Penguard Tie Coat

Technical Data Sheet
15521;15522
epoxy
15521
VValidationDate).
Penguard Tie Coat

Product description
This is a two component polyamide cured epoxy coating. Specially designed as a tie coat/sealer on top of
inorganic zinc silicate primers, galvanised steel and thermally sprayed zinc. To be used as primer in a complete
system in atmospheric environments.
Typical use
Suitable for structural steel and piping to be exposed to corrosive environments up to very high. Recommended
for offshore environments, refineries, power plants, bridges, buildings and mining equipment.
Other
Colours
red
Product data
Property
Test/Standard
Solids by volume
Gloss level (60 )
Flash point
VOC-Solvent Emission Directive
Description
ISO 3233
ISO 2813
50 2 %
matt (0-35)
ISO 3679 Method 1

SED (1999/13/EC)
25 C
316 g/kg
The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss level: According to Jotun Performance Coatings' definition.
Recommended film thickness per coat

Film thickness and
spreading rate
Dry film thickness

(m)
(m)
Theoretical
spreading rate
(m/l)
Minimum
50
100
10
Maximum
Typical
100
75
200
150
5
6,7
Wet film thickness
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Date of issue:
1 August 2014
by Jotun Group
Page: 1/4
This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Penguard Tie Coat
Surface preparation summary table

Surface preparation
Substrate
Minimum
Recommended
Galvanised steel
The surface shall be clean, dry and

appear with a rough and dull profile.
Light brush blasting using nonmetallic abrasive leaving a clean,

rough and even pattern.
Coated surfaces
Clean, dry and undamaged

compatible coating (ISO 12944-4 6.
1)
Clean, dry and undamaged

compatible coating (ISO 12944-4 6.
1)
Application
Application methods
The product can be applied by
Spray:
Use airless spray or conventional spray.
Brush:
Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Product mixing ratio (by volume)

Penguard Tie Coat Comp A
Penguard Tie Coat Comp B
3
1
part(s)
part(s)
Thinner/Cleaning solvent
Thinner:
Jotun Thinner No. 17
Guiding data for airless spray

Nozzle tip (inch/1000):
15-19
Pressure at nozzle (minimum):
150 bar/2100 psi
Drying and Curing time

Substrate temperature
5 C
10 C
23 C
40 C
Surface (touch) dry

Dried to handle
Dried to over coat, minimum
Dried/cured for service
7h
24 h
24 h
18 d
4h
18 h
18 h
14 d
2h
12 h
12 h
7d
30 min
7h
7h
3d
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and
within the DFT range of the product.
Date of issue:
1 August 2014
by Jotun Group
Page: 2/4


Penguard Tie Coat
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface.
Dried to handle: Minimum time before the coated objects can be handled without physical damage.
Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Heat resistance
Temperature
Continuous
Dry, atmospheric
90 C
Peak
120 C
Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat:
zinc silicate
Subsequent coat:
acrylic, epoxy, polyurethane
Packaging (typical)
Volume
(litres)
Size of containers
(litres)
11.25
3.75
18
4
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Shelf life at 23 C
Date of issue:
1 August 2014
24 month(s)
12 month(s)
by Jotun Group
Page: 3/4


Penguard Tie Coat
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
Products primarily meant for use as primers and antifoulings may have slight color variations from batch to
batch. Such products may fade and chalk when exposed to sunlight and weathering.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue:
1 August 2014
by Jotun Group
Page: 4/4


Penguard Tie Coat

Uploaded by

Copyright:

Available Formats

Penguard Tie Coat

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Penguard Tie Coat

Uploaded by

Copyright:

Available Formats

Technical Data Sheet