounting 1. M-03082-001A Cover, Mixer Drive

2. P-09319-0511 Bracket, Inner Mounting 2. P-06264-0309 Handle
3. E-00733-0008 Optic Switch Assembly (2) TFPP-01032-1108 Screw
4. P-09319-0204 Bracket, Hopper Optic Guard, Outer 3. A-04349-0002 Bracket, Handle Mounting
5. E-00733-0008 Optic Switch Assembly (Single) NLS-00832-1112 Nut (2)
TFPP-00632-1114 Screw M-00319-0001 Stop Nut,Elastic (2)
6. P-09319-0203 Bracket, Hopper Optic Guard, Inner 4. P-09295-002D Baffle
7. P-00845 Wiper NLS-00832-112 Nut (2)
8. M-03073-0002 Wheel Housing, Hopper 5. S-00463-0053 Pin, Level Contact (Probe)
9. S-00231-0978 Spacer P-00800-0006 Washer (2)
10. M-03072-001B Drive Coupling, Pinwheel, Hopper NLS-00832-112 Nut (2)
11. S-02562-001A Roller Shaft 6. M-03048-0013 Coin Bowl, V7K
12. M-03009-A001 Roller (3) M-03048-0015 Coin Bowl, S6K
13. P-00842-011B Pin Wheel, 12 Pin (1.00Token) A-04394-0001 Grounding Stud
P-00482-010B Pin Wheel, 15 Pin (25¢) 7. AS-03368-0001 Assembly, Hopper Mixer Front/
P-00482-009B Pin Wheel, 16 Pin (5¢) Back Bracket
A-04308-001A Pin Wheel (5.00 Token) 8. M-03047-001A Mix Cylinder
14. P-00847-0024 Spacer, Shelf Wheel (5.00 Token) 9. M-03066-001A Roller (4)
15. P-00847 Shelf Wheel (25¢) .836” (21,23 P-02891-0006 Retainer Ring
mm) To .902” (22,91 mm) Diameter 10. S-02558-001A Shaft Roller (2)
X .062” (1,58 mm) Width 11. TFPP-00832-1924 Screw (6)
16. R-00526-0003 Agitator, 5¢ to $1 12. M-01348-0043 Thumbscrew
17. S-02569-0002 Cup, Washer, Pin Wheel Hold Down 13. SP-00200-0203 Spring (2)
18. S-00231-0825 Bushing, Agitator Mounting MSPT-01032-110B Nut (2)
19. P-09278-0004 Bracket, Counter Balance PW-00010-0012 Washer (2)
Adjustment, Super (mixer) Hopper 14. M-03074-001B Adaptor
P-09278-0005 Bracket, Counter Balance Adj. NLS-00832-0112 Nut (2)
P-09278-0008 Bracket, Counter Balance MSPT-01032-1108 Screw (3)
Adjustment, V72, NLS-01032-1112 Screw (3)
NLS-25020-1112 Nut 15. E-00119-0529 Mixer Cylinder Motor
MSOH-25020-1124 Screw 16. M-03069-001B Drive Gear Hopper
20. P-09277-001B Platform Bracket, (mixer) CPAO-01032-1804 Set Screw
21. P-09263-0005 Bracket, Hopper Mounting, Left 17. S-00231-0979 Spacer (4)
TFPP-00832-1106 Screw (6) S-00231-0978 Spacer (4)
22. P-09263-0006 Bracket. Hopper Mounting, Right NLS-00832-1112 Nut (2)
TFPP-01032-1106 Screw (6) 18. R-00111-0029 Rubber Grommet For Elec.Wire
23. AS-03356-0363 Hopper Control Board 19. P-09276-0002 Bracket, Drive Motor
24. P-06629-523A Bracket, PCB 20. MSPF-00832-1132 Screw
TFPP_00832-1104 Screw (4)
LSPP-00632-1108 Screw (4)
25. E-00119-0532 Motor, Pinwheel, Hi-Torque, 24RPM
26. P-00838-0011 Outlet Cover
P-00838-006B Outlet Cover, 5¢ & 25¢
P-00838-0009 Outlet Cover, 5¢-50¢
P-00838-007A Outlet Cover, 1.00 Token
P-00838-005A Outlet Cover, 5.00-100.00 Token
P-00838-0008 Outlet Cover, 5.00-100.00 Token Standard Hopper Coin Bowl
P-00838-0012 Outlet Cover, 5.00-100.00 Token
27. M-03068-0006 Knife, Coin, Up To 1.625”
(41,28mm) Diameter
Item Part # Description
M-03068-0007 Knife, Coin, Over 1.625” 1. P-09334-002B Handle
(41,28mm) Diameter 2. M-03048-0015 Coin Bowl, S6K, V8K
28. P-00839 Coin Deflector M-03048-0012 Coin Bowl, V7K
P-00839-0004 Coin Deflector, 1.00, 5.00, 25.00, M-03048-0017 Coin Bowl, V7 Casino
100.00 Token M-03048-0019 Coin bowl, V72
MSPF-0832-1106 Screw (2) S-00463-0053 Pin,Level Contact
29. P-09291-001B Spacer, Deflector Plate 3. P-09278-003A Retaining Bracket
M-01348-0043 Thumbscrew
4. SP-00200-203 Spring (2)

Peripherals 8-13 ©July 2001 Bally Gaming and Systems

Asahi Seiko Hoppers

Asahi Seiko USA, Inc.

6644 Paradise Road
Las Vegas, NV 89119
+1 702 260 6666

Asahi Seiko DH-750 Hopper, Model 53, Slant Top (AS-03105-SERIES)

DH-750 Model 53 Hopper Assembly

Peripherals 8-14 ©Julyl 2001 Bally Gaming and Systems

 Peripherals
Asahi Seiko Hoppers (cont.)

DH-750 Model 53, Slant Top Coin Hopper (cont.)

Item# Bally Part # Asahi Seiko Part # Description Item # Bally Part # Asahi Seiko Part # Description

1 DH7991M025001 PLATE, CHASSIS 32 ASH-05000-0001 B4025HXSS BOLT, M4x25, SS

2 DH7534M025002 FRAME, SIDE (R) 33 ASH-05000-0003 DH7001M005033 DISC, US 5¢
3 DH7534M025003 FRAME, SIDE (L) ASH-05000-0012 DH7001M025033 DISC. US 25¢
4 DH7534M025004 PLATE. BASE ASH-05000-0035 DH7001M10T033 DISC. $1 TOKEN

5 W4000SW99 WASHER, M4 SPLIT 34 ASH-05000-0013 DH7001M025034 SPRING, STIRRING

6 S4006RHSW SCREW, M4x6 W/SW 35 ASH-05000-0014 DH7001M025035 COVER, SPRING

7 ASH-05000-0005 DH7001M025007 PIN, MOTOR DRIVE 36 ASH-05000-0015 DH7001M025036 HOLDER. SPRING

8 ASH-05000-0040 DH7004M025008 MOTOR, 24VDC (DME44S7C-272) 37 ASH-05000-0016 DH7001M025037 SPRING, DISC

9 DH7001M025055 HANDLE 38 W4015FW10 WASHER, 4x15x1.0 FLAT

10 ASH-05000-0097 DH7101M025536 BRACKET, ESCALATOR MOUNTING 39 ASH-05000-0170 S4008LHSS SCREW. M4x8 TRUSS HEAD SS

11 ASH-05000-0168 DH7101M005530 GUIDE, TRANSITION (R), US 5¢ 40 ASH-05000-0108 S 4015C S 99 SCREW, M4x15 COUNTERSUNK

ASH-05000-0094 DH7101M025530 GUIDE, TRANSITION (R), US 25¢ 41 W4010FW10 WASHER, 4x10x1.0 FLAT

ASH-05000-0044 DH7101M10T530 GUIDE, TRANSITION (R). $1 TOKEN 42 ASH-05000-0029 DH7001M025073 SEPARATOR, COIN

12 ASH-05000-0169 DH7101M005531 GUIDE, TRANSITION (L). US 5¢ 43 ASH-05000-0030 DH7001M025074 RETAINER, SEPARATOR

ASH-05000-0095 DH7101M025531 GUIDE, TRANSITION (L), US 25¢ ASH-05000-0037 DH7001M10T074 RETAINER, SEPARATOR. $1 TOKEN

ASH-05000-0045 DH7101M10T531 GUIDE, TRANSITION (L), $1 TOKEN 44 S4010HXSS SCREW, M4x10 UPSET SF SS

13 ASH-05000-0077 DH7534M025529 COVER, TRANSITION (R) 45 S4015HXSS SCREW, M4x15 UPSET SF SS

14: ASH-05000-0096 DH7101M025534 PLATE, COIN SLIDE 46 S3010HXSS SCREW, M3x10 UPSET SF SS

15 ASH-05000-0043 DH7101M025015 ROLLER LEVER, ESCALATOR 47 S4012HXSS SCREW, M4x12 UPSET SF SS

16 ASH-05000-0006 DH7001M025016 SPRING. ROLLER LEVER 48 S4008HXSW SCREW, M4x8 UPSET SW SS

17 ASH-05000-0007 DH7001M025017 PIN, ROLLER LEVER 49 ASH-05000-0022 DH7001M025057 CAST FRAME

18 ASH-05000-0008 DH7001M025018 BEARING, ROLLER LEVER 50 DH7001M025058 06 BALL BEARING

19 ASH-05000-0112 W3000ER99 03 E-RING 51 DH7001M025059 RETAINER, BEARING

20 N4000HX99 NUT, M4 52 DH7001M025064 WASHER, ROLLER LEVER

21 B4012HX99 BOLT, M4x12 53 S4025LHSS SCREW, M4x25 LARGE HEAD SS

22 ASH-05000-0113 W3008FW08 WASHER, 3x8x0.8 FLAT 54 DH7001M005070 PLATE, ADJUSTING, US 5¢

23 ASH-05000-0106 S3010RH99 SCREW, M3x10 ASH-05000-0026 DH7001M025070 PLATE, ADJUSTING, US 25¢

24 ASH-05000-0086 N3000HX99 NUT, M3 DH7001M10T070 PLATE, ADJUSTING, $1 TOKEN

25 ASH-05000-0002 DH7001M005025 KNIFE, US 5¢ 55 DH7001M005071 RUBBER, JUMP, US 5¢

ASH-05000-0009 DH7001M025025 KNIFE, US 25¢ ASH-05000-0027 DH7001M025071 RUBBER, JUMP, US 25¢

ASH-05000-0034 DH7001M10T025 KNIFE, $1 TOKEN ASH-05000-0036 DH7001M10T071 RUBBER, JUMP. $1 TOKEN

26 ASH-05000-0010 DH7001M025026 BOSS. PLASTIC 56 ASH-05000-0004 DH7001M005072 COVER. JUMP, US 5¢

27 ASH-05000-0011 DH7001M025027 SCREW. BEVEL-HEADED ASH-05000-0028 DH7001M025072 COVER, JUMP

28 DH7101M10T538 COVER, TRANSITION (L) $1T 57 DH7514M025650 SHIM, TRANSITION (L) O.3t

29 ASH-05000-0099 DH7101M025538 COVER, TRANSITION (L) DH7514M10T650 SHIM, TRANSITION (L) 0.5t

30 S4012HXSS SCREW, M4x12 UPSET SF SS 58 S4020HXSS SCREW, M4x20 UPSET SF SS

31 S4025HXSS SCREW, M4x25 UPSET SF SS

Note: Items without Bally Part

numbers are not stocked by Bally
Gaming and Systems.

Peripherals 8-15 ©July 2001 Bally Gaming and Systems

 Asahi Seiko Hoppers (cont.) Item # Bally Part # Asahi Seiko Part # Description
1 DH7031M025322 SCOOP. ALUMINUM
2 DH7534M025950 BOWL, HOPPER (PLASTIC)
3 DH7031M025046 PLATE, REGULATOR
4 DH7011M025153 .PROBE PIN
5 DH7011M025093 05 WIRE TERMINAL
6 W5000SR99 WASHER, M5,STAR
7 N5000SN99 NUT.M5 SHOULDER
8 W5012FVW08 WASHER, 5x12X0.8 FLAT
9 M4000HX99 NUT, M4
10 W4000SW99 WASHER, M4 SPLIT
DH-750 Model 53, Slant Top Bowl Assembly (Plastic)
11 W4015FW10 WASHER, 4x15x1.0 FLAT
12 ASH-05000-0108 S 4015C S 99 SCREW, M4X15 COUNTERSUNK
13 ASH-05000-0109 S4015LHSS SCREW, M4x15 LARGE HEAD SS
14 DH7011M025307 04 WIRE TERMINAL
15 W4000SR99 WASHER. M4 STAR
16 N4000SN99 NUT, M4 SHOULDER
17 S4012LH99 SCREW. M4x12 LARGE HEAD
18 ASH-05000-0021 DH7001M025052 INSULATOR
19 S3010LH99 SCREW. M3x10 LARGE HEAD
20 ASH-05000-0113 W3008FW05 WASHER, 3x8x0.5 FLAT
21 W3000SW99 WASHER. M3 SPLIT
22 ASH-05000-0086 N3000HX99 NUT, M3
23 ASH-05000-0018 DH7001M025047 SCREW, BOWL MOUNTING
Note: Items without Bally Part 24 ASH-05000-0019 DH7001M025048 SPRIN6. BOWL MOUNTING, UPPER
numbers are not stocked by Bally 25 ASH-05000-0020 DH7001M025049 SPRING, BOWL MOUNTING, LOWER
Gaming and Systems. 26 ASH-05000-0104 N4006HX99 NUT, M4 SMALL
27 ASH-05000-0038 DH7001M10T081 COLLAR. SPACING ($1 TOKEN ONLY)
28 S4008RHSF SCREW, M4x8 W/SW & FW
29 DH7031M025324 ROLLER, SUPPORT
30 DH7534M025325 BRACKET, SUPPORT

Peripherals 8-16 ©Julyl 2001 Bally Gaming and Systems

 Peripherals
Asahi Seiko Hoppers (cont.)

Item # B ally Part # Asahi Seiko Part # D escription

1 ASH-05000-0020 D H7101M025516 PLATE, AC TUATOR MOUNTING
2 S3010HXSW SC REW, M3x10 UPSET SW SS
3 S3012HXSW SC REW, M3x12 UPSET SW SS
4 ASH-05000-0111 W2000ER99 02 E-RING
5 ASH-05000-0088 D H7101M025522 AC TUATOR, M/S INBOARD
6 ASH-05000-0089 D H7101M025523 SPRING, AC TUATOR
7 S3013RH99 SC REW, M3x13 DH-750 Model 53, Slant Top Escalator Assembly
8 ASH-05000-0140 D H7534M025068 MIC ROSWITC H (D 44L-R1LD )
ASH-05000-0039 D H7001P025013 PROXIMITY SENSOR
9 ASH-05000-0086 N3000HX99 NUT, M3
10 D H7301M025069 BRAC KET. M/S MOUNTING (INBOARD )
11 S3016RH99 SC REW, M3x16
12 D H7534M005601 PLATE, BAC K US 5¢
D H7534M025601 PLATE, BAC K US 25¢
Note: Items without Bally Part
D H7534M10T601 PLATE, BAC K $1T
13 D H7301M005507 GUID E, TOP (L) US 5¢
numbers are not stocked by Bally
ASH-05000-0047 D H7301M025507 GUID E. TOP (L) US 25¢ Gaming and Systems.
ASH-05000-0052 D H7301M10T507 GUID E. TOP (L) $1T
14 D H7534M005604 RAIL. GUID E (L) 2.5t
D H7534M025604 RAIL. GUID E (L) 2.Ot
D H7534M10T604 RAIL, GUID E (L) 3.2t
15 D H7534M025606 C OVER. GUID E (L)
16 ASH-05000-0160 D H7301M005560 GUID E, TOP (R) US 5¢
ASH-05000-0049 D H7301M025560 GUID E, TOP (R) US 25¢
17 D H7534M005605 RAIL. GUID E (L) 2.5t
D H7534M025605 RAIL, GUID E (L) 2.0t
D H7534M025605 RAIL, GUID E (L) 3.2t
18 D H7534M025607 C OVER. GUID E (R)
19 S3010HXSS SC REW, M3x10 UPSET SF SS
20 ASH-05000-0091 D H7101M025525 011 BALL BEARING
21 ASH-05000-0090 D H7101M025524 RETAINER, C HEC K BALL
22 ASH-05000-0092 D H7101M025527 BOLT, M4x1OWING
23 S3012HXSS SC REW, M3x12 UPSET SF SS
24 ASH-05000-0079 D H7534M025565 SUPPORT, ESC ALATOR
25 D H7534M025602 RAIL SPAC ER
26 ASH-05000-0048 D H7301M025514 C OVER, TOP

Peripherals 8-17 ©July 2001 Bally Gaming and Systems

Asahi Seiko Hoppers (cont.)

Asahi Seiko DH-750 Hopper Model 51, Bar Top (AS-03107-SERIES)

DH-750 Model 51 Hopper Assembly

Peripherals 8-18 ©Julyl 2001 Bally Gaming and Systems

 Peripherals
Asahi Seiko Hoppers (cont.)

Asahi Seiko DH-750 Hopper Model 51, Bar Top (AS-03107-SERIES) (cont)

Item # Bally Part # Asahi Seiko Part # Description Item # Bally Part # Asahi Seiko Part # Description

1 DH7991M025001 PLATE, CHASSIS 37 ASH-05000-0016 DH7001M025037 SPRING, DISC

2 DH7534M025002 FRAME, SIDE (R 38 W4015FW10 WASHER, 4x15x1.0 FLAT
3 DH7514M025003 FRAME, SIDE (L 39 ASH-05000-0170 S4008LHSS SCREW. M4x8 TRUSS HEAD SS
4 DH7534M025004 PLATE. BASE
40 ASH-05000-0108 S 4015C S 99 SCREW. M4x15 COUNTERSUNK
5 W4000SW99 WASHER, M4 SPLIT
41 W4010FW10 WASHER, 4x10x1.0 FLAT (US 5¢ ONLY)
6 S4006RHSW SCREW, M4x6 W/SW
42 ASH-05000-0029 DH7001M025073 SEPARATOR, COIN
7 ASH-05000-0005 DH7001M025007 PIN, MOTOR DRIVE
43 ASH-05000-0030 DH7001M025074 RETAINER, SEPARATOR
8 ASH-05000-0040 DH7004M025008 MOTOR, 24VDC (DME44S7C-272)
ASH-05000-0037 DH7001M10T074 RETAINER, SEPARATOR. $1 TOKEN
9 DH7001M025055 HANDLE
10 ASH-05000-0097 DH7101M025536 BRACKET, ESCALATOR MOUNTING 44 S4010HXSS SCREW, M4x10 UPSET SF SS

11 ASH-05000-0168 DH7101M005530 GUIDE, TRANSITION (R), US 5¢ 45 S4014HXSS SCREW. M4x14 UPSET SF SS

DH7101M025530 GUIDE. TRANSITION (R), US 25¢ 46 S3010HXSS SCREW, M3x10 UPSET SF SS

ASH-05000-0044 DH7101M10T530 GUIDE. TRANSITION (R). $1 TOKEN 47 S4012HXSS SCREW, M4x12 UPSET SF SS
12 ASH-05000-0169 DH7101M005531 GUIDE, TRANSITION (L), US 5¢ 48 S4008HXSW SCREW, M4x8 UPSET SW SS
DH7101M025531 GUIDE, TRANSITION (L), US 25¢ 49 ASH-05000-0022 DH7001M025057 CAST FRAME
ASH-05000-0045 DH7101M10T531 GUIDE, TRANSITION (L), $1 TOKEN
50 DH7001M025058 06 BALL BEARING
13 ASH-05000-0077 DH7534M025529 COVER, TRANSITION (R)
51 DH7001M025059 RETAINER, BEARING
14 ASH-05000-0096 DH7101M025534 PLATE, COIN SLIDE
52 DH7001M025064 WASHER, ROLLER LEVER
15 DH7514M025918 LEVER, ROLLER
53 S4025LHSS SCREW, M4x25 LARGE HEAD. SS
16 ASH-05000-0006 DH7001M025016 SPRING, ROLLER LEVER
54 DH7001M005070 PLATE, ADJUSTING, US 5¢
17 ASH-05000-0007 DH7001M025017 PIN, ROLLER LEVER
18 ASH-05000-0008 DH7001M025018 BEARING, ROLLER LEVER ASH-05000-0026 DH7001M025070 PLATE, ADJUSTING, US 25¢

19 ASH-05000-0112 W3000ER99 03 E-RING DH7001M10T070 PLATE, ADJUSTING, $1 TOKEN

20 N4000HX99 NUT, M4 55 DH7001M005071 RUBBER, JUMP, US 5¢

21 B4012HX99 BOLT, M4x12 ASH-05000-0027 DH7001M025071 RUBBER, JUMP, US 25¢
22 ASH-05000-0113 W3008FW08 WASHER, 3x8x0,8 FLAT ASH-05000-0036 DH7001M10T071 RUBBER, JUMP. $1 TOKEN
23 ASH-05000-0106 S3010RH99 SCREW, M3x10 56 ASH-05000-0004 DH7001M005072 COVER. JUMP, US 5¢
24 ASH-05000-0086 N3000HX99 NUT, M3
ASH-05000-0028 DH7001M025072 COVER, JUMP
25 ASH-05000-0002 DH7001M005025 KNIFE, US 5¢
57 DH7514M025650 SHIM, TRANSITION (L) O.3t
ASH-05000-0009 DH7001M025025 KNIFE. US 25¢
DH7514M10T650 SHIM, TRANSITION (L) 0.5t
ASH-05000-0034 DH7001M10T025 KNIFE, $1 TOKEN
58 DH7514M025915 BRACKET, OPTIC MOUNTING
26 ASH-05000-0010 DH7001M025026 BOSS, PLASTIC
59 DH7514M025916 FLAG, OPTIC
27 ASH-05000-0011 DH7001M025027 SCREW, BEVEL-HEADED
28 DH7101M10T538 COVER, TRANSITION (L) $1T 60 DH7514M025917 COVER, OPTIC

29 ASH-05000-0099 DH7101M025538 COVER, TRANSITION (L) 61 DH7514M025920 OPTIC

30 S4012HXSS SCREW, M4x12 UPSET SF SS 62 N3000LN99 NUT, M3 NYLON LOCK

31 S4025HXSS SCREW, M4x25 UPSET SF SS 63 S3005RHSF SCREW, M3x5 W/SW & FW
32 ASH-05000-0001 B4025HXSS BOLT. M4x25, SS 64 S3595TP99 SCREW, M3.5x9.5 TAPPING
33 ASH-05000-0003 DH7001M005033 DISC, US 5¢
65 S4020HXSS SCREW, M4x20 UPSET SF SS
ASH-05000-0012 DH7001M025033 DISC, US 25¢
ASH-05000-0035 DH7001M10T033 DISC, $1 TOKEN
34 ASH-05000-0013 DH7001M025034 SPRING, STIRRING
35 ASH-05000-0014 DH7001M025035 COVER, SPRING
36 ASH-05000-0015 DH7001M025036 HOLDER, SPRING

Note: Items without Bally Part

numbers are not stocked by Bally
Gaming and Systems.

Peripherals 8-19 ©July 2001 Bally Gaming and Systems

Asahi Seiko Hoppers (cont.) Item # Bally Part # Asahi Seiko Part # Description

1 DH7031M025322 SCOOP. ALUMINUM

2 DH7514M025050 BOWL, HOPPER

3 S4008RHSF SCREW, M4x8 W/SW & FW

4 DH7031M025046 PLATE, REGULATOR

5 DH7011M025153 PROBE PIN

6 DH7011M025093 05 WIRE TERMINAL

7 W5000SR99 WASHER, M5 STAR

8 N5000SN99 NUT. M5 SHOULDER

9 W5012PW08 WASHER, 5x12x0.8 FLAT

10 N4000HX99 NUT, M4

11 W4000SW99 WASHER, M4 SPLIT

12 W4015FW10 WASHER, 4x15x1.0 FLAT

13 ASH-05000-0108 S 4015C S 99 SCREW. M4x15 COUNTERSUNK

14 ASH-05000-0109 S4015LHSS SCREW, M4x15 LARGE HEAD SS

15 DH7011M025307 04 WIRE TERMINAL

16 W4000SR99 WASHER, M4 STAR

17 N4000SN99 NUT, M4 SHOULDER

18 S4010LH99 SCREW, M4x1O LARGE HEAD

DH-750 Model 51, Bar Top Bowl Assembly 19 ASH-05000-0021 DH7001M025052 INSULATOR

20 S3010LH99 SCREW. M3x10 LARGE HEAD

21 ASH-05000-0113 W3008FW05 WASHER, 3x8x0.5 FLAT

22 W3000SW99 WASHER, M3 SPLIT

23 ASH-05000-0086 N3000HX99 NUT, M3

24 ASH-05000-0018 DH7001M025047 SCREW, BOWL MOUNTING

25 ASH-05000-0019 DH7001M025048 SPRING, BOWL MOUNTING, UPPER

26 ASH-05000-0020 DH7001M025049 SPRING, BOWL MOUNTING, LOWER

27 ASH-05000-0104 N4006HX99 NUT, M4 SMALL

28 ASH-05000-0038 DH7001M10T081 COLLAR, SPACING ($1 TOKEN ONLY)

Note: Items without Bally Part # are not stocked by 29 W4010FW16 WASHER, 4x10x1.6 FLAT (5^ ONLY)

Bally Gaming and Systems. 30 DH7031M025324 ROLLER. SUPPORT

31 DH7534M025325 BRACKET, BOWL SUPPORT

Peripherals 8-20 ©Julyl 2001 Bally Gaming and Systems

 Peripherals
Asahi Seiko Hoppers (cont.)

Item # B ally Part # Asahi Seiko Part # D escription

I D H7514M005505 PLATE, BAC K, US 5¢

D H7514M025505 PLATE, BAC K, US 25¢

D H7514M10T505 PLATE. BAC K, $1 TOKEN Note: Items without Bally Part

2 D H7301M005507 GUID E. 1 UP (L), US 5¢ numbers are not stocked by Bally
ASH-05000-0047 D H7301M025507 GUID E, TOP (L), US 25¢ Gaming and Systems.
ASH-05000-0052 D H7301M10T507 GUID E, TOP (L). $1 TOKEN

3 D H7301M005560 GUID E, TOP (R). US 5¢

ASH-05000-0049 D H7301M025560 GUID E, TOP (R), US 25¢

4 ASH-05000-0146 D H7514M005506 RAIL, GUID E (L), US 5¢

ASH-05000-0147 D H7514M025506 RAIL, GUID E (L). US 25¢

D H7514M10T506 RAIL. GUID E (L), $1 TOKEN

5 ASH-05000-0149 D H7514M005508 RAIL, GUID E (R), US 5¢

ASH-05000-0150 D H7514M025508 RAIL, GUID E (R), US 25¢

DH-750 Model 51, Bar Top Escalator Assembly
ASH-05000-0151 D H7514M10T508 RAIL, GUID E (R). $1 TOKEN

6 ASH-05000-0152 D H7514M025509 C OVER, GUID E (L)

7 ASH-05000-0153 D H7514M025511 C OVER, GUID E (R)

8 ASH-05000-0048 D H7301M025514 C OVER, TOP

9 D H7101M025524 BRAC KET. BALL RETAINING

10 D H7101M025525 011 BALL BEARING

11 S3012HXSS SC REW, M3x12 UPSET SF SS

12 S3012HXSS SC REW. M3x12 UPSET SF SS

13 S3010HXSS SC REW, M3x1O UPSET SF SS

14 D H7101M025527 BOLT, M4 WING

15 ASH-05000-0086 N3000HX99 NUT, M3

16 D H7101M025516 PLATE, AC TUATOR MOUNTING

17 ASH-05000-0025 D H7001M025069 PLATE, M/S MOUNTING, INBOARD

18 S3016RH99 SC REW, M3x16

19 S3010HXSW SC REW, M3x1O UPSET SWSS

20 S3012HXSW SC REW, M3x12 UPSET SW SS

21 D H7301M025522 AC TUATOR, M/S, INBOARD

22 D H7101M025523 SPRING, AC TUATOR

23 ASH-05000-0111 W2000ER99 02 E-RING

Peripherals 8-21 ©July 2001 Bally Gaming and Systems

Ithaca Series 70
Printer
Ithaca Perpherals, Inc.

Tel: +1 607 257 8901

Fax: +1 607 257 8922

Description:
The IPI Series 70 Printer is a nine-pin impact
printer designed for video lottery systems. It prints
receipt and journal entries for each transaction using
two-ply paper.

Features
Print Speed
200 characters per second in normal mode Connection
100 characters per second in double-wide mode
Printer (Centronics)
Interface
Centronics Parallel Pin Wire Signal Pin Wire Signal Pin Wire Signal Pin Wire Signal
RS-232 1 BK/RD Strobe 10 No connection 19 No connection 28 No connection

2 BR Data 1 11 WT/BL Busy 20 No connection 29 No connection

Character Sets 3 WT Data 2 12 WT/BR Paper End 21 No connection 30 No connection

IBM Character Set I 4 OR/BL Data 3 13 WT/OR Select 22 No connection 31 BR/BK Printer Reset
5 YE Data 4 14 No connection 23 No connection 32 WT/BK Printer Fault
IBM Character Set II
6 OR Data 5 15 No connection 24 No connection 33 BK Ground
7 GY Data 6 16 BK Ground 25 No connection 34 No connection
Character Modes 8 BL Data 7 17 No connection 26 No connection 35 No connection

Normal Mode (17, 12, 10 characters per inch) 9 YE/WT Data 8 18 No connection 27 No connection 36 No connection

Double-Wide Mode

Line Spacing
Eight lines per inch
Selectable in n/216 inch increments

Automatic Knife Cutter

.002 to .007 inch ply thickness
Backplane (Dual Row Header)
Full cut only
Pin Wire Signal Pin Wire Signal

2-Ply Receipt-Journal Printing 1 BR Data 1 14 No Connection

2 WT/OR Select 15 YE/WT Data 8

Low Paper Sensor 3 WT Data 2 16 No Connection

4 WT/BL Busy 17 BK/RD Strobe

Mounting
Vertical 5 OR/BL Data 3 18 No Connection

Horizontal 6 No Connection 19 BR/BK Printer Reset

7 YE Data 4 20 No Connection

Graphics 8 BK-1 Ground 21 WT/BK Printer Fault

Block graphics (characters from character set) 9 OR Data 5 22 No Connection
Dot addressable graphics 10 BK-2 Ground 23 WT/BR Paper End
11 GY Data 6 24 No Connection

12 No Connection 25 No Connection

13 BL Data 7 26 No Connection

Peripherals 8-22 © July 2001 Bally Gaming and Systems

 Peripherals
Changing the Ribbon Cassette • To install the new cassette hold down the
Cutter Blade Cover.

Change the cassette when the print becomes • Align the grooves at the top of the cassette with
faded. Worn ribbons can damage the print head. the tabs on the Printhead Carriage Assembly.

• Pivot the ribbon cassette into the Printhead

Carriage Assembly until it snaps into place.

• Tighten the ribbon by turning the knob on the

cassette clockwise.

• To remove the old cassette slide the Printhead Ordering Supplies

Carriage Assembly to the middle. Order supplies by calling or
faxing lthaca Peripherals Inc.
• Hold down the Cutter Blade Cover.
Phone: (607) 257-8901, ask for Sales
• Grasp the bottom of the ribbon cassette and
pull out. Fax: (607)257-8922

The following parts are available:

Description Part #
Paper (two-ply) 98-0558
Ribbon Cassette (black or dark purple) 06-0560 (case of 12)
Supply Roll Spindle Large Diameter 09-1230
Supply Roll Spindle Small Diameter 09-1494
Take-up Spindle Take-up Core 06-0597
Take-up Flange 06-0599
Take-up Assembly (both core and flange) 06-0993
Power Cord 06-0561
Fuses 1.0 Amp, 125 Volt 150-9810010
1.5 Amp, 125 Volt 150-9810015
Printhead 06-0565
Printhead Clamp 06-0571

Peripherals 8-23 © July 2001 Bally Gaming and Systems

Changing Paper

Change the Supply Roll paper when you see the • Trim enough of the new Supply Roll for a
pink stripe on the receipt paper or when the terminal straight edge free from glue.
indicates the paper is low. Although the pink stripe
appears with eight to ten feet left on the roll, the printer • Put the spindle that was removed from the used
will print only 21 inches after the Paper Low sensor supply roll into the new roll so that the white reciept
activates. paper is on the outside (See figure below). Snap the
spindle into the lower set of snaps in the Bucket.

• Hold down the Cuter Blade Cover and push the

paper up through the throat in the back of the Bucket
until the paper passes the printhead.

• The receipt and journal thread through different

• Unsnap the Journal Takeup Roll paths. Using the Thumb Wheel ( Gear on the left side.
Spindle from the bracket. Tear off the See bottom figure) to advance the paper, guide the
yellow journal paper using the Shear journal and reciept paper so that they are separated by
Plate. the Shear Plate.

• Remove the spindle from the journal by

unscrewing the left flange in the direction of the OFF
arrow. Secure and store
the journal roll as
required.

• Unsnap the
Supply Roll Spindle from the bracket.
Hold down the Cutter Blade Cover and • Advance about six inches of paper then tear off
pull the remaining paper out of the only the white receipt ply.
printer.

•Remove the spindle from the used

supply roll and set it aside. Don’t throw it
away.

Peripherals 8-24 © July 2001 Bally Gaming and Systems

 Peripherals
• Reassemble the Journal Takeup Spindle by Replacing the Printhead
turning the the flange in the direction of the ON arrow. Caution: The printhead may be hot.
Do not overtighten.

• Fold about ½” of the journal paper and insert it

into the groove of the Journal Takeup Spindle so that the
gear is to the right.

• Turn the Journal Takeup Spindle a few turns in

the direction of the ON arrow to take up the excess
journal paper.

• Remove the ribbon cassette.

• Release the printhead by unfastening the
Printhead Clamp. Pull the tab on the left to swing it
open.

• Hold down the Cutter Blade Cover.

• Pull the printhead free from the edge connecter
and carriage.

Function Switch • Using the guide on the printhead, slide the new
printhead onto the carriage and into the edge connector.
The Function
Switch is a momentary
• Secure the printhead with the Printhead Clamp.
two-position switch that
provides the following
• Put the ribbon cassette back in.
functions:
• Check the print quality. Use the blue lever on
the side of the carriage for lighter or darker printing.

With power ON:

Left: Incremental paper advance

Right: Auto paper advance and cut.

Position switch with power OFF, then power ON:

Left: Print Test

Right: Hex Data Dump

Peripherals 8-25 © July 2001 Bally Gaming and Systems

Vivo™ Printers
Seiko Instruments USA Inc.
Micro Printer Division
2990 West Lornita Blvd., Torrance, CA 90505
Phone: (800) 553-6570 * Facsimile: (310) 517-8154
E-Mail: [email protected]
World Wide Web:http://www.seikoprinters.com

Operator Interface PSA-66-ST Direct Thermal Printer System

The printer has status indicators and two controls.

The status indicators are part of the Keypad. They are
LEDs laleled STATUS and ERROR. The Operator
controls are the Keypad and the Platen Release Lever.

Component Identification

Paper Orientation Keypad

Label Paper Advance

Keypad Error
LED
Mechanism Fastening Keypad
Screw Status LED

Platen Release
Lever

Note: The Keypad CUT function is

inoperative.

Peripherals 8-26 © June 2001 Bally Gaming and Systems

 Peripherals
Vivo™ Printers (cont.) Keypad LED Operation
The following table lists the conditions reported by
the keypad LEDs.
Loading Paper
CONDITION STATUS LED E E R R LE D
To load paper, pull open the printer drawer until
the paper tray is completely accessible. Place the Unit in Powered Off 0F F 0F F
paper stack in the printer as indicated by the band Unit Ready ON OFF
around the stack and the Paper Orientation Label in Unit Flushed ON ON
the paper tray. Present the paper to the Paperfeed slot.
Paper out OFF ON
The automatic loading feature of this system will Head Up OFF ON
advance at least one ticket through the printer. The
Temperature Error OFF MED BLINK
Platen Release Lever and the paper advance button are
provided as support, but usually are not required to Voltage Error OFF SLOW BLINK
load paper. Print Head Error ON FAST BLINK
Flash Memory Error SLOW BLINK MED BLINK
Buffer Overflow OFF FAST BLINK
Missing Black Index Mark ON FAST BLINK
P a p e r Ja m ON FAST BLINK

Error Conditions
PAPER OUT: The printer detects that paper is not
present. The printer scans for a paper-out condition at all
times. Remedy by loading a new paper stack.

Place paper stack in Paper Tray HEAD UP: This condition results from lowering the Platen
Release Lever. To remedy, raise the blue lever on the side
of the unit.

TEMPERATURE ERROR:. The printer has over-heated. If the

printer is operating environment is at room-temperature,
INSERT PAPER HERE this error would most likely be the result of a hardware
problem. The printer will automatically resume operation
when the head temperature cools within operational limits.

VOLTAGE ERROR: The printer detected a power supply voltage

(+24VDC to +25VDC) outside of legal limits. The printer
will automatically resume operation when the power supply
is within range.
Paper Orientation Label
PRINT HEAD ERROR: The printer senses an interfacing
problem with the thermal print head. The error state remains
until the power is cycled or the unit is reset. If the problem
persists, the printer will require service.

FLASH MEMORY ERROR: The printer is unable to program the

Flash memory on the board. The printer will remain in error
state until the power is cycled or the unit is reset. If the
problem persists, the printer will require service before font
or graphic data can be downloaded.

Present end of paper stack to the paper insertion slot BUFFER OVERFLOW: A buffer overflow typically results from
a mismatch in handshaking. The printer will remain in error

Peripherals 8-27 © June 2001 Bally Gaming and Systems

Vivo™ Printers (cont.) Servicing the Printer
Accessing the Paper Path
Error Conditions (cont.)
The paper path can be accessed by loosening the
state until the power is cycled or the unit is reset.
Mechanism Fastening Screw. The head swivels to
expose the paper path.
MISSING INDEX MARK: While feeding paper or while printing,
a black mark has not been seen within approximately 10”
of paper. Remedy by using the correct paper in the printer,
or installing the paper in the correct orientation. The
condition is removed by raising the Platen Release Lever
(presumably to change the paper).

PAPER JAM: The printer detected an obstruction in the

paper path. Remedy by opening the printer head and
inspecting for a jammed ticket.

Accessing the Paper Path

Self Test
If the Keypad FEED is held during power on or
reset, a self test will be triggered. Proper operation will
result in the printing of a configuration ticket. Separating the Drawer

The drawer can be removed from the stationary

module by the following procedure.

• Remove power from the printer.

Model: PSA-66-ST
Firmware: 1.0.0.0.0
• Slide the drawer open until
COMMUNICATION it locks into position.
Interface: serial
Baud Rate: 19200 • Spread the latching cable
Data Bits: 8 connector to release the ribbon
Parity: NONE cable for removal.
Handshaking: HARDWARE

PRINT CONTROL
Darkness Control: +00%
Black Bar Index: Disabled
Print On Demand: Disabled
Auto Sleep Timer: Off

SYSTEM RESOURCES
FLASH -Used: 000000
-Free: 024064

LIBRARY INVENTORY
Templates: Ribbon Cable
Print Regions:
Graphics:
Fonts: 3(0), 7(0), 8(0), 5(0) Note: The connectors of the ribbon
cable are keyed. The black connector fits
into the stationary unit. The gray
connector fits into the drawer.
Sample Self-Test Ticket

Peripherals 8-28 © June 2001 Bally Gaming and Systems

 Peripherals
Vivo™ Printers (cont.)
Separating the Drawer (cont.)

• Press the spring-loaded release bar on the front

of the drawer to unlock it from the stationary unit. Pull
on the drawer to separate.

Release Bar

Dip Switch

Caution: Do not disturb DIP Switch

settings on the stationary unit.
Switches 7 and 9 must be ON for
proper operation.

Peripherals 8-29 © June 2001 Bally Gaming and Systems

 Accounting System Interface
All Bally Gaming machines can interface accounting systems through a connection on the Backplane Board.
Protocols supproted are SDS® and SAS®.

Evo® V87 Game Maker® V7

J10 SYSTEM VCC

1
232RS1 TX
3
232RS0 RX
5
232RS3 RTS
7
232RS2 CTS
9
R4
232RS4 DSR
11 150 JMISER
METER0 TOTAL_IN_MTR
13 CHANGE SERVICE 13
15
METER1 TOTAL_OUT_MTR
17
AGND 25
METER2 HARD_DROP_MTR
METER3
19 HINGE A 12
ATTNDT_PAID_MTR
DOOR NC
21 SPARE DRV3 24
23
LINK7 CHANGE_SERV_RLY
25
ATTEN PD METER 11
HOPR_CN_OUT_SW 2 5VDC 23
BUSY/COIN OUT
IOP DR NC MPU PRESENT
4 DROP METER 10
6
LINK6 END_OF_GAME_SIG
8
SYSTEM RESET 2 22
BILL DOOR N/O BV CASHBOX DOOR 9
LINK COIN1 SOL
10 TOT OUT METER
COIN_CREDIT_SIG
232RS5
12 COIN DEFLECTOR 21
14
HIDRIVE5 DEF_SOL
16
TOTAL IN METER 8
R2 HIDRIVE7 SYSTEM RESET
18 MDTR 20
2 1 OPTIC POWER 3
VCC HIDRIVE2 TILT_RLY
20 AGND 7
22
LINK COIN1 19
180 OHM 1/2W 24
+5V 26 MDCD 6
+24V 27 DOOR 4 18
29
+12V 31
MCTS 5
7.5VAC 33 EOG SOL 17
METER4 SOFT_DROP_MTR
LAMP15
35 MRTS 4
JACKPOT_BELL
37
DOORSW6 BV CASHBOX PRESENT
39
MPU PRESENT 16
BILL DR NC 3
28 MRXD
LINK0 DOOR_SW_SIG
LINK1 TOTAL_IN_SIG
30 COIN OUT- PRINTER BUSY 15
32
LINK5 JACKPOT1_SIG MTXD 2
34
LINK2 KEY_SW_SIG
36 FWD ENABLE- DATA2 14
38 AGND 1
40

40 PIN HEADER CONNECTOR DB25

AS-03356-0501 Backplane Board AS-03356-0247 Backplane Board

Game Maker® V72 ProSlot® 6000

SYSTEM

1
MRXD TX
3
MTXD RX
5
MRTS RTS
7 J10
MCTS CTS
9
MDCD DSR
11 1 2
13 TXD4 COINOUT SWITCH
METER 1 TOTAL_IN_MTR 3 4
15 RXD4 MPU PRESENT
METER 2 TOTAL_OUT_MTR 5 6
METER 3
17 RTS4 END OF GAME
HARD_DROP_MTR
19 7 8
METER 4 ATTNDT_PAID_MTR
CTS4 BV CASHBOX DOOR
21
DSR4 9 10 COIN CREDIT SIGNAL
HINGE_A
23 11 12
CHANGE/SERVICE CHANGE_SERV_RLY DTR4
25 13 14
2 TOTAL IN METER DIVERTER SOL
BUSY/COIN OUT HOPR_CN_OUT_SW 15 16
4 TOTAL OUT METER SYSTEM RESET
MPU PRESENT MPU PRESENT 17 18
EOG SOL
6 TOTAL DROP METER OPTIC POWER 3
END_OF_GAME_SIG 19 20
8 ATTEND PD METER TILT RELAY
DOOR 4 BV CASHBOX DOOR 21 22
10 DOOR NC
LINK COIN1 COIN_CREDIT_SIG
12 23 24
MDTR BH 2ND MOTOR +5V
14 25 26
COIN DEFLECT DEF_SOL BV DOOR NC
R11
SYSTEM RESET 1
16 +24V 27 28
SYSTEM RESET GAME DOOR OPEN
18
VCC OPTIC POWER 3 29 30
TILT RELAY TILT_RLY
20
+12V TOTAL IN SIGNAL
31 32
22
7.5VAC JACKPOT SIGNAL
68 1/2W 24 33 34
SPARE HARD METER KEYSWITCH SIGNAL
1

+5V 26 35 36
R15 +24V JACKPOT BELL COIN OFF
68 1/2W 27 37 38
29 CASHBOX PRESENT
+12V 39 40
31
7.5VAC 33
METER 5
2

SOFT_DROP_MTR
35
JACKPOT BELL JACKPOT_BELL
37
DOOR 5 BV CASHBOX PRESENT
39
DOOR 4
DOOR OPEN SOL DOOR_SW_SIG
28 SYSTEM
30
LINK COIN1 TOTAL_IN_SIG
32
JPOT 1 SOL JACKPOT1_SIG
34
KEY SOL KEY_SW_SIG
36
COIN ON
38
40
DR 40 HEADER

AS-03356-0432 Backplane Board AS-03356-0445 Backplane Board

Peripherals 8-30 © July 2001 Bally Gaming and Systems

 Peripherals
Accounting System Interface (cont.)
ProSlot® 5500
J6

1
FORWARD SENSE 14
MISER TXD 2
COIN OUT SWITCH 15
MISER RXD 3
MPU PRESENT 16
MISER RTS 4
END OF GAME 17
MISER CTS 5
BV CASHBOX DOOR 18 Note: See Module MK10-SVMOD-
MISER DSR 6 0003 SDS Parts Reference for
COIN IN 19 hardware requirements.
7
MISER DTR 20
TOTAL IN METER 8
DIVERTER SOL 21
TOTAL OUT METER 9
~SYSTEM RESET 22
DROP METER 10
5V DETECT 23
ATTEND PD METER 11
TILT RELAY 24
HINGE A 12
25
CHANGE/SVC RELAY 13

MASTERCOM
AS-03356-0207 Backplane board

CBL-20234-0001 System Interface Cable

Peripherals 8-31 © July 2001 Bally Gaming and Systems