ACS120

Overvoltage protected AC switch (ACS™)

Datasheet - production data

Applications
 AC static switching in appliance control
systems
&20  Drive of low power high inductive or resistive
loads like:
– Relay, valve, solenoid, dispenser
287
*
– Pump, fan, micro-motor
*
'3$. 72)3$%
287
&20 – Defrost heater
&20
Description
The ACS120 belongs to the AC line switch family.
This high performance switch circuit is able to
* control a load of up to 2 A.
&20
287
The ACS™ switch embeds a high voltage
72$%
clamping structure to absorb the inductive turn off
energy and a gate level shifter driver to separate
the digital controller from the main switch. It is
triggered with a negative gate current flowing out
Features of the gate pin.
 Blocking voltage: VDRM / VRRM = +/- 700 V Figure 1. Functional diagram
 Avalanche controlled: VCL typ. = 1100 V
287
 Nominal conducting current: IT(RMS) = 2 A
 Gate triggering current: IGT < 10 mA
 High noise immunity: static dV/dt > 500 V/µs
*
Benefits
 Needs no more external protection snubber or
varistor
 Enables equipment to meet IEC 61000-4-5
 Reduces component count up to 80% &20
&20 &RPPRQGULYHUHIHUHQFHWRFRQQHFW
 Interfaces directly with the micro controller WRWKHPDLQV
 Eliminates any gate kick back on the micro- 287 2XWSXWWRFRQQHFWWRWKHORDG
* *DWHLQSXWWRFRQQHFWWRWKHFRQWUROOHU
controller WKURXJKJDWHUHVLVWRU
 Allows straightforward connection of several
AC switches on same cooling pad

May 2016 DocID9469 Rev 4 1/17

This is information on a product in full production. www.st.com
Characteristics ACS120

1 Characteristics

Table 1. Absolute ratings (limiting values)

For either positive or negative polarity of pin OUT voltage in respect to pin COM voltage
Symbol Parameter Value Unit

VDRM/VRRM Repetitive peak off-state voltage 700 V

DPAK TC = 119 °C
On-state RMS current full cycle sine wave
IT(RMS) TO-220FPAB TC = 117 °C 2 A
50 to 60 Hz
TO-220AB TC = 119 °C

Non repetitive surge peak on-state current tP = 20 ms 20 A

ITSM
TJ initial = 25 °C, full cycle sine wave tP = 16.7 ms 21 A
I 2t Fusing capability tP = 10 ms 2.6 A 2s
Repetitive on-state current critical rate of
dI/dt Tj = 125 °C f = 120 Hz 50 A/µs
rise IG = 10 mA (tr < 100 ns)
VPP Non repetitive line peak pulse voltage(1) 2 kV
Tstg Storage temperature range - 40 to + 150 °C
TJ Operating junction temperature range - 30 to + 125 °C
TL Maximum lead soldering temperature during 10 s 260 °C
1. According to test described by IEC 61000-4-5 standard and Figure 17.

Table 2. Switch Gate characteristics (maximum values)

Symbol Parameter Value Unit

PG(AV) Average gate power dissipation 0.1 W

IGM Peak gate current (tP = 20 µs) 1 A
VGM Peak positive gate voltage (in respect to pin COM) 5 V

Table 3. Thermal resistances

Symbol Parameter Value Unit

S = 0.5 cm2(1) DPAK 70 °C/W

Rth (j-a) Junction to ambient TO-220FPAB 60 °C/W
TO-220AB 60 °C/W
DPAK 2.6 °C/W
Rth (j-c) Junction to case TO-220FPAB 3.5 °C/W
TO-220AB 2.6 °C/W
1. S = Copper surface under tab

2/17 DocID9469 Rev 4

ACS120 Characteristics

Table 4. Parameter description

Symbol Parameter description

IGT Triggering gate current

VGT Triggering gate voltage
VGD Non-triggering gate voltage
IH Holding current
IL Latching current
VTM Peak on-state voltage drop
VTO On state threshold voltage
Rd On state dynamic resistance
IDRM / IRRM Maximum forward or reverse leakage current
dV/dt Critical rate of rise of off-state voltage
(dV/dt)c Critical rate of rise of commutating off-state voltage
(dI/dt)c Critical rate of decrease of commutating on-state current
VCL Clamping voltage
ICL Clamping current

Table 5. Electrical characteristics

Symbol Test conditions Values Unit

IGT VOUT = 12V (DC), RL = 140 Ω QII -QIII TJ = 25°C Max 10 mA

VGT VOUT = 12V (DC), RL = 140 Ω QII -QIII TJ = 25 °C Max 1 V
VGD VOUT = VDRM, RL = 3.3 kΩ TJ = 125 °C Min 0.15 V
IH IOUT = 100 mA gate open TJ = 25 °C Max 45 mA
IL IG = 20 mA TJ = 25 °C Max 65 mA
VTM IOUT = 2.8 A, tp = 380 µs TJ = 25 °C Max 1.3 V
VTO TJ = 125 °C Max 0.85 V
Rd TJ = 125 °C Max 200 mΩ
TJ= 25 °C Max 2
IDRM /IRRM VOUT = 700 V µA
TJ = 125 °C Max 200
dV/dt VOUT = 460 V gate open TJ = 110 °C Min 500 V/µs
(dI/dt)c (dV/dt)c = 20 V/µs TJ = 125 °C Min 1 A/ms
VCL ICL = 1 mA, tp = 1 ms TJ = 25 °C Typ 1100 V

DocID9469 Rev 4 3/17

17
Characteristics ACS120

Figure 2. Maximum power dissipation versus Figure 3. On-state RMS current versus case
RMS on-state current temperature

3: ,7506$
 
  Į ƒ 72$%'3$.
 Į ƒ 
  72)3$%

 
 
 
 
 
 
ƒ
 Į 
 Į  7Fƒ&
,7506$
 
                

Figure 4. On-state RMS current versus ambient Figure 5. Relative variation of thermal
temperature impedance versus pulse duration

,7506$ . >=WK5WK@
 (
'3$. 72$%
 =WKMF
Į ƒ 72)3$%
 3ULQWHGFLUFXLWERDUG)5
QDWXUDOFRQYHFWLRQ '3$.
 6 FPð

 =WKMD

(
 72)3$%
72$%



7DPE ƒ& WSV
 (
      ( ( ( ( ( (

Figure 6. Relative variation of gate trigger, Figure 7. Relative variation of static dV/dt
holding and latching current versus junction versus junction temperature
temperature

,*7 ,+,/ >7M@,*7 ,+,/ >7M ƒ&@ G9GW>7M@G9GW>7M ƒ&@



  9287 9

 , 
*7
 

 

 

 ,/,+ 

 
7 ƒ& 7Mƒ&
M
 
                      

4/17 DocID9469 Rev 4

ACS120 Characteristics

Figure 8. Relative variation of critical rate of Figure 9. Relative variation of critical rate of
decrease of main current versus reapplied decrease of main current versus junction
dV/dt (typical values) temperature

GOGWF>G9GWF@VSHFLILHGGOGWF GOGWF>7M@GOGWF>7M ƒ&@
 
 
 
 
 
 
 
 
 
 7Mƒ&
 G9GWF9—V
 
               

Figure 10. Surge peak on-state current versus Figure 11. Non repetitive surge peak on-state
number of cycles current for a sinusoidal pulse with
width tp < 10 ms

,760$ ,760$
 
GOGWOLPLWDWLRQ $—V 7MLQLWLDO ƒ&
 1RQUHSHWLWLYHLQLWLDO7M ƒ&
 ,
W PV 760

2QHF\FOH
 


 5HSHWLWLYH7F ƒ&



72)3$%

1XPEHURIF\FOHV WSPV


   
   

Figure 12. On-state characteristics Figure 13. Thermal resistance junction to

(maximum values) ambient versus copper surface under tab

,70$ 5WKMDƒ&:

 
7MPD[ 3ULQWHGFLUFXLWERDUG)5 '3$.
9WR 9 
5G Pȍ
FRSSHUWKLFNQHVV —P





7M ƒ&


7M ƒ& 





970 9  6FPð
 
       
        

DocID9469 Rev 4 5/17

17
AC line switch basic application ACS120

2 AC line switch basic application

The ACS120 device is well adapted to washing machine, dishwasher, tumble drier,
refrigerator, air-conditioning systems, and cookware. It has been designed especially to
switch on and off low power loads such as solenoid, valve, relay, dispenser, micro-motor,
pump, fan and defrost heaters.
This AC switch is triggered by a negative gate current flowing out of the gate pin G. It can be
driven directly by the digital MCU through a resistor as shown on the typical application
diagram.
Thanks to its thermal and turn off commutation performance, the ACS120 switch can drive,
with no additional turn off snubber, an inductive load up to 2 A.

Figure 14. Typical application diagram

$&0DLQV
287

9VV
5J
*
.$6

9GG

&20

2.1 Protection against overvoltage: the best choice is ACS

In comparison with standard Triacs the ACS120 is over-voltage self-protected, as specified
by the new parameter VCL. This feature is useful in two operating conditions: in case of
turn off of very inductive load, and in case of surge voltage that can occur on the electrical
network.

6/17 DocID9469 Rev 4

ACS120 AC line switch basic application

2.2 High inductive load switch-off: turn-off overvoltage clamping

With high inductive and low RMS current loads the rate of decrease of the current is very
low. An overvoltage can occur when the gate current is removed and the OUT current is
lower than IH.
As shown in Figure 15 and Figure 16, at the end of the last conduction half-cycle, the load
current decreases (1). The load current reaches the holding current level IH (2), and the
ACS turns off (3). The water valve, as an inductive load (up to 15 H), reacts as a current
generator and an overvoltage is created, which is clamped by the ACS (4). The current
flows through the ACS avalanche and decreases linearly to zero. During this time, the
voltage across the switch is limited to the clamping voltage VCL. The energy stored in the
inductance of the load is dissipated in the clamping section that is designed for this purpose.
When the energy has been dissipated, the ACS voltage falls back to the mains voltage
value (230 V rms, 50 Hz) (5).

Figure 15. Turn-off operation of the ACS120 Figure 16. ACS120 switch static characteristic
switch with an electro-valve
,7


93($. 9 &/
, 287
P$GLY
 
 ,+
9287
 9GLY 
  97

,+ 9&/


—VGLY

Note: Same working principle described in item 2.2 is valid for both current directions.

DocID9469 Rev 4 7/17

17
AC line switch basic application ACS120

2.3 Alternating current mains transient voltage ruggedness

The ACS120 switch is able to withstand safely the AC mains transients either by clamping
the low energy spikes or by breaking-over when subjected to high energy shocks, even with
high turn-on current rises. The test circuit shown in Figure 17 is representative of the final
ACS120 application, and is also used to test the AC switch according to the IEC 61000-4-5
standard conditions. Thanks to the load limiting the current, the ACS120 switch withstands
the voltage spikes up to 2 kV above the peak mains voltage. The protection is based on an
overvoltage crowbar technology. Actually, the ACS120 breaks over safely as shown in
Figure 18. The ACS120 recovers its blocking voltage capability after the surge (switch-off
back at the next zero crossing of the current). Such non-repetitive tests can be done 10
times on each AC mains voltage polarity.

Figure 17. Overvoltage ruggedness test circuit for resistive and inductive loads

6XUJHJHQHUDWRU .9

5JHQHUDWRU

)LOWHULQJXQLW &F 0RGHORIWKHORDG

5 ȍ / —+
$&PDLQV 9UPV+]

287

*$7(

5J ȍ &20

Figure 18. Current and voltage of the ACS120 during IEC 61000-4-5 standard test with
R, L and VPP

97 9GLY

,7  $GLY

—V

8/17 DocID9469 Rev 4

ACS120 Package information

3 Package information

 Epoxy meets UL94-V0

 Lead-free package
 Recommended torque: 0.4 to 0.6 N·m (TO-220AB, TO-220FPAB)
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.

3.1 TO-220FPAB package information

Figure 19. TO-220FPAB package outline

DocID9469 Rev 4 9/17

17
Package information ACS120

Table 6. TO-220FPAB package mechanical data

Dimensions

Ref. Millimeters Inches(1)

Min. Max. Min. Max.

A 4.40 4.60 0.1732 0.1811

B 2.50 2.70 0.0984 0.1063
D 2.50 2.75 0.0984 0.1083
E 0.45 0.70 0.0177 0.0276
F 0.75 1.00 0.0295 0.0394
F1 1.15 1.70 0.0453 0.0669
F2 1.15 1.70 0.0453 0.0669
G 4.95 5.20 0.1949 0.2047
G1 2.40 2.70 0.0945 0.1063
H 10.00 10.40 0.3937 0.4094
L2 16.00 Typ. 0.6299 Typ.
L3 28.60 30.60 1.1260 1.2047
L4 9.80 10.60 0.3858 0.4173
L5 2.90 3.60 0.1142 0.1417
L6 15.90 16.40 0.6260 0.6457
L7 9.00 9.30 0.3543 0.3661
Dia. 3.00 3.20 0.1181 0.1260
1. Inches only for reference.

10/17 DocID9469 Rev 4

ACS120 Package information

3.2 DPAK package information

Figure 20. DPAK package outline

Note: This package drawing may slightly differ from the physical package. However, all the
specified dimensions are guaranteed.

DocID9469 Rev 4 11/17

17
Package information ACS120

Table 7. DPAK package mechanical data

Dimensions

Ref. Millimeters Inches(1)

Min. Typ. Max. Min. Typ. Max.

A 2.18 2.40 0.0858 0.0945

A1 0.9 1.10 0.0354 0.0433
A2 0.03 0.23 0.0012 0.0091
b 0.64 0.90 0.0252 0.0354
b4 4.95 5.46 0.1949 0.2150
c 0.46 0.61 0.0181 0.0236
c2 0.46 0.60 0.0181 0.0236
D 5.97 6.22 0.2350 0.2449
D1 4.95 5.60 0.1949 0.2205
E 6.35 6.73 0.2500 0.2650
E1 4.32 5.50 0.1701 0.2165
e 2.286 0.0900
e1 4.40 4.70 0.1732 0.1850
H 9.35 10.40 0.3681 0.4094
L 1.0 1.78 0.0394 0.0701
L2 1.27 0.0500
L4 0.6 1.02 0.0236 0.0402
V2 -8° +8° -8° +8°
1. Inches only for reference.

Figure 21. Footprint (dimensions in mm)

  

$



% 
7KHGHYLFHPXVWEHSRVLWLRQHGZLWKLQ  $ %

12/17 DocID9469 Rev 4

ACS120 Package information

3.3 TO-220AB package information

Figure 22. TO-220AB package outline

5HVLQJDWH
PPPD[
SURWXVLRQ

5HVLQJDWH
PPPD[
SURWXVLRQ

1. Resin gate position accepted in each of the two position as well as the symmetrical opposites.

DocID9469 Rev 4 13/17

17
Package information ACS120

Table 8. TO-220AB package mechanical data

Dimensions

Ref. Millimeters Inches(1)

Min. Max. Min. Max.

A 4.40 4.60 0.1732 0.1811

b 0.61 0.88 0.0240 0.0346
b1 1.14 1.70 0.0449 0.0669
c 0.48 0.70 0.0189 0.0276
D 15.25 15.75 0.6004 0.6201
D1 1.27 typ. 0.05 typ.
E 10.00 10.40 0.3937 0.4094
e 2.40 2.70 0.0945 0.1063
e1 4.95 5.15 0.1949 0.2028
F 1.23 1.32 0.0484 0.0520
H1 6.20 6.60 0.2441 0.2598
J1 2.40 2.72 0.0945 0.1071
L 13.00 14.00 0.5118 0.5512
L1 3.50 3.93 0.1378 0.1547
L20 16.40 typ. 0.6457 typ.
L30 28.90 typ. 1.1378 typ.
P 3.75 3.85 0.1476 0.1516
Q 2.65 2.95 0.1043 0.1161
1. Inches only for reference.

14/17 DocID9469 Rev 4

ACS120 Ordering information

4 Ordering information

Figure 23. Ordering information scheme

$&66%75

$&VZLWFK

1XPEHURIVZLWFKHV

1RPLQDOFRQGXFWLQJFXUUHQW,7506
 $
'LUHFWUHSHWLWLYHSHDNRIIVWDWHYROWDJH 9 '50
  9
*DWHVHQVLWLYLW\
6 P$
3DFNDJH
% '3$.
)3 72)3$%
7 72$%
3DFNLQJ
75 7DSHDQGUHHO
%ODQN 7XEH

Table 9. Ordering information

Order code Marking Package Weight Base Qty Packing mode

ACS120-7SB ACS1207S DPAK 0.32 g 75 Tube

ACS120-7SB-TR ACS1207S DPAK 0.32 g 2500 Tape and reel
ACS120-7SFP ACS1207S TO-220FPAB 1.9 g 50 Tube
ACS120-7ST ACS1207S TO-220AB 1.9 g 50 Tube

DocID9469 Rev 4 15/17

17
Revision history ACS120

5 Revision history

Table 10. Document revision history

Date Revision Changes

Apr-2004 1 Previous release.

28-Jan-2011 2 Added ECOPACK statement. Updated TC values in Table 1.
Updated DPAK package information and reformatted to current
28-May-2014 3
standard.
Added pin name on cover page package view and reformatted to
02-May-2016 4
current standard.

16/17 DocID9469 Rev 4

ACS120

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2016 STMicroelectronics – All rights reserved

DocID9469 Rev 4 17/17

17
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

STMicroelectronics:
ACS120-7SFP ACS120-7ST ACS120-7SB ACS120-7SB-TR ACS120-7SH