Upload 1567785988 ROHN SSV

SS SELF-SUPPORTING TOWERS
G SERIES
SELF-SUPPORTING TYPICAL
G-SERIES
SELF-SUPPORTING
GENERAL USE
The self-supporting G-Series towers offer an easy,

low-cost solution to get light weight antennas in
the air quickly. By using the G-Series tower as a
self-supporting structure, you minimize land area
usage. They are functional in a wide variety of
wind speeds, with and without ice. See ROHN’s
standard design to help identify the right struc-
ture for your project. Theses are the same sturdy,
robust tower sections that ROHN has fabricated
for years. Each larger model allows for more
loading capacity.
FEATURES
• Completely hot-dip galvanized after fabrica-

tion to provide absolute corrosion protection.
• Cross bracing is formed by a continuous solid
rod bracing fashioned into a zig-zag pattern for
strength.
• Pre-engineered loading charts meet varying
individual specs and site conditions.
• Typical uses include small dishes, broadband,
security and two-way communication.
Typical Self-Supporting Typical Self-Supporting

25G, 45G and 55G Tower 65G Tower
25GSSB
112 Phone (309) 697-4400 • Fax (309) 697-5612 • www.rohnnet.com • The Industry Standard
© 2009 ROHN PRODUCTS LLC
SELF-SUPPORTING TOWERS SS
G SERIES
A L LO WA B L E A N T E N N A A R E A S ( S Q . F T. )
70 MPH - No Ice
25G 45G 55G 65G
90 MPH 80 MPH 70 MPH
Height FT. 2 Part No. FT.2 Part No. FT.2 Part No. FT. 2 Part No.
10’ 19.7 25SS010 42.5 45SS010 75.0 55SS010 175.9 65SS010
20’ 14.2 25SS020 22.0 45SS020 43.0 55SS020 117.0 65SS020
30’ 6.4 25SS030 12.0 45SS030 26.0 55SS030 76.2 65SS030
35‘ 3.6 25SS035 8.7 45SS035 21.9 55SS035 61.2 65SS035
40’ 1.5 25SS040 5.1 45SS040 15.0 55SS040 48.8 65SS040
45‘ 2.3 45SS045 11.4 55SS045 39.0 65SS045
50’ 6.5 55SS050 29.3 65SS050
55‘ 4.0 55SS055 24.4 65SS055
60’ 0.8 55SS060 18.4 65SS060
70’ 8.7 65SS070
80’ 0.9 65SS080
80 MPH - No Ice
NO ICE
25G 45G 55G 65G
10’ 14.3 25SS010 30.0 45SS010 57.0 55SS010 133.0 65SS010
20’ 9.0 25SS020 16.0 45SS020 30.0 55SS020 85.0 65SS020
30’ 3.7 25SS030 7.5 45SS030 17.0 55SS030 55.8 65SS030
35‘ 1.4 25SS035 4.7 45SS035 14.5 55SS035 44.0 65SS035
40’ 1.4 45SS040 8.0 55SS040 34.1 65SS040
45‘ 5.9 55SS045 26.2 65SS045
50’ 1.5 55SS050 19.7 65SS050
55‘ 14.5 65SS055
60’ 9.4 65SS060
70’ 1.3 65SS070
90 MPH - No Ice
25G 45G 55G 65G
Height FT. 2 Part No. FT. Part No. FT.2
2 Part No. FT. 2 Part No.
10’ 10.5 25SS010 25.0 45SS010 45.0 55SS010 103.6 65SS010
20’ 6.9 25SS020 11.0 45SS020 23.0 55SS020 65.0 65SS020
30’ 1.7 25SS030 4.0 45SS030 12.0 55SS030 40.0 65SS030
35‘ 1.9 45SS035 9.4 55SS035 32.2 65SS035
40’ 4.0 55SS040 24.1 65SS040
45‘ 2.2 55SS045 17.7 65SS045
50’ 14.5 65SS050
55‘ 7.7 65SS055
60’ 3.3 65SS060
Phone (309) 697-4400 • Fax (309) 697-5612 • www.rohnnet.com • The Industry Standard
113
G SERIES
A L LO WA B L E A N T E N N A A R E A S ( S Q . F T. )
70 MPH - 1/2” Radial Ice

25G 45G 55G 65G
90 MPH 80 MPH 70 MPH
10’ 22.8 25SS010 55.0 45SS010 99.0 55SS010 231.4 65SS010
20’ 14.4 25SS020 25.0 45SS020 52.0 55SS020 150.0 65SS020
30’ 2.5 25SS030 9.0 45SS030 27.0 55SS030 95.0 65SS030
35‘ 0.0 25SS035 4.7 45SS035 22.2 55SS035 76.4 65SS035
40’ 0.0 25SS040 0.0 45SS040 8.0 55SS040 59.1 65SS040
45‘ 5.5 55SS045 45.7 65SS045
1/2” RADIAL ICE

50’ 0.0 55SS050 33.5 65SS050
55‘ 0.0 55SS055 25.0 65SS055
60’ 0.0 55SS060 16.0 65SS060
70’ 1.9 65SS070
80’ 0.0 65SS080

25G 45G 55G 65G
10’ 15.5 25SS010 40.0 45SS010 74.0 55SS010 174.3 65SS010
20’ 7.1 25SS020 16.0 45SS020 35.0 55SS020 105.0 65SS020
30’ 0.0 25SS030 2.7 45SS030 16.0 55SS030 65.0 65SS030
35‘ 0.0 25SS035 0.0 45SS035 12.4 55SS035 53.4 65SS035
40’ 0.0 45SS040 2.5 55SS040 39.0 65SS040
45‘ 0.0 55SS045 28.8 65SS045
50’ 0.0 55SS050 19.1 65SS050
55‘ 11.4 65SS055
60’ 4.1 65SS060
70’ 0.0 65SS070

25G 45G 55G 65G
10’ 10.5 25SS010 30.0 45SS010 57.0 55SS010 135.0 65SS010
20’ 2.1 25SS020 10.0 45SS020 26.0 55SS020 85.0 65SS020
30’ 0.0 25SS030 0.0 45SS030 9.0 55SS030 49.0 65SS030
35‘ 0.0 45SS035 5.7 55SS035 37.7 65SS035
40’ 0.0 55SS040 25.0 65SS040
45‘ 0.0 55SS045 17.2 65SS045
50’ 8.0 65SS050
55‘ 2.6 65SS055
60’ 0.0 65SS060
DESIGN NOTES
1. Tower designs are in accordance with approved national standard ANSI/EIA-222-F.

2. All towers must have “fixed” bases. Pinned bases may not be used.
3. Designs assume transmission lines symmetrically placed as follows:
25G Tower - One 5/8” Line on each face (Total =3)
45G Tower - One 7/8” Line on each face (Total = 3 @ 7/8” & 3 @ 1/2”)
55G & 65G Towers - Two 7/8” Lines on each face (Total =6)
4. Antennas and mounts assumed symmetrically placed at tower apex.
5. Allowable antenna areas assume all round antenna members.
6. Allowable flat-plate antenna areas, based on EIA RS-222-C, may be obtained by multiplying areas shown by 0.6.
7. For wind speeds with ice, the areas shown include 1/2” radial ice. Antenna areas without ice must not exceed the
areas shown for the no ice condition.
F O U N D AT I O N I N F O R M AT I O N
CL
Tower Axis &

Center of Pad
CL
Overturning Max. Allow Concrete

Tower Moment Shear Width Required
(FT. LBS.) (LBS.) (Cu. Yds.)
W
25G 6,800 700 4’ - 0” 2.4
(Square)
45G 12,800 1,600 5’ - 3” 4.1
PLAN VIEW
55G 22,900 1,600 6’ - 0” 5.3

Tower Section or
Short Base Section 65G 49,600 3,800 8.9
7’ - 9”
Ground 6”
4’
6” 2” Min.
Compacted Sand & Gravel

#7 Bars 12” Drainage Bed
on Center
Each Way
ELEVATION VIEW
115
CAMERA TOWERS
SELF-SUPPORTING TYPICAL
90 MPH - 1/2” ICE
Tower Over-turning Concrete Req’d

Height Moment (ft. lbs.) Width (cu. yds)
10’ 4,730 4’-6” 3.0
20’ 12,100 4‘-9” 3.4
30’ 21,400 5’9” 4.9
40’ 32,600 6‘-6” 6.3

50’ 46,900 7’-3” 7.8
Maximum Load at Top

EPA (ft.2 )
No Ice Ice
14.5 8.0
50’
40’
30’
20’
10’
65SS010CT 65SS020CT 65SS030CT 65SS040CT 65SS050CT

290 lbs. 490 lbs. 685 lbs. 860 lbs. 1055 lbs.
4’-6” 4’-9” 5’-9” 6’-6” 7’-3”
CAMERA TOWERS
S H O R T B A S E P I E R D E TA I L
W/2 6”
2”
CL Tower Axis
W/2
1’ - 2”
“W” 1’ - 9”
CL 3’ - 6”
Square
}
2’-1/4”
#7 Horizontal Bars
6” of Compacted Sand 12” O.C. Each Way
& Gravel for Drainage (Top & Bottom)
ACCESSORIES
SAFETY CABLE SYSTEM

ORDERING INFORMATION
TOWER PART
HEIGHT NUMBER
50’ TT05065
CLIMBING HARNESS
TTFBH-4D SAFETY CABLE
4D RING HARNESS SLIDER
ANTI-CLIMB PANELS TTFBH-C/P TT-WG-500
VW915A PROFESSIONAL HARNESS WIRE ROPE GRAB
GENERAL NOTES
1. Tower designs are in accordance with approved national standard ANSI/TIA/EIA-222-F.
2. All towers must have “fixed bases”. Pinned bases may not be used.
3. Tower design assumes one 3/4” conduit on tower face.
4. Camera and mount assumed symmetrically placed at tower top.
5. Do not install or dismantle towers within falling distance of electrical and/or telephone lines.
6. Tower erection and dismantling must be done by qualified and experienced personnel.
7. Install warning plate in highly visible location.
8. Where applicable, all camera installations must be grounded in accordance with local and national codes.
9. Tower design assumes work platform mounted 5’ below tower top.
10. Climber Safety device is recommended for climbing the tower.
11. Anti-climb device and/or work platform may be supplied as an option.
12. Pal nuts are provided for all tower and anchor bolts.
117
SS SELF-SUPPORTING TOWERS - RSL
*Top Mount RSL
RSL
(15) SLDG10 (15) SLDG09 (15) SLDG08 (15) SLDG07 (15) SLDG06 (15) SLDG05 (15) SLDG04 (15) SLDG03 (15) SLDG02 (15) SLDG01
18”
RSL1
(1) SLLE01
(2) SLLE02
10’ - 0”
RSL1
21”
(1) SLLE03
(2) SLLE04
RSL2
10’ - 0”
RSL2
GENERAL USE
25”
(1) SLLE05
(2) SLLE06
The ROHN RSL is a light weight self-supporting tower

10’ - 0”
RSL3
RSL3
designed for use in broadband, public safety

and security applications. The RSL reaches above
line-of-site obstacles such as tree tops, hilly terrain
28”
(1) SLLE07
(2) SLLE08
and buildings. If your site is remote or rugged, the

10’ - 0”
RSL4
RSL is shipped knocked down to reduce shipping,

RSL4
cost and time.

(1) SLLE09
(2) SLLE10
32”
10’ - 0”
RSL5
RSL5
FEATURES
(1) SLLE11
(2) SLLE12
•Available in heights from 20’ - 100’

10’ - 0”
35”
RSL6
• High strength angle legs

• Aerodynamic tubular bracing
RSL6
• Easy to transport and assemble

• Ships in 10’ sections or knocked-down
(1) SLLE13
(2) SLLE14
10’ - 0”
• Tower material is hot-dip galvanizied

RSL7
38”
* Optional items are available and may
RSL7
be ordered separately:
(1) SLLE15
(2) SLLE16
- Step bolts
10’ - 0”
RSL8
42” - Safety device

- Top mount kits
- Anti-Climb Panels (for #10 section)
RSL8
(1) SLLE17
(2) SLLE18
- Dish Mount
10’ - 0”
RSL9
- Side Arm
45”
RSL9
(1) SLLE19
(2) SLLE20
10’ - 0”
RSL10
49”
Section P/N
Braces P/N
RSL10
Legs P/N
Length
52”
*Base Section
SELF-SUPPORTING TOWERS - RSL SS
20’ Towers
18” 25” 32” 38” 45”
21” 28” 35” 42” 49”
25” 32” 38” 45” 52”
Kit: RSL020L102 Kit: RSL020M304 Kit: RSL020M506 Kit: RSL020H708 Kit: RSL020H910
Base RSLBA02 Base RSLBA04 Base RSLBA06 Base RSLBA08 Base RSLBA10
Top RSLTA01 Top RSLTA03 Top RSLTA05 Top RSLTA07 Top RSLTA09
Weight 317 lbs. Weight 327 lbs. Weight 302 lbs. Weight 399 lbs. Weight 477 lbs.
Fastest Mile Fastest Mile Fastest Mile Fastest Mile Fastest Mile
[3-sec Gust] E.P.A [3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust] E.P.A.
70 [85] 70 70 [85] 80 70 [85] 80 70 [85] 80 70 [85] 80
75 [90] 61 75 [90] 74 75 [90] 80 75 [90] 80 75 [90] 80
80 [100] 53 80 [100] 65 80 [100] 68 80 [100] 80 80 [100] 80
90 [110] 42 90 [110] 48 90 [110] 50 90 [110] 80 90 [110] 80
100 [120] 33 100 [120] 35 100 [120] 36 100 [120] 65 100 [120] 68
30’ Towers
18” 25” 28” 35” 42”
21” 28” 32” 38” 45”
25“ 32“ 35“ 42“ 49“
45”
28” 35” 38” 52”
Base RSLBA03 Base RSLBA05 Base RSLBA06 Base RSLBA08 Base RSLBA10
Top RSLTA01 Top RSLTA03 Top RSLTA04 Top RSLTA06 Top RSLTA08
Weight 440 lbs. Weight 445 lbs. Weight 450 lbs. Weight 551 lbs. Weight 687 lbs.
Fastest Mile E.P.A. Fastest Mile E.P.A. Fastest Mile E.P.A. Fastest Mile E.P.A. Fastest Mile E.P.A.
[3-sec Gust] [3-sec Gust] [3-sec Gust] [3-sec Gust] [3-sec Gust]
70 [85] 70 70 [85] 80 70 [85] 80 70 [85] 80 70 [85] 80

75 [90] 61 75 [90] 74 75 [90] 78 75 [90] 80 75 [90] 80
80 [100] 53 80 [100] 65 80 [100] 64 80 [100] 73 80 [100] 80
90 [110] 41 90 [110] 45 90 [110] 43 90 [110] 55 90 [110] 80
100 [120] 30 100 [120] 29 100 [120] 28 100 [120] 42 100 [120] 60
119
SS
40’ Towers
SELF-SUPPORTING TOWERS - RSL
18” 21” 28” 35” 38”
21” 25” 32” 38” 42”
25” 28” 35” 42” 45”
28” 32” 38” 45” 49”
32” 35” 42” 49” 52”
Base RSLBA04 Base RSLBA02
RSLBA05 Base RSLBA02
RSLBA10
Top RSLTA01 Top RSLTA01
RSLTA02 Top RSLTA01
RSLTA04 Top RSLTA01
RSLTA06 Top RSLTA01
RSLTA07
Weight 585 lbs. Weight 317
590 lbs. Weight 317
639 lbs. Weight 317
788 lbs.
lbs. Weight 317
876 lbs.
70 [85] 54 70 [85] 70
63 70 [85] 70
80 70 [85] 70
80 70 [85] 70
80
75 [90] 44 75 [90] 61
52 75 [90] 61
75 75 [90] 61
80 75 [90] 61
80
80 [100] 36 80 [100] 53
43 80 [100] 53
62 80 [100] 53
69 80 [100] 53
80
90 [110] 24 90 [110] 42
29 90 [110] 42
40 90 [110] 42
52 90 [110] 42
75
100 [120] 15 100 [120] 33
19 100 [120] 33
25 100 [120] 33
40 100 [120] 33
49
50’ Towers
18” 21” 25” 32” 35”
21” 25” 28” 35” 38”
25” 28” 32” 38” 42”
28” 32” 35” 42” 45”
32” 35” 38” 45” 49”
35” 38” 42” 49” 52”

RSLBA06 Base RSLBA07 Base RSLBA09 Base RSLBA02
RSLBA10
RSLTA02 Top RSLTA03 Top RSLTA05 Top RSLTA01
RSLTA06
Weight 735 lbs. Weight 317
742 lbs. Weight 786 lbs. Weight 938 lbs. Weight 317 lbs.
1028 lbs.
70 [85] 54 70 [85] 70
43 70 [85] 67 70 [85] 80 70 [85] 70
80
75 [90] 44 75 [90] 61
34 75 [90] 54 75 [90] 73 75 [90] 61
76
80 [100] 36 80 [100] 53
26 80 [100] 44 80 [100] 61 80 [100] 53
66
90 [110] 24 90 [110] 42
15 90 [110] 30 90 [110] 44 90 [110] 42
49
100 [120] 15 100 [120] 33
6 100 [120] 16 100 [120] 30 100 [120] 33
38
60’ Towers
18” 21” 25” 28” 32”
35”
21” 25” 28” 32”
38”
25” 28” 32” 35”
42”
28” 32” 35” 38”
45”
32” 35” 38” 42”
49”
35” 38” 42” 45”
52”
38” 42” 45” 49”
RSLBA02 Base RSLBA08 Base RSLBA09
RSLTA01 Top RSLTA03 Top RSLTA04
RSLTA01 Top RSLTA05
Weight 914 lbs. Weight 931 lbs.
317 Weight 1026 lbs. Weight 1086 lbs.
317 lbs. Weight 1217 lbs.
Fastest Mile Fastest Mile Fastest Mile Fastest Mile Fastest Mile
[3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust] E.P.A.
70 [85] 23 70 [85] 40
70 70 [85] 60 70 [85] 78
70 70 [85] 80
75 [90] 15 75 [90] 31
61 75 [90] 48 75 [90] 67
61 75 [90] 68
80 [100] 9 80 [100] 24
53 80 [100] 38 80 [100] 54
53 80 [100] 56
90 [110] 2 90 [110] 13
42 90 [110] 21 90 [110] 35
42 90 [110] 40
100 [120] - 100 [120] 5
33 100 [120] 11 100 [120] 21
33 100 [120] 27
121
SS
70’ Towers
SELF-SUPPORTING TOWERS - RSL
18” 21” 25” 28”
21” 25” 28” 32”
25” 28” 32” 35”
28” 32” 35” 38”
32” 35” 38” 42”
35” 38” 42” 45”
38” 42” 45” 49”
42” 45” 49” 52”
Kit: RSL070L107 Kit: RSL070M208 Kit: RSL070M309 Kit: RSL070H410

RSLBA08 Base RSLBA09 Base RSLBA10
RSLTA02 Top RSLTA03 Top RSLTA04
Weight 1096 lbs. Weight 914 lbs.
1141 lbs. Weight 1263 lbs. Weight 1361 lbs.
Fastest Mile E.P.A. Fastest Mile Fastest Mile Fastest Mile E.P.A.
[3-sec Gust] [3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust]
70 [85] 23 70 [85] 23
38 70 [85] 58 70 [85] 74
75 [90] 15 75 [90] 15
29 75 [90] 46 75 [90] 60
80 [100] 9 80 [100] 9
21 80 [100] 36 80 [100] 48
90 [110] - 90 [110] 82 90 [110] 21 90 [110] 26
100 [120] - 100 [120] - 100 [120] 11 100 [120] 13
90’ Towers
80’ Towers
18” 21” 25” 18” 21”
21” 25” 28” 21” 25”
25” 28” 32” 25” 28”
28” 32” 35” 28” 32”
32” 35” 38” 32” 35”
35” 38” 42” 35” 38”
38” 42” 45” 38” 42”
42” 45” 49” 42” 45”
45” 49” 52” 45” 49”

Kit: RSL080L108 Kit: RSL080M209 Kit: RSL080H310
Base RSLBA08 Base RSLBA09 Base RSLBA10 49” 52”
Top RSLTA01 Top RSLTA02 Top RSLTA03 Kit: RSL090H210
Kit: RSL090L109
Weight 1322 lbs. Weight 1422 lbs. Weight 1527 lbs. Base RSLBA09 Base RSLBA10
Fastest Mile Fastest Mile Fastest Mile
[3-sec Gust] E.P.A. [3-sec Gust] E.P.A. [3-sec Gust] E.P.A. Top RSLTA01 Top RSLTA02
70 [85] 21 70 [85] 36 70 [85] 52 Weight 1563 lbs. Weight 1642 lbs.
75 [90] 14 75 [90] 26 75 [90] 39 Fastest Mile
E.P.A. Fastest Mile E.P.A.
[3-sec Gust] [3-sec Gust]
80 [100] 7 80 [100] 19 80 [100] 26 70 [85] 19 70 [85] 33
90 [110] - 90 [110] 6 90 [110] 10 75 [90] 12 75 [90] 23
100 [120] - 100 [120] - 100 [120] - 80 [100] 5 80 [100] 13
90 [110] - 90 [110] -
100 [120] - 100 [120] -
123
OPTIONAL ACCESSORIES
100’ Towers
18”
RSLTM12 RSLTM34
21” Fits Towers: Fits Towers:
RSL020L102 RSL020M304
RSL030L103 RSL030M305
RSL040L104 RSL040M306
25” RSL050L105 RSL050M307
3’ - 1 1/2” RSL060L206 RSL060M308
RSL070L107 RSL070M309
RSL080L108 RSL070H410
RSL080M209 RSL080H310
28” RSL090L109
RSL090H210 RSLTM56
RSL100S110 Fits Towers:
RSL050H509
32” RSL060H510
Top Mount
35”
38” 3’
6’
5’
42”
45”
Side Arm - RSLSA Dish Mount - RSLDM
49” Step Bolt Kit
Ordering Information
TOWER PART
52” HEIGHT NUMBER
Anti-Climb Panel 20’ RSLSB20
Kit: RSL100S110 30’ RSLSB30
RSLAC10
Base RSLBA10 40’ RSLSB40
50’ RSLSB50
Top RSLTA01 60’ RSLSB60
Weight 1808 lbs. 70’ RSLSB70
80’ RSLST80
Fastest Mile E.P.A.
[3-sec Gust] 90’ RSLSB90
100’ RSLSB100
70 [85] 17
75 [90] 8
80 [100] -
Safety Cable Systems
90 [110] -
100 [120] - Tower Height Part Number
20’ - 50‘ RSL050TT
60’ - 100’ RSL100TT
Grounding Kit shown on page 126.
RSL
B A S E K I T I N F O R M AT I O N
Section
Tower Leg Tower Diagonal
Kit
Leg Splice
(Included in Tower
Section Kit)
Base Top Horizontal

L 2x2x3/16”
Tower Base Base Leg Weld’t

Kit
Tower Base Diagonal

L 2x2x3/16”
Base Bolt Assembly

Base Bottom 3/8”x1 1/2” GR. 5
Horizontal
L 2x2x3/16” Tower Base Kit Details
(Cast into foundation)
Tower Base Kit # Total (lbs.)
RSLBA02 (Section RSL2) 126
RSLBA03 (Section RSL3) 132.5
RSLBA04 (Section RSL4) 136
125
RSL
GROUNDING
Tower Angle Leg
Leg Splice
Step Bolt Leg
1/4”x1” Bolt (If Applicable)
Assembly Ground Lug
5/8”x2” A325 Connected to Foundation
Bolt Assembly Tower Leg
Tower Diagonal Splice #4 Tinned Solid #4 Tinned Solid A
Ground Lug Wire Copper Wire Copper Wire
To Plate (Tinned) 10’ LG 10’ LG
Top of Tower
Foundation Tower Base
Kit A
Grounding
19ø x 3050 LG Arrangement
(3/4” ø x 10’ LG) Plan
300mm (12”) Galv. Ground Rod
Nominal
Grounding Kit Details
(Optional Kit Ordered Separately)
Ground Rod
Clamp
View A - A
19ø x 3050 LG.
(3/4” ø x 10’ LG.)
Galv. Ground Rod
RSLGR Grounding Kit - Bill of Material

Description Qty.
Grounding Lug Galv. BAR .25x1.5” (A36) 2
3/4 DIA. Galv. GRD Rod (10’) 2
GRD Clamp Wire to Galv. Rod 2

GRD Wire #4 Solid Copper Tinned (10’) 2
GRD Clamp Wire to Plate (Tinned) 2
1/4”x1” Bolt Assembly 2
5/8”x2” Bolt Assembly (A325) 2
Lock Washer 5/8 (Spring) Galv. 2
RSL
F O U N D AT I O N I N F O R M AT I O N
Use Horizontal Brace for Leveling

3/4” Chamfer Typ. 4 Sides
P
Final Grade 6”
42”
48”
3” Min. Concrete Cover

Horizontal #7 bars equally
spaced @ 12” c/c each way
top & bottom.
(C) At top of pad
Center of Pad
and Tower
B
A
Stub Base Dimensions (in.) Max. Base Reactions

Concrete No. 7 Overturning Shear
Section No. A B C P (Cu. Yds) Bars Req. (KIP-FT) (KIPS)
RSLBA02 84 42 28 10-1/2 7.3 32 51 3.0
RSLBA03 90 45 29 12-1/2 8.3 32 57 3.0
RSLBA04 90 45 27 11-1/4 8.3 32 65 3.0
RSLBA05 96 48 28 11-1/2 9.5 36 71 3.0
RSLBA06 96 48 26 12 9.5 36 78 3.0
RSLBA07 108 54 30 13 12.0 40 114 4.0
RSLBA08 114 57 31 12-3/4 13.4 40 124 4.5
RSLBA09 120 60 32 13-1/2 14.8 44 171 5.0
RSLBA10 126 63 33 12-3/4 16.3 44 184 5.5
127
RSL
DESIGN GENERAL NOTES
1. Tower designs conform to ANSI/TIA/EIA-222-F for the basic wind speeds indicated without ice. Tower designs also
conform to the ANSI/TIA/EIA Standard for 1/2 inch radial ice load occuring simultaneously with 75% of the no ice design
wind pressures. The appropriate design criteria for a site must be verified prior to installation.
2. Antennas and mounts are assumed to be symmetrically mounted at or below the top of the tower for determining overall
reactions and member forces. Design assumes the weight of antennas and mounts do not exceed 300 lbs. Local stresses
due to mounting arrangements for site-specific applications have not been considered and must be investigated by
others on an individual site basis.
3. The allowable effective projected areas (EPA) indicated include the summation of the projected areas of antennas and
mounts multiplied by their appropriate drag factors. The allowable effective projected areas are based on applications
without the use of anti-climb panels. The use of anti-climb panels will reduce the allowable effective projected areas
indicated. When 1/2 inch of radial ice is to be considered for an application, the additional EPA of the ice of antennas
and mounts shall be included in the summation.
4. Design assumes maximum top mast load is limited to 5 sq. ft. EPA and 100 lbs. vertical load. All other loading is assumed
to be mounted below the top mast.
5. Tower designs assume a 1/2 inch transmission line for each 10 square feet of EPA up to a maximum of three lines, one
line per tower face.
6. Foundation designs are in accordance with ANSI/TIA/EIA-222-F, “Structural Standards for Steel Antenna Towers
and Antenna Supporting Structures”, section 7, for all “normal” soil conditions. “Normal” soil is defined as dry, cohesive
soil with an allowable net vertical bearing capacity of 4000 PSF and an allowable net horizontal pressure of 400 PSF
per linear foot of depth to a maximum of 4000 PSF.
NOTES
Phone (309) 697-4400 • Fax (309) 697-5612 • www.rohnnet.com • The Industry Standard 129
SELF-SUPPORTING
SSV
20’ 1W
20’ 2W All Welded

Construction
20’ 3WN GENERAL USE

10’
3WNB
The ROHN SSV tower has been in service for over
20’ 4N 30 years. The design utilizes standard parts ar-
ranged to create a unique structure. The legs
are tubular with angle braces at the bottom and
20’ 5N solid legs and braces in the top sections. This
tower is used in a variety of applications, from
PCS structures and Broadband to Security and
20’ 6N Sports Lighting and more. The SSV has proven to
be one of the industry’s most efﬁcient and pre-
ferred structures. All ROHN towers are hot-dip
20’ 7N galvanized, inside and out for corrosion protec-
tion.
Nominal
20’ 8N Section Spread Dimension
Number Upper Lower
1W 1’ - 2” 1’ - 2”
20’ 9N
2W 1’ - 2” 1’ - 6”
All Bolted 3WN 1’ - 6” 1’ - 10”

20’ 10N
Construction
4N 1’ - 10” 2’ - 2”
5N 2’ - 2” 2’ - 6”
20’ 11N
6N 2’ - 6” 4’ - 6 1/4”
7N 4’ - 6 1/4” 6’ - 6 3/4”
20’ 12N
8N 6’ - 6 3/4” 8’ - 6 3/4”
20’ 13N 9N 8’ - 6 3/4” 10’ - 6 3/4”
10N 10’ - 6 3/4” 12’ - 7 1/4”
11N 12’ - 7 1/4” 14’ - 7 7/8”

20’ 14N
12N 14’ - 7 7/8” 16’ - 8 3/8”
20’ 15N 13N 16’ - 8 3/8” 18’ - 8 3/8”
14N 18’ - 8 3/8” 20’ - 9 3/8”
20’ 16N 15N 20’ - 9 3/8” 22’ - 9 3/8”
16N 22’ - 9 3/8” 24’ - 9 3/8”

320’ Tower
SELF-SUPPORTING
40’ - 190’
70 MPH [NO ICE]
Tower Tower Allowable Projected Area Top Base Section Base Reactions
Height Assembly Tower Top 30’ Below Top Section Part A-Bolts Face Down load Uplift Shear OTM
(ft.) Number Rounds (Flats) Rounds (Flats) Number 12 Req. Spread (lbs.) (lbs.) (lbs.) (ft. lbs.)
40 SS040D70 16.7 (10) 20 (12) 2W 3WN SB3 1’ - 10 14,300 13,500 970 22,000
50 SS050D70 15 (9) 18.3 (11) 1WB 3WN SB3 1’ - 10 19,200 18,400 970 29,700
60 SS060D70 15 (9) 18.3 (11) 2W 4N SB4 2’ - 2 23,000 21,900 1,100 42,100
70 SS070D70 13.3 (8) 16.7 (10) 1WB 4N SB4 2’ - 2 27,300 26,100 1,130 50,000
80 SS080D70 13 (8) 16.7 (10) 2W 5N SB5 2’ - 6 31,600 30,100 1,320 66,500
90 SS090D70 11.7 (7) 15 (9) 1WB 5N SB5 2’ - 6 35,200 33,600 1,330 74,200
100 SS100D70 11.7 (7) 15 (9) 2W 6N62 5/8X42 4’ - 6 1/4 26,000 24,100 1,850 97,900
110 SS110D70 10 (6) 14.2 (8.5) 1WB 6N62 5/8X42 4’ - 6 1/4 28,200 26,200 1,870 106,300
120 SS120D70 10 (6) 14.2 (8.5) 2W 7N165 5/8X42 6’ - 6 3/4 26,300 24,000 2,510 141,700
130 SS130D70 9.2 (5.5) 13.3 (8) 1WB 7N165 5/8X42 6’ - 6 3/4 28,300 25,900 2,540 152,600
140 SS140D90 9.2 (5.5) 13.3 (8) 2W 8N106 5/8X42 8’ - 6 3/4 29,200 26,300 3,310 204,100
150 SS150D70 8.3 (5) 12.5 (7.5) 1WB 8N106 5/8X42 8’ - 6 3/4 30,800 27,800 3,340 215,300
160 SS160D70 8.3 (5) 12.5 (7.5) 2W 9N325 5/8X42 10’ - 6 3/4 33,300 29,900 4,230 286,400
170 SS170D70 7.5 (4.5) 12.5 (7.5) 1WB 9N325 5/8X42 10’ - 6 3/4 34,900 31,500 4,280 301,000
180 SS180D70 7.5 (4.5) 12.5 (7.5) 2W 10N387 3/4X48 12’ - 7 1/4 38,500 34,500 5,350 395,700
190 SS190D70 6.7 (4) 11.7 (7) 1WB 10N387 3/4X48 12’ - 7 1/4 39,700 35,600 5,380 407,700
General Notes:
1. Tower designs are in accordance with approved national standard ANSI/EIA-222-F-1996 (no ice).
2. Equivalent flat-plate antenna areas based on EIA RS-222-C, must not exceed the areas shown for flat member antennas.
3. Tower designs assume allowable projected areas are symmetrically placed on the tower.
4. Designs assume one 7/8 line to top and two 7/8 lines to 30 feet below top, one per face.
5. Do not install or dismantle tower within falling distance of electrical and/or telephone lines.
7. Install warning plate (P/N: ACWS) in a highly visible location.
8. All antenna installations must be grounded in accordance with local and national codes.
9. All towers are provided with a (P/N: ITT) tapered top.
131
SELF-SUPPORTING
S TA N D A R D S E C T I O N S
Bracing Detail for Sections 1W - 3WN Bracing Detail for Sections 4N & 5N Bracing Detail for Sections 6N & 11N
Solid Round Legs & Solid Round Braces Solid Round Legs & Solid Round Braces Tubular Legs & Angle Braces
STANDARD SECTIONS
Weights
Section No. Legs Braces Total
1W - - 107
2W - - 156
3WN - - 235
4N 260 175 457
5N 345 195 576
6N 290 190 515
7N 300 245 579
8N 426 274 713 Bracing Detail for Sections 12N & 16N
9N 420 300 760 Tubular Legs & Angle Braces
10N 430 400 868
11N 570 840 1,459
12N 690 825 1,612 TYPICAL SHORT BASE
13N 790 910 1,796
14N 845 1,625 2,516
15N 1,155 2,000 3,165
16N 1,155 2,150 3,305
* All weights are approximate. Total section
weight depends on final design.
Part No: SB2, SB3, SB4 & SB5
SELF-SUPPORTING
S TA N D A R D F O U N D AT I O N S
Round or Square
Tower Axis
and center Y
of pad Vertical Bars
Tower Axis
YY
Section A-A
Plan View W
(square)
C Plan View 6” G.L.

6” G.L.
Vert. Bars
Vert. Bars equally
equally spaced
#4 Circular spaced,
Ties 180 o hooks
at bottom 6” D
D G.L.
A A
Hor. Bars 4’0 #4 Circular
12” O.C. Ties
each way
2’0 #7 Bars 12”
O.C. each way
A
(square)
Mat Drilled Pier
Pier & Pad Elevation View Elevation View
Elevation View
Anchor Bolt Data Pier & Pad Mat Drilled Pier

Tower Allow. Allow.
Base Leg Shear LayoutDimensions Size12 Bolt Proj. Dimensions Req’dConc.
Sec.t Load (lbs.per Req’d Circle (in.) Vert. Hor. (cu.yds. W Req’ d
Conc. D
Vert.
Y Bars
Req’d
Conc.
No. (lbs.) leg) or Short Dia. D A C Bars Bars 3fdns) (cu.yds.) (cu.yds.)
M N R Base (in.) Round Square
1W 4,530 - 1’2 1’0 1/8 0’8 1/16 - 2 21/32 - - - - - - - - 4’0 2.4 - - - -
2W 11,200 - 1’6 1‘ 3 9/16 0‘ 10 3/8 SB2 2 21/32 - - - - - - - - 5’6 4.5 - - - -
3WN 19,600 - 1’10 1’7 1/16 1’0 11/16 SB3 3 1/2 - - - - - - - - 6’9 6.8 - - - -
4N 28,000 - 2’2 1‘ 10 1/2 1‘ 3 SB4 4 1/4 - - - - - - - - 8’0 9.5 - - - -
5N 36,000 - 2’6 2’2 1’5 5/16 SB5 4 1/4 - - - - - - - - 8’9 11.3 - - - -
6N 33,730 - 4’6 1/4 3‘ 11 2‘ 7 15/16 5/8X42 4 15/16 3 1/2 - - - - - - - 10’3 15.6 - - - -
7N 33,730 4,000 6’6 3/4 5’8 3/16 3’9 1/2 5/8X42 4 15/16 3 1/2 8‘ 0 4’6 2‘ 0 (8) #6 #6 6.3 6.9 11’6 19.6 - - - -
8N 52,530 6,000 8’6 3/4 7‘ 5 4‘ 11 5/16 5/8X42 4 15/16 3 1/2 8’9 5‘ 6 2’0 (8) #7 #6 8.7 9.4 14’3 30.1 18’6 2’6 (10) #6 10.4
9N 43,600 7,500 10’6 3/4 9’1 3/4 6’1 3/16 5/8X42 4 15/16 3 1/2 8‘ 9 5’6 2‘ 0 (8) #7 #6 8.7 9.4 16’0 37.9 16’0 2‘ 6 (10) #6 9.0
10N 43,600 10,000 12’7 1/4 10‘ 11 7‘ 3 5/16 3/4X48 5 21/32 4 8’9 5‘ 6 2’0 (8) #7 #6 8.7 9.4 18’3 49.3 16’0 2’6 (10) #6 9.0
11N 64,930 10,000 14’7 7/8 12’8 15/16 8’5 9/16 7/8X60 7 1/16 5 10‘ 0 5’6 2‘ 6 (8) #8 #6 10.8 12.0 - - 21’9 2‘ 6 (10) #6 12.2
12N 63,600 10,000 16’8 3/8 16‘ 2 5/16 9‘ 7 11/16 7/8X60 7 1/16 5 10’0 5‘ 6 2’6 (8) #8 #6 10.8 12.0 - - 21’6 2’6 (10) #6 12.0
13N 82,930 10,000 18’8 3/817’11 15/16 10’9 9/16 7/8X60 7 1/16 5 11‘ 0 5’6 2‘ 6 (10) #8 #6 11.3 12.7 - - 22’0 3‘ 0 (12) #6 17.7
14N 82,930 10,000 20’9 3/8 19‘ 8 3/4 12‘ 0 1X70 9 1/2 5 1/2 11’0 5‘ 6 2’6 (10) #8 #6 11.3 12.7 - - 22’0 3’0 (12) #6 17.7
15N 123,330 15,000 22’9 3/8 22’9 3/8 13’1 13/16 1X70 9 1/2 5 1/2 12‘ 6 6‘6 3‘ 0 (12) #8 #6 17.3 19.7 - - 27’6 3‘ 6 (12) #7 30.0
16N 129,330 15,000 24’9 3/8 21’5 9/16 14’3 11/16 1X70 9 1/2 5 1/2 12’6 6’6 3’0 (12) #8 #6 17.3 19.7 - - 27’6 3’6 (12) #7 30.0
133
SELF-SUPPORTING
SSV
20’ 1W
20’ 2W All Welded

Construction
HEAVY DUTY
20’ 3WN
10’
3WNB GENERAL USE
20’ 4N The ROHN SSV HD has the same features and util-
ity as the SSV tower, but with Heavy Duty legs and
braces. The heavy duty allows for the structure
20’ 5N to support more loading and higher wind and
ice loading. This tower serves the same applica-
tions as the SSV including PCS, Broadband, Se-
20’ 6N curity, Sports Lighting and many others. The SSV
HD, also has standard “pre-engineered” towers
created from standard sections. All ROHN tow-
20’ 7N
ers are hot-dip galvanized, inside and out for
corrosion protection.
20’ 8N Nominal
Section Spread Dimension
Number Upper Lower
20’ 9NH 1W 1’ - 2” 1’ - 2”
2W 1’ - 2” 1’ - 6”
20’ 10NH All Bolted
Construction 3WN 1’ - 6” 1’ - 10”
4N 1’ - 10” 2’ - 2”
20’ 11N 5N 2’ - 2” 2’ - 6”
6N 2’ - 6” 4’ - 6 1/4”
20’ 12NH 7N 4’ - 6 1/4” 6’ - 6 3/4”
8N 6’ - 6 3/4” 8’ - 6 3/4”
20’ 13NH
9NH 8’ - 6 3/4” 10’ - 6 3/4”
10NH 10’ - 6 3/4” 12’ - 7 1/4”

20’ 14NH 11N 12’ - 7 1/4” 14’ - 7 7/8”
12NH 14’ - 7 7/8” 16’ - 8 3/8”

20’ 15NH
13NH 16’ - 8 3/8” 18’ - 8 3/8”
14NH 18’ - 8 3/8” 20’ - 9 3/8”

20’ 16NH
15NH 20’ - 9 3/8” 22’ - 9 3/8”
16NH 22’ - 9 3/8” 24’ - 9 3/8”

320’ Tower
SELF-SUPPORTING
40’ - 190’
90 MPH [NO ICE]
Tower Tower Allowable Projected Area Top Base Section Base Reactions
Height Assembly Tower Top 30’ Below Top Section Part A-Bolts Face Down load Uplift Shear OTM
(ft.) Number Rounds (Flats) Rounds (Flats) Number 12 Req. Spread (lbs.) (lbs.) (lbs.) (ft. lbs.)
40 SS040D90 16.7 (10) 20 (12) 3WN 4N SB4 2’ - 2 20,800 19,800 1,700 38,100
50 SS050D90 16.7 (10) 20 (12) 3WNB 5N SB5 2‘ - 6 27,900 26,600 1,950 58,900
60 SS060D90 14.2 (8.5) 17.5 (10.5) 3WN 5N SB6 2’ - 6 33,700 32,400 1,930 71,400
70 SS070D90 14.2 (8.5) 17.5 (10.5) 3WNB 6N 5/8X42AB 4’ - 6 1/4 27,100 25,500 2,760 103,100
80 SS080D90 12.5 (7.5) 15.8 (9.5) 3WN 6N 5/8X42AB 4’ - 6 1/4 31,300 29,600 2,820 119,300
90 SS090D90 12.5 (7.5) 15.8 (9.5) 3WNB 7N 5/8X42AB 6’ - 6 3/4 31,100 29,100 3,850 169,900
100 SS100D90 10 (6) 13.3 (8) 3WN 7N 5/8X42AB 6’ - 6 3/4 33,100 30,900 3,830 180,600
110 SS110D90 10 (6) 13.3 (8) 3WNB 8N 5/8X42AB 8’ - 6 3/4 36,000 33,400 5,070 255,500
120 SS120D90 8.3 (5) 11.7 (7) 3WN 8N 5/8X42AB 8’ - 6 3/4 38,100 35,400 5,100 270,300
130 SS130D90 8.3 (5) 11.7 (7) 3WNB 9NH 5/8X42AB 10’ - 6 3/4 42,900 39,700 6,520 375,800
140 SS140D90 6.7 (4) 10 (6) 3WN 9NH 5/8X42AB 10’ - 6 3/4 44,500 41,200 6,540 389,800
150 SS150D90 6.7 (4) 10 (6) 3WNB 10NH 5/8X42AB 12’ - 7 1/4 50,900 47,000 8,280 532,100
160 SS160D90 5.8 (3.5) 8.3 (5) 3WN 10NH 3/4X48AB 12’ - 7 1/4 52,700 48,700 8,330 550,900
170 SS170D90 5.8 (3.5) 8.3 (5) 3WNB 11N 3/4X48AB 14’ - 7 7/8 60,900 56,000 10,570 739,500
180 SS180D90 5 (3) 7.5 (4.5) 3WN 11N 7/8X60AB 14’ - 7 7/8 62,900 57,900 10,650 763,700
190 SS190D90 5 (3) 7.5 (4.5) 3WNB 12NH 7/8X60AB 16’ - 8 3/8 73,000 66,900 13,060 1,007,000
General Notes:
1. Tower designs are in accordance with approved national standard ANSI/EIA-222-F-1996 (no ice).
2. Equivalent flat-plate antenna areas based on EIA RS-222-C, must not exceed the areas shown for flat member antennas.
3. Tower designs assume allowable projected areas are symmetrically placed on the tower.
4. Designs assume one 7/8 line to top and two 7/8 lines to 30 feet below top, one per face.
5. Do not install or dismantle tower within falling distance of electrical and/or telephone lines.
7. Install warning plate (P/N: ACWS) in a highly visible location.
8. All antenna installations must be grounded in accordance with local and national codes.
9. All towers with 3WN top section are provided with a (P/N: 3TT) tapered top.
10. All towers with 3WNB top section provided with a (P/N: 4TTN) tapered top.
135
SELF-SUPPORTING
H E AV Y D U T Y S E C T I O N S
Bracing Detail for Sections 1W - 3WN Bracing Detail for Sections 4N & 5N Bracing Detail for Sections 6N & 11N
Solid Round Legs & Solid Round Braces Solid Round Legs & Solid Round Braces Tubular Legs & Angle Braces
HEAVY DUTY SECTIONS

Weights
Section No. Legs Braces Total
1W - - 116
2W - - 160
3WN - - 230
4N 260 175 435
5N 345 195 540
6N 290 190 480
7N 300 245 545
8N 426 274 700 Bracing Detail for Sections 12N & 16N
9NH 535 305 840 Tubular Legs & Angle Braces
10NH 545 400 945
11N 570 840 1,410
12NH 905 825 1,730 TYPICAL SHORT BASE
13NH 1,050 910 1,960
14NH 1,110 1,625 2,735
15NH 1,530 2,000 3,530
16NH 1,530 2,150 3,680
* All weights are approximate. Total section
weight depends on final design.
SELF-SUPPORTING
H E AV Y D U T Y F O U N D AT I O N S
Round or Square
Tower Axis
and center
of pad Vertical Bars
Tower Axis
YY
Section A-A
Plan View W
(square)
C Plan View 6” G.L.

6” G.L.
Vert. Bars
Vert. Bars equally
equally spaced
#4 Circular spaced,
Ties 180 o hooks
at bottom 6” D
D G.L.
A A
Hor. Bars 4’0 #4 Circular
12” O.C. Ties
each way
2’0 #7 Bars 12”
O.C. each way
A
(square)
Mat Drilled Pier
Pier & Pad Elevation View Elevation View
Elevation View
Anchor Bolt Data Pier & Pad Mat Drilled Pier

Tower Allow. Allow.
Base Leg Shear LayoutDimensions Size12 Bolt Proj. Dimensions Req’dConc.
Sec.t Load (lbs.per Req’d Circle (in.) Vert. Hor. (cu.yds. W Req’ d
Conc. D
Vert.
Y Bars
Req’d
Conc.
No. (lbs.) leg) or Short Dia. D A C Bars Bars 3fdns) (cu.yds.) (cu.yds.)
M N R Base (in.) Round Square
1W 4,530 - 1’2 1’0 1/8 0’8 1/16 - 2 21/32 - - - - - - - - 4’0 2.4 - - - -
2W 11,200 - 1’6 1‘ 3 9/16 0‘ 10 3/8 SB2 2 21/32 - - - - - - - - 5’6 4.5 - - - -
3WN 19,600 - 1’10 1’7 1/16 1’0 11/16 SB3 3 1/2 - - - - - - - - 6’9 6.8 - - - -
4N 28,000 - 2’2 1‘ 10 1/2 1‘ 3 SB4 4 1/4 - - - - - - - - 8’0 9.5 - - - -
5N 36,000 - 2’6 2’2 1’5 5/16 SB5 4 1/4 - - - - - - - - 8’9 11.3 - - - -
6N 33,730 - 4’6 1/4 3‘ 11 2‘ 7 15/16 5/8X42 4 15/16 3 1/2 - - - - - - - 10’3 15.6 - - - -
7N 33,730 4,000 6’6 3/4 5’8 3/16 3’9 1/2 5/8X42 4 15/16 3 1/2 8‘ 0 4’6 2‘ 0 (8) #6 #6 6.3 6.9 11’6 19.6 - - - -
8N 52,530 6,000 8’6 3/4 7‘ 5 4‘ 11 5/16 5/8X42 4 15/16 3 1/2 8’9 5‘ 6 2’0 (8) #7 #6 8.7 9.4 14’3 30.1 18’6 2’6 (10) #6 10.4
9NH 54,000 6,500 10’6 3/4 9’1 3/4 6’1 3/16 5/8X42 4 15/16 3 1/2 9‘ 0 5’6 2‘ 0 (8) #7 #6 8.8 9.5 16’0 37.9 19’6 2‘ 6 (10) #6 10.9
10NH 56,000 8,000 12’7 1/4 10‘ 11 7‘ 3 5/16 3/4X48 5 21/32 4 9’0 5‘ 6 2’0 (8) #7 #6 8.8 9.5 18’3 49.3 19‘ 6 2’6 (10) #6 10.9
11N 64,930 10,000 14’7 7/8 12’8 15/16 8’5 9/16 7/8X60 7 1/16 5 10‘ 0 5’6 2‘ 6 (8) #8 #6 10.8 12.0 - - 21’9 2‘ 6 (10) #6 12.2
12NH 85,600 10,000 16’8 3/8 16‘ 2 5/16 9‘ 7 11/16 7/8X60 7 1/16 5 11’0 5‘ 6 2’6 (10) #8 #6 11.3 12.7 - - 22’9 3’0 (12) #6 18.3
13NH 114,100 12,500 18’8 3/817’11 15/16 10’9 9/16 7/8X60 7 1/16 5 12‘ 0 6’3 3‘ 0 (12) #8 #6 16.3 18.5 - - 25‘ 0 3‘ 6 (12) #7 27.3
14NH 114,100 15,000 20’9 3/8 19‘ 8 3/4 12‘ 0 1X70 9 1/2 5 1/2 12’0 6’3 3’0 (12) #8 #6 16.3 18.5 - - 25’0 3’6 (12) #7 27.3
15NH 152,000 15,000 22’9 3/8 22’9 3/8 13’1 13/16 1X70 9 1/2 5 1/2 13‘ 0 7‘ 3 3‘ 0 (12) #8 #6 19.9 22.4 - - 30‘ 0 4‘ 0 (12) #8 42.6
16NH 152,000 15,000 24’9 3/8 21’5 9/16 14’3 11/16 1X70 9 1/2 5 1/2 13’0 7’ 3 3’0 (12) #8 #6 19.9 22.4 - - 30’0 4’0 (12) #8 42.6
137
SS SELF-SUPPORTING TOWERS - SSMW
SELF-SUPPORTING
20’ B
20’ C
SSMW
20’ D GENERAL USE
20’ E The ROHN SSMW is a unique design using a K-

Brace system to allow free standing towers to
reach heights to 900’. The SSMW is designed with
20’ F
pipe legs and pipe braces with ﬂanges at each
end for connection. The MW design can be
20’ G used in conjunction with the SSV tower. All ROHN
towers are hot-dip galvanized, inside and out for
20’ H corrosion protection.
20’ J
Nominal
20’ K Number Upper Lower
B 8’ - 6 1/2” 8’ - 6 1/2”
20’ L
C 8’ - 6 1/2” 10’ - 7”
20’ M D 10’ - 7” 12’ - 7 1/2”
E 12’ - 7 1/2” 14‘ - 11 1/2“

30’ N F 14‘ - 11 1/2“ 17’ - 5 1/2”
G 17’ - 5 1/2” 19‘ - 11 1/2”
H 19‘ - 11 1/2” 22’ - 6 1/2“

30’ P
J 22’ - 6 1/2“ 25‘ - 0 1/2”
K 25‘ - 0 1/2” 27’ - 6 1/2“

30’ Q
L 27’ - 6 1/2“ 30‘ - 0 1/2”
M 30‘ - 0 1/2” 32’ - 6 1/2“

30’ R N 32’ - 6 1/2“ 36‘ - 3 1/2”
P 36‘ - 3 1/2” 40’ - 2 1/8“
30’ S Q 40’ - 2 1/8“ 43‘ - 11 1/8”
R 43‘ - 11 1/8” 47’ - 8 1/8“
S 47’ - 8 1/8“ 51’ - 5 1/8”

30’ T
T 51’ - 5 1/8” 55’ - 2 1/8”
400’ Tower
SELF-SUPPORTING TOWERS - SSMW SS
SELF-SUPPORTING
SSMW SECTIONS
Angle sub-horizontal Typical section assembly

bracing are used on detail for sections K, L & M.
sections B - J only.
Typical section assembly detail for sections B, C & D.
Section E, F, G & H are identical except
for the number of bays of bracing.
SSMW SECTIONS
SSMW tower section weights will vary.
Sections are designed for many different
sizes of braces and legs.
Bracing splice
Secondary horizontal connection are
sub-bracing are used on used on sections
sections Q, R, S & T only. Typical section assembly
detail for sections N, P, Q, Q - T only.
R, S & T.
139
SS SELF-SUPPORTING TOWERS - SSVSR
SELF-SUPPORTING
SSVSR
20’ 1W
20’ 2W All Welded

Construction
20’ 3WN
10’
3WNB GENERAL USE
20’ 4N The ROHN SSVSR is similar in design to the ROHN

SSV but uses solid round legs instead of tubular
legs. The SSVSR gives the versatility to switch to a
20’ 5N solid leg if desired. The standard side arms, dish
mounts, ladders and waveguide support that
are used on the SSV can be used on the SSVSR.
20’ 6SR All ROHN towers are hot-dip galvanized, corro-
sion protection.
20’ 7SR
Nominal
20’ 8SR Section Spread Dimension
Number Upper Lower
1W 1’ - 2” 1’ - 2”
20’ 9SR
2W 1’ - 2” 1’ - 6”
All Bolted 3WN 1’ - 6” 1’ - 10”

20’ 10SR
Construction
4N 1’ - 10” 2’ - 2”
5N 2’ - 2” 2’ - 6”
20’ 11SR
6SR 2’ - 6” 4’ - 6 1/4”
7SR 4’ - 6 1/4” 6’ - 6 3/4”

20’ 12SR
8SR 6’ - 6 3/4” 8’ - 6 3/4”
20’ 13SR 9SR 8’ - 6 3/4” 10’ - 6 3/4”
10SR 10’ - 6 3/4” 12’ - 7 1/4”
11SR 12’ - 7 1/4” 14’ - 7 7/8”

20’ 14SR
12SR 14’ - 7 7/8” 16’ - 8 3/8”
20’ 15SR 13SR 16’ - 8 3/8” 18’ - 8 3/8”
14SR 18’ - 8 3/8” 20’ - 9 3/8”
20’ 16SR 15SR 20’ - 9 3/8” 22’ - 9 3/8”
16SR 22’ - 9 3/8” 24’ - 9 3/8”

320’ Tower
SELF-SUPPORTING TOWERS - SSVSR SS
SELF-SUPPORTING
SOLID ROD SECTIONS
Bracing Detail for Sections 1W - 3WN Bracing Detail for Sections 4N & 5N Bracing Detail for Sections 6SR & 11SR
Solid Round Legs & Solid Round Braces Solid Round Legs & Solid Round Braces Solid Legs & Angle Braces
SSVSR SECTIONS
SSVSR tower section weights will vary.
Bracing Detail for Sections 12SR & 16SR

Solid Legs & Angle Braces
TYPICAL SHORT BASE
141
SS SELF-SUPPORTING TOWERS - RS
SELF-SUPPORTING
10’ RSS06
20’ RSS06
RS
20’ RSS06
GENERAL USE
The ROHN RS is a unique solid leg tower that uses

20’ RSS06
an X-brace pattern angle braces. The RS tow-
ers can be strengthened by changing or adding
braces to sections. All ROHN towers are hot-dip
20’ RST08 galvanized for corrosion protection.
20’ RST10
20’ RST12
Nominal
Number Upper Lower
30’ RST15 RSS06 6’ 6’
RST08 6‘ 8‘
RST10 8’ 10’
RST12 10‘ 12‘

30’ RST18
RST15 12’ 15’
RST18 15‘ 18‘
RST21 18’ 21’
RST24 21‘ 24‘

30’ RST21
20’ RST24
10’
250’ Tower
SELF-SUPPORTING TOWERS - RS SS
SELF-SUPPORTING
RS SECTIONS
RSS Section RST Section

Solid Round Legs & Angle Braces Solid Round Legs & Angle Braces
RS SECTIONS
RS tower section weights will vary.
RST15 and Larger Sections

Solid Round Legs & Angle Braces
143
SS SELF-SUPPORTING TOWERS - REWORK
SELF-SUPPORTING REINFORCEMENTS
S TA N D A R D PA R T S AVA I L A B L E F O R T O W E R M O D I F I C AT I O N S
AND FIELD REINFORCEMENT
Horizontal Girt
(Typ)
Girt Support
Bracket
Tower Leg
(Ref ) Bolt
Assembly
Diagonal Tower For SS towers
Braces
1/2” Leg
U-bolt Center Plate
Girt Support Bracket

Bolt
Assemblies
Center Plate
Diagonal Tower
Braces (Ref ) Horizontal Girt (Typ)
1/2” Leg
Bolt VIEW A-A
SELF-SUPPORTING TOWERS - REWORK SS
SSMW SELF-SUPPORTING REINFORCEMENTS
S TA N D A R D PA R T S AVA I L A B L E F O R T O W E R M O D I F I C AT I O N S
AND FIELD REINFORCEMENT
U-bolt Connection
(Typical)
Bolt-on lugs are available for all

SSMW legs and internal braces.
INTERNAL TOWER VIEW
Added braces are shown as a dashed line.
145

Upload 1567785988 ROHN SSV

Uploaded by

Copyright:

Available Formats

Upload 1567785988 ROHN SSV

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Upload 1567785988 ROHN SSV

Uploaded by

Copyright:

Available Formats

SS SELF-SUPPORTING TOWERS

The self-supporting G-Series towers offer an easy,

• Completely hot-dip galvanized after fabrica-

Typical Self-Supporting Typical Self-Supporting

70 MPH - 1/2” Radial Ice

1/2” RADIAL ICE

80 MPH - 1/2” Radial Ice

90 MPH - 1/2” Radial Ice

1. Tower designs are in accordance with approved national standard ANSI/EIA-222-F.

Tower Axis &

Overturning Max. Allow Concrete

55G 22,900 1,600 6’ - 0” 5.3

Compacted Sand & Gravel

Tower Over-turning Concrete Req’d

20’ 12,100 4‘-9” 3.4

30’ 21,400 5’9” 4.9

40’ 32,600 6‘-6” 6.3

Maximum Load at Top

65SS010CT 65SS020CT 65SS030CT 65SS040CT 65SS050CT

4’-6” 4’-9” 5’-9” 6’-6” 7’-3”

SAFETY CABLE SYSTEM

*Top Mount RSL

The ROHN RSL is a light weight self-supporting tower

designed for use in broadband, public safety

and buildings. If your site is remote or rugged, the

RSL is shipped knocked down to reduce shipping,

cost and time.

•Available in heights from 20’ - 100’

• High strength angle legs

• Easy to transport and assemble

• Tower material is hot-dip galvanizied

42” - Safety device

21” 28” 35” 42” 49”

25” 32” 38” 45” 52”

21” 28” 32” 38” 45”

25“ 32“ 35“ 42“ 49“

70 [85] 70 70 [85] 80 70 [85] 80 70 [85] 80 70 [85] 80

18” 21” 28” 35” 38”

21” 25” 32” 38” 42”

25” 28” 35” 42” 45”

28” 32” 38” 45” 49”

32” 35” 42” 49” 52”

18” 21” 25” 32” 35”

21” 25” 28” 35” 38”

25” 28” 32” 38” 42”

28” 32” 35” 42” 45”

32” 35” 38” 45” 49”

35” 38” 42” 49” 52”

18” 21” 25” 28”

21” 25” 28” 32”

25” 28” 32” 35”

28” 32” 35” 38”

32” 35” 38” 42”

35” 38” 42” 45”

38” 42” 45” 49”

42” 45” 49” 52”

Kit: RSL070L107 Kit: RSL070M208 Kit: RSL070M309 Kit: RSL070H410

21” 25” 28” 21” 25”

25” 28” 32” 25” 28”