OPTIREG™ linear TLE4476D

Dual low-drop voltage regulator

Features
• Output 1: 350 mA, 3.3 V ± 4%
• Output 2: 430 mA, 5.0 V ± 4%
• Enable input for output 2
• Low quiescent current in OFF state
• Wide operation range: up to 42 V
• Reverse battery protection: up to 42 V
• Output protected against short-circuit
• Wide temperature range: -40°C to +170°C
• Overvoltage protection up to 65 V (< 400 ms)
• Overtemperature protection
• Overload protection
• Green Product (RoHS compliant)

Potential applications
General automotive applications.

Product validation
Qualified for automotive applications. Product validation according to AEC-Q100.

Description
The TLE4476D is a monolithic integrated voltage regulator providing two output voltages, Q1 is a 3.3 V output
for loads up to 350 mA and Q2 is a 5 V output providing 430 mA. Output 2 can be switched ON/OFF via the
enable input EN. The device is available in the PG-TO252-5 (DPAK) package.
The TLE4476D is designed to supply microprocessor systems under the severe conditions of automotive
applications and is therefore equipped with additional protection functions against overload, short-circuit
and overtemperature.

Type Package Marking

TLE4476D PG-TO252-5 4476D

Datasheet Rev. 2.6

www.infineon.com/OPTIREG-linear 1 2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator

Table of Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Pin assignment PG-TO252-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Pin definitions and functions PG-TO252-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2 Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 Typical performance characteristics voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1 Application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2 Selection of external components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.1 Input, output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.2 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 Thermal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.4 Reverse-polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5 Further application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Datasheet 2 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Block diagram

1 Block diagram

1 2
I Q1

Bandgap
Reference

4
Q2

5
EN

3
GND AEB02563

Figure 1 Block diagram

Datasheet 3 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Pin configuration

2 Pin configuration

2.1 Pin assignment PG-TO252-5

GND

1 5

I EN
Q1 Q2
AEP02562

Figure 2

2.2 Pin definitions and functions PG-TO252-5

Table 1 Pin definitions and functions

Pin no. Symbol Function
1 I Input voltage
Block to GND directly at the IC with a ceramic capacitor
2 Q1 3.3 V output
Block to GND with a capacitor CQ1 ≥ 10 µF , ESR < 2 Ω at 10 kHz
3 GND Ground
4 Q2 5 V output
Block to GND with a capacitor CQ2 ≥ 10 µF , ESR < 3 Ω at 10 kHz
5 EN Enable input
Switch Q2 ON (high signal) or OFF (low signal)

Datasheet 4 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
General product characteristics

3 General product characteristics

3.1 Absolute maximum ratings

Table 2 Absolute maximum ratings

Tj = -40°C to +170°C
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
Input I
Voltage VI -42 – 42 V – P_3.1.1
Voltage VI – – 65 V t < 400 ms P_3.1.2
Current II – – – mA Internally limited P_3.1.3
3.3 V output Q1
Voltage VQ1 -1 – 36 V – P_3.1.4
Current IQ1 – – – mA Internally limited P_3.1.5
5 V output Q2
Voltage VQ2 -1 – 36 V – P_3.1.6
Current IQ2 – – – mA Internally limited P_3.1.7
Inhibit EN
Voltage VEN -42 – 42 V – P_3.1.8
Voltage VEN – – 65 V t < 400 ms P_3.1.9
Current IEN – – – mA Internally limited P_3.1.10
Temperatures
Junction temperature Tj -50 – 170 °C – P_3.1.11
Storage temperature Tstg -50 – 150 °C – P_3.1.12

Notes
1. ESD-Protection according to MIL Std. 883: ±2 kV.
2. Stresses above those listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.

3.2 Functional range

Table 3 Functional range

Parameter Symbol Values Unit Note or Number
Min. Typ. Max. Test Condition
1)
Output 1 input voltage VI1 4.5 – 42 V P_3.2.1
2)
Output 2 input voltage VI1 5.7 – 42 V P_3.2.2
3.3 V regulator IO1 0 – 350 mA – P_3.2.3
output current

Datasheet 5 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
General product characteristics

Table 3 Functional range (cont’d)

Parameter Symbol Values Unit Note or Number
Min. Typ. Max. Test Condition
5 V regulator IO2 0 – 430 mA – P_3.2.4
output current
3)
Junction temperature Tj -40 – 170 °C P_3.2.5
Thermal resistances
Junction case Rth,j-case – – 3 K/W – P_3.2.6
4)
Junction ambient Rth,j-a – – 80 K/W P_3.2.7
1) Input voltage VI required for operation of output Q1.
2) Input voltage VI required for operation of output Q2.
3) The overtemperature protection is set to > 170°C. The voltage regulator may not be operated continuously at 170°C
as device reliability will be reduced to 500 h statistical lifetime.
4) Worst case regarding peak temperature, zero airflow; mounted on a PCB 80 × 80 × 1.5 mm3, 35 µm Cu, 5 µm Sn, heat
sink area 300 mm2.

Note: In the operating range the functions given in the circuit description are fulfilled.

Datasheet 6 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Electrical characteristics

4 Electrical characteristics

Table 4 Electrical Characteristics

VI = 13.5 V; VEN > VENH; Tj = -40°C to +170°C; unless otherwise specified.
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
3.3 V output Q1
Output voltage VQ1 3.17 3.3 3.43 V 1 mA < IQ1 < 250 mA P_4.0.1
1)
Output current limitation IQ1 350 – 900 mA P_4.0.2
Load regulation ∆VQ1 – – 30 mV 1 mA < IQ1 < 250 mA P_4.0.3
Line regulation ∆VQ1 – – 20 mV IQ1 = 5 mA; 6 V < VI < 28 V P_4.0.4
2)
Power supply ripple PSRR – 60 – dB 20 Hz < fr < 20 kHz; P_4.0.5
rejection Vr = 5 Vpp
Output capacitor CQ1 10 – – µF – P_4.0.6
ESR of output capacitor RESRQ1 – – 2 Ω At 10 kHz P_4.0.7
5 V output Q2
Output voltage VQ2 4.8 5.0 5.2 V 1 mA < IQ2 < 330 mA P_4.0.8
1)
Output current limitation IQ2 430 – 900 mA P_4.0.9
1)
Drop voltage; VDRQ2 – 0.3 0.7 V IQ2 = 330 mA P_4.0.10
VDRQ2 = VI - VQ2
Load regulation ∆VQ2 – – 50 mV 5 mA < IQ2 < 330 mA P_4.0.11
Line regulation ∆VQ2 – – 50 mV IQ2 = 5 mA; 6 V < VI < 28 V P_4.0.12
2)
Power supply ripple PSRR – 60 – dB 20 Hz < fr < 20 kHz; P_4.0.13
rejection Vr = 5 Vpp
Output capacitor CQ2 10 – – µF – P_4.0.14
ESR of output capacitor RESRQ2 – – 3 Ω At 10 kHz P_4.0.15
Current consumption
Quiescent current; Iq – 100 150 µA Tj < 85°C; P_4.0.16
Iq = II - IQ1 VEN = 0 V
Quiescent current; Iq – 300 400 µA IQ1 = IQ2 = 300 µA; P_4.0.17
Iq = II - IQ1 - IQ2 Tj < 85°C
Quiescent current; Iq – 2.5 10 mA IQ1 = 150 mA; P_4.0.18
Iq = II - IQ1 - IQ2 IQ2 = 300 µA
Quiescent current; Iq – 5 13 mA IQ1 = 300 µA; P_4.0.19
Iq = II - IQ2 - IQ1 IQ2 = 250 mA
Enable input EN
EN ON voltage VEN ON 1.8 – – V VQ2 ON P_4.0.20
EN OFF voltage VEN OFF – – 1.0 V VQ2 OFF P_4.0.21
Input current VEN – 20 30 µA VEN = 13 V P_4.0.22
1) Measured when the output voltage VQ has dropped 100 mV from the nominal value.
2) Guaranteed by design.

Datasheet 7 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Electrical characteristics

4.1 Typical performance characteristics

Output current IQ1 versus Output current IQ2 versus

input voltage VI input voltage VI enable ON

AED02844 AED02845
1200 1200
mA mA
I Q1 I Q2

800 800

600 600

400 400

200 200

0 0
0 10 20 30 40 V 50 0 10 20 30 40 V 50
VI VI

Output voltage VQ2 Output voltage VQ1

versus temperature Tj versus temperature Tj

AED03039 AED03040
5.2 3.5

VQ2 VQ1
V V

5.1 3.4

Q2 Q1
5.0 3.3

4.9 3.2

4.8 3.1
-40 0 40 80 120 ˚C 160 -40 0 40 80 120 ˚C 160
Tj Tj

Datasheet 8 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Electrical characteristics

Drop voltage VDR1 versus Drop voltage VDR2 versus

output current IQ1 output current IQ2 EN ON

AED02847 AED02848
1200 600
mV mV
VDR1 VDR2
500

800 400

600 300

400 200

200 100

0 0
0 50 100 150 200 mA 250 0 100 200 300 400 mA 500
I Q1 I Q2

Current consumption Iq Current consumption Iq

versus input voltage VI versus input voltage VI

AED02849 AED02846
6 6
mA mA
Iq Iq
5 5

4 4
RL2 = 50 Ω
3 3
RL1 = 33 Ω
RL1 = 330 Ω
RL1 = 3.3 k Ω
2 2
RL2 = 100 Ω

1 1

0 0
0 10 20 30 40 V 50 0 10 20 30 40 V 50
VI VI

Datasheet 9 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Electrical characteristics

Current consumption Iq Current consumption Iq

versus output current IQ1 versus output current IQ2

AED02850 AED02851
20 30

I q mA I q mA
25

10 20

15

5 10

0 0
0 50 100 150 200 mA 250 0 100 200 300 mA 400
I Q1 I Q2

Output voltage VQ1 versus Output voltage VQ2 versus

input voltage VI input voltage VI

AED02852 AED02853
6 6
VQ1 V VQ2 V
5 5

4 4

3 3

2 2

1 1

0 0
0 5 10 15 20 V 25 0 5 10 15 20 V 25
VI VI

Datasheet 10 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Application information

5 Application information
Note: The following information is given as a hint for the implementation of the device only and shall not
be regarded as a description or warranty of a certain functionality, condition or quality of the device.

5.1 Application diagram

I Q1
5.7 - 42 V 3.3 V
CI C Q1
470 nF 22 μF

Bandgap
Reference

Q2
5V
C Q2
22 μF

e.g. from EN
Ignition

GND
AES02564

Figure 3 Application diagram

5.2 Selection of external components

5.2.1 Input, output

The input capacitor CI is necessary for compensating line influences. Using a resistor of approx. 1 Ω in series
with CI, the LC circuit of input inductivity and input capacitance can be damped. To stabilize the regulation
circuits of the stand-by and main regulator, output capacitors CQ1 and CQ2 are necessary. Stability is
guaranteed at values, CQ1 ≥ 10 µF (ESR ≤ 2 Ω) and CQ2 ≥ 10 µF (ESR ≤ 3 Ω) within the operating temperature
range.

5.2.2 Enable
Using the enable feature output 2 (5 V output) can be switched ON or OFF. The enable input can be connected
directly to terminal 30 (battery line) or 15 (ignition line). It is also possible to control the output 2 via the
microcontroller.

5.3 Further application information

For further information you may contact https://www.infineon.com.

Datasheet 11 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Package information

6 Package information

6.5 +0.15
-0.05
A
5.7 MAX.
1) 2.3 +0.05
-0.10

(5) B 0.5 +0.08

-0.04
(4.24) 1 ±0.1

0.9 +0.20
-0.01
0.8 ±0.15
6.22 -0.2
9.98 ±0.5

0...0.15

0.51 MIN.
0.15 MAX.
per side 5 x 0.6 ±0.1 0.5 +0.08
-0.04

1.14
0.1 B
4.56
0.25 M A B

1) Includes mold flashes on each side.

All metal surfaces tin plated, except area of cut.

Figure 4 PG-TO252-51)

Green Product (RoHS compliant)

To meet the world-wide customer requirements for environmentally friendly products and to be compliant
with government regulations, the device is available as a Green Product. Green Products are RoHS compliant
(Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
Further information on packages
https://www.infineon.com/packages

1) Dimensions in mm

Datasheet 14 Rev. 2.6

2023-08-07
OPTIREG™ linear TLE4476D
Dual low-drop voltage regulator
Revision history

7 Revision history

Revision Date Changes

Rev. 2.6 2023-08-07 Update template, layout, and structure
Editorial changes
Rev. 2.5 2007-03-20 Initial version of RoHS-compliant derivate of TLE4476D
Page 1: AEC certified statement added
Page 1 and Page 12: RoHS compliance statement and Green Product feature added
Page 1 and Page 12: Package changed to RoHS compliant version
Legal Disclaimer updated

Datasheet 15 Rev. 2.6

2023-08-07
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.

IMPORTANT NOTICE
Edition 2023-08-07 The information given in this document shall in no For further information on technology, delivery terms
event be regarded as a guarantee of conditions or and conditions and prices, please contact the nearest
Published by
characteristics ("Beschaffenheitsgarantie"). Infineon Technologies Office (www.infineon.com).
Infineon Technologies AG With respect to any examples, hints or any typical
81726 Munich, Germany values stated herein and/or any information regarding
the application of the product, Infineon Technologies WARNINGS
hereby disclaims any and all warranties and liabilities
© 2023 Infineon Technologies AG. of any kind, including without limitation warranties of Due to technical requirements products may contain
All Rights Reserved. non-infringement of intellectual property rights of any dangerous substances. For information on the types
third party. in question please contact your nearest Infineon
In addition, any information given in this document is Technologies office.
Do you have a question about any subject to customer's compliance with its obligations
aspect of this document? stated in this document and any applicable legal Except as otherwise explicitly approved by Infineon
Email: [email protected] requirements, norms and standards concerning Technologies in a written document signed by
customer's products and any use of the product of authorized representatives of Infineon Technologies,
Infineon Technologies in customer's applications. Infineon Technologies’ products may not be used in
The data contained in this document is exclusively any applications where a failure of the product or any
Document reference consequences of the use thereof can reasonably be
intended for technically trained staff. It is the
Z8F55296901 expected to result in personal injury.
responsibility of customer's technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to
such application.