Samsung ck6202x3s, ck6202x3x Chassis S51a Service Manual PDF

COLOR TELEVISION RECEIVER
Chassis :
Model:
COLOR TELEVISION RECEIVER
S51A
CK6202X3S/NWT
CK6202X3X/BWT
CONTENTS
1. Precautions
2. Specifications and IC Data
3. Disassembly and Reassembly
4. Alignment and Adjustment
5. Troubleshooting
6. Exploded View and Parts List
7. Electric Parts List
8. Block Diagram
9. PCB Layout Diagram
10. Wiring Diagram
11. Schematic Diagrams
ELECTRONICS
Samsung Electronics Co., Ltd. FEB.1999

Printed in Korea
3S51A-0205
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.
1-1 Safety Precautions

1. Be sure that all of the built-in protective
devices are replaced. Restore any missing
protective shields.
2. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control knobs
and compartment covers.
3. Make sure that there are no cabinet openings
through which peopleparticularly
childrenmight insert fingers and contact
dangerous voltages. Such openings include
the spacing between the picture tube and the
cabinet mask, excessively wide cabinet
ventilation slots, and improperly fitted back
covers.
If the measured resistance is less than 1.0
megohm or greater than 5.2 megohms, an
abnormality exists that must be corrected
before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):
Warning: Do not use an isolation
transformer during this test. Use a leakagecurrent tester or a metering system that
complies with American National Standards
Institute (ANIS C101.1, Leakage Current for
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug
the AC line cord directly into the power
outlet. With the units AC switch first in the
ON position and then OFF, measure the
current between a known earth ground (metal
water pipe, conduit, etc.) and all exposed
metal parts, including: antennas, handle
brackets, metal cabinets, screwheads and
control shafts. The current measured should
not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the
test.
Samsung Electronics
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:
With the units AC plug disconnected from the
AC source, connect an electrical jumper across
the two AC prongs. Connect one lead of the
ohmmeter to an AC prong. Connect the other
lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to prohibit X-ray emissions. To ensure continued
X-ray protection, replace the picture tube only
with one that is the same type as the original.
Carefully reinstall the picture tube shields and
mounting hardware; these also provide X-ray
protection.
8. High Voltage Limits:
High voltage must be measured each time servicing is done on the B+, horizontal deflection
or high voltage circuits. Correct operation of
the X-ray protection circuits must be
reconfirmed whenever they are serviced.
(X-ray protection circuits also may be called
horizontal disable or hold-down.)
Heed the high voltage limits. These include
the Xray Protection Specifications Label, and
the Product Safety and X-ray Warning Note on
the service data schematic.
1-1
Precautions
1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or
electrical design of this unit. Example: Do not
add auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also,
any design changes or additions will void the
manufacturers warranty.
11. Hot Chassis Warning:
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only
if the AC power plug is inserted so that the
chassis is connected to the ground side of the
AC source.
To confirm that the AC power plug is inserted
correctly, do the following: Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the
reading is greater than 1.0V, remove the AC
power plug, reverse its polarity and reinsert.
Re-measure the voltage between the chassis
and ground.
12. Some TV chassis are designed to operate with
85 volts AC between chassis and ground,
regardless of the AC plug polarity. These units
can be safely serviced only if an isolation
transformer inserted between the receiver and
the power source.
13. Some TV chassis have a secondary ground
system in addition to the main chassis ground.
This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulating material that must not be defeated
or altered.
15. Observe the original lead dress, especially

near the following areas: Antenna wiring,
sharp edges, and especially the AC and high
voltage power supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do
not change the spacing between components
and the printed circuit board. Check the AC
power cord for damage. Make sure that leads
and components do not touch thermally hot
parts.
16. Picture Tube Implosion Warning:
The picture tube in this receiver employs
integral implosion protection. To ensure
continued implosion protection, make sure
that the replacement picture tube is the same
as the original.
17. Do not remove, install or handle the picture
tube without first putting on shatterproof
goggles equipped with side shields. Never
handle the picture tube by its neck. Some
in-line picture tubes are equipped with a
permanently attached deflection yoke; do not
try to remove such permanently attached
yokes from the picture tube.
18. Product Safety Notice:
Some electrical and mechanical parts have
special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they
give might be lost if the replacement component differs from the originaleven if the
replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
(
) or ( ! ).
Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications.
A replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
14. Components, parts and wiring that appear to

have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or overheating, and correct any potential hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions

Warning1: First read the Safety Precautions section of this manual. If some unforeseen circumstance creates a conflict between
the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the
cabinet. Follow them.
2. Always unplug the units AC power cord from
the AC power source before attempting to: (a)
Remove or reinstall any component or
assembly, (b) Disconnect an electrical plug or
connector, (c) Connect a test component in
parallel with an electrolytic capacitor.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or
tape is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around
the serviced part has not been damaged.
Samsung Electronics
5. Check the insulation between the blades of the

AC plug and accessible conductive parts
(examples: metal panels, input terminals and
earphone jacks).
6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the
power switch ON. Connect an insulation
resistance meter (500V) to the blades of the AC
plug.
The insulation resistance between each blade
of the AC plug and accessible conductive parts
(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
its assemblies) unless all solid-state heat sinks
are correctly installed.
8. Always connect a test instruments ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instruments ground lead last.
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (solid state) devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect
transistors. The following techniques will
reduce the occurrence of component damage
caused by static electricity.
2. Immediately before handling any semicon
ductor components or assemblies, drain the
electrostatic charge from your body by
touching a known earth ground. Alternatively,
wear a discharging wrist-strap device. (Be
sure to remove it prior to applying power
this is an electric shock precaution.)
3. After removing an ESD-equipped assembly,
place it on a conductive surface such as
aluminum foil to prevent accumulation of
electrostatic charge.
4. Do not use freon-propelled chemicals. These
can generate electrical charges that damage
ESDs.
1-4
5. Use only a grounded-tip soldering iron when

soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
anti-static; these can accumulate sufficient
electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its
protective package until you are ready to
install it. Most replacement ESDs are
packaged with leads that are electrically
shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
9. Minimize body motions when handling
unpackaged replacement ESDs. Motions such
as brushing clothes together, or lifting a foot
from a carpeted floor can generate enough
static electricity to damage an ESD.
Samsung Electronics
Specifications and IC Data
2. Specifications and IC Data

2-1 Specifications
T e le v is io n S y s te m :
C han n e ls :
MO D E L
SYSTEM
S YS T E M
CI
P AL -I (U H F )
CII
P AL -I (V H F /U H F )
CX
P AL -B /G ,S E C AM-B/G
CK
P AL -B /G ,D /K,S E C AM-B /G ,D /K
CB
P AL -B /G
CF
SECAM-L/L' , PAL/SECAM-B/G
PAL/SE CAM
-B/G,I
PAL/SE CAM
-D/K
SECAM-K1,
PAL-D
VHF
2-12
1-13
2-9
UHF
21-69
21-69
13-57
PAL/SECAM
-B/G
PAL/SECAM
-D/K,K1
P AL-I
SECAM-L
SECAM-L'
P icture IF Carrier
38.90
38.90
38.90
38.90
34.50
Sound IF Carrier
33.40
32.40
32.90
34.40
41.00
Color Sub Carrier
34.47
34.47
34.47
34.47
38.93
BAND
In ter m e diate-F r equ en c ies (MH z ):

SYSTEM
BAND
P ic tu r e T ub e:
21 Inch
A51EER131X31
25 Inch
A59EAK071X01 (Normal)
A59EAK552X21 (Invar)
A66EAK071X01 (Normal)
A66EAK552X21 (Invar)
28 Inch
30 Inch
Quick start, in-line-gun,

Black stripe, 90 degree deflection
A70QBZ791X
P o w er R e qu ir e m en ts: AC 230 V, 50Hz or AC 220 ~ 240 V, 50Hz

An tenn a In p u t Im ped an c e :
V H F ,U H F : T ele s c op ic dip o le ante nn a (75 W u nb alanc ed ty pe )
Sp ea k er Im p ed anc e : 8 W , 1 0W + 10 W or 16 W , 5W + 5W (533C only)
Samsung Electronics
2-1
2-2 IC Line Up
LOC NO
NO
Specification
Description
HIC 101
P AP 103T
IF P R E-AMP
IC 201
TDA8844
PAL/SEC AM/NTSC /SE CAM-L
TDA8843
P AL /NTSC
IC 301
LA7845
VE R TIC AL DEF LE CTION AMP
IC 501
TDA6108
R GB DR IVE AMP
IC 601
TDA7297
SOUND AMP(10W/C H)
TDA7266S
SOUND AMP (5W/C H)
IC 701
TDA9859
AUDIO PR OC ESSOR
IC 801
KA3S1265R
SMP S IC (12A)
IC 802
PC 123Y
P HOTO C OUP LE R
IC 803
78R 05
SWITC HING R EGULATOR
IC 804
10
KA7630
SWITC HING R EGULATOR (5,8V)
IC 901
11
SPM171EE
MICOM
IC 902
12
24W16
EE P ROM
IC E01
13
4558
EW DRIVE AMP
IC N01
14
TDA9814T
IC N02
15
TDA9874H
NICAM DE MODULATOR
IC A01
16
L A7567N
SIF DETEC TOR
IC A02
17
TDA9873H
A2 DEMODULATOR
A2 STE R EO
MODUL E
ICM01
18
LA7566
SIF & FM DE TE C TOR
MONO
IC S01
19
TEA5114
VIDE O SWITCH
RGB -S/W
2-2
SIF DETEC TOR (SECAM-L)
R emarks
16K
NIC AM
MODUL E
Samsung Electronics
2-3 Semiconductor Base Diagrams

ELECTROLYTICCONDENSER
IC
DIODE
TDA884X(Pin 56)
SPM171EX(Pin 52)
24W16(Pin 8)
TDA9859(Pin 32)
TRANSISTOR
TRANSISTOR
2SD1651
2SD1650
KSD5072
KSD5071
KSD1711
SAW-FILTER
IC
G1962
K2950M
K9253M
G3956M
UPC574J
or
KA33V
KSA815-Y
KSA539-Y
E B C
IC
TRANSISTOR
TRANSISTOR
KA7630
KSR1012
KSR1010
KSR2010
KA7812
IN
OUT
E C B
Fig. 2-1 Semiconductor Base Diagrams
Samsung Electronics
2-3
MEMO
2-4
Samsung Electronics
Disassembly and reassembly
3. Disassembly and Reassembly

3-1 Back Cover Removal
1. After removing the 7 screws, pull the cabinet backwards.
Samsung Electronics
3-1
3-2 Main Board Removal

3
1
2
11
4
13
5
7
12
6
9
10
1. Separate the TBC-wire 2P connector from GT501,GT502.

2. Separate the CRT Assembly from the CRT socket.
3. Remove the Anode Cap from the CRT.
4. Separate the D-Coil Connector from CN802.
5. Separate the AC cord from CN801.
6. Separate the DC connector from CN401.
7. Separate the CN501B 8P CRT connector from CN501.
8. Separate the CNA05 5P A/V side connector from CN602.
9. Separate the CNA01 8P CRT connector from CN701.
10. Separate the Focus Screen Wire from the FBT clamper.
11. Separate the TBC wire 2P, speaker wires from the wire clamper.
12. Separate the CN701, CN602 connector from the wire clamper.
13. Separate the AC cord from the wire clamper.
14. Remove the main board by pulling it with both hands.
3-2
Samsung Electronics
3-3 Speaker Removal

1. Remove the speaker by
pressing the tension rib.
1. Separate the speaker wires from D-coil

(located on the bottom to the right side).
7
Samsung Electronics
2. Remove the screws.
3-3
3-4 CRT Removal
1. Remove the 4 nuts that mount the CRT to the front cabinet.
Pull the CRT backwards.
2. Caution: Because of the high vacuum and large surface area of the picture
tube, be careful while handling it: (1) Always lift the picture tube by
grasping it firmly around the faceplate, (2) Never lift the tube by its neck.
(3) Do not scratch the picture tube or apply excessive pressure. Fractures
of the glass may cause an implosion.
3-4
Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments

4-1 Preadjustment
4-1-1 Factory Mode
4-1-3 When CRT Is Replaced
1. Do not attempt these adjustments in the Video

Mode.
1. Make the following adjustments AFTER setting up after setting up purity and convergence :
2. The Factory Mode adjustments are necessary

when either the EEPROM (IC902) or the CRT
is replaced.
White Balance
Sub-Brightness, Sub-Contrast
Vertical Center
Vertical Size
Horizontal Size
Fail Safe (This adjustment must be the last
step).
3. Do not tamper with the Adjustment screen

of the Factory Mode menu. This screen is
intended only for factory use.
4-1-2 When EEPROM (IC902) Is Replaced

1. When IC902 is replaced all adjustment data
revert to initial values. It is necessary to
re-program this data.
2. After IC902 is replaced, warm up the TV for
10 seconds.
4-2 Factory/Service Mode

4. Selection sequences for the PAL system:
4-2-1 Procedure for the Adjustment Mode

DOWN or UP key:
1. This mode uses the standard remote control.
The Service Mode is activated by entering the
following remote-control sequence :
AGCVCOSBTSCTSCRSCRG
BGCDLSTTLCOVOLPSLPVS
PVAPHSPEWPEPPECPETVSC
TSCSAQEWPCTPTTPHMPVP
PHPNSRPDLAGC.
(1) STAND-BY DISPLAY MENU MUTE

POWER ON.
2. The SERVICE (FACTORY) message will be
displayed. The Service Mode has three components: Adjustment, Option and Reset.
3. Access the Adjustment Mode by pressing the
VOLUME keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the
CHANNEL keys ( ,).
Samsung Electronics
5. The VOLUME keys increase or decrease the

adjustment values (stored in the
non-volatile memory) when Adjustment Mode
is cancelled.
6. Cancel the Adjustment Mode by re-pressing
the HIDDEN or Power OFF/ON keys.
7.
After adjustments are completed, re-start

the TV set.
4-1
4-2-2 Main Adjustment Parameters

OSD
FUNCTION
RANGE
AGC
AUTO GAIN CONTROL
0 - 63
VCO
VOLTAGE CONTROLLED OSCILLATOR
0 - 127
SBT
SUB BRIGHTNESS
0 - 23
SCT
SUB CONTRAST
0 - 23
SCR
SUB COLOUR
0 - 23
SC
S-CORRECTION
0 - 63
RG
RED DRIVE GAIN
0 - 63
BG
BLUE DRIVE GAIN
0 - 63
CDL
CATHODE DRIVE LEVEL
0-7
STT
SUB TINT ( FOR NTSC )
0-7
LCO
SECAM-L VOLTAGE CONTROLLED OSCILLATOR
0-1
VOL
VOLUME INITIAL LEVEL
0 - 63
PSL
PAL VERTICAL SLOPE
0 - 63
PVS
PAL VERTICAL SHIFT
0 - 63
PVA
PAL VERTICAL AMPLITUDE
0 - 63
PHS
PAL HORIZONTAL SHIFT
0 - 63
PEW
PAL E-W WIDTH
0 - 63
PEP
PAL E-W PALABOLA
0 - 63
PEC
PAL E-W CORNER
0 - 63
PET
PAL E-W TRAPEZIUM
0 - 63
VSC
VERTICAL SCROLL
0 - 63
TSC
TELETEXT SUB CONTRAST
0 - 63
SA
SEPARATION ADJUSTMENT (STEREO)
0 - 15
QEW
Q(12.8:9) MODEL E-W WIDTH
0-7
PCT
PIP CONTRAST
0 - 15
PTT
PIP TINT
0 - 63
PHM
PIP HORIZONTAL MOVE
0 - 15
PVP
PIP VERTICAL POSITION
0 - 63
PHP
PIP HORIZONTAL POSITION
0 - 63
NSR
NTSC SUB COLOUR
0 - 23
PDL
PAL DELAYTIME
0 - 15
4-2
Samsung Electronics
FACTORY MODE VALUE

OSD
INITIAL
2 (CH)
OSD
INITIAL
OSD
INITIAL
LCO
1 (FIXED)
TSC
20(FIXED)
AGC
10
VOL
25
SA
VCO
80(FIXED)
PSL
31(FIXED)
QEW
SBT
PVS
31
PCT
7(FIXED)
SCT
16
PVA
31
PTT
31(FIXED)
SCR
5(FIXED)
PHS
40
PHM
8(FIXED)
SC
11(FIXED)
PEW
38
PVP
31(FIXED)
RG
31
PEP
22
PHP
31(FIXED)
BG
31
PEC
22
NSR
3 (FIXED)
CDL
PET
30
PDL
0 (FIXED)
STT
10(FIXED)
VSC
31(FIXED)
4-2-3 AGING Mode (Reference Only)

This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the factory by
twice pressing the FACTORY key.
Even if the TV power is cut off, the Aging Mode is not cancelled, The AGING mode is cancelled by
repressing the HIDDEN or any key on the front pannel.
Samsung Electronics
4-3
4-2-4 Option Byte Table

Option Byte
1.ZOOM MODE : NORMAL/ZOOM/16:9
2.AUDIO MODE : NICAM STEREO
3.ONE CHIP : TDA8844
4.LED OPTION : NORMAL
5.LANGUAGE : WEST
ENG/GER/FRA/DUT/SPA/ITA/SWE
6.SYSTEM: CX
7.ATS OPTION : ON
8.FIELD POL : FIELD POS
OPTION
ZOOM MODE
AUDIO MODE
ONECHIP
LED OPTION
LANGUAGE
SYSTEM
ATS OPTION
FIELD POL
4-4
OSD
NOTE
PLU/NOR/ZOOM/16:9
12.8 : 9 CRT USED(30",22")
NORMAL/ZOOM/16:9
NORMAL CRT USED
NORMAL/ZOOM
PLUS/NORMAL
12.8 : 9 CRT USED(26")
NICAM STEREO
NICAM MODULE USED
STEREO
A2 MODULE USED
LINE STEREO
MONO MODULE USED

(LINE STEREO MODEL )
MONO
MONO MODULE USED

(MONO MODEL )
TDA8844
CRT(MORE THAN 22-INCH)USED
TDA8842
CRT(MORE THAN 21-INCH)USED
NORMAL
DEFAULT
POLAND
POLAND MODEL ONLY
WEST
ENG/GER/FRA/DUT/SPA/
ITA/SWE
WEST EUROPE MARKET

ENGLISH/GERMANY/FRANCE/
NETHERLANDS/SPAIN/ITALY/SWEDEN
EAST
ENG/CZE/CRO/RUM/HUN/
POL
EAST EUROPE MARKET

ENGLISH/CZECH/CROATIA/ROMANIA/
HUNGARY/POLAND
CF
SECAM-L/L', PAL/SECAM-B/G
CI
PAL - I ( UHF BAND ONLY)
CK
PAL/SECAM - B/G,D/K
CX
PAL/SECAM -B/G
CB
PAL -B/G
ON
ATM FUNCTION USED
OFF
ATM FUNCTION NOT USED
FIELD POS
PHILIPS CRT USED
FIELD NEG
OTHER CRT USED
Samsung Electronics
4-2-5 RESET
The Reset Mode is used during factory inspection.
Function Reset:
1.
2.
3.
Channels
Language
Station name
Add/Erase
Last condition
Clear
4-3 Other Adjustments

4-3-1 General
1. Usually, a color TV needs only slight touchup adjustment upon installation. Check the
basic characteristics such as height, horizontal
and vertical sync and focus.
2. The picture should have good black and white
details. There should be no objectionable
color shading; if color shading is present, perform the purity and convergence adjustments
described below.
3. Use the specified test equipment or its equivalent.
4. Correct impedance matching is essential.
5. Avoid overload. Excessive signal from a sweep
generator might overload the front-end of the
TV. When inserting signal markers, do not
allow the marker generator to distort test
results.
4-3-2 Automatic Degaussing

A degaussing coil is mounted around the picture tube, so that external degaussing after
moving the TV should be unnecessary. But
the receiver must be properly degaussed upon
installation.
The degaussing coil operates for about 1 second after the power is switched ON. If the set
has been moved or turned in a different direction, disconnect its AC power for at least 30
minutes.
If the chassis or parts of the cabinet become
magnetized, poor color purity will result. If
this happens, use an external degaussing coil.
Slowly move the degaussing coil around the
faceplate of the picture tube and the sides and
front of the receiver. Slowly withdraw the coil
to a distance of about 6 feet before removing
power.
6. Connect the TV only to an AC power source

with voltage and frequency as specified on the
backcover nameplate.
7. Do not attempt to connect or disconnect any
wires while the TV is turned on. Make sure
that the power cord is disconnected before
replacing any parts.
8. To protect against shock hazard, use an isolation transformer.
Samsung Electronics
4-5
4-3-3 High Voltage Check
4-3-6 Purity Adjustment
CAUTION: There is no high voltage adjustment on this chassis.

The B+ power supply must be set to +155 volts (Full color bar input
and normal picture level).
1. Warm up the receiver for at least 20 minutes.
1. Connect a digital voltmeter to the second

anode of the picture tube.
2. Plug in the CRT deflection yoke and tighten

the clamp screw.
3. Plug the convergence yoke into the CRT and
set in as shown in Fig. 4-2.
2. Turn on the TV. Set the Brightness and

Contrast controls to minimum (zero beam current).
4. Input a black and white signal.
3. The high voltage should not exceed 33KV.
5. Fully demagnetize the receiver by applying an

external degaussing coil.
4. Adjust the Brightness and contrast controls to

both extremes. Ensure that the high voltage
does not exceed 33KV under any conditions.
6. Turn the CONTRAST and BRIGHTNESS controls to maximum.
4-3-4 FOCUS Adjustment
7. Loosen the clamp screw holding the yoke.

Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-3).
1. Input a black and white signal.

2. Adjust the tuning control for the clearest
picture.
3. Adjust the FOCUS control for well defined
scanning lines in the center area of the screen.
4-3-5 Screen Adjustment

1. Connect CRT socket pin GK, BK, RK to an
oscilloscope probe.
8. Tighten the convergence yoke.

9. Slowly move the deflection yoke forward,
and adjust for the best overall green screen.
10. Temporarily tighten the deflection yoke.
11. Produce blue and red rasters by adjusting the
low-light controls. Check for good purity in
each field.
12. Tighten the deflection yoke.
2. Input a gray scale pattern. (Use a pattern

generator, PM5518)
3. Use the Picture mode for the STANDARD picture.
4. Adjust the Screen VR (on the FBT) so that the
_
voltage on the oscilloscope becomes 140+2.5V
(See Fig. 4-1).
140 +_ 2.5V
GND
Fig. 4-1
4-6
Samsung Electronics
4 Pole Magnet
2 Pole Magnet
6 Pole Magnet
2 POLE
PURITY
Clamper
Screw
YOKE
CLAMP
SCREW
6 POLE
CONVERGENCE
4 POLE
CONVERGENCE
Fig. 4-2 Convergence Magnet Assembly
Vertical Green Belt
31m/m
Fig. 4-3 Center Convergence Adjustment
4-3-7 White Balance Adjustment

(a) Set up
1. Warm up the TV for at least 30 minutes in the

White Pattern.
2. Input a Toshiba pattern.
(b) High-Light Adjustment
Set SCT to 40 5 fL in the Factory Service

Mode with using CA100. (See Fig. 4-4 )
(c) Low-Light Adjustment
Fig. 4-4
Samsung Electronics
Set SBT to 1.5 0.2 fL in the Factory Service

Mode with using CA100. (See Fig. 4-4 )
4-7
4-3-8 Center Convergence Adjustment

1. Warm up the receiver for at least 20 minutes.
2. Adjust the two tabs of the 4 pole magnets to
change the angle between them. Superimpose
the red and blue vertical lines in the center
area of the screen.
3. Adjust the Brightness and Contrast controls
for a well defined picture.
4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them.
Superimpose the red and the blue vertical
lines in the center area of the screen.
BLUE
5. Turn the both tabs at the same time, keeping

the angle constant, and superimpose the red
and blue horizontal line in the center of the
screen.
6. Adjust the two-tab pairs of the 6-pole magnets
to superimpose the red and blue line onto the
green. (Changing the angle affects the vertical
lines, and rotating both magnets affects the
horizontal lines.)
7. Repeat adjustments 2~6, if necessary.
8. Since the 4-pole magnets and 6-pole magnets
interact, the dot movement is complex
(Fig. 4-5).
RED/BLUE
RED
BLUE
RED/BLUE
RED
GREEN
GREEN
6-Pole Magnet Movement
4-Pole Magnet Movement
Fig. 4-5 Center Convergence Adjustment
4-3-9 RF AGC Adjustment

1. Tune to the strongest local station.
2. Enter the Factory Service Mode to make adjustments.
3. Adjust the AGC control untill noise(snow) disappears from the screen.
4-8
Samsung Electronics
4-3-10 Geometry Adjustment

1. Input a lion head pattern.
2. Adjus t PVS s o that the pic ture is vertically centered.
3. Adjus t with PVA s o that the top and bottom margins of the pic ture are 4.
4. Adjus t PHS s o that the pic ture is horizontally centered.
5. Adjus t with PEW s o that the left and right margins of the picture are 5.
4
5
4
6. Input a crosshatch pattern.

7. Adjus t PEP, PEC , PET for vertical linearity.
Samsung Electronics
4-9
Troubleshooting
5. Troubleshooting
5-1 No Video (Raster On, No Sound)
Measure the
Voltage of each of, 8 pins
of TU101
No
Check/Replace
TU101, HC101
No
Check/Replace
IC901,IC201,IC902 ,IC701,
Audio Module
Yes
Check IC901
Pins 39, 40
Yes
See "No Video"

(Sound OK)
Samsung Electronics
See "No Sound"

(Video OK)
5-1
Troubleshooting
5-2 No Power
Check the 130V,

12.7V B+ Lines
No
Check/Replace
IC801, D802
Yes
Check IC804
Pin 9 (5V)
No
Check/Replace
IC804(KA7630),DZ905,DZ804
No
Check/Replace
IC901
No
Check/Replace
IC901(m-com)
No
Check/Replace
IC201, Q402, Q403
No
Check/Replace
DZ805, IC802
Yes
Check IC901
Pin 8 (4V).
Yes
Check IC901
Pin 18 ; Stand-by : 0V
Normal : 5V
Yes
Check IC201,
Pin 40 (H-out)
Yes
Check Q402, Q403
5-2
Samsung Electronics
Troubleshooting
5-3 No Video (Sound OK)
Check IC201
Pin 12,37 (8V)
No
Check/Replace
IC804 KA7630
No
Check/Replace
IC201
Yes
Check IC201
Pin 6 (CVBS)
2Vp-p
Yes
Check IC201
Pins 19, 20, 21
(R/G/B-OUT)
No
Yes
Check IC202
pin 27 (Y-IN)
No
Check/Replace
IC201,D205,DZ204
No
Check/Replace
IC501
Yes
Check IC501,
on the CRT PCB
Yes
Check/Replace
R505 (HEATER 6.3Vrms)
CRT, V999
Samsung Electronics
5-3
Troubleshooting
5-4 No Sound (Video OK)
CHECK IC701
Pin 3,5
No
CHECK/REPLACE
Sound Module (MD701)
No
CHECK/REPLACE
IC701, C712, C719
No
CHECK/REPLACE
IC601, R601, R602
Yes
CHECK IC701
Pin 15,18
Yes
CHECK IC601 Pin

1 2 14 15
Sound output
Yes
CHECK/REPLACE
A/V Front Assembly.
5-5 Power OFF/ON (Repeatedly)

CHECK Q403
COLLECTOR H-PULSE
NO
SEE " NO-POWER"
YES
CHE CK IC901
PIN26(H-SYNC )
NO
CHE CK/REPLACE
IC901,Q907,C913
DZ402
YES
CHE CK IC301
PIN7(V-BLANK)
YES
CHE CK/REPLACE
Q301,Q302,D304
NO
CHECK PIN6(+16.5V)
PIN1(-14V)
NO
CHE CK/REPLACE
R409,R413,D407,D410
DZ302,DZ303
YES
CHECK/RE PLACE
IC301,IC201
5-4
Samsung Electronics
Troubleshooting
5-6 SMPS (Power Supply) Does Not Function

(1) W he n F 802 is op en :
C he ck/Replace F 8 02 , IC 80 1 , D 80 2.
(2) W he n F 802 is okay, but SMP S doe s n ot fu nction:
C he ck/Replace D Z80 1 , D Z8 08 , IC 80 2 , D Z8 05 .
(3) O the rs: S ee "5. Tro ublesh ooting"
Samsung Electronics
5-5
Exploded View & Parts List
6. Exploded View & Parts List

6-1 CK6202X3X/BWT
No
1
Code No
Specification
Qty
-,CK6202SXR,S1000 MLB TVI BWT,HB

,CK6202SXR,S1000 MLB BWT TVI,HIPS,HB
-,6202,S1300,PS,T0.4,-,-,62.7202,S1000,HIPS,HB,BLK,-,
6202,MW,PS,T0.3,BLK,-,AL,SS R2000 25,SILVER,L60,-,-,
-,-,-,KIFUCO LA701,-,62.7202,-,ABS,HB,BLK
-,SUS304,0.6,OD12.2,H13,N4,-,-,566B~569B,S51A,PAL,-,RH,+,M4,L12,ZPC(YEL),-,OD14
-,62.7202,-,ABS,HB,BLK
RH,+,2,M4,L15,ZPC(BLK),SWRCH18
-,62.7202,-,ACRYL,-,-,-,62.7202,LG41338,ABS,HB,-,ROUND,RED/GRN,5.0mm,630/565nm
-,SCT12B,-,RH,+,M3,L6,ZPC(YEL),SM20C,ERH,+,M3,L6,ZPC(YEL),SM20C,-
1
1
2
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
2
6002-000522
AA91-60003A
ASSY-CABINET,FRONT
CABINET-FRONTGRILLE-SHEET
DOOR-CONTROL
INLAY-CONTROL
BADGE-BRAND
LATCH-DOOR
KNOB-POWER,M
SPRING-CS
ASSY-PCB,A/V SIDE
SCREW-TAPPING
KNOB-CONTROL
SCREW-TAPPING
INDICATOR-LED
WINDOW-REMOCON
LED
ASSY-PCB,CONTROL
SCREW-MACHINE
SCREW-MACHIN
ASSY-HOLDER,SPK OPTION
SCREW-TAPPING
ASSY-HOLDER,SPK
TH,+,2,M4,L15,ZPC(BLK),SWRCH18
-,PP,-,-,8ohm 10W,CT2199
8
1
2
2-1
2-2
2-3
2-4
2-5
AA03-10023R
AA63-60004P
AA60-10050Q
AA65-30113A
AA27-20004G
3704-001105
CRT-COLOR
SPACER-GUM,CRT
SCREW-ASSY
CLAMP-D,COIL
COIL-DEGAUSSING
SOCKET-CRT
-,A59KPR84X01(DB),+500mG,25,1
NTR RUBBER,T2,GRY,-,-,WC,HH,+,M5,L26.5,SWRCH18A,ZPC(
NYLON 66,V2,BLK,TVI 25~29,-,-,25,16.9ohm,35T,L2600,E
11P,20PI,26.5PI,NI,-
1
4
4
4
1
1
3
3-1
3-2
3-3
AA64-30641D
AA60-10050T
AA64-60052C
6002-000512
CABINET-BACK
SCREW-TAPPING
INLAY-BACK
SCREW-TAPPING
-,6202,-,HIPS,V2,BLK,-,RH,+,2S,M4,L20,ZPC(BLK),SWRCH1
-,S51A SCART(2),PS,T0.5,BLK,-,RH,+,2,M4,L12,ZPC(BLK),SWRCH18
1
7
1
1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
AA91-00067A
AA64-31156H
AA63-50064A
AA64-50111A
AA64-60274D
AA64-70011B
AA61-30001A
AA64-10166A
AA61-60005K
AA95-00004A
AA60-10002A
AA64-10058A
6002-000514
AA64-40238A
AA64-40060A
0601-000198
AA95-30002B
6001-000677
6001-000677
Description
Samsung Electronics
Remark
6-1
Electric Parts List
7. Electric Parts List
7-1 CK6202X3S/NWT (CK6202X3X AND CK6202X3S Dissimilar Parts)

Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
ASSY-PCB,MAIN(OPT)
AA94-00485AASSY-PCB,MAIN(OPT);CK6202X3S/NWT,S51A,N-RUSSIA,-
AA68-00044AMANUAL-USERS;S51A,N-RUS,-,B5,W/P100(G),-
ASSY-PCB,A/V FRONT
*
ASSY-CABINET;6202,CK6202X3S/NWT
AA95-00031AASSY-PCB,A/V FRONT;DP,22,77,02,3399,S51A,-,-,-
ASSY-PCB,CONTROL
*
Remark
ASSY-ACCESSORY
BUYER : SRSC
*
*
CB+21
CB+CF
PA+CF
PC+CF
AA95-00113AASSY-PCB,CONTROL;DP,S51A,02
AA91-10287HASSY-CABINET,FRONT;DP,CK6202SXR,S1000 MLB NWT TVI

AA64-31156GCABINET-FRONT;-,CK6202SXR,S1000 MLB NWT TVI,HIPS,H
6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWRCH18
6003-001024 SCREW-TAPTITE;RWH,+,B,M4,L12,ZPC(YEL),SWRCH1
ASSY-CRT
AA03-10016NCRT-COLOR;-,A59KPR84X01(DB),+380mG,25,1
7-2 CK6202X3X/BWT Parts List

Loc. No.
Code No.
Remark
ASSY-PCB,MAIN(OPT)
BUYER : SRSC
*
AA94-00488AASSY-PCB,MAIN(OPT);CK6202X3X/BWT,S51A,CIS,-
C102
C103
C104
C105
C106
C107
C109
C207
C210
C211
C213
C214
C215
C216
C217
C218
C219
C220
C221
C222
C223
C224
C225
C226
C227
C228
C229
C230
C231
2401-002594
2202-002037
2202-002037
2202-002037
2401-001082
2401-000914
2202-000796
2401-001026
2306-000122
2401-002619
2301-000224
2401-000660
2305-000412
2401-001840
2305-000665
2305-000411
2401-002144
2401-000302
2305-000289
2305-000412
2202-002037
2202-002037
2202-002037
2401-000480
2201-000986
2201-000273
2301-000356
2301-000192
2202-000183
Samsung Electronics
C-AL;220uF,20%,16V,GP,TP,8x11.5,5
C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3.
C-AL;330nF,20%,50V,GP,TP,5x11,5
C-AL;22uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,C-AL;3.3UF,20%,50V,GP,TP,5X11,5
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm,
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,DISC;12pF,5%,50V,NPO,TP,5x3mm,2.5mm
C-CERAMIC,DISC;18pF,5%,50V,CH,TP,5x3mm,5
C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm
C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP,3.5X1.9MM,
Loc. No.
C232
C233
C234
C235
C236
C237
C238
C239
C240
C241
C242
C243
C244
C245
C301
C302
C303
C304
C305
C306
C307
C308
C309
C403
C404
C405
C406
C407
C408
C409
C410
C411
C412
C413
Code No.
2202-000796
2309-000138
2305-000289
2202-000849
2202-002037
2305-000665
2301-000383
2301-000445
2401-001840
2401-000603
2202-000183
2401-000603
2301-000224
2305-000665
2301-000254
2401-000360
2201-000259
2305-000285
2305-001011
2305-000149
2401-000360
2401-000480
2401-001840
2401-000901
2201-000291
2401-002268
2306-000272
2201-000984
2305-000382
2201-000551
2401-001397
2305-000178
2201-000599
2401-000302
Remark
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,C-FILM,PE-PPF;100nF,5%,50V,TP,20x16x8.5,7.5m
C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3.5x1.9,C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3.
C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP,3.5X1.9MM,
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-FILM,PEF;39nF,5%,50V,TP,7.5x3.5x6.5mm,5
C-AL;100uF,20%,50V,GP,TP,8x11.5,5
C-CERAMIC,DISC;180pF,10%,500V,Y5P,TP,6x4,5
C-FILM,MPEF;220NF,5%,100V,TP,10.5X5.5X15MM,5
C-FILM,MPEF;22nF,5%,100V,TP,3.5x12.5x7.5mm
C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5,5
C-AL;100uF,20%,50V,GP,TP,8x11.5,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;22uF,20%,160V,GP,TP,10x20,5
C-CERAMIC,DISC;1nF,10%,500V,Y5P,TP,8.5x5MM,5
C-AL;2.2uF,20%,250V,LZ,TP,8X11,5
C-FILM,MPPF;820nF,5%,400V,BK,29x25.5x18.5,
C-CERAMIC,DISC;680pF,10%,2KV,Y5P,TP,11x6,7.5m
C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mm
C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5
C-AL;470uF,20%,25V,GP,TP,10x16,5
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
7-1
Electric Parts List
Loc. No.
C414
C415
C416
C417
C418
C419
C421
C422
C423
C424
C425
C427
C504
C506
C510
C520
C530
C601
C602
C603
C604
C605
C606
C607
C701
C702
C703
C705
C707
C709
C710
C711
C712
C713
C714
C715
C716
C717
C718
C719
C720
C721
C722
C723
C725
C727
C730
C731
C732
C733
C801
C802
C804
C805
C806
C807
C808
C809
C811
C812
C813
C814
C815
C816
C817
C818
C819
C820
C821
C822
C823
C824
C825
C826
C827
C828
C829
7-2
Code No.
2306-000329
2306-000322
2301-001258
2306-000102
2201-000556
2401-001397
2401-002619
2306-000122
2201-000556
2401-001527
2305-000154
2201-002041
2202-000862
2301-000213
2401-000430
2401-001232
2201-002063
2401-001914
2301-000445
2401-001333
2301-000192
2401-001914
2301-000445
2401-001998
2202-002037
2401-002144
2202-000243
2305-000289
2401-000302
2306-000122
2401-000302
2401-002235
2401-000480
2301-000247
2301-000289
2401-000647
2401-000647
2301-000289
2301-000247
2401-000480
2401-002235
2301-000175
2305-000289
2301-000175
2305-000289
2305-000289
2202-000231
2202-000231
2202-000231
2202-000231
2306-000321
2306-000321
2201-000332
2201-000332
2401-003031
2303-000163
2401-002292
2301-000224
2301-000310
2201-002002
2201-002002
2201-000683
2401-003026
2401-000293
2201-000599
2401-000722
2201-000599
2401-000722
2301-000192
2201-000599
2401-001840
2305-000289
2306-000122
2401-001840
2401-002235
2401-000493
2401-000302
Remark
C-FILM,MPPF;7nF,3%,1.6KV,TP,28.5x18.5x11mm
C-FILM,MPPF;12nF,5%,1.6KV,TP,29x20.5x13,20
C-FILM,PPF;39nF,5%,400V,TP,19.5x9x15,7.5
C-FILM,MPPF;1.2uF,5%,250V,TP,29*31*14.5,20
C-AL;470uF,20%,25V,GP,TP,10x16,5
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-AL;47uF,20%,250V,HR,TP,13x25mm,5m
C-FILM,MPEF;100nF,5%,400V,TP,21.5x6.5x11.5
C-CERAMIC,DISC;820pF,10%,2KV,Y5P,TP,12x6,7.5m
C-CERAMIC,MLC-AXIAL;390pF,10%,50V,Y5P,TP,3.5x1.9,C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5
C-AL;10uF,20%,250V,GP,TP,10x16mm,5m
C-AL;4.7uF,20%,250V,GP,TP,10x12.5,5
C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,16x5,7
C-AL;1uF,20%,50V,BP,TP,5x11,5
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,BP,TP,5x11,5
C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;33pF,5%,50V,SL,TP,3.5x19,C-FILM,MPEF;220nF,5%,63V,TP,-,5mm
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5
C-AL;2.2uF,20%,50V,BP,TP,5x11,5
C-AL;2.2uF,20%,50V,BP,TP,5x11,5
C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-FILM,MPPF;470NF,5%,275V,TP,-,22.5
C-FILM,MPPF;470NF,5%,275V,TP,-,22.5
C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7
C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7
C-AL;470uF,20%,450V,GP,BK,35x45mm,1
C-FILM,PPF;2.2nF,5%,800V,TP,15x13x8.5,7.5
C-AL;47uF,20%,25V,WT,TP,8X11,5
C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,5
C-CERAMIC,DISC;4700pF,20%,400V,+20%~-55%,TP,2
C-CERAMIC,DISC;4700pF,20%,400V,+20%~-55%,TP,2
C-CERAMIC,DISC;850pF,10%,1KV,Y5P,TP,10x5,5
C-AL;330uF,20%,200V,GP,ST,22x35,10
C-AL;100uF,+30-10%,200V,GP,TP,16x25
C-AL;2200uF,20%,25V,WT,TP,16x25,7.5
C-AL;2200uF,20%,25V,WT,TP,16x25,7.5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
Loc. No.
C830
C831
C832
C833
C835
C901
C902
C903
C904
C905
C906
C907
C908
C909
C910
C911
C913
C914
C915
C916
C917
C918
C919
C920
C921
C923
C924
C925
C926
C927
C928
CE01
CE02
CE03
CN501B
CN602
CN701
CN802
CN901A
CN902
CT01
CT02
CT03
CT04
CT05
CT06
CT07
CT08
CT09
CW701
CW901
D201
D202
D203
D204
D205
D209
D210
D217
D301
D302
D303
D304
D401
D402
D403
D404
D406
D407
D410
D507
D508
D509
D520
D601
D602
D801
Code No.
Remark
2401-000611 C-AL;1uF,20%,50V,WT,TP,5x11,5
2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5
2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
2401-002286 C-AL;470uF,20%,16V,WT,TP,10x12.5,5
2201-000234 C-CERAMIC,DISC;150pF,5%,50V,CH,TP,9.5x3,5
2301-000108 C-FILM,PEF;1.5nF,5%,50V,TP,6.5x3.0x5.5mm,
2201-000119 C-CERAMIC,DISC;100nF,+80-20%,50V,Y5V,TP,8x3.5
2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,
2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3.
2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm
2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
2201-000980 C-CERAMIC,DISC;30pF,5%,50V,CH,TP,5.0x3.0,5mm
2201-000980 C-CERAMIC,DISC;30pF,5%,50V,CH,TP,5.0x3.0,5mm
2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3.
2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5
2401-002597 C-AL;220uF,20%,35V,GP,TP,10x12.5,5
2305-000470 C-FILM,MPEF;68nF,5%,100V,TP,-,5mm
AA39-20604ALEAD CONNECTOR-ASSY;-,YBNH250-09,YBNH05/04,5/4P,5
3711-002644 CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGHT,SN
AA27-20004GCOIL-DEGAUSSING;-,25,16.9ohm,35T,L2600,E
2401-000242 C-AL;100uF,20%,10V,GP,TP,5x11,5
2202-000164 C-CERAMIC,MLC-AXIAL;.18NF,10%,50V,Y5P,TP,3.5X1.9MM,
2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
2301-000235 C-FILM,PEF;3.9nF,5%,50V,TP,6.5x3.0x5.5mm,
2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5
2503-000161 C-NETWORK;330pFx8,20%,50V,MCCB1H331MX8YT
2503-000156 C-NETWORK;100pFx4,20%,50V
0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP
0402-000216 DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-204
0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP
0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TP
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0402-001012 DIODE-RECTIFIER;FMP-3FU,1500V,5A,TO-3PF
0402-000216 DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-204
0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,
0402-000213 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41,TP
Samsung Electronics
Electric Parts List
Loc. No.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
D802
D803
D804
D805
D806
D807
D808
D809
D810
D813
D901
D906
D907
DE01
DT01
DT02
DT05
DV801
DV802
DZ201
DZ202
DZ203
DZ204
DZ205
DZ206
DZ210
DZ302
DZ303
DZ304
DZ305
DZ306
DZ402
DZ403
DZ505
DZ601
DZ602
DZ603
DZ604
DZ701
DZ702
DZ703
DZ704
DZ705
DZ801
DZ802
DZ803
DZ805
DZ807
DZ808
DZ901
DZ904
DZ905
DZT01
F801
F801A
F801B
F802
F803
GT804A
HC101
IC201
IC301
IC501
IC601
IC701
IC801
IC802
IC803
IC804
IC901
IC902
ICE01
J206
JA701
L101
L102
L103
Code No.
Remark
Loc. No.
0402-001160 DIODE-BRIDGE;D5SB60,600V,2.8A,SIP-4,ST
0402-000231 DIODE-RECTIFIER;FMG-G26S,600V,4A,TO-220F,ST
0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
1405-000187 VARISTOR;750V,1250A,12.5x7mm,TP
1405-000187 VARISTOR;750V,1250A,12.5x7mm,TP
0403-000298 DIODE-ZENER;MTZ6.8C,6.8V,6.66-7.01V,500mW,
0403-000659 DIODE-ZENER;MTZ2.0A,2V,1.88-2.10V,500mW,DO
0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,
0403-000494 DIODE-ZENER;MTZ39,39V,35.36-37.2V,500mW,DO
0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TP
0403-000698 DIODE-ZENER;TZP12A,12V,11.4-12.6V,1W,DO-41
1203-001217 IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL,PLASTIC,2
1203-000451 IC-VOLTAGE REGULATOR;33,TO-92,3P,-,PLASTIC,31/35V,2
0403-000355 DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500mW
3601-000281 FUSE-FERRULE;250V,4A,TL,GLASS,5.2x20mm
3602-000114 FUSE-HOLDER;-,-,30mohm
3602-000114 FUSE-HOLDER;-,-,30mohm
3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mm
3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mm
AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,500,1617#22
AA13-20004WIC-HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TP
0904-001294 IC-BUS CONTROLLER;
1204-000517 IC-VERTIVAL DEF.;LA7845,SIP,7P,-,PLASTIC,40V,11
1201-001330 IC-VIDEO AMP;6108,ZSIP,9P,-,SINGLE,-,PLASTI
1201-001064 IC-POWER AMP;7297,ZIP,15P,-,DUAL,32dB,PLAST
1204-000473 IC-AUDIO PROCESSOR;TDA9859,DIP,32P,-,PLASTIC,-,-,
1203-001482 IC-PWM CONTROLLER;3S1265R,TO-3P,5P,210,PLASTIC,6
0604-001038 PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST
1203-001006 IC-VOLTAGE REGULATOR;78R05,TO-220F,4P,-,PLASTIC,4.8
1203-000644 IC-POSI.FIXED REG.;7630,SIP,10P,-,PLASTIC,5.1/8V,
AA13-30021MIC-MCU;-,SAA5291PS-135,8bit,SDIP,CK29
1103-001105 IC-EEPROM;24C040,4Kx1BIT,DIP,8P,300MIL,1
1201-000191 IC-OP AMP;4558,DIP,8P,300MIL,DUAL,20V/mV
3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G
3722-000195 JACK-SCART;42P,-,SN,BLK,NO
2701-000326 INDUCTOR-AXIAL;560nH,10%,2.3x3.4mm
2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L202
L205
L206
L207
L208
L303
L401
L402
L403
L404
L501
L601
L603
L701
L702
L703
L704
L705
L706
L707
L708
L709
L801
L802
L803
L804
L805
L806
L807
L808
L901
L903
L904
L905
L906
L907
LT01
LT02
Q201
Q202
Q204
Q207
Q210
Q301
Q302
! Q401
! Q402
! Q403
Q701
Q702
Q801
Q901
Q902
Q903
Q904
Q905
Q907
Q908
QE01
QT01
QT02
QT03
R201
R202
R203
R204
R212
R214
R215
R218
R219
R220
R221
R222
R223
R224
R225
Samsung Electronics
Code No.
Remark
2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm
AA27-40003HCOIL-HORIZ,WIDTH;-,2mH,DR15x20,2UEW0.35,ST
AA27-30003GCOIL-LINERITY;-,44uH,DR14x15,PI0.2x10,18x33,
AA27-40003L COIL-HORIZ,WIDTH;-,1.0mH,DR14x20,2UEW0.45,ST
2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G
AA29-30002F FILTER-LINE NOISE;-,6mH,2.45A,-,3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G
2901-000299 FILTER-EMI ON BOARD;-,6A,UL/CSA,-,9x7.5,TP,2701-001032 INDUCTOR-AXIAL;100uH,10%,5x14mm
2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G
2701-000189 INDUCTOR-AXIAL;470nH,10%,2.5x3.4mm
2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm
2901-000299 FILTER-EMI ON BOARD;-,6A,UL/CSA,-,9x7.5,TP,2901-000299 FILTER-EMI ON BOARD;-,6A,UL/CSA,-,9x7.5,TP,0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200502-000298 TR-POWER;KSD73,NPN,30W,TO-220,-,120-240
0502-001007 TR-POWER;KSC2073-H2,NPN,25W,TO-220,ST,6
0502-001136 TR-POWER;KSD5703,NPN,70W,TO-3PF,ST,80501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,-,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP
0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP
0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP
0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200504-000125 TR-DIGITAL;KSR1012,NPN,300mW,47K,TO-92,TP
0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1202001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP,2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,2001-000343 R-CARBON;130OHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm
2001-000617 R-CARBON;3.9MOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-001026 R-CARBON;910OHM,5%,1/8W,AA,TP,-
7-3
Electric Parts List
Loc. No.
R226
R230
R233
R234
R235
R237
R238
R239
R240
R241
R243
R246
R247
R248
R249
R250
R251
R252
R253
R255
R256
R257
R258
R259
R260
R261
R262
R301
R302
R303
R304
R305
R306
R308
R309
R310
R311
R312
R313
R314
R315
R316
R317
R404
R405
R406
R407
R409
R410
R411
R412
R413
R414
R415
R417
R418
R419
R420
R421
R422
R424
R425
R428
R429
R430
R501
R502
R503
R505
R506
R507
R508
R509
R510
R517
R518
R519
7-4
Code No.
2001-000793
2001-000331
2001-000780
2001-000780
2001-000780
2001-000007
2001-001110
2001-000008
2001-001125
2001-000429
2001-000232
2001-000273
2001-000281
2001-000793
2001-000429
2001-000938
2001-000281
2001-000563
2001-000591
2001-000008
2004-001234
2001-000563
2004-001914
2001-000281
2001-001015
2001-000331
2001-001015
2001-001045
2001-001049
2001-000016
2008-000254
2003-002069
2003-002069
2003-002069
2001-000290
2001-000387
2001-000660
2001-000786
2001-000449
2001-000281
2001-000290
2001-000660
2001-000449
2008-001013
2001-001138
2003-002008
2003-001025
2008-000264
2001-001114
2001-000022
2001-000020
2008-000251
2008-000278
2008-000251
2004-001899
2004-001967
2004-001390
2001-001114
2001-001043
2008-001013
2001-001043
2001-001043
2001-001043
2001-001043
2001-001043
2001-000429
2001-000429
2001-000429
2008-000254
2008-000299
2001-000490
2001-000490
2001-000490
2002-001009
2002-001009
2002-001009
2002-001009
Remark
R-CARBON;47OHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;3KOHM,5%,1/8W,AA,TP,R-CARBON(S);240KOHM,5%,1/2W,AA,TP,R-CARBON;15KOHM,5%,1/8W,AA,TP,R-CARBON(S);300KOHM,5%,1/2W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;1.3KOHM,5%,1/8W,AA,TP,R-CARBON;100KOHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;47OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;68OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;27KOHM,5%,1/8W,AA,TP,R-CARBON;3.3KOHM,5%,1/8W,AA,TP,R-CARBON;15KOHM,5%,1/8W,AA,TP,R-METAL;75Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;27KOHM,5%,1/8W,AA,TP,R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mm
R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;9.1KOHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;9.1KOHM,5%,1/8W,AA,TP,R-CARBON(S);1.2KOHM,5%,1/2W,AA,TP,R-CARBON(S);1.3KOHM,5%,1/2W,AA,TP,R-CARBON(S);1OHM,5%,1/2W,AA,TP,R-FUSIBLE(S);0.68ohm,5%,2W,AF,TP,3.9x10mm
R-METAL OXIDE;470ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;16KOHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,R-CARBON;47KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON(S);390OHM,5%,1/2W,AA,TP,R-METAL OXIDE(S);18Kohm,5%,2W,AF,TP,3.9x10mm
R-METAL OXIDE(S);15Kohm,5%,2W,AF,TP,3.9x10mm
R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm
R-CARBON(S);270OHM,5%,1/2W,AA,TP,R-CARBON(S);33OHM,5%,1/2W,AA,TP,R-CARBON(S);22OHM,5%,1/2W,AA,TP,R-FUSIBLE(S);0.27ohm,10%,2W,AF,TP,3.9x10mm
R-FUSIBLE(S);82ohm,5%,2W,AA,TP,3.9x10mm
R-FUSIBLE(S);0.27ohm,10%,2W,AF,TP,3.9x10mm
R-METAL(S);61.9Kohm,1%,1/2W,AA,TP,2.5x6.5
R-METAL(S);68Kohm,1%,1/2W,AA,TP,2.5x6.5mm
R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
R-CARBON(S);270OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);0.68ohm,5%,2W,AF,TP,3.9x10mm
R-FUSIBLE(S);47ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON;200OHM,5%,1/8W,AA,TP,R-CARBON;200OHM,5%,1/8W,AA,TP,R-CARBON;200OHM,5%,1/8W,AA,TP,R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0
R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0
Loc. No.
R520
R601
R602
R603
R604
R605
R606
R607
R701
R702
R703
R704
R705
R706
R707
R708
R709
R712
R713
R714
R715
R716
R717
R718
R719
R720
R721
R722
R723
R724
R725
R728
R729
R732
R733
R734
R735
R736
R740
R741
R801
R802
R803
R804
R805
R806
R807
R808
R809
R810
R811
R813
R814
R815
R816
R817
R818
R819
R820
R821
R822
R823
R824
R826
R901
R902
R903
R904
R905
R906
R908
R909
R910
R911
R912
R913
R914
Code No.
2001-001062
2008-001002
2008-001002
2001-000472
2001-000331
2001-000429
2001-000472
2001-000331
2001-000281
2001-000281
2001-000515
2001-000515
2001-000281
2001-000281
2001-000515
2001-000515
2001-000969
2001-000539
2001-000969
2001-000429
2001-000969
2001-000660
2001-000539
2001-000969
2001-000527
2001-000387
2001-000786
2001-000290
2001-000387
2001-000786
2001-000969
2001-000281
2001-000281
2001-000290
2001-000969
2001-000969
2001-000969
2001-000660
2701-000114
2701-000114
2002-001011
2003-000994
2003-000994
2001-001150
2001-001150
2003-001023
2001-001178
2002-001011
2002-001013
2003-000782
2003-000462
2001-000429
2001-000449
2004-001889
2004-001983
2001-001153
2001-000290
2001-000290
2008-001047
2008-000271
2001-000290
2008-000264
2001-001125
2001-001153
2001-000290
2001-000290
2001-000066
2004-000218
2004-000218
2004-000218
2001-000241
2001-000472
2001-000924
2001-000214
2001-000449
2001-000241
2001-000472
Remark
R-CARBON(S);10MOHM,5%,1/2W,AA,TP,R-FUSIBLE(S);0.18ohm,5%,2W,AA,TP,3.9x10mm
R-FUSIBLE(S);0.18ohm,5%,2W,AA,TP,3.9x10mm
R-CARBON;2.7KOHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;2.7KOHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;24KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,R-CARBON;24KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;22OHM,5%,1/8W,AA,TP,R-CARBON;16KOHM,5%,1/8W,AA,TP,R-CARBON;47KOHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;16KOHM,5%,1/8W,AA,TP,R-CARBON;47KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
R-COMPOSITION;3.3Mohm,10%,1/2W,AA,TP,3.7x9mm
R-CARBON(S);470KOHM,5%,1/2W,AA,TP,R-CARBON(S);470KOHM,5%,1/2W,AA,TP,R-METAL OXIDE(S);120ohm,0.05,2W,AF,TP,3.9x10mm
R-CARBON(S);680OHM,5%,1/2W,AA,TP,R-COMPOSITION;3.3Mohm,10%,1/2W,AA,TP,3.7x9mm
R-COMPOSITION;4.7Mohm,10%,1/2W,AA,TP,3.7x9mm
R-METAL OXIDE(S);7.5Kohm,5%,2W,AA,TP,4x12mm
R-METAL OXIDE(S);10Kohm,5%,2W,AA,TP,4x12mm
R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-METAL(S);127Kohm,1%,1/2W,AA,TP,2.5x6.5m
R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.4
R-CARBON(S);47OHM,5%,1/2W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);68ohm,5%,2W,AF,TP,3.9x10mm
R-FUSIBLE(S);3.3ohm,5%,2W,AA,TP,3.9x10mm
R-CARBON;10KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm
R-CARBON(S);300KOHM,5%,1/2W,AA,TP,R-CARBON(S);47OHM,5%,1/2W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON(S);10KOHM,5%,1/2W,AA,TP,R-METAL;10Kohm,1%,1/8W,AA,TP,1.8x3.2mm
R-METAL;10Kohm,1%,1/8W,AA,TP,1.8x3.2mm
R-METAL;10Kohm,1%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;1.5KOHM,5%,1/8W,AA,TP,R-CARBON;2.7KOHM,5%,1/8W,AA,TP,R-CARBON;680OHM,5%,1/8W,AA,TP,R-CARBON;1.1KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;1.5KOHM,5%,1/8W,AA,TP,R-CARBON;2.7KOHM,5%,1/8W,AA,TP,-
Samsung Electronics
Electric Parts List
Loc. No.
!
!
!
!
!
R918
R919
R920
R921
R922
R923
R924
R925
R926
R927
R928
R929
R930
R932
R933
R934
R935
R936
R937
R939
R941
R942
R945
R948
R951
R953
R954
R955
RE01
RE02
RE03
RE04
RE05
RE06
RE07
RE08
RE09
RE10
RL801
RP802
RP803
RT01
RT02
RT03
RT04
RT05
RT06
RT07
RT08
RT13
RT14
RT15
RT16
RT18
RT19
RT20
RW901
SF101
SW901
SW902
SW903
SW904
SW905
T401
T444
T801
TU101
V999
X202
X203
XT01
Z208
Code No.
2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000924 R-CARBON;680OHM,5%,1/8W,AA,TP,2001-000924 R-CARBON;680OHM,5%,1/8W,AA,TP,2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP,2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2001-000006 R-CARBON;2.4KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
2004-001914 R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mm
2001-000066 R-CARBON(S);10KOHM,5%,1/2W,AA,TP,2001-000066 R-CARBON(S);10KOHM,5%,1/2W,AA,TP,2001-000052 R-CARBON(S);3.3KOHM,5%,1/2W,AA,TP,2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
2003-000652 R-METAL OXIDE(S);330ohm,5%,2W,AF,TP,4x12mm
2001-001120 R-CARBON(S);3.3OHM,5%,1/2W,AA,TP,2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA,TP,3501-001040 RELAY-POWER;12VDC,500mW,10A,1FormA,15mS,5m
1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW,TP
1404-001087 THERMISTOR-PTC;7ohm,30%,220V,270V,19A,-,ST
2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2003-000676 R-METAL OXIDE(S);39ohm,5%,2W,AA,TP,4x12mm
2001-000347 R-CARBON;13KOHM,5%,1/8W,AA,TP,2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2011-000157 R-NETWORK;10K,5%,1/8W,A,SIP,6P,BK
2904-000302 FILTER-SAW AV;38.90MHz,-,ST,13.9dB,PAL-B/G,3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPST
3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPST
AA26-50001R TRANS-HORIZ DRIVE;-,80MH,580UH,4UH,G11A EI19,ST
AA26-30005QTRANS-FLYBACK;-,FUH-29A001(S),29/25,130V
AA26-20007WTRANS-SWITCHING;-,90~260V,130/15.5/12/8V,VDE,S
AA40-10006HTUNER-V/S;TELE4-108A,PAL-B/G,TR,181CH
3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,2801-000274 CRYSTAL-UNIT;4.433619MHz,30ppm,28-AAM,20pF,
2801-000226 CRYSTAL-UNIT;3.579545MHz,20ppm,28-AAM,15pF,
2801-003433 CRYSTAL-UNIT;12MHz,30ppm,28-AAA,30pF,30ohm,
2903-000181 FILTER-CERAMIC;TR,5.5MHz,-,-,-,TP,TPS5.5MB-TF
ASSY-PCB,A/V SIDE
*
Remark
AA95-00004AASSY-PCB,A/V SIDE;-,566B~569B,S51A,PAL,-,-
Samsung Electronics
Loc. No.
CA04
CA05
CA06
CA07
CN01A
CN05A
CN06A
JE01
JR01
LA04
LA05
RA01
RA02
Code No.
Remark
2202-000720 C-CERAMIC,MLC-AXIAL;8.2nF,20%,16V,Y5R,TP,3.5x19,2202-000720 C-CERAMIC,MLC-AXIAL;8.2nF,20%,16V,Y5R,TP,3.5x19,2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5

2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5
AA39-20068E LEAD-CONNECTOR,ASSY;-,YBNH025-08,67096-008,8P,500,
AA39-20069ALEAD-CONNECTOR,ASSY;-,YBNH025-05,67096-005,5P,500,
AA39-20499B LEAD CONNECTOR-ASSY;-,YBNH025-04,SMP025-04,4P,200
3722-000143 JACK-PHONE;1P(VER),3.4mm,AG,BLK,NO
3722-001031 JACK-RCA;3P,3.6mm,#18,AU
2001-000028 R-CARBON(S);100OHM,5%,1/2W,AA,TP,2001-000028 R-CARBON(S);100OHM,5%,1/2W,AA,TP,-
ASSY-SOUND
*
AA95-00101AASSY-SOUND;-,CK,S51A,MONO,-,EUROPE
CFM01
CFM02
CM01
CM02
CM03
CM04
CM05
CM06
CM07
CM08
CM09
CM10
CM11
CM12
CM13
CM14
CM15
CM16
CM17
CM19
CNN01
CNN02
DM01
DM02
DM03
DM04
ICM01
JM01
LM02
QM01
QM04
QM05
QM06
QM07
QM08
QM09
RM01
RM02
RM03
RM04
RM05
RM06
RM09
RM10
RM11
RM13
RM15
RM16
RM17
RM18
RM19
RM20
RM21
RM22
RM23
RM24
RM25
2904-001054
2904-001010
2301-000383
2401-000603
2401-002144
2305-000665
2202-000127
2202-000127
2301-000224
2301-000383
2202-000127
2202-000127
2202-000127
2401-001333
2401-001333
2401-000660
2401-000660
2401-000660
2401-000660
2301-000383
3711-002704
3711-002705
0401-001024
0401-001024
0401-000005
0401-000005
1204-001491
2701-000114
2701-000202
0504-000125
0504-000123
0504-000123
0504-000123
0504-000119
0504-000119
0501-000283
2001-000290
2001-000362
2001-000449
2001-000449
2001-000449
2001-000429
2001-000522
2001-000522
2001-000003
2001-000003
2001-000857
2001-000734
2001-000734
2001-000734
2001-000734
2001-000734
2001-000449
2001-000449
2001-000449
2001-000008
2001-000734
FILTER-SAW AV;38.9MHz,SIP5P,-,13.9dB,NTSC-M/
FILTER-SAW AV;32.9~33.4MHz,SIP5P,ST,14.4dB,P
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V,TP,-,7.5
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
CONNECTOR-HEADER;NOWALL,6P,1R,2.5mm,ANGLE,SN
CONNECTOR-HEADER;NOWALL,7P,1R,2.5mm,ANGLE,SN
DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TP
DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TP
DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP
DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP
IC-SOUND PROCESSOR;LA7566S,DIP,24P,300MIL,PLASTIC,1
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;560nH,10%,2.5x3.4mm
TR-DIGITAL;KSR1012,NPN,300mW,47K,TO-92,TP
TR-DIGITAL;KSR1004,NPN,300mW,47K-47K,TO-9
TR-DIGITAL;KSR1004,NPN,300mW,47K-47K,TO-9
TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,120R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;150OHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;22KOHM,5%,1/8W,AA,TP,R-CARBON;22KOHM,5%,1/8W,AA,TP,R-CARBON;330OHM,5%,1/8W,AA,TP,R-CARBON;330OHM,5%,1/8W,AA,TP,R-CARBON;560OHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;15KOHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,-
7-5
Electric Parts List
Loc. No.
RM27
RM28
TM01
ZM01
ZM03
Code No.
Remark
Loc. No.
Code No.
Remark
2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,AA26-10006L TRANS-IF;-,7MG,VIF,-,7mm,39pF,38.9MHz,S

2903-000200 FILTER-CERAMIC;BP,6.5MHz,+-70KHz,6dB,-,TP,2903-000185 FILTER-CERAMIC;BP,5.5MHz,+-75KHz,6dB,-,TP,-
ASSY-PCB,CONTROL
*
AA95-30002B ASSY-PCB,CONTROL;-,SCT12B,-,-
CN10A
CR01
LDR01
PAR01
RR01
RR02
AA39-20177ALEAD-CONNECTOR,ASSY;-,YBNH025-05,67096-005,5P,300,
2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
0601-000198 LED;ROUND,RED/GRN,5.0mm,630/565nm
AA59-60003J MODULE-REMOCON;-,ORC-06H2,38KHz,940nm,MESH,H,
2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,-
ASSY-R/G/B SWITCHING
*
AA95-90038K ASSY-R/G/B SWITCHING;-,-,S51A,PHILIPS MICOM ALL,-,-
CNS01
CNS02
CNS03
CS01
CS02
CS03
CS04
CS05
CS06
CS07
CS08
DS01
ICS01
RS01
RS04
RS06
RS07
RS08
RS09
RS10
RS11
RS12
RS13
RS14
RS15
RS16
RS17
RS18
3711-002702 CONNECTOR-HEADER;NOWALL,4P,1R,2.5mm,ANGLE,SN
3711-002703 CONNECTOR-HEADER;NOWALL,5P,1R,2.5mm,ANGLE,SN
AA39-20052F LEAD CONNECTOR-ASSY;-,YBNH025-04,YSH025-04,4P,200
2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5
1001-000223 IC-VIDEO SWITCH;TEA5114A,-,DIP,16P,334MIL,SING
2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,-
ASSY-POWER,CORD
!
LEADC
3403-000179 SWITCH-PUSH;250V,5A,DPST,-,JPW-2104B
AA39-10005APOWER-CORD;-,KKP419C,KLCE-2F,2.286MT,INLE
AA39-20175B LEAD CONNECTOR-ASSY;-,YFH150-03,-,3(2)P,200mm,1617
REMOCON
*
AA59-10116AREMOCON;-,TM59,SS,SZM503AT,29,-,-,L/GR
ASSY-HOLDER,SPK
*
AA91-60003AASSY-HOLDER,SPK;-,PP,-,-,8ohm 10W,CT2199
ASSY-CRT
!
AA03-10023R CRT-COLOR;-,A59KPR84X01(DB),+500mG,25,1
ASSY-ACCESSORY
AA39-40001B CABLE-RCA;-,RCA,1500mm,0.12/10,RED/WHT/Y
AA68-00043AMANUAL-USERS;S51A,RUS,-,B5,W/P100(G),-
7-6
Samsung Electronics
Block Diagram
8. Block Diagram
8-1 S51A
AUDIO-MODULE
SIF SAW FILTER
TDA9814T
SIF-DETECTOR
SPEAKER
8W 10W X 2
AUDIO-PROCESSOR
TDA9874
NICAM
DECODER
TDA7297
TDA9859
2CH AUDIO AMP

CRT
TUNER
TELE4-108A
SPM-171EE
IC
MCU
(TTX)
FREE-AMP
PAP103
RGB-AMP
TDA6108
VIF SAW FILTER

G3956M
H
E
A
T
E
R
1 CHIP
IF/VIDEO/CHROMA/DEFLECTION
TDA8844
VERTICAL AMP
LA7845
H
HV
+16.5V / -14V
EEPROM
X24C16
H-OUT TR
FBT
16.5V
FUH-29A003
180V
155V
5V
KA7630
SMPS
AC INPUT
AC230V OR 220 ~ 240V
Samsung Electronics
STR
KA3S1265R
8V
TRANS
15V
8-1
PCB Layout
9. PCB Layout
9-1 PCB Main
Loc. No.
DIODE
D101
D201
D202
D203
D204
D205
D206
D209
D210
D217
D301
D302
D303
D304
D401
D402
D403
D404
D405
D406
D407
D410
D507
D508
D509
D520
D601
D602
D603
D701
D801
D802
D803
D804
D805
D806
D807
D808
D809
D810
D812
D813
D901
D902
D903
D904
D905
D906
D907
DE01
DL201
DT01
DT02
DT03
DT04
DV801
DV802
DX01
DX02
DZ201
DZ202
DZ203
DZ204
DZ205
DZ206
DZ210
DZ302
DZ303
DZ304
DZ305
DZ306
DZ402
DZ403
DZ501
DZ502
78
171
168
166
163
155
125
112
127
30
105
124
105
97
114
128
70
89
106
37
20
10
312
312
312
268
214
223
223
172
246
255
230
228
173
168
156
269
187
183
160
167
231
188
188
188
199
229
227
94
155
260
242
201
223
264
251
19
60
142
106
155
158
125
121
109
107
99
102
94
118
90
75
309
316
236
131
131
131
139
226
167
164
148
238
131
104
84
121
67
126
109
28
148
109
76
86
223
220
216
225
205
200
198
210
31
60
37
31
22
39
63
92
122
132
70
100
138
143
140
138
161
124
124
108
206
120
116
161
128
7
7
8
7
197
218
120
229
148
170
148
121
108
131
133
135
91
165
190
190
Loc. No.
DZ503
DZ505
DZ601
DZ602
DZ603
DZ604
DZ701
DZ702
DZ703
DZ704
DZ705
DZ801
DZ802
DZ803
DZ804
DZ805
DZ807
DZ808
DZ901
DZ904
DZ905
DZ906
DZX01
296
321
223
223
223
223
49
54
59
41
64
231
218
150
177
183
166
209
227
211
280
321
39
IC
190
190
213
215
223
220
148
148
148
141
148
33
26
122
120
12
120
19
165
145
108
82
13
HC101
IC201
IC301
IC501
IC601
IC701
IC801
IC802
IC803
IC804
IC901
IC902
IC903
ICE01
60
85
123
315
238
17
245
201
201
148
267
274
193
130
224
198
132
178
185
190
9
19
95
127
134
105
120
118
TRANSISTOR
Q101
Q201
Q202
Q204
Q205
Q206
Q207
Q209
Q210
Q211
Q212
Q301
Q302
Q401
Q402
Q403
Q404
Q701
Q702
Q704
Q801
Q901
Q902
Q903
Q904
Q905
Q906
Q907
Q908
Q909
QE01
QT01
QT02
QX01
71
159
149
87
139
133
146
146
121
196
199
119
111
143
83
43
83
54
54
183
293
240
251
251
251
246
204
231
227
155
140
201
245
43
213
131
132
230
219
219
219
172
183
182
193
91
96
74
130
97
134
162
182
215
97
163
234
222
215
148
150
128
128
230
96
127
139
8
Y
Samsung Electronics
9-1
Wiring Diagram
10. Wiring Diagram

10-1 S51A
R
ANODE
L
CRT
ASSY-PWB FRONT,A/V
DY
CN701A
A S S Y -P W B M A IN
M
I
C
O
M
SW801
CN05A
CN501B
FOCUS
SOCKET
CRT
CN06A
SCR EE N
S O U ND
A MP
CN602
P IP /T T X
MO D U L E
S MP S
T R ANS
T
D
A
8
8
4
4
CN501
CN401
FBT
CN701
M
O
D
U
L
E
A
U
D
I
O
T
U
N
E
R
CN502
Samsung Electronics
10-1
MEMO
10-2
Samsung Electronics
Schematic Diagrams
11. Schematic Diagrams

11-1 MAIN (Power 21)
8
51
10
51
11
50
5
7
10
1
11
2
3
50
: Power Line
: Signal Line
Samsung Electronics
11-1
Schematic Diagrams
11-2 MAIN (Power 25 - 30)

8
51
10
11
12
6
50
4
5
7
12
10
9
11
50
51
: Power Line
: Signal Line
11-2
Samsung Electronics
Schematic Diagrams
11-3 PWB MAIN (One-Chip)
: Power Line
: Signal Line
13
14
15
16
17
18
19
20
21
22
23
24
13
26
27
29
30
25
24
28
23
32
31
22
18
21
17
16
20
15
14
19
32
Samsung Electronics
31
30
29
28
27
26
25
11-3
Schematic Diagrams
11-4 PWB MAIN (u-COM)
33
33
34
35
36
37
38
39
40
41
42
42
41
40
35
39
34
38
37
36
: Power Line
: Signal Line
11-4
Samsung Electronics
Schematic Diagrams
11-5 PWB MAIN (SUB)

46
47
46
48
47
49
48
49
: Power Line
: Signal Line
Samsung Electronics
11-5
Schematic Diagrams
11-6 PWB MAIN (Sound Module Mono)
11-6
Samsung Electronics
Schematic Diagrams
11-7 PWB MAIN (CRT)

43
43
44
44
45
43
45
44
45
OPTION
: Power Line
: Signal Line
Samsung Electronics
11-7
Schematic Diagrams
11-8 PWB MAIN (SOUND MODULE STEREO)
11-8
Samsung Electronics
Schematic Diagrams
11-9 PWB MAIN (SOUND MODULE NICAM)
Samsung Electronics
11-9
Schematic Diagrams
11-10 PWB MAIN (A/V FRONT / VIDEO SWITCH)
RGB - S/W MODULE
11-10
Samsung Electronics
www.s-manuals.com

Samsung ck6202x3s, ck6202x3x Chassis S51a Service Manual PDF

Uploaded by

Copyright:

Available Formats

Samsung ck6202x3s, ck6202x3x Chassis S51a Service Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Samsung ck6202x3s, ck6202x3x Chassis S51a Service Manual PDF

Uploaded by

Copyright:

Available Formats

COLOR TELEVISION RECEIVER

COLOR TELEVISION RECEIVER

Samsung Electronics Co., Ltd. FEB.1999

1-1 Safety Precautions

Fig. 1-1 AC Leakage Test

1-1 Safety Precautions (Continued)

15. Observe the original lead dress, especially

14. Components, parts and wiring that appear to

1-2 Servicing Precautions

5. Check the insulation between the blades of the

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

5. Use only a grounded-tip soldering iron when

Specifications and IC Data

2. Specifications and IC Data

Color Sub Carrier

In ter m e diate-F r equ en c ies (MH z ):

Quick start, in-line-gun,

P o w er R e qu ir e m en ts: AC 230 V, 50Hz or AC 220 ~ 240 V, 50Hz

Specifications and IC Data

PAL/SEC AM/NTSC /SE CAM-L

VE R TIC AL DEF LE CTION AMP

SOUND AMP (5W/C H)

SWITC HING R EGULATOR

SWITC HING R EGULATOR (5,8V)

SIF DETEC TOR

SIF & FM DE TE C TOR

SIF DETEC TOR (SECAM-L)

Specifications and IC Data

2-3 Semiconductor Base Diagrams

Fig. 2-1 Semiconductor Base Diagrams

Disassembly and reassembly

3. Disassembly and Reassembly

1. After removing the 7 screws, pull the cabinet backwards.

Disassembly and reassembly

3-2 Main Board Removal

1. Separate the TBC-wire 2P connector from GT501,GT502.

Disassembly and reassembly

3-3 Speaker Removal

1. Separate the speaker wires from D-coil

2. Remove the screws.

Disassembly and reassembly

3-4 CRT Removal

Alignment and Adjustments

4. Alignment and Adjustments

4-1-3 When CRT Is Replaced

1. Do not attempt these adjustments in the Video

2. The Factory Mode adjustments are necessary

3. Do not tamper with the Adjustment screen

4-1-2 When EEPROM (IC902) Is Replaced

4-2 Factory/Service Mode

4-2-1 Procedure for the Adjustment Mode

(1) STAND-BY DISPLAY MENU MUTE

5. The VOLUME keys increase or decrease the

After adjustments are completed, re-start

Alignment and Adjustments

4-2-2 Main Adjustment Parameters

AUTO GAIN CONTROL

VOLTAGE CONTROLLED OSCILLATOR

RED DRIVE GAIN