Arm Primecell Synchronous Serial Port (Pl022) : Technical Reference Manual

ARM PrimeCell Synchronous Serial
Port (PL022)
Revision: r1p3
Technical Reference Manual
Copyright © 2000-2001, 2009, 2011. All rights reserved.

ARM DDI 0194G (ID110411)
ARM PrimeCell Synchronous Serial Port (PL022)
Copyright © 2000-2001, 2009, 2011. All rights reserved.

Release Information
Change history
Date Issue Confidentiality Change
6 September 2000 A Non-Confidential First release
19 March 2001 B Non-Confidential Second release
15 June 2001 C Non-Confidential Third release
31 July 2001 D Non-Confidential Fourth release
30 January 2009 E Non-Confidential Unrestricted Access Fifth release
01 November 2011 F Non-Confidential Unrestricted Access Sixth release
04 November 2011 G Non-Confidential Unrestricted Access Seventh release
Proprietary Notice
Words and logos marked with ® or ™ are registered trademarks or trademarks owned by ARM Limited, except as
otherwise stated below in this proprietary notice. Other brands and names mentioned herein may be the trademarks of
their respective owners.
Neither the whole nor any part of the information contained in, or the product described in, this document may be
adapted or reproduced in any material form except with the prior written permission of the copyright holder.
The product described in this document is subject to continuous developments and improvements. All particulars of the
product and its use contained in this document are given by ARM in good faith. However, all warranties implied or
expressed, including but not limited to implied warranties of merchantability, or fitness for purpose, are excluded.
This document is intended only to assist the reader in the use of the product. ARM Limited shall not be liable for any
loss or damage arising from the use of any information in this document, or any error or omission in such information,
or any incorrect use of the product.
Confidentiality Status
This document is Non-Confidential. The right to use, copy and disclose this document may be subject to license
restrictions in accordance with the terms of the agreement entered into by ARM and the party that ARM delivered this
document to.
Product Status
The information in this document is final, that is for a developed product.
Web Address
http://www.arm.com
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. ii
ID110411 Non-Confidential
Contents
ARM PrimeCell Synchronous Serial Port (PL022)
Preface
About this book ........................................................................................................... vi
Feedback ..................................................................................................................... x
Chapter 1 Introduction
1.1 About the ARM PrimeCell SSP (PL022) .................................................................. 1-2
1.2 Product revisions ..................................................................................................... 1-5
Chapter 2 Functional Overview

2.1 PrimeCell SSP overview .......................................................................................... 2-2
2.2 PrimeCell SSP functional description ...................................................................... 2-3
2.3 PrimeCell SSP operation ......................................................................................... 2-6
Chapter 3 Programmer’s Model

3.1 About the programmer’s model ............................................................................... 3-2
3.2 Summary of PrimeCell SSP registers ...................................................................... 3-3
3.3 Register descriptions ............................................................................................... 3-4
3.4 Interrupts ................................................................................................................ 3-20
Chapter 4 Programmer’s Model for Test

4.1 PrimeCell SSP test harness overview ..................................................................... 4-2
4.2 Scan testing ............................................................................................................. 4-3
4.3 Test registers ........................................................................................................... 4-4
4.4 Integration testing of block inputs ............................................................................ 4-8
4.5 Integration testing of block outputs ........................................................................ 4-10
4.6 Integration test summary ....................................................................................... 4-13
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. iii
Contents
Appendix A Signal Descriptions

A.1 AMBA APB signals .................................................................................................. A-2
A.2 On-chip signals ........................................................................................................ A-3
A.3 Signals to pads ........................................................................................................ A-4
Appendix B Revisions
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. iv
Preface
This preface introduces the ARM PrimeCell Synchronous Serial Port (PL022) Technical
Reference Manual. It contains the following sections:
• About this book on page vi
• Feedback on page x.
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. v
Preface
About this book

This book is for the ARM PrimeCell Synchronous Serial Port (PL022).
Product revision status
The rnpn identifier indicates the revision status of the product described in this book, where:
rn Identifies the major revision of the product.
pn Identifies the minor revision or modification status of the product.
Intended audience
This book is written for hardware and software engineers with experience and knowledge of
implementing System-on-Chip (SoC) designs and, to enable designers to integrate the peripheral
into a target system.
Using this book
This book is organized into the following chapters:
Chapter 1 Introduction
Read this for an introduction to the PrimeCell Synchronous Serial Port (SSP) and
its features.
Chapter 2 Functional Overview

Read this for a description of the major functional blocks of the PrimeCell SSP.
Chapter 3 Programmer’s Model

Read this for a description of the PrimeCell SSP registers and programming
details.
Chapter 4 Programmer’s Model for Test

Read this for a description of the logic in the PrimeCell SSP for integration
testing.
Appendix A Signal Descriptions

Read this for a description of the PrimeCell SSP signals.
Appendix B Revisions
Read this for a description of the technical changes between released issues of this
book.
Glossary
The ARM Glossary is a list of terms used in ARM documentation, together with definitions for
those terms. The ARM Glossary does not contain terms that are industry standard unless the
ARM meaning differs from the generally accepted meaning.
See ARM Glossary, http://infocenter.arm.com/help/topic/com.arm.doc.aeg0014-/index.html.
Conventions
Conventions that this book can use are described in:

• Typographical on page vii
• Timing diagrams on page vii
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. vi
Preface
• Signals.
Typographical
The typographical conventions are:
italic Highlights important notes, introduces special terminology, denotes

internal cross-references, and citations.
bold Highlights interface elements, such as menu names. Denotes signal

names. Also used for terms in descriptive lists, where appropriate.
monospace Denotes text that you can enter at the keyboard, such as commands, file
and program names, and source code.
monospace Denotes a permitted abbreviation for a command or option. You can enter
the underlined text instead of the full command or option name.
monospace italic Denotes arguments to monospace text where the argument is to be

replaced by a specific value.
monospace bold Denotes language keywords when used outside example code.
< and > Enclose replaceable terms for assembler syntax where they appear in code
or code fragments. For example:
MRC p15, 0 <Rd>, <CRn>, <CRm>, <Opcode_2>
Timing diagrams
The figure named Key to timing diagram conventions explains the components used in timing
diagrams. Variations, when they occur, have clear labels. You must not assume any timing
information that is not explicit in the diagrams.
Shaded bus and signal areas are undefined, so the bus or signal can assume any value within the
shaded area at that time. The actual level is unimportant and does not affect normal operation.
Clock
HIGH to LOW
Transient
HIGH/LOW to HIGH
Bus stable
Bus to high impedance
Bus change
High impedance to stable bus
Key to timing diagram conventions
Signals
The signal conventions are:
Signal level The level of an asserted signal depends on whether the signal is
active-HIGH or active-LOW. Asserted means:
• HIGH for active-HIGH signals
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. vii
Preface
• LOW for active-LOW signals.
Lower-case n At the start or end of a signal name denotes an active-LOW signal.
Prefix A Denotes global Advanced eXtensible Interface (AXI) signals.
Prefix AR Denotes AXI read address channel signals.
Prefix AW Denotes AXI write address channel signals.
Prefix B Denotes AXI write response channel signals.
Prefix C Denotes AXI low-power interface signals.
Prefix H Denotes Advanced High-performance Bus (AHB) signals.
Prefix P Denotes Advanced Peripheral Bus (APB) signals.
Prefix R Denotes AXI read data channel signals.
Prefix W Denotes AXI write data channel signals.
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. viii
Preface
Additional reading
This section lists publications by ARM and by third parties.
See Infocenter, http://infocenter.arm.com, for access to ARM documentation.
ARM publications
This book contains information that is specific to this product. See the following documents for
other relevant information:
• AMBA® Specification (Rev 2.0) (ARM IHI 00011)
• ARM PrimeCell Synchronous Serial Port (PL022) Integration Manual

(PL022 INTM 0000)
• ARM PrimeCell Synchronous Serial Port (PL022) Design Manual (PL022 DDES 0000)
• ARM PrimeCell Synchronous Serial Port (PL020) Technical Reference Manual

(ARM DDI 0141)
• ARM PrimeCell Synchronous Serial Port Master and Slave (PL021) Technical Reference
Manual (ARM DDI 0171).
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. ix
Preface
Feedback
ARM welcomes feedback on this product and its documentation.
Feedback on this product
If you have any comments or suggestions about this product, contact your supplier and give:
• The product name.
• The product revision or version.
• An explanation with as much information as you can provide. Include symptoms if

appropriate.
Feedback on this book
If you have any comments on content then send an e-mail to [email protected]. Give:
• the title
• the number, ARM DDI 0194G
• the page numbers to which your comments apply
• a concise explanation of your comments.
ARM also welcomes general suggestions for additions and improvements.
Note
ARM tests the PDF only in Adobe Acrobat and Acrobat Reader, and cannot guarantee the
quality of the represented document when used with any other PDF reader.
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. x
Chapter 1
Introduction
This chapter introduces the ARM PrimeCell Synchronous Serial Port (PL022).
It contains the following sections:

• About the ARM PrimeCell SSP (PL022) on page 1-2
• Product revisions on page 1-5.
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. 1-1
Introduction
1.1 About the ARM PrimeCell SSP (PL022)

The PrimeCell Synchronous Serial Port (SSP) is an Advanced Microcontroller Bus Architecture
(AMBA) slave block that connects to the Advanced Peripheral Bus (APB). The PrimeCell SSP
is an AMBA compliant System-on-Chip (SoC) peripheral that is developed, tested, and licensed
by ARM.
The PrimeCell SSP is a master or slave interface that enables synchronous serial communication
with slave or master peripherals having one of the following:
• a Motorola SPI-compatible interface
• a Texas Instruments synchronous serial interface
• a National Semiconductor Microwire interface.
In both master and slave configurations, the PrimeCell SSP performs:
• parallel-to-serial conversion on data written to an internal 16-bit wide, 8-location deep

transmit FIFO
• serial-to-parallel conversion on received data, buffering it in a similar 16-bit wide,

8-location deep receive FIFO.
Interrupts are generated to:

• request servicing of the transmit and receive FIFO
• inform the system that a receive FIFO over-run has occurred
• inform the system that data is present in the receive FIFO after an idle period has expired.
The following sections describe the features of the PrimeCell SSP:

• Features of the PrimeCell SSP
• SPI features on page 1-4
• Microwire features on page 1-4
• Texas Instruments synchronous serial interface features on page 1-4.
Note
Because of changes in the programmer’s model, the PrimeCell SSP (PL022) is not
backwards-compatible with the previous PrimeCell SSPMS (PL021) or PrimeCell SSP
(PL020).
1.1.1 Features of the PrimeCell SSP
The PrimeCell SSP has the following features:
• Compliance to the AMBA Specification (Rev 2.0) for easy integration into SoC
implementation.
• Master or slave operation.
• Programmable clock bit rate and prescale.
• Separate transmit and receive first-in, first-out memory buffers, 16 bits wide, 8 locations
deep.
• Programmable choice of interface operation, SPI, Microwire, or TI synchronous serial.
• Programmable data frame size from 4 to 16 bits.
• Independent masking of transmit FIFO, receive FIFO, and receive overrun interrupts.
Introduction
• Internal loopback test mode available.
• Support for Direct Memory Access (DMA).
• Identification registers that uniquely identify the PrimeCell SSP. An operating system can
use these to automatically configure itself.
Figure 1-1 shows a block diagram of the PrimeCell SSP.
SSPTXINTR
PRESETn PWDATAIn[15:0] SSPTXINTR
PSEL Tx FIFO
16 bits wide,
PENABLE PCLK 8 locations
deep TxRdDataIn[15:0]
PWRITE FIFO
AMBA status
APB SSPINTR
PADDR[11:2] and
interface RxFRdData interrupt
SSPRXINTR
PWDATA[15:0] [15:0] generation
SSPRORINTR
PRDATA[15:0] Rx FIFO SSPRTINTR
16 bits wide,
8 locations PCLK
PCLK
PCLK deep
SSPRTRINTR
SSPRORINTR
DATAIN DATAOUT SSPRXINTR
SSPCLK nSSPOE
SSPCLK
SSPTXD
PCLK SSPCLK Tx/Rx params
Register Clock
nSSPRST Prescale value SSPCLKDIV SSPFSSOUT
block prescaler
SSPCLKOUT
Transmit and
SSPRXDMACLR receive logic nSSPCTLOE
SSPTXDMACLR SSPCLKIN
SSPRXDMASREQ SSPFSSIN
DMA Tx/Rx FIFO watermark levels
SSPRXDMABREQ interface SSPRXD
RxWrData[15:0]
SSPTXDMASREQ
SSPTXDMABREQ
Figure 1-1 PrimeCell SSP block diagram
Note
For clarity, Figure 1-1 does not show the test logic.
Introduction
1.1.2 Programmable parameters
You can program the following parameters:

• master or slave mode
• enabling of operation
• frame format
• communication baud rate
• clock phase and polarity
• data widths from 4 to 16 bits wide
• interrupt masking.
1.1.3 SPI features
The features of the Motorola SPI-compatible interface are:

• full duplex, four-wire synchronous transfers
• programmable clock polarity and phase.
1.1.4 Microwire features
The National Semiconductor Microwire interface performs half-duplex transfers using an 8-bit
control message.
1.1.5 Texas Instruments synchronous serial interface features
The features of the Texas Instruments synchronous serial interface are:

• full-duplex, four-wire synchronous transfers
• transmit data pin tristateable when not transmitting.
Introduction
1.2 Product revisions

There is no product revision history available before version r1p3.
Chapter 2
Functional Overview
This chapter describes the major functional blocks of the ARM PrimeCell Synchronous Serial
Port (PL022).

• PrimeCell SSP overview on page 2-2
• PrimeCell SSP functional description on page 2-3
• PrimeCell SSP operation on page 2-6.
Functional Overview
2.1 PrimeCell SSP overview

The PrimeCell SSP is a master or slave interface for synchronous serial communication with
peripheral devices that have Motorola SPI, National Semiconductor Microwire, or Texas
Instruments synchronous serial interfaces.
The PrimeCell SSP performs serial-to-parallel conversion on data received from a peripheral
device. The CPU accesses data, control, and status information through the AMBA APB
interface. The transmit and receive paths are buffered with internal FIFO memories enabling up
to eight 16-bit values to be stored independently in both transmit and receive modes. Serial data
is transmitted on SSPTXD and received on SSPRXD.
The PrimeCell SSP includes a programmable bit rate clock divider and prescaler to generate the
serial output clock, SSPCLKOUT, from the input clock, SSPCLK. Bit rates are supported to
2MHz and higher, subject to choice of frequency for SSPCLK, and the maximum bit rate is
determined by peripheral devices.
You can use the control registers SSPCR0 and SSPCR1 to program the PrimeCell SSP operating
mode, frame format, and size. See Control register 0, SSPCR0 on page 3-4 and Control register
1, SSPCR1 on page 3-5.
The following individually maskable interrupt outputs are generated:
• SSPTXINTR requests servicing of the transmit buffer
• SSPRXINTR requests servicing of the receive buffer
• SSPRORINTR indicates an overrun condition in the receive FIFO
• SSPRTINTR indicates that a timeout period expired while data was present in the receive
FIFO.
A single combined interrupt, SSPINTR output, is asserted if any of the individual interrupts are
asserted and unmasked.
In addition to the above interrupts, a set of DMA signals are provided for interfacing with a
DMA controller.
Depending on the operating mode selected, the SSPFSSOUT output operates as:
• an active-HIGH frame synchronization output for Texas Instruments synchronous serial

frame format
• an active-LOW slave select for SPI and Microwire.
Functional Overview
2.2 PrimeCell SSP functional description

Figure 2-1 shows the PrimeCell SSP block diagram.
SSPTXINTR
PRESETn PWDATAIn[15:0] SSPTXINTR
PSEL Tx FIFO
16 bits wide,
PENABLE PCLK 8 locations
deep TxRdDataIn[15:0]
PWRITE FIFO
AMBA status
APB SSPINTR
PADDR[11:2] and
interface RxFRdData interrupt
SSPRXINTR
PWDATA[15:0] [15:0] generation
SSPRORINTR
PRDATA[15:0] Rx FIFO SSPRTINTR
16 bits wide,
8 locations PCLK
PCLK
PCLK deep
SSPRTRINTR
SSPRORINTR
DATAIN DATAOUT SSPRXINTR
SSPCLK nSSPOE
SSPCLK
SSPTXD
PCLK SSPCLK Tx/Rx params
Register Clock
nSSPRST Prescale value SSPCLKDIV SSPFSSOUT
block prescaler
SSPCLKOUT
Transmit and
SSPRXDMACLR receive logic nSSPCTLOE
SSPTXDMACLR SSPCLKIN
SSPRXDMASREQ SSPFSSIN
DMA Tx/Rx FIFO watermark levels
SSPRXDMABREQ interface SSPRXD
RxWrData[15:0]
SSPTXDMASREQ
SSPTXDMABREQ
Figure 2-1 PrimeCell SSP block diagram
Note
For clarity, Figure 2-1 does not show the test logic.
The following sections describe the functions of the PrimeCell SSP:

• AMBA APB interface on page 2-4
• Register block on page 2-4
• Clock prescaler on page 2-4
• Transmit FIFO on page 2-4
• Receive FIFO on page 2-4
• Transmit and receive logic on page 2-4
• Interrupt generation logic on page 2-5
• DMA interface on page 2-5
• Synchronizing registers and logic on page 2-5.
Functional Overview
2.2.1 AMBA APB interface
The AMBA APB interface generates read and write decodes for accesses to status and control
registers, and transmit and receive FIFO memories.
The AMBA APB is a local secondary bus that provides a low-power extension to the higher
bandwidth AMBA Advanced High-performance Bus (AHB) within the AMBA system
hierarchy. The AMBA APB groups narrow-bus peripherals to avoid loading the system bus and
provides an interface using memory-mapped registers, that are accessed under programmed
control.
2.2.2 Register block
The register block stores data written, or to be read, across the AMBA APB interface.
2.2.3 Clock prescaler
When configured as a master, an internal prescaler, comprising two free-running reloadable

serially linked counters, provides the serial output clock SSPCLKOUT.
You can program the clock prescaler, using the SSPCPSR register, to divide SSPCLK by a
factor of 2-254 in steps of two. By not utilizing the least significant bit of the SSPCPSR register,
division by an odd number is not possible and this ensures that a symmetrical, equal mark space
ratio, clock is generated. See Clock prescale register, SSPCPSR on page 3-8.
The output of the prescaler is divided again by a factor of 1-256, by programming the SSPCR0
control register, to give the final master output clock SSPCLKOUT.
2.2.4 Transmit FIFO
The common transmit FIFO is a 16-bit wide, 8-locations deep, First-In, First-Out (FIFO)
memory buffer. CPU data written across the AMBA APB interface are stored in the buffer until
read out by the transmit logic.
When configured as a master or a slave, parallel data is written into the transmit FIFO prior to
serial conversion, and transmission to the attached slave or master respectively, through the
SSPTXD pin.
2.2.5 Receive FIFO
The common receive FIFO is a 16-bit wide, 8-locations deep, first-in, first-out memory buffer.
Received data from the serial interface are stored in the buffer until read out by the CPU across
the AMBA APB interface.
When configured as a master or slave, serial data received through the SSPRXD pin is
registered prior to parallel loading into the attached slave or master receive FIFO respectively.
2.2.6 Transmit and receive logic
When configured as a master, the clock to the attached slaves is derived from a divided-down
version of SSPCLK through the prescaler operations that previous sections describe. The
master transmit logic successively reads a value from its transmit FIFO and performs parallel to
serial conversion on it. Then, the serial data stream and frame control signal, synchronized to
SSPCLKOUT, are output through the SSPTXD pin to the attached slaves. The master receive
logic performs serial to parallel conversion on the incoming synchronous SSPRXD data stream,
extracting and storing values into its receive FIFO, for subsequent reading through the APB
interface.
Functional Overview
When configured as a slave, the SSPCLKIN clock is provided by an attached master and used
to time its transmission and reception sequences. The slave transmit logic, under control of the
master clock, successively reads a value from its transmit FIFO, performs parallel to serial
conversion, then outputs the serial data stream and frame control signal through the slave
SSPTXD pin. The slave receive logic performs serial to parallel conversion on the incoming
SSPRXD data stream, extracting and storing values into its receive FIFO, for subsequent
reading through the APB interface.
2.2.7 Interrupt generation logic
The PrimeCell SSP generates four individual maskable, active-HIGH interrupts. A combined
interrupt output is also generated as an OR function of the individual interrupt requests.
You can use the single combined interrupt with a system interrupt controller that provides
another level of masking on a per-peripheral basis. This enables use of modular device drivers
that always know where to find the interrupt source control register bits.
You can also use the individual interrupt requests with a system interrupt controller that provides
masking for the outputs of each peripheral. In this way, a global interrupt controller service
routine can read the entire set of sources from one wide register in the system interrupt
controller. This is attractive where the time to read from the peripheral registers is significant
compared to the CPU clock speed in a real-time system.
The peripheral supports both the above methods.
The transmit and receive dynamic data-flow interrupts, SSPTXINTR and SSPRXINTR, are
separated from the status interrupts so that data can be read or written in response to the FIFO
trigger levels.
2.2.8 DMA interface
The PrimeCell SSP provides an interface to connect to a DMA controller. See PrimeCell DMA
interface on page 2-18 for details.
2.2.9 Synchronizing registers and logic
The PrimeCell SSP supports both asynchronous and synchronous operation of the clocks,
PCLK and SSPCLK. Synchronization registers and handshaking logic have been
implemented, and are active at all times. This has a minimal impact on performance or area.
Synchronization of control signals is performed on both directions of data flow, that is:
• from the PCLK to the SSPCLK domain
• from the SSPCLK to the PCLK domain.
Functional Overview
2.3 PrimeCell SSP operation

The following sections describe the operation of the PrimeCell SSP:
• Interface reset
• Configuring the SSP
• Enable PrimeCell SSP operation
• Clock ratios on page 2-7
• Programming the SSPCR0 Control Register on page 2-7
• Programming the SSPCR1 Control Register on page 2-8
• Frame format on page 2-8
• Texas Instruments synchronous serial frame format on page 2-9
• Motorola SPI frame format on page 2-10
• Motorola SPI Format with SPO=0, SPH=0 on page 2-10
• National Semiconductor Microwire frame format on page 2-15
• Examples of master and slave configurations on page 2-17
• PrimeCell DMA interface on page 2-18.
2.3.1 Interface reset
The PrimeCell SSP is reset by the global reset signal, PRESETn, and a block-specific reset
signal, nSSPRST. An external reset controller must use PRESETn to assert nSSPRST
asynchronously and negate it synchronously to SSPCLK. PRESETn must be asserted LOW
for a period long enough to reset the slowest block in the on-chip system, and then taken HIGH
again. The PrimeCell SSP requires PRESETn to be asserted LOW for at least one period of
PCLK.
Chapter 3 Programmer’s Model describes the values of the registers after reset.
2.3.2 Configuring the SSP
Following reset, the PrimeCell SSP logic is disabled and must be configured when in this state.
It is necessary to program control registers SSPCR0 and SSPCR1 to configure the peripheral as
a master or slave operating under one of the following protocols:
• Motorola SPI
• Texas Instruments SSI
• National Semiconductor.
The bit rate, derived from the external SSPCLK, requires the programming of the clock
prescale register SSPCPSR. See Clock prescale register, SSPCPSR on page 3-8.
2.3.3 Enable PrimeCell SSP operation
You can either prime the transmit FIFO, by writing up to eight 16-bit values when the PrimeCell
SSP is disabled, or permit the transmit FIFO service request to interrupt the CPU. Once enabled,
transmission or reception of data begins on the transmit, SSPTXD, and receive, SSPRXD, pins.
Functional Overview
2.3.4 Clock ratios
There is a constraint on the ratio of the frequencies of PCLK to SSPCLK. The frequency of
SSPCLK must be less than or equal to that of PCLK. This ensures that control signals from the
SSPCLK domain to the PCLK domain are guaranteed to get synchronized before one frame
duration:
FSSPCLK <= FPCLK.
In the slave mode of operation, the SSPCLKIN signal from the external master is
double-synchronized and then delayed to detect an edge. It takes three SSPCLKs to detect an
edge on SSPCLKIN. SSPTXD has less setup time to the falling edge of SSPCLKIN on which
the master is sampling the line.
The setup and hold times on SSPRXD, with reference to SSPCLKIN, must be more
conservative to ensure that it is at the right value when the actual sampling occurs within the
SSPMS. To ensure correct device operation, SSPCLK must be at least 12 times faster than the
maximum expected frequency of SSPCLKIN.
The frequency selected for SSPCLK must accommodate the desired range of bit clock rates.
The ratio of minimum SSPCLK frequency to SSPCLKOUT maximum frequency in the case
of the slave mode is 12, and for the master mode, it is two.
To generate a maximum bit rate of 1.8432Mbps in the master mode, the frequency of SSPCLK
must be at least 3.6864MHz. With an SSPCLK frequency of 3.6864MHz, the SSPCPSR
register must be programmed with a value of 2, and the SCR[7:0] field in the SSPCR0 register
must be programmed with a value of 0.
To work with a maximum bit rate of 1.8432Mbps in the slave mode, the frequency of SSPCLK
must be at least 22.12MHz. With an SSPCLK frequency of 22.12MHz, the SSPCPSR register
can be programmed with a value of 12, and the SCR[7:0] field in the SSPCR0 register can be
programmed with a value of 0. Similarly, the ratio of SSPCLK maximum frequency to
SSPCLKOUT minimum frequency is 254 x 256. See Control register 0, SSPCR0 on page 3-4
and Clock prescale register, SSPCPSR on page 3-8.
The minimum frequency of SSPCLK is governed by the following equations, both of which
must be satisfied:
FSSPCLK(min) => 2 x FSSPCLKOUT(max), for master mode
FSSPCLK(min) => 12 x FSSPCLKIN(max), for slave mode.
The maximum frequency of SSPCLK is governed by the following equations, both of which
must be satisfied:
FSSPCLK(max) <= 254 x 256 x FSSPCLKOUT(min), for master mode
FSSPCLK(max) <= 254 x 256 x FSSPCLKIN(min), for slave mode.
2.3.5 Programming the SSPCR0 Control Register
See Control register 0, SSPCR0 on page 3-4 for more information on the bit assignment of this
register.
The SSPCR0 register is used to:

• program the serial clock rate
• select one of the three protocols
• select the data word size, where applicable.
Functional Overview
The Serial Clock Rate (SCR) value, in conjunction with the SSPCPSR clock prescale divisor
value, CPSDVSR, is used to derive the PrimeCell SSP transmit and receive bit rate from the
external SSPCLK.
The frame format is programmed through the FRF bits, and the data word size through the DSS
bits.
Bit phase and polarity, applicable to Motorola SPI format only, are programmed through the
SPH and SPO bits.
2.3.6 Programming the SSPCR1 Control Register
See Control register 1, SSPCR1 on page 3-5, for more information on the bit assignment of this
register.
The SSPCR1 register is used to:

• select master or slave mode
• enable a loop back test feature
• enable the PrimeCell SSP peripheral.
To configure the PrimeCell SSP as a master, clear the SSPCR1 register master or slave selection
bit, MS, to 0. This is the default value on reset.
Setting the SSPCR1 register MS bit to 1 configures the PrimeCell SSP as a slave. When
configured as a slave, enabling or disabling of the PrimeCell SSP SSPTXD signal is provided
through the SSPCR1 slave mode SSPTXD output disable bit, SOD. You can use this in some
multi-slave environments where masters might parallel broadcast.
To enable the operation of the PrimeCell SSP, set the Synchronous Serial Port Enable (SSE) bit
to 1.
Bit rate generation
The serial bit rate is derived by dividing down the input clock, SSPCLK. The clock is first
divided by an even prescale value CPSDVSR in the range 2-254, and is programmed in
SSPCPSR. The clock is divided again by a value in the range 1-256, that is 1 + SCR, where SCR
is the value programmed in SSPCR0.
The following equation defines the frequency of the output signal bit clock, SSPCLKOUT:
FSSPCLK
FSSPCLKOUT =
CPSDVR x (1+SCR)
For example, if SSPCLK is 3.6864MHz, and CPSDVSR = 2, then SSPCLKOUT has a

frequency range from 7.2kHz-1.8432MHz.
2.3.7 Frame format
Each data frame is between 4-16 bits long, depending on the size of data programmed, and is
transmitted starting with the MSB. You can select the following basic frame types:
• Texas Instruments synchronous serial
• Motorola SPI
• National Semiconductor Microwire.
Functional Overview
For all formats, the serial clock, SSPCLKOUT, is held inactive while the PrimeCell SSP is idle,
and transitions at the programmed frequency only during active transmission or reception of
data. The idle state of SSPCLKOUT is utilized to provide a receive timeout indication that
occurs when the receive FIFO still contains data after a timeout period.
For Motorola SPI and National Semiconductor Microwire frame formats, the serial frame,
SSPFSSOUT, pin is active-LOW, and is asserted, pulled-down, during the entire transmission
of the frame.
For Texas Instruments synchronous serial frame format, the SSPFSSOUT pin is pulsed for one
serial clock period, starting at its rising edge, prior to the transmission of each frame. For this
frame format, both the PrimeCell SSP and the off-chip slave device drive their output data on
the rising edge of SSPCLKOUT, and latch data from the other device on the falling edge.
Unlike the full-duplex transmission of the other two frame formats, the National Semiconductor
Microwire format uses a special master-slave messaging technique, that operates at half-duplex.
In this mode, when a frame begins, an 8-bit control message is transmitted to the off-chip slave.
During this transmit, the SSS receives no incoming data. After the message has been sent, the
off-chip slave decodes it and, after waiting one serial clock after the last bit of the 8-bit control
message has been sent, responds with the requested data. The returned data can be 4-16 bits in
length, making the total frame length in the range 13-25 bits.
2.3.8 Texas Instruments synchronous serial frame format
Figure 2-2 shows the Texas Instruments synchronous serial frame format for a single
transmitted frame.
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPTXD/
MSB LSB
SSPRXD
4 to 16 bits
nSSPOE
Figure 2-2 Texas Instruments synchronous serial frame format, single transfer
In this mode, SSPCLKOUT and SSPFSSOUT are forced LOW, and the transmit data line,
SSPTXD is tristated whenever the PrimeCell SSP is idle. When the bottom entry of the transmit
FIFO contains data, SSPFSSOUT is pulsed HIGH for one SSPCLKOUT period. The value to
be transmitted is also transferred from the transmit FIFO to the serial shift register of the
transmit logic. On the next rising edge of SSPCLKOUT, the MSB of the 4-bit to 16-bit data
frame is shifted out on the SSPTXD pin. In a similar way, the MSB of the received data is
shifted onto the SSPRXD pin by the off-chip serial slave device.
Both the PrimeCell SSP and the off-chip serial slave device then clock each data bit into their
serial shifter on the falling edge of each SSPCLKOUT. The received data is transferred from
the serial shifter to the receive FIFO on the first rising edge of PCLK after the LSB has been
latched.
Figure 2-3 on page 2-10 shows the Texas Instruments synchronous serial frame format when
back-to-back frames are transmitted.
Functional Overview
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPTXD/
MSB LSB
SSPRXD
4 to 16 bits
nSSPOE (=0)
Figure 2-3 Texas Instruments synchronous serial frame format, continuous transfer
2.3.9 Motorola SPI frame format
The Motorola SPI interface is a four-wire interface where the SSPFSSOUT signal behaves as
a slave select. The main feature of the Motorola SPI format is that you can program the inactive
state and phase of the SSPCLKOUT signal using the SPO and SPH bits of the SSPSCR0
control register. See Control register 0, SSPCR0 on page 3-4.
SPO, clock polarity
When the SPO clock polarity control bit is LOW, it produces a steady state LOW value on the
SSPCLKOUT pin. If the SPO clock polarity control bit is HIGH, a steady state HIGH value is
placed on the SSPCLKOUT pin when data is not being transferred.
SPH, clock phase
The SPH control bit selects the clock edge that captures data and enables it to change state. It
has the most impact on the first bit transmitted by either permitting or not permitting a clock
transition before the first data capture edge.
When the SPH phase control bit is LOW, data is captured on the first clock edge transition.
When the SPH clock phase control bit is HIGH, data is captured on the second clock edge
transition.
2.3.10 Motorola SPI Format with SPO=0, SPH=0
Figure 2-4 and Figure 2-5 on page 2-11 show single and continuous transmission signal
sequences for Motorola SPI format with SPO=0, SPH=0. Figure 2-4 shows a single
transmission signal sequence for Motorola SPI frame format with SPO=0, SPH=0.
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPRXD MSB LSB Q

4 to 16 bits
nSSPOE
SSPTXD MSB LSB
Figure 2-4 Motorola SPI frame format, single transfer, with SPO=0 and SPH=0
Figure 2-5 on page 2-11 shows a continuous transmission signal sequence for Motorola SPI
frame format with SPO=0, SPH=0.
Functional Overview
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPTXD/
LSB MSB LSB MSB
SSPRXD
4 to 16 bits
nSSPOE (=0)
Figure 2-5 Motorola SPI frame format, continuous transfer, with SPO=0 and SPH=0
In this configuration, during idle periods:
• the SSPCLKOUT signal is forced LOW
• the SSPFSSOUT signal is forced HIGH
• the transmit data line SSPTXD is arbitrarily forced LOW
• the nSSPOE pad enable signal is forced HIGH, making the transmit pad high impedance
• when the PrimeCell SSP is configured as a master, the nSSPCTLOE line is driven LOW,
enabling the SSPCLKOUT pad, active-LOW enable
• when the PrimeCell SSP is configured as a slave, the nSSPCTLOE line is driven HIGH,
disabling the SSPCLKOUT pad, active-LOW enable.
If the PrimeCell SSP is enabled, and there is valid data within the transmit FIFO, the start of
transmission is signified by the SSPFSSOUT master signal being driven LOW. This causes
slave data to be enabled onto the SSPRXD input line of the master. The nSSPOE line is driven
LOW, enabling the master SSPTXD output pad.
One half SSPCLKOUT period later, valid master data is transferred to the SSPTXD pin. Now
that both the master and slave data have been set, the SSPCLKOUT master clock pin goes
HIGH after one additional half SSPCLKOUT period.
The data is now captured on the rising and propagated on the falling edges of the SSPCLKOUT
signal.
In the case of a single word transmission, after all bits of the data word have been transferred,
the SSPFSSOUT line is returned to its idle HIGH state one SSPCLKOUT period after the last
bit has been captured.
However, in the case of continuous back-to-back transmissions, the SSPFSSOUT signal must
be pulsed HIGH between each data word transfer. This is because the slave select pin freezes
the data in its serial peripheral register and does not permit it to be altered if the SPH bit is logic
zero. Therefore, the master device must raise the SSPFSSIN pin of the slave device between
each data transfer to enable the serial peripheral data write. On completion of the continuous
transfer, the SSPFSSOUT pin is returned to its idle state one SSPCLKOUT period after the last
Figure 2-6 on page 2-12 shows the transfer signal sequence for Motorola SPI format with
SPO=0, SPH=1, and it covers both single and continuous transfers.
Functional Overview
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPRXD Q MSB LSB Q

4 to 16 bits
nSSPOE
SSPTXD MSB LSB
Figure 2-6 Motorola SPI frame format with SPO=0 and SPH=1, single and continuous transfers
• the SSPCLKOUT signal is forced LOW
• The SSPFSSOUT signal is forced HIGH
transmission is signified by the SSPFSSOUT master signal being driven LOW. The nSSPOE
line is driven LOW, enabling the master SSPTXD output pad. After an additional one half
SSPCLKOUT period, both master and slave valid data is enabled onto their respective
transmission lines. At the same time, the SSPCLKOUT is enabled with a rising edge transition.
Data is then captured on the falling edges and propagated on the rising edges of the
SSPCLKOUT signal.
In the case of a single word transfer, after all bits have been transferred, the SSPFSSOUT line
is returned to its idle HIGH state one SSPCLKOUT period after the last bit has been captured.
For continuous back-to-back transfers, the SSPFSSOUT pin is held LOW between successive
data words and termination is the same as that of the single word transfer.
Figure 2-7 on page 2-13 and Figure 2-8 on page 2-13 show single and continuous transmission
signal sequences for Motorola SPI format with SPO=1, SPH=0.
Figure 2-7 on page 2-13 shows a single transmission signal sequence for Motorola SPI format
with SPO=1, SPH=0.
Functional Overview
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPRXD MSB LSB Q

4 to 16 bits
nSSPOE
SSPTXD MSB LSB
Figure 2-7 Motorola SPI frame format, single transfer, with SPO=1 and SPH=0
Figure 2-8 shows a continuous transmission signal sequence for Motorola SPI format with
SPO=1, SPH=0.
Note
In Figure 2-7, Q is an undefined signal.
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPTXD/
LSB MSB LSB MSB
SSPRXD
4 to 16 bits
nSSPOE (=0)
Figure 2-8 Motorola SPI frame format, continuous transfer, with SPO=1 and SPH=0
• the SSPCLKOUT signal is forced HIGH
transmission is signified by the SSPFSSOUT master signal being driven LOW, and this causes
slave data to be immediately transferred onto the SSPRXD line of the master. The nSSPOE line
is driven LOW, enabling the master SSPTXD output pad.
One half period later, valid master data is transferred to the SSPTXD line. Now that both the
master and slave data have been set, the SSPCLKOUT master clock pin becomes LOW after
one additional half SSPCLKOUT period. This means that data is captured on the falling edges
and be propagated on the rising edges of the SSPCLKOUT signal.
In the case of a single word transmission, after all bits of the data word are transferred, the
SSPFSSOUT line is returned to its idle HIGH state one SSPCLKOUT period after the last bit
has been captured.
Functional Overview
However, in the case of continuous back-to-back transmissions, the SSPFSSOUT signal must
be pulsed HIGH between each data word transfer. This is because the slave select pin freezes
the data in its serial peripheral register and does not permit it to be altered if the SPH bit is logic
zero. Therefore, the master device must raise the SSPFSSIN pin of the slave device between
each data transfer to enable the serial peripheral data write. On completion of the continuous
transfer, the SSPFSSOUT pin is returned to its idle state one SSPCLKOUT period after the last
Figure 2-9 shows the transfer signal sequence for Motorola SPI format with SPO=1, SPH=1,
and it covers both single and continuous transfers.
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPRXD Q MSB LSB Q

4 to 16 bits
nSSPOE
SSPTXD MSB LSB
Figure 2-9 Motorola SPI frame format with SPO=1 and SPH=1, single and continuous transfers
Note
In Figure 2-9, Q is an undefined signal.
• the SSPCLKOUT signal is forced HIGH
transmission is signified by the SSPFSSOUT master signal being driven LOW. The nSSPOE
line is driven LOW, enabling the master SSPTXD output pad. After an additional one half
SSPCLKOUT period, both master and slave data are enabled onto their respective transmission
lines. At the same time, the SSPCLKOUT is enabled with a falling edge transition. Data is then
captured on the rising edges and propagated on the falling edges of the SSPCLKOUT signal.
After all bits have been transferred, in the case of a single word transmission, the SSPFSSOUT
line is returned to its idle HIGH state one SSPCLKOUT period after the last bit has been
captured.
Functional Overview
For continuous back-to-back transmissions, the SSPFSSOUT pin remains in its active-LOW
state, until the final bit of the last word has been captured, and then returns to its idle state as the
previous section describes.
For continuous back-to-back transfers, the SSPFSSOUT pin is held LOW between successive
data words and termination is the same as that of the single word transfer.
2.3.14 National Semiconductor Microwire frame format
Figure 2-10 shows the National Semiconductor Microwire frame format for a single frame.
Figure 2-11 on page 2-16 shows the same format when back to back frames are transmitted.
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPTXD MSB LSB
8-bit control
SSPRXD 0 MSB LSB
4 to 16 bits
output data
nSSPOE
Figure 2-10 Microwire frame format, single transfer
Microwire format is very similar to SPI format, except that transmission is half-duplex instead
of full-duplex, using a master-slave message passing technique. Each serial transmission begins
with an 8-bit control word that is transmitted from the PrimeCell SSP to the off-chip slave
device. During this transmission, the PrimeCell SSP receives no incoming data. After the
message has been sent, the off-chip slave decodes it and, after waiting one serial clock after the
last bit of the 8-bit control message has been sent, responds with the required data. The returned
data is 4 to 16 bits in length, making the total frame length in the range 13-25 bits.

• SSPCLKOUT is forced LOW
• SSPFSSOUT is forced HIGH
• the transmit data line, SSPTXD, is arbitrarily forced LOW
• the nSSPOE pad enable signal is forced HIGH, making the transmit pad high impedance.
A transmission is triggered by writing a control byte to the transmit FIFO. The falling edge of
SSPFSSOUT causes the value contained in the bottom entry of the transmit FIFO to be
transferred to the serial shift register of the transmit logic, and the MSB of the 8-bit control
frame to be shifted out onto the SSPTXD pin. SSPFSSOUT remains LOW for the duration of
the frame transmission. The SSPRXD pin remains tristated during this transmission.
The off-chip serial slave device latches each control bit into its serial shifter on the rising edge
of each SSPCLKOUT. After the last bit is latched by the slave device, the control byte is
decoded during a one clock wait-state, and the slave responds by transmitting data back to the
PrimeCell SSP. Each bit is driven onto SSPRXD line on the falling edge of SSPCLKOUT. The
PrimeCell SSP in turn latches each bit on the rising edge of SSPCLKOUT. At the end of the
frame, for single transfers, the SSPFSSOUT signal is pulled HIGH one clock period after the
last bit has been latched in the receive serial shifter, that causes the data to be transferred to the
receive FIFO.
Functional Overview
Note
The off-chip slave device can tristate the receive line either on the falling edge of SSPCLKOUT
after the LSB has been latched by the receive shifter, or when the SSPFSSOUT pin goes HIGH.
For continuous transfers, data transmission begins and ends in the same manner as a single
transfer. However, the SSPFSSOUT line is continuously asserted, held LOW, and transmission
of data occurs back-to-back. The control byte of the next frame follows directly after the LSB
of the received data from the current frame. Each of the received values is transferred from the
receive shifter on the falling edge SSPCLKOUT, after the LSB of the frame has been latched
into the PrimeCell SSP.
Figure 2-11 shows the National Semiconductor Microwire frame format when back-to-back
frames are transmitted.
SSPCLKOUT/
SSPCLKIN
SSPFSSOUT/
SSPFSSIN
SSPTXD LSB MSB LSB
8-bit control
SSPRXD 0 MSB LSB MSB
4 to 16 bits
output data
nSSPOE
Figure 2-11 Microwire frame format, continuous transfers
Setup and hold time requirements on SSPFSSIN with respect to SSPCLKIN in

Microwire mode
In Microwire mode, the PrimeCell SSP slave samples the first bit of receive data on the rising
edge of SSPCLKIN after SSPFSSIN has gone LOW. Masters that drive a free-running
SSPCKLIN must ensure that the SSPFSSIN signal has sufficient setup and hold margins with
respect to the rising edge of SSPCLKIN.
Figure 2-12 on page 2-17 shows these setup and hold time requirements.
With respect to the SSPCLKIN rising edge on which the first bit of receive data is to be sampled
by the PrimeCell SSP slave, SSPFSSIN must have a setup of at least two times the period of
SSPCLK on which the PrimeCell SSP operates.
With respect to the SSPCLKIN rising edge previous to this edge, SSPFSSIN must have a hold
of at least one SSPCLK period.
Functional Overview
tHold=tSSPCLK tSetup=(2 x tSSPCLK)
SSPCLKIN
SSPFSSIN
SSPRXD
First RX data bit to be

sampled by SSP slave
Figure 2-12 Microwire frame format, SSPFSSIN input setup and hold requirements
2.3.15 Examples of master and slave configurations
Figure 2-13, Figure 2-14 on page 2-18, and Figure 2-15 on page 2-18 show how you can
connect the PrimeCell SSP (PL022) peripheral to other synchronous serial peripherals, when it
is configured as a master or a slave.
Note
The SSP (PL022) does not support dynamic switching between master and slave in a system.
Each instance is configured and connected either as a master or slave.
Figure 2-13 shows the PrimeCell SSP (PL022) instanced twice, as a single master and one slave.
The master can broadcast to the slave through the master SSPTXD line. In response, the slave
drives its nSSPOE signal HIGH, enabling its SSPTXD data onto the SSPRXD line of the
master.
PL022 configured as master PL022 configured as slave

SSPTXD SSPRXD
nSSPOE nSSPOE
SSPRXD SSPTXD
SSPFSSOUT SSPFSSIN
SSPFSSIN SSPFSSOUT
0V
SSPCLKOUT SSPCLKIN
nSSPCTLOE nSSPCTLOE
SSPCLKIN SSPCLKOUT
0V
Figure 2-13 PrimeCell SSP master coupled to a PL022 slave
Figure 2-14 on page 2-18 shows how an PrimeCell SSP (PL022), configured as master,
interfaces to a Motorola SPI slave. The SPI Slave Select (SS) signal is permanently tied LOW
and configures it as a slave. Similar to the above operation, the master can broadcast to the slave
through the master PrimeCell SSP SSPTXD line. In response, the slave drives its SPI MISO
port onto the SSPRXD line of the master.
Functional Overview
PL022 configured as master SPI slave

SSPTXD MOSI
nSSPOE
SSPRXD MISO
SSPFSSOUT
SSPFSSIN
0V
SSPCLKOUT SCK
nSSPCTLOE SS
0V
SSPCLKIN
0V
Figure 2-14 PrimeCell SSP master coupled to an SPI slave
Figure 2-15 shows a Motorola SPI configured as a master and interfaced to an instance of a
PrimeCell SSP (PL022) configured as a slave. In this case, the slave Select Signal (SS) is
permanently tied HIGH to configure it as a master. The master can broadcast to the slave
through the master SPI MOSI line and in response, the slave drives its nSSPOE signal LOW.
This enables its SSPTXD data onto the MISO line of the master.
SPI master PL022 configured as slave

MOSI SSPRXD
nSSPOE
MISO SSPTXD
SSPFSSIN
0V
SSPFSSOUT
SCK SSPCLKIN
nSSPCTLOE
Vdd
SS SSPCLKOUT
Figure 2-15 SPI master coupled to a PrimeCell SSP slave
2.3.16 PrimeCell DMA interface
The PrimeCell SSP provides an interface to connect to the DMA controller. The PrimeCell SSP
DMA control register, SSPDMACR controls the DMA operation of the PrimeCell SSP. See
DMA control register, SSPDMACR on page 3-12.
Functional Overview
Receive
The DMA interface includes the following signals, for receive:
SSPRXDMASREQ
Single-character DMA transfer request, asserted by the SSP. This signal is
asserted when the receive FIFO contains at least one character.
SSPRXDMABREQ
Burst DMA transfer request, asserted by the SSP. This signal is asserted when the
receive FIFO contains four or more characters.
SSPRXDMACLR
DMA request clear, asserted by the DMA controller to clear the receive request
signals. If DMA burst transfer is requested, the clear signal is asserted during the
transfer of the last data in the burst.
Transmit
The DMA interface includes the following signals, for transmit:
SSPTXDMASREQ
Single-character DMA transfer request, asserted by the SSP. This signal is
asserted when there is at least one empty location in the transmit FIFO.
SSPTXDMABREQ
Burst DMA transfer request, asserted by the SSP. This signal is asserted when the
transmit FIFO contains four characters or fewer.
SSPTXDMACLR
DMA request clear, asserted by the DMA controller, to clear the transmit request
signals. If a DMA burst transfer is requested, the clear signal is asserted during
the transfer of the last data in the burst.
The burst transfer and single transfer request signals are not mutually exclusive. They can both
be asserted at the same time. For example, when there is more data than the watermark level of
four in the receive FIFO, the burst transfer request, and the single transfer request, are asserted.
When the amount of data left in the receive FIFO is less than the watermark level, the single
request only is asserted. This is useful for situations where the number of characters left to be
received in the stream is less than a burst.
For example, if 19 characters must be received, the DMA controller then transfers four bursts
of four characters, and three single transfers to complete the stream.
Note
For the remaining three characters, the PrimeCell SSP does not assert the burst request.
Each request signal remains asserted until the relevant DMA clear signal is asserted. After the
request clear signal is deasserted, a request signal can become active again, depending on the
conditions that previous sections describe. All request signals are deasserted if the PrimeCell
SSP is disabled, or the DMA enable signal is cleared.
Functional Overview
Table 2-1 shows the trigger points for DMABREQ, for both the transmit and receive FIFOs.
Table 2-1 DMA trigger points for the transmit and receive FIFOs
Burst length
Watermark level Transmit, number of empty locations Receive, number of filled locations
1/
2 4 4
Figure 2-16 shows the timing diagram for both a single transfer request, and a burst transfer
request, with the appropriate DMA clear signal. The signals are all synchronous to PCLK.
PCLK
DMASREQ
DMABREQ
DMACLR
Figure 2-16 DMA transfer waveforms
Chapter 3
Programmer’s Model
This chapter describes the ARM PrimeCell Synchronous Serial Port (PL022) registers and
provides details needed when programming the microcontroller.

• About the programmer’s model on page 3-2
• Summary of PrimeCell SSP registers on page 3-3
• Register descriptions on page 3-4
• Interrupts on page 3-20.
3.1 About the programmer’s model

The following information applies to the Synchronous Serial Port (PL022) registers:
• The base address is not fixed, and can be different for any particular system
implementation. The offset of each register from the base address is fixed.
• Do not attempt to access reserved or unused address locations. Attempting to access these
locations can result in Unpredictable behavior.
• Unless otherwise stated in the accompanying text:

— do not modify undefined register bits
— ignore undefined register bits on reads
— all register bits are reset to a logic 0 by a system or power-on reset.
• Access type in Table 3-1 on page 3-3 is described as follows:

RW Read and write.
RO Read only.
WO Write only.
The following locations are reserved, and must not be used during normal operation:
• locations at offsets +0x028 to +0x07C and +0xFD0 to +0xFDC are reserved for possible future
extensions
• locations at offsets +0x080 to +0x088 are reserved for test purposes.
3.2 Summary of PrimeCell SSP registers

Table 3-1 shows the PrimeCell SSP registers.
Table 3-1 PrimeCell SSP register summary
Offset Name Type Reset Width Description
SSP Base + 0x00 SSPCR0 RW 0x0000 16 Control register 0, SSPCR0 on page 3-4
SSP Base + 0x04 SSPCR1 RW 0x0 4 Control register 1, SSPCR1 on page 3-5
SSP Base + 0x08 SSPDR RW 0x---- 16 Data register, SSPDR on page 3-6
SSP Base + 0x0C SSPSR RO 0x03 5 Status register, SSPSR on page 3-7
SSP Base + 0x10 SSPCPSR RW 0x00 8 Clock prescale register, SSPCPSR on page 3-8
SSP Base + 0x14 SSPIMSC RW 0x0 4 Interrupt mask set or clear register, SSPIMSC on
page 3-9
SSP Base + 0x18 SSPRIS RO 0x8 4 Raw interrupt status register, SSPRIS on page 3-10
SSP Base + 0x1C SSPMIS RO 0x0 4 Masked interrupt status register, SSPMIS on page 3-11
SSP Base + 0x20 SSPICR WO 0x0 4 Interrupt clear register, SSPICR on page 3-11
SSP Base + 0x24 SSPDMACR RW 0x0 2 DMA control register, SSPDMACR on page 3-12
SSP Base + 0x28 to 0x7C - - - - Reserved
SSP Base + 0x80 to 0x8C - - - - Reserved for test
SSP Base + 0x90 to 0xFCC - - - - Reserved
SSP Base + 0xFD0 to 0xFDC - - - - Reserved for future expansion
SSP base + 0xFEO SSPPeriphID0 RO 0x22 8 Peripheral identification registers, SSPPeriphID0-3 on

page 3-13
SSP base + 0xFE4 SSPPeriphID1 RO 0x10 8
SSP base + 0xFE8 SSPPeriphID2 RO 0x24 8
SSP base + 0xFEC SSPPeriphID3 RO 0x00 8
SSP base + 0xFF0 SSPPCellID0 RO 0x0D 8 PrimeCell identification registers, SSPPCellID0-3 on

page 3-16
SSP base + 0xFF4 SSPPCellID1 RO 0xF0 8
SSP base + 0xFF8 SSPPCellID2 RO 0x05 8
SSP base + 0xFFC SSPPCellID3 RO 0xB1 8
3.3 Register descriptions

This section describes the PrimeCell SSP registers. Table 3-1 on page 3-3 provides cross
references to individual registers.
3.3.1 Control register 0, SSPCR0
The SSPCR0 Register characteristics are:
Purpose SSPCR0 is control register 0 and contains five bit fields that control
various functions within the PrimeCell SSP.
Usage constraints There are no usage constraints.
Configurations Available in all SSP configurations.
Attributes See Table 3-1 on page 3-3.
Figure 3-1 shows the bit assignments.
15 8 7 6 5 4 3 0
SCR FRF DSS
SPO
SPH
Figure 3-1 SSPCR0 Register bit assignments
Table 3-2 shows the bit assignments.
Table 3-2 SSPCR0 Register bit assignments
Bits Name Function
[15:8] SCR Serial clock rate. The value SCR is used to generate the transmit
and receive bit rate of the PrimeCell SSP. The bit rate is:
FSSPCLK
CPSDVR x (1+SCR)
where CPSDVSR is an even value from 2-254, programmed

through the SSPCPSR register and SCR is a value from 0-255.
[7] SPH SSPCLKOUT phase, applicable to Motorola SPI frame format

only. See Motorola SPI frame format on page 2-10.
Table 3-2 SSPCR0 Register bit assignments (continued)
Bits Name Function
[6] SPO SSPCLKOUT polarity, applicable to Motorola SPI frame

format only. See Motorola SPI frame format on page 2-10.
[5:4] FRF Frame format:

00 Motorola SPI frame format.
01 TI synchronous serial frame format.
10 National Microwire frame format.
11 Reserved, undefined operation.
[3:0] DSS Data Size Select:

0011 4-bit data.
0100 5-bit data.
0101 6-bit data.
0110 7-bit data.
0111 8-bit data.
1000 9-bit data.
1001 10-bit data.
1010 11-bit data.
1011 12-bit data.
1100 13-bit data.
1101 14-bit data.
1110 15-bit data.
1111 16-bit data.
3.3.2 Control register 1, SSPCR1
Purpose SSPCR1 is the control register 1 and contains four different bit fields, that
control various functions within the PrimeCell SSP.
15 4 3 2 1 0
Reserved
SOD
MS
SSE
LBM
Figure 3-2 SSPCR1 Register bit assignments
Table 3-3 SSPCR1 Register bit assignments
Bits Name Function
[15:4] - Reserved, read unpredictable, should be written as 0.
[3] SOD Slave-mode output disable. This bit is relevant only in the slave mode, MS=1. In multiple-slave systems, it is
possible for an PrimeCell SSP master to broadcast a message to all slaves in the system while ensuring that only
one slave drives data onto its serial output line. In such systems the RXD lines from multiple slaves could be tied
together.
To operate in such systems, the SOD bit can be set if the PrimeCell SSP slave is not supposed to drive the SSPTXD
line:
0 SSP can drive the SSPTXD output in slave mode.
1 SSP must not drive the SSPTXD output in slave mode.
[2] MS Master or slave mode select.

This bit can be modified only when the PrimeCell SSP is disabled, SSE=0:
0 Device configured as master, default.
1 Device configured as slave.
[1] SSE Synchronous serial port enable:

0 SSP operation disabled.
1 SSP operation enabled.
[0] LBM Loop back mode:

0 Normal serial port operation enabled.
1 Output of transmit serial shifter is connected to input of receive serial shifter internally.
3.3.3 Data register, SSPDR
Purpose SSPDR is the data register and is 16-bits wide. When SSPDR is read, the
entry in the receive FIFO, pointed to by the current FIFO read pointer, is
accessed. As data values are removed by the PrimeCell SSP receive logic
from the incoming data frame, they are placed into the entry in the receive
FIFO, pointed to by the current FIFO write pointer.
When SSPDR is written to, the entry in the transmit FIFO, pointed to by
the write pointer, is written to. Data values are removed from the transmit
FIFO one value at a time by the transmit logic. It is loaded into the transmit
serial shifter, then serially shifted out onto the SSPTXD pin at the
programmed bit rate.
When a data size of less than 16 bits is selected, the user must right-justify
data written to the transmit FIFO. The transmit logic ignores the unused
bits. Received data less than 16 bits is automatically right-justified in the
receive buffer.
Figure 3-3 on page 3-7 shows the bit assignments.
15 0
Data
Figure 3-3 SSPDR Register bit assignments
Table 3-4 SSPDR Register bit assignments
Bits Name Function
[15:0] DATA Transmit/Receive FIFO:

Read Receive FIFO.
Write Transmit FIFO.
You must right-justify data when the PrimeCell SSP is programmed for a data size that is less than 16
bits. Unused bits at the top are ignored by transmit logic. The receive logic automatically right-justifies.
3.3.4 Status register, SSPSR
The SSPSR Register characteristics are:
Purpose SSPSR is a RO status register that contains bits that indicate the FIFO fill
status and the PrimeCell SSP busy status.
15 5 4 3 2 1 0
Reserved
BSY
RFF
RNE
TNF
TFE
Figure 3-4 SSPSR Register bit assignments
Table 3-5 SSPSR Register bit assignments
Bits Name Function
[15:5] - Reserved, read unpredictable, should be written as 0.
[4] BSY PrimeCell SSP busy flag, RO:

0 SSP is idle.
1 SSP is currently transmitting and/or receiving a frame or the transmit FIFO is not
empty.
[3] RFF Receive FIFO full, RO:

0 Receive FIFO is not full.
1 Receive FIFO is full.
[2] RNE Receive FIFO not empty, RO:

0 Receive FIFO is empty.
1 Receive FIFO is not empty.
[1] TNF Transmit FIFO not full, RO:

0 Transmit FIFO is full.
1 Transmit FIFO is not full.
[0] TFE Transmit FIFO empty, RO:

0 Transmit FIFO is not empty.
1 Transmit FIFO is empty.
3.3.5 Clock prescale register, SSPCPSR
The SSPCPSR Register characteristics are:
Purpose SSPCPSR is the clock prescale register and specifies the division factor by
which the input SSPCLK must be internally divided before further use.
The value programmed into this register must be an even number between
2-254. The least significant bit of the programmed number is hard-coded
to zero. If an odd number is written to this register, data read back from
this register has the least significant bit as zero.
15 8 7 0
Reserved CPSDVSR
Figure 3-5 SSPCPSR Register bit assignments
Table 3-6 SSPCPSR Register bit assignments
Bits Name Function
[15:8] - Reserved, read unpredictable, must be written as 0.
[7:0] CPSDVSR Clock prescale divisor. Must be an even number from 2-254, depending on the
frequency of SSPCLK. The least significant bit always returns zero on reads.
3.3.6 Interrupt mask set or clear register, SSPIMSC
The SSPIMSC Register characteristics are:
Purpose The SSPIMSC register is the interrupt mask set or clear register. It is a RW
register.
On a read this register gives the current value of the mask on the relevant
interrupt. A write of 1 to the particular bit sets the mask, enabling the
interrupt to be read. A write of 0 clears the corresponding mask.
All the bits are cleared to 0 when reset.
15 4 3 2 1 0
Reserved
TXIM
RXIM
RTIM
RORIM
Figure 3-6 SSPIMSC Register bit assignments
Table 3-7 SSPIMSC Register bit assignments
Bits Name Function
[15:4] Reserved Reserved, read as zero, do not modify.
[3] TXIM Transmit FIFO interrupt mask:

0 Transmit FIFO half empty or less condition interrupt is masked.
1 Transmit FIFO half empty or less condition interrupt is not masked.
Table 3-7 SSPIMSC Register bit assignments (continued)
Bits Name Function
[2] RXIM Receive FIFO interrupt mask:

0 Receive FIFO half full or less condition interrupt is masked.
1 Receive FIFO half full or less condition interrupt is not masked.
[1] RTIM Receive timeout interrupt mask:

0 Receive FIFO not empty and no read prior to timeout period interrupt is masked.
1 Receive FIFO not empty and no read prior to timeout period interrupt is not masked.
[0] RORIM Receive overrun interrupt mask:

0 Receive FIFO written to while full condition interrupt is masked.
1 Receive FIFO written to while full condition interrupt is not masked.
3.3.7 Raw interrupt status register, SSPRIS
The SSPRIS Register characteristics are:
Purpose The SSPRIS register is the raw interrupt status register. It is a RO register.
On a read this register gives the current raw status value of the
corresponding interrupt prior to masking. A write has no effect.
15 4 3 2 1 0
Reserved
TXRIS
RXRIS
RTRIS
RORRIS
Figure 3-7 SSPRIS Register bit assignments
Table 3-8 SSPRIS Register bit assignments
Bits Name Function
[15:4] Reserved Reserved, read as zero, do not modify
[3] TXRIS Gives the raw interrupt state, prior to masking, of the SSPTXINTR interrupt
[2] RXRIS Gives the raw interrupt state, prior to masking, of the SSPRXINTR interrupt
[1] RTRIS Gives the raw interrupt state, prior to masking, of the SSPRTINTR interrupt
[0] RORRIS Gives the raw interrupt state, prior to masking, of the SSPRORINTR interrupt
3.3.8 Masked interrupt status register, SSPMIS
The SSPMIS Register characteristics are:
Purpose The SSPMIS register is the masked interrupt status register. It is a RO

register. On a read this register gives the current masked status value of the
corresponding interrupt. A write has no effect.
15 4 3 2 1 0
Reserved
TXMIS
RXMIS
RTMIS
RORMIS
Figure 3-8 SSPMIS Register bit assignments
Table 3-9 SSPMIS Register bit assignments
Bits Name Function
[3] TXMIS Gives the transmit FIFO masked interrupt state, after masking, of the SSPTXINTR interrupt
[2] RXMIS Gives the receive FIFO masked interrupt state, after masking, of the SSPRXINTR interrupt
[1] RTMIS Gives the receive timeout masked interrupt state, after masking, of the SSPRTINTR interrupt
[0] RORMIS Gives the receive over run masked interrupt status, after masking, of the SSPRORINTR interrupt
3.3.9 Interrupt clear register, SSPICR
The SSPICR Register characteristics are:
Purpose The SSPICR register is the interrupt clear register and is write-only. On a
write of 1, the corresponding interrupt is cleared. A write of 0 has no
effect.
15 2 1 0
Reserved
RTIC
RORIC
Figure 3-9 SSPICR Register bit assignments
Table 3-10 shows the bit assignment.
Table 3-10 SSPICR Register bit assignments
Bits Name Function
[1] RTIC Clears the SSPRTINTR interrupt
[0] RORIC Clears the SSPRORINTR interrupt
3.3.10 DMA control register, SSPDMACR
The SSPDMACR Register characteristics are:
Purpose The SSPDMACR register is the DMA control register. It is a RW register.

All the bits are cleared to 0 on reset.
15 2 1 0
Reserved
TXDMAE
RXDMAE
Figure 3-10 SSPDMACR Register bit assignments
Table 3-11 SSPDMACR Register bit assignments
Bits Name Function
[15:2] Reserved Reserved, read as zero, do not modify.
[1] TXDMAE Transmit DMA Enable. If this bit is set to 1, DMA for the transmit FIFO is enabled.
[0] RXDMAE Receive DMA Enable. If this bit is set to 1, DMA for the receive FIFO is enabled.
3.3.11 Peripheral identification registers, SSPPeriphID0-3
The SSPPeriphID0-3 Registers characteristics are:
Purpose The SSPPeriphID0-3 registers are four 8-bit registers, that span address
locations 0xFE0 to 0xFEC. The registers can conceptually be treated as a
single 32-bit register. The RO registers provide the following options for
the peripheral:
PartNumber[11:0]
This is used to identify the peripheral. The three digits product
code 0x022 is used.
Designer ID[19:12]
This is the identification of the designer. ARM Ltd is 0x41,
ASCII A.
Revision[23:20]
This is the revision number of the peripheral. The number starts
from 0 and is revision dependent.
Configuration[31:24]
This is the configuration option of the peripheral. The
configuration value is 0.
Actual register Revision Part

bit assignment Configuration number Designer 1 Designer 0 number 1 Part number 0
7 07 43 07 43 07 0
31 24 23 20 19 16 15 12 11 87 0
Conceptual register Configuration Revision Designer Part number

bit assignment number
Figure 3-11 Peripheral identification Register bit assignments
Note
When you design a systems memory map, you must remember that the register has a
4KB-memory footprint. All memory accesses to the peripheral identification registers must be
32-bit, using the LDR and STR instructions.
The following subsections describe the four 8-bit peripheral identification registers:
• SSPPeriphID0 register on page 3-14
• SSPPeriphID3 register on page 3-15.
SSPPeriphID0 register
The SSPPeriphID0 Register characteristics are:
Purpose The SSPPeriphID0 register is hard-coded and the fields within the register
determine the reset value.
15 8 7 0
Reserved PartNumber0
Figure 3-12 SSPPeriphID0 Register bit assignments
Table 3-12 SSPPeriphID0 Register bit assignments
Bits Name Description
[15:8] Reserved Reserved, read undefined must read as zeros
[7:0] PartNumber0 These bits read back as 0x22
15 8 7 4 3 0
Reserved Designer0
PartNumber1
[15:8] Reserved Reserved, read undefined, must read as zeros
[7:4] Designer0 These bits read back as 0x1
[3:0] PartNumber1 These bits read back as 0x0
15 8 7 4 3 0
Reserved Revision Designer1
[7:4] Revision These bits return the peripheral revision
[3:0] Designer1 These bits read back as 0x4
15 8 7 0
Reserved Configuration
[7:0] Configuration These bits read back as 0x00
3.3.12 PrimeCell identification registers, SSPPCellID0-3
The SSPPCellID0-3 Registers characteristics are:
Purpose The SSPPCellID0-3 registers are four 8-bit wide registers, that span
address locations 0xFF0-0xFFC. The registers can conceptually be treated as
a 32-bit register. The register is used as a standard cross-peripheral
identification system. The SSPPCellID register is set to 0xB105F00D.
Actual register
bit assignment SSPPCellID3 SSPPCellID2 SSPPCellID1 SSPPCellID0
7 07 07 07 0
31 24 23 16 15 87 0
Conceptual register SSPPCellID3 SSPPCellID2 SSPPCellID1 SSPPCellID0

bit assignment
Figure 3-16 PrimeCell identification Register bit assignments
The following subsections describe the four, 8-bit PrimeCell identification registers:
• SSPPCellID0 register
• SSPPCellID1 register on page 3-17
• SSPPCellID2 register on page 3-18
• SSPPCellID3 register on page 3-18.
SSPPCellID0 register
The SSPPCellID0 Register characteristics are:
Purpose The SSPPCellID0 register is hard-coded and the fields within the register
15 8 7 0
Reserved SSPPCellID0
Figure 3-17 SSPPCellID0 Register bit assignments
Table 3-16 SSPPCellID0 Register bit assignments
[7:0] SSPPCellID0 These bits read back as 0x0D
15 8 7 0
[7:0] SSPPCellID1 These bits read back as 0xF0
15 8 7 0
[7:0] SSPPCellID2 These bits read back as 0x05
15 8 7 0
[7:0] SSPPCellID3 These bits read back as 0xB1
3.4 Interrupts
There are five interrupts generated by the PrimeCell SSP. Four of these are individual,
maskable, active-HIGH interrupts as follows:
SSPRXINTR PrimeCell SSP receive FIFO service interrupt request. See SSPRXINTR.
SSPTXINTR PrimeCell SSP transmit FIFO service interrupt request. See SSPTXINTR.
SSPRORINTR PrimeCell SSP receive overrun interrupt request. See SSPRORINTR.
SSPRTINTR PrimeCell SSP time out interrupt request. See SSPRTINTR.
The fifth is a combined single interrupt SSPINTR. See SSPINTR on page 3-21.
You can mask each of the four individual maskable interrupts by setting the appropriate bits in
the SSPIMSC register. Setting the appropriate mask bit HIGH enables the interrupt.
Provision of the individual outputs in addition to a combined interrupt output, enables the use
of either a global interrupt service routine, or modular device drivers to handle interrupts.
The transmit and receive dynamic dataflow interrupts SSPTXINTR and SSPRXINTR have
been separated from the status interrupts, so that data can be read or written in response to only
the FIFO trigger levels.
The status of the individual interrupt sources can be read from SSPRIS and SSPMIS registers.
3.4.1 SSPRXINTR
The receive interrupt is asserted when there are four or more valid entries in the receive FIFO.
3.4.2 SSPTXINTR
The transmit interrupt is asserted when there are four or fewer valid entries in the transmit FIFO.
The transmitter interrupt SSPTXINTR is not qualified with the PrimeCell SSP enable signal,
and this enables operation in either of the following ways:
• data can be written to the transmit FIFO prior to enabling the PrimeCell SSP and the
interrupts
• the PrimeCell SSP and interrupts can be enabled so that data can be written to the transmit
FIFO by an interrupt service routine.
3.4.3 SSPRORINTR
The receive overrun interrupt SSPORINTR is asserted when the FIFO is already full and an
additional data frame is received, causing an overrun of the FIFO. Data is over-written in the
receive shift register, but not the FIFO.
3.4.4 SSPRTINTR
The receive timeout interrupt is asserted when the receive FIFO is not empty and the PrimeCell
SSP has remained idle for a fixed 32 bit period. This mechanism ensures that the user is aware
that data is still present in the receive FIFO and requires servicing. This interrupt is deasserted
if the receive FIFO becomes empty by subsequent reads, or if new data is received on SSPRXD.
It can also be cleared by writing to the RTIC bit in the SSPICR register.
3.4.5 SSPINTR
The interrupts are also combined into a single output SSPINTR, that is, an OR function of the
individual masked sources. You can connect this output to the system interrupt controller to
provide another level of masking on an individual per-peripheral basis.
The combined PrimeCell SSP interrupt is asserted if any of the four individual interrupts above
are asserted and enabled.
Chapter 4
Programmer’s Model for Test
This chapter describes the additional logic for integration testing.

• PrimeCell SSP test harness overview on page 4-2
• Scan testing on page 4-3
• Test registers on page 4-4
• Integration testing of block inputs on page 4-8
• Integration testing of block outputs on page 4-10
• Integration test summary on page 4-13.
4.1 PrimeCell SSP test harness overview

The additional logic for integration vectors permits:
• capture of input signals to the block
• stimulation of the output signals.
The integration vectors provide a way of verifying that the PrimeCell SSP is correctly wired into
a system. This is done by separately testing three groups of signals:
AMBA signals These are tested by checking the connections of all the address and data
bits.
Primary input and output signals

These are tested using a simple trickbox that can demonstrate the correct
connection of the input and output signals to external pads.
Intra-chip signals, such as interrupt sources

The tests for these signals are system-specific, and enable you to write the
necessary tests. Additional logic is implemented enabling you to read and
write to each intra-chip input and output signal.
The test registers control these test features. This enables you to test the PrimeCell SSP in
isolation from the rest of the system using only transfers from the AMBA APB.
Off-chip test vectors are supplied using a 32-bit parallel External Bus Interface (EBI) and
converted to internal AMBA bus transfers. The Test Interface Controller (TIC) AMBA bus
master module controls the application of test vectors.
4.2 Scan testing

The PrimeCell SSP has been designed to simplify:
• insertion of scan test cells
• use of Automatic Test Pattern Generation (ATPG).
This is the recommended method of manufacturing test.
4.3 Test registers

Table 4-1 shows how the PrimeCell SSP test registers are memory-mapped.
Table 4-1 Test registers memory map
Offset Name Type Reset Width Description
SSP Base + 0x080 SSPTCR RW 0x0 2 Test control register, SSPTCR
SSP Base + 0x084 SSPITIP RW 0x00 5 Integration test input register, SSPITIP on page 4-5
SSP Base + 0x088 SSPITOP RW 0x0000 14 Integration test output register, SSPITOP on page 4-5
SSP Base + 0x08C SSPTDR RW 0x0000 16 Test data register, SSPTDR on page 4-7
4.3.1 Test control register, SSPTCR
The SSPTCR Register characteristics are:
Purpose SSPTCR is the test control register. This general test register controls
operation of the PrimeCell SSP under test conditions.
Attributes See Table 4-1.
15 2 1 0
Reserved
TESTFIFO
ITEN
Figure 4-1 SSPTCR Register bit assignments
Table 4-2 SSPTCR Register bit assignments
[15:2] - Reserved.
[1] TESTFIFO Test FIFO enable:

0 When this bit is 0, data cannot be read directly from the transmit FIFO
or written directly to the receive FIFO, normal operation.
1 When this bit is 1, a write to the SSPTDR writes data into the receive
FIFO, and reads from the SSPTDR reads data out of the transmit FIFO.
The reset value is 0.
[0] ITEN Integration test enable:

0 When this bit is 0, it is in normal mode.
1 When this bit is 1, the PrimeCell SSP is placed in integration test mode.
4.3.2 Integration test input register, SSPITIP
The SSPITIP Register characteristics are:
Purpose SSPITIP is the integration test input register. It is a RW register. In

integration test mode, it enables inputs to be both written to and read from.
15 5 4 3 2 1 0
Reserved
SSPTXDMACLR
SSPRXDMACLR
SSPCLKIN
SSPFSSIN
SSPRXD
Figure 4-2 SSPITIP Register bit assignments
Table 4-3 SSPITIP Register bit assignments
[15:5] - Reserved.
[4] SSPTXDMACLR Writes to this bit specify the value to be driven on the intra-chip input,
SSPTXDMACLR, in the integration test mode.
Reads return the value of SSPTXDMACLR at the output of the test multiplexor.
[3] SSPRXDMACLR Writes to this bit specify the value to be driven on the intra-chip input,
SSPRXDMACLR, in the integration test mode.
Reads return the value of SSPRXDMACLR at the output of the test multiplexor.
[2] SSPCLKIN Reads return the value of the SSPCLKIN primary input.
[1] SSPFSSIN Reads return the value of the SSPFSSIN primary input.
[0] SSPRXD Reads return the value of the SSPRXD primary input.
4.3.3 Integration test output register, SSPITOP
The SSPITOP Register characteristics are:
Purpose SSPITOP is the integration test output register. The primary outputs are
hard-coded, and the intra-chip outputs are RW. In integration test mode, it
enables outputs to be both written to and read from.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Reserved SSPTXD
SSPTXDMASREQ SSPFSSOUT
SSPTXDMABREQ SSPCLKOUT
SSPRXDMASREQ nSSPCTLOE
SSPRXDMABREQ nSSPOE
SSPINTR SSPRORINTR
SSPTXINTR SSPRTINTR
SSPRXINTR
Figure 4-3 SSPITOP Register bit assignments
Table 4-4 SSPITOP Register bit assignments
[15:14] - Reserved.
[13] SSPTXDMASREQ Intra-chip output:

• writes specify the value to be driven on the SSPTXDMASREQ line in the integration test
mode
• reads return the value of SSPTXDMASREQ at the output of the test multiplexor.
[12] SSPTXDMABREQ Intra-chip output:

• writes specify the value to be driven on the SSPTXDMABREQ line in the integration test
mode
• reads return the value of SSPTXDMABREQ at the output of the test multiplexor.
[11] SSPRXDMASREQ Intra-chip output:

• writes specify the value to be driven on the SSPRXDMASREQ line in the integration test
mode
• reads return the value of SSPRXDMASREQ at the output of the test multiplexor.
[10] SSPRXDMABREQ Intra-chip output:

• writes specify the value to be driven on the SSPRXDMABREQ line in the integration test
mode
• reads return the value of SSPRXDMABREQ at the output of the test multiplexor.
[9] SSPINTR Intra-chip output:

• writes specify the value to be driven on the SSPINTR line in the integration test mode
• reads return the value of SSPINTR at the output of the test multiplexor.
[8] SSPTXINTR Intra-chip output:

• writes specify the value to be driven on the SSPTXINTR line in the integration test mode
• reads return the value of SSPTXINTR at the output of the test multiplexor.
[7] SSPRXINTR Intra-chip output:

• writes specify the value to be driven on the SSPRXINTR line in the integration test mode
• reads return the value of SSPRXINTR at the output of the test multiplexor.
Table 4-4 SSPITOP Register bit assignments (continued)
[6] SSPRTINTR Intra-chip output:

• writes specify the value to be driven on the SSPRTINTR line in the integration test mode
• reads return the value of SSPRTINTR at the output of the test multiplexor.
[5] SSPRORINTR Intra-chip output:

• writes specify the value to be driven on the SSPRORINTR line in the integration test mode
• reads return the value of SSPRORINTR at the output of the test multiplexor.
[4] nSSPOE Primary output.

Writes specify the value to be driven on the nSSPOE line in the integration test mode.
[3] nSSPCTLOE Primary output.

Writes specify the value to be driven on the nSSPCTLOE line in the integration test mode.
[2] SSPCLKOUT Primary output.

Writes specify the value to be driven on the SSPCLKOUT line in the integration test mode.
[1] SSPFSSOUT Primary output.

Writes specify the value to be driven on the SSPFSSOUT line in the integration test mode.
[0] SSPTXD Primary output.

Writes specify the value to be driven on the SSPTXD line in the integration test mode.
4.3.4 Test data register, SSPTDR
The SSPTDR Register characteristics are:
Purpose SSPTDR is the test data register. It enables data to be written into the
receive FIFO and read out from the transmit FIFO for test purposes. This
test function is enabled by the TESTFIFO signal, bit 1 of the test control
register, SSPTCR.
15 0
Data
Figure 4-4 SSPTDR Register bit assignments
Table 4-5 SSPTDR Register bit assignments
[15:0] DATA When the TESTFIFO signal is asserted, data is written into the receive FIFO and read out of the transmit FIFO
4.4 Integration testing of block inputs

The following sections describe the integration testing for the block inputs:
• Intra-chip inputs
• Primary inputs on page 4-9.
4.4.1 Intra-chip inputs
Figure 4-5 explains the implementation details of the input integration test harness. The ITEN
bit is used as the control bit for the multiplexor, that is used in the read path of the
SSPTXDMACLR and SSPRXDMACLR intra-chip inputs. If the ITEN control bit is
deasserted, the SSPTXDMACLR and SSPRXDMACLR intra-chip inputs are routed as the
internal SSPTXDMACLR and SSPRXDMACLR inputs respectively, otherwise the stored
register values are driven on the internal line. All other hard-coded bits in the SSPITIP register
are connected directly to the primary input pins.
APB
SSPITIP[4:3]
Register
PCLK
To SSPITIP[4:3]
through APB interface
To PrimeCell
SSP core logic Intra-chip input pin
SSPTXDMACLR
SSPRXDMACLR
To SSPITIP[2:0]
through APB ITEN
interface
To PrimeCell Primary input pins, SSPCLKIN,

SSP core logic SSPFSSIN, SSPRXD
Figure 4-5 Input integration test harness
When you run integration tests with the PrimeCell SSP in a standalone test setup:
• Write a 1 to the ITEN bit in the control register. This selects the test path from the
SSPITIP[1:0] register bits to the SSPRXDMACLR and SSPTXDMACLR signals.
• Write a 1 and then a 0 to each of the SSPITIP[4:3] register bits, and read the same register
bits to ensure that the value written is read out.
When you run integration tests with the PrimeCell SSP as part of an integrated system:
• Write a 0 to the ITEN bit in the control register. This selects the normal path from the
external SSPRXDMACLR pin to the internal SSPRXDMACLR signal, and the path
from the external SSPTXDMACLR pin to the internal SSPTXDMACLR pin.
• Write a 1 and then a 0 to the internal test registers of the DMA controller to toggle the
SSPRXDMACLR signal connection between the DMA controller and the PrimeCell
SSP. Read from the SSPITIP[3] register bit to verify that the value written into the DMA
controller, is read out through the PrimeCell SSP. Similarly, write a 1 and then a 0 to the
internal registers of the DMA controller to toggle the SSPTXDMACLR signal
connection between the DMA controller and the PrimeCell SSP. Read from the
SSPITIP[4] register bit to verify that the value written into the DMA controller, is read
out through the PrimeCell SSP.
4.4.2 Primary inputs
The following primary inputs are tested using the integration vector trickbox, by looping back
the primary inputs as follows:
• SSPTXD to SSPRXD
• SSPCLKOUT to SSPCLKIN
• SSPFSSOUT to SSPFSSIN.
Write a 1 to the ITEN bit in the SSPTCR control register. 1s and 0s are driven onto the primary
output lines through the SSPITOP[4:0] register bits, that include the enable signals, and read
back through the SSPITIP[2:0] register bits.
4.5 Integration testing of block outputs

The following sections describe the integration testing for the block outputs:
• Intra-chip outputs
• Primary outputs on page 4-11.
4.5.1 Intra-chip outputs
Use this test for the following outputs:

• SSPTXDMASREQ
• SSPTXDMABREQ
• SSPRXDMASREQ
• SSPRXDMABREQ
• SSPINTR
• SSPTXINTR
• SSPRXINTR
• SSPRTINTR
• SSPRORINTR
When you run integration tests with the PrimeCell SSP in a standalone test setup:
SSPITOP[13:5] register bits to the intra-chip output signals.
• Write a 1 and then a 0 to the SSPITOP[13:5] register bits, and read the same register bits
to verify that the value written is read out.
When you run integration tests with the PrimeCell SSP as part of an integrated system:
SSPITOP[13:5] register bits to the intra-chip output signals.
• Write a 1 and then a 0 to the SSPITOP[13:5] register bits to toggle the signal connections
between the DMA controller and interrupt controller and the PrimeCell SSP. Read from
the internal test registers of the DMA controller and interrupt controller to verify that the
value written into the SSPITOP[13:5] register bits is read out through the PrimeCell SSP.
Figure 4-6 explains the implementation details of the output integration test harness for
intra-chip outputs.
APB SSPITOP[13:5]
Register
PCLK Intra-chip output pins
ITEN
Intra-chip outputs
from PrimeCell SSP core
Intra-chip output pins SSPITOP[13:5] to APB interface
Figure 4-6 Output integration test harness, intra-chip outputs
4.5.2 Primary outputs
Integration testing of primary outputs and primary inputs is carried out using the integration
vector trickbox. Use this test for the following outputs:
• SSPTXD
• SSPCLKOUT
• SSPFSSOUT
• nSSPCTLOE
• nSSPOE.
Note
Only the SSPTXD, SSPCLKOUT, and SSPFSSOUT signals are available at the output pads
of a typical configuration. The nSSPOE and nSSPCTLOE signals are internal connections to
the pad.
Verify the primary input and output pin connections as this section describes.
The primary outputs, SSPTXD, SSPCLKOUT, and SSPFSSOUT are directly connected to
SSPRXD, SSPCLKIN, and SSPFSSIN respectively by the integration trickbox that Figure 4-7
shows.
nSSPOE Integration vector

trickbox
SSPTXD SSPTXD SSPRXD
SSPFSSOUT SSPFSSOUT SSPFSSIN
SSPCLKOUT SSPCLKOUT SSPCLKIN
nSSPCTLOE
SSP PL022 Pads
Figure 4-7 Primary outputs routed to primary inputs
To test the nSSPOE and nSSPCTLOE connections, you can apply a weak pull-down to the
tristate pins through the trickbox.
• All the primary outputs can be accessed through the SSPITOP register. Different data
patterns are written to the output pins using the SSPITOP register.
• The looped-back data is read back through the SSPITIP register.
Figure 4-8 on page 4-12 shows implementation details of the output integration test harness in
the case of primary outputs.
SSPITOP[4:0] to APB interface
APB SSPITOP[4:0]
Register
PCLK Primary output pins
Primary outputs from PrimeCell SSP core

Register ITEN
PCLK
Figure 4-8 Output integration test harness, primary outputs
4.6 Integration test summary

Table 4-6 shows the integration test strategy for all PrimeCell SSP pins.
Table 4-6 PrimeCell SSP integration test strategy
Source or
Name Direction Test strategy
destination
PRESETn Input Reset controller Not tested using integration test vectors
PADDR [11:2] Input APB Register RW
PCLK Input APB Register RW
PENABLE Input APB Register RW
PRDATA [15:0] Output APB Register RW
PSEL Input APB Register RW
PWDATA [15:0] Input APB Register RW
PWRITE Input APB Register RW
SSPCLK Input Clock generator Not tested using integration test vectors
nSSPRST Input Reset controller Not tested using integration test vectors
SSPINTR Output Interrupt controller Using SSPITOP register
SSPRXINTR Output Interrupt controller Using SSPITOP register
SSPTXINTR Output Interrupt controller Using SSPITOP register
SSPRTINTR Output Interrupt controller Using SSPITOP register
SSPRORINTR Output Interrupt controller Using SSPITOP register
SSPTXDMASREQ Output DMA controller Using SSPITOP register
SSPRXDMASREQ Output DMA controller Using SSPITOP register
SSPTXDMABREQ Output DMA controller Using SSPITOP register
SSPRXDMABREQ Output DMA controller Using SSPITOP register
SSPTXDMACLR Input DMA controller Using SSPITIP register
SSPRXDMACLR Input DMA controller Using SSPITIP register
SCANENABLE Input Test controller Not tested using integration test vectors
SCANINPCLK Input Test controller Not tested using integration test vectors
SCANINSSPCLK Input Test controller Not tested using integration test vectors
SCANOUTPCLK Output Test controller Not tested using integration test vectors
SCANOUTSSPCLK Output Test controller Not tested using integration test vectors
SSPRXD Input PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
SSPFSSIN Input PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
SSPCLKIN Input PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
SSPTXD Output PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
Table 4-6 PrimeCell SSP integration test strategy (continued)
Source or
Name Direction Test strategy
destination
SSPFSSOUT Output PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
SSPCLKOUT Output PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
nSSPCTLOE Output PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
nSSPOE Output PAD Using integration vector trickbox and SSPITIP and SSPITOP registers
Appendix A
Signal Descriptions
This appendix describes the signals that interface with the ARM PrimeCell SSP (PL022).

• AMBA APB signals on page A-2
• On-chip signals on page A-3
• Signals to pads on page A-4.
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. A-1
Signal Descriptions
A.1 AMBA APB signals

The PrimeCell SSP module is connected to the AMBA APB as a bus slave. Table A-1 shows
the APB signals that are used and produced.
Table A-1 AMBA APB signal descriptions
Source or
Name Direction Description
destination
PRESETn Input Reset controller Bus reset signal, active-LOW.
PADDR[11:2] Input APB bridge Subset of AMBA APB address bus.
PCLK Input Clock generator AMBA APB clock, used to time all bus transfers.
PENABLE Input APB bridge AMBA APB enable signal. PENABLE is asserted HIGH for one cycle of
PCLK to enable a bus transfer.
PRDATA[15:0] Output APB bridge Unidirectional AMBA APB read data bus.
PSEL Input APB bridge PrimeCell SSP select signal from decoder. When set to 1, this signal indicates
the slave device is selected by the AMBA APB bridge, and that a data transfer
is required.
PWDATA[15:0] Input APB bridge Unidirectional AMBA APB write data bus.
PWRITE Input APB bridge AMBA APB transfer direction signal, indicates a write access when HIGH, read
access when LOW.
Signal Descriptions
A.2 On-chip signals

The reset inputs are asynchronously asserted but synchronously removed for each of the clock
domains within the PrimeCell SSP. This ensures that logic is reset even if clocks are not present,
to avoid any static power consumption problems at power-up. Each clock domain has an
individual reset to simplify the process of inserting scan test cells.
Table A-2 shows the non-AMBA signals from the block.
Table A-2 On-chip signals
Source or
destination
SSPCLK Input Clock generator Main PrimeCell SSP clock input.
nSSPRST Input Reset controller PrimeCell SSP reset signal to SSPCLK clock domain, active-LOW.
The reset controller must use PRESETn to assert nSSPRST
asynchronously, but negate it synchronously with SSPCLK.
SSPTXINTR Output Interrupt controller Transmit FIFO service request.
SSPRXINTR Output Interrupt controller Receive FIFO service request.
SSPRORINTR Output Interrupt controller PrimeCell SSP receive overrun interrupt.
SSPRTINTR Output Interrupt controller PrimeCell SSP receive timeout interrupt.
SSPINTR Output Interrupt controller PrimeCell SSP interrupt. This interrupt is an OR of the following
individual interrupts:
• SSPTXINTR
• SSPRXINTR
• SSPRTINTR
• SSPRORINTR.
SSPTXDMASREQ Output DMA controller PrimeCell SSP transmit DMA single request, active-HIGH.
SSPRXDMASREQ Output DMA controller PrimeCell SSP receive DMA single request, active-HIGH.
SSPTXDMABREQ Output DMA controller PrimeCell SSP transmit DMA burst request, active-HIGH.
SSPRXDMABREQ Output DMA controller PrimeCell SSP receive DMA burst request, active-HIGH.
SSPTXDMACLR Input DMA controller DMA request clear, asserted by the DMA controller to clear the transmit
request signals. If a DMA burst transfer is requested, the clear signal is
asserted during the transfer of the last data in the burst.
SSPRXDMACLR Input DMA controller DMA request clear, asserted by the DMA controller to clear the receive
request signals. If a DMA burst transfer is requested, the clear signal is
asserted during the transfer of the last data in the burst.
SCANENABLE Input Test controller Place holder for scan path select signal.
SCANINPCLK Input Test controller Place holder for scan data input signal, PCLK domain.
SCANOUTPCLK Output Test controller Place holder for scan data output signal, PCLK domain.
SCANINSSPCLK Input Test controller Place holder for scan data input signal, SSPCLK domain.
SCANOUTSSPCLK Output Test controller Place holder for scan data output signal, SSPCLK domain.
Signal Descriptions
A.3 Signals to pads

Table A-3 shows the signals from the PrimeCell SSP to input and output pads of the chip. It is
your responsibility to make proper use of the peripheral pins to meet the exact interface
requirements.
Table A-3 Pad signal descriptions
Source or
destination
SSPFSSOUT Output Pad PrimeCell SSP frame, or slave select output, master.
SSPCLKOUT Output Pad PrimeCell SSP clock output, master.
SSPRXD Input Pad PrimeCell SSP receive data input.
SSPTXD Output Pad PrimeCell SSP transmit data output.
nSSPCTLOE Output Pad Output enable signal, active-LOW, for SSPCLKOUT output from the PrimeCell
SSP. This output is:
• cleared when the device is in master mode
• set when the device is in slave mode.
SSPFSSIN Input Pad PrimeCell SSP frame input, slave.
SSPCLKIN Input Pad PrimeCell SSP clock input, slave.
nSSPOE Output Pad Output enable signal, active-LOW, to indicate when SSPTXD is valid.
Appendix B
Revisions
This appendix describes the technical changes between released issues of this book.
Table B-1 Differences between issue A and issue B
Change Location
Minor technical edits • Figure 1-1 on page 1-3

• Figure 2-1 on page 2-3
• Figure 2-16 on page 2-20.
Primary output test procedure revised Not known
Table B-2 Differences between issue B and issue C
Change Location

Primary input test revised Not known
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. B-1
Revisions
Table B-3 Differences between issue C and issue D
Change Location

Change to peripheral identification revision number information Peripheral identification registers, SSPPeriphID0-3 on page 3-13
Table B-4 Differences between issue D and issue E
Change Location
Updated graphic • Figure 2-2 on page 2-9

Changed text description of master and slave operation Examples of master and slave configurations on page 2-17
Clarified description for bits [3] and [4] Table 4-4 on page 4-6
Table B-5 Differences between issue E and issue F
Change Location Affects
Correction made to the timing diagram Figure 2-2 on page 2-9 r1p3
Correction made to the description after the timing diagram Texas Instruments synchronous serial frame format on r1p3
page 2-9
Correction made to the description before the timing diagram Setup and hold time requirements on SSPFSSIN with r1p3
respect to SSPCLKIN in Microwire mode on page 2-16
Updated the reset value for the Peripheral identification Table 3-1 on page 3-3 r1p3
register, SSPPeriphID2
Added register diagrams to the register descriptions Register descriptions on page 3-4 r1p3
Added register diagrams to the register descriptions Test registers on page 4-4 r1p3
Table B-6 Differences between issue F and issue G
Change Location Affects
ARM DDI 0194G Copyright © 2000-2001, 2009, 2011. All rights reserved. B-2

Arm Primecell Synchronous Serial Port (Pl022) : Technical Reference Manual

Uploaded by

Copyright:

Available Formats

Arm Primecell Synchronous Serial Port (Pl022) : Technical Reference Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Arm Primecell Synchronous Serial Port (Pl022) : Technical Reference Manual

Uploaded by

Copyright:

Available Formats

ARM PrimeCell Synchronous Serial

Technical Reference Manual

Copyright © 2000-2001, 2009, 2011. All rights reserved.

Copyright © 2000-2001, 2009, 2011. All rights reserved.

Date Issue Confidentiality Change

6 September 2000 A Non-Confidential First release

19 March 2001 B Non-Confidential Second release

15 June 2001 C Non-Confidential Third release

31 July 2001 D Non-Confidential Fourth release

30 January 2009 E Non-Confidential Unrestricted Access Fifth release

01 November 2011 F Non-Confidential Unrestricted Access Sixth release

04 November 2011 G Non-Confidential Unrestricted Access Seventh release

The information in this document is final, that is for a developed product.

Chapter 2 Functional Overview

Chapter 3 Programmer’s Model

Chapter 4 Programmer’s Model for Test

Appendix A Signal Descriptions

About this book

Product revision status

Using this book

This book is organized into the following chapters:

Chapter 2 Functional Overview

Chapter 3 Programmer’s Model

Chapter 4 Programmer’s Model for Test

Appendix A Signal Descriptions

See ARM Glossary, http://infocenter.arm.com/help/topic/com.arm.doc.aeg0014-/index.html.

Conventions that this book can use are described in:

The typographical conventions are:

italic Highlights important notes, introduces special terminology, denotes

bold Highlights interface elements, such as menu names. Denotes signal

monospace italic Denotes arguments to monospace text where the argument is to be

Bus to high impedance

High impedance to stable bus

Key to timing diagram conventions

The signal conventions are:

• LOW for active-LOW signals.

Lower-case n At the start or end of a signal name denotes an active-LOW signal.

Prefix A Denotes global Advanced eXtensible Interface (AXI) signals.

Prefix AR Denotes AXI read address channel signals.

Prefix AW Denotes AXI write address channel signals.

Prefix B Denotes AXI write response channel signals.

Prefix C Denotes AXI low-power interface signals.

Prefix H Denotes Advanced High-performance Bus (AHB) signals.

Prefix P Denotes Advanced Peripheral Bus (APB) signals.

Prefix R Denotes AXI read data channel signals.

Prefix W Denotes AXI write data channel signals.

This section lists publications by ARM and by third parties.

See Infocenter, http://infocenter.arm.com, for access to ARM documentation.

• AMBA® Specification (Rev 2.0) (ARM IHI 00011)

• ARM PrimeCell Synchronous Serial Port (PL022) Integration Manual

• ARM PrimeCell Synchronous Serial Port (PL020) Technical Reference Manual

Feedback on this product

• The product name.

• The product revision or version.

• An explanation with as much information as you can provide. Include symptoms if

Feedback on this book

ARM also welcomes general suggestions for additions and improvements.

It contains the following sections:

1.1 About the ARM PrimeCell SSP (PL022)