Sym Euro MX 125 Service Manual

FORWARD CONTENTS
HOW TO USE THIS MANUAL MECHANISM ILLUSTRATIONS
SERVICE MANUAL
Home page Contents
Forward
This service manual contains the technical data of each component

inspection and repair for the SANYANG Euro MX 125 motorcycle.
The manual is shown with illustrations and focused on “Service Procedures”,
“Operation Key Points”, and “Inspection Adjustment” so that provides technician
with service guidelines.
If the style and construction of the motorcycle are different from that of the
photos, pictures shown in this manual, the actual vehicle shall prevail.
Specifications are subject to change without notice.
This manual that contains all data, illustration, indication and specifications
is based on current production information. SANYANG reserves the right to
make changes at any time without notice and without incurring any obligation
whatever. No part of this manual can be duplicated by any means without
written permission of SANYANG.
Service Department
SANYANG Industry Co., LTD.
Home page Contents
How to Use This Manual
This service manual describes basic information of different system parts

and system inspection & service for SANYANG Euro MX 125 motorcycles.
In addition, please refer to the manual contents in detailed for the model you
serviced in inspection and adjustment.
The first chapter covers general information and trouble diagnosis.

The second chapter covers service maintenance and special service tools
information.
The third to the eleventh chapters cover engine, fuel systems and driving
systems.
The twelfth to fifteenth chapters are contained the parts set of assembly
body.
The sixteenth chapter is electrical equipment.
The seventh chapter is for wiring diagram.
Please see index of content for quick having the special parts and system
information.
Home page
Contents
Page Content Index
1-1 ~ 1-16 General Information / Trouble Diagnosis 1
2-1 ~ 2-18 Service Maintenance Information 2
3-1 ~ 3-8 Lubrication System 3
4-1 ~ 4-14 Fuel System 4
5-1 ~ 5-10 Engine Removal 5
6-1 ~ 6-16 Cylinder Head / Valve 6
7-1 ~ 7-8 Cylinder / Piston 7
8-1 ~ 8-14 “V” Type Belt Driving System / Foot-Starter 8
9-1 ~ 9-6 Final Driving Mechanism 9
10-1 ~ 10-10 Alternator / Starting Clutch 10
11-1 ~ 11-6 Crankcase/Crankshaft 11
12-1 ~ 12-14 Body Cover 12
13-1 ~ 13-12 Brake System 13
14-1 ~ 14-8 Steering/Front Wheel/Suspension 14
15-1 ~ 15-4 Rear Wheel/Suspension 15
16-1 ~ 16-22 Electrical Equipment 16
17-1 ~ 17-2 Wiring Diagram 17

Home page Contents
Model illustration
Battery / Fuse
Spark plug
Winker relay AC. Generator
Horn
IG. Coil /
Start relay
Fuel tank
Headlight
Carburetor
Frame number
Seat lock
Front winker light
Tail light
Rear winker light
Air cleaner
Gear oil
Inspection plug
Gear oil drain

Engine number
plug
Engine oil drain plug
Light /
Starter switch
Rear brake
lever
Ignition switch
Front brake High & Low beam /
lever Passing /
Turn signal /
Horn switch
Oil level
Oil strainer
Exhaust
muffler
Home page Contents
1. General Information/Trouble Diagnosis
Symbols And Marks.................. 1-1 Torque Values (Frame) ........... 1-11 1

General safety ........................... 1-2 Standard Torque Values for
Reference................................. 1-11
Service Precautions.................. 1-3
Troubles Diagnosis................. 1-12
Specifications............................ 1-9
Parts To Be Greased............... 1-16
Torque Values (Engine) .......... 1-10
Symbols And Marks

Symbols and marks are used in this manual to indicate what and where the special service are
needed, in case supplemental information is procedures needed for these symbols and marks,
explanations will be added to the text instead of using the symbols or marks.
Means that serious injury or even death may result if procedures are
Warning
not followed.
Means that equipment damages may result if procedures are not
Caution
followed.
Limits to use SAE 10W-30 API SG class oil. Warranty will not cover
Engine oil the damage that caused by not apply with the limited engine oil.
(Recommended oil: KING MATE G-3 oil)
Grease King Mate G-3 is recommended. (KING MATE G-3)
King Mate gear oil (SYM HYPOID GEAR OIL ) is recommended.

Gear oil
(SAE 85W-140)
Apply sealant, medium strength sealant should be used unless
Locking sealant
otherwise specified.
Oil seal Apply with lubricant.
Renew Replace with a new part before installation.
Brake fluid Use recommended brake fluid “DOT3” or “WELLRUN” brake fluid.
Special tools Special service tools.
correct Meaning correct installation.
wrong Meaning wrong installation.
Indication Indication of components.
directions Indicates position and operation directions.
Components assembly directions each other.
Indicates where the bolt installation direction, --- means that bolt
cross through the component (invisibility).
1-1
This chapter Contents
General safety
Carbon monoxide Battery
If you must run your engine, ensure the place is Caution
well ventilated. Never run your engine in a
closed area. Run your engine in an open area, if • Battery emits explosive gases; flame is
you have to run your engine in a closed area, be strictly prohibited. Keep the place well
sure to use an extractor. ventilated when charging the battery.
Caution • Battery contains sulfuric acid (electrolyte)
which can cause serious burns so be
Exhaust contains toxic gas which may cause careful do not be spray on your eyes or
one to lose consciousness and even result in skin. If you get battery acid on your skin,
death. flush it off immediately with water. If you
get battery acid in your eyes, flush it off
Gasoline immediately with water, then go to hospital
to see an ophthalmologist.
Gasoline is a low ignition point and explosive
• If you swallow it by mistake, drink a lot of
material. Work in a well-ventilated place, no
water or milk, and take some laxative such
flame or spark should be allowed in the work
as castor oil or vegetable oil, and then go
place or where gasoline is being stored.
to see a doctor.
Caution • Keep electrolyte beyond reach of children.
Gasoline is highly flammable, and may
explode under some conditions, keep it away Brake shoe
from children. Do not use an compressed air or a dry brush to
clean components of the brake system, use a
Used engine oil
vacuum cleaner or the equivalent to avoid
asbestos dust flying.
Caution
Caution
Prolonged contact with used engine oil (or
transmission oil) may cause skin cancer Inhaling asbestos dust may cause disorders
although it might not be verdict. and cancer of the breathing system.
We recommend that you wash your hands
with soap and water right after contacting.
Brake fluid
Keep the used oil beyond reach of children.
Caution
Hot components Spilling brake fluid on painted, plastic, or

rubber parts may cause damage to the
Caution parts. Place a clean towel on the
above-mentioned parts for protection when
Components of the engine and exhaust servicing the brake system. Keep brake fluid
system can become extremely hot after beyond reach of children.
engine running. They remain very hot even
after the engine has been stopped for some
time. When performing service work on these
parts, wear insulated gloves and wait until
cooling off.
1-2
Service Precautions
• Always use with SANYANG genuine parts and • Never bend or twist a control cable to prevent
recommended oils. Using non-designed parts stiff control and premature worn out.
for SANYANG motorcycle may damage the
motorcycle.
• Rubber parts may become deteriorated when

old, and prone to be damaged by solvent and
• Special tools are designed for remove and oil. Check these parts before installation to
install of components without damaging the make sure that they are in good condition,
parts being worked on. Using wrong tools may replace if necessary.
result in parts damaged. • When loosening a component which has
different sized fasteners, operate with a
diagonal pattern and work from inside out.
Loosen the small fasteners first. If the bigger
ones are loosen first, small fasteners may
receive too much stress.
• Store complex components such as
transmission parts in the proper assemble
order and tie them together with a wire for
ease of installation later.
• When servicing this motorcycle, use only

metric tools. Metric bolts, nuts, and screws are
not interchangeable with the English system,
using wrong tools and fasteners may damage
this vehicle.
• Clean the outside of the parts or the cover
before removing it from the motorcycle.
Otherwise, dirt and deposit accumulated on
the part's surface may fall into the engine,
chassis, or brake system to cause a damage.
• Wash and clean parts with high ignition point
solvent, and blow dry with compressed air. Pay • Note the reassemble position of the important
special attention to O-rings or oil seals components before disassembling them to
because most cleaning agents have an ensure they will be reassembled in correct
adverse effect on them. dimensions (depth, distance or position).
• Components not to be reused should be
replaced when disassembled including gaskets
metal seal rings, O-rings, oil seals, snap rings,
and split pins.
1-3
• The length of bolts and screws for assemblies, • Remove residues of the old gasket or sealant
cover plates or boxes is different from one before reinstallation, grind with a grindstone if
another, be sure they are correctly installed. In the contact surface has any damage.
case of confusion, Insert the bolt into the hole
to compare its length with other bolts, if its
length out side the hole is the same with other
bolts, it is a correct bolt. Bolts for the same
assembly should have the same length.
• The ends of rubber hoses (for fuel, vacuum, or

coolant) should be pushed as far as they can
go to their connections so that there is enough
room below the enlarged ends for tightening
the clamps.
Groove
• Tighten assemblies with different dimension Clamp

fasteners as follows: Tighten all the fasteners
with fingers, then tighten the big ones with Connector
special tool first diagonally from inside toward
outside, important components should be
tightened 2 to 3 times with appropriate
increments to avoid warp unless otherwise • Rubber and plastic boots should be properly
indicated. Bolts and fasteners should be kept reinstalled to the original correct positions as
clean and dry. Do not apply oil to the threads. designed.
Boots
• The tool should be pressed against two (inner
• When oil seal is installed, fill the groove with and outer) bearing races when removing a ball
grease, install the oil seal with the name of the bearing. Damage may result if the tool is
manufacturer facing outside, check the shaft pressed against only one race (either inner
on which the oil seal is to be installed for race or outer race). In this case, the bearing
smoothness and for burrs that may damage should be replaced. To avoid damaging the
the oil seal. bearing, use equal force on both races.
Manufacturer's name
Both of these examples can result in bearing

damage.
1-4
• Lubricate the rotation face with specified • Before battery removal operation, it has to
lubricant on the lubrication points before remove the battery negative (-) cable firstly.
assembling. Notre tools like open-end wrench do not
contact with body to prevent from circuit short
and create spark.
• Check if positions and operation for installed

parts is in correct and properly.
• After service completed, make sure all
connection points is secured.
Battery positive (+) cable should be connected
firstly.
And the two posts of battery have to be
greased after connected the cables.
• Make sure service safety each other when

conducting by two persons.
• Make sure that the battery post caps are

located in properly after the battery posts had
been serviced.
• Note that do not let parts fall down.

• If fuse burned, it has to find out the cause and
solved it. And then replace with specified
capacity fuse.
capacity
verification
1-5
• Before terminal connection, check if the boot is
• When separating a connector, it locker has to crack or the terminal is loose.
be unlocked firstly. Then, conduct the service
operation.
• Insert the terminal completely.

Check if the terminal is covered by the boot.
Do not let boot open facing up.
• Do not pull the wires as removing a connector

or wires. Hold the connector body.
• Secure wires and wire harnesses to the frame

with respective wire bands at the designated
locations. Tighten the bands so that only the
insulated surfaces contact the wires or wire
• Make sure if the connector pins are bent,
extruded or loosen. harnesses.
• Insert the connector completely. • Wire band and wire harness have to be
If there are two lockers on two connector sides, clamped secured properly.
make sure the lockers are locked in properly.
Check if any wire loose.
• Check if the connector is covered by the twin • Do not squeeze wires against the weld or its
connector boot completely and secured clamp.
properly.
1-6
• Do not let the wire harness contact with • Protect wires or wire harnesses with electrical
rotating, moving or vibrating components as tape or tube if they contact a sharp edge or
routing the harness. corner. Thoroughly clean the surface where
tape is to be applied.
• Keep wire harnesses far away from the hot

parts. • Secure the rubber boot firmly as applying it on
wire harness.
NEVER TOUCH
• Route wire harnesses to avoid sharp edges or

corners and also avoid the projected ends of • Never use wires or harnesses which insulation
bolts and screws. has been broken. Wrap electrical tape
around the damaged parts or replace them.
• Route harnesses so that they neither pull too

• Never clamp or squeeze the wire harness as
tight nor have excessive slack.
installing other components.
Never clamp or
squeeze the wire
harness
NEVER TOO
TIGHT
1-7
• Do not let the wire harness been twisted as • With sand paper to clean rust on connector
installation. pins/terminals if found. And then conduct
connection operation later.
Clean rust
• Wire harnesses routed along the handlebar

should not be pulled too tight or have excessive
slack, be rubbed against or interfere with
adjacent or surrounding parts in all steering
positions.
• Before operating a test instrument, operator

should read the operation manual of the
instrument. And then, conduct test in
accordance with the instruction.
Do you know how to set the

instrument to its measurement
position and the insert
locations of its two probes?
1-8
Specifications
Maker SANYANG MODEL HF12W-6
Overall Length 1945 mm Front TELESCOPE
DIMENSION
Suspension
Overall Width 700 mm System Rear UNlT SWING
Overall Height 1160 mm Tire Front 100 / 90-12 (61L)
Wheel Base 1335 mm Specifications Rear 130 / 70 –12 (64L)
Front 48 kg
Curb Front DISK (ø 273 mm)
Rear 75 kg Brake System
Weight
Total 123 kg Rear DRUM (ø 130 mm)
Passengers/
WEIGHT
Two /110 kg PERFOR Max. Speed 96 km/hr Above

Weight
MANCE
Front 84 kg Climb Ability 28° Below
Primary
Total Rear 162 kg BELT
Reduction
Weight
Secondary
Total 246 kg GEAR
Reduction Reduction
Type 4-STROKE ENGINE Clutch Centrifugal, dry type
Installation and Vertical, below center,
Transmission C.V.T.
arrangement incline 80°
Fuel Used Unleaded Speedometer 0 ~ 140 km/hr
4-stroke/forced air
Cycle/Cooling Horn 70~90 dB/A
cooled
Bore 52.4 mm Muffler Expansion & Pulse Type
Cylinder
Exhaust Pipe Position Right side, and

Stroke 57.8 mm
and Direction Backward
ENGINE
Number/Arran
Single Cylinder Lubrication System Separated-lubrication
gement
Solid
Concentration
Displacement 124.6 cc -
Particulate
Exhaust
Compression
10.3 : 1 CO Below 4 %
Ratio
Max. HP 11.0 ps / 8250 rpm HC Below 2000 ppm
Max. Torque 1.0 kg-m / 7000 rpm E.E.C. NO
Ignition C.D.I. P.C.V. NO
Catalytic reaction
Starting System Power & Foot NO
control system
1-9
Torque Values (Engine)
Thread Dia. Torque
Item Q’ty Remarks
(mm) Value(Kg-m)
Cylinder head bolts 4 6 1.0~1.4
Cylinder head nuts 4 8 2.0~2.4

Cylinder/cylinder head two-ends
4 8 0.7~1.1 Tighten to crankcase
bolts
Cylinder head left bolts 4 6 1.0~1.4
Valve adjustment fixing nuts 4 5 0.7~1.1 Apply oil to thread
Cylinder head left cover bolts 2 6 1.0~1.4
Spark plug 1 10 1.0~1.2

Carburetor heat protector
2 6 0.7~1.1
connecting nuts
Engine oil draining plug 1 12 3.5~4.5
Engine oil strainer cap 1 30 1.0~2.0
Gear oil draining plug 1 8 0.8~1.2
Gear oil filling bolt 1 10 1.0~1.4
Oil pump screws 3 3 0.1~0.3
Engine left side cover bolts 8 6 1.0~1.5 Rubber washer attached
Camshaft chain tensioner bolt 1 6 0.35~0.5 Hex socket bolt
Camshaft chain adjuster bolts 1 6 0.8~1.2
Clutch driving plate nut 1 28 5.0~6.0
Clutch outer bracket nut 1 12 5.0~6.0
Driving disk nut 1 12 5.0~6.0
Flywheel nut 1 12 5.0~6.0
One-way clutch tighten bolts 3 6 1.0~1.4 Apply locking sealant
One-way clutch nut 1 22 9.0~10.0 Apply oil to thread

Crankcase bolts/right crank
12 8 1.5~2.0
cover bolt
Gear box cap bolts 7 8 2.0~2.4
Exhaust pipe bolts 2 8 3.0~3.6
Exhaust pipe connection nut 2 7 0.5~1.0
1-10
Torque Values (Frame)
Thread Dia. Torque
Item Q’ty Remarks
(mm) Value(Kg-m)
Mounting bolt for steering
1 10 4.0~5.0
handlebar
Mounting nut for steering rod 1 25.4 1.0~2.0
Cone seat for steering rod 1 25.4 0.2~0.3
Front wheel shaft nut 1 12 5.0~7.0
Rear wheel shaft nut 1 16 11.0~13.0
Wheel hub/rim mounting nuts 1 5 0.15~0.3
Speedometer cable locking
4 8 2.4~3.0
screw
Front shock absorber mounting
1 10 3.5~4.5
bolts
Rear shock absorber upper
1 8 2.4~3.0
connection bolt
Rear shock absorber upper
4 6 1.0~1.4
connection bolt
Brake lever bolts 2 4 0.1~0.2
Front brake hose bolts 2 6 1.0~1.4
Front brake air-bleeding valve 2 10 3.0~4.0
Front brake disc mounting bolts 1 6 0.7~1.1
Front brake clipper mounting
4 8 4.0~4.5
bolts
Drum brake arm bolts
2 8 2.9~3.5
(front/rear)
Engine suspension bracket
2 10 4.5~5.5 On frame side
bolts
Engine connection bolt 1 12 5.0~7.0 On engine side
Main standard nut 1 10 3.5~4.5
Foot-starting lever bolt 1 6 1.6~1.8
Air cleaner bolts 2 6 1.0~1.4
The torque values listed in above table are for more important tighten torque values. Please see
standard values for not listed in the table.
Standard Torque Values for Reference

Type Tighten Torque Type Tighten Torque
5mm bolt、nut 0.45~0.60 kgf-m 3mm screw 0.05~0.08 kgf-m
10mm bolt、nut 3.00~4.00 kgf-m 6mm screw、SH nut 0.70~1.10 kgf-m
12mm bolt、nut 5.00~6.00 kgf-m 6mm bolt、nut 1.00~1.40 kgf-m
8mm bolt、nut 2.40~3.00 kgf-m
10mm bolt、nut 3.50~4.50 kgf-m
1-11
Troubles Diagnosis
A. Engine hard to start or can not be started
Check and adjustment Fault condition Probable causes
Loosen carburetor drain bolt 1. No fuel in fuel tank

to check if there is gasoline 2. Check if the pipes, fuel tank to
inside the carburetor carburetor and intake vacuum, are
clogged.
3. Float valve clogged
Fuel supplied tom No fuel is supplied to 4. Lines in fuel tank evaporation system
carburetor sufficient carburetor clogged
5. Malfunction of fuel pump
Remove spark plug, install it 6. Loosen or damaged fuel pump vacuum

into spark plug cap, and hose
perform a spark test against 7. Fuel filter clogged
engine ground.
1. Malfunction of spark plug
2. Spark plug foul
3. Malfunction of CDI set
Weak sparks, no spark
Check if sparks 4. Malfunction of AC generator
at all
5. Ignition coil is in open or short circuit
6. Ignition coil leads open or short circuit
Perform cylinder 7. Malfunction of main switch
compression pressure test.
1. Piston ring seized

2. Malfunction of cylinder valves
Cylinder compression Low compression pressure
pressure normal or no pressure 3. Worn cylinder and piston ring
4. Cylinder gasket leak
5. Sand hole in compression parts
Re-start by following the
starting procedures
There are some signs of 1. Malfunction of throttle valve operation

No ignition ignition, nut engine can 2. Air sucked into intake manifold
not be started 3. Incorrect ignition timing
Remove the spark plug

again and check it.
1. Fuel level in carburetor too high

Dry spark plug Wet spark plug 2. Malfunction of throttle valve operation
3. Throttle valve opening too wide
Remove carburetor after 30

minutes and connect a hose
onto fuel rich circuit. Then
blow the hose with air
Blowing in normal Blowing clogged 1. Malfunction of automatic by- starter
1-12
B. Engine run sluggish (Speed does not pick up, lack of power)
Try gradual acceleration

and check engine speed
0. Air cleaner clogged

Engine speed can be Engine speed can not 1. Poor fuel supply
increased. be increased. 2. Lines in fuel tank evaporation
system clogged
3. Exhaust pipe clogged
4. Fuel level too low in carburetor
Check ignition timing
(Using ignition lamp) 5. Fuel nozzle clogged in carburetor.
Ignition timing correct Incorrect ignition timing 1. Malfunction of CDI

2. Malfunction of AC alternator
Check cylinder compression

pressure (using compression
pressure gauge)
1. Cylinder & piston ring worn out
2. Cylinder gasket leaked
Compression pressure correct No compression pressure 3. Sand hole in compression parts
4. Valve deterioration
5. Seized piston ring
Check if carburetor jet is
clogged
No clogged Clogged 1. Remove foreign
Remove spark plug
No foul or discoloration Fouled and discoloration 1. Remove dirt

2. Incorrect spark plug heat range
Check if engine over heat

1. Piston and cylinder worn out
2. Lean mixture
3. Poor fuel quality
Normal Engine overheat 4. Too much carbon deposited in
combustion chamber
5. Ignition timing too advanced
Continually drive in 6. Poor circuit on the cooling system
acceleration or high speed
1. Too much carbon deposited in

combustion chamber
No knock Knock 2. Lean mixture
3. Poor fuel quality
4. Ignition timing too advanced
1-13
C. Engine runs sluggish (especially in low speed and idling)
Check ignition timing (using

ignition lamp)
Normal Abnormal 1. Incorrect ignition timing (malfunction of

CDI or AC alternator)
Adjust the air screw of

carburetor
Good Poor 1. Rich mixture (loosen the screw)

2. Lean mixture (tighten the screw)
Air sucked through carburetor

gasket
1. Poor heat insulation gasket
2. Carburetor lock loose
No air sucked Air sucked 3. Poor intake gasket
4. Poor carburetor O-ring
5. Vacuum hose crack
Remove spark plug, install
spark plug into spark plug cap
and perform spark test
against engine ground 1. Spark plug fouled
2. Malfunction of CDI
3. Malfunction of AC generator
Good spark Poor 4. Malfunction of ignition coil
5. Open or short circuit in spark plug
leads
6. Malfunction of main switch
D. Engine runs sluggish (High speed)
Check ignition timing
Normal Abnormal 1. Malfunction of CDI

2. Malfunction of AC alternator
Check for fuel supplying system
in automatic fuel cup
1. Insufficient fuel in fuel tank

Good Poor 2. Fuel filter clogged
3. Restricted fuel tank vent
Check if carburetor clogged
No clogged Clogged 1. Cleaning
1-14
E. Clutch, driving and driving pulley
FAULT CONDITIONS PROBABLE CAUSES
1. Drive belt worn out or deformation

2. Ramp plate of movable drive face damaged
Engine can be started but
3. Driving pulley spring broken
motorcycle can not be moved.
4. Clutch weights broken
5. Drive slide-shaft gear groove broken
6. Transmission gear damaged
Engine running and misfire as

1. Clutch weights spring broken
motorcycle initial forward moving
or jumping suddenly (rear wheel 2. Clutch outer stuck with clutch weights
rotating as engine in running) 3. Connection parts in clutch and shaft worn out or
burned
1. Drive belt worn out or deformation

2. Weight roller worn out
Poor initial driving ( Poor climbing
performance) 3. Movable drive face shaft worn out
4. Driven pulley spring deformation
5. Driven pulley shaft worn out
6. Greased in drive belt and driven face.
1-15
Parts To Be Greased
Acceleration cable/ Front & rear

brake lever pivot
Steering shaft bearing Seat lock catch
Speedometer gear/ Side stand pivot Main stand pivot Rear wheel bearing
front wheel bearing
1-16
Home page Contents
2. Maintenance Information
Precautions In Operation .......... 2-1 Spark Plug .................................. 2-8

Periodical Maintenance Cylinder Compression
Schedule ..................................... 2-2 Pressure...................................... 2-9 2
Lubrication System.................... 2-3 Driving System ........................... 2-9
Gear Oil ....................................... 2-4 Steering System ....................... 2-10
Fuel System................................ 2-4 Suspension System ................. 2-10
Air Cleaner.................................. 2-5 Disk Brake System (Front Disk
Brake) ........................................ 2-11
Throttle Valve Operation ........... 2-5
Drum Brake System ................. 2-13
Crankcase Ventilation ............... 2-6
Wheel / Tire ............................... 2-14
Valve Clearance Adjustment..... 2-6
Battery....................................... 2-15
Valve Clearance Inspection
And Adjustment ......................... 2-7 Headlamp Adjustment ............. 2-15
Carburetor Idle Speed Nuts, Bolts Tighteness ............ 2-15
Adjustment ................................. 2-7
Special Service Tools
Ignition System .......................... 2-8 Catalogue.................................. 2-16
Precautions In Operation
Specification
Fuel Tank Capacity 7500 c.c.
Capacity
1000 c.c.
Engine Oil
Change800 c.c.
Capacity
110 c.c.
Transmission Gear oil
Change100 c.c.
Clearance of throttle valve 2~6 mm
Spark plug NGK CR8E Gap: 0.8 mm
“F” Mark in idling speed BTDC 13º / 1700 rpm
Full timing advanced BTDC 27º / 8000 rpm
Idling speed 1600±100 rpm
Cylinder compression pressure 10.3 ± 0.2 kgf/cm²
Valve clearance: IN/EX 0.12 ± 0.02 mm
Front 110/80-12 61L
Tire dimension
Rear 130/70-12 64L
Single Front: 1.75 kg/cm² rear : 2.25 kg/cm²
Tire pressure (cold)
Two persons Front: 1.75 kg/cm² rear : 2.50 kg/cm²
Battery 12V8Ah (MF battery) type: YTX9A-BS (8Hr)
2-1
Periodical Maintenance Schedule
Maintenance Initial 1 Month 3 month 6 month 1 year
Code item 300KM every1000KM every3000KM every6000KM every12000KM
1 ☆Air cleaner I C C R
2 ☆2nd air jet cleaner I C C R
3 ☆Fuel filter I I R
4 ☆Oil filter C C C
5 ☆Engine oil change R Replacement for every 1000km
6 Tire pressure I I
7 Battery inspection I I
8 Brake & free play check I I
9 Steering handle check I I
10 Cushion operation check I I
11 Every screw tightening check I I
12 Gear oil check for leaking I I
13 ☆Spark plug check or change I I R
14 ☆Gear oil change R Replacement for every 5000km
15 Frame lubrication L
16 Exhaust pipe I I
17 ☆Ignition timing I I
18 ☆Emission check in Idling A I
19 ☆Throttle operation I I
20 ☆Engine bolt tightening I I
21 ☆CVT driving device(belt﹞ I R
22 ☆CVT driving device(roller) C
23 Lights/electrical equipment/mutli-meters I I
24 Main/side stands & springs I I
25 Fuel lines I I
27 Cam chain I I
28 ☆Valve clearance I A
Note: I - Inspection, A-Adjustment R- Replacement C- Cleaning L- Lubrication (The 33rd, 34th, and 35th items are
for the fuel injection system)
The above maintenance schedule is established by taking the monthly 1000 kilometers as a reference which ever comes
first.
Remarks: 1. These marks ”☆” in the schedule are emission control items. According to EPA regulations, these items must be
perform normally periodical maintenance following the user manual instructions.
2. Clean or replace the air cleaner element more often when the motorcycle is operated on dusty roads or in the
Heavily- polluted environment.
3. Maintenance should be performed more often if the motorcycle is frequently operated in high speed and after
the motorcycle has accumulated a higher mileage.
4. Preventive maintenance
a. Ignition system - Perform maintenance and check when continuous abnormal ignition, misfire, after-burn,
overheating occur.
b. Carbon deposit removal - Remove carbon deposits in cylinder head, piston heads, exhaust system when
power is obvious lower than ever.
c. Replace worn out pistons, cylinder head.
2-2
Lubrication System
Engine Oil Capacity
Caution
• The vehicle must be parked on a level
ground when checking oil capacity.
• Run the engine for 3-5 minutes then stop,
wait about 3-5 more minutes allowing
engine oil to settle before checking the oil
level.
Remove dipstick to check the oil level. If oil level

is below the lower limit mark, add oil to the
specified upper limit mark.
Engine Oil change
Shut off the engine and remove dipstick.
Remove the oil drain plug on the bottom-left of
crankcase to drain oil.
After draining out oil, clean oil plug and its gasket
and reinstall. Replace the gasket if it is damaged.
Torque value: 3.5~4.5 kgf-m
Caution
Warm up the engine. This will make the oil
flow out easily.
Oil drain plug
Add oil to the specified capacity.
Oil Viscosity: SAE 10W-30, or equivalent
recommended using King-Mate serial oil.
Engine oil capacity: Disassembly: 1050cc
Change: 800cc
When checking for oil leak, run the engine at idle
speed for a few minutes, then check oil capacity
with dipstick.
Cleaning the oil strainer

Drain oil from engine, remove the strainer cover,
spring and strainer.
If there is an accumulation on the screen, wash it
off with suitable solvent (recommended using
compressed air to cleaning the foreign).
Check O-ring for damage, replace if necessary.
Reinstall strainer, spring, O-ring and strainer
cover.
2-3
Gear Oil
Inspection
Check gear oil if leaking.
Park the motorcycle with main stand on flat level
place.
Turn off engine and remove the gear oil draining
plug.
Place a measurement cup under the draining
hole.
Check gear oil if enough.
Gear oil
Replacement refilling bolt
At first, remove the gear oil refilling bolt, and then
remove the draining plug.
Install the draining plug after drained oil out.
Caution
Inspect if washer is in good condition.
Replace it with new one if it was deformed or
damaged.
Fill out specified gear oil from the engine oil filling
opening.
Install the oil filling bolt. Gear oil draining plug
Quantity: 100 c.c. Fuel pipes
Recommended: King-Mate HYPOID GEAR OIL
(#140)
Fuel System
Fuel Lines
Remove luggage box.
Check all lines, and replace it when they are
deterioration, damage or leaking.
Warning
Gasoline is a low ignition material so any kind
of fire is strictly prohibited as dealing it.
Fuel filter
Remove luggage box.
Check if the fuel filter is clogged, broken. If so,
replace the fuel filter with new one.
Fuel filter
2-4
Air Cleaner
Air element 6 screws
Remove the air cleaner cover (6 screws).
Remove the lock plate from the element of air
cleaner.
Check the element if dirt or damaged.
If it dirt, clean it with solvent and then soap it into
cleaning engine oil after cleaned. Finally,
squeeze it.
Replace it with new one if dirt or damaged.
Caution
• Make sure that the air cleaner cover had

been installed properly after installation
because improperly installation will cause
foreign sucking into cylinder.
• Do not wet the air cleaner as washing the
motorcycle. Or it may effect engine
performance.
Throttle Valve Operation

Have a wide open of throttle valve as handle bar
in any position and release it to let back original
(full closed) position.
2~6 mm
Check handle bar if its operation is smooth.
Check throttle valve cable and replace it if
deteriorated, twisted or damaged.
Lubricate the cable if operation is not smooth.
Measure handle bar free play in its flange part.
Free play：2~6 mm
Adjustment can be done in either ends.

Secondary adjustment is conducted from top
side.
Remove rubber boot, loosen fixing nut, and then
adjust it by turning the adjustment nut.
Rubber boot
Fixing nut
Adjustment nut
2-5
Primary adjustment is conducted from button
Adjustment nut
side of cable on the throttle body.
Loosen fixing nut, and adjust by turning the
adjustment nut for its free-play.
Tighten the fixing nut, and check acceleration
operation condition after adjusted.
Fixing nut
Crankcase Ventilation
Pull out the plug from draining hose to clean
deposits.
Caution
When always riding in rainy area or full

throttle position, maintenance travel must be
shorted. The deposits can be seen in the
transparent section of draining hose.
Crankcase blow-by plug

Valve Clearance Adjustment
Caution
Checks and adjustment must be performed
when engine is cold (below 35℃).
Remove luggage box.

Remove center cover.
Remove cylinder head left cap.
Remove the ignition timing check hole cap on the
cooling fan cover.
With T type wrench, turn crankshaft in clockwise
motion so that mark (T) on the generator flywheel TDC mark
aligns with the mark on the crankshaft, and
camshaft is at TDC position also as same as
level of cylinder head top-end. A single hole on
camshaft sprocket is forward to up. (Piston is at
TDC position in the compression stroke.)
Caution
The model that equipped with starting
compression pressure reduction system can
Ignition
not be rotated in counter-clockwise to prevent timing
from operating compression pressure mark
reduction function so that valve clearance can
not be measured.
2-6
Valve Clearance Inspection And
Adjustment
Check & adjust valve clearance with feeler
gauge.
Valve clearance (IN/EX): 0.12 ± 0.02 mm
Loosen fixing nut and turn the adjustment nut for
adjustment.
Caution
It has to make sure that valve rock-arm is be

adjusted to standard level when adjusting it,
and re-check the valve clearance after
tightened the fixing nut.
High voltage coil cable
Carburetor Idle Speed Adjustment

Caution
y Inspection & adjustment for idle speed
have to be performed after all other parts
in engine that needed adjustment have
been adjusted.
y Idle speed check and adjustment have to
be done after engine is being warm up
(around 10 minutes).
Park the motorcycle with main stand and
warn up engine.
Connect tachometer (the wire clamp of
tachometer is connected to the high voltage
coil).
Open the carburetor cover from the trunk.
Turn the throttle valve stopper screw to
specified idle speed.
Specified idle speed: 1700±100 rpm
Emission adjustment in Idle speed
Warm up the engine for around 10 minutes
and then conduct this adjustment.
1. Connect the tachometer onto engine.
2. Adjust the idle speed adjustment screw and Throttle valve stopper screw
let engine runs in 1700±100 rpm.
3. Insert the exhaust sampling pipe of exhaust
analyzer into the front section of exhaust
pipe. Adjust the air adjustment screw so
that emission value in idle speed is within
standard.
4. Slightly accelerate the throttle valve and
release it immediately. Repeat this for
2~3 times.
5. Read engine RPM and value on the
exhaust analyzer. Repeat step 2 to step 4
procedures until measured value within
standard.
Emission standard: CO: below 4.0%
HC: below 2000 ppm Air adjustment screw
2-7
Ignition System
F mark
Ignition Timing
Caution
C.D.I ignition system is set by manufacturer
so it can not be adjusted.
Ignition timing check procedure is for Ignition
lamp
checking whether CDI function is in normal or
Remove right side cover.
Remove ignition timing hole cap located on the
cooling fan cap.
Connect tachometer and ignition lamp.
Start engine and set engine idle speed in 1600
rpm, and if the mark aligns with the “F”, then it
means that ignition timing is correct.
Increase engine speed to 8000 rpm to check
ignition timing advance. If the detent aligns with
advance mark “‫”װ‬, then it means ignition timing
advance is in functional.
If not, check CDI set, pulse flywheel, and pulse
generator. Replace these components if
malfunction of these parts are found.
Spark Plug
Appointed spark plug：CR8E (NGK)
Spark plug cap
Remove luggage box.
Remove central cover.
Remove spark plug cap.
Clean dirt around the spark plug hole.
Remove spark plug.
Measure spark plug gap.
Spark plug gap: 0.8 mm
Carefully bend ground electrode of the plug to
adjust the gap if necessary.
Hold spark plug washer and install the spark plug
by screwing it. Tighten the plug by turning 1/2
turn more with plug socket after installed.
Connect spark plug cap. Side electrode
Central electrode
0.8mm
2-8
Cylinder Compression Pressure
Warn up engine and then turn off the engine.
Remove the luggage box and the center cover.
Remove spark plug cap and spark plug.
Install compression gauge.
Full open the throttle valve, and rotate the engine
by means of stepping the foot-starting lever.
Caution
Rotate the engine until the reading in the
gauge no more increasing.
Usually, the highest pressure reading will be Spark plug
obtained in 4~7 seconds.
Compression pressure: 10.3 ± 0.2 Kg/cm²

Check following items if the pressure is too low:
• Incorrect valve clearance
• Valve leaking
• Cylinder head leaking, piston, piston ring and Cylinder
pressure
cylinder worn out
gauge
If the pressure is too high, it means carbon
deposits in combustion chamber or piston head.
Driving System Gear teeth

Drive Belt
Remove left side cover.
Remove mounting bolt located under air cleaner. Width
Remove 9 bolts of the engine left side cover and
the cover.
Check if the belt is crack or worn out.
Replace the belt if necessary or in accord with
the periodical maintenance schedule to replace
it.
Width limit: 18.5mm or more
Clutch pad
Clutch Pad
Start the motorcycle and gradually increase
throttle valve openness to check clutch pad
operation.
If the motorcycle moves with shaking, then check Clutch
its clutch pad for wearing. Replace it if
necessary.
2-9
Steering System
Caution
Check all wires and cables if they are
interfered with the rotation of steering handle
bar.
Lift the front wheel out of ground.

Turn handle from right to left alternative and
check if turning is smoothly.
If handle turning is uneven and bending, or the
handle can be operated in vertical direction, then
adjust the handle top bearing.
Suspension System
Warning
• Do not ride the motorcycle with poor shock
absorber.
• Looseness, wear or damage shock
absorber will make poor stability and drive
ability.
Front shock absorber

Hold front brake lever and press down the front
shock absorber for several times to check its
operation.
Hold front brake lever and push forward the front
shock absorber for several times to check its
locking status.
Check if it is scratched or leaking.
Replace damaged and non-repairable
components.
Tighten all nuts and bolts.
Rear Shock absorber

Press down the rear shock absorber for several
times to check its operation.
Check if it is scratched or leaking.
Replace damaged and non-repairable
components.
Park the motorcycle with main standard.
Start engine and let the rear wheel rotate after
increased engine rpm. Check engine for any
parts loose or shaking. Also check the engine
suspension bushing for wear out. Replace the
bushing if worn out.
Tighten all nuts and bolts.
2-10
Disk Brake System (Front Disk
Brake metals hose
Brake)
Brake System Metal Hoses
Make sure the brake metal hoses for corrosion or
leaking oil, and also check brake system for
leaking.
Brake Fluid
Check brake fluid level in the brake fluid reservoir.
If the level is lower than the LOWER limit, add
brake fluid to UPPER limit. Also check brake Master
system for leaking if low brake level found. cylinder
cap
Caution
In order to maintain brake fluid in the reservoir

in horizontal position, do not remove the cap
until handle bar stop.
Do not operate the brake lever after the cap
had been removed. Otherwise, the brake
fluid will spread out if operated the lever.
Do not mix non-compatible brake fluid
Lower limit
together.
Filling Out Brake Fluid Screws

Tighten the drain valve, and add brake fluid.
Master cylinder cap
Place the diaphragm in.
Diaphragm plate
Operate the brake lever so that brake fluid
Diaphragm
contents inside the brake system hoses.
Upper limit
Air Bleed Operation
Connect a transparent hose to draining valve.
Hold the brake lever and open air bleeding valve.
Perform this operation alternative until there is no
air inside the brake system hoses.
Caution
Before closing the air bleed valve, do not Draining valve
release the brake lever. Bubbles
Added Brake Fluid

Add brake fluid to UPPER limit lever.
Recommended brake fluid: DOT3 or DOT4
WELL RUN brake fluid.
Caution
Never mix or use dirty brake fluid to prevent
from damage brake system or reducing brake
Transparent draining hose
performance.
2-11
Brake Lining Wear
The indent mark on brake lining is the wear
limitation.
Brake lining
Replace the brake lining if the wear limit mark wear limit
closed to the edge of brake disc.
Caution
It is not necessary to remove brake hose

when replacing the brake lining.
Brake clipper Brake disc
Remove the brake clipper bolt, and take out the

clipper.
Caution Brake
clipper bolt
Do not operate the brake lever after the
clipper removed to avoid clipping the brake
lining.
Pry out the brake lining with a flat driver if lining

be clipped.
Remove brake lining bolt.

Take out the lining. Brake lining
Caution
In order to maintain brake power balance, the
brake lining must be replaced with one set.
Bolt
Brake Lamp Switch

The brake lamp switch is to lit up brake lamp as Master
brake applied. cylinder
Make sure that electrical starter can be operated
only under brake applying.
Brake lamp
switch
2-12
Drum Brake System
Rear Brake Free Play: (Drum brake)
Measure free play of rear brake level at the end 10∼20mm
of the lever.
Free play: 10-20 mm
Measure the free play of the front brake lever at

the end of the lever.
Free play: 10-20 mm Decreasing
Adjustment nut free play
Adjust the free play by turning the front brake
adjustment nut if necessary.
Increasing
free play
Brake Confirmation
Caution
y After brake adjustment, it has to check
the brake operation to make sure the “△”marks
front and rear wheel can be braked.
y Pull the brake lever, and make sure that
the wear limit marks of brake ling on the
both front & rear brake arm are closer
and touch to the “△” marks. If so,
replace the brake ling with new one.
Brake Lamp Switch

The brake lamp switch is to lit up brake lamp Brake lamp switch
as brake applied.
Make sure that electrical starter can be operated
only under brake applying.
2-13
Wheel / Tire
Check if both front & rear tires’ pressure is in
correct.
Caution
Tire pressure check should be done as cold
tire.
Appointed tire pressure

Tire size Front tire Rear tire
Load for
Tire pressure 1.75 2.25
single
as cold tire
Load for two
(Kg/cm²) 1.75 2.5
persons
Appointed Tire
Front wheel: 100/90-12 59J (T/L)
Rear wheel: 130/70-12 59J (T/L)
Check if tire surface is ticked with nails, stones or
other materials.
Check if tire surface or wall for crack or damaged,
and replace it if necessary.
The tire tread depth can be checked by visual
inspection or depth gauge.
•Replace the tire if tire tread dent or unusual
wearing out.
•The tire should be replaced if the wear limit
mark “△” is in visible.
Measure tire thread depth from tire central
surface.
Replace the tire if the depth is not come with
following specification:
Front tire: 1.5 mm
Rear tire: 2.0 mm
Caution
The wear limit marks “∆” are located around

the tire wall even for inspection. Wear limit indicator “△” mark
2-14
Battery
Battery Removal
Remove right cover. (3 screws)
Battery cables removal:

1. At first, remove the negative “-” cable.
2. Then, remove the positive “+” cable.
3. Remove the battery.
If there is some rust on battery posts, clean it

with steel brush.
Install the battery in the reverse procedures of
removal.
Caution
• If there is rust on the posts very serious,
spray some hot water on the posts.
Then, clean it with steel brush so that
can remove rust for more easily.
• Apply some grease on the posts after
rust removed to prevent from rust again.
Headlamp Adjustment
Headlamp adjustment
Remove the front fender.
Turn the headlamp adjustment screw to adjust
headlamp beam height. (C.W. is for increasing
beam height, and C.C.W. is for decreasing beam
height)
Reinstall the front fender.
Caution
Headlamp adjustment screw
• To adjust the headlamp beam follows
related regulations. Do not adjust it
arbitrarily if not necessary.
• Improper headlamp beam adjustment will
make in coming driver dazzled or
insufficient lighting.
Nuts, Bolts Tighteness

Perform periodical maintenance in accord with
the Periodical Maintenance Schedule.
Check if all bolts and nuts on the frame are
tightened securely.
Check all fixing pins, snap rings, hose (pipe)
clamps, and wire holders for security.
2-15
Special Service Tools Catalogue
(ψ30mm) (ψ22mm)
Alternator fly wheel Puller/presser for Puller/presser for
Name Name Name
remover crankcase bushing crankcase bushing
Parts no. SYM-3110A01 Parts no. SYM-1120310 Parts no. SYM-1120320
Presser for crankcase Valve spring Valve spring

Name Name Name
bushing compressor compressor
Parts no. SYM-1120300-H9A Parts no. SYM-1471100 Parts no. SYM-1471110/20
Valve clearance Clutch spring

Name Name Universal fixer Name
adjustment wrench compressor
Parts no. SYM-9001200 Parts no. SYM-2210100 Parts no. SYM-2301000
Bearing remover (inner Bearing remover (outer

Name Valve clearance adjuster Name Name
type) type)
2-16
(6301) (6204) (6203/6004UZ)

Bearing installer ψ
Name Bearing installer Name Bearing installer Name
17mm
(27*42*7) (25*40*8) (20*32*6)
Name Oil seal installer Name Oil seal installer Name Oil seal installer
Clutch mounting bolt Valve cap / Oil filter cap

Name Name
wrench wrench
Parts no. SYM-9020200 Parts no. SYM-1236100
2-17
NOTE:
2-18
Home page Contents
3. Lubrication System
Mechanism Illustration .............. 3-1 Oil Pump Disassembly .............. 3-4

Operational Precautions:........... 3-2 Oil Pump Inspection .................. 3-5
Trouble Diagnosis ...................... 3-2 Oil Pump Re-assembly .............. 3-5
3
Engine Oil ................................... 3-3 Oil Pump Installation ................. 3-6
Cleaning Engine Oil Strainer..... 3-3 Gear Oil....................................... 3-7
Oil Pump Removal ..................... 3-4
Mechanism Illustration
Rock Arm
Forcedly lubrication
Cam Shaft
Scoop lubrication
Inner passage
Connecting rod
Forcedly lubrication
Crankshaft
Oil strainer Oil pump
3-1
Operational Precautions:
General Information
z This chapter contains maintenance operations for the engine oil pump, engine oil and gear oil.
Specifications
Oil viscosity
Engine oil quantity Disassembly 1000 c.c.
Replacement 800 c.c
Oil viscosity SAE 10W-30 or equivalent
(Recommended King-Mate
serial oils)
Gear Oil Disassembly 110 c.c.
Replacement 100 c.c.
Oil viscosity of gear oil SAE 85W-140
(Recommended King-Mate
gear oil series SYM
HYPOID GEAR OIL)
unit: mm
Items Standard (mm) Limit (mm)
Inner rotor clearance - 0.12

Oil pump Clearance between outer rotor and body - 0.12
Clearance between rotor side and body 0.05~0.10 0.20
Torque value
Engine oil drain plug 3.5~4.5 kgf-m
Engine oil filter cover 1.3~1.7 kgf-m
Gear oil drain plug 0.8~1.2 kgf-m
Gear oil filling bolt 1.0~1.4 kgf-m
Oil pump connection screw 0.1~0.3 kgf-m
Trouble Diagnosis
Low engine oil level Dirty oil
• Oil leaking • No oil change in periodical
• Valve guide or seat worn out • Cylinder head gasket damage
• Piston ring worn out • Piston ring worn out
Low Oil Pressure

• Low engine oil level
• Clogged in oil strainer, circuits or pipes
• Oil pump damage
3-2
Engine Oil
Turn off engine, and park the motorcycle in flat
surface with main stand. Check oil level with oil
dipstick after 3-5 minutes.
Do not screw the dipstick into engine as
checking.
If oil level is nearly low level, fill out
recommended oil to upper level.
Oil Replacement
Oil stick
Caution
Drain oil as engine warmed up so that make Drain plug
sure oil can be drained smoothly and
completely.
Place an oil pan under the motorcycle, and

remove oil strainer cap.
Make sure if the aluminum washer of the
draining bolt is damaged. If so, replace it with
new one.
Install the drain bolt and tighten it.
Cleaning Engine Oil Strainer

Remove the oil strainer cap.
Remove oil strainer and spring.
Clean oil strainer. (Recommended using
compressed air to clean dirty foreign.)
Check if the strainer and O-ring of the oil strainer
are broken. Replace with new one if found.
Install the oil strainer and spring.
Install the oil strainer cap and tighten it.
Fill out oil to the oil filler. (Oil viscosity SAE Oil filter cover
10W-30) (Recommended King-Mate serial oils)
Engine oil quantity: Replacement 800 c.c.
After oil replaced, insert ignition key into the
re-set bottom under instrument panel so that the
oil indicator is changed from red to green and set
oil replacement mileage to zero.
Install dipstick, start the engine for running
several minutes.
Turn off engine, and check oil level again if within
standard level after 3-5 minutes.
Check if engine oil leaks.
3-3
Oil Pump Removal
Remove the alternator (refer to chapter 10).
Remove the engine right cover.
Remove the one-way clutch and starting gear
(1 nut).
Make sure that the pump axle can be rotated
freely.
Remove the oil pump cover (2 screws), and then
the oil pump driving gear clamp and the gear.
Remove oil pump body screws (3 screws).
Oil Pump Disassembly

Remove the screws on oil pump cover and
disassemble the pump as illustration shown.
Engine right cover
Starting gear
Starting
起動離合器組clutch
Right crankcase
cover
Oil pump driving gear
Oil pump body
Oil pump shaft

Outer rotor
Inner rotor
Oil pump cover
Oil pump outer cover
3-4
Oil Pump Inspection
Check the clearance between oil pump body and
outer rotor.
Limit：below 0.12mm
Check clearance between inner and outer rotors.

Limit: below 0.12mm
Check clearance between rotor side face and

pump body.
Limit: below 2.0 mm
Oil Pump Re-assembly

Install inner and outer rotors into the pump body.
Align the indent on driving shaft with that of inner
rotor. Install the driving shaft.
Install the oil pump cover and fixing pin properly
and then tighten screw. (1 screw)
3-5
Install driving gear and clamp.
Caution
Install the oil pump cover and fixing pin

properly.
Oil Pump Installation

Install the oil pump (3 screws).
Caution
The elliptical hole on the driving gear is not

match with the screw hole. Thus, the elliptical
hole has to align with the screw hoe before
tightening it.
3 screws
Install oil pump outer cover (2 bolts).
2 screws
Install the starting gear and the alternator.

(Refer to chapter 10)
3-6
Gear Oil
Oil Level Inspection
Park the motorcycle on flat surface with main
stand.
Turn off engine and remove both engine oil filling
bolt and oil draining plug.
Filling bolt
Remove gear oil filling hole bolt and place a

measurement cup under the draining plug.
Remove the oil draining plug and the pour gear
oil into the measurement cup. Measure the
gear oil quantity if within standard value.
Add specified gear oil if the oil level too low.
(Standard quantity: 110cc. / replacement: 100
cc.)
Draining plug
Gear Oil Replacement

Remove the gear oil filling hole bolt and its
draining plug and then drain oil completely.
Install the draining plug and tighten it (Make sure
if the plug washer is damaged. If so, replace it
with new one.)
Torque Value: 0.8~1.2 kgf-m
Add new gear oil (100 c.c.) from the gear oil
filling hole and then install the gear oil filling hole
bolt after added oil. And then, tighten the bolt.
※Recommended to apply with SYM HYPOID
GEAR OIL (SAE 85W-140)
Start engine and run it for 2~3 minutes.
Turn of f engine and check if oil leaking.
3-7
NOTES:
3-8
Home page Contents
4. FUEL INJECTION SYSTEM
Mechanism Illustration............. 4-1 Float Chamber ........................... 4-8

Precautions In Operation ......... 4-2 Installation Of Carburetor ......... 4-9
Trouble Diagnosis .................... 4-3 Idle Speed Adjustment .............. 4-9
Carburetor Removal ................. 4-4 Fuel Tank.................................. 4-10
Air Cut-off Valve........................ 4-6 Air Cleaner ............................... 4-13 4
Auto By-Starter ......................... 4-7
Fuel unit
Fuel vapor return hose
Fuel hose
Fuel tank
Fuel hose
Fuel cap Fuel filter

(Vacuum type)
Carburetor
Vacuum hose
4-1
General Information
Warning
Gasoline is a low ignition point and explosive materials, so always work in a well-ventilated place
and strictly prohibit flame when working with gasoline.
Cautions
y Do not bend or twist throttle valve cable. Damaged cable will make unstable drive ability.
y When disassembling fuel system parts, pay attention to O-ring position, replace with new one as
re-assembly
y There is a drain screw in the float chamber for draining residual gasoline.
y Do not disassemble automatic by-starter and air cut-off valve arbitrarily.
Specification
Item Specification
Carburetor diameter 24 mm
I.D. number 063c
Fuel level 17.5 mm
Main injector # 92
Idle injector # 35
Idle speed 1700±100 rpm
Throttle handle free play 2~6 mm
Fuel quantity adjustment screw 1 3/4±3/4 turns
Torque value
Fuel valve tightening nut: 1.5~2.0 Kgf-m
Tool
Special service tools
Vacuum/air pressure pump
General service tools
Fuel level gauge
4-2
Trouble Diagnosis
Poor engine start Power insufficiency and fuel consuming
y No fuel in fuel tank y Fuel system clogged
y Clogged fuel tube y Malfunction of ignition system
y Too much fuel in cylinder
y No spark from spark plug (malfunction of
ignition system)
y Clogged air cleaner
y Malfunction of automatic by-starter Mixture too lean
y Malfunction of throttle valve operation y Clogged fuel injector
y Vacuum piston stick and closed
y Malfunction of float valve
y Fuel level too low in float chamber
y Clogged fuel tank cap vent
Stall after started
y Clogged fuel filter
y Malfunction of automatic by-starter
y Obstructed fuel pipe
y Incorrect ignition timing
y Clogged air vent hose
y Malfunction of carburetor
y Air existing in intake system
y Dirty engine oil
y Air existing in intake system
y Incorrect idle speed
Mixture too rich

y Clogged air injector
y Malfunction of float valve
Rough idle
y Fuel level too high in float chamber
y Malfunction of ignition system
y Malfunction of automatic by-starter
y Incorrect idle speed
y Dirty air cleaner
y Dirty fuel
Intermittently misfire as acceleration

Late ignition timing

4-3
Carburetor Removal Throttle Vacuum hose
Remove the trunk. valve cable
Loosen the adjustment nut and fixing nut of
throttle valve cable, and release the cable from
carburetor.
Remove fuel pipe, vacuum hose.
Disconnect auto by-starter connectors.
Release the clamp strip of air cleaner.
Release the clamp strip of carburetor isolator.
Take the carburetor out.
Clamp strip of isolator
Vacuum
hose
Auto by-starter
Vacuum Chamber Screws ×2

Removal
Loosen drain screw, and drain out residual fuel in
float chamber.
Remove screws (2 screws) of vacuum chamber
cover and the cover.
Remove compress spring and vacuum piston.
4-4
Remove fuel needle seat, spring, and injector
Fuel needle
needle. seat
Check if the vacuum piston for wear out, crack or
other damage. Fuel needle
Check if the diaphragm for damage or crack. spring
Cautions Injector
needle
Do not damage vacuum diaphragm.
Piston Piston spring
Installation
Install injector needle, spring and fuel needle
seat to vacuum piston.
Cautions
y Note direction as installing the piston set
because wrong direction of the piston cab
not be installed.
y Align the indent of vacuum diaphragm with
the carburetor body.
Piston diaphragm lock position
Install vacuum piston to carburetor body.
Install compress spring.
Install vacuum chamber cover and tighten 2 Screws ×2

screws.
4-5
Air Cut-off Valve
Removal
Remove the vacuum hose clamp and then the
vacuum hose.
Screws ×2
Remove the screws (screw x 2) of the air cut-off

valve and its cover.
Remove the spring and vacuum diaphragm.

Check if the diaphragm for deterioration or crack.
Installation
Install the valve as reverse order of removal.
Cautions
Do not damage the vacuum diaphragm or in
opposite installation direction.
4-6

Auto By-Starter
Inspection
Turn off engine and waiting for over 10 minutes
for cooling.
Check resistance across the two terminals of the
auto by-starter
Resistance value: Max. 10Ω (Measured after
engine stopped for more than 10 minutes)
Replace the auto by-starter with a new one if
resistance value exceeds standard.
Remove the carburetor, allow it to cool off for 30
minutes.
Connect a hose to fuel increase circuit.
Pump compressed air to the circuit.
Replace the auto by-starter if the circuit clogged.
Connect battery posts (12V) to starter’s

connectors. After 5 minutes, test the increase
circuit with compressed air. If air flow through
the circuit, then replace the starter.
Removal
Remove fixing plate screw, and then remove the
plate and auto by-starter from carburetor. Auto by-starter
Round point
Valve inspection
Check if auto by-starter and valve needle for Screws
damage or wear out. ×2
Fixing plate
Installation
Install auto by-starter to the carburetor body. Screws × 2
Install fixing plate to the upper groove of auto
by-starter, and install its flat surface to carburetor.
Install screw and tighten it.
Cautions
Align the round point of the starter with the
screw hole of air intake side.
Fixing Valve
plate needle
4-7

Float Chamber
Float
Disassembly Float pin
Remove 4 mounting screws and then the float
chamber cover.
Remove the float pin and float valve.
Screws × 4
Checking
Check float needle valve and valve seat for drop
Drain bolt
difference damage, wear out, dirty or clogged.
Float needle
Cautions valve
In case of worn out or dirt, the float valve and

Float pin
valve seat will not tightly close causing fuel
level to increase and as a result, fuel flooding.
A worn out or dirty float valve must be Float
replaced with a new a new one.
Remove main jet, fuel needle jet holder, fuel Main jet
Slow jet
needle jet, slow jet, fuel amount adjustment Fuel needle
screw. holder
Fuel
Cautions needle jet
Fuel amount
y Take care not to damage jets and adjust adjustment screw
screw.
y Before removing adjustment screw, turn it
all the way down and note the number of
turns.
y Do not turn adjustment screw forcefully to
avoid damaging valve seat face.
Fuel needle jet Main jet

Clean jets with cleaning fluid.
Then use compressed air to blow dirt off.
Blow carburetor body passages with compressed
air.
Fuel needle holder
Slow jet
4-8
Installation
Install main jet, fuel needle jet seat, fuel needle
jet, slow speed jet and fuel amount adjustment
screw.
Cautions
Set the adjustment screw in according to Fuel amount
number of turns noted before it was adjustment screw
removed.
Install the float valve, float, and float pin.

Checking Fuel Level
Cautions
y Check again to ensure float valve, float for
proper installation.
y To ensure correct measurement, position
the float meter in such a way so that float
chamber face is vertical to the main jet.
Fuel level: 17.5 mm
Installation Of Carburetor
Install carburetor in the reverse order of removal.
Following adjustments must be made after
installation.
y Throttle valve cable clearance adjustment
y Idle speed adjustment Float meter
Idle Speed Adjustment

Caution Throttle valve
y Fuel amount adjust screw was set at stopper screw
factory, so no adjustment is needed. Note
the number of turns it takes to screw it all
the way in for ease of installation.
y Never screw in forcedly to avoid damaging
the screw seat.
y The main stand must be used to support
the motorcycle to perform the
Use a tachometer when adjusting engine RPM.

Screw in adjustment screw gently, then back up
Throttle valve cable
to standard turns. adjustment nut
Standard turns: 1 3/4±3/4 turns
Warm up engine, adjust throttle valve stopper
screw to standard RPM.
Idle speed rpm: 1700±100 rpm
Connect the sampling hose of exhaust analyzer
to exhaust front end. Press test key on the
analyzer.
Adjust the air volume adjustment screw and read
CO reading on the analyzer.
CO standard value: 1.0~1.5 %
Accelerate in gradual increments, make sure
both rpm and CO value are in standard values
after engine running in stable. If rpm and CO
value fluctuated, repeat the procedures
described above for adjusting to standard value. Air volume
adjustment screw
4-9
Fuel Tank
Removal of fuel unit.
Open the seat.
Remove the luggage box assembly. (bolt x 4,
screw x 1)
Remove the rear carrier. ( bolt x 4)
Remove both the left and right body covers.
(screw x 4, bolt x 2)
Remove the fuel unit coupler.
Fuel unit coupler
Turn the plastic cap in CCW direction and then

remove the fuel unit plastic cap.
Fuel unit plastic cap
Remove the fuel unit. Fuel unit
Caution
Do not bend the float arm.
Install in reverse order of removal procedures.

Remark: Aligning the slot of fuel unit with the ring
of fuel tank as installation.
4-10
Removal of fuel tank
Bolt x 3
Open the seat.
screw x 1)
Remove the body cover. (screw x 4)
Remove the rear lamp and rear fender assembly.
(screw x 4)
Bolt on each side x 1
Remove the fuel inlet. (bolt x 2)

Bolt x 2
Remove the fuel tank mounting bracket. (bolt x 4)
Bolt x 2
Bolt x 2
4-11
Loosen the fuel inlet clamper and then remove

the fuel vapor return hose.
Fuel vapor return hose
Remove the fuel hose and then remove the fuel

tank.
Caution
Be sure that the fuel in the fuel bank had been
drain out clearly before removing.
Fuel hose
Installation
Install the fuel tank in reverse procedure of
removal.
4-12
Air Cleaner
Remove the air cleaner cover. (screw x 6)
Screw x 6
Remove the air cleaner assembly.
Installation:
Install the air cleaner in reverse procedure of
removal.
Procedures for cleaning air cleaner element:

(sponge type only)
1.clean. 2.squeeze dry. 3.soak in engine oil. 4.squeeze dry
4-13
NOTE:
4-14
Home page Contents
5. REMOVAL OF ENGINE
Operational Precautions ........... 5-1 Engine Suspension Frame ........ 5-8

Engine Removal ......................... 5-2 Installation Of Engine ................ 5-9
Removal Of Engine
Suspension Bushing ................. 5-7
Operational Precautions
General Information
y Engine must be supported by a bracket or adjustable tool in height.
y The following parts can be serviced with the engine installed on the frame. 5
1. Throttle valve
2. Driving disk, driving belt, clutch, and transporting disk
3. Final reduction gear mechanism
Specification
Item Specification

Engine Oil Capacity
Disassemble 1000 c.c.

Gear Oil Capacity
Disassemble 110 c.c.
Torque Values
Engine suspension bolt (Frame side) 4.5~5.5 kgf-m
Engine suspension nut (engine side) 4.5~5.5 kgf-m
Bolt of rear shock absorber upper connection 3.5~4.5 kgf-m
Bolt of rear shock absorber lower connection 2.4~3.0 kgf-m
Bolt of rear brake clipper 2.9~3.5 kgf-m
Nut of rear wheel axle 11.0~13.0 kgf-m
Nut of exhaust connection 0.5~1.0 kgf-m
Bolt of exhaust fixed 3.0~3.6 kgf-m
Bolt of rear bracket 3.0~3.6 kgf-m
5-1
Engine Removal
Remove the battery cap (screw ×3).
Remove the battery negative (-) cable.
Remove the battery positive (+) cable.
Open the seat.

screw x 1)
Remove center cover. (screw x2)
Remove rear carrier and fuel tank cap.
(hex-socket bolt x 4)
Remove both left & right body covers and center
upper cover set. (screw x 4)
Remove both left & right side covers. (screw x4)
Remove both left & right pedals. (screw x 8)
Remove the connector of rear lamp power wire

and generator wire.
Remove the starter motor cable on the relay. Starter motor cable
5-2
Remove the spark plug.

Remove the engine temperature sensor
connector.
Caution
Open the latch located under the temperature

sensor before disconnect it so that the
connector can be pull out and not be
damaged.
Spark plug cap
Loose the throttle valve cable fixed nut and

remove the throttle valve cable.
Throttle valve cable

fixed nut
Remove fuel hose, vacuum hose. Auto by-starter
Vacuum hose Fuel hose
Disconnect auto by-starter line coupler.
Auto by-starter line
5-3
Loosen the clamp of the air cleaner duct, and

Inlet pipe clamp
then remove the duct.
Loosen the clamp of the inlet pipe, and then
remove the carburetor.
Air cleaner duct clamp
Remove the kick starter arm.(bolt×1)

Remove the engine left cover protecting cover.
(screw×3)
Loosen the clamp of the engine left cover air Bolt ×2

duct, and then remove the duct.
Remove the air cleaner fixed bolt. (blot×2)
Engine left cover duct clamp
Remove the front-end nuts of exhaust muffler. Nut x2

(Nut ×2)
5-4
Remove the rear-end bolts of exhaust muffler.

(Bolt ×3)
Remove the exhaust muffler.
Bolt x 3
Remove the rear wheel and muffler rear bracket.

(nut x 1)
Nut ×1
Remove the rear brake adjustment nut.
Rear brake adjustment nut
Engine suspension removal

Remove the rear shock absorber lower bolt.
(bolt x 1)
Bolt x 1
5-5
Remove the side hole cap of cooling fan. Side hole cap
Remove the engine suspension nuts, and then

remove the bolt from the side hole.
Caution
With a bracket to support the engine to

prevent from it damage by falling down as
removing the engine.
Nut x 1
Check if the engine suspension, rear shock

absorber bushing, and cushion rubber for
damage. Replace them with new ones if so.
5-6
Removal Of Engine Suspension
Bushing
If engine suspension frame and the cushion
rubber of rear shock absorber bushing damaged.
Then, with the bushing remover / pressor,
Ø 28mm & Ø 20mm, to press the bushing out,
and replace it with new one.
Engine suspension bushing: Ø 28mm

Rear shock absorber bushing: Ø 20mm
Pressing out
Place the detent section of the bushing remover
toward the bushing, and drive both the pressing
ring and bolt in to press the bushing out.
Pressing In
Place the flat section of the remover toward the
bushing, and then drive the bushing, pressing
ring, and bolt in to install the bushing.
5-7
Engine Suspension Frame
Removal
Remove the right side bolt of engine suspension
frame.
Engine suspension
bolt (right side)
Remove the left side bolt of engine suspension

frame.
Engine suspension
bolt (left side)
Check if the engine suspension frame bushing

and cushion rubber for damage. If so, replace
with new ones.
Installation
Tighten the bolts and nuts of engine suspension
frame.
Engine suspension frame nut:

5-8
Installation Of Engine
Check if the bushings of engine suspension
frame and shock absorber for damaged. If so,
replace with new ones.
Install the engine according to the reversing
order of removal.
Caution
y Note both feet and hands safety for
squeezing as engine installation.
y Do not bent or squeeze each wires or hose. Nut x 1
y Route all cables and wires in accordance
with the routine layout.
Engine suspension nut:

Rear shock absorber bolt:

Torque Value: Top: 3.5~4.5 kgf-m
Down: 2.4~3.0 kgf-m
Rear wheel axle nut: Nut x1

5-9
NOTE:
5-10
Home page Contents
6. Cylinder Head/Valve
Mechanism Illustration...............6-1 Valve Stem Replacement .......... 6-9

Precautions In Operation...........6-2 Valve Seat Inspection And Service
.................................................. 6-10
Troubleshooting .........................6-3
Cylinder Head Reassembly .... 6-12
Cylinder Head Removal .............6-4
Cylinder Head Installation ...... 6-14
Cylinder Head Disassembly ......6-6
Valve Clearance Adjustment .. 6-16
Cylinder Head Inspection ..........6-7
6
1.0~1.4 kgf-m
0.7~1.1 kgf-m
1.0~1.2kgf-m
2.0~2.4kgf-m
1.0~1.4kgf-m
0.8~1.2kgf-m
1.0~1.4kgf-m
6-1
General Information
• This chapter is contained maintenance and service for cylinder head, valve, and camshaft as well
as rocker arm.
• Cylinder head service cannot be carried out when engine is in frame.
Specification Unit: mm
Item Standard Limit
Compression pressure 12 ± 2 kg/cm² -
Intake 25.688 25.290

Camshaft Height of cam lobe
Exhaust 25.519 25.120
Rocker ID of valve rocker arm 12.000~12.015 12.100

arm
OD of valve rocker arm shaft 11.966~11.984 11.910
Intake 4.975~4.990 4.900

OD of valve stem
Exhaust 4.950~4.975 4.900
Guide seat 5.000~5.012 5.030
Clearance between Intake 0.010~0.037 0.080

Valve
valve stem and guide
Exhaust 0.025~0.062 0.100
Free length of valve spring 35.000 31.500
Valve seat width 1.000 1.600
Connection Flatness of cylinder head - 0.050
Torque Value
Cylinder head bolt 1.0~1.4kgf-m
Cylinder head bolt (LH) 1.0~1.4kgf-m
Cylinder head Nut 1.8~2.2kgf-m (apply with oil on bolt thread & seat)
Sealing bolt of timing chain auto-tensioner 0.8~1.2kgf-m
Bolt of timing chain auto-tensioner 1.0~1.4kgf-m
Timing gear cover bolts 0.7~1.1kgf-m (apply with oil on bolt thread & seat)
Spark plug 1.0~1.4kgf-m
Tools
Valve reamer: 5.0mm
Valve guide driver: 5.0mm
Valve spring compressor
6-2
Troubleshooting
Engine performance will be effected by troubles on engine top-end. The troubles usually can be
determinated or by performing cylinder compression test and judging the abnormal noise generated.
Rough Idle
• Low compression pressure
Low compression pressure

1. Valve
z Improper valve adjustment
z Burnt or bended valve
z Improper valve timing
z Valve spring damaged
z Valve carbon
z Poor sealing on valve seat
z Improper spark plug installation
2. Cylinder head
z Cylinder head gasket leaking or damage
z Tilt or crack cylinder surface
3. Piston
z Piston ring worn out
High compression pressure

• Too much carbon deposit on combustion chamber or piston head
Noise
• Improper valve clearance adjustment
• Burnt valve or damaged valve spring
• Camshaft wear out or damage
• Cam chain wear out or looseness
• Auto-tensioner wear out or damage of cam chain
• Camshaft sprocket wear out
• Rocker arm or rocker arm shaft wear out
White smoke
• Valve guide or valve stem wear out
• Valve stem seal wear out
6-3
Cylinder Head Removal Bolt x 2
Remove:
Remove the cooling fan cover. (screw x 2, bolt x
2)
Screw x 2
Remove the right cover of engine. (screw x 4)

Up Down
Screw x 2 Screw x 2
Remove the left cover of engine. (screw x 4)
Bolt x 1
Remove the left cap bolt of cylinder head (bolt

x2), and then remove the left cap of cylinder
head.
Remove the spark plug.
Bolt x 2
6-4
Turn the flywheel in counter clockwise motion

with T type wrench until the “T” mark on flywheel
aligned with the mark on the crankcase so that
the hole on the camshaft sprocket is forward up
and piston is at TDC position.
BTDC
Loosen the screw cap of camshaft chain

tensioner and remove O-ring.
With a flat screwdriver to tighten the screw of
camshaft chain tensioner in a clockwise motion
for release tensioner.
Remove the cam sprocket. (bolt x2)
Bolt x 2
Remove the left bolt (bolt x2) of cylinder head Nut x 4 Bolt x 2
firstly, and then remove the 4 nuts & washers
from the cylinder head top-end.
Pry out the chain and take out the sprocket.
Then, remove the cylinder head.
Caution
• Loosen the nuts diagonally by 2-3
sequences.
• Do not let the chain fall into the crankcase
after removed the sprocket.
6-5
Cylinder Head Disassembly
Remove the adjustment hole cap for the EX & IN
valve clearance. (bolt x 6)
Adjustment
hole cap
Firstly, remove the camshaft stopper, and then Stopper

drive a 6mm bolt into camshaft. Finally, remove
the camshaft and rocker arm.
Camshaft
Use a valve compressor to press the valve

spring.
After removed valve split locks, release the
Valve split lock
compressor and then take out spring retainer,
valve spring and valves.
Caution
In order to avoid loosing spring elasticity, do
not press the spring too much. Thus, press
length is based on the valve split locks in
which can be removed.
Special Service Tool: Valve spring compressor

Or with the valve spring remover/installer to
compress the valve spring directly. Then, remove
the valve and valve spring.
Caution
In order to avoid damaging the valve stem
and the cylinder head, in the combustion
chamber place a rag between the valve
spring remover/installer as compressing the
valve spring directly.
Special Service Tool: Valve spring remover/

installer.
6-6
Remove valve, valve stem and valve spring.
Cylinder Head Inspection

Camshaft
Inspect cam lobe height for damaged.
Service Limit:
IN: Replacement when less than 25.29mm
EX: Replacement when less than 25.12mm
Inspect the camshaft bearing for looseness or
wear out. If any, replace whole set of camshaft
and bearing.
Rocker Arm
Measure the cam rocker arm I.D.
Service Limit: Replace when it is less than
12.10 mm.
Rocker Arm Shaft

Measure the active O.D. of the cam rocker arm
shaft and cam rocker arm.
11.91 mm.
Calculate the clearance between the rocker arm

shaft and the rocker arm.
0.10 mm.
6-7
Remove cylinder head gasket and 2 lock pins. Lock pin

Remove chain plate.
Clean up residues from the matching surfaces of
cylinder and cylinder head.
Caution
• Do not damage the matching surfaces of
cylinder and cylinder head.
• Avoid residues of gasket or foreign
materials falling into crankcase as
cleaning.
Chain plate
Cylinder head gasket
Remove valve stem guide seal.

Clean carbon deposits in combustion chamber.
Clean residues and foreign materials on cylinder
head matching surface.
Caution
Do not damage the matching surface of
cylinder head.
Cylinder Head
Check if spark plug and valve holes are crack.
Measure cylinder head plane with a straightedge
and flat feeler gauge.
Service limit: 0.5 mm
Valve Spring Free Length

Measure the free length of intake and exhaust
valve springs.
6-8
Valve Stem
Check if valve stems are bend, crack or burn.
Check the operation condition of valve stem in
valve guide, and measure & record the valve stem
outer diameter.
Service Limit: IN→4.90 mm
EX→4.90 mm
Valve Guide
Caution
Before measuring the valve guide, clean
carbon deposits with reamer.
5.0mm valve guide
Special Service Tool: 5.0mm valve guide reamer reamer
Measure and record each valve guide inner
diameters.
The difference that the inner diameter of valve
guide deducts the outer diameter of valve stem is
the clearance between the valve stem and valve
guide.
Service Limit: IN→0.08 mm
EX→0.10 mm
Caution
If clearance between valve stem and valve
guide exceeded service limit, check whether
the new clearance that only replaces new
valve guide is within service limit or not. If
so, replace valve guide.
Correct it with reamer after replacement.

If clearance still exceeds service limit after
replaced valve guide, replace valve stem too.
Caution
It has to correct valve seat when replacing
valve guide.
Valve Stem Replacement 5.0mm valve

Heat up cylinder head to 100~150℃ with heated guide driver
plate or toaster.
Caution
• Do not let torch heat cylinder head
directly. Otherwise, the cylinder head may
be deformed as heating it.
• Wear on a pair of glove to protect your
hands when operating.
6-9
Hold the cylinder head, and then press out old
valve guide from combustion chamber side.
13 mm Valve guide driver
Tool: Valve guide driver: 5 mm
5.0mm
(0.15in)
Caution
• Check if new valve guide is deformation
after pressed it in.
• When pressing in the new valve guide,
cylinder head still have to be kept in
100~150℃.
Adjust the valve guide driver and let valve guide
height is in 13mm.
Press in new valve guide from rocker arm side.
Tool: Valve guide driver: 5 mm
Wait for the cylinder head cooling down to room
temperature, and then correct the new valve
guide with reamer.
Caution Valve guide reamer
5.0mm
• Using cutting oil when correcting valve
guide with a reamer.
• Turn the reamer in same direction when it
be inserted or rotated.
Correct valve seat, and clean up all metal

residues from cylinder head.
Tool: Valve guide reamer 5 mm
Valve Seat Inspection And Service

Clean up all carbon deposits onto intake and
exhaust valves.
Apply with emery slightly onto valve contact face.
Grind valve seat with a rubber hose or other
manual grinding tool.
Caution
• Do not let emery enter into between
valve stem and valve guide.
• Clean up the emery after corrected, and
apply with red paint onto contact faces of
valve and valve seat.
Remove the valve and check its contact face.

Caution
• Replace the valve with new one if valve Valve seat

seal is roughness, wear out, or width
incomplete contacted with valve seat.
• If the valve and the valve seat still can
not be matched sealing after grinded,
replace it with new one.
6-10
Valve Seat Inspection
If the valve seat is too width, narrow or rough,
correct it. Roughness
Valve seat width
Check the contact condition of valve seat.
Valve Seat Grinding
The worn valve seat has to be grinded with valve
seat chamfer cutter. 45°
Use 45° valve seat chamfer cutter to cut any
rough or uneven surface from valve seat.
Caution
After valve guide had been replaced, it has

to be grinded with 45° valve seal chamfer
cutter to correct its seat face.
Old valve seat width
Use 32° cutter to cut a quarter upper part out.
32°
Use 60° cutter to cut a quarter lower part out.

Remove the cutter and check new valve seat.
Old valve seat width
60°
Use 45° cutter to grind the valve seat to specified

width.
1.0mm
Caution
Make sure that all roughness and uneven
faces had been grinded.
Grind valve seat again if necessary.
45°
6-11
Coat the valve seat surface with red paint.
Install the valve through valve guide until the Contact surface
valve contacting with valve seat, slightly press too high
down the valve but do not rotate it so that a seal
track will be created on contact surface. Old valve seat
width
Caution
The contact surfaces of valve and valve seat 32°
are very important to the valve sealing
capacity.
If the contact surface too high, grind the valve

seat with 32° cutter.
Then, grind the valve seat to specified width.
If the contact surface too low, grind the valve seat Contact surface
Old valve seat
too low
with 60° cutter. width
Then, grind the valve seat to specified width.
60°
After the valve seat grinded, coat valve seat

surface with emery and then slightly press the
grinded surface.
Clean up all emery coated onto cylinder and
valve after grinded.
Cylinder Head Reassembly Valve stem

Valve split oil seal
Lubricate valve stem with engine oil, and then locks
insert the valve into valve guide.
Install new valve stem oil seal. Spring
Install valve springs and retainers. retainer
Caution
Valve
The closed coils of valve spring should face
down to combustion chamber.
Valve spring
6-12
Use valve spring compressor to press valve
spring.
Install valve split locks and release the valve
compressor.
Caution
In order to avoid loosing spring elasticity, do
not press the spring too much. Thus, press
length is based on the valve split locks in
which can be removed.
Special Service Tool: Valve spring compressor
Or with the valve spring remover/installer to

install valve and spring.
Firstly, install valve spring, retainers onto the
valve as assembling.
Caution
In order to avoid damaging the valve stem
and the cylinder head, in the combustion
chamber place a rag between the valve
spring remover/installer as compressing the
valve spring directly.
With the valve spring remover/installer, compress

the valve spring directly. Then, remove the valve
and valve spring.
Special Service Tool: Valve spring remover/

installer.
Tap valve stem to make valve retainer and valve

stem sealing properly.
Caution
Place and hold cylinder head on to working

table and place a rag against onto the valve
so that can prevent damage valve stem and
cylinder head.
6-13
Install the camshaft onto the cylinder head and EX rocker arm shaft Lock plate
then the rocker arm and the rocker arm shaft.
Lock the lock plate after rotate the rocker arm
shaft to properly position.
Caution
There is different shapes on the top-end of
rocker arm shaft. The machined surface on
the rocker arm shaft has to face toward
exhaust side, and then the larger surface
has to align with the bolt hole of cylinder
h d IN rocker arm shaft
Lock pins
Cylinder Head Installation
Install the lock pins and new cylinder head
gasket onto the cylinder head.
Install the camshaft chain plate.
Chain plate
Cylinder head gasket
Install the cylinder head. Nut x 4 Bolt x 2

Tighten the 4 nuts onto the cylinder head top-end,
and then the 2 cylinder head mounting bolts on
its side.
Caution
This model is equipped with precious 4
valves mechanism so tighten torque can not
be over the limited value and tightening the
bolts diagonally by 2-3 sequences. It can
prevent from cylinder head deformation and
then cause noise or leaking problems so that
effect motorcycle’s performance.
With T type wrench to turn crankshaft in a

clockwise motion so that the “T” mark on the
alternator flywheel aligns with the mark on
crankcase. (piston is at TDC position)
Place the TDC marks of the cam sprocket at
same level of the top-end of cylinder head. The
other single hole of the cam sprocket is in
upward. Then, install the cam chain onto the
cam sprocket.
Install the spark plug and tighten it.

Torque value: 1.0~1.2 kgf-m BTDC
6-14
Tighten the cylinder head right side cover. (bolt x

2)
Bolt x 2
With flat screwdriver, turn the cam sprocket

tensioner in counter-clockwise motion so that the
tensioner is pushed out to contact the cam chain
plate tightly. Apply with oil onto a new O-ring
and then install it onto the tensioner hole.
Tighten the bolt cap of the tensioner adjustment
hole.
Caution
The O-ring must be installed into glove.
Install the left-side cover of the engine body. (bolt

x 1)
Bolt x 1
Install the right-side cover of the engine body. Up Down

(screw x 4)
Screw x 2 Screw x 2
6-15
Install the cooling fan cover. (screw x2, bolt x 2) Bolt x 2
Screw x 2
Valve Clearance Adjustment

Loosen valve clearance adjustment nuts and
bolts located on valve rocker arm.
Measure and adjust valve clearance with feeler
gauge.
After valve clearance had been adjusted to
standard value, hold adjustment bolt and then
tighten the Adjustment nut.
Standard Value: IN 0.12 ± 0.02 mm
EX 0.12 ± 0.02 mm
Install the valve clearance adjustment hole cap.
(bolt x2)
Start the engine after assembly. Remove the

intake valve adjustment hole cap and make sure
that engine oil flows onto the cylinder head.
Stop the engine after confirmed, and then install
the intake valve adjustment hole cap.
Install the seat cushion and the central cover.
Caution
• The cylinder components will be serious
wear out if lubricant did not flow onto the Intake valve
cylinder head. So it has to be adjustment hole cap
confirmed.
• It has to be in idle speed when conduct
this procedure. Never increase engine
speed in high RPM.
6-16
Home page Contents
7. Cylinder/Piston
Mechanism Illustration ...............7-1 Piston Removal ...........................7-5

Precautions In Operation ...........7-2 Piston Inspection ........................7-5
Trouble Diagnosis.......................7-2 Piston Ring Installation ..............7-7
Cylinder Removal........................7-3 Piston Installation .......................7-8
Cylinder Inspection.....................7-4 Cylinder Installation....................7-8
7
0.8~1.2 kgf-m
7-1
This Chapter Contents
7. Cylinder/Piston
General Information
Both cylinder and piston service cannot be carried out when engine mounted on frame.
Item Standard Limit
ID 52.400~52.410 52.500
Bend/wrapage － 0.050
Cylinder
Cylindrical roundness － 0.050
Cylindrical roundness － 0.050
Top ring 0.025~0.060 0.090

Clearance between
piston rings
2nd ring 0.015~0.050 0.090
Top ring 0.100~0.250 0.500
Ring-end gap 2nd ring 0.250~0.400 0.650
Piston/Piston Oil ring side

0.200~0.800 －
ring rail
OD of piston 52.370~52.390 52.300
Lower-end up 9mm
Piston OD measurement position －
of piston skirt
Clearance between piston and
0.010~0.040 0.100
cylinder
ID of piston pin boss 15.002~15.008 15.040
OD of piston pin 14.994~15.000 14.960
Clearance between piston and piston pin 0.002~0.014 0.020
ID of connecting rod small-end 15.016~15.034 15.060
Trouble Diagnosis
Low Or Unstable Compression Pressure Smoking in Exhaust Pipe
• Cylinder or piston ring worn out • Piston or piston ring worn out
• Piston ring installation improperly
• Cylinder or piston damage
High Compression Pressure
• Carbon deposit onto the piston & combustion
Engine Overheat
chamber
• Carbon deposits on cylinder head top side
Knock or Noise
• Cylinder or piston ring worn out
• Carbon deposits on cylinder head top-side
• Piston pin hole and piston pin wear out
7-2
7. Cylinder/Piston
Cylinder Removal
Remove cylinder head. (refer to chapter 6)
Remove 2 bolts and then take out the cam chain
auto-tensioner.
Bolt x 2
Remove cam chain plate.

Remove cylinder.
Remove cylinder gasket and lock pins.
Clean the residues attached onto the matching

surfaces of cylinder and crankcase.
7-3
7. Cylinder/Piston
Cover the holes of crankcase and cam chain with
a piece of cloth.
Clean up all residues or foreign materials from
the two matching surfaces of cylinder and
crankcase.
Caution
To soap the residues into solvent so that the
residues can be removed more easily.
Cylinder Inspection Exhaust side Intake side

Check if the inner diameter of cylinder is worn
out or damaged.
In the 3 positions (top, center and bottom) of Top
cylinder, measure the X and Y direction values
respective in the cylinder. Center
Calculate both the real roundness (the difference Bottom
between X and Y motion values) and the
cylindrical roundness (the difference in the top,
center or bottom positions of X or Y motion
values.) Then, determinate by the max. value.
Service limit:
Real roundness: correct or replace as over
0.05 mm
Cylindrical roundness: correct or replace as
over 0.05 mm
Check Cylinder Wrapage.

Service limit: correct or replace as over 0.05
mm
7-4
7. Cylinder/Piston
Piston Removal
Plug crankcase opening with a cleaning cloth to
prevent from piston pin snap ring or other parts
falling into crankcase when disassembling.
Hold another snap ring with pliers.
Push out the piston pin from the side that not
removed the snap ring.
Remove piston rings.
Caution
Pay attention to remove piston rings because
they are fragile.
Disassemble the piston rings.

Check if the piston rings are damaged or its
grooves are worn.
Clean out the carbon deposit around the
piston ring groove.
Piston Inspection Piston ring

Install the piston rings and then measure
clearance between piston ring and its grooves.
Service Limit: Push in
Top ring: replace if over 0.09 mm
2nd ring: replace if over 0.09 mm
Piston
Feeler gauge
Take out the piston rings and place them

respective into cylinder below 20mm of cylinder
top. Measure each piston ring gaps.
Caution
Push the piston rings into cylinder with
piston top-end in parallel motion.
Service Limit:
Top ring: replace if over 0.5 mm Piston rings
2nd ring: replace if over 0.65 mm
7-5
7. Cylinder/Piston
Measure the outer diameter of piston pin.
Service Limit: 14.96 mm
Measure the inner diameter of connecting rod

small end.
Measure the inner diameter of piston pin hole.

Calculate clearance between piston pin and its

hole.
Measure piston outer diameter.

Caution
The measurement position is 10 mm
distance from piston bottom side, and 90° to
piston pin.

Compare measured value with service limit to
calculate the clearance between piston and
cylinder.
7-6
7. Cylinder/Piston
Piston Ring Installation
Clean up piston top, ring groove, and piston shirt.
Install the piston ring onto piston carefully.
Place the openings of piston ring as diagram shown.
Caution
• Do not damage piston and piston rings as installation.
• All marks on the piston rings must be forwarded to up side.
• Make sure that all piston rings can be rotated freely after installed.
Top ring
2nd ring
120°
Side
ring
Spacer Oil ring
Side
ring
Over 20 mm
Top groove
2nd groove
Oil groove
7-7
7. Cylinder/Piston
Piston Installation
Install piston and piston pin, and place the IN
marks on the piston top side forward to intake
valve.
Install new piston pin snap ring.
Caution
• Do not let the opening of piston pin snap ring
align with the opening piston ring.
• Place a piece of cloth between piston skirt
section and crankcase in order to prevent
snap ring from falling into crankcase as
operation.
Cylinder Installation
Clean up all residues and foreign materials on
the matching surface of crankcase. Pay
attention to not let these residues and foreign
materials fall into crankcase.
Caution
To soap the residues into solvent so that the
residues can be removed more easily.
Install 2 lock pins and new gasket.
Coat engine oil to inside of cylinder, piston and

piston rings.
Care to be taken when installing piston into
cylinder. Press piston rings in one by one as
installation.
Caution
Do not push piston into cylinder forcefully
because this will cause the piston and the
piston rings to be damaged.
Install the cam chain plate, the cylinder gasket

and lock pins.
Install cylinder head. (refer to Chapter 6)
Install the cam chain auto-tensioner. (2 bolts)
Bolt x 2
7-8
Home page Contents
8. V-Belt Driving System/Foot Starter
Mechanism Illustration ............. 8-1 Foot Starter.................................8-3

Maintenance Description.......... 8-2 Drive Belt ....................................8-4
Trouble Diagnosis ..................... 8-2 Movable Drive Face ...................8-6
Left Crankcase Cover ............... 8-3 Clutch / Driven Pulley ................8-9
5.0~6.0 kgf-m
5.0~6.0 kgf-m
5.0~6.0 kgf-m
1.0~1.5 kgf-m
8-1
Maintenance Description
PRECAUTIONS IN OPERATION
• Driving pulley, clutch, and driven pulley can be serviced on the motorcycle.
• Driving belt and driving pulley surface must be free of grease.
Item Standard value Limit
Driving belt width 19.500 18.500
ID of sliding pulley bushing 27.000~27.021 27.060
OD of sliding pulley hub 26.970~26.990 26.940
OD of weight roller 19.950~20.100 19.500
ID of clutch jacket 130.000~130.200 130.500
Thickness of clutch lining 4.000~4.100 2.000
Free length of driving pulley spring 128.400 123.400
OD of driving pulley 33.965~33.985 33.940
ID of sliding pulley 34.000~34.025 34.060
ID: Inner Diameter
OD: Outer diameter
Torque value Special Service Tools

Sliding pulley nut: 5.0~6.0 kgf-m Clutch spring compressor
Clutch jacket nut: 5.0~6.0 kgf-m Bearing puller (inner type)
driving pulley nut: 5.0~6.0 kgf-m Clutch mounting nut wrench
Universal fixture
Trouble Diagnosis
Engine can be started but motorcycle can Insufficient horsepower or poor high speed
not be moved performance
1. Worn driving Belt 1. Worn driving belt
2. Worn tilt plate 2. Insufficient spring capacity of driven pulley
3. Worn or damaged clutch lining 3. Worn roller
4. Broken driven pulley 4. Driven pulley operation un-smoothly
Shudder or misfire when driving

1. Broken clutch lining
2. Worn clutch lining
8-2
Left Crankcase Cover
Removal of Crankcase Cover
Remove body cover.
Remove foot starter lever. ( bolt x 1)
Remove the outer cover of engine left-side cover.
(screw x 3)
Loosen vent strap on the front-left side of cover,
and then remove the vent.
Remove air cleaner. (bolt x 2)
Remove the engine left-side cover. ( bolt x 8)
Outer cover screw x 3
Foot Starter
Disassembly
Remove snap ring and thrust washer from
engine left-side cover.
Install foot starter lever, rotate the lever slightly
and then remove driving gear and washer.
Remove the lever, foot starter, starter shaft, and
return spring as well as socket.
Inspection
Check if starter shaft, driving gear, socket and
bearing hole for wear or damage. Replace it with
new one if necessary. Starter shaft Return spring Driving gear
Check the return spring and friction spring for
spring force or damaged. Replace it with one if
poor parts found.
Reassembly
Install socket, return spring and starter shaft as
diagram shown.
Install thrust washer and snap ring onto starter
shaft.
Install foot starter lever temporary.
Rotate the lever and then align driving gear with
width-tooth on the starter shaft.
Install the friction of driving gear onto convex part
of the cover.
Installation of the left crankcase cover
Install the left crankcase cover. (8 screws)
Install front vent tube of left cover and tighten the
strap. Return
Starter
Install foot starter lever. (1 bolt) spring
shaft
Tighten the air cleaner. (2 bolts)
Install the body cover.
Friction
spring
8-3
Drive Belt
Removal
Remove left crankcase cover.
Hold drive face with universal fixture, and remove
nut and drive face.
Universal
fixer
Hold the clutch outer with the universal fixture,

Nut
and the remove the nut and the clutch outer .
Caution
Using special service tools for tightening or
loosening the nut. Fixed rear wheel or rear
brake only will damage reduction gear
system.
Universal
fixer
Push the drive belt into belt groove as diagram

Drive belt
shown so that the belt can be loosened, and then
remove.
Drive belt and clutch at same time.
Inspection
Check the drive belt for crack or wear. Replace
it if necessary. Tooth
Measure the width of drive belt as diagram Width
shown. Replace the belt if exceeds the service
limit.
Caution
• Using the genuine parts for replacement.
• The surfaces of drive belt or pulley must
be free of grease.
8-4
Installation
Pull out the driven face and then insert the drive
belt into the driven pulley.
Sliding
Caution driven
Pull out sliding driven face and then insert face
the drive belt into the driven pulley so that
the drive belt set can be installed onto pulley
more easily.
Install the clutch set with drive belt onto the drive
shaft.
The other end of belt hook onto the movable drive
face.
Install the clutch outer.
Clutch outer
Install the clutch with universal fixture, and then
tighten nut to specified torque value.
Nut
Universal fixer
Caution
When install the driving belt, if there is a
arrow mark, then the arrow mark must point
to rotation motion. If not, the letters on the
belt must be forwarded to assembly
direction.
8-5
Movable Drive Face
REMOVAL
Remove left crankcase cover.
Hold drive face with universal fixture, and then
remove drive face nut.
Remove drive face.
Universal
fixture
Take out the drive belt from the drive face.

Movable drive face
Remove movable drive face set and drive face
boss from crankshaft.
Drive face
Crankshaft
boss
Remove ramp plate.
Ramp
plate
Remove weight rollers from movable drive face.

Movable drive face
Weight roller
8-6
Inspection
The operation of movable drive face is means of
the weight roller to pressing on it with centrifuge Weight roller
force. And then the speed is changed by the
ramp plate rotation. Thus, if weight rollers are
wear out or damage, the centrifuge force will be
effected.
Check if rollers are wear out or damage.
Replace it if necessary.
Measure each roller’s outer diameter. Replace it
if exceed the service limit.
Check the drive face boss if damaged or wear

Movable drive face
out. Replace it if necessary.
Measure the drive face boss’s outer diameter.
Replace it if exceed the service limit.
Service limit: 23.94 mm Drive face boss
Measure the drive face boss’s inner diameter.
Replace it if exceed the service limit.
Assembly/Installation Weight roller

Install the weight roller.
Caution
The both ends of weight roller are different.
In order to prolong the roller life span and
prevent abnormal wearing out, install the
closed end onto the movable drive face in
the movement of CCW.
Closed end
Install the ramp plate slide pieces (3 pieces) onto Slide

pieces
the ramp plate.
Install the ramp plate.
Ramp plate
8-7
Apply with grease 4~5 g to inside of drive face
boss hole, and install drive face boss.
Caution
The pulley surface has to be free of grease.
Clean it with cleaning solvent.
Pulley surface
Install movable drive face assembly onto Movable drive face

crankshaft.
Drive face
Crankshaft
boss
MOVABLE DRIVE FACE INSTALLATION Press down

Press drive belt into movable drive face, and
then press down the up & down sides of the drive
belt to separate it away from the drive face boss.
Caution
To press down the up & down sides of the
drive belt can avoid to pressing and
damaging the belt when installing the drive
face, and also can make sure that the drive
face can be tighten. Drive belt
Install drive face, washer and nut.
Caution
Make sure that two sides of pulley surfaces
have to be free of grease. Clean it with
cleaning solvent.
Hold drive face with universal fixture.

Tighten nut to specified torque.
Install left crankcase cover.
Universal fixture
8-8
Clutch / Driven Pulley Special nut wrench
DISASSEMBLY
Remove drive belt and clutch / driven pulley.
Install clutch spring compressor onto the pulley
assembly, and operate the compressor to let nut
be installed more easily.
Caution
Do not press the compressor too much.
Hold the clutch spring compressor onto bench

vise, and then remove mounting nut with special Clutch spring compressor
nut wrench.
Release the clutch spring compressor and
remove clutch and spring from driven pulley.
Remove oil seal collar from driven pulley.
Oil seal collar
Remove guide pin, guide pin roller, and sliding

driven face, and then remove O-ring & oil seal Sliding driven face Guide pin
Oil seal
seat from sliding pulley.
Guide pin
O-ring Guide pin roller
INSPECTION
Clutch outer
Measure the inner diameter of clutch outer
friction face. Replace the clutch outer if exceed
service limit.
Inner
diameter
Clutch outer
8-9
Clutch lining
Measure each clutch lining thickness. Replace Clutch lining
it if exceeds service limit.
Clutch
Driven pulley spring

Measure the length of driven pulley spring.
Replace it if exceeds service limit.
Driven pulley
Check following items:
y If both surfaces are damage or wear. Free length
y If guide pin groove is damage or wear.
y Replace damaged or worn components.
y Measure the outer diameter of driven surface
and the inner diameter of driven pulley.
Replace it if exceeds service limit.
Service limit: Outer diameter 33.94 mm
Inner diameter 34.06 mm Driven face
Driven Pulley Bearing Inspection

Check if the inner bearing oil seal is damage.
Check if needle bearing is damage or too big
clearance. Replace it if necessary.
Rotate the inside of inner bearing with fingers to
check if the bearing rotation is in smooth and Guide pin
silent. Also check if bearing outer is installed Sliding pulley groove
properly. Replace it if necessary.
Needle bearing
Outer ball
bearing
8-10
Clutch Block Replacement Spring
Remove snap and washer, and the remove Driving
clutch block and spring from driving plate. plate
Check if spring is damage or insufficient
elasticity.
Snap ring
Clutch block
Check if shock absorption rubber is damage or Shock absorption

deformation. Replace it if necessary. rubber
Apply with grease onto setting pins.
Setting pin
Apply with grease onto setting pins. But, the Shock absorption
clutch block should not be greased. If so, replace rubber
it.
Install new clutch block onto setting pin and then
push to specified location.
Caution
• Grease or lubricant will damage the clutch
block and effect the block’s connection
capacity.
Clutch block
Install the spring snap into groove with pliers.

Spring
8-11
Install snap ring and mounting plate onto setting
pin.
Snap ring
REPLACEMENT OF DRIVEN PULLEY BEARING

Remove inner bearing. Oil seal
Caution Outer bearing
• If the inner bearing equipped with oil seal

on one side in the driven pulley, then
remove the oil seal firstly.
• If the pulley equipped with ball bearing, it
has to remove snap ring and then the
bearing.
Snap ring Inner needle

bearing
Remove snap ring and then push bearing

forward to other side of inner bearing.
Place new bearing onto proper position and its
sealing end should be forwarded to outside.
Apply with specified grease. Recommended to
use the KING MATE G-3. Snap
Install the snap ring and hold the bearing. ring
Specified oil Outer

Sealing bearing
end
Install a new inner bearing.
Caution Sealing end
• Its sealing end should be forwarded to

outside as bearing installation.
• Install needle bearing with hydraulic
presser. Install ball bearing by means
of hydraulic presser.
Align oil seal lip with bearing, and then install the Inner bearing
new oil seal. (if necessary)
8-12
INSTALLATION OF CLUTCH/DRIVEN PULLEY Oil seal
ASSEMBLY
Install new oil seal and O-ring onto sliding driven
face. Apply with specified grease to lubricate
the inside of sliding driven face.
Specified
O-ring grease
Install sliding driven face onto driven face.

Install guide pin and guide pin roller. Sliding driven face Oil seal Guide pin
Guide pin
O-ring Guide pin roller
Install oil seal collar.

Oil seal collar
Install driven pulley spring and clutch into clutch

Mounting nut wrench
spring compressor, and press down the
assembly by turning manual lever until mounting
nut that can be installed.
Hold the compressor by bench vise and tighten
the mounting nut to specified torque with special Mounting
nut wrench. nut
Remove the clutch spring compressor.
Install clutch/driven pulley and driving belt onto
driving shaft.
Clutch spring compressor
8-13
NOTE:
8-14
Home page Contents
9. Final Driving Mechanism
Mechanism Illustration .............. 9-1 Inspection Of Final Driving

Mechanism..................................9-3
Operational precautions............ 9-2
Bearing Replacement.................9-4
Trouble Diagnosis...................... 9-2
Re-Assembly Of Final Driving
Disassembly of Final Driving Mechanism .................................9-6
Mechanism ................................. 9-3
Final driving
Countershaft shaft
Final driving gear

9
0.8~1.2 kgf-m
Countershaft
gear
Driving gear
2.0~2.4 kgf-m
1.0~1.4 kgf-m
9-1
Operational precautions
Specification Torque value
Application gear oil: 4-stroke lubricant Gear box cover 2.0~2.4 kgf-m
Recommended oil: KING MATE serial gear oils Gear oil drain plug 1.0~1.4 kgf-m
Oil quantity: 110 c.c. (100 c.c. when replacing) Gear oil filling bolt 0.8~1.2 kgf-m
Tools
Inner type bearing puller
Outer type bearing puller
Gear box oil seal installer
Gear box bearing installer
Trouble Diagnosis
Engine can be started but motorcycle can Gear oil leaks
not be moved • Excessive gear oil
• Damaged driving gear • Worn or damage oil seal
• Burnt out driving gear
• Broken driving belt
Noise
• Worn or burnt gear
• Worn gear
9-2
Disassembly of Final Driving
Mechanism
Remove the rear wheel. (refer to chapter 15)
Remove the clutch.
Drain gear oil out from gear box.
Remove gear box cover bolts (7 bolts) and then
remove the cover and the final driving shaft.
Remove gasket and setting pin.
7 bolts
Remove countershaft and gear. Final driving shaft

Remove final driving gear and shaft.
Final driving
Countershaft gear
gear
Countershaft
Driving shaft
Inspection Of Final Driving

Mechanism
Check if the countershaft and the gear are wear
out or damage.
Check if the final driving shaft and gear are burn,

wear or damage.
9-3
Check bearings on gear box and cover.
Rotate each bearing’s inner ring with fingers.
Check if bearings can be turned in smooth and
silent, and also check if bearing outer ring is
mounted on gear box & cover tightly.
If bearing rotation is uneven, noising, or loose
bearing mounted, then replace it.
Check oil seal for wear or damage, and replace it
if necessary.
Caution
• Do not remove the driving shaft from the
cover top side.
• If remove the driving shaft from the gear
box, then its bearing has to be replaced.
Check driving shaft and gear for wear or damage.
Bearing Replacement
Caution
• Never install used bearings. Once bearing
removed, it has to be replaced with new
one.
Remove driving shaft bearing from left crankcase

using following tools:
Install new driving shaft bearing into left

crankcase.
Special tool:
Press the bearing into cover with C type
hydraulic presser or bearing installer.
9-4
Press out the driving shaft from the gear box.
Remove oil seal from the gear box.
Remove the driving shaft bearing from the gear
box cover with the inner type bearing puller.
Caution
• Using the bearing protector as pressing
out the driving shaft from the gear box
cover.
Specified tool:
Inner type bearing puller.
If the driving shaft is pulled out with its bearing, Shaft protector
then remove the bearing with bearing puller and
bearing protector.
Special tool:
Multi-functional bearing puller
Bearing protector
Universal bearing
puller (inner type)
Install a new driving shaft bearing onto gear box

cover.
Then, install the driving shaft.
Specified tool:
Press the bearing in with C type hydraulic
presser or bearing installer.
Install a new final driving shaft bearing onto gear

box cover.
Specified tool:
Press the bearing in with C type hydraulic
presser or the bearing installer.
Apply with some grease onto the lip section of oil
seal and then install the seal.
9-5
Re-Assembly Of Final Driving
Mechanism Final Final driving Counter
driving shaft gear shaft
Install final driving shaft and final driving gear, shaft
countershaft, and countershaft gear.
Install the setting pins (2 pins) and new gasket.
Setting pins
Apply with grease onto the oil seal lip of final

driving shaft.
Install the gear box cover and 7 bolts. (tighten the
bolts)
Torque: 2.0~2.4 kgf-m
Install the clutch/sliding driving pulley.
Install the driving pulley, belt and left crankshaft
cover.
Install the rear wheel.
Add gear oil.
※Recommended usage: SYM HYPOID GEAR
OIL (SAE 85W-140)
(110 cc: standard capacity)
(100 cc: when replacement)
7 bolts
9-6
Home page Contents
10. Alternator/Starting Clutch
Mechanism Illustration ............10-1 Starting Clutch ........................ 10-5

Precautions in Operation ........10-2 Right Crankcase Cover Installation
.................................................. 10-8
Alternator Removal..................10-3
Mounted Coil Set Installation. 10-8
Alternator Coil Set Removal ...10-4
Flywheel Installation ............... 10-8
Right Crankcase Cover
Removal ....................................10-4
5.0~6.0 kgf-m
9.0~10.0 kgf-m
1.0~1.4 kgf-m
10
0.1~0.3 kgf-m
1.5~2.0 kgf-m
1.3~1.7 kgf-m
10-1
Precautions in Operation
General information
z Refer to chapter 5: Engine removal and installation
z Refer to chapter 1: The troubleshooting and inspection of alternator
z Refer to chapter 16: The service procedures and precaution items of starter motor
Item Service Limit
ID of starting driven gear 32.060
OD of starting clutch cover 27.940
ID of starting idle gear 10.05
OD of starting idle gear shaft 9.94
Torque value:
Flywheel nut 5.0~6.0 kgf-m
Bolt 8mm 1.5~2.0 kgf-m
Oil screen cover 1.3~1.7 kgf-m
Starting clutch mounting bolt 9.0~10.0 kgf-m with oil on the thread
Starting clutch hex socket bolt 1.0~1.4 kgf-m with adhesive

Flywheel puller
Universal fixture
10-2
Alternator Removal
Crankshaft Flywheel
position sensor Fan
Fan shroud
Coil Cable guide
Drain out the engine oil.

Remove the right side cover. ( 4 screws)
Remove the exhaust muffler. (2 bolts, 2 nuts)
Remove the fan shroud. (2 screws)
Remove the cooling fan shroud. (bolt x 2, screw
x 2)
Remove the cooling fan. (4 bolts)
Cooling fan
Hold the flywheel with the universal fixture.

Remove the 10mm nut on the flywheel. Universal fixture
Special Service Tools:
Universal Fixture
10-3
Remove the flywheel with the flywheel puller.
Special service tools:
Flywheel puller
shaft protector
Caution
Install a shaft protector on the right end of
crankshaft to avoid damaging the crankshaft
before installing the flywheel puller.
Flywheel puller
Pulse generator
coupler
Alternator Coil Set Removal
Remove the couplers of the alternator and pulse
generator.
Alternator coupler
Cable guide Pulse

generator
Remove the 6 bolts for the pulse generator, the
alternator coil and cable guide. Then, remove
the alternator assembly.
Caution
Do not damage the alternator coil.
Coil
8 bolts
Right Crankcase Cover Removal

Remove the right crankcase cover. (8 bolts)
Remove setting pin and gasket.
Remove the gasket or foreign materials on the
connection surfaces of both the cover and
crankcase.
Caution
Do not damage the connection surfaces.
10-4
Starting Clutch
Starting Clutch Removal
Hold the starting driven gear with the universal
fixture.
Remove the 22mm anti-loosen mounting nut and Mounting nut
gasket.
Anti-loosen mounting nut socket
Universal fixture
Caution
The mounting nut is left-turn thread. Mounting nut socket
Remove the starting driven gear.
Remove starting clutch, starting idle-gear, and

shaft.
Starting Clutch Inspection

Install the starting clutch onto the starting driven
gear.
Hold the starting clutch and turn the starting
driven gear.
The starting driven gear should can be turned in
the motion of C.W. and can not be turned in
C.C.W.
10-5
Check the starting driven gear for wear or
damage.
Measure the ID of the starting driven gear.
Service Limit:
ID: 32.06 mm or less
Check the starting idle gear and shaft for wear or

damage.
Measure the ID of the starting idle gear.
Service Limit:
ID: 10.05 mm or less
Measure the OD of the starting idle gear.

Service Limit:
OD: 9.94 mm or more
Disassembly
Remove the hex blots (3 bolts) inside the starting Plug Spring
clutch.
Separate the clutch body and the clutch cover.
Remove the rollers, plugs, and springs on the
one way clutch.
Roller
Check each rollers and plugs for wear or
damage.
Install rollers, plugs and springs.
Clutch body
Clutch cover
Measure the OD of the starting clutch cover.

Service Limit:
OD: 27.94 mm or more
10-6
Installation
Install the components in the reverse procedures
of removal. Plug Spring
Caution
Add adhere seal onto the thread of hex
socket bolt. Roller
Clutch body
Clutch cover
Starting clutch Installation

Install idle gear shaft and idle gear.
Install starting clutch.
Install the starting driven gear onto the starting

clutch.
Hold the starting driven gear with the universal

fixture.
Tighten the 22mm anti-loosen mounting nut and
gasket.
Caution
Add engine oil onto the thread of mounting Mounting nut
nut.

Anti-loosen mounting nut socket
Universal fixture.
Torque value: 9.0~10.0 kgf-m Mounting nut socket
10-7
Right Crankcase Cover Installation 8 bolts
Install setting pin and new gasket on the
crankcase.
Replace the right crankshaft oil seal of the
crankcase and apply some oil onto the oil seal
lip.
Install right crankcase cover onto the right
crankcase. (8 bolts)
Cable guide Pulse

Mounted Coil Set Installation
generator
Install the coil set onto right crankcase cover. (2
screws)
Install crankshaft position sensor. (2 screws)
Tighten the cable guide. (2 screws)
Torque: 1.5~2.0 kgf-m
Tie the wire harness hose onto the indent of
crankcase.
Caution
Make sure that the wire harness is placed
under the crankshaft position sensor. Coil
Pulse generator
Connect the connectors of alternator and
coupler
crankshaft position sensor.
Alternator coupler
Flywheel Installation Universal fixture
Make sure that there is no magnetic powder. If

so, clean up it.
Align insert on crankshaft with the flywheel
groove, and then install the flywheel.
Hold the flywheel with flywheel holder, and
tighten its nut.
Special service tool:
Universal fixture
10-8
Install the cooling fan. (4 bolts)
Cooling fan
Install the cooling fan shroud. ( 3 screws)

Install the rear bracket mounting bolts. (2 bolts)
Install the exhaust pipe. (2 bolts, 2 nuts)
Install the right side cover. (4 screws)
Add some engine oil according to specified
quantity.
10-9
NOTE:
10-10
Home page Contents
11. Crankcase/Crankshaft
Mechanism Illustration ............11-1 Disassembly Of Crankcase ..... 11-3
Operational precautions..........11-2 Crankshaft Inspection.............. 11-4
Trouble diagnosis ....................11-2 Assembly Of Crankcase .......... 11-5
1.5~2.0 kgf-m
1.0~1.4 kgf-m
11
0.7~1.0 kgf-m
0.8~1.2 kgf-m
0.8~1.2 kgf-m
3.5~4.5 kgf-m
11-1
Operational precautions
General Information
• This Section contains descriptions concerning disassembly of the crankcase so that the crankshaft
can be serviced.
• Complete following operations before disassembling crankcase.
Engine Chapter 5
Cylinder head Chapter 6
Cylinder/ piston Chapter 7
V-belt Drive pulley Chapter 8
Alternator/Foot Starting Clutch Chapter 10
Start motor Chapter 16
• If the crankshaft bearing or timing sprocket need be replaced, then the crankshaft set have to
replaced.
Item Standard Limit
Left, right clearance of the big end of the connecting rod 0.100~0.300 0.550
Right angle clearance of the big end of the connecting rod 0.000~0.008 0.050
Run-out ─ 0.100
Torque value
Bolts for crankcase : 1.5~2.0 kgf-m
Bolts for cylinder/cylinder head : 0.7~1.0 kgf-m
Engine oil draining plug : 3.5~4.5 kgf-m
Bolts for cam chain tensioner : 0.8~1.2 kgf-m
Special Service Tools

Crankcase remover/set
Crankshaft installation puller
Outer type bearing puller
Bearing pressing tools
Oil seal pressing tools
Trouble diagnosis
Engine noise
• Loose crankshaft bearing
• Loose crankshaft pin bearing
• Wear piston pin or piston pin hole
11-2
Disassembly Of Crankcase
Hex-socket bolt x 1
Remove the cam chain tensioner (hex socket
bolt x 1) from the left crankcase side.
Remove the 2 bolts from the right side of Screw x 2

crankcase, and then remove the right crankcase.
Remove the crankshaft from the left crankcase.

Remove the cam chain.
Remove the gasket and setting pin. (2 bolts)
Scrape gasket residues off the crankcase contact
surface.
Caution
• Check if the right & left bearings are

press-in the crankshaft.
• Do not damage contact surface of the
crankcase.
• Soap the gasket residues into solvent and
the residues will be removed easily.
Remove oil seal from the left crankcase side.
11-3
Crankshaft Inspection
Measure left and right clearance of connecting
rod big end.
Service limit: Replace when it is more than
0.55 mm
Measure the radical clearance of the big end at

the vertical directions.
Service limit : 0.05 mm
Place the crankshaft onto a V-block and measure

run-out of the crankshaft with dial gauge.
60 mm 90 mm
Bearing Inspection
Rotate the bearing with fingers and make sure
the bearing can be rotated smoothly and quietly. Clearance
Check if the inner ring is connected onto the
crankshaft tightly. Clearance
Replace crankshaft as a set when noise or
looseness is detected.
曲軸軸承
11-4
Assembly Of Crankcase
Install cam chain into the chain hole of the left
crankcase, and then split out the cam chain.
Caution
Do not damage the cam chain as installing
the crankshaft.
Install crankshaft into the left crankcase and then

install two dowel pins and new crankcase gasket. Dowel pins
Install the right crankcase and tighten the 2 bolts

crankcase bolts. (2 bolts)
Install the cam chain tensioner. Hex-socket bolt

Install a new O-ring onto the mounting bolt of the
chain tensioner.
Apply some oil on the O-ring and tighten the bolt.
Caution
The O-ring must be installed into the bolt’s
groove.
11-5
Apply with some grease onto the oil seal lip and
then install it onto the left crankcase.
Press-fit the oil seal to specified position with the

oil seal installer (25x37x6).
Special service tools: the oil seal installer
(25x37x6)
11-6
Home page Contents
12. Body Cover
Mechanism Illustration ............ 12-1 Luggage Box ............................12-8

Maintenance Information ........ 12-2 Rear Carrier ..............................12-9
Front Cover............................... 12-3 Body Cover .............................12-10
Handlebar Cover ...................... 12-4 Left & Right Side-Foot Plates 12-11
Front Fender............................. 12-5 Left & Right Side-Covers.......12-11
Front Under Spoiler ................. 12-6 Floor Panel..............................12-12
Inner Box .................................. 12-7 Rear Fender ............................12-13
Center Cover ............................ 12-8
Seat
Luggage box
Handlebar rear cover

Handlebar side Rear Carrier
cover (RH)
Right body
cover
Right side cover

Center body 12
cover
Left-body
Handlebar cover Center cover cover
Handlebar side
cover (LH) Tail light
set
Right foot
plate
Battery
cover Left foot plate
Front cover
Inner rear Rear
fender fender
Left side cover

Floor panel
Inner cover
Front fender
Foot mat
Front under
spoiler Under Cover
12-1
12. Body Cover
Maintenance Information
Body covers disassemble sequence:
Handlebar Rear
Front cover Center cover
Cover
Handlebar Left/right
side cover Front fender Luggage box & seat
Handlebar front Front under Spoiler Rear carrier

cover
Inner cover Body cover
Left/Right foot Rear fender /

plates Tail light set
Left/right
Inner rear fender
side-covers
Floor Panel
Under Cover
• Be careful not to damage various covers in disassembly or re-assembly operation.

• Never injure hooks molded on the body covers in disassembly or re-assembly operation.
• Align the buckles on the guards with slot on the covers.
• Make sure that each hook is properly installed during the assembly.
• Never compact forcefully or hammer the guard and the covers during assembly.
12-2
12. Body Cover
Front Cover
Removal
Remove the 8 mounting screws from the inside
of front inner cover.
Screw x 8
Remove the upper screw (screw x 1) from the

front fender. Screw x 1
Remove the front light wire coupler.
Front light wire coupler
Remove the front cover.
Installation
Install according to the reverse procedure of
removal.
12-3
12. Body Cover
Handlebar Cover Screw x 5
Removal
Remove the handlebar rear cover (screw x 5).
Disconnect the wire connectors of left & right
switches.
Remove the handlebar rear cover.
Caution
• Open the hooks on the two end-section
of the handlebar cover as removing the
cover. The, remove the handlebar cover.
Do not pull it forcedly to avoid to breaking
the hooks.
Remove the front cover, and odometer wire

coupler.
碼錶電線接頭
Remove the odometer cable. Screw x 4

Remove the handlebar front cover and odometer
set. (screw x 4)
Remove the odometer cover. (screw x 3)
Disassemble the odometer cover and the
odometer set. (screw x 2)
Odometer cable Switch wire connector
Installation
removal.
12-4
12. Body Cover
Front Fender
Removal
Remove the speedometer cable.(screw x 1)
Screw ×1
Remove the front fender screws. (left & right x 2) Left & right screws x 2
Installation
removal.
12-5
12. Body Cover
Front Under Spoiler
Removal
Remove the front fender, front cover.
Remove the screw (screw x 2) from the top-end
of front under spoiler.
Screw on each side ×1
Remove the inner cover screw. (left & right each

side x 1)
Screw on each side x 1
Remove 2 screws on the left & right each side of

side cover.
Screw on each side x 1
Remove the front under spoiler.
Installation
removal.
12-6
12. Body Cover
Inner Cover
Removal
Remove the front cover and front under spoiler
firstly.
Remove the mounting bolts (2 bolts) of floor
Panel.
Bolt x 2
Remove 1 bolt and ignition switch cap. Ignition switch cap
Bolt ×1
Take out the front inner cover.
Installation
removal.
12-7
12. Body Cover
Center Cover
Removal
Remove the 1 upper screw inside of the luggage
box.
Remove the lower 2-screws in front of the center

cover.
Take out the center cover.
Installation
removal.
Bolt x 2
Bolt x 2
Luggage Box
Removal
Open the seat.
Remove the 1 upper screw inside of the front
luggage box.
Remove the 2 mounting nuts and 2 bolts of the
luggage box.
Nut x 1
Lift the luggage box up by pushing the luggage

box & seat upward.
Installation
removal.
12-8
12. Body Cover
Rear Carrier Bolt x 4
Removal
Remove the hex-socket bolts (bolt x 4) of the rear
carrier.
Caution
Do not open the fuel tank cap as removing

the bolts so that prevent from bolts falling
into the fuel tank.
Open the fuel tank cap with key.
Remove the rear carrier.
Installation
removal.
12-9
12. Body Cover
Body Cover
Screws and bolt on each side
Removal
Remove the rear carrier, luggage box and seat
firstly.
Remove the body cover mounting screws and
bolts. (1 screw and 1 bolt on each side)
Remove 2 screw in rear of the body cover.
Screw ×2
Remove the seat lock cable, then remove the

body cover.
Installation
removal.
Seat lock cable
12-10
12. Body Cover
Left & Right Side-Foot Plate Screws x 2
Removal
Remove the foot plate connection screws.
(2 screws on left & right each side)
Remove the rear bolts. (1 bolt on left & right each

side)
Remove the side foot plate.
Installation
removal.
Bolt x 1
Left & Right Side-Covers

Remove the mounting screws. (2 screws on left
& right each side)
2 screws on left & right each side
Pull out the side-cover backward so that the front

clipper can be separated.
Remove the side-covers.
Installation
removal.
12-11
12. Body Cover
Floor Panel Bolt x2
Removal
• Remove the center cover, luggage box, body
side covers, and body cover firstly.
• Remove the front mounting bolts (bolt x 2) of
the floor panel.
Remove the battery cover. (screw x 3)
Screw x 3
Remove the battery bracket (screw x 2) and

power cables.
Take out the battery.
Remove the bottom mounting screws from the

Screw x 1
floor panel, and then the floor panel.
Installation
removal.
12-12
12. Body Cover
Rear Fender
Removal Bolt x 2
Remove the upper bolts (bolt x 2) from the rear
fender.
Remove the left & right side bolt (1 bolt on each

side) from the rear fender.
Remove the rear turning signal lamp wire, and
then the rear fender.
Installation
removal.
1 bolt on left & right each side
12-13
12. Body Cover
NOTES:
12-14
Home page Contents
13. Brake
Front Disc Brake System.........13-1 Brake Fluid

Replacement/Air-Bleed ........... 13-6
Rear Drum Brake System ........13-2
Brake Caliper ........................... 13-7
Precautions in Operation ........13-3
Brake Disc................................ 13-8
Trouble Diagnosis....................13-4
Brake Master Cylinder ............ 13-8
Hydraulic Brake System
Inspection ................................. 13-5 Drum Brake System
Inspection ...............................13-11
Front Disc Brake System
3.5 kgf-m
13
0.55 kgf-m
1.8 kgf-m
4.5 kgf-m
13-1
13. Brake
Rear Drum Brake System
0.8~1.2 kgf-m
0.8~1.2 kgf-m
13-2
13. Brake
Caution
Inhaling asbestos may cause disorders of respiration system or cancer, therefore, never use air
hose or dry brush to clean brake parts. Use vacuum cleaner or other authorized tool instead.
• The brake caliper can be removed without removing the hydraulic system.
• After the hydraulic system is removed, or the brake system is felt to be too soft, bleed the hydraulic
system.
• While refilling brake fluid, care should be taken not to let the foreign material entering into the brake
system.
• Do not spill brake fluid on the painted surfaces, plastic or rubber parts to avoid damage.
• Check the operation of the brake system before you go.
Specifications Unit: mm
Item Standard Limit
The thickness of front brake disc 4.000 2.500
Front brake disc eccentricity 0.100 or less 0.300
Master cylinder inner diameter 11.000~11.043 11.055
ID of master cylinder piston 10.957~10.984 10.945
Diameter of front disc 273.000 ─
ID of front & rear brake drums 130.00 131.00
Thickness of front disc brake lining 5.100 2.000
Thickness of rear disc brake lining 5.100 2.000
Torque values
Brake hose bolt 3.50 kgf-m
Bolt for brake caliper 3.30 kgf-m
Brake lining pin bolt 1.80 kgf-m
Cap of Brake lining pin bolt 1.00 kgf-m
Air-bleed valve 0.55 kgf-m
13-3
13. Brake
Trouble Diagnosis
DISC BRAKE
Soft brake lever Uneven brake
1. Air inside the hydraulic system 1. Dirty brake lining/disc
2. Hydraulic system leaking 2. Poor wheel alignment
3. Worn master piston 3. Clogged brake hose
4. Worn brake pad 4. Deformed or warped brake disc
5. Poor brake caliper 5. Restricted brake hose and fittings
6. Worn brake lining/disc
7. Low brake fluid Tight brake
8. Blocked brake pipe 1. Dirty brake lining/disc
9. Warp/bent brake disc 2. Poor wheel alignment
10. Bent brake lever 3. Deformed or warped brake disc
Hard operation of brake lever Brake noise

1. Blocked brake system 1. Dirty lining
2. Poor brake caliper 2. Deformed brake disc
3. Blocked brake pipe 3. Poor brake caliper installation
4. Seized/worn master cylinder piston 4. Imbalance brake disc or wheel
5. Bent brake lever
DRUM BRAKE
Poor brake performance Tight operation or low return speed of brake
1. improper brake adjustment lever
2. worn brake lining 1. worn/broken/crack return spring
3. worn brake drum 2. worn drum
4. worn brake cam 3. Dirty brake lining
5. improper brake lining installation 4. brake seized caused from dirty brake drum
6. seized brake cable 5. seized brake cable
7. Dirty brake lining 6. worn brake cam
8. Dirty brake drum 7. improper brake lining installation
9. brake pad worn in brake cam area.
10. poor contact between brake arm and Brake noise
camshaft indent 1. worn brake lining
2. worn drum
3. Dirty brake lining
4. Dirty brake drum
13-4
13. Brake
Hydraulic Brake System Inspection
Hose connection
Inspection
Visual inspect for brake fluid leaking or damage.
Check if brake hose connection loosen with
wrench and turn the handlebar from right to left
motion or press down the shock absorber to
check if there is something is interfered with the
brake system or brake components.
Operate the brake system and check the brake

lining. Check the front brake from front side,
and replace the brake lining with new one when
the brake lining wear limitation groove reaches to Brake lining
the brake disc. wear limitation
groove
Brake caliper Brake disc

Park the motorcycle on a flat ground and check
its brake fluid level.
Recommended brake fluid: WELL RUN (DOT
3) brake fluid
CAUTION
z The fluid level will not be correct if parking
the motorcycle in title or just parking. It
has to waiting for around 3~5 minutes.
z Never use faked brake fluid to prevent from
chemical reaction.
z It has to apply with same brand brake fluid
to sure the brake performance. Lower
level
BRAKE FLUID ADD
Turn the handlebar to let the master cylinder in
Master cylinder
horizontal position before removed the master
cylinder cap. Mounting seat
Place a rag onto painting, plastic or rubber Punch
components when conduct brake system point
maintenance.
CAUTION
z Do not over the upper level when adding
brake fluid and avoid to spilling brake fluid
on painted surfaces, plastic or rubber
components to result in their damages.
Split ring “UP” mark
13-5
13. Brake
Remove the master cylinder cap and diaphragm.

Screw
Add good quality brake fluid and it has to add
same brand brake fluid into the master cylinder. Master cylinder
Clean dirty brake disc. Diaphragm plate
CAUTION MAX. Diaphragm
The dirty brake lining or disc will reduce the

brake performance. The mixed
non-compatible brake fluid will reduce brake
performance. Foreign materials will block the
system causing brake performance to be
reduced or totally lost. MIN.
Brake Fluid Replacement/Air-Bleed

Connect drain hose to drain valve.
Open the drain valve on the caliper and hold and
release the brake lever alternatively until the old Drain valve
brake fluid is entirely drained out. Close the
drain valve and add specified brake fluid into the
brake master cylinder.
CAUTION
To reuse the spent brake fluid will effect brake
performance.
Connect one end of transparent hose to the drain

valve, and put the other end into a container.
Open the drain valve around 1/4 turns, and at the
same time hold the brake lever until the there is Drain valve
no air bubble in the drain hose and also feeling Bubble
resistance on the brake lever.
Close the drain valve when finishing the brake
system refilling fluid procedure, and operate the
brake lever to check whether air bubble is in
brake system or not. If brake is still soft, please
bleed the system as described below.
1. Tightly hold the brake lever and open the drain
valve around 1/4 turns, and then close the
valve.
CAUTION
Transparent draining hose
z Do not release the brake lever before the
drain valve is closed.
z Always check the brake fluid level when
carrying out the air bleeding procedure to
avoid air entering into the system.
2. Slowly release the brake lever, and wait for a

few seconds until it reaches its top position.
3. Repeat the steps 1 and 2 until there is no air
bubble at the end of the hose. Tightly close the
drain valve.
4. Make sure the brake fluid is in the UPPER
level of the master cylinder, and refill the fluid
if necessary.
5. Cover the cap.
13-6
13. Brake
Brake Caliper
Removal Bolts x 2
Place a container under the brake caliper, and
loosen the brake hose bolt and finally remove the
brake hoses.
CAUTION
• Do not spill brake fluid on painted surfaces.
• The exhaust pipe has to be removed
before remove the rear brake caliper.
Remove the bolt cap, and loosen the lining guide

bolt.
Remove two caliper bolts and the caliper.
Front brake caliper
INSTALLATION
Install the brake caliper and tighten the attaching
bolts securely.
Torque: 3.3 kgf-m
CAUTION
• Use M8 x 35 mm flange bolt only.
• Long bolt will impair the operation of brake
disc.
Tighten the lining guide bolt.
Torque: 1.8 kgf-m
Install the bolt cap.

Torque: 1.0 kgf-m Rear brake caliper
Use two seal washers and hose bolts to lock the

hose and brake caliper in place.
Torque: 3.5 kgf-m
Refill up the brake fluid to the reservoir and make

necessary air bleeding.
13-7
13. Brake
Brake Disc
Inspection
Visually check the brake disc for wear or break.
Measure the thickness of the disc at several Brake
places. Replace the disc if it has exceeded the disc
service limit.
Allowable limit: 2.0 mm
Micrometer
Remove the brake disc from wheel.

Check the disc for deformation and bend.
CAUTION
• Do not let grease touch to the brake disc
that will cause brake performance.
• Do not clean the brake lining with air gun
because the lining is contained asbestos.
Operator should wear mask & glove and
use vacuum cleaner to clean the brake
lining.
Brake Master Cylinder

Removal
CAUTION
Do not let foreign materials enter into the
cylinder. Master
cylinder
CAUTION
The whole set of master cylinder, piston,
spring, diaphragm and clip should be
replaced after removal.
Remove the front and rear handlebar guards.
Remove the leads of brake lamp switch.
Drain out the brake fluid. Brake
Remove the brake lever from the brake master hose
cylinder.
Remove the brake hose.
Remove the master cylinder seat and the master Clip
cylinder. Rubber
Remove the rubber pad. washer
Piston
Remove the clip.
Remove the piston and the spring. Spring
Clean the master cylinder with recommended
brake fluid.
Master
cylinder
13-8
13. Brake
Inspection
Master
Check the master cylinder for damage or scratch. cylinder
Measure the cylinder inner diameter at several
points along both X and Y directions.
Replace the cylinder if the measured values
exceed allowable limit.
Dial
gauge
Measure the outer diameter of the piston.
Replace the piston if its measured value exceeds
allowable limit.
Allowable limit: 10.945 mm Piston
Micrometer
Assembly
CAUTION
Rubber Sub-rubber
• It is necessary to replace the whole set boot washer
comprising piston, spring, piston cup, and
clip. clip
• Make sure there is no dust on all Piston
components before assembling.
Main rubber
Apply clean brake fluid to the piston cup, and washer
then install the cup onto the piston. Spring
Install the larger end of the spring onto the
master cylinder.
The master cup’s cavity should be face inside of Master
master cylinder when installing the master cup. cylinder
Install the clip.
CAUTION
• Never install cup lip in the opposite
direction.
• Make sure the clip is seated securely in the
groove.
Install the rubber pad into groove properly.
13-9
13. Brake
INSTALLATION
Master cylinder
Place the master cylinder onto handlebar, and Mounting
install the split ring and bolts. The “UP” mark on seat
the split ring should face upward.
Align the split ring on the master cylinder seat Punch
with the alignment point on the handlebar. point
Tighten the upper bolt of the seat to specified
torque value, and then tighten lower bolt to the
same specified torque value.
Split ring
“UP” mark
Install the brake lever, and connect leads to

brake lamp switch.
Connect brake hoses with 2 new washes. Sealing washer
Tighten the brake hose bolt to the specified
torque value.
Torque value: 3.5 kgf-m
Make sure the hose is installed correctly.
CAUTION
Improper routing may damage leads, hoses
Hose bolt
or pipes.
Brake hose
CAUTION
Kink of brake leads, hose or pipe may
reduce brake performance.
Add specified brake fluid and bleed the system

and conduct the air-bleeding job for the system.
13-10
13. Brake
DRUM BRAKE SYSTEM
INSPECTION
BRAKE DRUM
Removal
Use a vacuum cleaner and other suitable tools
to clean the brake parts to minimize the hazard
caused by the asbestos dust.
Caution
y Inhaling asbestos dust may cause
respiration system disorder even cancer.
Never use an air hose or a dry brush as to Nut ×1
clean the brake parts.
y Grease on brake lining will reduce braking
efficiency.
Remove wheel. Remove brake drum from

wheel hub.
Inspection
Check the brake drum for wear and damage,
replace wheel hub if necessary
Measure the ID of hub at several points and
record the largest value.
Service limit : Rear 131.0 mm
Caution
Rear brake drum
y Remove the rust by using #120 sand
paper. Brake lining
y An inside micrometer must be used when
measuring ID of brake drum because the
brake drum has a friction back plate.
BRAKE LINING
Inspection
Measure the thickness of the brake lining at three
points (both ends and center).
If the thickness is less than specified, or if it is
contaminated by oil or grease, replace as a set.
Service limit : Rear 1.1 mm
Removal
Caution Brake cam
Brake linings must be replaced as a set.
Remove brake shoes from the brake panel by Brake spring
pulling out the brake linings with two hands.
Installation
Apply a thin coat of grease to the brake cam and 後
the anchor pin.
Hook the brake spring onto the brake cam.
Pull out the brake linings and install them onto the
brake panel. Wipe off the excessive grease from Anchor pin
the brake cam and the anchor pin after Brake shoes
installation.
13-11
13. Brake
Slightly grind the brake lining surfaces with
sand-paper to clean the surfaces. Brake cam
Caution
Braking efficiency will be reduced if brake
lining is contaminated by oil or grease. Anchor
pin
Brake spring
Brake
BRAKE PANEL
Removal
Remove the brake arm bolt and then remove
the brake arm, wear indicator, brake return
spring and brake cam as well as the oil seal Return Brake cam
from the brake panel. spring
Bolt
Wear indicator
Brake arm
Installation
Front brake panel
Apply a thin cost of grease onto the brake cam Oil seals
shaft.
Install the brake cam.
Apply a thin cost of grease onto the oil seal lip
and then install the oil seal onto the brake cam
shaft. Finally, install it on the brake panel.
Align the end-part of the brake return spring
with the hole of brake panel.
Align both the inner gear of wear indicator and Brake arm
the mark on the brake arm with the indent gear Brake cam
of brake cam, and then install it.
Tighten the bolts and nuts to specified torque.
Torque: 0.8~1.2kgf-m
Rear Brake Panel

Apply a thin cost of grease between the oil
seals on the brake cam shaft.
Install the brake cam.
Align the mark on the brake arm with the inner
gear of the brake cam.
Tighten the bolts and nuts to specified torque.
Hook on the return spring.
Torque: 0.8~1.2kgf-m
13-12
Home page Contents
14. Steering/Front Wheel/Front Shock Absorber
Mechanism Illustration.............14-1 Front Wheel............................... 14-4

Precautions in Operation .........14-2 Front shock absorber .............. 14-7
Trouble diagnosis.....................14-2 Front fork/steering column...... 14-7
Steering Handlebar...................14-3
4.0~5.0 kgf-m
1.0~2.0 kgf-m
0.2~0.3 kgf-m
2.4~3.0 kgf-m 14
3.1~3.5 kgf-m
5.0~7.0 kgf-m
14-1
General Information
• Before remove front wheel, use a jack to lift the body until front wheel free of ground, and take
care not to rotate body in reverse.
• Be careful not to allow oil or grease get on brake drum or linings.
Torque values
Front wheel axle 5.0~7.0 kgf-m
Steering handlebar nut 4.0~5.0 kgf-m
Steering column top cone sliding ring 0.2~0.3 kgf-m
Steering column lock nut 1.0~2.0 kgf-m
Speedometer cable nut 0.15~0.3 kgf-m
Front shock absorber: Upper nut 2.4~3.0 kgf-m
Tools
Steering column wrench
Bearing remover
Inner type bearing remover
Attachment, 32×35 mm
Attachment, 42×47 mm
Steering column nut wrench
Steering column top cone ring nut wrench
Trouble diagnosis
Front wheel wobbling
Hard steering stem • Bent wheel rim
• Over tightening of steering stem lock nut
• Loose wheel axle nut
• Damaged steering stem steel ball and
• Poor wheel or wearing
steering stem bearing seat • Too much clearance on wheel bearing
• Insufficient tire pressure
Soft front suspension

Steering stem off center • Front shock absorber spring worn out
• Uneven left/right cushion
• Oil leaking on cushion oil ring
• Bend fork
• Bent front wheel/tire offset
Front suspension noise
• Bent shock absorber linkage
• Loosen shock absorber nut
14-2
Steering Handlebar Master cylinder
REMOVAL
Remove handlebar front & rear cover and the
front cover (refer to chapter 12).
Disc Brake
Remove the 2 bolts of the brake master cylinder,
and then take out the master cylinder and the
split ring.
Caution
Mounting
Do not operate the front brake lever to avoid Bolts
seat
to pressing out the brake lining when
removing the master cylinder.
Remove throttle handlebar housing screw and

then remove the handlebar, throttle cable, and
handlebar upper housing & under housing.
Screw
Remove the mounting bolt of the rear brake

cylinder. (bolt x 2)
Take out rear brake cylinder.
Bolts x 2
With a wrench to hold the handlebar bolt and

then remove the nut.
Take out the handlebar after removed the bolt. Bolt
Installation
Install the handlebar according to the reverse
procedure of removal.
Apply with some grease onto the handlebar
moving parts when installing the throttle
handlebar housing, throttle handlebar, and Nut
throttle cable.
14-3
Front Wheel
Removal Speedometer
Support body bottom and lift front wheel free of cable
ground.
Remove the screw, and disconnect speedometer
cable from the gear box.
Remove the wheel axle nut and pull out the axle.
Then, remove the front wheel.
Caution
Do not operate the front brake lever to avoid
to pressing out the brake lining when
removing the master cylinder.
Wheel axle
nut
Inspection
Wheel axle
Set the axle in V-blocks and measure the run-out.
Wheel axle
Wheel Rim
Place the wheel onto a rotated bracket.
Turn the wheel with hand and measure its
wobble value with a dial gauge.
Service limit:
Radial : 2.0 mm
Axial : 2.0 mm
14-4
Disassembly
Remove the left axle ring and dust seal. Bearing
Remove the dust seal on the right side of
speedometer gear.
Remove the bearing with the inner type bearing
remover.
Take out the bearing spacer and then remove the Wheel side
other bearing. collar
Speedometer
Tool: Bearing
gear dust
Inner type bearing remover. seal
Dust seal
Bearing bushing
Bearing Inspection
Turn the inner race of bearing with fingers. The Clearance
bearing should be turn smoothly. Also check if Clearance
the outer collar is tightly connected to the wheel
hub.
If the bearing do not turn smoothly, or if they are
too loose in the races, or damaged, then, remove
and replace the bearings with new ones.
Caution
The bearing must be replaced in pair.
Installation
Install the bearing according to the reverse
Apply some grease into the bearing seat of the
wheel hub.
Install the left bearing onto the seat.
Install the bearing spacer and then install the
right bearing onto the seat.
14-5
Caution
Do not install used bearing and replace the
bearing once it has been removed.
Do not the bearing in tile motion when
installing.
Tool:
C-type compressor or bearing compressor.
Both samples will damage bearing
Align the flange part on the speedometer gear

with the slot of wheel hub, and then install the
speedometer gear box.
Caution
Contaminated brake lining will reduce brake
performance so the brake lining, brake drum
and disc must be free of grease.
Place the front wheel between the front shock

absorbers. Stopper
Align the flange part on the speedometer gear
with the slot of shock absorber stopper.
Brake panel
slot
Install the front wheel axle from right shock

absorber side.
Install the wheel axle nut, and tighten it to
specified torque value.
Connect the speedometer cable to the
speedometer gear box.
Wheel axle nut Speedometer cable
14-6
Front shock absorber
Removal
Remove the front fender, front under spoiler, front
cover, and front wheel as well as front brake
components.
Remove the brake fluid hose clipper or cable
guide on the left shock absorber. (bolt x 1)
As for disc brake, remove the cable guide on the
right shock absorber. (bolt x 1)
Brake
fluid hose
clipper
Remove the top connection bolt of the right Bolts

shock absorber. (bolt x 4)
Remove the shock absorber from the front fork.
Shock absorbers
Installation
Install the shock absorbers according to the
reverse procedure of removal.
Align the shock absorber top-edge with the
top-end level of the front fork when installing the
front shock absorber onto the front fork. Then,
tighten the nut.
Front fork/steering column

Removal Steering lock
Firstly, remove the handlebar, front wheel, front nut
brake set, and front shock absorbers.
Remove the steering lock nut.
Remove the top cone race, and then remove the
steering column.
Caution
Place the steering column bearing balls into a
parts container to avoid to missing or
Steering top
shortage.
cone race
14-7
With a plastic hammer to tap the steering ball
race slightly, and then remove the top ball
bearing race.
Remove the lower-end cone bearing race on the
frame with a punch.
Caution
Do not damage the frame and the steering
race.
Installation Lower ball bearing Steering lock

Install a new top-cone bearing race onto the top race nut
Balls
of steering column.
And then, push the lower-cone bearing seat from
bottom until to locking position. Lower
cone-race
Caution Top
Do not let the ball bearing in title motion as cone-race
installation. Balls
Apply with some grease onto the top & bottom

Top ball bearing
bearing balls, and then install the balls into race
bearing race.
Press in a new lower cone-race onto the steering
column, and lubricate it with grease.
Install the steering column.
Lubricate the top-cone race with grease. Steering lock
nut
Drive the cone-race into the steering column until
Return 1/2 turns
contact with the top bearing seat no clearance.
Note, return 1/2 turn and then tighten the top
cone race to specified torque. (tighten the race
around 1/4~3/8 turn more.)
Locking to
Caution 1/4~3/8 turns
Do not tighten the top cone race too tight to

prevent from damage the ball bearing seat Top cone-race
when tightening the top cone race.
Install the steering lock nut and lock the top cone
race. Then, tighten the nut.
Torque value: 1.0~2.0 kgf-m Steering
Install the bearing seat according to the reverse column nut
Caution
Check the steering column if it can be turned
freely and no clearance in vertical motion.
Top
cone-race
14-8
Home page Contents
15. Rear Wheel / Rear Shock Absorber
Mechanism Illustration.............15-1 Exhaust Muffler ........................ 15-3

Precautions in Operation .........15-2 Rear Wheel................................ 15-3
Trouble Diagnosis ....................15-2 Rear Shock Absorber .............. 15-4
3.5~4.5kgf-m
2.4~3.0kgf-m
0.8~1.2kgf-m
15
10.0~12.0kgf-m 3.2~3.8kgf-m
3.2~3.8kgf-m
15-1
General Information
As for the wheel removal, service, and installation procedures, please refer to the service manual of
high speed tire.
Items Standard Limit
Radial - 2.0
Wheel wobbling
Axial - 2.0
Thickness of rear brake lining 4.0 2.0
Torque values
Rear axle nut 10.0~12.0 kgf-m
Rear brake arm bolt 0.8~1.2 kgf-m
Rear shock absorber upper mount bolt 3.5~4.5 kgf-m
Rear shock absorber lower mount bolt 2.4~3.0 kgf-m
Exhaust pipe connection nut 1.0~1.2 kgf-m
Exhaust pipe connection bolt 3.2~3.8 kgf-m
Trouble Diagnosis
Rear wheel wobbling Braking Noise Poor brake performance
• bend wheel rim • worn brake lining • Poor brake adjustment
• poor tire • brake drum deformation • contaminated brake lining
• loosen wheel shaft • improperly brake panel • worn brake lining
installation • Air inside of the brake
Shock absorber too soft • unparalleled brake drum or hose/pipe
• insufficient shock absorber wheel unparallel. • greased brake disc
spring force • Clogged brake pipe
• Bent brake pipe
• Insufficient brake fluid
15-2
Exhaust Muffler Nuts x 2
Removal
Remove the front-end nut of the exhaust muffler.
(nut x 2)
Remove the bolts. (bolts x 3)
Remove the exhaust muffler.
Installation
Install the exhaust muffler according to the
Caution
Replace the exhaust muffler gasket if it is
broken or deformed.
Torque value:
Exhaust muffler connection bolt: 3.2~3.8 kgf-m
Exhaust muffler connection nut: 1.0~1.2 kgf-m
Bolts x 4
Rear Wheel
INSPECTION
Measure wheel rim wobbling.
Service limit:
Radial: 2.0 mm
Axial: 2.0 mm
• If the wheel rim wobbling out of the
specification, except resulted from the wheel
rim deformation, it might be loosen or worn
final driving shaft bearing or bend, deformed
driving shaft.
Removal
Remove the exhaust muffler. (bolt x 4 &
nut x 2)
Remove the rear wheel nut. (nut x 1)
Remove the rear wheel nut and exhaust muffler
rear mount.
15-3
Rear Shock Absorber
Removal
Remove the luggage box. (bolt x4, screw x1)
Remove the body cover. (screw x 4)
Remove the air cleaner. (bolt x2)
Bolt x 2
Remove the under bolt of the rear shock Bolt x 1

absorber. (bolt x 1)
Remove the upper bolt of the rear shock Bolt x 1

absorber. (bolt x 1)
Remove the rear shock absorber.
Installation
Install the rear shock absorber according to the
Caution
The rear shock absorber has to be replaced

with one set and can not be replaced by
unauthorized persons. Otherwise, it might
damage the rubber bushing and
construction.
Torque values
Rear shock absorber lower mount bolt:
2.4~3.0 kgf-m
Rear shock absorber upper mount bolt:
3.5~4.5 kgf-m
15-4
Home page Contents
16. Electrical Equipment
Mechanism Illustration ............16-1 Ignition System ........................16-9

Precautions In Operation ........16-2 Starting System......................16-12
Specification.............................16-3 Meter........................................16-14
Trouble diagnosis ....................16-4 Light / Light Bulb....................16-16
Battery.......................................16-4 Switch / Horn ..........................16-18
Charging system......................16-5 Fuel Gauge Unit......................16-21
Horn
Winker relay
Horn switch /
Winker switch / Start switch /
Dimmer & Passing Headlight switch
switch
Main switch
C.D.I. unit (ignition switch)
Battery Fuse box
Ignition coil Spark plug
16
Alternator
Starter relay
Regulator
Fuel gauge unit
16-1
Charging System
y When remove the battery, the disconnection sequence of cable terminals shall be strictly observed.
(First disconnect the negative cable terminal, next, the positive cable terminal.)
y MF (Maintenance Free) battery does not need to check, add electrolyte or distilled water.
y Battery must be taken out from scooter when charging the battery. But do not open the battery
caps.
y Do not quick charge the battery unless in emergency.
y A voltmeter must be used when checking battery charging condition.
y Battery can be charged or discharged alternately. To set a discharged battery idle for a prolonged
period will shorten its service life and reduce its capacity. Usually, battery’s capacity will reduce
after 1~2 years. After low capacity battery was charged, its voltage will increase. If it connects to an
additional load, the voltage will reduce suddenly, and then go up again.
y Over-charged battery. Usually, the over-charged battery can be seen externally. If a short circuit
occurred inside the battery, there will be no voltage on the terminals of battery if voltage regulator
does not operate. Then, the battery’s voltage will be too high that may reduce battery’s life.
y The battery will be self-discharged if it was set idle for a long time. An idle battery must be charged
about every 2months.
y A new battery filled with electrolyte will generate a voltage after filled out electrolyte. The voltage
should be in 12.5V or more after 10 minutes. When electrolyte is not enough, the battery must be
filled with electrolyte and then charged to prolong the battery’s life-span.
y Please check electrical device according to the procedure of diagnosis chart.
y Do not disconnect and connect the connector of electrical devices when current is passing these
devices because this will generate high voltage and the electrical components in the
voltage-current regulator will be damaged. The ignition switch must be turned OFF before
performing any work.
y Please do not replace with traditional type battery as replacement.
y Please refer to the removal instruction when removing the alternator and the pulse generator.
Ignition System
y Please follow the procedure of trouble diagnosis chart to check ignition system.
y The ignition system equipped with a auto-advanced timing device in CDI unit. Thus, ignition timing
need not to be adjusted. In case of incorrect ignition timing occurred, check the CDI unit or
alternator system. It has to check the ignition timing with the ignition timing lamp if replaced these
components.
y Do not hang or impact the CDI unit of ignition system because the major faulty of CDI unit is
caused by impact. Therefore, take care when disassembling.
y Most of ignition system problems were resulted from poor connecting connector. Please check
the connectors first when servicing.
y Make sure that the heat range of spark plug is suitable. Improper spark plug is the main cause of
poor engine operation or combustion.
y Inspection procedures in this manual are based on Max. voltage. This manual also contains
methods of how to check ignition coil resistance and component operation.
y Please follow the continuity chart to check ignition switch.
Starting System
y Starting motor can be removed directly from engine.
y Please refer to chapter 10 for starting clutch removal procedures.
16-2
Specification
Charging System
Items Specification
Capacity/type 12V6Ah / YTX7A-BS
Charging rate STD:0.6A/5~10hrs, emergency charging: 6A/0.5hrs
Battery
Voltage Full charged 13.1V
(20℃) Under charged 12.3V
Capacity 12V / 6.2A
Alternator Lighting coil resistance (20℃) Between yellow-green: 0.1-0.8Ω
Charging coil resistance (20℃) Between white-green: 0.2-1.0Ω
Leaking current Less 1mA
RPM for starting charging 2000rpm(headlamp ON)
Voltage controlled by regulator 14.0±0.5 V
Resistance (20℃) 20W5.9Ω 7.0~8.0Ω
Resistor
Resistance (20℃) 5W5Ω 4.5~5.5Ω
Ignition System
Item Specification
Standard NGK C7HSA (Recommended usage)
Hot type NGK C8HSA
Spark plug
Cold type NGK C6HSA
Spark plug gap 0.6~0.7 mm
Primary 0.21±10%Ω
Ignition coil resistance
(20℃) With plug cap : 3~5 KΩ
Secondary
Without plug cap : 7~12 KΩ
“F” Mark Before TDC 13° / 1700 rpm
Ignition timing Timing advanced Before TDC 28° / 4000 rpm
charactor Before TDC 27° / 8000 rpm
Pulse generator resistance (20℃) 50~200Ω
Exciting coil resistance (20℃) 400~800Ω
Ignition coil-primary max. voltage 95~400 V
Pulse generator voltage 1.7 V above
Exciting coil voltage 95~400 V
Starting System
Item Specification
Type DC TYPE
Start motor
Capacity 0.5 KW
16-3
Trouble diagnosis
No power supply Intermittent power supply
• Dead battery • Loose charging system connection
• Disconnect battery cable • Loose battery cables
• Fuse burned out • Loose connection or short-circuit in discharging
• Faulty ignition switch system
• Loose connection or short-circuit in lighting
system
Low voltage Charging system failure
• Weak battery • burn Fuse
• Loose battery connection • Loose, broken or shorted wire or wire
• Charging system failure connection
• Voltage-current regulator failure • Faulty voltage regulator
• Faulty alternator
Start motor does not work Weak start motor
• The fuse is blown • Poor charging system
• The battery is not fully charge • The battery is not fully charged
• Poor main switch • Poor connection in the windings
• Poor start switch • The motor gear is jammed by foreign material
• The front and rear brake switches do not Starter motor is working, but engine does not
operate correctly crank
• Starter relay is out of work • Poor start motor pinion
• The ignition coil is poorly connected, open or • The start motor run in reverse direction
short-circuited • Poor battery
• The start motor is out of work
Battery
Removal
Remove the rubber carpet.
Remove the battery cap. (screw x 3)
Remove the battery mounting bracket. (bolt x 2)
Firstly, remove the negative(-) post, and remove
the positive (+) post.
Remove the battery.
Voltage Inspection
Measure the voltage with a digital voltage meter.
Voltage Value:
Fully charged: 13.0~13.2V at 20℃
undercharged: less 12.3V at 20℃
16-4
Charging system
Charging wire circuit
Main switch
Fuse
Green
Black
Red
10A
Yellow
Pink
Battery
Alternator
Regulator
Charging
Connect the battery charger’s positive (+)
terminal to battery’s positive (+) post.
Connect the battery charger’s positive (-)
terminal to battery’s positive (-) post.
Standard Max
Charging current 0.9A 16.0A
Charging time 5~10H 1H
Warning
y Strictly keep flames away from a charging
battery.
y The charging ON/OFF is controlled by the
charger’s switch. Do not control the
charging by battery jump wires.
Caution
y Quick charge a battery should be used only
in an emergency.
y Make sure the current and charging time of
above description.
y The battery will be damaged by too much
current or too rush charging.
After installing the battery, coat the terminals with

clean grease.
16-5

Current Leakage Test
Current Leakage Inspection
Turn the main switch to OFF position, and
remove the negative cable terminal (-) from the
Battery (-) terminal
battery.
Connect an ammeter between the negative cable
terminal and the battery negative terminal (as
shown on left diagram).
Caution
Ground
• In the current leakage test, set the current wire
range at larger scale, then gradually
decrease to the lower scale as the test
process goes to avoid possible damage to
the ammeter and the fuse.
• Do not turn the main switch to ON position
during test.
If the leaked current exceeds the specified value,

it may indicate a short circuit.
Allowable current leakage: Less than 1 mA
Disconnect each cable one by one and take
measurement of the current of each cable to
locate the short circuit.
Charging Voltage/Current Inspection
Caution
• Before conducting the inspection, be sure
that the battery is fully charged. Use a fully Digital meter
charged battery having a voltage larger than Ammeter
13.0 V. If undercharged, the current changes
dramatically.
• While starting the engine, the starter motor
draws large amount of current from the
battery. Thus, do not start the engine with
battery.
After the engine is warmed up, replace original

battery with a fully charged battery.
Fuse connector
Connect a digital voltmeter to the battery
terminals.
Connect an ammeter between both ends of the
main fuse.
Caution
When the probe is reversibly connected, use
a voltmeter having an indication that the
current flows from the positive or the negative
direction and the measurement should be at
zero, ammeter at one direction only.
16-6
Caution
Main switch
• Do not use short-circuit cable.
• It is possible to measure the current by
connecting an ammeter between the
battery positive terminal and the cable
position terminal, however, while the starter
motor is activated, the surge current of the
motor draws from the battery may damage
the ammeter. Use the foot lever to start the
engine.
• The main switch shall be turned to OFF
position during the process of inspection.
Never tamper with the ammeter and the
cable while there is current flowing through.
It may damage the ammeter.
Connect a tachometer.
Turn on the headlamp to high beam and start
the engine.
Accelerate the engine gradually to the specified
revolution per minute and measure the charging
voltage/current.
Charging Current: 4.8A/1600 rpm
Control Charging Voltage:
14.0±0.5 V / 2000 rpm
Caution
To replace the old battery, use a new battery
with the same current and voltage.
The following problems are related to the

charging system, follow the instructions provided
in the checking list to correct it if any one of the
problems takes place.
(1) The charging voltage can not exceed the
voltage between two battery terminals and
the charging current is in the discharging
direction.
(2) The charging voltage and current are too
much higher than the standard values.
The following problems are not related to the
charging system; correct it if any by following
steps indicate in the checking list.
(1) The standard charging voltage and current
can only reach when the revolution of the
engine exceeds the specified rpm.
- Bulbs used exceed their rate and
consume too much power.
- The replacement battery is aged and
does not have enough capacity.
(2) The charging voltage is normal, but the
current is not.
- The replacement battery is aged and
does not have enough capacity.
- Battery used do not have enough
electricity or is over charged.
- The fuse of the ammeter is blown.
- The ammeter is improperly connected.
(3) The charging current is normal, but the
voltage is not.
- The fuse of the voltmeter is blown.
16-7
REGULATOR INSPECTION
Remove the rear carrier. (refer to chapter 12,
section 8)
Remove the body cover. (refer to chapter 12,
section 8)
Disconnect the 5P connector of the regulator.
Measurement
Item Standard Value
point
Main switch Battery voltage
R~B
connection wire (ON)
Battery
R~G Battery voltage
connection wire
Check the parts onto the abnormal wire circuit if

the measured values are not within standards.
If the parts is OK, then it is the wire circuit
abnormal.
Replace the regulator if both checks are OK.
CHARGING COIL INSPECTION

Caution
The coil need not be removed from engine
as conduct this test.
Regulator
At the alternator side from the regulator
connector, measure the resistor between pink
and yellow wires.
Standard value: 0.16~0.8Ω
16-8
Ignition System
Ignition System Circuit
Blue / Yellow Green
Black / Red Black /

Yellow
Exciter
coil Black / White
C.D.I. set
Green
Pulsator Main switch Ignition Coil
Spark plug
Alternator
CDI UNIT
Removal
Remove the battery cover, then the CDI unit can
be removed from the battery cover.
CDI UNIT
Check
Disconnect the connector from the CDI unit.
Make the following inspection at each terminal of the harness side connector.
ITEM Measure at: Standard (at 20C)
Main Switch Black/white-green Continuity as main switch OFF
Exciter Coil Black/Red-Green 400 ~800Ω
Pulse Generator Blue/Yellow-green 50 ~200Ω
Primary Black/yellow-green 0.21Ω±10%

Ignition Coil Green-high voltage cable -w/o Cap 3~5KΩ
Secondary
Green-high voltage cable - w/ Cap 7~12KΩ
16-9
IGNITION COIL Ignition coil
Removal
Remove the luggage box, central cover.
Remove spark plug cap.
Remove the primary coil wire of ignition coil.
Remove the fix bolts for the ignition coil, and
remove the coil.
Install the coil in reverse order of removal.
Caution
Install primary coil with black/yellow lead
connected to black connector and green lead
connected to green connector.
Spark plug confirmation

Remove the spark plug and install a good plug
into plug cap, and then ground it to engine ground.
Make sure its spark condition. If it is in not good or
burnt spark plug, replace the spark plug with new
one.
Caution
y Make sure each wire connection is correct,
and test as required. Even the wire
connection is in correct, sometimes, it
might not be tested occurred.
Connect the high voltage shunt with a

multi-meter or input a resistor in the 10M 10CV of
voltage meter. Black / yellow
Connect ignition coil wires, and connect a shunt
between primary terminal (black/yellow and
green) and frame ground.
Press the starting motor button, or starting lever
to test the max. primary voltage of ignition coil.
Connection: connect (+) terminal to green side, Green
and (-) to black/yellow side.
Min. voltage: Above 95 V.
Caution High voltage shunt
Do not touch metal parts on the test probe with

fingers to avoid electric shock.
Primary coil check

Disconnect the primary coil connector and check
the resistance between primary coil terminals.
Standard: 0.21Ω±10%Ω(at 20℃)
Primary coil is good if resistance within standard.
Primary coil is broken if resistance is infinite.
Replace the coil.
16-10
Secondary coil
Attached the spark plug cap, measure the
resistance between plug cap side and green
terminal.
Standard value: 7-12 kΩ(20℃)
Remove the spark plug cap, measure the
resistance between plug cap side and green
terminal.
Standard value: 3-5 kΩ(20℃)
Secondary coil is good if resistance within
standard.
Secondary coil is broken if resistance is infinite. If
the spark plug cap attached and the measured
value is exceed standard value, it means the
spark plug cap is in not good.
Ignition coil
Replacement
Remove the ignition coil bolt to replace the
ignition coil if necessary.
PULSATOR
Caution
Checking pulsator can be done on engine.
But, the spark plug must be installed onto
the cylinder head, and cylinder compression
pressure must be in normal condition.
Check
Remove body cover.
Remove the pulsator connector.
Measure the resistance between blue/yellow
terminal on engine side and frame ground.
Standard: 50-200Ω(20℃)
Replace the alternator if the measured value
exceeds standard value.
Exciting coil
Remove the exciting coil connector.
Measure the resistance between black/red wire
on engine side and frame ground.
Standard: 400-800Ω(20℃)
Replace the alternator if the measured value
exceeds the standard value.
16-11
Starting System
Starting Circuit
Main switch
Fuse 10A Battery
Red
Start motor
Yellow / red
Brake switch Start relay
Green / yellow
Start switch
Start Relay Inspection

Turn main switch to "on", and operate the brake
lever. Then press start button to check if there a
click sound. It is normal if there is a click sound.
Start relay
Remove the luggage box assembly.
Disconnect the battery negative (-) terminal.
Remove the battery positive (+) connection and
starting motor wires from the start relay large pin.
Remove the power control connector of the start
relay.
Connect a Ohmmeter between the start relay
large pins.
Connect the green/yellow wire to battery positive
(+) terminal, and the green/yellow wire to battery
negative (-) terminal.
Check the continuity between the start relay large
pins.
If it is not continuity, then replace the start relay.
16-12
START MOTOR REMOVAL
Remove the luggage box. (chapter 12, section 6)
Remove the air cleaner. (chapter 4, section 10)
Remove the battery negative terminal.

Remove the battery positive terminal and the
start motor wire from the big terminal of start
relay.
Remove the start motor mounting bolts and the
motor.
Remove the start motor mounting bolts and the

motor.
Starting Motor Installation

Install the motor and other components in
16-13
Meter
Removal
Remove the front cover. (chapter 12, section 4)
Remove the power coupler of the meter.
Remove the rear cover of the handlebar. (chapter

12, section 3)
Remove the odometer cable.
速度錶導線
Remove the winker relay coupler.
Winker relay coupler
16-14
Remove the front cover of handlebar. (chapter 12,
Screw x 4
section 3)
Screw x 4
Remove the instrument panel assembly.
(screw x 4)
Disassemble the instrument seat and the

instrument. (screw x 2)
Instrument Panel Installation

Install the panel in reverse procedure of removal.
16-15
Light / Light Bulb
Headlight Bulb Replacement
Remove the front cover. (chapter 12, section 4)
Disconnect the headlight wire connector, and
then remove the rubber boot.
Press down the bulb spring locker and then
remove the locker with turning it in CCW motion.
Replace the bulb with new one if necessary.
Caution
• Do not touch the bulb surface with fingers
because the bulb will create hot-spot so
that let it be burnt. It has to be package
with cloth or wear glove as installing.
• Wipe the bulb with cloth to prevent from
damaged if the bulb be touched by hands.
Install the bulb in reverse order of removal.

Connect power to check if the bulb has been
installed properly after installation.
Please conduct the headlight beam adjustment
job if replace the headlight bulb.
The headlight beam adjustment

Loosen the adjustment screw located under the
headlight. Turn the screw to right or left to adjust
the high or low beam of headlight.
Caution
y This outer cover of headlight is a fixed type

so that the lamp seat will be moved only
when adjusting.
Headlight adjustment screw
16-16
Front Turn Signal Light Bulb Replacement
Remove the light outer cover of the turn signal
light. (screw x 2)
Remove the light inner cover of the turn signal

lamp. (screw x 1)
Replace the bulb with new one.
Rear Turning Signal Light Replacement

Pry out the light cover from the preset slot onto
the lower parts of cover.
Check if the bulb is burnt or damage, and replace
it if necessary.
Preset slot
Taillight / Brake Light Replacement

Remove the outer cover of the tail & brake light.
(screw x 2)
Check if the bulb is burnt or damage, and replace
it if necessary.
Screw x 2
16-17
Switch / Horn
Main Switch
Inspection
Remove front fender. (bolts x2, screws x4)
Disconnect main switch leads connector.
Check connector terminals for continuity.
Pin
BAT1 BAT2 IG E
Location
LOCK ● ●
OFF ● ●
ON ● ●
Black/
Wire color Red Black Green
White
Replacement
Remove the handlebar bolt. (bolt x 1)
Bolt ×1
Remove the handlebar assembly.
Remove the main switch connector and bolts.

(bolts x 3)
Remove the main switch.
Install a new main switch and tighten the bolts.
(bolts x 3)
Bolt ×3
16-18
Handlebar switch
Remove the rear handlebar cover. (chapter 12,
section 3)
Disconnect the connector of the handlebar
switch.
Check the continuity of follow pins listed below
columns.
Start switch
ST E
Start motor
FREE switch
● ●
Wire color Yellow/ Red Green
Headlight switch
CI TL HL
● ●
● ● ●
Brown/
Wire color Black brown
white
Headlight switch
High/Low beam switch & Passing switch Hi/Lo beam & Passing switch
LO HL HI PASS
● ●
● ●
PASSING ● ● ● ●
Brown/
Wire color White Blue Black
white
16-19
Turn signal light switch

Turn signal light switch
R WR L
● ●
FROM R ● ●
N PUSH OFF
FROM L ● ●
Horn switch
● ●
Light
Wire color Gray Orange
blue
Horn
Connect 12V power to the 2 pins on the horn.
Then, the horn should sound.
Brake light switch

The circuit of black wire and the green/yellow
wire on the brake light switch should be in
continuity when operating the brake lever.
If the switch damaged, replace it with new one.
Brake lamp switch
16-20
Fuel Gauge Unit
Fuel gauge unit remove
Open the seat cushion
Remove the luggage box assembly (bolts x4,
screw x1)
Remove the rear carrier (bolts x4)
Remove the central cover (screws x 2)
Remove the left & right body covers (bolts x 2,
screw x 4).
Disconnect the fuel gauge unit coupler.
Fuel unit coupler
Turn the plastic cap in CCW direction and then

remove the fuel unit plastic cap.
Remove the fuel gauge unit.
Caution
Do not damage or bend the float arm as
removing.
Fuel unit plastic cap
Inspection Fuel unit

The resistance values are listed below when the
float arm in F and E positions.
Float arm position Resistance value
E(empty) 97.5~107.5Ω
F(full) 4~10Ω
DOWN(empty)Connect the fuel gauge unit to the
main harness.
Turn the main switch ON.
Move the float arm in UP & DOWN, and then
check if the fuel gauge indication needle is in
correct position.
UP
Caution
(full)
Turn on the turn signal light to make sure
battery is in good condition before this test.
Float arm position Indicator needle
UP(full) E(empty)
DOWN
(empty)
DOWN(empty) F(full)
16-21
NOTE:
16-22
Home page Contents
17. Wiring Diagram
HE15W Wiring Diagram
17
17-1
Home page Contents
17. Wiring Diagram
NOTE:
17-2

Sym Euro MX 125 Service Manual

Uploaded by

Copyright:

Available Formats

Sym Euro MX 125 Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sym Euro MX 125 Service Manual

Uploaded by

Copyright:

Available Formats

FORWARD CONTENTS

HOW TO USE THIS MANUAL MECHANISM ILLUSTRATIONS

This service manual contains the technical data of each component

This service manual describes basic information of different system parts

The first chapter covers general information and trouble diagnosis.

Page Content Index

1-1 ~ 1-16 General Information / Trouble Diagnosis 1

2-1 ~ 2-18 Service Maintenance Information 2

3-1 ~ 3-8 Lubrication System 3

4-1 ~ 4-14 Fuel System 4

5-1 ~ 5-10 Engine Removal 5

6-1 ~ 6-16 Cylinder Head / Valve 6

7-1 ~ 7-8 Cylinder / Piston 7

8-1 ~ 8-14 “V” Type Belt Driving System / Foot-Starter 8

9-1 ~ 9-6 Final Driving Mechanism 9

10-1 ~ 10-10 Alternator / Starting Clutch 10

11-1 ~ 11-6 Crankcase/Crankshaft 11

12-1 ~ 12-14 Body Cover 12

13-1 ~ 13-12 Brake System 13

14-1 ~ 14-8 Steering/Front Wheel/Suspension 14

15-1 ~ 15-4 Rear Wheel/Suspension 15

16-1 ~ 16-22 Electrical Equipment 16

17-1 ~ 17-2 Wiring Diagram 17

Rear winker light

Gear oil drain

Symbols And Marks.................. 1-1 Torque Values (Frame) ........... 1-11 1

Symbols And Marks

Grease King Mate G-3 is recommended. (KING MATE G-3)

King Mate gear oil (SYM HYPOID GEAR OIL ) is recommended.

Oil seal Apply with lubricant.

Renew Replace with a new part before installation.

Special tools Special service tools.

correct Meaning correct installation.

wrong Meaning wrong installation.

Indication Indication of components.

directions Indicates position and operation directions.

Components assembly directions each other.

Hot components Spilling brake fluid on painted, plastic, or

• Rubber parts may become deteriorated when

• When servicing this motorcycle, use only

• The ends of rubber hoses (for fuel, vacuum, or

• Tighten assemblies with different dimension Clamp

Both of these examples can result in bearing

• Check if positions and operation for installed

• Make sure service safety each other when

• Make sure that the battery post caps are

• Note that do not let parts fall down.

• Insert the terminal completely.

• Do not pull the wires as removing a connector

• Secure wires and wire harnesses to the frame

• Keep wire harnesses far away from the hot

• Route wire harnesses to avoid sharp edges or

• Route harnesses so that they neither pull too

• Wire harnesses routed along the handlebar

• Before operating a test instrument, operator

Do you know how to set the

Two /110 kg PERFOR Max. Speed 96 km/hr Above

Exhaust Pipe Position Right side, and

Cylinder head nuts 4 8 2.0~2.4

Valve adjustment fixing nuts 4 5 0.7~1.1 Apply oil to thread