See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/267195951

Laboratory and HEC-RAS simulations of a single-step weir

Article · December 2013

CITATIONS READS
4 386

1 author:

Jihan Mahmood Qasim

University of Duhok
6 PUBLICATIONS   12 CITATIONS   

SEE PROFILE

All content following this page was uploaded by Jihan Mahmood Qasim on 27 October 2014.

The user has requested enhancement of the downloaded file.

 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

LABORATORY AND HEC-RAS SIMULATIONS OF A SINGLE-STEP WEIR

Jihan Mahmood Qasim
Water Resources Engineering, Faculty of Engineering and Applied Sciences, University of Duhok, Duhok, Iraq
E-Mail: [email protected]

ABSTRACT
The River Analysis System (HEC-RAS) software was used to simulate the free flow over the broad-crested
single-step weir. The software was used to compute the water surface profile, determine the location of the hydraulic jump,
and establish the head-discharge relationship for the weir. The simulation results were verified by a series of laboratory
measurements using a horizontal flume 5 m long, 0.45 m deep and 0.30 m wide. The tested weir had the following
dimensions: total length was 48 cm; length of the downstream step of the weir was 24 cm; total height was 24 cm; height
of the downstream step of the weir was 12 cm. Different inflow rates were applied to the weir for tail water depths of 6, 8,
10, 12 and 14 cm under free flow conditions. It was found that HEC-RAS could capture the overall features of the flow
profile over the weir with reasonable accuracy. HEC-RAS could also determine the location of the hydraulic jump. It also
produced a head-discharge relationship well close to the measured data. Besides, HEC-RAS was found easy to use for this
specific flow problem and performed the computations in a short time.

Keywords: single-step weir, HEC-RAS, water surface profile, head-discharge relationship, hydraulic jump, free flow.

1. INTRODUCTION deltaic environments. It was noticed that HEC-RAS had a

Today with the improved numerical algorithms general tendency to overestimate water levels during high
and the increasing computing power, using software flows and underestimate during low flows. Toombes and
became essential for solving hydraulic problems. The Chanson (2011) tested the capability of HEC-RAS to
software can be used as an effective tool for many simulate gradually and rapidly varied flows. Two physical
purposes, such as to evaluate the designs of existing and models were made to verify the simulation results. The
proposed structure, predict structure performance under first was a streamlined weir and the second was a channel
different flow conditions, and perform hydraulic controlled with upstream and downstream gates. As to the
calculations for the entire flow field at a cost and time less weir flow problem, it was found that HEC-RAS achieved
than physical modelling. good flow profiles across the weir at low flows. For the
A large number of computer models are available high-flow case, significant differences were observed over
for simulating the hydraulic problems. The models are the weir. However, profiles upstream and downstream of
usually different in their complexity and reliability. It is the weir were predicted with good accuracy. For the
therefore important that engineers have sufficient channel flow problem, the HEC-RAS results were shown
knowledge of the abilities and limitations of the models so to be in good agreement with the measurements. It was
as to select the suitable software for solving specific flow concluded that HEC-RAS could model subcritical and
problems. supercritical flows, and predict the location of a hydraulic
One of the most common computer models is the jump with reasonable accuracy.
one-dimensional River Analysis System (HEC-RAS) The preceding review shows that HEC-RAS has
developed by Hydrologic Engineering Center of the US mostly been used to model floodplains and channels and it
Army Corps of Engineers (USACE). This model can has rarely been evaluated to describe weir flow problems
perform computations on 1-D steady and unsteady river (to the best of author’s knowledge).
hydraulics, sediment transport, and water temperature In the present study, the one-dimensional steady-
analysis. Effects of bridges, culverts, spillways, drops and flow module of HEC-RAS was used to develop the water
weirs may also be considered in the computations surface profile, determine the location of the hydraulic
(USACE, 2010). jump, and produce the head-discharge relationship for the
For the purpose of this study, the studies that broad-crested single-step weir.
have evaluated the performance of HEC-RAS are The performance of this numerical model was
reviewed herein. HEC-RAS is a very commonly used evaluated using a series of laboratory experiments that
program, but its performance has rarely been evaluated. incorporated different free flow situations. The effects of
Gonzalez (1999) used HEC-RAS to determine the variation of parameters such as the flow rate and the
maximum capacity of a floodway channel of a river. It was tailwater depth were investigated. It was a major purpose
noticed that HEC-RAS required few input data, but of the present study to discover the advantages and
presented a simplified view of the flow pattern with limitations of HEC-RAS for simulating the flow over a
complex channel geometry. Cook (2008) also used HEC- stepped hydraulic structure.
RAS in floodplain mapping and hydraulic modelling of
two river reaches. It was found that the simulation in 2. THE SINGLE-STEP WEIR
HEC-RAS was easy and quick. Siddique-E-Akbor et al. Stepped weirs differ slightly from vertical weirs.
(2011) used HEC-RAS for estimating river water levels in The addition of stepped downstream faces allows for some

1005
 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

energy to dissipate at each level. Stepped weirs are

appropriate for small structures in waters without heavy
sediment loads. Where larger structures are required or
bearing capacity of soils is limited, sloped weirs are most
appropriate (gabions.net).
The free flow over the single-step weir is shown
in Figure-1. The head-discharge relationship for a single-
step broad-crested weir with rectangular control section is
given by (Hussein et al., 2010):

Figure-2. The experimental arrangement.

where The tested weir, shown in Figure-3, has the
following dimensions: L = 48 cm, L1 = 24 cm, P = 24 cm,
L total length of the weir (m) P1 = 12 cm.
L1 length of the downstream step of the weir (m)
P total weir height (m)
P1 height of the downstream step of the weir (m)
Q total flow rate (m3/sec)
Cd discharge coefficient
B width of the channel (m)
g acceleration due to gravity (m/sec2)
H total head over the crest of the weir (m)

Figure-3. The tested single-step weir.

The weir was setup inside the flume using

Plexiglas plates of 6 mm thickness. The parts of the weir
were joined together and to the flume bed and sides by
silicone sealant. The centerline of the weir was placed at
2.61 m from the upstream end of the flume.
Figure-1. Free flow over single-step weir. The weir was operated under various free flow
conditions. Different flow rates were investigated for
3. THE EXPERIMENTAL WORKS tailwater depths, dtw = 6, 8, 10, 12 and 14 cm.
The single-step weir model was installed in a
horizontal rectangular flume. The flume was 5m long, 4. DESCRIPTION OF THE RIVER ANALYSIS
0.3m wide and 0.45m deep. Water entered into the flume SYSTEM (HEC-RAS)
from the head tank and dropped freely in a sump tank at The steady-flow module of HEC-RAS can model
the other end of the flume. The experimental arrangement the flow surface profiles for supercritical, subcritical, and
is shown in Figure-2. A ruler for measuring the tailwater mixed flow regimes in a single river reach or a system of
depth was put at the downstream end of the flume. An channels (USACE, 2010).
electro-magnetic flow meter was used to measure the The water surface profile between two cross
inflow rate. The water surface elevations were measured sections is computed based on the solution of the energy
by using two manual point gauges. The datum was set at equation, which is defined as:
the bed level of the flume.

where

1006
 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

Zb1, Zb2 = bed elevation at the cross sections (m)

d1, d2 = depth of flow at the cross sections (m)
V1, V2 = average velocity of flow at the cross sections
(m/sec)
α1, α2 = velocity weighting coefficients at the cross
sections where
he = energy head loss (m)
n = Manning’s roughness coefficient (sec/m1/3)
The above terms are illustrated in Figure-4. This Q1, Q2 = discharge at cross sections (m3/sec)
equation is solved with an iterative procedure called the A1, A2 = flow area of cross sections (m2)
standard step method. Energy equation is valid for uniform R1, R2 = hydraulic radius of cross sections (m)
and gradually varied flow situations. These situations
signify that the streamlines are parallel, that is, the Flow contraction or expansion due to changes in
pressure distribution over the channel section is the channel cross section is a common cause of energy
hydrostatic, and that the channel is prismatic with a small losses between two cross sections within a reach. HEC-
bed slope. RAS assumes that a flow contraction occurs when the
velocity head increases in the downstream direction; and
an expansion occurs when the velocity head decreases
(USACE, 2010).

5. RUNNING THE HEC-RAS PROGRAM

Work with the HEC-RAS program was started by
creating a project. Then two types of data were needed to
be entered into the project:

5.1. Geometric data

The schematic of the channel to be modelled was
drawn. Then data of the cross sections along the channel
Figure-4. Terms of the energy equation (USACE, 2010). were entered. These data include the station and elevation
coordinates, reach length, channel width at the sections,
The energy head loss includes friction losses and Manning’s coefficient, and contraction/expansion
contraction or expansion losses. The equation for the coefficient.
energy head loss is as follows: In the present study, 74 cross sections were
created for the flow problem to perform the simulation
process with the desired accuracy. Manning’s n coefficient
was set within the allowable range (0.009-0.013) (Chow,
1959) for the channel used in the laboratory work.
where
5.2. Steady flow data
L = discharge weighted reach length (m) These data include the number of flow profiles to
= representative friction slope between two cross be computed for the weir, the flow rates, and the boundary
conditions. The laboratory data of the flow rates, the flow
sections
depths, and the tailwater depths were used as boundary
C = contraction or expansion losses coefficient
conditions in the simulations.
Once the necessary data were entered, the
The discharge weighted reach length is calculated as:
program became ready to run a steady flow simulation.
There were three options for the computation of the flow
surface profile in the program: subcritical, supercritical,
and mixed flow regime. The flow profile over the single-
step weir is characterized by a flow change from
where Llob, Lch and Lrob are the reach lengths for flow in the
subcritical to supercritical due to the geometry of the weir,
left overbank, main channel and right overbank,
and from supercritical to subcritical due to the hydraulic
respectively; and , and are the average flow
jump. Therefore, the mixed flow regime was adopted.
rates between two cross sections for the left overbank, After the computations were finished, the generated water
main channel and right overbank, respectively. surface profiles could be viewed in different tabular and
The friction slope for the reach is computed using graphical forms within the HEC-RAS program.
the average conveyance equation as:

1007
 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

6. CALIBRATING THE HEC-RAS PROGRAM 7. COMPARISON OF THE COMPUTED AND THE

The ability of the HEC-RAS model to predict the OBSERVED DATA
characteristics of flow over the single-step weir was tested In order to discover the advantages and
by comparing the numerical simulation results against the limitations of the software for modelling this specific flow
corresponding data from the laboratory experiments. The problem, a detailed evaluation is performed as follows:
accuracy of HEC-RAS results was increased by calibrating
the program. 7.1. Water surface profile
The controlling parameter affecting the The water surface profiles generated by HEC-
performance of the HEC-RAS model was the Manning’s RAS are compared to the corresponding observed profiles.
roughness coefficient. The value of this coefficient was A sample of the data is shown in Figure-5.
adjusted to fix unstable runs until the computed water
surface profiles best represented the observed flow
conditions.

Figure-5(a). Computed and observed water surface profiles over a single-step weir.

1008
 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

Figure-5(b). Computed and observed water surface profiles over a single-step weir (continued).

1009
 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

It may be seen from the above figures that HEC- of the channel, except when the jump occurs at the toe of
RAS well predicted the water surface profile upstream of the weir at low flow rates. HEC-RAS represents the jump
the weir. The HEC-RAS profile is also in good agreement as a straight line.
with the observed profile over the upper part of the weir. However, reviewing the second case of Figure-
However, it may also be observed that HEC-RAS 5.a shows that HEC-RAS made an improper prediction of
could not simulate the curvature of the water profile at the the jump location. The reason behind this unstable
hydraulic drops where the water falls from the upper part performance is not clear. The prediction of the water level
of the weir to the lower part, and also from the lower part in this case is still correct.
of the weir to the channel bed. HEC-RAS could neither
describe the impact of jet occurring after these hydraulic 7.3. Head-discharge relationship
drops. This behaviour is believed to be due to the marked The head-discharge relationship is established by
curvature of the streamlines, and the difficulty of forming plotting the total head over the weir crest against the
a smooth transition. discharge. The experimentally observed results and the
predicted head-discharge relationship for the weir are
7.2. Location of the hydraulic jump shown in Figure-6.
HEC-RAS proved its ability to predict accurately
the occurrence of the hydraulic jump on the horizontal bed

Figure-6. The observed and predicted head-discharge relationship of a single-step weir.

The figure shows that the results produced by 7.5. Ease of use
HEC-RAS are in good agreement with the laboratory In addition to the run time, inputting data and
results. Thus, HEC-RAS possess considerable accuracy in displaying the results are other parts of the simulation
estimating this relationship for such stepped hydraulic process. From this perspective, HEC-RAS with its simple
structure. interface windows was found easy to create and modify
the geometric data file for this specific flow problem.
7.4. Computational time Besides, it is apparent from the running procedure
The theoretical bases and the solution techniques of HEC-RAS, illustrated previously, that it requires no
of the HEC-RAS model are determining factors of the initial conditions and also demands few boundary
time of computations. In the present simulations, HEC- conditions data, resulting in significant savings in effort
RAS spent a maximum time of less than (30) seconds to and time.
compute the water surface profiles over the weir. However, HEC-RAS offers simple and not quite
This significantly short run time is owed to the descriptive graphs, but it offers tabular forms that are quite
governing equations and solution approaches followed by flexible for viewing the results.
HEC-RAS. The 1-D steady-flow component of HEC-RAS
is based on the energy equation, which involves a number 8. CONCLUSIONS
of simplifying approximations that help reduce The1-D steady-flow HEC-RAS module was used
computational complexity. Furthermore, the energy to describe the water surface profile, determine the
equation is solved by the standard step method, which is a location of the hydraulic jump, and produce the head-
relatively simple iterative approach applied easily to 1-D discharge relationship for the single-step weir.
grids and, hence, contributes to the short computation Performance of the numerical model was evaluated by free
time. flow laboratory tests on the weir.

1010
 VOL. 8, NO. 12, DECEMBER 2013 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2013 Asian Research Publishing Network (ARPN). All rights reserved.

www.arpnjournals.com

From analysing and comparing the HEC-RAS Siddique-E-Akbor A.H.M. and others. 2011. Inter-
results to the observed results, the following conclusions comparison study of water level estimates derived from
may be drawn: hydrodynamic-hydrologic model and satellite altimetry for
a complex deltaic environment. Remote Sensing of
a) HEC-RAS could compute the water surface profile Environment. 115: 1522-1531.
upstream of the single-step weir very well.
b) HEC-RAS could simulate accurately the water surface Toombes L. and Chanson H. 2011. Numerical Limitations
profile over the upper part of the single-step weir. of Hydraulic Models. The 34th International Association
c) HEC-RAS could not simulate the curved flow past the for Hydraulic Research World Congress, Brisbane,
vertical faces of the single-step weir. Australia. pp. 2322-2329.
d) HEC-RAS could not simulate the impact of jet past
the vertical faces of the single-step weir. U.S. Army Corps of Engineers. 2010. HEC-RAS River
e) HEC-RAS could accurately determine the location of Analysis System, Hydraulic Reference Manual, Version
the hydraulic jump on the channel bed when the jump 4.1, Hydrologic Engineering Center, Davis, California,
was not at the toe of the weir. USA.
f) HEC-RAS presented precise results of the head-
discharge relationship for the single-step weir. http://www.gabions.net/news.html.
g) HEC-RAS is easy and friendly to use. It demands few
boundary conditions data and required no initial
conditions. The geometric data file for this specific
flow problem was also found easy to create and
modify.
h) HEC-RAS computes the one-dimensional free-flow
surface profiles very quickly. The computation time
was less than a half minute.

However, the performance of the steady-flow

module of HEC-RAS on the single-step weir is expected
to be the same for a multi-step weir flow problem.

ACKNOWLEDGEMENTS
The author owes recognition to the water
resources engineers Parizad Ahmed Hussein, Sipel Ameer
Fize and Jihan Moayad Fariq, for their assistance in the
laboratory works.

REFERENCES

Chow V. T. 1959. Open-Channel Hydraulics, McGraw-

Hill, New York, USA. pp. 30, 31 and 110.

Cook A. C. 2008. Comparison of One-Dimensional HEC-

RAS with Two-Dimensional FESWMS Model in Flood
Inundation Mapping. M.Sc thesis, Purdue University,
USA.

Hussein H. H., Juma I. A. K. and Shareef S. J. S. 2010.

Improving the Hydraulic Performance of Single Step
Broad-Crested Weirs. Iraqi Journal of Civil Engineering.
7(1): 1-12.

Gonzalez N. S. 1999. Two-Dimensional Modelling of the

Red River Floodway. M.Sc thesis, University of Manitoba,
Canada.

Rickard C., Day R. and Purseglove J. 2010. River Weirs-

Good Practice Guide.

1011
View publication stats