Hfe Denon Dra-F107 F107dab Service en

Ver.
5
Please refer to the
MODIFICATION NOTICE.
SERVICE MANUAL
MODEL JP E3 E2 EK E2A E1C E1K EUT
DRA-F107 3
DRA-F107DAB 3
AM-FM STEREO RECEIVER
●
For purposes of improvement, specifications and design are subject to change without notice.
●
Please use this service manual with referring to the operating instructions without fail.
● Some illustrations using in this service manual are slightly different from the actual set.
e
D&M Holdings lnc.
S0089-1V05DM/DG1007
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK

Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.
CAUTION Please heed the points listed below during servicing and inspection.
◎ Heed the cautions! ◎ Inspect for safety after servicing!

Spots requiring particular attention when servicing, such Check that all screws, parts and wires removed or discon-
as the cabinet, parts, chassis, etc., have cautions indicated nected for servicing have been put back in their original po-
on labels or seals. Be sure to heed these cautions and the sitions, inspect that no parts around the area that has been
cautions indicated in the handling instructions. serviced have been negatively affected, conduct an insu-
lation check on the external metal connectors and between
◎ Caution concerning electric shock! the blades of the power plug, and otherwise check that
safety is ensured.
(1) An AC voltage is impressed on this set, so touching in-
ternal metal parts when the set is energized could
(Insulation check procedure)
cause electric shock. Take care to avoid electric shock,
Unplug the power cord from the power outlet, disconnect
by for example using an isolating transformer and
the antenna, plugs, etc., and turn the power switch on. Us-
gloves when servicing while the set is energized, un-
ing a 500V insulation resistance tester, check that the in-
plugging the power cord when replacing parts, etc.
sulation resistance between the terminals of the power
(2)There are high voltage parts inside. Handle with extra plug and the externally exposed metal parts (antenna ter-
care when the set is energized. minal, headphones terminal, microphone terminal, input
terminal, etc.) is 1MΩ or greater. If it is less, the set must
◎ Caution concerning disassembly and be inspected and repaired.
assembly!
Though great care is taken when manufacturing parts from
sheet metal, there may in some rare cases be burrs on the
CAUTION Concerning important safety
edges of parts which could cause injury if fingers are
moved across them. Use gloves to protect your hands.
parts
◎ Only use designated parts! Many of the electric and structural parts used in the set
have special safety properties. In most cases these prop-
The set's parts have specific safety properties (fire resis- erties are difficult to distinguish by sight, and using re-
tance, voltage resistance, etc.). For replacement parts, be placement parts with higher ratings (rated power and
sure to use parts which have the same properties. In par- withstand voltage) does not necessarily guarantee that
ticular, for the important safety parts that are marked z on safety performance will be preserved. Parts with safety
wiring diagrams and parts lists, be sure to use the desig- properties are indicated as shown below on the wiring dia-
nated parts. grams and parts lists is this service manual. Be sure to re-
place them with parts with the designated part number.
◎ Be sure to mount parts and arrange
the wires as they were originally! (1) Schematic diagrams ... Indicated by the z mark.
For safety reasons, some parts use tape, tubes or other in- (2) Parts lists ... Indicated by the z mark.
sulating materials, and some parts are mounted away from
Using parts other than the designated
the surface of printed circuit boards. Care is also taken with
parts could result in electric shock, fires or
the positions of the wires inside and clamps are used to
other dangerous situations.
keep wires away from heating and high voltage parts, so
be sure to set everything back as it was originally.
2
DRA-F107 / DRA-F107DAB
DIMENSION
3
WIRE ARRANGEMENT
If wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as
they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.
Wire arrangement viewed from the top
Front Panel side
Back Panel side
4
DISASSEMBLY
• Disassemble in order of the arrow of the figure of following flow.
• In the case of the re-assembling, assemble it in order of the reverse of the following flow.
TOP COVER
FRONT PANEL ASSY AMP PCB REAR PANEL

Refer to "EXPLODED VIEW" Refer to "EXPLODED VIEW" Refer to "EXPLODED VIEW"
FRONT PCB AMP PCB REAR PANEL
(Ref. No. of EXPLODED VIEW : C2) (Ref. No. of EXPLODED VIEW : C7) (Ref. No. of EXPLODED VIEW : M14)
SMPS PCB MAIN PCB

Refer to "EXPLODED VIEW" UPDATE PCB Refer to "EXPLODED VIEW"
SMPS PCB Refer to "EXPLODED VIEW" MAIN PCB
(Ref. No. of EXPLODED VIEW : C3) UPDATE PCB (Ref. No. of EXPLODED VIEW : C8)
(Ref. No. of EXPLODED VIEW : C13)
POWER PCB
Refer to "EXPLODED VIEW"
TUNER PACK POWER PCB
Refer to "EXPLODED VIEW" (Ref. No. of EXPLODED VIEW : C6)
TUNER PACK
(Ref. No. of EXPLODED VIEW : C12) PHONO PCB
PHONO PCB
(Ref. No. of EXPLODED VIEW : C11)
DAB PCB
DAB PCB
(Ref. No. of EXPLODED VIEW : C9
Please refer to "EXPLODED VIEW" for the disassembly method of each PCB.
5
CAUTION IN SERVICING
Initializing DRA-F107/DRA-F107DAB
DRA-F107/DRA-F107DAB initialization should be performed when the μcom, and peripheral parts of μcom are replaced.
1. Switch off the unit and remove the AC cord from the wall outlet.
2. Hold the following the 0 button and the AUTO PRESET button, and plug the AC cord into the outlet. d
Note:・All user settings will be lost and this factory setting will be recovered when this initialization mode.
So make sure to m+emorize your setting for restoring after the initialization.
6
SPECIAL MODECD TEST MODE
No Button name Function Display
S1.1
・Plug AC cord into power outlet while pressing
the ON/STANDBY button and the SDB/ D R A V E R
Version No.
S1 TONE button same time on Main Unit.
Display Mode ・The Version number of MPU is displayed.
・MUTING ON ***** : The version number of Main MPU
・Unplug AC cord to clear this mode.
S1.2
※ When the iPod Dock is connected
・Plug AC cord into power outlet while pressing D R A V E R
Version No. the ON/STANDBY button and the SDB/ D O C K V E R + + + +
S1
Display Mode TONE button same time on Main Unit.
・The Version number of MPU is displayed. ***** : The version number of MPU
・MUTING ON ++++ : The version number of iPod Dock
・Plug AC cord into power outlet while pressing ・All segment turn on and off.
the ON/STANDBY button and the AUTO
PRESET button same time on Main Unit.
VFD checking
S2 ・All segment of FLD is turning on and off every
mode
one second .
・MUTING ON.
the ON/STANDBY button and the TUNER
button same time on Main Unit.
・ON / STANDBY LED lighted ORANGE (The
test is started).
EEPROM
S3 ・MUTING ON.
testing Mode
・When power LED lighted Green, this
EEPROM test was OK.
・When power LED lighted RED, this EEPROM
test was NG.
the AUTO PRESET button and the 0 button
same time on Main Unit.
・The system is reset.
- source : CD/USB
- SDB : OFF
- BASS :0
- TREBLE :0
- BALANCE : CENTER
- DIMMER : 100%
Cold start mode - VOLUME :0
S4 - Preset Frequency of TUNER:
(Initialization)
All 0
- Main Unit 0/1 button:
-/+ button for PRESET
- CLOCK : 00:00(Flashing)
: AM12:00(Flashing)(E3)
- TIMER(EVERYDAY/ONCE):
Timer Function : CD
Timer start time : 0:00 (AM12:00 : E3)
Timer stop time : 0:00 (AM12:00 : E3)
・The system is reset, and once this is com-
pleted the unit is set to the normal mode.
7
TROUBLE SHOOTING
1. FLD dosen't light
Check Fuse Check if there is any leak or short-circuiting
SMPS B'D N.G on rectifier circuit of SMPS B'D
䊶 F901 OK? Check Parts
䊶 Q903,IC93,IC92,DB91 on SMPS B'D
O.K.
Check Power Supply Voltages for System uCOM.

MAIN B'D MCU,Function Bloc䌫 N.G Check Soldering.
䊶 [BN96]:1pin ST+6V 䊶 [BN96]:1䌰䌩䌮
䊶 [D607]:Cathode 䊶 SUB TRANS B'D
䊶 [IC65]:3pin +3.3V
O.K.
Check Reset signal for System uCOM.

䊶 [IC62]:10pin RESET 䊶 IC66 on MAIN B'D
"H"level O.K.? (>2.8V)
O.K.
Check Oscillation waveform.

䊶 [IC62]:11pin 䊶 X202 on Main B'D
14.7456MHz OK?
O.K.
Check Power 50/60 Signal

䊶 [IC62]:19pin 50/60 䊶 [BN96]: 2pin
Pulse OK? 䊶 SUB TRANS B'D
O.K.
Check Power Supply Voltages for FLD Check Soldering.

FRONT B'D 䊶 FRONT B'D [BN83]:3pin +VKK
䊶 [FL81]:38pin VH (42V) 䊶 FRONT B'D [BN83]:4pin ,5pin F_AC
䊶 [FL81]:37pin VDD (3.3V) 䊶 FRONT B'D [WF81]:1pin SW+3.3V
䊶 [FL81]: 1pin F1,43pin F2 (AC3.3V) N.G 䊶 SMPS B'DCN93 3pin VKK
䊶 SMPS B'D,CN93 4pin FL+- 5pin FL-
䊶 MAIN B'DWN81 1pin SW+3.3V
Check Parts
䊶 SMPS B'D
Q933,Q934, IC97,D945, D935
IC94, D950 ,D933
O.K.
Check Reset Signal for FLD Check Soldering.

FRONT B'D N.G 䊶 FRONT B'D [WF81]:5pin VFD_RST1
䊶 [FL81]:35pin /RST 䊶 MAIN B'D [WN81]:5pin VFD_RST1
Hlevel O.K.? (3.3V) 䊶 [IC62]:2pin FL_RST on MAIN B'D
O.K.
Check FLD Dirive Signal for FLD Check Soldering.

FRONT B'D N.G 䊶 [WF81]: 2,3,4pin on FRONT B'D
䊶 [FL81]:32,33,34pin DA,CP,CS VFD_DI,VFD_CLK,VFD_CE
䊶 [WN81]: 2,3,4pin on MAIN B'D
VFD_DI,VFD_CLK,VFD_CE
䊶 IC62 on MAIN B'D
END
8
2. POWER OFF with Blinking POWER LED
Check Power Supply Voltages for Analog Block Check Soldering.
MAIN B'D MCU,Function Bloc䌫 N.G 䊶 IC22,23 on MAIN B'D
䊶䈀IC21䈁:31pin AVCC+7V 䊶䈀BN61䈁:1pin,2pin ±12V on MAIN B'D
67pin AVCC-7V 䊶䈀CN92䈁1pin,2pin ±12V on SMPS B'D
䊶 SMPS B'D IC97,IC98,D945,D931
O.K.
Check Power Supply Voltages for Digital Block Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G MAIN B'D MCU,Function Bloc䌫
䊶䈀IC64䈁:3pin 䋫3.3V 䊶 IC64
䊶䈀WC52䈁:3pin HB+ 䊶䈀BN61䈁:4pin SW5.6V
䊶䈀WC52䈁:3pin 27VA
D.POWER AMP B'D
䈀WP52䈁:3pin 27VA
䈀CN91䈁:1,2,3,7pin 27VA
SMPS B'D
䈀BN91䈁:1,2,3,7pin 27VA
D931
O.K.
Check Protect Signal for System uCOM. Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G MAIN B'D MCU,Function Bloc䌫
䊶 [IC62]:71pin PROT_2 High Level OK? 䊶 D371,D373,D374
O.K.
Check Protect Signal for D.Power Amp Check Soldering.

D.POWER AMP B'D N.G D.POWER AMP B'D
䊶䈀IC53䈁:3pin 12V 䊶 IC54
䊶䈀IC54䈁:17pin SD,18pin OTW,19 pin READY 䊶 IC53
High Level OK? ㇱຠ⏕⹺
䊶 IC54,IC53
䊶 D.Power Amp Heat Sink
O.K.
Check Control Singal for DC Protect Check Soldering.

䊶 Q573_B Low Level OK? MAIN B'D MCU
䊶 Q571,572,573,574
䊶 D571,572
N.G Check Parts
䊶 Q571,572,573,574
䊶 D571,572
O.K.
Check Protect Signal for System uCOM. Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G MAIN B'D MCU
䊶 [IC62]:74pin PROT_1 High Level OK? 䊶 D570
D.POWER AMP B'D
䊶 D504,D505,D506
END
9
3. System Connector(DENON BUS) don't work
Check Power Supply Voltages for DENON BUS Check Soldering.
INPUT B'D DENON BUS BLOCK N.G INPUT B'D DENON BUS BLOCK
䊶 [WF31䈁:13pin ST5V 䊶 [WF31䈁:13pin ST5V
MAIN B'D
䊶 [WN31䈁:13pin ST5V
䊶 Q613
䊶䈀BN96䈁:1pin ST6V
䊶 D607
䊶 SUB TRANS B'D
O.K.
Check Control Signal for DENON BUS Check Soldering.

INPUT B'D DENON BUS BLOCK N.G INPUT B'D DENON BUS BLOCK
䊶 [WF31䈁:9pin BUS CLK,10pin BUS RXD_O 䊶 JK31
11pin BUS TXD_O OK? 䊶 Q301,Q302
䊶 [WF31] 9,10,11pin
MAIN B'D
[WN31] 9,10,11pin
IC31
[IC21]:26,27,28 pin
O.K.
END
4. The Key Operation don't work

Check Signal for KEY Check Soldering.
MAIN B'D N.G 䊶 WF81,S801䌾S809,VR81,VR82 on FRONT B'D
䊶 [IC62]3,5pin F_JOG±,21,22 VJOG± 䊶 WN81,IC62 in MAIN B'D
䇭17pin PWR_KEY,93,95pin Key 0/1 OK?
O.K.
END
5. The Remote Control Operation don't work
Check Signal for Remote Control Check Soldering.

䊶䌛IC62䌝:73pin REMOTE on MAIN B'D N.G 䊶 WF81on FRONT B'D
䊶䌛RC81䌝:3pin Vcc 3.3V OK? 䊶 WN81,IC62 in MAIN B'D
O.K.
END
10
6. No Sound,Noise generated
(1)CD/USB PLAY in
Check Analog Audio Data input for FUNCTION IC
䊶 [IC21] input 78,79pin 䊶 [IC21] on MAIN B'D
CD_L,CD_R 䊶 JK21
O.K.
Check Power Supply Voltages for PREAMP & POWER AMP. Check Soldering.
MAIN B'D MCU,Function Block N.G 䊶 [BN61]:1,2pin +12V,-12V,
䊶 [BN61]:1,2,4pin+12V,-12V , SW+5.6V 4pin SW+5.6V on MAIN B'D
䃨 D.POWER AMP B'D 䊶 [CN91]:1,2,3,7pin +27Von D.AMP BLOCK
䊶 [WP51]:5pin +12V 䊶䈀WP51䈁:5pin +12V
䊶 [CN91] : 1,2,3,7pin +27V 䊶 SMPS B'D IC97,IC98,D945,D931
䊶 [IC53]: 3pin +12V 䊶 SMPS B'D IC91,D951
䊶 D.POWER AMP B'D IC53
O.K.
Check Power Supply Voltages for FUNCTION IC Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G 䊶 IC22,IC23 on MAIN B'D
䊶 [IC21]:30pin VDD (3.3V) 䊶 IC64 on MAIN B'D
31pin AVCC+7V,67pin AVCC-7V
O.K.
Check Control Signal for FUNCTION IC Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G 䊶 IC62 on MAIN B'D
䊶 [IC21]:27,28,29pin
CLK,DATA,LATCH
O.K.
Check Analog Audio Data output from FUNCTION & Check Soldering.
PRE AMP N.G 䊶 IC21 on MAIN B'D
MAIN B'D MCU,Function Bloc䌫䊶 IC24 on MAIN B'D
䊶 [IC21]:44, 39pin Lout,Rout
䊶 [IC24]:1,7 pin
O.K.
Check Audio function Mute Signal. Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G 䊶 Q603,604, on MAIN B'D
[Q103,104]:"L"level O.K.? (-12V) 䊶 IC62 on MAIN B'D
O.K.
Check Analog Audio Data input for POWER AMP Check Soldering.
D.AMP B'D N.G 䊶 [WC51] 1,3pin on MAIN B'D,
䊶 [IC54]: 6,7pin IN_A,IN_B VOL_L_OUT,VOL_R_OUT
12,13pin IN_C, IN_D 䊶䈀WP51䈁:1,3pin on D.Power B'D
䊶 IC51,IC52 on D.AMP B'D
O.K.
Check SPEAKER RELAY control Signal Check Soldering.

MAIN B'D N.G 䊶 Q570,Q575 on MAIN B'D
䊶 [D573]:ANODE "L"level O.K.? (-12V) 䊶 [IC62] 77pin RL_MUTE on MAIN B'D
O.K.
11
Check Analog Audio Data output for POWER AMP Check Soldering.
to SPEAKER. 䊶 WP52 on D.AMP BLOCK
D.POWER AMP BLOCK N.G 䊶 IC54 on D.AMP BLOCK
䊶 [IC54]:39,40pin OUT_A , 36pin OUT_B 䊶 WC52 on MAIN B'D
31pin OUT_C , 27,28pin OUT_D
MAIN B'D SP OUT BLOCK
䊶 JK51
O.K.
END
(2) AM/FM TUNER-in
Check Power Supply Voltages for AM/FM TUNER. Check Soldering.

MAIN B'D N.G 䊶 D931 on SMPS B'D
䊶 Q813, 611 on MAIN B'D
䊶䈀IC62䈁:59pin TU_PWR
O.K.
Check Control Signal for AM/FM TUNER. Check Soldering.
MAIN B'D N.G MAIN B'D
䊶 [WN21]: 7pin PLL_CE,8pin R/F_DATA 䊶 IC61,62,WN21
9pin RF_CLK,10pinPLL_DI OK?
O.K.
Check Analog Audio Data output from TUNER PACK Check Soldering.
MAIN B'D N.G 䊶 WN21 1,3 pin TU_L,TU_R on MAIN B'D
䊶 TUNER PACK output
䊶 [WN 21]:1,3pin TU_L, TU_R
䊶 [IC21]:68,69pin䇭TU_L,TU_R
O.K.
to CD/USB in 䃨Mark
(3) Portable-in(Front-in)
Check Analog Audio Data output from Prtable-in

FRONT B'D N.G Check Soldering.
䊶 Portable-in output 䊶 JK82,on FRONT B'D
䊶 BN82 1,3pin POR_L.POR_R 䊶 BN82 on FRONT B'D
O.K.
Check Analog Audio Data input for FUNCTION IC Check Soldering.

MAIN B'D MCU,Function Bloc䌫 N.G 䊶 [CN82]:1,3pin PORT_L<PORT_R on MAIN B'D
䊶 [IC21] input 2,3pin 䊶 [WP11]:10,12pin on MAIN B'D
POR_L.POR_R 䊶 [WC11]:10,12pin on MAIN B'D
䊶 [IC21]:2,3pin PORT_L,PORT_R
O.K.
12
(4) DAB TUNER-in
Check Power Supply Voltages for DAB TUNER UNIT. Check Soldering.
INPUT B'D DAB BLOCK N.G 䊶䈀WP82䈁:1pin DAB_PWR
䊶䈀WP82䈁:5pin 5VDD 5pin SW+5V on INPUT B'D
䊶䈀CN71䈁:2pin 3.3V 䊶 IC71,72 on INPUT B'D
䊶䈀CN71䈁:1pin 1.5V 䊶䈀WC61䈁:1pin DAB_PWR
5pin 5VDD on MAIN B'D
䊶䈀BN61䈁:5pin 5VDD on MAIN B'D
䊶 D931 on POWER B'D
䊶䈀IC62䈁:53pin DAB_PWR
Check Parts
䊶 IC71,72 on INPUT B'D
O.K.
Check Controll Signal for DAB TUNER. Check Soldering.

INPUT B'D DAB BLOCK N.G 䊶 WP82 33,34pin on DAB B'D
䊶 CN71 15,16pin DIN,DOUT 䊶 IC62
O.K.
Check Analogl Audio Data output from DAB TUNER

INPUT B'D DAB BLOCK N.G Check Soldering.
䊶 [DAB TUNER] output 䊶 [CN71]:29,30pin on DAB B'D
[CN71]: 29,30pin LOUT,ROUT
O.K.
Check Analog Audio Data input for FUNCTION IC

MAIN B'D N.G Check Soldering.
䊶 [IC21]:72,73pin DAB_L,BAD_R 䊶䈀WP82䈁:6pin,8pin on INPUT B'D
䈀WC61䈁:6pin,8pin on MAIN B'D
O.K.
(5) iPod PLAY
Check Control Signal for iPod Dock Check Soldering.

MAIN B'D N.G INPUT B'D
䊶 JK32 䊶 JK32
㩷䈀WF31䈁:4,12pin IPOD_TX,IPOD_RX 䊶 [WF31]: 4,12pin IPOD_TX,IPOD_RX
㪤㪘㪠㪥㩷㪙㩾㪛
䊶 [WN31]: 4,12pin IPOD_TX,IPOD_RX
䊶 [ IC62]:29,30pin
䊶 IC61
O.K.
Check Analog signal output from iPod Dock Check Soldering.

MAIN B'D N.G 䊶 JK21 on MAIN B'D
䊶 JK21 AUXi in L,R
䊶 [IC21]:71,71pin AUX1_L,AUX1_R
O.K.
13
(6) PHONO PLAY
Check Power Supply Voltages for PHONO Check Soldering.

INPUT B'D PHONO BLOCK N.G 䊶䈀WP11䈁:4pin-7V,5pin +7V
䊶䈀WP11䈁:4pin-7V,5pin +7V 䊶䈀WC11䈁:4pin-7V,5pin +7V on Main B'D
O.K.
Check Soldering.
Check Analog signal input for FUNCTION IC 䊶 [IC21]:80,1pin PHONO_L,PHONO_R
MAIN B'D N.G 䊶䈀㪮㪚㪈㪈䈁㪑㪈㪃㪊㫇㫀㫅
䊶 [IC21]:49,50pin LOUT,ROUT 䊶䈀㪮㪧㪈㪈䈁㪑㪈㪃㪊㫇㫀㫅
䊶 IC11
䊶 JK11
O.K.
(7) Head Phone OUT
Check Analog signal output forom FUNCTION IC Check Soldering.

MAIN B'D N.G MAIN B'D
䊶 [IC21]:54pin LOUT,47pin ROUT 䊶 [IC21]:54pin LOUT,47pin ROUT
㪫㪦㩷㩿㪈㪀㪚㪛ౣ↢
O.K.
Check Power Supply Voltages for Head Phone Amp Check Soldering.
INPUT B'D H/P AMP BLOCK N.G 䊶䈀㪮㪧㪈㪈䈁㪑㪋㫇㫀㫅㩷㪄㪎㪭㪃㩷㪌㫇㫀㫅㩷㪂㪎㪭㩷㫆㫅㩷㪠㪥㪧㪬㪫㩷㪙㩾㪛
䊶䈀㪮㪧㪈㪈䈁㪑㪋㫇㫀㫅㩷㪄㪎㪭㪃㩷㪌㫇㫀㫅㩷㪂㪎㪭䊶䈀㪮㪚㪈㪈䈁㪑㪋㫇㫀㫅㩷㪄㪎㪭㪃㩷㪌㫇㫀㫅㩷㪂㪎㪭㩷㫆㫅㩷㪤㪘㪠㪥㩷㪙㩾㪛
O.K.
Check Soldering.
Check Mute Control signal for Head Phone INPUT B'D H/P BLOCK
INPUT B'D H/P BLOCK N.G 䊶䈀WP11䈁:13pin HP_MUTE
䊶䈀WP11䈁:13pin HP_MUTE Low Level OK?(-7V) MAIN B'D
䈀WC11䈁:13pin HP_MUTE
O.K.
Check Soldering.
Check Analog signal output from Head Phone Amp 䊶䈀㪮㪚㪈㪈䈁㪎㫇㫀㫅㩷㪟㪧㪶㪣㪠㪥㪃㪏㫇㫀㫅㩷㪟㪧㪶㪩㪠㪥㩷㫆㫅㩷㪤㪘㪠㪥㩷㪙㩾㪛
INPUT B'D H/P BLOCK N.G INPUT B'D H/P BLOCK
䊶 [IC13]:1pin LOUT,7pin ROUT 䊶䈀㪮㪧㪈㪈䈁㪎㫇㫀㫅㩷㪟㪧㪶㪣㪠㪥㪃㪏㫇㫀㫅㩷㪟㪧㪶㪩㪠㪥㩷㫆㫅㩷㪤㪘㪠㪥㩷㪙㩾㪛
㪝㫉㫆㫅㫋㩷㪙㩾㪛䊶 IC13
䊶䈀㪙㪥㪏㪉䈁㪑㪌㫇㫀㫅㩷㪟㪧㪶㪣㪦㪃㪍㫇㫀㫅㩷㪟㪧㪶㪩㪦䊶䈀㪚㪥㪏㪉䈁㪑㪌㫇㫀㫅㩷㪟㪧㪶㪣㪦㪃㪍㫇㫀㫅㩷㪟㪧㪶㪩㪦
㪝㫉㫆㫅㫋㩷㪙㩾㪛
䊶䈀㪙㪥㪏㪉䈁㪑㪌㫇㫀㫅㩷㪟㪧㪶㪣㪦㪃㪍㫇㫀㫅㩷㪟㪧㪶㪩㪦
㪚㪿㪼㪺㫂㩷㪧㪸㫉㫋㫊
Q105,Q106,Q107,Q108
O.K.
END
14
MEASURING POINT AND WAVEFORMS
MEASURING POINT
FRONT PCB
Detail A
q w e
UPDATE PCB
W1
t
W2
y 㩷
15
MAIN PCB
Q3, Q4
㪛
㪙
㪛㪼㫋㪸㫀㫃㩷㪚
Q0
Q1
㪛㪼㫋㪸㫀㫃㩷㪛
Q7
㪛㪼㫋㪸㫀㫃㩷㪙
Q5
Q6
u Q8
16
POWER AMP
Q2
Q1
DAB PCB
Q9
W0
17
WAVEFORMS
FLD Drive Signal DENON BUS
䊶Mode:Fanction Select 䊶Mode:Push Remote Control "CD Play"
qFL_DA
rBUS_CLK
wFL_CP
tBUS_RXD
eFL_CS
yBUS_TXD
Remote Control
䊶Mode:Push Remote Control "SOURCE"
uREMOTE
CD/USB INPUT
䊶Mode:Fanction Select
iCLK
oDATA
Q0LATCH
CD/USB Play
䊶Mode: CD INPUT=200mVrms,1kHz Speaker=4ohm 䊶Mode: CD INPUT=Open䇮Speaker=4ohm
Q1OUTA Q1OUTA
Q2OUTB Q2OUTB
18
䊶Mode: CD INPUT=200mVrms,1kHz Speaker=4ohm 䊶Mode: CD INPUT=Open䇮Speaker=4ohm
Q1OUTA Q1OUTA
Q3SPEAKER Q3SPEAKER
OUT FL+ OUT FL+
Q4SPEAKER Q4SPEAKER
OUT FL- OUT FL-
AM/FM TUNER INPUT

䊶Mode:Function CD㸢Tuner FM 䊶Mode:Tuner Band FM㸢AM
Q5PLL_CE Q5PLL_CE
Q6R/F_DATA Q6R/F_DATA
Q7R/F_CLK Q7R/F_CLK
Q8PLL_DI Q8PLL_DI
DAB TUNER INPUT iPod Play

䊶Mode:Tuner Band AM㸢DAB 䊶Mode:iPod Connect
W1IPOD_TX
Q9DIN
W2IPOD_RX
W0DOUT
19
SEMICONDUCTORS
Only major semiconductors are shown, general semiconductors etc. are omitted to list.
The semiconductor which described a detailed drawing in a schematic diagram are omitted to list.
1. IC’s
M3062LFGPGP (IC62)
75 51
76 50
100 26
1 25
M3062LFGPGP Terminal Function
Output of
Pin Port Port
Port Name Explaanation Standby &
No. Function setting
Default
1 P94 O [LED_RL] [STANDBY Red LED output. ON:High] L
2 P93 O FL RESET Reset output to FLD L
3 TB2IN I FUNC_JOGB FUNCTION encoder Pulse-B input HI-Z
4 P91 O Not Used:N.C. L
5 TB0IN I FUNC_JOGA FUNCTION encoder Pulse-A input HI-Z
6 BYTE (VSS) GND -
7 CNVSS I FLASH CNVss Select input of Flash rom write mode HI-Z
10 RESET I RESET Reset input HI-Z
11 XOUT XTAL(16MHz) Xtal output -
12 VSS (VSS) GND -
13 XIN XTAL(16MHz) Xtal input -
14 VCC (VCC) Positive power -
15 NMI I (PullUp) Pull up HI-Z
17 INT1 INT POWER KEY Power button input (interrupt input) HI-Z
18 INT0 INT /DBRXD DENON BUS Data input (interrupt input) HI-Z
19 P81 I 50/60 50Hz/60Hz AC Input HI-Z
20 P80 I H/P SW HEAD PHONE insert detect signal input HI-Z
21 TA3IN I VOL JOGB VOL encoder Pulse-B input HI-Z
22 TA3OUT I VOL JOGA VOL encoder Pulse-A input HI-Z
23 P75 O FLCS Chip Select output to FLD L
24 P74 O LED G POWER/SANDBY Green LED output. ON:High L
25 P73 O LED R POWER/SANDBY Red LED output. ON:High L
26 CLK2 O /DBCLK(DENON BUS) Serial Clock output for DENON BUS H
27 RXD2 I /DBRXD(DENON BUS) Serial Data input for DENON BUS HI-Z
20
Output of
Pin Port Port
Default
28 TXD2 O /DBTXD(DENON BUS) Serial Data output for DENON BUS H
29 TXD3 SO IPOD_TX Serial Data output for IPOD DOCK L
30 RXD3 SI IPOD_RX Serial Data input for IPOD DOCK HI-Z
31 CLK1 I (PULLDOWN) Pull down L
33 P63 SO S1_DIN Serial Data output to DAB Module L
34 P62 SI SI_DOUT Serial Data input from DAB Module L
37 P57 O.D Not Used:N.C. L
39 P55 I (FLASH EPM) Not Used:N.C. HI-Z
40 P54 SO E2P CLK Serial Clock output to EEPROM L
41 P53 SI E2P DO Serial Data input from EEPROM HI-Z
42 P52 SO E2P DI Serial Data output to EEPROM L
43 P51 O E2P CS Chip Enable output to EEPROM L
44 P50 O (FLASH CE) Not Used:N.C. H
46 P46 I PWB check Pull down HI-Z
53 P37 O /FMAM TUNER Select to DAB or AM/FM . DAB:High AM/FM:Low L
54 P36 O TU/PHO REC.OUTPUT level Select to TU/PHO or Others . TU/PHO:High L
57 P33 O SW MUTE MUTE output for SW OUTPUT H
59 P31 O TP.ON/OFF (TPOWER) AM/FM TUNER Power ON/OFF Switching output L
60 (VCC) Positive power -
62 (VSS) GND -
64 P26 I STEREO "STEREO" indicator input from FM/AM TUNER pack HI-Z
65 P25 I TUNED "TUNED" detect input from FM/AM TUNER pack HI-Z
66 P24 O T.MUTE MUTE output for FM/AM TUNER pack L
67 P23 O SANYO CE Chip Enable output to PLL/RDS IC L
68 P22 O SANYO DI Serial Data input to PLL/RDS IC L
69 P21 O SANYO CLK Serial Clock output to PLL/RDS IC L
70 P20 I SANYO DO Serial Data output to PLL/RDS IC HI-Z
71 P17 I PROTECT2 Protect Signal input 2 HI-Z
72 P16 O /SYR Reset output to RDS IC L
73 INT3 INT REMOTE Remote Control signal input HI-Z
74 P14 I PROTECT1/SP Protect Signal input 1 HI-Z
PROTECTION
75 P13 O /BUF_EN Enable signal output fot BUS BUFFER IC H
76 P12 O VR MUTE MUTE output for POWER AMP H
77 P11 O RL(RMUTE) SPEAKER RELAY ON/OFF output L
78 P10 O AP.ON/OFF (APOWER) ± 15V POWER ON/OFF Switching output ON:Hight L
79 P07 O H/P MUTE MUTE output for HEAD PHONE output L
80 P06 O P.ON/OFF (POWER) MAIN POWER ON/STANDBY Switching output ON:High L
21
Output of
Pin Port Port
Default
82 P04 O [RECOUT MUTE] [MUTE output for REC.OUTPUT] L
83 P03 O M61531_DATA Serial Data output to M61531 L
84 P02 O M61531_CLK Serial Clock output to M61531 L
85 P01 O M61531_LATCH Latch output to M61531 L
86 P00 I PORT.IN_SW PORTABL INPUT insert detect signal input HI-Z
87 P107 I Pull up HI-Z
88 P106 I USA Initial Setting input HI-Z
89 P105 I EURO Initial Setting input HI-Z
90 P104 I Pull up L
91 AN3 AD FREQ Initial Setting input HI-Z
92 AN2 AD RDS Initial Setting input HI-Z
93 AN1 AD KEY 0 Unit Operation Button input 0 HI-Z
94 (VSS) GND -
95 AN0 AD KEY 1 Unit Operation Button input 1 HI-Z
96 VREF (VCC) Positive power -
97 AVCC (VCC) Positive power -
99 P97 SO FLDA Serial Data output to FLD L
100 P95 SO FLCK Serial Clock output to FLD L
22
M61531FP (IC21)
Block Diagram and Pin Configuration (Top View)
33 SWSELOUT
39 SLSELOUT
38 CSELOUT
35 SWOUT
27 CLOCK
34 SWVIN
29 LATCH
25 SWIN2
26 DGND
40 SLVIN
36 COUT
30 DVDD
31 AVCC
28 DATA
37 CVIN
32 GND
Cch SWch
GND
SLch
SLOUT 41 Output
Gain
Output
Gain
AVCC DVDD 24 CIN2
Control Control
SROUT 42 SRch LA TCH
23 SLIN2
Cch SWch
VOL VOL
MCU I/F DATA
SRVIN 43 CLK 22 SRIN2
Input
Gain Multi
SRSELOUT 44 Control Input Selector 21 RIN2
SLch VOL SWch
Output
RSELOUT 45 Gain Input 20 LIN2
Control Gain
Control Cch
RVIN 46 Multi
Input Selector
GND 19 GND
Input
Rch
Rch Output -1 LOUD R
ROUT 47 Gain Gain
Control SLch 18 /BALANCE R/−
Control Loud
R2 /Balance
SRch VOL Multi
TRE R 48 Input
Input Selector
Loudness tap
17 BALANCE R/+
Loudness tap
Gain
Rch VOL R2
BASS R2 49 Output
Control
SRch
GND 16 GND
Gain Lch
Bypass/Tone Input Multi -1 LOUD L
BASS R1 50 Control Gain
Control
Input Selector
15 /BALANCE L/−
Loud
L/R VOL L2 /Balance
R1
BASS L1 51 Input
14 BALANCE L/+
Tone(Bass,Treble)
Tone Loudness tap

Rch
Tone Block Position Input

ATT R3 Rch
BASS L2 52 Tone Block Position GND 13 GND
L/R VOL
L3
Lch
Input
TRE L 53
L1
Tone
Lch
12 RIN1
Input
Lch ATT
Input
LOUT 54 Output
Bypass/Tone Gain
Bypass/Tone 11 LIN1
Gain Control
L1
Control
LVIN 55 Lch VOL L3 10 SLIN1
L2
Loudness tap Input ATT
LSELOUT 56 9 SRIN1
Lch
GND 57 GND 8 SWIN1
R3 R1
RECL1 58 Bypass/Tone
7 CIN1
Input ATT
RECR1 59 GND 6 GND
Rch
RECL2 60 5 INR1/EXT INR
Bypass
RECR2 61 Selector
4 INL1/EXT INL
Lch Rch
RECL3 62 3 INR2
RECR3 63 2 INL2
GND 64 AVEE
1 INR3
GND
INL10/RECL4 65
INR10/RECR4 66
AVEE 67
INL9 68
INR9 69
INL8 70
INR8 71
INL7 72
INR7 73
INL6 74
INR6 75
INL5 76
INR5 77
INL4 78
INR4 79
INL3 80
23
Pin Description
Pin No. Pin Name Function
3, 1, 79, 77, 75, 73, 71, 69 INR2, 3, 4, 5, 6, 7, 8, 9 Input pin of R channel (Input Selector)
2, 80, 78, 76, 74, 72, 70, 68 INL2, 3, 4, 5, 6, 7, 8, 9 Input pin of L channel (Input Selector)
4 INL1/EXT INL Input pin of L channel (Input Selector)/External Input pin(Lch)
5 INR1/EXT INR Input pin of L channel (Input Selector)/External Input pin(Rch)
6, 13, 16, 19, 32, 57, 64 GND Analog Ground
7, 24 CIN1/CIN2 Input pin of C channel (2 Input Selector)
8, 25 SWIN1/SWIN2 Input pin of SW channel (2 Input Selector)
9, 22 SRIN1/SRIN2 Input pin of SR channel (2 Input Selector)
10, 23 SLIN1/SLIN2 Input pin of SL channel (2 Input Selector)
11, 20 LIN1/LIN2 Input pin of L channel (2 Input Selector)
12, 21 RIN1/RIN2 Input pin of R channel (2 Input Selector)
14, 17 BALANCE L/+, R/+ Output pin of L/R channel Balance Output(+)
15, 18 LOUD L/BALANCE L/–, Frequency characteristic setting pin of Loudness
LOUD R/BALANCE R/– /Output pin of L/R channel Balance Output(–)
26 DGND Ground of internal logic circuit
27, 28, 29 CLOCK, DATA, LATCH Input pin of control clock /data/ trigger
30 DVDD Power supply to internal logic circuit
31 AVCC Positive power supply to internal analog circuit
33 SWSELOUT Output pin of SW channel volume input selector
34 SWVIN Input pin of SW channel volume
35 SWOUT Output pin of SW channel
36 COUT Output pin of C channel
37 CVIN Input pin of C channel volume
38 CSELOUT Output pin of C channel volume input selector
39 SLSELOUT Output pin of SL channel volume input selector
40 SLVIN Input pin of SL channel volume
41 SLOUT Output pin of SL channel
42 SROUT Output pin of SR channel
43 SRVIN Input pin of SR channel volume
44 SRSELOUT Output pin of SR channel volume input selector
45 RSELOUT Output pin of R channel volume input selector
46 RVIN Input pin of R channel volume
47 ROUT Output pin of R channel
51, 52, 50, 49 BASS L1, L2/BASS R1, R2 Frequency characteristic setting pin of tone control (BASS)
53, 48 TRE L/TRE R Frequency characteristic setting pin of tone control (TREBLE)
54 LOUT Output pin of L channel
55 LVIN Input pin of L channel volume
56 LSELOUT Output pin of L channel volume input selector
58, 60, 62/59, 61, 63 REC L1, L2, L3 Output pin of REC (Lch and Rch)
/REC R1, R2, R3
65 INL10/REC L4 Input pin of L channel (Input Selector)/Output pin of REC (Lch)
66 INR10/REC R4 Input pin of R channel (Input Selector)/Output pin of REC (Rch)
67 AVEE Negative power supply to internal analog circuit
24
TAS5630DKD (IC54)
PSU_REF
GVDD_B
GVDD_A
PVDD_A
PVDD_A
GND_A
OUT_A
OUT_A
BST_A
GND
GND
VDD
NC
NC
NC
NC
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
OC_ADJ 1 48 GND_A
/RESET 2 47 GND_B
C_STARTUP 3 46 GND_B
INPUT_A 4 45 OUT_B
INPUT_B 5 44 OUT_B
VI_CM 6 43 PVDD_B
GND 7 42 PVDD_B
AGND 8 41 BST_B
VREG 9 40 BST_C
INPUT_C 10 39 PVDD_C
INPUT_D 11 38 PVDD_C
FREQ_ADJ 12 37 OUT_C
OSC_IO+ 13 36 OUT_C
OSC_IO- 14 35 GND_C
/SD 15 64-pins QFP package 34 GND_C
/OTW1 16 33 GND_D
26
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
READY
/OTW2
/CLIP
M1
M2
M3
GND
GND
GVDD_C
GVDD_D
OUT_D
BST_D
OUT_D
PVDD_D
PVDD_D
GND_D
TAS5630DKD Block Diagram
25
TAS5630DKD Terminal Function
TERMINAL
FUNCTION(1) DESCRIPTION
NAME PHD NO. DKD NO.
AGND 8 10 P Analog ground
BST_A 54 43 P HS bootstrap supply (BST), external 0.033 uF capacitor to OUT_A required.
BST_B 41 34 P HS bootstrap supply (BST), external 0.033 uF capacitor to OUT_B required.
BST_C 40 33 P HS bootstrap supply (BST), external 0.033 uF capacitor to OUT_C required.
BST_D 27 24 P HS bootstrap supply (BST), external 0.033 uF capacitor to OUT_D required.
/CLIP 18 - O Clipping warning; open drain; active low
C_STARTUP 3 5 O Startup ramp requires a charging capacitor of 4.7 nF to AGND in BTL mode.
FREQ_ADJ 12 14 I PWM frame rate programming pin requires resistor to AGND
GND 7, 23, 24, 57, 58 9 P Ground
GND_A 48, 49 38 P Power ground for half-bridge A
GND_B 46, 47 37 P Power ground for half-bridge B
GND_C 34, 35 30 P Power ground for half-bridge C
GND_D 32, 33 29 P Power ground for half-bridge D
GVDD_A 55 - P Gate drive voltage supply requires 0.1 uF capacitor to GND_A
GVDD_B 56 - P Gate drive voltage supply requires 0.1 uF capacitor to GND_B
GVDD_C 25 - P Gate drive voltage supply requires 0.1 uF capacitor to GND_C
GVDD_D 26 - P Gate drive voltage supply requires 0.1 uF capacitor to GND_D
GVDD_AB - 44 P Gate drive voltage supply requires 0.22 uF capacitor to GND_A/GND_B
GVDD_CD - 23 P Gate drive voltage supply requires 0.22 uF capacitor to GND_C/GND_D
INPUT_A 4 6 I Input signal for half bridge A
INPUT_B 5 7 I Input signal for half bridge B
INPUT_C 10 12 I Input signal for half bridge C
INPUT_D 11 13 I Input signal for half bridge D
M1 20 20 I Mode selection
NC 59-62 - - No connect, pins may be grounded.
OC_ADJ 1 3 O Analog over current programming pin requires resistor to ground.
OSC_IO+ 13 15 I/O Oscillaotor master/slave output/input.
OSC_IO- 14 16 I/O Oscillaotor master/slave output/input.
/OTW - 18 O Overtemperature warning signal, open drain, active low.
/OTW1 16 - O Overtemperature warning signal, open drain, active low.
/OTW2 17 - O Overtemperature warning signal, open drain, active low.
OUT_A 52, 53 39, 40 O Output, half bridge A
OUT_B 44, 45 36 O Output, half bridge B
OUT_C 36, 37 31 O Output, half bridge C
OUT_D 28, 29 27, 28 O Output, half bridge D
PSU_REF 63 1 P PSU Reference requires close decoupling of 330 pF to AGND
Power supply input for half bridges A requires close decoupling of 2.2-uF capacitor
PVDD_A 50, 51 41, 42 P
to GND_A
Power supply input for half bridges B requires close decoupling of 2.2-uF capacitor
PVDD_B 42, 43 35 P
to GND_B
Power supply input for half bridges C requires close decoupling of 2.2-uF capacitor
PVDD_C 38, 39 32 P
to GND_C
Power supply input for half bridges D requires close decoupling of 2.2-uF capacitor
PVDD_D 30, 31 25, 26 P
to GND_D
READY 19 19 O Normal operation; open drain; active high
/RESET 2 4 I Device reset Input; active low, requires 47kOhm pull up resistor to VREG.
/SD 15 17 O Shutdown signal, open drain, active low
Power supply for internal voltage regulator requires a 10-uF capacitor in parallel
VDD 64 2 P
with a 0.1-uF capacitor to GND for decoupling.
Analog comparator reference node requires close decoupling of
VI_CM 6 8 O
1 nF to AGND
VREG 9 11 P Internal regulator supply filter pin requires 0.1-uF capacitor to AGND
(1) I = input, O = output, P = power
26
ICE2QS01 (IC93)
ZC 1 8 GND Pin Symbol Function
1 ZC Zero Crossing
REG 2 7 VCC 2 REG Regulation
3 CS Primary Current Sensing
CS 3 6 OUT 4, 5 HV High Voltage input

6 OUT gate driver out put
7 VCC IC supply voltage
HV 4 5 HV
8 GND Common ground
Blockdigram
VZCT2
ringing
suppression
VZCT1 time control
ZC
1
PWM generator
Zero-crossing
VOLP OLP counter
up/down
VVCCOVP VCC
auto counter
OVP
restart
VCC active burst
REG UVP control
2
RReg Vvccuvp
VOPOVP output
VREF OVP
latch on/off FF
VcsSW off
SWP
gate driver
current limitation /
CS foldback correction OUT
3 6
Vcsth
power management
current measurement
HV power cell
4, 5 v1 GND
8
controller
Vos
VCC
7
27
ICE2QS01 Functional description
Functional Description
3 Functional Description drops (Phase II). Once the output voltage is high
enough, the VCC capacitor receives then energy from
the auxiliary winding from the time point t2 on. The VCC
3.1 VCC Pre-Charging and Typical then will reach a constant value depending on output
load.
VCC Voltage During Start-up Since there is a VCC undervoltage protection, the
In the controller ICE2QS01, a power cell is integrated. capacitance of the VCC capacitor should be selected to
As shown in Figure 2, the power cell consists of a high be high enough to ensure that enough energy is stored
voltage device and a controller, whereby the high in the VCC capacitor so that the VCC voltage will never
voltage device is controlled by the controller. The touch the VCC under voltage protection threshold
power cell provides a pre-charging of the VCC VVCCUVP before the output voltage is built up. Therefore,
capacitor till VCC voltage reaches the VCC turned-on the capacitance should fulfill the following requirement:
threshold VVCCon and the IC begins to operate, while it
I VCCop t 2 – t 1
may keep the VCC voltage at a constant value during C vcc t -----------------------------------------------
- [2]
burst mode operation when the output voltage is pulled V VCCon – V VCCUVP
down or the power from the auxiliary winding is not
with IVCCop the operating current of the controller.
enough, or when the IC is latched off in certain
protection mode.
Once the mains input voltage is applied, a rectified 3.2 Soft-start
voltage shows across the capacitor Cbus. The high
voltage device provides a current to charge the VCC At the time t1, the IC begins to operate with a soft-start.
capacitor Cvcc. Before the VCC voltage reaches a By this soft-start the switching stresses for the switch,
certain value, the amplitude of the current through the diode and transformer are minimised. The soft-start
high voltage device is only determined by its channel implemented in the ICE2QS01 is a digital time-based
resistance and can be as high as several mA. After the function. The preset soft-start time is 24ms with 8
VCC voltage is high enough, the controller controls the steps. The internal reference for the regulation voltage
high voltage device so that a constant current around begins at 1.35V and with an increment of 0.35V for
1mA is provided to charge the VCC capacitor further, each following step.
until the VCC voltage exceeds the turned-on threshold
VVCCon. As shown as the time phase I in Figure 3, the 3.3 Normal Operation
VCC voltage increase near linearly.
The PWM section of the IC can be divided into two
main portions: PWM controller for normal operation
VCC and PWM controller for burst mode operation. The
VVCCon i ii iii PWM controller for normal operation will be described
in the following paragraphs, while the PWM controller
VVCCUVP for burst mode operation will be discussed in the next
section.
The PWM controller for normal operation consists of
digital signal processing circuit including an up/down
t1 t2 t counter, a zero-crossing counter (ZC-counter) and a
comparator, and analog circuit including a current
measurement unit and a comparator. The switch-on
Figure 3 VCC voltage at start up and -off time point is determined by the digital circuit
The time taking for the VCC pre-charging can then be and the analog circuit, respectively. As input
approximately calculated as: information for the switch-on determination, the zero-
crossing input signal and the value of the up/down
V VCCon C vcc counter are needed, while the feedback signal vREG
t 1 = ---------------------------------
- [1]
I VCCch arg e2 and the current sensing signal vCS are necessary for
the switch-off determination. Details about the
where IVCCcharge2 is the charging current from the power operation of the PWM controller in normal operation
cell which is 1.05mA, typically. are illustrated in the following paragraphs.
Exceeds the VCC voltage the turned-on threshold
VVCCon of at time t1, the power cell is switched off, and 3.3.1 Switch-on Determination
the IC begins to operate with a soft-start. Due to power As mentioned above, the digital signal processing
consumption of the IC and the fact that still no energy circuit consists of an up/down counter, a zero-crossing
from the auxiliary winding to charge the VCC capacitor counter and a comparator. A ringing suppression time
before the output voltage is built up, the VCC voltage
28
controller is implemented to avoid mistriggering by the limited between 1 and 7. If the counter tends to count
ring after MOSFET is turned off. Functionality of these beyond this range, the attempt is ignored.
parts is described as in the following. In normal case, the up/down counter can only be
changed by one each time at the clock period of 48ms.
3.3.1.1 Up/down Counter However, to ensure a fast response to sudden load
The up/down counter stores the number of zero increase, the counter is set to 1 in the following
crossing to be ignored before the main power switch is switching period after the regulation voltage vREG
switched on after demagnetisation of the transformer. exceeds the threshold VRM.
This value is a function of the regulation voltage, which
contains information about the output power. 3.3.1.2 Zero-Crossing Counter and Ringing
Generally, a high output power results in a high Suppression Time Controller
regulation voltage. According to this information, the In the system, the voltage from the auxiliary winding is
value in the up/down counter is changed to a low value applied to the zero-crossing pin through a RC network,
in case of high regulation voltage, and to a high value which provides a time delay to the voltage from the
in case of low regulation voltage. In ICE2QS01, the auxiliary winding. Internally, this pin is connected to a
lowest value of the counter is 1 and the highest 7. clamping network, a zero-crossing detector, an output
Following text explains how the up/down counter value overvoltage (OP OVP) detector and a ringing
changes in responding to the regulation voltage vREG. suppression time controller.
The regulation voltage vREG is internally compared with
During on-state of the power switch a negative voltage
three thresholds VRL, VRH and VRM. According to the
applies to the ZC pin. Through the internal clamping
results, the value in the up/down counter is changed,
network, the voltage at the pin is clamped to certain
which is summarised in Table 1 and Figure 4
level. However, it is highly recommended that a fast-
respectively.
recovery diode Dzc is added to block the negative
Table 1 Operation of the up/down counter voltage when the power switch is on. This is because
up/down counter the device in MOS technology is sensitive to negative
vREG
action voltage.
Count upwards till The voltage at the ZC pin vZC is compared with the
Always lower than VRL
7 threshold VZCT1. Once the voltage vZC crosses the
Once higher than VRL, but Stop counting, no threshold at its falling edge, a pulse is generated which
always lower than VRH value changing is fed to the zero-crossing counter and the counter
Once higher than VRH, but Count downwards value increases by 1.
always lower than VRM till 1 After MOSFET is turned on, there will be some
Set up/down oscillation on VDS, which will also appear on the voltage
Once higher than VRM
counter to 1 on ZC pin. To avoid the MOSFET is turned on
mistriggerred by such oscillation, a ringing suppression
timer is implemented. The time is dependent on the
clock T=48ms voltage vZC. When the voltage vZC is lower than the
threshold VZCT2, a longer preset time applies, while a
shorter time is set when the voltage vZC is higher than
the threshold.
t
V FB The voltage vZC is used for the output overvoltage
V RM protection, as well. Once the voltage at this pin is
higher than the threshold VOPOVP during off-time of the
V RH
main switch, the IC is latched off after a fixed blanking
V RL time.
To achieve the switch-on at voltage valley, the voltage
t
from the auxiliary winding is fed to a time delay network
n+1
n+2
n+2
n+2
n+2
n+1
n-1
1 (the RC network consists of Dzc, Rzc1, Rzc2 and Czc as

n
Case 1 4 5 6 6 6 6 5 4 3 1 shown in typical application circuit) before it is applied

to the zero-crossing detector through the ZC pin. The
Case 2 2 3 4 4 4 4 3 2 1 1
needed time delay to the main oscillation signal 't
Case 3 7 7 7 7 7 7 6 5 4 1 should be approximately one fourth of the oscillation
period (by transformer primary inductor and drain-
Figure 4 Up/down counter operation source capacitor) minus the propagation delay from the
According to the comparison results the up/down
counter counts upwards, keeps unchanged or counts
downwards. However, the value in up/down counter is
29
detected zero-crossing to the switch-on of the main 3.3.2 Switch-off Determination

switch tdelay, theoretically: In the converter system, the primary current is sensed
by an external shunt resistor, which is connected
T osc
't = ---------
- – t delay [3] between low-side terminal of the main power switch
4 and the common ground. The sensed voltage across
This time delay should be matched by adjusting the the shunt resistor vCS is applied to an internal current
time constant of the RC network which is calculated as: measurement unit, and its output voltage v1 is
compared with the regulation voltage vreg. Once the
R zc1 R zc2 voltage v1 exceeds the voltage vREG, the output flip-flop
W td = C zc ---------------------------
- [4] is reset. As a result, the main power switch is switched
R zc1 + R zc2
off. The relationship between the v1 and the vcs is
described by:
3.3.1.3 Switch-on Determination
In the system, turn-on of the power switch depends on v 1 = 3.3 v CS + 0.7 [5]
the value of the up/down counter, the value of the zero-
crossing counter and the voltage at the ZC pin vZC. To avoid mistriggering caused by the voltage spike
Turn-on happens only when the value in the both across the shunt resistor after switch-on of the main
counters are the same and the voltage at the ZC is power switch, a 330ns leading edge blanking time
lower than the threshold VZCT1. For comparison of the applies to output of the comparator.
values from both counters, a digital comparator is used.
Once these counters have the same value, the 3.3.3 Foldback Point Correction
comparator generates a signal which sets the on/off In addition to the cycle-by-cylce primary current
flip-flop, only when the voltage vZC is lower than the limitation, the IC incorporats a foldback point
threshold VZCT1. correction. The current limit on CS pin voltage is now a
Another signal which may trigger the digital comparator time dependent one. If the mains input voltage is high,
is the output of a TsMax clock signal, which limits the the MOSFET on time will be short and the current limit
maximum off time to avoid the low-frequency will be low. In such a way, the maximum output power
operation. for the SMPS designed with ICE2QS01 will be nearly
constant against the variations of mains input voltage.
During active burst mode operation, the digital
The current sense voltage limit versus the MOSFET
comparator is disabled and no pulse will be generated.
maximum on time is shown in Figure 5.
0 .8
0 .6
Vcs-max(V)
0 .4
0 .2
0
0 5 10 15 20 25 30
Ton(us )
Figure 5 Maximum current limit versus MOSFET maximum on time
30
3.4 Active Burst Mode Operation exceed VLB (4.5V). After leaving active busrt mode,
maximum current can now be provided to stabilize VO.
At very low load condition, the IC enters active burst In addition, the up/down counter will be set to 1
mode operation to minimize the input power. Details immediately after leaving active burst mode. This is
about active burst mode operation are explained in the helpful to decrease the output voltage undershoot.
following paragraphs.
3.4.4 IC Power Supply During Active Burst
3.4.1 Entering Active Burst Mode Operation Mode
For determination of entering active burst mode During active burst mode operation, the power cell is
operation, three conditions apply: activated again. Once the power from the auxiliary
the regulation voltage is lower than the threshold of winding is not high enough to keep the VCC voltage
VEB(1.1V). Accordingly, the peak voltage across the above the preset value of VVCCBL, the power cell keeps
shunt resistor is 0.11V; the VCC voltage at the preset value VVCCBL. Otherwise,
the up/down counter has its maximal value of 7; and if the VCC voltage is still above this value, no current
flows through the power cell though it is activated.
a certain blanking time (24ms).
Once all of these conditions are fulfilled, the active VREG Entering Leaving
burst mode flip-flop is set and the controller enters Active Burst Active Burst
burst mode operation. This multi-conditional Mode Mode
determination for entering active burst mode operation 4.4V
3.6V
prevents mistriggering of entering active burst mode
3.0V
operation, so that the controller enters active burst
mode operation only when the output power is really 1.1V
low during the preset blanking time.
Blanking Window (24ms) t
3.4.2 During Active Burst Mode Operation VCS
After entering the Active Burst Mode the regulation
voltage rises as VOUT starts to decrease due to the
inactive PWM section. One comparator observes the Current limit level
1.0V
regulation signal if the voltage level VBH (3.6V) is during Active Burst
exceeded. In that case the internal circuit is again Mode
activated by the internal bias to start with swtiching. 0.25V
Turn-on of the power MOSFET is triggered by the
timer. The PWM generator for burst mode operation VVCC t
composes of a timer with a fixed frequency of 80kHz,
typically, and an analog comparator. Turn-off is
resulted by comparison of the voltage signal v1 with an
internal threshold, by which the voltage across the
shunt resistor VcsB is 0.25V, accordingly. A turn-off can
also be triggered by the maximal duty ratio controller 12.5V
which sets the maximal duty ratio to 50%. In operation,
the output flip-flop will be reset by one of these signals VO t
which come first. Max. Ripple < 1%
If the output load is still low, the regulation signal
decreases as the PWM section is operating. When
regulation signal reaches the low threshold VBL(3.0V),
the internal bias is reset again and the PWM section is
disabled until next time regultaion siganl increases
beyond the VBH threshold. If working in active burst
mode the regulation signal is changing like a saw tooth t
between 3.0V and 3.6V shown in Figure 6.
Figure 6 Signals in active burst mode
3.4.3 Leaving Active Burst Mode
The regulation voltage immediately increases if there is
a high load jump. This is observed by one comparator.
As the current limit is 25% during active burst mode a
certain load is needed so that regulation voltage can
31
3.5 Protection Functions

The IC provides full protection functions. The following
table summarizes these protection functions.
Table 2 Protection features
VCC Overvoltage Auto Restart Mode

VCC Undervoltage Auto Restart Mode
Overload/Open Loop Auto Restart Mode
Output Overvoltage Latched Off Mode
Short Winding Latched Off Mode
During operation, the VCC voltage is continuously
monitored. In case of an under- or an over-voltage, the
IC is reset and the main power switch is then kept off.
After the VCC voltage falls below the threshold
VVCCUVP, the power cell is activated. The VCC capacitor
is then charged up. Once the voltage exceeds the
threshold VVCCon, the IC begins to operate with a new
soft-start.
In case of open control loop or output over load, the
regulation voltage will be pulled up . After a blanking
time of 24ms, the IC enters auto-restart mode. The
blanking time here enables the converter to provide a
high power in case the increase in VREG is due to a
sudden load increase. During off-time of the power
switch, the voltage at the zero-crossing pin is
monitored for output over-voltage detection. If the
voltage is higher than the preset threshold vOPOVP, the
IC is latched off after the preset blanking time.
If the voltage at the current sensing pin is higher than
the preset threshold vcsSW during on-time of the power
switch, the IC is latched off. This is short-winding
protection.
During latch-off protection mode, the power cell is
activated and it keeps the VCC voltage at the level of
VVCCBL.
32
Electrical Characteristics
4 Electrical Characteristics
Note: All voltages are measured with respect to ground (Pin 8). The voltage levels are valid if other ratings are
not violated.
4.1 Absolute Maximum Ratings

Note: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction
of the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 7
(VCC) is discharged before assembling the application circuit.
Parameter Symbol Limit Values Unit Remarks

min. max.
HV Voltage VHV - 500 V
VCC Supply Voltage VVCC -0.3 27 V
REG Voltage VREG -0.3 5.0 V
ZC Voltage VZC -0.3 5.0 V
CS Voltage VCS -0.3 5.0 V
OUT Voltage VOUT -0.3 27 V
Junction Temperature Tj -40 125 qC
Storage Temperature TS -55 150 qC
Thermal Resistance RthJA - 90 K/W PG-DIP-8
Junction-Ambient
ESD Capability VESD - 2 kV Human body model1)
1)
According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5k: series resistor)
4.2 Operating Range

Note: Within the operating range the IC operates as described in the functional description.

min. max.
VCC Supply Voltage VVCC VVCCUVP VVCCOVP V
Junction Temperature TjCon -25 125 °C
33
4.3 Characteristics
4.3.1 Supply Section

Note: The electrical characteristics involve the spread of values guaranteed within the specified supply voltage
and junction temperature range TJ from – 25 oC to 125oC. Typical values represent the median values,
which are related to 25°C. If not otherwise stated, a supply voltage of VCC = 18 V is assumed.
Parameter Symbol Limit Values Unit Test Condition

min. typ. max.
Start-Up Current IVCCstart - 300 550 PA VVCC = 21V
VCC Charge Current IVCCcharge1 5.0 mA VVCC = 0V
IVCCcharge2 0.55 1.05 1.60 mA VVCC = 1V
IVCCcharge3 - 0.88 - mA VVCC = 21V
Leakage Current of IStartLeak - 0.2 50 PA VHV= 610V
Power Cell at Tj = 100°C
Supply Current in normal IVCCop - 2.5 3.6 mA Output low
operation
Supply Current in IVCCrestart - 300 - PA
Auto Restart Mode
with Inactive Gate
Supply Current in IVCClatch - 300 - PA
Latch-off Mode
Supply Current in Burst Mode IVCCburst - 500 950 PA VREG = 2.5V
with Inactive Gate
Supply Voltage with no power VVCCBL - 12.5 - V VHV = 100V
from auxiliary winding in burst
mode or in latch-off mode
VCC Turn-On Threshold VVCCon 21.2 22.0 22.8 V
Internal Reference Voltage VREF 4.8 5.0 5.2 V measured at pin REG,
IREG = 0
34
4.3.2 PWM Section

min. typ. max.
Regulation Pull-Up Resistor RREG 14 23 33 k:
PWM-OP Gain AV 3.18 3.3 - -
Offset for Voltage Ramp VOS 0.63 0.7 - V
Soft-Start time tSOFTS 18 21 38 ms
Zero crossing threshold voltage VZCT1 20 50 110 mV
Ringing suppression threshold VZCT2 0.7 V
Minimum ringing suppression tZCRST1 2.2 4.2 5.5 Ps VZC > VZCT2
time
Maximum ringing suppression tZCRST2 - 42 - Ps VZC < VZCT2
time
Threshold to set Up/Down VRM 3.9 V
Counter to one
Threshold for downward VRH 3.2 V
counting
Threshold for upward counting VRL 2.5 V
1)
Counter time tCOUNT 48 ms
Maximum restart time in normal tsMax 33 42 60 Ps VZC<VZCT1
operation
Leading Edge Blanking tLEB 200 330 460 ns
Peak current limitation in normal Vcsth 0.95 1.0 1.05 V
operation
Regulation voltage for entering VEB 1.1 V
Burst Mode
Regulation voltage for leaving VLB 4.5 V
Burst Mode
Regulation voltage for burst-on VBH 3.6 V
Regulation voltage for burst-off VBL 3.0 V
Fixed Switching Frequency in fsB 64 80 96 kHz
Burst Mode
Max. Duty Cycle in Burst Mode DmaxB 0.5
Peak Current Limitation in Burst VcsB 0.22 0.25 0.3 V
Mode
1) The parameter is not subject to production test - verified by design/characterization
35
4.3.3 Protection

min. typ. max.
VCC overvoltage threshold VVCCOVP 24 25.0 26 V
VCC undervoltage threshold VVCCUVP 10.3 11.0 11.7 V
Over Load or Open Loop VOLP 4.5 V
Detection threshold for OLP
protection at REG pin
Over Load or Open Loop TOLP-B 16 24 35 ms
Protection Blanking Time
Output Overvoltage detection VOPOVP 4.5 V
threshold at the ZC pin
Threshold for short winding VcsSW 1.68 V
protection
Note: The trend of all the voltage levels in the Control Unit is the same regarding the deviation except VVCCOVP
4.3.4 Gate Driver

min. typ. max.
Output voltage at logic low VGATElow 0.7 V IOUT = 20mA
Output voltage at logic high VGATEhigh 10.0 V IOUT = -20mA
Output voltage active shut down VGATEasd 1.0 V VVCC = 7V
V IOUT = 20mA
Rise Time trise - 100 - ns COUT = 4.7nF
Fall Time tfall - 25 - ns COUT = 4.7nF
36
Blockdiagram
FB
Isense
Drain
SoftS
+
ICE2B265 (IC92)
Converter
Snubber DC Output
RStart-up CLine
85 ... 270 VAC
4
3
2
VOUT
1
CVCC
VCC Drain
Power Management
Undervoltage
5
6
7
8
Lockout Internal Bias

13.5V
C1
8.5V
16.5V Duty Cycle Max
Power-Down 6.5V 0.72
Reset 5.3V Oscillator
N.C
VCC
GND
Voltage
Drain
4.8V Duty Cycle

6.5V 4.0V Reference max
C2 Power-Up 4.0V
G1
Reset Clock
RSoft-Start
fstandby-fnorm
SoftS Soft Start Soft-Start
Comparator PWM-Latch CoolMOS™
S Q
1)
8
7
5
4
3
2
1
5.6V
CSoft-Start
37
Pin
Spike R Q
C4 S Q
5.3V G3 Blanking Gate
G2 5 s G4
T1 6.5V Driver
R Q
FB
4.8V PWM
N.C
C3 Comparator
VCC
GND
Error-Latch
Drain
Drain
SoftS
RFB
Isense
0.3V
at Tj = 110°C
Symbol
C5
Current-Limit RSense
FB fosc 10k
Thermal Shutdown Comparator Leading Edge
Blanking
fnorm Vcsth
Tj >140°C fstandby 220ns D1 Isense
0.8V
UFB
2)
Propagation-Delay
Function
Protection Unit Standby Unit

Soft-Start
Compensation
Feedback
x3.65
PWM OP
Current Limiting
Not connected
Improved Current Mode

Optocoupler
Controller Ground
at Tj = 25°C
CoolSET™-F2
GND
Controller Supply Voltage
CoolMOS™ Source Output
Controller Current Sense Input,
650V1)/800V2) CoolMOS™ Drain

650V1)/800V2) CoolMOS™ Drain
ICE2Axxxx ICE2Bxxxx
f norm 100kHz 67kHz
f standby 21.5kHz 20kHz

3 Functional Description 3.2 Improved Current Mode
3.1 Power Management Soft-Start Comparator
Main Line (100V-380V)

PWM-Latch
RStart-Up FB
R Q
Primary Winding Driver
CVCC PWM Comparator
S Q
VCC
Power Management 0.8V

Undervoltage
Internal
Lockout
Bias
PWM OP
13.5V
8.5V
x3.65 Isense
Power-Down 6.5V
Reset 5.3V Improved
Voltage
Reference
4.8V Current Mode
4.0V
Power-Up
Reset
Figure 7 Current Mode
R Q Current Mode means that the duty cycle is controlled
PWM-Latch by the slope of the primary current. This is done by
6.5V comparison the FB signal with the amplified current
S Q
RSoft-Start sense signal.
SoftS Error-Latch
Soft-Start Comparator
Amplified Current Signal

CSoft-Start T1 Error-Detection
FB
Figure 6 Power Management

0.8V
The Undervoltage Lockout monitors the external
supply voltage VVCC. In case the IC is inactive the
current consumption is max. 55μA. When the SMPS is Driver t
plugged to the main line the current through RStart-up
charges the external Capacitor CVCC. When VVCC
exceeds the on-threshold VCCon=13.5V the internal bias
circuit and the voltage reference are switched on. After
that the internal bandgap generates a reference T on
voltage VREF=6.5V to supply the internal circuits. To
avoid uncontrolled ringing at switch-on a hysteresis is
implemented which means that switch-off is only after t
active mode when Vcc falls below 8.5V.
In case of switch-on a Power Up Reset is done by Figure 8 Pulse Width Modulation
resetting the internal error-latch in the protection unit.
When VVCC falls below the off-threshold VCCoff=8.5V the In case the amplified current sense signal exceeds the
internal reference is switched off and the Power Down FB signal the on-time Ton of the driver is finished by
reset let T1 discharging the soft-start capacitor CSoft-Start resetting the PWM-Latch (see Figure 8).
at pin SoftS. Thus it is ensured that at every switch-on The primary current is sensed by the external series
the voltage ramp at pin SoftS starts at zero. resistor RSense inserted in the source of the integrated
CoolMOS™. By means of Current Mode regulation, the
38
secondary output voltage is insensitive on line
variations. Line variation changes the current
waveform slope which controls the duty cycle. VOSC
The external RSense allows an individual adjustment of
the maximum source current of the integrated max.
CoolMOS™. Duty Cycle
Soft-Start Comparator
PWM Comparator t
Voltage Ramp
FB
PWM-Latch 0.8V
FB
Oscillator 0.3V 0.3V
C5
VOSC Gate Driver t
Gate Driver
0.8V
10k:
x3.65
T2 R1
V1
PWM OP
C1 20pF t
Figure 10 Light Load Conditions

Voltage Ramp
3.2.1 PWM-OP
Figure 9 Improved Current Mode
The input of the PWM-OP is applied over the internal
To improve the Current Mode during light load leading edge blanking to the external sense resistor
conditions the amplified current ramp of the PWM-OP RSense connected to pin Isense. RSense converts the
is superimposed on a voltage ramp, which is built by source current into a sense voltage. The sense voltage
the switch T2, the voltage source V1 and the 1st order is amplified with a gain of 3.65 by PWM OP. The output
low pass filter composed of R1 and C1(see Figure 9, of the PWM-OP is connected to the voltage source V1.
Figure 10). Every time the oscillator shuts down for The voltage ramp with the superimposed amplified
max. duty cycle limitation the switch T2 is closed by current signal is fed into the positive inputs of the PWM-
VOSC. When the oscillator triggers the Gate Driver T2 is Comparator, C5 and the Soft-Start-Comparator.
opened so that the voltage ramp can start.
In case of light load the amplified current ramp is to
small to ensure a stable regulation. In that case the 3.2.2 PWM-Comparator
Voltage Ramp is a well defined signal for the The PWM-Comparator compares the sensed current
comparison with the FB-signal. The duty cycle is then signal of the integrated CoolMOSTM with the feedback
controlled by the slope of the Voltage Ramp. signal VFB (see Figure 11). VFB is created by an
By means of the Comparator C5, the Gate Driver is external optocoupler or external transistor in
switched-off until the voltage ramp exceeds 0.3V. It combination with the internal pull-up resistor RFB and
allows the duty cycle to be reduced continuously till 0% provides the load information of the feedback circuitry.
by decreasing VFB below that threshold. When the amplified current signal of the integrated
CoolMOS™ exceeds the signal VFB the PWM-
Comparator switches off the Gate Driver.
39
pull-up resistor RSoft-Start. The Soft-Start-Comparator
compares the voltage at pin SoftS at the negative input
6.5V with the ramp signal of the PWM-OP at the positive
input. When Soft-Start voltage VSoftS is less than
RFB Soft-Start Comparator Feedback voltage VFB the Soft-Start-Comparator limits
the pulse width by resetting the PWM-Latch (see
Figure 12). In addition to Start-Up, Soft-Start is also
FB activated at each restart attempt during Auto Restart.
PWM-Latch
By means of the above mentioned CSoft-Start the Soft-
Start can be defined by the user. The Soft-Start is
finished when VSoftS exceeds 5.3V. At that time the
PWM Comparator Protection Unit is activated by Comparator C4 and
senses the FB by Comparator C3 wether the voltage is
below 4.8V which means that the voltage on the
0.8V secondary side of the SMPS is settled. The internal
Zener Diode at SoftS has a clamp voltage of 5.6V to
Optocoupler prevent the internal circuit from saturation (see Figure
PWM OP
13).
Isense
x3.65
6.5V
Power-Up Reset
5.6V
Improved RSoft-Start Error-Latch
Current Mode R Q
SoftS
6.5V C4
Figure 11 PWM Controlling 5.3V G2 S Q
3.3 Soft-Start 4.8V R Q

RFB C3
Gate
Driver
VSoftS FB Clock S Q
PWM-Latch
5.6V
5.3V Figure 13 Activation of Protection Unit
The Start-Up time TStart-Up within the converter output
voltage VOUT is settled must be shorter than the Soft-
TSoft-Start Start Phase TSoft-Start (see Figure 14).
T Soft – Start
Gate Driver t C Soft – Start = ------------------------------------
-
R Soft – Start u 1.69
By means of Soft-Start there is an effective

minimization of current and voltage stresses on the
integrated CoolMOS™, the clamp circuit and the output
overshoot and prevents saturation of the transformer
during Start-Up.
t
Figure 12 Soft-Start Phase
The Soft-Start is realized by the internal pull-up resistor
RSoft-Start and the external Capacitor CSoft-Start (see
Figure 5). The Soft-Start voltage VSoftS is generated by
charging the external capacitor CSoft-Start by the internal
40
VSoftS kHz
100
5.3V
65
fOSC
TSoft-Start
21.5
VFB t 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 V
ICE2Axxxx ICE2Bxxxx VFB
fnorm 100kHz 67kHz
4.8V fstandby 21.5kHz 20kHz
Figure 15 Frequency Dependence
VOUT t 3.5 Current Limiting

There is a cycle by cycle current limiting realized by the
VOUT Current-Limit Comparator to provide an overcurrent
detection. The source current of the integrated
TStart-Up CoolMOSTM is sensed via an external sense resistor
RSense. By means of RSense the source current is
transformed to a sense voltage VSense. When the
t voltage VSense exceeds the internal threshold voltage
Vcsth the Current-Limit-Comparator immediately turns
Figure 14 Start Up Phase off the gate drive. To prevent the Current Limiting from
distortions caused by leading edge spikes a Leading
3.4 Oscillator and Frequency Edge Blanking is integrated at the Current Sense.
Furthermore a Propagation Delay Compensation is
Reduction added to support the immediate shut down of the
CoolMOS™ in case of overcurrent.
3.4.1 Oscillator
The oscillator generates a frequency fswitch = 67kHz/ 3.5.1 Leading Edge Blanking
100kHz. A resistor, a capacitor and a current source
and current sink which determine the frequency are
integrated. The charging and discharging current of the VSense
implemented oscillator capacitor are internally
trimmed, in order to achieve a very accurate switching
frequency. The ratio of controlled charge to discharge Vcsth
tLEB = 220ns
current is adjusted to reach a max. duty cycle limitation
of Dmax=0.72.
3.4.2 Frequency Reduction

The frequency of the oscillator is depending on the
voltage at pin FB. The dependence is shown in Figure t
15. This feature allows a power supply to operate at
lower frequency at light loads thus lowering the Figure 16 Leading Edge Blanking
switching losses while maintaining good cross
Each time when CoolMOS™ is switched on a leading
regulation performance and low output ripple. In case
spike is generated due to the primary-side
of low power the power consumption of the whole
capacitances and secondary-side rectifier reverse
SMPS can now be reduced very effective. The minimal
recovery time. To avoid a premature termination of the
reachable frequency is limited to 20kHz/21.5 kHz to
switching pulse this spike is blanked out with a time
avoid audible noise in any case.
constant of tLEB = 220ns. During that time the output of
41
the Current-Limit Comparator cannot switch off the The propagation delay compensation is done by
gate drive. means of a dynamic threshold voltage Vcsth (see Figure
18). In case of a steeper slope the switch off of the
3.5.2 Propagation Delay Compensation driver is earlier to compensate the delay.
E.g. Ipeak = 0.5A with RSense = 2. Without propagation
In case of overcurrent detection by ILimit the shut down delay compensation the current sense threshold is set
of CoolMOS™ is delayed due to the propagation delay to a static voltage level Vcsth=1V. A current ramp of
of the circuit. This delay causes an overshoot of the dI/dt = 0.4A/μs, that means dVSense/dt = 0.8V/μs, and a
peak current Ipeak which depends on the ratio of dI/dt of propagation delay time of i.e. tPropagation Delay =180ns
the peak current (see Figure 17). leads then to a Ipeak overshoot of 14.4%. By means of
. propagation delay compensation the overshoot is only
about 2% (see Figure 19).
Signal1 Signal2
ISense tPropagation Delay
with compensation without compensation
Ipeak2 IOvershoot2
V
Ipeak1 1.3
ILimit 1.25
1.2
IOvershoot1 1.15
VSense
1.1
1.05
0.95
t
0.9
Figure 17 Current Limiting 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 V/us
dVSense
The overshoot of Signal2 is bigger than of Signal1 due
to the steeper rising waveform. dt
A propagation delay compensation is integrated to Figure 19 Overcurrent Shutdown
bound the overshoot dependent on dI/dt of the rising
primary current. That means the propagation delay
time between exceeding the current sense threshold 3.6 PWM-Latch
Vcsth and the switch off of CoolMOS™ is compensated The oscillator clock output applies a set pulse to the
over temperature within a range of at least. PWM-Latch when initiating CoolMOS™ conduction.
dI peak dV Sense After setting the PWM-Latch can be reset by the PWM-
0 d R Senseu -----------
- d --------------- OP, the Soft-Start-Comparator, the Current-Limit-
dt dt
Comparator, Comparator C3 or the Error-Latch of the
Protection Unit. In case of resetting the driver is shut
VOSC down immediately.
max. Duty Cycle
3.7 Driver
off time
The driver-stage drives the gate of the CoolMOS™ and
is optimized to minimize EMI and to provide high circuit
VSense t efficiency. This is done by reducing the switch on slope
Propagation Delay when reaching the CoolMOS™ threshold. This is
Vcsth achieved by a slope control of the rising edge at the
driver’s output (see Figure 20) to the CoolMOS™ gate.
Thus the leading switch on spike is minimized. When
CoolMOS™ is switched off, the falling shape of the
t driver is slowed down when reaching 2V to prevent an
overshoot below ground. Furthermore the driver circuit
Signal1 Signal2 is designed to eliminate cross conduction of the output
stage. At voltages below the undervoltage lockout
Figure 18 Dynamic Voltage Threshold Vcsth threshold VVCCoff the gate drive is active low.
42
Overload / Open Loop with Normal Load

VGate ca. t = 130ns
5μs Blanking
FB
4.8V
Failure
Detection
5V
t
SoftS
t 5.3V
Soft-Start Phase
Figure 20 Internal Gate Rising Slope
3.8 Protection Unit (Auto Restart Mode)

An overload, open loop and overvoltage detection is
TBurst1 t
integrated within the Protection Unit. These three Driver
failure modes are latched by an Error-Latch. Additional TRestart
thermal shutdown is latched by the Error-Latch. In case
of those failure modes the Error-Latch is set after a
blanking time of 5μs and the CoolMOS™ is shut down.
That blanking prevents the Error-Latch from distortions
caused by spikes during operation mode.
t
3.8.1 Overload / Open Loop with Normal VCC
Load 13.5V
Figure 21 shows the Auto Restart Mode in case of
overload or open loop with normal load. The detection 8.5V
of open loop or overload is provided by the Comparator
C3, C4 and the AND-gate G2 (see Figure 22). The
detection is activated by C4 when the voltage at pin
SoftS exceeds 5.3V. Till this time the IC operates in the t
Soft-Start Phase. After this phase the comparator C3 Figure 21 Auto Restart Mode
can set the Error-Latch in case of open loop or overload
which leads the feedback voltage VFB to exceed the
threshold of 4.8V. After latching VCC decreases till 6.5V
8.5V and inactivates the IC. At this time the external Power Up Reset
Soft-Start capacitor is discharged by the internal
transistor T1 due to Power Down Reset. When the IC RSoft-Start
SoftS
is inactive VVCC increases till VCCon = 13.5V by charging
the Capacitor CVCC by means of the Start-Up Resistor
RStart-Up. Then the Error-Latch is reset by Power Up
Reset and the external Soft-Start capacitor CSoft-Start is CSoft-Start
C4 Error-Latch
charged by the internal pull-up resistor RSoft-Start. During 5.3V G2
the Soft-Start Phase which ends when the voltage at T1
pin SoftS exceeds 5.3V the detection of overload and 4.8V
open loop by C3 and G2 is inactive. In this way the Start C3
Up Phase is not detected as an overload.
FB
RFB
6.5V
Figure 22 FB-Detection
43
But the Soft-Start Phase must be finished within the normal operation mode is prevented from overvoltage
Start Up Phase to force the voltage at pin FB below the detection due to varying of VCC concerning the
failure detection threshold of 4.8V. regulation of the converter output. When the voltage
VSoftS is above 4.0V the overvoltage detection by C1 is
deactivated.
3.8.2 Overvoltage due to Open Loop with
No Load
VCC
Open loop & no load condition
FB
5μs Blanking 6.5V Error Latch
C1
4.8V 16.5V G1
RSoft-Start
Failure
Detection 4.0V
SoftS C2
t
SoftS Soft-Start Phase CSoft-Start
5.3V T1 Power Up Reset
4.0V
Overvoltage
Detection Phase
Figure 24 Overvoltage Detection

TBurst2 t
Driver
TRestart 3.8.3 Thermal Shut Down
Thermal Shut Down is latched by the Error-Latch when
junction temperature Tj of the pwm controller is
exceeding an internal threshold of 140°C. In that case
the IC switches in Auto Restart Mode.
t
Overvoltage Detection
VCC
16.5V
13.5V
8.5V
Figure 23 Auto Restart Mode

Figure 23 shows the Auto Restart Mode for open loop
and no load condition. In case of this failure mode the
converter output voltage increases and also VCC. An
additional protection by the comparators C1, C2 and
the AND-gate G1 is implemented to consider this
failure mode (see Figure 24).The overvoltage detection
is provided by Comparator C1 only in the first time
during the Soft-Start Phase till the Soft-Start voltage
exceeds the threshold of the Comparator C2 at 4.0V
and the voltage at pin FB is above 4.8V. When VCC
exceeds 16.5V during the overvoltage detection phase Note: All the values which are mentioned in the
C1 can set the Error-Latch and the Burst Phase during functional description are typical. Please refer
Auto Restart Mode is finished earlier. In that case to Electrical Characteristics for min/max limit
TBurst2 is shorter than TSoft-Start. By means of C2 the values.
44
4 Electrical Characteristics
4.1 Absolute Maximum Ratings
Note: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction
of the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 6
(VCC) is discharged before assembling the application circuit.

min. max.
Drain Source Voltage VDS - 650 V Tj = 110°C
ICE2A0565/165/265/365/765I/765P2
ICE2B0565/165/265/365/765I/765P2
ICE2A0565G
ICE2A0565Z
Drain Source Voltage VDS - 800 V Tj = 25°C
ICE2A180Z/280Z/380P2
Pulsed drain current, ICE2A0565/ ID_Puls1 2.0 A
tp limited by Tjmax ICE2B056/
ICE2A0565G/
ICE2A0565Z
ICE2A165/ ID_Puls2 3.8 A
ICE2B165
ICE2B265
ICE2B365
ICE2A180Z ID_Puls5 4.1 A
ICE2A280Z ID_Puls6 14.8 A
ICE2A765P2/ ID_Puls7 19.0 A

ICE2B765P2/
ICE2A765I/
ICE2B765I
ICE2A380P2/ ID_Puls8 5.7 A
45

min. max.
Avalanche energy, ICE2A0565 EAR1 - 0.01 mJ
repetitive tAR limited by
max. Tj=150°C1) ICE2A165 EAR2 - 0.07 mJ
ICE2A265 EAR3 - 0.40 mJ
ICE2A365 EAR4 - 0.50 mJ
ICE2B0565 EAR5 - 0.01 mJ
ICE2B165 EAR6 - 0.07 mJ
ICE2B265 EAR7 - 0.40 mJ
ICE2B365 EAR8 - 0.50 mJ
ICE2A0565G EAR9 - 0.01 mJ
ICE2A0565Z EAR10 - 0.01 mJ
ICE2A180Z EAR11 - 0.07 mJ
ICE2A280Z EAR12 - 0.40 mJ
ICE2A765I EAR13 - 0.50 mJ
ICE2B765I EAR14 - 0.50 mJ
ICE2A765P2 EAR15 - 0.50 mJ
ICE2B765P2 EAR16 - 0.50 mJ
ICE2A380P2 EAR17 - 0.06 mJ
1)
Repetitive avalanche causes additional power losses that can be calculated as PAV=EAR* f
46

min. max.
Avalanche current, ICE2A0565 IAR1 - 0.5 A
repetitive tAR limited by
ICE2A165 IAR2 - 1 A
max. Tj=150°C
ICE2A265 IAR3 - 2 A
ICE2A365 IAR4 - 3 A
ICE2B0565 IAR5 - 0.5 A
ICE2B165 IAR6 - 1 A
ICE2B265 IAR7 - 2 A
ICE2B365 IAR8 - 3 A
ICE2A0565G IAR9 - 0.5 A
ICE2A0565Z IAR10 - 0.5 A
ICE2A180Z IAR11 - 1 A
ICE2A280Z IAR12 - 2 A
ICE2A765I IAR13 - 7 A
ICE2B765I IAR14 - 7 A
ICE2A765P2 IAR15 - 7 A
ICE2B765P2 IAR16 - 7 A
ICE2A380P2 IAR17 - 2.4 A
VCC Supply Voltage VCC -0.3 22 V
FB Voltage VFB -0.3 6.5 V
SoftS Voltage VSoftS -0.3 6.5 V
ISense ISense -0.3 3 V
Junction Temperature Tj -40 150 qC Controller & CoolMOS™
Storage Temperature TS -50 150 qC
Thermal Resistance RthJA1 - 90 K/W PG-DIP-8-6
Junction-Ambient
RthJA2 - 96 K/W PG-DIP-7-1
RthJA3 - 110 K/W P-DSO-16/12
1) 2)
ESD Robustness VESD - 2 kV Human Body Model
1)
Equivalent to discharging a 100pF capacitor through a 1.5 k: series resistor
2)
1kV at pin drain of ICE2x0565, ICE2A0565Z and ICE2A0565G
47
4.2 Thermal Impedance (ICE2X765I and ICE2X765P2)

min. max.
Thermal Resistance ICE2A765I RthJA4 - 74 K/W Free standing with no
Junction-Ambient ICE2B765I heat-sink
ICE2A765P2
ICE2B765P2
ICE2A380P2 RthJA5 - 82 K/W
Junction-Case ICE2A765I RthJC1 - 2.5 K/W
ICE2B765I
ICE2A765P2
ICE2B765P2
ICE2A380P2 RthJC2 - 2.86 K/W
4.3 Operating Range

Note: Within the operating range the IC operates as described in the functional description.

min. max.
VCC Supply Voltage VCC VCCoff 21 V
Junction Temperature of TJCon -25 130 qC Limited due to thermal shut down
Controller of controller
Junction Temperature of TJCoolMOS -25 150 qC
CoolMOS™
48
4.4 Characteristics
Note: The electrical characteristics involve the spread of values given within the specified supply voltage and
junction temperature range TJ from – 25 qC to 125 qC.Typical values represent the median values, which
are related to 25°C. If not otherwise stated, a supply voltage of VCC = 15 V is assumed.
4.4.1 Supply Section

min. typ. max.
Start Up Current IVCC1 - 27 55 μA VCC=VCCon -0.1V
Supply Current with Inactive IVCC2 - 5.0 6.6 mA VSoftS = 0
Gate IFB = 0
Supply Current ICE2A0565 IVCC3 - 5.3 6.7 mA VSoftS = 5V
with Active Gate IFB = 0
ICE2A165 IVCC4 - 6.5 7.8 mA
ICE2A265 IVCC5 - 6.7 8.0 mA
ICE2A365 IVCC6 - 8.5 9.8 mA
ICE2B0565 IVCC7 - 5.2 6.7 mA
ICE2B165 IVCC8 - 5.5 7.0 mA
ICE2B265 IVCC9 - 6.1 7.3 mA
ICE2B365 IVCC10 - 7.1 8.3 mA
ICE2A0565G IVCC11 - 5.3 6.7 mA
ICE2A0565Z IVCC12 - 5.3 6.7 mA
ICE2A180Z IVCC13 - 6.5 7.8 mA
ICE2A280Z IVCC14 - 7.7 9.0 mA
Supply Current ICE2A765I IVCC15 - 8.5 9.8 mA VSoftS = 5V
with Active Gate IFB = 0
ICE2B765I IVCC16 - 7.1 8.3 mA
ICE2A765P2 IVCC17 - 8.5 9.8 mA
ICE2B765P2 IVCC18 - 7.1 8.3 mA
ICE2A380P2 IVCC19 - 6.7 8.0 mA
VCC Turn-On Threshold VCCon 13 13.5 14 V
VCC Turn-Off Threshold VCCoff - 8.5 - V
VCC Turn-On/Off Hysteresis VCCHY 4.5 5 5.5 V
49
4.4.2 Internal Voltage Reference

min. typ. max.
Trimmed Reference Voltage VREF 6.37 6.50 6.63 V measured at pin FB
4.4.3 Control Section

min. typ. max.
Oscillator Frequency fOSC1 93 100 107 kHz VFB = 4V
ICE2A0565/165/265/365/765I/765P2
ICE2A0565G/0565Z/180Z/280Z/380P2
Oscillator Frequency fOSC3 62 67 72 kHz VFB = 4V
ICE2B0565/165/265/365/765I/765P2
Reduced Osc. Frequency fOSC2 - 21.5 - kHz VFB = 1V
ICE2A0565/165/265/365/765I/765P2
ICE2A0565G/0565Z/180Z/280Z/380P2
Reduced Osc. Frequency fOSC4 - 20 - kHz VFB = 1V
ICE2B0565/165/265/365/765I/765P2
Frequency Ratio fosc1/fosc2 4.5 4.65 4.9
ICE2A0565/165/265/365/765I/765P2
ICE2A0565G/0565Z/180Z/280Z/380P2
Frequency Ratio fosc3/fosc4 3.18 3.35 3.53
ICE2B0565/165/265/365/765I/765P2
Max Duty Cycle Dmax 0.67 0.72 0.77
Min Duty Cycle Dmin 0 - - VFB < 0.3V
PWM-OP Gain AV 3.45 3.65 3.85
VFB Operating Range Min Level VFBmin 0.3 - - V
VFB Operating Range Max level VFBmax - - 4.6 V
Feedback Resistance RFB 3.0 3.7 4.9 k:
Soft-Start Resistance RSoft-Start 42 50 62 k:
50
4.4.4 Protection Unit

min. typ. max.
Over Load & Open Loop VFB2 4.65 4.8 4.95 V VSoftS > 5.5V
Detection Limit
Activation Limit of Overload & VSoftS1 5.15 5.3 5.46 V VFB > 5V
Open Loop Detection
Deactivation Limit of VSoftS2 3.88 4.0 4.12 V VFB > 5V
Overvoltage Detection VCC > 17.5V
Overvoltage Detection Limit VVCC1 16 16.5 17.2 V VSoftS < 3.8V
VFB > 5V
1)
Latched Thermal Shutdown TjSD 130 140 150 °C
Spike Blanking tSpike - 5 - μs
1)
The parameter is not subject to production test - verified by design/characterization
4.4.5 Current Limiting

min. typ. max.
Peak Current Limitation Vcsth 0.95 1.0 1.05 V dVsense / dt = 0.6V/Ps
(incl. Propagation Delay Time)
Leading Edge Blanking tLEB - 220 - ns
51
4.4.6 CoolMOS™ Section

min. typ. max.
Drain Source Breakdown Voltage V(BR)DSS 600 - - V Tj=25°C
ICE2A0565/165/265/365/765I/765P2 650 - - V Tj=110°C
ICE2B0565/165/265/365/765I/765P2
ICE2A0565G/0565Z
Drain Source Breakdown Voltage V(BR)DSS 800 - - V Tj=25°C
ICE2A180Z/280Z/380P2 870 - - V Tj=110°C
Drain Source ICE2A0565 RDSon1 - 4.7 5.5 : Tj=25°C
On-Resistance - 10.0 12.5 : Tj=125°C
ICE2A165 RDSon2 - 3 3.3 : Tj=25°C
- 6.6 7.3 : Tj=125°C
ICE2A265 RDSon3 - 0.9 1.08 : Tj=25°C
- 1.9 2.28 : Tj=125°C
ICE2A365 RDSon4 - 0.45 0.54 : Tj=25°C
- 0.95 1.14 : Tj=125°C
ICE2B0565 RDSon5 - 4.7 5.5 : Tj=25°C
- 10.0 12.5 : Tj=125°C
ICE2B165 RDSon6 - 3 3.3 : Tj=25°C
- 6.6 7.3 : Tj=125°C
ICE2B265 RDSon7 - 0.9 1.08 : Tj=25°C
- 1.9 2.28 : Tj=125°C
ICE2B365 RDSon8 - 0.45 0.54 : Tj=25°C
- 0.95 1.14 : Tj=125°C
ICE2A0565G RDSon9 - 4.7 5.5 : Tj=25°C
- 10.0 12.5 : Tj=125°C
ICE2A0565Z RDSon10 - 4.7 5.5 : Tj=25°C
- 10.0 12.5 : Tj=125°C
ICE2A180Z RDSon11 - 3 3.3 : Tj=25°C
- 6.6 7.3 : Tj=125°C
ICE2A280Z RDSon12 - 0.8 1.06 : Tj=25°C
- 1.7 2.04 : Tj=125°C
ICE2A765I RDSon13 - 0.45 0.54 : Tj=25°C
- 0.95 1.14 : Tj=125°C
ICE2B765I RDSon14 - 0.45 0.54 : Tj=25°C
- 0.95 1.14 : Tj=125°C
ICE2A765P2 RDSon15 - 0.45 0.54 : Tj=25°C
- 0.95 1.14 : Tj=125°C
ICE2B765P2 RDSon16 - 0.45 0.54 : Tj=25°C
- 0.95 1.14 : Tj=125°C
ICE2A380P2 RDSon17 - 1.89 2.27 : Tj=25°C
- 4.15 4.98 : Tj=125°C
52
2. FL DISPLAY
16ST85GINK (FL81)
1 43
Grid Assignment
16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G
( Upper display ) ( Lower display )

1-1B 2-1B 3-1B 4-1B 5-1B 1-1A 2-1A 3-1A 4-1A 5-1A
1-2B 2-2B 3-2B 4-2B 5-2B 1-2A 2-2A 3-2A 4-2A 5-2A
1-3B 2-3B 3-3B 4-3B 5-3B 1-3A 2-3A 3-3A 4-3A 5-3A
1-4B 2-4B 3-4B 4-4B 5-4B 1-4A 2-4A 3-4A 4-4A 5-4A
1-5B 2-5B 3-5B 4-5B 5-5B 1-5A 2-5A 3-5A 4-5A 5-5A
1-6B 2-6B 3-6B 4-6B 5-6B 1-6A 2-6A 3-6A 4-6A 5-6A
1-7B 2-7B 3-7B 4-7B 5-7B 1-7A 2-7A 3-7A 4-7A 5-7A
[ 16G~1G ]
Pin Connection
NOTE 1) F1,F2 : Filament

44443333333 333 2 1 1
Pin No. 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9~ 5 4 ~ 4 3 2 1 2) NP : No pin
3) NC : No connection
- 4) NX : No extend pin
R 5) DL : Datum Line
Connection LP E 6) LGND : Logic GND pin
GG V OS - TT 7) PGND : Power GND pin
FNNNNVDSECCDSS N N NNF 8) VH : High Voltage Supply pin
2 P PDDHDC T S P AA B X C PP1
9) VDD : Logic Voltage Supply pin
10) CP : Shift Register Clock
11) DA : Serial Data Input
12) TSA,B : Test pin
13) CS : Chip Select Input pin
14) RESET : Reset Input
15) OSC : Pin for self-oscillation
53
---MEMO---
54
BLOCK DIAGRAM
KEY MATRIX FLD HCT-18MS02T REMOCON
SDB TONE TUNED AUTO ST MONO TOTAL RAMDOM 1 FLD ALL SLEEP +HB(+26.5V)
+5.6D
+3.3SW
RELAY
AC
SMPS
±12VA
±7.5VA
+42V(FL FIL)
CONTROL
DATA & CLK
DATA
DATA
+9V_NSW SUB
EEPROM
RESET I2C
TRANS
M95040
S-80128ALMC
MCU
+3.3V_NSW
DOCKS COM BUF M3062LFGPGP

ROM/RAM: 256K/20K
DENON BUS BUF DATA & CLK
DATA & CLK

POWER SUPPLY BLOCK
DAB
DAB MODULE
CONTROL
venice 5.1
FM
H/P OUT
TUNER MODULE H/P AMP MUTE
AM/FM/RDS MONO MONO OUT

AMP
AM
REC OUT
(TAPE/MD)
CONTROL
OTW SD
CONTROL
RESET
DC PROTECT
PORTABLE IN M61531
EUR:65Wx2ch/4 ohm
JPN:80Wx2ch/4 ohm
(3.5mm JACK) DAB
TUMER
RELAY
PORTABLE IN
PHONO
PHONO
SP POWER AMP
CD AMP
AUX1
BUF DVOL TONE OPTIMISE MUTE TAS5630DKD
AUX2
NJM2068
NJM2068
CD Analog L/R IN
SWITCH
AUX1
(IPOD)
AUX2
(TAPE/MD)
* MD IN/OUT: JAPAN VERSION ONLY
55
LEVEL DIAGRAM
㪛㪩㪘㪄㪝㪈㪇㪎㩷㪣㪜㪭㪜㪣㩷㪛㪠㪘㪞㪩㪘㪤
㪝㪬㪥㪚㪫㪠㪦㪥㩷㪪㪮㪠㪫㪚㪟
㪫㪬㪥㪜㪩㩷㪧㪘㪚㪢㪫㪬㪥㪜㪩
㪛㪘㪙
㪛㪘㪙㩷㪬㪥㪠㪫
㪤㪘㪪㪫㪜㪩㪫㪦㪥㪜
㪧㪟㪦㪥㪦㩿㪤㪤㪀㪧㪟㪦㪥㪦㪭㪦㪣㪬㪤㪜㪚㪦㪥㪫㪩㪦㪣㪧㪦㪮㪜㪩㩷㪘㪤㪧
㪚㪛㪙㫌㪽㪽㪼㫉㪙㫌㪽㪽㪼㫉㪙㫌㪽㪽㪼㫉㪘㪤㪧㪤㪬㪫㪜㪪㪧㪶㪩㪜㪣㪘㪰
㪩㪠㪘㪘㪛㪦㪚㪢㪆㪘㪬㪯㪪㪧㩷㪦㪬㪫
㪚㪛㪧㪦㪩㪫㪘㪙㪣㪜
㪫㪘㪧㪜
㪘㪬㪯㪆㫀㪧㫆㪻㪤㪛㪟㪧㪶㪤㪬㪫㪜
㪟㪧㩷㪦㪬㪫
㪧㪦㪩㪫㪘㪙㪣㪜
㪫㪘㪧㪜㩿㪧㪙㪀㪝㪤㪬㪫㪜
㪤㪦㪥㪦㩷㪦㪬㪫
㪤㪛㩿㪧㪙㪀
䇭
㪫㪘㪧㪜㩿㪩㪜㪚㩷㪦㪬㪫㪀
㪤㪛㩿㪩㪜㪚㩷㪦㪬㪫㪀
㪍㪌㪮㪆㪋㫆㪿㫄㩷㪈㪍㪅㪈㪉㪭㩷㪄㪕㪉㪋㪻㪙
㪋㪋
㪉㪉
㪂㪉㪇㪂㪉㪇
㪏㪏
㪍㪍
㪋㪂㪉㪐㪻㪙㪋
㪉㪇㪅㪌㪻㪙㪤㪍㪈㪌㪊㪈㩷㪤㪸㫏㩷㫆㫌㫋㫇㫌㫋㩷㪋㪅㪉㪭㫉㫄㫊㪉
㪂㪈㪇㪂㪈㪇
㪏㪏
㪚㪛㩷㪤㪘㪯㩷㫀㫅㫇㫌㫋㪍㪍
㪈㪅㪎㪭㫉㫄㫊㩿㪋㪅㪍㪻㪙㪀㪋㩷㪋
㪉㪉
㪇㪇
㪉㪈㪭㫉㫄㫊㪉
㪋㪈㪏㪅㪍㪻㪙㪋
㪍㪟㪆㪧㩷㪦㪬㪫㩷㩷㪎㪉㪇㫄㪭㪆㪊㪉㫆㪿㫄㪍
㪚㪛㩷㪆㪤㪛㪆㪫㪘㪧㪜㪏㪫㪦㪥㪜㩷㩷㪂㪏㪻㪙㪂㪐㪻㪙㪏
㪉㪈㪇㫄㪭㪄㪈㪇㩷㪄㪈㪇
㪉㪉
㪛㪘㪙㩷㩷㪄㪈㪌㪻㪙㪋㪘㪬㪯㩷㪉㪈㪇㫄㪭㪄㪈㪋㪻㪙㪚㪛㪃㪤㪛㪃㪩㪜㪚㪃㪤㪦㪥㪦㩷㪦㪬㪫㪉㪈㪇㫄㪭㪋
㪫㪬㪥㪜㪩㩷㪊㪇㩼㩷㪤㪦㪛㩷㫀㫅㪍㩷㪧㪟㪦㪥㪦㪩㪜㪚㪦㪬㪫㩷㪉㪈㪇㫄㪭㪍
㫀㪧㪦㪛㩷㪄㪈㪌㪻㪙㪏㪏
㪄㪉㪇㪄㪉㪇
㪉㪉
㪋㪋
㪧㪟㪦㪥㪦㩷㪤㪘㪯㩷㫀㫅㫇㫌㫋㪍㪍
㪌㪇㫄㪭㪏㪏
㪄㪊㪇㪄㪊㪇
㪉㪉
㪋㪋
㪍㪂㪊㪏㪻㪙㪍
㪏㪏
㪄㪋㪇㪄㪋㪇
㪉㪉
㪋㪋
㪍㪍
㪏㪏
㪄㪌㪇㪄㪌㪇
㪧㪟㪦㪥㪦㩷㪪㪜㪥㪪㪜㪉㪉
㪉㪅㪌㫄㪭㪋㪋
㪍㪍
㪏㪏
㪄㪍㪇㪄㪍㪇
56
PRINTED WIRING BOARDS
MAIN PCB ASS'Y (1/2)
COMPONENT SIDE
57
MAIN PCB ASS'Y (2/2)
FOIL SIDE
58
FRONT PCB ASS'Y
COMPONENT SIDE
59
AMP PCB ASS'Y
COMPONENT SIDE FOIL SIDE
SMPS PCB ASS'Y
COMPONENT SIDE
60
NOTE FOR PARTS LIST
1. Parts for which "nsp" is indicated on this table cannot be supplied.
2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
3. Ordering part without stating its part number can not be supplied.
4. Part indicated with the mark "★" is not illustrated in the exploded view.
5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
6. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
● Resistors
Ex.: RN 14K 2E 182 G FR
Type Shape Power Resist- Allowable Others

and per- ance error
formance
RD : Carbon 2B : 1/8 W F : ±1% P : Pulse-resistant type

RC : Composition 2E : 1/4 W G : ±2% NL : Low noise type
RS : Metal oxide film 2H : 1/2 W J : ±5% NB : Non-burning type
RW: winding 3A : 1 W K : ±10% FR : Fuse-resistor
RN : Metal film 3D : 2 W M : ±20% F : Lead wire forming
RK : Metal mixture 3F : 3 W
3H : 5 W
* Resistance
1 8 2 1800ohm=1.8kohm
Indicates number of zeros after effective number.

2-digit effective number.
1 R 2 1.2ohm
1-digit effective number.

2-digit effective number, decimal point indicated by R.
: Units: ohm
● Capacitors
Ex.: CE 04W 1H 3R2 M BP
Type Shape Dielectric Capacity Allowable Others

and per- strength error
formance
CE : Aluminum foil 0J : 6.3 V F : ±1% HS : High stability type

electrolytic 1A : 10 V G : ±2% BP : Non-polar type
CA : Aluminium solid 1C : 16 V J : ±5% HR : Ripple-resistant type
electrolytic 1E : 25 V K : ±10% DL : For change and discharge
CS : Tantalum electrolytic 1V : 35 V M : ±20% HF : For assuring high requency
CQ : Film 1H : 50 V Z : ±80% U : UL part
CK : Ceramic 2A : 100 V : - 20% C : CSA part
CC : Ceramic 2B : 125 V P : +100% W : UL-CSA part
CP : Oil 2C : 160 V C : ±0.25pF F : Lead wire forming
CM: Mica 2D : 200 V D : ±0.5pF
CF : Metallized 2E : 250 V = : Others
CH : Metallized 2H : 500 V
2J : 630 V
* Capacity (electrolyte only)
2 2 2 2200μF 2 R 2 2.2μF
Indicates number of zeros after effective number. 1-digit effective number.
2-digit effective number. 2-digit effective number, decimal point indicated by R

･ Units:μF. ･ Units:μF.
* Capacity (except electrolyte)
2 2 2 2200pF=0.0022μF 2 2 1 220pF
Indicates number of zeros after efective number. Indicates number of zeros after effective numver.
(More than 2) (0 or 1)
2-digit effective number. 2-digit effective number.
･ Units:pF ･ Units:pF
･ When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.
61
PARTS LIST OF P.W.B. UNIT
＊ Parts for which "nsp" is indicated on this table cannot be supplied.
＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Note: The symbols in the column "Remarks" indicate the following destinations.
E2 : Europe model EK : U.K. model
MAIN PCB ASS'Y

Ref. No. Part No. Part Name Remarks Q'ty New
SEMICONDUCTORS GROUP
IC11 00D2630609002 OP AMP IC HVINJM2068DD
IC12 00D9430007108 OP AMP IC HVINJM2068MDTE1
IC13 00D9430059800 HEADPHONE IC HVINJM4556AL *
IC21 00D2631245009 6H VOLUME IC (10 INPUT, PLASTIC 80P QFP) CVIM61531FPR60G
IC22 00D9430005702 REGULATOR IC (-8V) HVIKA79L08AZT
IC23 00D9430005605 REGULATOR IC (+8V) HVIKA78L08AZT
IC31 234010016508S HEX INVERTER IC HVITC74VHCT04AFT
IC61 943239007750S HEX INVERTER IC HVI74LVC04ADT
IC62 943243010810D I.C U-COM (M3062LFGPGP Renesas) CVIANAM1497AT g
IC63 943249006970S I.C EEPROM (4K,SO8-8P) CVIM95040-WMN6TP
IC64 943239007760S REGULATOR IC (3.3V, DPAK-5) CVIKIA78R033F
IC65 00D2622977946 REGULATOR IC (3.3V SMD Type) BVIBA33BC0FP
IC66 943239007240M RESET IC 2.8V (50ms,C-MOS,SOT23-5P) CVIS80128ALMCJANT2
Q101-108 00D9430072502 CHIP TR HVTKTC2875B

Q301 00D9430058908 CHIP TR HVTKTA1504SYRTK
Q302 00D9630121606 CHIP TR HVTKRC107S
Q371-373 00D9630121606 CHIP TR HVTKRC107S
Q571,572 00D9430058908 CHIP TR HVTKTA1504SYRTK
Q573,574 00D2730464901 CHIP TR HVTKTC3875SYRTK
Q575 00D9430038009 CHIP TR HVTKRA102S
Q606-607 00D9630121606 CHIP TR HVTKRC107S
Q613 00D9430072609 T.R HVTKTC3199YT
Q813 00D9430058908 CHIP TR HVTKTA1504SYRTK
D101 00D2760717903 CHIP DIODE HVD1SS355T

D201,202 00D2760717903 CHIP DIODE HVD1SS355T
D303,304 90M-HD302150R ZENER DIODE HVDMTZJ6.8BT
D371-374 00D2760717903 CHIP DIODE HVD1SS355T
62
D610 00D9430087607 ZENER DIODE HVDMTZJ6.2BT
RESISTORS GROUP
R551-554 RES , CHIP 1/4W CRJ14CJ3R3T
R535-538 nsp METAL(OXIDE)FILM RES 5% KRG1SANJ4R7RT
R626 nsp CHIP RES CRJ10DJ103T
R609 nsp CHIP RES EK CRJ10DJ103T
R624 nsp CHIP RES E2 CRJ10DJ103T
CAPACITORS GROUP
C101,102 nsp CERAMIC CAP CCKT1H101KB
C103,104 nsp ELECT CAP CCEA1HKS100T
C107 nsp CHIP CAP CCUS1H103KC
C108 nsp ELECT CAP CCEA1HH220T
C109,110 nsp ELECT CAP CCEA1AKS221T
C111-112 nsp CAP , METALLIZED FILM (6800pF/100V) CCME2A682JXT
C113-114 nsp MYLAR CAP HCQI1H682JZT
C115,116 nsp METALLIZED FILM CAP (100V/0.018UF, J) CCME2A183JXT *
C117,118 nsp MYLAR CAP HCQI1H392JZT
C119,120 nsp ELECT CAP CCEA1HH100T
C122 nsp ELECT CAP CCEA1HH220T
C123,124 nsp CHIP CAP CCUS1H104KC
C131 nsp ELECT CAP CCEA1HH1R0T
C135,136 nsp ELECT CAP CCEA1HH4R7T
C153,154 nsp ELECT CAP CCEA1CH101T
C201-204 nsp CHIP CAP CCUS1H104KC
C205 00D2544692901 ELECT CAP (10uF/63V RFO) CCEA1JRFO100T s
C210 00D2544692901 ELECT CAP (10uF/63V RFO) CCEA1JRFO100T s
C213 00D2544694912 ELECT CAP (220uF/25V, RFO) CCEA1ERFO221T s
C221,222 00D2544694912 ELECT CAP (1000uF/25V, RFO, 12.5X20) CCEA1ERFO102E
C223-225 nsp CHIP CAP CCUS1H181JA
C227 nsp ELECT CAP CCEA1CH470T
C229 nsp CHIP CAP CCUS1H181JA
63
C237 00D2544693939 ELECT CAP(100uF/50V RFO) CCEA1HRFO101T s
C241 00D2544693900 ELECT CAP (ELNA, RFO, 50V/22UF) CCEA1HRFO220T
C243 00D2544693926 ELECT CAP (47uF/50V RFO) CCEA1HRFO470T
C246-249 nsp ELECT CAP CCEA1HH4R7T
C250 nsp MYLAR CAP HCQI1H223JZT
C251 nsp METALLIZED FILM CAP CCME2A473JXT
C252,253 nsp METALLIZED FLIM CAP (100V/0.22UF) CCME2A224JXT
C254 nsp METALLIZED FILM CAP CCME2A473JXT
C255 nsp MYLAR CAP HCQI1H223JZT
C256 943134006940S ELECT CAP(47uF/50V ROA) CCEA1HROA470T *
C258 943134006940S ELECT CAP(47uF/50V ROA) CCEA1HROA470T *
C261,262 nsp CERAMIC CAP (100PF/50V) CCBS1H101KBT
C265,266 00D2544693900 ELECT CAP (ELNA, RFO, 50V/22UF) CCEA1HRFO220T
C267,268 nsp METALLIZED FILM CAP (1000pF APSV) CCMP2A102JN09T *
C273,274 nsp ELECT CAP CCEA1HH4R7T
C275-284 nsp ELECT CAP CCEA1HH100T
C301,302 nsp CHIP CAP CCUS1H470JA
C351,352 nsp CHIP CAP CCUS1H181JA
C573,574 nsp ElECT CAP (220uF/25V, RFO) CCEA1ERFO221T
C575,576 943139001280S METALLIZED FILM CAP CCME2A103JXT
C604 nsp ELECT CAP CCEA1AH471T
C607 00D2544693939 ELECT CAP(100uF/50V RFO) CCEA1HRFO101T s
C608 nsp ELECT CAP CCEA1AH471T
C617 nsp CHIP CAP (15PF/50V) CCUS1H150JA
C636-639 nsp CHIP CAP (2012 SIZE) CCUC2A103KC
64
C640 nsp CHIP CAP CCEA1CH470T
OTHERS PARTS GROUP

BD81 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z
BD02-04 nsp CHIP FERRITE BEAD(220ohm, 2012) CLZ9R006Z
BD82-85 nsp CHIP FERRITE BEAD(220ohm, 2012) CLZ9R006Z
BN61 nsp 7P WIRE ASS'Y(120mm, 2.0mm) CWB1C90712047
BR21-24 nsp EARTH PLATE HJT1A025
CN82 nsp LOCKING TYPE , STRAIGHT WAFER , 2MM CJP07GI236ZW

CN96 nsp LOCKING TYPE , STRAIGHT WAFER , 2mm CJP05GI236ZW
JK11 nsp JACK, RCA(2P, RCA-215-13, W/R, NO PLATE) CJJ4N089Z

JK12 nsp BOARD JACK CJJ4M046Z
JK21,22 nsp BOARD JACK CJJ4P048Z
JK31,32 nsp STEREO JACK CJJ2D008Z
JK51 943643007770S 4P SPK TERMINAL ( RD/BK, RD/BK, 94V-O ) CJJ5P031Z *
L101,102 00D9430193601 TOROIDAL COIL CLU9S004Z *
RL51 00D9430060608 RELAY HSL4A004ZU
WC11 nsp FEMALE HEADER (14P,2.54mm) , STRAIGHT CJP14GA221ZB

TYPE
TYPE
TYPE
TYPE
WF31 nsp WAFER , CARD CABLE CJP15GA115ZY
WN21 nsp WAFER , CARD CABLE CJP13GA115ZY

WN31 nsp WAFER , CARD CABLE CJP15GA115ZY
WN32 nsp WAFER CJP09GA117ZY
WN81 nsp WAFER CJP21GA117ZY
WP11 nsp PIN HEADER(14PIN, 2.54mm, ANGLE) CJP14GB142ZB
X202 943141007780S X-TAL , HC-49/S (14.7456MHz 18pF) COX14745E180C *
65
FRONT PCB ASS'Y
IC71 943239007760S REGULATOR IC (3.3V, DPAK-5) EK CVIKIA78R033F
IC72 943239008020S REGULATOR IC (ADJ, DPAK-5) EK CVIKIA78R000F
IC91 00D2631100018 REGULATOR IC +6V HVIKIA7806API
Q701 00D9430004305 TR EK HVTKRC107MT

Q805,806 00D9430004305 TR HVTKRC107MT
Q807,808 00D9430154200 TR HVTKRA102MT
Q809,810 00D9630121606 CHIP TR HVTKRC107S
Q901 00D9430072609 TR HVTKTC3199YT
Q903 00D9430072609 TR HVTKTC3199YT
Q910 00D9430004305 TR HVTKRC107MT
D702 00D9430182502 RECT DIODE EK CVD1N4003ST

D801 00D9430106203 2COLOR LED HVDSPR39MVW3
D902 00D9430182502 RECT DIODE CVD1N4003ST
D905-911 00D9430041902 SCHOTTKY DIODE HVD1N5819T
D921-923 00D9430182502 RECT DIODE CVD1N4003ST
D924 00D9430086404 DIODE HVD1SS133MT
D938 00D9430086404 DIODE HVD1SS133MT
RESISTORS GROUP
VR81 943667007540S ENCODER VOLUME CSR2A052Z *
VR82 943667007550S ENCODER , FUNCTION (16MM, 24PULSES) CSR2A051Z *
CAPACITORS GROUP
C701,702 nsp ELECT CAP EK CCEA1HKS4R7T
C703 nsp CERAMIC CAP EK CCBS1H104ZFT
C703 nsp COPPER WIRE C3A206
C705 nsp ELECT CAP EK CCEA0JH471T
C706 nsp ELECT CAP EK CCEA0JKS470T
C707,708 nsp CERAMIC CAP EK CCBS1H103ZFT
C710 nsp ELECT CAP EK CCEA0JKS470T
C713,714 nsp CERAMIC CAP EK CCBS1H104ZFT
C715 nsp COPPER WIRE E2 C3A206
C716 nsp ELECT CAP EK CCEA1AH221T
C801 nsp ELECT CAP CCEA1CKS101T
C802 nsp CERAMIC CAP CCBS1H103ZFT
C803 nsp CERAMIC CAP (47PF/50V) CCBS1H470JT
C805-807 nsp CERAMIC CAP (100PF/50V) CCBS1H101KBT
C808-810 nsp CERAMIC CAP CCBS1H104ZFT
C813,814 nsp CERAMIC CAP CCBS1H103ZFT
C819,820 nsp ELECT CAP CCEA1HKS4R7T
C824,825 943139001280S METALLIZED FILM CAP CCME2A103JXT
66
C830 nsp CERAMIC CAP (1000PF/50V) CCBS1H102KBT
C832 nsp ELECT CAP CCEA1HKS1R0T
C833 nsp CERAMIC CAP (1000PF/50V) CCBS1H102KBT
C834 nsp ELECT CAP CCEA1CKS101T
C901 00D2544693939 ELECT CAP(100uF/50V RFO) CCEA1HRFO101T
C904 00D2544693939 ELECT CAP(100uF/50V RFO) CCEA1HRFO101T
C912 nsp ELECT CAP CCEA1EH222E
C918 nsp ELECT CAP CCEA1EH222E
z C922 00D9430024408 CERAMIC CAP (X1/Y2/SC) KCKDKS472ME
z C952 90M-OF100550R CAP , X2 CCQF2E104KZC
OTHERS PARTS GROUP

BN82 nsp 7P SHIELD WIRE ASS'Y(180mm, 2.0mm) CWB1B90718047001
BN83 nsp 5P WIRE ASS'Y(100mm, 2.0mm) CWB1C90510047
BR71 BRACKET , PCB CMD1A629

BR72 BRACKET , PCB CMD1A569
BR81 nsp EARTH PALTE HJT1A025
BR82,83 nsp FLT BRACKET CMD1A468
CN71 nsp 2.54mm 30PIN WAFER EK CJP30GA221ZB

CN93 nsp WAFER CJP02GA89ZY
FL81 00D3938086009 V.F.D , DCD-510AE (16ST85GINK) CFL16ST85GINK

z F801 nsp FUSE HOLDER KJCFC5S
z F801 00D9430207208 FUSE 1.25AL/250V KBA2C1250TLEY *
JK81,82 00D9430105204 HEADPHONE JACK (SILVER) HJJ2D003Y

JK91 00D9430199206 AC OUTLET (EUR/1P) KJJ7A022Z *
JK93 00D2033905015 AC INLET (250V/2.5A PCB MOUNT TYPE) CJJ8A012Z
L803 nsp CORE BEAD KLZ9H001Z

L801,802 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z
L903 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z
RC81 00D9430194706 REMOCON SENSOR CRVKSM603TH2E
RL91 00D9430194900 POWER RELAY CSL1E002ZE
S801-805 00D9430004402 TACT SW CST1A012ZT

S809 00D9430004402 TACT SW CST1A012ZT
z T902 943101007910D SUB TRANS 6V (EUR) DCD710AE2/E1C CLT5I015ZE *
WF81 nsp WAFER CJP21GA117ZY

WP82 nsp PIN HEADER (08P, 2.54mm) , ANGLE TYPE CJP08GB142ZB
67
SMPS PCB ASS'Y
IC91 943231007650S VOL-REGULATOR IC (15V TO-220IS-4) CVIKIA7815AP *
IC92 943235003200S COOLSET IC CVIICE2B265 *
IC93 943235003210S PWM CONTROLLER IC (PG-DIP-8) CVIICE2QS01 *
IC94 943231007660S REGULATOR IC ( 24V, TO-92L ) CVIL78L24AB *
IC96 90M-HC300770R REGULATOR IC HVIKIA431BAT
IC97 00D9430206908 REGULATOR IC (12V OUTPUT LOW DROP) HVIKIA78R12PI
IC98 00D9430183909 REGULATOR IC HVIKIA7912PI
PC91,92 00D9430038601 PHOTO COUPLER HVIPC17L1CB
Q933,934 943219007680S T.R ( TO-126, EPITAXIAL PLANAR NPN ) CVTKTD1691Y

Q903 943229007670S F.E.T , SPW20N60C3 (N-CH, P-TO247, CVTSPW20N60C3 *
POWER,INFINEO
Q931 00D9430107804 T.R HVTKRC102MT
Q935 943213003350S SWITCHING TR CVTKTN2222A *
D902 00D9430040806 SCHOTTKY DIODE HVDUF4004T *

D904-908 00D9430040806 SCHOTTKY DIODE HVDUF4004T *
D911 00D9430182609 DIODE HVD1SS133MT
D912 90M-HD302310R ZENER DIODE HVDMTZJ27BT
D913 00D9430195909 ZENER DIODE HVDMTZJ16BT
D914,915 00D9430087102 ZENER DIODE HVDMTZJ20BT
D920-924 00D9430182609 DIODE HVD1SS133MT
D931 90M-HD201950R SCHOTTKY DIODE (60V/1A) HVD11EQ06T *
D939 00D9430182609 DIODE HVD1SS133MT
D940,941 00D9430040709 SCHOTTKY DIODE HVDUF4007T *
D946 00D9430182609 DIODE HVD1SS133MT
D950 943202007690S ZENER DIODE (ROHM,18V) HVDMTZJ18BT
D951 943203003140S SCHOTTKY DIODE (20A, 200V) CVDFCH20A20 *
z DB91 943203003170S BRIDGE DIODE HVDGBJ606 *
RESISTORS GROUP
R910 nsp WIRE WOUND RES (1W/0.5ohm) CRW1PJR50V
R911 nsp METAL OXIDE FILM RES KRG2SANJ683H
R920,921 nsp WIRE WOUND RES CRW1PJR15V
R968 nsp METAL OXIDE FILM RES CRG1ANJ100R
R970 nsp METAL OXIDE FILM RES (2W, 2.2K) CRG2SANJ222RT
R991 nsp METAL FILM RES (1/2W , 1M OHM) KROS1TJ105V
R995 nsp METAL OXIDE FILM RES (2W, 75ohm) CRG2SANJ750RT
CAPACITORS GROUP
C901 943134007790S ELECT CAP (K3J, 450V/390UF, 105, 35X50) CCET450VK3J391AK *
C903 00MOF15223541 APSV223J0.022uF (TF) 100VPP CCMPA223JN09T f
C905 nsp MONO CAP (50V.102) CCUMT1H102KB
68
SMPS PCB ASS'Y
IC91 943231007650S VOL-REGULATOR IC (15V TO-220IS-4) CVIKIA7815AP *
IC92 943235003200S COOLSET IC CVIICE2B265 *
IC93 943235003210S PWM CONTROLLER IC (PG-DIP-8) CVIICE2QS01 *
IC94 943231007660S REGULATOR IC ( 24V, TO-92L ) CVIL78L24AB *
IC97 00D9430206908 REGULATOR IC (12V OUTPUT LOW DROP) HVIKIA78R12PI
IC98 00D9430183909 REGULATOR IC HVIKIA7912PI
PC91,92 00D9430038601 PHOTO COUPLER HVIPC17L1CB
Q933,934 943219007680S T.R ( TO-126, EPITAXIAL PLANAR NPN ) CVTKTD1691Y

Q903 943229007670S F.E.T , SPW20N60C3 (N-CH, P-TO247, CVTSPW20N60C3 *
POWER,INFINEO
Q931 00D9430107804 T.R HVTKRC102MT
Q935 943213003350S SWITCHING TR CVTKTN2222A *

D904-908 00D9430040806 SCHOTTKY DIODE HVDUF4004T *
D911 00D9430182609 DIODE HVD1SS133MT
D912 90M-HD302310R ZENER DIODE HVDMTZJ27BT
D913 00D9430195909 ZENER DIODE HVDMTZJ16BT
D914,915 00D9430087102 ZENER DIODE HVDMTZJ20BT
D920-924 00D9430182609 DIODE HVD1SS133MT
D931 90M-HD201950R SCHOTTKY DIODE (60V/1A) HVD11EQ06T *
D939 00D9430182609 DIODE HVD1SS133MT
D946 00D9430182609 DIODE HVD1SS133MT
D950 943202007690S ZENER DIODE (ROHM,18V) HVDMTZJ18BT
D951 943203003140S SCHOTTKY DIODE (20A, 200V) CVDFCH20A20 *
z DB91 943203003170S BRIDGE DIODE HVDGBJ606 *
RESISTORS GROUP
R910 nsp WIRE WOUND RES (1W/0.5ohm) CRW1PJR50V
R920,921 nsp WIRE WOUND RES CRW1PJR15V
R968 nsp METAL OXIDE FILM RES CRG1ANJ100R
R970 nsp METAL OXIDE FILM RES (2W, 2.2K) CRG2SANJ222RT
R991 nsp METAL FILM RES (1/2W , 1M OHM) KROS1TJ105V
R995 nsp METAL OXIDE FILM RES (2W, 75ohm) CRG2SANJ750RT
CAPACITORS GROUP
C901 943134007790S ELECT CAP (K3J, 450V/390UF, 105, 35X50) CCET450VK3J391AK *
C903 nsp MYLAR CAP (0.022uF/100V) CCQI2A223JZT
68
C906 nsp MONO CAP CCUMT1H104KB
C907 nsp ELECT CAP CCEA1HH220TS
C908 nsp MONO CAP (4700pF/100V) CCUMT2A472KC
C909 nsp MONO CAP (0.47uF/50V) CCUMT1H474KC
C910 nsp CERAMIC CAP CCKT3A222KBL
C912 nsp MONO CAP (2200pF/100V) CCUMT2A222KC
C913 nsp MLCC CAP (100PF/50V) CCUMT1H101KC
C914 nsp CERAMIC CAP (220PF/1KV) CCKT3A221KB
C915 nsp ELECT CAP CCEA1HH220TS
C916 nsp MONO CAP (470PF/50V) CCUMT1H471KC
C918,919 nsp MONO CAP CCUMT1H104KB
C922 943134003030S ELECT CAP (KRM, 100V/1UF, 105C, 5X11) CCEA2AH1R0TS *
C931 nsp ELECT CAP (1000uF/10V, 10X16, KLH) CCEA1AKLH102EKS *
C932 nsp ELECT CAP CCEA1HH1R0TS
C933 nsp ELECT CAP (10V/2200UF, 105C, 10X20) CCEA1AH222ES
C935 nsp ELECT CAP CCEA1JH470TS
C935 nsp ELECT CAP (47uF/63V, 8X12, KLH) CCEA1JKLH470TKS
C936 00D2544692930 ELECT CAP(47uF/63V RFO)
C940 nsp ELECT CAP (100uF/16V, 6.3X11, KLH) CCEA1CKLH101TKS
C948 nsp ELECT CAP (100uF/25V, 6.3X11, KLH) CCEA1EKLH101TKS
C949 943134008030S ELECT CAP(56uF/25V RJH) *
C950 943134006960S ELECT CAP (470uF/35V RJH) *
C951 943134008040S ELECT CAP(220uF/25V RJH) *
C960 nsp ELECT CAP CCEA1HH1R0TS
C962 nsp CAP , CHIP(3216 SIZE) CCUP2A104KC
C967 nsp ELECT CAP (2200uF/35V, 16X31.5, KLH) CCEA1VKLH222EKS
C968 nsp ELECT CAP CCEA1HH102ES
C969-972 nsp MONO CAP CCUMT1H104KB
C974,975 nsp COPPER WIRE C3A206
C976-980 nsp MONO CAP CCUMT1H104KB
C985 00D2544692930 ELECT CAP(47uF/63V RFO)
OTHERS PARTS GROUP

BN91 nsp 7P WIRE ASS'Y(220mm, 2.0mm) CWB1E90722058
CN90 nsp WAFER KJP02KA060ZY

CN91 nsp LOCKING TYPE , STRAIGHT WAFER, 2.5MM CJP07GI237ZW
CN92 nsp LOCKING TYPE , STRAIGHT WAFER , 2MM CJP07GI236ZW
CN93 nsp LOCKING TYPE , STRAIGHT WAFER , 2.5MM CJP05GI237ZW
z CX91 nsp POLYPROPYLENE FILM CAP CCQF2E224KZE

z CX92 nsp POLYPROPYLENE FILM CAP HCQF2E104KZE
z CY91,92 nsp CERAMIC CAP (400V Y-CAP) CCKDHS102ME
z CY94 nsp CERAMIC CAP (400V Y-CAP) CCKDHS222ME
FH91,92 nsp FUSE HOLDER KJCFC5S
z F901 943652008050S FUSE (215 Series, 250V,3.15A) KBA2C3150TLHEY *
69
z LF91,92 943111007730S LINE FILTER ( 22mH, RING-615 ) CLZ9Z113Z
L921 943111003310S CHOKE COIL (20uH) CLZ9Z074Z *

L922 943111007720S CHOKE COIL ( 220uH ) CLZ9Z112Z *
L928 943111003330S CHOKE COIL (7UH) CLZ9Z090Z *
TF91 943102007610D SWITCHING TRANS EE1312 V-TYPE CLT9Z053ZE *

TF92 943102007620D SWITCHING TRANS EE2525W V-TPYE CLT9Z054ZE *
TF93 943102007630D SWITCHING TRANS EER4042 H-TYPE CLT9Z055ZE *
TH91 00D9430035206 THERMISTOR NTC (10MM PITCH) KRT5D15MSFC
TS91 943252007740S THERMAL PROTECTOR (100'C, 70mm) CRTST22100070W *
z VT91 943251003480S VARISTOR CRVSVC471D14A
BD90-99 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z *
70
AMP PCB ASS'Y
IC51,52 00MHC10102090 OP AMP IC HVINJM2068MDT
IC53 943231007700S REGULATOR IC (12V, DPAK-5) CVIKIA78R12F
IC54 943235007710S CLASS-D DIGITAL AMP IC (300W, DKD-44P) CVITAS5630DKD

CAPACITORS GROUP
C512 00D9430185402 ELECT CAP (ELNA RFO 100uF/25V) CCEA1ERFO101T
C515 00D2544693939 ELEC CAP ELNA RFO SERIES 100uF/50V CCEA1HRFO101T
C518-521 00D2544693900 ELECT CAP (ELNA, RFO, 50V/22UF) CCEA1HRFO220T
C523 nsp CHIP CAP (25V/4.7uF, 2125 SIZE) CCUC1E475KC
C525 nsp CHIP CAP (25V/4.7uF, 2125 SIZE) CCUC1E475KC
C529 00D2544694912 ElECT CAP (220uF/25V, RFO) CCEA1ERFO221T
C532 943134007870S ELECT CAP (1800uF/35V, ELNA, RJF, 16X25) CCEA1VRJF182E *
C536 nsp CHIP CAP (50V/4.7uF, 3216 SIZE) CCUP1H475KC
C543,544 nsp CHIP CAP (50V/4.7uF, 3216 SIZE) CCUP1H475KC
C551 943134007870S ELECT CAP (1800uF/35V, ELNA, RJF, 16X25) CCEA1VRJF182E *
C554 nsp POLYESTER CAP (100V/0.47uF, Panasonic CCME2A474JO14 *
ECQV Type)
ECQV Type)
C558-561 nsp CHIP CAP (2012 SIZE) CCUC2A103KC
ECQV Type)
ECQV Type)
71
C590,591 943134006960S ELECT CAP (1000uF/50V, ELNA, RFO) *
C631-634 nsp CHIP CAP (330pF/100V,2012 SIZE) CCUC2A331JA
C651-655 nsp CAP CAP 0.1UF/50V/2012 CCUC1H104KC
OTHERS PARTS GROUP

BD51 nsp CHIP FERRITE BEAD(220ohm, 2012) CLZ9R006Z
BD52-57 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z *
BD59 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z *
BD60 nsp CHIP FERRITE BEAD(60ohm, 4516) CLZ9Z014Z *
CN91 nsp LOCKING TYPE , STRAIGHT WAFER, 2.5MM CJP07GI237ZW
L501-504 00MLC11034420 POWER INDUCTOR COIL CLZ9Z111Z
WP51 nsp PIN HEADER(6P, 2.54mm) CJP06GB142ZB

WP52 nsp PIN HEADER(12PIN, 2.54mm, ANGLE) CJP12GB142ZB
72
WIRING DIAGRAM
AC100V~230V
TUNER MODULE
CONNECT WITH
AC IN
AC OUTLET
AMP BOARD
PHONO B'D
CONNECT WITH
MAIN B'D
DAB BOARD
WP52 WC52
13
1
POWER B'D WC82
15
1
AMP B'D
CONNECT WITH
WN31
PHONO BOARD
CN93
WN21
2
13
1
WC11 WP11
CN91
WP82
WP51 WC51
CONNECT WITH
WN81
1
AMP BOARD
21
1
CN96
BN96
DAB B'D
5
BN61
CN82
1
1
BN91
7
1
CN90
CN92
SMPS B'D CN93

7
DENON VOLUME 1
SOURCE 7
SDB/TONE TUNER ---- PRESET / TUNING---- AUTO PRESET
BN82
21
1
WF81
ON/ STANDBY
PORTABLE IN PHONES
DRA-F107
FRONT B'D
BN83
5
AM-FM STEREO RESEIVER
73
EXPLODED VIEW
WARNING:
Parts marked with this symbol have critical
characteristics.
Use ONLY replacement parts recommended by
the manufacturer.
74
PARTS LIST OF EXPLODED VIEW
＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
BK : Black model SP : Premium Silver model

C2A nsp FRONT PCB ASS'Y E2 CIP12218B 1 *
C2A nsp FRONT PCB ASS'Y EK CIP12218C 1 *
C2 - FRONT PCB
C6 - POWER PCB
C9 - DAB PCB EK
C8A nsp MAIN PCB ASS'Y E2 CIP12217B 1 *

C8A nsp MAIN PCB ASS'Y EK CIP12217C 1 *
C4 - SUB PCB
C8 - MAIN PCB
C11 - PHONO PCB
C13 - UPDATE PCB
C3 nsp SMPS PCB ASS'Y CIP12227B 1 *
C7 nsp AMP PCB ASS'Y CIP12242B 1 *
P1 943416007600D WINDOW CGU1A440Y 1 *

P2 943443006530D INNER PANEL BK CGW1A484B28 1 *
P2 943443006540D INNER PANEL SP CGW1A484RGG45 1 *
P3 943481000370D LENS CGL1A230A14 1
P4 943412006550D 5P KNOB BK CBT1A1115MBC57 1 *
P4 943412007590D 5P KNOB SP CBT1A11157MBC22 1 *
P5 00D9430094506 FOOT CKL1A189 4
P6 943471006570D CUSHION CHG1A285 4
M1 00D1120884228 KNOB(F) ASSY BK CGK00D1120884228D 1 *

M1 00D1120884215 KNOB(F) ASSY SP CGK00D1120884215D 1
M2 00D1120980119 VOLUME KNOB ASSY BK CGK00D1120980119D 1 *
M2 00D1120980106 VOLUME KNOB ASSY SP CGK00D1120980106D 1
M3 943402006580D FRONT PANEL (AL) BK E2 CKM1A217ZC45 1 *
M3 943402006590D FRONT PANEL (AL) SP E2 CKM1A217ZC62 1 *
M3 943402007920D FRONT PANEL (AL) BK EK CKM1A217YC45 1 *
M3 943402007930D FRONT PANEL (AL) SP EK CKM1A217YC62 1 *
M4 943412006440D POWER KNOB ASSY BK CBY1A049ZA 1 *
M4 943412006450D POWER KNOB ASSY SP CBY1A049YA 1 *
M5 nsp FIP BRACKET CMD1A468 2 *
M6 nsp EARTH PLATE CMC1A371 1 *
M7 943403006630D TOP CABINET BK CKC1A198B49 1 * s
M7 943403006640D TOP CABINET SP CKC1A198G60 1 * s
M8 nsp SCREW COVER CMD1A495 1 *
M9 nsp MAIN CHASSIS CUA1A300 1 *
M10 nsp PC COVER CMX1A268 1 *
M11 nsp HEAT SINK CMY1A331 1 *
M12 nsp PCB BRACKET CMD1A629 2
M13 nsp PCB BRACKET CMD1A569 2
M14 943406007940D REAR PANEL EK CKF1A406Z 1 *
M14 943406006650D REAR PANEL E2 CKF2A406Z 1 *
M15 nsp GROUND TERMINAL KMA1A006 1
75
M16 nsp WASHER EK CNW1A052 1 s
M17 nsp DAB NUT EK CNE1A009 1
M18 nsp PC INSULATOR CMX1A274 1 *
M19 nsp BRACKET SHIELD CMD1A723 1 *
C1 943172007420D FIP CFL16ST85GINK 1

C10 943183007950S DAB EK CNVF2025-1V328A 1
C12 00D9430055202 TUNER PACK CNVMV114MA1-19(E2/ 1
EK)
z C14 943611007960S AC CORD E2 CJAZB108ZV(E2) 1
z C14 943611000210S AC CORD EK CJA2E106ZV(EK) 1
SCREWS
S1 nsp SCREW BK CTBD3+8JFZR 9
S1 nsp SCREW SP CTBD3+8JFN 9
S2 nsp SCREW CTB3+6FFZR 10
S3 nsp SCREW CTB3+8JFZR 11
S4 nsp SCREW CTS3+8JR 3
S5 nsp SCREW CTB3+10JR 9
S6 nsp SCREW CTW3+8JR 6
S7 nsp SCREW SP CTB3+10JFZR 10
S7 nsp SCREW BK CTB3+10JFZR 9
S8 nsp SCREW BK CTWD4+6FFZR 2
S8 nsp SCREW SP CTWD4+6FFN 2
S9 nsp SCREW CTB3+6JR 2
76
PACKING VIEW
211
210
212
201 209
214
215
213
216 216
214
215
PARTS LIST OF PACKING & ACCESSORIES

BK : Black model SP : Premium Silver model
s
201 nsp POLY BAG CPB1A190Z 1 *
202 943541007970D INST MANUAL(E2/EK) CQX1A1464Z 1 * s
203 nsp S.S.LIST(EX) - 1
204 nsp BATTERY (SIZE 'AAA') - 1
205 943307007900D REMOCON(RC1127) CARTDRAF107BK 1 *
206 00D9430113500 ANT.AM LOOP CSA1A020Z 1 *
207 00D9430113403 FM 1 POLE ANT. CSA1A018Z 1 *
208 943429007990S ANT.DAB T EK CSA1A036Z 1 *
209 943611000190S CORD POWER E2 E2 CJA2B108ZV 1 *
209 943611000210S CORD POWER EK EK CJA2E106ZV 1 *
210 943535007470D POLY BAG CPB1A184Z 1 * s
211 943533007480D SNOW PAD CPS1A852 1 *
212 943533007490D SNOW PAD CPS1A853 1 *
213 943531008000D OUT CARTON BOX E2 CPG1A898X 1 *
213 943531008010D OUT CARTON BOX EK CPG1A898W 1 *
214 nsp POS LABEL SPE2 CQB1A943Z 2 *
214 nsp POS LABEL BKE2 CQB1A943Y 2 *
214 nsp POS LABEL SPEK CQB1A943X 2 *
214 nsp POS LABEL BKEK CQB1A943W 2 *
215 nsp CONTROL LABEL SPE2 CQB1A627 2 *
215 nsp CONTROL LABEL BKE2 CQB1A627 2 *
215 nsp CONTROL LABEL SPEK CQB1A627 2 *
215 nsp CONTROL LABEL BKEK CQB1A627 2 *
216 nsp COLOR LABEL SP CQB1A882Z 1 *
77
NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the unit to the customer, make sure you
make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps,
or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.
WARNING:
DO NOT return the unit to the customer until the problem is
located and corrected.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM
M=1,000,000 OHM
ALL CAPACITANCE VALUES IN MICRO FARAD.
P=MICRO-MICRO FARAD
EACH VOLTAGE AND CURRENT ARE MEASURED AT
NO SIGNAL INPUT CONDITION.
CIRCUIT AND PARTS ARE SUBJECT TO CHANGE
WITHOUT PRIOR NOTICE.
78
1 2 3 4 5 6 7 8
18
19
16
20 15 17
5
6
A
4
21
22
17
8
9
10
14 13
Lch SIGNAL LINE

Rch SIGNAL LINE
SCHEMATIC DIAGRAMS (1/4)

MAIN UNIT
s DRA-F107/DRA-F107DAB
1 2 3 4 5 6 7 8
1
2
3
A
Lch SIGNAL LINE

Rch SIGNAL LINE

FRONT UNIT
DRA-F107/DRA-F107DAB
1 2 3 4 5 6 7 8

SMPS UNIT
1 2 3 4 5 6 7 8
11
12
Lch SIGNAL LINE

Rch SIGNAL LINE

AMP UNIT

Hfe Denon Dra-F107 F107dab Service en

Uploaded by

Copyright:

Available Formats

Hfe Denon Dra-F107 F107dab Service en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hfe Denon Dra-F107 F107dab Service en

Uploaded by

Copyright:

Available Formats

Ver.

LEAKAGE CURRENT CHECK

◎ Heed the cautions! ◎ Inspect for safety after servicing!

Wire arrangement viewed from the top

Front Panel side

Back Panel side

FRONT PANEL ASSY AMP PCB REAR PANEL

SMPS PCB MAIN PCB

Check Power Supply Voltages for System uCOM.

Check Reset signal for System uCOM.

Check Oscillation waveform.

Check Power 50/60 Signal

Check Power Supply Voltages for FLD Check Soldering.

Check Reset Signal for FLD Check Soldering.

Check FLD Dirive Signal for FLD Check Soldering.

Check Power Supply Voltages for Digital Block Check Soldering.

Check Protect Signal for System uCOM. Check Soldering.

Check Protect Signal for D.Power Amp Check Soldering.

Check Control Singal for DC Protect Check Soldering.

Check Protect Signal for System uCOM. Check Soldering.

Check Control Signal for DENON BUS Check Soldering.

4. The Key Operation don't work

5. The Remote Control Operation don't work

Check Signal for Remote Control Check Soldering.

Check Power Supply Voltages for FUNCTION IC Check Soldering.

Check Control Signal for FUNCTION IC Check Soldering.

Check Audio function Mute Signal. Check Soldering.

Check SPEAKER RELAY control Signal Check Soldering.

(2) AM/FM TUNER-in

Check Power Supply Voltages for AM/FM TUNER. Check Soldering.

Check Analog Audio Data output from Prtable-in

Check Analog Audio Data input for FUNCTION IC Check Soldering.

Check Controll Signal for DAB TUNER. Check Soldering.

Check Analogl Audio Data output from DAB TUNER

Check Analog Audio Data input for FUNCTION IC

(5) iPod PLAY

Check Control Signal for iPod Dock Check Soldering.

Check Analog signal output from iPod Dock Check Soldering.

Check Power Supply Voltages for PHONO Check Soldering.

(7) Head Phone OUT

Check Analog signal output forom FUNCTION IC Check Soldering.

AM/FM TUNER INPUT

DAB TUNER INPUT iPod Play

M3062LFGPGP Terminal Function

Block Diagram and Pin Configuration (Top View)

Tone Loudness tap

Tone Block Position Input

ZC 1 8 GND Pin Symbol Function

CS 3 6 OUT 4, 5 HV High Voltage input

1 (the RC network consists of Dzc, Rzc1, Rzc2 and Czc as

Case 1 4 5 6 6 6 6 5 4 3 1 shown in typical application circuit) before it is applied

detected zero-crossing to the switch-on of the main 3.3.2 Switch-off Determination

Figure 5 Maximum current limit versus MOSFET maximum on time

3.5 Protection Functions

VCC Overvoltage Auto Restart Mode

4.1 Absolute Maximum Ratings

Parameter Symbol Limit Values Unit Remarks

4.2 Operating Range

Parameter Symbol Limit Values Unit Remarks