HART Communication Protocol Part 1

Distributed Control System
HART Communication Protocol

Part 1
Presented by:
Mr. Atul Kumar Sharma
Dept. of EICE
Engineering College Ajmer
INTRODUCTION
• HART -HIGHWAY ADDRESSABLE REMOTE TRANSDUCER

• Global standard for sending and receiving digital information across
analog wires between smart field devices and control or monitoring
systems, like PLC and DCS systems.
• Field Devices: pressure, flow, temp. transmitters, valve positioners
and actuators.
• Digital networking facility to access any instrument, field device or
controller for configuration and diagnostics from any point of the
network.
• Digital information utilizes the existing 4 mA to 20 mA network,
making it easy to deploy in new as well as existing systems.
• Accurately encode and decode in harsh and noisy conditions.
HART- Highway addressable Remote Transducer
• Introduction
• How it came
• Theory of operation
• Wiring and Installations
• Operation
• Benefits of HART Communication
• Conclusion
• References
INTRODUCTION
 It is an open source process control network that supports

Hybrid Communication.
• Provides bidirectional digital communication channel over
the same 4-20 mA wiring in half duplex mode.
• It uses 1200 baud Frequency Shift Keying (FSK) based on the
Bell 202 standard to superimpose digital information on the
conventional 4-20 mA analog signal.
• Provide flexibility not available with any other communication
technology.
• Analogus to CALLER ID.
HART
How it Came
• Earlier all installed systems in process control industries used 4-20
mA international standard for communicating process variable
information between process automation equipments.
• HART Field Communications Protocol extends this 4-20mA standard
to enhance communication with smart field instruments, without
disturbing the 4-20 mA line.
• The protocol was developed by Rosemount Inc., built off the Bell
202 early communications standard, in the mid-1980s as
proprietary digital communication protocol for their smart field
instruments. Soon it evolved into HART.
• HART communications Foundation (HCF) was made which takes the
responsibility of coordinating and supporting the open protocol
standard and manages within this framework the device
descriptions of all registered devices.
HART Communication Foundation
• It is a manufacturer-independent, not-for-profit organization

encourages widespread use of the HART technology.
• Over five million HART field instruments installed in
over 100,000 plants worldwide.
Why HART is globally acceptable?
• It is supported by all of the major vendors of process field
instrument
• Preserves present control strategies by allowing traditional 4-
20 mA signals to co-exist with digital communication on
existing two-wire loops
• It is compatible with traditional analog devices
• Provides important information for installation and
maintenance, such as Tag-IDs, measured values, range and
span data, product information and diagnostics
• It can support cabling savings through use of multidrop
networks
• Reduces operation costs, through improved management and
utilization of smart instrument networks.
Theory of Operation
• The HART protocol makes use of the Bell 202 Frequency Shift
Keying (FSK) standard to superimpose digital communication
signals at a low level on top of the 4-20mA.
• This Signal is sent over conventional wires in process
industries.
• The basic principles behind the operation of HART
instruments and networks:
– Communication Modes
– Frequency Shift Keying
– HART Networks
– HART Commands
Demonstration of HART
Theory of Operation
COMMUNICATION MODES
1. Master Slave Mode
• It is also called “Poll-Response mode”.
• During normal operation, each slave (field device) communication is
initiated by a master communication device (Controller).
• HART provides for up to two masters -primary and secondary.
• The primary master is generally a distributed control system (DCS),
programmable logic controller (PLC), or a personal computer (PC).
• The secondary master can be a handheld terminal or another PC.
Slave devices include transmitters, actuators, and controllers that
respond to commands from the primary or secondary master.
Master Slave mode
Universal Handheld Communicator
Communication Modes of HART
2. Burst Mode
• In burst mode, the master instructs the slave device to continuously
broadcast a standard HART reply message (e.g., the value of the process
variable). The master receives the message at the higher rate until it
instructs the slave to stop bursting. It is also called “Broadcast Mode”.
• It has a maximum communication speed of 3 messages/ second. It is
generally used where fast updation of the value of a measured variable is
required.
FREQUENCY SHIFT KEYING
• It is based on the Bell 202 telephone communication standard

and operates using the frequency shift keying (FSK) principle.
• The digital signal is made up of two frequencies— 1,200 Hz
and 2,200 Hz representing bits 1 and 0, respectively.
• Sine waves of these two frequencies are superimposed on the
direct current (dc) analog signal cables to provide
simultaneous analog and digital communications.
• It has a response time of approximately 2–3 data updates per
second without interrupting the analog signal.
• Masters are connected parallel to field devices, So devices
can be easily connected or disconnected and the current loop
remains uninterrupted.
Frequency Shift Keying
Cont. in next lecture

HART Communication Protocol Part 1

Uploaded by

Copyright:

Available Formats

HART Communication Protocol Part 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HART Communication Protocol Part 1

Uploaded by

Copyright:

Available Formats

What are the different communication modes used in HART protocol?

How does the HART protocol transmit digital signals over analog wires?

Distributed Control System

HART Communication Protocol

• HART -HIGHWAY ADDRESSABLE REMOTE TRANSDUCER

 It is an open source process control network that supports

• It is a manufacturer-independent, not-for-profit organization

• It is based on the Bell 202 telephone communication standard

You might also like