SRWE Module 15new

Module 15: IP Static Routing
Yogeswaran
Switching, Routing, and Wireless Essentials v7.0

(SRWE)
Module Objectives
Module Title: IP Static Routing
Module Objective: Configure IPv4 and IPv6 static routes.

Topic Title Topic Objective
Static Routes Describe the command syntax for static routes.
Configure IP Static Routes Configure IPv4 and IPv6 static routes.

Configure IP Default Static
Configure IPv4 and IPv6 default static routes.
Routes
Configure Floating Static
Configure a floating static route to provide a backup connection.
Routes
Configure IPv4 and IPv6 static host routes that direct traffic to a
Configure Static Host Routes
specific host.
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 2
15.1 Static Routes
Static Routes
Types of Static Routes
Static routes are commonly implemented on a network. This is true even when there is a
dynamic routing protocol configured.
Static routes can be configured for IPv4 and IPv6. Both protocols support the following
types of static routes:
• Standard static route
• Default static route
• Floating static route
• Summary static route
Static routes are configured using the ip route and ipv6 route global configuration
commands.
Static Routes
Next-Hop Options
When configuring a static route, the next hop can be identified by an IP address, exit
interface, or both. How the destination is specified creates one of the three following types
of static route:
• Next-hop route - Only the next-hop IP address is specified
• Directly connected static route - Only the router exit interface is specified
• Fully specified static route - The next-hop IP address and exit interface are
specified
Static Routes
IPv4 Static Route Command
IPv4 static routes are configured using the following global configuration command:
Router(config)# ip route network-address subnet-mask { ip-address

| exit-intf [ip-address]} [distance]
Note: Either the ip-address, exit-intf, or the ip-address and exit-intf parameters must be
configured.
Static Routes
IPv6 Static Route Command
IPv6 static routes are configured using the following global configuration command:
Router(config)# ipv6 route ipv6-prefix/prefix-length {ipv6-address

| exit-intf [ipv6-address]} [distance]
Most of parameters are identical to the IPv4 version of the command.
Static Routes
Dual-Stack Topology
The figure shows a dual-stack network topology. Currently, no static routes are configured
for either IPv4 or IPv6.
Static Routes
IPv4 Starting Routing Tables
• Each router has entries only for directly connected networks and associated local
addresses.
• R1 can ping R2, but cannot ping the R3 LAN
R1# show ip route | begin Gateway

Gateway of last resort is not set
172.16.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 172.16.2.0/24 is directly connected, Serial0/1/0
L 172.16.2.1/32 is directly connected, Serial0/1/0
C 172.16.3.0/24 is directly connected, GigabitEthernet0/0/0
L 172.16.3.1/32 is directly connected, GigabitEthernet0/0/0
R1#
R1# ping 172.16.2.2
Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.16.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5)
R1# ping 192.168.2.1
Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
.....
Static Routes
IPv6 Starting Routing Tables
• Each router has entries only for directly connected networks and associated local addresses.
• R1 can ping R2, but cannot ping the R3 LAN.
R1# show ipv6 route | begin C
C 2001:DB8:ACAD:2::/64 [0/0]
via Serial0/1/0, directly connected
L 2001:DB8:ACAD:2::1/128 [0/0]
via Serial0/1/0, receive
C 2001:DB8:ACAD:3::/64 [0/0]
via GigabitEthernet0/0/0, directly connected
L 2001:DB8:ACAD:3::1/128 [0/0]
via GigabitEthernet0/0/0, receive
L FF00::/8 [0/0]
via Null0, receive
R1#
R1# ping 2001:db8:acad:2::2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:DB8:ACAD:2::2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/3 ms)
R1# ping 2001:DB8:cafe:2::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:DB8:CAFE:2::1, timeout is 2 seconds:
% No valid route for destination
15.2 Configure IP Static
Routes
Configure IP Static Routes
IPv4 Next-Hop Static Route
In a next-hop static route, only the next-hop IP address is specified. The exit interface is
derived from the next hop. For example, three next-hop IPv4 static routes are configured
on R1 using the IP address of the next hop, R2.
R1(config)# ip route 172.16.1.0 255.255.255.0 172.16.2.2
R1(config)# ip route 192.168.1.0 255.255.255.0 172.16.2.2
R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.2.2
The resulting routing table entries on R1:
IPv6 Next-Hop Static Route
The commands to configure R1 with the IPv6 static routes to the
three remote networks are as follows:
R1(config)# ipv6 unicast-routing
R1(config)# ipv6 route 2001:db8:acad:1::/64

2001:db8:acad:2::2
R1(config)# ipv6 route 2001:db8:cafe:1::/64

2001:db8:acad:2::2

2001:db8:acad:2::2
The routing table for R1 now has routes to the three remote IPv6
networks.
IPv4 Directly Connected Static Route
When configuring a static route, another option is to use the exit interface to specify the
next-hop address. Three directly connected IPv4 static routes are configured on R1 using
the exit interface.
Note: Using a next-hop address is generally recommended. Directly connected static routes should
only be used with point-to-point serial interfaces.
R1(config)# ip route 172.16.1.0 255.255.255.0 s0/1/0
IPv6 Directly Connected Static Route
In the example, three directly connected IPv6 static routes
are configured on R1 using the exit interface.
Note: Using a next-hop address is generally
recommended. Directly connected static routes should
only be used with point-to-point serial interfaces.
R1(config)# ipv6 route 2001:db8:acad:1::/64

s0/1/0

s0/1/0

s0/1/0
IPv4 Fully Specified Static Route
• In a fully specified static route, both
the exit interface and the next-hop IP
address are specified. This form of
static route is used when the exit
interface is a multi-access interface
and it is necessary to explicitly identify
the next hop. The next hop must be
directly connected to the specified exit
interface. Using an exit interface is
optional, however it is necessary to
use a next-hop address.
• It is recommended that when the exit
interface is an Ethernet network, that
the static route includes a next-hop
address. You can also use a fully
specified static route that includes
both the exit interface and the next-
hop address.
IPv6 Fully Specified Static Route
In a fully specified static route, both the exit interface and the next-hop IPV6 address are specified.
There is a situation in IPv6 when a fully specified static route must be used. If the IPv6 static route
uses an IPv6 link-local address as the next-hop address, use a fully specified static route. The
figure shows an example of a fully specified IPv6 static route using an IPv6 link-local address as the
next-hop address.
IPv6 Fully Specified Static Route (Cont.)
The reason a fully specified static route must be used is because IPv6 link-local
addresses are not contained in the IPv6 routing table. Link-local addresses are only
unique on a given link or network. The next-hop link-local address may be a valid address
on multiple networks connected to the router. Therefore, it is necessary that the exit
interface be included.
The following example shows the IPv6 routing table entry for this route. Notice that both
the next-hop link-local address and the exit interface are included.
Verify a Static Route
Along with show ip route, show ipv6 route, ping and traceroute, other useful
commands to verify static routes include the following:
• show ip route static
• show ip route network
• show running-config | section ip route
Replace ip with ipv6 for the IPv6 versions of the command.
15.3 Configure IP Default
Static Routes
Configure IP Default Static Routes
Default Static Route
• A default route is a static route that
matches all packets. A single default route
represents any network that is not in the
routing table.
• Routers commonly use default routes that
are either configured locally or learned
from another router. The default route is
used as the Gateway of Last Resort.
• Default static routes are commonly used
when connecting an edge router to a
service provider network, or a stub router
(a router with only one upstream neighbor
router).
• The figure shows a typical default static
route scenario.
Default Static Route (Cont.)
IPv4 Default Static Route: The command syntax for an IPv4 default static route is similar to any
other IPv4 static route, except that the network address is 0.0.0.0 and the subnet mask is 0.0.0.0.
The 0.0.0.0 0.0.0.0 in the route will match any network address.
Note: An IPv4 default static route is commonly referred to as a quad-zero route.
The basic command syntax for an IPv4 default static route is as follows:
Router(config)# ip route 0.0.0.0 0.0.0.0 {ip-address | exit-intf}
IPv6 Default Static Route: The command syntax for an IPv6 default static route is similar to any
other IPv6 static route, except that the ipv6-prefix/prefix-length is ::/0, which matches all routes.
The basic command syntax for an IPv6 default static route is as follows:
Router(config)# ipv6 route ::/0 {ipv6-address | exit-intf}
Configure a Default Static Route
The example shows an IPv4 default static route configured on R1. With the configuration
shown in the example, any packets not matching more specific route entries are
forwarded to R2 at 172.16.2.2.
R1(config)# ip route 0.0.0.0 0.0.0.0 172.16.2.2
An IPv6 default static route is configured in similar fashion. With this configuration any
packets not matching more specific IPv6 route entries are forwarded to R2 at
2001:db8:acad:2::2
R1(config)# ipv6 route ::/0 2001:db8:acad:2::2
Verify a Default Static Route
The show ip route static command output from R1 displays the contents of the static routes in the routing table.
Note the asterisk (*) next to the route with code ‘S’. The asterisk indicates that this static route is a candidate
default route, which is why it is selected as the Gateway of Last Resort.
Notice that the static default route configuration uses the /0 mask for IPv4 default routes. Remember that the IPv4
subnet mask in a routing table determines how many bits must match between the destination IP address of the
packet and the route in the routing table. A /0 mask indicates that none of the bits are required to match. As long
as a more specific match does not exist, the default static route matches all packets.
Verify a Default Static Route (Cont.)
This example shows the show ipv6 route static command output to display the contents of the
routing table.
Notice that the static default route configuration uses the ::/0 prefix for IPv6 default routes.
Remember that the IPv6 prefix-length in a routing table determines how many bits must match
between the destination IP address of the packet and the route in the routing table. A ::/0 prefix
indicates that none of the bits are required to match. As long as a more specific match does not
exist, the default static route matches all packets.
15.4 Configure Floating
Static Routes
Configure Floating Static Routes
Floating Static Routes
• Another type of static route is a floating static route. Floating static routes are static
routes that are used to provide a backup path to a primary static or dynamic route.
The floating static route is only used when the primary route is not available.
• To accomplish this, the floating static route is configured with a higher administrative
distance than the primary route. The administrative distance represents the
trustworthiness of a route. If multiple paths to the destination exist, the router will
choose the path with the lowest administrative distance.
• By default, static routes have an administrative distance of 1, making them preferable
to routes learned from dynamic routing protocols.
• The administrative distance of a static route can be increased to make the route less
desirable than that of another static route or a route learned through a dynamic
routing protocol. In this way, the static route “floats” and is not used when the route
with the better administrative distance is active.
Configure IPv4 and IPv6 Floating Static Routes
The commands to configure default and floating IP default routes are as follows:
R1(config)# ip route 0.0.0.0 0.0.0.0 172.16.2.2
R1(config)# ip route 0.0.0.0 0.0.0.0 10.10.10.2 5
R1(config)# ipv6 route ::/0 2001:db8:acad:2::2
R1(config)# ipv6 route ::/0 2001:db8:feed:10::2 5
The show ip route and show ipv6 route output verifies that the default routes to R2 are installed in
the routing table. Note that the IPv4 floating static route to R3 is not present in the routing table.
Test the Floating Static Routes
• What would happen if R2 failed? To
simulate this, R2 shuts down both of its
serial interfaces.
• R1 automatically generates syslog
messages for the link going down.
• A look at R1’s routing table would show
the secondary route being used.
15.5 Configure Static Host
Routes
Host Routes
A host route is an IPv4 address with a 32-bit mask, or an IPv6 address with a 128-bit
mask. The following shows the three ways a host route can be added to the routing table:
• Automatically installed when an IP address is configured on the router
• Configured as a static host route
• Host route automatically obtained through other methods (discussed in later courses)
Automatically Installed Host Routes
• Cisco IOS automatically installs a host route, also known as a local host route, when
an interface address is configured on the router. A host route allows for a more
efficient process for packets that are directed to the router itself, rather than for packet
forwarding.
• This is in addition to the connected route, designated with a C in the routing table for
the network address of the interface.
• The local routes are marked with L in the output of the routing table.
Static Host Routes
A host route can be a manually configured static route to direct traffic to a specific
destination device, such as the server shown in the figure. The static route uses a
destination IP address and a 255.255.255.255 (/32) mask for IPv4 host routes, and a /128
prefix length for IPv6 host routes.
The example shows the IPv4 and IPv6 static host route configuration on the Branch router
to access the server.
Branch(config)# ip route 209.165.200.238 255.255.255.255 198.51.100.2

Branch(config)# ipv6 route 2001:db8:acad:2::238/128 2001:db8:acad:1::2
Branch(config)# exit
Branch#
Verify Static Host Routes
A review of both the IPv4 and IPv6 route tables verifies that the routes are active.
Configure IPv6 Static Host Route with Link-Local Next-Hop
For IPv6 static routes, the next-hop address can be the link-local address of the adjacent
router. However, you must specify an interface type and an interface number when using
a link-local address as the next hop, as shown in the example. First, the original IPv6
static host route is removed, then a fully specified route configured with the IPv6 address
of the server and the IPv6 link-local address of the ISP router.

SRWE Module 15new

Uploaded by

Copyright:

Available Formats

SRWE Module 15new

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SRWE Module 15new

Uploaded by

Copyright:

Available Formats

Module 15: IP Static Routing

Switching, Routing, and Wireless Essentials v7.0

Module Objective: Configure IPv4 and IPv6 static routes.

Static Routes Describe the command syntax for static routes.

Configure IP Static Routes Configure IPv4 and IPv6 static routes.

Router(config)# ip route network-address subnet-mask { ip-address

Router(config)# ipv6 route ipv6-prefix/prefix-length {ipv6-address

Most of parameters are identical to the IPv4 version of the command.

R1# show ip route | begin Gateway

R1(config)# ipv6 unicast-routing

R1(config)# ipv6 route 2001:db8:acad:1::/64

R1(config)# ipv6 route 2001:db8:cafe:1::/64

R1(config)# ipv6 route 2001:db8:cafe:2::/64

R1(config)# ipv6 route 2001:db8:acad:1::/64

R1(config)# ipv6 route 2001:db8:cafe:1::/64

R1(config)# ipv6 route 2001:db8:cafe:2::/64

Note: An IPv4 default static route is commonly referred to as a quad-zero route.

R1(config)# ip route 0.0.0.0 0.0.0.0 172.16.2.2

R1(config)# ipv6 route ::/0 2001:db8:acad:2::2

Branch(config)# ip route 209.165.200.238 255.255.255.255 198.51.100.2

You might also like