RPH (11th Edition) - Installation and Operating Manual

Process Pump
RPH
Standard bearing assemblies B02 to B07
Tandem bearing assemblies B02 to B07
Cooled/uncooled
Installation/Operating
Manual
Installation/Operating Manual RPH
Original operating manual
KSB Aktiengesellschaft Pegnitz
All rights reserved. Contents provided herein must neither be distributed, copied, reproduced,
processed for any other purpose, nor otherwise transmitted to a third party without KSB´s express
written consent.
Subject to technical modification without prior notice.
© KSB Aktiengesellschaft Frankenthal 30.12.2009

Contents
Contents
Glossary ................................................................................................ 5
1 General ................................................................................................ 6
1.1 Principles .......................................................................................................... 6
1.2 Installation of partly completed machinery .................................................. 6
1.3 Target group ................................................................................................... 6
1.4 Other applicable documents .......................................................................... 6
1.5 Symbols ............................................................................................................ 6
2 Safety ................................................................................................... 8
2.1 Key to safety symbols/markings ..................................................................... 8
2.2 General ............................................................................................................ 8
2.3 Intended use .................................................................................................... 8
2.4 Personnel qualification and training ............................................................. 9
2.5 Consequences and risks caused by non-compliance with these operating
instructions ...................................................................................................... 9
2.6 Safety awareness ............................................................................................. 9
2.7 Safety information for the operator/user .................................................... 10
2.8 Safety information for maintenance, inspection and installation work ... 10
2.9 Unauthorised modes of operation ............................................................... 10
2.10 Explosion protection ..................................................................................... 10
3 Transport/Temporary Storage/Disposal ........................................... 13

3.1 Transport ....................................................................................................... 13
3.2 Storage and preservation ............................................................................. 13
3.3 Return to supplier ......................................................................................... 14
3.4 Disposal .......................................................................................................... 14
4 Description of the Pump (Set) .......................................................... 15

4.1 General description ....................................................................................... 15
4.2 Designation ................................................................................................... 15
4.3 Name plate .................................................................................................... 15
4.4 Design details ................................................................................................ 15
4.5 Design and function ...................................................................................... 17
4.6 Noise characteristics ..................................................................................... 18
4.7 Scope of supply ............................................................................................. 18
4.8 Dimensions and weights ............................................................................... 19
5 Installation at Site ............................................................................. 20

5.1 Safety regulations ......................................................................................... 20
5.2 Checking the site before installation ........................................................... 20
5.3 Installing the pump set ................................................................................. 20
5.4 Piping ............................................................................................................. 21
RPH 3 of 68
Contents
5.5 Protective equipment ................................................................................... 24

5.6 Checking the coupling alignment ................................................................ 25
5.7 Aligning the pump and motor ..................................................................... 25
5.8 Electrical connection ..................................................................................... 26
5.9 Checking the direction of rotation .............................................................. 27
6 Commissioning/Start-up/Shutdown ................................................. 29
6.1 Commissioning/start-up ................................................................................ 29
6.2 Operating limits ............................................................................................ 36
6.3 Shutdown/storage/preservation ................................................................... 38
6.4 Returning to service after storage ............................................................... 38
7 Servicing/Maintenance ...................................................................... 39
7.1 Safety regulations ......................................................................................... 39
7.2 Servicing/inspection ...................................................................................... 39
7.3 Drainage/disposal .......................................................................................... 44
7.4 Dismantling the pump set ............................................................................ 45
7.5 Reassembling the pump set .......................................................................... 47
7.6 Tightening torques ....................................................................................... 51
7.7 Spare parts stock ........................................................................................... 54
8 Trouble-shooting ............................................................................... 58
9 Related Documents ........................................................................... 60

9.1 General assembly drawing with list of components ................................... 60
10 EC Declaration of Conformity .......................................................... 65
11 Certificate of Decontamination ....................................................... 66
Index .................................................................................................. 67
4 of 68 RPH
Glossary
Glossary
Back pull-out design Pool of pumps

The complete back pull-out unit can be pulled Pumps which are purchased and stored
out without having to remove the pump casing independently of their later use
from the piping.
Pump
Back pull-out unit Machine without drive, additional components
Pump without pump casing; partly completed or accessories
machinery
Pump set
Certificate of decontamination Complete pump set consisting of pump, drive,
A certificate of decontamination certifies that additional components and accessories
the pump (set) has been properly drained to
eliminate any environmental and health
Suction lift line/suction head line
hazards arising from components in contact
with the fluid handled. The line which is connected to the suction
nozzle
Discharge line
The line which is connected to the discharge
nozzle
Hydraulic system
The part of the pump in which the kinetic
energy is converted into pressure energy.
RPH 5 of 68
1 General
1 General
1.1 Principles
This manual is supplied as an integral part of the type series and variants indicated
on the front cover. It describes the proper and safe use of this equipment in all
phases of operation.
The name plate indicates the type series and size, the main operating data, the order
number and the order item number. The order number and order item number
clearly identify the pump (set) and serve as identification for all further business
processes.
In the event of damage, immediately contact your nearest KSB service centre
immediately to maintain the right to claim under warranty.
Noise characteristics (⇨ Section 4.6 Page 18)
1.2 Installation of partly completed machinery

To install partly completed machinery supplied by KSB, please refer to the sub-
sections under Servicing/Maintenance. (⇨ Section 7.5.5 Page 50)
1.3 Target group

This manual is aimed at the target group of trained and qualified specialist technical
personnel. (⇨ Section 2.4 Page 9)
1.4 Other applicable documents

Table 1: Overview of other applicable documents
Document Contents
Data sheet Description of the technical data of the pump
(set)
General arrangement drawing/ Description of mating and installation dimensions
Outline drawing for the pump (set)
Drawing of auxiliary connections Description of auxiliary connections
Hydraulic characteristic curve Characteristic curves showing head, NPSH
required, efficiency and power input
General assembly drawing1) Sectional drawing of the pump
Sub-supplier documentation1) Operating manuals and other documentation of
accessories and integrated machinery components
Spare parts lists1) Description of spare parts
Piping layout1) Description of auxiliary piping
List of components 1) Description of all pump components
1.5 Symbols
Table 2: Symbols used in this manual
Symbol Description
✓ Conditions which need to be fulfilled before proceeding with the
step-by-step instructions
⊳ Safety instructions
⇨ Result of an action
⇨ Cross-references
1) If agreed to be included in the scope of supply
6 of 68 RPH
1 General
Symbol Description
1. Step-by-step instructions
2.
Note
Recommendations and important information on how to handle
the product
RPH 7 of 68
2 Safety
2 Safety
All the information contained in this section refers to hazardous situations.
! DANGER
2.1 Key to safety symbols/markings

Table 3: Definition of safety symbols/markings
Symbol Description
! DANGER DANGER
This signal word indicates a high-risk hazard which, if not avoided,
will result in death or serious injury.
! WARNING WARNING
This signal word indicates a medium-risk hazard which, if not
avoided, could result in death or serious injury.
CAUTION CAUTION
This signal word indicates a hazard which, if not avoided, could
result in damage to the machine and its functions.
Explosion protection
This symbol identifies information about avoiding explosions in
potentially explosive atmospheres in accordance with EC Directive
94/9/EC (ATEX).
General hazard
In conjunction with one of the signal words this symbol indicates a
hazard which will or could result in death or serious injury.
Electrical hazard
In conjunction with one of the signal words this symbol indicates a
hazard involving electrical voltage and identifies information
about protection against electrical voltage.
Machine damage
In conjunction with the signal word CAUTION this symbol indicates
a hazard for the machine and its functions.
2.2 General
This manual contains general installation, operating and maintenance instructions
that must be observed to ensure safe pump operation and prevent injury and
damage to property.
The safety instructions in all sections of this manual must be complied with.
This manual must be read and completely understood by the responsible specialist
personnel/operators prior to installation and commissioning.
The contents of this manual must be available to the specialist personnel at the site
at all times.
Instructions attached directly to the pump must always be complied with and be kept
in a perfectly legible condition at all times. This applies to, for example:
▪ Arrow indicating the direction of rotation
▪ Markings for connections
▪ Name plate
The operator is responsible for meeting all local regulations which are not taken into
account in this manual.
2.3 Intended use

The pump (set) must only be operated within the operating limits described in the
other applicable documents.
▪ Only operate pumps/pump sets which are in perfect technical condition.
▪ Do not operate partially assembled pumps/pump sets.
8 of 68 RPH
2 Safety
▪ The pump must only be used to handle the fluids specified in the data sheet or
product literature of the respective design variant.
▪ Never operate the pump without the fluid to be handled.
▪ Observe the minimum flow rates indicated in the data sheet or product literature
(to prevent overheating, bearing damage, etc).
▪ Observe the maximum flow rates indicated in the data sheet or product
literature (to prevent overheating, mechanical seal damage, cavitation damage,
bearing damage, etc).
▪ Do not throttle the flow rate on the suction side of the pump (to prevent
cavitation damage).
▪ Consult the manufacturer about any use or mode of operation not described in
the data sheet or product literature.
Prevention of foreseeable misuse

▪ Never open discharge-side shut-off elements further than permitted.
– The maximum flow rate specified in the data sheet or product literature
would be exceeded.
– Risk of cavitation damage
▪ Never exceed the permissible operating limits specified in the data sheet or
product literature regarding pressure, temperature, etc.
▪ Observe all safety information and instructions in this manual.
2.4 Personnel qualification and training

All personnel involved must be fully qualified to install, operate, maintain and
inspect the machinery this manual refers to.
The responsibilities, competence and supervision of all personnel involved in

installation, operation, maintenance and inspection must be clearly defined by the
operator.
Deficits in knowledge must be rectified by sufficiently trained specialist personnel

training and instructing the personnel who will carry out the respective tasks. If
required, the operator can commission the manufacturer/supplier to train the
personnel.
Training on the pump (set) must always be supervised by technical specialist

personnel.
2.5 Consequences and risks caused by non-compliance with these operating

instructions
▪ Non-compliance with these operating instructions will lead to forfeiture of
warranty cover and of any and all rights to claims for damages.
▪ Non-compliance can, for example, have the following consequences:
– Hazards to persons due to electrical, thermal, mechanical and chemical
effects and explosions
– Failure of important product functions
– Failure of prescribed maintenance and servicing practices
– Hazard to the environment due to leakage of hazardous substances
2.6 Safety awareness

In addition to the safety information contained in this manual and the intended use,
the following safety regulations shall be complied with:
▪ Accident prevention, health and safety regulations
▪ Explosion protection regulations
RPH 9 of 68
2 Safety
▪ Safety regulations for handling hazardous substances

▪ Applicable standards and laws
2.7 Safety information for the operator/user

▪ The operator shall fit contact guards for hot, cold or moving parts and check that
the guards function properly.
▪ Do not remove the contact guard while the pump is running.
▪ Connect an earth conductor to the metal jacket if the fluid handled is
electrostatically charged.
▪ Provide the personnel with protective equipment and make sure it is used.
▪ Contain leakages (e.g at the shaft seal) of hazardous fluids handled (e.g.
explosive, toxic, hot) so as to avoid any danger to persons and the environment.
Adhere to all relevant laws.
▪ Eliminate all electrical hazards. (In this respect refer to the applicable national
safety regulations and/or regulations issued by the local energy supply
companies.)
2.8 Safety information for maintenance, inspection and installation work

▪ Modifications or alterations of the pump are only permitted with the
manufacturer's prior consent.
▪ Use only original spare parts or parts authorised by the manufacturer. The use of
other parts can invalidate any liability of the manufacturer for consequential
damage.
▪ The operator ensures that all maintenance, inspection and installation work is
performed by authorised, qualified specialist personnel who are thoroughly
familiar with the manual.
▪ Carry out work on the pump (set) during standstill only.
▪ The pump casing must have cooled down to ambient temperature.
▪ Pump pressure must have been released and the pump must have been drained.
▪ When taking the pump set out of service always adhere to the procedure
described in the manual. (⇨ Section 6.1.13 Page 35)
▪ Decontaminate pumps which handle fluids posing a health hazard. (⇨ Section 7.3
Page 44)
▪ As soon as the work is complete, re-install and/or re-activate any safety-relevant
and protective devices. Before returning the product to service, observe all
instructions on commissioning. (⇨ Section 6.1 Page 29)
2.9 Unauthorised modes of operation

Never operate the pump (set) outside the limits stated in the data sheet and in this
manual.
The warranty relating to the operating reliability and safety of the supplied pump
(set) is only valid if the equipment is used in accordance with its intended use. (⇨
Section 2.3 Page 8)
2.10 Explosion protection

Always observe the instructions on explosion protection given in this section when
! DANGER operating the pump in potentially explosive atmospheres.
10 of 68 RPH
2 Safety
Only pumps/pump sets marked as explosion-proof and identified as such in the data
sheet may be used in potentially explosive atmospheres.
Special conditions apply to the operation of explosion-proof pump sets to EC

Directive 94/9/EC (ATEX).
Especially adhere to the sections in this manual marked with the Ex symbol and the
following sections (⇨ Section 2.10.1 Page 11) to (⇨ Section 2.10.4 Page 12).
The explosion-proof status of the pump set is only assured if the pump set is used in
accordance with its intended use.
Never operate the pump (set) outside the limits stated in the data sheet and on the
name plate.
Prevent impermissible modes of operation at all times.
2.10.1 Marking
Pump The marking on the pump refers to the pump only.
Example of such marking: II 2 G c TX
Refer to the Temperature limits table for the temperatures permitted for the
individual pump variants. (⇨ Section 2.10.2 Page 11)
Shaft coupling An EC manufacturer's declaration is required for the shaft coupling; the shaft
coupling must be marked accordingly.
Motor The motor must be considered separately.
2.10.2 Temperature limits

In normal pump operation, the highest temperatures are to be expected on the
surface of the pump casing, at the shaft seal and in the bearing areas.
The surface temperature at the pump casing corresponds to the temperature of the
fluid handled. If the pump is heated in addition, the operator of the system is
responsible for observing the specified temperature classes and fluid temperature
(operating temperature).
The table below lists the temperature classes and the resulting theoretical
temperature limits of the fluid handled (a possible temperature rise in the shaft seal
area has already been taken into account).
The temperature class specifies the maximum permissible temperature at the surface
of the pump set during operation. For the permissible operating temperature of the
pump in question refer to the data sheet.
Table 4: Temperature limits
Temperature class as per EN 13463-1 Maximum permissible fluid
temperature
T1 Maximum 400 °C2)
T2 280 °C
T3 185 °C
T4 120 °C
T5 85 °C
T6 Only after consultation
with the manufacturer
Temperature class T5 Based on an ambient temperature of 40 °C and proper maintenance and operation,
compliance with temperature class T5 is warranted in the area of the rolling element
bearings. If the ambient temperature exceeds 40 °C, contact the manufacturer.
Temperature class T6 A special design is required to comply with the requirements of temperature class T6
in the bearing area.
Misuse, malfunctions or non-compliance with the instructions may result in

substantially higher temperatures.
2) Depending on the material variant
RPH 11 of 68
2 Safety
If the pump is to be operated at a higher temperature, the data sheet is missing or if

the pump is part of a pool of pumps, contact KSB for the maximum permissible
operating temperature.
2.10.3 Monitoring equipment

The pump (set) must only be operated within the limits specified in the data sheet
and on the name plate.
If the system operator cannot warrant compliance with these operating limits,
appropriate monitoring devices must be used.
Check whether monitoring equipment is required to ensure that the pump set
functions properly.
Contact KSB for further information on monitoring equipment.
2.10.4 Operating limits

The minimum flows indicated in section (⇨ Section 6.2.3 Page 37) refer to water
and water-like fluids. Longer operating periods with these fluids and at the flow
rates indicated will not cause an additional increase in the temperatures on the
pump surface. However, if the physical properties of the fluids handled are different
from water, it is essential to check if an additional heat build-up may occur and if the
minimum flow rate must therefore be increased. The calculation formula in (⇨
Section 6.2.3 Page 37) can be used to check if an additional heat build-up may lead
to a hazardous temperature increase at the pump surface.
12 of 68 RPH
3 Transport/Temporary Storage/Disposal
3.1 Transport
DANGER
The pump (set) could slip out of the suspension arrangement
Danger to life from falling parts!
▷ Always transport the pump (set) in horizontal position.
▷ Never attach the suspension arrangement to the free shaft end or the motor
eyebolt.
▷ Refer to the weights given in the general arrangement drawing.
▷ Observe the local accident prevention regulations.
▷ Use suitable, permitted lifting tackle, e.g. self-tightening lifting tongs.
To transport the pump/pump set suspend it from the lifting tackle as follows.
Fig. 1: Transporting a pump
max. 90 °
Fig. 2: Transporting a complete pump set
max. 90 °
Fig. 3: Transporting a pump on baseplate
3.2 Storage and preservation

If commissioning is to take place some time after delivery, we recommend that the
following measures be taken for pump (set) storage.
CAUTION
Damage during storage by humidity, dirt, or vermin
Corrosion/contamination of the pump (set)!
▷ For outdoor storage cover the pump (set) or the packaged pump (set) and
accessories with waterproof material.
RPH 13 of 68
CAUTION
Wet, contaminated or damaged openings and connections
Leakage or damage to the pump set!
▷ Only remove caps/covers from the openings of the pump set at the time of
installation.
Store the pump (set) in a dry, protected room where the atmospheric humidity is as
constant as possible.
Rotate the shaft by hand once a month, e.g. via the motor fan.
If properly stored indoors, the pump set is protected for a maximum of 12 months.
New pumps/pump sets are supplied by our factory duly prepared for storage.
For storing a pump (set) which has already been operated, observe the instructions in
(⇨ Section 6.3.1 Page 38) .
3.3 Return to supplier

1. Drain the pump as per operating instructions. (⇨ Section 7.3 Page 44)
2. Always flush and clean the pump, particularly if it has been used for handling
noxious, explosive, hot or other hazardous fluids.
3. If the fluids handled by the pump leave residues which might lead to corrosion
damage when coming into contact with atmospheric humidity, or which might
ignite when coming into contact with oxygen, the pump set must also be
neutralised, and anhydrous gas must be blown through the pump for drying
purposes.
4. Always complete and enclose a certificate of decontamination when returning
the pump (set). (⇨ Section 11 Page 66)
Always indicate the safety and decontamination measures taken.
NOTE
If required, a blank certificate of decontamination can be downloaded from the KSB web
site at: www.ksb.com/certificate_of_decontamination
3.4 Disposal
WARNING
Fluids posing a health hazard
Hazardous to persons and the environment!
▷ Collect and properly dispose of flushing liquid and any fluid residues.
▷ Wear safety clothing and a protective mask, if required.
▷ Observe all legal regulations on the disposal of fluids posing a health hazard.
1. Dismantle the pump (set).

Collect greases and other lubricants during dismantling.
2. Separate and sort the pump materials, e.g. by:
- Metals
- Plastics
- Electronic waste
- Greases and other lubricants
3. Dispose of materials in acc. with local regulations or in another controlled
manner.
14 of 68 RPH
4 Description of the Pump (Set)
4.1 General description

▪ Process pump to API 610
Pump for handling the large variety of crude oil products in refineries as well as in
the chemical and petrochemical industry.
4.2 Designation
Example: RPH H - S1 I 80-280 B
Table 5: Key to the designation
Code Description
RPH Type series
H Heatable model
S1 Material variant to API 610.
I Version with auxiliary impeller (inducer)
80 Nominal discharge nozzle diameter [mm]
280 Nominal impeller diameter [mm]
B Special hydraulics (B-hydraulics)
4.3 Name plate
Aktiengesellschaft
16
67225 Frankenthal 1
Ord.-No. 997186942100630001 Year 2008 2
15
14 Ser.-No. Type RPH 100-280 3
13 Item-No. 107-P-102B Test press.ure 7200 kPa 4
12 Q 110 m3/h H 70,00 m 5
11 n 2950 1/min t 60 °C 6
10 ρ 0,51 kg/dm3 MAWP 4800/85 kPa@°C
Shaft seal H75VK/85-PTA80
Bearings NU 213C3/2 * 7311BMUA
Impeller∅ mm max. min. rated
standard / 1st stage 295 230 243
Ident-No 00380 249
2nd stage
ZN 3823 - E 13
9 8 7
Fig. 4: Name plate
1 Year of construction 2 Type series/pump size

3 Test pressure 4 Head
5 Application temperature 6 Maximum application
pressure@temperature
7 Impeller diameter when installed 8 Minimum impeller diameter
9 Maximum impeller diameter 10 Bearings
11 Shaft seal 12 Density of the fluid handled
13 Rated speed 14 Flow rate
15 Item number 16 KSB order number
4.4 Design details

Design
▪ Volute casing pump
▪ Horizontal installation
RPH 15 of 68
▪ Back pull-out design

▪ Single-stage
▪ Fulfills technical requirements to API3) 610, 10th edition/ISO 13709
Pump casing
▪ Volute casing with integrally cast pump feet
▪ Centreline pump feet
▪ Single or double volute, depending on the pump size
▪ Radially split volute casing
▪ Axial inlet nozzle, tangential discharge nozzle pointing vertically upwards.
(From DN 250 / from impeller diameter 500 / pump size 200-401: radial discharge
nozzle pointing vertically upwards)
▪ Volute casing with casing wear ring
▪ Casing cover (with casing wear ring, as required)
Optional:
▪ Casing cover with heating and/or cooling chamber, as required
Impeller type
▪ Closed radial impeller
▪ Impeller with impeller wear ring on the suction side
(if required also on the discharge side).
▪ Sealing gap and balancing holes balance axial forces
Shaft seal
▪ Cartridge seal to API4) 682
NOTE
Seal designs and types other than specified herein shall only be used in exceptional
cases and only after prior consultation with the manufacturer.
Bearings
▪ Uncooled
Optional:
▪ Cooled bearing bracket
Design specifications Motor-end bearing:
▪ Fixed bearing
▪ Paired angular contact ball bearing
▪ Axial movement of the rotor limited to maximum 0.5 mm
▪ Oil bath lubrication
▪ Optional: Oil mist lubrication
Pump-end bearing:
▪ Radial bearing
▪ Cylindrical roller bearing
▪ Absorbs radial loads only
▪ Oil bath lubrication
▪ Optional: Oil mist lubrication
Bearing bracket Example: B03
designation
3) American Petroleum Institute

4) American Petroleum Institute
16 of 68 RPH
Table 6: Bearing bracket designation

Designation Description
B Back pull-out bearing bracket
03 Size code (based on dimensions of seal chamber, shaft end
and bearings)
Refer to the data sheet to find your bearing design.

Bearings used Table 7: Bearing design
KSB designation FAG designation SKF designation
B.MUA B-MP-UA BECBM
Table 8: Standard bearing assembly

Bearing bracket Rolling element bearing
Pump end Motor end
B02 NU211C3 2 x 7309B-MUA
B03 NU213C3 2 x 7311B-MUA
B05 NU316C3 2 x 7315B-MUA
B06 NU324C3 2 x 7224B-MUA
B07 NU324C3 2 x 7324B-MUA
Table 9: Reinforced bearing assembly (triple bearing assembly)

Bearing bracket Rolling element bearing
Pump end Motor end
B02 NU211C3 3 x 7309B-MUA
B03 NU213C3 3 x 7311B-MUA
B05 NU316C3 3 x 7315B-MUA
B06 NU324C3 3 x 7224B-MUA
B07 NU324C3 3 x 7324B-MUA
4.5 Design and function

1 2 3 4 5
6 7 8 9 10
1 Clearance gap 2 Discharge nozzle

3 Casing cover 4 Shaft
5 Bearing bracket 6 Suction nozzle
7 Impeller 8 Shaft seal
9 Rolling element bearing, pump end 10 Rolling element bearing, motor
end
RPH 17 of 68
Design The pump is designed with an axial fluid inlet and a radial or tangential outlet. The
hydraulic system runs in its own bearings and is connected to the motor by a shaft
coupling.
Function The fluid enters the pump axially via a suction nozzle (6) and is accelerated by the
rotating impeller (7), which causes a cylindrical flow towards the outside of the
pump. The flow profile of the pump casing converts the kinetic energy of the fluid
into pressure energy. The fluid is pumped to the discharge nozzle (2), where it leaves
the pump. The clearance gap (1) prevents any fluid from flowing back from the
pump casing into the inlet. At the rear side of the impeller, the shaft (4) enters the
casing via the casing cover (3). The shaft passage through the pump casing is sealed
towards the atmosphere with a shaft seal (8). The shaft runs in rolling element
bearings (9 and 10), which are supported by a bearing bracket (5) and linked with the
casing cover.
Sealing The pump is sealed by a standardised mechanical seal.
4.6 Noise characteristics

Table 10: Surface sound pressure level LpA5) 6)
Rated Pump Pump set
power 2900 rpm 1450 rpm 960 rpm 2900 rpm 1450 rpm 960 rpm
input 760 rpm 760 rpm
PN[kW] [dB] [dB] [dB] [dB]
[dB] [dB]
1 54 53 52 63 58 56
2 56 55 53 66 60 58
3 57 56 55 68 62 60
4 59 58 56 69 63 61
6 61 59 58 71 65 62
8 62 61 59 72 66 64
11 64 63 61 74 68 65
15 66 65 63 75 69 67
19 67 66 64 76 70 68
22 68 67 65 77 71 68
30 70 68 66 78 72 70
37 71 70 67 79 73 70
45 72 71 68 80 74 71
55 73 72 69 80 74 72
75 75 73 71 81 76 73
90 76 74 71 82 76 73
110 77 75 72 82 77 74
132 78 76 73 83 77 75
160 79 77 74 84 78 75
200 80 78 75 84 79 76
250 81 79 - 85 80 -
4.7 Scope of supply

Depending on the model, the following items are included in the scope of supply:
▪ Pump
Coupling ▪ Rigid multiple-disc clutch with spacer sleeve
Contact guard ▪ Coupling guard to EN 294
5) Spatial average; as per ISO 3744 and EN 12639; valid for operating range Q/Qopt = 0.8 - 1.1 and non-cavitating pump
operation. If noise levels are to be guaranteed: Add +3 dB for measuring and constructional tolerance.
6) Increase for 60 Hz operation: 3500 rpm+3 dB; 1750 rpm +1 dB; 1160 rpm:±0 dB
18 of 68 RPH
Baseplate ▪ Welded baseplate for the complete unit (pump and motor), in torsion-resistant
design
Special accessories ▪ As required
4.8 Dimensions and weights

For dimensions and weights please refer to the general arrangement drawing/outline
drawing of the pump (set).
RPH 19 of 68
5 Installation at Site
5.1 Safety regulations
DANGER
Improper installation in potentially explosive atmospheres
Explosion hazard!
Damage to the pump set!
▷ Comply with the applicable local explosion protection regulations.
▷ Observe the information in the data sheet and on the name plates of pump and
motor.
5.2 Checking the site before installation

Place of installation
WARNING
Installation on foundations which are unsecured and cannot support the load
Personal injury and damage to property!
▷ Make sure the foundation concrete is of sufficient strength (min. X0 to
DIN 1045).
▷ Only place the pump set on a foundation whose concrete has set firmly.
▷ Only place the pump set on a horizontal and level surface.
▷ Refer to the weights given in the general arrangement drawing.
1. Check the structural requirements.

All structural work required must have been prepared in accordance with the
dimensions stated in the outline drawing/general arrangement drawing.
5.3 Installing the pump set

Always install the pump set in horizontal position.
DANGER
Excessive temperatures due to improper installation
Explosion hazard!
▷ Install the pump in horizontal position to ensure self-venting of the pump.
5.3.1 Installation on a foundation

2
1
3 4
Fig. 5: Fitting the shims
1 Bolt-to-bolt clearance 2 Shim

3 Shim if clearance > 800 mm 4 Foundation bolt
✓ The foundation has the required strength and characteristics.
20 of 68 RPH
✓ The foundation has been prepared in accordance with the dimensions stated on
the outline drawing / general arrangement drawing.
1. Position the pump on the foundation and use a spirit level to align shaft and
discharge nozzle.
Permissible deviation: 0.2 mm/m.
2. If required, use shims (2) to adjust the height.
Fit shims between the baseplate/foundation frame and the foundation itself;
always insert them to the left and right of the foundation bolts and in close
proximity to these bolts.
For a bolt-to-bolt clearance > 800 mm, insert additional shims halfway between
the adjoining holes.
All shims must lie perfectly flush.
3. Insert the foundation bolts (4) into the holes provided.
4. Use concrete to set the foundation bolts (4) into the foundation.
5. Wait until the concrete has set firmly, then align the baseplate.
6. Tighten the foundation bolts (4) evenly and firmly.
7. Grout the baseplate using low-shrinkage concrete with a standard particle size
and a water/concrete ratio of ≤ 0.5.
Produce flowability with the help of a solvent.
Perform secondary treatment of the concrete to DIN 1045.
NOTE
For low-noise operation the pump set can be mounted on vibration dampers upon
confirmation by the manufacturer. In this case, only fasten the flexible elements at the
baseplate after the piping has been connected.
NOTE
Expansion joints can be fitted between pump and suction/discharge line.
5.4 Piping
5.4.1 Connecting the piping
DANGER
Excessive loads acting on the pump nozzles
Danger to life from leakage of hot, toxic, corrosive or flammable fluids!
▷ Do not use the pump as an anchorage point for the piping.
▷ Anchor the pipelines in close proximity to the pump and connect them without
transmitting any stresses or strains.
▷ Observe the permissible forces and moments at the pump nozzles. (⇨ Section
5.4.2 Page 23)
▷ Take appropriate measures to compensate thermal expansion of the piping.
CAUTION
Incorrect earthing during welding work at the piping
Destruction of rolling element bearings (pitting effect)!
▷ Never earth the electric welding equipment on the pump or baseplate.
▷ Prevent current flowing through the rolling element bearings.
RPH 21 of 68
NOTE
It is recommended to install check and shut-off elements in the system, depending on the
type of plant and pump. However, such elements must not obstruct proper drainage or
hinder disassembly of the pump.
✓ The suction lift line/suction head line has been laid with a rising/downward slope
towards the pump.
✓ The nominal diameters of the pipelines are at least equal to the nominal
diameters of the pump nozzles.
✓ To prevent excessive pressure losses, adapters to larger diameters have a diffuser
angle of approximately 8°.
✓ The pipelines have been anchored in close proximity to the pump and connected
without transmitting any stresses or strains.
1. Thoroughly clean, flush and blow through all vessels, pipelines and connections
(especially of new installations).
2. Before installing the pump in the piping, remove the flange covers on the suction
and discharge nozzles of the pump.
CAUTION
Welding beads, scale and other impurities in the piping
Damage to the pump!
▷ Free the piping from any impurities.
▷ If necessary, install a filter.
▷ Observe the instructions in (⇨ Section 7.2.2.3 Page 42).
3. If required, install a filter in the piping (see drawing: Filter in the piping).
1
2
Fig. 6: Filter in the piping
1 Differential pressure gauge 2 Filter
NOTE
Use a filter with laid-in wire mesh (mesh width 0.5 mm, wire diameter 0.25 mm) of
corrosion-resistant material.
Use a filter three times the diameter of the piping.
Conical filters have proved suitable.
4. Connect the pump nozzles with the piping.
CAUTION
Aggressive flushing and pickling agents
Damage to the pump!
▷ Match the cleaning operation mode and duration for flushing and pickling
service to the casing and seal materials used.
22 of 68 RPH
5.4.2 Permissible forces and moments at the pump nozzles
Fz Fz
RPH pumps are designed to withstand
Fy Fy Mz twice the piping forces and moments
My required by API 610, tables 2-1A and 2-1B.
Fx Fx Mx
Fz
Fy
Fx
Table 11: Forces and moments at the pump nozzles

Suction nozzle Discharge nozzle
Pump size
Forces Moments Forces Moments

[N] [Nm] [N] [Nm]
Fx Fy Fz Fres Mx My Mz Mres Fx Fy Fz Fres Mx My Mz Mres
25-180 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
25-230 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-180 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-230 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-280 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-181 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-231 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-281 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
40-361 1780 1430 1160 2560 920 460 710 1250 1430 1160 1780 2560 920 460 710 1250
50-180 2670 2140 1780 3860 1900 950 1440 2570 1430 1160 1780 2560 920 460 710 1250
50-230 2670 2140 1780 3860 1900 950 1440 2570 1430 1160 1780 2560 920 460 710 1250
50-280 2670 2140 1780 3860 1900 950 1440 2570 1430 1160 1780 2560 920 460 710 1250
50-360 2670 2140 1780 3860 1900 950 1440 2570 1430 1160 1780 2560 920 460 710 1250
50-450 2670 2140 1780 3860 1900 950 1440 2570 1430 1160 1780 2560 920 460 710 1250
80-180 3560 2840 2320 5110 2660 1360 2010 3600 2140 1780 2670 3860 1900 950 1440 2570
80-230 3560 2840 2320 5110 2660 1360 2010 3600 2140 1780 2670 3860 1900 950 1440 2570
80-280 3560 2840 2320 5110 2660 1360 2010 3600 2140 1780 2670 3860 1900 950 1440 2570
80-360 3560 2840 2320 5110 2660 1360 2010 3600 2140 1780 2670 3860 1900 950 1440 2570
80-450 3560 2840 2320 5110 2660 1360 2010 3600 2140 1780 2670 3860 1900 950 1440 2570
100-180 6230 4980 4090 8960 4610 2360 3530 6270 2850 2310 3560 5110 2660 1360 2010 3600
100-230 6230 4980 4090 8960 4610 2360 3530 6270 2850 2310 3560 5110 2660 1360 2010 3600
100-280 6230 4980 4090 8960 4610 2360 3530 6270 2850 2310 3560 5110 2660 1360 2010 3600
100-360 6230 4980 4090 8960 4610 2360 3530 6270 2850 2310 3560 5110 2660 1360 2010 3600
100-450 6230 4980 4090 8960 4610 2360 3530 6270 2850 2310 3560 5110 2660 1360 2010 3600
150-230 9790 7560 6230 13850 7050 3530 5150 9420 4980 4100 6230 8970 4610 2360 3530 6270
150-280 9790 7560 6230 13850 7050 3530 5150 9420 4980 4100 6230 8970 4610 2360 3530 6270
150-360 9790 7560 6230 13850 7050 3530 5150 9420 4980 4100 6230 8970 4610 2360 3530 6270
150-450 9790 7560 6230 13850 7050 3530 5150 9420 4980 4100 6230 8970 4610 2360 3530 6270
150-501 9790 7560 6230 13850 7050 3530 5150 9420 4980 4100 6230 8970 4610 2360 3530 6270
150-630 9790 7560 6230 13850 7050 3530 5150 9420 4980 4100 6230 8970 4610 2360 3530 6270
200-280 13350 10680 8900 19270 10030 4880 7590 13490 7560 6230 9790 13850 7060 3530 5150 9420
200-360 13350 10680 8900 19270 10030 4880 7590 13490 7560 6230 9790 13850 7060 3530 5150 9420
200-401 13350 10680 8900 19270 10030 4880 7590 13490 7560 6230 9790 13850 7060 3530 5150 9420
200-450 13350 10680 8900 19270 10030 4880 7590 13490 7560 6230 9790 13850 7060 3530 5150 9420
200-501 13350 10680 8900 19270 10030 4880 7590 13490 7560 6230 9790 13850 7060 3530 5150 9420
200-670 13350 10680 8900 19270 10030 4880 7590 13490 7560 6230 9790 13850 7060 3530 5150 9420
250-401 16000 13340 10680 23410 12200 5960 9220 16412 10680 8900 13340 19268 10040 4880 7600 13505
RPH 23 of 68
Suction nozzle Discharge nozzle

Pump size Forces Moments Forces Moments
[N] [Nm] [N] [Nm]
Fx Fy Fz Fres Mx My Mz Mres Fx Fy Fz Fres Mx My Mz Mres
250-501 16000 13340 10680 23410 12200 5960 9220 16412 10680 8900 13340 19267 10040 4880 7600 13505
250-630 16000 13340 10680 23410 12200 5960 9220 16412 10680 8900 13340 19267 10040 4880 7600 13505
250-710 16000 13340 10680 23410 12200 5960 9220 16412 10680 8900 13340 19267 10040 4880 7600 13505
300-400 17800 14240 11560 25560 12740 6240 9500 17080 13340 10680 16000 23400 12200 5960 9220 16420
300-500 17800 14240 11560 25560 12740 6240 9500 17080 13340 10680 16000 23400 12200 5960 9220 16420
300-630 17800 14240 11560 25560 12740 6240 9500 17080 13340 10680 16000 23400 12200 5960 9220 16420
350-400 17800 14240 11560 25560 12740 6240 9500 17080 14240 11560 17800 25560 12740 6240 9500 17080
350-500 17800 14240 11560 25560 12740 6240 9500 17080 14240 11560 17800 25560 12740 6240 9500 17080
350-650 20460 16900 13340 29700 14640 7340 10840 19640 14240 11560 17800 25560 12740 6240 9500 17080
350-710 20460 16900 13340 29700 14640 7340 10840 19640 14240 11560 17800 25560 12740 6240 9500 17080
400-504 20460 16900 13340 29700 14640 7340 10840 19640 16900 13340 20460 29700 14640 7340 10840 19640
400-506 20460 16900 13340 29700 14640 7340 10840 19640 16900 13340 20460 29700 14640 7340 10840 19640
400-710 20460 16900 13340 29700 14640 7340 10840 19640 16900 13340 20460 29700 14640 7340 10840 19640
5.4.3 Auxiliary connections
CAUTION
Failure to use or incorrect use of auxiliary connections (e.g. barrier fluid, flushing liquid,
etc.)
Malfunction of the pump!
▷ Refer to the general arrangement drawing, the piping layout and pump
markings (if any) for the dimensions and locations of auxiliary connections.
▷ Use the auxiliary connections provided.
5.5 Protective equipment
WARNING
The volute casing and casing/discharge cover take on the same temperature as the fluid
handled
Risk of burning!
▷ Insulate the volute casing.
▷ Fit protective equipment.
DANGER
An explosive atmosphere forms due to insufficient venting
Explosion hazard!
▷ Make sure the space between the casing cover/discharge cover and the bearing
cover is sufficiently vented.
▷ Never close or cover the perforation of the bearing bracket guards (e.g. by
insulation).
CAUTION
Heat build-up in the bearing bracket
Damage to the bearing!
▷ Never insulate the casing cover and the bearing bracket.
24 of 68 RPH
5.6 Checking the coupling alignment

DANGER
Inadmissible temperatures at the coupling or bearings due to misalignment of the
coupling
Explosion hazard!
▷ Make sure that the coupling is correctly aligned at all times.
CAUTION
Misalignment of pump and motor shafts
Damage to pump, motor and coupling!
▷ Always check the coupling after the pump has been installed and connected to
the piping.
▷ Also check the coupling of pump sets supplied with pump and motor mounted
on the same baseplate.
Checking the coupling alignment with a dial gauge
Fig. 7: Checking the spacer-type coupling with a dial gauge

1. Mark the installation position of the coupling by dotting marks (balancing
condition).
2. Remove the coupling spacer.
NOTE
While the pump's coupling is disengaged, also check the direction of rotation. (⇨ Section
5.9 Page 27)
3. Check the alignment of the coupling halves with a dial gauge (see drawing
"Checking the spacer-type coupling with a dial gauge").
Admissible run-out of coupling face (axial) maximum 0.1 mm.
Admissible radial deviation, measured over the complete circumference,
maximum 0.2 mm.
5.7 Aligning the pump and motor

After having installed the pump set and connected the piping, check the coupling
alignment and, if required, re-align the pump set (with the motor).
Any differences in shaft centre height between the pump and the motor are
compensated by means of shims.
RPH 25 of 68
1
Fig. 8: Pump set with shim
1 Shim
✓ The coupling guard and step guard, if any, have been removed.
1. Check the coupling alignment.
2. Unscrew the hexagon head bolts at the motor.
3. Insert shims underneath the motor feet until the difference in shaft centre height
has been compensated.
4. Re-tighten the hexagon head bolts.
5. Check that the coupling and shaft can easily be rotated by hand.
WARNING
Unprotected rotating coupling
Risk of injury by rotating shafts!
▷ Always operate the pump set with a coupling guard.
If the customer specifically requests not to include a coupling guard in KSB's
delivery, then the operator must supply one!
▷ Observe all relevant regulations for selecting a coupling guard.
6. Reinstall the coupling guard and step guard, if any.
7. Check the distance between coupling and coupling guard.
The coupling guard must not touch the coupling.
DANGER
Risk of ignition by frictional sparks
Explosion hazard!
▷ Choose a coupling guard material that is non-sparking in the event of
mechanical contact (see DIN EN 13463-1).
5.8 Electrical connection

DANGER
Incorrect electrical installation
Explosion hazard!
▷ For electrical installation, also observe the requirements of IEC 60079-14.
▷ Always connect explosion-proof motors via a motor protection switch.
DANGER
Work on the pump set by unqualified personnel
Danger of death from electric shock!
▷ Always have the electrical connections installed by a trained electrician.
▷ Observe regulations IEC 30364 (DIN VDE 0100) and, for explosion-proof pump
sets, IEC 60079 (DIN VDE 0165).
26 of 68 RPH
WARNING
Incorrect connection to the mains
Damage to the mains network, short circuit!
▷ Observe the technical specifications of the local energy supply companies.
1. Check the available mains voltage against the data on the motor name plate.
2. Select an appropriate start-up method.
NOTE
It is recommended to fit a motor protection device.
5.8.1 Connecting the motor

NOTE
In compliance with DIN VDE 0530 - Part 8, three-phase motors are always wired for
clockwise rotation (looking at the motor shaft stub).
The pump's direction of rotation is indicated by an arrow on the pump.
1. Change the motor's direction of rotation to match that of the pump.

2. Observe the manufacturer's product literature supplied with the motor.
5.9 Checking the direction of rotation

DANGER
Temperature increase resulting from contact between rotating and stationary
components
Explosion hazard!
▷ Never check the direction of rotation by starting up the unfilled pump set.
▷ Separate the pump from the motor to check the direction of rotation.
WARNING
Hands or objects inside the pump casing
Risk of injuries, damage to the pump!
▷ Never insert your hands or any other objects into the pump.
▷ Check that the inside of the pump is free from any foreign objects.
CAUTION
Incorrect direction of rotation of model with auxiliary impeller (inducer)
Damage to the pump!
▷ Separate the pump from the motor to check the direction of rotation.
CAUTION
Motor and pump running in the wrong direction of rotation
Damage to the pump!
▷ Refer to the arrow indicating the direction of rotation on the pump.
▷ Check the direction of rotation. If required, interchange any two phases to
correct the direction of rotation.
The correct direction of rotation of motor and pump is in clock-wise direction (seen
from the motor end).
1. Start the pump set and stop it again immediately to determine the motor's
direction of rotation.
RPH 27 of 68
2. Check the direction of rotation.

The motor's direction of rotation must match the arrow indicating the direction
of rotation on the pump.
3. If the direction of rotation is incorrect, check the connection of the motor and
the switchgear, if any.
28 of 68 RPH
6 Commissioning/Start-up/Shutdown
6.1 Commissioning/start-up
6.1.1 Prerequisites for commissioning/start-up
Before starting up the pump set make sure that the following requirements are met:
▪ The pump set has been properly connected to the electric power supply and is
equipped with all protection devices.
▪ The pump has been primed with the fluid to be handled. (⇨ Section 6.1.4 Page
31)
▪ The direction of rotation has been checked. (⇨ Section 5.9 Page 27)
▪ All auxiliary connections required are connected and operational.
▪ The lubricants have been checked.
▪ After prolonged shutdown of the pump (set), the activities described in (⇨
Section 6.4 Page 38) have been carried out.
6.1.2 Filling in the lubricant

Oil-lubricated bearings Fill the bearing bracket with lubricating oil.
▪ Oil quality (⇨ Section 7.2.3.1.2 Page 43)
▪ Oil quantity (⇨ Section 7.2.3.1.3 Page 43)
NOTE
On uncooled bearing brackets, first remove the reservoir of the constant-level oiler. Then
screw in the connection elbow separately.
Filling the constant-level oiler with lubricating oil (oil bath

lubricated bearings only)
✓ The constant-level oiler is screwed into the upper tapping hole of the bearing
bracket.
NOTE
If no constant-level oiler is provided on the bearing bracket, the oil level can be read in
the middle of the oil level sight glass arranged at the side of the bearing bracket.
CAUTION
Insufficient lubricating oil in the reservoir of the constant-level oiler
Damage to the bearings!
▷ Regularly check the oil level.
▷ Always fill the oil reservoir completely.
▷ Keep the oil reservoir properly filled at all times.
RPH 29 of 68
1 2
3 4 5
Fig. 9: Bearing bracket with constant-level oiler
1 Constant-level oiler 2 Vent plug

3 Connection elbow of constant-level 4 Screwed plug
oiler
5 Bearing bracket
1. Remove the protective cage.
2. Unscrew the vent plug (2).
3. Hinge down the reservoir of the constant-level oiler (1) from the bearing bracket
(5) and hold in this position.
4. Pour in the oil through the vent plug tapping hole until oil appears in the
connection elbow of the constant-level oiler (3).
5. Fill the reservoir of the constant-level oiler (1) with oil up to the maximum level.
6. Snap the reservoir of the constant-level oiler (1) back into operating position.
7. Screw the vent plug (2) back in.
8. Fit the protective cage.
9. After approximately 5 minutes, check the oil level in the reservoir of the
constant-level oiler (1).
It is important to keep the reservoir properly filled at all times, to ensure an
optimum oil supply. Repeat steps 1 - 8, if necessary.
10. To verify the correct function of the constant-level oiler (1), slowly drain oil
through the drain plug (4) until air bubbles can be seen in the oiler.
NOTE
An excessively high oil level can lead to a temperature rise and to leakage of the fluid
handled or oil.
30 of 68 RPH
Connecting the oil mist lubrication (for oil mist lubrication only)
Bearings with oil mist
lubrication
Fig. 10: Oil mist lubrication

✓ Always observe the instructions of the lubricating system manufacturer
(especially on dosing and oil quantity).
1. Remove plugs 916.N3.
2. Connect the lines of the oil mist lubricating system.
3. Remove drain plug 916.46.
4. Connect the drain line (returning the oil back into the oil mist system).
5. Close plug 916.N1.
6.1.3 Shaft seal
Shaft seals are fitted prior to delivery.

Observe the instructions on dismantling (⇨ Section 7.4.6 Page 46) or reassembly (⇨
Section 7.5.3 Page 49) .
Reservoir of non- If applicable, fill the reservoir of non-pressurised external fluid in accordance with
pressurised external fluid the general arrangement drawing.
Double-acting mechanical Prior to starting up the pump, apply barrier pressure as specified in the general
seal arrangement drawing.
External liquid feed Apply the quantities and pressures specified in the data sheet and the general
arrangement drawing.
6.1.4 Filling and venting the pump
DANGER
An explosive atmosphere forms inside the pump
Explosion hazard!
▷ The pump internals in contact with the fluid to be handled, including the seal
chamber and auxiliary systems must be filled with the fluid to be handled at all
times.
▷ Provide sufficient inlet pressure.
▷ Provide an appropriate monitoring system.
RPH 31 of 68
DANGER
Shaft seal failure caused by dry running
Hot or toxic fluid could escape!
Damage to the pump!
▷ Before starting up the pump set, vent the pump and suction line and fill both
with the fluid to be handled.
1. Vent the pump and suction line and fill both with the fluid to be handled.
2. Fully open the shut-off element in the suction line.
3. Fully open all auxiliary connections (barrier fluid, flushing liquid, etc).
6.1.5 Final check

1. Remove the coupling guard and step guard, if any.
2. Check the coupling alignment; re-align the coupling, if required.
3. Check that the coupling and shaft can easily be rotated by hand.
4. Re-install the coupling guard and step guard, if any.
5. Check the distance between coupling and coupling guard.
The coupling guard must not touch the coupling.
6.1.6 Water cooling

CAUTION
Deposit forming, aggressive cooling water
Damage to the pump!
▷ Observe the cooling water quality.
Observe the following quality data of the cooling water:
▪ Not deposit forming
▪ Not aggressive
▪ Free from suspended solids
▪ Hardness on average 5 °dH (~1mmol/l)
▪ pH > 8
▪ Conditioned and neutral with regard to mechanical corrosion
▪ Inlet temperature tE= 10 to 30 °C
Outlet temperature tA= maximum 45 °C
6.1.7 Cooling of the pump

The casing cover, the bearing bracket and the casing support on the baseplate can be
cooled.
Observe the following quality data of the cooling water:
▪ Maximum permissible cooling liquid pressure: 10 bar
▪ Maximum permissible cooling liquid test pressure: 15 bar
▪ Observe the specified cooling liquid quantity.
32 of 68 RPH
6.1.8 Cooling of the shaft seal

CAUTION
The vaporisation pressure of the fluid handled is higher than the atmospheric pressure
Damage to the shaft seal/pump!
▷ Cool the shaft seal.
▷ Provide sufficient quantities of cooling liquid (see table).
NOTE
The vaporisation pressure varies depending on the fluid handled, the system pressure
and the material of the shaft seal (e.g. hot water).
Table 12: Cooling liquid quantities:

Fluid temperature Cooling liquid quantities
[°C] [m3/h]7)
Casing cover < 250 0,3
< 400 0,6
Bearing bracket 200 /250 to 3159)
8) 0.2
> 31510)
Support on baseplate > 250 0.2
6.1.8.1 Cooling of the heat exchanger
For mechanical seals with product circulation observe the following for the heat
exchanger:
Table 13: Cooling liquid quantity depending on the bearing bracket
At speed n Cooling liquid
[m3/h]
[rpm] Bearing bracket
B02 B03 B05 B06 B07
1750/1450 0.35 0.5 0.6 0.8 0.8
3500/2900 1.2 1.2 1.8 - -
6.1.9 Heating
DANGER
Excessive surface temperature
Explosion hazard!
Burns!
▷ Observe the permissible temperature classes. (⇨ Section 2.10.2 Page 11)
CAUTION
Time for warming up the pump too short
Damage to the pump!
▷ Check that the pump is sufficiently warmed up throughout.
The casing cover can be heated with hot water or steam. Observe the following data
for the heating medium:
7) The cooling liquid quantities indicated are based on Δt = max. 15 °C.

8) For n = 3500 rpm and n = 2900 rpm in conjunction with triple bearing assembly. In all other cases from 250 °C!
9) Water cooling or fan wheel
10) Water cooling (and fan wheel optional)
RPH 33 of 68
▪ Maximum permissible temperature t = 150 °C

▪ Maximum permissible pressure p = 10 bar
▪ Seal casing cover with O-rings made of EP.
CAUTION
Lack of heating medium
Damage to the pump!
▷ Provide sufficient quantities of a suitable heating medium.
6.1.10 Heating up/keeping warm the pump (set)
CAUTION
Pump blockage
Damage to the pump!
▷ Prior to pump start-up, heat up the pump as described in the manual.
Observe the following when heating up the pump (set) and keeping it warm:
▪ Make sure the temperature is increased continuously.
▪ Max. heating speed: 10 °C/min (10 K/min)
Fluid temperatures above If the pump is used for handling fluids with fluid temperatures exceeding 150 °C,
150 °C make sure that the pump has been heated throughout before starting it up.
Temperature difference The temperature difference between the pump's surface and the fluid handled must
not exceed 100 °C (100 K) when the pump is started up.
6.1.11 Start-up
DANGER
The permissible pressure and temperature limits will be exceeded if the pump is
operated with the suction and discharge lines closed.
Explosion hazard!
Leakage of hot or toxic fluids!
▷ Never operate the pump with the shut-off elements in the suction line and/or
discharge line closed.
▷ Only start up the pump set with the discharge side gate valve slightly or fully
open.
DANGER
Excessive temperatures due to dry running or excessive gas content in the fluid handled
Explosion hazard!
▷ Never operate the pump set without liquid fill.
▷ Prime the pump as specified. (⇨ Section 6.1.4 Page 31)
▷ Always operate the pump within the permissible operating range.
CAUTION
Abnormal noises, vibrations, temperatures or leakage
Damage to the pump!
▷ Switch off the pump (set) immediately.
▷ Eliminate the causes before returning the pump set to service.
✓ The piping system connected to the pump set has been cleaned.
✓ Pump, suction line and inlet tank, if any, have been vented and filled with the
fluid to be pumped.
34 of 68 RPH
✓ The filling and venting lines have been closed.
CAUTION
Start-up against open discharge line
Overloading of the motor!
▷ Use a soft starter.
▷ Use speed control.
▷ Make sure the power reserve of the motor is sufficient.
1. Fully open the shut-off valve in the suction head/suction lift line.
2. Close or slightly open the shut-off valve in the discharge line.
3. Switch on the motor.
4. Immediately after the pump has reached full rotational speed, slowly open the
shut-off valve in the discharge line and adjust it to comply with the duty point.
DANGER
Seal leakage at operating temperature
Hot or toxic fluid may escape!
▷ Once the operating temperature has been reached, re-tighten the hexagon nuts
at the casing/discharge cover.
▷ Check the coupling alignment. Re-align the coupling if required.
5. When the operating temperature has been reached and/or in the event of
leakage, switch off the pump set and let it cool down. Then retighten the bolts
between lantern and casing.
6. Check the coupling alignment and re-align the coupling if required.
6.1.12 Checking the shaft seal
Mechanical seal The mechanical seal only leaks slightly or invisibly (as vapour) during operation.
Mechanical seals are maintenance-free.
6.1.13 Shutdown
✓ The shut-off element in the suction line is and remains open.
✓ On pump sets with double-acting mechanical seal, apply the required pressure
specified in the general arrangement drawing to the mechanical seal chamber
also during standstill.
✓ Also ensure quench liquid supply during pump standstill.
1. Close the shut-off element the discharge line.
2. Switch off the motor and make sure the pump set runs down smoothly to a
standstill.
NOTE
If the discharge line is equipped with a non-return or check valve, the shut-off element
may remain open if there is back pressure.
NOTE
If shut-off is not possible, the pump will run in reverse direction.
The reverse runaway speed must be lower than the rated speed.
For prolonged shutdown periods:

1. Close the shut-off element in the suction line.
2. Close the auxiliary connections.
If the fluid to be pumped is fed in under vacuum, also supply the shaft seal with
RPH 35 of 68
barrier fluid during standstill.

Only turn off the cooling liquid supply after the pump has cooled down.
CAUTION
Risk of freezing during prolonged pump shutdown periods
Damage to the pump!
▷ Drain the pump and the cooling/heating chambers (if any) or otherwise protect
them against freezing.
6.2 Operating limits
DANGER
Non-compliance with application limits for pressure, temperature and speed
Explosion hazard!
Hot or toxic fluid may escape!
▷ Comply with the operating data indicated in the data sheet.
▷ Avoid prolonged operation against a closed shut-off valve.
▷ Never operate the pump at temperatures exceeding those specified in the data
sheet or on the name plate unless the written consent of the manufacturer has
been obtained.
6.2.1 Ambient temperature
Observe the following parameters and values during operation:

Table 14: Permissible ambient temperatures
Permissible ambient temperature Temperature
Maximum 43 °C
Minimum See data sheet
CAUTION
Operation outside the permissible ambient temperature
Damage to the pump (set)!
▷ Observe the specified limits for permissible ambient temperatures.
6.2.2 Frequency of starts
DANGER
Excessive surface temperature of the motor
Explosion hazard!
Damage to the motor!
▷ In case of explosion-proof motors, observe the switching frequency specified in
the manufacturer's product literature.
The frequency of starts is usually determined by the maximum temperature increase

of the motor. This largely depends on the power reserves of the motor in steady-
state operation and on the starting conditions (d.o.l., star-delta, moments of inertia,
etc). If the start-ups are evenly spaced over the period indicated, the following limits
can be used for orientation for start-up with the discharge-side gate valve slightly
open:
36 of 68 RPH
Table 15: Frequency of starts

Motor rating Maximum No. of start-ups
[kW] [Start-ups/hour]
up to 12 15
up to 100 10
more than 100 5
CAUTION
Re-start while motor is still running down
Damage to the pump (set)!
▷ Do not re-start the pump set before the pump rotor has come to a standstill.
6.2.3 Flow rate

Unless specified otherwise in the characteristic curves or in the data sheets, the
following applies:
Qmax11) see characteristic curves.
Qmin12) = 0.3xQopt13)
The data refer to water and water-like fluids. Longer operating periods with these
fluids and at the flow rates indicated will not cause an additional increase in the
temperatures on the pump surface. However, if the physical properties of the fluids
handled are different from water, the calculation formula below must be used to
check if an additional heat build-up may lead to a dangerous temperature increase at
the pump surface. If necessary, the minimum flow must be increased.
Table 16: Key

Symbol Description Unit
c Specific heat capacity J/kg K
g Gravitational constant m/s²
H Pump head m
Tf Temperature of the fluid handled °C
To Temperature at the casing surface °C
Pump efficiency at duty point -
Temperature difference °C
6.2.4 Density of the fluid handled

The power input of the pump increases in proportion to the density of the fluid
handled.
CAUTION
Excessive density of the fluid handled
Motor overload!
▷ Observe the information on fluid density indicated in the data sheet.
▷ Make sure the power reserve of the motor is sufficient.
11) Maximum permissible flow rate

12) Minimum permissible flow rate
13) Efficiency option
RPH 37 of 68
6.2.5 Abrasive fluids

Do not exceed the maximum permissible solids content specified in the data sheet.
When the pump handles fluids containing abrasive substances, increased wear of the
hydraulic system and the shaft seal are to be expected. In this case, reduce the
intervals commonly recommended for servicing and maintenance.
6.3 Shutdown/storage/preservation
6.3.1 Measures to be taken for shutdown

The pump (set) remains installed
✓ Sufficient fluid is supplied for the operation check run of the pump.
1. Start up the pump (set) regularly once a month or once every three months for
approximately five minutes during prolonged shutdown periods.
This will prevent the formation of deposits within the pump and the pump
intake area.
The pump (set) is removed from the pipe and stored
✓ The pump has been properly drained (⇨ Section 7.3 Page 44) and the safety
instructions for dismantling the pump have been observed. (⇨ Section 7.4.1 Page
45)
1. Spray-coat the inside wall of the pump casing, and in particular the impeller
clearance areas, with a preservative.
2. Spray the preservative through the suction and discharge nozzles.
It is advisable to then close the pump nozzles (e.g. with plastic caps or similar).
3. Oil or grease all blank parts and surfaces of the pump (with silicone-free oil and
grease, food-approved if required) to protect them against corrosion.
Observe any additional information provided. (⇨ Section 3.2 Page 13)
If the pump set is to be stored temporarily, only preserve the wetted components
made of low alloy materials. Commercially available preservatives can be used for this
purpose. Observe the manufacturer's instructions for application/removal.
Observe any additional instructions and information provided. (⇨ Section 3 Page 13)
6.4 Returning to service after storage

For returning the pump to service observe the sections on commissioning/start-up (⇨
Section 6.1 Page 29) and the operating limits (⇨ Section 6.2 Page 36) .
In addition, carry out all servicing/maintenance operations before returning the
pump (set) to service. (⇨ Section 7 Page 39)
WARNING
Failure to re-install or re-activate protective devices
Risk of personal injury from moving parts or escaping fluid!
▷ As soon as the work is complete, re-install and/or re-activate any safety-relevant
and protective devices.
NOTE
If the pump has been out of service for more than one year, replace all elastomer seals.
38 of 68 RPH
7 Servicing/Maintenance
7.1 Safety regulations

DANGER
Improperly serviced pump set
Explosion hazard!
▷ Service the pump set regularly.
▷ Prepare a maintenance schedule with special emphasis on lubricants, shaft seal
and coupling.
The operator ensures that all maintenance, inspection and installation work is
performed by authorised, qualified specialist personnel who are thoroughly familiar
with the manual.
WARNING
Pump set started up inadvertently
Risk of injury by moving parts!
▷ Always make sure the electrical connections are disconnected before carrying
out work on the pump set.
▷ Make sure that the pump set cannot be switched on accidentally.
WARNING
Fluids posing a health hazard or hot fluids
Risk of personal injury!
▷ Observe all relevant laws.
▷ When draining the fluid take appropriate measures to protect persons and the
environment.
▷ Decontaminate pumps handling fluids posing a health hazard.
A regular maintenance schedule will help avoid expensive repairs and contribute to
trouble-free, reliable operation of the pump (set) with a minimum of maintenance
expenditure and work.
NOTE
All maintenance, service and installation work can be carried out by KSB Service. Find
your contact in the attached "Addresses" booklet or on the Internet at www.ksb.com/
contact".
Never use force when dismantling and reassembling a pump set.
7.2 Servicing/inspection
7.2.1 Supervision of operation
DANGER
Excessive temperatures as a result of bearings running hot or defective bearing seals
Explosion hazard!
Fire hazard!
▷ Regularly check the lubricant level.
▷ Regularly check the rolling element bearings for running noises.
RPH 39 of 68
CAUTION
Increased wear due to dry running
▷ Never operate the pump set without liquid fill.
▷ Never close the shut-off element in the suction line and/or supply line during
pump operation.
CAUTION
Excessive fluid temperature
Damage to the pump!
▷ Prolonged operation against a closed shut-off element is not permitted (heating
up of the fluid).
▷ Observe the temperature limits in the data sheet and in the section on
Operating limits. (⇨ Section 6.2 Page 36)
While the pump is in operation, observe and check the following:

▪ The pump must run quietly and free from vibrations at all times.
▪ In case of oil lubrication, ensure the oil level is correct.
▪ Check the shaft seal. (⇨ Section 6.1.12 Page 35)
▪ Check the static seals for any leakage.
▪ Check the rolling element bearings for running noises.
Vibrations, noise and an increase in current input occurring during unchanged
operating conditions indicate wear.
▪ Check the correct functioning of any auxiliary connections.
▪ Cooling system
Take the pump out of service at least once year to thoroughly clean the cooling
system.
▪ Monitor the stand-by pump.
To make sure that the stand-by pumps are ready for operation, start them up
once a week.
▪ Keep the stand-by pump warm.
Observe the following conditions to make sure the stand-by pump is operational
and kept warm:
– All cooling points are in operation.
– The permissible nozzle forces and moments are not exceeded.
– In extreme cases, contact the manufacturer.
▪ Monitor the bearing temperature.
The bearing temperature must not exceed 90 °C (measured on the outside of the
bearing bracket).
CAUTION
Operation outside the permissible bearing temperature
Damage to the pump!
▷ The bearing temperature of the pump (set) must never exceed 90 °C (measured
on the outside of the bearing bracket).
40 of 68 RPH
7.2.2 Inspection work
DANGER
Excessive temperatures caused by friction, impact or frictional sparks
Explosion hazard!
Fire hazard!
▷ Regularly check the coupling guard, plastic components and other guards of
rotating parts for deformation and sufficient distance from rotating parts.
7.2.2.1 Checking the coupling

Check the flexible elements of the coupling. Replace these parts in due time if there
is any sign of wear.
7.2.2.2 Checking the clearance gaps

For checking the clearance gaps remove impeller 230, if required. (⇨ Section 7.4.5
Page 46).
If the clearance gap is larger than permitted (see the following table), replace casing
wear ring 502.01/502.02 and/or impeller wear ring 503.01/503.02.
The clearances given refer to the diameter.
Table 17: Clearances between impeller and casing / between impeller and casing cover
Pump size Inner nominal Clearance Minimum clearance Inner Casing wear Minimum
diameter of the gap gap nominal ring clearance
suction-side casing (standard) to API 610 diameter of (standard) gap
wear ring the to API 610
[mm] [mm] discharge- [mm]
(rounded) [mm]
side casing
[mm] wear ring
(rounded)
[mm]
25-180 70 0.5-0.05 0.30 70 0.5-0.05 0.30
25-230 70 0.5-0.05 0.30 70 0.5-0.05 0.30
40-180 80 0.5-0.050 0.33 80 0.5-0.05 0.33
40-230 80 0.5-0.05 0.33 80 0.5-0.05 0.33
40-280 85 0.6-0.05 0.33 120 0.6-0.05 0.40
40-181 95 0.6-0.05 0.35 95 0.6-0.05 0.35
40-231 95 0.6-0.05 0.35 95 0.6-0.05 0.35
40-281 95 0.6-0.05 0.35 120 0.6-0.05 0.40
40-361 95 0.6-0.05 0.35 165 0.6-0.05 0.45
50-180 120 0.6-0.05 0.40 120 0.6-0.05 0.40
50-230 120 0.6-0.05 0.40 120 0.6-0.05 0.40
50-280 120 0.6-0.05 0.40 120 0.6-0.05 0.40
50-360 120 0.6-0.05 0.40 165 0.6-0.05 0.45
50-450 120 0.6-0.05 0.40 195 0.7-0.08 0.48
80-180 135 0.6-0.05 0.43 135 0.6-0.05 0.43
80-230 135 0.6-0.05 0.43 135 0.6-0.05 0.43
80-280 135 0.6-0.05 0.43 135 0.6-0.05 0.43
80-360 135 0.6-0.05 0.43 165 0.6-0.05 0.45
80-450 135 0.6-0.05 0.43 195 0.7-0.08 0.48
100-180 165 0.6-0.05 0.45 165 0.6-0.05 0.45
100-230 165 0.6-0.05 0.45 165 0.6-0.05 0.45
RPH 41 of 68
Pump size Inner nominal Clearance Minimum clearance Inner Casing wear Minimum
diameter of the gap gap nominal ring clearance
suction-side casing (standard) to API 610 diameter of (standard) gap
wear ring the to API 610
[mm] [mm] discharge- [mm]
(rounded) [mm]
side casing
[mm] wear ring
(rounded)
[mm]
100-280 165 0.6-0.05 0.45 165 0.6-0.05 0.45
100-360 165 0.6-0.05 0.45 165 0.6-0.05 0.45
100-450 175 0.6-0.05 0.45 195 0.7-0.08 0.48
150-230 195 0.7-0.08 0.48 195 0.7-0.08 0.48
150-280 195 0.7-0.08 0.48 195 0.7-0.08 0.48
150-360 195 0.7-0.08 0.48 195 0.7-0.08 0.48
150-450 200 0.7-0.08 0.48 235 0.7-0.08 0.53
150-501 225 0.7-0.08 0.50 225 0.7-0.08 0.50
150-630 240 0.7-0.08 0.53 290 0.7-0.08 0.58
200-280 225 0.7-0.08 0.50 225 0.7-0.08 0.50
200-360 235 0.7-0.08 0.53 280 0.7-0.08 0.58
200-450 235 0.7-0.08 0.53 280 0.7-0.08 0.58
200-401 250 0.6-0.05 0.53 250 0.6-0.05 0.53
200-501 255 0.6-0.08 0.55 255 0.6-0.08 0.55
200-670 290 0.6-0.05 0.58 290 0.6-0.05 0.58
250-401 330 0.75-0.08 0.63 330 075-0.08 0.63
250-501 310 0.6-0.08 0.60 310 0.6-0.08 0.60
250-630 330 0.75-0.100 0.63 340 0.75-0.1 0.63
250-710 310 0.7-0.08 0.60 340 0.85-0.1 0.63
300-400 330 0.75-0.08 0.63 330 0.75-0.08 0.63
300-500 350 0.85-0.1 0.65 350 0.85-0.1 0.65
300-630 360 0.85-0.1 0.65 340 0.75-0.1 0.63
250-400A 380 0.85-0.1 0.68 340 0.85-0.1 0.63
350-400B 350 0.85-0.1 0.65 340 0.85-0.1 0.63
350-500 380 0.85-0.1 0.68 380 0.85-0.1 0.68
350-630 400 0.85-0.1 0.7 400 0.85-0.1 0.7
350-710 400 0.85-0.1 0.7 400 0.85-0.1 0.7
400-504 410 0.85-0.1 0.7 410 0.85-0.1 0.7
400-506 440 0.85-0.1 0.73 440 0.85-0.1 0.73
400-710 440 0.85-0.1 0.73 500 0.85-0.1 0.80
7.2.2.3 Cleaning filters
CAUTION
Insufficient inlet pressure due to clogged filter in the suction line
Damage to the pump!
▷ Monitor contamination of filter with suitable means (e.g. differential pressure
gauge).
▷ Clean filter in appropriate intervals.
42 of 68 RPH
7.2.3 Lubrication and lubricant change of rolling element bearings
DANGER
Excessive temperatures as a result of bearings running hot or defective bearing seals
Explosion hazard!
Fire hazard!
▷ Regularly check the condition of the lubricant.
7.2.3.1 Oil lubrication

The rolling element bearings are usually lubricated with mineral oil.
7.2.3.1.1 Intervals
Table 18: Oil change intervals
Temperature at the First oil change All subsequent oil
bearing changes14)
up to 70 ℃ After 300 operating hours After 8500 operating hours
70 °C - 80 °C After 300 operating hours After 4200 operating hours
80 °C - 90 °C After 300 operating hours After 2000 operating hours
7.2.3.1.2 Oil quality

Table 19: Oil quality
Designation Symbol to DIN Properties
51502
CLP46 lubricating oil □ Kinematic viscosity at 40 46±4 mm²/s
to DIN 51517 °C
or Flash point (to +175 ℃
HD 20W/20 SAE Cleveland)
Solidification point -15 ℃
(pour point)
Application Higher than
temperature15) permissible bearing
temperature
7.2.3.1.3 Oil quantity

Bearing bracket Oil quantity bearing bracket
[l]
B02 0.9
B03 1.8
B05 2.5
B06 5.7
B07 4.7
14) At least once a year

15) For ambient temperatures below -10 °C use a different suitable type of lubricating oil. Contact KSB.
RPH 43 of 68
7.2.3.1.4 Changing the oil
WARNING
Lubricants posing a health hazard
Risk to persons and the environment!
▷ When draining the lubricant take appropriate measures to protect persons and
the environment.
▷ Observe all legal regulations on the disposal of liquids posing a health hazard.
1 2 3
Fig. 11: Bearing bracket with constant-level oiler
1 Constant-level oiler 2 Screwed plug

3 Bearing bracket
✓ A suitable container for the used oil is on hand.
1. Place the container underneath the screwed plug.
2. Undo the screwed plug (2) at the bearing bracket (3) and drain the oil.
3. Once the bearing bracket (3) has been drained, re-insert and re-tighten the
screwed plug (2).
4. Re-fill with oil.
7.3 Drainage/disposal
WARNING
Fluids posing a health hazard
Hazardous to persons and the environment!
▷ Collect and properly dispose of flushing liquid and any fluid residues.
▷ Wear safety clothing and a protective mask, if required.
▷ Observe all legal regulations on the disposal of fluids posing a health hazard.
If the fluids handled by the pump (set) leave residues which might lead to corrosion
when coming into contact with atmospheric humidity, or which might ignite when
coming into contact with oxygen, the pump (set) must be flushed through,
neutralised, and blown through with anhydrous gas for drying purposes.
Use connection 6B to drain the fluid handled (see auxiliary connections).
44 of 68 RPH
7.4 Dismantling the pump set
7.4.1 General notes/Safety regulations
WARNING
Unqualified personnel performing work on the pump (set)
▷ Always have repair and maintenance work performed by specially trained,
qualified personnel.
WARNING
Hot surface
▷ Allow the pump set to cool down to ambient temperature.
Observe the general safety instructions and information. (⇨ Section 7 Page 39)
For any work on the motor, observe the instructions of the relevant motor
manufacturer.
For dismantling and reassembly refer to the general assembly drawing.
In case of damage you can always contact our service staff.
DANGER
Insufficient preparation of work on the pump (set)
▷ Properly shut down the pump set. (⇨ Section 6.1.13 Page 35)
▷ Close the shut-off elements in the suction and discharge line.
▷ Drain the pump and release the pump pressure. (⇨ Section 7.3 Page 44)
▷ Close any auxiliary connections.
▷ Allow the pump set to cool down to ambient temperature.
7.4.2 Preparing the pump set

1. Disconnect the power supply (e.g. at the motor).
2. Disconnect and remove all auxiliary pipework.
3. Remove the coupling guard.
4. Remove the coupling spacer, if any.
5. Drain the oil fill of oil-lubricated bearings. (⇨ Section 7.2.3.1.4 Page 44)
7.4.3 Dismantling the motor

NOTE
For pump sets with spacer-type couplings, the back pull-out unit can be removed while
the motor remains screwed to the baseplate.
1. Disconnect the motor from the power supply.

2. Unbolt the motor from the baseplate.
3. Shift the motor to separate it from the pump.
WARNING
Motor tipping over
Risk of squashing hands and feet!
▷ Suspend or support the motor to prevent it from tipping over.
RPH 45 of 68
7.4.4 Removing the back pull-out unit

✓ At pump sets without spacer-type coupling, the motor has been removed.
WARNING
Back pull-out unit tipping over
▷ Suspend or support the bearing bracket at the pump end.
1. If required, suspend or support bearing bracket 330 to prevent it from tipping
over.
2. Remove hexagon nut 920.01 at volute casing 102.
3. Use forcing screws 901.30 to pull the back pull-out unit out of volute casing 102.
4. Remove and dispose of joint ring 411.10.
5. Place the back pull-out unit on a clean and level surface.
7.4.5 Dismantling the impeller
7.4.5.1 Loosening the impeller — for bearing brackets B02 to B05

✓ The notes and steps stated in (⇨ Section 7.4.1 Page 45) to (⇨ Section 7.4.4 Page
46) have been observed/carried out.
✓ The back pull-out unit is kept in a clean and level assembly area.
1. Unscrew impeller nut 922.01 with threaded insert (right-hand thread).
2. Remove and dispose of joint ring 411.31, if any
3. Remove lockwasher 931.02.
7.4.5.2 Loosening the impeller — for bearing brackets B06 and B07
1. Unscrew and remove impeller hub cap 260 (right-hand thread).
2. Remove and dispose of joint ring 411.31.
3. Bend back lockwasher 931.02.
4. Remove impeller screw 906 with lockwasher 931.02 and disc 550.87.
7.4.5.3 Removing the impeller — for all bearing bracket sizes

✓ The notes and steps stated in (⇨ Section 7.4.1 Page 45) to (⇨ Section 7.4.5.1 Page
46) and (⇨ Section 7.4.5.2 Page 46) have been observed/carried out.
1. Remove impeller 230 with a puller.
2. Place impeller 230 on a clean and level surface.
3. Remove keys 940.01 from shaft 210.
4. If throttling bush 542.02 is fitted, undo grub screws 904.38.
5. Remove throttling bush 542.02, if any.
7.4.6 Removing the cartridge seal

1. If assembling jigs are provided, loosen the hexagon head bolts for fitting the
assembling jigs.
46 of 68 RPH
2. Engage assembling jigs, if any, in the groove of shaft protecting sleeve 524.01
and re-tighten the hexagon head bolts.
3. Loosen hexagon head bolts 920.15 at casing cover 161.
4. Use forcing screws 901.31 to remove bearing bracket 330.
At the same time, pull shaft protecting sleeve 524.01 (if any) with complete
cartridge seal 433 off shaft 210.
5. Take care not to damage O-rings 412.01/.31, if any.
6. Undo hexagon nut 920.02 and remove seal cover 471.01 and/or the seal
cartridge.
Observe the seal installation drawing of the mechanical seal.
7.4.7 Dismantling the bearings

✓ The bearing bracket is kept in a clean and level assembly area.
1. Undo the socket head cap screw in the coupling hub.
2. Pull the coupling half off the pump shaft with a puller.
3. Remove key 940.02.
4. Remove fan hood 882, fan hub 485.02 and fan wheel 831.02, if any.
5. Undo hexagon nut 920.02 and remove seal cover 471.01 and/or the seal
cartridge.
6. Undo grub screws 904.41/.42 and remove throwers 507.01/.02.
7. Undo socket head cap screws 914.01 and remove pump-end bearing cover 360.01
as well as joint ring 400.01.
8. Undo hexagon head bolts 901.37 and remove motor-end bearing cover 360.02 as
well as O-ring 412.22, if required.
9. Carefully drive shaft 210 together with angular contact ball bearing 320.02 and
the inner ring of cylindrical roller bearing 322.01, including oil thrower 508.01, if
any, out of the bearing bracket towards the drive end.
10. Remove cylindrical roller bearing 322.01 (roller cage) from bearing bracket 330.
11. Heat up the inner ring of cylindrical roller bearing 322.01 to 80 °C, and pull it off
the shaft.
12. If oil thrower 508.01 is fitted, remove grub screw 904.20 and pull the oil thrower
off the shaft.
13. Bend open lockwasher 931.01 behind keywayed nut 920.21 on shaft 210.
14. Unscrew keywayed nut 920.21 (right-hand thread) and remove lockwasher
931.01.
15. Heat up angular contact ball bearing 320.02 and the inner ring of cylindrical
roller bearing 322.01 to 80 °C, and pull them off shaft 210.
7.5 Reassembling the pump set
7.5.1 General notes/Safety regulations

CAUTION
Improper reassembly
Damage to the pump!
▷ Reassemble the pump (set) in accordance with the general rules of sound
engineering practice.
▷ Use original spare parts only.
Sequence Always reassemble the pump in accordance with the corresponding general assembly
drawing.
RPH 47 of 68
Seal elements ▪ Gaskets

– Always use new gaskets, making sure that they have the same thickness as
the old ones.
– Always fit gaskets of asbestos-free materials or graphite without using
lubricants (e.g. copper grease, graphite paste).
▪ O-rings
– Never use O-rings that have been glued together from material sold by the
metre.
CAUTION
Contact of O-ring with graphite or similar material
Fluid could escape!
▷ Do not coat O-ring with graphite or similar material.
▷ Use animal fats or lubricants based on silicone or PTFE.
▪ Assembly adhesives
– For gaskets, avoid the use of assembly adhesives, if possible.
– Should assembly adhesives be required after all, use a commercially available
contact adhesive (e.g. "Pattex").
– Only apply adhesive at selected points and in thin layers.
– Never use quick-setting adhesives (cyanoacrylate adhesives).
– Coat the locating surfaces of the individual components and screwed
connections with graphite or similar before reassembly.
Tightening torques For reassembly, tighten all screws and bolts as specified in this manual. (⇨ Section 7.6
Page 51)
7.5.2 Fitting the bearings

✓ The individual parts are kept in a clean and level assembly area.
✓ All disassembled parts have been cleaned and checked for wear.
✓ Any damaged or worn parts have been replaced by original spare parts.
✓ The sealing surfaces have been cleaned.
1. Heat up angular contact ball bearing 320.02 and the inner ring of cylindrical
rolling element bearing 322.01 to approximately 80 ℃ in an oil bath.
2. Push angular contact ball bearing 320.02 onto shaft 210 as far as it will go.
3. Push the inner ring of cylindrical roller bearing 322.01 onto shaft 210 as far as
it will go.
4. For bearing brackets B03 and B05 make sure that disc 550 is positioned
correctly.
NOTE
Angular contact ball bearings must be installed in "O" arrangement. Angular contact ball
bearings installed in pairs must always be from the same manufacturer.
5. Use a spanner wrench to tighten keywayed nut 920.21 (right-hand thread)

without lockwasher 931.01.
6. Let angular contact ball bearing 320.01 cool down to approximately 5 °C
above ambient temperature.
7. Re-tighten keywayed nut 920.21, then unscrew it again.
8. Apply a few spots of a suitable lubricant (e.g. Molykote) to the contact faces
of lockwasher 931.01 and keywayed nut 920.21.
9. Fit lockwasher 931.01.
10. Tighten keywayed nut 920.21.
48 of 68 RPH
12. If provided, push oil thrower 508.01 on shaft 210.

13. Screw grub screw 904.20 into oil thrower 508.01.
14. Push cylindrical roller bearing 322.01 (roller cage) into bearing bracket 330.
15. Carefully push shaft 210 together with angular contact ball bearing 320.02
and the inner ring of cylindrical roller bearing 322.01, including oil thrower
508.01 (if any) into bearing bracket 330 towards the pump end.
16. Insert O-ring 412.22 into the groove of motor-end bearing cover 360.02.
17. Insert motor-end bearing cover 360.02 with O-ring 412.22 into bearing bracket
330 from the motor end.
18. Screw hexagon head bolts 901.37 with bearing cover 360.02 into bearing
bracket 330 from the motor end.
19. Fit pump-end bearing cover 360.01 with joint ring 400.01.
20. Screw socket head cap screws 914.01 into bearing bracket 330.
21. Push thrower 507.01 onto shaft 210 from the pump end until it sits about
2 mm from pump-end bearing cover 360.01.
22. Screw grub screw 904.41 into pump-end thrower 507.01.
23. Push thrower 507.02 onto shaft 210 from the pump end until it sits about
2 mm from pump-end bearing cover 360.02.
24. Screw grub screw 904.21 into motor-end thrower 507.02.
25. Fit fan hood 882, fan hub 485.02 and fan wheel 831.02, if any.
26. Insert key 940.02 into the keyway at the shaft end from the motor end.
27. Pull the coupling half onto the shaft end.
28. Screw socket head cap screw into the coupling hub.
7.5.3 Installing the shaft seal
7.5.3.1 Installing the cartridge seal

Always observe the following points when installing the cartridge seal:
▪ Install the cartridge seal as described in the seal installation drawing.
▪ Work cleanly and accurately.
▪ Prevent any damage to the sealing surfaces or O-rings.
1. Fit seal cover 471 and/or seal cartridge and tighten hexagon head bolts 920.02.
2. Push casing cover 161 with cartridge seal 433 onto the shaft from the pump end.
3. Carefully guide complete pre-assembled bearing bracket 330 over the studs
902.15 which have been screwed into casing cover 161.
4. On cooled versions, make sure not not damage O-rings 412.01/.31 at casing cover
161.
5. Screw casing cover 161 to complete bearing cover 330 with hexagon nuts 920.15.
7.5.4 Fitting the impeller
7.5.4.1 Fitting the impeller — for all bearing bracket sizes

✓ The pre-assembly (motor, shaft, bearing bracket, casing cover) is kept in a clean
and level assembly area.
RPH 49 of 68
✓ All disassembled parts have been cleaned and checked for wear.
1. If applicable, push throttling bush 542.02 onto impeller 230.
2. Screw grub screws 904.38 into throttling bush 542.02.
3. Push joint ring 411.32 onto shaft 210.
4. Place key 940.01 into the keyway of shaft 210.
5. Slip impeller 230 onto shaft 210.
7.5.4.2 Fastening the impeller — for bearing brackets B02 to B05

1. Insert lockwasher 931.02.
2. Insert new joint ring 411.31, if applicable.
3. Screw impeller nut 922.01 with threaded insert (right-hand thread) onto shaft
210.
Observe tightening torques. (⇨ Section 7.6.1 Page 51)
4. Bend back the lockwasher.
7.5.4.3 Fastening the impeller — for bearing brackets B06 and B07
1. Insert disc 550.87 and lockwasher 931.02.
2. Screw impeller screw 906 into shaft 210.
3. Observe the tightening torques. (⇨ Section 7.6.1 Page 51)
5. Insert new joint ring 411.31 into impeller 230.
6. Screw impeller hub cap 260 into impeller 230 (right-hand thread).
7.5.5 Installing the back pull-out unit
WARNING
Back pull-out unit tipping over
▷ Suspend or support the bearing bracket at the pump end.
50) and (⇨ Section 7.5.4.3 Page 50) have been observed/carried out.
✓ For back pull-out units without coupling, install the coupling in accordance with
the manufacturer's instructions.
1. If required, prevent the back pull-out unit from tipping over, e.g. by suspending
or supporting it. Then push it into volute casing 102 with new gasket 411.10.
2. Tighten nut 920.01 at volute casing 102. Observe the tightening torques. (⇨
Section 7.6.1 Page 51)
50 of 68 RPH
7.5.6 Mounting the motor

NOTE
Steps 1 and 2 do not apply to versions with spacer-type coupling.
1. Shift the motor to connect it to the pump via the coupling.

2. Fasten the motor to the baseplate.
3. Align the pump.
4. Connect the motor to the power supply (refer to manufacturer's product
literature).
7.6 Tightening torques
7.6.1 Tightening torques of the pump

Use a torque wrench to tighten the screwed connections (902.01/920.01) between the
volute casing and the casing cover.
Table 20: Tightening torques of screwed connections
Material A 193 Grade B7/ A 193 Grade B7/ 10.9 -- CF6M/Type 316
(Asia and B16 / B16
USA) A 540 Grade B24

Material 1.7709/1.6772 C35E+QT 8.8 A4-70 1.4571/1.4021
(Europe) (Monix 3K)
Stud16) Stud16) 902.15 Hexagon head Stud16) 902.02 Impeller nut 922.01 or
902.01 bolt 901.37 impeller screw 906
Tightening torque17) 18)

Tightening torque17)
Bearing bracket
[Nm]
[Nm]
[Nm]
[Nm]
[Nm]
Pump size
Quantity
Quantity
Quantity
Quantity
Quantity
Thread
Thread
Thread
Thread
B02S 25-180 12 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 Thread

M 14x1.5 8022)
28021)
25-230 16 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 14x1.5 8022)
28021)
40-180 12 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 14x1.5 8022)
28021)
40-230 16 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 14x1.5 8022)
28021)
B02L 40-181 12 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 16x1.5 13022)
28021)
40-231 16 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 16x1.5 13022)
28021)
16) Stud to DIN 938/DIN 939 with hexagon nuts to ISO 4032.
17) These values are determined on the basis of a friction coefficient μ = 0.12.
18) After repeated tightening of the threads and in case of good lubrication the values shall be reduced by 15 to 20 %.
19) Re-tighten impeller nut 922.01 or impeller screw 906 some 20 to 30 minutes after assembly. Bend back lockwasher 931.02.
20) Values for 1.7709 / A 193 Grade B7/B16 /
21) Values for 1.6772 (Monix 3K) / A 540 Grade B24
22) Values for 1.4571 / A 276 Type 316Ti
RPH 51 of 68
(Asia and B16 / B16

Material 1.7709/1.6772 C35E+QT 8.8 A4-70 1.4571/1.4021
(Europe) (Monix 3K)

Bearing bracket
[Nm]
[Nm]
[Nm]
[Nm]
[Nm]
Pump size
Quantity
Quantity
Quantity
Quantity
Quantity
Thread
Thread
Thread
Thread
Thread
40-280 16 M 20 33020) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 16x1.5 13022)
56521)
40-281 16 M 20 33020) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 16x1.5 13022)
56521)
40-361 20 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 16x1.5 13022)
56521)
50-180 12 M 16 16320) / 4 M 16 83 4 M 10 45 4 M 16 133 1 M 16x1.5 13022)
28021)
B03 50-230 12 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
50-280 16 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
50-360 20 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
50-450 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 20x1.5 250 22)
97021)
80-180 12 M 16 16320) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
28021)
80-230 12 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
80-280 16 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
80-360 20 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
100-180 12 M 16 16320) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
28021)
100-230 12 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
100-280 16 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
150-230 12 M 20 33020) / 4 M 20 168 4 M 12 77 4 M 16 133 1 M 20x1.5 25022)
56521)
B05S 80-450 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 24x1.5 35022)
97021)
52 of 68 RPH
(Asia and B16 / B16

Material 1.7709/1.6772 C35E+QT 8.8 A4-70 1.4571/1.4021
(Europe) (Monix 3K)

Bearing bracket
[Nm]
[Nm]
[Nm]
[Nm]
[Nm]
Pump size
Quantity
Quantity
Quantity
Quantity
Quantity
Thread
Thread
Thread
Thread
Thread
150-280 12 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 24x1.5 35022)
97021)
100-360 16 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 24x1.5 35022)
97021)
100-450 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 24x1.5 35022)
97021)
150-360 16 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 24x1.5 35022)
97021)
200-280 12 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 24x1.5 35022)
97021)
B05L 150-450 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
97021)
150-501 30 M 16 16320) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
28021)
200-360 16 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
97021)
200-450 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
97021)
200-401 24 M 16 16320) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
28021)
200-501 24 M 20 33020) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
56521)
250-401 24 M 16 16320) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
28021)
250-501 24 M 20 33020) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 60022)
56521)
300-400 24 M 20 33020) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 30022) /
56521) 40023)
300-500 24 M 20 33020) / 4 M 24 290 4 M 16 190 4 M 16 133 1 M 30x1.5 30022) /
56521) 40023)
B06 150-630 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
200-670 24 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
23) Values for 1.4021 / A 276 Type 420
RPH 53 of 68
(Asia and B16 / B16

Material 1.7709/1.6772 C35E+QT 8.8 A4-70 1.4571/1.4021
(Europe) (Monix 3K)

Bearing bracket
[Nm]
[Nm]
[Nm]
[Nm]
[Nm]
Pump size
Quantity
Quantity
Quantity
Quantity
Quantity
Thread
Thread
Thread
Thread
Thread
250-630 20 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
250-710 24 M 24 56520) / 4 M 24 290 4 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
300-630 20 M 24 56520) / 4 M 24 290 8 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
350-400 16 M 24 56520) / 4 M 24 290 8 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
350-500 20 M 24 56520) / 4 M 24 290 8 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
350-630 20 M 24 56520) / 4 M 24 290 8 M 16 190 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
B07 350-710 24 M 24 56520) / 4 M 24 290 10 M 12 77 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
400-504 20 M 24 56520) / 4 M 24 290 10 M 12 77 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
400-506 20 M 24 56520) / 4 M 24 290 10 M 12 77 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
400-710 24 M 24 56520) / 4 M 24 290 10 M 12 77 4 M 20 270 1 M 30x1.5 30022) /
97021) 40023)
7.7 Spare parts stock
7.7.1 Ordering spare parts

Always quote the following data when order replacement or spare parts:
▪ Type series
▪ Size
▪ KSB order number
▪ Material variant
▪ Year of construction
Refer to the name plate for all data.
Also supply the following data:
54 of 68 RPH
▪ Part description
▪ Part No.
▪ Quantity of spare parts
▪ Delivery address
▪ Mode of dispatch (freight, mail, express freight, air freight)
Refer to the general assembly drawing for part numbers and descriptions. (⇨ Section
9.1 Page 60)
Also see
• Name plate [⇨ 15]
7.7.2 Recommended spare parts stock for 2 years' operation to DIN 24296
Table 21: Quantity of spare parts for recommended spare parts stock
Part No. Description Number of pumps (including stand-by pumps)
2 3 4 5 6 and 7 8 and 9 10 and
more
210 Shaft 1 1 1 2 2 2 20 %
230 Impeller 1 1 1 2 2 2 20 %
320.02 Angular contact ball bearing 1 1 2 2 2 3 25 %
(set)
322.01 Cylindrical roller bearing 1 1 2 2 2 3 25 %
330 Bearing bracket -- -- -- -- -- 1 2
502.01/.0224) Casing wear ring 2 2 2 3 3 4 50 %
503.01/.0224) Impeller wear ring 2 2 2 3 3 4 50 %
542.02 Throttling bush 1 1 2 2 2 3 30 %
- Sealing elements 4 6 8 8 9 10 100 %
433 Mechanical seal complete 1 1 2 2 2 3 25 %
7.7.3 Interchangeability of pump components

Components featuring the same number in a column are interchangeable.
Table 22: Interchangeability of pump components
Part description
Casing wear ring, discharge side
Impeller wear ring, suction side

Casing wear ring, suction side
Angular contact ball bearing
Bearing cover, motor end

Bearing cover, pump end
Cylindrical roller bearing
Impeller, discharge side

Casing cover, uncooled
Casing cover, cooled
Thrower, motor end

Thrower, pump end
Impeller hub cap
Bearing bracket
Mechanical seal
Throttling bush
Impeller screw
Volute casing
Impeller nut
Oil thrower
Seal cover
Joint ring
Impeller
Bearing bracket
Shaft
Pump size
Part No.
320.02
322.01
360.01
360.02
411.10
471.01
502.01
502.02
503.01
503.02
507.01
507.02
508.01
542.01
922.01
102
161
210
230
260
330
433
906
B02S 25-180 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1
25-230 2 2 2 1 2 - 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 - 1
40-180 3 1 1 1 3 - 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 - 1
40-230 4 2 2 1 4 - 1 1 1 1 1 2 1 1 2 2 2 2 1 1 1 1 - 1
24) If any
RPH 55 of 68
Part description
Casing wear ring, discharge side
Impeller wear ring, suction side

Casing wear ring, suction side
Angular contact ball bearing
Bearing cover, motor end

Bearing cover, pump end
Cylindrical roller bearing
Impeller, discharge side

Casing cover, cooled
Thrower, motor end

Thrower, pump end
Impeller hub cap
Bearing bracket
Mechanical seal
Throttling bush
Impeller screw
Volute casing
Impeller nut
Oil thrower
Seal cover
Joint ring
Impeller
Bearing bracket
Shaft
Pump size
Part No.
320.02
322.01
360.01
360.02
411.10
471.01
502.01
502.02
503.01
503.02
507.01
507.02
508.01
542.01
922.01
102
161
210
230
260
330
433
906
B02L 40-181 6 3 3 2 6 - 1 1 1 1 1 1 1 1 4 4 4 4 1 1 1 2 - 2
40-280 5 5 5 2 5 - 1 1 1 1 1 3 1 1 3 5 3 5 1 1 1 2 - 2
40-231 7 4 4 2 7 - 2 2 2 2 2 2 1 1 4 4 4 4 1 1 1 2 - 2
40-281 8 5 5 2 8 - 2 2 2 2 2 3 1 1 4 5 5 5 1 1 1 2 - 2
40-361 9 6 6 2 9 - 2 2 2 2 2 4 1 1 4 7 4 7 1 1 1 2 - 2
50-180 10 7 7 2 10 - 2 2 2 2 2 1 1 1 5 5 5 5 1 1 1 2 - 2
B03 50-230 11 8 8 3 11 - 2 2 2 2 2 2 2 2 5 5 5 5 2 2 2 3 - 3
50-280 12 9 9 3 12 - 2 2 2 2 2 3 2 2 5 5 5 5 2 2 2 3 - 3
50-360 13 10 10 3 13 - 2 2 2 2 2 4 2 2 5 7 5 7 2 2 2 3 - 3
50-450 14 11 11 3 14 - 2 2 2 2 2 5 2 2 5 9 5 9 2 2 2 3 - 3
80-180 15 12 12 3 15 - 2 2 2 2 2 2 2 2 6 6 6 6 2 2 2 3 - 3
80-230 16 12 12 3 16 - 2 2 2 2 2 2 2 2 6 6 6 6 2 2 2 3 - 3
80-280 17 9 9 3 17 - 2 2 2 2 2 3 2 2 6 6 6 6 2 2 2 3 - 3
80-360 18 13 13 3 18 - 2 2 2 2 2 4 2 2 6 7 6 7 2 2 2 3 - 3
100-180 19 15 15 3 19 - 2 2 2 2 2 5 2 2 7 7 7 7 2 2 2 3 - 3
100-230 20 16 16 3 20 - 2 2 2 2 2 5 2 2 7 7 7 7 2 2 2 3 - 3
100-280 21 17 17 3 21 - 2 2 2 2 2 3 2 2 7 7 7 7 2 2 2 3 - 3
150-230 22 20 20 3 22 - 2 2 2 2 2 2 2 2 9 9 9 9 2 2 2 3 - 3
B05S 80-450 23 14 14 4 23 - 3 3 3 3 3 5 3 3 6 6 6 6 3 3 3 4 - 4
100-360 24 18 18 4 24 - 3 3 3 3 3 4 3 3 7 7 7 7 3 3 3 4 - 4
100-450 25 19 19 4 25 - 3 3 3 3 3 5 3 3 8 8 8 8 3 3 3 4 - 4
150-280 26 21 21 4 26 - 3 3 3 3 3 3 3 3 9 9 9 9 3 3 3 4 - 4
150-360 27 22 22 4 27 - 3 3 3 3 3 4 3 3 9 9 9 9 3 3 3 4 - 4
200-280 28 24 24 4 28 - 3 3 3 3 3 5 3 3 11 11 11 11 3 3 3 4 - 4
B05L 150-450 29 23 23 5 29 - 3 3 3 4 3 5 3 3 10 12 10 12 3 3 3 5 - 5
150-501 32 27 27 5 32 - 3 3 3 3 3 6 3 3 11 11 11 11 3 3 3 5 - 5
200-360 30 25 25 5 30 - 3 3 3 4 3 4 3 3 12 13 12 13 3 3 3 5 - 5
200-401 33 28 28 5 33 - 3 3 3 3 3 7 3 3 14 14 14 14 3 3 3 5 - 5
200-450 31 26 26 5 31 - 3 3 3 4 3 5 3 3 12 13 12 13 3 3 3 5 - 5
200-501 34 29 29 5 34 - 3 3 3 3 3 6 3 3 15 15 15 15 3 3 3 5 - 5
250-401 35 30 30 5 35 - 3 3 3 3 3 7 3 3 16 16 16 16 3 3 3 5 - 5
250-501 36 31 31 5 36 - 3 3 3 3 3 6 3 3 17 17 17 17 3 3 3 5 - 5
300-400 41 36 36 5 41 - 3 3 3 3 3 7 3 3 21 22 21 22 3 3 3 5 - 5
300-500 42 37 37 5 42 - 3 3 3 3 3 8 3 3 25 26 25 26 3 3 3 5 - 5
B06 150-630 37 32 32 6 37 1 4 4 4 4 4 8 4 4 18 19 18 19 4 4 4 6 1 -
200-670 38 33 33 6 38 1 4 4 4 4 4 9 4 4 20 20 20 20 4 4 4 6 1 -
250-630 39 34 34 6 39 1 4 4 4 4 4 8 4 4 21 22 21 22 4 4 4 6 1 -
250-710 40 35 35 6 40 1 4 4 4 4 4 9 4 4 23 24 23 24 4 4 4 6 1 -
300-630 43 36 36 6 43 1 4 4 4 4 4 9 4 4 27 28 27 28 4 4 4 6 1 -
350-400 44 37 37 7 44 1 4 4 4 4 4 7 4 4 29 30 27 31 4 4 4 6 1 -
56 of 68 RPH
B07
Bearing bracket
400-710
400-506
400-504
350-710
350-630
350-500
Pump size
50
49
48
47
46
45
102 Volute casing
Part No.
37
38
38
37
36
38
37
38
38
37
36
38
161 Casing cover, cooled
Part description
8
8
8
8
6
6
210 Shaft
RPH
50
49
48
47
46
45
230 Impeller
1
1
1
1
1
1
260 Impeller hub cap
5
5
5
5
4
4
320.02 Angular contact ball bearing
5
5
5
5
4
4
322.01 Cylindrical roller bearing
5
5
5
5
4
4
330 Bearing bracket
5
5
5
5
4
4
360.01 Bearing cover, pump end
5
5
5
5
4
4
360.02 Bearing cover, motor end

8
9
10
11
11
10
5 411.10 Joint ring

5
5
5
4
4
433 Mechanical seal

5
5
5
5
4
4
471.01 Seal cover

38
36
34
34
32
29
502.01 Casing wear ring, suction side

39
36
34
34
32
29
502.02 Casing wear ring, discharge side

37
37
35
35
33
27
503.01 Impeller wear ring, suction side

40
37
35
35
33
27
503.02 Impeller, discharge side

5
5
5
5
4
4
507.01 Thrower, pump end

5
5
5
5
4
4
507.02 Thrower, motor end

5
5
5
5
4
4
508.01 Oil thrower

7
7
7
7
6
6
542.01 Throttling bush

1
1
1
1
1
1
906 Impeller screw

-
-
-
-
-
-
922.01 Impeller nut
57 of 68
8 Trouble-shooting
8 Trouble-shooting
A Pump delivers insufficient flow rate
B Motor overload
C Excessive pump discharge pressure
D Excessive bearing temperature
E Leakage at the pump
F Excessive leakage at the shaft seal
G Vibrations during pump operation
H Excessive rise of temperature inside the pump

Table 23: Trouble-shooting
A B C D E F G H Possible cause Remedy 25)
X Pump delivers against an excessively Re-adjust to duty point.
high discharge pressure. Check system for impurities.
Fit a larger impeller. 26)
Increase the speed (turbine, I.C. engine).
X X X Pump or piping are not completely Vent and/or prime.
vented or primed.
X Supply line or impeller clogged. Remove deposits in the pump and/or piping.
X Formation of air pockets in the piping. Alter piping layout.
Fit a vent valve.
X X X Suction head is too high/NPSH available Check/alter liquid level.
(positive suction head) is too low. Install pump at a lower level.
Fully open the shut-off valve in the suction
line.
Change suction line if the friction losses in the
suction line are too high.
Check any strainers installed/suction opening.
Observe permissible speed of pressure fall.
X Air intake at the shaft seal. Clean barrier fluid duct, supply external
barrier fluid, if necessary, or increase barrier
fluid pressure.
Fit new shaft seal.
X Wrong direction of rotation. Interchange two of the phases of the power
supply cable.
X Speed is too low. 26)
- Increase voltage/frequency at the frequency
- Operation with frequency inverter inverter in the permissible range.
- Operation without frequency inverter - Check the voltage.
X X Impeller Replace worn components by new ones.
X X Pump back pressure is lower than Re-adjust to duty point.
specified in the purchase order. In the case of persistent overloading, turn
down impeller. 26)
X Density or viscosity of the fluid Contact KSB.
pumped is higher than stated in the
purchase order.
X X Speed is too high. Reduce speed. 26)
X Defective seal. Fit new seal between volute casing and
discharge cover.
X Worn shaft seal. Fit new shaft seal.
Check flushing liquid / barrier fluid.
25) Pump pressure must be released before attempting to remedy faults on parts which are subjected to pressure.
26) Request particulars.
58 of 68 RPH
8 Trouble-shooting
A B C D E F G H Possible cause Remedy 25)

X Vibrations during pump operation. Correct suction conditions.
Re-align the pump.
Re-balance the impeller.
Increase pressure at the pump suction nozzle.
X X X The pump set is misaligned. Re-align.
X X X Pump is warped or sympathetic Check pipeline connections and secure fixing
vibrations in the piping. of pump; if required, reduce the distances
between the pipe clamps.
Fix the pipelines using anti-vibration material.
X X Insufficient or excessive quantity of Top up, reduce or change lubricant.
lubricant or unsuitable lubricant.
X Non-compliance with specified Correct distance according to the general
coupling distance. arrangement drawing.
X X Motor is running on two phases only. Replace the defective fuse.
Check the electric cable connections.
X Rotor is out of balance. Clean the impeller.
Re-balance the impeller.
X Defective bearing(s) Fit new bearing(s).
X X Flow rate is too low. Increase the minimum flow rate.
X Incorrect inflow of circulation liquid Increase the free passage.
25) Pump pressure must be released before attempting to remedy faults on parts which are subjected to pressure.
RPH 59 of 68
9 Related Documents
9 Related Documents
9.1 General assembly drawing with list of components
9.1.1 Bearing brackets B02 to B05

411.67
931.02 916.16
922.01 502.01 411.31 904.07 904.38 920.01 904.41 914.01 360.01 642 931.01 412.22 904.42 831.02 904.37 210
503.01 102 904.04 940.01 902.01 411.32 330 400.01 913.03 69-10 920.21 901.37 485.02 940.02
720-12
638
a)
b) D01040/3
411.41 744.07
724.01 723.21
916.19
901.20 904.06 723.23 411.01 503.02 542.02 916.18 901.30 901.31 507.01 916.46 525.09 832 360.02 901.80
920.20 710.21 904.03 902.42 230 502.02 411.10 412.01 902.15 920.02 322.01 320.02 901.84 904.43 507.02
550.20 920.42 920.15 902.02 550 550.74
550.42 412.31
Fig. 12: Bearing brackets B02 to B05, a) uncooled and b) cooled

Table 24: Bearing brackets B02 to B05
Part No. Part description Scope of supply
102 Volute casing with joint ring 411.10, casing wear ring 502.01, stud 902.01, grub
screw 904.03, plug 916.0127) , hexagon nut 920.01
161 Casing cover with joint ring 411.10, O-ring 412.01/.31 28) , casing wear ring
502.02 31) , hexagon head bolt 901.30, stud 902.15, grub screw
904.04 31) , plug 916.16, hexagon nut 920.15
210 Shaft with keywayed nut 920.21, lockwasher 931.01, key 940.01/.02
230 Impeller with impeller wear ring 503.01/.02, grub screw 904.06/0.07, joint
ring29) 411.31/.32/.67, lockwasher 931.02
320.02/550 30) Angular contact ball bearing with disc 550 (adjusting washer)
330 Bearing bracket (complete) with protective cage 69.10, bearing cover 360.01/.02, gasket
400.01, O-ring 412.22, constant-level oiler 638, oil level sight glass
642, pipe 710.21, hexagon head bolt 901.31/.37, vent plug 913.03,
plug 916.46, socket head cap screw 914.01
27) Not shown in drawing.

28) For cooled design only.
29) Optional
30) Only for bearing brackets B 03 and B 05.
60 of 68 RPH
9 Related Documents

360.01/.02 31) Bearing cover with gasket 400.01, O-ring 412.22, socket head cap screw 914.01
502.01/.02 31) Casing wear ring grub screw 904.03/.04 31)
503.01/.02 Impeller wear ring grub screw 904.06/0.07 31)
507.01/.02 Thrower grub screw 904.41/0.42
542.02 Throttling bush grub screw 904.38
638 Constant-level oiler
70-329) Drain line with joint ring 411.01, stud 902.42, hexagon nut 920.42, disc
550.42, flange 723.23, gate valve 744.07, pipe 710.21, flange
723.21, joint ring 411.41, blind flange 724.01, hexagon head bolt
901.20, hexagon nut 920.20, disc 550.20
831.02 Fan impeller29) with fan hood 832, fan hub 485.02, grub screw 904.37
922.01 Impeller nut
99-927) Set of sealing elements,
complete
9.1.2 Bearing brackets B06 and B07

260
550.87
906 916.16 931.01
931.02 502.01 411.31 904.07 904.38 920.01 161 904.41 914.01 360.01 642 169-10 412.22 904.42 831.02 904.37 210
503.01 102 904.04 940.01 902.01 411.32 330 400.01 913.03 638 920.21 901.37 485.02 940.02
a)
b) D01042/3
724.01 723.21
411.41 744.07
901.20 904.06 723.23 411.01 503.02 542.02 901.30 901.31 902.02 507.01 916.46 525.09 832 360.02 901.80
920.20 710.21 904.03 902.42 230 502.02 916.19 902.15 412.31 920.02 322.01 320.02 901.84 904.43 507.02
550.20 920.42 916.18 920.15 550.74
550.42 411.10 412.01
Fig. 13: Bearing brackets B06 and B07, a) uncooled and b) cooled
31) For impellers with balancing of axial thrust only.
RPH 61 of 68
9 Related Documents
Table 25: Bearing brackets B06 and B07

102 Volute casing with joint ring 411.10, casing wear ring 502.01, stud 902.01, grub
screw 904.03, plug 916.0132) , hexagon nut 920.01
161 Casing cover with joint ring 411.10, O-ring 412.01/.31 33) , casing wear ring
502.02 34) , hexagon head bolt 901.30, stud 902.15, grub screw
904.04 34) , plug 916.16, hexagon nut 920.15
210 Shaft with keywayed nut 920.21, lockwasher 931.01, key 940.01/.02
230 Impeller with impeller wear ring 503.01/.02, grub screw 904.06/0.07, joint
ring35) 411.31/.32/.67
260 Impeller hub cap
320.02 Angular contact ball bearing
330 Bearing bracket (complete) with protective cage 69.10, bearing cover 360.01/.02, gasket
400.01, O-ring 412.22, constant-level oiler 638, oil level sight glass
642, pipe 710.21, hexagon head bolt 901.31/.37, vent plug 913.03,
plug 916.46, socket head cap screw 914.01
360.01/.02 31) Bearing cover with gasket 400.01, O-ring 412.22, socket head cap screw 914.01
502.01/.02 31) Casing wear ring grub screw 904.03/.04 34)
503.01/.02 Impeller wear ring grub screw 904.06/0.07 34)
507.01/.02 Thrower grub screw 904.41/0.42
542.02 Throttling bush grub screw 904.38
550.87 Disc
638 Constant-level oiler
70-335) Drain line with joint ring 411.01, stud 902.42, hexagon nut 920.42, disc
550.42, flange 723.23, gate valve 744.07, pipe 710.21, flange
723.21, joint ring 411.41, blind flange 724.01, hexagon head bolt
901.20, hexagon nut 920.20, disc 550.20
831.02 Fan impeller35) with fan hood 832, fan hub 485.02, grub screw 904.37
906 Impeller screw
931.02 Lockwasher
99-932) Set of sealing elements,
complete
9.1.3 Design variants

Bearing bracket, cooled
D01044
Fig. 14: Bearing bracket, cooled
32) Not shown in drawing.

33) For cooled design only.
34) For impellers with balancing of axial thrust only.
35) Optional
62 of 68 RPH
9 Related Documents
Special pump design with

thrower
904.20 508.01 D01047
Fig. 15: Special pump design with thrower

Pump design with plug
916.01
D01044
Fig. 16: Pump design with plug

Tandem bearing assembly
D01043
320.02
Fig. 17: Tandem bearing assembly

Heatable casing
D01126
Fig. 18: Heatable casing
RPH 63 of 68
9 Related Documents
Auxiliary impeller
(inducer)
Fig. 19: Auxiliary impeller (inducer)
64 of 68 RPH
10 EC Declaration of Conformity
10 EC Declaration of Conformity
Manufacturer: KSB Aktiengesellschaft

Johann-Klein-Straße 9
67227 Frankenthal (Germany)
The manufacturer herewith declares that the pump/pump set:
RPH
KSB order number: ...................................................................................................
▪ is in conformity with the provisions of the following directives as applicable in their current version:
– EC Machinery Directive 2006/42/EC
The manufacturer also declares that

▪ the following harmonised international standards were applied:
– ISO 12100-1/A1, ISO 12100-2/A1,
– ISO 14121-1,
– EN 809/A1
▪ Applied national technical standards and specifications, in particular:

– DIN EN ISO 13709
Pegnitz, 29.12.2009
...........................................................
Name
Function
Responsible for compiling the technical documentation
KSB Aktiengesellschaft
Bahnhofplatz 1
91257 Pegnitz (Germany)
RPH 65 of 68
11 Certificate of Decontamination
11 Certificate of Decontamination
Type ................................................................................................................................
Order number/
Order item number36) ................................................................................................................................
Delivery date ................................................................................................................................
Field of application: ................................................................................................................................
Fluid handled36) : ................................................................................................................................
Please tick where applicable36) :
⃞ ⃞ ⃞ ⃞
radioactive explosive corrosive toxic
⃞ ⃞ ⃞ ⃞
harmful bio-hazardous highly flammable safe
Reason for return36) : ................................................................................................................................
Comments: ................................................................................................................................
................................................................................................................................
The pump/accessories have been carefully drained, cleaned and decontaminated inside and outside prior to dispatch/placing
at your disposal.
On sealless pumps, the rotor has been removed from the pump for cleaning.
⃞ No special safety precautions are required for further handling.

⃞ The following safety precautions are required for flushing fluids, fluid residues and disposal:
...............................................................................................................................................................
...............................................................................................................................................................
We confirm that the above data and information are correct and complete and that dispatch is effected in accordance with
the relevant legal provisions.
.................................................................... ....................................................... .......................................................

Place, date and signature Address Company stamp
36) Required fields
66 of 68 RPH
Index
Index
A M
Abrasive fluids 38 Maintenance/ repair 39
Mechanical seal 35
Misuse 9
B Monitoring equipment 12
Back pull-out unit 46
Bearing temperature 40
Bearings 16 N
Name plate 15
Noise characteristics 18
C
Certificate of decontamination 66
Clearance gaps 41 O
Commissioning/start-up 29 Oil lubrication
Constant-level oiler 29 Intervals 43
Coupling 41 Oil quality 43
Operating limits 8, 36
Order number 6
D Other applicable documents 6
Design 15, 18
Designation 15
Direction of rotation 27 P
Dismantling 45 Partly completed machinery 6
Disposal 14 Piping 22
Preservation 14, 38
Product description 15
E Pump casing 16
Explosion protection 11, 20, 24, 25, 26, 27, 31, 33, 34,
36, 39, 41, 43
R
Return to supplier 14
F Returning to service 38
Filling and venting 32 Running noises 39, 40
Filter 22, 42
Final check 32
Flow rate 37 S
Frequency of starts 36, 37 Safety 8
Function 18 Safety awareness 9
Scope of supply 18
Shaft seal 16
H Shutdown 35, 38
Heating 33 Spare parts 54
Heating speed 34 Start-up 34
Heating up 34 Storage 14, 38
I T
Impeller type 16 Temperature difference 34
Installation Temperature limits 11
Installation on foundation 20 Tightening torques 51
Installation at site 20 Transport 13
Intended use 8 Trouble-shooting 58
Interchangeability of pump components 55
W
K Water cooling 32
Keeping the pump warm 34
RPH 67 of 68
1316.8014/5-10
KSB Aktiengesellschaft
P.O. Box 1361 • 91253 Pegnitz • Bahnhofplatz 1, 91257 Pegnitz (Germany)
Tel. +49 9241 71-0 • Fax +49 9241 71-1793
www.ksb.com

RPH (11th Edition) - Installation and Operating Manual

Uploaded by

Copyright:

Available Formats

RPH (11th Edition) - Installation and Operating Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RPH (11th Edition) - Installation and Operating Manual

Uploaded by

Copyright:

Available Formats

Process Pump

KSB Aktiengesellschaft Pegnitz

Subject to technical modification without prior notice.

© KSB Aktiengesellschaft Frankenthal 30.12.2009

3 Transport/Temporary Storage/Disposal ........................................... 13

4 Description of the Pump (Set) .......................................................... 15

5 Installation at Site ............................................................................. 20

5.5 Protective equipment ................................................................................... 24

9 Related Documents ........................................................................... 60

10 EC Declaration of Conformity .......................................................... 65

11 Certificate of Decontamination ....................................................... 66

Back pull-out design Pool of pumps

Noise characteristics (⇨ Section 4.6 Page 18)

1.2 Installation of partly completed machinery

1.3 Target group

1.4 Other applicable documents

1) If agreed to be included in the scope of supply

2.1 Key to safety symbols/markings

2.3 Intended use

Prevention of foreseeable misuse

2.4 Personnel qualification and training

The responsibilities, competence and supervision of all personnel involved in

Deficits in knowledge must be rectified by sufficiently trained specialist personnel

Training on the pump (set) must always be supervised by technical specialist

2.5 Consequences and risks caused by non-compliance with these operating

2.6 Safety awareness

▪ Safety regulations for handling hazardous substances

2.7 Safety information for the operator/user

2.8 Safety information for maintenance, inspection and installation work

2.9 Unauthorised modes of operation

2.10 Explosion protection

Special conditions apply to the operation of explosion-proof pump sets to EC

Motor The motor must be considered separately.

2.10.2 Temperature limits

Misuse, malfunctions or non-compliance with the instructions may result in

2) Depending on the material variant

If the pump is to be operated at a higher temperature, the data sheet is missing or if

2.10.3 Monitoring equipment

2.10.4 Operating limits

Fig. 1: Transporting a pump

Fig. 2: Transporting a complete pump set

Fig. 3: Transporting a pump on baseplate

3.2 Storage and preservation

3.3 Return to supplier

1. Dismantle the pump (set).

4 Description of the Pump (Set)

4.1 General description

4.3 Name plate

1 Year of construction 2 Type series/pump size

4.4 Design details

▪ Back pull-out design

3) American Petroleum Institute

Table 6: Bearing bracket designation

Refer to the data sheet to find your bearing design.

Table 8: Standard bearing assembly

Table 9: Reinforced bearing assembly (triple bearing assembly)

4.5 Design and function

1 Clearance gap 2 Discharge nozzle

Sealing The pump is sealed by a standardised mechanical seal.

4.6 Noise characteristics