OSPF Neighbor SIM

R1 R2 R3
interface Loopback0 ! username R6 password
description ***Loopback*** interface Loopback0 CISCO36
ip address 192.168.1.1 description **Loopback** !
255.255.255.255 ip address 192.168.2.2 interface Loopback0
ip ospf 1 area 0 255.255.255.255 description **Loopback**
! ip ospf 2 area 0 ip address 192.168.3.3
interface Ethernet0/0 ! 255.255.255.255
description **Connected to interface Ethernet0/0 ip ospf 3 area 0
R1-LAN** description **Connected to !
ip address 10.10.110.1 R2-LAN** interface Ethernet0/0
255.255.255.0 ip address 10.10.120.1 description **Connected to
ip ospf 1 area 0 255.255.255.0 L2SW**
! ip ospf 2 area 0 ip address 10.10.230.3
interface Ethernet0/1 ! 255.255.255.0
description **Connected to interface Ethernet0/1 ip ospf 3 area 0
L2SW** description **Connected to !
ip address 10.10.230.1 L2SW** interface Serial1/0
255.255.255.0 ip address 10.10.230.2 description **Connected to
ip ospf hello-interval 25 255.255.255.0 R4-Branch1 office**
ip ospf 1 area 0 ip ospf 2 area 0 ip address 10.10.240.1
! ! 255.255.255.252
router ospf 1 router ospf 2 encapsulation ppp
log-adjacency-changes log-adjacency-changes ip ospf 3 area 0
!
interface Serial1/1
 description **Connected to
R5-Branch2 office**
ip address 10.10.240.5
255.255.255.252
encapsulation ppp
ip ospf hello-interval 50
ip ospf 3 area 0
!
interface Serial1/2
description **Connected to
R6-Branch3 office**
ip address 10.10.240.9
255.255.255.252
encapsulation ppp
ip ospf 3 area 0
ppp authentication chap
!
router ospf 3
router-id 192.168.3.3
!
R4 R5 R6
! ! username R3 password
interface Loopback0 interface Loopback0 CISCO36
description **Loopback** description **Loopback** !
ip address 192.168.4.4 ip address 192.168.5.5 interface Loopback0
255.255.255.255 255.255.255.255 description **Loopback**
ip ospf 4 area 2 ip ospf 5 area 0 ip address 192.168.6.6
! ! 255.255.255.255
interface Ethernet0/0 interface Ethernet0/0 ip ospf 6 area 0
ip address 172.16.113.1 ip address 172.16.114.1 !
255.255.255.0 255.255.255.0 interface Ethernet0/0
ip ospf 4 area 2 ip ospf 5 area 0 ip address 172.16.115.1
! ! 255.255.255.0
interface Serial1/0 interface Serial1/0 ip ospf 6 area 0
description **Connected to description **Connected to !
R3-Main Branch office** R3-Main Branch office** interface Serial1/0
ip address 10.10.240.2 ip address 10.10.240.6 description **Connected to
255.255.255.252 255.255.255.252 R3-Main Branch office**
encapsulation ppp encapsulation ppp ip address 10.10.240.10
ip ospf 4 area 2 ip ospf 5 area 0 255.255.255.252
! ! encapsulation ppp
router ospf 4 router ospf 5 ip ospf 6 area 0
log-adjacency-changes log-adjacency-changes ppp authentication chap
!
router ospf 6
router-id 192.168.3.3
!

Question 1
An OSPF neighbor adjacency is not formed between R3 in the main office and R4 in
the Branch1 office. What is causing the problem?
 A. There is an area ID mismatch.
B. There is a Layer 2 issue; an encapsulation mismatch on serial links.
C. There is an OSPF hello and dead interval mismatch.
D. The R3 router ID is configured on R4.

Answer :
We learned it is a OSPF problem so we should check the interfaces between them
first. On both R3 and R4 use “show running-config” command to check their S1/0
interfaces.

R3#show running-config
<<output omitted>>
!
interface Serial1/0
description **Connected to R4-Branch1 office**
ip address 10.10.240.1 255.255.255.252
encapsulation ppp
ip ospf 3 area 0
!
<<output omitted>>

R4#show running-config
<<output omitted>>
!
interface Serial1/0
description **Connected to R3-Main Branch office**
ip address 10.10.240.2 255.255.255.252
encapsulation ppp
ip ospf 4 area 2
!
<<output omitted>>
In the output above we see their Area IDs are mismatched; interface S1/0 of R3 is
in area 0 (R3: ip ospf 3 area 0) while interface s1/0 of R4 is in area 2 (R4: ip
ospf 4 area 2).

Question 2
An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in
the Branch2 office. What is causing the problem?

A. There is an area ID mismatch.

B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.

Answer :

Continue checking their connected interfaces with the “show running-config”

command:

R3#show running-config
<<output omitted>>
!
interface Serial1/1
description **Connected to R5-Branch2 office**
ip address 10.10.240.5 255.255.255.252
encapsulation ppp
ip ospf hello-interval 50
ip ospf 3 area 0
!
<<output omitted>>
 R5#show running-config
<<output omitted>>
!
interface Serial1/0
description **Connected to R3-Main Branch office**
ip address 10.10.240.6 255.255.255.252
encapsulation ppp
ip ospf 5 area 0
!
<<output omitted>>

The only difference we can see here is the line “ip ospf hello-interval 50” on R3.
This command sets the number of seconds R3 waits before sending the next hello
packet out this interface. In this case after configuring this command, R3 will send
hello packets to R5 every 50 seconds. But the default value of hello-interval is 10
seconds and R5 is using it. Therefore we can think of a hello interval mismatch
problem here. You can verify with the “show ip ospf interface <interface>”
command on each router.

R3#sh ip ospf int s1/1

Serial1/1 is up, line protocol is up
Internet Address 10.10.240.5/30, Area 0
Process ID 3, Router ID 192.168.3.3, Network Type POINT_TO_POINT, Cost: 64
Enabled by interface config, including secondary ip addresses
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 50, Dead 200, Wait 200, Retransmit 5
oob-resync timeout 200
Hello due in 00:00:28
Supports Link-local Signaling (LLS)
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
 Last flood scan length is 0, maximum is 0
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 0, Adjacent neighbor count is 0
Suppress hello for 0 neighbor(s)

R5#sh ip ospf int s1/0

Serial1/0 is up, line protocol is up
Internet Address 10.10.240.6/30, Area 0
Process ID 5, Router ID 10.10.240.6, Network Type POINT_TO_POINT, Cost: 64
Enabled by interface config, including secondary ip addresses
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
oob-resync timeout 40
Hello due in 00:00:04
Supports Link-local Signaling (LLS)
Index 1/1, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 0, maximum is 0
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 0, Adjacent neighbor count is 0
Suppress hello for 0 neighbor(s)

So we can see both hello and dead interval are mismatched because the dead
interval always four times the value of hello interval, unless you manually configure
the dead interval (with the ip ospf dead-interval <seconds> command).
Question 3

R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the
issue?

A. R1 ethernet0/1 is shutdown. Configure no shutdown command.

 B. R1 ethernet0/1 configured with a non-default OSPF hello interval of 25;
configure no ip ospf hello-interval 25
C. R2 ethernet0/1 and R3 ethernet0/0 are configured with a non-default OSPF
hello interval of 25; configure no ip ospf hello-interval 25
D. Enable OSPF for R1 ethernet0/1; configure ip ospf 1 area 0 command under
ethernet0/1

Answer :

Continue checking their connected interfaces with the “show running-config”

command:

R1#show running-config
<<output omitted>>
!
interface Ethernet0/1
description **Connected to L2SW**
ip address 10.10.230.1 255.255.255.0
ip ospf hello-interval 25
ip ospf 1 area 0
!
<<output omitted>>

R2#show running-config
<<output omitted>>
!
interface Ethernet0/1
description **Connected to L2SW**
ip address 10.10.230.2 255.255.255.0
ip ospf 2 area 0
!
<<output omitted>>
We see the hello interval on R1 is not the same as R2 (and you can verify with the
“show ip ospf interface <interface> command”) -> There is a hello and dead
interval mismatch problem. We should configure “no ip ospf hello-interval 25” on
R1.
Note: Maybe there are some versions of this question in the exam. For example
there are some reports saying that Ethernet0/1 on R1 is shutdown (and this is the
correct choice in the exam). So please be careful checking the config on the routers
before choosing the correct answers.

Question 4

An OSPF neighbor adjacency is not formed between R3 in the main office and R6 in
the Branch3 office. What is causing the problem?

A. There is an area ID mismatch.

B. There is a PPP authentication issue; the username is not configured on R3
and R6.
C. There is an OSPF hello and dead interval mismatch.
D. The R3 router ID is configured on R6.

Answer :

R3#show running-config
<<output omitted>>
username R6 password CISCO36
!
interface Serial1/2
description **Connected to R6-Branch3 office**
ip address 10.10.240.9 255.255.255.252
encapsulation ppp
ip ospf 3 area 0
 ppp authentication chap
!
<<output omitted>>
!
router ospf 3
router-id 192.168.3.3
!
<<output omitted>>

R6#show running-config
<<output omitted>>
username R3 password CISCO36
!
interface Serial1/0
description **Connected to R3-Main Branch office**
ip address 10.10.240.10 255.255.255.252
encapsulation ppp
ip ospf 6 area 0
ppp authentication chap
!
<<output omitted>>
!
router ospf 6
router-id 192.168.3.3
!
<<output omitted>>

We are not sure about the configuration of ppp authentication in this case. Some
reports said that only one router has the “ppp authentication chap” command but it
is just a trick and is not the problem here. The real problem here is R6 uses the
same router-id of R3 (192.168.3.3) so OSPF neighborship cannot be established. In
real life, such configuration error will be shown in the command line interface (CLI).
So please check carefully for this question.