wear parts catalog Doc. no. R 223.

1317

SANDVIK CH870:01 + CT7:01

This document is valid for:

Serial no. / Machine no. Sign.

SANDVIK CH870:01 + CT7:01

© Copyright 2008 Sandvik SRP AB.

All rights reserved. No parts of this document may be reproduced or copied in any form or by
any means without written permission from Sandvik SRP AB. All data and information in this
manual may be changed without further notice. Reservations for misprints.

Document number: R 223.1317

Issue: 20080312
Version: 1

Sandvik
Stationsplan, SE-233 81 Svedala, Sweden
Tel: +46 (0)40 409000, Fax: +46 (0)40 409260
www.sandvik.com
WPC Sandvik CH870:01 + CT7:01

General
Ordering information
When ordering parts, always state the machine type, manufacturing number,
serial number and order number according to the identification plate on the
cone crusher or tank. State quantity, article number and denomination for
each ordered part. The quantities listed in this catalog show how many pieces
of each part that are usually exchanged in a certain position.
Crusher’s and tank identification plate
The figure below shows an example of the identification plates. The
identification plates contains data needed when contacting Sandvik
concerning wear parts.
Please enter the serial number of the associated machine in the intended field
on the first page of this wear part catalog (the copyright page).

Identification plate:
1 Machine type
2 Part number
3 Serial number
4 Order number

1 2 3 4
The “Type” number is a designation system that describes the product.
Type:
1 Type and size of crusher
2 Crushing chamber (concave ring)
CH870 -EC/ A/ EC/ 50-42/ 47/ 32/ 37:01
3 Mantle
4 Filler ring
5 Gear set: 50/60 Hz 1 2 3 4 5 6 7
6 Eccentric throw (mm)
7 Mark number

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 3

WPC Sandvik CH870:01 + CT7:01

Overview with section number references

1.
2.
3.

9. 12.

13.

4.
7. 5.
6.
8.

10. 11.

4 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB

WPC Sandvik CH870:01 + CT7:01

1. Splitter (option for MF/F/EF)

7300-0 7301-0
7400-0 7302-0,-2,-3
7401-0,-1,-2
7304-0
7306-0

7303-0
7402-0,-1,-2 7305-0,-2

Cat. no. Qty. Part number Alternative Description Remarks

7400-0 1 452.2942-901 Cover Each cover consists of (see below):
7401-0 6 Screw M6S 16x45 Fasteners for cover
7401-1 6 Washer BRB 17x30
7401-2 6 Lock nut M16
7402-0 14 Screw M6S 16x50
7402-1 14 Washer BRB 17x30

Cat. no. Qty. Part number Alternative Description Remarks

7300-0 1 452.2939-901 Splitter Each splitter consists of (see below):
7301-0 2 Splitter section
7304-0 4 Splitter shoe
7306-0 4 Wearing plate
7302-0 4 Screw M6S 20x65 Fasteners for splitter parts
7302-2 8 Washer TRSB 21x58
7302-3 4 Lock nut M20
7303-0 4 Screw M6S 24x130
7305-0 16 Screw M6S 24x35
7305-2 16 Washer TRBSB 21x58

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 5

WPC Sandvik CH870:01 + CT7:01

2. Upper feed hopper wearing rubber

7505-3
7501-0
7503-0
7504-0
7502-0

7505-1,-2,-4

7505-0,-1,-2

Cat. no. Qty. Part number Alternative Description Remarks

7501-0 10 442.9747-01 Rubber segment, plain section 55 mm Standard for EC
Option for C/MC/M/MF/F/EF
7502-0 1 442.9751-02 Rubber segment, R level sensor section 55 mm
7503-0 1 442.9751-01 Rubber segment, L level sensor section 55 mm
7504-0 2 442.9750-01 Rubber segment, inspection door 55 mm
7505-0 48 840.0067-00 Screw M6S 16x45 Fasteners for rubber
segments
7505-1 112 847.0016-00 Washer BRB 17x30
7505-2 56 845.0215-00 Lock nut M16
7505-4 8 840.0070-00 Screw M6S 16x60
7505-3 56 873.1287-00 Rubber plug D45 35x40

6 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB

WPC Sandvik CH870:01 + CT7:01

3. Lower feed hopper wearing rubber

7103-0

7103-1
7103-2

7102-0
7102-2

7102-4
7102-1 7104-0
7101-0
7100-0

Cat. no. Qty. Part number Alternative Description Remarks

7100-0 6 452.0792-901 Segment support (cone) EC configuration
452.2333-901 C configuration
452.2348-901 MC configuration
7103-0 12 840.0069-00 Screw Fasteners for segment
supports
7103-1 24 847.0016-00 Washer
7103-2 12 845.0215-00 Lock nut
7104-0 4 840.0634-00 Screw M6S 16x25 Blind screw in topshell (when wearing
rubbers to filler ring are not used)
7101-0 12 452.1137-001 Rubber segment EC configuration
452.2340-901 C configuration
452.2353-001 MC configuration
7102-4 48 873.1287-00 Rubber plug Fasteners for rubber segments
7102-0 48 840.0069-00 Screw M6S 16x55
7102-1 96 847.0016-00 Washer BRB 17x30
7102-2 48 845.0215-00 Lock nut M16

5110-0

5125-0
5125-2
5125-4

Cat. no. Qty. Part number Alternative DescriThption Remarks

5110-0 2 452.1296-001 Wearing rubber M/MF/F/EF configurations (no segment
supports)
5125-0 4 840.0064-00 Screw M6S 16x30 Fasteners for wearing rubbers to filler
ring
5125-2 4 847.0016-00 Washer BRB 17x30
5125-4 4 452.1303-001 Attachment strip

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 7

WPC Sandvik CH870:01 + CT7:01

4. Spider cap

5650-0
5685-0,-2

5675-0 5655-0,-2

5150-0
5705-0
5706-1
5706-3
5706-0 5651-0
5706-2

Cat. no. Qty. Part number Alternative Description Remarks

5150-0 2 452.1060-001 Arm shield
5650-0 1 452.0553-001 Spider cap
5655-0 4 840.0653-00 Screw M6S 20x100 Fasteners for spider cap
5655-2 4 847.0132-00 Washer BRB 21x36
5651-0 1 873.1210-00 O-ring
5675-0 1 452.1619-001 Spider bushing
5685-0 8 840.0652-00 Screw M6S 20x90 Fasteners for spider bushing
5685-2 8 847.0132-00 Washer BRB 21x36
5705-0 1 452.1599-001 Spider bushing seal ring
5706-0 1 452.1599-001 Seal ring
5706-1 1 452.0550-001 Ring
5706-2 1 452.0549-001 Retaining ring
5706-3 8 841.0225-00 Screw MC6S 6x45 Fasteners for spider bushing seal ring,
seal ring, ring, and retaining ring

8 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB

WPC Sandvik CH870:01 + CT7:01

5. Head nut

4205-0

4025-0 4205-2

4205-1

Cat. no. Qty. Part number Alternative Description Remarks

4025-0 1 452.0505-001 Mainshaft sleeve
4205-0 1 452.0936-901 Head nut with burning ring
4205-1 1 452.0930-001 Inner head nut
4205-2 1 452.0938-001 Burning ring

6. Support ring
6020-1
6020-2
6020-8
6020-4
6020-0

6105-0 6050-0

Cat. no. Qty. Part number Alternative Description Remarks

6020-0 6 840.1136-00 Screw M6S 36x540 Fasteners for concave, to
support ring and topshell
6020-1 6 845.0273-00 Lock nut M36
6020-2 6 442.9353-01 Sleeve
6020-4 6 442.9354-01 Washer
6020-8 72 863.0015-00 Disc spring
6050-0 1 452.0687-001 Support ring
6105-0 6 442.8290-01 Dowel Dowel for support ring

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 9

WPC Sandvik CH870:01 + CT7:01

7. Liners

6008-0

6007-5
6008-2
6007-0,-1,-2

6008-1
6006-0

6005-0

4175-0

Cat. no. Qty. Part number Alternative Description Remarks

6008-0 4 452.0710-901 Wearing plate For short concave (MF/F/EF)
6008-1 8 840.0069-00 Screw 16x55 Fasteners for wearing plates
6008-2 8 847.0060-00 Washer TRSB 17x42
6006-0 1 452.0891-901 Filler ring EC For concave EC
452.2269-901 Filler ring C For concave C/MC
452.0898-901 Filler ring M For concave M/MF/F/EF
6007-0 10 840.0675-00 Screw N6S 24x130 Fasteners for filler ring
6007-1 10 899.0293-00 Tray M24x1.5D
6007-2 10 847.0063-00 Washer TRSB 26x65
6007-5 8 452.2201-00 Jacking screw M6S 24x80
6005-0 1 452.0838-001 EC Concave See section 6. “Support ring” for
fasteners
452.2253-001 C
452.2253-001 MC
452.1754-001 M
452.0842-001 MF
452.0841-001 F
452.0840-001 EF
4175-0 1 452.0837-001 Mantle A For concave EC/C/MC/M
452.0872-001 Mantle B Pebble For concave EC/C/MC/M
452.0845-001 Mantle EF For concave MF/F/EF

(Continued)

10 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB

WPC Sandvik CH870:01 + CT7:01

Feed hopper Crushing chamber

w.p. Filler ring 6006-0 Concave 6005-0 Mantle 4175-0

EC extra coarse 452.0891-901 EC extra coarse 452.0838-001

(442.9747-01,442.9751-01,

Segment support
Rubber segments
standard 7101-0

(452.0792-901)
442.9751-02)

7100-0

C coarse 452.2255-001 A 452.0837-001

Segment support

(452.2333-901)
7100-0

C coarse 452.2269-901
Wearing plate
not available

not available
Splitter

MC medium coarse 452.2253-001 B Pebble 452.0872-001

Segment support

(452.2348-901)
7100-0

M medium 452.1754-001
(442.9747-01,442.9751-01,442.9751-02)
Rubber segments
option 7101-0

MF medium fine 452.0842-001

M medium 452.0898-901
Wearing rubber

(452.1296-001
5110-0

F fine 452.0841-001 EF extra fine 452.0845-001

standard 6008-0
(452.0710-901)
Wearing plate
option 7300-0
Splitter

EF extra fine 452.0840-001

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 11

WPC Sandvik CH870:01 + CT7:01

8. Dust sealing

4305-0
4350-0
4355-1

4365-1 4365-0,-2
4355-0
Cat. no. Qty. Part number Alternative Description Remarks
4305-0 1 452.0924-001 Dust seal ring
4350-0 1 452.0921-001 Retaining ring
4355-1 1 452.1264-001 Scraper
4365-0 15 840.0069-00 Screw M6S 16x55 Fasteners for dust sealing and scraper
4365-2 16 847.0016-00 Washer BRB 17x30
4365-1 1 840.0072-00 Screw M6S 16x70
4355-0 1 442.9367-01 Retaining plate

9. Bottomshell wearing liners

1320-7
1320-6
1320-1 1010-2
1320-2

1010-1

1320-3
1320-5
1320-4
Cat. no. Qty. Part number Alternative Description Remarks
1010-1 1 452.1066-901 Pin shaft arm liner Arm liners
1010-2 3 452.1065-901 Narrow arm liner
1320-1 6 452.1191-901 Wearing plates Sold as a complete set
1320-2 2
1320-3 4
1320-6 2
1320-7 2
1320-4 16
1320-5 4

12 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB

WPC Sandvik CH870:01 + CT7:01

10. Step bearing set

Cat. no. Qty. Part number Alternative Description Remarks

1 1 452.2630-901 Step bearing set Consists of (top to bottom):

4075-0 1 Mainshaft step

2280-0 1 Step washer
2260-0 1 Piston wearing plate

11. Chevron packing

2305-0

Cat. no. Qty. Part number Alternative Description Remarks

2305-0 1 452.0986-901 Chevron packing

12. Hydroset

Cat. no. Qty. Part number Alternative Description Remarks

1 1 912.0129-00 Filter cartridge Hydroset oil system

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 13

WPC Sandvik CH870:01 + CT7:01

13. Lubrication and over-pressure system

Cat. no. Qty. Part number Alternative Description Remarks

1 2 912.0222-00 Filter cartridge Main lubrication system
2 1 912.0114-00 Filter cartridge Pinionshaft lubrication system
3 1 452.1308-901 Oil strainer
4 1 452.1166-001 Over-pressure air filter cartridge

14 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB

WPC Sandvik CH870:01 + CT7:01

14. Toolbox
Qty Part number Description Remarks
1 452.1247-901 Lifting tool Eccentric bushing
452.1246-901 Lifting tool Bottomshell bushing
442.9446-00 Lifting tool Piston wearing plate, step washer
452.0452-001 Lifting tool Scraper ring
452.1512-901 Piston stop plate Holding piston
840.0692-00 Screw M6S 30x100 Piston stop plate
442.7284-90 Lowering rod M16x900 Mainshaft step
843.1529-00 Lowering rod M30x1000 Piston
845.0013-00 Nut M6M 30 8 Lowering rod M30x1000
899.0336-00 Eye bolt LT M80 Mainshaft
899.0032-00 Eye bolt LT M30 Hydroset cylinder cover
899.0031-00 Eye bolt LT M24 Filler ring
899.0160-00 Eye bolt M20 Spider bushing, (ECC.unit)
899.0147-00 Eye bolt LT M16 Dust collar, piston, support ring, ecc.bush.
899.0155-00 Eye bolt LT M12 Bottomshell bushing, piston wear plate, main-
shaft sleeve
899.0099-00 Eye bolt LT M10 Hydroset cylinder bushing, pinion
899.0244-00 Eye bolt LT M8 Inner head nut
920.0110-00 Ring spanner striking 65 mm Screw and nut M42
920.0109-00 Ring spanner striking 55 mm Screw and nut M36
920.0238-00 Ring spanner striking 46 mm Screw M30
920.0243-00 U-ring spanner 55 mm Screw and nut M36
920.0131-00 U-ring spanner 46 mm Screw and nut M30
920.0135-00 U-ring spanner 36 mm Screw and nut M24
920.0134-00 U-ring spanner 30 mm Screw and nut M20
920.0022-00 U-ring spanner 24 mm Screw and nut M16
920.0244-00 U-ring spanner 18 mm Screw and nut M12
920.0245-00 U-ring spanner 16 mm Screw and nut M10
920.0042-00 Socket screw key 19 Screw MC6S 24
920.0040-00 Socket screw key 14 Screw MC6S 16
920.0038-00 Socket screw key 10 Screw MC6S 12
920.0037-00 Socket screw key 8 Screw MC6S 10
920.0035-00 Socket screw key 5 Air bleeder valve
920.0032-00 Socket screw key 5/8" Plug, spider cap
442.0800-91 Chunk of lead Check of closed side setting
923.0422-00 Feeler gauges 0,05-1 mm Spider bearing play, etc.

© 2008 Sandvik SRP AB Doc. no. R 223.1317 Ver. 1 15

WPC Sandvik CH870:01 + CT7:01

This page is intentionally left blank

16 Doc. no. R 223.1317 Ver. 1 © 2008 Sandvik SRP AB