Powertrain: Caterpillar Machine Price List

The Educational Services Commission of New Jersey Grounds Equipment Bid #ESCNJ 18/19-25
Caterpillar Price Pages 1/2/19 -Wheel Loader 988K NJ State Approved Co-op #65MCESCCPS
CATERPILLAR MACHINE PRICE LIST

988K
988K WHEEL LOADER Ship Weight LIST PRICE
DECATUR, IL, USA lbs AT DEALER
Standard Equipment:
-Fuel level
POWERTRAIN -Hydraulic oil temperature
Advanced Productivity Electronic Control -Speedometer/Tachometer
Shifting (APECS) -Torque convertor temperature
Air to air aftercooler Instrumentation, warning indicators:
Brakes, full hydraulic, enclosed, wet -Action alert system, three category
multiple disc service brakes -Axle/Brake oil temperature (front/rear)
Electro hydraulic parking brake -Brake oil pressure
Engine, Cat C18 w/ACERT technology -Electrical system, low voltage
Fuel priming pump (electric) -Engine failure malfunction alert and
Fuel to air cooler action lamp
Ground level engine shutoff Mirrors, rearview (externally mounted)
Guard, transmission Parking brake status
Hydraulically driven demand fan Rimpull select switch
Integrated braking Seat, Cat Comfort (cloth) air suspension
Radiator, Next Generation Modular (NGMR) STIC control system with steering lock
Separated cooling system Tinted glass
Starting aid (ether) automatic Transmission gear (indicator)
Throttle lock Product Link Elite:
Torque converter, impeller clutch with -VIMS
lock-up clutch & rimpull control system -Graphical information display
Turbine precleaner, engine air intake -External data port
Transmission, planetary powershift, -Customizable operator profiles
4F/3R electronic control Wet-arm wipers/washers (front and rear),
intermittent wipers (front and rear)
ELECTRICAL
Alarm, back-up OTHER STANDARD EQUIPMENT
Alternator, 150-amp Automatic bucket tilt/lift kickouts
Batteries, maintenance-free, 4-1000 CCA electronically adjustable from cab
Converter, 10/15-amp, 24V to 12V Counterweight
Lights, front & rear, access stairway, Doors, service access (locking)
turn signals Ecology drains for engine, radiator,
Starter, electric (heavy duty) hydraulic tank
Starter lockout in bumper Economy mode with on demand throttle
Starting receptacle for emergency start Emergency platform egress
Transmission lockout in bumper Engine, crankcase, 250 hour interval
with CJ-4 oil
OPERATOR ENVIRONMENT Engine idle management features:
Air conditioner -Auto idle kickdown
Cab, sound-suppressed, pressurized, -Delayed engine shutdown
internal four-post rollover protective -Engine idle shutdown
structure (ROPS/FOPS), radio ready for Fuel tank, 731 L (188 gal)
entertainment includes antenna, Ground level fuel fill
speakers, converter (12-volt 10/15-amp) Ground level transmission electronic
and power port clutch pressure control access
Coat and hard hat hooks Hitch, drawbar with pin
E/H tilt & lift controls (seat mounted) Hoses, Cat XT(TM)
Flip-up armrest Hydraulic oil cooler
Heater and defroster Hydraulic, steering and brake
Horn, electric filtration/screening system
Implement hydraulic lockout Oil sampling valves
Laminated glass Stairway, left and right rear access
Light, dome (cab) Steering, load sensing
Lunchbox and beverage holders Toe kicks
Instrumentation, gauges: Vandalism protection caplocks
-Engine coolant temperature
Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

Caterpillar: Confidential Green Printed in USA
US-A-19-01 A U. S. DOLLAR CURRENCY 988K-001
1 Bid Term: 2/20/19 - 2/19/21


988K
OTHER STANDARD EQUIPMENT (CONT.)

Venturi stack

2 Bid Term: 2/20/19 - 2/19/21


988K
347-5000 988K WHEEL LOADER HRC ............................. 101,021 $904,750

LANE 2 - AVAILABLE FROM DECATUR FACTORY
LANE 3 - AVAILABLE FROM DECATUR FACTORY
AVAILABLE FOR: AM-N, EU, ISRAEL, JAPAN, & SOUTH KOREA
0P-4742 988K MISCELLANEOUS MATERIAL ..............................0 NC

AVAILABLE FROM DECATUR FACTORY
Only reference numbers under the Factory Sourced Kits section can be
used on a MISC order.

3 Bid Term: 2/20/19 - 2/19/21


988K
REF Ship Weight LIST PRICE
USE NO. LANE 2 / 3 MANDATORY lbs AT DEALER
LANE SELECTION
0P-9002 LANE 2 ORDER ........................................ 0 NC
0P-9003 LANE 3 ORDER ........................................ 0 NC
SPECIAL ARRANGEMENTS
LOADER ARRANGEMENTS
L 367-2710 LOADER, STANDARD ................................... 0 NC
REQUIRES: 347-5000 988K WHEEL LOADER HRC
467-5822 or 467-5833 CPM PAYLOAD WEIGHING
L 367-2730 LOADER, BLOCK HANDLER .......................... 17,879 $31,010
FOR USE WITH LANE 3 ONLY
Specialized machine for block handling applications. Includes larger
lift and tilt cylinders, and extra counterweight. Other attachments
that can complement this offering are ride control and axle oil
cooler.
367-2726 LIFT,STANDARD 3V,BLOCK HANDLER
424-6490 LUBRICATION or 424-6495 AUTOLUBE
347-4940 ENGINE, BRAKE
42PR or ** Tires with HLA Rims
L 367-2720 LOADER, MILLYARD ............................... 18,729 $40,150
Specialized machine for log loading millyard applications. Includes
larger lift and tilt cylinders, extra counterweight, swing out
radiator system with wider fin spacing and auto-reversing fan. Other
attachments that can complement this offering are ride control and
axle oil cooler.
367-2705 LIFT, STANDARD 3V, MILLYARD
424-6490 LUBRICATION or 424-6495 AUTOLUBE
550-0284 LIGHTS, LED (MY, SM)
360-8193 CAMERA, REAR VISION
42PR or ** Tires with HLA Rims

4 Bid Term: 2/20/19 - 2/19/21


988K
SPECIAL ARRANGEMENTS (CONT.)

LOADER ARRANGEMENTS (Cont.)
L 552-0032 LOADER, STEEL MILL ................................... 0 $34,950
Specialized machine for steel mill slag handling applications.
Includes transmission and parking brake override systems, steel roof,
stainless steel braided hose guarding (refer to TEKQ1464), reinforced
platform to accommodate fire suppression systems, brake accumulator
guard, solid metal access ladders, swing out radiator system with wide
fin spacing and auto-reversing fan. Ecosafe oil is recommended.
367-2715 LIFT, STANDARD or 367-2725 LIFT, HIGH
548-2125 LUBRICATION or 548-2130 or 548-2135 AUTOLUBE
550-0284 LIGHTS, LED (MY, SM)
523-6588 CAB, STEEL MILL
441-5220 MIRRORS, STANDARD (SM)
360-8193 CAMERA, REAR VISION
519-9951 FUEL TANK, STANDARD (SM)
435-1155 GUARDS, HEAVY DUTY
541-7900 COOLER, AXLE OIL (MY, SM) or 435-1223 GUARD
557-9861 KIT, AXLE OSCILLATION STOP
L 367-2750 LOADER, EZ CLEAN ..................................... 0 $21,350
Provides reversing fan feature, lower cooling fin density, and easy
core cleaning access.
472-7125 or 516-3924 LIFT, EZ CLEAN
BOOMS, STICKS, AND LINKAGES

LIFT ARRANGEMENTS
Please pay attention to compatibility, it is dependent on Loader
selection.
L 347-4900 LIFT, STANDARD 2V ....................................0 NC

Provides standard lift with 2-valve function.
Recommended for use with Load and Carry applications, loading 30/40
ton off highway trucks.
ONLY FOR USE WITH: 367-2710 or 367-2719 LOADER, STANDARD
L 347-4910 LIFT, STANDARD 3V .................................. 442 $9,030
Provides standard lift with 3-valve function.
Recommended for use with Load and Carry applications, loading 30/40
ton off highway trucks.
L 347-4920 LIFT, HIGH 2V ...................................... 950 $7,960
Provides high lift with 2-valve function.
Recommended for loading 50/70 ton trucks or any application where
maximum dump clearance is desired.

5 Bid Term: 2/20/19 - 2/19/21


988K
BOOMS, STICKS, AND LINKAGES (CONT.)

LIFT ARRANGEMENTS (Cont.)
L 347-4930 LIFT, HIGH 3V .................................... 1,393 $17,000
Provides high lift with 3-valve function.
Recommended for loading 50/70 ton trucks or any application where
maximum dump clearance is desired.
L 367-2726 LIFT,STANDARD 3V,BLOCK HANDLER ................... 7,811 $9,030
Provides standard lift height linkage with application specific
design, tilt lever guard, and 3V hydraulics.
ONLY FOR USE WITH: 367-2730 or 367-2739 LOADER, BLOCK HANDLER
L 367-2705 LIFT, STANDARD 3V, MILLYARD ....................... 7,620 $9,030
Provides standard lift height linkage with application specific design
and 3V hydraulics.
ONLY FOR USE WITH: 367-2720 or 367-2729 LOADER, MILLYARD
L 367-2715 LIFT, STANDARD 2V, STEEL MILL ...................... 5,016 $1,445
Provides standard lift linkage with 2V hydraulics and rear bumper
with side guards.
ONLY FOR USE WITH: 552-0032 or 552-0034 LOADER, STEEL MILL
L 367-2725 LIFT, HIGH 2V, STEEL MILL .......................... 7,813 $9,400
Provides high lift linkage with 2V hydraulics and rear bumper with
side guards.
L 472-7125 LIFT, STANDARD 2V, EZ CLEAN ........................... 0 $3,450
ONLY FOR USE WITH: 367-2750 LOADER, EZ CLEAN
L 516-3924 LIFT, HIGH 2V, EZ CLEAN ................................ 0 $11,400
ONLY FOR USE WITH: 367-2750 LOADER, EZ CLEAN
LUBRICATION ARRANGEMENTS
The autolube option provides a LINCOLN INDUSTRIAL CORP. "CENTROMATIC"
automatic greasing system for 18 lube locations requiring lubrication
on the Lift Ar. This arrangement is powered using hydraulic oil for
trouble free performance and includes a 60 lb. reservoir. Special
guarding is added when needed to protect lines or valve components.
Tank or reservoir can be filled from a remote location at ground
level or at the tank port.
Please pay attention to compatibility, it is dependent on Lift

selection.
L 367-5610 LUBRICATION, STANDARD ............................... 0 NC

ONLY FOR USE WITH: LIFT, STANDARD or LIFT, HIGH
L 367-5580 AUTOLUBE, CENTROMATIC ............................. 393 $15,960
ONLY FOR USE WITH: LIFT, STANDARD
L 367-5585 AUTOLUBE, CENTROMATIC ............................. 409 $15,960
ONLY FOR USE WITH: LIFT, HIGH

6 Bid Term: 2/20/19 - 2/19/21


988K
BOOMS, STICKS, AND LINKAGES (CONT.)

LUBRICATION ARRANGEMENTS (Cont.)
L 424-6490 LUBRICATION, STANDARD (BH, MY) ...................... 21 NC
ONLY FOR USE WITH: 367-2726 LIFT,STANDARD 3V,BLOCK HANDLER
L 424-6495 AUTOLUBE, CENTROMATIC (BH, MY) ..................... 459 $15,960
ONLY FOR USE WITH: 367-2726 LIFT,STANDARD 3V,BLOCK HANDLER
L 548-2125 LUBRICATION, STANDARD (SM) ........................... 0 NC
ONLY FOR USE WITH: 367-2715 LIFT, STANDARD 2V, STEEL MILL
367-2725 LIFT, HIGH 2V, STEEL MILL
L 548-2130 AUTOLUBE, CENTROMATIC (SM) .......................... 0 $15,960
ONLY FOR USE WITH: 367-2715 LIFT, STANDARD 2V, STEEL MILL
L 548-2135 AUTOLUBE, CENTROMATIC (SM) .......................... 0 $15,960
ONLY FOR USE WITH: 367-2725 LIFT, HIGH 2V, STEEL MILL
POWERTRAIN
ENGINE ARRANGEMENTS
L 366-1928 ENGINE, STANDARD .................................... 0 NC
US EPA T4F/EU Stage V Technology
ONLY FOR USE WITH: 347-5000 988K WHEEL LOADER HRC
CANNOT BE USED WITH: 367-2730 LOADER, BLOCK HANDLER
L 347-4940 ENGINE, BRAKE .......................................78 $2,900
US EPA T4F/EU Stage V Technology
Provies engine braking for steep grades or speed reduction.
ENGINE PRECLEANERS
L 377-9320 PRECLEANER, STANDARD................................ 0 NC
L 377-0851 PRECLEANER, DUAL.................................... 37 $2,795
AXLE ARRANGEMENTS
L 347-5246 AXLES, STANDARD ..................................... 0 NC
Provides standard front and rear axles.
L 347-5256 AXLES, NO-SPIN REAR .................................-15 $4,780
Provides standard front axle and no-spin rear axle. With normal hard
packed floor conditions this can cause significant tire wear.
No-spin recommended in applications which require improved traction.
CANNOT BE USED WITH: 552-0032 or 552-0034 LOADER, STEEL MILL

7 Bid Term: 2/20/19 - 2/19/21


988K
SUSPENSION SYSTEMS
RIDE CONTROL
The ride control option provides a suspension system by placing two
accumulators in the lift circuit. Manual off and automatic mode
selection. In auto mode the suspension system engages when reaching
preset value. It reduces bounce caused by bucket-induced loads when
traveling loaded or unloaded. For use in high speed roading, load and
carry, and any other application in which load retention, bucket
spillage, or operator ride may be a problem. This option is ideal for
government bid specifications.
L 347-4973 NO RIDE CONTROL ..................................... 0 NC
L 478-3882 RIDE CONTROL...................................... 252 $9,980

Axle oil cooler is recommended with ride control attachment and any
high braking applications.
AVAILABLE FOR: ALL REGIONS EXCEPT EU
L 478-3884 RIDE CONTROL (EU) .................................. 252 $9,980
AVAILABLE FOR: ALL REGIONS EXCEPT CANADA
L 541-7880 RIDE CONTROL (SM) .................................... 0 $12,900
L 541-7890 RIDE CONTROL (SM) (EU) ................................ 0 $12,900
HYDRAULICS
L 470-5053 ACCUMULATORS....................................... 0 NC
L 470-5043 ACCUMULATORS (EU) ................................... 0 NC
LINE GROUPS
STEERING
L 376-6936 STEERING, STANDARD .................................. 0 NC
L 376-6937 STEERING, SECONDARY ............................... 135 $8,460
Provides a ground speed driven supplemental steering pump.

8 Bid Term: 2/20/19 - 2/19/21


988K
ELECTRICAL
LIGHTS
L 345-0538 LIGHTS, STANDARD .................................... 0 NC
Provides the following:
Front flood/running lights (4 Halogen/all facing forward)
Rear flood lights (4 Halogen/all facing rear) and 2 taillights
Upper ROPS lights (6 Halogen/2 facing rear and 4 facing forward)
CANNOT BE USED WITH: 367-2720 or 367-2729 LOADER, MILLYARD
552-0032 or 552-0034 LOADER, STEEL MILL
L 360-8184 LIGHTS, HID ......................................... 28 $2,535
Standard front flood/running lights (4 Halogen/all facing forward)
Rear flood lights (2 HID/4 Halogen/all facing rear) and 2 taillights
Upper ROPS lights (4 HID/facing forward and 4 Halogen/2 facing
rear and 2 facing forward)
L 550-0283 LIGHTS, LED .......................................... 0 $3,855
Front flood/running lights (4 LED/all facing forward)
Rear flood lights (4 LED/all facing rear) and 2 taillights
Upper ROPS lights (8 LED/2 facing rear and 6 facing forward)
L 550-0284 LIGHTS, LED (MY, SM) ................................. 0 $5,160
Front flood/running lights (4 LED/all facing forward)
Rear flood lights (4 LED/all facing rear) and 2 taillights
Upper ROPS lights (8 LED/2 facing rear and 6 facing forward)
OPERATOR ENVIRONMENT
CAB PACKAGES
NOTE: 2-point seat belts are standard. 4-point seat belts are
available through parts distribution if needed.
L 540-2511 CAB, BASIC .......................................... 0 $3,170

INCLUDES:
-Cab door, standard window (LH)
-Cab glass, standard
-Cab precleaner, non-powered
-Seat, heated & ventilated
-Seat belt, 3", 2-point, minder
-Radio, CB (ready)

9 Bid Term: 2/20/19 - 2/19/21


988K
OPERATOR ENVIRONMENT (CONT.)

CAB PACKAGES (Cont.)
L 540-2512 CAB, BASIC PLUS ...................................... 0 $4,290
INCLUDES:
-Cab door, sliding window (LH)
-Cab glass, standard
-Cab precleaner, non-powered
-Radio, CB (ready)
L 544-1162 CAB, DELUXE ......................................... 0 $14,040
INCLUDES:
-Cab door, standard window (LH)
-Cab glass, rubber mounted
-Cab precleaner, powered
-Radio, CB (ready)
L 523-6588 CAB, STEEL MILL ...................................... 0 $11,770
INCLUDES:
-Cab door, standard window (LH) (SM)
-Cab glass, rubber mounted
-Cab precleaner, powered
-Seat, standard
-Radio, CB (ready)
MIRRORS
L 346-3864 MIRRORS, STANDARD ................................... 0 NC
L 376-7034 MIRRORS, HEATED ..................................... 6 $119
L 441-5220 MIRRORS, STANDARD (SM) ............................. 14 NC
Provides mirrors with metal back for steel mill applications.
INTEGRATED OBJECT DETECTION SYSTEM

L 360-8191 CAMERA, REAR VISION .................................. 0 NC
Provides an object detection system (camera only) to enhance operator
awareness of surroundings. This system uses visual information only
in order to provide the operator with additional information about
the work area to the rear of the wheel loader.
367-2730 or 367-2739 LOADER, BLOCK HANDLER

10 Bid Term: 2/20/19 - 2/19/21


988K
OPERATOR ENVIRONMENT (CONT.)

INTEGRATED OBJECT DETECTION SYSTEM (Cont.)
L 360-8193 CAMERA, REAR VISION .................................. 0 NC
Provides an object detection system (camera only) to enhance operat
awareness of surroundings. This system uses visual information only
in order to provide the operator with additional information about
the work area to the rear of the wheel loader.
367-2750 LOADER, EZ CLEAN
L 372-3042 DETECTION, OBJECT (RADAR) ........................... 19 $2,795
Not available for EU.
Provides an object detection system (camera & radar) to enhance
operator awareness of surroundings. This system uses visual and
radar information in order to provide the operator with additional
information about the work area to the rear of the wheel loader.
For a list of countries that RF radar is approved for use in, visit
https://dealer.cat.com/detect
TECHNOLOGY PRODUCTS
PRODUCT LINK
Product Link enables the remote transmission of information about the
location, operation, and condition of your equipment. Efficiently and
effectively monitor performance of your assets to help keep your jobs
on schedule, maintain equipment condition, and reduce the costs of
owning and operating your fleet.
Authorization varies by country, please reference

https://Dealer.cat.com/PL/Certification for certified countries.
Please contact your Caterpillar marketing representative with
questions.
L 509-4155 PRODUCT LINK, CELLULAR PLE641 ......................... 0 NC

Product Link Elite series PLE641 offers expanded coverage including
3G UMTS and CDMA2000 as well as 2G GSM and CDMA cellular networks to
transmit location, utilization and condition information for viewing
in Product Links remote monitoring web interface. Cellular technology
provides capabilities for frequent transmission and larger volumes of
data.
L 509-4150 PRODUCT LINK, SATELLITE PLE631 ......................... 0 $432
Product Link Elite series PLE631 uses a satellite network to transmit
location, utilization and condition information for viewing in Product
Links remote monitoring web interface. For use in areas with poor or
no cellular coverage.
FUEL SYSTEMS
FUEL TANKS
L 519-9949 FUEL TANK, NON-FAST FILL .............................. 0 NC

11 Bid Term: 2/20/19 - 2/19/21


988K
FUEL SYSTEMS (CONT.)

FUEL TANKS (Cont.)
L 519-9950 FUEL TANK, FAST FILL .................................. 0 $1,930
Provides fast fill adaption with automatic shutoff.
L 519-9951 FUEL TANK, STEEL MILL ................................. 0 $2,235
Provides thicker wall fuel tank without fast fill receiver port for
steel mill applications.
FUEL LINES
L 433-3842 FUEL LINES, NON-HEATED ................................ 0 NC
L 433-3843 FUEL LINES, HEATED ...................................16 $1,030
TIRES, RIMS, AND WHEELS
Due to industry-wide tire availability limitations, tire brand and

type cannot be guaranteed. Every effort will be made to satisfy your
tire choice. However, if the tire type cannot be supplied we will
contact the dealer to propose alternatives. The dealer needs to choose
between an alternative tire or a "rims only" option (where available)
within 72 hours. If no response is provided by the deadline, the order
will default to the alternative tire and will be changed at that
point. As a consequence of a possible tire change, the total machine
price will be decreased or increased depending on the price of the new
tire.
NOTE: All tires are tubeless, include heavy duty rims and come in a
set of 4.
NOTE: 42PR tires may be used to improve lateral stability. Recommended

for use with uneven floors and/or high truck loading heights with
dense materials.
NOTE: Tires with HLA rims have tires mounted on rims for Heavy Load
Applications. These are required for machines in block handler and
millyard applications and any other application where higher loads may
be encountered.
NOTE: Block Handler and Millyard orders require 42PR or ** tires with
HLA rims.

12 Bid Term: 2/20/19 - 2/19/21


988K
TIRES, RIMS, AND WHEELS (CONT.)

TIRES AVAILABLE FROM BRIDGESTONE
P 490-7503 TIRES, 35/65-33 BS 42PR L5 ............................. 0 $8,180
Bridgestone Bias DL; Tread Depth=97mm (122/32"); Rim=28"x33" 4 piece
Suitable for severe rock environments where maximum damage protection
is needed.
CANNOT BE USED WITH: Block Handler or Millyard orders
P 452-4111 TIRES, 35/65-33 BS 42PR L5 HLA ...................... 6,210 $13,980
Same tire as above, but with Heavy Load Application rims.
HLA rims are required for block handler and millyard applications and
any other application where higher loads may be encountered.
P 490-7504 TIRES, 35/65R33 BS VSNT ** L4 .......................... 0 $-1,240
Bridgestone Radial; Tread Depth=62.5mm (79/32"); Rim=28"x33" 4 piece
Provides damage resistance, mobility, and traction in moderate rock
environments.
P 493-6840 TIRES, 35/65R33 BS ** L4 HLA ............................0 $4,560
P 499-5790 TIRES, 35/65R33 BS VSDL ** L5 ....................... 2,772 $13,320
Bridgestone Radial; Tread Depth=95mm (120/32"); Rim=28"x33"
is needed.
P 452-4118 TIRES, 35/65R33 BS ** L5 HLA ........................ 1,610 $25,240
Bridgestone Radial VSDL IDU with Heavy Load Application rims.
TIRES AVAILABLE FROM GOODYEAR

P 480-9750 TIRES, 35/65R33 GY RT-5D ** L5 .......................... 0 $21,790
Goodyear Radial; Tread Depth=98mm (123/32"); Rim=28"x33"
is needed.
P 480-9751 TIRES, 35/65R33 GY ** L5 HLA ........................... 0 $27,590
TIRES AVAILABLE FROM MICHELIN

P 396-4288 TIRES, 35/65R33 MX ** L5 ............................... 0 $32,380
Michelin Radial XMINED2; Tread Depth=97mm (122/32"); Rim=28"x33"
Directional tire suitable for severe rock environments where maximum
damage protection is needed.
P 478-4157 TIRES, 35/65R33 MX *** L4 .............................. 0 $10,080
Michelin Radial XTXL; Tread Depth=60mm (76/32"); Rim=28"x33"
Directional tire that provides damage resistance, mobility, and
traction in moderate rock environments.

13 Bid Term: 2/20/19 - 2/19/21


988K
TIRES, RIMS, AND WHEELS (CONT.)

TIRES, ALLOWANCE FOR OMISSION
P 396-4156 RIMS ONLY, TIRES OMITTED .........................-7,964 $-38,340
P 442-6345 RIMS ONLY (HLA), TIRES OMITTED ................... -9,152 $-32,540
Provides Heavy Load Application rims. HLA rims are required for
machines in block handler and millyard applications and any other
application where higher loads may be encountered.
OTHER ATTACHMENTS
SOUND SUPPRESSION
L 347-5105 NO SOUND SUPPRESSION ................................ 0 NC
Operator sound pressure level: 72 dB(A) per ISO 6396
Machine sound power level: 111 dB(A) per ISO 6395
CANNOT BE USED WITH: 141-5066 EU CERTIFICATION
L 347-5125 SOUND SUPPRESSION................................. 298 $4,880
Operator sound pressure level: 72 dB(A) per ISO 6396
Machine sound power level: 109 dB(A) per ISO 6395
REQUIRES: 435-1165 GUARD, BOTTOM
372-9038 GUARD, CRANKCASE
WHEEL CHOCKS
L 541-8669 NO WHEEL CHOCKS .................................... 0 NC
ONLY FOR USE WITH: 367-2710 or 367-2719 LOADER, STANDARD or
L 541-8671 NO WHEEL CHOCKS (EZ CLEAN) ........................... 0 NC
ONLY FOR USE WITH: 367-2720 or 367-2729 LOADER, MILLYARD or
L 0P-4780 NO WHEEL CHOCKS (SM) ................................ 0 NC
L 541-8670 WHEEL CHOCKS ....................................... 0 $1,700
Includes wheel chocks and an integrated storage system.
REQUIRES: 143-3604 MIRRORS, HANDRAIL MOUNTED
FLUIDS
HYDRAULIC OIL
L 435-1144 HYDRAULIC OIL, STANDARD .............................. 0 NC
L 435-1164 HYDRAULIC OIL, ARCTIC ................................ 89 $6,236

Installs 0W-20 CAT TDTO Cold Weather Oil in place of standard
10W HYDO-10 hydraulic oil. For use in cold climates for ambient
temperature down to -40C (-40F).
L 435-1154 HYDRAULIC OIL, ECOSAFE .............................. 89 $3,750
Installs EcoSafe FR46 hydraulic fluid.

14 Bid Term: 2/20/19 - 2/19/21


988K
USE NO. LANE 2 / 3 OPTIONAL lbs AT DEALER
SPECIAL ARRANGEMENTS
L 367-5432 COOLER, AXLE OIL ................................... 405 $11,200

Axle oil cooler attachment is recommended with ride control for long
downhill grades or any high braking applications.
L 541-7900 COOLER, AXLE OIL ..................................... 0 $10,320
Axle oil cooler attachment for use with the swing out fan system
included in the steel mill and millyard loaders.
L 435-1223 GUARD, HYDRAULIC TANK .............................. 19 $146
Required for and only for steel mill orders when not ordering axle oil
cooler.
STARTERS, BATTERIES, & ALTERNATORS

STARTING ARRANGEMENT
L 374-6450 STARTING, COLD WEATHER ............................. 94 $1,730
Includes 1 additional starter and 2 additional batteries.
STARTING AIDS
L 374-7404 HEATER, ENGINE COOLANT, 120V ......................... 1 $353
110/120-volt external power source required.
ELECTRICAL
L 376-7128 LIGHT, WARNING (LED STROBE) .......................... 17 $700

***DEALER INSTALLED ATTACHMENT***
OPERATOR ENVIRONMENT
L 504-5735 RADIO, AM/FM/AUX .................................... 0 $735
L 376-7135 RADIO, AM/FM/AUX/USB/BT/CD/SAT ....................... 6 $1,630

BlueTooth radio technology enables the use of a hands free function
such as listening to music and making phone calls.
Authorization varies by country, please contact your Cat marketing
representative with questions or click on the link below:
https://dealer.cat.com/en/products/technology.html
Requires service contract with satellite radio provider.
L 346-3863 VISOR, CAB .......................................... 2 $171
L 143-3604 MIRRORS, HANDRAIL MOUNTED .......................... 26 $595

Provides rear view outboard handrail mounted mirrors.
REQUIRED BY: 541-8670 WHEEL CHOCKS

15 Bid Term: 2/20/19 - 2/19/21


988K
TECHNOLOGY PRODUCTS
SOFTWARE ENABLED ATTACHMENTS (SEA) INSTRUCTIONS

Technology apps are activated by Software Enabled Attachments (SEA).
SEAs are available factory installed or can be purchased for dealer
installation.
Refer to Information Release Memo (IRM) EES03 -01 (media number

PELJ0138) in the Caterpillar Media Information Center for further
explanation of SEAs. Select the Product Support tab and search for
number PELJ0138. Refer to REHS1238 & REHS8401 for how to obtain a
Factory Level Password. Contact FPS: Internet with Corporate Web
Security (CWS) (https:// fps.cat.com/).
CAT PRODUCTION MEASUREMENT (CPM) PAYLOAD WEIGHING SYSTEM

Cat Production Measurement (CPM) includes an integrated onboard
payload weighing scale. This measures and/or records:
-Payload weight, material ID, truck ID, cycle (bucket dumps) count
and fuel consumption
-Allows on-the-go weighing of the bucket payload during the lift
cycle
-Daily payload total (tonnes/tons), productivity (tonnes/hour or
tons/hour) and efficiency (tonnes/liter or tons/gal) data is
reported wirelessly via Product Link to the VisionLink fleet
management web portal (Cat Essentials Product Link subscription
required).
-Detailed payload, productivity & efficiency data can be downloaded
to a laptop computer for analysis in the optional VIMSpc software
(VIMSpc & VIMS data cable are required, but VIMS is NOT required.)
-Payload tickets can be printed with an optional printer
Refer to the Cat Connect Payload Technologies intranet page

(https://dealer.cat.com/payload) for complete technical
specifications; operation, sales, marketing and technical support
publications.
NOTES:
1) Demo and permanent software are available from the factory.
2) For field installation, permanent software can be purchased
through the Caterpillar Feature Protection System and enabled by
a dealer technician with Cat ET and an SEA password.
SEA p/n 433-2014. Consult ANTARES parts distribution system for
latest SEA price.
3) Both demo and permanent software require calibration prior to
customer use.
CALIBRATION INSTRUCTIONS
This app requires calibration and set-up by either the dealer or
customer. Refer to the Systems Operation Test & Adjust manual
UENR7119 for system calibration, material and truck ID lists set-up
and operation instructions.

16 Bid Term: 2/20/19 - 2/19/21


988K
TECHNOLOGY PRODUCTS (CONT.)

L 467-5822 CPM PAYLOAD WEIGHING READY .......................... 0 NC
Includes hardware and demo software for CPM, dealer enabled for
up to 250 hours. To activate demo software, it must be enabled by
a dealer technician with Cat ET. No password is required.
For permanent software activation in the field, purchase of software
is required. See note 2 above for details.
CANNOT BE USED WITH: 367-2720 OR 367-2729 LOADER, MILLYARD
L 467-5833 CPM PAYLOAD WEIGHING ................................0 $6,180
Includes hardware and permanent software for CPM. Software is
factory enabled, but the system must be calibrated prior to customer
use. See note above for calibration instructions.
CANNOT BE USED WITH: 367-2720 OR 367-2729 LOADER, MILLYARD
L 378-8634 PRINTER, PAYLOAD .................................... 5 $2,460
Provides onboard ticket printing capability for Cat Production
Measurement (CPM).
COOLING
L 347-5185 COOLING, HIGH AMBIENT ................................ 0 NC

Provides increased air flow through software.
Recommended for ambient temperatures up to 50C (122F).
TIRES, RIMS, AND WHEELS

TIRE PRESSURE MONITORING SYSTEM
L 543-7141 MONITORING, TIRE PRESSURE............................. 0 $3,000
Provides four sensors that mount to the valve stem of each tire along
with a receiver module that monitors both pressure and temperature in
each tire. Tire pressure and temperature information is shared with
the operator via the info display. Warnings are provided through
Unified Fleet if pressure is outside of a configurable target range.
The system is not recommended for use on tires with liquid additives
or sealants.
GUARDS
L 435-1165 GUARD, BOTTOM .................................... 104 $3,020

INCLUDED IN: 435-1155 GUARDS, HEAVY DUTY
REQUIRED BY: 347-5125 SOUND SUPPRESSION
347-4919 SOUND SUPPRESSION
L 372-9038 GUARD, CRANKCASE..................................107 $715

REQUIRED BY: 347-5125 SOUND SUPPRESSION
347-4919 SOUND SUPPRESSION
L 347-5138 GUARD, STEERING CYLINDER ........................... 103 $1,295

REQUIRED BY: 141-5066 EU CERTIFICATION

17 Bid Term: 2/20/19 - 2/19/21


988K
GUARDS (CONT.)
L 435-1155 GUARDS, HEAVY DUTY ............................... 589 $4,790
Includes a front guard and tilt cylinder rod guard, in addition to
the guards below:
435-1165 GUARD, BOTTOM
372-9038 GUARD, CRANKCASE
347-5138 GUARD, STEERING CYLINDER
REQUIRED BY: 552-0032 or 552-0034 LOADER, STEEL MILL
OTHER ATTACHMENTS
MISCELLANEOUS ATTACHMENTS
L 459-6446 COVER, INLET GRILL (CW) ............................... 0 $3,585
Provides inlet grill covers for extended idling in cold weather.
Recommended for ambient temperatures of -10C (14F) and below.
ONLY FOR USE WITH: 347-5000 988K WHEEL LOADER HRC and
367-2710 LOADER, STD or 367-2730 LOADER, BH
L 347-5028 FENDERS, ROADING .................................. 315 $5,090
Provides full coverage front and rear fenders.
L 376-1572 OIL CHANGE SYSTEM, HIGH SPEED ........................ 5 $585
Provides remote port and components for high speed oil change.
AGGREGATE HANDLER
L 481-3972 AGGREGATE HANDLER, STD LIFT .......................... 0 $13,770
Provides additional counterweight for the Aggregate Handler, which
allows customers to maximize machine payload in re-handling
applications. Reference salesgram TEKQ1233-01.
REQUIRES: 347-4900 LIFT, STANDARD 2V or
347-4910 LIFT, STANDARD 3V or
472-7125 LIFT, STANDARD 2V, EZ CLEAN and
GENERAL PURPOSE or COAL BUCKET
L 481-3973 AGGREGATE HANDLER, HIGH LIFT .......................... 0 $21,210
REQUIRES: 347-4920 LIFT, HIGH 2V or
347-4930 LIFT, HIGH 3V or
516-3924 LIFT, HIGH 2V, EZ CLEAN and
GENERAL PURPOSE or COAL BUCKET

18 Bid Term: 2/20/19 - 2/19/21


988K
BUCKETS
For questions on buckets intended for Machine Orders please contact

your Marketing Subsidiary Machine Coordinator.
Loose buckets should be ordered on a MISC Order through Caterpillar

Work Tools - Wamego using source code 0P-0672. For availability of
loose buckets please email [email protected].
If you are going to order a loose bucket from CWTS and a machine from
Aurora and if you need them shipped at the same time then you need to
cross-reference the MSOs with each other.
"GET" is NOT automatically included on bucket orders. "GET" must be

entered on the order with your bucket selection, unless text for
bucket states otherwise. Please make the "GET" selection from the
"GET" listed immediately following the bucket listing. Rock bucket
selections list "GET" for spade or straight edge.
Material density will determine the appropriate capacity bucket.

Refer to the Specalog. Exceeding maximum payload may cause loader
instability.
All listed Maximum Recommended Material Densities are based on the

maximum gross weight that the 988K is rated for minus the weight of
the bucket and all required G.E.T. at 100% fill factor.
EXPORT ORDERS - If you are ordering a LOADER, STANDARD & BUCKET, then
you must order your BUCKET as Not Installed (NI).
GENERAL PURPOSE BUCKETS

Use for excavating and bank loading material requiring breakout force
as well as stockpile / rehandling applications. Includes casted corner
in sidebar for Corner Guard System GET.
P 347-4980 BUCKET-GP, 152" 9.00 YD3 ......................... 10,007 $47,653

10,007 $47,653 NI
Maximum Recommended Material Density: 1660 kg/m3 (2800 lb/yd3)
6.7M3(8.7YD3) w/bolt-on adapters, K110, 3988mm (157") wide
6.9M3(9.0YD3) w/bolt-on adapters & segments, K110, 3988mm (157") wide
6.9M3(9.0YD3) w/bolt-on cutting edge system, 3962mm (156") wide
P 347-4990 BUCKET-GP, 152" 10.00YD3 ......................... 10,536 $50,201
10,536 $50,201 NI

19 Bid Term: 2/20/19 - 2/19/21


988K
BUCKETS (CONT.)
GENERAL PURPOSE BUCKETS (Cont.)
P 435-4029 BUCKET-GP, 152" 11.00 YD3 ......................... 11,005 $51,649
11,005 $51,649 NI
P 472-0120 BUCKET-GP, 152" 12.50YD3 ......................... 11,828 $55,761
11,828 $55,761 NI
REQUIRES: 481-3972 AGGREGATE HANDLER, STD LIFT or
481-3973 AGGREGATE HANDLER, HIGH LIFT
GET for GENERAL PURPOSE BUCKETS

(includes mounting hardware)
P 208-5262 CUTTING EDGE, BOLT-ON ............................ 1,103 $2,736

40mm thick w/40mm end bits
P 174-7950 GUARD, CORNER..................................... 304 $1,057
REQUIRES: 208-5262 CUTTING EDGE, BOLT-ON
P 232-0167 ADAPTERS, BOLT ON, SET OF 8 ........................ 555 $3,968
45mm thick
ONLY FOR USE WITH: K110 tips
P 217-4652 SEGMENTS, BOLT-ON, SET OF 7 ........................ 695 $1,897
45mm thick. Use with STRAIGHT buckets.
ONLY FOR USE WITH: K110 adapters and tips
P 309-1123 TIP, PENETRATION .................................... 23 $128
Recommended for harder-to-penetrate, moderate impact, low-to-moderate
abrasive materials. Very good penetration, less wear material.
ONLY FOR USE WITH: K110 adapters
P 309-1127 TIP, GENERAL DUTY ................................... 26 $129
Recommended for general application in moderate impact and abrasive
conditions. Good penetration, (2) self-sharpening cavities.
P 309-1122 TIP, EXTRA DUTY ..................................... 36 $163
Recommended for general applications requiring more wear material in
moderate-to-high impact conditions. Good wear material, good
penetration.

20 Bid Term: 2/20/19 - 2/19/21


988K
BUCKETS (CONT.)
ROCK BUCKETS
Use for bank or face loading in most tough digging conditions.
For GCN1 dealers only:

Buckets in this section need to be ordered through a separate CMOPS
order to CWTS, even if required for a new machine order. Please
include the machine MSO on your bucket order. Please communicate with
your local Sales Rep to confirm bucket price before placing your order
into the system.
P 498-9988 BUCKET-ROCK, 158" 8.30YD3........................ 10,781 $65,307

10,781 $65,307 NI
SPADE EDGE
INCLUDES: (8) weld-on double strap Advansys adapters, outer side wear
plates, and 35mm bolt-on heel plates.
OPTIONAL: sidebar protectors and base edge wear plates
REQUIRES: (8) Advansys 130 tips and (1) segment group
P 498-9990 BUCKET-ROCK, 158" 9.00YD3 ........................ 11,120 $67,390
11,120 $67,390 NI
SPADE EDGE
INCLUDES: (8) weld-on double strap Advansys adapters, outer side wear
P 498-9992 BUCKET-ROCK, 158" 10.00YD3....................... 11,627 $70,728
11,627 $70,728 NI
SPADE EDGE
INCLUDES: (8) double strap Advansys adapters, outer side wear
GET for ROCK BUCKETS

P 109-9051 SEGMENT, BOLT-ON,SET OF 7 .......................... 807 $2,232

40mm thick. Use with SPADE buckets.
P 107-3533 SEGMENTS,HD, BOLT-ON, SET OF 7 ..................... 884 $2,460
45mm thick. Use with SPADE buckets.
P 124-6346 SEGMENTS,H.A.,BOLT-ON,SET OF 7 ...................... 805 $2,679
45mm thick, Half Arrow. Use with SPADE buckets.
P 232-0161 SEGMENTS,H.A.,BOLT-ON,SET OF 7 ...................... 966 $2,849
50mm thick base edges, Half Arrow. Use with SPADE buckets.
Includes 45mm thick half-arrow protectors and top-mounted wear plates.
P 381-4095 TIP, HEAVY PENETRATION .............................. 65 $350
ONLY FOR USE WITH: Advansys 130 adapters
P 381-4096 TIP, HEAVY ABRASION ................................. 68 $379
P 368-3791 TIP, HEAVY DUTY .................................... 57 $290
P 368-3857 TIP, HVY DUTY LONG LIFE (ARM) ........................ 59 $521

21 Bid Term: 2/20/19 - 2/19/21


988K
BUCKETS (CONT.)
GET for ROCK BUCKETS (Cont.)
P 486-6524 TIP HEAVY ABR LONG LIFE (ARM) ........................ 69 $682
P 368-3859 TIP, SHORT ......................................... 45 $197
P 381-4094 TIP, GENERAL DUTY ................................... 51 $228
P 368-3860 TIP, COAL .......................................... 44 $197
P 356-6437 PROTECTORS, SIDEBAR, SET OF 2 ....................... 106 $1,118
Set of two, one for RH and one for LH side of the bucket.
ONLY FOR USE WITH: ROCK BUCKETS ONLY
P 494-8224 PROTECTORS, SIDEBAR, SET OF 4 ....................... 212 $2,265
Set of four, two for RH and two for LH side of the bucket.
ONLY FOR USE WITH: ROCK BUCKETS ONLY
P 364-6636 PLATE GP-WEAR ..................................... 195 $535
Bolt-On Bottom, Rear Base Edge Wear Plates
25mm Thick Wear Plate
HEAVY DUTY ROCK BUCKETS

Use for bank or face loading in high abrasion and moderate impact
conditions.
P 498-9994 BUCKET-ROCK, 160" 8.30YD3........................ 14,072 $78,378

14,072 $78,378 NI
SPADE EDGE
INCLUDES: (8) weld-on double strap Advansys adapters, cutting edge
with weld-on base edge end protection, floor liner, radius liner,
inside and outside wear plates, (1) 45mm bolt-on half arrow segment
group, 25mm bolt-on base edge bottom wear plates, (2) sets of sidebar
protectors and wings (rock deflectors).
REQUIRES: (8) Advansys 130 tips
HEAVY DUTY GRANITE BUCKETS

P 498-9996 BUCKET-ROCK, 157" 8.30YD3........................ 16,455 $90,776
16,455 $90,776 NI
SPADE EDGE
INCLUDES: (7) weld-on Advansys 130 flushmount adapters on a 64mm thick
cutting edge with weld-on base edge end protection adapter covers,
full shell liner, inside and outside wear plates, bolt-on top cutting
edge protection, (1) 45mm bolt-on half arrow segment group with top
covers, 25mm bolt-on base edge bottom wear plates, heel shrouds,
(2) sets of sidebar protectors, 30-Series MAWPs for bottom wear
protection and a stronger rock guard design.

22 Bid Term: 2/20/19 - 2/19/21


988K
BUCKETS (CONT.)
IRON ORE BUCKETS
P 498-9998 BUCKET-ROCK, 154" 6.20YD3 ........................ 12,767 $69,969
12,767 $69,969 NI
Iron ore design w/ lower capacity
SPADE EDGE
INCLUDES: (7) weld-on Advansys 130 double strap adapters on a 64mm
thick cutting edge with weld-on base edge end protection floor liner,
radius liner, inside and outside wear plates, (1) 75mm bolt-on half
arrow segment group, 22mm bolt-on base edge bottom wear plates,
35mm weld-on heel plates, (2) sets of sidebar protectors
GET for HD ROCK / HD GRANITE / IRON ORE BUCKETS

P 381-4095 TIP, HEAVY PENETRATION .............................. 65 $350

Recommended for high abrasive and impact conditions, especially shot
rock. Excellent penetration and wear material.
P 381-4096 TIP, HEAVY ABRASION ................................. 68 $379
Recommended for high abrasive, moderate impact, easier-to-penetrate
materials. Excellent wear material, less penetration.
ONLY FOR USE WITH: Advansys 130 Adapters
SERRATED EDGE BUCKETS

P 416-5162 BUCKET-ROCK, 156" 9.0 YD3 ........................ 12,421 $62,107
12,421 $62,107 NI
SERRATED V-SPADE EDGE
P 428-9115 BUCKET-ROCK, 156" 8.30 YD3 ....................... 12,026 $60,007
12,026 $60,007 NI
SERRATED V-SPADE EDGE
COAL BUCKETS
P 433-4750 BUCKET-COAL, 162" 15.0 YD3 ....................... 13,278 $50,029
13,278 $50,029 NI
STRAIGHT EDGE
INCLUDES: Bolt-On Cutting Edge (BOCE)
P 433-4740 BUCKET-COAL, 162" 17.0 YD3 ....................... 14,186 $56,558
14,186 $56,558 NI
STRAIGHT EDGE
INCLUDES: Bolt-On Cutting Edge (BOCE)

23 Bid Term: 2/20/19 - 2/19/21


988K
BUCKETS (CONT.)
SPECIAL APPLICATION BUCKETS
P 421-6100 BUCKET-SLAG, 159" 8.30 YD3 ....................... 18,638 $76,415
18,638 $76,415 NI
SPADE EDGE
INCLUDES: Weld-on serrated spade edge segments and half arrow sidebar
protection
P 435-1810 BUCKET-SLAG, 154" 7.00 YD3 ....................... 16,828 $71,540
16,828 $71,540 NI
Straight edge with J600 double strap adapters
INCLUDES: (8) J600 double strap adapters, weld-on half arrow
segments, weld-on sidebar protection and full paddleplate design
REQUIRES: (8) J600 tips
GET for SPECIAL APPLICATION BUCKETS

P 6I-6420 TIP, ABRASION, HEAVY DUTY .......................... 125 $561
ONLY FOR USE WITH: J600 adapters and 335-7160 SLAG BUCKET ONLY
FLUIDS
ANTIFREEZE
Standard machine includes antifreeze protection to -34C (-29F).
Different lubricants are also required for extreme temperatures.
Please refer to operation and maintenance manual.
P 0P-2411 COOLANT, -50C (-58F) ..................................0 $520 NET
FACTORY SOURCED KITS

OBJECT DETECTION KITS
Please consult the DETECTCAT retrofit price list for dealer installed
Object Detection kits on Large Wheel Loaders.

24 Bid Term: 2/20/19 - 2/19/21


988K
FACTORY SOURCED KITS (CONT.)

RETRO-FIT KITS for CURRENT 988K
If ordering on a MISC MSO, you need to use 0P-4742 for TOP LEVEL and
0P-0812 for PACKING.
Kits must be ordered as NOT-INSTALLED.
No returns on Kit components or for parts removed.
C 557-9861 KIT, AXLE OSCILLATION STOP ............................ 0 $367 NI

988K Ser# TWX00001 & up, T8E00001 & up, LWX00001 & up, L8X00001 & up
Provides clearance to accommodate L5 slick tires or machines equipped
with tire chains. Limits rear axle oscillation to +/- 6 degrees.
REQUIRED BY: 552-0032 or 552-0034 LOADER, STEEL MILL
C 560-2915 KIT, TIRE PRESSURE MONITORING .......................... 0 $3,125 NI

Provides four sensors that mount to the valve stem of each tire along
with a receiver module that monitors both pressure and temperature in
each tire. Tire pressure and temperature information is shared with
the operator via the primary display. Warnings are provided through
Unified Fleet if pressure is outside of a configurable target range.
Software license for Cat Tire Pressure Monitoring (TPM) will be a
separate charge. Requires SEA for permanent activation.
C 563-3197 KIT, WHEEL CHOCKS ................................... 0 $1,980 NI
Provides all parts for field installation of wheel chocks and an
integrated storage system.
C 516-3925 KIT, TIRE HANDLER (SL) ................................. 0 $32,890 NI
Provides additional counterweight for tire handler applications.
CANNOT BE USED WITH: BUCKETS
C 513-5313 KIT, AGGREGATE HANDLER (SL) ........................... 0 $13,772 NI
ONLY FOR USE WITH: Standard Lift, 2 Star or 42PR Tires, & GP Bucket
C 513-5314 KIT, AGGREGATE HANDLER (HL) ........................... 0 $21,206 NI
ONLY FOR USE WITH: High Lift, 2 Star or 42PR Tires, & GP Bucket
C 498-9814 KIT, RIDE CONTROL (STANDARD) .......................... 0 $10,600 NI
Provides all parts for field installation of the ride control system.
Accumulators meet Canadian pressure vessel requirements.

25 Bid Term: 2/20/19 - 2/19/21


988K

RETRO-FIT KITS for CURRENT 988K (Cont.)
C 471-9675 KIT, COVER, INLET GRILL (CW) ............................0 $3,940 NI
988K Ser# TWX00001 & up, T8E00001 & up
Provides all parts for field installation of the inlet grill covers
for extended idling in cold weather.
Recommended for ambient temperatures of -10C (14F) and below.
Requires standard or block handler configs, not compatible with the
millyard or steel mill configs.
C 450-9894 KIT, AUTOLUBE ...................................... 95 $16,970 NI
988K Ser# TWX00001-1171, LWX00001-737
Provides all parts, including hardware and guarding, for field
installation of the Lincoln autolube centromatic system. This kit is
universal for all boom lengths.
C 521-5061 KIT, AUTOLUBE ....................................... 0 $16,970 NI
Provides all parts, including hardware and guarding, for field
installation of the Lincoln autolube centromatic system. This kit is
universal for all boom lengths.
C 450-9895 KIT, CPM PAYLOAD .................................... 5 $1,395 NI
988K Ser# TWX00001-738, LWX0001 & up
Provides all parts for field installation of the CPM system.
For latest software info, see SEPD1989 for more details.
NOTE: This kit will require a one time password charge of LP $4,148.30
Instructions for obtaining this password will be provided with
the special instructions included with this kit.
C 450-9896 KIT, THIRD VALVE ................................... 435 $9,600 NI

Provides all parts for field installation of the third valve system.
C 476-9627 KIT, SECONDARY STEERING .............................. 0 $8,990 NI
Provides all parts for field installation of secondary steering.
C 476-9606 KIT, AXLE OIL COOLER .................................. 0 $10,690 NI
Provides all parts for field installation of the axle oil cooler
system.
C 458-3099 KIT, ROADING FENDERS ................................. 0 $5,600 NI
Provides all parts for field installation of roading fenders.
C 476-9647 KIT, ENGINE PRECLEANER (DUAL) .......................... 0 $3,080 NI
988K Ser# TWX00001 & up, T8E00001 & up
Provides all parts for field installation of dual engine precleaner.
C 458-3103 KIT, CAB PRECLEANER (POWERED) ......................... 0 $7,120 NI
Provides all parts for field installation of powered cab precleaner.

26 Bid Term: 2/20/19 - 2/19/21


988K

COMMAND FOR LOADING KIT
Command for loading enables remote operation of the Cat 988K. In order
to promote safety with minimal impact to productivity, Command for
loading removes the operator from the cab of a machine. The Command
for loading Operator Console utilizes seamless integration of new
on-board hardware with familiar controls to allow the operator to have
full functionality of the machine from a safe distance. Command for
loading is currently compatible with 988K. The Operator Console is
extremely portable and is carried using a shoulder harness.
SOFTWARE ENABLED ATTACHMENT (SEA)
When quoting always include the price of the Software Enabled

Attachment (SEA) even though it is not ordered at the same time
as the installation kits. The on-board systems will not function
until the SEA is activated. Once the system is installed,
activation requires dealer support through Caterpillar
Electronic Technician (Dealer Version), communication adapter,
and authority to request factory passwords form the Caterpillar
Factory Password System (FPS).
When the factory password is generated at the request of the

service technician, a purchase order will automatically be
generated in the ANTARES system by FPS.
Refer to Information Release Memo (IRM) EES03-01 (PELJ0138) in

the Global Sales Library (GSL) for further explanation of SEAs.
Refer to RESH1238 for how to obtain a Factory Level Password
from https://fps.cat.com/.
SEAs cannot be ordered directly in ANTARES. They can only be ordered

using the Factory Password System (see instructions above).
WARNING: If you order directly in ANTARES, you may get invoiced twice.
P SEA, COMMAND LOADING LP ............................. 0 $42,760 NET

Required to enable the remote operation Command for Loading on-board
system. One is required per machine installation.
BASE ON BOARD INSTALLATION KIT

The following field retrofit kit includes: on-cab lighting,
electronics bay, wiring harness, bumper lockout service panel, and
mounting hardware.
P 516-3920 KIT, ON-BOARD INSTALLTION ............................. 0 $10,280 NI

NET
988K Ser# TWX00001 & up, T8E00001 & up
Includes REHSXXXX Special Instruction (English only).
REQUIRES: 1 OF 2 BELOW FROM PARTS DEPARTMENT:
545-8018 KIT, CONSOLE INSTALL (2.4GHZ) or
545-8019 KIT, CONSOLE INSTALL (900MHZ)

27 Bid Term: 2/20/19 - 2/19/21


988K

OPERATOR CONTROL KITS
The new Gen 3 console is designed to easily transfer control between
machines that are equipped with Command for loading. In addition, the
Gen 3 console has improved ergonomics, battery life, and
serviceability. Gen 3 consoles are available in two frequency ranges:
900 MHz (902-928 MHz) or 2.4 GHz (2403.1-2478.6 MHz) to provide site
and/or country specific requirement.
Approved countries:
900 MHz: United States and Canada.

2.4 GHz: United States Canada, Australia, New Zealand, Peru, Chile,
Columbia, Mongolia, Brazil, Mexico, Indonesia, Russia, European Union,
Japan, China, Ukraine, South Africa, Democratic Republic of the Congo,
and Saudi Arabia.
For the latest approved country listing, please visit:

https://dealer.cat.com/cda/layout?m=423015&x=7&id=2678888
The following Generation 3 Console kits contain one operator console,

two rechargeable Lithium Ion console batteries, one DC battery
charger, one AC battery charger, shoulder harness, 3 smart cards with
pouch, system carrying case, Operations and Maintenance Manual, Quick
Reference Guide, Trouble Shooting Guide, and Special Instructions.
NOTE:
The ON-BOARD INSTALLTION KIT is available from the factory only.
The CONSOLE INSTALL KITS are available from parts department only.
P 545-8018 KIT, CONSOLE INSTALL (2.4 GHZ) ......................... 0 $17,390 NI

NET
P 545-8019 KIT, CONSOLE INSTALL (900 GHZ) .........................0 $17,390 NI

NET
INSTRUCTIONS
P 504-1365 FILM, AM-NORTH ...................................... 0 NC

REQUIRED BY: AM-NORTH
P 347-5045 FILMS, ANSI .......................................... 0 NC

ONLY FOR USE WITH: 347-5000 988K WHEEL LOADER
REQUIRED BY: AM-NORTH EXCEPT QUEBEC (N050)

28 Bid Term: 2/20/19 - 2/19/21


988K
PACKING
MUST SELECT ONE
0P-0294 PACK, DOMESTIC TRUCK ................................ 0 NC

Complete machine loaded on truck.
CANNOT BE USED WITH: Tire Omission
0P-0201 DOMESTIC TRUCK, TIRE REMOVAL ......................... 0 $610 NET
Removes tires/rims.
CANNOT BE USED WITH: Tire Omission
0P-2829 PACK, DOMESTIC TRUCK ................................ 0 $262 NET
Complete machine loaded on truck.
ONLY FOR USE WITH: Tire Omission
0P-0812 PACK, MISC SHIPMENTS ................................. 0 NC
Use this as the packing reference number on a MISC MSO.
TRANSPORT GROUP
P 451-7913 TRANSPORT, BUCKET (NI) / OMIT ......................... 0 NC
Required when ordering a Not Installed (NI) Bucket on your machine
order or when omitting a Bucket from your machine order.

29 Bid Term: 2/20/19 - 2/19/21

Powertrain: Caterpillar Machine Price List

Uploaded by

Copyright:

Available Formats

Powertrain: Caterpillar Machine Price List

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Powertrain: Caterpillar Machine Price List

Uploaded by

Copyright:

Available Formats

The Educational Services Commission of New Jersey Grounds Equipment Bid #ESCNJ 18/19-25

CATERPILLAR MACHINE PRICE LIST

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

1 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

OTHER STANDARD EQUIPMENT (CONT.)

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

2 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

347-5000 988K WHEEL LOADER HRC ............................. 101,021 $904,750

AVAILABLE FOR: AM-N, EU, ISRAEL, JAPAN, & SOUTH KOREA

0P-4742 988K MISCELLANEOUS MATERIAL ..............................0 NC

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

3 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

0P-9002 LANE 2 ORDER ........................................ 0 NC

0P-9003 LANE 3 ORDER ........................................ 0 NC

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

4 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

SPECIAL ARRANGEMENTS (CONT.)

BOOMS, STICKS, AND LINKAGES

L 347-4900 LIFT, STANDARD 2V ....................................0 NC

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

5 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

BOOMS, STICKS, AND LINKAGES (CONT.)

Please pay attention to compatibility, it is dependent on Lift

L 367-5610 LUBRICATION, STANDARD ............................... 0 NC

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

6 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

BOOMS, STICKS, AND LINKAGES (CONT.)

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

7 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

L 347-4973 NO RIDE CONTROL ..................................... 0 NC

L 478-3882 RIDE CONTROL...................................... 252 $9,980

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

8 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

L 540-2511 CAB, BASIC .......................................... 0 $3,170

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

9 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

OPERATOR ENVIRONMENT (CONT.)

INTEGRATED OBJECT DETECTION SYSTEM

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

10 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

OPERATOR ENVIRONMENT (CONT.)

Authorization varies by country, please reference

L 509-4155 PRODUCT LINK, CELLULAR PLE641 ......................... 0 NC

Supersedes 02JAN2018 Subject to change without notice Effective 02JAN2019

11 Bid Term: 2/20/19 - 2/19/21

CATERPILLAR MACHINE PRICE LIST

FUEL SYSTEMS (CONT.)

L 433-3843 FUEL LINES, HEATED ...................................16 $1,030