Scribd Logo
Upload

Welcome to Scribd!

  • 86 views

    EIGRP Troubleshooting Sim CCNA 200-125 Packet Tracer PKA

    Uploaded by

    SaudDanish
    The document describes an EIGRP troubleshooting simulation involving routers R1 through R6. It includes the configurations of each router and questions to troubleshoot connectivity issues between various routers in the topology.

    Copyright:

    © All Rights Reserved

    EIGRP Troubleshooting Sim CCNA 200-125 Packet Tracer PKA

    Uploaded by

    SaudDanish
    86 views6 pages
    The document describes an EIGRP troubleshooting simulation involving routers R1 through R6. It includes the configurations of each router and questions to troubleshoot connectivity issues between various routers in the topology.

    Original Description:

    CCNA Certification Access

    Original Title

    Ccnav6.Com-EIGRP Troubleshooting Sim CCNA 200-125 Packet Tracer PKA

    Copyright

    © © All Rights Reserved

    Did you find this document useful?

    Is this content inappropriate?

    The document describes an EIGRP troubleshooting simulation involving routers R1 through R6. It includes the configurations of each router and questions to troubleshoot connectivity issues between various routers in the topology.

    Copyright:

    © All Rights Reserved
    86 views6 pages

    EIGRP Troubleshooting Sim CCNA 200-125 Packet Tracer PKA

    Uploaded by

    SaudDanish
    The document describes an EIGRP troubleshooting simulation involving routers R1 through R6. It includes the configurations of each router and questions to troubleshoot connectivity issues between various routers in the topology.

    Copyright:

    © All Rights Reserved
    of 6

    EIGRP Troubleshooting Sim – CCNA 200-125 Packet

    Tracer .PKA
    ccnav6.com/eigrp-troubleshooting-sim-ccna-200-125-packet-tracer-pka.html

    CCNA v6 Labs

    3.5 (2) votes

    EIGRP TS Sim – CCNA 200-125

    Refer to the topology. Your company has connected the routers R1, R2 and R3 with serial
    links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2
    are also connected to the routers R4 and R5.

    The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the
    EIGRP issues between the various routers. Use the appropriate show commands to
    troubleshoot the issues.

    Download Packet Tracer .pka file:


    EIGRP Troubleshooting Sim.PKA 419.89 KB
    Download

    1/6
    Instead of posting the output of show run commands we post here the commands
    entered on each router to reduce some useless lines. Also you can try solving questions by
    yourself before reading the answers.

    R1: R2: R3:


    int lo0 int lo0 int lo0
    ip address 10.1.1.1 ip address 10.2.2.2 ip address 10.3.3.3
    255.255.255.255 255.255.255.255 255.255.255.255
    int e0/0 int e0/0 int e0/0
    ip address 192.168.16.1 ip address 192.168.123.2 ip address 192.168.123.3
    255.255.255.0 255.255.255.0 255.255.255.0
    int s1/1 int s2/1 int s2/1
    ip address 192.168.13.1 ip address 192.168.12.2 ip address 192.168.13.3
    255.255.255.0 255.255.255.0 255.255.255.0
    bandwidth 1000 ! !
    int s1/3 router eigrp 1 router eigrp 1
    ip address 192.168.12.1 network 10.2.2.2 0.0.0.0 network 10.3.3.3 0.0.0.0
    255.255.255.0 network 192.168.12.0 network 192.168.13.0
    ! network 192.168.123.0 network 192.168.123.0
    router eigrp 1
    network 192.168.12.0
    network 192.168.13.0
    network 192.168.16.0

    R4: R5: R6:


    int lo0 int lo0 int lo0
    ip address 10.4.4.4 ip address 10.5.5.5 ip address 10.6.6.6
    255.255.255.255 255.255.255.255 255.255.255.255
    int lo1 int lo1 int e0/0
    ip address 10.4.4.5 ip address 10.5.5.55 ip address 192.168.16.6
    255.255.255.255 255.255.255.255 255.255.255.0
    int lo2 int e0/0 !
    ip address 10.4.4.6 ip address 192.168.123.5 router eigrp 1
    255.255.255.255 255.255.255.0 network 10.6.6.6 0.0.0.0
    int e0/0 !
    ip address 192.168.123.4 router eigrp 1
    255.255.255.0 network 10.5.5.5 0.0.0.0
    ! network 10.5.5.55 0.0.0.0
    router eigrp 2 network 10.10.10.0 0.0.0.255
    network 10.4.4.4 0.0.0.0 network 192.168.123.0
    network 10.4.4.5 0.0.0.0
    network 10.4.4.6 0.0.0.0
    network 192.168.123.0

    Note: In the exam, this sim uses IOS version 15 so no auto-summary is the default setting
    of EIGRP. You don’t have to type it.

    Question 1:
    2/6
    The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and
    10.4.4.6/32 are not appearing in the routing table of R5. Why are the interfaces missing?

    The interfaces are shutdown, so they are not being advertised.


    R4 has been incorrectly configured to be in another AS, so it does not peer with R5.*
    Automatic summarization is enabled, so only the 10.0.0.0 network is displayed.
    The loopback addresses haven’t been advertised, and the network command is
    missing on R4

    Explanation/Reference:

    On R4 we see EIGRP is configured with AS 2 (router eigrp 2) while other routers are using
    AS 1 (router eigrp 1). Therefore R4 cannot see other routers and vice versa.

    Note: There is another version of this question but the answer is D (as R4 misses the
    network 10.4.4.4 0.0.0.0 , network 10.4.4.5 0.0.0.0 and network 10.4.4.6
    0.0.0.0 statements).

    Question 2:
    Which path does traffic take from R1 to R5?

    The traffic goes through R2.*


    The traffic goes through R3.
    The traffic is equally load-balanced over R2 and R3.
    The traffic is unequally load-balanced over R2 and R3.

    Explanation/Reference:

    For this question we have to check the routing table of R1 to find out the answer.
    Use the show ip route command on R1 we will get something like this:

    3/6
    There are three interfaces on R5 which are Loopback0: 10.5.5.5 ; Loopback1: 10.5.5.55;
    Ethernet0/0: 192.168.123.5 and all of them are advertised via 192.168.12.2 so we can
    conclude traffic from R1 to R5 goes through R2 (192.168.12.2 is the IP address of S2/1
    interface of R2).

    Note: Maybe there is another version of this question in the exam in which the answer
    should be “The traffic is equally load-balanced over R2 and R3”. Therefore please check the
    show ip route output carefully to see if there are more than one route to the destination.

    Question 3:
    Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is
    the cause for this misconfiguration?

    The K values mismatch.


    The AS does not match.
    The network command is missing.*
    The passive-interface command is enabled.
    4/6
    Explanation/Reference:

    From the configuration of R6 we learn that R6 is missing “network 192.168.16.0” command


    (the network between R1 & R6) under EIGRP so EIGRP neighbor relationship will not be
    formed between them.

    Note: Please check the configuration of R6 carefully. If the “network 192.168.16.0” is not
    missing on R6 but the “metric weights” is configured like this:

    R6:
    router eigrp 1
    network 10.6.6.6 0.0.0.0
    network 192.168.16.0
    metric weights 0 0 0 1 1 1

    Then you should check if R1 has the same “metric weights” or not. If not then the answer
    should be “K values are mismatched”.

    For your information, EIGRP K values are the scale numbers that EIGRP uses in metric
    calculation . Mismatched K values can prevent neighbor relationships from being
    established. The syntax of “metric weights” command is:

    metric weights tos k1 k2 k3 k4 k5 (with tos is the type of service and must always be zero)

    Question 4:
    Study the following output taken on R1:

    R1#ping 10.5.5.55 source 10.1.1.1


    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
    Packet sent with a source address of 10.1.1.1
    . . . . .
    Success rate is 0 percent (0/5)

    Why are the pings failing?

    The network statement is missing on R5.


    The loopback interface is shut down on R5.
    The network statement is missing on R1.*
    The IP address that is configured on the Lo1 interface on R5 is incorrect.

    Explanation/Reference:

    R1 does not advertise its loopback 0 (10.1.1.1) to EIGRP therefore a ping to destination
    10.5.5.55 (R5) from 10.1.1.1 will not be successful because R5 does not know how to reply
    to R1.

    Related Articles
    Prev Article
    Next Article

    5/6
    6/6

    You might also like