SteamPac and WaterPac

Unfired Steam and Hot Water Generators

SteamPacs • Vertical or Horizontal • 10 to 415 HP
WaterPacs • Vertical or Horizontal • 200,000 to 14,000,000 BTU/HR
SteamPacs and WaterPacs are designed for
use in Thermal Fluid (Hot Oil) Systems

The heat transfer innovators.

KEY FEATURES
• Can be installed in conjunction with • Can be used with other equipment or
existing thermal fluid systems, thus as a single user
eliminating the need for a separate fired
water heater
• Vertical or horizontal design.
Can provide instantaneous
• Eliminates the need for a stack and hot water or maintain
additional fuel hookup temperature of a hot
water storage tank
• Minimal maintenance
• Each hot water generator
• Automatic temperature control is designed to meet the
• All water side surfaces can be stainless customer’s specifications
or carbon steel and application

• Potable water can be heated without

contamination from minerals

Wherever you need additional hot water in any

laundry or industrial process heating application.
From 200,000 to 14,000,000 BTU/HR.

B
The schematic shows
multiple pieces of equipment piped together
in a closed loop system.

C D

Fulton Thermal Fluid Heater Fulton WaterPac

FULTON STEAMPAC
UNFIRED STEAM GENERATOR
KEY FEATURES
• Wide range and flexibility of steam • Responds quickly to process demands
pressure, 10 to 415 HP with pressures
from 15 to 300 PSIG • Fully automatic operation
• Vertical design uses minimal floor space • Simple, safe, quiet operation
• Wide modulation range (30:1) • High steam quality
• Produces dry steam (95% minimum)
Very dry steam (99.5%) upon request
• If system runs dry, it causes no harm to
the SteamPac
• Low installation costs. No costly fuel
hookups or stack required
• Unfired pressure vessel, possibly
eliminating requirements for a
stationary attendant
• Low thermal inertia - full steam quickly
from the start
• Custom clean steam systems available

This schematic is a concept only. Fulton thermal fluid equipment

It is not a P & ID drawing or can be designed into any
an engineered system. E process system needing heat,
steam, or hot water.
A Fulton Thermal Fluid Heater
(Hot oil temperatures up to 750°F)

B Fulton Patented Deaerator

Thermal/Buffer Expansion Tank

C Users: Single or multiple users can

be designed into a thermal fluid
system. Autoclaves, fryers, reactors,
ironers, ovens, open baths, calendar
roll equipment, platens, presses,
anywhere process heat, steam, and
hot water is used

D Fulton WaterPac Horizontal or

Vertical Design Unfired Hot Water
C Generators

Fulton SteamPac E Fulton SteamPac Horizontal or

Available in Horizontal or Vertical Design Unfired Steam
Vertical Configuration Generators
 Specifications • Fulton Horizontal SteamPacs from 70 to 415 HP
Models FT 070XH 100XH 150XH 180XH 200XH 250XH 300XH 350XH 415XH
Steam Output* LB/HR 2,415 3,450 5,175 6,210 6,900 8,625 10,350 12,075 14,392
KG/HR 1,096 1,565 2,347 2,817 3,130 3,912 4,695 5,477 6,528
Input BTU/HR (1000) 2,343 3,347 5,021 6,025 6,694 8,368 10,041 11,715 13,891
KCAL/HR (1000) 590 843 1,265 1,518 1,687 2,108 2,530 2,952 3,500
Flow Rate GPM 160 228 342 411 456 570 684 798 946
M3/HR 37 52 78 94 104 130 156 182 215
B *From 0 psig and at 212°F (100°C). Steam Output is based on a minimum thermal fluid temperature of 550°F (288°C)

A
Dimensions • Fulton Horizontal SteamPacs from 70 to 415 HP
Models FT 070XH 100XH 150XH 180XH 200XH 250XH 300XH 350XH 415XH
(A) Width IN 42 48 48 48 60 60 60 60 60
MM 1,067 1,219 1,219 1,219 1,524 1,524 1,524 1,524 1,524
(B) Length IN 108 144 144 144 150 150 160 160 160
C
MM 2,743 3,658 3,658 3,658 3,810 3,810 4,064 4,064 4,064
(C) Height IN 84 98 98 98 98 98 98 98 98
MM 2,134 2,489 2,489 2,489 2,489 2,489 2,489 2,489 2,489
All dimensions are based on 550°F thermal fluid temperature and are subject to change based on specific customer requirements.

Horizontal SteamPac

Specifications • Fulton Vertical SteamPacs from 10 to 100 HP

Models FT 010X 015X 020X 030X 040X 050X 075X 100X
Steam Output* LB/HR 345 517 690 1,035 1,380 1,725 2,587 3,450
A KG/HR 157 235 313 470 626 783 1,174 1,565
Input BTU/HR (1000) 335 502 669 1,017 1,339 1,674 2,678 3,347
KCAL/HR (1000) 84 126 169 256 337 422 675 843
Flow Rate GPM 23 35 46 69 92 114 171 228
M3/HR 5.2 8 10.5 16 21 26 39 52
B
*From 0 psig and at 212°F (100°C). Steam Output is based on a minimum thermal fluid temperature of 550°F (288°C)

Dimensions • Fulton Vertical SteamPacs from 10 to 100 HP

Models FT 010X 015X 020X 030X 040X 050X 075X 100X
(A) Width IN 84 72 92 92 92 92 92 92
MM 2,134 1,829 2,337 2,337 2,337 2,337 2,337 2,337
(B) Length IN 72 84 72 72 72 72 92 92
MM 1,829 2,134 1,829 1,829 1,829 1,829 2,337 2,337
(C) Height IN 125 125 125 125 143 143 169 169
C MM 3,175 3,175 3,175 3,175 3,632 3,632 4,293 4,293
All dimensions are based on 550°F thermal fluid temperature and are subject to change based on specific customer requirements. Vertical
SteamPac dimensions include feedwater tank and blowdown separator.

All SteamPac accessories including feedwater tanks, feedwater pumps,

blowdown separators, chemical feed and water softeners are available
Vertical SteamPac from Fulton.

The heat transfer innovators.

Fulton Thermal Corporation www.fulton.com
972 Centerville Road, Pulaski, NY 13142
Call: (315) 298-5121 • Fax: (315) 298-6390 steam_waterpac-bro-2011-0804