MSDS NO: 415889

MATERIAL SAFETY DATA SHEET

REVISED: April 30, 2009
TW 3575 C
For U.S. Manufactured or Distributed Welding Consumables and Related Products. May be used to comply with OSHA's Hazard Communication Standard, 29 CFR 1910.1200 and Superfund
Amendments and Reauthorization Act (SARA) of 1986 Public Law 99-499. Standard must be consulted for specific requirements.

SECTION 1 – IDENTIFICATION

Manufacturer/Supplier Name: HOBART BROTHERS COMPANY Telephone No: (937) 332-4000

Address: 101 TRADE SQUARE EAST, TROY, OH 45373 Emergency No: (800) 424-9300
Website: www.hobartbrothers.com

Product Type: TUBULAR ARC WELDING ELECTRODES FOR FLUX CORED, METAL CORED AND COMPOSITE SUBMERGED ARC WELDING

GROUP A: Product For: Gas Shielded Carbon and Low Alloy Steel
Trade Name: EXCEL-ARC 71; FABCO 80D2, 82HD, 85, 90, 825, E70T-1C, E70T-9C H8, HORNET, RXR, RXR-XLS, TR70, XL-71; FABCOR 80XLS, 86R, 96, 702; FABDUAL T9M, T91M; FLUX-
COR 2, 3, 7,9XT, 37, 80A1, 90D3; GALVACOR; GALVALLOY; METAL-COR 3, 3S, 6, 6L, 8, 80D2, EH14S, EL12KS, EM12KS, EN-VISION; METALLOY 70, 70R, 70X, 71,76, 80D2,
A1S, A3S, CO2, EH14S, EL12KS, EM12KS, EM13KS, X-CEL; PIPEMASTER MC70; SPEED-ALLOY 70, 71, 71A, 71A1, 71-V, 719, 75, 95D2, 105D2; SPEED-COR 6; SUPER-COR;
SUPER TUF-COR; TM-11, 22, 37, 55, 71 XTR, 72, 73, 75A1, 81A1, 91D3, 95D2, 105D2, 711M, 791, 811A1, RX7; TRIPLE-7, 8; TUF-COR 1, 5, 75A1, 95D2, 105D2;
VERSATILE; VERTI-COR I, II, III, 71, 81A1

GROUP B: Product For: Self-Shielded Carbon Steel

Trade Name: FABSHIELD 4, 21B, 23, 31, 55, 120C, 7027, HSR; SELF-SHIELD 3, 4, 7, 11, 11GS; SPEED-SHIELD 11, GS; TM- 33R, 44, 77, 121, 123, 133

GROUP C: Product For: Carbon and Low Alloy Steel

Trade Name: DURASHIELD 8-11; EDGE; FABCO 81K2-C, 83, 91, 91K2-C, 107G, 110, 110K3-M, 115, 803, HICOR, XTREME 120, B2, B3; FABCOR 209, 1100; FABSHIELD 3Ni1, 71K6,
81N1, 81N2, 811K6, 7018, OFFSHORE 71Ni, XLNT-6, XLR-8, X80; FLUX-COR 80B2, 80Ni1, 80Ni2, 80W, 90B3, 90K2, 90Ni2, 100K3, 110K3; FORMULA XL8Ni1, XL8Ni1-C,
XL525, XL550, GD5; HOBART CBC-1; MATRIX; MEGAZORD; METAL-COR 80B2, 80Ni1, 80Ni2, 80Ni3, 90, 90B3, 100, 110, B2S, B3S, F2S, MAXIM, N1S, N2S, N3S, N4S, WS;
METALLOY 80B2, 80N1, 80N2, 80N3, 80W, 90, 90B3, 100, 100G, 110, 120S, B2S, B3S, F2S, N1S, N2S, N3S, N4S, VANTAGE, VANTAGE CVN, VANTAGE D2, VANTAGE Ni1,
WS; PREMIER 70; PW-201; PIPEMASTER F100-K2, F101-K2, F110-N1, F71, FS71-K6, FS71Ni1, FS 81-Ni2, MC90, MC100; SELF-SHIELD 8; SPEED-ALLOY 71-VC, 81B2L-V,
81Ni1-V, 81Ni2-V, 81W, 81W-V, 85, 85C1, 85C2, 85C3, 91B3, 91B3L, 91B3L-V, 91B3-V, 91-V, 92S, 95, 100F3-S, 111-V, 112-S, 115, 125, 712, 712M, 790, 4130-V; TM-
78K6, 81B2, 81N1, 81N2, 81W, 85B2L, 85N1, 85N2, 85N3, 91B3, 91B3L, 91K2, 91N2, 95K2, 95M-B3, 101K3, 105K3, 111K3, 115, 125K4, 770, 771, 71HYN, 772, 811B2,
811N1, 811N2, 811N3, 811W, 880, 881K2, 910, 911B3, 911N2, 991K2, 101, 101K3-C, 1101K3-M, 4130; TUF-COR 85B2L, 85Ni1, 85Ni2, 85Ni3, 95B3, 95K2, 105K3, 115,
125K4; VERTI-COR 70, 72, 81B2, 81Ni1, 81Ni2, 81W, 91B3, 91K2, 91Ni2, 110K3-M, 1101K3-C, IINi1

GROUP D: Product For: Corrosion Resisting Steel

Trade Name: ARC STAR 409; FABCOR 409; FABLOY 409, 409T, 439; FABTUF 250, 960; METAL-COR 409, 409Cb, 439; METALLOY 18CrCb, 409, 409Cb, MCW430NbL, 439; POWERCORE
91; RSC-409; SPEED-ALLOY 5055; TM B6, B9

SECTION 2 - HAZARDOUS INGREDIENTS

IMPORTANT - This section covers the hazardous materials from which this product is manufactured. The fumes and gases produced during welding with normal use of this product are also addressed
in Section 5. The term "hazardous" in this section should be interpreted as a term required and defined in OSHA Hazard Communication Standard (29 CFR Part 1910.1200).

GROUP - % WEIGHT EXPOSURE LIMIT (mg/m3)

HAZARDOUS INGREDIENTS A B C D CAS NO. OSHA PEL ACGIH TLV

IRON+ 75-98 75-95 75-95 75-95 7439-89-6 5 R* 5 R* (Fe2O3) {A4}

IRON OXIDE --- --- <12 --- 1309-37-1 10 (Oxide Fume) 5 R* (Fe2O3) {A4}
MANGANESE# <5 <2 <4 <2 7439-96-5 5 CL ** (Fume) 0.2 I* {A4} ∆
1, 3 STEL*** ∆∆∆ 0.02 R* ∆, ∆∆
TITANIUM DIOXIDE <10 <4(4) <10 <2 13463-67-7 15 (Dust) 10 {A4}
SILICON+ <4 <2(4) <4 <2 7440-21-3 5 R* 3 R*
FLUORSPAR <5(5) <10 <5 --- 7789-75-5 2.5 (as F) 2.5 (as F) {A4}
MOLYBDENUM <1 --- <2 <2 7439-98-7 5 R* 3 R*; 10 I* (Elemental and Insoluble)
0.5 R* (Soluble Compounds) {A3}
CALCIUM CARBONATE <2 <2(7) --- --- 1317-65-3 5 R*, 5 (as CaO) 3 R*, 2 (as CaO)
ALUMINUM### <2 <5 <3(6) --- 7429-90-5 5 R* (Dust) 1 R* {A4}
MAGNESIUM+ --- <3 <2 --- 7439-95-4 5 R* 3 R*
MAGNESIUM OXIDE --- <3 <2 --- 1309-48-4 15 (Fume, total particulate) 10 I* {A4}
BARIUM FLOURIDE# --- <12(1) <12(3) --- 7787-32-8 0.5 (as Ba) 0.5 (as Ba) {A4}
NICKEL# --- --- <4 <1 7440-02-0 1 (Metal) 1.5 I* (Elemental) {A5}
1 (Soluble Compounds) 0.1 I* (Soluble Compounds) {A4}
1 (Insoluble Compounds) 0.2 I* (Insoluble Compounds) {A1}
CHROMIUM# --- --- <3 5-20 7440-47-3 1 (Metal) 0.5 (Metal) {A4}
0.5 (Cr II & Cr III Compounds) 0.5 (Cr III Compounds) {A4}
0.005 (Cr VI Compounds) 0.05 (Cr VI Soluble Compounds) {A1}
0.01 (Cr VI Insoluble Compounds) {A1}
COPPER# <1(2) --- <2(2) --- 7440-50-8 0.1 (Fume), 1 (Dust) 0.2 (Fume), 1 (Dust and Mists)
TITANIUM+ --- <2 <2 <2 7440-32-6 5 R* 3 R*
SILICA++ <2 <2 <2 --- 14808-60-7 0.1 R* 0.025 R* {A2}
(Amorphous Silica Fume) 69012-64-2 0.8 3 R*
LITHIUM FLUORIDE --- <2(9) <2(9) --- 7789-24-4 2.5 (as F) 2.5 (as F) {A4}
STRONTIUM FLUORIDE --- <2(8) --- --- 7783-48-4 2.5 (as F) 2.5 (as F) {A4}
COBALT --- --- <1(10) --- 7440-48-4 0.1 (Dust&Fume) 0.02 {A3}
CERIUM OXIDE --- --- <2(11) --- 1306-38-3 5 R* (Dust), 15 (Dust) 3 R* (Dust), 10 (Dust)
ANTIMONY TRIOXIDE --- --- <1(12) --- 1309-64-4 0.5 (as Sb) 0.5 (as Sb) {A2}

(1) Present only in FABSHIELD 21B, 23, 31, 120 C; TM 121 and 123; SELF-SHIELD 11,11GS (2) Present only in FABCO 83, 110K3-M, FLUX-COR 80W, GALVACORE; GALVALLOY; METALLOY 80 W, WS;
METAL-COR 81W; SPEED-ALLOY 81W, 81W-V; TM-81W, 811W; VERTI-COR 81W (3) Present only in DURASHIELD 8-11; FABCO XTREME 120, B2, B3; FABSHIELD 3Ni1, 7018, 71K6, 81N1, 81N2, 811K6,
OFFSHORE 71Ni, XLNT-6; PIPEMASTER FS71-Ni1, FS81-Ni2; SELF-SHIELD 8; TM 78K6 (4) Present only in FABSHIELD 55; SELF SHIELD 3; TM 33, 133 (5) Present only in FABCO 85; METALLLOY EM13K5;
SPEED-ALLOY 75, 75A1, 95D2, 105D2; TM 55, 75A1, 95D2, 105D2; TUF-COR 5, 75A1, 95D2, 105D2 (6) Present only in DURASHIELD 8-11; FABCO XTREME 120, B2, B3; FABSHIELD 3Ni1, 7018, 71K6,
81N1, 81N2, 811K6, OFFSHORE 71Ni, XLNT-6; PIPEMASTER FS71-Ni1, FS81-Ni2; SELF – SHIELD 8; TM 78K6 (7) Present only in FABSHIELD 7018, 7027; SELF – SHIELD 8; TM 77, 133 (8) Present only in
FABSHIELD 21B; TM 121. (9) Present only in DURASHIELD 8-11; FABSHIELD 3Ni1, 7018, 7027, 71K6, 81N1, 81N2, 811K6, OFFSHORE 71Ni; PIPEMASTER FS71-Ni1, FS81-Ni2; SELF-SHIELD 8; TM 78K6
(10) Present only in DURASHIELD 8-11; FABSHIELD 71K6, 81N1, 81N2; MEGAZORD; PIPEMASTER F110-N1, FS71-Ni1, FS81-Ni2 (11) Present only in DURASHIELD 8-11; FABSHIELD 7018, OFFSHORE

415889 April 30, 2009 Page 1 of 3

71Ni, XLNT-6; SELF-SHIELD 8 (12) Present only in MATRIX; METAL-COR MAXIM; METALLOY VANTAGE, VANTAGE CVN, VANTAGE D2, VANTAGE Ni1 R* - Respirable Fraction I* - Inhalable Fraction
** - Ceiling Limit *** - Short Term Exposure Limit + - As a nuisance particulate covered under "Particulates Not Otherwise Regulated" by OSHA or "Particulates Not Otherwise Classified" by ACGIH
++ - Crystalline silica is bound within the product as it exists in the package. However, research indicates silica is present in welding fume in the amorphous (noncrystalline) form # - Reportable
material under Section 313 of SARA ### - Reportable material under Section 313 of SARA as dust or fume {A1} - Confirmed Human Carcinogen per ACGIH {A2} - Suspected Human Carcinogen per
ACGIH {A3} - Confirmed Animal Carcinogen with Unknown Relevance to Humans per ACGIH {A4} - Not Classifiable as a Human Carcinogen per ACGIH {A5} - Not Suspected as a Human Carcinogen
per ACGIH (noncrystalline) form ∆ - Listed under ACGIH Notice of Intended Changes for Mn in 2009 ∆∆ - Limit of 0.02 mg/m3 is proposed for Respirable Mn in 2010 by ACGIH ∆∆∆ - NIOSH
Recommended Exposure Limit (REL) TWA and STEL

The exposure limit for welding fume has been established at 5 mg/m3 with OSHA's PEL. The individual complex compounds within the fume may have lower exposure limits than the general
welding fume PEL. An Industrial Hygienist, the OSHA Permissible Exposure Limits for Air Contaminants (29 CFR 1910.1000), and the ACGIH Threshold Limit Values should be consulted to
determine the specific fume constituents present and their respective exposure limits.

SECTION 3 - PHYSICAL/CHEMICAL CHARACTERISTICS

Welding consumables applicable to this sheet are solid and nonvolatile as shipped.

SECTION 4 - FIRE AND EXPLOSION HAZARD DATA

Welding consumables applicable to this sheet as shipped are nonreactive, nonflammable, nonexplosive and essentially nonhazardous until welded. Welding arcs and sparks can ignite combustibles
and flammable products. See American National Standard Z49.1 referenced in Section 7.

SECTION 5 - REACTIVITY DATA - HAZARDOUS DECOMPOSITION/INDUSTRIAL HYGIENE INFORMATION

Welding fumes and gases cannot be classified simply. The composition and quantity of both are dependent upon the metal being welded, the process, procedures and electrodes used. Most fume
ingredients are present as complex oxides and compounds and not as pure metals.

Other conditions which also influence the composition and quantity of the fumes and gases to which workers may be exposed include: c oatings on the metal being welded (such as paint, plating or
galvanizing), the number of welders and the volume of the work area, the quality and amount of ventilation, the position of the welder's head with respect to the fume plume, as well as the presence
of contaminants in the atmosphere (such as chlorinated hydrocarbon vapors from cleaning and degreasing activities). When the electrode is consumed, the fume and gas decomposition products
generated are different in percent and form from the ingredients listed in Section 2. Decomposition products of normal opera tion include those originating from the volatilization, reaction or
oxidation of the materials shown in Section 2, plus those from the base metal and coating, etc., as noted above. Reasonably expected constituents of the fume would include: Complex oxides of iron,
manganese, silicon and titanium. Groups A and B may also contain calcium oxides. Groups A, B and C may have fluorides present. Groups A, C, and D may also contain molybdenum. Groups A, B,
and C may also contain aluminum. Groups B and C may also contain barium. Groups A and C may also contain copper. Groups C and D may also contain chromium and nickel. Group B may also
contain magnesium, lithium and strontium. Group C may also contain cobalt. Group C may also contain antimony trioxide.

Monitor for the materials identified in Section 2. Fumes from the use of this product may contain: manganese, fluorspar or fluorides, barium, chromium and nickel compounds, calcium oxide,
copper, silica, amorphous silica fume, lithium, strontium, cobalt and antimony trioxide whose exposure limits are lower than the 5 mg/m3 PEL for general welding fume. Gaseous reaction
products may include carbon monoxide and carbon dioxide. Ozone and nitrogen oxides may be formed by the radiation from the arc. One recommended way to determine the composition and
quantity of fumes and gases to which workers are exposed is to take an air sample inside the welder's helmet if worn or in the worker's breathing zone. [See ANSI/AWS F1.1, available from the
"American Welding Society", P.O. Box 351040, Miami, FL 33135. Also, from AWS is F1.3 "Evaluating Contaminants in the Welding Environment - A Sampling Strategy Guide", which gives additional
advice on sampling.]

SECTION 6 - HEALTH HAZARD DATA

EFFECTS OF OVEREXPOSURE:
Electric arc welding may create one or more of the following health hazards:
ARC RAYS can injure eyes and burn skin.
ELECTRIC SHOCK can kill. See Section 7.
FUMES AND GASES can be dangerous to your health.
PRIMARY ROUTES OF ENTRY are the respiratory system, eyes and/or skin.

SHORT-TERM (ACUTE) OVEREXPOSURE EFFECTS:

Welding Fumes - May result in discomfort such as dizziness, nausea or dryness or irritation of nose, throat or eyes. Iron, Iron Oxide - None are known. Treat as nuisance dust or fume. Manganese -
Metal fume fever characterized by chills, fever, upset stomach, vomiting, irritation of the throat and aching of body. Recovery is generally complete within 48 hours of the overexposure. Titanium
Dioxide - Irritation of respiratory system. Silica (Amorphous) - Dust and fumes may cause irritation of the respiratory system, skin and eyes. Fluorides - Fluoride compounds evolved may cause skin
and eye burns, pulmonary edema and bronchitis. Molybdenum, Cerium Oxide - Irritation of the eyes, nose and throat. Calcium Oxide - Dust or fumes may cause irritation of the respiratory system,
skin and eyes. Aluminum Oxide - Irritation of the respiratory system. Magnesium, Magnesium Oxide - Overexposure to the oxide may cause metal fume fever characterized by metallic taste,
tightness of chest and fever. Symptoms may last 24 to 48 hours following overexposure. Barium - Aching eyes, rhinitis, frontal headache, wheezing, laryngeal spasms, salivation or anorexia. Nickel,
Nickel Compounds - Metallic taste, nausea, tightness in chest, metal fume fever, allergic reaction. Chromium - Inhalation of fume with chromium (VI) compounds can cause irritation of the
respiratory tract, lung damage and asthma-like symptoms. Swallowing chromium (VI) salts can cause severe injury or death. Dust on skin can form ulcers. Eyes may be burned by chromium (VI)
compounds. Allergic reactions may occur in some people. Copper - Metal fume fever characterized by metallic taste, tightness of chest and fever. Symptoms may last 24 to 48 hours following
overexposure. Strontium Compounds - Strontium salts are generally non-toxic and are normally present in the human body. In large oral doses, they may cause gastrointestinal disorders, vomiting
and diarrhea. Lithium Compounds - Overexposure may cause tremor and nausea. Cobalt - Pulmonary irritation, cough, dermatitis, weight loss. Antimony Compounds - Irritation of nose, throat,
eyes and skin.

LONG-TERM (CHRONIC) OVEREXPOSURE EFFECTS:

Welding Fumes - Excess levels may cause bronchial asthma, lung fibrosis, pneumoconiosis or "siderosis." Iron, Iron Oxide Fumes - Can cause siderosis (deposits of iron in lungs) which some
researchers believe may affect pulmonary function. Lungs will clear in time when exposure to iron and its compounds ceases. Iron and magnetite (Fe3O4) are not regarded as fibrogenic materials.
Manganese - Long-term overexposure to manganese compounds may affect the central nervous system. Symptoms may be similar to Parkinson's disease and can include slowness, changes in
handwriting, gait impairment, muscle spasms and cramps and less commonly, tremor and behavioral changes. Employees who are overexposed to manganese compounds should be seen by a
physician for early detection of neurologic problems. Overexposure to manganese and manganese compounds above safe exposure limits can cause irreversible damage to the central nervous
system, including the brain, symptoms of which may include slurred speech, lethargy, tremor, muscular weakness, psychological disturbances and spastic gait. Titanium Dioxide - Pulmonary irritation
and slight fibrosis. Silica (Amorphous) - Research indicates that silica is present in welding fume in the amorphous form. Long term overexposure may cause pneumoconiosis. Noncrystalline forms of
silica (amorphous silica) are considered to have little fibrotic potential. Fluorides - Serious bone erosion (Osteoporosis) and mottling of teeth. Molybdenum, Cerium Oxide - Prolonged overexposure
may result in loss of appetite, weight loss, loss of muscle coordination, difficulty in breathing and anemia. Calcium Oxide - Prolonged overexposure may cause ulceration of the skin and perforation of
the nasal septum, dermatitis and pneumonia. Aluminum Oxide - Pulmonary fibrosis and emphysema. Magnesium, Magnesium Oxide - No adverse long term health effects have been reported in the
literature. Barium - Long term overexposure to soluble barium compounds may cause nervous disorders and may have deleterious effects on the heart, circulatory system and musculature. Nickel,
Nickel Compounds - Lung fibrosis or pneumoconiosis. Studies of nickel refinery workers indicated a higher incidence of lung and nasal cancers. Chromium - Ulceration and perforation of nasal
septum. Respiratory irritation may occur with symptoms resembling asthma. Studies have shown that chromate production workers exposed to hexavalent chromium compounds have an excess of
lung cancers. Chromium (VI) compounds are more readily absorbed through the skin than chromium (III) compounds. Good practice requires the reduction of employee exposure to chromium (III)
and (VI) compounds. Copper - Copper poisoning has been reported in the literature from exposure to high levels of copper. Liver damage can occur due to copper accumulating in the liver
characterized by cell destruction and cirrhosis. High levels of copper may cause anemia and jaundice. High levels of copper may cause central nervous system damage characterized by nerve fiber
separation and cerebral degeneration. Strontium Compounds - Strontium at high doses is known to concentrate in bone. Major signs of chronic toxicity, which involve the skeleton, have been
labeled as "strontium rickets". Lithium Compounds - May be considered as potentially teratogenic. Cobalt - Repeated overexposure to cobalt compounds can produce reduced pulmonary function,
diffuse nodular fibrosis of lungs and respiratory hypersensitivity. Antimony Compounds - Metal fume fever, dermatitis, keratitis, conjunctivitis and ulceration and perforation of the nasal septum.
Avoid conditions in which fresh hydrogen will react with antimony to form stibine which is extremely toxic.

415889 April 30, 2009 Page 2 of 3

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Persons with pre-existing impaired lung functions (asthma-like conditions). Persons with a pacemaker should not go near welding and cutting
operations until they have consulted their doctor and obtained information from the manufacturer of the device. Respirators are to be worn only after being medically cleared by your company-
designated physician.
EMERGENCY AND FIRST AID PROCEDURES: Call for medical aid. Employ first aid techniques recommended by the American Red Cross. Eyes & Skin: If irritation or flash burns develop after
exposure, consult a physician.
CARCINOGENICITY: Chromium VI compounds, nickel compounds and silica (crystalline quartz) are classified as IARC Group 1 and NTP Group K carcinogens. Titanium dioxide compounds, antimony
trioxide compounds and cobalt compounds are classified as IARC Group 2B carcinogens. Chromium VI compounds, cobalt compounds, nickel compounds, silica (crystalline quartz) and welding fumes
must be considered as carcinogens under OSHA (29 CFR 1910.1200).
CALIFORNIA PROPOSITION 65: For Group C and D products: WARNING: This product contains or produces a chemical known to the State of California to cause cancer and birth defects (or other
reproductive harm). (California Health & Safety Code Section 25249.5 et seq.) For Group A and B products: WARNING: This product, when used for welding or cutting, produces fumes or gases
which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

SECTION 7 - PRECAUTIONS FOR SAFE HANDLING & USE/APPLICABLE CONTROL MEASURES

Read and understand the manufacturer's instructions and the precautionary label on the product. See American National Standard Z49.1; Safety in Welding and Cutting published by the American
Welding Society, P.O. Box 351040, Miami, FL 33135 and OSHA Publication 2206 (29 CFR 1910), U.S. Government Printing Office, Washington, DC 20402 for more detail on any of the following.

VENTILATION: Use enough ventilation, local exhaust at the arc or both to keep the fumes and gases below PEL/TLVs in the worker's breathing zone and the general area. Train the welder to keep his
head out of the fumes.
RESPIRATORY PROTECTION: Use NIOSH approved or equivalent fume respirator or air supplied respirator when welding in confined space or where local exhaust or ventilation does not keep
exposure below PEL/TLVs.
EYE PROTECTION: Wear helmet or use face shield with filter lens. As a rule of thumb begin with Shade Number 14. Adjust if needed by selecting the next lighter and/or darker shade number.
Provide protective screens and flash goggles, if necessary, to shield others.
PROTECTIVE CLOTHING: Wear hand, head and body protection which help to prevent injury from radiation, sparks and electrical shock. See ANSI Z49.1. At a minimum this includes welder's gloves
and a protective face shield, and may include arm protectors, aprons, hats, shoulder protection as well as dark nonsynthetic clothing. Train the welder not to touch live electrical parts and to insulate
himself from work and ground.
PROCEDURE FOR CLEANUP OF SPILLS OR LEAKS: Not applicable
WASTE DISPOSAL: Prevent waste from contaminating surrounding environment. Discard any product, residue, disposable container or liner in an environmentally acceptable manner, in full
compliance with Federal, State and Local regulations.
SPECIAL PRECAUTIONS (IMPORTANT): Maintain exposure below the PEL/TLVs. Use industrial hygiene monitoring to ensure that your use of this material does not create exposures which exceed
PEL/TLVs. Always use exhaust ventilation. Refer to the following sources for important additional information: ANSI Z49.1 from the American Welding Society, P.O. Box 351040, Miami, FL 33135 and
OSHA (29 CFR 1910) from the U.S. Department of Labor, Washington, DC 20210.

Hobart Brothers Company believes this data to be accurate and to reflect qualified expert opinion regarding current research. However, Hobart Brothers Company cannot make any expressed or
implied warranty as to this information.

415889 April 30, 2009 Page 3 of 3