Aruba 8325 Switch SeriesInstallation and Getting Started Guide

Aruba 8325 Switch Series
Installation and Getting Started Guide
Part Number: 5200-5297a

Published: May, 2019
Edition: 2
© 2019 Hewlett Packard Enterprise Development LP
Notices
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard
Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software: Valid license from Hewlett Packard Enterprise required for possession, use, or
copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's
standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise
has no control over and is not responsible for information outside the Hewlett Packard Enterprise website.
Contents
Chapter 1 About this document ........................................................................ 7

Applicable products .................................................................................................................................... 7
Related publications ................................................................................................................................... 7
Chapter 2 Introducing the Aruba 8325 Switch ................................................. 9

Overview ..................................................................................................................................................... 9
Front of the switch .................................................................................................................................... 10
8325-48Y8C JL624A and JL625A switches........................................................................................ 10
8325-32C JL626A and JL627A switches ............................................................................................ 11
Network ports ...................................................................................................................................... 12
Management ports .............................................................................................................................. 14
Console port ................................................................................................................................ 14
Out-of-band management (OOBM) port ...................................................................................... 14
USB-A port .................................................................................................................................. 15
Chassis LEDs on the front of the switch ............................................................................................. 15
Port LEDs on the front of the switch.................................................................................................... 17
Reset button........................................................................................................................................ 21
Switch product label ............................................................................................................................ 21
Back of the switch ..................................................................................................................................... 22
Power supplies.................................................................................................................................... 23
Power supply status LED ............................................................................................................ 24
Load sharing ................................................................................................................................ 24
Redundancy ................................................................................................................................ 24
Hot swapping ............................................................................................................................... 25
Fan assemblies ................................................................................................................................... 25
Fan assembly status LED ............................................................................................................ 26
Switch features ......................................................................................................................................... 27
Chapter 3 Installing the switch ........................................................................ 29

Included parts ........................................................................................................................................... 29
Parts not included ..................................................................................................................................... 29
Installation procedures ............................................................................................................................. 30
Summary............................................................................................................................................. 30
Installation precautions ............................................................................................................................. 31
1. Prepare the installation site .................................................................................................................. 32
2. Install power supplies ........................................................................................................................... 32
3. Install fan assemblies ........................................................................................................................... 33
4. Power-on the switch and check LEDs .................................................................................................. 34
5. Power off the switch ............................................................................................................................. 36
6. Mount the switch ................................................................................................................................... 36
Mounting an Aruba 8325 switch.......................................................................................................... 36
Two-post rack mount option: ....................................................................................................... 36
Four-post rack mount option: ....................................................................................................... 37
7. Install transceivers ................................................................................................................................ 39
Interface-Group operation ................................................................................................................... 40
1GBase-T (J8177D) transceiver support restrictions in the 48-port 8325 switches ..................... 41
10GBase-T (JL563A) transceiver support restrictions in the 48-port 8325 switches ................... 41
Installing transceivers:......................................................................................................................... 42
Removing transceivers:....................................................................................................................... 43
3
8. Connect the switch to a power source .................................................................................................. 43
9. Set up for initial configuration ............................................................................................................... 44
10. Connect the network cables ............................................................................................................... 45
Using the RJ-45 out-of-band management port.................................................................................. 45
Connecting cables to transceivers ...................................................................................................... 45
Chapter 4 Initial configuration with an out-of-band serial connection ........ 47

Terminal configuration .............................................................................................................................. 47
Connect to console port ............................................................................................................................ 47
Console cable pinouts .............................................................................................................................. 48
Chapter 5 Replacing components................................................................... 49

Replacing a power supply ........................................................................................................................ 49
Replacing a fan assembly ........................................................................................................................ 50
Chapter 6 Troubleshooting .............................................................................. 53

Basic troubleshooting tips ......................................................................................................................... 53
Diagnosing with the LEDs ........................................................................................................................ 54
LED patterns for general switch troubleshooting ................................................................................ 54
Diagnostic tips: ............................................................................................................................ 54
Hardware diagnostic tests ........................................................................................................................ 57
Testing the switch by resetting it ......................................................................................................... 57
Checking the switch LEDs .................................................................................................................. 57
Checking console messages .............................................................................................................. 57
Testing switch-to-device network communications ............................................................................. 57
Testing end-to-end network communications ..................................................................................... 57
Battery ...................................................................................................................................................... 58
Downloading new switch software ............................................................................................................ 58
Hewlett Packard Enterprise Customer Support Services ......................................................................... 58
Chapter 7 Specifications .................................................................................. 59

Switch specifications ................................................................................................................................ 59
Physical............................................................................................................................................... 59
Electrical.............................................................................................................................................. 59
Power Consumption............................................................................................................................ 59
MTBF .................................................................................................................................................. 60
Environmental ..................................................................................................................................... 60
Acoustics............................................................................................................................................. 60
RoHS................................................................................................................................................... 60
Standards ................................................................................................................................................. 61
Chapter 8 Cabling and technology information............................................. 63

Cabling specifications ............................................................................................................................... 63
Technology distance specifications .......................................................................................................... 64
Chapter 9 Support and other resources ......................................................... 67

Accessing Hewlett Packard Enterprise support ........................................................................................ 67
Before calling support ............................................................................................................................... 67
Accessing updates ................................................................................................................................... 68
Websites ................................................................................................................................................... 68
Customer self repair ................................................................................................................................. 68
Remote support ........................................................................................................................................ 69
4 Aruba 8325 Switch Installation and Getting Started Guide

Documentation feedback .......................................................................................................................... 69
5
Chapter 1
About this document
This document is intended for network administrators and support personnel.
The display and command line illustrated in this document are examples and might not exactly
match your particular switch or environment. The switch and accessory drawings in this document
are for illustration only, and may not exactly match your particular switch and accessory products.
Applicable products
Aruba 8325-48Y8C 48p 25G SFP/+/SFP28 8p 100G QSFP+/ JL624A
QSFP28 Front-to-Back 6 Fans and 2 PSU Bundle
Aruba 8325-48Y8C 48p 25G SFP/+/SFP28 8p 100G QSFP+/ JL625A
QSFP28 Back-to-Front 6 Fans and 2 PSU Bundle
Aruba 8325-32C 32-port 100G QSFP+/QSFP28 Front-to-Back JL626A
6 Fans and 2 Power Supply Bundle
Aruba 8325-32C 32-port 100G QSFP+/QSFP28 Back-to-Front JL627A
6 Fans and 2 Power Supply Bundle
Related publications
• START HERE: Installation, Safety, and Regulatory Information for the Aruba 8325 Switches
• ArubaOS-Switch and ArubaOS-CX Transceiver Guide
• Aruba 8325 Fundamentals Guide for ArubaOS-CX 10.02 (or greater)
• Aruba 8325 configuration manuals
To view and download the latest version of the above publications, visit the Aruba Support Portal at
https://asp.arubanetworks.com/downloads
Chapter 1 About this document 7

Chapter 2
Introducing the Aruba 8325 Switch
Overview
The Aruba 8325 switch is a multiport switch that can be used to build high-performance switched networks. The
switch is a store-and-forward device offering low latency for high-speed networking. The Aruba 8325 switch also
supports full network management capabilities.
Table 1: Switches described in this manual
Switch Description
Aruba 8325-48Y8C 48p 25G SFP/+/SFP28 8p 100G QSFP+/ Includes a 48-port of 1/10/25Gbps and 8-port
QSFP28 Front-to-Back 6 Fans and 2 PSU Bundle (JL624A) of 40/100Gbps switch with six fans and two
power supplies installed with front-to-back
airflow
Aruba 8325-48Y8C 48p 25G SFP/+/SFP28 8p 100G QSFP+/ Includes a 48-port of 1/10/25Gbps and 8-port
QSFP28 Back-to-Front 6 Fans and 2 PSU Bundle (JL625A) of 40/100Gbps switch with six fans and two
power supplies installed with back-to-front
airflow
Aruba 8325-32C 32-port 100G QSFP+/QSFP28 Front-to-Back Includes a 32-port of 40/100Gbps switch with
6 Fans and 2 Power Supply Bundle (JL626A) six fans and two power supplies installed with
front-to-back airflow
Aruba 8325-32C 32-port 100G QSFP+/QSFP28 Back-to-Front Includes a 32-port of 40/100Gbps switch with
6 Fans and 2 Power Supply Bundle (JL627A) six fans and two power supplies installed with
back-to-front airflow
Table 2: Accessories list
Accessories
Power supplies* Aruba 8325 650W 100-240VAC FB PSU (JL632A)

Aruba 8325 650W 100-240VAC BF PSU (JL633A)
Fan assemblies* Aruba 8325-48Y8C Front-to-Back Fan (JL628A)

Aruba 8325-48Y8C Back-to-Front Fan (JL629A)
Aruba 8325-32C Front-to-Back Fan (JL630A)
Aruba 8325-32C Back-to-Front Fan (JL631A)
Chassis Aruba 8325-48Y8C 48p 25G 8p 100G Swch (JL635A)

Aruba 8325-32C 32p 100G Swch (JL636A)
Rack mount kits (Not Aruba X472 2-Post Rack Kit (JL482B)
included. Ordered
Aruba X474 4-Post Rack Kit (JL483B)
separately.)
* Field replaceable units (FRUs).
Chapter 2 Introducing the Aruba 8325 Switch 9

This chapter describes this switch with the following information:
• Front of the switch:
◦ Network ports
◦ Console port
◦ Out-of-band management (OOBM)
◦ LEDs
◦ Reset button
• Back of the switch:
◦ Power supplies and connectors
◦ Fan assemblies
◦ LED indicators for fan assemblies and power supplies
• Switch features
◦ Hardware features
◦ Software features
◦ Management software
Front of the switch

8325-48Y8C JL624A and JL625A switches
Figure 1: Front of the Aruba 8325-48Y8C (JL624A and JL625A)
3 4 5
1 2
11 10 9 8 7
Table 3: Front of the Aruba 8325-48Y8C (JL624A and JL625A)
Label Description
1 Power Supply 1 and 2 (PS1/PS2), Fan, Global Status, and Unit Identification LEDs
2 SFP28 ports (these ports support SFP/SFP+/SFP28 transceivers)
3 SFP28 port LEDs. For port LED detail, see “Port LEDs on the front of the switch” on
page 17.
4 QSFP28 port LEDs

The first port lane LED (far left) acts as the main port LED in each group of four.
Post boot-up/self-test, the remaining three LEDs are not used by the switch, and should remain
off throughout the product's operation.
5 RJ-45 10/100/1000Base-T Out-of-Band Management Port (OOBM)
6 RJ-45 serial console port

Table 3: Front of the Aruba 8325-48Y8C (JL624A and JL625A) (Continued)
Label Description
7 Switch product label. Pull the tab out to view the product label information.
8 Micro-USB serial console port
9 USB-A Port for file management and HPE-Aruba Accessories
10 QSFP28 ports (these ports support QSFP+ and QSFP28 transceivers)
11 Reset button
8325-32C JL626A and JL627A switches

Figure 2: Front of the Aruba 8325-32C (JL626A and JL627A)
1 2 3 4 5
8 7 6
Table 4: Front of the Aruba 8325-32C (JL626A and JL627A)
Label Description
1 Power Supply 1 and 2 (PS1/PS2), Unit Identification, Global Status, and Fan LEDs
2 QSFP28 ports (these ports support QSFP+ and QSFP28 transceivers)
3 QSFP28 port LEDs

The first port lane LED (far left) acts as the main port LED in each group of four.
Post boot-up/self-test, the remaining three LEDs are not used by the switch, and should
remain off throughout the product's operation.
4 RJ-45 10/100/1000Base-T Out-of-Band Management (OOBM) Port
5 USB-A Port for file management and HPE-Aruba Accessories
6 Switch product label. Pull the tab out to view the product label information.
7 RJ-45 serial console port
8 Reset button

Network ports
Table 5: Network ports
Product Model name SFP28 ports1, 3 QSFP28 ports2

number
JL624A and Aruba 8325-48Y8C FB 6 F 2 PS Bdl 48 8

JL625A
JL626A and Aruba 8325-32C FB 6 F 2 PS Bdl – 32

JL627A
Notes:
1 SFP28 ports support 1G SFP, 10G SFP+, and 25G SFP28 transceivers.
2
QSFP28 ports support 40G QSFP+ and 100G QSFP28 transceivers.
3 For information on supported speeds, refer to “Interface-Group operation” on page 40.
This product also supports optional network connectivity:
Table 6: Optional network connectivity, speeds, and technologies
Transceiver form-factor and connector1
Speed Technology Cabling SFP ("mini- SFP+ SFP28 QSFP+ QSFP28

GBIC") connector connector connector connector
Connector
1 Gbps 1-Gig T2 Copper – – – – –

(twisted-pair)
1-Gig SX Fiber LC – – – –
(multimode)
1-Gig LX Fiber LC – – – –
(multimode or
single mode)
1-Gig LH Fiber (single LC – – – –

mode)
10 Gbps 10-Gig Copper – – – – –

Direct Attach (twinaxial)
10-Gig AOC Fiber – – – – –

(multimode)
10-Gig BT3, 4 Copper – – – – –

(twisted-pair)5
10-Gig SR Fiber – LC6 – – –

(multimode)
10-Gig LR Fiber (single – LC – – –

mode)
10-Gig ER Fiber (single – LC – – –

mode)

Table 6: Optional network connectivity, speeds, and technologies (Continued)

Connector


(multimode)
25-Gig SR Fiber – – LC – –
(multimode)
25-Gig eSR Fiber – – LC – –

(multimode)
25-Gig LR Fiber (single – – LC – –

mode)


(multimode)
40-Gig SR4 Fiber – – – MPO7 –

(multimode)
40-Gig ESR4 Fiber – – – MPO –

(multimode)
40-Gig LR4 Fiber (single – – – LC –

mode)
40-Gig ER4 Fiber (single – – – LC –

mode)
40-Gig Bidi Fiber (single – – – LC –

mode)
100 Gbps 100-Gig Copper – – – – –


(multimode)
100-Gig SR4 Fiber – – – – MPO

(multimode)
100-Gig LR4 Fiber (single – – – – LC

mode)

Table 6: Optional network connectivity, speeds, and technologies (Continued)

Connector
1 For supported transceivers:
• Go to the Aruba Support Portal at https://asp.arubanetworks.com/downloads.
• Filter for (1) Product Family, (2) Product Series, (3) Document File Contents.
• Select the ArubaOS-Switch and ArubaOS-CX Transceiver Guide link.
For technical details of cabling and technologies, see “Cabling and technology information” on page 63.
2
RJ-45 Cat 5e cable is needed for connecting this transceiver. The max link length specified is 100m.
3
10GBase-T transceiver limited support:
-only supported in ports 1-2, 4-5, 7-8, 10-11, 13-14, 16-17. Use in any other port generates an “Incompatible
interface” error.
-maximum twelve 10GBase-T transceivers (both interface-groups 1 & 2 must be set for 10G operation).
4
RJ-45 shielded Cat 6A cable is needed for connecting up this transceiver. The max link length specified is 30m.
5
CAT6A F/FTP, S/FTP, SF/FTP highly recommended in noisy environments. Refer to Aruba
Support_Advisory_JL563A_10GBaseT_APSC-RS20180403-01 for more information.
6
The Lucent Connector (LC) is a small form factor fiber optic connector.
7
The Multifiber Push On (MPO) connector is a 12-fiber optical connector.
Management ports
Console port
The Aruba 8325-48Y8C and 8325-32C switches include an RJ-45 serial console port. This port is used to connect
a console to the switch by using an RJ-45 serial cable (not supplied). A DB9-to-RJ-45 console cable can be
ordered from HPE: JL448A, Aruba X2C2 RJ45 to DB9 Console Cable.
The 8325-48Y8C switches also include an additional Micro USB serial console port. This port can be used to
connect a console to the switch by using a standard Micro USB cable (not supplied). The Micro USB connector has
precedence for input. If both cables are plugged in, the console output is echoed to both the RJ-45 and the Micro-
USB ports, but the input is only accepted from the Micro-USB port.
For more information on the console connection, see “9. Set up for initial configuration” on page 44. The
console can be a PC or workstation running a VT-100 terminal emulator, or a VT-100 terminal.
The Aruba CX mobile app and the Aruba USB Bluetooth adapter enable you to configure your switch from your
mobile device. For information about using the Aruba CX mobile app to configure the switch, see the
Fundamentals Guide for your switch and software release.
Out-of-band management (OOBM) port

This RJ-45 port is used to connect a dedicated management network to the switch. To use it, connect an RJ-45
network cable to the management port to manage the switch through SSH or Telnet from a remote PC or a UNIX
workstation.
To use this port, see the Aruba 8325 Fundamentals Guide for ArubaOS-CX. For more detailed information, refer to
the switch software manuals for your switch provided at the Aruba Support Portal at
https://asp.arubanetworks.com/downloads.

A networked out-of-band connection through the management port allows you to manage data network switches
from a physically and logically separate management network.
USB-A port
A USB-A port for file management, downloading switch software code, or use of HPE-Aruba accessories. This port
uses a USB Type-A connector and complies with all USB protocols and standards.
Chassis LEDs on the front of the switch

• Table 9 on page 16 describes the switch chassis LEDs.
• Table 11 on page 18 describes the switch port LEDs and their different behaviors for the JL624A and JL625A.
• Table 13 on page 20 describes the switch port LEDs and their different behaviors for the JL626A an JL627A.
Figure 3: Chassis LEDs for the Aruba 8325-48Y8C (JL624A and JL625A)
1
2
4
5
Table 7: Chassis LED labels for the Aruba 8325-48Y8C (JL624A and JL625A)
Label Description
1 Power Supply 1 (PS1) LED
3 Fan LED
4 Global Status LED
5 Unit Identification LED

Figure 4: Chassis LEDs for the Aruba 8325-32C (JL626A and JL627A)
Table 8: Chassis LED labels for the Aruba 8325-32C (JL626A and JL627A)
Label Description
1 Unit Identification LED
2 Global Status LED
5 Fan LED
Table 9: Chassis LED behavior
Chassis LEDs Function State Meaning
PS1/PS2 Power supply status On green Power supply is installed and

operating with all power
supplies and fans installed and
no faults are present.
On amber Fault detected for installed

power supply, or power supply
is not receiving power.
Off Power supply is not installed.
Fan Fan tray status On green System fans are operating

normally.
On amber One or more system fans has a

fault, or the minimum number of
fans are not installed.

Table 9: Chassis LED behavior (Continued)
Global Status Internal power status of On green The switch has passed self-test
the switch. and is powered up normally with
all power supplies and fans
Self-test status
installed and no faults are
Switch/port fault status present.
Flashing amber • The switch initialization is in

progress during bootup.
• A fault or initialization failure
has occurred on the switch,
one of the switch ports,
power supplies, or a fan.
The port LEDs with the fault
will flash simultaneously.
LEDs for power supplies
and fans with a fault will be
on amber.
• Port-speed mismatch. A
transceiver is installed in a
port configured for a
different speed.
Off The unit is not receiving power.
UID (Unit Identification) The Unit Identification On blue or flashing blue The “LED locator on” command
LED is used to help you allows you to turn on the LED.
to identify a particular
The “LED locator flashing”
unit in a rack or
command will flash the LED.
collection of products.
Off The "LED locator off" command
turns off the LED.
Port LEDs on the front of the switch

Figure 5: Port LEDs for the Aruba 8325-48Y8C (JL624A and JL625A)
1 2 3 4 5 6 7 8 9

Table 10: Port LED labels for the Aruba 8325-48Y8C (JL624A and JL625A)
Label Description
1 Upper SFP28 port LED
2 Middle SFP28 port LED
3 Lower SFP28 port LED
4 QSFP28 port LED and lane 1 indicator
5 QSFP28 lane 2 LED
6 QSFP28 lane 3 LED
7 QSFP28 lane 4 LED
8 Out-of-band management port Link LED
9 Out-of-band management port Act (activity) LED
Table 11: Port LED behavior for the Aruba 8325-48Y8C (JL624A and JL625A)
SFP28 port LEDs To display link and On/flashing green Shows a valid link at 25/10 Gbps.
activity information for
the port. • Fast flashing1 indicates port
activity at 25 Gbps.
• Slow flashing2 indicates port
activity at 1 or 10 Gbps.
Flashing amber When the Global Status LED is

simultaneously flashing amber,
indicates a port-speed mismatch,
an incompatible, unsupported, or
faulty transceiver, or a port failure.
Off Port is disabled, not connected, or

not receiving a link beat signal.

Table 11: Port LED behavior for the Aruba 8325-48Y8C (JL624A and JL625A) (Continued)
QSFP28 port LEDs To display link and On/flashing green Shows a valid link at 100/40 Gbps.
the port. • Fast flashing1 of the Lane 1
LED indicates port activity at
100 Gbps.
• Slow flashing2 of the Lane 1
40 Gbps.

simultaneously flashing amber with
the Lane 1 LED, indicates an
unsupported or faulty transceiver,
or a port failure.

Lanes 2-4 are always off and are
currently unused by HPE-Aruba
software.
Management port Link To display link On green Shows a valid link.

LED information for the port.
Management port Act To display activity Flashing yellow Flashing indicates port activity.
1 The fast flashing behavior is an on/off cycle once every 0.8 seconds, approximately.
2
The slow flashing behavior is an on/off cycle once every 1.6 seconds, approximately.
Figure 6: Port LEDs for the Aruba 8325-32C (JL626A and JL627A)
1 2 3 4 5 6

Table 12: Port LED labels for the Aruba 8325-32C (JL626A and JL627A)
Label Description
1 QSFP28 port LED and lane 1 indicator
2 QSFP28 lane 2 LED (Not supported with currently released software.)
5 Unused
6 Out-of-band management port Link and Activity LED
Table 13: Port LED behavior for the Aruba 8325-32C (JL626A and JL627A)
QSFP28 port LEDs To display link and On/flashing green Shows a valid link at 100/40 Gbps.
the port. • Fast flashing1 of the Lane 1
100 Gbps.
• Slow flashing2 of the Lane 1
40 Gbps.

simultaneously flashing amber with
the leftmost LED, indicates an
unsupported or faulty transceiver,
or a port failure.

Lanes 2-4 are always off and are
currently unused by HPE-Aruba
software.
Management port Link To display link On green Shows a valid link.

Management port Act To display activity Flashing green Flashing indicates port activity.
1
The fast flashing behavior is an on/off cycle once every 0.8 seconds, approximately.
2
The slow flashing behavior is an on/off cycle once every 1.6 seconds, approximately.

Reset button
The Reset button is recessed from the front panel (to protect it from being pushed accidentally) and is accessible
through a small hole on the front panel. Use a pointed object, such as an unbent paper clip, to push the button.
The Reset button is used as follows:
Table 14: Reset button
To accomplish this: Do this: This will happen:
Soft Reset Press and release the Reset The switch operating system is
button cleared gracefully (such as data
transfer completion, temporary
error conditions are cleared), and
then reboots.
Note: The Reset button is provided for your convenience. If you are concerned with switch security, make
sure that the switch is installed in a secure location, such as a locked wiring closet.
Switch product label

The switch product label is an Aruba Orange-colored tab on the bottom right side of the switch front panel. Pull the
tab out to view the product label information.
The product label information includes the part number, model number, serial number, and MAC address. The
information and bar codes are on two labels affixed to the top and bottom of the product label tab.
Figure 7: Aruba 8325 switch product label
Table 15: Aruba 8325 switch product label
Label Description
1 Product label top side. Information includes the serial number and MAC address.
2 Product label bottom side. Information includes the part number and model number.

Back of the switch
The back of the switch includes two power supply units and six fan assemblies.
Figure 8: Back of the Aruba 8325-48Y8C (JL624A and JL625A)
1 2 3 4 5 6 7 8 9
13 12 11 10
Table 16: Back of the Aruba 8325-48Y8C (JL624A and JL625A) switch labels and descriptions
Label Description
1 Power supply 2
2 Fan assembly 6
3 Fan assembly 5
4 Fan assembly 4
5 Fan assembly 3
6 Fan assembly 2
7 Fan assembly 1
8 Power supply status LED
9 Power supply 1
10 Ground lug
11 Fan assembly status LED
12 Color-coded power supply release latch

red = front-to-back air flow
blue = back-to-front air flow
13 Ground lug

Figure 9: Back of the Aruba 8325-32C (JL626A and JL627A)
1 2 3 4 5 6 7 8 9 10
13 12 11
Table 17: Back of the Aruba 8325-32C (JL626A and JL627A) labels and descriptions
Label Description
1 Power supply 2 1
2 Fan assembly 6
3 Fan assembly 5
4 Fan assembly 4
5 Fan assembly status LED
6 Fan assembly 3
7 Fan assembly 2
8 Fan assembly 1
9 Power supply status LED
10 Power supply 1 1
11 Ground lug
12 Color-coded power supply release latch

red = front-to-back air flow
blue = back-to-front air flow
13 Ground lug
1 Color-coded power supply release latch: red = front-to-back air flow; blue = back-to-front air flow.
Power supplies
The Aruba 8325 switch does not have a power switch; it is powered on when at least one installed power supply is
connected to an active AC power source. The power supplies automatically adjust to any voltage between 100-127
and 200-240 volts and either 50 or 60 Hz. There are no voltage range settings required.
Never insert or remove a power supply while the power cord is connected. Verify that cord has been
disconnected from the power supply before installation or removal.

The Aruba 8325 switch power supplies adapt electrical power for use with the switch. The chassis has two slots
that can hold individual power supplies to support load sharing, redundancy, and fault tolerance. Two 650W color-
coded power supplies are available for use with Aruba 8325 switches. A red release latch indicates an FB cooling
air flow. A blue release latch indicates a BF cooling air flow.
Figure 10: Aruba 8325 power supplies
1 2
Table 18: Aruba 8325 power supplies
Label Description
1 Aruba 8325 650W 100-240VAC FB PSU (JL632A)
2 Aruba 8325 650W 100-240VAC BF PSU (JL633A)
The Aruba 8325 switch is shipped with two hot-swappable, field-replaceable, AC power supplies. Each power
supply has a country-specific power cord for connection to an AC power outlet. The switch can operate with one
active power supply.
Power supply status LED

Table 19: Power supply LED behavior
Power Supply Function State Meaning

LED
Status LED To display power On green The power supply is operating normally.
supply status.
Flashing green or The power supply is experiencing a fault, or has
on red AC power but is not installed in the switch unit.
Off AC power is not connected to the power supply

or, if AC power is connected, the power supply is
in protection mode due to a voltage, current,
thermal, or short-circuit condition.
Load sharing
Load sharing occurs when two power supplies are installed in the switch and turned on. Load sharing divides the
total power load of the switch among both power supplies.
Redundancy
With power redundancy, the Aruba 8325 switch can continue normal operation even when one power supply fails
or is powered off. When two power supplies are installed, if one becomes unavailable (fails, or is powered off or
removed) the remaining power supply provides full power for the device.

Hot swapping
Hot swapping allows you to replace one failed power supply while the other provides full power. This makes it
unnecessary to shut down the switch during the replacement procedure.
Never insert or remove a power supply while the power cord is connected. Verify that the cord has
been disconnected from the power supply before installation or removal.
Fan assemblies
The Aruba 8325 switch is equipped with six field-replaceable, hot-swappable fan assemblies. Each fan assembly
features individual fans that pull air through the chassis from front to back (FB) or from back to front (BF).
Fans and power supplies installed in a given 8325 switch must have the same cooling air flow
direction (FB or BF). Air flow direction in an 8325 switch is not controlled by software. To change the
air flow direction, replace the power supplies and fans with power and fan units supporting the air flow
direction you want. See Figure 10 on page 24, Table 20 on page 25, and Figure 11 on page 26.
A minimum of five fan assemblies is required for operation. The system will automatically shutdown if
overheating is detected. If five or fewer fan assemblies are installed, the Fan LED will be on amber
and the Global Status LED will flash amber to indicate a fan fault may exist.
System airflow direction (FB or BF) is configured automatically at system initialization and cannot be
reconfigured by the user. System airflow direction is determined by the power supply type installed in
PS1 at initialization time (or PS2 if PS1 is absent). Any Fan assembly or Power supply of conflicting
airflow type will be disabled by the system. Ensure only matching Fan assemblies and power supplies
are used at any given runtime.
Fans designed for the 48-port 8325 switches are not compatible with 32-port 8325 switches and
vice-versa.
Fan models are color-coded for FB or BF cooling air flow.

• Red handle indicates a front-to-back (FB) cooling air flow.
• Blue handle indicates a back-to-front (BF) cooling air flow.
See the following table for fan usage.
Table 20: Aruba 8325 fan assemblies
Fan assembly Color code 48-port switches 32-port switches
Aruba 8325-48Y8C Front-to-Back Fan (JL628A) Red Yes No
Aruba 8325-48Y8C Back-to-Front Fan (JL629A) Blue Yes No
Aruba 8325-32C Front-to-Back Fan (JL630A) Red No Yes
Aruba 8325-32C Back-to-Front Fan (JL631A) Blue No Yes

Figure 11: Aruba 8325 fan assemblies
2 4
Table 21: Aruba 8325 fan assemblies
Label Description
1 Fan release latch
2 Aruba 8325-48Y8C Front-to-Back Fan (JL628A)
3 Fan release screw
4 Aruba 8325-32C Back-to-Front Fan (JL631A)
The switch can tolerate the failure of a single fan assembly while maintaining a safe operating temperature. The
switch may continue to operate with one failed fan assembly. If the switch reaches an overtemp condition, the
switch will shut down. For best operation, the failed fan assembly should be replaced as soon as possible.
If one or more of the fan assemblies have failed, the front-panel Fan LED will be on amber and failed fan assembly
LEDs will be on red.
If multiple fans have failed, the switch should be immediately powered off and the fan assemblies replaced.
The Aruba 8325 switch is not compatible with fan assemblies from other Aruba hardware platforms.
Fan assembly status LED

Table 22: Fan assembly LED behavior
Fan assembly LED Function State Meaning
Status LED To display fan assembly On green The fan assembly is operating
status. normally.
On red The fan assembly has been

disabled by the system due to
system airflow direction conflict
or has failed.
Use the show environment fan command for fan status information. (See the Aruba 8325 Fundamentals
Guide for ArubaOS-CX 10.02 or later at https://asp.arubanetworks.com/downloads.)

Switch features
The features of the Aruba 8325 switch include:
• Combinations of fixed QSFP28 and SFP28 ports, as described under Network ports.
• For secure environment, all ports are disabled by default.
• The option to have one or two power supplies: A second power supply supports redundant system power. If
one of the power supplies fails, the second power supply immediately provides the power necessary to keep
the switch running.
• The QSFP28 and SFP28 ports always operate at full duplex.
• Easy management of the switch through several available interfaces:
◦ Command line interface—A full featured, easy to use, VT-100 terminal interface for out-of-band switch
management.
◦ Web browser interface--An easy to use built-in graphical interface that can be accessed from common
web browsers.
• Support for the Spanning Tree Protocol to eliminate network loops.
• Support for up to 4094 IEEE 802.1Q-compliant VLANs so you can divide the attached end nodes into logical
groupings that fit your business needs.
• Support for many advanced features to enhance network performance.
• To download product updates, go to either of the following:
◦ Hewlett Packard Enterprise Support Center Get connected with updates page:
www.hpe.com/support/e-updates
◦ HPE Networking Software: www.hpe.com/networking/software
◦ To view and update your entitlements, and to link your contracts and warranties with your profile, go to the
Hewlett Packard Enterprise Support Center’s More Information on Access to Support Materials page:
www.hpe.com/support/AccessToSupportMaterials

Chapter 3
Installing the switch
This chapter shows how to install the switch. The Aruba 8325 switch requires you to order a rack mount kit that
includes the brackets for mounting the switch in a standard 19-inch telco rack, or in an equipment cabinet.
Included parts
• Documentation kit
• USB Bluetooth adapter enables you to configure your switch from your mobile device. Requires the Aruba CX
Mobile App. (Adapter is attached to a card in the documentation kit). For information about using the Aruba CX
mobile app to configure the switch, see the Fundamentals Guide for your switch and software release.
• Power cord, one of the following. Part number or J-number (SKU) is orderable through Aruba purchasing
systems.
Argentina 8121-0729 J9891A Israel 8121-1004 J9899A
Australia/New Zealand 8121-0837 J9883A Japan 8121-1143 J9893A
Brazil 8121-1071 J9894A Switzerland 8121-0738 J9898A
Chile 8121-0735 J9886A South Africa 8121-0737 J9897A
China 8121-0943 J9890A Taiwan 8121-0964 J9887A
Continental Europe/South
8121-0731 J9885A Philippines/Thailand 8121-0734 J9895A
Korea
UK/Hong Kong/Singapore/
Denmark 8121-0733 J9888A 8121-0739 J9884A
Malaysia
India 8121-0564 J9892A US/Canada/Mexico 8121-1141 J9896A
NA Hi-Voltage (non-locking) PDU NA/Japan/TW 8121-1091 J9943A
8120-3396 J9936A
C13 to NEMA 6-20
PDU Rest of World 8121-1094 J9944A
NA Hi-Voltage (locking) C15
8121-0941 J9955A* PDU India-only P09371-001 JL671A
to NEMA L6-20
* Ordered separate from the switch. To order a switch that will use a J9955A power cord, use the “no power
cord” option, #AC3, and specify the J9955A power cord as a separate line item in the order.
Parts not included

If you have not already done so, order an Aruba rack mount kit for use with your 8325 switch.
Rack mounting your Aruba 8325 switch is supported using these rack mount kits:
• JL482B, Aruba X472 2-Post Rack Kit (Not included. Ordered separately.)
• JL483B, Aruba X474 4-Post Rack Kit (Not included. Ordered separately.)
Chapter 3 Installing the switch 29

A DB9-to-RJ-45 console cable can be ordered from HPE: JL448A, Aruba X2C2 RJ45 to DB9 Console Cable.
Installation procedures
Summary
1. Prepare the installation site (page 32). Ensure the physical environment into which you will be installing the
switch is properly prepared, including having the correct network cabling ready to connect to the switch and
having an appropriate location for the switch. See “Installation precautions” on page 31 for some guidelines
on avoiding personal injury or product damage when installing your switch.
2. Install power supplies (page 32). Install power supplies if they are not already installed.
3. Install fan assemblies (page 33). Install fan assemblies if they are not already installed.
4. Power on the switch and check LEDs (page 34). Power-on the switch and check the LEDs for proper switch
operation.
5. Power off the switch (page 36). Remove power from the switch.
6. Mount the switch (page 36). The switch can be mounted in a 19-inch telco rack or in an equipment cabinet.
7. (Optional) Install transceivers (page 39). The switch has slots for installing SFP+/SFP28 and QSFP+/
QSFP28 transceivers. Depending on where you install the switch, it may be easier to install the transceivers
first. Transceivers can be hot swapped—they can be installed or removed while the switch is powered on.
8. Connect power to the switch (page 43). Once the switch is mounted, plug it into the main power source.
9. Connect a management console to the switch (page 44). You may want to modify the switch’s
configuration, so it can be managed using a Web browser or through an SSH or Telnet session. Configuration
changes can be made by using a console cable to connect a PC to the switch’s console port, or use the
included Bluetooth adapter to configure the switch from your mobile device.
10. Connect the network devices (page 45). Using the appropriate network cables, connect the network devices
to the switch ports.
At this point, your switch is fully installed. See the rest of this chapter if you need more detailed information on any
of these installation steps.

Installation precautions
To avoid personal injury or product damage when installing your switch, read the installation precautions and
guidelines below.
• Do not mount the switch on a wall, on or under a table, or on or under any other horizontal
surface.
• Mount devices installed in a rack or cabinet as low as possible. Put the heaviest devices at the
bottom and progressively lighter devices installed above.
• To prevent the rack or cabinet from becoming unstable and/or falling over, ensure that it is
adequately secured.
• Ensure the power source circuits are properly grounded. Then connect the switch to the power
source by using the power cord supplied with the switch.
• If your installation requires a different power cord than the one supplied with the switch and power
supply, be sure the cord is adequately sized for the switch’s current requirements. In addition, be
sure to use a power cord displaying the mark of the safety agency that defines the regulations for
power cords in your country. The mark is your assurance that the power cord can be used safely
with the switch and power supply.
• When installing the switch, the AC outlet should be near the switch and be easily accessible in
case the switch must be powered off.
• Do not install the switch in an environment where the operating ambient temperature exceeds its
specification. (See the Environmental information on page 60.)
• Ensure that the switch does not overload the power circuits, wiring, and over-current protection.
To determine the possibility of overloading the supply circuits, add the ampere ratings of all
devices installed on the same circuit as the switch. Then compare the total with the rating limit for
the circuit. The maximum ampere ratings are usually printed on the devices near the AC power
connectors.
• Ensure that the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for
cooling. For air flow direction, determine whether your switch has front-to-back or back-to-front
fans and power supply units.
• All power supplies and fan assemblies installed in a 8325 switch must have the same cooling air
flow direction (FB or BF).
• Never insert or remove a power supply while the power cord is connected. Verify that the cord has
been disconnected from the power supply before installation or removal.
If a power supply must be removed, and then reinstalled, wait at least 5 seconds before reinstallation.
Otherwise, damage to the switch may occur.
The power supply needs this time to bleed off any retained power.

1. Prepare the installation site
Cabling Infrastructure - Ensure the cabling infrastructure meets the necessary network specifications. See
chapter 7, Cabling and technology information for more information:
Installation Location - Before installing the switch, plan its location and orientation relative to other devices and
equipment:
• In the front of the switch, leave at least 3 inches (7.6 cm) of space for the twisted-pair and fiber-optic cabling.
• In the back of the switch, leave at least 3 inches (7.6 cm) of space for the power cord.
• On the sides of the switch, leave at least 3 inches (7.6 cm) for cooling.
Cooling air flow in Aruba 8325 switches is Front-to-Back (FB) or Back-to-Front (BF), depending on which power
supply and fan assembly options are installed. To reverse the cooling air flow direction in an 8325 switch, you must
replace the existing power supplies and fan assemblies with power supplies and fan assemblies having the
opposite air flow direction. All fans and power supplies installed in an 8325 switch must have the same air flow
direction. For specific model information see the “Overview” on page 9.
To avoid personal injury or product damage, review “Installation precautions” on page 31 before
beginning the installation.
2. Install power supplies

Skip this step if a power supply is already installed in the switch.
If a power supply is not already installed in the switch, install at least one power supply before continuing in this
guide. The Aruba 8325 switch uses any of the following power supplies:
• Aruba 8325 650W 100-240VAC FB PSU (JL632A)
• Aruba 8325 650W 100-240VAC BF PSU (JL633A)
A red-colored power supply release lever indicates a Front-to-Back (FB) air flow. A blue-colored
power supply release lever indicates a Back-to-Front (BF) air flow.
Figure 12: Installing a power supply

3. Install fan assemblies
Skip this step if all six fan slots are already populated with fan assemblies.
Use the following steps to install a fan assembly in any empty fan slot.
• The 48-port switches and the 32-port switches use different fan assemblies. Each fan assembly
type can only be installed in the correct switch model.
• Ensure that a replacement fan has the same airflow as other fans installed in the switch (FB or
BF).
• A red-colored fan handle indicates a Front-to-Back (FB) air flow. A blue-colored fan handle
indicates a Back-to-Front (BF) air flow.
1. Remove the new fan assembly from its packaging, being careful to not touch any of the circuitry on the board.
2. Insert the new fan assembly fully into the slot so that its face plate is flush with the back face of the switch. If
the switch is connected to an AC power source, the fan assembly should immediately start running.
3. For the 32-port switch fan assembly, engage the retaining screw and tighten it. Be sure to not over-tighten the
screw.
Figure 13: Installing a fan assembly

4. Power-on the switch and check LEDs
An Aruba 8325 switch does not contain a power on/off switch. It is turned on by connecting the AC power cord to
the switch and to an AC power source.
Figure 14: Connecting power to the switch
Check LEDs for proper switch operation.

Figure 15: Chassis LEDs for the Aruba 8325-48Y8C (JL624A and JL625A)
1 7
2
3
5
6
Table 23: Chassis LED labels for the Aruba 8325-48Y8C (JL624A and JL625A)
Label Description
1 SFP28 Port LEDs:

Off, unless a network cable is connected and the port is receiving link beat.
2 PS1 LED:
Green after power on, unless the power supply is in a fault state, or not receiving power.

Table 23: Chassis LED labels for the Aruba 8325-48Y8C (JL624A and JL625A) (Continued)
Label Description
3 PS2 LED:
4 Fan LED:
Green after power on, unless a fan on the back of the unit is in a fault state.
5 Global Status LED:

Green after power on, in the default configuration. Flashes amber during bootup.
6 UID LED
Locator or Unit Identification LED. Off after power on.
7 QSFP28 Port LEDs:

Off, unless a network cable is connected and the port is receiving link beat.
Figure 16: Chassis LEDs for the Aruba 8325-32C (JL626A and JL627A)
1
2
Label Description
1 UID LED
Locator or Unit Identification LED. Off after power on.
2 Global Status LED:

Green after power on, in the default configuration. Flashes amber during bootup.
3 PS1 LED:
4 PS2 LED:

Label Description
5 Fan LED:
Green after power on, unless a fan on the back of the unit is in a fault state.
5. Power off the switch

Remove the power cord from the switch and from the power source.
6. Mount the switch

Mounting an Aruba 8325 switch
The supported mounting options for the Aruba 8325 switch include:
• Two-post rack mount (JL482B; sold separately)
• Four-post rack mount (JL483B; sold separately)
See “Installation precautions” on page 31 before mounting your switch.
Two-post rack mount option:

The switch is designed to be mounted in any EIA-standard 19-inch telco rack or communication equipment cabinet
using the Aruba X472 2-Post Rack Kit (JL482B; sold separately).
The mounting brackets must only be attached for mid-mounting the switch in a two-post rack. Secure the rack in
accordance with the manufacturer’s safety guidelines.
For safe operation, please read the mounting precautions in “Installation precautions” on
page 31, before mounting a switch.
The 12-24 screws supplied with the switch are the correct threading for standard EIA/TIA open 19-
inch racks. If installing the switch in an equipment cabinet such as a server cabinet, use the clips
and screws that came with the cabinet in place of the 12-24 screws that are supplied with the switch.
Complete step 1, and plan which four holes you will be using in the cabinet and install all four clips.
Then proceed to step 2.
1. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included
eight 8-mm M4 screws.
The brackets must only be attached for mid-mounting the switch in a two-post rack. Ensure the holes in the
bracket are aligned with the correct holes in the switch, as per the diagram.

Figure 17: Attaching two-post mounting brackets to the switch
For safe, reliable installation, only use the screws provided in the accessory kit to attach the
mounting brackets to the switch.
2. Hold the switch with attached brackets up to the rack, move it vertically until rack holes line up with the bracket
holes, and then insert and tighten the four number 12-24 screws holding the brackets to the rack.
Figure 18: Mounting the switch in a two-post rack
Four-post rack mount option:

The Aruba 8325 switch can be mounted in four-post racks and cabinets by using the Aruba X474 4-Post Rack Kit
(JL483B); sold separately.
The JL483B Aruba X474 4-Post Rack Kit includes these items:
• two front-post brackets
• two rear-post brackets with adjustable ears
• twenty 8-mm M4 screws
• eight 5/8-inch number 12-24 screws
• two rear bracket ear position-locking screws

The brackets must only be attached for front-flush mounting the switch in a four-post rack. Secure the rack in
accordance with the manufacturer’s safety guidelines.
For safe operation, please read the mounting precautions in “Installation precautions” on
page 31, before mounting a switch.
The 12-24 screws supplied with the switch are the correct threading for standard EIA/TIA open 19-
inch racks. If installing the switch in an equipment cabinet such as a server cabinet, use the clips
and screws that came with the cabinet in place of the 12-24 screws that are supplied with the switch.
Complete step 1, and plan which holes you will be using in the cabinet and install all four clips. Then
proceed to step 2.
1. Use a #1 Phillips (cross-head) screwdriver and attach the front- and rear-post rack mount brackets to the
switch with the included 8-mm M4 screws.
Figure 19: Attaching four-post mounting brackets to the switch
For safe, reliable installation, only use the screws provided in the accessory kit to attach the
mounting brackets to the switch.
2. For the rear-post brackets, use an additional two 8-mm M4 screws to secure the bracket at the mid-point on
the side of the switch.
3. Hold the switch with attached brackets up to the rack, move it vertically until rack holes line up with the front-
post bracket holes, and then insert and tighten the four number 12-24 screws holding the brackets to the rack.

Figure 20: Mounting the switch in a four-post rack
4. Adjust the rear-post bracket ears to fit the depth of the rack.
5. Secure the rear-post brackets to the rack rear posts using four number 12-24 screws.
6. Lock the position of the rear-post bracket ears using the included position-locking screws.
Figure 21: Locking the position of rear-post brackets
7. Install transceivers
You can install or remove a transceiver from an SFP28/QSFP28 slot without having to power off the switch.
• The transceivers operate only at full duplex. Half duplex operation is not supported.
• Ensure the network cable is NOT connected when you install or remove a transceiver.

Use only supported genuine Aruba SFP/SFP+/SFP28/QSFP+/QSFP28 transceivers with your switch.
Non-Aruba transceivers are not supported, and their use may result in product malfunction. Should
you require additional transceivers, contact your Aruba sales representative or an authorized reseller.
For more transceiver support information for your switch model, see the ArubaOS-Switch and
ArubaOS-CX Transceiver Guide at https://asp.arubanetworks.com/downloads.
Hot swapping SFP/SFP+/SFP28/QSFP+/QSFP28 transceivers

Supported SFP/SFP+/SFP28/QSFP+/QSFP28 transceivers that you can install in your Aruba switch can be “hot
swapped”– removed and installed while the switch is receiving power. However, disconnect the network cables
from the SFP/SFP+/SFP28/QSFP+/QSFP28 transceivers before hot-swapping them.
When you replace an SFP/SFP+/SFP28/QSFP+/QSFP28 transceiver with another transceiver of a different type,
the switch may retain selected port-specific configuration settings that were configured for the replaced unit. Be
sure to validate or reconfigure port settings as required.
SFP/SFP+/SFP28/QSFP+/QSFP28 connections to devices with fixed speed/duplex configurations

When connecting a device to your switch port that contains a SFP/SFP+/SFP28/QSFP+/QSFP28 transceiver, the
speed and duplex settings of the switch port and the connected device must match. Otherwise, the device may not
link properly—you may not get a link. For some older network devices, the default speed/duplex settings may be
predefined (for example, to 1000 Mbps/Full Duplex), or otherwise set differently from the default configuration of
your switch. These setting differences may also apply to some older Hewlett Packard Enterprise devices. Because
of these default speed/duplex considerations, make sure that devices connected to your SFP/SFP+/SFP28/
QSFP+/QSFP28 ports are properly configured. At a minimum, make sure the configurations match.
Interface-Group operation
The SFP28 ports in the Aruba 8325-48Y8C switches (JL624A and JL625A) are organized into four groups of 12
ports each.
Figure 22: Front of the Aruba 8325-48Y8C (JL624A and JL625A) interface-groups
1 2 3 4
Table 25: Aruba 8325-48Y8C (JL624A and JL625A) interface-groups
Label Description
1 Interface-group 1 (ports 1 to 12)
The port speed configured for a given interface group determines the speed for all ports in that group. Any
mismatched interfaces in the group are disabled. For example, if interface group 1 is configured for 25G (the
default setting) and 10G transceivers are installed in ports 10 and 11, these two transceivers are in a mismatch

state and are disabled with the port error logged as “group speed mismatch.” The port LED will flash amber to
indicate an installation error was detected. All fault indications will flash in unison with the Global Status LED to
alert the user.
In the default switch configuration, all four interface-groups are configured to 25 Gbps. To configure the speed for
an interface-group to 10 Gbps, use the following command:
system interface-group <1|2|3|4> speed <10g|25g>
For example, to configure interface-group 1 for 10g, use this command:
8325(config)# system interface-group 1 speed 10g
Once entered, the switch will present the warning and required user response:
Changing the group speed will disable all member interfaces
that do not match the new speed.
Continue (y/n)? y
Only the 10G interface-group speed setting supports 1 Gbps transceivers. The 1 Gbps transceivers also require
the user to manually configure the port to 1000-full mode, an additional configuration to ensure IEEE-compliant
operation. For example, the following command is also required for 1G optics (do not use with 10G optics/DACs):
8325(config)# int 1/1/1 speed 1000-full
For more information, and to view or change the speed setting for a port group, see the Aruba 8325 Fundamentals
Guide for ArubaOS-CX 10.02 or later at https://asp.arubanetworks.com/downloads.
1GBase-T (J8177D) transceiver support restrictions in the 48-port 8325 switches

Beginning with software release 10.03, the Aruba 8325-48YBC switches also support 1GBase-T (J8177D)
transceivers in all top row and middle row ports. The bottom row ports do not support 1GBase-T (J8177D)
transceiver operation.
Figure 23: 1GBase-T transceiver support for the 48-port 8325 switches
Table 26: 1GBase-T transceiver support for the 48-port 8325 switches
Label Description
1 All top row ports support 1GBase-T (J8177D) transceivers.
2 All middle row ports support 1GBase-T (J8177D) transceivers.
3 Bottom row ports do not support 1GBase-T (J8177D) transceivers
Continued support for optical, DAC, or AOC products in other ports not occupied by a J8177D RJ45 transceiver.
If the switch detects a 1GBase-T (J8177D) transceiver in any bottom row port, the show interface brief
command will list an Incompatible interface for that port.
10GBase-T (JL563A) transceiver support restrictions in the 48-port 8325 switches

Beginning with software release 10.03, the Aruba 8325-48YBC switches also support 10GBase-T (JL563A)
transceivers in the following top row and middle row ports:

Figure 24: 10GBase-T transceiver support for the 48-port 8325 switches
Table 27: 10GBase-T transceiver support for the 48-port 8325 switches
Label Description
1 Top row ports 1, 4, 7, 10, 13, 16 support 10GBase-T (JL563A) transceivers.
2 Middle row ports 2, 5, 8, 11, 14, and 17 support 10GBase-T (JL563A) transceivers.
3 Bottom row ports do not support 10GBase-T (JL563A) transceivers
Continued support for optical, DAC, or AOC products in other ports not occupied by a J8177D RJ45 transceiver.
To enable use on ports 13-17, Interface-Group 2 must be set to 10G operation.
If the switch detects a 10GBase-T (JL563A) transceiver in any port that does not support it, the show interface
brief command will list an Incompatible interface for that port.
The switch does not support 10GBase-T (JL563A) transceivers in ports 3, 6, 9, 12, 15, 18, and 19
through 48. 10GBase-T support for ports 13-14, and 16-17 was added with software release 10.03.
Installing transceivers:
Hold the transceiver by its sides and gently insert it into either of the slots on the switch until it clicks into place.
When a transceiver is inserted the switch authenticates it. This can take 1-3 seconds, with the worst case being 5
seconds. If the transceiver is removed before the authentication completes a self test failure will be reported.
The fiber Aruba transceivers are Class 1 laser devices. Avoid direct eye exposure to the beam
coming from the transmit port.
Refer to Table 6, footnote 3, for ports that support 10GBase-T transceivers.

Figure 25: Installing a transceiver
Removing transceivers:
Depending on the transceiver, it will have either of three different release mechanisms:
• A plastic tab on the bottom of the transceiver
• A plastic collar around the transceiver
• A wire bail
To remove the transceivers that have the plastic tab or plastic collar, push the tab or collar toward the switch until
the transceiver releases from the switch (it will move outward slightly), then pull it from the slot.
To remove the transceivers that have the wire bail, lower the bail until it is approximately horizontal, and then using
the bail, pull the transceiver from the slot.
8. Connect the switch to a power source

1. If a power supply is not already installed in the switch, install at least one power supply. (See “2. Install power
supplies” on page 32.) The Aruba 8325 switch uses any of the following power supplies:
• Aruba 8325 650W 100-240VAC FB PSU (JL632A)
• Aruba 8325 650W 100-240VAC BF PSU (JL633A)
2. Plug the included power cord into the power supply’s power connector and into a nearby AC power source.

Figure 26: Connecting a power cord to the switch
3. Check the LEDs. See “Chassis LEDs on the front of the switch” on page 15.
One power supply provides power to operate the switch. Installing a second power supply can
provide power to the switch in case the initial power supply fails. If the power supplies are plugged
into different AC power sources, redundant power can be supplied in case of loss of one of the AC
power sources.
9. Set up for initial configuration

You can perform the initial configuration of the switch using one of these methods:
• Using Zero Touch Provisioning (ZTP): Use ZTP to configure a switch automatically from a remote server.
The switch must be in the factory default configuration. If ZTP is to be used, your network administrator or
installation site coordinator must provide an RJ-45 cable connected to the appropriate network. Connect the
switch to the network using the RJ-45 out-of-band management port and power on the switch (or power off,
then power on the switch). The ZTP operation is attempted for the first 10 minutes after the switch is powered
on. For more information about ZTP, see the Fundamentals Guide for your switch and software release.
• Using the Aruba CX mobile app: The Aruba CX mobile app can connect to the switch through the USB
Bluetooth adapter. For information about using the Aruba CX mobile app to configure the switch, see the
Fundamentals Guide for your switch and software release.
• Using an out-of-band serial console: Use a workstation configured with suitable VT-100 terminal emulation
software and connect the workstation to the switch’s RJ-45 Console Port. A DB9-to-RJ-45 console cable can
be ordered from HPE: JL448A, Aruba X2C2 RJ45 to DB9 Console Cable. For more information about this
method see “Initial configuration with an out-of-band serial connection” on page 47“.
• Using connections to the out-of-band dedicated management network: Use a workstation configured with
suitable VT-100 terminal emulation software and SSH software. Connect the workstation and the switch to the
same management network. Connect the switch to the network using the RJ-45 out-of-band management port.
For more information about using this method, see the Fundamentals Guide for your switch and software
release. The switch can simultaneously support one console session through the console port and multiple
network SSH sessions through the management port.

10. Connect the network cables
Connect the network cables, described under “Cabling Infrastructure” (1. Prepare the installation site), from the
network devices or your patch panels to the RJ-45 out-of-band management port on the switch or to any
transceivers you have installed in the switch.
Using the RJ-45 out-of-band management port

If you plan to manage the switch from a dedicated management network, connect an RJ-45 network cable from the
management network to the Mgmt port. The Mgmt port supports 10, 100, and 1000 Mbps connections.
To connect:
Push the RJ-45 plug into the RJ-45 port until the tab on the plug clicks into place. When power is on for the switch
and for the connected device, the Link LED for the port should light to confirm a powered-on device (for example,
an end node) is at the other end of the cable.
If the Link LED does not go on when the network cable is connected to the port, see “Diagnosing with the LEDs”
on page 54 in the Troubleshooting chapter.
To disconnect:
Press the small tab on the plug and pull the plug out of the port.
Figure 27: Connecting an RJ-45
Connecting cables to transceivers

If you have any transceivers installed in the switch, the type of network connections you will need to use depends
on the type of transceivers installed. See chapter 6, Cabling and technology information, for cabling information.
For transceiver ports, and in general for all the switch ports, a network cable from an active network device is
connected to the port. If the port LED does not come on when the network cable is connected to the port, see
“Diagnosing with the LEDs” on page 54 in the Troubleshooting chapter.

Figure 28: Connecting cable to a transceiver

Chapter 4
Initial configuration with an out-of-band serial connection
Terminal configuration
To connect a console to the switch, configure the PC terminal emulator as a DEC VT-100 (ANSI) terminal or use a
VT-100 terminal, and configure either one to operate with these settings:
• A baud rate of 115200.
• 8 data bits, 1 stop bit, no parity, and flow control set to off.
• For the Windows Terminal program, also disable (uncheck) the “Use Function, Arrow, and Ctrl Keys for
Windows” option.
• For the Hilgraeve HyperTerminal program, select the “Terminal keys” option for the “Function, arrow, and ctrl
keys act as” parameter.
If you want to operate the console using a different configuration, make sure you change the settings on both the
terminal and on the switch so they are compatible. Change the switch settings first, then change the terminal
settings, then reboot the switch and reestablish the console session.
Connect to console port

To connect a console to the switch, follow these steps:
1. Connect the PC or terminal to the switch’s Console Port using a console cable (JL448A; sold separately).
Figure 29: Connecting a console cable
2. Turn on the terminal or PC’s power and, if using a PC, start the PC terminal program.
3. Press [Enter] two or three times. When prompted to log in specify admin. When prompted for the password,
press [Enter]. (By default, no password is defined.)
You are placed into the manager command context, which is identified by the prompt: switch#. For example:
login as: admin
Password:
switch#
Chapter 4 Initial configuration with an out-of-band serial connection 47

If you want to continue with console management of the switch at this time, see the Aruba 8325 Fundamentals
Guide for ArubaOS-CX for initial configuration steps. For more detailed information, refer to the switch software
manuals for your switch provided at https://asp.arubanetworks.com/downloads.
Console cable pinouts

The Aruba X2C2 RJ45 to DB9 Console Cable (JL448A) has an RJ-45 plug on one end and a DB-9 female
connector on the other end. Table 28 describes the mapping of the RJ-45 to DB-9 pins.
Figure 30: RJ-45 to DB-9 pinouts
12345678
5 4 3 2 1
9 8 7 6
Table 28: Mapping of RJ-45 to DB-9
RJ-45 (Signal reference from Chassis) DB-9 (Signal reference from PC)
Reserved 1 8 CTS
Reserved 2 6 DSR
TXD 3 2 RXD
Reserved 4 1 DCD
GND 5 5 GND
RXD 6 3 TXD
Reserved 7 4 DTR
Reserved 8 7 RTS
– – 9 RI

Chapter 5
Replacing components
This chapter shows you how to remove and install the following components:
• Power supply
• Fan assembly
The power supplies and fan assemblies are hot swappable. You do not need to power off the switch before
installing or replacing a power supply or fan assembly.
The Aruba 8325 switch and its components are sensitive to static discharge. Use an antistatic wrist
strap and observe all static precautions when replacing components.
If a power supply must be removed and then reinstalled, wait at least 5 seconds before reinstallation.
Otherwise, damage to the switch may occur. The power supply needs this time to bleed off any
retained power.
Replacing a power supply

Never insert or remove a power supply while the power cord is connected. Verify that cord has been
disconnected from the power supply before installation or removal.
If the Aruba 8325 switch is configured with a redundant power supply, the switch will not suffer any loss of traffic or
performance if a power supply fails. To maintain system redundancy, a failed power supply should be replaced as
soon as possible. The PS1 or PS2 LED will be on amber, indicating a power supply has failed or is connected to
AC power but is not installed in a switch.
Two power supplies are available for use with the switch:
• Aruba 8325 650W 100-240VAC FB PSU (JL632A) (Front-to-Back cooling air flow)
• Aruba 8325 650W 100-240VAC BF PSU (JL633A) (Back-to-Front cooling air flow)
Cooling air flow (Front-to-Back or Back-to-Front) must be the same for both the power supply and the
fans installed in the switch.
To remove a power supply:

1. Remove the AC power cable from the failed power supply’s connector.
2. Grasping the handle of the failed power supply, release the locking mechanism by squeezing the latch handle
while removing the failed power supply.
Chapter 5 Replacing components 49

Figure 31: Replacing a failed power supply
Table 29: Replacing a failed power supply labels and descriptions
Label Description
1 Release latch
2 Power supply handle
3. Insert the new power supply. Slide it in all the way in until the locking mechanism clicks into place.
4. Connect the AC power cable to the new power supply’s connector.
Replacing a fan assembly

The Aruba 8325 switch is equipped with six field-replaceable, hot-swappable fan assemblies. The switch can
tolerate the failure of a single fan assembly while maintaining a safe operating temperature. To maintain system
redundancy, a failed fan assembly should be replaced as soon as possible. The Fan LED will be on amber,
indicating a fan assembly has failed.
The 8325-48Y8C and 8325-32C switches use different fan assemblies. Each fan assembly type can only be
installed in the correct switch model.
Two fan assemblies are available for use with the 8325-48Y8C:
• Aruba 8325-48Y8C Front-to-Back Fan (JL628A)
• Aruba 8325-48Y8C Back-to-Front Fan (JL629A)
Two fan assemblies are available for use with the 8325-32C:
• Aruba 8325-32C Front-to-Back Fan (JL630A)
• Aruba 8325-32C Back-to-Front Fan (JL631A)
The Aruba 8325 switch is not compatible with fan assemblies from other Aruba hardware platforms.
After removing a fan assembly, wait at least five seconds before inserting a replacement fan assembly
in the same slot.
Ensure that a replacement fan has the same airflow as other fans installed in the switch (FB or BF).
To replace a fan assembly:

1. Identify the failed fan assembly by its status LED. The fan assembly LED will be on red, or flashing red.
2. Remove the new fan assembly from its packaging, being careful to not touch any of the circuitry on the board.
3. Loosen the retaining screw on the fan assembly in the 8325-32C. For a fan assembly in the 8325-48Y8C, pull
the release latch on the inside of the fan assembly handle.
4. Grasping the handle of the failed fan assembly, pull it straight out to remove it from its slot.
5. Insert the new fan assembly fully into the slot so that its face plate is flush with the back face of the switch. If
the switch is connected to an AC power source, the fan assembly should immediately start running.
6. For the 8325-32C fan assembly, engage the retaining screw and tighten it. Be sure to not over-tighten the
screw.
Figure 32: Replacing a failed fan assembly
1
3
Table 30: Replacing a failed fan assembly labels and descriptions
Label Description
1 Fan assembly release latch
2 Fan assembly handle
3 Fan assembly retaining screw
Chapter 5 Replacing components 51

Chapter 6
Troubleshooting
This chapter describes how to troubleshoot your switch. This document describes troubleshooting mostly from a
hardware perspective. You can perform more in-depth troubleshooting on these devices using the software tools
available with the switches, including the full-featured console interface, the built-in web browser interface, and
IMC, the SNMP-based network management tool, or Aruba AirWave.
This chapter describes the following:
• Basic troubleshooting tips (see Basic troubleshooting tips)
• Diagnosing with the LEDs (see Diagnosing with the LEDs)
• Hardware diagnostic tests (see Hardware diagnostic tests)
• Downloading new software to the switch (see Downloading new switch software)
• Hewlett Packard Enterprise Customer Support Services (see Hewlett Packard Enterprise Customer
Support Services)
Basic troubleshooting tips

Most problems are caused by the following situations. Check for these items first when starting your
troubleshooting:
• Faulty or loose cables. Look for loose or obviously faulty connections. If the cables appear to be OK, make
sure the connections are snug. If that does not correct the problem, try a different cable.
• Non-standard cables. Non-standard and miswired cables may cause network collisions and other network
problems, and can seriously impair network performance. Use a new correctly-wired cable or compare your
cable to the cable in chapter 6, Cabling and technology information for pinouts and correct cable wiring.
• Transceiver type not supported by port. A 1GBase-T or 10GBase-T transceiver is installed in a port that
does not support the transceiver type. Only the first two rows of ports in Aruba 48YBC switches support
1GBase-T (J8177D) transceivers. Only the first six ports in rows 1 and 2 in Aruba 48YBC switches support
10GBase-T transceivers. For more information, see:
◦ “1GBase-T (J8177D) transceiver support restrictions in the 48-port 8325 switches” on page 41.
◦ “10GBase-T (JL563A) transceiver support restrictions in the 48-port 8325 switches” on page 41.
• Improper network topologies. It is important to make sure you have a valid network topology. Common
topology faults include excessive cable length and excessive repeater delays between end nodes. If you have
network problems after recent changes to the network, change back to the previous topology. If you no longer
experience the problems, the new topology is probably at fault.
In addition, you should make sure that your network topology contains no data path loops. Between any two
end nodes, there should be only one active cabling path at any time. Data path loops can cause broadcast
storms that will severely impact your network performance.
For your switch, if you want to build redundant paths between important nodes in your network to provide some
fault tolerance, you should enable Spanning Tree Protocol support on the switch. This ensures that only one
of the redundant paths is active at any time, thus avoiding data path loops. Spanning Tree can be enabled
through the switch console or the web browser interface. For more information on Spanning Tree, see the
Layer 2 Bridging Guide for your switch at https://asp.arubanetworks.com/downloads.
Chapter 6 Troubleshooting 53
Diagnosing with the LEDs
Table 31 shows LED patterns on the switch that indicate problem conditions for general switch operation
troubleshooting.
LED patterns for general switch troubleshooting

1. Check in the table for the LED pattern you see on your switch.
2. Refer to the corresponding diagnostic tip on the next few pages.
Table 31: LED error indicators
LED Pattern Indicating Problems
PS1/PS2 LEDs Global Status Fan Port LED Diagnostic Tip
Off with power – – – 1

cords plugged in
On amber1 Flashing amber – – 2
On green Flashing amber On amber – 3
On green Flashing amber – Flashing amber 4
On green On green – Off with cable 5

connected
On green On green – On, but the port is 6

not communicating
1
Either the PS1 or PS2 LED is on amber, but not both.
Diagnostic tips:
Table 32: Diagnostic tips
Tip Problem Solution
1 Both switch power Verify the AC power source works by plugging another device into the outlet.
supplies are not Or try plugging the power supplies into different outlets or try different power
plugged into an active cords.
AC power source.
If the problem is still not resolved, both power supplies may be faulty.
2 One of the power Verify the power cord is plugged into an active power source and to the power
supplies is not plugged supply. Make sure these connections are snug.
into an active AC power
Try power cycling the switch by unplugging and plugging the power cord back
source, or the power
into the other working power supply.
supply may have failed.
If the PS1/PS2 LED is still not on, verify the AC power source works by
plugging another device into the outlet. Or try plugging the switch into a
different outlet or try a different power cord.
If the power source and power cord are OK and this condition persists, the
switch power supply may have failed. Call your Hewlett Packard Enterprise-
authorized network reseller, or use the electronic support services from
Hewlett Packard Enterprise to get assistance.

3 One of the switch fan Try disconnecting power from the switch and wait a few moments. Then
assemblies may have reconnect the power to the switch and check the LEDs again. If the error
failed. indication reoccurs, one of the fan assemblies has failed. The switch may
continue to operate under this condition if the ambient temperature does not
exceed normal room temperature, but for best operation, the fan assembly
should be replaced. Call your Hewlett Packard Enterprise-authorized network
reseller, or use the electronic support services from Hewlett Packard
Enterprise to get assistance.
4 The network port for Try power cycling the switch. If the fault indication reoccurs:
which the LED is
• There may be a port configuration mismatch where a 10G transceiver is
flashing has
installed in a port configured for 25G, or the reverse.
experienced a self test
or initialization failure. • A 10GBase-T transceiver may be installed in an incompatible port. See
Table 6 for list of supported ports.
• The transceiver may have failed.
• The switch port may have failed.
Check the switch Event Log and show interface command output for
indication of the fault condition.
If the port has an SFP+/SFP28 transceiver or QSFP+/QSFP28 transceiver
installed, verify that the transceiver is supported by the switch. Unsupported or
unrecognized transceivers will be identified with this fault condition. For a list
of supported transceivers, see the ArubaOS-Switch and ArubaOS-CX
Transceiver Guide at https://asp.arubanetworks.com/downloads.
The transceivers are also tested when they are “hot-swapped”—installed or
changed while the switch is powered on.
To verify the port has failed, remove and reinstall the transceiver without
powering off the switch. If the port fault indication reoccurs, you will have to
replace the transceiver. Check the event log to see why the transceiver failed.
To get assistance, call your Hewlett Packard Enterprise-authorized network
reseller, or use the electronic support services from Hewlett Packard
Enterprise.
5 The network connection Try the following procedures:

is not working properly.
For the indicated port, verify that both ends of the cabling, at the switch and
the connected device, are connected properly.
Verify the connected device and switch are both powered on and operating
correctly.
Verify you have used the correct cable type for the connection:
For fiber-optic connections, verify the transmit port on the switch is connected
to the receive port on the connected device, and the switch receive port is
connected to the transmit port on the connected device.
The cable verification process must include all patch cables from any end
devices, including the switch, to any patch panels in the cabling path.
Verify the port has not been disabled through a switch configuration change.
You can use the console interface, or, if you have configured an IP address on
the switch, use the Web browser interface to determine the state of the port
and re-enable the port if necessary.
Verify the switch port configuration matches the configuration of the attached
device. For example, if the switch port is configured as “Full-duplex”, the port
on the attached device also MUST be configured as “Full-duplex”. If the
configurations don’t match, the results could be a very unreliable connection,
or no link at all.
If the other procedures don’t resolve the problem, try using a different port or a
different cable.
6 The port may be Use the switch console to see if the port is part of a dynamic trunk (through the
improperly configured, LACP feature) or to see if Spanning Tree is enabled on the switch, and to see
or the port may be in a if the port may have been put into a “blocking” state by those features. The
“blocking” state by the show lacp interfaces command displays the port status for the LACP
normal operation of the feature; the show spanning-tree command displays the port status for
Spanning Tree, LACP, Spanning Tree.
or IGMP features.
Also check the Port Status screen using the show interfaces command to
see if the port has been configured as “disabled”.
Other switch features that may affect the port operation include VLANs, IGMP,
and port group speed settings. Use the switch console to see how the port is
configured for these features. For more on port group speed settings, see
“Interface-Group operation” on page 40.
Ensure also, that the device at the other end of the connection is indicating a
good link to the switch. If it is not, the problem may be with the cabling
between the devices or the connectors on the cable.

Hardware diagnostic tests
Testing the switch by resetting it
If you believe the switch is not operating correctly, you can reset the switch to test its circuitry and operating code.
To reset a switch, either:
• unplug and plug in the power cord (power cycling)
• press the Reset button on the front of the switch
• reset the switch via the management console’s boot system command.
Power cycling the switch and pressing the Reset button both cause the switch to reset. These reset processes
also cause any network traffic counters to be reset to zero, and cause the System Up Time timer to reset to
zero.
Checking the switch LEDs

See “Diagnosing with the LEDs” on page 54 for information on interpreting the LED patterns.
Checking console messages

Useful diagnostic messages may be displayed on the console screen when the switch is reset. As described in
chapter 2 under step 6, connect a PC running a VT-100 terminal emulator program to the switch’s Console Port
and configure it to run at 115200 baud, and with the other terminal communication settings shown in “10. Connect
the network cables” on page 45. Then, when you reset the switch, note the messages that are displayed.
Additionally, you can check the switch event log, which can be accessed from the console using the show events
command.
Testing switch-to-device network communications

You can perform the following communication tests to verify the network is operating correctly between the switch
and any connected device that can respond correctly to the communication test.
• Link Test—a physical layer test that sends IEEE 802.2 test packets to any device identified by its MAC
address
• Ping Test—a network layer test used on IP networks that sends test packets to any device identified by its IP
address
These tests can be performed through the switch console interface from a terminal connected to the switch or
through a Telnet connection, or from the switch’s web browser interface.
Testing end-to-end network communications

Both the switch and the cabling can be tested by running an end-to-end communications test—a test that sends
known data from one network device to another through the switch. For example, if you have two PCs on the
network that have LAN adapters between which you can run a link-level test or Ping test through the switch, you
can use this test to verify that the entire communication path between the two PCs is functioning correctly. See
your LAN adapter documentation for more information on running a link test or Ping test.
Battery
This switch uses a lithium battery to maintain internal clock time across a reboot or power cycle. Do
not attempt to replace the battery. Return the switch to Aruba for battery replacement.
IMPORTANT: The only indicator of battery failure is the failure of the switch internal clock to keep the correct time
across a reboot or power cycle. No other switch operation is affected, and the switch does not require
battery power to function properly.
• To reset the switch internal clock, see the “Clock Commands” chapter or, for NTP (network time protocol)
server operation, the “NTP commands” chapter in the latest Command Line Interface Guide for your switch
software. To locate this guide, visit the Aruba Support Portal at https://asp.arubanetworks.com/downloads
and filter for Product Family, Product Series, and Document File Contents.
• If the battery fails and you want to replace it, contact your authorized Aruba representative for assistance.
Batteries are not customer-serviceable. Battery failures should only be referred to service personnel
authorized by Aruba.
For important safety, environmental, and regulatory information, see Safety and Compliance Information for Server,
Storage, Power, Networking, and Rack Products, available at
http://www.hpe.com/support/Safety-Compliance-EnterpriseProducts.
ATTENTION: ll y a danger d'explosion s'il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant.
ATTENTION: The battery supplied with this product may contain perchlorate material. Special handling may apply
in California and certain other states. See http://www.dtsc.ca.gov/hazardouswaste/ perchlorate Web site for
more information.
A risk of explosion exists if a battery is replaced by an incorrect type. Dispose of used batteries
according to the battery disposal regulations for your country or region.
Downloading new switch software

Software Updates can be downloaded to the switch through several methods. See “Accessing updates” on
page 68.
Hewlett Packard Enterprise Customer Support Services

If you are still having trouble with your product, see “Support and other resources” on page 67.

Chapter 7
Specifications
Switch specifications
Physical
Table 33: Physical specifications
Product Width Depth Height Weight
Aruba 8325-48Y8C FB 6 43.8 cm (17.26 in) 53.6 cm (21.1 in) 4.3 cm (1.69 in) 10 kg (22 lb)
F 2 PS Bdl (JL624A)
Aruba 8325-48Y8C BF 6
F 2 PS Bdl (JL625A)
Aruba 8325-32C FB 6 F 43.8 cm (17.26 in) 51.5 cm (20.28 in) 4.3 cm (1.69 in) 9.5 kg (21 lb)
2 PS Bdl (JL626A)
Aruba 8325-32C BF 6 F
2 PS Bdl (JL627A)
Electrical
Table 34: Electrical specifications
Product AC Voltage Maximum Frequency

current range
Aruba 8325 650W 100-240VAC FB PSU 100-240 volts 6A-3A 50-60 Hz

(JL632A)*
Aruba 8325 650W 100-240VAC BF PSU
(JL633A)*
* The power supply automatically adjusts to any voltage between 100-240 volts and either 50 or 60 Hz.
Power Consumption
Table 35: Power consumption specifications
Product Power consumption
Aruba 8325-48Y8C FB 6 F 2 PS Bdl (JL624A) Max: 550 W, 1877 BTU/hr

Idle: 209 W, 713 BTU/hr
Aruba 8325-48Y8C BF 6 F 2 PS Bdl (JL625A)
Aruba 8325-32C FB 6 F 2 PS Bdl (JL626A) Max: 550 W, 1877 BTU/hr

Idle: 143 W, 488 BTU/hr
Aruba 8325-32C BF 6 F 2 PS Bdl (JL627A)
Aruba 8325 650W 100-240VAC FB PSU (JL632A) Max: 650 W, 2218 BTU/hr
Aruba 8325 650W 100-240VAC BF PSU (JL633A)
Chapter 7 Specifications 59
MTBF
Table 36: MTBF specifications
Product MTBF
Aruba 8325-48Y8C FB 6 F 2 PS Bdl (JL624A) 183165.4 hours

Aruba 8325-48Y8C BF 6 F 2 PS Bdl (JL625A)
Aruba 8325-32C FB 6 F 2 PS Bdl (JL626A) 155725.2 hours

Aruba 8325-32C BF 6 F 2 PS Bdl (JL627A)
Environmental
Table 37: Environmental specifications
Aruba 8325 Switch Series (JL624A, JL625A, JL626A, and JL627A)
Operating Non-Operating
Temperature 0°C to 40°C (32°F to 104°F) up to 3.0 km -40°C to 70°C (-40°F to 158°F) up to 4.6 km
(10,000 ft) (15,000 ft)
Relative humidity 5% to 95% at 40°C (104°F) non- 5% to 95% at 65°C (149°F)

(non-condensing) condensing
Maximum altitude 3.0 km (10,000 ft)* 4.6 km (15,000 ft)
* The operating maximum altitude should not exceed that of any accessory being connected to any Aruba 8325
switch.
Acoustics
Table 38: Acoustic specifications
Switch Model Acoustics
Aruba 8325-48Y8C FB 6 F 2 PS Bdl (JL624A) Sound Pressure (LpAm) (Bystander) 90.8 dB

Aruba 8325-48Y8C BF 6 F 2 PS Bdl (JL625A) Sound Pressure (LpAm) (Bystander) 88.3 dB
Aruba 8325-32C FB 6 F 2 PS Bdl (JL626A) Sound Pressure (LpAm) (Bystander) 87.4 dB

Aruba 8325-32C BF 6 F 2 PS Bdl (JL627A) Sound Pressure (LpAm) (Bystander) 85.1 dB
RoHS
EN 50581:2012

Standards
Table 39: Technology standards and safety compliance
Laser safety information
Technology Compatible with these IEEE EN/IEC standard Lasers

standards compliance
1000BASE-T IEEE 802.3ab 1000BASE-T – –
1000BASE-SX IEEE 802.3z 1000BASE-SX EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
1000BASE-LX IEEE 802.3z 1000BASE-LX EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
1000BASE-LH (not an IEEE standard) EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
10GBASE-T IEEE 802.3an 10GBASE-T – –
10GBASE-SR IEEE 802.3ae 10GBASE-SR EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
10GBASE-LR IEEE 802.3ae 10GBASE-LR EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
10GBASE-ER IEEE 802.3ae 10GBASE-ER EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
25GBASE-SR IEEE 802.3by 25GBASE-SR EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
25GBASE-eSR (not an IEEE standard) EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
25GBASE-LR IEEE 802.3cc 25GBASE-LR EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
40GBASE-SR4 IEEE 802.3ba 40GBASE-SR4 EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
40GBASE-eSR4 (not an IEEE standard) EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
40GBASE-LR4 IEEE 802.3ba 40GBASE-LR4 EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
40GBASE-ER4 IEEE 802.3bm 40GBASE-ER4 EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
Chapter 7 Specifications 61
Table 39: Technology standards and safety compliance (Continued)
Laser safety information
Technology Compatible with these IEEE EN/IEC standard Lasers

standards compliance
40GBASE-Bidi (not an IEEE standard) EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
100GBASE-SR4 IEEE 802.3bm 100GBASE-SR4 EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1
100GBASE-LR4 IEEE 802.3ba 100GBASE-LR4 EN/IEC 60825 Class 1 Laser Product

Laser Klasse 1

Chapter 8
Cabling and technology information
This chapter includes switch connector information and network cable information for cables that should be used
with the Hewlett Packard Enterprise switches.
Incorrectly wired cabling is a common cause of problems for LAN communications. Hewlett Packard
Enterprise recommends that you work with a qualified LAN cable installer for assistance with your
cabling requirements.
Cabling specifications
Table 40: Cabling specifications
Twisted-pair copper 1000 Mbps Operation Category 5, 100-ohm 4-pair UTP or STP cable, complying
with IEEE 802.3ab 1000BASE-T specifications—Category 5e
or better is recommended. See “Note on 1000BASE-T
cable requirements” on page 63.
10 Gbps Operation Category 6 or 6A, 100-ohm 4-pair UTP cable, or Category 6A

or 7, 100-ohm 4-pair STP cable, complying with IEEE
802.3an 10GBASE-T specifications.
See Note on 10GBASE-T cable requirements below, and
see “Technology distance specifications” on page 64 for
distances supported with each cable type.
CAT6A F/FTP, S/FTP, SF/FTP highly recommended in noisy
environments. Refer to Aruba
Support_Advisory_JL563A_10GBaseT_APSC-RS20180403-
01 for more information.
Twinaxial copper Direct attach cables One-piece devices consisting of a cable with SFP+
connectors permanently attached to each end, complying
with SFF 8431 SFP+ specifications.
Multimode fiber 62.5/125 m or 50/125 m (core/cladding) diameter, low

metal content, graded index fiber-optic cables, complying
with the ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a
standards respectively.
Single mode fiber 9/125 m (core/cladding) diameter, low metal content fiber-
optic cables, complying with the ITU-T G.652 and
ISO/IEC 793-2 Type B1 standards.
Note on 1000BASE-T cable requirements

The Category 5 networking cables that work for 100BASE-TX connections should also work for 1000BASE-T, as
long as all four-pairs are connected. But, for the most robust connections, you should use cabling that complies
with the Category 5e specifications, as described in Addendum 5 to the TIA-568-A standard (ANSI/TIA/EIA-568-A-
5).
Because of the increased speed provided by 1000BASE-T (Gigabit-T), network cable quality is more important
than for either 10BASE-T or 100BASE-TX. Cabling plants being used to carry 1000BASE-T networking must
Chapter 8 Cabling and technology information 63

comply with the IEEE 802.3ab standards. In particular, the cabling must pass tests for Attenuation, Near-End
Crosstalk (NEXT), and Far-End Crosstalk (FEXT). Additionally, unlike the cables for 100BASE-TX, the 1000BASE-
T cables must pass tests for Equal-Level Far-End Crosstalk (ELFEXT) and Return Loss.
When testing your cabling, be sure to include the patch cables that connect the switch and other end devices to the
patch panels on your site. The patch cables are frequently overlooked when testing cable and they must also
comply with the cabling standards.
Note on 10GBASE-T cable requirements
The Category 6 networking cables that work for 1000BASE-T connections may work for 10GBASE-T, as long as
the distance is less than 30m and the cable installation has been tested for compliance to IEEE requirements. But,
for the most robust connections, you should use cabling that complies with the Category 6A or Category 7
specifications, as described in the TIA-568-C (ANSI/TIA-568-C.2) and ISO/IEC 11801 standards. 10GBASE-T is a
sophisticated technology that relies upon high quality cable installations. It is sensitive to Alien Near End Crosstalk
(ANEXT) which can arrive upon the cable due to cables placed in close proximity to the data cables. It is
recommended that cable dressing be done carefully and in compliance with recommendations in the TIA TSB-
155A.
Like 1000BASE-T, 10GBASE-T requires testing of all the crosstalk and return loss parameters described above,
and also ANEXT.
In addition to ANEXT, 10GBASE-T is more sensitive to external electrical noise in the environment. It is
recommended that radio transmitters and other sources of high frequency continuous wave radio frequency be
kept away from LAN cables.
When testing your cabling, be sure to include the patch cables that connect the switch and other end devices to the
patch panels on your site. The patch cables are frequently overlooked when testing cable and they must also
comply with the cabling standards. For 10GBASE-T, Category 6 patch cables are sensitive to movement once link
has been established, and could cause link to drop if moved. Therefore, Hewlett Packard Enterprise recommends
using Category 6A patch cables, or using cable management options to tie down (dress) the Category 6 patch
cables so they cannot move.
For Conducted and Radiated Immunity in accordance with EN55024, the Aruba switch is limited to Performance
Criteria A with shielded cables (CAT6A).
Technology distance specifications

Table 41: Technology distance specifications
Technology Supported cable type Multimode fiber Supported distances

modal bandwidth
1000BASE-T twisted-pair copper N/A up to 100 meters
1000BASE-SX multimode fiber 160 MHz*km 2 - 220 meters

200 MHz*km 2 - 275 meters
1000BASE-LX single mode fiber N/A 2 - 10,000 meters
1000BASE-LH single mode fiber N/A 2 - 70,000 meters2
10GBASE-T 1 twisted-pair copper N/A Cat 6A unshielded - up to 100 meters

Cat 6A shielded - up to 100 meters
Cat 7 shielded - up to 100 meters

Table 41: Technology distance specifications (Continued)
Technology Supported cable type Multimode fiber Supported distances

modal bandwidth
10GBASE-CR twinaxial copper N/A (various lengths offered)

(Direct Attach)
10GBASE-SR multimode fiber 160 MHz*km 2 - 26 meters

10GBASE-LR single mode fiber N/A 2 - 10,000 meters
10GBASE-ER single mode fiber N/A 2 - 40,000 meters2
25GBASE-CR twinaxial copper N/A (various lengths offered)
25GBASE-SR multimode fiber 1500 MHz*km 2 - 70 meters

25GBASE-eSR multimode fiber 1500 MHz*km 2 - 200 meters

25GBASE-LR single mode fiber N/A 2 - 10,000 meters
40GBASE-CR4 twinaxial copper N/A (various lengths offered)
40GBASE-SR4 multimode fiber 1500 MHz*km 2 - 100 meters

40GBASE-eSR4 multimode fiber 1500 MHz*km 2 - 330 meters

40GBASE-LR4 single mode fiber N/A 2 - 10,000 meters
40GBASE-ER4 single mode fiber N/A 2 - 40,000 meters2
40GBASE-BiDi multimode fiber 1500 MHz*km 2 - 100 meters

100GBASE-CR4 twinaxial copper N/A (various lengths offered)
100GBASE-SR4 multimode fiber 1500 MHz*km 2 - 100 meters

100GBASE-LR4 single mode fiber N/A 2 - 10,000 meters

1 Refer to Table 6, footnote 3, for ports that support 10GBase-T transceivers.
2
For distances less than 20km, a 10dB attenuator must be used. For distances between 20km and 40km, a
5dB attenuator must be used. Attenuators can be purchased from most cable vendors.
Chapter 8 Cabling and technology information 65

Chapter 9
Support and other resources
Accessing Hewlett Packard Enterprise support

• For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide Support website:
www.hpe.com/assistance
• To access documentation and support services, go to the Hewlett Packard Enterprise Support Center website:
www.hpe.com/support/hpesc
Information to collect
• Technical support registration number (if applicable)
• Product name, model or version, and serial number
• Operating system name and version
• Firmware version
• Error messages
• Product-specific reports and logs
• Add-on products or components
• Third-party products or components
Hewlett Packard Enterprise offers support 24 hours a day, seven days a week through the use of a number of
automated electronic services. Hewlett Packard Enterprise provides up-to-date customer care, support and
warranty information at http://www.hpe.com/networking/support. Additionally, your Hewlett Packard Enterprise
authorized network reseller can provide you with assistance, both with services that they offer and with services
offered by Hewlett Packard Enterprise.
Before calling support

To make most efficient use of the support process, you must retrieve the following information before calling your
authorized network reseller or Hewlett Packard Enterprise Support.
Table 42: Information before calling support
Information item Information location
• Product identification, including SFP/SFP+/ The front of the switch and on labels on the SFP/
SFP28/QSFP+/QSFP28 transceivers SFP+/SFP28/QSFP+/QSFP28 transceivers
• Details about the switch’s status including the Switch console: show tech command
software (OS) version, a copy of the switch
configuration, a copy of the switch Event Log,
and a copy of the switch status and counters
information
• Copy of your network topology map, including Your network records

network addresses assigned to the relevant
devices
Chapter 9 Support and other resources 67

Accessing updates
• To download product updates, go to either of the following:
◦ Hewlett Packard Enterprise Support Center's Subscription Service/Support Alerts page:
www.hpe.com/support/e-updates
◦ To view and update your entitlements, and to link your contracts, Care Packs, and warranties with your
profile, go to the Hewlett Packard Enterprise Support Center More Information on Access to HP
Support Materials page:
www.hpe.com/support/AccessToSupportMaterials
IMPORTANT: Access to some updates might require product entitlement when accessed through
the Hewlett Packard Enterprise Support Center. You must have a Hewlett Packard Enterprise
Passport set up with relevant entitlements.
• Software updates can be downloaded to the switch through several methods. Switch software updates are
available at http://www.hpe.com/networking/software.
• For information on methods for downloading and installing software, see the appropriate manuals for your
switch in the Aruba Support Portal at https://asp.arubanetworks.com/downloads.
Websites
Aruba Support Portal
https://asp.arubanetworks.com/downloads
Hewlett Packard Enterprise Networking Software
www.hpe.com/networking/software
Hewlett Packard Enterprise Networking website
www.hpe.com/info/networking
Hewlett Packard Enterprise My Networking website
www.hpe.com/networking/support
Hewlett Packard Enterprise My Networking Portal
www.hpe.com/networking/mynetworking
Hewlett Packard Enterprise Networking Warranty
www.hpe.com/networking/warranty
Customer self repair

Hewlett Packard Enterprise customer self repair (CSR) programs allow you to repair your product. If a CSR part
needs to be replaced, it will be shipped directly to you so that you can install it at your convenience. Some parts do
not qualify for CSR. Your Hewlett Packard Enterprise authorized service provider will determine whether a repair
can be accomplished by CSR.
For more information about CSR, contact your local service provider or go to the CSR website:
www.hpe.com/support/selfrepair

Remote support
Remote support is available with supported devices as part of your warranty, Care Pack Service, or contractual
support agreement. It provides intelligent event diagnosis, and automatic, secure submission of hardware event
notifications to Hewlett Packard Enterprise, which will initiate a fast and accurate resolution based on your
product’s service level. Hewlett Packard Enterprise strongly recommends that you register your device for remote
support.
For more information and device support details, go to the following website:
www.hpe.com/info/insightremotesupport/docs
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us improve
the documentation, send any errors, suggestions, or comments to DocumentationFeedback
([email protected]). When submitting your feedback, include the document title, part number, edition, and
publication date located on the front cover of the document. For online help content, include the product name,
product version, help edition, and publication date located on the legal notices page.
Chapter 9 Support and other resources 69

Aruba 8325 Switch SeriesInstallation and Getting Started Guide

Uploaded by

Copyright:

Available Formats

Aruba 8325 Switch SeriesInstallation and Getting Started Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aruba 8325 Switch SeriesInstallation and Getting Started Guide

Uploaded by

Copyright:

Available Formats

Aruba 8325 Switch Series

Installation and Getting Started Guide

Part Number: 5200-5297a

Chapter 1 About this document ........................................................................ 7

Chapter 2 Introducing the Aruba 8325 Switch ................................................. 9

Chapter 3 Installing the switch ........................................................................ 29

Chapter 4 Initial configuration with an out-of-band serial connection ........ 47

Chapter 5 Replacing components................................................................... 49

Chapter 6 Troubleshooting .............................................................................. 53

Chapter 7 Specifications .................................................................................. 59

Chapter 8 Cabling and technology information............................................. 63

Chapter 9 Support and other resources ......................................................... 67

4 Aruba 8325 Switch Installation and Getting Started Guide

This document is intended for network administrators and support personnel.

Chapter 1 About this document 7

Table 1: Switches described in this manual

Table 2: Accessories list

Power supplies* Aruba 8325 650W 100-240VAC FB PSU (JL632A)

Fan assemblies* Aruba 8325-48Y8C Front-to-Back Fan (JL628A)

Chassis Aruba 8325-48Y8C 48p 25G 8p 100G Swch (JL635A)

* Field replaceable units (FRUs).

Chapter 2 Introducing the Aruba 8325 Switch 9

Front of the switch

Table 3: Front of the Aruba 8325-48Y8C (JL624A and JL625A)

2 SFP28 ports (these ports support SFP/SFP+/SFP28 transceivers)

4 QSFP28 port LEDs

5 RJ-45 10/100/1000Base-T Out-of-Band Management Port (OOBM)

6 RJ-45 serial console port

10 Aruba 8325 Switch Installation and Getting Started Guide

8 Micro-USB serial console port

9 USB-A Port for file management and HPE-Aruba Accessories

10 QSFP28 ports (these ports support QSFP+ and QSFP28 transceivers)

8325-32C JL626A and JL627A switches

Table 4: Front of the Aruba 8325-32C (JL626A and JL627A)

2 QSFP28 ports (these ports support QSFP+ and QSFP28 transceivers)

3 QSFP28 port LEDs

4 RJ-45 10/100/1000Base-T Out-of-Band Management (OOBM) Port

5 USB-A Port for file management and HPE-Aruba Accessories

7 RJ-45 serial console port

Chapter 2 Introducing the Aruba 8325 Switch 11

Product Model name SFP28 ports1, 3 QSFP28 ports2

JL624A and Aruba 8325-48Y8C FB 6 F 2 PS Bdl 48 8

JL626A and Aruba 8325-32C FB 6 F 2 PS Bdl – 32

This product also supports optional network connectivity:

Table 6: Optional network connectivity, speeds, and technologies

Transceiver form-factor and connector1

Speed Technology Cabling SFP ("mini- SFP+ SFP28 QSFP+ QSFP28

1 Gbps 1-Gig T2 Copper – – – – –

1-Gig LH Fiber (single LC – – – –

10 Gbps 10-Gig Copper – – – – –

10-Gig AOC Fiber – – – – –

10-Gig BT3, 4 Copper – – – – –

10-Gig SR Fiber – LC6 – – –

10-Gig LR Fiber (single – LC – – –

10-Gig ER Fiber (single – LC – – –

12 Aruba 8325 Switch Installation and Getting Started Guide

Transceiver form-factor and connector1

Speed Technology Cabling SFP ("mini- SFP+ SFP28 QSFP+ QSFP28

25 Gbps 25-Gig Copper – – – – –

25-Gig AOC Fiber – – – – –