Scribd Logo
Upload

Welcome to Scribd!

  • 38 views

    How To Use Rt809f To Reprogram Ene Kbc90

    Uploaded by

    Hamza Abbasi Abbasi
    This document provides instructions for reprogramming an embedded controller to factory firmware using an RT809F serial ISP programmer. The steps include: 1. Connecting the SOIC pins of the RT809F programmer to the corresponding keyboard connector pins for communication. 2. Ensuring a 3V power source is available on the circuit board by plugging in the adapter or fixing the power supply. 3. Running the RT809F software, selecting the chip part number, reading and saving the original firmware, and writing the clean factory firmware to reprogram the embedded controller.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    How To Use Rt809f To Reprogram Ene Kbc90

    Uploaded by

    Hamza Abbasi Abbasi
    38 views27 pages
    This document provides instructions for reprogramming an embedded controller to factory firmware using an RT809F serial ISP programmer. The steps include: 1. Connecting the SOIC pins of the RT809F programmer to the corresponding keyboard connector pins for communication. 2. Ensuring a 3V power source is available on the circuit board by plugging in the adapter or fixing the power supply. 3. Running the RT809F software, selecting the chip part number, reading and saving the original firmware, and writing the clean factory firmware to reprogram the embedded controller.

    Original Description:

    THANKS

    Original Title

    How to Use Rt809f to Reprogram Ene Kbc90

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for reprogramming an embedded controller to factory firmware using an RT809F serial ISP programmer. The steps include: 1. Connecting the SOIC pins of the RT809F programmer to the corresponding keyboard connector pins for communication. 2. Ensuring a 3V power source is available on the circuit board by plugging in the adapter or fixing the power supply. 3. Running the RT809F software, selecting the chip part number, reading and saving the original firmware, and writing the clean factory firmware to reprogram the embedded controller.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    38 views27 pages

    How To Use Rt809f To Reprogram Ene Kbc90

    Uploaded by

    Hamza Abbasi Abbasi
    This document provides instructions for reprogramming an embedded controller to factory firmware using an RT809F serial ISP programmer. The steps include: 1. Connecting the SOIC pins of the RT809F programmer to the corresponding keyboard connector pins for communication. 2. Ensuring a 3V power source is available on the circuit board by plugging in the adapter or fixing the power supply. 3. Running the RT809F software, selecting the chip part number, reading and saving the original firmware, and writing the clean factory firmware to reprogram the embedded controller.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 27

    HOW TO USE RT809F

    TO REPROGRAM ENE KBC9012QF


    TO FACTORY FIRMWARE
    PRESENT TO YOU

    By Adie Dkhaz
    WARNING
    FOR TECHNICIAN ONLY
    ANY FAILUR OR INCORRECT
    PROCEDURE WILL HARMFULL YOUR
    COMPUTER
    RT809F SERIAL ISP PROGRAMMER
    PIN INSTALATION
    JUMPER POIN
    CONNECT SOIC PIN TO KEYBOARD
    CONNECTOR
    PIN1 TO KSI4
    PIN 2 TO KSI7
    PIN 4 TO GND AND KSO3
    PIN 5 TO KSI6
    PIN 6 TO KSI 5
    PIN 8 TO ANY 3V POWER ON CIRCUIT
    TO GET 3V POWER ON CIRCUIT

    WE SHOULD PLUG IN THE ADAPTER


    IF CIRCUIT MISSING 3V POWER FIXED THE
    SMPS POWER SUPPLY BEFORE
    REPROGRAMM EMBEDDED CONTROLER
    INSTALATION WILL LOOK LIKE THIS
    RUN RT809F EXE AND INPUT CHIP
    PART NUMBER CLICK HISTORY AND
    SELECT KB9012QF A3 AND CLICK OK
    CLICK READ AND SAVE TO BACKUP OLD
    DUMP ORIGINAL FIRMWARE
    OPEN CLEAN FACTORY 128 KB
    FIRMWARE AND CLICK WRITE TO
    REPROGRAMM
    WAIT UNTIL VERIFYING DONE AND
    NEW CLEAN FIRMWARE INSTALED
    end

    You might also like