RADAR AND

NAVIGATIONAL AIDS

SPK.BABU
ASST. PROF
PREC, VALLAM
 What is RADAR?
The word radar is an abbreviation for RAdio Detection And
Ranging
Radar is an electromagnetic systems used for detection
and location of objects such as aircraft, ship, vehicles,
people, natural environment etc.
Radar systems use modulated waveforms and directive
antennas to transmit electromagnetic energy into a
specific volume in space to search for targets.
Objects (targets) within a search volume will reflect
portions of this energy (radar returns or echoes) back to
the radar.
These echoes are then processed (Afterwards they are
called as video signals) by the radar receiver to extract
target information such as range, velocity, angular
position, and other target identifying characteristics.
 Radar Principles
Transmitter generates and transmits
electromagnetic wave (sine or pulse).
A portion of it is reflected back by the target
(object you want to identify).
The radiated portion is collected by the radar
antenna and processed.
One antenna can be used for both transmission
and reception.
 RADAR BLOCK DIAGRAM AND
OPERATION

transmitter - oscillator, - magnetron, -" pulsed"-(turned on and

on) by the modulator to generate a repetitive train of pulses.
Example: to detect aircraft at ranges of 100 or 200 nmi you need
peak power of the order of a megawatt,
a pulse width of several microseconds,
pulse repetition frequency of several hundred pulses per second.
The waveform generated by the transmitter travels via a
transmission line to the antenna, where it is radiated into space.
A single antenna is generally used for both transmitting and
receiving.
 Duplexer
The duplexer protects the receiver from high
transmission power.
consist of two gas-discharge devices, one known
as a TR (transmit-receive) and the other an ATR
(anti-transmit-receive).
The TR protects the receiver during transmission
and the ATR directs the echo signal to the
receiver during reception.
Solid-state ferrite circulators and receiver
protectors with gas-plasma TR devices and/or
diode limiters are also employed as duplexers.
 Receiver
The receiver is usually of the superheterodyne type.
The first stage low-noise RF amplifier, such as a parametric
amplifier or a low-noise transistor.
The mixer and local oscillator (LO) convert the RF signal to an
intermediate frequency(IF).
A typical" IF amplifier for an air-surveillance radar might have a center
frequency of 30 or 60 MHz and a bandwidth of the order of one
megahertz.
The IF amplifier should be designed as a matched filter -
frequency-response function - maximize the
sigtial-to-mean-noise-power ratio
This occurs when the
magnitude of the frequency-response function = the magnitude of the
echo signal spectrum
the phase spectrum of the matched filter = negative of the phase
spectrum of the echo signal
In a radar whose signal waveform approximates a rectangular
pulse, the conventional IF filter bandpass characteristic
approximates a matched filter when the product of the IF
bandwidth B and the pulse width r is of the order of unity, that is,
Br=- 1.
 2nd Detector & Display
Demodulates the pulse modulation
Amplified by the video amplifier
Displayed on a CRT- This is a special
CRT called PPI-plan position indicator
 Display
The most common form of cathode-ray tube display is the
plan position indicator, or PPI which maps in polar
coordinates the location of the target in azimuth and
range.
This is an intensity-modulated display in which the
amplitude of the receiver output modulates the electron-
beam intensity (z axis) as the electron beam is made to
sweep outward from the center of the tube.
The beam rotates in angle in response to the antenna
position.
B-scope display is similar to the PPI except that it utilizes
rectangular, rather than polar, coordinates to display
range vs. angle.
Both the B-scope and the PPI, being intensity modulated,
have limited dynamic range.
A Scope- which plots target .amplitude axis) vs. range
axis), for some fixed direction. This is a deflection-
modulated display. It is more suited for tracking-radar
application than for surveillance radar.
Radar Frequencies
Applications of Radar
Air Traffic control
Aircraft
navigation
Ship safety
Remote Sensing
Law enforcement
Military
Range- Distance from you and the
target!
The range of the object is found by
the time the pulse takes to travel to
and from the detected object
 Maximum unambiguous range
We send a train of pulses. Not a single pulse. A pulse is
sent and reflected back as echo
We have to wait to get for the echo before we send the
next one
If not the echo for the first pulse we sent will become echo
for the second one. This is called second time around pulse
Due to this the target may look near (as you get the echo
immediately for the send pulse: this echo was for the first
pulse!!!!)
So the pulse repetition frequency (PRF) is important and it
determines the maximum unambiguous range
Run = cTp/2 = c/ 2fp
 To increase the range
Transmitted power is increased
Gain of the antenna should be high
Large antenna for reception
The receiver should be sensitive to
weak signals (should pick them)
Range equation is an important
derivation we are going to do to
calculate the range.
 Radar Equation
The radar equation relates the range of a radar to
the characteristics of the transmitter, receiver,
antenna, target, and environment.
It is useful for determining the maximum
distance from the radar to the target
it can serve both as a tool for understanding
radar operation and as a basis for radar design.
However it cannot give the precise value.
Why??
Statistical nature of noise and signal
Fluctuation & uncertainty of the target
Propagation effect of the wave
Losses
Are affecting the calculation
We will consider each one separately.
 The Radar Equation-
Considerations of various
parameters
As I pointed out earlier there are many factors
which we have to consider in the range equation.
They affect the calculation.
But we can model them and mathematically find
the model and insert in the range equation.
Noise is in the system and it is random. So we
have to have probability.
If affects the detection. So we have to get SNR
Pulse repetition frequency
Cross section of the target exposed to the wave
we send
 Detection of Signals in Noise
(MINIMUM DETECTABLE SIGNAL)

Noise affects the systems

The weakest signal which can be
detected by radar is called as
minimum detectable signal and it is
included in the radar equation.
> target is present
----- received signal----- Threshold--
< target is absent

This is called threshold detection

 Threshold detection: two problems
false alarm: if the threshold is set as low then the noise may be
detected as target
Missed detection: If the threshold is set high then real target
will be missed.
However we use matched filter which will increase the SNR.
So we conclude that SNR is an important factor and more analysis is
needed.
 Receiver Noise and the Signal-to-Noise Ratio
My aim is to find Smin and insert it in the radar equation
Most receivers are super heterodyne.
The noise is mostly internal. It is thermal or Johnson noise. Its
value is 1.38 X 10-23 J/deg. Noise figure is to be derived and
defined below
Probabilities of Detection

and Probability of False Alarm

Probability Density Functions
Below are some of the probability density functions we use in the
radar.

Examples of PDFs: a: Uniform b: Gaussian c: Raleigh voltage d:

Exponential(Raleigh power)
False alarm time
Will false alarm affect our
detection?
 Integration of Radar Pulses
This is the method of using more than one
pulse in detection
Using n pulses instead of one pulse increases
the SNR
 Fitting the gain we got into radar
equation
This is the efficiency we gain

Note: We have two

levels of detection one
is called predetection
and other is post
detection.
This integration of
pulses give more
efficiency in
predetection.

Previously the radar equation Now substituting we get

was
 Radar Cross Section of Targets

is the radar cross section.

It is the area covered and it will be proportional to the magnitude
wave reflected. So we can define this parameter in dB
Since the wave is covering a volume/ area we can define this
parameter as
power _ reflected
4R 2 | Er |2
power _ incident / 4
This power reflected can be found by solving Maxwells equation.
Radar wavelength and dimension of the target are two important
parameters which define this
If the wavelength is larger than the dimension of the target Raleigh
scattering occurs. Example rain
if the Wavelength is smaller than the target the scattering lies in the
optical region. Example aircraft
If the wavelength and the object is of same dimension then it is in
the resonance region
 Sphere:
Here the is directly proportional to f4 in resonance region
nearly equal in resonance region
very small. No scattering only a small bright spot is
seen.(if you take a photograph of a polished metal ball, you
will see only a small bright spot: not the ball)

=1

At resonance it oscillates.
Attains maximum at 2a =1

 A thin rod

Here the reflected wave(scattered

wave/echo) depends on the angle at
which the rod is viewed
Square flat plate
Large Cone Sphere
 Complex targets
Aircrafts, buildings, missiles are some examples
It depends on the viewing angle and frequency
(wavelength)
One complex target will have two or more surfaces which
scatters the incoming waveform
They can be each modeled as cone, sphere, flat or rod
shaped.
So we can calculate them individually and add them
together.
That is the reason we studied the above separately
We should also note that the phase of each signal reflected
will be different and depend on the angle
Here we see two scatters showing the change in the
magnitude with respect to change in the viewing angle
 An Aircraft
The scattering shown as polar plot.
We see more signals are reflected back when viewed along
Sideways: Flat surface
Nose and tail. Cone and sphere
Engine will modulate the echo signal.
The fluctuations in the reflected signal are low when you use
microwave frequency and high when you use low frequency.
A missile
 Radar cross Section
Fluctuations
The fluctuations are due to the following
reasons
Change in viewing angle
Individual scatters
Echo from each scatter will have different
amplitude and phase
Multiple reflections
Shadowing one scatter by another
Phase shift of more than 2*pi causes
amplitude changes
Take more scans and see the results.
This is one of the solutions.
 Four Swirling model
To study the fluctuations in detail Four Swirling model is
used
Case 1:
Each scan give constant amplitude but different correlation
This is called slow fluctuations (Scan to Scan fluctuations)
Raleigh scatters belong to this category
Case 2
Each pulse give different output
Each of them independent
Case 3:
Same as case 1 but different pdf
Case 4:
Fluctuations is pulse to pulse and same pdf as case 3
The fluctuation affect the probability of detection
Fluctuations are usually small.
We see the four cases using a diagram and we see that
case 1 will create more problems
 Inference from all the models
The probability-density function assumed in cases 1 and 2 applies
to a complex target consisting of arbitrary independent scatterers
of approximately equal echoing areas.
Although, in theory, the number of independent scatterers must
be essentially infinite, in practice the number may be as few as
four or five.
The probability-density function assumed in cases 3 and 4 is
more indicative of targets that can be represented as one large
reflector together with other small reflectors.
In all the above cases, the value of cross section to be substituted
in the radar equation is the average cross section
The signal-to-noise ratio needed to achieve a specified
probability of detection without exceeding a specified false-alarm
probability can be calculated for each model of target behavior.
For purposes of comparison, the no fluctuating cross section will
he called case 5.
A comparison
Additional SNR required for a
particular performance
PULSE REPETITION FREQUENCY AND RANGE
AMBIGUITIES
Suppose you are trying to detect the object A.
It is in unambiguous range. So we get the echo after the pulse
repetition.
If suppose there are other two objects B and C which we are not
interested, at distance above the unambiguous and twice.
The echoes from these objects will also be seen on the A scope.
Since we are integrating the pulses, we see pulses in position P1,
P2, P3 respectively.
 Solution
One method of distinguishing multiple-time-
around echoes from unambiguous echoes is to
operate with a varying pulse repetition frequency.
The echo signal from an unambiguous range
target will appear at the same place on the A-
scope on each sweep no matter whether the prf
is modulated or not.
However, echoes from multiple-time-around
targets will be spread over a finite range
 SYSTEM LOSSES
losses that occur throughout the radar system.
The losses reduce the signal-to-noise ratio at the
receiver output.
They may be of two kinds, Depending upon
whether or not they can be predicted
The antenna beam-shape loss, collapsing loss,
and losses in the microwave plumbing are
examples of losses which can be calculated.
Losses not readily subject to calculation and
which
are less predictable include 'those due to field
degradation and to operator fatigue or lack of
operator motivation.
 Plumbing loss.
i. Transmission line losses
For low frequency the losses is high
For high frequency the losses is high
So keep the distance between antenna and receiver
short as possible
The loss is taken twice as the signal is transmitted and
received
ii. Duplexer loss
It is a gas filled section used to protect the receiver form
the transmitter.
The transmitter uses very high power and receiver we
get only a small from from the reflected
So we use a waveguide shutter which produces loss it
can be upto 2dB
2. Antenna losses
Signal processing loss
 Other losses-
Equipment degradation
Field degradation.
Operator loss
 Propagation effect

The radar environment includes terrain and sea surfaces,

the atmosphere (including precipitation), and the
ionosphere. These may degrade radar observations and
performance by producing clutter and other spurious
returns, signal attenuation, and bending of the radar-signal
path.
Terrain and sea surfaces, which may produce target
masking, radar clutter, and multipath interference;
Precipitation, principally rain, which may produce signal
attenuation and clutter returns;
The troposphere, which may produce refraction that
bends the radar signal path, signal attenuation, and a lens
loss;
The ionosphere, which may produce refraction that bends
the radar signal path, signal fluctuation and attenuation,
waveform dispersion, and rotation of signal polarization.