Scribd Logo
Upload

Welcome to Scribd!

  • 105 views

    Bulletin 1047

    Uploaded by

    Cesar Casachagua Davila
    This service bulletin describes new backlash measuring tools released for the MP800 and MP1000 product lines. The tools are used to measure the backlash, or circumferential motion, between the countershaft pinion gear and eccentric gear. Acceptable backlash ranges are provided in tables. If backlash is outside the range, shims must be added or removed from under the lower thrust bearing. The tools can be obtained through local Metso Minerals representatives.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Bulletin 1047

    Uploaded by

    Cesar Casachagua Davila
    105 views2 pages
    This service bulletin describes new backlash measuring tools released for the MP800 and MP1000 product lines. The tools are used to measure the backlash, or circumferential motion, between the countershaft pinion gear and eccentric gear. Acceptable backlash ranges are provided in tables. If backlash is outside the range, shims must be added or removed from under the lower thrust bearing. The tools can be obtained through local Metso Minerals representatives.

    Original Title

    Bulletin1047

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This service bulletin describes new backlash measuring tools released for the MP800 and MP1000 product lines. The tools are used to measure the backlash, or circumferential motion, between the countershaft pinion gear and eccentric gear. Acceptable backlash ranges are provided in tables. If backlash is outside the range, shims must be added or removed from under the lower thrust bearing. The tools can be obtained through local Metso Minerals representatives.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    105 views2 pages

    Bulletin 1047

    Uploaded by

    Cesar Casachagua Davila
    This service bulletin describes new backlash measuring tools released for the MP800 and MP1000 product lines. The tools are used to measure the backlash, or circumferential motion, between the countershaft pinion gear and eccentric gear. Acceptable backlash ranges are provided in tables. If backlash is outside the range, shims must be added or removed from under the lower thrust bearing. The tools can be obtained through local Metso Minerals representatives.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Service Bulletin 1047

    Bulletin type: Service Bulletin Product line: MP Series


    Distribution: Extranet Product type: MP800, MP1000
    Status: Approved Module: Gear
    Serial number range or
    list:

    Subject
    Release of Backlash Measuring Tools

    Body
    Tools have been created for the MP800 (MM0263920) and for the MP1000 (MM0263921) to measure
    the backlash between the countershaft pinion gear and the eccentric gear.

    The figure above shows a Backlash Measuring Tool. The tool is designed to fit over the end of the
    counter shaft where it exits the side of the Crusher. The fit of the tool on the shaft is very close so the
    end of the shaft, as well as the keyway, must be clean and free of burrs. It also helps to use some
    light oil to ease the tool on and off the shaft. The figure above shows that the tool has two lines near
    the end of the handle that mark the pinion pitch diameter of spiral bevel pinion gears and straight
    bevel pinion gears. The tool is used to measure the circumferential motion, due to the backlash
    between the pinion gear and the eccentric gear, at the pinion pitch diameter mark that corresponds
    with the type of gear set that was provided with your Crusher. Then compare the amount of
    circumferential motion to the allowable range given in the tables below. It is common practice to set
    the backlash at the high end of the acceptable range. A displacement gauge can be used to measure
    the amount of circumferential motion, measured perpendicular to the surface of the handle directly
    above the location of the pinion pitch diameter mark for the type of gear set provided with your
    Crusher. If the backlash is less than or greater than the acceptable range, shims must be added or
    removed from under the Lower Thrust Bearing. See your Instruction manual for proper procedures for
    making this adjustment. If in the process of lowering the eccentric in order to reduce the backlash on
    a worn set of gears, the root clearance reaches the minimum limit, the root clearance will then be the
    limiting factor to assure that the teeth do not bottom out.
    The backlash measuring tool for the MP800 (MM0263920) or the MP1000 (MM0263921) is available
    through your local Metso Minerals representative.

    Attachments

    Created by Joey Karczewski


    Approved by Jeff Lawnicki/31/10/2008

    You might also like