FiddleII50 Service Manual

SERVICE MANUAL
Fiddle II 50
SYM
FORWARD
This service manual contains the technical data of each component

inspection and repair for the SYM series motorcycle. The manual is shown
with illustrations and focused on Service Procedures, Operation Key
Points, and Inspection Adjustment so that provides technician with service
guidelines.
If the style and construction of the motorcycle are different from that of the
photos, pictures shown in this manual, the actual vehicle shall prevail.
Specifications are subject to change without notice.
This manual that contains all data, illustration, indication and specifications
is based on current production information. SYM reserves the right to make
changes at any time without notice and without incurring any obligation
whatever. No part of this manual can be duplicated by any means without
written permission of SANYANG.
SERVICE DEPARTMENT
SAN YANG INDUSTRY CO., LTD.
HOW TO USE THIS MANUAL
SYM
This service manual describes basic information of different system parts and
system inspection & service for SYM series motorcycles. In addition, please
refer to the manual contents in detailed for the model you serviced in
inspection and adjustment.
The first chapter covers general information and trouble diagnosis.
The second chapter covers service maintenance.
The third to the eleventh chapters cover engine and driving systems.
The twelfth to fifteenth chapters are contained the parts set of assembly
body.
The sixteenth chapter is electrical equipment.
The seventh chapter is for wiring diagram.
Please see index of content for quick having the special parts and system
information.
SYM
CONTENTS
CONTENTS
GENERAL INFORMATION/TROUBLE DIAGNOSIS ...................................1

MAINTENANCE INFORMATION .................................................................2
LUBRICATION SYSTEM..............................................................................3
FUEL SYSTEM .............................................................................................4
ENGINE REMOVAL......................................................................................5
CYLINDER HEAD/VALVE............................................................................6
CYLINDER/PISTON......................................................................................7
"V" TYPE BELT DRIVING SYSTEM/KICK STARTER ARM/ STARTER CLUTCH .......8
FINAL DRIVING MECHANISM.....................................................................9

A.C. GENERATOR/STARTING CLUTCH ....................................................10
CRANKCASE/CRANKSHAFT .....................................................................11
BODY COVER ..............................................................................................12
BRAKE SYSTEM..........................................................................................13
STEERING/FRONT WHEEL/FRONT SHOCK ABSORBER ........................14
REAR WHEEL/SUSPENSION......................................................................15
ELECTRICAL EQUIPMENT .........................................................................16
ELECTRICAL DIAGRAM .............................................................................17
MECHANISM ILLUSTRATIONS
SYM
Meter
High & Low beam/Passing/turn

signal/horn
Start magnetic switch
Fuel tank / Fuel unit
Head light/
Position light
Rear brake lever
Frame number
Horn/REG.REC
Tail light
Front turn
signal light
RR. turning
signal light
Air cleaner
Gear oil filling
bolt
Gear oil draining
bolt
Front disk brake
Engine number/engine
oil draining bolt
Light/starter switch
Engine control
switch
Front brake lever

Battery/Fuse/CDI
Ignition switch
Winker relay
Tail light
Front turn
signal light
Rear turn
signal light
Exhaust muffler
Ignition coil
Oil level
A.C. Generator
SPECIAL TOOL
SYM
ITEM: OUTER BEARING PULLER
ITEM: ACG FLYWHEEL PULLER
NOSYM-6204010
PURPOSE: REMOVE THE BEARING
NOSYM-3110A00
PURPOSE: REMOVE ACG FLYWHEEL
ITEM: LOCK NUT PULLER
ITEM: UNIVERSAL HOLDER
NOSYM-9020100
PURPOSE: REMOVE THE LOCK NUT
NOSYM-2210100
PURPOSE:HOLD THE MDF/CLUTCH OUTER
ITEM: CLUTCHSPRING COMPRESSOR
ITEM: CLUTCH NUT WRENCH
NOSYM-2301000
PURPOSE:DISASSEMBLE THE CLUTCH
NOSYM-9020200
PURPOSE:LOOSE THE CLUTCH NUT
SYM
SPECIAL TOOL
ITEM: GY6 STARTER GEAR PULLER
NOSYM-2822100-GY6
PURPOSE:REMOVE THE STARTER GEAR
SYM
1. GENERAL INFORMATION/TROUBLE DIAGNOSIS
SYMBOLS AND MARKS ....................1-1

GENERAL SAFETY............................1-2
SERVICE PRECAUTIONS .................1-3
SPECIFICATIONS..............................1-9
TORQUE VALUES (ENGINE) .............. 1-10

TORQUE VALUES (FRAME) ............... 1-11
TROUBLES DIAGNOSIS ..................... 1-12
LUBRICATION POINTS ....................... 1-16
SYMBOLS AND MARKS

Symbols and marks are used in this manual to indicate what and where the special service are
needed, in case supplemental information is procedures needed for these symbols and marks,
explanations will be added to the text instead of using the symbols or marks.
Warning
Means that serious injury or even death may result if procedures are not
followed.
Caution
Means that equipment damages may result if procedures are not followed.
Engine oil
Grease
Locking sealant
Oil seal
Renew
Limits to use SAE 10W-30 API SH/CD class oil. Warranty will not cover the
damage that caused by not apply with the limited engine oil.
King Mate G-3 is recommended.
Apply sealant, medium strength sealant should be used unless otherwise
specified.
Apply with lubricant.
Replace with a new part before installation.
Brake fluid Use recommended brake fluid DOT3 or WELLRUN brake fluid.
Special tools
Special service tools.
Correct
Meaning correct installation.
Wrong
Meaning wrong installation.
Indication Indication of components.

Directions
Indicates position and operation directions.

Components assembly directions each other.
Indicates where the bolt installation direction, --- means that bolt cross
through the component (invisibility).
1-1
SYM
GENERAL SAFETY
Carbon monoxide
If you must run your engine, ensure the place is
well ventilated. Never run your engine in a
closed area. Run your engine in an open area, if
you have to run your engine in a closed area, be
sure to use an extractor.
Caution
Exhaust contains toxic gas which may cause
one to lose consciousness and even result in
death.
Gasoline
Gasoline is a low ignition point and explosive
material. Work in a well-ventilated place, no
flame or spark should be allowed in the work
place or where gasoline is being stored.
Caution
Gasoline is highly flammable, and may explode
under some conditions, keep it away from
children.
Battery
Caution
Battery emits explosive gases; flame is
strictly prohibited. Keep the place well
ventilated when charging the battery.
Battery contains sulfuric acid (electrolyte)
which can cause serious burns so be careful
do not be spray on your eyes or skin. If you
get battery acid on your skin, flush it off
immediately with water. If you get battery
acid in your eyes, flush it off immediately
with water, then go to hospital to see an
ophthalmologist.
If you swallow it by mistake, drink a lot of
water or milk, and take some laxative such
as castor oil or vegetable oil, and then go to
see a doctor.
Keep electrolyte beyond reach of children.
Brake shoe
Used engine oil
Caution
Prolonged contact with used engine oil (or
transmission oil) may cause skin cancer
although it might not be verdict.
Do not use an compressed air or a dry brush to

clean components of the brake system, use a
vacuum cleaner or the equivalent to avoid
asbestos dust flying.
Caution
Inhaling asbestos dust may cause disorders
and cancer of the breathing system.
Hot components
Caution
Components of the engine and exhaust system
can become extremely hot after engine running.
They remain very hot even after the engine has
been stopped for some time. When performing
service work on these parts, wear insulated
gloves and wait until cooling off.
1-2
Brake fluid
Caution
Spilling brake fluid on painted, plastic, or rubber
parts may cause damage to the parts. Place a
clean towel on the above-mentioned parts for
protection when servicing the brake system.
Keep brake fluid beyond reach of children.
SYM
SERVICE PRECAUTIONS
Always use with SANYANG genuine parts
and recommended oils. Using non-designed
parts for SANYANG motorcycle may damage
the motorcycle.
Special tools are designed for remove and

install of components without damaging the
parts being worked on. Using wrong tools
may result in parts damaged.
When servicing this motorcycle, use only

metric tools. Metric bolts, nuts, and screws
are not interchangeable with the English
system, using wrong tools and fasteners may
damage this vehicle.
Clean the outside of the parts or the cover
before removing it from the motorcycle.
Otherwise, dirt and deposit accumulated on
the part's surface may fall into the engine,
chassis, or brake system to cause a damage.
Wash and clean parts with high ignition point
solvent, and blow dry with compressed air.
Pay special attention to O-rings or oil seals
because most cleaning agents have an
adverse effect on them.
Never bend or twist a control cable to prevent

stiff control and premature worn out.
Rubber parts may become deteriorated when

old, and prone to be damaged by solvent and
oil. Check these parts before installation to
make sure that they are in good condition,
replace if necessary.
When loosening a component which has
different sized fasteners, operate with a
diagonal pattern and work from inside out.
Loosen the small fasteners first. If the bigger
ones are loosen first, small fasteners may
receive too much stress.
Store complex components such as
transmission parts in the proper assemble
order and tie them together with a wire for
ease of installation later.
Note the reassemble position of the important

components before disassembling them to
ensure they will be reassembled in correct
dimensions (depth, distance or position).
Components not to be reused should be
replaced when disassembled including
gaskets metal seal rings, O-rings, oil seals,
snap rings, and split pins.
1-3

The length of bolts and screws for
assemblies, cover plates or boxes is different
from one another, be sure they are correctly
installed. In case of confusion, Insert the bolt
into the hole to compare its length with other
bolts, if its length out side the hole is the
same with other bolts, it is a correct bolt.
Bolts for the same assembly should have the
same length.
SYM
Remove residues of the old gasket or sealant

before reinstallation, grind with a grindstone if
the contact surface has any damage.
The ends of rubber hoses (for fuel, vacuum,

or coolant) should be pushed as far as they
can go to their connections so that there is
enough room below the enlarged ends for
tightening the clamps.
Groove
Tighten assemblies with different dimension

fasteners as follows:
Tighten all the fasteners with fingers, then
tighten the big ones with special tool first
diagonally from inside toward outside,
important components should be tightened 2
to 3 times with appropriate increments to
avoid warp unless otherwise indicated. Bolts
and fasteners should be kept clean and dry.
Do not apply oil to the threads.
Clamp
Connector
Rubber and plastic boots should be properly

reinstalled to the original correct positions as
designed.
Boots
When oil seal is installed, fill the groove with

grease, install the oil seal with the name of
the manufacturer facing outside, check the
shaft on which the oil seal is to be installed
for smoothness and for burrs that may
damage the oil seal.
The tool should be pressed against two (inner

and outer) bearing races when removing a
ball bearing. Damage may result if the tool is
pressed against only one race (either inner
race or outer race). In this case, the bearing
should be replaced. To avoid damaging the
bearing, use equal force on both races.
Manufacturer's
name
Both of these examples can result in bearing damage.
1-4
SYM
Lubricate the rotation face with specified

lubricant on the lubrication points before
assembling.
Before battery removal operation, it has to

remove the battery negative (-) cable firstly.
Notre tools like open-end wrench do not
contact with body to prevent from circuit short
and create spark.
Check if positions and operation for installed

parts is in correct and properly.
After service completed, make sure all
connection points is secured. Battery
positive (+) cable should be connected firstly.
And the two posts of battery have to be
greased after connected the cables.
Make sure service safety each other when

conducting by two persons.
Make sure that the battery post caps are
located in properly after the battery posts had
been serviced.
Note that do not let parts fall down
If fuse burned, it has to find out the cause

and solved it. And then replace with
specified capacity fuse.
capacity
verification
1-5

When separating a connector, it locker has to
be unlocked firstly. Then, conduct the
service operation.
SYM
Before terminal connection, check if the boot

is crack or the terminal is loose.
Insert the terminal completely. Check if the

terminal is covered by the boot. Do not let
boot open facing up.
Do not pull the wires as removing a
connector or wires. Hold the connector
body.
Make sure if the connector pins are bent,

extruded or loosen.
Secure wires and wire harnesses to the

frame with respective wire bands at the
designated locations. Tighten the bands so
that only the insulated surfaces contact the
wires or wire harnesses.
Insert the connector completely. If there are

two lockers on two connector sides, make
sure the lockers are locked in properly.
Check if any wire loose.
Wire band and wire harness have to be

clamped secured properly.
Check if the connector is covered by the twin

connector boot completely and secured
properly.
Do not squeeze wires against the weld or its

clamp.
1-6
SYM
Do not let the wire harness contact with

rotating, moving or vibrating components as
routing the harness.
Keep wire harnesses far away from the hot

parts.
Protect wires or wire harnesses with electrical

tape or tube if they contact a sharp edge or
corner. Thoroughly clean the surface where
tape is to be applied.
Secure the rubber boot firmly as applying it

on wire harness.
Do not touch it.
Route wire harness to avoid sharp edges or

corners and also avoid the projected ends of
bolts and screws.
Never use wires or harnesses which

insulation has been broken. Wrap electrical
tape around the damaged parts or replace
them.
Route harnesses so that they neither pull too

tight nor have excessive slack.
Never clamp or squeeze the wire harness as
installing other components.
Please do not clip or
squeeze the wire.
Do not extend
it too much.
1-7

Do not let the wire harness been twisted as
installation.
With sand paper to clean rust on connector

pins/terminals if found. And then conduct
connection operation later.
Clean rust.
Wire harnesses routed along the handlebar

should not be pulled too tight or have
excessive slack, be rubbed against or
interfere with adjacent or surrounding parts in
all steering positions.
Before operating a test instrument, operator

should read the operation manual of the
instrument. And then, conduct test in
accordance with the instruction.
Do you know how to set the

instrument to its measurement
position and the insert locations
of its two probes?
1-8
SYM
SYM
SPECIFICATIONS
1325mm
Front
40kg
Rear
59kg
Total
99kg
Passengers/
Weight
Two men/110 kg
Front
84kg
Rear
125kg
Total
209kg
Type
4-STROKE ENGINE
Installation and
arrangement
Fuel Used
Vertical, below center,

incline 80
Unleaded gasoline
4-stroke/forced air
cooled
Cylinder
Suspen
sion
System
Wheel Base
Rear
unit swing
Tire
Specifi
cations
1140 mm
Telescopic fork
Front
110/70-12(47J)
Rear
120/70-12(51J)
Brake
System
Overall Height
AKA(AW05W-6)
Front
Front
DISK ( 190 mm)
Rear
DRUM ( 110 mm)
Performa
nce
698 mm
MODEL
Deceleration
equipment
Overall Width
Curb Weight
1870mm
Cycle/Cooling
Max. Speed
<45km/h
Climb Ability
26 Below
Primary Reduction
BELT
Final Reduction
GEAR
Clutch
Auto centrifugal clutch
Transmission
C.V.T.
Speedometer
0 ~ 80 km/hr
Horn
75~112dB(A)
Bore
39.0 mm
Muffler
Expansion & Pulse Type
Stroke
41.35 mm
Exhaust Pipe Position

and Direction
Number/Arran
gement
Single Cylinder/
horizontal
Lubrication System
Right side, and

Backward
Forced-circulation&
splashing
Displacement
49.4 cc
Compression
Ratio
11.8:1
Max. HP
2.35KW/8500 rpm
Max. Torque
2.91N.m /6500 rpm
Air Filtration
Paper filter
Ignition
C.D.I.
< 71dB
Starting System
Kick & electrical starter
Noise Emission
Engine Weight(dry
weight)
Exhaust
Emission
ENGINE
SANYANG
Overall Length
Total Weight
WEIGHT
DIMENSION
MAKER
CO
<12.0 g/km
HC
<1.0 g/km
NOx
<1.2 g/km
23kg
1-9
SYM
TORQUE VALUES (ENGINE)

ITEM
Q'TY
THREAD DIA
TORQUE
(mm)
VALUE(Kg-m)
REMARKS
Cylinder head bolts
0.8~1.2
Cylinder head nuts
1.8~2.2
Apply oil to thread
Cylinder/cylinder head two-ends bolts
0.7~1.1
Tighten to crankcase
Cam holder nut
1.0~1.4
Right crank case cover bolts
10
0.8~1.2
Pulse generator bolts
0.35~0.5
Valve adjustment fixing nuts
0.7~1.1
Spark plug
10
1.0~1.4
Engine oil strainer cap
30
1.0~2.0
Gear oil draining plug
1.0~1.5
Gear oil filling bolt
1.0~1.5
Oil pump bolts
0.8~1.2
Oil pump drive sprocket nuts
0.8~1.2
Left crankcase cover bolts
10
0.8~1.2
Cylinder head cover bolts
0.8~1.2
Camshaft chain tensioner pivot
0.8~1.2
Camshaft chain adjuster bolts
1.0~1.4
Cooling fan bolts
0.8~1.2
Shroud A/B
0.8~1.2
RR. brake fixing nut
1.5~2.0
Flywheel nut
10
3.5~4.5
Transmission(Gear box) bolts
2.6~3.0
RR. brake arm bolt
0.7~1.1
Drive face nut
12
5.0~6.0
Drive pulley nut
10
3.5~4.5
A.C. generator flange bolt
0.8~1.2
Air/C connect bracket bolts
0.8~1.2
Start motor bolts
0.8~1.2
Brake arm bolt
0.7~1.1
Kick starter arm bolt
0.8~1.2
Carburetor nut
0.8~1.2
A.I. fixing hex cap nut
0.8~1.2
Crankcase bolts
0.8~1.2
Exhaust pipe bolts
3.0~3.6
Exhaust pipe connecting nuts
1.0~1.4
1-10
Apply oil to thread
Hex socket bolt
SYM
TORQUE VALUES (FRAME)

Q'TY
THREAD DIA
(mm)
TORQUE
VALUE(Kg-m)
Mounting bolt for steering

handlebar
10
4.0~5.0
Mounting nut for steering rod
25.4
1.0~2.0
Cone seat for steering rod
25.4
0.2~0.3
Front wheel shaft nut
12
5.0~7.0
Rear wheel shaft nut
16
11.0~13.0
Wheel hub/rim mounting nuts
2.8~3.2
Speedometer cable locking screw
0.15~0.3
2.4~3.0
10
3.5~4.5
2.4~3.0
Brake lever bolts
0.8~1.2
Front brake hose bolts
10
3.3~3.7
Front brake air-bleeding valve
0.8~1.0
Front brake disc mounting bolts
10
4.0~4.5
Front brake clipper mounting bolts
10
3.1~3.5
Drum brake arm bolts (front/rear)
0.8~1.2
Engine suspension bracket bolts
10
4.5~5.5
On frame side
Engine connection bolt
10
4.5~5.5
On engine side
Main standard nut
10
3.5~4.5
Foot-starting lever bolt
1.6~1.8
Air cleaner bolts
1.0~1.4
ITEM
Front shock absorber mounting

bolts
Rear shock absorber upper
connection bolt
Rear shock absorber upper
connection bolt
REMARKS
The torque values listed in above table are for more important tighten torque values. Please see
standard values for not listed in the table.
Standard Torque Values for Reference
TYPE
TIGHTEN TORQUE
TYPE
TIGHTEN TORQUE
5mm boltnut
6mm boltnut
8mm boltnut
10mm boltnut
12mm boltnut
0.45~0.60kgf-m
3mm screw
4mm screw
5mm screw
6mm screwSH nut
6mm boltnut
0.05~0.08kgf-m
0.10~0.15kgf-m
0.35~0.50kgf-m
0.70~1.10kgf-m
1.00~1.40kgf-m
8mm boltnut
2.40~3.00kgf-m
10mm boltnut
3.50~4.50kgf-m
0.80~1.20kgf-m
1.80~2.50kgf-m
3.00~4.00kgf-m
5.00~6.00kgf-m
1-11
SYM
TROUBLES DIAGNOSIS
A. Engine hard to start or can not be started
Check and adjustment
Fault condition
Loosen carburetor drain

bolt to check if there is
gasoline inside the
carburetor
Fuel supplied tom

carburetor sufficient
No fuel is supplied to
carburetor
Remove spark plug, install

it into spark plug cap, and
perform a spark test
against engine ground.
Check if sparks
1. No fuel in fuel tank

2. Check if the pipes, fuel tank to
carburetor and intake vacuum,
are clogged.
3. Float valve clogged
4. Lines in fuel tank evaporation
system clogged
5. Malfunction of fuel pump
6. Loosen or damaged fuel pump
vacuum hose
7. Fuel filter clogged
Weak sparks, no spark

at all
1. Malfunction of spark plug

2. Spark plug foul
3. Malfunction of CDI set
4. Malfunction of AC generator
5. Ignition coil is in open or short
circuit
6. Ignition coil leads open or short
circuit
7. Malfunction of main switch
Low compression
pressure or no pressure
1. Piston ring seized

2. Malfunction of cylinder valves
3. Worn cylinder and piston ring
4. Cylinder gasket leak
5. Sand hole in compression parts
There are some signs of

ignition, nut engine can
not be started
1. Malfunction of throttle valve

operation
2. Air sucked into intake manifold
3. Incorrect ignition timing
perform cylinder
compression pressure test.
cylinder compression
pressure normal
Probable causes
Re-start by following the

starting procedures
No ignition
Remove the spark plug

again and check it.
Dry spark plug
Wet spark plug
Remove carburetor after 30 minutes

and connect a hose onto fuel rich
circuit. Then blow the hose with air
Blowing in normal
1-12
Blowing clogged
1. Fuel level in carburetor too high

2. Malfunction of throttle valve
operation
3. Throttle valve opening too wide
1. Malfunction of automatic bystarter
SYM
B. Engine run sluggish (Speed does not pick up, lack of power)
Fault condition
Probable causes
Try gradual acceleration

and check engine speed
Engine speed can be

increased.
Engine speed can not be

increased.
Check ignition timing

(Using ignition lamp)
Ignition timing correct
Incorrect ignition timing
Check cylinder compression

pressure (using compression
pressure gauge)
Compression pressure correct
No compression
1. Air cleaner clogged

2. Poor fuel supply
3. Lines in fuel tank evaporation
system clogged
4. Exhaust pipe clogged
5. Fuel level too low in carburetor
6. Fuel nozzle clogged in
carburetor
1. Malfunction of CDI
2. Malfunction of AC alternator
1. Cylinder & piston ring worn out

2. Cylinder gasket leaked
3. Sand hole in compression parts
4. Valve deterioration
5. Seized piston ring
Check if carburetor jet is

clogged
No clogged
Clogged
1. Remove foreign
Remove spark plug
No foul or discoloration
Fouled and discoloration
Check if engine over heat
Normal
Engine overheat
Continually drive in
acceleration or high speed
No knock
Knock
1. Remove dirt
2. Incorrect spark plug heat range
1. Piston and cylinder worn out

2. Lean mixture
3. Poor fuel quality
4. Too much carbon deposited in
combustion chamber
5. Ignition timing too advanced
6. Poor circuit on the cooling
system
1. Too much carbon deposited in
combustion chamber
2. Lean mixture
3. Poor fuel quality
4. Ignition timing too advanced
1-13
SYM
C. Engine runs sluggish (especially in low speed and idling)

Fault condition
Probable causes

(using ignition lamp)
Normal
Abnormal
1. Incorrect ignition timing (malfunction

of CDI or AC alternator)
Poor
1. Rich mixture (loosen the screw)

2. Lean mixture (tighten the screw)
Adjust the air screw of

carburetor
Good
Air sucked through

carburetor gasket
No air sucked
Air sucked
Remove spark plug, install

spark plug into spark plug
cap and perform spark test
against engine ground
Good spark
Poor
D. Engine runs sluggish (High speed)

Fault condition
1. Poor heat insulation gasket

2. Carburetor lock loose
3. Poor intake gasket
4. Poor carburetor O-ring
5. Vacuum hose crack
1. Spark plug fouled

3. Malfunction of AC generator
4. Malfunction of ignition coil
5. Open or short circuit in spark plug
leads
6. Malfunction of main switch
Probable causes

Normal
Abnormal
2. Malfunction of AC alternator
Check for fuel supplying

system in automatic fuel cup
Good
Poor
1. Insufficient fuel in fuel tank

2. Fuel filter clogged
3. Restricted fuel tank vent
Check if carburetor clogged
No clogged
1-14
Clogged
1. Cleaning
SYM
E. CLUTCH, DRIVING AND DRIVING PULLEY

FAULT CONDITIONS
Engine can be started but

motorcycle can not be moved.
Engine running and misfire as

motorcycle initial forward moving
or jumping suddenly (rear wheel
rotating as engine in running)
Poor initial driving ( Poor

climbing performance)
PROBABLE CAUSES
1.
2.
3.
4.
5.
6.
Driving belt worn out or deformation

Driving disk damaged
Driving pulley spring broken
Clutch ling broken
Driving slide-shaft gear groove broken
Transmission gear damaged
1. Clutch ling spring broken

2. Clutch outer stick with clutch balance weights
3. Connection parts in clutch and shaft worn out
or burned
1. Driving belt worn out or deformation

2. Balance weight roller worn out
3. Driving sliding gear shaft worn out
4. Driving disk spring deformation
5. Driving sliding gear shaft worn out
6. Greased in driving belt and sliding gear.
1-15
SYM

LUBRICATION POINTS
Acceleration cable/ Front & rear brake lever pivot
Steering shaft bearing
Speedometer gear /
Front wheel bearing
1-16
Side stand shaft
Main stand shaft
Rear wheel bearing
SYM
2. MAINTENANCE INFORMATION
PRECAUTIONS IN OPERATION .......2-1

PERIODICAL MAINTENANCE
SCHEDULE ........................................2-2
LUBRICATION SYSTEM ....................2-3
FUEL SYSTEM...................................2-4
AIR CLEANER....................................2-5
THROTTLE VALVE OPERATION ......2-5
VALVE CLEARANCE INSPECTION
& ADJUSTMENT ................................2-6
CARBURETOR IDLING SPEED
ADJUSTMENT ..................................2-7
IGNITION SYSTEM/SPARK PLUG .. 2-8

CYLINDER COMPRESSION PRESSURE . 2-9
DRIVING SYSTEM............................. 2-9
STEERING SYSTEM ......................... 2-10
SUSPENSION SYSTEM .................... 2-10
FRONT DISK BRAKE SYSTEM ......... 2-11
DRUM BRAKE SYSTEM .................... 2-13
WHEEL/TIRE...................................... 2-14
BATTERY ........................................... 2-15
HEADLIGHT ADJUSTMENT .............. 2-15
NUTSBOLTS TIGHTEN.................. 2-15
PRECAUTIONS IN OPERATION
Specification
Fuel Tank Capacity
Engine Oil
Transmission Gear oil
Main
5000 c.c.
auxiliary
1500 c.c.
capacity
800 c.c.
change
750 c.c.
capacity
110 c.c.
change
100 c.c.
Clearance of throttle valve
2~6 mm
Spark plug
TORCH A7RC Gap: 0.6~0.7 mm
F Mark in idling speed
Before TDC 13 / 2200 rpm
Full timing advanced
Idling speed
2100100 rpm
Cylinder compression pressure
11.80.4:1 kg/cm
Valve clearance: IN/EX
0.060.02 mm
Tire dimension
Tire pressure (cold)
front / rear
110/70-12(47J) /120/70-12(51J)
single
Front: 1.75 kg/cm
rear: 2.00 kg/cm
Two persons
Front: 1.75 kg/cm
rear: 2.25 kg/cm
Battery Capacity
YTX7A-BS 12V6Ah (MF battery)
Play of drum brake lever
10~20 mm
2-1
SYM
PERIODICAL MAINTENANCE SCHEDULE

Mainte
nance
Code
Item
Initial 300KM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
Air cleaner
2nd air jet leaner
Fuel filter
Oil filter
Engine oil change
Tire pressure
Battery inspection
Brake & free play check
Steering handle check
Cushion operation check
Every screw tightening check
Gear oil check for leaking
Spark plug check or change
Gear oil change
Frame lubrication
Exhaust pipe
Ignition timing
Emission check in Idling
Throttle operation
Engine bolt tightening
CVT driving device (belt
CVT driving device (roller)
Lights/electrical equipment/mutli-meters
Main/side stands & springs
Fuel pipes
Cam chain
Valve clearance
Crankcase vapor control System
Crankcase blow-by over-flow pipe
2nd air jet system
vapor control system
I
I
I
C
R
I
I
I
I
I
I
I
I
R
Code: I ~ Inspection, cleaning, and adjustment
I
I
A
I
I
1 Month
3 month
6 month
Every1000KM Every3000KM Every6000KM

C
C
C
I
C
1 year
Every12000K
M
R
R
R
I
I
I
I
I
I
I
I
I
R
Replacement for every 5000km(5 months)
L
I
I
I
I
I
I
C
I
I
I
I
I
I
I
I
R ~ Replacement
I
I
I
I
A
C
Replacement for every 2000km
I
C
I
C ~ Cleaning (replaced if necessary)
L ~ Lubrication
Have your motorcycle checked, adjusted, and recorded maintenance data periodically by your SYM Authorized Dealer to
maintain the motorcycle at the optimum condition
The above maintenance schedule is established by taking the monthly 1000 kilometers as a reference which ever comes
first.
Remarks:
1. These marks in the schedule are emission control items. According to EPA regulations, these items
must be perform normally periodical maintenance following the use r manual instructions. They are
prohibited to be adjusted or repaired by unauthorized people. Otherwise, SYM is no responsible for the
charge.
2. Clean or replace the air cleaner element more often when the motorcycle is operated on dusty roads or in the
Heavily- polluted environment.
3. Maintenance should be performed more often if the motorcycle is frequently operated in high speed and after the
motorcycle has accumulated a higher mileage.
4. Preventive maintenance
a. Ignition system - Perform maintenance and check when continuous abnormal ignition, misfire, after-burn,
overheating occur.
b. Carbon deposit removal - Remove carbon deposits in cylinder head, piston heads, exhaust system when power is
obvious lower than ever.
c. Replace worn out pistons, cylinder head.
2-2
SYM
LUBRICATION SYSTEM
Engine Oil Capacity
Caution
The vehicle must be parked on a level
ground when checking oil capacity.
Run the engine for 2-3 minutes then stop,
wait about 2-3 more minutes allowing
engine oil to settle before checking the oil
level.
Remove dipstick to check the oil level. If oil
level is below the lower limit mark, add oil to
the specified upper limit mark.
Dipstick
Oil change
Shut off the engine and remove dipstick.
Remove the oil drain plug on the bottom-left
of crankcase to drain oil.
After draining out oil, clean oil plug and its
+-gasket and reinstall. Replace the gasket if
it is damaged.
Torque value:1.0~1.5 kgf-m
Caution
Warm up the engine. This will make the oil
flow out easily.
Add oil to the specified capacity.
Oil Viscosity: SAE 10W-30, recommended
using King-Mate serial oil.
Engine oil capacity:
Disassembly: 850cc`
Change:
750cc
When checking for oil leak, run the engine at
idle speed for a few minutes, then check oil
capacity with dipstick.
Cleaning the oil strainer
Drain oil from engine, remove the strainer
cover, spring and strainer.
If there is an accumulation on the screen,
wash it off with suitable solvent
(recommended using compressed air).
Check O-ring for damage, replace if
necessary.
Reinstall strainer, spring, O-ring and strainer
cover.
Torque value: 1.0~2.0 kgf-m
Oil drain plug
strainer cover
oil strainer
spring
2-3
Gear Oil
Inspection
Check gear oil if leaking.
Park the motorcycle with main stand on flat
level place.
Turn off engine and remove the gear oil
draining plug.
Place a measurement cup under the draining
hole.
Remove the oil drain plug and drain gear oil
into a measurement cup.
Check gear oil if enough.
Replacement
At first, remove the gear oil refilling bolt, and
then remove the draining plug.
Install the draining plug after drained oil out.
Torque value:1.0~1.5 kgf-m
SYM
Gear oil refilling bolt
Caution
Inspect if washer is in good condition.
Replace it with new one if it was deformed
or damaged.
Fill out gear oil to specified quantity from the
engine oil filling hole.
Install the oil filling bolt.
Quantity: 90 c.c.
Recommended: SAE 85W-140.
Gear oil draining plug
Fuel System
Fuel Pipe
Remove luggage box, rear center cover,
body cover, and rear fender, as well as front
inner box.
Check all pipes, and replace it when they are
deterioration, damage or leaking.
Warning
Gasoline is a low ignition material so any
kind of fire is strictly prohibited as dealing
it.
Fuel filter
Remove the fuel tank.
Remove fuel pipe from the fuel filter.
Replace the fuel filter with new one.
Install the fuel filter.
Caution
The arrow on the fuel filter means the flow
direction of fuel and check it if leaking after
installation.
2-4
Fuel filter
SYM
AIR CLEANER
Element
Remove 7 screws from the air cleaner cover.
Remove element of air cleaner (2 screws).
Check the element if dirt or damaged.
Replace it with new one if dirt or damaged.
screws7
Caution
Air cleaner element contains a paper
made filter so do not try to clean it.
Make sure that the air cleaner cover had
been installed properly after installation.
Air cleaner element
THROTTLE VALVE OPERATION

Have a wide open of throttle valve as handle
bar in any position and release it to let back
original (full closed) position.
Check handle bar if its operation is smooth.
Check throttle valve cable and replace it if
deteriorated, twisted or damaged.
Lubricate the cable if operation is not
smooth.
Measure handle bar free play in its flange
part.
Free play2~6 mm
Adjustment can be done in either ends.
Secondary adjustment is conducted from top
side.
Remove rubber boot, loosen fixing nut, and
then adjust it by turning the adjustment nut.
2~6 mm
Rubber boot
Fixing nut
Adjustment nut
2-5
Primary adjustment is conducted from button
side.
Loosen fixing nut, and adjust by turning the
adjustment nut.
Tighten the fixing nut, and check
acceleration operation condition.
SYM
Adjustment nut
Fixing nut
Caution
When always riding in rainy area or full
throttle position, maintenance period must
be shorted. The deposits can be seen in
the transparent section of draining hose.
VALVE CLEARANCE ADJUSTMENT
Inspection hole
Caution
Checks and adjustment must be performed
when engine is cold (below 35).
Remove luggage box and front center cover.
Remove the left body cover & left side cover.
Remove cylinder head cap.
Remove the ignition timing check hole on the
cooling fan cover.
With T type wrench, turn crankshaft in
clockwise motion so that mark (T) on the
generator flywheel aligns with the mark on
the crankshaft, and camshaft is at TDC
position also as same as level of cylinder
head top-end. A single hole on camshaft
sprocket is forward to up. (Piston is at TDC
position in the compression stroke.)
Caution
The crankshaft can not be rotated in
counter-clockwise to prevent from damage
so that valve clearance can not be
measured.
2-6
TDC mark
Ignition timing mark
SYM
VALVE CLEARANCE INSPECTION

AND ADJUSTMENT
Feeler gauge
Check & adjust valve clearance with feeler

gauge.
Valve clearance (IN/EX): 0.060.02 mm
Loosen fixing nut and turn the adjustment
nut for adjustment.
Caution
It has to make sure that valve-rocker arm is
be adjusted to standard level when
adjusting it, and re-check the valve
clearance after tightened the fixing nut.
Fixing nut
CARBURETOR IDLE SPEED

ADJUSTMENT
Caution
Inspection & adjustment for idle speed
have to be performed after all other parts
in engine that needed adjustment have
been adjusted.
Idle speed check and adjustment have to
be done after engine is being warm up
(around 10 minutes).
Park the motorcycle with main stand and
warn up engine.
Open the carburetor cover from the luggage
box.
Turn the throttle valve stopper screw to
specified idle speed.
Specified idle speed: 2100100 rpm
Emission adjustment in Idle speed
Warm up the engine for around 10 minutes
and then conduct this adjustment.
1. Connect the tachometer onto engine.
2. Adjust the idle speed adjustment screw and
let engine runs in 2100100 rpm.
3. Insert the exhaust sampling muffler of
exhaust analyzer into the front section of
exhaust pipe. Adjust the air adjustment
screw so that emission value in idle speed
is within standard.
4. Slightly accelerate the throttle valve and
release it immediately. Repeat this for 2~3
times.
5. Read engine RPM and value on the
exhaust analyzer. Repeat step 2 to step 4
procedures until measured value within
standard.
Exhaust Emission:
CO: 12.0g/km
HC: 1.0g/km
Ignition coil cable
Throttle valve stopper screw
Air adjustment screw
2-7
SYM
IGNITION SYSTEM
F mark
Ignition timing
Caution
C.D.I ignition system is set by manufacturer
so it can not be adjusted.
Ignition timing check procedure is for
checking whether C.D.I. function is in normal
or not.
Ignition light
Remove ignition timing hole cap located on

the cooling fan cap, or remove the cooling
fan cap.
Check ignition timing with ignition light.
Start engine and set engine idle speed in
2100100 rpm, and if the mark aligns with
the F, then it means that ignition timing is
correct.
Increase engine speed to 8000 rpm to check
ignition timing advance. If the detent aligns
with advance mark , then it means ignition
timing advance is in functional. If not,
check CDI set, pulse flywheel, and pulse
generator. Replace these components if
malfunction of these parts are found.
SPARK PLUG
Appointed spark plug: TORCH A7RC
Remove luggage box.
Remove center cover.
Remove spark plug cap.
Clean dirt around the spark plug hole.
Remove spark plug.
Measure spark plug gap.
Spark plug gap: 0.6~0.7 mm
Carefully bend ground electrode of the plug
to adjust the gap if necessary.
Screw the park plug into the plug hole with
hands, then tighten the plug with a wrench to
prevent from damaging the spark plug's
thread.
Connect spark plug cap.
Spark plug cap
Side electrode
0.6~0.7mm
0.6~0.7mm
2-8
Center electrode
SYM
CYLINDER COPMRESSION PRESSURE

Warn up engine and then turnoff the engine.
Remove the luggage box and the center
cover.
Remove spark plug cap and spark plug.
Install compression gauge.
Full open the throttle valve, and rotate the
engine by means of stepping the
kick-starting lever.
Caution
Rotate the engine until the reading in the
gauge no more increasing.
Usually, the highest pressure reading will be
obtained in 4~7 seconds.
Spark plug cap
Compression pressure: 11.80.4:1 kg/cm.

Check following items if the pressure is too
low:
Incorrect valve clearance
Valve leaking
Cylinder head leaking, piston, piston ring
and cylinder worn out
If the pressure is too high, it means carbon
deposits in combustion chamber or piston
head.
Cylinder
pressure
gauge
Gear teeth
DRIVING SYSTEM
DRIVING BELT
Remove left side cover.
Remove mounting bolt located under air
cleaner.
Remove 9 bolts of the engine left crankcase.
Remove the left crankcase cover.
Check if the belt is crack or worn out.
Replace the belt if necessary or in accord
with the periodical maintenance schedule to
replace it.
Width limit: above 18.5 mm
Clutch pad
Start the motorcycle and gradually increase
throttle valve openness to check clutch pad
operation.
If the motorcycle moves with shaking, then
check its clutch pad for wearing. Replace it
if necessary.
Width
Clutch pad
Clutch
2-9
SYM
STEERING SYSTEM
Caution
Check all wires and cables if they are
interfered with the rotation of steering
handle bar.
Lift the front wheel out of ground.
Turn handle from right to left and check if
turning is smoothly.
If handle turning is uneven and bending, or
the handle can be operated in vertical
direction, then adjust the handle top bearing.
SUSPENSION SYSTEM
Warning
Do not ride the motorcycle with poor
shock absorber.
Looseness, wear or damage shock
absorber will make poor stability and
driveability.
Front shock absorber
Hold front brake lever and press down the
front shock absorber for several times to
check its operation.
Hold front brake lever and push forward the
front shock absorber for several times to
check its locking status.
Check if it is scratched or leaking.
Replace damaged and non-repairable
components.
Tighten all nuts and bolts.
Rear Shock absorber
Press down the rear shock absorber for
several times to check its operation.
Check if it is scratched or leaking.
Replace damaged and non-repairable
components.
Park the motorcycle with main standard.
Start engine and let the rear wheel rotate
after increased engine rpm. Check engine
for any parts loose or shaking. Also check
the engine suspension bushing for wear out.
Replace the bushing if worn out.
Tighten all nuts and bolts.
2-10
Rear Shock absorber
SYM
FRONT DISC BRAKE SYSTEM

BRAKE SYSTEM HOSE
Make sure the brake hoses for corrosion or
leaking oil, and also check brake system for
leaking.
Brake hose
BRAKE FLUID
Check brake fluid level in the brake fluid
reservoir. If the level is lower than the
LOWER limit, add brake fluid to UPPER limit.
Also check brake system for leaking if low
brake level found.
Caution
In order to maintain brake fluid in the
reservoir in horizontal position, do not
remove the cap until handle bar stop.
Do not operate the brake lever after the
cap had been removed. Otherwise, the
brake fluid will spread out if operated the
lever.
Do not mix non-compatible brake fluid
together.
FILLING OUT BRAKE FLUID
Tighten the drain valve, and add brake fluid.
Place the diaphragm in.
Operate the brake lever so that brake fluid
contents inside the brake system hoses.
AIR BLEED OPERATION

Connect a transparent hose to draining
valve.
Hold the brake lever and open air bleeding
valve. Perform this operation alternative until
there is no air inside the brake system
hoses.
Lower limit
Brake fluid cap

Low brake level
bubble
drain valve
Caution
Before closing the air bleed valve, do not
release the brake lever.
transparent draining hose
2-11
ADDED BRAKE FLUID
Add brake fluid to UPPER limit lever.
Recommended brake fluid: DOT3 or DOT4
WELL RUN brake fluid.
SYM
Brake fluid cap
Low limit
Caution
Never mix or use dirty brake fluid to prevent
from damage brake system or reducing
brake performance.
BRAKE LINING WEAR

The indent mark on brake lining is the wear
limitation.
Replace the brake lining if the wear limit
mark closed to the edge of brake disc.
Brake ling wear limit
Caution
It is not necessary to remove brake hose
when replacing the brake lining.
Brake clipper
Remove the brake clipper bolt, and take out

the clipper.
Caution
Do not operate the brake lever after the
clipper removed to avoid clipping the brake
lining.
Brake
clipper
bolts x 2
Pry out the brake lining with a flat driver if

lining be clipped.
Remove brake lining bolt.

Take out the lining.
Caution
In order to maintain brake power balance,
the brake lining must be replaced with one
set.
2-12
bolts x 2
Brake disc
SYM
DRUM BRAKE SYSTEM

Front Brake Free Play: (Drum brake)
Measure free play of rear brake level at the
end of the lever.
Free play: 10-20 mm
Adjust the free play by turning the front brake

adjustment nut if necessary.
1020mm
mark
Increasing free
play
Decreasing free play
REAR BRAKE FREE PLAY: (DRUM

BRAKE TYPE)
Measure the free play of the front brake lever
at the end of the lever.
Free play: 10-20 mm
Adjust the free play by turning the front brake
adjustment nut if necessary.
Adjustment nut
Adjustment nut
Decreasing
free play
Increasing
free play
BRAKE CONFIRAMTION
Caution
marks
After brake adjustment, it has to check

the brake operation to make sure the
front and rear wheel can be braked.
Pull the brake lever, and make sure that
the wear limit marks of brake ling on the
both front & rear brake arm are closer
and touch to the marks. If so,
replace the brake ling with new one.
2-13
BRAKE LIGHT SWITCH
The brake light switch is to lit up brake light
as brake applied.
Make sure that electrical starter can be
operated only under brake applying.
SYM
Brake light switch
WHEEL/TIRE
Check if both front and rear tire pressure are
within specification.
Caution
Tire pressure check should be done as cold
tire.
Appointed tire pressure
Tire size
Front tire Rear tire
Load for
1.75
2.00
Tire
single
pressure
Load for
as cold tire
2.25
two
1.75
(Kg/cm)
persons
Appointed Tire
Front/Rear wheel:
110/70-12(47J)/120/70-12(51J)
Check if tire surface is ticked with nails,
stones or other materials.
Check if tire surface or wall for crack or
damaged, and replace it if necessary.
The tire tread depth can be checked by
visual inspection or depth gauge.
Replace the tire if tire tread dent or
unusual wearing out.
The tire should be replaced if the wear
limit mark () is in visible.
Measure tire thread depth from tire center
surface.
Replace the tire if the depth is not come with
following specification:
Front tire: 1.5 mm
Rear tire: 2.0 mm
Caution
The wear limit marks () are located
around the tire wall even for inspection.
2-14
Wear limit indictor
mark
SYM
BATTERY
Battery cover screws
Battery Removal
Remove the 4 screws on the floor panel.
Remove battery cap. (4 screws)
Battery cables removal:
1. At first, remove the negative - cable.
2. Then, remove the positive + cable.
3. Remove the battery.
If there is some rust on battery posts, clean it
with steel brush.
Install the battery in the reverse procedures
of removal.
Caution
If there is rust on the posts very serious,
spray some hot water on the posts.
Then, clean it with steel brush so that
can remove rust for more easily.
Apply some grease on the posts after
rust removed to prevent from rust again.
HEADLIGHT ADJUSTMENT
Turn the headlight adjustment bolt. And
adjust the headlight beam height.
Then, tighten the adjustment bolt after the
beam height in proper position.
Headlight adjustment bolt
Caution
To adjust the headlight beam follows
related regulations.
Improper headlight beam adjustment will
make in coming driver dazzled or
insufficient lighting.
NUTS, BOLTS TIGHTENESS

Perform periodical maintenance in accord
with the Periodical Maintenance Schedule.
Check if all bolts and nuts on the frame are
tightened securely.
Check all fixing pins, snap rings, hose (pipe)
clamps, and wire holders for security.
2-15
SYM
3. LUBRICATION SYSTEM
MECHANISM DIAGRAM ....................3-1

OPERATIONAL PRECAUTIONS .......3-2
TROUBLE DIAGNOSIS......................3-2
ENGINE OIL .......................................3-3
CLEANING ENGINE OIL STRAINER... 3-3

OIL PUMP ............................................ 3-4
GEAR OIL ............................................ 3-7
MECHANISM DIAGRAM
Valve rocker
arm
Forcedly lubrication
Camshaft
Scoop lubrication
Inner passage
Connecting rod
Forcedly
lubrication
Crankshaft
Oil strainer
Oil pump
3-1
SYM
OPERATIONAL PRECAUTIONS
General Information
This chapter contains maintenance operations for the engine oil pump, engine oil and
gear oil.
Oil viscosity
Specifications
Engine oil quantity
Disassembly 800 c.c.
Replacement 750 c.c.
Oil viscosity
SAE 10W-30 or equivalent

Use SAE 5W-40 when
outside temperature is
below 0.
Gear Oil
Disassembly 110 c.c.

Replacement 100 c.c.
Oil viscosity of gear oil: SAE 85W-140
Items
Oil pump
Standard
Inner rotor clearance

Clearance between outer
rotor and body
Clearance between rotor
side and body
Torque value
Engine oil drain plug
Engine oil filter screen cap
Gear oil drain bolt
Oil pump fixing screws
unit : mm
Limit
0.12
0.12
0.05~0.10
0.20
1.0~1.5kgf-m
1.0~2.0kgf-m
1.0~1.5kgf-m
1.0~1.5kgf-m
0.8~1.2kgf-m
TROUBLE DIAGNOSIS
Low engine oil level
Oil leaking
Valve guide or seat worn out
Piston ring worn out
Low Oil Pressure
Low engine oil level
Clogged in oil strainer, circuits or pipes
Oil pump damage
3-2
Dirty oil
No oil change in periodical
Cylinder head gasket damage
Piston ring worn out
SYM
ENGINE OIL
Turn off engine, and park the motorcycle in
flat ground with main stand.
Check oil level with oil dipstick after 3-5
minutes.
Do not rotate the dipstick into engine as
checking.
If oil level is nearly low level, fill out
recommended oil to upper level.
Dipstick
Oil Replacement
Caution
Drain oil as engine warmed up so that
make sure oil can be drained smoothly and
completely.
Place an oil pan under the motorcycle, and
remove oil strainer cap.
Make sure if the aluminum washer of the
draining bolt is damaged. If so, replace it
with new one.
Install the drain bolt and tighten it.
Oil drain plug
CLEANING ENGINE OIL STRAINER

Remove the oil strainer cap.
Remove oil strainer and spring.
Clean oil strainer (recommended using
compressed air to clean dirty foreign).
Check if the strainer and O-ring of the oil
strainer are broken. Replace with new one if
found.
Install the oil strainer and spring.
Install the oil strainer cap and tighten it.
Fill out oil to the oil filler (Oil viscosity SAE
10W-30)
Use SAE 5W-40 when outside temperature
is below 0.
Engine oil quantity: Replacement 750 c.c.
Oil strainer cap
oil strainer
spring
3-3
SYM
OIL PUMP
Oil Pump Removal
Remove the alternator (refer to chapter10).
Remove the engine right crankcase cover.
Make sure that the pump axle can be rotated
freely.
Remove the oil pump driving gear nut.
pump driving
gear nut
3 bolts
Remove oil pump body bolts (3 bolts).
Remove the oil pump pin.

Remove the oil pump.
pin
Remove the 2 O-rings.
3-4
2 O-rings
SYM
Oil Pump Inspection

Check the clearance between oil pump body
and outer rotor.
Limit: below 0.12 mm
Check clearance between inner and outer

rotors.
Limit: below 0.12 mm
Check clearance between rotor side face

and pump body.
Limit: below 2.0 mm
Oil Pump Re-assembly

Install inner and outer rotors into the pump
body.
Align the indent on driving shaft with that of
inner rotor. Install the driving shaft.
Install the oil pump cover and fixing pin
properly and then tighten screw. (1 screw)
Drive shaft
Oil pump body

Fixing pin
inner rotor
outer rotor
Oil pump
cover
3-5
Oil Pump Installation
Install the 2 O-rings.
SYM
2 O-rings
Install the oil pump pin.
pin
3 bolts
Install the oil pump.

Install the oil pump body bolts (3 bolts).
Install the oil pump driving gear nut.

Install the alternator (refer to chapter10).
Install the engine right crankcase cover.
pump driving
gear nut
3-6
SYM
GEAR OIL
Filling bolt
Oil Level Inspection

Park the motorcycle on flat ground with main
stand.
Turn off engine and remove both engine oil
filling bolt and oil draining bolt.
Remove gear oil filling hole bolt and place a

measurement cup under the draining plug.
Remove the oil draining plug and the pour
gear oil into the measurement cup.
Measure the gear oil quantity if within
standard value.
Add specified gear oil if the oil level too low.
Standard quantity: 110cc.
Replacement: 100 cc.
Draining bolt
Gear Oil Replacement

Remove the gear oil filling bolt and its
draining plug and then drain oil completely.
Install the draining plug and tighten it. (Make
sure if the plug washer is damaged. If so,
replace it with new one.)
Torque Value1.0~1.5 kgf-m
Add new gear oil (100 c.c.) from the gear oil
filling hole and then install the gear oil filling
hole bolt after added oil. And then, tighten
the bolt.
Torque Value: 1.0~1.5 kgf-m
Recommended to apply with SAE
85W-140.
Start engine and run it for 2~3 minutes.
Turn off engine and check if oil leaking.
3-7
SYM
4. FUEL SYSTEM
MECHANISM ILLUSTRATION ............. 4-1

PRECAUTIONS IN OPERATION ......... 4-2
TROUBLE DIAGNOSIS........................ 4-3
CARBURETOR REMOVAL .................. 4-4
VACUUM CHAMBER ........................... 4-4
AIR CUT-OFF VALVE ..........................4-6
AUTO BY-STARTER .......................... 4-7

FLOAT CHAMBER ............................. 4-8
INSTALLATION OF CARBURETOR .. 4-9
IDLE SPEED ADJUSTMENT.............. 4-9
FUEL TANK ........................................ 4-10
AIR CLEANER.................................... 4-11
MECHANISM ILLUSTRATION
Carburetor
Fuel strainer
Fuel unit
Fuel tank cap
4-1
4. FUEL SYSTEM
SYM
General Information
Warning
Gasoline is a low ignition point and explosive materials, so always work in a well-ventilated
place and strictly prohibit flame when working with gasoline.
Cautions
Do not bend or twist throttle valve cable. Damaged cable will make unstable driveability.
When disassembling fuel system parts, pay attention to O-ring position, replace with new
one as re-assembly
There is a drain screw in the float chamber for draining residual gasoline.
Do not disassemble automatic by-starter and air cut-off valve arbitrarily.
Specification
Item
Specification
Main jet
85#
Slow jet
35#
Idle speed
2100100 rpm
Fuel quantity
adjustment screw
1 1/23/4 turns
Level in float chamber
3.51 mm
Jet needle
DA8CD add 2 units 0.5mm washer
Throttle handle free play
2~6 mm
Torque value
Fuel valve tightening nut: 1.5~2.0 Kgf-m
Tool
Special service tools
Vacuum/air pressure pump
General service tools
Fuel level gauge
4-2
SYM
4. FUEL SYSTEM
TROUBLE DIAGNOSIS
Poor engine start
No fuel in fuel tank
Clogged fuel tube
Too much fuel in cylinder
No spark from spark plug (malfunction of
ignition system)
Clogged air cleaner
Malfunction of automatic by-starter
Malfunction of throttle valve operation
Stall after started

Malfunction of carburetor
Dirty engine oil
Air existing in intake system
Incorrect idle speed
Rough idle
Malfunction of ignition system
Incorrect idle speed
Dirty fuel
Power insufficiency and fuel consuming

Fuel system clogged
Mixture too lean

Clogged fuel injector
Vacuum piston stick and closed
Malfunction of float valve
Fuel level too low in float chamber
Clogged fuel tank cap vent
Clogged fuel filter
Obstructed fuel pipe
Clogged air vent hose
Air existing in intake system
Mixture too rich

Clogged air injector
Malfunction of float valve
Fuel level too high in float chamber
Dirty air cleaner
Intermittently misfire as acceleration

Late ignition timing

4-3
4. FUEL SYSTEM
CARBURETOR REMOVAL
SYM
throttle valve cable
clamp strip of isolator
Remove the luggage box.

Loosen the adjustment nut and fixing nut of
throttle valve cable, and release the cable
from carburetor.
Remove fuel pipe, vacuum hose.
Disconnect auto by-starter connectors.
Release the clamp strip of air cleaner.
Release the clamp strip of carburetor isolator.
Take the carburetor out..
vacuum hose
vacuum hose
auto by-starter
Screws2
VACUUM CHAMBER
Removal
Loosen drain screw, and drain out residual
fuel in float chamber.
Remove screws (2 screws) of vacuum
chamber cover and the cover.
Vacuum Chamber cover
Remove compress spring and vacuum

piston.
Vacuum piston
compress
spring
4-4
SYM
Remove fuel needle seat, spring, and
injector needle.
Check if the vacuum piston for wear out,
crack or other damage.
Check if the diaphragm for damage or crack.
Cautions
4. FUEL SYSTEM
fuel needle
seat
fuel needle
spring
injector
needle
Do not damage vacuum diaphragm.
piston
Installation
Install injector needle, spring and fuel needle
seat to vacuum piston.
Piston spring
piston diaphragm lock position
Cautions
Note direction as installing the piston
set because wrong direction of the
piston cab not be installed.
Align the indent of vacuum
diaphragm with the carburetor body.
Install vacuum piston to carburetor body.
Install compress spring.
Screws2
Install vacuum chamber cover and tighten 2

screws.
Vacuum Chamber cover
4-5
4. FUEL SYSTEM
ACCELERATE PUMP
Removal
Loosen the fixing screws from carburetor.
Remove the accelerate pump drive arm from

the carburetor.
Remove 3 mounting screws and remove the

float chamber cover.
Installation
Install the valve as reverse order of removal.
Cautions
Do not damage the vacuum diaphragm or
in opposite installation direction.
4-6
SYM
Screws 2
Accelerate pump
drive arm
SYM
4. FUEL SYSTEM
AUTO BY-STARTER
Inspection
Turn off engine and waiting for over 10
minutes for cooling.
Check resistance across the two terminals of
the auto by-starter
Resistance value: Max. 10 (Measured
after engine stopped for more than 10
minutes)
Replace the auto by-starter with a new one if
resistance value exceeds standard.
Remove the carburetor, allow it to cool off for
30 minutes.
Connect a hose to fuel richment circuit.
Pump compressed air to the circuit.
Replace the auto by-starter if the circuit
clogged.
Connect battery posts (12V) to starters
connectors. After 5 minutes, test the rich
circuit with compressed air. If air flow through
the circuit, then replace the starter.
Removal
Remove fixing plate screw, and then remove
the plate and auto by-starter from carburetor.
auto by-starter
round point
Screw
Valve inspection
Check if auto by-starter and valve needle for
damage or wear out.
fixing plate
Screw
Installation
Install auto by-starter to the carburetor body.
Install fixing plate to the upper groove of auto
by-starter, and install its flat surface to
carburetor. Install screw and tighten it.
Cautions
Align the round point of the starter with
the screw hole of air intake side.
fixing plate
valve needle
4-7
4. FUEL SYSTEM
FLOAT CHAMBER
Disassembly
Remove the float pin and float valve.
SYM
screws 3
float
float pin
Checking
Check float needle valve and valve seat for

drop difference damage, wear out, dirty or
clogged.
float pin
float needle
valve
Cautions
In case of worn out or dirt, the float needle
valve and valve seat will not tightly close
causing fuel level to increase and as a
result, fuel flooding. A worn out or dirty float
needle valve must be replaced with a new
one.
float pin
float
Remove main jet,slow jet, fuel amount

adjustment screw.
Cautions
slow jet
fuel amount
adjustment screw
Take care not to damage jets and adjust

screw.
Before removing adjustment screw, turn it
all the way down and note the number of
turns.
Do not turn adjustment screw forcefully to
avoid damaging valve seat face.
main jet
Clean jets with cleaning fluid.

Then use compressed air to blow dirt off.
Blow carburetor body passages with
compressed air.
slow jet
4-8
main jet
SYM
4. FUEL SYSTEM
Installation
Install main jet, slow jet and fuel amount
adjustment screw.
Cautions
fuel amount
adjustment screw
Set the adjustment screw in according to number

of turns noted before it was removed.
Install the float needle valve, float and float pin.
Checking Fuel Level

Cautions
Check again to ensure float valve, float for
proper installation.
To ensure correct measurement, position
the float meter in such a way so that float
chamber face is vertical to the main jet.
Fuel level: 3.51 mm
INSTALLATION OF CARBURETOR
Install carburetor in the reverse order of removal.
Following adjustments must be made after
installation.
Throttle valve cable clearance adjustment
Idle speed adjustment
float meter
throttle valve
stopper screw
IDLE SPEED ADJUSTMENT

Caution
Fuel amount adjust screw was set at factory,
so no adjustment is needed. Note the
number of turns it takes to screw it all the
way in for ease of installation.
Never screw in forcedly to avoid damaging
the screw seat.
The main stand must be used to support the
motorcycle to perform the adjustments.
Use a tachometer when adjusting engine RPM.
Screw in adjustment screw gently, then back up to
standard turns.
Throttle valve cable

adjustment nut
Standard turns: 1 1/23/4 turns

Warm up engine, adjust throttle valve stopper
screw to standard RPM.
Idle speed rpm: 2100100 rpm

Connect the sampling hose of exhaust analyzer to
exhaust front end. Press test key on the analyzer.
Adjust the air volume adjustment screw and read
CO reading on the analyzer.
CO standard value: 1.0~1.5 %

Accelerate in gradual increments, make sure both
rpm and CO value are in standard values after
engine running in stable. If rpm and CO value
fluctuated, repeat the procedures described above
for adjusting to standard value.
air volume
adjustment screw
4-9
4. FUEL SYSTEM
SYM
FUEL TANK
Fuel unit connector
Fuel unit removal

Open the seat.
Remove the luggage box. (6 bolts)
Remove the engine starter control switch
wire connector .
Disconnect fuel unit connector.
Remove fuel unit.
Cautions
Do not bend the float arm of fuel unit.
Do not fill out too much gasoline to
fuel tank.
Fuel unit inspection. (Refer to chapter 16 electrical equipment).
Fuel unit installation
Install the gauge in the reverse order of
removal.
fuel unit
Cautions
Do not forget to install the gasket of fuel unit
or damage it.
gasket
FUEL TANK REMOVAL

Open the seat.
Remove the luggage box assembly (6 bolts).
Disconnect the engine start control switch
connector.
Disconnect the fuel unit connector.
Remove the fuel pipe, fuel filter.
Remove the fuel tank (2 bolts).
Fuel Tank Installation

Install the tank in the reverse order of
removal.
4-10
SYM
AIR CLEANER
4. FUEL SYSTEM
air filter strap
Removal
Remove the seat .
Remove the luggage box assembly (4 bolts).
Loosen the clamp strip of air cleaner.
Remove evaporative return hose.
Remove the air cleaner body bolts (2 bolts).
Remove the air cleaner.
Installation
Install the air cleaner in the reverse order of
removal.
bolts2
Air Cleaner Element Cleaning

Remove the air cleaner cover (7 screws).
screws7
Remove the air cleaner element (2 screws).

With compressed air to clean dirty around
the element. Replace it if it is too dirty to
clean.
Cautions
The air cleaner element is made of paper
so do not soap it into water or wash it
with water.
Air cleaner element
4-11
SYM
5. REMOVAL OF ENGINE
MECHANISM DIAGRAM ...................... 5-1

OPERATIONAL PRECAUTIONS ......... 5-2
ENGINE REMOVAL ............................. 5-3
. 5-6
ENGINE SUSPENSION FRAME.......... 5-7
INSTALLATION OF ENGINE ............... 5-8
REMOVAL OF ENGINE SUSPENSION BUSHING
MECHANISM DIAGRAM
3.5~4.5kgf-m
4.5~5.5kgf-m
4.5~5.5kgf-m
2.4~3.0kgf-m
4.5~5.5 kgf-m
5-1
SYM
General Information
Engine must be supported by a bracket or adjustable tool in height.
The following parts can be serviced with the engine installed on the frame.
1. Carburetor
2. Driving disk, driving belt, clutch, and transporting disk
3. Final reduction gear mechanism
Specification
Specification
Engine Oil Capacity
Gear Oil Capacity
Disassemble
800 c.c.
Replacement
750 c.c.
Disassemble
110 c.c.
Replacement
100 c.c.
Torque Values
Engine suspension bolt (frame side)
Engine suspension nut (engine side)
Bolt of rear shock absorber upper connection
Bolt of rear shock absorber lower connection
5-2
4.5~5.5kgf-m
4.5~5.5kgf-m
3.5~4.5kgf-m
2.4~3.0kgf-m
SYM
ENGINE REMOVAL
Open the seat.
Remove the luggage box assembly (6
bolts ).
Disconnect the engine start control switch
connector.
Remove the power connector of auto bystart.
Remove the generator wire and pulse
generator connector.
pulse generator
connector
Generator
connector
Auto by-start
connector
Remove the starter motor wire on the Starter

magnetic switch.
Starter magnetic switch
Remove the spark plug.
Spark plug
5-3
SYM
Remove the fuel pipe, vacuum hose, and

throttle valve cable from the carburetor.
Loose the strap screw of the air cleaner
guide, and then the air cleaner guide.
Remove the exhaust muffler (Bolts

2, Nuts 2).
Bolts2
Remove the rear wheel (Nut 1).
Nut 1
2 bolts
Remove the air cleaner connection bolts (2

bolts).
5-4
SYM
Brake cable nut
Remove the rear brake cable nut.

Remove the rear brake cable.
Remove the rear shock absorber lower bolt.
Rear shock
absorber bolt
Loose the strap screw of engine left guide,

and then remove the engine left guide.
Strap screw of guide
Remove the engine suspension nut and bolt

(engine side), and then remove the engine.
Caution
With a bracket to support the engine
to prevent from it damage by falling
down as removing the engine.
Engine suspension bolt/nut
Check if the engine suspension, rear shock

absorber bushing, and cushion rubber for
damage. Replace them with new ones if so.
Bushing
5-5
REMOVAL OF ENGINE
SUSPENSION BUSHING
If engine suspension frame and the cushion
rubber of rear shock absorber bushing
damaged. Then, with the bushing remover /
presser, 28mm &20mm, to press the
bushing out, and replace it with new one.
Engine suspension bushing: 28mm
Rear shock absorber bushing: 20mm
Pressing out
Place the detent section of the bushing
remover toward the bushing, and drive both
the pressing ring and bolt in to press the
bushing out.
Pressing In
Place the flat section of the remover toward
the bushing, and then drive the bushing,
pressing ring, and bolt in to install the
bushing.
5-6
SYM
SYM
ENGINE SUSPENSION FRAME

Removal
Remove the right side bolt of engine
suspension frame.
Remove the left side bolt of engine

suspension frame.
Bolt of engine suspension

frame (left side)
Check if the engine suspension frame

bushing and cushion rubber for damage. If
so, replace with new ones.
Installation
Tighten the bolts and nuts of engine
suspension frame.
Engine suspension frame nut:
Torque Value: 4.5~5.5 kgf-m
5-7
INSTALLATION OF ENGINE
SYM
Engine suspension nut1
Check if the bushings of engine suspension

frame and shock absorber for damaged. If so,
replace with new ones.
Install the engine according to the reversing
order of removal.
Caution
Notice both feet and hands safety for
squeezing as engine installation.
Do not bent or squeeze each wires or
hose.
Route all cables and wires in
accordance with the routine layout.
Brake cable nut
Engine suspension nut:

Torque Value: 4.5~5.5kgf-m
Rear shock absorber bolt:
Torque Value: Top: 3.5~4.5kgf-m
lower: 2.4~3.0kgf-m
Rear wheel axle nut:
Torque Value: 11.0~13.0kgf-m
Rear shock
absorber bolt
Rear wheel axle nut1
5-8
SYM
6. CYLINDER HEAD/VALVE

TROUBLE SHOOTING.......................6-3
CAMSHAFT REMOVAL .....................6-4
CYLINDER HEAD REMOVAL ............6-6
CYLINDER HEAD DISASSEMBLY ....6-7
CYLINDER HEAD INSPECTION.......... 6-8

VALVE SEAT INSPECTION AND SERVICE 6-10
CYLINDER HEAD REASSEMBLY ....... 6-12
CYLINDER HEAD INSTALLATION ...... 6-13
CAMSHAFT INSTALLATION ............... 6-13
VALVE CLEARANCE ADJUSTMENT .. 6-14
MECHANISM DIAGRAM
0.8~1.2 kgf-m
0.7~1.1 kgf-m
1.0~1.4 kgf-m
1.0~1.4 kgf-m
0.8~1.2 kgf-m
6-1
SYM
General Information
This chapter is contained maintenance and service for cylinder head, valve, and camshaft
as well as valve rocker arm.
Cylinder head service cannot be carried out when engine is in frame.
Specification
Camshaft
Rocker
arm
unit: mm
Item
Standard
Limit
Compression pressure
12 kg/cm
Intake
25.686~25.786
25.29
Exhaust
25.50~25.60
25.12
ID of valve rocker arm
10.000~10.015
10.10
OD of valve rocker arm shaft
9.972~9.987
9.910
Intake
4.975~4.99
4.90
Exhaust
4.955~4.97
4.90
5.000~5.015
5.030
Intake
0.010~0.037
0.080
Exhaust
0.030~0.057
0.100
Outer
35.25
Inner
32.26~32.56
Height of cam lobe
OD of valve stem
ID of Guide
Valve
Clearance between
valve stem and guide
Free length of valve
spring
Torque Value
Cylinder head cover bolt
Cylinder head bolt (LH)
Bolt of timing chain auto-adjuster
Spark plug
Cam holder nut
Valve adjustment fixing nuts
TOOLS
Valve reamer: 5.0mm
Valve guide driver: 5.0mm
Valve spring compressor
6-2
0.8~1.2kgf-m
0.8~1.2kgf-m
0.8~1.2kgf-m
1.0~1.4kgf-m
1.0~1.4kgf-m
1.0~1.4kgf-m
SYM
TROUBLE SHOOTING
Engine performance will be effected by troubles on engine top end. The troubles usually can
be determinate or by performing cylinder compression test and judging the abnormal noise
generated.
Rough Idle
Low compression pressure.
Low compression pressure
1. Valve
Improper valve adjustment.
Burnt or bended valve.
Improper valve timing.
Valve spring damaged.
Valve carbon.
Poor sealing on valve seat.
Improper spark plug installation.
2. Cylinder head
Cylinder head gasket leaking or damage.
Tilt or crack cylinder surface.
3. Piston
Piston ring worn out.
High compression pressure
Too much carbon deposit on combustion chamber or piston head.
Noise
Improper valve clearance adjustment
Burnt valve or damaged valve spring
Camshaft wear out or damage
Cam chain wear out or looseness
Auto-adjuster wear out or damage of cam chain
Camshaft sprocket wear out
Rocker arm or rocker arm shaft wear out
White smoke
Valve guide or valve stem wear out
Valve stem seal wear out
6-3
CAMSHAFT REMOVAL
SYM
Blow-by hose
Remove the shroud of the engine.

Remove the crankcase blow-by system hose
from the cylinder head.
Remove the cylinder head bolts and then
remove the cylinder head (4 bolts).
A.I.
4 bolts
Loosen the bolt of camshaft chain adjuster in

a counter-clockwise motion for release
adjuster.
bolt
camshaft chain adjuster
Turn the flywheel in counter clockwise

motion with T type wrench until the T mark
on flywheel aligned with the mark on the
crankcase so that the hole on the camshaft
sprocket is forward up and piston is at TDC
position.
Hole
TDC mark
Remove camshaft holder nut and washer.

Caution
Loosen the nuts diagonally by 2-3
sequences.
4 nuts
6-4
SYM
Remove the camshaft holder and rocker arm

set.
Remove the camshaft chain from the
camshaft sprocket.
Remove the camshaft.
Camshaft Inspection
Inspect cam lobe height for damaged.
Service Limit
IN: Replacement when less than 25.29 mm
EX: Replacement when less than 25.12 mm
Inspect the camshaft bearing for looseness
or wear out. If any, replace whole set of
camshaft and bearing.
Disassembly Of Camshaft Holder

With a 5 mm bolt to screw in the cam rocker
arm shaft so that take it out.
Remove cam rocker arm.
Inspection Of Camshaft Holder

Check if the camshaft holder, cam rocker
arm and rock arm shaft for wearing out or
damage.
Camshaft
bearing
5mm bolt
rocker arm
shaft
Caution
Further check is necessary if any wear
is found on the moveable surface of
cam rocker arm.
Check if the camshaft bearing mounting
surface for wear or damage.
rocker arm
I.D.
Measure the I.D. of the camshaft holder.

Service Limit: Replace when it is above
10.10 mm
rocker arm shaft
6-5
Measure the valve rocker arm I.D.
10.100 mm
Measure the active O.D. of the valve rocker

arm shaft.
9.910 mm
Calculate the clearance between the rocker
arm shaft and the rocker arm.
0.10 mm
CYLINDER HEAD REMOVAL

Remove double seat, luggage box and front
center cover.
Remove the engine (refer to Chapter 5).
Remove the cooling fan cover.
Remove the engine shroud (L:2 bolts R:3
bolts).
Remove the camshaft.
6-6
SYM
SYM
Remove the 2 cylinder head mounting bolts
from cylinder head left side cover.
Remove cylinder head gasket and 2 dowel
pins.
Remove chain plate.
Clean up residues from the matching
surfaces of cylinder and cylinder head.
dowel pins
Caution
Do not damage the matching surfaces of
cylinder and cylinder head.
Avoid residues of gasket or foreign
materials falling into crankcase as
cleaning.
Chain plate
Cylinder head gasket
CYLINDER HEAD DISASSEMBLY

Use a valve compressor to press the valve
spring.
valve cotters
After removed valve cotters, release the

compressor and then take out spring retainer,
valve spring and valves.
Caution
I In order to avoid to loosing spring
tension, do not compress the spring too
much. Its length is based on the
installation of latch.
Special Service Tool: Valve spring compressor.
Remove valve stem guide seal.

Clean carbon deposits in combustion
chamber.
Clean residues and foreign materials on
cylinder head matching surface.
Caution
Do not damage the matching surface of
cylinder head.
6-7
SYM
CYLINDER HEAD INSPECTION

Check if spark plug and valve holes are crack.
Measure cylinder head flat with a
straightedge and flat feeler gauge.
Service limit: below 0.05mm
Valve spring free length

Measure the free length of intake and
exhaust valve springs.
Standard:
35.250 mm
The narrow pitch of the spring shall face to the

combustion chamber.
Valve stem
Check if valve stems are bend, crack or burn.
Check the operation condition of valve stem
in valve guide, and measure & record the
valve stem outer diameter.
Service Limit: IN 4.900mm
EX 4.900mm
Valve guide
Caution
Before measuring the valve guide, clean
carbon deposits with reamer.
Special Service Tool: 5.0mm valve guide
reamer
Measure and record each valve guide inner
diameters.
Service limit: 5.030mm
The difference that the inner diameter of
valve guide deducts the outer diameter of
valve stem is the clearance between the
valve stem and valve guide.
Service Limit: IN 0.08mm
EX 0.10mm
6-8
5.0mm valve guide reamer
SYM
Caution
If clearance between valve stem and
valve guide exceeded service limit, check
whether the new clearance that only
replaces new valve guide is within service
limit or not. If so, replace valve guide.
Correct it with reamer after replacement.
If clearance still exceeds service limit after
replaced valve guide, replace valve stem too.
Caution
It must correct valve seat when replacing
valve guide.
Valve guide replacement

Heat up cylinder head to 100~150 with
heated plate or toaster.
Valve guide driver

5.0mm
Caution
Do not let torch heat cylinder head
directly. Otherwise, the cylinder head
may be deformed as heating it.
Wear on a pair of glove to protect your
hands when operating.
Hold the cylinder head, and then press out old
valve guide from combustion chamber side.
Tool: Valve guide driver 5 mm
13 mm
(0.15in)
Valve guide driver

5.0mm
Caution
Check if new valve guide is deformation
after pressed it in.
When pressing in the new valve guide,
cylinder head still must be kept in
100~150 .
Adjust the valve guide driver and let valve
guide height is in 13mm.
Press in new valve guide from rocker arm side.
Tool: Valve guide driver 5 mm
Wait for the cylinder head cooling down to
room temperature, and then correct the new
valve guide with reamer.
Caution
Valve guide reamer 5.0mm
Using cutting oil when correcting valve

guide with a reamer.
Turn the reamer in same direction when
it be inserted or rotated.
Correct valve seat, and clean up all metal
residues from cylinder head.
Special tool: Valve guide reamer 5 mm
6-9
SYM
VALVE SEAT INSPECTION AND

SERVICE
Clean up all carbon deposits onto intake and
exhaust valves.
Apply with emery slightly onto valve contact
face. Grind valve seat with a rubber hose or
other manual grinding tool.
Caution
Do not let emery enter into between
valve stem and valve guide.
Clean up the emery after corrected,
and apply with red paint onto contact
faces of valve and valve seat.
Remove the valve and check its contact
face.
Valve seat
valve seat
width
Caution
width
Replace the valve with new one if valve

seat is roughness, wear out, or
incomplete contacted with valve seat.
If the valve and the valve seat still can
not be matched sealing after grinded,
replace it with new one.
Roughness
Valve seat inspection

If the valve seat is too width, narrow or rough,
correct it.
Valve seat width
Check the contact condition of valve seat.
45
Valve seat grinding

The worn valve seat has to be grinded with
valve seat chamfer cutter.
Use 45 valve seat chamfer cutter to cut any
rough or uneven surface from valve seat.
Caution
After valve guide had been replaced, it
has to be grinded with 45 valve seal
chamfer cutter to correct its seat face.
Use 32 cutter to cut a quarter upper part
out.
6-10
Old valve seat width
32
SYM
Use 60 cutter to cut a quarter lower part out.

Remove the cutter and check new valve
seat.
Old valve seat width
60
Use 45 cutter to grind the valve seat to
specified width.
1.0mm
Caution
Make sure that all roughness and
uneven faces had been grinded.
Grind valve seat again if necessary.
45
Coat the valve seat surface with red paint.
Install the valve through valve guide until the
valve contacting with valve seat, slightly
press down the valve but do not rotate it so
that a seal track will be created on contact
surface.
Contact surface too high

Old valve seat
width
32
Caution
The contact surfaces of valve and valve
seat are very important to the valve
sealing capacity.
If the contact surface too high, grind the

valve seat with 32 cutter.
Then, grind the valve seat with 45 cutter to
specified width.
If the contact surface too low, grind the valve
seat with 60 cutter.
Then, grind the valve seat with 45 cutter to
specified width.
Contact surface
too low
Old valve seat

width
60
6-11
SYM
After the valve seat grinded, coat valve seat

surface with emery and then slightly press
the grinded surface.
Clean up all emery coated onto cylinder and
valve after grinded.
CYLINDER HEAD REASSEMBLY

Lubricate valve stem with engine oil, and
then insert the valve into valve guide.
Install new valve stem oil seal.
Install valve springs and retainers.
Caution
The closed coils of valve spring should
face down to combustion chamber.
Use valve spring compressor to press valve

spring.
Install valve split locks and release the valve
compressor.
Caution
In order to avoid to loosing spring
tension, do not compress the spring too
much. Its length is based on the
installation of latch.
Special tool: valve spring compressor
Tap valve stem to make valve retainer and

valve stem sealing properly.
Caution
Place and hold cylinder head on to working
table so that can prevent from valve
damaged.
6-12
Valve cotters
Valve stem
oil seal
Valve spring
retainer
Valve spring
Valve
SYM
CYLINDER HEAD INSTALLATION
Cylinder head gasket
Lock pins
Install the lock pins and new cylinder head

gasket onto the cylinder head.
Install the camshaft chain plate.
Chain plate
Install the cylinder head.
CAMSHAFT INSTALLATION
Assemble the camshaft holder.
Install the exhaust valve rocker arm set onto
the camshaft holder showing EX mark.
Install intake valve rocker arm and rocker
arm shaft.
5mm blot
Caution
The tangent of rocker shaft of intake
valve should match with the bolt hole of
camshaft mounting seat.
With T type wrench to turn crankshaft in a
clockwise motion so that the T mark on the
flywheel aligns with the mark on crankcase.
(piston is at TDC position)
Place the TDC marks of the cam sprocket at
same level of the top-end of cylinder head.
The other single hole of the cam sprocket is
in upward. Then, install the cam chain onto
the cam sprocket.
Rocker
arm shaft
Rocker arm
Camshaft
Cam chain
6-13
Install the lock pins.
Install the camshaft holder, gasket and nut
onto the cylinder head.
Tighten the cylinder head nuts. (4 nuts)
At first, tighten the 4 nuts on the cylinder top
and then tighten the 2 bolts on the left side of
cylinder head.
Install the spark plug and tighten it.
Caution
Apply with oil onto the thread of cylinder
head bolts and tighten the bolts in
diagonally for 2-3 sequences.
Do not over tightening the bolts to avoid
the cylinder head deformation, noise
created or leaking so that effects
motorcycles performance.
SYM
pin
holder
Especial tool
VALVE CLEARANCE ADJUSTMENT

Loosen valve clearance adjustment nuts and
bolts located on valve rocker arm.
Measure and adjust valve clearance with
feeler gauge.
After valve clearance had been adjusted to
standard value, hold adjustment bolt and
then tighten the adjustment nut.
Standard Value: IN/EX 0.060.02mm
Turn the cam chain adjuster in clockwise
motion so that the adjuster is pushed out to
contact the cam chain plate tightly. Tighten
the bolt cap of the adjuster adjustment hole.
Caution
The O-ring must be installed into glove.
Replace the O-ring of the cylinder head with

new one. Install the cylinder head.
Blow-by hose
Tighten the cylinder head lock bolts.

Connect the blow-by hose onto the cylinder
head.
Tighten the 2nd air injection (AI) nut.
Install the engine onto the engine frame.
(Refer to Chapter 5)
A.I
6-14
4 bolts
SYM
CYLINDER REMOVAL .......................7-3
7. CYLINDER/PISTON
PISTON REMOVAL............................7-5
PISTON RING INSTALLATION..........7-7
PISTON INSTALLATION....................7-8
CYLINDER INSTALLATION .............. 7-8
MECHANISM DIAGRAM
0.8~1.2kgf-m
7-1
7. CYLINDER/PISTON
SYM
General Information
Both cylinder and piston service cannot be carried out when engine mounted on frame.
Specification
unit: mm
Item
Standard
Limit
39.00
0.050
Roundness
0.005
0.050
Cylindrical
0.005
0.050
Top ring
0.025~0.060
0.090
2nd ring
0.015~0.050
0.090
Top ring
0.200~0.400
0.500
2nd ring
0.250~0.400
0.650
Oil ring
0.200~0.700
38.970~38.990
0.025~0.040
0.100
13.002~13.008
13.040
12.994~13.000
12.980
0.002~0.014
0.018
13.005~13.020
13.040
ID
Bend/wrap age
Cylinder
Clearance between
piston and rings
Piston/
Piston ring
Ring-end gap
OD of piston
Clearance between piston and
cylinder
ID of piston pin hole
OD of piston pin
Clearance between piston and piston pin
ID of connecting rod small-end
TROUBLE DIAGNOSIS
Low Or Unstable Compression Pressure
Cylinder or piston ring worn out.
Compress pressure to high.
Too much carbon deposited in
combustion chamber and piston.
Smoking in Exhaust Pipe

Piston or piston ring worn out.
Piston ring installation improperly.
Cylinder or piston damage.
Knock or Noise
Cylinder or piston ring worn out.
Carbon deposits on cylinder head
top-side.
Piston pin hole and piston pin wear out.
Engine Overheat
Carbon deposits on cylinder head top
side.
7-2
SYM
CYLINDER REMOVAL
7. CYLINDER/PISTON
Cylinder
2 bolts
Remove cylinder head. (refer to chapter 6)

Remove 2 bolts and then take out the cam
chain auto-adjuster.
Remove cam chain plate.

Remove cylinder.
Remove cylinder gasket and lock pins
Clean the residues attached onto the

matching surfaces of cylinder and
crankcase.
7-3
7. CYLINDER/PISTON
SYM
Cover the holes of crankcase and cam chain

with a piece of cleaning cloth.
Clean up all residues or foreign materials
from the two matching surfaces of cylinder
and crankcase.
Caution
To soap the residues into solvent so that
the residues can be removed more easily.
INSPECTION
Check if the inner diameter of cylinder is
worn out or damaged.
In the 3 positions (top, center and bottom)
of cylinder, measure the X and Y direction
values respective in the cylinder.
Service limit:39.047mm
Calculate both the real roundness (the
difference between X and Y motion values)
and the cylindrical roundness (the
difference in the top, center or bottom
positions of X or Y motion values.). Then,
determinate by the max. value.
Service limit
Real roundness: correct or replace as
over 0.05 mm
Cylindrical roundness: correct or replace
as over 0.05 mm
Check Cylinder flat.
Service limit: correct or replace as over
0.05 mm
7-4
Exhaust side
Top
Center
Bottom
Intake side
SYM
7. CYLINDER/PISTON
PISTON REMOVAL
Plug crankcase opening with a cleaning cloth
to prevent from piston pin snap ring or other
parts falling into crankcase when
disassembling.
Hold another snap ring with pliers.
Push out the piston pin from the side that not
removed the snap ring.
Remove piston rings.

Caution
Pay attention to remove piston rings
because they are fragile.
Disassemble the piston rings.
Check if the piston rings are damaged or its
grooves are worn.
Cleaning the carbon in piston ring grooves.
Piston ring
Install the piston rings and then measure

clearance between piston ring and its
grooves.
Service Limit: Top ring: replace if over
0.09mm
2nd ring: replace if over
0.09mm
Push in
Piston
Feeler gauge
Take out the piston rings and place them

respective into cylinder below 20mm of
cylinder top. Measure each piston ring
gaps.
Feeler gauge
Caution
Push the piston rings into cylinder with
piston top-end in parallel motion.
Service Limit: Top ring: replace if over
0.50mm
2nd ring: replace if over
0.650mm
piston ring
7-5
7. CYLINDER/PISTON
Measure the outer diameter of piston pin.
Service Limit: 12.980mm
Measure the inner diameter of connecting

rod small end.
Measure the inner diameter of piston pin

hole.
Calculate clearance between piston pin and
its hole.
Measure piston outer diameter.

Caution
The measurement position is 10 mm
distance from piston bottom side, and 90
to piston pin.
Compare measured value with service limit
to calculate the clearance between piston
and cylinder.
7-6
SYM
SYM
7. CYLINDER/PISTON
PISTON RING INSTALLATION

Clean up piston top, ring groove, and piston skirt.
Install the piston ring onto piston carefully.
Place the openings of piston ring as diagram shown.
Caution
Do not damage piston and piston rings as installation.
All marks on the piston rings must be forwarded to up side.
Make sure that all piston rings can be rotated freely after installed.
Top ring
120
2nd ring
Side ring
Spacer
Oil ring
Side ring
Over 20 mm
Top groove
2nd groove
Oil groove
7-7
7. CYLINDER/PISTON
SYM
PISTON INSTALLATION
Install piston and piston pin, and place the IN
mark on the piston top side forward to intake
valve.
Install new piston pin snap ring.
IN mark
Piston pin
Caution
Do not let the opening of piston pin snap
ring align with the opening piston ring.
Place a piece of cleaning cloth between
piston skirt section and crankcase in
order to prevent snap ring from falling
into crankcase as operation.
Piston
CYLINDER INSTALLATION
Clean up all residues and foreign materials
on the matching surface of crankcase.
Pay attention to not let these residues and
foreign materials fall into crankcase.
Caution
To soap the residues into solvent so that
the residues can be removed more
easily.
Install 2 lock pins and new gasket.
Coat engine oil to inside of cylinder, piston

and piston rings.
Care to be taken when installing piston into
cylinder. Press piston rings in one by one as
installation.
Caution
Do not push piston into cylinder forcefully
because this will cause the piston and the
piston rings to be damaged.
2 bolts
Install the cam chain plate, the cylinder

gasket and lock pins.
Install cylinder head. (refer to Chapter 6)
Install the cam chain auto-adjuster. (2 bolts)
7-8
SYM
8. V-BELT DRIVING SYSTEM/KICK STARTER ARM/STARTER CLUTCH

MAINTENANCE DESCRIPTION ........8-2
LEFT CRANKCASE COVER ..............8-3
KICK STARTER ARM ........................ 8-3

DRIVING BELT................................... 8-4
SLIDING PULLEY .............................. 8-6
CLUTCH/DRIVEN PULLEY............... 8-9
MECHANISM DIAGRAM
5.0~6.0kgf-m
5.0~6.0kgf-m
3.5~4.5kgf-m
0.8~1.2kgf-m
8-1
SYM
MAINTENANCE DESCRIPTION
GENERAL INFORMATION
Driving pulley, clutch, and driven pulley can be serviced on the motorcycle.
Driving belt and driving pulley surface must be free of grease.
Specification
Item
Driving belt width
ID of sliding pulley bush
OD of roller
ID of clutch outer
Thickness of clutch pad
Free length of drive pulley
i
OD of driven pulley
ID of sliding pulley
ID: Inner Diameter
OD: Outer diameter
Unit: mm
Standard value
17.50
20.035~20.085
Limit
16.8
15.920~16.080
107.00~107.20
4.000
20.150
15.570
107.50
2.0
97.20
96.5
33.965~33.985
33.940
34.000~34.025
34.060
Torque value
Sliding pulley nut: 5.0~6.0kgf-m
Clutch outer nut: 5.0~6.0kgf-m
driving pulley nut: 3.5~4.5kgf-m
Special Service Tools

Clutch spring compressor
Bearing puller (inner type)
Clutch mounting nut wrench
Universal fixture
TROUBLE DIAGNOSIS
Engine can be started but motorcycle
can not be moved
1. Worn driving Belt
2. Worn tilt plate
3. Worn or damaged clutch lining
4. Broken driven pulley
Shudder or misfire when driving
1. Broken clutch lining
2. Worn clutch lining
8-2
Insufficient horsepower or poor high

speed performance
1. Worn driving belt
2. Insufficient spring capacity of driven
pulley
3. Worn roller
4. Driven pulley operation un-smoothly
SYM
LEFT CRANKCASE COVER
kick starter arm
air cleaner lock nut
Left crankcase cover removal

Remove air cleaner. (2 bolts)
Remove kick starter arm. (1 bolt)
Loosen vent strap on the front-left side of
cover, and then remove the vent.
Remove engine left-side cover (8 bolts).
KICK STARTER ARM

Disassembly
Remove the return spring, starter shaft.
Remove driving gear, friction spring and
washer.
Inspection
Check if starter shaft, driving gear, for wear
or damage. Replace it with new one if
necessary.
Check the return spring for spring force or
damaged. Replace it with one if poor parts
found.
Reassembly
Apply with some specified grease on the
gear, shaft.
Install the friction spring of driving gear onto
convex part of the case cover.
Install, return spring and starter shaft as
diagram shown.
Install kick starter arm temporary.
Rotate the lever and then align driving gear
with width-tooth on the starter shaft.
Install thrust washer and socket onto starter
shaft.
Installation of the left crankcase

cover
Starter spring
shaft
Friction
Starter shaft
Return spring
Driving gear
starter shaft gear
driving gear
Strap
Bolts
Install the left crankcase cover. (8 bolts)

Install front vent tube of left cover and tighten
the strap.
Install kick starter arm. (1 bolt)
Tighten the air cleaner. (2 bolts)
Kick starter arm shaft
8-3
DRIVING BELT
SYM
sliding pulley
Removal
Remove left crankcase cover.
Hold the sliding pulley with a universal fixture,
and then remove the nut and sliding pulley.
Universal fixer
Hold driving pulley with universal fixture, and

remove nut and clutch outer.
driving pulley
Caution
Using special service tools for tightening or
loosening the nut. Fixed rear wheel or rear
brake only will damage reduction gear
system.
Nut
Universal fixer
Push the driving belt into belt groove as

diagram shown so that the belt can be
loosened, and then remove.
Driving belt and clutch at same time.
Driving belt
Inspection
Check the driving belt for crack or wear.
Replace it if necessary.
Measure the width of driving belt as diagram
shown. Replace the driving belt if it exceed
maintenance limited specification.
Caution
Using the genuine parts for replacement.
The surfaces of driving belt or pulley must
be free of grease.
Clean up all grease or dirt before
installation.
8-4
Tooth
Width
SYM
Installation
Pull out the driving pulley and then insert the
driving pulley.
Sliding
driven
pulley
Caution
Pull out driving pulley and then insert the
driving belt into the driving pulley so that the
driving belt set can be installed onto sliding
pulley more easily.
starter gear
Install the starter gear.

Install the clutch set with driving belt onto the
driving shaft.
Install the sliding pulley on the other end of
belt.
Install clutch outer.
sliding pulley
clutch outer
Clutch outer
Install the clutch with universal fixture, and

then tighten nut to specified torque value.
Nut
Universal fixer
Caution
When install the driving belt, if there is a
arrow mark, then the arrow mark must
point to rotation motion. If not, the letters
on the belt must be forwarded to
assembly direction.
8-5
SLIDING PULLEY
Starter gear
SYM
driving pulley
REMOVAL
Remove left crankcase cover.
Hold driving pulley with universal fixture, and
then remove driving pulley nut.
Remove driving pulley.
nut
Remove the sliding pulley fixing nut and

remove the driving belt from the sliding
pulley.
Remove the driving belt from the sliding
pulley.
Remove the limited speed bush.
Remove the bush and remove the sliding
pulley from the crankshaft.
Crankshaft
Sliding pulley
Bush
Limited speed
bush
Remove tilt plate.

Tilt plate
Remove weight rollers from sliding pulley.
Sliding pulley
Roller
8-6
SYM
Inspection
The operation of sliding pulley is means of
the weight roller to pressing on it with
centrifuge force. And then the speed is
changed by the title plate rotation. Thus, if
weight rollers are wear out or damage, the
centrifuge force will be effected.
Check if rollers are wear out or damage.
Measure each rollers outer diameter.
Replace it if exceed the service limit.
Service limit: 15.57 mm
Weight roller
Sliding pulley
Measure the inner diameter of the sliding

pulley.
Pulley hub
Measure the inner diameter of the pulley

bush.
Replace it if exceed the service limit.
Weight roller
Assembly/Installation
Install the weight rollers.
Guide boot
Install the title plate guide boot onto the title

plate.
Install the title plate.
Tilt plate
8-7

Apply with grease 4~5 g to inside of driving
shaft hole, and install driving pulley hub.
SYM
Pulley bush
Caution
The pulley surface has to be free of
grease. Clean it with cleaning solvent.
Pulley surface
Install siding pulley assembly onto crankshaft.
Crankshaft
Sliding pulley
Pulley bush
Limited speed
bush
Driving pulley install

Press driving belt into pulley groove, and
then press down the up & down sides of the
driving belt to separate it away from the
driving pulley hub.
Caution
To press down the up & down sides of the
driving belt can avoid to pressing and
damaging the belt when installing the
driving pulley, and also can make sure that
the driving pulley can be tighten.
Install driving pulley, washer and nut.
Caution
Make sure that two sides of pulley
surfaces have to be free of grease.
Clean it with cleaning solvent.
Hold driving pulley with universal fixture.
Tighten nut to specified torque.
Install left crankcase cover.
8-8
Press down
Driving belt
SYM
CLUTCH/DRIVEN PULLEY
Special nut wrench
DISASSEMBLY
Remove driving belt and clutch/driven pulley.
Install clutch spring compressor onto the
pulley assembly, and operate the
compressor to let nut be installed more
easily.
Caution
Do not press the compressor too much.
Hold the clutch spring compressor onto

bench vise, and then remove mounting nut
with special nut wrench.
Release the clutch spring compressor and
remove clutch and spring from driven pulley.
Remove socket from driven pulley.
Socket
Remove oil seal from driven pulley.

Remove guide pin, guide pin roller, and
sliding pulley, and then remove O-ring & oil
seal seat from sliding pulley.
Sliding pulley
Guide pin
Oil seal
O-ring
Guide pin
Guide pin
roller
INSPECTION
Clutch outer
Measure the inner diameter of clutch outer
friction face. Replace the clutch outer if
exceed service limit.
Inner
diameter
Clutch outer
8-9

Clutch lining
Measure each clutch lining thickness.
Replace it if exceeds service limit.
SYM
Clutch lining
Clutch
Driven pulley spring

Measure the length of driven pulley spring.
Free length
Driven pulley
Check following items;
If both surfaces are damage or wear.
If guide pin groove is damage or wear.
Replace damaged or worn components.
Measure the outer diameter of driven surface
and the inner diameter of driven pulley.
Service limit: Outer diameter 33.94mm
Inner diameter 34.06mm
Driven pulley
Sliding disc
Driven Pulley Bearing Inspection

Check if the inner bearing oil seal is damage.
Check if needle bearing is damage or too big
clearance. Replace it if necessary.
Rotate the inside of inner bearing with fingers
to check if the bearing rotation is in smooth
and silent.
Needle bearing
Outer ball bearing
8-10
Guide pin
groove
SYM
Clutch Block Replacement

Remove snap and washer, and the remove
clutch block and spring from driving plate.
Check if spring is damage or insufficient
elasticity.
Driving plate
Spring
Snap ring
Clutch block
Check if shock absorption rubber is damage

or deformation. Replace it if necessary.
Apply with grease onto setting pins.
Shock absorption rubber
Setting pin
Apply with grease onto setting pins. But,

the clutch block should not be greased. If so,
replace it.
Install new clutch block onto setting pin and
then push to specified location.
Shock absorption rubber
Caution
Grease or lubricant will damage the
clutch block and effect the blocks
connection capacity.
Clutch block
Install the spring snap into groove with pliers.

Spring
8-11
SYM
Install snap ring and mounting plate onto

setting pin.
Snap ring
REPLACEMENT OF DRIVEN PULLEY

BEARING
Remove inner bearing.
Oil seal
Outer bearing
Caution
If the inner bearing equipped with oil
seal on one side in the driven pulley,
then remove the oil seal firstly.
If the pulley equipped with ball bearing,
it has to remove snap ring and then the
bearing.
Remove snap ring and then push bearing

forward to other side of inner bearing.
Place new bearing onto proper position and
its sealing end should be forwarded to
outside.
Apply with specified grease.
Recommended to use the KING MATE G-3.
Install the snap ring and hold the bearing.
Inner needle
bearing
Snap ring
Specified grease
Snap ring
Outer bearing
Sealing end
Install a new inner bearing.
Sealing end
Caution
Its sealing end should be forwarded to
outside as bearing installation.
Install needle bearing with hydraulic
presser. Install ball bearing by means
of hydraulic presser.
Align oil seal lip with bearing, and then install
the new oil seal (if necessary).
8-12
Inner bearing
SYM
INSTALLATION OF CLUTCH/DRIVEN
PULLEY ASSEMBLY
Install new oil seal and O-ring onto sliding
pulley. Apply with specified grease to
lubricate the inside of sliding pulley.
Oil seal
Specified
grease
O-ring
Sliding pulley
Install sliding pulley onto driven pulley.

Install guide pin and guide pin roller.
O-ring
Guide pin
Oil seal
Guide pin
Guide pin
roller
Oil socket
Install oil socket.
Install driving belt, spring and clutch into

clutch spring compressor, and press down
the assembly by turning manual lever until
mounting nut that can be installed.
Hold the compressor by bench vise and
tighten the mounting nut to specified torque
with special nut wrench.
Remove the clutch spring compressor.
Torque value: 5.0~6.0 kg-m
Install clutch/driven pulley and driving belt
onto driving shaft.
Special nut wrench
8-13
SYM
9. FINAL DRIVING MECHANISM

OPERATIONAL PRECAUTIONS .......9-2
DISASSEMBLY OF FINAL DRIVING
MECHANISM......................................9-3
INSPECTION OF FINAL DRIVING

MECHANISM...................................... 9-3
BEARING REPLACEMENT................ 9-4
RE-ASSEMBLY OF FINAL DRIVING
MECHANISM......................................9-6
MECHANISM DIAGRAM
2.6~3.0 kgf-m
2.6~3.0 kgf-m
9-1
SYM
Specification
Application gear oil: 4-stroke lubricant
Recommended gear oil: 85W-140
Oil quantity: 110 c.c. (100 c.c. when
replacing)
Torque value
Gear box cover
Gear oil drain plug
2.6~3.0 kgf-m
1.0~1.5 kgf-m
1.0~1.5 kgf-m
Tools
Inner type bearing puller
Outer type bearing puller
Gear box oil seal installer
Gear box bearing installer
TROUBLE DIAGNOSIS
Engine can be started but motorcycle
can not be moved
Damaged driving gear
Burnt out driving gear
Broken driving belt
Noise
Worn or burnt gear
Worn gear
9-2
Gear oil leaks

Excessive gear oil
Worn or damage oil seal
SYM
DISASSEMBLY OF FINAL DRIVING

MECHANISM
7 bolts
Remove the rear wheel. (refer to chapter 15)

Remove the clutch.
Drain gear oil out from gear box.
Remove gear box cover bolts (7bolts) and
then remove the gear box cover and the final
driving shaft.
Remove gasket and setting pin.
final driving shaft

Remove countershaft and gear.
Remove final driving gear and shaft.
countershaft gear
final driving gear
countershaft
driving shaft
INSPECTION OF FINAL DRIVING

MECHANISM
Check if the countershaft and the gear are
wear or damage.
final driving shaft

Check if the final driving shaft and gear are
burn, wear or damage.
final driving gear
9-3

Check bearings on the gear box cover.
Rotate each bearings inner ring with fingers.
Check if bearings can be turned in smooth
and silent, and also check if bearing outer
ring is mounted on gear box & cover tightly.
If bearing rotation is uneven, noising, or
loose bearing mounted, then replace it.
Check oil seal for wear or damage, and
replace it if necessary.
Check driving shaft and gear for wear or

damage.
SYM
bearing
final driving shaft

final driving gear
countershaft gear
countershaft
BEARING REPLACEMENT
Caution
driving shaft
Never install used bearings. Once bearing

removed, it has to be replaced with new
one.
Remove driving shaft bearing from left

crankcase using following tools;
Install new driving shaft bearing into left

crankcase.
Tool:
Press the bearing into cover with C type
hydraulic presser or bearing installer.
9-4
driving shaft bearing
SYM
Press out the driving shaft from the
crankcase.
Remove oil seal from the crankcase.
Remove the driving shaft bearing from the
gear box cover with the inner type bearing
puller.

Driving shaft
Caution
Using the bearing protector as pressing out
the driving shaft from the left crankcase.
Specified tool:
Inner type bearing puller.
Bearing protector
If the driving shaft is pulled out with its

bearing, then remove the bearing with bearing
puller and bearing protector.
Tool:
Multi-functional bearing puller
Bearing protector
Multi-functional bearing puller
driving shaft
Install a new driving shaft bearing onto
crankcase.
Then, install the driving shaft.
Specified tool:
Press the bearing in with C type hydraulic
presser or bearing installer.
final driving shaft

bearing
Install a new final driving shaft bearing onto
crankcase.
Specified tool:
Press the bearing in with C type hydraulic
presser or the bearing installer.
Apply with some grease onto the lip section
of oil seal and then install the seal.
9-5

RE-ASSEMBLY OF FINAL DRIVING
MECHANISM
SYM
countershaft
final driving shaft
Install final driving shaft and final driving gear,

countershaft, and countershaft gear.
final shaft gear

Install the setting pins(2 pins) and new gasket.
dowel pins
Apply with grease onto the oil seal lip of final
driving shaft.
Install the gear box cover and 7 bolts.
(tighten the bolts)
Torque: 2.6~3.0 kgf-m
Install the clutch/sliding driving pulley.
Install the driving pulley, belt and left
crankshaft cover.
Install the rear wheel.
7 bolts
Filling bolt
Add gear oil.

Recommended usage gear oil :SAE
85W-140
(110 cc: standard capacity)
(100 cc: when replacement)
Draining bolt
9-6
SYM
A.C.GENERATOR REMOVAL............10-2
RIGHT CRANKCASE COVER
REMOVAL .......................................... 10-3
10. A.C. GENERATOR

INSTALLATION .................................. 10-4
MOUNTED COIL SET
INSTALLATION .................................. 10-4
FLY WHEEL INSTALLATION............. 10-4
General information
Refer to chapter 5: Engine removal and installation
Refer to chapter 1: The troubleshooting and inspection of A.C. generator
Torque value:
Flywheel nut
Exhaust muffler bolt 8 mm
Oil screen cover
3.5~4.5kgf-m
3.0~3.6kgf-m
1.0~2.0kgf-m

Flywheel puller
Universal fixture
10-1
10. A.C. GENERATOR/STARTING CLUTCH
SYM
A.C. GENERATOR REMOVAL

Pulse generator
Flywheel
Cooling fan
Cooling fan
shroud
Coil
Cable guide
Cooling fan shroud
Drain out the engine oil.

Remove the exhaust muffler. (2 bolts, 2 nuts)
Remove the fan shroud. (4 bolts)
Exhaust muffler
Remove the fan. (4 bolts)
Cooling fan
Hold the flywheel with the universal fixture.

Remove the 10mm nut on the flywheel.
Special Service Tools:
Universal Fixture
10-2
Universal fixture
SYM
10. A.C. GENERATOR
Remove the flywheel with the flywheel puller.

Special service tools:
Flywheel puller
Shaft protector
Caution
Install a shaft protector on the right end of
crankshaft to avoid damaging the
crankshaft before installing the flywheel
puller.
Flywheel puller
Pulse generator connector
Remove the connectors of the A.C.

generator and pulse generator.
generator connector
Pulse generator
Cable guide
Remove the 6 bolts for the pulse generator,

the A.C. generator coil and cable guide.
Then, remove the A.C. generator assembly.
Caution
Do not damage the alternator coil.
Coil

REMOVAL
Remove the right crankcase cover. (8 bolts)
Remove setting pin and gasket.
Remove the gasket or foreign materials on
the connection surfaces of both the cover
and crankcase.
Caution
Do not damage the connection surfaces.
8 bolts
10-3
10. A.C. GENERATOR/STARTING CLUTCH
SYM

INSTALLATION
Install setting pin and new gasket on the
crankcase.
Replace the right crankshaft oil seal of the
crankcase and apply some oil onto the oil
seal lip.
Install right crankcase cover onto the right
crankcase. (8 bolts)
Torque value: 1.5~2.0kgf-m
8 bolts
Pulse generator
MOUNTED COIL SET

INSTALLATION
Install the coil set onto right crankcase
cover. (2 bolts)
Install pulse generator. (2 bolts)
Torque: 0.8~1.2kgf-m
Tie the wire harness hose onto the indent of
crankcase.
Coil
generator connector
Install A.C. generator connector and pulse

generator connector.
Pulse generator
connector
Auto by-start
connector
FLYWHEEL INSTALLATION
Make sure that there is no magnetic powder.
If so, clean up it.
Align insert on crankshaft with the flywheel
groove, and then install the flywheel.
Hold the flywheel with flywheel holder, and
tighten its nut.
Special service tool:
Universal fixture
10-4
Universal fixture
SYM
10. A.C. GENERATOR
Install the cooling fan. (4 bolts)

4 bolts
Cooling fan
Install the cooling fan shroud. (4 bolts)

Install the exhaust muffler. (2 bolts, 2 nuts)
Add some engine oil according the
specified quantity.
Cooling fan shroud
Exhaust muffler
10-5
SYM
11. CRANKCASE/CRANKSHAFT
MECHANISM DIAGRAM .............. 11-1
DISASSEMBLY OF CRANKCASE 11-3
OPERATIONAL PRECAUTIONS ... 11-2
CRANKSHAFT INSPECTION ....... 11-5
TROUBLE DIAGNOSIS................ 11-2
ASSEMBLY OF CRANKCASE ..... 11-6
MECHANISM DIAGRAM
0.7~1.1 kgf-m
1.5~2.0 kgf-m
11-1
SYM
General Information
This Section contains descriptions concerning disassembly of the crankcase so that the
crankshaft can be serviced.
Complete following operations before disassembling crankcase.
Engine
Chapter 5
Cylinder head
Chapter 6
Cylinder and piston
Chapter 7
V-belt Drive pulley
Chapter 8
AC generator/ Starting Clutch
Chapter 10
If the crankshaft bearing or timing sprocket need be replaced, then the crankshaft set have to
replaced.
Specification
Unit: mm
Item
Standard
Limit
Left, right clearance of the big end of the connecting rod
0.100~0.350
0.550
Radial clearance of the big end of the connecting rod
0.000~0.008
0.050
Below 0.030
Run-out
Torque value
Bolts for crankcase
Bolts for cylinder/cylinder head
Engine oil draining plug
Bolts for cam chain tensioner
Special Service Tools
Crankcase remover/set
Crankshaft installation puller
Outer type bearing puller
Bearing pressing tools
Oil seal pressing tools
TROUBLE DIAGNOSIS
Engine noise
Loose crankshaft bearing
Loose crankshaft pin bearing
Wear piston pin or piston pin hole
11-2
0.8~1.2 kgf-m
0.8~1.2 kgf-m
3.5~4.5 kgf-m
0.8~1.2 kgf-m
SYM
DISASSEMBLY OF CRANKCASE
1 bolt
Remove the 1 bolt from the right crankcase.
Remove the cam chain tensioner (hex socket

bolt) from the left side of crankcase.
1 hex socket bolt
Place the left side of crankcase upward,

and then install the crankcase remover/set
onto the crankcase.
Drive the screw of the crankcase
remover/set into the crankcase, and then
separate the left and the right crankcases.
Remove the cam chain.
Caution
Never pry out the connection surfaces
of crankcases as separating.
Otherwise, the connection surfaces
could be damaged and cause oil
leaking.
It have to separate the cam chain and
the drive gear before pressing out the
both left and right crankcases.
Special Service Tools:
Crankcase remover/set
11-3
Remove the crankshaft from the right
crankcase.
Caution
The left and right bearings of crankshaft
is to press-fit onto the crankshaft.
Remove gasket and dowel pins (2).

Scrape gasket residues off the crankcase
contact surface.
Caution
Do not damage contact surface of the
crankcase.
Soap the gasket residues into solvent
and the residues will be removed
easily.
Remove oil seal from the left crankcase.
11-4
SYM
SYM
CRANKSHAFT INSPECTION
Measure left and right clearance of connecting
rod big end.
Service limit: Replace when it is more
than 0.55 mm
Measure the radical clearance of the big

end at the vertical directions.
Service limit : 0.05 mm
Place the crankshaft onto a V-block and

measure run-out of the crankshaft with dial
gauge.
60 mm
Bearing Inspection
Rotate the bearing with fingers and make
sure the bearing can be rotated smoothly
and quietly.
Check if the inner ring is connected onto the
crankshaft tightly.
Replace crankshaft as a set when noise or
looseness is detected.
90 mm
clearance
clearance
11-5
SYM
ASSEMBLY OF CRANKCASE
Install cam chain into the chain hole of the
left crankcase, and then split out the cam
chain.
Caution
Do not damage the cam chain as
installing the crankshaft.
Install crankshaft into the left crankcase and

then install two dowel pins and new
crankcase gasket.
dowel pins
Install the right crankcase and tighten the

crankcase bolts (1 bolts).
Install the cam chain tensioner.

Install a new O-ring onto the mounting bolt
of the chain tensioner.
Apply some oil on the O-ring and tighten the
bolt.
Caution
The O-ring must be installed into the
bolts groove.
11-6
1 bolt
hex socket bolt
SYM
Apply with some grease onto the oil seal lip

and then install it onto the left crankcase.
Press-fit the oil seal to specified position

with the oil seal installer (25x37x6).
Special service tools: the oil seal
installer (25x37x6)
11-7
SYM
12. BODY COVER
MAINTENANCE INFORMATION........12-2
HANDLE COVER ...............................12-3
FRONT COVER..................................12-4
UNDER COVER .................................12-5
FRONT INNER BOX........................... 12-6
BODY COVER/REAR FENDER ......... 12-7

FRONT CENTER COVER.................. 12-9
LUGGAGE BOX ................................. 12-9
FLOOR PANEL .................................. 12-9
Rear carrier
Double Seat
Front handle
cover
Front cover
Fuel tank
Rear handle
cover
Right body cover
Frame number
cover
Luggage box
Battery cover
Left body cover
Rear inner
fender
Front center
cover
Inner box
Floor panel
RR. mudguard Rear fender
Front fender
Under cover
Left side cover
Front spoiler
Right side cover
12-1
12. BODY COVER
SYM
MAINTENANCE INFORMATION
Body covers disassemble sequence:
Front handle cover
Front cover
Rear handle cover
Inner box
Luggage box & Seat
Front center cover
Rear carrier
Front spoiler
Left/right body cover
Front cushion
Left/right side cover

Rear fender
Front fender
Battery cover
Rear inner fender
Floor panel
Under cover
Be careful not to damage various covers in disassembly or re-assembly operation.

Never injure hooks molded on the body covers in disassembly or re-assembly operation.
Align the buckles on the guards with slot on the covers.
Make sure that each hook is properly installed during the assembly.
Never compact forcefully or hammer the guard and the covers during assembly.
12-2
SYM
12. BODY COVER
HANDLE COVER
Removal:
Remove the left/right back mirror.
Remove 2 lower mounting screws between
the front handle cover and the rear handle
cover.
mounting screw2
Remove the mounting screws (4 screws)

between the front handle cover and the rear
handle cover.
Screws 22
Headlight connector
Remove the headlight connector.
Remove the front handle cover.

Installation
Install according to the reverse procedure of
removal.
12-3
12. BODY COVER

between the rear handle cover and the
frame.
SYM
right
left
screws2
Remove the speedometer cable.

between the rear handle cover and meter.
Remove the left/right handle switch
connectors.
Remove the rear handle cover.
speedometer
cable
Installation:
Install according to the reverse procedure
of removal.
screws4
FRONT COVER
Removal
Remove the 1 mounting bolt of front cover
from the frame.
bolt1

between the front cover and inner box.
6 screws
12-4
SYM
Remove the front turn left/right signal light
wire connectors.
12. BODY COVER

wire connectors
Remove the front cover.

Installation:
removal.
UNDER COVER
Removal
Remove the 12 mounting screws between
the left/right side cover and the floor panel.
12 screws

the left/right side cover and the frame.
12 screws
Remove the 22 mounting bolts between
the under cover and the frame.
Remove the under cover.
Installation:
removal.
22 bolts
12-5
12. BODY COVER
SYM
FRONT INNER BOX

Removal
Remove the 6 mounting screws of front
cover from the inner box.
6 screws
spoiler from the inner box.
2 screws
2 screws
spoiler from the inner box.
front spoiler
Remove the screw on the front inner box.
12-6
1 screw
SYM
12. BODY COVER

1 screw
Remove the screw on the main switch.

Remove the main switch cover.
Remove the front inner box A.

Installation
Install the inner box A and the front inner box
B according to the reverse procedure of
removal.
BODY COVER/REAR FENDER
6 bolts
Removal
Open the seat.
Remove the luggage box. (6 bolts)
Remove the rear carrier. (3 bolts)
3 bolts

the body cover and frame.
2 screws
12-7
12. BODY COVER
SYM

the body cover and the rear fender.
22 screws
12 screws

the body cover and the floor panel.
Remove the 1 mounting screw between the

body cover and front center cover.
1 screw
Remove the 2 mounting bolts of the rear

fender.
Remove the left/right body cover.
Remove the rear fender.
Installation
Install the body cover and rear fender
according to the reverse procedure of
removal.
12-8
2 bolts
SYM
12. BODY COVER
FRONT CENTER COVER

Removal
Remove the 1 mounting screw between the
body cover and the front center cover.
1 screw
Remove the 4 screws from the battery cover.

Remove the the battery cover.
Remove the front center cover.
4 screws
Installation
Install the cover according to the reverse
procedure of removal.
LUGGAGE BOX
Removal
Open the seat.
Remove the 6 bolts from the luggage box.
Remove the luggage box and the double
seat.
Remove the engine start control switch wire
connectors.
Installation
Install the luggage box according to the
reverse procedure of removal.
FLOOR PANEL
Removal
Remove the 4 bolts from the floor panel.
6 bolts
4 bolts
12-9
12. BODY COVER
SYM
4 screws
Remove the 4 screws from the battery

cover.
Remove the battery cover.
Remove the front center cover mounting

screw.
1 screw
12 screws
Remove the 12 screws between the body

cover and the floor panel.
12 screws
Remove the 12 screws between the

left/right side cover and the floor panel.
Remove the floor panel.
Installation
Install the floor panel according to the
12-10
SYM
13. BRAKE
MECHANISM DIAGRAM ................................13-1

MAINTENANCE INFORMATION ....... 13-3
TROUBLE DIAGNOSIS ..................... 13-4
HYDRAULIC BRAKE SYSTEM
INSPECTION ..................................... 13-5
BRAKE FLUID REPLACEMENT/
AIR-BLEED ........................................ 13-6
BRAKE CALIPER .............................. 13-7

BRAKE DISK ..................................... 13-8
BRAKE MASTER CYLINDER ........... 13-8
DRUM BRAKE-DRUM ....................... 13-11
BRAKE LING ..................................... 13-11
BRAKE PANEL.................................. 13-12
MECHANISM DIAGRAM
Front Disk Brake System
0.8~1.0 kgf-m
3.3~3.7 kgf-m
2.8~3.2 kgf-m
4.0~4.5 kgf-m
11.0~13.0 kgf-m
13-1
13. BRAKE
SYM
Rear Drum Brake System
0.8~1.2 kgf-m
0.8~1.2 kgf-m
13-2
SYM
13. BRAKE
MAINTENANCE INFORMATION
Precautions in Operation
Caution
Installing pad dusts may cause disorders of respiration system or cancer, therefore, never
use air hose or dry brush to clean brake parts. Use vacuum cleaner or other authorized tool
instead.
The brake caliper can be removed without removing the hydraulic system.
After the hydraulic system is removed, or the brake system is felt to be too soft, bleed the
hydraulic system.
While refilling brake fluid, care should be taken not to let the foreign material entering into
the brake system.
Do not spill brake fluid on the painted surfaces, plastic or rubber parts to avoid damage.
Check the operation of the brake system before you go.
Specifications
Item
Unit: mm
Standard
Limit
The thickness of front brake

disk
3.50
2.00
Front brake disk eccentricity
0.15
0.30
Master cylinder inner diameter
25.40
ID of front & rear brake drums
130.00
131.00
OD of front brake disk
130.00
Thickness of front disk brake

pad
As brake ling mark
Thickness of front drum brake

pad
2mm or As brake ling mark
Thickness of rear brake pad
2mm or As brake ling mark
Torque values
Bolt for front brake arm
Bolt for rear brake arm
Brake hose bolt
Bolt for brake caliper
Air-bleed valve
0.8~1.2kgf-m
0.8~1.2kgf-m
3.3~3.7kgf-m
3.1~3.5kgf-m
0.8~1.0kgf-m
13-3
13. BRAKE
SYM
TROUBLE DIAGNOSIS
DISK BRAKE
Soft brake lever
Air inside the hydraulic system
Hydraulic system leaking
Worn master piston
Worn brake pad
Poor brake caliper
Worn brake pad/disk
Low brake fluid
Blocked brake pipe
Warp/bent brake disk
Bent brake lever
Uneven brake
Dirty brake pad/disk
Poor wheel alignment
Clogged brake hose
Deformed or warped brake disk
Restricted brake hose and fittings
Hard operation of brake lever

Blocked brake system
Poor brake caliper
Blocked brake pipe
Seized/worn master cylinder piston
Bent brake lever
Brake noise
Dirty pad
Deformed brake disk
Poor brake caliper installation
Imbalance brake disk or wheel
Tight brake
Dirty brake pad/disk
Poor wheel alignment
Deformed or warped brake disk
DRUM BRAKE
Poor brake performance
Improper brake adjustment
Worn brake pad
Worn brake drum
Worn brake cam
Improper brake pad installation
Seized brake cable
Dirty brake pad
Dirty brake drum
Brake pad worn in brake cam area.
Poor contact between brake arm and
camshaft indent
13-4
Tight operation or low return speed of

brake lever
Worn/broken/crack return spring
Worn drum
Dirty brake pad
Brake seized caused from dirty brake
drum
Seized brake cable
Worn brake cam
Improper brake pad installation
Brake noise
Worn brake pad
Worn drum
Dirty brake pad
Dirty brake drum
SYM
HYDRAULIC BRAKE SYSTEM
INSPECTION
13. BRAKE
Hose connection
Inspection
Visual inspect for brake fluid leaking or
damage. Check if brake hose connection
loosen with wrench and turn the handlebar
from right to left motion or press down the
shock absorber to check if there is something
is interfered with the brake system or brake
components.
Brake disc
Operate the brake system and check the
brake pad. Check the front brake from front
side, and replace the brake pad with new one
when the brake pad wear limitation groove
reaches to the brake disk.
brake pad
wear limitation
groove
brake caliper
Park the motorcycle on a flat ground and
check its brake fluid level.
Recommended brake fluid: WELLRUN DOT 3
brake fluid
CAUTION
The fluid level will not be correct if
parking the motorcycle in title or just
parking. It has to waiting for around 3~5
minutes.
Never use faked brake fluid to prevent
from chemical reaction.
It has to apply with same brand brake
fluid to sure the brake performance.
Brake Fluid Add
Turn the handlebar to let the master cylinder
in horizontal position before removed the
master cylinder cap.
Place a rag onto painting, plastic or rubber
components when conduct brake system
maintenance.
CAUTION
Do not over the upper level when adding
brake fluid and avoid to spilling brake fluid
on painted surfaces, plastic or rubber
components to result in their damages.
lower
level
master cylinder cap
Lower level
13-5
13. BRAKE
SYM
Remove the master cylinder cap and
diaphragm.
Add good quality brake fluid and it has to add
same brand brake fluid into the master cylinder.
Clean dirty brake disk.
master
cylinder
diaphragm
CAUTION
The dirty brake pad or disc will reduce the
brake performance. The mixed
non-compatible brake fluid will reduce brake
performance. Foreign materials will block
the system causing brake performance to
be reduced or totally lost.
BRAKE FLUID REPLACEMENT/

AIR-BLEED
drain valve
Connect drain hose to drain valve.

Open the drain valve on the caliper and hold
and release the brake lever alternatively until
the old brake fluid is entirely drained out.
Close the drain valve and add specified brake
fluid into the brake master cylinder.
CAUTION
To reuse the spent brake fluid will effect
brake performance.
Connect one end of transparent hose to the
drain valve, and put the other end into a
container.
Open the drain valve around 1/4 turns, and at
the same time hold the brake lever until the
there is no air bubble in the drain hose and
also feeling resistance on the brake lever.
Close the drain valve when finishing the
brake system refilling fluid procedure, and
operate the brake lever to check whether air
bubble is in brake system or not. If brake is
still soft, please bleed the system as
described below.
1. Tightly hold the brake lever and open the
drain valve around 1/4 turns, and then close
the valve.
CAUTION
Do not release the brake lever before the
drain valve is closed.
Always check the brake fluid level when
carrying out the air bleeding procedure to
avoid air entering into the system.
2. Slowly release the brake lever, and wait for
a few seconds until it reaches its top
position.
3. Repeat the steps 1 and 2 until there is no air
bubble at the end of the hose. Tightly close
the drain valve.
4. Make sure the brake fluid is in the UPPER
level of the master cylinder, and refill the
fluid if necessary.
5. Cover the cap.
13-6
bubble
drain valve
transparent draining hose
SYM
13. BRAKE
BRAKE CALIPER
Removal
Place a container under the brake caliper,
and loosen the brake hose bolt and finally
remove the brake hoses.
bolts x 2
CAUTION
Do not spill brake fluid on painted
surfaces.
Remove two caliper bolts and the caliper.
hose bolt
Make sure the brake pad condition. Replace the
pad if the brake pad wear limitation groove
close to the brake disk.
brake pad wear

limitation groove
Brake Pad Replacement

Compress the caliper and let the brake pad out
of the caliper mounting plate. Compress the
brake pad locking spring. Remove the inner
brake pad firstly and then remove the outer
brake pad.
Compress the brake caliper at first as
installation. Install the inner brake pad firstly,
and then install the outer brake pad.
INSTALLATION
Install the brake caliper and tighten the
attaching bolts securely.
Torque: 3.3 kgf-m
CAUTION
Use M8 x 35 mm flange bolt only.
Long bolt will impair the operation of
brake disc.
Tighten the pad guide bolt.
Torque: 1.8 kgf-m
brake pad
brake mounting
plate
brake pad
piston
brake
caliper
locking spring
Use two seal washers and hose bolts to lock

the hose and brake caliper in place.
Torque: 3.5 kgf-m
Refill up the brake fluid to the reservoir and
make necessary air bleeding.
13-7
13. BRAKE
SYM
BRAKE DISK
Inspection
Visually check the brake disk for wear or
break.
Measure the thickness of the disk at several
places. Replace the disk if it has
exceeded the service limit.
Allowable limit: 2.0 mm
brake disk
micrometer
Remove the brake disk from wheel.
Check the disk for deformation and bend.
CAUTION
Do not let grease touch to the brake disc
that will cause brake performance.
Do not clean the brake pad with air gun.
Operator should wear mask & glove and
use vacuum cleaner to clean the brake
pad.
BRAKE MASTER CYLINDER

Removal
brake hose
CAUTION
Do not let foreign materials enter into the
cylinder.
bolts x2
CAUTION
The whole set of master cylinder, piston,
spring, diaphragm and circlip should be
replaced after removal.
Remove the front and rear handlebar
guards.
Remove the leads of brake lamp switch.
Drain out the brake fluid.
Remove the brake lever from the brake
master cylinder.
Remove the brake hose.
Remove the master cylinder seat and the
master cylinder.
Remove the rubber pad.
Remove the circlip.
Remove the piston and the spring.
Clean the master cylinder with
recommended brake fluid.
13-8
rubber boot
circlip
piston
rubber
washer
brake lamp
switch
spring
master
cylinder
SYM
13. BRAKE
Inspection
Check the master cylinder for damage or
scratch. Replace it if necessary.
Measure the cylinder inner diameter at several
points along both X and Y directions.
Replace the cylinder if the measured values
master cylinder
exceed allowable limit.

Dial gauge
Measure the outer diameter of the piston.
Replace the piston if its measured value
exceeds allowable limit.
Piston
Micrometer
Assembly
CAUTION
It is necessary to replace the whole set
comprising piston, spring, piston cup,
and circlip.
Make sure there is no dust on all
components before assembling.
Apply clean brake fluid to the piston cup, and
then install the cup onto the piston.
Install the larger end of the spring onto the
master cylinder.
The master cups cavity should be face inside
of master cylinder when installing the master
cup.
Install the circlip.
rubber boot
circlip
piston
rubber
washer
spring
brake lamp
switch
master
cylinder
CAUTION
Never install cup lip in the opposite
direction.
Make sure the circlip is seated
securely in the groove.
Install the rubber pad into groove properly.
13-9
13. BRAKE
SYM
INSTALLATION
Place the master cylinder onto handlebar,
and install the split ring and bolts. The
UP mark on the split ring should face
upward.
Align the split ring on the master cylinder
seat with the alignment point on the
handlebar.
Tighten the upper bolt of the seat to
specified torque value, and then tighten
lower bolt to the same specified torque
value.
master cylinder
brake
hose
bolts x 2
split ring
UP mark
sealing washer
Install the brake lever, and connect leads to
brake lamp switch.
Connect brake hoses with 2 new washes.
Tighten the brake hose bolt to the specified
torque value.
Torque value: 3.5 kgf-m
Make sure the hose is installed correctly.
CAUTION
Improper routing may damage leads, hoses
or pipes.
CAUTION
Kink of brake leads, hose or pipe may
reduce brake performance.
Add specified brake fluid and bleed the
system and conduct the air-bleeding job for
the system.
13-10
mounting
seat
hose bolt
brake hose
SYM
13. BRAKE
DRUM BRAKE-DRUM
Brake Drum
Removal
Use a vacuum cleaner and other suitable
tools to clean the brake parts to minimize
the hazard caused by the dust.
Caution
Inhaling dust may cause respiration
system disorder even cancer. Never
use an air hose or a dry brush as to
clean the brake parts.
Grease on brake pad will reduce
braking efficiency.
Front brake drum
Remove wheel. Remove brake drum from

wheel hub.
Inspection
Check the brake drum for wear and damage,
replace wheel hub if necessary
Measure the ID of hub at several points and
record the largest value.
Service limit : 131.0 mm
Caution
Remove the rust by using #120 sand
paper.
An inside micrometer must be used
when measuring ID of brake drum
because the brake drum has a friction
back plate.
Rear brake drum

Front
BRAKE PAD
Inspection
Measure the thickness of the brake pad at
three points (both ends and center).
If the thickness is less than specified, or if it is
contaminated by oil or grease, replace as a
set.
Service limit : Front 2.0 mm
Rear 2.0mm
Brake
pad
Brake pad
13-11
13. BRAKE
SYM
Removal
front brake cam
Caution
Brake pads must be replaced as a set.
brake spring
Remove brake shoes from the brake panel by

pulling out the brake pads with two hands.
Installation
Apply a thin coat of grease to the brake cam
and the anchor pin.
Hook the brake spring onto the brake cam.
Pull out the brake pads and install them onto
the brake panel. Wipe off the excessive
grease from the brake cam and the anchor pin
after installation.
Slightly grind the brake pad surfaces with
sand-paper to clean the surfaces.
anchor pin
rear
brake shoes
brake cam
anchor
pin
Caution
Braking efficiency will be reduced if
brake pad is contaminated by oil or
grease.
BRAKE PANEL
Removal
Remove the brake arm bolt and then
remove the brake arm, wear indicator,
brake return spring and brake cam as well
as the oil seal from the brake panel.
brake spring
brake shoes
Brake cam Brake arm
Front
Wear indicator
Return
spring
Bolt
Rear
Return spring
13-12
Wear indicator
SYM
Installation
FRONT BRAKE PANEL
Apply a thin cost of grease onto the brake
cam shaft.
Install the brake cam.
Apply a thin cost of grease onto the oil seal
lip and then install the oil seal onto the
brake cam shaft. Finally, install it on the
brake panel.
Align the end-part of the brake return spring
with the hole of brake panel.
Align both the inner gear of wear indicator
and the mark on the brake arm with the
indent gear of brake cam, and then install it.
Tighten the bolts and nuts to specified
torque.
REAR BRAKE PANEL
Apply a thin cost of grease between the oil
seals on the brake cam shaft.
Install the brake cam.
Align the mark on the brake arm with the
inner gear of the brake cam.
Tighten the bolts and nuts to specified
torque.
Hook on the return spring.
13. BRAKE
Return spring
Front
Wear
indicator
Oil seal
Brake cam
Brake arm
Rear
Return spring
Wear indicator
Brake arm
13-13
SYM
14. STEERING/FRONT WHEEL/FRONT SHOCK ABSORBER

STEERING HANDLE.......................... 14-3
FRONT WHEEL ................................. 14-4

FRONT SHOCK ABSORBER............. 14-8
FRONT FORK/STEERING COLUMN 14-8
MECHANISM DIAGRAM
4.0~5.0kgf-m
1.0~2.0kgf-m
0.2~0.3kgf-m
3.1~3.5kgf-m
2.4~3.0kgf-m
11.0~13.0kgf-m
14-1
SYM
General Information
Before remove front wheel, use a jack to lift the body until front wheel free of ground, and
take care not to rotate body in reverse.
Be careful not to allow oil or grease get on brake drum or linings.
Torque values
Front wheel axle
Steering handlebar nut
Steering column top cone sliding ring
Steering column lock nut
Speedometer cable nut
Front shock absorber: Upper nut
5.0~7.0kgf-m
4.0~5.0kgf-m
0.2~0.3kgf-m
1.0~2.0kgf-m
0.15~0.3kgf-m
2.4~3.0kgf-m
Tools
Steering column wrench
Bearing remover
Inner type bearing remover
Attachment, 3235 mm
Attachment, 4247 mm
Steering column nut wrench
Steering column top cone ring nut wrench
TROUBLE DIAGNOSIS
Hard steering stem
Over tightening of steering stem lock nut
Broken steering stem steel ball and cone
bearing seat
Insufficient tire pressure
Steering stem off center
Uneven left/right cushion
Bend fork
Bent front wheel/tire offset
14-2
Front wheel wobbling

Deformed rim
Front wheel bearing loose
Faulty tire
Wheel axle nut tightened improperly
Soft front suspension
Weak fork springs
Oil leakage of the shock absorber seal
Front suspension noise
Cushion cover friction noise
Cushion bolts loose
SYM
STEERING HANDLE
REMOVAL
Remove handle front & rear covers and the
front cover (refer to chapter 12).
Acceleration
handlebar seat
screw
Brake lever
screw
Brake lever nut
Master cylinder
Remove the 2 bolts of the brake master

cylinder, and then take out the master
cylinder and the split ring.
Caution
Seat
Split
ring
Do not operate the front brake lever to avoid

to pressing out the brake lining when
removing the master cylinder.
Bolts x 2
Remove acceleration handlebar screw and

then remove the handlebar, acceleration
cable, and handlebar cover & seat.
Screw
Remove the rear brake lever nut and screw,

then take out the rear brake cable.
Remove the brake lever seat bolt, and then
remove the seat.
Brake lever seat bolt
Brake lever nut
Brake lever screw
Brake cable
14-3

With a wrench to hold the handlebar bolt and
then remove the nut.
Take out the handlebar after removed the
bolt.
SYM
Bolt
Nut
Installation
Install the handlebar according to the
Apply with some grease onto the handlebar
moving parts when installing the acceleration
handlebar seat, acceleration handlebar, and
acceleration cable.
FRONT WHEEL
Removal
Support body bottom and lift front wheel free
of ground.
Remove the bolts, and disconnect
speedometer cable from the gear box.
Speedometer cable
Remove the wheel axle nut and pull out the

axle. Then, remove the front wheel.
Caution
Do not operate the front brake lever to avoid
to pressing out the brake lining when
removing the master cylinder.
Wheel axle nut
14-4
SYM
Inspection
Wheel axle
Set the axle in V-blocks and measure the
run-out.
Service limit: 0.2 mm.
Wheel axle
Wheel Rim
Place the wheel onto a rotated bracket.
Turn the wheel with hand and measure its
wobble value with a dial gauge.
Service limit:
Radial : 2.0 mm
Axial
: 2.0 mm
Disassembly
Remove 3 hex socket bolts and brake disc.
Remove the left axle ring and dust seal.

Remove the dust seal on the right side of
speedometer gear.
Remove the bearing with the inner type
bearing remover.
Take out the bearing spacer and then
remove the other bearing.
Tool:
Inner type bearing remover
Speedometer gear dust seal
Bearing spacer
Bearing
Bearing
Dust seal
Wheel side collar
14-5
SYM
Bearing Inspection
Turn the inner race of bearing with fingers.
The bearing should be turn smoothly. Also
check if the outer collar is tightly connected
to the wheel hub.
If the bearing do not turn smoothly, or if they
are too loose in the races, or damaged, then,
remove and replace the bearings with new
ones.
Caution
The bearing must be replaced in pair.
Clearance
Installation
Install the bearing according to the reverse
procedure of removal.
Apply some grease into the bearing seat of
the wheel hub.
Install the left bearing onto the seat.
Install the bearing spacer and then install
the right bearing onto the seat.
Clearance
Caution
Do not install used bearing and
replace the bearing once it has been
removed.
Do not the bearing in tile motion when
installing.
Tool:
C-type compressor or bearing compressor.
This two example will to louse the bearing.
Speedometer gear dust seal
Apply with some grease inside of the dust

bearing.
Install the dust seal and the front wheel side
collar.
Apply with some grease on both side of the
speedometer gear oil seal, and then install
the seal.
Bearing spacer
Bearing
Bearing
Dust seal
Wheel side collar
14-6
SYM
Installation
Align the flange part on the speedometer
gear with the slot of wheel hub, and then
install the brake disc or speedometer gear
box.
Caution
Contaminated brake lining will reduce
brake performance so the brake lining,
brake disc must be free of grease.
Stopper
Place the front wheel between the front

shock absorbers.
Align the flange part on the speedometer

gear with the slot of shock absorber stopper.
Gear box flange part
Install the front wheel axle from right shock

absorber side.
Install the wheel axle nut, and tighten it to
specified torque value.
Connect the speedometer cable to the
speedometer gear box.
Wheel axle nut
Speedometer cable
14-7
SYM
FRONT SHOCK ABSORBER

Removal
Remove the front fender, front lower spoiler,
front guard, and front wheel as well as front
brake components.
Remove the brake fluid hose clipper or cable
guide on the left shock absorber. (bolt x 1)
As for disc brake, remove the cable guide on
the right shock absorber. (bolt x 1)
Brake fluid
hose clipper
Remove the top connection bolt of the right

shock absorber. (bolt x 4)
Remove the shock absorber from the front
fork.
Bolts
Shock absorbers
Installation
Install the shock absorbers according to the
Align the shock absorber top-edge with the
top-end level of the front fork when installing
the front shock absorber onto the front fork.
Then, tighten the nut.
FRONT FORK/STEERING COLUMN

Removal
Firstly, remove the handlebar, front wheel,
front brake set, and front shock absorbers.
Remove the steering column nut.
Remove the top cone ring, and then remove
the steering column.
Steering column nut
Caution
Place the steering column bearing balls
into a parts container to avoid to
missing or shortage.
14-8
Top cone race
SYM
With a plastic hammer to tap the steering

column slightly, and then remove the top ball
bearing seat.
Remove the lower-end cone bearing seat on
the frame with a punch.
Caution
Do not damage the frame and the
steering column.
Installation
Install a new top-cone bearing seat onto the
top of steering column.
And then, push the lower-cone bearing seat
from bottom until to locking position.
Caution
Lower all bearing seat
Steering column nut
Balls
Lower cone-race
Do not let the ball bearing in title motion

as installation.
Top cone-race
Balls
Apply with some grease onto the top &

bottom bearing balls, and then install the
balls into bearing seat.
Press in a new lower cone-race onto the
steering column, and lubricate it with grease.
Install the steering column.
Lubricate the top-cone race with grease.
Drive the cone-race into the steering column
until contact with the top bearing seat no
clearance. Note, return 1/2 turn and then
tighten the top cone race to specified torque.
(tighten the race around 1/4~3/8 turn more.)
Caution
Do not tighten the top cone race too
tight to prevent from damage the ball
bearing seat when tightening the top
cone race.
Install the steering column nut and lock the
top cone race. Then, tighten the nut.
Install the bearing seat according to the
Top ball bearing seat.
Steering column nut

Return 1/2 turn
Locking to
1/4~3/8 turn
Top cone-race
Steering column nut
Caution
Check the steering column if it can be
turned freely and no clearance in
vertical motion.
Top cone-race
14-9
SYM
15. REAR WHEEL/REAR SHOCK ABSORBER
MECHANISM DIAGRAM.................... 15-1

PRECAUTIONS IN OPERATION....... 15-2
TROUBLE DIAGNOSIS ..................... 15-2
EXHAUST MUFFLER......................... 15-3

REAR WHEEL.................................... 15-3
REAR SHOCK ABSORBER ............... 15-4
MECHANISM DIAGRAM
3.5~4.5kgf-m
2.4~3.0kgf-m
0.8~1.2kgf-m
1.0~1.4kgf-m
3.0~3.6kgf-m
11.0~13.0kgf-m
15-1
SYM
General Information
As for the wheel removal, service, and installation procedures, please refer to the service
manual of high speed tire.
Specification
Items
Wheel wobbling
Unit: mm
Limit
2.0
Radial
Standard
-
Axial
2.0
4.0
2.0
Thickness of rear brake lining

Torque values:
Rear axle nut
Rear shock absorber upper mount bolt
Rear shock absorber lower mount bolt
Exhaust muffler connection nut
Exhaust muffler connection bolt
11.0~13.0kgf-m
3.5~4.5kgf-m
2.4~3.0kgf-m
1.0~1.4kgf-m
3.0~3.6kgf-m
TROUBLE DIAGNOSIS
Rear wheel wobbling
bend wheel rim
poor tire
loosen wheel shaft
Shock absorber too soft
insufficient shock
absorber spring force
15-2
Braking Noise
worn brake lining
brake drum deformation
improperly brake panel
installation
unparalleled brake drum
or wheel unparallel.
Poor brake performance

Poor brake adjustment
contaminated brake
lining
worn brake lining
greased brake drum
contaminated and
seized brake cable
improperly installation of
brake cable
SYM
EXHAUST MUFFLER
Removal
Remove the front-end nut of the exhaust
muffler. (nuts x 2)
Remove the bolts. (bolts x 2)
Remove the exhaust muffler.
Exhaust muffler
Installation
Install the exhaust muffler according to the
Caution
Replace the exhaust muffler gasket if it is
broken or deformed.
Nuts x 2
Bolts x 2
Torque value:
Exhaust muffler connection bolt:
3.0~3.6kgf-m
Exhaust muffler connection nut:
1.0~1.4kgf-m
REAR WHEEL
Inspection
Measure wheel rim wobbling.
Service limit:
Radial: 2.0mm
Axial: 2.0mm
If the wheel rim wobbling out of the
specification, except resulted from the
wheel rim deformation, it might be loosen or
worn final driving shaft bearing or bend,
deformed driving shaft.
Removal
Remove the right cover.(screws x 4)
Remove the battery. (bolts x 2)
Remove the battery cover assembly. (bolts
x2, nuts x 2)
Remove the rear wheel. (wheel axle nut x1)
15-3

REAR SHOCK ABSORBER
Removal
Remove the left & right covers. (screws x 8)
Remove the luggage box. (bolts x 4, nuts x 2,
screw x 1)
Remove the rear carrier. (bolts x 3)
Remove the body cover (bolts x2)
Remove the air cleaner bolts (bolts x2)
Remove the lower nut of the rear shock
absorber (bolt x 1)
Remove the upper nut of the rear shock
absorber (bolt x 1)
Remove the rear shock absorber.
lower mount bolt
Installation
Install the rear shock absorber according to
the reverse procedure of removal.
Caution
The rear shock absorber has to be replaced
with one set and can not be replaced by
unauthorized persons. Otherwise, it might
damage the rubber bushing and
construction.
Torque values
Rear shock absorber lower mount bolt:
2.4~3.0 kgf-m
Rear shock absorber upper mount bolt:
3.5~4.5 kgf-m
15-4
upper mount bolt
SYM
SYM
16. ELECTRICAL EQUIPMENT

SPECIFICATION ................................16-3
CHARGING SYSTEM.........................16-5
IGNITION SYSTEM ............................16-11
MECHANISM DIAGRAM
STARTING SYSTEM ..........................16-14

METER ...............................................16-15
LIGHTS/BULBS ..................................16-17
MAIN SWITCH/HORN ........................16-19
FUEL UNIT .........................................16-22
High & low beam/passing

/turn signal light/Horn
Front/Rear stop
switch
Main switch
Winker relay
Battery/ fuse box

/C.D.I
REG.REC/Horn/
/Resistor
Starting/headlight
switch
Engine start
control switch
Spark plug
Fuel unit
Starter magnetic
switch
Auto by-star
Ignition coil
Alternator
16-1
SYM
Charging System
When remove the battery, the disconnection sequence of cable terminals shall be strictly observed.
(First disconnect the negative cable terminal, next, the positive cable terminal.)
MF (Maintenance Free) battery does not need to check, add electrolyte or distilled water.
Battery must be taken out from scooter when charging the battery. But do not open the battery caps.
Do not quick charge the battery unless in emergency.
A voltmeter must be used when checking battery charging condition.
Battery can be charged or discharged alternately. To set a discharged battery idle for a prolonged
period will shorten its service life and reduce its capacity. Usually, batterys capacity will reduce after
1~2 years. After low capacity battery was charged, its voltage will increase. If it connects to an
additional load, the voltage will reduce suddenly, and then go up again.
Over-charged battery. Usually, the over-charged battery can be seen externally. If a short circuit
occurred inside the battery, there will be no voltage on the terminals of battery if voltage regulator does
not operate. Then, the batterys voltage will be too high that may reduce batterys life.
The battery will be self-discharged if it was set idle for a long time. An idle battery must be charged
about every 2months.
A new battery filled with electrolyte will generate a voltage after filled out electrolyte. The voltage
should be in 12.5V or more after 10 minutes. When electrolyte is not enough, the battery must be filled
with electrolyte and then charged to prolong the batterys life-span.
Please check electrical device according to the procedure of diagnosis chart.
Do not disconnect and connect the connector of electrical devices when current is passing these
devices because this will generate high voltage and the electrical components in the voltage-current
regulator will be damaged. The ignition switch must be turned OFF before performing any work.
Please do not replace with traditional type battery as replacement.
Please refer to the removal instruction when removing the alternator and the pulse generator.
Ignition System
Please follow the procedure of trouble diagnosis chart to check ignition system.
The ignition system equipped with a auto-advanced timing device in CDI unit. Thus, ignition timing
need not to be adjusted. In case of incorrect ignition timing occurred, check the CDI unit or alternator
system. It has to check the ignition timing with the ignition timing light if replaced these components.
Do not hang or impact the CDI unit of ignition system because the major faulty of CDI unit is caused by
impact. Therefore, take care when disassembling.
Most of ignition system problems were resulted from poor connecting connector. Please check the
connectors first when servicing.
Make sure that the heat range of spark plug is suitable. Improper spark plug is the main cause of poor
engine operation or combustion.
Inspection procedures in this manual are based on Max. voltage. This manual also contains methods
of how to check ignition coil resistance and component operation.
Please follow the continuity chart to check ignition switch.
Starting System
Starting motor can be removed directly from engine.
Please refer to chapter 10 for starting clutch removal procedures.
16-2
SYM
Specification
Charging System
Items
Specification
Capacity
Battery
Under charged
12.3V
Charging rate
Voltage
(20)
Alternator
Full charged
12V YTX7A-BS (12V 6AH)

STD:0.6A/5~10hrs, emergency charging:
6A/0.5hrs
13.1V
Capacity
12V / 6.2A
Lighting coil resistance (20)
Between yellow-green: 0.80.1
Charging coil resistance (20)
Between white-green: 0.60.1
Leaking current
Less 1mA
RPM for starting charging
2100rpm(headlight ON)
Voltage controlled by regulator

Resistor
14.50.5 V
Resistance (20) 5W5
4.5~5.5
Resistance (20) 30W7.5
7.0~8.0
Ignition System
Item
Specification
Standard
Hot type
Cold type
Spark plug gap
Primary
Spark plug
Ignition coil resistance

(20)
Secondary
F Mark
Ignition timing
Without plug cap : 3.110%K

Timing advanced Before TDC 28 / 4000 rpm

character
Pulse generator resistance (20)

Ignition coil-primary max. voltage
Pulse generator voltage
Starting System
Item
Starting motor
TORCH A7RC
TORCH A8RC
TORCH A6RC
0.6~0.7 mm
0.2110%
With plug cap : 7.610%K
50~200
95~400 V
1.7 V above
Specification
type
capacity
DC TYPE
0.5 KW
16-3
SYM
TROUBLE DIAGNOSIS
Charging System
Ignition System
No power supply
No spark produced by spark plug

The spark plug is out of work
The cable is poorly connected, open or
short-circuited
- Between alternator and C.D.I.
- Between CDI and ignition coil.
- Between CDI and main switch
Poor main switch
Poor C.D.I.
alternator is out of work
Dead battery
Disconnect battery cable
Fuse burned out
Faulty ignition switch
Low voltage
Weak battery
Loose battery connection
Charging system failure
Voltage-current regulator failure
Intermittent power supply

Loosen wire connector in charging system
Loose battery cables
Loose charging system connection
Loose connection in lighting system
Charging system failure
burn Fuse
Loose, broken or shorted wire or wire
connection
Faulty voltage-current regulator
Faulty alternator
Starting System
Starter motor does not work
The fuse is blown
The battery is not fully charge
Poor main switch
Poor starter switch
The front and rear brake switches do not
operate correctly
Starter magnetic switch is out of work
The ignition coil is poorly connected, open or
short-circuited
The starter motor is out of work
16-4
Engine does not crank smoothly

Primary coil circuit
- Poor ignition coil
- Poor connection of cable and connectors
- Poor main switch
Secondary coil circuit
- Poor ignition coil
- Poor spark plug
- Poor high-tension cable
- Current leakage in the spark plug cap
- Poor alternator
- Improper installation of the pulse sensor
- Poor C.D.I.
Weak starter motor

Poor charging system
The battery is not fully charged
Poor connection in the windings
The motor gear is jammed by foreign material
Starter motor is working, but engine does

not crank
Poor starter motor pinion
Poor starter clutch
The starter motor run in reverse direction
Poor battery
SYM
CHARGING SYSTEM
Charging wire diagram
green
white
fuse(10A)
red
yellow
alternator
REG.REC.
red
green
green
BATTERY
12V 6AH
green/black
Auto
by-starter
5W
5
Current Leakage Inspection

Turn the main switch to OFF position, and
remove the negative cable terminal (-) from
the battery.
Connect an ammeter between the negative
cable terminal and the battery negative
terminal (as shown on left diagram).
Caution
In the current leakage test, set the current
range at larger scale, then gradually
decrease to the lower scale as the test
process goes to avoid possible damage to
the ammeter and the fuse.
Do not turn the main switch to ON
position during test.
Battery(-) terminal
ground
wire
If the leaked current exceeds the specified value,

it may indicate a short circuit.
Allowable current leakage: Less than 1 mA.
Disconnect each cable one by one and take
measurement of the current of each cable to
locate the short circuit.
16-5
SYM
Battery
Removal
Remove the 4 screws on the battery cover.
(Screws x 4).
CAUTION
Electrolyte (diluted sulfuric acid) is very
toxic. Once it spreading on clothes, skin,
or eyes, it will cause burned or blind. In
case of being spread, flush with great
quantity of water immediately, and then
send to hospital.
When clothes is spread by electrolyte, it
will contact with skin. So, it must flush
with great quantity water to take off the
clothes.
4 screws
positive (+)
Battery
cover
negative (-)
Remove the battery cover.
Disconnect the negative (-) cable from the

battery first, then the positive (+) cable.
Remove the battery.
fuse
Install the battery in reverse order of

removal.
CAUTION
To prevent form circuit short, connect
positive(+) terminal at first, and next
negative (-) terminal.
16-6
C.D.I.
SYM
Voltage Check
With a digital voltage meter or multi-meter to
measure battery voltage.
Voltage:
Fully charged: 13.0 13.2V (at 20)
Undercharged: Below 12.3 V (at 20)
CHARGING
Connect the Charger positive (+) to the
battery positive (+) terminal.
Connect the Charger negative (-) to the
battery negative (-) terminal.
Charging
current
Charging time
Standard
Max.
0.6A
6.0A
5~10H
1H
Warning
Strictly keep flames away from a charging
battery.
The charging ON/ OFF is controlled by
the chargers switch. Do not control the
charging by battery jump wires.
Turn the chargers switch OFF at first
before or after charging to prevent from
sparks created on the connectors and
explosion.
To charge a battery must be based on the
batterys ampere-hour showed on label.
CAUTION
Quick charge a battery should be used
only in an emergency.
Make sure the current and charging time
of above description.
The battery will be damaged by too much
current or too rush charging.
When finishing charge, it is necessary to
measure voltage after 30 minutes.
After installing the battery, coat the terminals
with clean grease.
16-7

Charging Voltage/Current
Inspection
SYM
digital voltmeter
ammeter
Caution
Before conducting the inspection, be sure
that the battery is fully charged. Use a
fully charged battery having a voltage
larger than 13.0 V. If undercharged, the
current changes dramatically.
While starting the engine, the starter
motor draws large amount of current from
the battery. Thus, do not start the engine
with battery.
After the engine is warmed up, replace
original battery with a fully charged battery.
Connect a digital voltmeter to the battery
terminals.
Connect an ammeter between both ends of
the main fuse.
Caution
When the probe is reversibly connected, use
a voltmeter having an indication that the
current flows from the positive or the
negative direction and the measurement
should be at zero, ammeter at one direction
only.
Caution
Do not use short-circuit cable.
It is possible to measure the current by
connecting an ammeter between the
battery positive terminal and the cable
position terminal, however, while the
starter motor is activated, the surge
current of the motor draws from the
battery may damage the ammeter. Use
the kick lever to start the engine.
The main switch shall be turned to OFF
position during the process of inspection.
Never tamper with the ammeter and the
cable while there is current flowing
through. It may damage the ammeter.
16-8
Fuse ends
Connect a tachometer.
Turn on the headlight to high beam and start the
engine.
Accelerate the engine gradually to the specified
revolution per minute and measure the charging
voltage/current.
Specified Charging Current:
(headlight OFF) 0.6 A or more/2500rpm
1.2 A or more / 6000 rpm
(headlight ON)
0.4 A or more/2500rpm
1.0 A or more / 6000 rpm
Control Charging Voltage:
14.0+/0.5 V / 2000 rpm
Caution
To replace the old battery, use a new battery
with the same current and voltage.
The following problems are related to the
charging system, follow the instructions provided
in the checking list to correct it if any one of the
problems takes place.
(1) The charging voltage can not exceed the
voltage between two battery terminals and
the charging current is in the discharging
direction.
(2) The charging voltage and current are too
much higher than the standard values.
The following problems are not related to the
charging system; correct it if any by following
steps indicate in the checking list.
(1) The standard charging voltage and current
can only reach when the revolution of the
engine exceeds the specified rpm.
Bulbs used exceed their rate and
consume too much power.
The replacement battery is aged and
does not have enough capacity.
(2) The charging voltage is normal, but the
current is not.
The replacement battery is aged and
does not have enough capacity.
Battery used do not have enough
electricity or is over charged.
The fuse of the ammeter is blown.
The ammeter is improperly connected.
(3) The charging current is normal, but the
voltage is not.
The fuse of the voltmeter is blown.
SYM
VOLTAGE REGULATOR INSPECTION
REG.REC

Remove the front cover mounting
screw(screws x 1)and remove the headlight
wiring connector.
Disconnect the 4P connector on the diode,
and check the continuity between main wire
terminals according to following method.
Main wire circuit inspection
Item (wire color)
Judgment
Check voltage between
Battery voltage
battery terminal (red) and
ground (green).
Check continuity between
Continuity
ground(green) and frame.
Check illumination wire
(yellow) to ground.
(disconnect the connector of
Continuity &
the resistors pin and
resistance
automatic by-starter pin.
Illumination switch is in OFF)
Check charging coil (white) to Continuity &
ground)
resistance
If the measured value is abnormal, check the
abnormal wire circuit. If components are
good, it could be a poor wire circuit.
If all items are in good condition, then
replace the voltage regulator.
If main wire circuit check is in normal and
there is no loose in the pins of voltage
regulator connector, then measure the
resistance between the connector of voltage
regulator.
Voltage Regulator Check
Unit:
Multi-meter(+)
Red White Yellow Green
(R)
(W)
(Y)
(G)
Multi-meter
Red (R)
White (W)
Yellow (Y)
0.04~0.06
0.04~0.06
160~180
160~180
REG.REC
160~180 160~180
Green (G)
If the resistance values are abnormal among
the pins, replace the voltage regulator.
Caution
Do not touch the probe of multi-meter by
fingers, then the resistance values will be
incorrect because there is some resistance
existence in human body.
To use the multi-meter recommended by
SYM. Otherwise, the measured resistance
might be different.
White
RED
Green
Yellow
16-9

Alternator charging coil
Caution
The check of alternator charging coil and
illumination coil can be done when the
alternator is mounted on engine.
Check
Remove the 3P connector of the alternator.
Measure the resistance between the white
wire on the alternator and frame ground with
a multi-meter.
Standard: 0.60.1 (20)
Replace the alternator charging coil if the
measured value exceeds standard.
SYM
Ignition
connector
light coil
connector
Pulse generator
connector
Auto by-starter
Charging coil
connector
Alternator lighting coil

Check
Remove the 3P connector of the alternator.
Measure the resistance between the yellow
wire on the alternator and frame ground by
multi-meter.
Standard: 0.80.1 (20)
Replace the alternator lighting coil if the

measured value exceeds standard.
Resistor check

Measure the resistance between the resistor
wire (green/black) and frame ground.
Standard: 5/5W: 4.5~5.5(green/black)
Standard: 7.5/30W: 7.0~8.0(pink)
16-10
resistors
SYM
IGNITION SYSTEM
Ignition System Circuit
green
green
Black
Pluser
Blue /yellow
Black/ yellow
spark plug
Engine start control switch
Blue/yellow
green
Blue/yellow
black/yellow
Black
green
C.D.I. unit
green
Ignition coil
CDI UNIT
Removal
Remove the right body cover, then the C.D.I.
unit can be removed from the frame.
CDI UNIT
Check
Disconnect the connector from the CDI unit.
Make the following inspection at each terminal of the harness side connector.
ITEM
Pulse Generator
Primary
Ignition
Coil
Secondary
Measure at:
Standard (at 20C)
Blue/Yellow-green
50 ~200
Black/yellow-green
0.2110%
Green-high voltage cable -w/o cap

Green-high voltage cable - w/ cap
3~5K
7~12K
16-11

Ignition coil
Removal
Remove the luggage box, center cover.
Remove spark plug cap.
Remove the primary coil wire of ignition coil.
Remove the fix bolts for the ignition coil, and
remove the ignition coil.
Install the ignition coil in reverse order of
removal.
Ignition coil
Caution
Install primary coil with black/yellow lead
connected to black connector and green lead
connected to green connector.
Spark plug confirmation
Remove the spark plug and install a good
plug into plug cap, and then ground it to
engine ground.
Make sure its spark condition. If it is in not
good or burnt spark plug, replace the spark
plug with new one.
Caution
Make sure each wire connection is correct,
and test as required. Even the wire
connection is in correct, sometimes, it
might not be tested occurred.
Connect the high voltage shunt with a
multi-meter or input a resistor in the 10M
100V of voltage meter.
Connect ignition coil wires, and connect a
shunt between primary terminal (black/yellow
and green) and frame ground.
Press the starting motor button, or starting
lever to test the max. primary voltage of
ignition coil.
Connection: connect (+) terminal to green
side, and (-) to black/yellow side.
Min. voltage: Above 95 V.
Caution
Do not touch metal parts on the test probe
with fingers to avoid electric shock.
Primary coil check
Disconnect the primary coil connector and
check the resistance between primary coil
terminals.
Standard: 0.2110%(at 20)
Primary coil is good if resistance within
standard.
Primary coil is broken if resistance is infinite.
Replace the coil.
16-12
black/yellow
green
high voltage shunt
SYM
Secondary coil
Attached the spark plug cap, measure the

resistance between plug cap side and green
terminal.
Standard value: 7-12 k(20)
Remove the spark plug cap, measure the
resistance between plug cap side and green
terminal.
Standard value: 3-5 k(20)
Secondary coil is good if resistance within
standard.
Secondary coil is broken if resistance is
infinite. If the spark plug cap attached and
the measured value is exceed standard value,
it means the spark plug cap is in not good.
Ignition coil
Replacement
Remove the ignition coil bolt to replace the
ignition coil if necessary.
Pulse generator
Caution
Checking pulse generator can be done on
engine. But, the spark plug must be
installed onto the cylinder head, and
cylinder compression pressure must be in
normal condition.
Check
Remove body cover.
Remove the pulse generator connector.
Measure the resistance between blue/yellow
terminal on engine side and frame ground.
Standard: 14020(20)
Replace the alternator if the measured value
exceeds standard value.
16-13

STARTING SYSTEM
Starting Circuit
Starter magnetic switch inspection

Turn main switch to "on", and operate the
brake lever. Then press starting button to
check if there a click sound. It is normal if
there is a click sound.

Disconnect the battery negative (-) terminal.
Remove the battery positive (+) connection
and starting motor wires from the starter
magnetic switch large pin.
Remove the power control connector of the
Starter magnetic switch.
Connect a Ohmmeter between the Starter
magnetic switch large pins.
Connect the green/yellow wire to battery
positive (+) terminal, and yellow/red to
battery negative (-) terminal.
Check the continuity between the Starter
magnetic switch large pins. If it is not
continuity, then replace the starter magnetic
switch.
16-14
SYM
Starting Motor Removal
Bolts x2
Remove the right side cover. (screws x3)

Firstly, remove the battery negative (-)
terminal, and then remove the positive (+)
terminal.
Remove the starting motor power wire.
Remove the starting motor mounting bolts
and motor.
Starting Motor Installation
Install the motor in reverse order of removal.
METER
Removal
Meter
speedometer cable
Remove the speedometer cable.
Meter connector
Remove the power connector of the meter.
16-15

Remove the rear handle cover.
Remove the meter mounting screws.
Take out the meter.
Speedometer
Turn Left Signal

Indicator
Odometer
High Beam Indicator

Turn Right
Signal Indicator
Fuel meter
Caution
Do not wipe the meter or headlight with organic solvent such as gasoline to prevent from
damage these components.
Installation
Install the meter in reverse order of removal.
16-16
SYM
LIGHT/BULBS
Headlight Bulb Replacement
Remove the left/right back mirror.
Disconnect the headlight wire connector.
Press down the bulb spring locker and then
remove the locker with turning it left motion.
Remove the bulb.
Replace the bulb with new one if necessary.
(12V 35W/35W)
Caution
Do not touch the bulb surface with fingers
because the bulb will create hot-spot so
that let it be burnt. It has to be package
with cloth or wear glove as installing.
Wipe the bulb with cloth to prevent from
damaged if the bulb be touched by hands.
Install the bulb in reverse order of removal.
Turn the main switch ON/OFF to check if the
bulb has been installed properly after
installation.
Please conduct the headlight beam

adjustment job if replace the headlight bulb.
The headlight beam adjustment

Loosen the adjustment bolt located under the
front handle cover.
headlight beam
adjustment screw
Caution
This outer cover of headlight is a fixed type
so that the light seat will be moved only
when adjusting.
16-17

Front Turn Signal Lamp Bulb
Replacement
Remove the wire connector of the turn signal
light.
Pull out the bulb and replace it with new one.

(12V 10W)
Front turn
signal light
the wire connector of

the turn signal light
Installation
Bulbs Replacement of tail light/brake

light/rear turn signal light.
Remove the 2 screws of the tail light
assembly.
2 screws
Replace the bulbs of the tail light, brake light

(12V 5W/21W)
Replace the bulbs of the turn signal light
(12V/10W).
Installation
turn signal light
tail light & brake light
main switch connector terminals
16-18
SYM
MAIN SWITCH/HORN
Main Switch
Check
Remove the headlight connector and the front
cover.
Disconnect main switch leads connector.
Check connector terminals for continuity.
color
green green
Black Red
Location
OFF
ON
LOCK
main switch bolts x 2
Replacement
Remove the main switch connector and
fixing bolts (bolts x 2)
Remove the main switch.
Install a new main switch and tighten the
bolts. (bolts x2)
16-19

Handle switch
headlight switch

Disconnect the connector of the handle switch.
Check the continuity of follow pins listed below
columns.
Headlight switch
color
Brown
Brown Yellow Pink
Yellow
/White
Location
starting switch
Yellow/red
green
brown /white
headlight
switch
yellow
Starting switch
color
Location
pink
brown
yellow
Starting
switch
FREE
yellow/red
High/Low beam
switch/ passing
High/Low beam switch/ passing

color
brown/ White/g
blue
white
white reen
Location
green
passing
turn signal
switch
horn switch
High/Low beam
switch/ seat open
Black
Horn switch
color
Location
Blue
Black
Light green
orange
FREE
Sky blue
Black
16-20
white
brown/white
turn signal
switch
gray
Light green
Horn switch
SYM
Turn signal light switch

color Sky
Location
blue
FROM R
N
Gray
orange
orange
turn signal
light switch
PUSH OFF
FROM L
Sky blue
gray
Brake light switch

The circuit of black wire and the
green/yellow wire on the brake light switch
should be in continuity when operating the
brake lever.
If the switch damaged, replace it with new
one.
Horn
Connect the light blue wire on the horn to the
battery positive (+) terminal, and the green
wire to the battery negative (-) terminal.
Then, the horn should sound.
16-21

FUEL UNIT
Fuel unit
Open the seat.

Remove the luggage box(bolts x 6) .
Remove the engine start control switch wire
connector.
Disconnect the fuel unit wire connector.
Caution
Do not damage or bend the float arm as
removing.
The resistance values are listed below when

the float arm in F and E positions.
Float arm position
Resistance value
E(empty)
97.5~107.5
F(full)
4~10
DOWN(empty)Connect the fuel unit to the

main harness.
Turn the main switch ON position.
Move the float arm in UP & DOWN, and
then check if the fuel unit indication needle is
in correct position.
Caution
Turn on the turn signal light to make sure
battery is in good condition before this test.
Float arm position
Indicator needle
UP(full)
E(empty)
DOWN(empty)
F(full)
16-22
UP
(full)
DOWN
(empty)

FiddleII50 Service Manual

Uploaded by

Copyright:

Available Formats

FiddleII50 Service Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FiddleII50 Service Manual

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

This service manual contains the technical data of each component

HOW TO USE THIS MANUAL

GENERAL INFORMATION/TROUBLE DIAGNOSIS ...................................1

FINAL DRIVING MECHANISM.....................................................................9

High & Low beam/Passing/turn

Fuel tank / Fuel unit

Rear brake lever

Front disk brake

Front brake lever

ITEM: OUTER BEARING PULLER

ITEM: ACG FLYWHEEL PULLER

ITEM: LOCK NUT PULLER

ITEM: UNIVERSAL HOLDER

ITEM: CLUTCHSPRING COMPRESSOR

ITEM: CLUTCH NUT WRENCH

ITEM: GY6 STARTER GEAR PULLER

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

SYMBOLS AND MARKS ....................1-1

TORQUE VALUES (ENGINE) .............. 1-10

SYMBOLS AND MARKS

Special service tools.

Meaning correct installation.

Meaning wrong installation.

Indication Indication of components.

Indicates position and operation directions.

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

Do not use an compressed air or a dry brush to

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

Special tools are designed for remove and

When servicing this motorcycle, use only

Never bend or twist a control cable to prevent

Rubber parts may become deteriorated when

Note the reassemble position of the important

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

Remove residues of the old gasket or sealant

The ends of rubber hoses (for fuel, vacuum,

Tighten assemblies with different dimension

Rubber and plastic boots should be properly

When oil seal is installed, fill the groove with

The tool should be pressed against two (inner

Both of these examples can result in bearing damage.

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

Lubricate the rotation face with specified

Before battery removal operation, it has to

Check if positions and operation for installed

Make sure service safety each other when

Note that do not let parts fall down

If fuse burned, it has to find out the cause

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

Before terminal connection, check if the boot

Insert the terminal completely. Check if the

Make sure if the connector pins are bent,

Secure wires and wire harnesses to the

Insert the connector completely. If there are

Wire band and wire harness have to be

Check if the connector is covered by the twin

Do not squeeze wires against the weld or its

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS