MazzellaCatalog13 RiggingHardware LR

Hardware
Mazzella Lifting Technologies Progressive Crane Mazzella Crane Service Indusco Wire Rope & Supplies
Phone: 800-362-4601 Phone: 800-83-CRANE Phone: 877-96-CRANE Phone: 410-727-0665
www.mazzellalifting.com www.progressivecrane.com www.mazzellacraneservice.com www.induscowire.com
354
MazzellaCatalog13_Hardware.indd 354 7/3/13 9:40 AM

Rigging & Lifting Hardware
Cranes / Jibs
Overhead

We offer one of the largest and most complete inventories
of rigging and lifting products in the country from some
of the largest manufactures in the world.
Hoists
Some of the products we stock are:
■ Hoist rings—standard and metric

■ Shackles—all types, sizes and finishes from
Services
1/4 ton to over 1,000 tons
■ Master rings / links—all sizes, types and finishes
■ Hooks—swivel, eye, choker, self-locking and weld-on
■ Turnbuckles and swivels
Engineered
Products
We also stock many other rigging hardware items. If you
can’t find a standard item to meet your specific needs,
inquire about custom rigging and lifting hardware.
All hardware products meet the ASME B30.26 specification.
Slings
Hardware
Products
Lifting
Rope
Wire
Cordage
Securement
Load
Contractors
Supply
Protection
J Henry Holland Alabama Sling Center Tennessee Sling Center KCI Crane Service
Phone: 757-460-3300 Phone: 205-744-0230 Phone: 901-345-8918 (Memphis) Phone: 205-345-4701
Fall
www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

www.tennesseeslingcenter.com
355

Rigging Hardware Index Jaw End Swivels............................................404
Tapered Roller Thrust Bearing Swivels..........405 - 406
Angular Contact Bearing Swivels...................407
Warning Elements..........................................357 Sliding Choker Hooks.....................................408
Screw Pin Anchor Shackles...........................358 Snap Hooks....................................................408
Screw Pin Chain Shackles.............................359 Replacement Hooks.......................................408
Round Pin Anchor Shackles...........................360 Sorting Hooks.................................................408
Round Pin Chain Shackles.............................361 Barrel Hooks...................................................408
Alloy Screw Pin Shackles...............................362 Eye Grab Hooks.............................................409
Screw Pin Wide Body Shackles.....................363 Clevis Grab Hooks.........................................409
Bolt Type Anchor Shackles.............................364 Eye Slip Hooks...............................................410
Bolt Type Chain Shackles...............................365 Clevis Slip Hooks...........................................410
Alloy Bolt Type Shackles................................366 Golden Gate® Hooks (Bullard)........................411 - 412
Wide Body Shackles......................................367 Hook Data Form.............................................413
Theatrical Shackles........................................368 Weld-On Excavator Hooks.............................414
Midland Anchor Shackles...............................369 Eye Type Self-Locking Hooks.........................414
Midland Chain Shackles.................................370 Swivel Bronze Bushing
Alloy Sheet Pile Shackles...............................371 Self-Locking Hooks..................................415
Sheet Pile Shackle Ground Release..............371 Weld-On Pivot Link.........................................415
Alloy Towing Shackles....................................372 Shank Hooks..................................................416
Galvanized Bolt Type Chain Shackles............372 Design-A-Crane Hook....................................417
Stainless Steel Shackles................................373 Standard Alloy J-Hooks..................................418
Design-A-Shackle...........................................373 Design-A-J-Hook............................................419
Swivel Hoist Rings..........................................374 Latch Kits........................................................420 - 424
UNC Swivel Hoist Rings.................................375 Turnbuckles....................................................425 - 429
Metric Swivel Hoist Rings...............................376 Turnbuckle Data.............................................430 - 431
Heavy Lift Swivel Hoist Rings.........................377 STARPOINT Eye Bolts...................................432
Safety Engineered Hoist Rings......................378 Forged Eye Bolts............................................433
Heavy Duty® Hoist Rings................................378 Metric Eye Bolts.............................................434
Side Pull Hoist Rings......................................379, 380, . Stainless Steel Eye Bolts...............................434
.................................................................381 Regular Nut Eye Bolts....................................435
E-Z® Torque Hoist Rings.................................379 Shoulder Nut Eye Bolts..................................436
Stainless Steel Safety Hoist Rings ................380 Stainless Steel Swivels & Links......................437 - 438
Safety Swivel Hoist Rings .............................380 Stainless Steel Turnbuckles...........................439
Traditional Center Pull Hoist Rings ................381 G-Link™ Sling Connector...............................440
Shackle-LokTM Hoist Ring...............................381 Proof Coil Chain—Grade 30...........................441,
Load Rings: Bolted & Welded.........................382 - 386 .................................................................446 - 447
Malleable Clips—Zinc Plated.........................387 Carbon Chains...............................................442 - 445
Alloy Pear Shaped Links................................388 Grade 30 / Winch Hooks................................445
Weldless Sling Links.......................................388 Lockdown Chain.............................................447
Weldless End Links........................................389 Weldless Chain...............................................448
Weldless Rings...............................................389 Clevis Links....................................................449, 450
Alloy Master Links..........................................390 Quick Link.......................................................450
Open Pear Master Links.................................391 Repair Link.....................................................450
Wide Master Links .........................................392 Cold Shut........................................................451
Design-A-Link.................................................393 Welded Ring...................................................451
Standard Wire Rope Thimbles.......................394 S Hooks..........................................................451, 452
Extra Heavy Wire Rope Thimbles..................394 Snap Links......................................................452
Open Pattern Wire Rope Thimbles.................395 Double Clevis—Twin Link...............................452
Solid Wire Rope Thimbles..............................395 Replacement Links.........................................453
Special Thimbles............................................396 - 397
Boom Pendant Thimbles................................398 Warnings
Special Thimbles—Stainless Steel.................399 Product Warnings...........................................454 - 461
SHUR-LOC® Swivel Hooks.............................400
Eye Hooks......................................................401 For the complete catalog index,
Swivel Hooks..................................................402 refer to the front of the book.
Chain / Regular Swivels.................................403
356

Warning Elements Signal Words
Cranes / Jibs
Overhead
Let’s turn to the basic elements and formats of our warnings. In our warnings, a “signal word” is used to attract
In most of our warnings, four basic elements or types of attention of the user to the warning. As indicated below,
information are provided: another purpose of the signal word is to identify the
level of risk or hazard involved. Sometimes, the signal
word will be accompanied by a “safety alert symbol,”
Hoists
1. A “Signal Word,” such as “DANGER”, “WARNING”
or “CAUTION.” This word is meant to attract the such as an exclamation point inside a triangle. The signal
attention of the user to the warning statement. The word will always appear within a box or panel separated
signal word also identifies the degree of potential from the remainder of the warning by a border and, in some
danger or risk in using the product. cases, may have a contrasting background color, such as
Services
red, orange or yellow. The majority of our warnings use
2. A “Hazard Statement,” such as “FAILURE TO USE the signal words:
TACKLE BLOCK CORRECTLY MAY CAUSE LOAD
TO SLIP OR FALL.” This statement is meant to
DANGER
Engineered
inform or remind the user of factors involved in the
Products
task or work environment that can create a hazard.
3. A “Consequence Statement,” such as “FAILURE

TO FOLLOW APPLICATION INSTRUCTIONS MAY This indicates a situation in which a hazard is
RESULT IN SERIOUS INJURY OR DEATH.” This imminent and will result in a high probability of
Slings
statement is meant to inform or remind the user serious injury or death.
that failure to avoid the hazard can have harmful
consequences.
4. WARNING
Hardware
An “Instruction Statement,” such as “PREPARE
WIRE ROPE TERMINATION ONLY AS
INSTRUCTED.” This statement is meant to
inform or remind the user of the proper This indicates a potential hazardous situation which
steps or procedures for using the product could result in some probability of serious injury or death.
Products
safely and avoiding the hazard.
Lifting
CAUTION
Rope
Wire
This indicates a potential hazardous situation which
could result in minor injury or moderate injury.
Cordage
Our warnings use these signal words for alerting
product users to potential hazards, which can
result in personal injury or death. For hazards involving
potential damage to property, we use other signal
Securement
words, such as “IMPORTANT” or “NOTICE.”

Load
Contractors
Supply
Protection
Fall

357

G-209 / S-209 Screw Pin
Anchor Shackles
G-209 Screw pin anchor shackles meet the performance
requirements of Federal Specification RR-C-271F Type IVA,
Grade A, Class 2, except for those provisions required of
the contractor.
■ Capacities 1/3 thru 55 metric tons, grade 6.

■ Forged - Quenched and Tempered, with alloy pins.
■ Working Load Limit and grade “6”
permanently shown on every shackle.
■ Hot Dip galvanized or Self Colored.
■ Fatigue rated.
■ Shackles 25t and larger are RFID EQUIPPED.
■ Shackles can be furnished proof tested with certificates
to designated standards, such as ABS, DNV, Lloyds
or other certification. Charges for proof testing
and certification available when requested at the
time of order.
■ Approved for use at -40°C (-40°F) to
204°C (400°F).
■ 2t through 25t bow and screw pin are Certified to
meet charpy impact testing of 42 joules (31 ft.-Ibs.) ■ Crosby 2t through 25t G209 anchor shackles are type
min. ave. at -20°C (-4°F). approved to DNV Certification Notes 2.7-1 - Offshore
■ All shackles are Quenched and Tempered and can Containers. These Crosby shackles are statistical proof
meet DNV impact requirements of 42 joules (31 ft.-Ibs.) and impact tested. The tests are conducted by Crosby
at -20°C (-4°F). and 3.1 test certification is available upon request.
■ Meets or exceeds all requirements of ASME B30.26. ■ Look for the Red Pin®…the mark of genuine
■ Type Approval and certification in accordance with Crosby quality.
ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide
for Certification of Cranes.
Working Toler-
Nominal Stock Weight Dimensions
Load ance
Size No. Each (in.)
Limit +/-
in. t* G-209 S-209 lbs. A B C D E F G H L M P C A
3/16 1/3 1018357 – .06 .38 .25 .88 .19 .60 .56 .98 1.47 .16 1.14 .19 .06 .06
1/4 1/2 1018375 1018384 .10 .47 .31 1.13 .25 .78 .61 1.28 1.84 .19 1.43 .25 .06 .06
5/16 3/4 1018393 1018400 .19 .53 .38 1.22 .31 .84 .75 1.47 2.09 .22 1.71 .31 .06 .06
3/8 1 1018419 1018428 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.02 .38 .13 .06
7/16 1-1/2 1018437 1018446 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 .31 2.37 .44 .13 .06
1/2 2 1018455 1018464 .72 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 3-1/4 1018473 1018482 1.37 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
3/4 4-3/4 1018491 1018507 2.35 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 .50 3.97 .81 .25 .06
7/8 6-1/2 1018516 1018525 3.62 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 .50 4.50 .97 .25 .06
1 8-1/2 1018534 1018543 5.03 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 .56 5.13 1.06 .25 .06
1-1/8 9-1/2 1018552 1018561 7.41 1.81 1.25 4.25 1.16 2.91 2.69 5.16 7.47 .63 5.71 1.25 .25 .06
1-1/4 12 1018570 1018569 9.50 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 .69 6.25 1.38 .25 .06
1-3/8 13-1/2 1018598 1018605 13.53 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 .75 6.83 1.50 .25 .13
1-1/2 17 1018614 1018623 17.20 2.38 1.63 5.75 1.54 3.88 3.63 6.88 10.00 .81 7.33 1.62 .25 .13
1-3/4 25 1018632 1018641 27.78 2.88 2.00 7.00 1.64 5.00 4.19 8.86 12.34 1.00 9.06 2.25 .25 .13
2 35 1018650 1018669 45.00 3.25 2.25 7.75 2.08 5.75 4.81 9.97 13.68 1.22 10.35 2.40 .25 .13
2-1/2 55 1018678 1018687 85.75 4.13 2.72 10.50 2.71 7.25 5.69 12.87 17.84 1.38 13.00 3.13 .25 .13
* Note: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit.
358

Cranes / Jibs
Overhead
Chain Shackles
G-210 Screw pin chain shackles meet the performance
requirements of Federal Specification RR-C-271F, Type IVB,
Hoists
the contractor.

■ Working Load Limit and grade “6”
Services
permanently shown on every shackle.
■ Fatigue rated.
Engineered
Products
or other certification. Charges for proof testing
and certification available when requested at the
time of order.
■ Approved for use at -40°C (-40°F) to 204°C (400°F).
Slings
■ 2t through 25t bow and screw pin are Certified to
meet charpy impact testing of 42 joules (31 ft.-Ibs.) min.
ave. at -20°C (-4°F). ■ Crosby 2t through 25t G209 anchor shackles are type
■ All shackles are Quenched and Tempered and can approved to DNV Certification Notes 2.7-1 - Offshore
Hardware
meet DNV impact requirements of 42 joules (31 ft.-Ibs.) Containers. These Crosby shackles are statistical proof
at -20°C (-4°F). and impact tested. The tests are conducted by Crosby
■ Meets or exceeds all requirements of ASME B30.26. and 3.1 test certification is available upon request.
■ Type Approval and certification in accordance with ■ Look for the Red Pin®…the mark of genuine
ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide Crosby quality.
Products
for Certification of Cranes.
Lifting
Working
Nominal Stock Weight Dimensions Tolerance
Load
Size No. Each (in.) +/-
Limit
Rope
Wire
in. t* G-210 S-210 lbs. A B C D E F G K L M G A
1/4 1/2 1019150 1019169 .11 .47 .31 .25 .25 .97 .62 .97 1.59 .19 1.43 .06 .06
5/16 3/4 1019178 1019187 .17 .53 .38 .31 .31 1.15 .75 1.07 1.91 .22 1.71 .06 .06
3/8 1 1019196 1019203 .28 .66 .44 .38 .38 1.42 .92 1.28 2.31 .25 2.02 .13 .06
7/16 1-1/2 1019212 1019221 .43 .75 .50 .44 .44 1.63 1.06 1.48 2.67 .31 2.37 .13 .06
Cordage
1/2 2 1019230 1019249 .59 .81 .63 .50 .50 1.81 1.18 1.66 3.03 .38 2.69 .13 .06
5/8 3-1/4 1019258 1019267 1.25 1.06 .75 .63 .63 2.32 1.50 2.04 3.76 .44 3.34 .13 .06
3/4 4-3/4 1019276 1019285 2.63 1.25 .88 .81 .75 2.75 1.81 2.40 4.53 .50 3.97 .25 .06
7/8 6-1/2 1019294 1019301 3.6 1.44 1.00 .97 .88 3.20 2.10 2.86 5.33 .50 4.50 .25 .06
1 8-1/2 1019310 1019329 4.75 1.69 1.13 1.00 1.00 3.69 2.38 3.24 5.94 .56 5.13 .25 .06
Securement
1-1/8 9-1/2 1019338 1019347 6.75 1.81 1.25 1.25 1.13 4.07 2.68 3.61 6.78 .63 5.71 .25 .06
1-1/4 12 1019356 1019365 9.06 2.03 1.38 1.38 1.25 4.53 3.00 3.97 7.50 .69 6.25 .25 .13
Load
1-3/8 13-1/2 1019374 1019383 11.63 2.25 1.50 1.50 1.38 5.01 3.31 4.43 8.28 .75 6.83 .25 .13
1-1/2 17 1019392 1019409 15.95 2.38 1.63 1.62 1.50 5.38 3.62 4.84 9.05 .81 7.33 .25 .13
1-3/4 25 1019418 1019427 26.75 2.88 2.00 2.12 1.75 6.38 4.19 5.78 10.97 1.00 9.06 .25 .13
2 35 1019436 1019445 42.31 3.25 2.25 2.36 2.10 7.25 5.00 6.77 12.74 1.13 10.35 .25 .13
Contractors
2-1/2 55 1019454 1019463 71.75 4.12 2.75 2.63 2.63 9.38 5.68 8.07 14.85 1.38 13.00 .25 .25
Supply
Protection
Fall

359

G-213 / S-213 Round Pin
Anchor Shackles
G-213 Round pin anchor shackles meet the performance
the contractor.
■ Capacities 1/2 through 35 metric tons.

■ Working Load Limit permanently shown on
every shackle.
■ Fatigue rated.
or other certification. Charges for proof testing and
certification available when requested at the time
of order.
■ Shackles are Quenched and Tempered and can meet
DNV impact requirements of 42 joules (31 ft.-Ibs.) at
-20°C (-4°F).
■ Look for the Red Pin®…the mark of genuine
Crosby quality.
Working
Load
Limit
in. t* G-213 S-213 lbs. A B C D E F G H N P C A
1/4 1/2 1018017 1018026 .13 .47 .31 1.13 .25 .78 .61 1.28 1.84 1.34 .25 .06 .06
5/16 3/4 1018035 1018044 .18 .53 .38 1.22 .31 .84 .75 1.47 2.09 1.59 .31 .06 .06
3/8 1 1018053 1018062 .29 .66 .44 1.44 .38 1.03 .91 1.78 2.49 1.86 .38 .13 .06
7/16 1-1/2 1018071 101050 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 2.13 .44 .13 .06
1/2 2 1018099 1018106 .71 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 2.38 .50 .13 .06
5/8 3-1/4 1018115 1018142 1.50 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 2.91 .69 .13 .06
3/4 4-3/4 1018133 1018160 2.32 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 3.44 .81 .25 .06
7/8 6-1/2 1018151 1018166 3.49 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 3.81 .97 .25 .06
1 8-1/2 1018179 1018188 5.00 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 4.53 1.06 .25 .06
1-1/8 9-1/2 1018197 1018204 6.97 1.81 1.25 4.25 1.13 2.91 2.69 5.16 7.47 5.13 1.25 .25 .06
1-1/4 12 1018213 1018222 9.75 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 5.50 1.38 .25 .06
1-3/8 13-1/2 1018231 1018240 13.25 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 6.13 1.50 .25 .13
1-1/2 17 1018259 1018268 17.25 2.38 1.63 5.75 1.54 3.88 3.63 6.88 10.00 6.50 1.62 .25 .13
1-3/4 25 1018277 1018286 29.46 2.88 2.00 7.00 1.64 5.00 4.19 8.86 12.34 7.75 2.25 .25 .13
2 35 1018295 1018302 45.75 3.25 2.25 7.75 2.08 5.75 4.81 9.97 13.68 8.75 2.40 .25 .13
360

G-215 / S-215 Round Pin
Cranes / Jibs
Overhead
Chain Shackles
G-215 Round pin chain shackles meet the performance
requirements of Federal Specification RR-C-271F Type IVB,
Hoists
the contractor.
■ Capacities 1/2 through 35 metric tons.

Services
every shackle.
■ Fatigue rated.
Engineered
Products
or other certification. Charges for proof testing and
of order.
■ Shackles are Quenched and Tempered and can meet
Slings
DNV impact requirements of 42 joules (31 ft-Ibs.) at
-20°C (-4°F).
Crosby quality.
Hardware
Working
Load
Limit
Products
Lifting
in. t* G-215 S-215 lbs. A B C D E F G K N C A
1/4 1/2 1018810 1018829 .10 .47 .31 .25 .25 .97 .62 .91 1.59 1.34 .06 .06
5/16 3/4 1018838 1018847 .18 .53 .38 .31 .31 1.15 .75 1.07 1.91 1.63 .06 .06
3/8 1 1018856 1018865 .25 .66 .44 .38 .38 1.42 .92 1.28 2.31 1.86 .13 .06
7/16 1-1/2 1018874 1018883 .40 .75 .50 .44 .44 1.63 1.06 1.48 2.67 2.13 .13 .06
1/2 2 1018892 1018909 .50 .81 .63 .50 .50 1.81 1.18 1.66 3.03 2.38 .13 .06
Rope
Wire
5/8 3-1/4 1018918 1018927 1.21 1.06 .75 .63 .63 2.32 1.50 2.04 3.76 2.91 .13 .06
3/4 4-3/4 1018936 1018945 2.00 1.25 .88 .81 .75 2.75 1.81 2.40 4.53 3.44 .25 .06
7/8 6-1/2 1018954 1018963 3.28 1.44 1.00 .97 .88 3.20 2.10 2.86 5.33 3.81 .25 .06
1 8-1/2 1018972 1018981 4.75 1.69 1.13 1.00 1.00 3.69 2.38 3.24 5.94 4.53 .25 .06
1-1/8 9-1/2 1018990 1019007 6.30 1.81 1.25 1.25 1.13 4.07 2.68 3.61 6.78 5.13 .25 .06
Cordage
1-1/4 12 1019016 1019025 9.00 2.03 1.38 1.38 1.25 4.53 3.00 3.97 7.50 5.50 .25 .13
1-3/8 13-1/2 1019034 1019043 12.00 2.25 1.50 1.50 1.38 5.01 3.31 4.43 8.28 6.13 .25 .13
1-1/2 17 1019052 1019061 16.15 2.38 1.63 1.62 1.50 5.38 3.62 4.87 9.05 6.50 .25 .13
1-3/4 25 1019070 1019089 29.96 2.88 2.00 2.12 1.75 6.38 4.19 5.82 10.97 7.75 .25 .13
2 35 1019098 1019105 43.25 3.25 2.25 2.36 2.10 7.25 5.00 6.82 12.74 8.75 .25 .13
Securement
Load
Contractors
Supply
Protection
Fall

361

G-209A Alloy Screw Pin
Shackles
G-209A Screw pin anchor shackles meet the performance
Grade B, Class 2, except for those provisions required of
the contractor.
■ Capacities 2 thru 21 metric tons. Meets performance

requirements of Grade 8 shackles.
■ Forged Alloy Steel – Quenched and Tempered,
with alloy pins.
every shackle.
■ Hot Dip Galvanized.
to designated standards, such as ABS, DNV, Lloyds or
other certification. Charges for proof testing and
of order.
■ Meets or exceeds all requirements of ASME B30.26
including identification, ductility, design factor,
proof load and temperature requirements. Importantly,
these shackles meet other critical performance
requirements including fatigue life, impact properties
and material traceability, not addressed by
ASME B30.26.
Working
Nominal G-209A Weight Dimensions Tolerance
Load
Size Stock Each (in.) +/-
Limit
No.
in. t* lbs. A B C D E F G H L M P C A
3/8 2 1017450 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.03 .38 .13 .06
7/16 2-2/3 1017472 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 .31 2.38 .44 .13 .06
1/2 3-1/2 1017494 .63 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 5 1017516 1.38 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
3/4 7 1017538 2.25 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 .50 3.97 .81 .25 .06
7/8 9-1/2 1017560 3.61 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 .50 4.50 .97 .25 .06
1 12-1/2 1017582 5.32 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 .56 5.07 1.06 .25 .06
1-1/8 15 1017604 7.25 1.81 1.25 4.25 1.16 2.91 2.69 5.16 7.47 .63 5.59 1.25 .25 .06
1-1/4 18 1017626 9.88 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 .69 6.16 1.38 .25 .06
1-3/8 21 1017648 13.25 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 .75 6.84 1.50 .25 .13
* Note: Maximum Proof Load is 2 times the Working Load Limit (metric tons) and 2.2 times the Working Load Limit (short tons).
Minimum Ultimate Strength is 4.5 times the Working Load Limit for metric tons, and 5 times the Working Load Limit for short tons.
362

Cranes / Jibs
Overhead
Wide Body Shackles
■ Capacities of 7, 12.5 and 18 metric tons.
■ Quenched and Tempered for maximum strength. G-2169 S-2169
■ Forged Alloy Steel.
Hoists
■ Available in galvanized and self colored finished.
■ Individually proof tested and magnetic particle
inspected. Crosby certification available at time
of order.
Services
■ Meets or exceeds all requirements of ASME B30.26
these shackles meet other critical performance
requirements, including fatigue life, impact properties
Engineered
Products
ASME B30.26.
Crosby quality.
Slings
Hardware
Products
Lifting
Working
Stock Weight Dimensions
Load
No. Each (in.)
Rope
Wire
Limit
B D
t* G-2169 S-2169 lbs. +/- C +/- E G H J K L M P R
.25 .02
7 1021665 1021664 3.5 1.25 .69 .88 1.82 1.25 3.56 1.60 1.25 .50 3.97 4.10 5.87
Cordage
12.5 1021673 1021682 8.8 1.69 .92 1.13 2.38 1.37 4.63 2.13 1.63 .56 5.13 5.51 7.63
18 1021691 1021669 13 2.03 1.16 1.38 2.69 1.50 5.81 2.50 2.00 .69 6.25 6.76 9.38
* Note: Ultimate Load is 5 times the Working Load Limit. Forged Alloy Steel. Proof Load is 2 times the Working Load Limit.
Securement
Load
Contractors
Supply
Protection
Fall

363

G-2130 / S-2130 Bolt Type
Anchor Shackles
G-2130 Bolt type anchor shackles with thin head bolt - nut with
cotter pin. Meets the performance requirements of Federal Specification
RR-C-271F Type IVA, Grade A, Class 3, except for those provisions
required of the contractor.

■ Working Load Limit and grade “6” permanently shown on
every shackle.
■ Forged – Quenched and Tempered, with alloy pins.
■ Hot Dip galvanized or Self Colored. (85, 120, and 150 metric
ton shackles are all hot dip galvanized bows and the bolts
are Dimetcoted® and painted red)
■ Fatigue rated (1/3t - 55t).
■ Meets or exceeds all requirements of ASME B30.26.
■ Shackles 85 metric tons and larger are individually
proof tested to 2.0 times the working load limit.
■ Shackles 120 metric tons and larger are proof tested, Magnetic
Particle Inspected and provided with Serialized Pin and Bow.
■ Type Approval and certification in accordance with ABS 2006 Steel
Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes. (31 ft.-lbs.) min. ave. at -20°C (-4°F). The tests are conducted by
■ 3.1 Certification as standard available for charpy and statistical Crosby and 3.1 test certification is available upon request.
proof test only up to 25 tons to DNV2.7-1 and EN13889. ■ All other 2130 and all 2150 shackles can meet charpy requirements
■ Crosby 2t through 25t G2130 anchor shackles are type approved to of 42 joules (31 ft.-lbs) avg. at -20°C (-4°F) upon special request.
DNV Certification Notes 2.7-1- Offshore Containers. These Crosby ■ Look for the Red Pin®…the mark of genuine Crosby quality.
shackles are statistical proof and impact tested to 42 joules
Working
Load
Limit
in. t* G-2130 S-2130 lbs. A B C D E F H L N C A
3/16 1/3 ‡ 1019464 – .06 .38 .25 .88 .19 .60 .56 1.47 .98 .19 .06 .06
1/4 1/2 1019466 – .11 .47 .31 1.13 .25 .78 .61 1.84 1.28 .25 .06 .06
5/16 3/4 1019468 – .22 .53 .38 1.22 .31 .84 .75 2.09 1.47 .31 .06 .06
3/8 1 1019470 – .33 .66 .44 1.44 .38 1.03 .91 2.49 1.78 .38 .13 .06
7/16 1-1/2 1019471 – .49 .75 .50 1.69 .44 1.16 1.06 2.91 2.03 .44 .13 .06
1/2 2 1019472 1019481 .79 .81 .64 1.88 .50 1.31 1.19 3.28 2.31 .50 .13 .06
5/8 3-1/4 1019490 1019506 1.68 1.06 .77 2.38 .63 1.69 1.50 4.19 2.94 .69 .13 .06
3/4 4-3/4 1019515 1019524 2.72 1.25 .89 2.81 .75 2.00 1.81 4.97 3.50 .81 .25 .06
7/8 6-1/2 1019533 1019542 3.95 1.44 1.02 3.31 .88 2.28 2.09 5.83 4.03 .97 .25 .06
1 8-1/2 1019551 1019560 5.66 1.69 1.15 3.75 1.00 2.69 2.38 6.56 4.69 1.06 .25 .06
1-1/8 9-1/2 1019579 1019588 8.27 1.81 1.25 4.25 1.33 2.91 2.69 7.47 5.16 1.25 .25 .06
1-1/4 12 1019597 1019604 11.71 2.03 1.40 4.69 1.29 3.25 3.00 8.25 5.75 1.38 .25 .06
1-3/8 13-1/2 1019613 1019622 15.83 2.25 1.53 5.25 1.42 3.63 3.31 9.16 6.38 1.50 .25 .13
1-1/2 17 1019631 1019640 19 2.38 1.66 5.75 1.53 3.88 3.63 10.00 6.88 1.62 .25 .13
1-3/4 25 1019659 1019668 33.91 2.88 2.04 7.00 1.84 5.00 4.19 12.34 8.80 2.25 .25 .13
2 35 1019677 1019686 52.25 3.25 2.30 7.75 2.08 5.75 4.81 13.68 10.15 2.40 .25 .13
2-1/2 55 1019695 1019702 98.25 4.13 2.80 10.50 2.71 7.25 5.69 17.90 12.75 3.13 .25 .25
3 † 85 1019711 – 154 5.00 3.30 13.00 3.12 7.88 6.50 21.50 14.62 3.62 .25 .25
3-1/2 † 120 ‡ 1019739 – 265 5.25 3.75 14.63 3.62 9.00 8.00 24.88 17.02 4.38 .25 .25
4 † 150 ‡ 1019757 – 338 5.50 4.26 14.50 4.00 10.00 9.00 25.68 18.00 4.56 .25 .25
† Individually Proof Tested with certification.
‡ Furnished in Anchor style only and furnished with Round Head Bolts with welded handles.
364

G-2150 / S-2150 Bolt Type
Cranes / Jibs
Overhead
Chain Shackles
G-2130 Bolt type anchor shackles with thin head bolt - nut with
cotter pin. Meets the performance requirements of Federal Specification
RR-C-271F Type IVA, Grade A, Class 3, except for those provisions
Hoists

■ Working Load Limit and grade “6” permanently shown on
every shackle.
Services
■ Forged – Quenched and Tempered, with alloy pins.
■ Hot Dip galvanized or Self Colored. (85, 120 and 150 metric
ton shackles are all hot dip galvanized bows and the bolts
are Dimetcoted® and painted red)
■ Fatigue rated (1/3t - 55t).
Engineered
Products
■ Meets or exceeds all requirements of ASME B30.26.
■ Shackles 85 metric tons and larger are individually
proof tested to 2.0 times the working load limit.
■ Shackles 120 metric tons and larger are proof tested, Magnetic
Particle Inspected and provided with Serialized Pin and Bow.
Slings
■ Type Approval and certification in accordance with ABS 2006 Steel
Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes. (31 ft.-lbs.) min. ave. at -20°C (-4°F). The tests are conducted by
■ 3.1 Certification as standard available for charpy and statistical Crosby and 3.1 test certification is available upon request.
proof test only up to 25 tons to DNV2.7-1 and EN13889. ■ All other 2130 and all 2150 shackles can meet charpy requirements
■ Crosby 2t through 25t G2130 anchor shackles are type approved to of 42 joules (31 ft.-lbs) avg. at -20°C (-4°F) upon special request.
Hardware
DNV Certification Notes 2.7-1- Offshore Containers. These Crosby ■ Look for the Red Pin®…the mark of genuine Crosby quality.
shackles are statistical proof and impact tested to 42 joules
Working
Products
Lifting
Load
Limit
in. t* G-2150 S-2150 lbs. A B D F G K M P R G A
1/4 1/2 1019768 – .13 .47 .31 .25 .62 .91 1.59 .97 1.56 .25 .06 .06
5/16 3/4 1019770 – .23 .53 .38 .31 .75 1.07 1.91 1.15 1.82 .31 .06 .06
3/8 1 1019772 – .33 .66 .44 .38 .92 1.28 2.31 1.42 2.17 .38 .13 .06
Rope
Wire
7/16 1-1/2 1019774 – .49 .75 .50 .44 1.06 1.48 2.67 1.63 2.51 .44 .13 .06
1/2 2 1019775 1019784 .75 .81 .64 .50 1.18 1.66 3.03 1.81 2.80 .50 .13 .06
5/8 3-1/4 1019793 1019800 1.47 1.06 .77 .63 1.50 2.04 3.76 2.32 3.56 .63 .13 .06
3/4 4-3/4 1019819 1019828 2.52 1.25 .89 .75 1.81 2.40 4.53 2.75 4.15 .81 .25 .06
7/8 6-1/2 1019837 1019846 3.85 1.44 1.02 .88 2.10 2.86 5.33 3.20 4.8 .97 .25 .06
Cordage
1 8-1/2 1019855 1019864 5.55 1.69 1.15 1.00 2.38 3.24 5.94 3.69 5.39 1.00 .25 .06
1-1/8 9-1/2 1019873 1019882 7.60 1.81 1.25 1.13 2.68 3.61 6.78 4.07 5.90 1.25 .25 .06
1-1/4 12 1019891 1019908 10.81 2.03 1.40 1.25 3.00 3.97 7.50 4.53 6.69 1.38 .25 .06
1-3/8 13-1/2 1019917 1019926 13.75 2.25 1.53 1.38 3.31 4.43 8.28 5.01 7.21 1.50 .25 .13
1-1/2 17 1019935 1019944 18.50 2.38 1.66 1.50 3.62 4.87 9.05 5.38 7.73 1.62 .25 .13
1-3/4 25 1019953 1019962 31.40 2.88 2.04 1.75 4.19 5.82 10.97 6.38 9.33 2.12 .25 .13
Securement
2 35 1019971 1019980 46.75 3.25 2.30 2.10 5.00 6.82 12.74 7.25 10.41 2.36 .25 .13
Load
2-1/2 55 1019999 1020004 85.00 4.13 2.80 2.63 5.68 8.07 14.85 9.38 13.58 2.63 .25 .25
3 † 85 1020013 – 124.25 5.00 3.25 3.00 6.50 8.56 16.87 11.00 15.13 3.50 .25 .25
3 † 85 1019711 – 154 5.00 3.30 13.00 3.12 7.88 6.50 21.50 14.62 3.62 .25 .25
Contractors
† Individually Proof Tested with certification.

Supply
‡ Furnished in Anchor style only and furnished with Round Head Bolts with welded handles.
Protection
Fall

365

G-2140 Alloy Bolt Type
Shackles
G-2140 meets the performance requirements of Federal Specification
RR-C-271F, Type IVA, Grade B, Class 3, except for those provisions
■ Quenched and Tempered.

■ Alloy bows, Alloy bolts.
■ Forged Alloy Steel 30 thru 175 metric tons and Cast Alloy
Steel 200 thru 400 metric tons. Meets performance requirements
of Grade 8 shackles.
■ Working Load Limit is permanently shown on every shackle.
■ 30, 40, 55 and 85 metric ton shackle bows are available
galvanized or self colored with pins that are galvanized and
painted red. 120, 150, 175 metric ton shackle bows are hot-dip
galvanized; pins are Dimetcoted® and painted red.
200, 250, 300 and 400 metric ton shackle bows are
Dimetcoted®; pins are Dimetcoted® and painted red.
■ All sizes are RFID EQUIPPED.
■ Shackles are Quenched and Tempered and can meet DNV impact
requirements of 42 joules (31 ft.-lbs.) at -20°C (-4°F). ■ Meets or exceeds all requirements of ASME B30.26 including
■ All sizes are individually proof tested to 2.0 times the identification, ductility, design factor, proof load and temperature
Working Load Limit. requirements. Importantly, these shackles meet other critical
■ Shackles 200 metric tons and larger are provided as follows. performance requirements including fatigue life, impact properties
■ Serialized Pin and Bow and material traceability, not addressed by ASME B30.26.
■ Material Certification (Chemical) ■ Type Approval and certification in accordance with ABS 2006 Steel
■ Magnetic Particle Inspected. Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.
■ Certification must be requested at time of order. ■ Look for the Red Pin®…the mark of genuine Crosby quality.
Working Toler-
Nominal Stock Weight Dimensions
Load ance
Size No. Each (in.)
Limit +/-
in. t* G-2140 S-2140 lbs. A B C D E F G H J K L A E
1-1/2 30 1021110 1021129 18.8 2.38 3.62 1.62 1.63 5.75 1.39 6.88 7.73 10.00 3.88 1.53 .13 .25
1-3/4 40 1021138 1021147 33.8 2.88 4.19 2.25 2.00 7.00 1.75 8.81 9.33 12.34 5.00 1.84 .13 .25
2 55 1021156 1021165 49.9 3.25 4.81 2.40 2.25 7.75 2.00 10.16 10.41 13.68 5.75 2.08 .13 .25
2-1/2 85 1021174 1021183 103 4.12 5.81 3.12 2.75 10.50 2.62 12.75 13.58 17.90 7.25 2.71 .25 .25
3 120 1021192 – 162 5.00 6.50 3.63 3.25 13.00 3.00 14.62 15.13 21.50 7.88 3.12 .25 .25
3-1/2 † 150 1021218 – 268 5.25 8.00 4.38 3.75 14.63 3.75 17.02 17.62 24.88 9.00 3.62 .25 .25
4 † 175 1021236 – 332 5.50 9.00 4.56 4.25 14.50 4.00 18.00 20.37 25.68 10.00 4.00 .25 .25
4-3/4 ** † 200 1021414 – 455 7.25 10.50 6.00 4.75 15.63 3.75 21.00 21.21 29.25 11.00 4.50 .25 .25
5 ** † 250 1021432 – 650 8.50 12.00 6.50 5.00 20.00 3.88 24.50 22.68 35.00 13.00 4.50 .25 .25
6 † 300 1021450 – 780 8.38 12.00 6.75 6.00 19.50 4.75 25.00 25.06 35.25 13.00 5.00 .25 .25
7 ** † 400 1021478 – 1200 8.25 14.00 7.25 7.00 22.50 6.50 26.00 28.68 40.25 13.00 6.00 .25 .25
* Note: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Load is 4 times the Working Load Limit on
200 thru 400 metric tons. For sizes 30 thru 175 metric tons, Minimum Ultimate Load is 5.4 times the Working Load Limit.
** Cast Alloy Steel.
† Furnished with Round Head Bolts with an eyebolt for handling
366

G-2160 / S-2160
Cranes / Jibs
Overhead
Wide Body Shackles
■ All sizes Quenched and Tempered for maximum strength.
■ Forged alloy steel from 7 through 300 metric tons.
■ Cast alloy steel from 400 through 1550 metric tons.
Hoists
■ Sizes 300 metric tons and smaller are proof tested to 2 times
the Working Load Limit.
■ Sizes 400 metric tons and larger are tested to 1.33 times
Working Load Limit.
■ All ratings are in metric tons, embossed on side of bow.
Services
■ G-2160, (7-55t), are Hot Dip Galvanized and pins are painted red.
■ G-2160, (75t and larger), bows are furnished Dimetcoted,
and pins are Dimetcoted, then painted red.
■ S-2160 bows and pins are painted red. Patented
■ Shackles, 30t and larger, are RFID EQUIPPED.
■ Can be used to connect HIGH STRENGTH Synthetic Web Slings,
Engineered
Products
HIGH STRENGTH Synthetic Round Slings or Wire Rope Slings.
■ Increase in shackle bow radius provides minimum 58% gain in sling
bearing surface and eliminates need for a thimble.
■ Increases usable sling strength minimum of 15% and greatly
improves life of wire rope slings.
■ Pin is non-rotating, with weld-on handles for easier use
Slings
(75t and larger). ■ Shackles 18t and larger have DNV Type Approval to Rules for
■ Approved for use at -40°C (-40°F) to 204°C (400°F). Certification of Lifting Appliances, and are produced in accordance
■ Bow and bolt are Certified to meet charpy impact testing of with DNV MSA requirements. Databook is provided that includes
42 joules (31 ft.-Ibs.) min. ave. at -20°C (-4°F). required documents.
■ All 2160 shackles are individually proof tested and magnetic ■ Serialization / Identification
Hardware
particle inspected. Crosby certification available at time of order. ■ Material Testing (Physical / Chemical / Charpy)
■ Shackles requiring ABS, Lloyds and other certifications are ■ Proof Testing
available upon special request and must be specified at ■ Look for the Red Pin®…the mark of genuine Crosby quality.
time of order.
Working
Products
Lifting
Load Effective
No. Each (in.)
Limit Body
B +/- D +/- Diameter
t* G-2160 S-2160 lbs. A C E G H J K P R
.25 .02
7 1021256 1021548 4.0 4.14 1.25 .69 .88 1.82 1.25 3.56 1.60 1.25 4.10 5.87 2.1
12.5 1021265 1021557 8.8 5.38 1.69 .92 1.13 2.38 1.37 4.63 2.13 1.63 5.51 7.63 2.4
Rope
Wire
18 1021274 1021566 14.9 6.69 2.03 1.16 1.38 2.69 1.50 5.81 2.50 2.00 6.76 9.38 2.8
30 1021283 1021575 26.5 7.69 2.37 1.38 1.63 3.50 1.75 6.94 3.13 2.50 8.50 11.38 4.1
40 1021285 1021584 – 9.28 2.88 1.69 2.00 4.00 2.31 8.06 3.75 3.00 10.62 13.62 3.6
55 1021287 1021593 68 10.36 3.25 2.00 2.25 4.63 2.63 9.36 5.00 3.50 12.26 15.63 4.3
† 75 1021290 – 99 14.37 4.13 2.12 2.75 5.00 2.50 11.53 4.75 3.64 12.28 18.41 5.9
Cordage
† 125 1021307 – – 16.51 5.12 2.56 3.15 5.71 3.15 14.36 5.91 4.33 14.96 22.65 6.8
† 200 1021316 – 370 20.67 5.91 3.35 4.12 7.28 4.33 18.90 8.63 5.41 19.49 29.82 8.9
† 300 1021325 – 847 24.20 7.38 4.00 5.25 9.25 5.38 23.63 10.38 6.31 23.38 37.26 11.8
400 1021334 – 1,130 30.27 8.66 5.16 6.30 11.81 6.30 22.64 12.60 7.28 27.17 38.76 14.3
500 1021343 – 1,440 33.35 9.84 5.73 7.09 13.39 6.69 24.81 13.39 8.86 31.10 42.72 14.8
Securement
600 1021352 – 1,995 36.02 10.83 6.25 7.87 15.50 7.28 27.56 14.57 9.74 34.06 47.24 20.3
700 1021361 – 2,415 38.91 11.81 6.59 8.46 14.80 7.87 28.94 15.75 10.63 37.01 50.18 16.6
Load
800 1021254 – 2,880 41.66 12.80 7.30 9.06 16.54 8.27 29.53 16.54 10.92 38.39 52.09 18.0
900 1021389 – 3,628 43.73 13.78 7.78 9.84 16.63 8.66 29.82 17.32 11.52 40.35 54.04 22.4
1,000 1021370 – 4,155 45.98 14.96 8.33 10.63 17.72 9.06 29.92 18.11 12.11 42.32 55.31 19.3
1,250 1021272 – 5,320 49.86 16.93 9.15 11.81 21.00 10.43 36.61 20.87 12.70 46.26 65.35 24.4
1,550 1021281 – 8,302 54.89 18.31 10.58 12.60 23.82 15.92 42.32 22.82 13.29 49.41 73.43 27.3
Contractors
Supply
* 7t-300t Proof Load is 2 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
400t-1550t Proof Load is 1.33 times the Working Load Limit. Ultimate Load is 4.5 times the Working Load Limit.
† Available in Forged and Cast Alloy Steel.
Protection
Fall

367

S-209T
Theatrical Shackles
■ Sizes: 3/8" through 3/4"
■ Capacities 1 through 4-3/4 metric tons.
■ Working Load Limit permanently shown on every shackle.
■ Flat black baked on power coat finish.
■ Fatigue Rated.
■ Industry leading 6 to 1 design factor.
■ Screw pin anchor shackles meet the performance requirement
of Federal Specification RR-C-271F Type A, Grade A, Class 2,
except for those provisions required of the contractor.
■ Meets the performance requirements of EN 13889:2003.
■ Meets or exceeds all requirements of ASME B30.26, including
identification, ductility, design factor, proof load and
temperature requirements. Importantly, these shackles
meet other critical performance requirements,
including fatigue life, impact properties and material
traceability, not addressed by ASME B30.26.
Working
Load
Limit
Stock
in. t lbs. A B C D E F G H L M P C A
No.
3/8 1 1018706 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.02 .38 .13 .06
7/16 1-1/2 1018724 .38 .75 .50 1.69 .4 1.16 1.06 2.03 2.91 .31 2.37 .44 .13 .06
1/2 2 1018742 .72 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 3-1/4 1018760 1.37 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
368

Midland WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Anchor Shackles
■ All shackles meet or exceed Federal Specification
RRC-271D
■ Working Load Limit and traceability codes shown
Hoists
as permanent marking on body and pin
■ Available in painted, galvanized and self-colored
finishes (Dacromate coating upon special request only)
■ All shackles have alloy quenched and tempered pins Screw Pin
Services
■ Shackles exhibit extreme deformation before failure *
■ Special testing and certification including magnetic
particle, proof load and fatigue test available
upon request at time of order
■ Special products engineering available to fit your
Engineered
Products
special lifting, tie down and pulling needs
■ Design factor 5:1
* WARNING: Working load limit is not to be exceeded. Round Pin
Slings
Hardware
Bolt & Nut
Products
Lifting
Working Product Code Dimensions (in.)
Size Weight
Load Limit Screw Round Bolt &
(in.) P E W R L B min (lbs.)
(ton) * Pin Pin Nut
3/8 2 M648A – M848A 0.438 0.531 0.656 1.125 1.437 0.937 0.30
Rope
Wire
7/16 2.6 M649A M349A M849A 0.500 0.593 0.750 1.250 1.689 1.062 0.50
1/2 3.3 M650A M350A M850A 0.625 0.718 0.813 1.375 1.875 1.187 0.75
5/8 5 M651A M351A M851A 0.750 0.843 1.063 1.875 2.375 1.500 1.30
3/4 7 M652A M352A M852A 0.875 0.968 1.250 2.125 2.813 1.750 2.30
7/8 9.5 M653A M353A M853A 1.000 1.109 1.438 2.375 3.312 2.000 3.50
Cordage
1 12.5 M654A M354A M854A 1.125 1.234 1.688 2.625 3.750 2.312 5.00
1-1/8 15 M655A M355A M855A 1.250 1.375 1.812 2.875 4.250 2.625 7.00
1-1/4 18 M656A M356A M856A 1.375 1.531 2.031 3.250 4.688 2.875 9.50
1-3/8 21 M666A M366A M866A 1.500 1.656 2.250 3.500 5.250 3.250 12.50
1-1/2 25 M657A M357A – 1.625 1.781 2.375 3.750 5.750 3.375 17.20
1-1/2 30 – – M857A 1.625 1.781 2.375 3.750 5.750 3.375 17.20
Securement
1-5/8 29 M685A M385A – 1.750 1.906 2.625 4.125 6.250 4.000 23.50
Load
1-5/8 35 – – M885A 1.750 1.906 2.625 4.125 6.250 4.000 23.50

1-3/4 34 M677A M377A v 2.000 2.156 2.875 4.500 7.000 4.500 27.70
1-3/4 40 – – M877A 2.000 2.156 2.875 4.500 7.000 4.500 27.70
2 43 M658A M358A – 2.250 2.406 3.250 5.250 7.750 5.250 39.00
2 50 – – M858A 2.250 2.406 3.250 5.250 7.750 5.250 39.00
Contractors
2-1/2 85 – – MC860AG 2.750 2.906 4.125 6.250 10.500 6.750 90.50

Supply
3 120 – – MC862AG 3.250 3.406 5.000 6.750 13.000 7.375 137.00
* WARNING: Working load limit is not to be exceeded.

Protection
Fall

369

Midland WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Chain Shackles
■ All shackles meet or exceed Federal Specification
RRC-271D
■ Working Load Limit and traceability codes shown
as permanent marking on body and pin
■ Available in painted, galvanized and self-colored
finishes (Dacromate coating upon special request only)
■ All shackles have alloy quenched and tempered pins Screw Pin
■ Shackles exhibit extreme deformation before failure *
■ Special testing and certification including magnetic
particle, proof load and fatigue test available
upon request at time of order
■ Special products engineering available to fit your
special lifting, tie down and pulling needs
■ Design factor 5:1
* WARNING: Working load limit is not to be exceeded. Round Pin
Bolt & Nut
Working Product Code Dimensions (in.)

Size Weight
Load Limit Screw Round Bolt &
(in.) P E W R L (lbs.)
(ton) * Pin Pin Nut
3/8 2 M748A – M948A .438 .531 .656 1.125 1.437 .25
7/16 2.6 M749A – M949A .5 .593 .75 1.25 1.689 .40
1/2 3.3 M750A M550A M950A .625 .718 .813 1.375 1.875 .75
5/8 5 M751A M551A M951A .75 .843 1.063 1.875 2.375 1.3
3/4 7 M752A M552A M952A .875 .968 1.25 2.125 2.813 2.3
7/8 9.5 M753A M553A M953A 1 1.109 1.438 2.375 3.312 3.5
1 12.5 M754A M554A M954A 1.125 1.234 1.688 2.625 3.75 5
1-1/8 15 M755A M555A M955A 1.25 1.375 1.812 2.875 4.25 7
1-1/4 18 M756A M556A M956A 1.375 1.531 2.031 3.25 4.688 9.5
1-3/8 21 M766A M566A M966A 1.5 1.656 2.25 3.5 5.25 12.5
1-1/2 30 M757A M557A M957A 1.625 1.781 2.375 3.75 5.75 17.2
1-5/8 35 M785A M585A M985A 1.75 1.906 2.625 4.125 6.25 23.5
1-3/4 40 M777A M577A M977A 2 2.156 2.875 4.5 7 27.7
2 50 M758A M558A M958A 2.25 2.406 3.25 5.25 7.75 39
* WARNING: Working load limit is not to be exceeded.
370

Alloy No. 59A WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Sheet Pile Shackles
The No. 59A shackles were specifically designed
for pulling sheet piling. They are equipped with an easy
opening pin which will not detach and become lost.
Hoists
■ No tools are required.
■ Max opening with pin in open (unlocked) position.
■ Design factor is 5 to1.
Services
■ Replacement pins must be replaced or repaired by
Skookum in Hubbard, OR.
■ Made in the U.S.A.
Engineered
Products
Opening WLL
Size A B C D E F G H Weight
2 (tons)
1 1.75 4.25 2.25 1.00 1.12 7 ± .25 0.62 2.37 5.00 10 8
Slings
1-1/8 1.87 4.50 2.50 1.00 1.25 8 ± .50 0.75 3.00 5.00 13 10
1-1/4 2.00 5.25 2.75 1.25 1.37 9 ± .50 0.87 3.00 5.00 18 12
1-1/2 2.12 6.25 3.00 1.50 1.62 10 ± .50 1.12 3.50 6.00 29 17
1-3/4 2.50 7.00 3.50 1.75 2.00 11 ± .50 1.25 4.00 7.00 45 24
Hardware
2 3.00 8.00 4.00 2.00 2.25 12 ± .75 1.37 4.50 8.00 63 30
All dimensions in inches.
No. 159A Sheet Pile
Products
Lifting
Shackle Ground Release
■ 12 ton working load limit at 4:1 design factor.
■ Skookum Part Number 615912
Rope
Wire
■ Equipped with Skookum 1" #320 bolt type
anchor shackle
■ Built with high strength steel.
■ 12" lg. stainless steel release cable with thimble.
Cordage
(supplied but not shown)
Securement
Load
Contractors
Supply
Protection
Fall

371

Alloy Towing WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Shackles
■ Hot galvanized, forged, heat-treated, all alloy steel
■ Extra wide opening for hawser thimbles
■ Permanently marked with size and Working Load Limit.
Replacement Bolts
■ Intended for use with KULKONI Towing Shackles only.
■ Complete with bolt, nut and cotter pin. Alloy steel,
hot galvanized.
Alloy Towing Shackles Replacement Bolts

Working Bolt Mouth Approx. Fits Approx.
Size Dimension (in.) Diameter Shackle Weight
Load Dia. Opening Weight
A (in.) Size Each
Limit B D Each
(in.) C E F (in.) (lbs.)
(tons) (in.) (in.) (lbs.)
1-1/2 22 1-7/8 4.19 27.5 8.50 3.75 6.25 1-7/8 1-1/2 10.7
1-3/4 30 2 5.00 40 9.75 4.38 6.88 2 1-3/4 13.6
2 40 2-1/4 5.75 56 10.75 5.00 8.13 2-1/4 2 20.0
2-1/2 55 2-3/4 6.50 106 12.38 6.00 8.38 2-3/4 2-1/2 34.7
3 80 3-1/4 7.25 157 13.00 6.75 10.00 3-1/4 3 52.6
* The YELLOW shackle bolt is the Federally Registered Trademark of Kulkoni, Inc.
** Some sizes may have single nut, double cotter pin.
Galvanized Bolt Type

Chain Shackles
■ Meets the performance requirements of
Federal Specification RR-C-271D, Type IV B,
Class 3, Grade A, Amendment 1.
■ Hot galvanized, forged carbon steel, heat treated,
with alloy bolts,
■ Permanently marked with size and Working Load Limit.
Size Working Bolt Length Width Between Eyes D Approx.

A Load Limit Diameter B Inside C E Weight Each
(in.) (tons) (in.) (in.) Nominal Tolerance (lbs.)
1/2 2 5/8 1-5/8 13/16 ± 1/16 1-3/8 .91
5/8 3-1/4 3/4 2 1-1/16 ± 1/16 1-7/8 1.72
3/4 4-3/4 7/8 2.3/8 1-1/4 ± 1/16 2-1/8 2.70
7/8 6-1/2 1 2-13/16 1-7/16 ± 1/16 2-3/8 3.94
1 8-1/2 1-1/8 3.3/16 1-11/16 ± 1/8 2-5/8 5.75
1-1/8 9-1/2 1-1/4 3-9/16 1-13/16 ± 1/8 2-7/8 8
1-1/4 12 1-3/8 3-15/16 2-1/32 ± 1/8 3-1/4 10.5
1-3/8 13-1/2 1-1/2 4-7/16 2-1/4 ± 1/8 3-1/2 13.1
1-1/2 17 1-5/8 4-7/8 2-3/8 ± 1/8 3-3/4 18.3
1-3/4 25 2 5-3/4 2-7/8 ± 3/16 4-1/2 29.3
2 35 2-1/4 6-3/4 3-1/4 ± 3/16 5-1/4 44.3
2-1/2 55 2-3/4 8 4-1/8 ± 1/4 6-1/4 94
3 85 3-1/4 9 5 ± 1/4 6-3/4 125
3-1/2 120 3-3/4 10-1/2 5-1/2 ± 1/4 8-1/2 250
U.S. Registered Trademark No. 2,011,393

* The YELLOW shackle bolt is the Federally Registered Trademark of Kulkoni, Inc.
** Minimum Width Between Eyes as defined by Federal Specification RR-C-271D, Amendment 1.
372

Stainless Steel Shackles— WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Type 304
A Dimensions
WLL Weight
Item Size (in.)
Hoists
(in.) B C D lbs. lbs.
S0116-FS05 3/16 .26 .41 .83 650 .05
S0116-FS07 1/4 .31 .47 1.11 1,000 .10
S0116-FS08 5/16 .38 .53 1.20 1,300 .17
Services
S0116-FS10 3/8 .44 .66 1.41 1,500 .30
S0116-FS12 7/16 .50 .72 1.77 2,000 .50
S0116-FS13 1/2 .63 .82 1.83 3,000 .71
S0116-FS16 5/8 .75 1.02 2.41 4,000 1.39
S0116-FS20 3/4 .88 1.25 2.84 6,000 2.31
Engineered
Products
S0116-FS22 7/8 1 1.48 3.30 8,000 3.64
S0116-FS25 1 1.13 1.70 3.80 10,000 5.18
S0116-FS32 1-1/4 1.38 2.03 4.69 14,000 9.88
Screw Pin
Grade: 316NM Stainless Steel

I/A/W Fed Spec RR-C-271D, Type IVA, Class 3, Except 316
Slings
Stainless, Drop Forged & Load Rated

This anchor shackle is made from grade 316 NM stainless steel
and features an oversize screw pin. Stainless steel anchor shackles
Hardware
are ideal for salt water applications. The anchor shackle is primarily
used to connect the anchor to the chain.
Bolt Type
Products
Lifting
Design-A-Shackle
Custom Shackle F
Rope
Wire
B
Capacity ________________________________________
Style ___________________________________________
C
A. ____________________________________________ Cordage
B. ____________________________________________ D
C. ____________________________________________
Securement
A E A
D. ____________________________________________
Load
E. ____________________________________________ Chain Anchor

F. ____________________________________________ Style Style
Contractors
Supply
Contact us with your dimensions, using the

drawing on the right side of this page.
Protection
Fall

373

Swivel Hoist Ring
U.S. Patent 5,352,056
■ Available in UNC and Metric thread sizes. Color coded to distinguish between UNC (Red)
■ UNC threads available in sizes from 800 pounds to and Metric (Silver) thread types.
100,000 pounds Working Load Limit, with a design
factor of 5 to 1.
■ Metric threads available in sizes from 400 kg to HR-125
16,900 kg and dual rated in both a 4 to 1 and
5 to 1 design factor.
■ All Components are Alloy Steel - Quenched
and Tempered.
■ Rated at 100% at 90° angle.
■ 100% individually proof tested to 2-1/2 times the
Working Load Limit with certification and Statistically
Magnetic Particle inspected. (Can be furnished 100%
Magnetic Particle inspected when requested at
time of order.)
■ Each product has a Product Identification Code (PIC)
for material traceability, along with a Working Load Limit
and the name Crosby or “CG” stamped into it.
■ Meets or exceeds all the requirements of ASME B30.26,
including identification, ductility, design factor, proof
load and temperature requirements. Importantly,
these hoist rings meet other critical performance
ASME B30.26.
■ 360° swivel and 180° pivot action. HR-125 M
■ Fatigue rated to 20,000 cycles at 1-1/2 times the
Working Load Limit.
■ Individually packaged along with proper application
instructions and warning information.
■ Bolt is secured with E-clip, threads are grooved. This
method allows for easy disassembly and assembly
of hoist ring for thorough examination of all components.
Replacement kits are available.
■ Bolts are individually Proof Tested.
■ Multiple Bolt length available to meet specific
application requirements.
■ Zinc Plated (Yellow Chromate) finish for increased
corrosion protection thru 30,000 pounds size.
■ Also available in Stainless Steel
374

UNC Swivel Hoist Rings WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
■ Top washer has the following features:
- The Working Load Limit and Recommended Torque
value are permanently stamped into each washer.
- Washer is color coded for easy identification:
Hoists
Red - UNC thread.
■ Individually Proof Tested to 2-1/2 times HR-125
Working Load Limit.
■ Bolt specification is a Grade 8 Alloy socket head cap
screw to ASTM A 574. All threads listed are UNC.
Services
■ BOLT SIZE IDENTIFICATION: The size of the bolt
will be stated as in the drawing below. Illustration shows
meaning of each dimension given.
■ Frame 2 and larger are RFID EQUIPPED.
■ Also available in Stainless Steel.
Engineered
Products
Slings
HR-125 UNC Threads
Hardware
Dimensions (in.)
Working Effective
Frame HR-125 Torque Weight
Load Thread
Size Stock in Bolt Size Radius Dia. Each
Limit Projection C D G H
No. No. Ft. Lbs. A‡ E F (lbs.)
Products
(lbs.) * Length
Lifting
B
1† 1016887 800 7 5/16 - 18 x 1.50 .58 2.72 .97 .46 .34 1.87 1.12 .37
1† 1016898 1,000 12 3/8 - 16 x 1.50 .58 2.72 .97 .46 .34 1.87 1.05 .39
2 1016909 2,500 28 1/2 - 13 x 2.00 .70 4.85 1.96 .87 .69 3.35 2.29 2.33
2† 1016912 2,500 28 1/2 - 13 x 2.50 1.20 4.85 1.96 .87 .69 3.35 2.29 2.36
2 1016920 4,000 60 5/8 - 11 x 2.00 .70 4.85 1.96 .87 .69 3.35 2.16 2.41
Rope
Wire
2† 1016924 4,000 60 5/8 - 11 x 2.75 1.45 4.85 1.96 .87 .69 3.35 2.16 2.47
2 1016931 5,000 100 3/4 - 10 x 2.25 .95 4.85 1.96 .87 .69 3.35 2.04 2.52
2† 1016935 5,000 100 3/4 - 10 x 2.75 1.45 4.85 1.96 .87 .69 3.35 2.04 2.59
3 1016942 7,000 ** 100 3/4 - 10 x 2.75 .89 6.57 2.96 1.36 .94 4.87 2.97 6.72
3† 1016946 7,000 ** 100 3/4 - 10 x 3.50 1.64 5.57 2.96 1.36 .94 4.87 2.97 6.81
Cordage
3 1016953 8,000 160 7/8 - 9 x 2.75 .89 6.57 2.96 1.36 .94 4.87 2.84 6.84
3† 1016957 8,000 160 7/8 - 9 x 3.50 1.64 6.57 2.96 1.36 .94 4.87 2.84 6.96
3 1016964 10,000 230 1 - 8 x 3.00 1.14 6.57 2.96 1.36 .94 4.87 2.72 7.09
3† 1016969 10,000 230 1 - 8 x 4.00 2.14 6.57 2.96 1.36 .94 4.87 2.72 7.31
4 1016975 15,000 470 1-1/4 - 7 x 4.50 2.21 8.72 3.71 1.75 1.19 6.18 3.93 14.51
Securement
5 1016986 24,000 800 1-1/2 - 6 x 6.75 2.73 12.55 4.71 2.39 1.75 8.48 5.52 37.73
5 1016997 30,000 1,100 2 - 4-1/2 x 6.75 2.73 12.55 4.71 2.39 1.75 8.48 5.02 40.69
Load
6 1017001 50,000 2,100 2-1/2 - 4 x 8.00 4.00 16.88 5.75 3.00 2.25 11.0 8.03 88.0
7 1017005 75,000 4,300 3 - 4 x 10.5 5.00 19.50 7.25 3.75 2.75 14.16 8.50 166.0
8 1017009 100,000 5,100 3-1/2 - 4 x 13.0 # 7.00 22.09 7.75 4.00 3.25 15.91 9.28 265.0
Contractors
* Ultimate Load is 5 times the Working Load Limit. † Long Bolts are designed to be used with soft metal (i.e., aluminum) work
** Ultimate Load is 4.5 times the Working Load Limit for 7000# Hoist Ring piece. While the long bolts may also be used with ferrous metal (i.e.,steel
Supply
when tested in 90 degree orientation. and iron) work piece, short bolts are designed for ferrous work pieces only.
‡ Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A 574.
# Hex head bolt used on Frame 8 (100,000 lb.) Hoist Ring.
Protection
Fall

375

Metric Swivel WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Hoist Rings
■ Top washer has the following features:
- The Working Load Limit and Recommended Torque
value are permanently stamped into each washer.
- Washer is color coded for easy identification: HR-125 M
Silver - Metric thread.
■ Individually Proof Tested to 2-1/2 times
Working Load Limit.
■ Bolt specification is a Grade 12.9 Alloy socket head
cap screw to Din 912. All threads listed are metric
(ASME/ANSI B18.3.1m).
■ Designed to be used with ferrous work piece only.
■ BOLT SIZE IDENTIFICATION: The size of the bolt
will be stated as in the drawing below. Illustration shows
meaning of each dimension given.
■ Frame 2 and larger RFID EQUIPPED.
■ Also available in Stainless Steel.
HR-125 M Metric Threads

Working Dimensions (mm)
HR-125 Load Limit
Frame Torque Effective Weight
M (kg)
Size in Thread Each
Stock Bolt Size Radius Dia.
No. At a 5:1 At a 4:1 Nm * Projection C D G H (kg)
No. A‡ E F
Design Design Length
Factor † Factor † B
1 1016602 400 500 10 M8 x 1.25 x 40 16.7 69.2 24.6 11.7 8.5 47.5 28.2 .17
1 1016613 450 550 16 M10 x 1.50 x 40 16.7 69.2 24.6 11.7 8.5 47.5 26.2 .18
2 1016624 1,050 1,300 38 M12 x 1.75 x 50 16.9 123 49.8 22.1 17.5 85.1 58.9 1.05
2 1016635 1,900 2,400 81 M16 x 2.00 x 60 26.9 123 49.8 22.1 17.5 85.1 54.9 1.11
2 1016644 2,150 2,700 136 M20 x 2.50 x 65 31.9 123 49.8 22.1 17.5 85.1 50.9 1.17
3 1016657 3,000 3,750 136 M20 x 2.50 x 75 27.8 167 75.2 34.5 25.4 124 74.4 3.09
3 1016668 4,200 5,250 312 M24 x 3.00 x 80 32.8 167 75.2 34.5 25.4 124 70.4 3.21
4 1016679 7,000 8,750 637 M30 x 3.50 x 120 61.7 222 94.2 44.5 30.5 157 101 6.53
5 1016690 11,000 13,750 1,005 M36 x 4.00 x 150 60.3 316 120 60.7 44.5 215 145 16.8
5 1016701 12,500 15,600 1,005 M42 x 4.50 x 160 70.3 316 120 60.7 44.5 215 139 17.4
5 1016712 13,500 16,900 1,350 M48 x 5.00 x 160 70.3 316 120 60.7 44.5 215 133 18.0
* The tightening torque values shown are based upon threads being clean, dry and free of lubrication.
† Individually proof loaded to 2-1/2 times the Working Load Limit based on the 4:1 design factor.
‡ Bolt specification is a Grade 12.9 Alloy socket head cap screw to Din 912. All threads are metric (ASME / ANSI B18.3.1m).
376

Heavy Lift Swivel WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Hoist Rings
■ Forged bail provides the following:
- Easily readable “Raised Lettering” showing the name Crosby
or “CG” and PIC Code for material traceability.
Hoists
- Greater durability providing the increased “Toughness”
desired in potentially abusive field conditions. HR-1000
- Larger opening than standard Hoist Ring bail.
■ Top washer is color coded for easy identification (Red for UNC
threads and Silver for Metric threads)
Services
■ The Working Load Limit and Recommended Torque value are
permanently stamped into each washer.
■ Individually Proof Tested to 2-1/2 times Working Load Limit.
■ Available in both UNC Thread and Metric Thread style.
■ BOLT SIZE IDENTIFICATION: The size of the bolt will be stated
Engineered
as in the drawing below. Illustration shows meaning of each
Products
dimension given.
HR-1000 UNC Threads
Slings
Dimensions (in.)
Working Effective
Frame HR-1000 Torque Weight
Load Thread
Size Stock in Bolt Size Radius Dia. Each
Limit Projection C D G H
No. No. Ft. Lbs. A‡ E F (lbs.)
(lbs.) * Length
Hardware
B
1 1068002 800 7 5/16 - 18 x 1.50 .52 3.69 .97 .62 .44 2.27 1.38 .60
1 1068006 1,000 12 3/8 - 16 x 1.50 .52 3.69 .97 .62 .44 2.27 1.38 .62
2 1068010 2,500 28 1/2 - 13 x 2.25 .69 6.26 1.96 1.25 .62 4.20 2.50 3.05
2† 1068014 2,500 28 1/2 - 13 x 2.75 1.19 6.26 1.96 1.25 .62 4.20 2.50 3.07
2 1068018 4,000 60 5/8 - 11 x 2.25 .69 6.26 1.96 1.25 .62 4.20 2.50 3.11
2† 1068022 4,000 60 5/8 - 11 x 3.00 1.44 6.26 1.96 1.25 .62 4.20 2.50 3.18
2 1068026 4,000 100 3/4 - 10 x 2.50 .94 6.26 1.96 1.25 .62 4.20 2.50 3.24
Products
Lifting
2† 1068030 5,000 100 3/4 - 10 x 3.00 1.44 6.26 1.96 1.25 .62 4.20 2.50 3.30
3 1068034 5,000 100 3/4 - 10 x 3.00 .85 8.66 2.96 1.63 1.00 6.25 3.25 10.09
3† 1068038 7,000 ** 100 3/4 - 10 x 3.50 1.35 8.66 2.96 1.63 1.00 6.25 3.25 10.21
3 1068042 7,000 ** 160 7/8 - 9 x 3.00 .85 8.66 2.96 1.63 1.00 6.24 3.25 10.21
3† 1068046 8,000 160 7/8 - 9 x 3.50 1.35 8.66 2.96 1.63 1.00 6.24 3.25 10.40
3 1068050 8,000 230 1 - 8 x 3.50 1.35 8.66 2.96 1.63 1.00 6.24 3.25 10.50
3† 1068054 10,000 230 1 - 8 x 4.50 2.35 8.66 2.96 1.63 1.00 6.24 3.25 10.72
4 1068058 15,000 470 1-1/4 - 7 x 5.00 2.09 11.21 3.71 2.00 1.25 7.82 4.00 21.90
4 1068062 24,000 800 1-1/2 - 6 x 6.50 2.59 11.21 4.71 2.00 1.25 7.82 4.00 23.00
Rope
Wire
HR-1000 Metric Threads
Working Dimensions (mm)
HR- Load Limit
Frame Torque Effective Weight
Cordage
1000M (kg) *
Size in Thread Each
Stock Bolt Size Radius Dia.
No. At a 5:1 At a 4:1 Nm Projection C D G H (kg)
No. A‡ E F
Design Design Length
Factor *** Factor *** B
1 1068307 400 500 10 M8 x 1.25 x 40 15.2 93.7 24.6 15.7 11.2 57.7 35.1 .3
Securement
1 1068316 450 550 16 M10 x 1.50 x 40 15.2 93.7 24.6 15.7 11.2 57.7 35.1 .3
2 1068325 1,050 1,300 38 M12 x 1.75 x 55 15.5 162 49.8 31.8 19.1 107 63.5 1.5
Load
2 1068334 1,900 2,400 81 M16 x 2.00 x 65 25.5 162 4938 31.8 19.1 107 63.5 1.5
2 1068343 2,150 2,700 136 M20 x 2.50 x 70 30.5 162 49.8 31.8 19.1 107 63.5 1.6
3 1068352 3,000 3,750 136 M20 x 2.50 x 80 25.4 220 75.2 41.4 25.4 159 82.6 4.6
3 1088361 4,200 5,250 312 M24 x 3.00 x 90 35.4 220 75.2 41.4 25.4 159 82.6 4.8
4 1068370 7,000 8,750 637 M30 x 3.50 x 140 66.2 285 94.2 50.8 31.8 199 102 9.7
4 1068369 11,000 13,750 1,005 M36 x 4.00 x 130 56.2 285 94.2 50.8 31.8 199 102 10.2
Contractors
* Ultimate Load is 5 times the Working Load Limit. ** Ultimate Load is 4.5 times the Working Load Limit for 7000# Hoist Ring when tested in 90 degree orientation.
Supply
*** Individually proof loaded to 2-1/2 times the Working Load Limit based on the 4:1 design factor. † Long Bolts are designed to be used with soft metal (i.e., aluminum)
work piece. While the long bolts may also be used with ferrous metal (i.e.,steel & iron) work piece, short bolts are designed for ferrous work pieces only.
‡ Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A 574. ‡‡ Bolt specification is a Grade 12.9 Alloy socket head cap screw to DIN 912.
Note: The tightening torque values shown are based upon threads being clean, dry and free of lubrication.
Protection
Fall

377

Safety Engineered
Hoist Rings
Material:
Alloy steel with minimum Heavy Duty®
tensile strength of 180,000 PSI.
Hoist Rings
Design Factor:
5:1, Magnetic Particle Inspected Material:
Per ASTM 1444, Hoist Rings Forged alloy steel with
retain the same rated load from minimum tensile strength
0 to 90 degrees from the bolt axis, of 180,000 PSI.
Standard tolerance +/- .030 inch
Design Factor:
unless otherwise specified.
Minimum Design Factor = 5:1,
Finish: Magnetic Particle Inspected
Black Oxide Finish for corrosion resistance, also available Per ASTM 1444, Hoist Rings
in Cadmium, Titanium-Cadmium, Nickel and other plating. retain the same rated load
from 0 to 90 degrees from
Range of Movement: the bolt axis
Swivel 360°, Pivot 180° under Load
Range of Movement:
Patent Numbers: Swivel 360°, Pivot 180° under Load
5,848,815
Specifications:
Available in sizes from: Meets Military Specification No. MIL-STD 209,
■ Standard Sizes: Meets ANSI / ASME B30.26
- 3/8" U-Bar (thread size 1/4"-20) to
5" U-Bar (thread size 6"-4) Finish:
- Rated load from 550 to 250,000 pounds Black Oxide Finish for corrosion resistance,
- Long Bar Models are available
■ Metric Sizes: Also available in a wide range of plating—
- Thread sizes from M8 x 1.25 to M90 x 6.00 e.g Cadmium, Titanium-Cadmium, Nickel, etc.
- Rated load from 400 kg to 51,000 kg
Typical Applications:
ADB's HEAVY DUTY® Hoist Rings are specified and
used in nuclear energy equipment
Patent:
#5,405,210
Available in sizes from:

■ Standard Sizes:
- .44" U-Bar (thread size 1/4"-20) to
1.25" U-Bar (thread size 2"-8)
- Rated load from 550 to 30,000 pounds
■ Metric Sizes:
- Thread sizes from M8 x 1.25 to M56 x 5.50
378

Side Pull
Cranes / Jibs
Overhead
Hoist Rings
Material:
Alloy Steel
(Certified Heat Treat)
E-Z® Torque
Hoist Rings
Hoists
Design Factor:
5:1, Magnetic Particle Material:
Inspected Alloy steel with minimum
tensile strength of 180,000 PSI.
Services
Range of Movement:
Swivel 360° Under Load Design Factor:
5:1, Magnetic Particle Inspected
Specifications: Per ASTM 1444. Hoist Rings
Engineered
Meets Military Specification No. retain the same rated load from
Products
MIL-STD 209J, Meets ASME B30.26 0 to 90 degrees from the bolt axis.
Finish: Range of Movement:
Black Oxide Finish for corrosion resistance Swivel 360°, Pivot 180° under Load
Slings
Finish:
■ Standard Sizes: Black Oxide finish for corrosion resistance
- 3/8" U-Bar (thread size 5/16"-18)
to 1-1/2" U-Bar (thread size 2"-8) Typical Applications:
- Rated load from 650 to 29,000 pounds ADB, the originator and leader in safety hoist rings,
Hardware
■ Metric Sizes: introduces another time and money saving innovation.
- Thread sizes from ADB's new EZ-Torque® Hoist Ring eliminates the need of
M8 x 1.25 to M64 x 6.00 locating and installing hydraulic torque multipliers for large
- Rated load from hoist ring installations. A 75,000 lb. rated load hoist ring
400 kg to 25,000 kg requires the mounting screw to be torqued to 4,300 ft. lbs.
Products
Lifting
Using ADB's EZ-Torque® Hoist Ring requires only a
standard torque wrench and 92 ft. lbs. of torque per bolt!
Patent Numbers:
5,848,815
Rope
Wire
Also available in a wide range of plating—
Cadmium, Titanium-Cadmium, Nickel, etc.
Cordage
■ Standard Sizes:
- 1.25" U-Bar (thread size 1-1/4"-7)
to 5" U-Bar (thread size 6"-4)
- Rated load from 15,000 to
250,000 pounds
Securement
■ Metric Sizes:
Load
- Thread sizes from

M30 x 3.50 to M90 x 6.00
- Rated load from 7,000 kg
to 51,000 kg
Contractors
Supply
Protection
Fall

379

Stainless Steel
Safety Hoist Rings
■ Actek swivel hoist rings are
designed for lifting. They rotate
and pivot to absorb any pitch,
roll or sway of unbalanced loads. Safety Swivel
Will not yield to heavy side loads.
Help prevent the lifting hook Hoist Rings
from disengaging.
■ Safety Engineered. All loads lifted are especially Actek Mfg. & Eng. Inc. hoist rings
important from a safety standpoint. Actek swivel hoist are manufactured using AISI 4140
rings provide the kind of safety that protects men Aircraft Quality Chrome-Moly,
and material against accidents before they occur. which meet or exceed ASTM A322.
■ For use in outdoor weather and certain chemical and All Actek 4140 material is
corrosive environments. metallurgically analyzed and
■ Material: 300 Series Stainless Steel. certified. All Actek hoist rings
■ Safety Factor: 5:1. are heat treated to MIL-H-6875
■ Liquid Penetrant MIL 6866. and magnetic particle inspected to accordance with
ASME Section 5, Article 7. Actek hoist rings meet or
Available in sizes from: exceed all the requirements of ASME B30.26.
■ Standard Sizes:
- Thread sizes from 5/16"-18 to 3-1/2"-4 Actek swivel hoist rings include safety-engineered style,
- Rated load from 400 to 50,000 pounds forged style, and stainless steel hoist rings. We offer
■ Metric Sizes: different plating options also. Other hoist rings include side
- Thread sizes from M8 x 1.25 to M90 x 6.00 load, flip-flop, mold-handler, speed base, round base,
- Rated load from 200 kg to 22,300 kg pivot plate hoist rings. Custom made hoist rings are also
available to suit all of your lifting needs.
Each Actek hoist ring is 200% Proof-load Tested and

Side Pull Hoist Rings individually serial numbered for better trace-ability.
Each hoist ring is individually packaged, shipped with
■ Designed for side-mounted applications a certificate of conformance, safety precaution, and
■ Smooth swiveling and pivoting action. additional safety information.
■ Aircraft Quality “Chrome Moly”,
Strong & Tough. Swivel Hoist Rings are designed for lifting at any angle
■ Extra large ring accepts many because they can swivel 360° and pivot 180°. Therefore,
styles and sizes of hoist hooks. the rated load remains the same, regardless of the angle
■ Ideal for stamping and injection of force. As a result, you increase safety and peace of
mold industries. mind. Hoist rings are available with a rated load ranging
■ Magnetic particle inspected. from 800 lbs. to 250,000 lbs. with a 5:1 design safety factor.
■ Rated loads from 650 lbs. to 29,000 lbs.
■ Thread size from 5/16" to 2” Available in sizes from:
■ Safety Factor: 5:1 ■ Standard Sizes:
■ Also available in Metric Sizes - 3/8" U-Bar (thread size 1/4"-20) to
5" U-Bar (thread size 6"-4)
Available in sizes from: - Rated load from 600 to 250,000 pounds
■ Standard Sizes: ■ Metric Sizes:
- Thread sizes from 5/16"-18 to 2"-8 - Thread sizes from M45 x 4.50 to M90 x 6.00
- Rated load from 650 to 29,000 pounds - Rated load from 9,500 kg to 44,600 kg
■ Metric Sizes:
- Thread sizes from M8 x 1.25 to M48 x 5.00
380

Traditional Center Pull
Cranes / Jibs
Overhead
Hoist Rings
Popular sized hoist rings
(1/2-13 through 1-8) are offered
with two or more length bolts.
Side Pull Style
Hoists
Use the longer lengths with softer
parent materials, the shorter lengths
with hard materials, such as steel. Hoist Rings
■ Full 360° Swivel and 180° Pivot Action The full swivel and pivot action
Services
■ Rated at 5:1 Strength Factor of the Jergens Hoist Ring allows
■ Material: Alloy Steel you to flip and turn parts
■ Finish: Black Oxide (Except Washer) without unhooking. Plus, the
■ U-Bar, Bolt, Pins, Base, Washer and Bushing extra-large diameter rings
let you use almost any size hook.
Engineered
are Magnetic Particle Inspected
Products
■ Washer: Zinc Plated with Gold Colored (Inch),
■ Convenient part handling
Clear / Blue (Metric) Conversion Coating
■ Rated at 5:1 Strength Factor
■ Proof Tested to 200% of Rated Load Capacity
■ Material: Alloy Steel
■ Certificate of Proof Test provided
■ Clevis, Ring, Bushing and Cap Screw are
■ 3D Solid Models available in multiple formats
Slings
■ magnetic particle inspected
CE Certified
■ Clevis is x-rayed
■ Long Bar sizes available
■ Finish: Black Oxide
■ Also available in Metric sizes
■ 200% Proof Tested
■ Ask about different finishes / coatings
■ Available in FixtureProTM Design Software
Hardware
and PartSpec CD
■
Shackle-LokTM Hoist Ring
Stated load capacity based on specific thread
torques as shown in chart.
■ It is recommended that these torques be used
Jergens Shackle-LokTM combines
when installing hoist rings.
Products
the strength of a hoist ring with
Lifting
■ CE Certified
the versatility of a shackle. Its unique, ■ Also available in Metric sizes
3-piece design is ideal for use with ■ Ask about different finishes / coatings
a variety of lift methods, and shackles
are interchangeable. Shackle-LokTM
is simply the industry’s most efficient
Rope
Wire
below-the-hook lifting device from a
weight-to-load rating ratio.
■ Internal ball bearings (440 Stainless Steel) allow
Cordage
for smooth rotation under load
■ Full 360° Swivel and 180° Pivot Action
■ Easy to remove shackle
■ Rated 5:1 Strength Factor in Vertical Pull
■ Bolt & Base Material: Alloy Steel 4140; C40-44
Securement
■ Bolt and Base Finish: Black Oxide

Load
■ Bolt and Base are Magnetic Particle Inspected

■ Shackle & Shackle Pin: 1035 Carbon Steel; C18-24
■ Shackle Finish: Zinc Plated with Gold Colored
Conversion Coating
Contractors
■
Supply
Proof Tested to 200% of Rated Load Capacity

■ Certificate of Proof Test provided
■ Also available in Metric sizes
Protection
Fall

381

WBG-V WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Load Ring Bolted

360° Swivelling / 180° Pivoting
Complies with the machinery directives 2006/42/EG
Swivelling lifting point:

■ Loadable in any direction. Safety factor 4:1.
■ Turnable under load in vertical direction.
■ Not suitable for permanent swivelling under full load,
especially in 90° direction.
■ Simple installation, just a thread hole is required.
■ Variable lengths (Vario) available.
■ Can also be used for through holes. Nominal WLL -
■ Bolts 100% magnetic crack detected. Surface protection worst case.
CORRUD-DT (20 times better than zinc plating). Ring not adjusted
to pull direction
■ High tensile, approved suspension ring acc. EN 1677-4.
■ Surface: Ring red powder coating, housing zinc plated.
■ Type Vario with washer and 100% crack detected nut.
■ WBG-V and WBG are also available with Imperial thread.
■ Turning without jerk due to additional bush bearing washer.
■ Wear marks in the main load directions 45°, 60° and 90°.
Measurements in Inches Ref. No.

Weight
WLL Ref. No. Vario with Manually adjusted
Type Stand. Torque - increased WLL -
(lbs.) A B C D E
F
G M SW X (lbs.)
Stand. Washer
Stand. and Nut ( )-values.
VWBG-V 660 (880)

5/16 1-5/16 1-5/32 1-3/16 3 1/2 1-27/64 5/16 1-1/8 45/64 0.57 7991090 –
0.3-5/16"-18UNC [1320]
VWBG-V 990 (1300)

5/16 1-5/16 1-5/32 1-27/64 3-1/16 43/64 1-1/2 3/8 1-3/16 3/4 0.64 7991091 –
0.45-3/8"-16UNC [1980]
According to the user instructions
VWBG-V 0.3- 1,320 (1,650)

3/8 2 1-3/8 1-21/32 4-1/8 13/16 1-25/32 1/2 1-27/64 3/4 0.9 7991092 –
5/16"-13UNC [2,640]
VWBG-V 2,860 (3,300)

1/2 1-7/8 1-1/2 1-7/8 4-13/32 1-5/32 2-1/8 5/8 1-5/8 1-7/64 1.3 7991093 –
1.3-5/8"-11UNC [5,720]
VWBG-V 4,400 (5,500)

1/2 2-3/16 1-3/8 2-1/2 5-5/16 1-1/8 2-9/16 3/4 2-5/32 1-3/16 3.09 7991094 –
2.0-3/4"-10UNC [8,800]
VWBG-V 7,700 (8,800)

11/16 2-11/16 1-9/16 3-3/16 6-25/32 1-1/2 3-7/16 1 2-3/4 63/64 5.8 7991095 –
3.5-1"-8UNC [15,400]
Vertical load
VWBG-V 11,000 (13,200) (straight pull) - double
7/8 2-3/16 1-31/32 3-7/8 8-11/16 1-7/8 4/18 1-1/4 3-11/32 1-1/4 11.22 7991096 – nominal WLL -
5.0-1-1/4"-7UNC [22,000]
Please Note: It can happen, that during use, the lifting point can engage in any position. That´s why the WLL is embossed for the worst case
situation. The ring can be manually adjusted to the direction of pull, then the WLL values in the brackets ( ) can be used.
Attention: Refer to RUD user instructions.
The WLL (Working Load Limit) is listed at the nominal value (worst case scenario) unless otherwise specified.
382

WBG WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Load Ring Bolted
360° Swivelling / 180° Pivoting
with a Ball Bearing
Hoists
For heavy loads, which have to be turned and swivelled.
■ With ball bearings. Swivels under full load.
Services
■ Not suitable for permanent swivelling under full load,
especially in 90° direction.
■ Loadable in any direction. Safety factor 4:1.
■
Suspension ring manufactured acc. EN 1677-4 grade 80
(100% magnetic crack detected and proof loaded).
Engineered
Nominal WLL -
Products
■ S = max. allowed gap. worst case.
Ring not adjusted
■ WBG New: Wear marks in the main load directions to pull direction
45°, 60° and 90°.
Safety Notice:
Please provide plain bolting surface. The countersunk for the
Slings
thread should be: thread diameter plus 4 mm (15 inch). The base
material of the workpiece must be capable to withstand the
occurring lifting forces. Minimum required material = ST 37 (1.0037).
Hardware
Measurements in Inches Ref. No.
WLL Weight
Type F
vario * Torque
(lbs.) A B C ØD E F G M SW (lbs.) F F
vario *
Max. Manually adjusted
- increased WLL -
VWBG 8(10) 8 (10) Per
7/8 3-3/8 1-31/32 3-17/32 8-3/16 2-1/4 11-1/2 3-11/16 1-1/2 3-1/8 10.6 8600451 ( )-values.
t-1-1/2"-6UNC [15] Request
Products
Lifting
VWBG 12(13) 12 (13) Per
1 4-13/32 2-9/16 3-27/32 9-1/4 2-5/8 11-1/2 3-3/4 1-3/4 3-11/32 13.5 8600452
According to the user instructions
VWBG 13(16) 13 (16) Per

1 4-13/16 2-9/16 3-27/32 9-1/4 3 11-1/2 3-3/4 2 3-11/32 13.5 8600453
t-2"-4.5UNC [18] Request
VWBG 16(22) 16 (22) Per

1-1/4 4-11/16 2-3/4 4-3/4 10-25/32 3-11/32 11-1/2 4-3/4 2-1/4 3-3/4 24.3 8600454
t-2-1/4"-4.5UNC [28] Request
Rope
Wire
VWBG 16(22) 16 (25) Per
1-1/4 4-11/16 2-3/4 4-3/4 10-25/32 4-3/32 11-1/2 4-3/4 2-3/4 3-3/4 26.5 8600455
VWBG 31.5(25) 31.5 (40) Per

1-13/16 5-1/8 3-17/32 6-11/16 13-5/16 4-1/2 11-1/2 6-1/4 3 5-11/16 58.1 8600456
t-3"-4UNC [50] Request
Cordage
VWBG 35(48) 30 (48) Per
1-13/16 5-1/8 3-17/32 6-11/16 13-5/16 5-15/64 11-1/2 6-1/4 3-1/2 5-11/16 61.9 8600457
Vertical load
VWBG 40(50) 40 (50) Per
1-13/16 5-1/8 13-5/16 6-11/16 13-5/16 5-7/8 11-1/2 6-1/4 4 5-11/16 66.3 8600157 (straight pull)
t-4"-4UNC [50] Request Securement
CAUTION: During lifting, the ring of the lifting point can engage in any position. The embossed WLL is for the worst case scenario.
If the ring is manually adjusted to the horizontal position, higher WLL values in brackets ( ) can be chosen. In case of straight pull
Load
(vertical load direction) Maximum WLL can be chosen.
Contractors
Supply
Protection
Fall

383

VLBG WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Load Ring Bolted

... Will Turn 360°
■ UD Universal bolts and nuts for VLBG - 100% crack detected.

R
■ The hex-head-bolt is suitable for internal and external wrench
mounting for types with metric threads.
■ Surface protection: CORRUD - DT - at least 20 times better
corrosion protection than zinc plating (except for the spot face)
after length shortening.
■ Thread over whole bolting length "H".
■ Bolt is held captive in the body. Replace only with the same
quality class bolt.
■ Clear identification at the bolt head: RUD, thread size, quality class.
■ The load ring must be installed perpendicular to the workpiece.
The workpiece must be flat, providing complete contact for the load
ring bushing.
■ Load ring has to be adjusted in pull direction, free to move and
must not support on edges.
■ Use according to user instructions and by trained persons.
■ The lifting attachment must be free to move when attached
to the load ring.
■ Regular inspections should be carried out by a competent person
(BGR 500).
■ Load should not be turned during lifting.
Weight
Nom. Measurements in Inches Torque Ref. No.
Type WLL (Standard)
(lbs.) ft-
A B C D E F G H J K L M SW R T DB lbs.
lbs.
LBG-Z
1T 1/2"- 2,200 1-1/4 2-1/8 1-11/32 1-1/2 1-15/32 13/32 1-5/32 7/8 2-15/32 1-25/32 1-31/32 1/2 3/4 1-1/4 2-15/16 1 .72 75 8502349
13UNC
VLBG-Z
1.5T 5/8"- 3,300 1-5/16 2-3/16 1-13/32 1-13/16 1-1/2 17/32 1-13/32 15/16 3-27/64 1-27/32 2-3/8 5/8 15/16 1-1/2 3-11/32 1-13/16 1.2 110 8502350
11UNC
VLBG-Z
2.5T 3/4"- 5,500 1-31/32 3-1/4 2-1/8 2-13/64 2-1/8 21-32 1-11/16 1-7/64 4-7/16 2-17/32 2-13/16 3/4 1-1/8 1-7/8 4-11/32 1-3/4 2.85 185 8502351
10UNC
VLBG-Z
2.5T 7/8"- 5,500 1-31/32 3-1/4 2-1/8 2-9/32 2-3/64 21/32 1-11/16 1-1/16 4-7/16 2-17/32 2-34 7/8 1-5/16 1-7/8 4-11/33 1-3/4 2.85 225 8502352
9UNC
VLBG-
Z 4T 1"- 8,800 1-31/32 3-1/4 2-1/8 2-13/32 2-33/64 23/32 1-11/16 1-5/8 5-1/8 3-1/16 3-5/16 1 1-1/2 1-7/8 4-15/16 1-3/4 3.3 300 8502353
8UNC
VLBG-Z
5T 1-1/4"- 11,000 2-3/8 4-1/16 2-9/16 3-5/32 2-33-64 7/8 2-13/32 1-5/8 5-15/16 3-5/32 4-1/64 1-1/4 1-7/8 2-5/8 5-25/32 2-3/8 7.25 370 8503187
7UNC
VLBG Load Ring will turn 360°, adjustable in pull direction. Load ring foldable, full WLL in any load direction, surface pink powder coated.
BG = German Employers Requires: The max. lengths of the RUD - bolts are adjusted in such a way that if a hex-head-shaped nut (DIN EN ISO
7042) is used, assemblies of material thickness of approximately 8 *M (for M8 - M30) and 5 *M for (M36 - M48) can be realized respectively.
384

VRBS / RBSB WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Load Ring For Welding
■ istribution of the load force due to the 2 point fixing, hence an

D
Hoists
optimized force introduction to the workpiece.
■ Forged, suspension ring according to EN 1677-1, electromagnetic
crack detected, pink powder coated. Suspension ring can also
be ordered single. For instance VRL 4. This lifting point fulfils
the requirements of the appropriate safety authorities (German
Services
Employers Insurance Association). Stamped .
■ Lays flat when not in use.
■ Low profile.
■ Rounded well shaped design.
■ High dynamic and static strength.
Engineered
■ The welding blocks are forged out of the ideal weldable steel
Products
ST52-3N (S355J2+N) and the nominal WLL is embossed.
■ Patented distance lugs assist in achieving the correct
root weld (approx. 3 mm).
■ The weld arrangement (continuous HY weld) fulfils the
requirements of DIN 18800 i.e. the closed weld avoids corrosion
Slings
and is thus suitable for outdoor use.
RBSB Application
■ The weldable load ring with limit stops is available for
Hardware
EHB containers and machines. The limit stops provide the
necessary support for the ring and thus enabling a
45° hook - in inclined position from the work piece.
■ Protects the load from severe damage.
Products
Lifting
Nominal Measurements in Inches
Weld Weight Ref.
Type WLL
HV + a (lbs.) No.
(lbs.) A B C D E F O Q X T
VRBS 4 8,800 2-29/64 5/8 1-7/64 1-7/8 5-5/16 2-51/64 21/32 3-1/32 9/16 2-9/16 HV 4 + 3 1.8 7992826
VRBS 6.7 15,000 3-15/32 25/32 1-17/32 2-3/8 6-11/16 3-19/32 29/32 3-31/32 19/32 3-5/16 HV 5.5 + 3 4 7992489
Rope
Wire
VRBS 10 22,000 3-15/32 7/8 1-13/16 2-9/16 7-11/16 3-15/16 1-7/64 4-11/64 7/8 3-3/4 HV 6 + 4 6.2 7992489
VRBS 16 35,200 5-1/8 1-3/16 2-1/4 3-35/64 10-7/16 5-9/32 1-13/32 5-25/32 1-7/64 5 HV 8.5 + 4 14.5 7992490
VRBS 30 66,000 6-19/64 1-21/32 3-5/64 5-1/8 14-49/64 7-43/64 1-55/64 8-21/32 1-29/64 7 HV 15 + 4 42 60267
Cordage
VRBS 50 110,000 9-7/16 2-3/4 4-23/32 9-1/16 24-13/32 13-3/8 2-9/16 14-31/32 – 12-21/64 HV 25 + 8 120 56834
WLL Measurements in Inches Weld Weight Ref.

Type
(lbs.) HV + a (lbs.) No.
A B C D E F O P T
Securement
RBSB 11,000 3-9/64 3/4 1-1/2 2-3/8 6-7/16 3-5/8 29/32 7/8 3-5/16 HV 5 + 3 4 61757
Load
Attention: Refer to RUD user welding instructions.
Contractors
Supply
Protection
Fall

385

VLBS WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Load Ring For Welding

■ The VLBS forged out of high tensile CrNiMo - steel with an

innovative design offers many advantages.
- Up to 50 % higher WLL.
- The two protective supporting lugs (inside the load ring)
are patented and they improve the connection with
the attachment in addition to the protected clamping spring.
- The support effect is exceptional, especially if the
ring is side loaded or the lifting point is welded on an
uneven workpiece.
- Pink powder coating, a VIP recognition attribute and a
heat indicator.
■ Easy and quick to weld assembly.
■ Compact and shapely design.
■ High dynamic and static strength.
■ Forged suspension ring acc. to EN 1677, grade 80,
electromagnetic crack detected, pink powder coated; meets the
requirements of the appropriate safety authorities.
■ The welding block has been forged of material 1.0570 (St 52-3)
and clearly stamped with the permissible WLL. The patented
distance lugs assist in achieving the correct root weld.
■
Important: By the special weld design (continuous HV), the
requirements of DIN 18800 are fulfilled, i.e., a closed weld avoids
corrosion and thus suitable for outdoor use.
■ Distinctive features for type LBS-U: A protected spring maintains
the load ring in every required position. The parts are assembled in
such a way that they remain captive.
■
The spring reduces vibration induced noise.
Nominal Measurements in Inches

Weight Ref.
Type WLL Weld
(lbs.) No.
(lbs.) A B C D E F G H I T
VLBS 1.5 3,300 1-1/4 2-5/8 1-1/2 1 1-9/16 17/32 1-19/64 3-7/16 9/16 2-9/16 HV 5+ 3 0.8 7993035
VLBS 2.5 5,500 1-13/32 3-1/32 1-3/4 1-1/16 1-7/8 17/32 1-19/32 3-13/16 5/8 2-15/16 HV 5+ 3 1.1 7994830
VLBS 4 8,800 1-21/32 3-27/64 2 1-1/4 2-3/64 21/32 1-13/16 4-13/32 45/64 3-16/64 HV 5+ 3 1.8 7993036
VLBS 6.7 15,000 2-13/32 4-15/32 2-5/8 1-47/64 2-7/8 7/8 2-3/8 6-3/16 15/16 4-21/32 HV 5+ 3 4.2 7993037
VLBS 10 22,000 2-61/64 5-5/64 2-5/8 2-5/32 2-51/64 1-3/64 2-3/8 6-13/16 1-3/64 4-31/32 HV 5+ 3 6.4 7993040
VLBS 16 35,300 3-3/4 7-31/64 3-15/16 2-23/32 4-1/8 1-1/64 3-35/64 9-9/16 1-37/64 6-55/64 HV 5+ 3 15 7993041 (w/o spring)
Attention: Refer to RUD user welding instructions.
386

Malleable Clips— WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Zinc plated
■ Intended for use in making eye termination in right
regular lay wire rope. Such an assembly is for
non-critical light-duty use where a small applied load
Hoists
is expected. For this reason, an efficiency of the
termination is not stated.
■ Cast iron base.
■ Steel U-bolt and nuts.
Services
Engineered
Zinc plated—Bulk
Products
Trade Minimum Amount of Required Weight
Part Bulk
Size Number of Rope to Turn Torque Each
Number Packed
(in.) Clips Per Eye Back in Inches Ft. Lbs. (lbs.)
252 00081 1/16 2 4-3/4 1.5 500/BX .02
252 00086 1/8 3 4-3/4 3.0 500/BX .04
Slings
252 00091 3/16 3 5-1/2 4.5 500/BX .08
252 00096 1/4 3 7 15 250/BX .12
252 00101 5/16 3 7-3/4 15 250/BX .15
252 00106 3/8 3 9-1/2 30 250/BX .22
252 00111 7/16 3 10-1/4 40 100/BX .33
Hardware
252 00116 1/2 4 15-1/4 45 100/BX .37
252 00121 9/16 4 16 50 100/BG .59
252 00126 5/8 4 16 75 100/BG .58
252 00131 3/4 5 22-1/4 75 100/BG .84
252 00136 7/8 5 23-1/2 130 50/BG 1.25
Products
252 00141 1 6 31 130 40/BG 1.56
Lifting
252 00146 1-1/8 7 39-1/2 200 10/BG 2.50
252 00147 1-1/4 8 50 200 10/BG 3.15
252 00148 1-3/8 8 50 360 10/BG 4.45
252 00149 1-1/2 9 60-1/2 360 10/BG 5.20
Zinc plated—Boxed Qty.
Rope
Wire
252 00151 1/16 2 4-3/4 1.5 25/BX .02
252 00156 1/8 3 4-3/4 3.0 25/BX .04
252 00161 3/16 3 5-1/2 4.5 25/BX .08
252 00166 1/4 3 7 15 25/BX .12
252 00171 5/16 3 7-3/4 15 25/BX .15
Cordage
252 00176 3/8 3 9-1/2 30 25/BX .22
252 00181 7/16 3 10-1/4 40 25/BX .33
252 00186 1/2 4 15-1/4 75 25/BX .37
252 00191 5/8 4 16 75 10/BX .59
252 00196 3/4 5 22-1/4 75 10/BX .84
Securement
Load
WARNING: Never use malleable clips for critical, heavy-duty or overhead loads!
Contractors
Supply
Protection
Fall

387

A-341 Alloy
Pear Shaped Links
■ Alloy Steel - Quenched and Tempered
■ Individually Proof Tested at 2 times Working Load Limit
with certification.
■ Proof Test certification shipped with each link.
■ Sizes 1/2", 5/8", 3/4", 7/8", 1", 1-1/4" and 1-3/8"
are forged.
A-341 Working Weight Dimensions

Size
Stock Load Limit Per (in.)
in. No. lbs. * t lbs. B C F
1/2 1013575 7,000 3.15 .55 3.00 2.00 1.00
5/8 1013584 9,000 4.09 1.10 3.75 2.50 1.25
3/4 1013595 12,300 5.59 1.76 4.50 3.00 1.50
7/8 1013604 15,000 6.81 2.82 5.25 3.50 1.75
1 1013613 24,360 11 4.22 6.00 4.00 2.00
†† 1-1/8 1013622 30,600 13.9 6.25 6.50 4.50 2.25
1-1/4 1013631 36,000 16.4 8.25 7.75 5.00 2.50
1-3/8 1013640 43,000 19.5 11.25 8.25 5.50 2.75
†† 1-1/2 1013649 54,300 24.7 14.25 9.00 6.00 3.00
†† 1-5/8 1013658 62,600 28.4 18.50 9.75 6.50 3.25
†† 1-3/4 1013667 84,900 38.6 22.50 10.50 7.00 3.50
†† 1-7/8 1013676 95,800 43.5 29 11.25 7.50 3.75 * Based on single leg sling (in-line
†† 2 1013685 102,600 46.6 34 12.00 8.00 4.00 load), or resultant load on multiple
†† 2-1/4 1013694 143,100 65 48 13.50 9.00 4.50
legs with an included angle less
†† 2-1/2 1013703 147,300 66.9 66 15.00 10.00 5.00
than or equal to 120°.
†† 2-3/4 1013712 216,900 98.6 88 16.50 11.00 5.50
†† 3 1013721 228,000 103 114 18.00 12.00 6.00 Minimum Ultimate load is 5 times
†† 3-1/4 1013730 262,200 119 146 19.50 13.00 6.50 the Working Load Limit.
†† 3-1/2 1013739 279,000 126 181 21.00 14.00 7.00 †† Welded Link.
†† 4 1013748 373,000 169 271 24.00 16.00 8.00
G-341 / S-341
Weldless Sling Links
■ Forged carbon steel - Quenched and Tempered.
■ Self Colored or Hot Dip galvanized.
WLL
Size Single
No. Each (in.)
Pull
G-341 S-341
in. lbs. * lbs. B C F
Galv. S.C.
3/8 1013897 1013904 1,800 .23 2.25 1.50 .75
1/2 1013913 1013922 2,900 .55 3.00 2.00 1.00
5/8 1013931 1013940 4,200 1.06 3.75 2.50 1.25
3/4 1013959 1013968 6,000 1.88 4.50 3.00 1.50
7/8 1013977 1013986 8,300 2.75 5.25 3.50 1.75
1 1013995 1014002 10,800 4.35 6.00 4.00 2.00
1-1/4 1014011 1014020 16,750 7.60 7.50 5.00 2.50
1-3/8 1014039 1014048 20,500 11.30 8.25 5.50 2.75
* Ultimate Load is 6 times the Working Load Limit. Based on single leg sling (in-line load), or resultant load on multiple legs
with an included angle less than or equal to 120°.
388

G-340 / S-340
Cranes / Jibs
Overhead
Weldless End Links
G-340 from 5/8" thru 7/8" meet the performance
requirements of Federal Specification RR-C-271F,
Type XV, except for those provisions required
Hoists
of the contractor.
■ Forged carbon steel - Quenched and Tempered

■ Self Colored or Hot Dip galvanized.
Services
Size WLL
No. Each (in.)
G-340 S-340
Engineered
in. lbs. * lbs. B C D
Products
Galv. S.C.
5/16 1014057 1014066 2,500 .15 .50 1.75 1.18
3/8 1014075 1014084 3,800 .22 .56 1.88 1.38
1/2 1014093 1014100 6,500 .49 .75 2.38 1.81
5/8 1014119 1014128 9,300 .97 1.00 3.25 2.32
3/4 1014137 1014146 14,000 1.51 1.13 3.50 2.68
Slings
7/8 1014155 1014164 12,000 2.59 2.00 5.13 3.75
1 1014173 1014182 15,200 3.95 2.25 5.75 4.25
1-1/4 1014191 1014208 26,400 7.30 2.50 7.00 5.00
1-3/8 1014217 1014226 30,000 10.38 2.75 7.75 5.50
* Ultimate Load is 6 times the Working Load Limit. Based on single leg sling (in-line load), or resultant load on multiple legs
Hardware
with an included angle less than or equal to 120°.
S-643
Products
Weldless Rings
Lifting
Weldless Rings meet the performance requirements of
Federal Specification RRC-271F Type VI, except for those
provisions required of the contractor.
Rope
Wire
■ Forged carbon steel - Quenched and Tempered.
■ Self Colored
Cordage
Size S-643 WLL Weight Dimensions
A Stock Single Pull Each (in.)
in. No. lbs. * lbs. B C
7/8 x 4 1013780 7,200 2.72 4.00 5.75
Securement
7/8 x 5-1/2 1013806 5,600 3.47 5.50 7.25

1x4 1013824 10,800 3.69 4.00 6.00
Load
1-1/8 x 4 1013842 10,400 6.60 6.00 8.25

1-1/4 x 5 1013860 17,000 6.82 5.00 7.50
1-3/8 x 6 1013888 19,000 10.12 6.00 8.75
Contractors
* Ultimate Load is 6 times the Working Load Limit.

Supply
Protection
Fall

389

A-342 Alloy
Master Links
■ Alloy Steel — Quenched and Tempered.
■ Individually Proof Tested to values shown, with
certification.
■ Proof Tested with 60% inside width special fixtures
sized to prevent localized point leading per
ASME A-952.
■ Meets or exceeds all requirements of ASME B30.26,
proof load and temperature requirements.
Importantly, these links meet other critical performance
ASME B30.26.
■ Forgings have a Product Identification Code (PIC)
for material traceability, along with the size, the name
Crosby and USA in raised lettering.
■ Selected sizes designated with “W” in the size column Containers. These Crosby master links are
have enlarged inside dimensions to allow additional 100% proof tested, MPI and impact tested. The tests
room for sling hardware and crane hook. are conducted by Crosby and 3.1 test certification is
■ Crosby 1-1/4" to 2" 342/345 master links are type available upon request.
approved to DNV Certification Notes 2.7-1- Offshore ■ Incorporates patented QUIC-CHECK® deformation
indicators.
Stock Weight Proof Dimensions

Size WLL
No. Each Load (in.)
Deformation
in. A-342 lbs. lbs. * lbs. ** A B C
Indicator
1/2W 1014266 1.3 7,400 17,200 .62 2.80 5 3.50
5/8 1014280 1.5 9,000 18,000 .62 3 6 3.50
3/4W 1014285 2 12,300 28,400 .73 3.20 6 4
7/8W 1014319 3.3 15,200 35,200 .88 3.75 6.38 4.50
1W 1014331 6.1 26,000 60,000 1.10 4.30 7.50 5.50
1-1/4W 1014348 12 39,100 90,400 1.33 5.50 9.50 7
1-1/2W 1014365 18.6 61,100 141,200 1.61 5.90 10.50 7.50
1-3/4 1014388 25.2 84,900 169,800 1.75 6 12 7.50
2 1014404 37 102,600 205,200 2.00 7 14 9
2-1/4 1014422 54.1 143,100 289,200 2.25 8 16 10
2-1/2 1014468 68.5 160,000 320,000 2.50 8.38 16 11
2-3/4 1014440 94 216,900 433,800 2.75 9.88 18 12.50
3 1014486 115 228,000 456,000 3.00 9.88 18 13
3-1/4 1014501 145 262,200 524,400 3.25 10 20 13.50
3-1/2 1014529 200 279,000 558,000 3.50 12 24 15.50
3-3/4 1015051 198 336,000 672,000 3.75 10 20 13.50
4 1015060 264 373,000 746,000 4.00 12 24 16
†† 4-1/4 1015067 302 354,000 708,000 4.25 12 24 –
†† 4-1/2 1015079 345 360,000 720,000 4.50 14 28 –
†† 4-3/4 1015088 436 389,000 778,000 4.75 14 28 –
†† 5 1015094 516 395,000 790,000 5.00 15 30 –
* Ultimate Load is 5 times the Working Load Limit. Based on single leg sling (in-line load), or resultant load on multiple legs with an
included angle less than or equal to 120 degrees. Applications with wire rope and synthetic sling generally require a design factor of 5.
** Proof Test Load equals or exceeds the requirement of ASTM A952(8.1) and ASME B30.9.
†† Welded Master Link.
390

Open Pear Master Links WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
SK System (SKO)
■ Excellent choice for single leg sling of chain,
synthetic or wire rope
■ Part of Gunnebo Lifting’s SK System of custom
Hoists
rigging solutions. Can be connected to any
other SK component.
■ Full traceability for each component
■ Each of the components has been Proof tested
Services
and certified
■ Includes Half Link fitting
Engineered
Products
Working Weight
Model Chain Size Dimension (Inches)
Grade Load Limit * Each
Slings
No.
in mm at 90° L L1 B G B1 lbs.
SKO-7/8-8 9/32 7 80 3,500 3.9 5 2 .55 .59 .88
SKO-7/8-8 5/16 8 80 4,500 3.9 5 2 .55 .59 .88
10-87/8-10 3/8 10 80 7,100 5 6.3 2.6 .71 .79 1.3
Hardware
SKO-13-8 1/2 13 80 12,000 5.7 7.4 2.8 .87 1 2.2
SKO-16-8 5/8 16 80 18,100 6.9 8.9 3.2 1 1.2 3.5
SKO-18/20-8 3/4 20 80 28,300 8 10.5 4.1 1.2 1.4 5.7
* Design Factor 5:1 proof tested and certified
Products
Lifting
Rope
Wire
Cordage
Securement
Load
Contractors
Supply
Protection
Fall

391

Wide Master Links WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
■ Alloy Steel • Quenched & Tempered

■ Individual Proof Test Certification* with each link
■ 60% inside width special fixtures sized to
prevent localized point loading per ASTM A-952
■ All links marked with material heat code for
traceability, size, SKOOKUM and USA
■ Links 1-1/2" and smaller are drop forged
■ Links 1-3/4" and larger are robotically welded
■ Ultimate Load is 5 times the Working Load Limit
■ Made in USA
Skookum Master Links are available in any diameter

and any size. Please contact your Lifting Specialist for
any custom product or non-standard sizes.
Weight Working Load Working Load

Size Dimensions (in)
Stock Each Limit (lbs.) Limit (lbs.) Painted Forged /
No. @ 5:1 @ 4:1 Finish Welded
in. mm lbs. Design Factor Design Factor A B C
1/2 13 AMF0500 .8 7,000 8,750 .5 2.5 5 Orange Forged
5/8 16 AMF0625 1.5 9,000 11,250 .63 3 6 Orange Forged
3/4 19 AMF0750 2.1 12,300 15,375 .75 2.75 5.5 Orange Forged
1 26 AMF1000 4.9 24,360 30,450 1 3.5 7 Orange Forged
1-1/4 32 AMF1250 9.6 39,100 48,875 1.25 4.38 8.75 Orange Forged
1-1/2 38 AMF1500 16.2 54,300 67,875 1.5 5.25 10.5 Orange Forged
1-3/4 44 AMW1750 25.2 84,900 106,125 1.75 6 12 Orange Welded
2 51 AMW2000 37 102,600 128,250 2 7 14 Orange Welded
2-3/4 70 AMW2750 87.7 216,900 271,125 2.75 9.5 16 Orange Welded
3-1/2 89 AMW3500 200 279,000 348,750 3.5 12 24 Orange Welded
7 178 AMW7000 1390 826,500 1,033,125 7 21 42 Orange Welded
7-1/2 191 AMW7500 1711 969,760 1,212,200 7.5 22 44 Orange Welded
8 203 AMW8000 2075 1,102,000 1,377,500 8 24 48 Orange Welded
8-1/2 216 AMW8500 2491 1,322,400 1,653,000 8.5 25 50 Orange Welded
* Sizes 3-1/2" and above are proof tested at customer request only, a certificate of conformance is still provided.
392

Design-A-Link WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
We provide an endless possibility for special B
products and assemblies with:
■ Custom Shapes
Oblong
Link
C
Hoists
A
■ Special Marking
■ OEM Private Labeling
■ Custom Engineering
■ Product Development
Services
■ Certifications
■ Alloy, Carbon Steel, Stainless Steel
Master
Link
Engineered
Products
CUSTOMER INFORMATION:
Customer = ____________________________
SO # = ____________________________
Slings
DWG # = ____________________________ D
Link
Name: ____________________________
Phone: ____________________________
Hardware
DIMENSIONS:
A = ____________________________
B = ____________________________ Triangle
Products
Link
Lifting
C = ____________________________
D = ____________________________
Capacity = ____________________________
Rope
Wire
Quantity = ____________________________
Materials: ____________________________
Pear
Link
Testing
Cordage
Requirements: ____________________________
Finish
Requirements: ____________________________
Securement
Application: ____________________________
Load
Other
NOTES: ____________________________
____________________________
Contractors
____________________________
Supply
____________________________
Protection
Fall

393

G-411 Standard
Wire Rope Thimbles
G-411 meets the performance requirements of
Federal Specification FF-T-276b Type II, except for
those provisions required of the contractor.
■ Hot Dip galvanized steel.

■ The standard choice for light duty applications
and loading conditions.
Rope Diameter Stock No. Weight Per 100 Dimensions (in.)

in. mm G-411 lbs. A B C D E F G H
1/8 3-4 1037256 3.5 1.94 1.31 1.06 0.69 0.25 0.16 0.05 0.13
3/16 5 1037274 3.5 1.94 1.31 1.06 0.69 0.31 0.22 0.05 0.13
1/4 6-7 1037292 3.5 1.94 1.31 1.06 0.69 0.38 0.28 0.05 0.13
5/16 8 1037318 4 2.13 1.5 1.25 0.81 0.44 0.34 0.05 0.13
3/8 9-10 1037336 6.7 2.38 1.63 1.47 0.94 0.53 0.41 0.06 0.16
1/2 11-13 1037354 12.5 2.75 1.88 1.75 1.13 0.69 0.53 0.08 0.19
5/8 16 1037372 34.5 3.5 2.25 2.38 1.38 0.91 0.66 0.13 0.34
3/4 18-20 1037390 47.1 3.75 2.5 2.69 1.63 1.08 0.78 0.14 0.34
7/8 22 1037416 84.6 5 3.5 3.19 1.88 1.27 0.94 0.16 0.44
1 24-26 1037434 97.5 5.69 4.25 3.75 2.5 1.39 1.06 0.16 0.41
1-1/8 - 1-1/4 28-32 1037452 175 6.25 4.5 4.31 2.75 1.75 1.31 0.22 0.5
■ Stainless steel recommended for more corrosive

G-414 Extra Heavy environments where greater protection is required.
Wire Rope Thimbles ■

Greater protection against wear and deformation
of the wire rope eye.
■ Longer service life.
G-414 meets the performance requirements of
Federal Specification FF-T-276b Type III, except for
those provisions required of the contractor.
■ Available in Hot Dip galvanized or Stainless Steel

(Type 304).
Rope Diameter Stock No. Weight Per 100 Dimensions (in.)

in. mm G-414 SS-414 lbs. A B C D E F G H
*1/4 6-7 1037639 1037960 6.5 2.19 1.62 1.5 0.88 0.41 0.28 0.06 0.25
* 5/16 8 1037657 1037988 11.8 2.5 1.88 1.81 1.06 0.5 0.34 0.08 0.3
* 3/8 9-10 1037675 1038004 21.6 2.88 2.12 2.12 1.12 0.63 0.41 0.11 0.39
7/16 11-12 1037693 – 34.7 3.25 2.38 2.38 1.25 0.72 0.47 0.12 0.45
* 1/2 - 9/16 13-15 1037719 1038022 51 3.62 2.75 2.75 1.5 0.89 0.59 0.15 0.48
* 5/8 16 1037755 1038040 75.7 4.25 3.25 3.12 1.75 1 0.66 0.16 0.53
* 3/4 18-20 1037773 1038068 158.1 5 3.75 3.81 2 1.22 0.78 0.22 0.69
7/8 22 1037791 – 177.8 5.5 4.25 4.25 2.25 1.38 0.94 0.22 0.78
1 24-26 1037817 – 313.9 6.12 4.5 4.75 2.5 1.56 1.06 0.25 0.88
1-1/8 - 1-1/4 28-32 1037835 – 400 7 5.12 5.88 2.88 1.88 1.31 0.25 1.25
1-1/4 - 1-3/8 32-35 1037853 – 886 9.08 6.5 6.81 3.5 2.25 1.44 0.37 1.29
1-3/8 - 1-1/2 35-38 1037871 – 1294.8 9 6.25 7.12 3.5 2.62 1.56 0.5 1.31
1-5/8 40 1037899 – 1700 11.25 8 8.12 4 3 1.72 0.5 1.38
1-3/4 44 1037915 – 1775 12.19 9 8.5 4.5 3.06 1.84 0.5 1.5
1-7/8 - 2 48-52 1037933 – 2775 15.12 12 10.38 6 3.38 2.09 0.5 1.69
2-1/4 56 1037951 – 3950 17.5 14 11.88 7 3.88 2.38 0.62 1.82
* SS-414 sizes available in stainless steel type 304
394

G-408 Open Pattern
Cranes / Jibs
Overhead
Wire Rope Thimbles
■ Hot Dip galvanized Steel.
■ Recommended for light duty applications in
which it is being assembled into another fitting
Hoists
(i.e., shackle or master link).
Services
Rope Stock Weight Dimensions
Engineered
Products
Diameter No. Per 100 (in.)
in. mm G-408 lbs. A B C D E F
1/4 6-7 1037531 3 0.28 0.69 1.06 1.41 2.03 0.38
5/16 8 1037559 3.8 0.34 0.81 1.25 1.53 2.16 0.5
3/8 9-10 1037577 7 0.44 0.94 1.47 1.72 2.47 0.62
1/2 11-13 1037595 12.5 0.53 1.12 1.75 1.47 2.84 0.75
Slings
5/8 16 1037611 25 0.66 1.38 2.38 2.34 3.59 1
G-412 Solid
Wire Rope Thimbles
Hardware
■ Cast Ductile Iron.
■ Fits pin for open wire rope socket, boom pendant
clevis and wedge socket.
Products
Lifting
Rope Stock Weight Dimensions
Rope
Wire
Diameter No. Per 100 (in.)
in. mm G-412 lbs. A B C D E F G H J K L
1/2 13 1037121 0.61 2.81 1.75 0.25 1.06 0.75 0.56 0.28 0.88 2.13 1.63 1.56
5/8 16 1037149 2.21 4.69 3 0.38 1.31 1.06 0.81 0.41 1.13 3.38 2.25 2.56
3/4 18-20 1037167 2.32 4.69 3 0.38 1.5 1.06 0.81 0.41 1.38 3.38 2.25 2.56
Cordage
7/8 22 1037185 5.45 6.06 3.81 0.5 1.75 1.38 1.06 0.53 1.63 4.5 3.25 3.44
1 24-26 1037201 5.25 6.06 3.81 0.5 2.13 1.38 1.06 0.53 1.81 4.5 3.25 3.44
1-1/8 28-30 1037229 9.29 7.25 4.56 0.63 2.38 1.75 1.31 0.66 2.06 5.38 3.88 4.06
1-1/4 - 1-3/8 32-35 1037247 9.81 7.25 4.56 0.63 2.63 1.94 1.53 0.78 2.31 5.38 3.88 4.13 Securement
Load
Contractors
Supply
Protection
Fall

395

Special Thimbles
Slip-Thru Thimbles are designed to allow passage
of an identical thimble through its eye. This is a necessity
when a regular sling is used as a choker sling. Slip-Thru
Thimbles also prevent the eye of the sling from mashing
together and the top of the eye wearing excessively.
The generous inside dimensions allow the thimbles to
fit large crane hooks. Rope retention ears are tapered so
they can be bent or peened over wire rope.
Thimble Sling Size (in.) Dimensions (in.) Weight

Number Single 8 Parts 6 Parts A B C D E F G (lbs.)
W-2 5/16-3/8 3/32-1/8 3/32-1/8 2-1/8 4-1/8 7/16 13/16 9/16 3-1/4 5-1/4 1.3
W-3 1/2-9/16 3/16 3/16 2-3/8 4-3/8 5/8 1 5/8 4 6 1.5
W-4 5/8-3/4 1/4 1/4-5/16 3-3/8 6-5/8 13/16 1-5/16 5/8 5-3/8 8-1/2 3.4
W-5 7/8-1 5/16 3/8 3-3/4 7-1/8 1-1/8 1-5/8 7/8 6-1/4 9-3/8 5.6
W-6 1-1/8 to 1-1/4 3/8 7/16 4-3/8 8-3/8 1-3/8 1-7/8 1 7-1/8 11 8.6
W-7 1-3/8 to 1-1/2 7/16-1/2 1/2 5 9-1/2 1-5/8 2-1/8 1-1/4 8-1/8 12-1/2 10
W-8 1-5/8 to 1-3/4 9/16 5/8 6-3/4 11-3/4 1-13/16 2-9/16 1-7/16 9-3/8 14-3/4 17.6
W-9 1-7/8 to 2 5/8 3/4 8 14-1/2 2-1/8 3-1/4 1-7/8 13 19-1/4 53
W-10 2-1/8 to 2-1/4 3/4 7/8-1 8 15-1/2 2-1/2 3-3/4 2 13 20-3/8 70
W-11 2-1/2 to 3 7/8-1 1-1/8 9 18-1/2 3-3/16 4-11/16 2-1/2 15-3/4 24-3/4 126
Crescent Thimbles are designed to protect the

bearing surface of a loop where a large dimension loop
is necessary. The ears are tapered so that they can be
bent or peened over wire rope. Standard-Laid Rope Size
3/8" to 3".
Thimble Sling Size (in.) Dimensions (in.) Weight

Number Single 8 Parts 6 Parts A B C D E F G H (lbs.)
6C 3/8-7/16 3/32-1/8 1/8 2 1 27/32 15/32 2-1/16 3/8 1/2 3/8 .50
8C 1/2-9/16 3/16 3/16 2-1/4 1-1/8 1 5/8 2-1/2 1/2 1/2 1/2 .75
9C 5/8 – 1/4 2-3/4 1-3/8 1-5/32 23/32 3 19/32 9/16 19/32 1.2
10C 3/4 1/4 5/16 3-1/4 1-5/8 1-5/16 13/16 3-1/2 5/8 5/8 5/8 2
14C 7/8 – – 4-1/2 2-1/4 1-7/16 15/16 4-5/16 3/4 11/16 3/4 3.3
16C 1 5/16 3/8 4-1/2 2-1/4 1-9/16 1-1/16 4-19/32 13/16 3/4 7/8 3.75
18C 1-1/8 3/8 7/16 4-7/8 2-7/16 1-13/16 1-1/4 5-1/32 7/8 7/8 1 5
20C 1-1/4 7/16 1/2 5-1/2 2-3/4 2-1/16 1-7/16 5-3/4 15/16 15/16 1-1/8 6.75
22C 1-3/8 to 1-1/2 1/2 9/16 6 3 2-1/4 1-5/8 6-1/4 1-1/16 1-1/8 1-3/16 8
24C 1-5/8 9/16 5/8 6-1/2 3-1/4 2-1/2 1-3/4 6-11/16 1-1/8 1-1/4 1-1/4 12
28C 1-3/4 to 1-7/8 – – 7 3-1/2 2-15/16 1-15/16 7-3/8 1-1/4 1-3/8 1-1/2 16.6
23C 2 5/8 3/4 7 3-1/2 3-3/16 2-3/16 7-13/16 1-1/2 1-1/2 1-5/8 21.80
40C 2-1/4 to 2-1/2 3/4-7/8 1 8-1/2 4-1/4 4-1/8 2-7/8 9-5/8 1-5/8 1-7/8 2 39
48C 2-3/4 to 3 1 1-1/8 10 5 4-7/8 3-3/8 11-1/4 1-3/4 2-1/4 2-1/2 67
396

Special Thimbles
Cranes / Jibs
Overhead
(Continued)
The No. 83 Casing Thimble has been designed
for the oil industry. The Choker Thimbles, No. 82, No. 84,
No. 85, No. 86 and No. 87 are designed especially
Hoists
for braided choker slings. The ears can be peened over
to retain wire rope.
Services
Thimble Sling Size (in.) Fits Choker Dimensions (in.) Weight
Engineered
Products
Number Single 8 Parts Hook A B C D E F G H (lbs.)
82 1/8 1/8 #2 1/2 7/8 1-1/4 2-1/8 3-1/4 1/4 3/8 5/16 .7
83 1/4 3/16 #3 5/8 1 1-1/2 2-1/2 3-7/8 1/4 1/2 3/8 1.1
84 5/16 1/4 #4 13/16 1-5/16 1-3/4 2-7/8 4-7/16 5/16 5/8 7/16 1.8
85 3/8 5/16 #5 15/16 1-7/16 2 3-1/4 5 5/16 3/4 1/2 2.2
86 7/16 3/8 #6 1-1/8 1-11/16 2-1/4 3-5/8 5-3/4 3/8 7/8 9/16 3.3
Slings
87 1/2 7/16 #7 1-3/8 1-15/16 2-3/4 4-1/16 6-3/8 3/8 1 11/16 4.7
Equalizing Thimble—Single and double groove.

Provides for the adjustment of the length of the legs of bridle
Hardware
slings so as to lift unbalanced loads evenly. Makes all bridle
slings more versatile while eliminating center ring and two
splices. Material: Cast electric steel.
Products
Lifting
Rope
Wire
Size Rope Dimensions (in.)
Thimble Weight
Diameter
Number A B C D E F (lbs.)
(in.)
3E 3/8-7/16 4-1/2 3 6-7/16 4-5/8 7/8 1/2 3
Cordage
4E 1/2-9/16 6 4 8-1/2 6-3/16 1-1/8 5/8 6.3
6E 5/8-3/4 7 4-1/2 9-15/16 7 1-7/16 15/16 11
8E 7/8-1 7-1/8 5 10-3/4 8-3/4 1-13/16 1-3/16 15.6
10E 1-1/8 to 1-1/4 10 6-1/2 14-3/8 10-7/8 2-3/16 1-7/16 30
12E 1-3/8 to 1-1/2 11 7-1/2 15-7/8 11-3/4 2-9/16 1-11/16 39
14E 1-5/8 to 1-3/4 15 9 20-13/16 14-1/4 2-15/16 1-15/16 71
Securement
16E 1-7/8 to 2 15 9 21-5/8 14-7/8 3-5/16 2-3/16 85

Load
* DG6E 5/8-3/4 8-1/4 5-1/2 11-1/4 8 2-3/8 1-3/4 21

* DG8E 7/8-1 9 6 12-3/4 8-1/2 2-7/8 2-1/4 28
* DG10E 1-1/8 to 1-1/4 11-1/4 7-1/4 15-7/8 12-1/8 3-9/16 2-5/8 50
Contractors
* Note: DG—designates double groove equalizing thimble.

Supply
Protection
Fall

397

Boom Pendant Thimbles
Illustrated below is a NEWCO Boom Pendant fabricated
with a flemish eye splice and swaged steel sleeves which
fit around a pendant fitting that is either open or closed.
Available In sizes from 9/16" to 2-3/8". Pendants are not
to be used for any other purpose other than Boom Pendant
application. NEWCO Pendant Thimbles are interchangeable
with standard sockets. Weight on open pendant includes
pin (D) and cotter.
Wire Rope Closed Dimensions & Data (in.) Est.

Diameter Weight
(in.) A B C D E F G (lbs.)
9/16 to 5/8 4-3/2 3-1/8 1-1/4 1-1/16 1-1/16 11/16 2-1/8 1.7
3/4 4-27/32 3-5/8 1-7/16 1-5/16 1-3/16 13/16 2-1/2 2.6
7/8 5-5/16 4-1/8 1-11/16 1-1/2 1-3/8 15/16 2-3/4 3.5
1 5-31/32 4-9/16 2-1/16 1-3/4 1-5/8 1-1/8 3 4.6
1-1/8 6-3/8 5-1/16 2-5/16 2 1-3/4 1-1/4 3-1/4 5.6
1-1/4 to 1-3/8 7-3/8 6-1/8 2-9/16 2-1/4 2-1/8 1-1/2 4 9.6
1-1/2 8-3/16 6-3/4 2-13/16 2-1/2 2-3/8 1-5/8 4-1/2 14
1-5/8 10-7/16 8 3-1/16 2-5/8 2-1/2 1-3/4 5-1/2 29
1-3/4 to 1-7/8 12-5/16 9-3/4 3-9/16 3-1/8 3 2 7 41
2 to 2-1/8 13 10-1/2 3-13/16 3-7/16 3-1/4 2-1/4 7-1/2 57
2-1/4 to 2-3/8 17-5/16 11-3/4 4-3/8 3-7/8 3-5/8 2-1/2 8-1/2 76
Wire Rope Open Dimensions & Data (in.) Est.

Diameter Weight
(in.) A B C D E F G H J L P R (lbs.)
9/16 to 5/8 8-3/64 2-3/8 1-1/4 1-3/16 15/32 11/16 2-1/8 3-1/8 2-17/32 4-1/4 2-9/32 9/16 5.3
3/4 9-3/32 2-13/16 1-1/2 1-3/8 17/32 13/16 2-1/2 3-5/8 3-1/32 4-3/4 2-3/4 21/32 7.5
7/8 10-5/16 3-1/4 1-3/4 1-5/8 5/8 15/16 2-3/4 4-1/8 3-1/4 5-1/4 3-1/4 3/4 12.5
1 11-11/16 3-3/4 2 2 3/4 1-1/18 3 4-9/16 3-11/16 5-7/8 3-7/8 7/8 19
1-1/8 12-25/32 4-1/4 2-1/4 2-1/4 7/8 1-1/4 3-1/4 5-1/16 3-27/32 6-17/32 4-7/16 1 26
1-1/4 to 1-3/8 15-1/32 4-3/4 2-1/2 2-1/2 15/16 1-1/2 4 6-1/8 4-5/16 8 4-15/16 1-1/8 39
1-1/2 17-1/8 5-3/8 3 2-3/4 1-1/16 1-5/8 4-1/2 6-3/4 4-13/16 9-1/8 5-5/8 1-3/16 56
1-5/8 20-1/2 5-5/8 3 3 1-3/16 1-3/4 5-1/2 8 6-7/16 10-5/8 6-1/8 1-5/16 78
1-3/4 to 1-7/8 24-1/16 6-5/8 3-1/2 3-1/2 1-5/16 2 7 9-3/4 7-7/16 12-3/4 6-7/8 1-9/16 125
2 to 2-1/8 27 7-5/8 4 3-3/4 1-11/16 2-1/4 8 10-3/4 9-3/4 13-1/4 7-1/8 1-13/16 166
398

Special Thimbles—
Cranes / Jibs
Overhead
Stainless Steel
Stainless Steel
Wire Rope Thimbles—
Type 304
Hoists
Services
Engineered
Products
Wire Dimensions (in.) Weight
Rope Size
(lbs.)
(in.) A B C D
Slings
1/16 .10 .28 .48 .03 .30/100
1/16 - 5/64 .09 .31 .62 .03 .40/100
3/32 - 1/8 .12 .38 .72 .03 .50/100
5/32 .14 .43 .73 .04 .74/100
3/16 .20 .55 .78 .04 .01
Hardware
1/4 .25 .69 .95 .05 .02
5/16 .34 .78 1.40 .06 .04
3/8 .42 .94 1.70 .06 .06
1/2 .54 1.20 1.85 .06 .08
9/16 .60 1.36 2.05 .06 .10
Products
Lifting
5/8 .68 1.45 2.37 .07 .17
3/4 .76 1.60 2.63 .08 .21
7/8 .95 1.90 3.10 .09 .39
1 1.05 2.08 3.36 .09 .49
Rope
Wire
Cordage
Securement
Load
Contractors
Supply
Protection
Fall

399

S-326A / S-3326 WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
SHUR-LOC® Swivel Hooks

■ Forged Alloy Steel — Quenched and Tempered.
■ Individually Proof Tested at 2-1/2 times the
4:1 Working Load Limit with certification.
■ Recessed trigger design is flush with the hook body, S-326A S-3326
protecting the trigger from potential damage. Swivel Hook Swivel Hook
■ Easy to operate with enlarged thumb access.
■ Positive Lock Latch is Self-Locking when hook is loaded. w/ Bearing
■ Rated for both Wire Rope and use with Grade 80/100 Chain.
■ G-414 Heavy Thimble should be used with wire rope slings.
■ Trigger repair Kit available (S-4316). Consists of spring,
roll pin and trigger.
■ S-3326 Swivel Hook utilizes anti-friction bearing design,
which allows hook to rotate freely under load.
■ Fatigue rated.
■ The SHUR-LOC® hook, if properly installed and locked,
can be used for personnel lifting applications and meets the
intent of OSHA Rule 1926.1431(g)(1)(i)(A) and
1926.1501(g)(4)(iv)(B).
■ "Look for the Platinum Color – Crosby Grade 100 Alloy Products".
■ U.S. Patent 5,381,650 and foreign equivalents.
Use in corrosive environment requires shank and nut inspection

in accordance with ASME B 30.10-1.10.4 (b)(5)(c) 2009.
S-326A SHUR-LOC® Swivel Hooks—Suitable for infrequent, non-continuous rotation under load.
Wire Rope
Chain Grade 100 XXIP IWRC Stock Weight Dimensions
Size Alloy Chain Mechanical No. Each (in.)
Working Splice
Load Limit WLL
(lbs.) 4:1 Size S-
in. mm (lbs.) lbs. A B C D E F H J L AA
(in.) 1326
5:1 *
– 6 3,200 5/16 2,200 1004304 1.26 1.50 1.32 6.13 .79 2.60 .67 .50 .63 1.13 1.50
1/4-5/16 7-8 5,700 7/16 4,200 1004313 2.62 1.75 1.59 7.60 1.10 3.50 .87 .63 .81 1.38 2.00
3/8 10 8,800 1/2 5,600 1004322 4.70 2.00 1.73 8.83 1.17 4.39 1.10 .75 .94 1.75 2.50
1/2 13 15,000 5/8 8,600 1004331 8.64 2.50 2.38 11.20 1.67 5.45 1.26 1.00 1.16 2.11 3.00
5/8 16 22,600 7/8 16,600 1004340 17.00 2.75 2.53 12.90 2.05 6.56 1.50 1.13 1.50 2.49 3.50
3/4 18-20 35,300 1 22,000 1004349 24.00 2.83 2.52 14.10 2.22 7.76 2.01 1.10 2.03 3.52 5.00
7/8 22 44,100 1-1/8 26,500 1004358 29.00 3.44 3.19 16.40 2.45 8.75 2.26 1.30 2.20 3.83 6.00
S-3326 SHUR-LOC® Swivel Hooks with Bearing—Suitable for frequent rotation under load.
Wire Rope
Chain Grade 100 XXIP IWRC Stock Weight Dimensions
Size Alloy Chain Mechanical No. Each (in.)
Working Splice
Load Limit WLL
(lbs.) 4:1 Size S-
in. mm (lbs.) lbs. A B C D E F H J L AA
(in.) 13326
5:1 *
– 6 3,200 5/16 2,200 1004404 1.50 1.50 1.14 6.17 .79 2.60 .67 .50 .63 1.13 1.50
1/4-5/16 7-8 5,700 7/16 4,200 1004413 3.10 1.75 1.52 7.54 1.10 3.50 .87 .63 .81 1.44 2.00
3/8 10 8,800 1/2 5,600 1004422 5.26 2.00 1.61 8.88 1.17 4.39 1.10 .75 .94 1.83 2.50
1/2 13 15,000 5/8 8,600 1004431 11.22 2.50 2.03 11.11 1.67 5.45 1.26 1.00 1.16 2.19 3.00
5/8 16 22,600 7/8 16,600 1004440 17.32 2.75 1.98 12.90 2.05 6.56 1.50 1.13 1.50 2.61 3.50
400

S-320 / S-320N Eye Hooks WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
All Crosby 320 Eye Hoist Hooks
incorporate the following features:
■ The most complete line
Hoists
of Eye hoist hooks. The following additional features have
■ Available in carbon steel been incorporated in the new Crosby
and alloy steel. S-320N Eye Hoist Hooks.
■ Designed with a
5:1 Design Factor for
Services
(Carbon Steel); Sizes 3/4 metric ton Carbon
4:1 Design Factor for through 22 metric ton Alloy
(Alloy Steel).
■ Eye hooks are load rated. ■ Metric Rated at
Engineered
5:1 Design Factor for
Products
■ Proper design, careful forging and precision controlled
quenched and tempering give maximum strength (Carbon Steel);
without excessive weight and bulk. 4:1 Design Factor for
■ Every Crosby Eye Hook has a pre-drilled cam, which (Alloy Steel).
can be equipped with a latch. Even years after purchase ■ Can be proof tested to 2 times the working Load Limit.
of the original hook, latch assemblies can be added. ■ Low profile hook tip.
Slings
■ Chemical analysis and tensile tests performed on each ■ New integrated latch (S-4320) meets the World class
PIC to verify chemistry and mechanical properties. standard for lifting.
■ Type Approval and certification in accordance ■ Heavy-duty stamped latch interlocks with the hook tip.
with ABS 2006 Steel Vessel Rules 1-1-17.7, and ■ High cycle, long life spring.
Hardware
ABS Guide for Certification of Cranes. ■ When secured with proper cotter pin through the hole
■ Hoist hooks incorporate two types of strategically in the tip of hook, meets the intent of OSHA Rule
placed markings forged into the product, 1926.1431(g) and 1926.1501(g) for personnel hoisting.
which address two (2) QUIC-CHECK® features: ■ Fatigue rated at 1-1/2 times the Working Load Limit
- Deformation Indicators and Angle Indicators. at 20,000 cycles.
Products
Lifting
Working Load Limit Eye Hook Replacement
(t) * Stock No. Latch Kits
Hook Weight
Carbon Alloy
Rope
ID Each
Wire
Carbon
Code S-320C S-320A (lbs.) S-4320 PL SS-4055
Carbon Alloy G-320CN
S-320CN S-320AN Stock No. Stock No. Stock No.
Galv.
S.C. S.C.
3/4 1 †D 1022200 1022208 1022375 .61 1096325 – –
Cordage
1 1-1/2 †F 1022211 1022219 1022386 .89 1096374 – –
1-1/2 2 †G 1022222 1022230 1022397 1.44 1096421 – –
2 3 †H 1022233 1022241 1022406 2.07 1096468 – –
3 5 †I 1022244 1022249 1022419 4.30 1096515 1092000 –
5 7 †J 1022255 1022262 1022430 8.30 1096562 1092001 –
7-1/2 11 †K 1022264 1022274 1022441 15.00 1096609 1092002 –
Securement
10 15 †L 1022277 1022285 1022452 20.77 1096657 1092003 –

15 22 †N 1022288 1022296 1022465 39.50 1096704 1092004 –
Load
20 30 O 1023289 – 1023546 60 – 1093716 1090161

25 37 P 1023305 – 1023564 105 – 1093717 1090189
30 45 S 1023323 – 1023582 148 – 1093718 1090189
40 60 T 1023341 – 1023608 228 – 1093719 1090205
Contractors
* Eye Hooks (3/4 TC - 22TA), Proof load is 2 times Working Load Limit. Eye Hooks (20 TC - 60TA). All carbon hooks-average straightening
Supply
load (ultimate load) is 5 times Working Load Limit. Alloy eye hooks 1 ton through 22 ton-average straightening load (ultimate load) is 5 times
Working Load Limit. Alloy eye hooks 30 tons through 60 tons-average straightening load (ultimate load) is 4.5 times Working Load Limit.
† New 320N style hook.
Protection
Fall

401

S-322CN / S-322AN WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Swivel Hooks
■ Forged — Quenched and Tempered.
■ Swivel hooks are load rated.
■ Proper design, careful forging, and precision controlled
quench and tempering gives maximum strength without
excessive weight and bulk.
■ Low profile hook tip designed to utilize Crosby S-4320
or PL-N latch kit. Simply purchase the latch assemblies.
Even years after purchase of the original hook,
latch assemblies can be added.
■ Hoist hooks incorporate markings forged into the
product which address two (2) QUIC-CHECK® features:
- Deformation Indicators—Two strategically placed
marks, one just below the shank or eye and the
other on the hook tip, which allows for a
QUIC-CHECK® measurement to determine if ■ Type Approval and certification in accordance with
the throat opening has changed, thus indicating ABS 2006 Steel Vessel Rules 1-1-17.7, and
abuse or overload. ABS Guide for Certification of Cranes.
- Angle Indicators—Indicate the maximum included ■ U.S. Patents 5,381,650 & 5,193,480 & 5,103,755
angle which is allowed between two (2) sling legs and foreign equivalents.
in the hook. These indicators also provide the This hook is a positioning device and is not intended to
opportunity to approximate other included angles rotate under load. Use in corrosive environment requires
between two sling legs. shank and nut inspection in accordance with ASME
B30.10-1.10.4 (b)(5)(c) 2009.
Working S-322 S-322 Rep.

Weight Dimensions
Load Limit CN AN Latch
Each (in.)
(t) * Stock Stock Stock
(lbs.)
Carbon Alloy No. No. A B C D F G H J K L M O† R S AA No.
3/4 1 1048600 1048804 .75 2.00 .82 1.25 2.86 1.25 .73 .81 .93 .63 5.66 .63 .89 4.55 38 1.50 1096325
1 1-1/2 1048609 1048813 1.25 2.50 1.31 1.50 3.15 1.38 .84 .94 .97 .71 6.71 .71 .91 5.37 .50 2.00 1096374
1-1/2 2 1048618 1048822 2.25 3.00 1.50 1.75 3.59 1.50 1.00 1.16 1.06 .88 7.75 .88 1.00 6.12 .63 2.00 1096421
2 3 1048627 1048831 2.30 3.00 1.50 1.75 4.00 1.62 1.13 1.31 1.19 .94 8.25 .94 1.09 6.50 .63 2.00 1096468
3 5 1048636 1048837 4.96 3.50 1.64 2.00 4.84 2.00 1.44 1.63 1.50 1.31 9.69 1.13 1.36 7.50 .75 2.50 1096515
5 7 1048645 1048854 10.29 4.56 2.29 2.50 6.28 2.50 1.81 2.06 1.78 1.66 12.47 1.44 1.61 9.63 1.00 3.00 1096562
7-1/2 11 1048654 1048865 19.40 5.00 2.53 2.75 7.54 3.00 2.25 2.63 2.41 1.88 14.75 1.63 2.08 11.37 1.13 4.00 1096609
10 15 1048663 1048877 23.25 5.62 2.48 3.12 8.34 3.25 2.59 2.94 2.62 2.16 16.40 1.94 2.27 12.25 1.25 4.00 1096657
15 22 1048672 1048886 47 7.10 3.76 4.10 10.34 4.25 3.00 3.50 3.41 2.69 21.34 2.38 3.02 16.71 1.50 5.00 1096704
– 30 – 1025688 70.50 7.10 3.76 4.10 13.62 5.00 3.61 4.63 4.00 3.00 23.25 3.00 3.25 18.01 1.50 6.50 1093716
Working L-322 L-322 Rep.

Weight Dimensions
Load Limit CN AN Latch
Each (in.)
(t) * Stock Stock Stock
(lbs.)
Carbon Alloy No. No. A B C D F G H J K L M O† R S AA No.
3/4 1 1048603 1048807 .75 2.00 .82 1.25 2.86 1.25 .73 .81 .93 .63 5.66 .63 .89 4.55 38 1.50 1096325
1 1-1/2 104862 1048816 1.25 2.50 1.31 1.50 3.15 1.38 .84 .94 .97 .71 6.71 .71 .91 5.37 .50 2.00 1096374
1-1/2 2 1048621 1048825 2.25 3.00 1.50 1.75 3.59 1.50 1.00 1.16 1.06 .88 7.75 .88 1.00 6.12 .63 2.00 1096421
2 3 1048630 1048834 2.30 3.00 1.50 1.75 4.00 1.62 1.13 1.31 1.19 .94 8.25 .94 1.09 6.50 .63 2.00 1096468
3 5 1048639 1048840 4.96 3.50 1.64 2.00 4.84 2.00 1.44 1.63 1.50 1.31 9.69 1.13 1.36 7.50 .75 2.50 1096515
5 7 1048648 1048859 10.29 4.56 2.29 2.50 6.28 2.50 1.81 2.06 1.78 1.66 12.47 1.44 1.61 9.63 1.00 3.00 1096562
7-1/2 11 1048657 1048868 19.40 5.00 2.53 2.75 7.54 3.00 2.25 2.63 2.41 1.88 14.75 1.63 2.08 11.37 1.13 4.00 1096609
10 15 1048666 1048880 23.25 5.62 2.48 3.12 8.34 3.25 2.59 2.94 2.62 2.16 16.40 1.94 2.27 12.25 1.25 4.00 1096657
15 22 1048675 1048889 47 7.10 3.76 4.10 10.34 4.25 3.00 3.50 3.41 2.69 21.34 2.38 3.02 16.71 1.50 5.00 1096704
– 30 – – 70.50 7.10 3.76 4.10 13.62 5.00 3.61 4.63 4.00 3.00 23.25 3.00 3.25 18.01 1.50 6.50 1093716
* Note: Carbon swivel hooks .75tC-15tC: proof load is 2 times working load limit. Designed with a 5 to 1 design factor.
Alloy swivel hooks 1tA-22A: proof load is 2.5 times working load limit. Designed with a 4.5 to 1 design factor.
Alloy swivel hook 30tA: proof load is 2 times working load limit. Designed with a 4 to 1 design factor.
† Dimensions for hooks 3/4 ton carbon thru 22t alloy are for S-4320 latch kits. Dimensions for hooks 31.5t alloy are for PL latch kit.
402

G-401 Chain Swivels /
Cranes / Jibs
Overhead
G-402 Regular Swivels
G-401 Chain Swivels meet the performance requirements
of Federal Specification RR-C-271F, Type VII, Class 1,
Hoists
G-402 Regular Swivels meet the performance requirements
of Federal Specification RR-C-271F, Type VII, Class 2,
Services
■ Hot Dip Galvanized
■ Quenched & Tempered
■ Crosby products meet or exceed all requirements
of ASME B30.26, including identification, ductility,
Engineered
Products
design factor, proof load and temperature requirements.
Importantly, Crosby products meet other critical
performance requirements, including fatigue life, impact
properties and material traceability, not addressed
by ASME B30.26.
■ 401, 402 and 403 swivels are positioning devices and
Slings
are not intended to rotate under load. Use in corrosive
environment requires shank and nut inspection in
accordance with ASME B30.10-1.10.4(b)(5)(c)2009.
Hardware
G-401 Chain Swivel
Working
Size Load
No. Each (in.)
Limit
in. G-401 lbs. * lbs. A B C D E G J M R U V
Products
Lifting
1/4 1016233 850 .13 1.25 .69 .75 .62 1.12 .25 .69 .31 2.25 1.69 1.25
5/16 1016251 1,250 .25 1.63 .81 1.00 .75 1.38 .31 .81 .38 2.72 2.06 1.47
3/8 1016279 2,250 .54 2.00 .94 1.25 1.00 1.75 .38 1.00 .50 3.44 2.50 1.88
1/2 1016297 3,600 1.12 2.50 1.31 1.50 1.25 2.25 .50 1.31 .63 4.25 3.19 2.44
5/8 1016313 5,200 2.09 3.00 1.56 1.75 1.50 2.75 .62 1.50 .75 5.13 3.88 2.94
Rope
Wire
3/4 1016331 7,200 3.09 3.50 1.75 2.00 1.75 3.25 .75 1.88 .88 5.78 4.94 3.46
G-402 Regular Swivel

Stock Working Weight Dimensions
Size
Cordage
No. Load Limit Each (in.)
in. G-402 lbs. * lbs. A B C D J M R S
1/4 1016019 850 .21 1.25 .69 .75 1.06 .69 .31 2.94 1.69
5/16 1016037 1,250 .39 1.63 .81 1.00 1.25 .81 .38 3.56 2.06
3/8 1016055 2,250 .71 2.00 .94 1.25 1.50 1.00 .50 4.31 2.50
Securement
1/2 1016073 3,600 1.32 2.50 1.31 1.50 2.00 1.31 .63 5.44 3.19
Load
5/8 1016091 5,200 2.49 3.00 1.56 1.75 2.38 1.50 .75 6.56 3.88
3/4 1016117 7,200 4.02 3.50 1.75 2.00 2.63 1.88 .88 7.19 4.31
7/8 1016135 10,000 6.25 4.00 2.06 2.25 3.06 2.13 1.00 8.38 5.00
1 1016135 12,500 8.95 4.50 2.31 2.50 3.50 2.38 1.13 9.63 5.75
Contractors
1-1/4 1016199 18,000 16.37 5.63 2.69 3.13 3.69 3.00 1.50 11.44 6.75
Supply
1-1/2 1016215 45,200 45.79 7.09 3.88 4.09 3.88 3.75 2.25 16.69 9.91

Protection
Fall

403

G-403 Jaw End Swivels
G-403 Jaw End Swivels meet the performance
requirements of Federal Specification RR-C-271F,
Type VII, Class 3, except for those provisions required
of the contractor.
U.S. Patent 5,381,650 and other equivalents.
■ Hot Dip Galvanized

■ Quenched & Tempered
■ Crosby products meet or exceed all requirements
of ASME B30.26, including identification, ductility,
design factor, proof load and temperature requirements.
Importantly, Crosby products meet other critical
performance requirements, including fatigue life, impact
properties and material traceability, not addressed by
ASME B30.26.
■ 401, 402 and 403 swivels are positioning devices and
are not intended to rotate under load. Use in corrosive
environment requires shank and nut inspection in
accordance with ASME B30.10-1.10.4(b)(5)(c)2009.
G-403 Jaw End Swivel

Working
Size Load
No. Each (in.)
Limit
in. G-403 lbs. * lbs. A B C G K M N P R U V
1/4 1016395 850 .21 1.25 .69 .75 .69 .47 .31 .88 .25 2.63 1.69 1.69
5/16 1016411 1,250 .34 1.63 .81 1.00 .81 .50 .38 .88 .31 2.94 2.06 1.81
3/8 1016439 2,250 .66 2.00 .94 1.25 1.00 .63 .50 1.06 .38 3.63 2.50 2.25
1/2 1016457 3,600 1.34 2.50 1.31 1.50 1.31 .75 .63 1.31 .50 4.50 3.19 2.88
5/8 1016475 5,200 2.48 3.00 1.56 1.75 1.63 .94 .75 1.50 .63 5.31 3.88 3.44
3/4 1016493 7,200 3.88 3.50 1.75 2.00 1.88 1.13 .88 1.75 .75 6.06 4.31 4.00
7/8 1016518 10,000 5.87 4.00 2.06 2.25 2.13 1.19 1.00 2.06 .88 7.00 5.00 4.53
1 1016536 12,500 9.84 4.50 2.31 2.50 2.63 1.75 1.13 2.81 1.13 8.56 5.75 5.94
1-1/4 1016572 18,000 15.75 5.69 2.69 3.13 3.13 2.06 1.50 2.81 1.38 9.75 7.06 6.38
1-1/2 1016590 45,200 54.75 7.00 3.88 4.09 5.63 2.88 2.25 4.44 2.25 14.25 10.00 10.84
404

Swivels
Cranes / Jibs
Overhead
With Tapered Roller Thrust Bearing
■ Suitable for frequent rotation under load.
■ All swivels individually proof tested with certification.
■ All hooks furnished with latches assembled.
Hoists
■ All jaws complete with bolts, nuts and cotter pins.
■ Pressure lube fitting provided.
■ NOT TO BE USED ON DEMOLITION (WRECKING) BALLS.
■ Other types and capacities up to 1250t, available to meet
your requirements.
Services
■ IMPORTANT - Crosby Swivels should only be used with the
recommended wire rope. Contact the wire rope manufacturer
for the proper wire rope to be used with Crosby Swivels.
Engineered
S-1 Jaw & Hook
Products
Wire
S-1 Weight
Swivel WLL Rope Dimensions (in.)
Stock Each
No. (t) * Size
No. (lbs.)
(in.) A F G H J K L M N O P V
3-S-1 297011 3 1/2 9.81 11.44 4.84 2.75 0.75 0.88 1.62 1.53 1.41 1.31 1.00 1.44 1.12
Slings
5-S-1 297217 5 5/8 15.51 13.34 6.28 3.00 0.88 1.00 2.25 1.94 1.69 1.62 1.12 1.81 1.44
8-S-1 297413 8-1/2 3/4 29.42 16.45 7.54 4.00 1.00 1.56 2.81 2.46 2.22 2.12 1.38 2.25 1.62
10-S-1 297618 10 7/8 46.75 19.75 8.34 4.50 1.50 1.75 3.38 2.59 2.41 3.50 1.75 2.59 1.94
15-S-1 297814 15 1 73.75 22.24 10.34 5.00 1.50 1.75 3.38 2.81 3.19 3.50 1.75 3.00 2.38
25-S-1 298118 25 – 140 26.78 13.62 6.00 2.00 2.00 4.62 3.44 3.62 3.69 2.38 3.66 3.00
35-S-1 298216 35 – 220 29.94 14.06 6.50 2.00 2.00 4.62 3.88 3.75 3.69 2.38 4.56 3.19
Hardware
45-S-1 298314 45 – 251 35.06 15.44 7.00 2.25 2.50 5.00 4.75 4.25 4.00 3.00 5.06 3.25
* Individually Proof Tested to 2 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
S-2 Jaw & Jaw

Wire
S-2 Weight Dimensions
Products
Swivel WLL Rope
Lifting
Stock Each (in.)
No. (t) * Size
No. (lbs.)
(in.) B G H J K N O
3-S-2 297020 3 1/2 9.63 9.28 2.75 0.75 0.88 1.62 1.31 1.00
5-S-2 297226 5 5/8 13.69 10.31 3.00 0.88 1.00 2.25 1.62 1.12
8-S-2 297422 8-1/2 3/4 26.16 12.62 4.00 1.00 1.56 2.81 2.12 1.38
10-S-2 297627 10 7/8 45.75 16.75 4.50 1.50 1.75 3.38 3.50 1.75
Rope
Wire
15-S-2 297823 15 1 62.75 17.12 5.00 1.50 1.75 3.38 3.50 1.75
25-S-2 298127 25 – 140 20.75 6.00 2.00 2.00 4.62 3.69 2.38
35-S-2 298225 35 – 155 20.75 6.50 2.00 2.00 4.62 3.69 2.38
45-S-2 298323 45 – 235 25.25 7.00 2.25 2.50 5.00 4.00 3.00
Cordage
S-3 Jaw & Eye
Wire
Swivel WLL Rope
Stock Each (in.)
No. (t) * Size
Securement
No. (lbs.)
(in.) C G H J K N O Q R S T
Load
3-S-3 297039 3 1/2 9.12 9.34 2.75 0.75 0.88 1.62 1.31 1.00 0.75 1.03 1.12 1.25
5-S-3 297235 5 5/8 13.50 10.06 3.00 0.88 1.00 2.25 1.62 1.12 1.00 1.28 1.25 1.25
8-S-3 297431 8-1/2 3/4 24.90 12.25 4.00 1.00 1.56 2.81 2.12 1.38 1.25 1.41 1.62 1.50
10-S-3 297636 10 7/8 43.50 16.12 4.50 1.50 1.75 3.38 3.50 1.75 1.69 1.69 2.75 1.88
15-S-3 297832 15 1 61 16.75 5.00 1.50 1.75 3.38 3.50 1.75 1.94 2.03 2.75 2.12
Contractors
25-S-3 298136 25 – 135 21.50 6.00 2.00 2.00 4.62 3.69 2.38 2.25 2.31 3.88 2.38
Supply
35-S-3 298234 35 – 150 21.50 6.50 2.00 2.00 4.62 3.69 2.38 2.25 2.31 3.88 2.38
45-S-3 298332 45 – 225 25.88 7.00 2.25 2.50 5.00 4.00 3.00 2.50 2.53 4.00 3.00
Protection
Fall

405

Swivels (Continued)
With Tapered Roller Thrust Bearing
S-4 Eye & Jaw

Wire
S-4 Weight
Swivel WLL Rope Dimensions (in.)
Stock Each
No. (t) * Size
No. (lbs.)
(in.) C G H J K N O Q R S T
3-S-4 297048 3 1/2 9 9.34 2.75 0.75 0.88 1.62 1.31 1.00 0.75 1.03 1.12 1.25
5-S-4 297244 5 5/8 12.33 10.06 3.00 0.88 1.00 2.25 1.62 1.12 1.00 1.28 1.25 1.25
8-S-4 297440 8-1/2 3/4 29 12.25 4.00 1.00 1.56 2.81 2.12 1.38 1.25 1.41 1.62 1.50
10-S-4 297645 10 7/8 44 16.12 4.50 1.50 1.75 3.38 3.50 1.75 1.69 1.69 2.75 1.88
15-S-4 297841 15 1 61 16.75 5.00 1.50 1.75 3.38 3.50 1.75 1.94 2.03 2.75 2.12
25-S-4 298145 25 – 135 21.50 6.00 2.00 2.00 4.62 3.69 2.38 2.25 2.31 3.88 2.38
35-S-4 298243 35 – 150 21.50 6.50 2.00 2.00 4.62 3.69 2.38 2.25 2.31 3.88 2.38
45-S-4 298341 45 – 225 25.88 7.00 2.25 2.50 5.00 4.00 3.00 2.50 2.53 4.00 3.00
S-5 Eye & Eye

Wire
Swivel WLL Rope
Stock Each (in.)
No. (t) * Size
No. (lbs.)
(in.) D G Q R S T
3-S-5 297057 3 1/2 8.5 9.41 2.75 0.75 1.03 1.12 1.25
5-S-5 297253 5 5/8 11.3 9.81 3.00 1.00 1.28 1.25 1.25
8-S-5 297459 8-1/2 3/4 29.25 11.88 4.00 1.25 1.41 1.62 1.50
10-S-5 297654 10 7/8 42 15.50 4.50 1.69 1.69 2.75 1.88
15-S-5 297850 15 1 49 16.38 5.00 1.94 2.03 2.75 2.12
25-S-5 298154 25 – 130 22.25 6.00 2.25 2.31 3.88 2.38
35-S-5 298252 35 – 145 22.25 6.50 2.25 2.31 3.88 2.38
45-S-5 298350 45 – 215 26.50 7.00 2.50 2.53 4.00 3.00
S-6 Eye & Hook

Wire Dimensions
S-6 Weight
Swivel WLL Rope (in.)
Stock Each
No. (t) * Size
No. (lbs.) E F G L M P Q R S T V
(in.)
3-S-6 297066 3 1/2 9.32 11.50 4.84 2.75 1.53 1.41 1.44 0.75 1.03 1.12 1.25 1.12
5-S-6 297262 5 5/8 14.24 13.09 6.28 3.00 1.94 1.69 1.81 1.00 1.28 1.25 1.25 1.44
8-S-6 297468 8-1/2 3/4 32 16.07 7.54 4.00 2.46 2.22 2.25 1.25 1.41 1.62 1.50 1.62
10-S-6 297663 10 7/8 45.5 19.12 8.34 4.50 2.59 2.41 2.59 1.69 1.69 2.75 1.88 1.94
15-S-6 297869 15 1 63 21.24 10.34 5.00 2.81 3.19 3.00 1.94 2.03 2.75 2.12 2.38
25-S-6 298163 25 – 135 27.53 13.62 6.00 3.44 3.62 3.66 2.25 2.31 3.88 2.38 3.00
35-S-6 298261 35 – 215 30.69 14.06 6.50 3.88 3.75 4.56 2.25 2.31 3.88 2.38 3.19
45-S-6 298369 45 – 270 35.69 15.44 7.00 4.75 4.25 5.06 2.50 2.53 4.00 3.00 3.25
406

Angular Contact Ball
Cranes / Jibs
Overhead
Bearing Swivels
Streamlined Design
and Maximum Performance
Hoists
■ Designed for high rotational speeds, these models
react to low operational torque…the perfect swivels
for longer ropes and cables.
■ Manufactured with two or more flush ground angular
Services
contact ball bearings.
■ Bearings are permanently lubricated with high-pressure
grease and sealed at the factory.
■ Flush pins are available for overhead and
Engineered
underground electrical line stringing
Products
(please specify). Swivel ends are shaped to prevent
snagging when gliding over sheaves and other
Model 60 Model 61 Model 62 Model 63
potential obstructions.
■ Heat treated high strength alloy steel, zinc plated for
corrosion resistance, provides the strongest yet lightest
Slings
swivel available. Ultimate strength is minimum 4.5 to 1
over SWL (Safe Working Load).
■ All swivels proof-tested and certified.
Hardware
Model 64 Model 65 Model 66 Model 67
Products
Lifting
Wire C J
SWL
Size Rope A Pin D E F G H I Hole K
Tons
Size Dia. Dia.
12 .5 (.9) 1/8 7/8 5/16 5/16 1/4 15/32 7/8 3/8 3/8 1/4 3/8
Rope
Wire
25 .75 (2) 1/4 1-1/4 3/8 19/32 5/16 11/16 31/32 1/2 7/16 3/8 7/16
37 1.5 (4) 3/8 1-1/2 7/16 19/32 1/2 13/16 1 23/32 9/16 5/8 5/8
50 3 (5) 1/2 1-7/8 5/8 3/4 3/4 15/16 1-11/32 15/16 13/16 7/8 15/16
62 5 (8) 5/8 2-7/16 7/8 1 1 1-9/16 1-11/16 1-5/16 1-1/8 1-1/4 1-3/16
Cordage
75 8.5 (15) 3/4 2-7/8 1 1-9/32 1-1/4 2-1/8 2-1/4 1-5/8 1-1/4 1-3/8 1-1/2
81 8.5 (15) 3/4 2-7/8 1-1/8 1-9/16 1-1/4 2-1/8 2-1/4 1-5/8 1-1/4 1-3/8 1-1/2
87 10 (17) 7/8 3-5/8 1-1/2 1-3/4 1-23/32 3-1/2 3 2-27/32 1-3/4 1-5/8 1-13/16
99 15 (20) 1 3-5/8 1-1/2 1-3/4 2 3-1/2 3 2-25/32 1-3/4 2 2-1/8
150 35 1-1/2 5-3/8 2 2 2-1/4 3-11/16 3-3/4 3-1/8 2-3/8 2-1/4 2-3/8
Securement
Load
All dimensions in inches

( ) For line stringing applications requiring a 3 to 1 Safe Working Load.
Contractors
Supply
Protection
Fall

407

Hooks WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Sliding Choker Hooks—

Quenched & Tempered
Forged Alloy Steel through 3/4”.
Wide throat to take heavy thimbles.
* When ordering, eye diameter “C”
should be specified.
Single Eight Safe

Working Dimensions (in.) Weight
Part Part
Load Pounds
Rope Rope
Each
Size Size lbs. A C E L
3/8 n/a 2500 2.06 .63 .63 4.28 .77
1/2 1/8 3300 2.25 .75 .78 4.97 1.19
* 5/8 3/16 5000 3.06 .75 .94 6.38 2.89
* 5/8 3/16 5000 3.06 1 .94 6.38 2.70
* 3/4 1/4 8000 3.38 1 1.16 7.66 2.95
* 3/4 1/4 8000 3.38 1.44 1.16 7.66 5.00
Snap Hooks—Forged Steel, Replacement Hooks—

Quenched & Tempered Quenched & Tempered
Pressed steel latches and stainless Easily attached to any chain and
steel springs, bolts and nuts. electric hoist with welded link load chain,
roller chain or wire rope with suitable
end fitting. Swivel jaw is forged.
Safe Inside Width

Hook Throat Length Weight Size Dia. Overall Throat Weight
Working Dia. Between
Size Opening Overall Pounds Hoist Bolt Length Opening Pounds
Load of Eye Jaws
Each Each
in. lbs. in. in. in. tons in. in. in. in.
7/16 750 3/4 3/4 3-15/16 .23 1/2 9/16 3/8 6-1/8 31/32 1.25
9/16 1000 1-1/8 13/16 4-3/4 .48 1 11/16 7/16 7-11/16 1-18 2.61
Sorting Hooks— Barrel Hooks—

Forged Alloy Steel, Forge Carbon Steel
Quenched & Tempered
Deep straight throat permits efficient
handling of flat plates or large cylindrical
shapes. The long tapered point allows
easy grab in rings, pear links, eye bolts
or lifting holes.
Safe Working Load at Tip 2 Ton I.D. of Eye 1-9/16"

Safe Working Load at Bottom of Hook 7-1/2 Ton O.D. of Eye 2-13/16"
Overall Length 9-11/16" Overall Length 5"
I.D. of Eye 1-3/8" Width of Lip 2-7/8"
Opening at Top of Hook 2-13/16" Weight Per Pair (pounds) 3-1/4
Radius at Bottom of Hook 5/8" Safe Working Load 1 Ton
Weight Pounds Each 6.25
408

H-323 / A-323
Cranes / Jibs
Overhead
Eye Grab Hooks
■ Forged Steel - Quenched and Tempered.
■ Design Factor is 4:1.
■ H-323 designed for Crosby Spectrum 4® chain.
Hoists
■ A-323 designed for Crosby Spectrum 7® chain.
Services
Stock Working Load Dimensions
Chain Weight
Engineered
No. Limit (lbs.) (in.)
Products
Size Each
(in.) H-323 A-323 (lbs.)
H-323 A-323 A B C D E G K L N R
Carbon Alloy *
1/4 1026204 1026384 * 2600 3500 .28 1.09 .53 .31 1.81 .34 .88 .47 3.05 1.75 1.88
5/16 1026222 1026400 * 3900 4700 .45 1.31 .62 .38 2.12 .44 .97 .59 3.59 2.06 2.28
3/8 1026240 1026428 * 5400 7100 .79 1.56 .75 .44 2.53 .50 1.17 .72 4.28 2.34 2.69
Slings
1/2 1026286 1026464 * 9200 12000 1.75 1.94 .88 .53 3.56 .66 1.53 .78 5.44 2.97 3.38
5/8 1026302 1026482 * 13000 18100 3.25 2.38 1.06 .66 4.41 .78 1.89 1.00 6.66 3.78 4.11
3/4 1026320 1026507 20200 24700 5.94 2.88 1.38 .75 5.22 .94 2.13 1.31 8.06 5.09 5.16
* These A-330 hooks are forged with an “8” designating Grade 80, and are suitable for use with Grade 8 chain in over head lifting applications
Hardware
as long as hook is proof-tested as part of the chain sling assembly or as an individual component per ASME B30.9. We recommend the use of
the A-338 which is proof tested and supplied with a proof test certificate.
H-330 / A-330
Products
Clevis Grab Hooks
Lifting
■ Forged Steel - Quenched and Tempered.
■ Design factor is 4:1.
■ Features quick and easy assembly.
Rope
Wire
■ H-330 designed for Crosby Spectrum 4® chain.
■ A-330 designed for Crosby Spectrum 7® chain.

Chain No. Limit (lbs.) Weight (in.)
Cordage
Size Each
(in.) H-330 A-330 (lbs.)
H-330 A-330 A B C D E G H K L N P R
Carbon Alloy *
1/4 1027105 1027249 * 2600 3500 .36 1.00 .32 .31 1.81 .34 .88 .72 .47 3.05 1.75 .31 1.64
5/16 1027123 1027267 * 3900 4700 .62 1.22 .43 .36 2.12 .44 .97 .91 .59 3.66 2.06 .38 2.02
Securement
3/8 1027141 1027285 * 5400 7100 1.00 1.42 .48 .49 2.53 .50 1.17 1.00 .72 4.42 2.34 .44 2.41
Load
7/16 1027169 1027301 7200 8750 1.31 1.66 .66 .62 3.09 .56 1.31 1.13 .69 4.94 2.66 .56 2.75
1/2 1027187 1027329 * 9200 12000 2.22 1.88 .57 .51 3.56 .66 1.53 1.25 .78 5.72 2.97 .63 3.19
5/8 1027203 1027347 13000 18100 4.41 2.31 .71 .67 4.39 .78 1.78 1.56 1.09 6.83 4.31 .75 4.09
3/4 1027221 1027365 20200 24700 6.50 2.62 .94 .94 5.22 .94 2.13 1.88 1.31 8.13 5.09 .88 4.63
Contractors
Supply
* These A-330 hooks are forged with an “8” designating Grade 80, and are suitable for use with Grade 8 chain in over head lifting applications
as long as hook is proof-tested as part of the chain sling assembly or as an individual component per ASME B30.9. We recommend the use of
the A-338 which is proof tested and supplied with a proof test certificate.
Protection
Fall

409

H-324
Eye Slip Hooks
■ Forged Carbon Steel – Quenched and Tempered.
■ Not Suitable for use with Grade 80 chain and chain
slings used in overhead lifting. For slings or lifting
chains, Grade 80 or 100 alloy components are
recommended.
Stock Working Dimensions

Chain Weight
No. Load (in.)
Size Each
Limit
(in.) (lbs.)
(lbs.)
H-324 A B C D E F G H K L N R
1/4 1026749 1950 .40 1.06 .50 .28 2.75 .94 1.19 .81 .88 .50 3.66 2.13 2.56
5/16 1026767 2875 .64 1.25 .63 .34 3.06 1.06 1.25 .94 1.00 .56 4.23 2.25 2.95
3/8 1026785 4000 1.10 1.53 .72 .41 3.63 1.31 1.50 1.13 1.19 .66 4.89 2.56 3.36
7/16 1026801 5000 1.56 1.69 .81 .44 4.34 1.56 1.81 1.38 1.44 .81 5.70 3.06 3.88
1/2 1026829 6500 2.09 1.94 .94 .50 4.81 1.69 1.94 1.56 1.63 .91 6.34 3.44 4.28
5/8 1026847 9250 3.90 2.38 1.13 .63 5.63 2.00 2.38 1.81 1.94 1.09 7.66 4.00 5.22
3/4 1026865 12500 6.93 2.88 1.38 .75 6.75 2.13 2.75 2.19 2.31 1.31 8.73 4.75 5.80
H-331 / A-331
Clevis Slip Hooks
■ Forged Carbon Steel or Forged Alloy Steel –
Quenched and Tempered.
■ All pins are Alloy Steel – Quenched and Tempered.
■ Not Suitable for use with Grade 80 chain and chain
slings used in overhead lifting. For slings or lifting
chains, Grade 80 or 100 alloy components are
recommended.

Chain No. Limit (lbs.) Weight (in.)
Size Each
(in.) H-331 A-331 (lbs.)
H-331 A-331 A B C D E F G H K L N P R T
Carbon Alloy *
1/4 1027383 1027524 1950 2750 .55 1.06 .32 .29 2.75 .94 1.19 .81 .88 .50 3.95 2.13 .31 2.58 .81
5/16 1027409 1027542 2875 4300 .79 1.22 .43 .34 3.06 1.06 1.25 .94 1.00 .56 4.52 2.25 .38 2.87 .97
3/8 1027427 1027560 4000 5250 1.21 1.38 .45 .44 3.63 1.31 1.50 1.13 1.19 .66 5.15 2.56 .44 3.25 1.06
7/16 1027445 1027588 5000 7000 2.06 1.73 .59 .60 4.34 1.56 1.81 1.38 1.44 .81 5.97 3.06 .56 3.70 1.19
1/2 1027463 1027604 6500 9000 2.75 1.88 .57 .53 4.81 1.69 1.94 1.56 1.63 .91 6.53 3.44 .63 4.00 1.31
5/8 1027481 1027622 9250 13500 4.75 2.31 .71 .71 5.63 2.00 2.38 1.81 1.94 1.09 7.89 4.00 .75 4.94 1.56
3/4 – 1027640 – 19250 11.28 3.19 1.18 1.29 7.38 2.50 3.00 2.38 2.50 1.44 10.02 5.06 1.00 6.09 2.09
410

Golden Gate® Hooks WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Gate Types
Brass alloy Golden Gates® are engineered for quality,

easy handling and dependability. The heavy-duty, corrosion
Hoists
resistant locking mechanism will stay locked until an
operator releases it; yet, can easily be shut with one hand.
Cost effective, these gates reduce down time, providing
the alternative to conventional latches.
Services
LIF-LOK®
LIF-LOK GATE—Size 1
®
To lock: close the gate; the built-in spring locks the

gate against the hook tip.
Engineered
Products
To unlock: lift the gate upward on the hook shank
and swing open.
PIN-LOK®—Sizes 2 through 4
Slings
To lock: close the gate; a stainless steel pin is
carried in a horizontal bore and engages a milled slot
PIN-LOK®
in the hook shank.
Hardware
To unlock: simply depress the stainless steel pin which
causes the pin to disengage from the milled slot.
ROLLOX® GATE—Sizes 5 through 9
Products
Lifting
To lock: close the gate; a stainless steel pin is mounted
in a horizontal bore which passes through the gate and
engages a notch milled in the hook shank.
To unlock: move the lever downward a quarter-turn or
until it stops, the gate can now swing open 160° (approx.). ROLLOX®
Rope
Wire
TIP-LOK® GATE—Sizes 10 through 17
To lock: press the arm down until the lock trips;
Cordage
two arms of the gate now enclose the tip of the hook.
To unlock: manually depressing the locking trigger
automatically raises the movable arm, allowing the gate
Securement
to be rotated open.
Load
TIP-LOK®
Contractors
Supply
Protection
Fall

411

Golden Gate® Hooks WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
(Continued)
Hook Connectors
The six connector styles shown to the right make it
possible for Crosby to furnish a Golden Gate Hook to fit
almost any make or model of hoisting equipment.
Each connector is available with either a self-closing or

manual closing gate. (e.g.: A size 4 hook with a closed swivel
bail connector and self-closing gate is 4-C; with manual
closing gate, it is 4-A.)
Closed Swivel Bail—For use where hoisting line

or shackle can be inserted into the bail.
■ Hook sizes: 1 through 14
■ Style C—with self-closing gate.
■ Style A—with manual-closing gate.
Closed Swivel Bail Shank Type Hook
Shank Type Hook (standard length)—For use on
existing load blocks, with standard shank length.
Shank Type Hook (long length)—For use on existing

blocks requiring extra shank length.
Universal Type—Open swivel bail for attachment

to link chain.
■ Hook sizes: 3, 4 and 5
■ Style E—with self-closing gate.
Shank Type Hook Universal Type
■ Style G—with manual-closing gate.
Link Chain Nest—With ball-bearing swivel; attaches to

chain by an alloy pin.
■ Style O—with self-closing gate.
■ Style P—with manual-closing gate.
Roller Chain Nest—Attached with ball-bearing swivel

and full-floating connector.
■ Style S—with self-closing gate.
■ Style R—with manual-closing gate.
Link Chain Nest Roller Chain Nest
412

Hook Data Form
Cranes / Jibs
Overhead
Hook Size:
Sales Order:
Working Load Limit (Tons):
Hoists
Hoist Name & Model:
Top Hook and/or Bottom Hook:
Is Self-Closing Gate Required:
Name of Person Completing
Services
Form:
Phone:
Distributor:
Engineered
Products
Distributor P.O.:
Accurate dimensions are important.
Shank Length
Slings
1. Measure total USABLE shank length from top of hook
shank to top of of gate assembly. Gate assembly is
not considered part of the USABLE SHANK. When
measuring other manufacturer's hooks, measure from
Hardware
the top of the hook shank to the hook shoulder.
2. Measure threaded portion (enter BLANK if threads
not required).
Note: Hook is supplied with Steel Hex-Load Nut
Products
and Bronze Load Washer. Hook and Nut threads
Lifting
are National Coarse. If a SPECIAL Load Nut or Load
Washer is required, attach a drawing to this form.
Shank Diameter
Rope
Wire
3. Measure width of threaded portion.
4. Measure width of blank portion.
Throat Opening
Cordage
5. ONLY measure throat opening if this distance is
critical to customer's operation.
Cross Hole in Shank Hooks

Securement
(complete only if required)

Load
6. Measure shank length from center of hole to top

of gate assembly.
7. Measure diameter of hole.
Contractors
Supply
Protection
Fall

413

Weld-On WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Excavator Hooks
■ The original weld-on hook from Gunnebo Lifting
■ Each hook is furnished with welding and
loading instructions
■ Replacement latch and latch springs available.
■ Full traceability for each component
Working Dimensions Weight

Model Load Limit (in.) Each
(tons) * B C G H K L S A (lbs.)
UKN-0.75 ** .75 .79 2.2 .51 .79 .75 3.2 .20 .12 .66
UKN-1 ** 1 .79 2.8 .67 .99 .99 3.7 .24 .16 1.3
UKN-2 ** 2 1 3.4 .79 1.2 1.2 4.5 .31 .20 2.2
UKN-3 3 1.2 4.1 .91 1.3 1.4 5.2 .39 .24 2.2
UKN-4 4 1.1 4.5 1.1 1.5 1.7 5.5 .43 .28 2.9
UKN-5 5 1.3 5.2 1.2 1.9 1.8 6.5 .47 .32 6.4
UKN-8 8 1.3 5.2 1.5 2 2 6.8 .51 .35 7.7
UKN-10 10 1.9 6.7 1.7 2.3 2.2 8.7 .55 .35 14.1
UKN-15 15 2.1 7.4 2.0 2.6 2.4 9.4 .59 .47 19.4
* Design Factor 5:1 proof tested and certified ** Welding plate on UKN-0.75, UKN-2, and UKN-1 is slightly curved.
For welding use Electrode AWS A 5.1 E 7018
Eye Type
Self-Locking Hooks
■ The Original Self-Locking Hook
■ Latch closes automatically under load.
■ Hook will not open when under load.
■ Oversized eye allows attachment to either chain or
wire rope slings
■ Stainless steel spring release trigger will only operate
when hook is unloaded
■ Full traceability
■ Proof tested to 2-1/2 times working load limit
Chain Working Weight

Dimensions (in.)
Model Size Load Limit Each
(in.) (lbs.) * L B E F G H (lbs.)
BK-6-10 7/32 2,700 4.3 1.1 .87 .39 .59 .83 1.1
BK-7/8-10 9/32 4,300 5.4 1.5 1.1 .43 .67 1 2
BK-7/8-10 5/16 5,700 5.4 1.5 1.1 .43 .67 1 2
BK-10-10 3/8 8,800 6.6 1.7 1.3 .51 .83 1.2 3.3
BK-13-10 1/2 15,000 8.1 2.1 1.7 .63 1.2 1.5 6.2
BK-16-10 5/8 22,600 10 2.4 2.2 .79 1.5 1.9 12.3
BK-18/20-10 3/4 35,300 11.4 2.7 2.4 .87 1.7 2.5 18.3
BK-22-8 7/8 34,200 12.6 3.1 2.8 .95 1.9 2.4 24.7
BK-26-8 1 47,700 13.6 3.9 3.1 1 2 2.7 32
BK-28-8 1-1/8 55,100 15.7 4.7 3.5 1.1 2.4 3.2 48.5
* Design Factor 4:1 Proof tested and certified. ** Grade 100 hooks have recessed trigger
414

Swivel Bronze Bushing WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Self-Locking Hooks
■ Swivels on a bushing to position hook before loading
■ Latch closes automatically under load.
■ Hook will not open when under load.
Hoists
■ Full traceability
■ Proof tested to 2-1/2 times working load limit
■ Stainless steel spring release trigger will only operate
when hook is unloaded
Services
Engineered
Products
Chain Working Dimensions Weight
Model Size Grade Load Limit (in.) Each
(in.) (lbs.) * L B C E F G H (lbs.)
BKL-6-10 7/32 100 2,700 5.9 1.1 .90 1.3 .43 .59 .83 1.5
BKL-7/8-10 9/32 100 4,300 7.2 1.5 1.1 1.5 .47 .67 1 2.6
Slings
BKL-7/8-10 5/16 100 5,700 7.2 1.5 1.1 1.5 .47 .67 1 2.6
BKL-10-10 3/8 100 8,800 8.6 1.7 1.4 1.7 .59 .83 1.2 4.4
3-106-8 1/2 100 15,000 11 2.1 1.9 1.9 .75 1.2 1.5 8.4
BKL-16-10 5/8 100 22,600 13.5 2.4 2.6 2.4 .87 1.5 1.9 15.6
BKL-18/20-10 3/4 100 35,300 14.4 2.7 2.8 2.9 1 1.7 2.5 24.5
Hardware
* Design factor 4:1 Proof tested and certified.
Grade 100 hooks have recessed trigger. Hook can not be rotated when under a load
WARNING SEE warning

See WARNING and
INFORMATION
application
Products
S-265 Weld-On Pivot Link
Lifting
information
ON PAGES 454
on page
- 461.?.
■ Forged Steel — Quenched and Tempered.

■ Forged from 1035 Carbon Steel.
■ Excellent welding qualities.
Rope
Wire
■ Reference American Welding Society specifications
for proper welding procedures.
Cordage
Securement
Working Load Limit (t) Dimensions (in.) Minimum

Stock No. Weight
Load
Design Design Fillet

S-265 Eeach
Factor Factor A B C D F G H Weld Size
(lbs.)
5:1 4:1 (in.)
1 1.2 1290740 .88 1.57 1.42 3.27 1.38 .51 2.60 1.65 3/32
Contractors
2.5 3.2 1290768 1.32 1.77 1.73 3.90 1.65 .71 3.19 1.89 3/32
Supply
4.2 5.3 1290786 2.65 2.17 1.97 4.84 1.93 .87 3.90 2.24 1/4
6.4 8 1290802 5.29 2.76 2.52 5.67 2.52 1.02 4.80 2.64 1/4
12 15 1290820 13.01 3.82 3.54 7.60 3.39 1.34 6.50 3.70 5/16
Protection
Fall

415

S-319 / S-319N WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Shank Hooks
Patented trademark indicates QUIC-CHECK® product.
Hook Material Codes: A-Alloy Steel, B-Bronze High
Strength, C-Carbon Steel.
■ The most complete line of shank hoist hooks.

Available 3/4 to 300 metric tons.
■ Hook Identification code forged into each hook.
■ Quenched and Tempered.
■ Available in carbon steel, alloy steel and bronze.
■ Proper design, careful forging, and precision
controlled quench and tempering give maximum
strength without excessive weight and bulk.
■ Every Crosby Shank Hook has a pre-drilled cam,
which can be equipped with a latch. Simply purchase
the latch assemblies. Even years after
purchase of the original hook, latch assemblies
can be added.
■ Type Approval and certification in accordance Shank hook dimensions
with PL Latch Assembled
with ABS 2006 Steel Vessel Rules 1-1-17.7, and
ABS Guide for Certification of Cranes.
■ Patented McKissick Split-Nut retention system available.
Working Load Limit Hook Dimensions

Weight
(tons) Identification (in.)
(lbs.)
Carbon Alloy Bronze 319C 319A 319B D F G H J K L M O P R T X ** Y Z
3/4 1 .5 DC DA DB 2.86 1.25 .73 .81 .93 .63 5.14 .63 * .93 1.96 2.35 .97 .59 2.06 .69 .50
1 1-1/2 .6 FC FA FB 3.16 1.38 .84 .94 .97 .71 5.68 .71 * .97 2.22 2.59 .97 .66 2.25 .78 .75
1-1/2 2 1 GC GA GB 3.59 1.50 1.00 1.16 1.06 .88 6.35 .88 * 1.06 2.44 2.76 1.03 .72 2.59 .88 1
2 3 1.4 HC HA HB 4.00 1.62 1.14 1.31 1.19 .94 7.14 .94 * 1.16 2.78 3.16 1.16 .88 2.84 1.00 1.82
3 5 2 IC IA IB 4.84 2.00 1.44 1.63 1.50 1.31 8.63 1.13 * 1.41 3.47 3.85 1.53 1.16 3.34 1.25 3.69
5 7 3-1/2 JC JA JB 6.28 2.50 1.82 2.06 1.78 1.66 10.43 1.44 * 1.69 4.59 4.77 1.94 1.41 3.84 1.56 7.25
7-1/2 11 5 KC KA KB 7.54 3.00 2.26 2.63 2.41 1.88 12.52 1.63 * 2.22 5.25 5.88 2.46 1.81 4.38 1.94 13.49
10 15 6-1/2 LC LA LB 8.34 3.25 2.60 2.94 2.62 2.19 13.47 1.94 * 2.22 5.96 6.37 2.59 2.00 4.50 2.19 18
15 22 10 NC NA NB 10.34 4.25 3.01 3.50 3.41 2.69 16.65 2.38 * 2.41 6.88 8.14 2.81 2.56 5.50 2.63 35.33
20 30 – OC OA – 13.62 5.00 3.62 4.62 4.00 3.00 23.09 – * 3.19 8.78 9.44 3.44 3.12 10.00 3.12 72
20 30 – OC OA – 13.62 5.00 3.62 4.62 4.00 3.00 31.09 – 3.25 8.78 9.44 3.44 3.12 18.00 3.12 85.50
25 37 – PC PA – 14.06 5.38 4.56 5.00 4.25 3.62 32.12 – 3.25 11.38 12.56 3.88 4.00 15.00 4.00 134
25 37 – PC PA – 14.06 5.38 4.56 5.00 4.25 3.62 41.12 – 3.00 11.38 12.56 3.88 4.00 24.00 4.00 172
30 45 – SC SA – 15.44 6.00 5.06 5.50 4.75 3.72 34.12 – 3.00 12.63 14.00 4.75 4.00 15.00 4.00 182
30 45 – SC SA – 15.44 6.00 5.06 5.50 4.75 3.72 43.12 – 3.38 12.63 14.00 4.75 4.00 24.00 4.00 214
40 60 – TC TA – 18.50 7.00 6.00 6.50 5.75 4.44 36.06 – 3.38 14.81 15.50 5.69 4.50 14.50 4.50 268
40 60 – TC TA – 18.50 7.00 6.00 6.50 5.75 4.44 47.56 – 4.12 14.81 15.50 5.69 4.50 26.00 4.50 312
50 75 – UC UA – 20.62 7.75 6.69 7.25 6.50 4.81 41.16 – 4.12 16.53 19.38 6.00 5.00 15.00 5.00 390
50 75 – – UA – 20.62 7.75 6.69 7.25 6.50 4.81 49.16 – 5.38 16.53 19.38 6.00 5.00 23.00 5.00 426
– 100 – – WA – 23.00 6.81 8.59 9.88 5.88 5.50 42.12 – 5.38 17.38 18.41 7.00 7.00 15.00 7.00 610
– 100 – – WA – 23.00 6.81 8.59 9.88 5.88 5.50 48.12 – 4.50 17.38 18.41 7.00 7.00 21.00 7.00 675
– 150 – – XA – 24.38 6.75 9.12 10.94 6.00 6.00 45.75 – 4.50 18.00 18.38 7.00 7.25 18.00 7.25 735
– 200 – – YA – 26.69 7.50 9.75 11.81 6.60 7.00 50.50 – 5.00 19.25 20.50 8.00 8.00 20.00 8.00 1020
– 300 – – ZA – 30.12 9.50 10.62 12.94 8.00 7.25 54.69 – 6.25 22.69 20.50 8.25 9.50 20.00 9.50 1390
* Dimensions shown are for S-4320 Latch kits. Dimensions for sizes 20 ton carbon and larger are for PL Latch Kits.
** Dimension before machining (as forged).
Note: Proof load is 2 times Working Load Limit. All carbon hooks—average straightening load (ultimate load) is 5 times Working Load Limit.
Alloy eye hooks 1 ton through 22 ton—average straightening load (ultimate load) is 5 times Working Load Limit. Alloy eye hooks 30 tons
through 60 tons—average straightening load (ultimate load) is 4.5 times Working Load Limit. All Alloy shank hooks- average straightening load
(ultimate load) is 4.5 times the Working Load Limit. All Bronze hooks—average straightening load (ultimate load) is 4 times Working Load Limit.
416

Design-A-Crane Hook WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Custom Crane Hook
Hoists
A = ___________________________________________
B = ___________________________________________
C = ___________________________________________
D = ___________________________________________
Services
E = ___________________________________________
F = ___________________________________________
G = ___________________________________________
Engineered
Products
H = ___________________________________________
J = ___________________________________________
K = ___________________________________________
L = ___________________________________________
Slings
M = ___________________________________________
N = ___________________________________________
O = ___________________________________________
Hardware
P = ___________________________________________
Products
Standard Heavy Mill Duty Crane Hooks
Lifting
L
Sizes A B C D E F G H J K M N O P
(min)
5 Ton 1-5/8 1-15/16 2-3/32 1-15/32 3-3/8 3-3/4 3-9/32 13 5-1/4 5 5-1/2 4-13/16 1-7/8 1-5/16 3
10 Ton 2-1/4 2-5/8 2-7/8 2-1/32 4-5/8 4-11/16 4-5/32 17 6-31/32 6-3/4 7 6-7/16 2-17/32 1-25/32 4-1/16
Rope
Wire
15 Ton 2-3/4 3-1/4 3-15/32 2-7/16 5-9/16 5-3/8 4-45/64 19 8-1/4 7-7/8 8-3/8 7-9/16 3-1/32 2-1/8 4-7/8
20 Ton 3-1/4 3-3/4 4 2-25/32 6-3/8 6 5-1/4 20 9-3/8 8-3/4 9-3/8 8-5/8 3-15/32 2-7/16 5-9/16
25 Ton 3-1/2 4-1/16 4-7/16 3-1/8 7-1/8 6-1/2 5-11/16 22 10-3/8 9-1/2 10-1/8 9-1/2 3-29/32 2-3/4 6-1/4
30 Ton 3-3/4 4-5/16 4-27/32 3-3/8 7-3/4 7 6-1/8 24 11-1/4 10-1/2 10-7/8 109/32 4-1/4 2-21/32 6-25/32
Cordage
35 Ton 4-1/4 4-7/8 5-3/16 3-5/8 8-5/16 7-7/16 6-1/2 26 12-1/32 10-7/8 11-7/8 11 4-17/32 3-3/8 7-9/32
40 Ton 4-1/2 5-3/16 5-9/16 3-7/8 8-7/8 7-13/16 6-21/32 27 12-25/32 11-3/8 12-5/8 11-11/16 4-7/8 3-13/32 7-25/32
50 Ton 5 5-3/4 6-3/16 4-5/16 9-7/8 8-9/16 7-1/2 30 14-5/32 12-1/2 14 12-15/16 5-13/32 3-25/32 8-5/8
Securement
60 Ton 5-1/2 6-5/16 6-3/4 4-3/4 10-13/16 9-1/4 8-3/32 32 15-7/16 13-1/2 15-3/8 14-1/8 5-15/16 4-5/32 9-1/2
Load
75 Ton 6 6-7/8 7-1/2 5-1/4 12 10-1/8 8-55/64 34 17-1/16 14-3/8 16-5/8 15-9/16 6-9/16 4-19/32 10-1/2
100 Ton 6-3/4 7-3/4 8-5/8 6-1/32 13-13/16 11-1/2 10-1/16 40 19-9/16 16-25/32 18-7/8 17-27/32 7-9/16 5-19/64 12-3/32
Contact your local Lifting Specialist with your custom dimensions

Contractors
using the drawing from above.

Supply
Protection
Fall

417

Standard Alloy J-Hooks WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
■ Alloy components are 8620 or 4130 alloy steel.
Style A Style B Style C
Material Inside Inside Eye Bowl Tip

Trade Approx. Working
Diameter Reach Diameter Opening Length
Style Size Weight Load Limit
A B C D E
(in.) (lbs.) (lbs.)
(in.) (in.) (in.) (in.) (in.)
A 5/16 .31 5 .75 1.25 .25 .4 250
A 3/8 .38 6 .75 1.5 .38 .42 350
A 1/2 .50 8 .75 2 .5 1.17 650
A 5/8 .63 9 1 2.5 .63 1.5 850
A 3/4 .75 10 1 3 .75 4 1,200
A 7/8 .88 12 1 3.5 .88 5 1,500
A 1 1 14 1.25 4 1 6.5 2,000
A 1-1/8 1.13 15 1.25 4.5 1.12 7.90 2,250
A 1-1/4 1.25 16 1.5 5 1.25 11.50 2,750
A 1-3/8 1.38 17 1.5 5.5 1.38 14.20 3,000
A 1-1/2 1.5 18 2 6 1.5 17.50 3,500
B 5/16 .31 5 .75 1.25 .25 .4 250
B 3/8 .38 6 .75 1.5 .38 .42 350
B 1/2 .50 8 .75 2 .5 1.17 650
B 5/8 .63 9 1 2.5 .63 1.5 850
B 3/4 .75 10 1 3 .75 4 1,200
B 7/8 .88 12 1 3.5 .88 5 1,500
B 1 1 14 1.25 4 1 6.5 2,000
B 1-1/8 1.13 15 1.25 4.5 1.12 7.90 2,250
B 1-1/4 1.25 16 1.5 5 1.25 11.50 2,750
B 1-3/8 1.38 17 1.5 5.5 1.38 14.20 3,000
B 1-1/2 1.5 18 2 6 1.5 17.50 3,500
C 5/16 .31 5 .75 1.25 .25 .4 250
C 3/8 .38 6 .75 1.5 .38 .42 350
C 1/2 .50 8 .75 2 .5 1.17 650
C 5/8 .63 9 1 2.5 .63 1.5 850
C 3/4 .75 10 1 3 .75 4 1,200
C 7/8 .88 12 1 3.5 .88 5 1,500
C 1 1 14 1.25 4 1 6.5 2,000
C 1-1/4 1.25 16 1.5 5 1.25 11.50 2,750
C 1-3/8 1.38 17 1.5 5.5 1.38 14.20 3,000
C 1-1/2 1.5 18 2 6 1.5 17.50 3,500
Larger sizes available upon request.
418

Design-A-J-Hook WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
(MCJH)
Style A Style B Style C
Capacity = ____________________________
Hoists
Quantity = ____________________________ C
Customer = ____________________________
SO # = ____________________________ ØA
DWG # = ____________________________
Services
B
Diameter A = ____________________________
Length B = ____________________________
D
Engineered
Products
Length C = ____________________________ E
Diameter D = ____________________________
Length E = ____________________________
Taper Tip = ______ Yes ______ No
Slings
Special Notes (Sketch taper tip):
Hardware
______________________________________________
______________________________________________
______________________________________________
Products
Lifting
______________________________________________
______________________________________________
Rope
Wire
Cordage
Securement
Load
Contractors
Supply
Protection
Fall

419

S-4320 Latch Kit WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
S-4320 Replacement Latch Kit for

319N, 320N, 322N, 339N and NEW 1327
and 1339 Hooks.
■ Heavy duty stamped latch interlocks with
the hook tip.
■ High cycle, long life spring.
■ Can be made into a “Positive Locking” Hook
when proper cotter pin is utilized.
■ Latch kits shipped unassembled and individually
packaged with instructions.
IMPORTANT: The new S-4320 Latch Kit will not fit

the old style 319, 320 and 322 hooks.
Example of Hook ID
placement location
Hook Size (t) Stock No. Weight Dimensions (in.)

Hook ID
Each
Code
Carbon Alloy Bronze S-4320 SS-4321 * (lbs.) B D E
3/4 1 .5 D 1096325 1097100 .03 .50 .15 1.44
1 1-1/2 .6 F 1096374 1097109 .04 .54 .17 1.56
1-1/2 2 1 G 1096421 1097118 .04 .63 .17 1.66
2 3 1.4 H 1096468 1097127 .06 .66 .17 1.91
3 5 2 I 1096515 1097136 .10 .83 .20 2.31
5 7 3.5 J 1096562 1097145 .15 1.04 .20 2.88
7-1/2 11 5 K 1096609 1097154 .28 1.25 .27 3.56
10 15 6.5 L 1096657 1097163 .33 1.35 .27 3.81
15 22 10 M 1096704 1097172 .84 1.66 .39 5.16
* SS-4320 is Stainless Steel construction with cad plated steel nuts.
420

PL Latch Kits WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Latch Ordering Instructions:
1. Specify PL, PL-N or PL-O latch kit stock number

from charts below.
Hoists
2. Specify capacity of hook to which latch will be
assembled.
3. Specify hook material (carbon or alloy).
■ Hot dip galvanized.
Services
■ Heavy-duty latch with easy operating features.
■ Flapper lever indicates locked or unlocked position.
■ Assembly instructions included with each latch.
■ Meets the intent of OSHA Rule 1926.1431(g) and
Engineered
1926.1501(g) (when secured with the bolt, nut
Products
and pin) for lifting personnel.
IMPORTANT: The PL latch will not work on

319N, 320N or 322N hooks. The PL-N/O Latches,
in the sizes available, will work on both the old
Slings
and new style hooks.
Hardware
Products
Lifting
Hook Size PL Weight Dimensions
(t) Hook ID (in.)
Latch Kit Each
Code
Carbon Alloy Stock No. (lbs.) A B C D E F
3 4-1/2 †I 1093711 0.54 2.57 2.34 1.94 0.56 1.13 2
Rope
Wire
5 7 †J 1093712 0.66 3 2.34 2 0.63 1.38 2.22
7-1/2 11 †K 1093713 1 3.63 2.77 2.38 0.63 1.63 2.38
10 15 †L 1093714 1.25 4 3.22 2.69 0.63 1.88 3.38
15 22 †N 1093715 2.96 5.31 4 2.91 0.84 2.38 3.44
20 30 O 1093716 4.05 6 4.44 3.19 1.06 2.88 4.25
Cordage
25 37 P 1093717 8.63 7 6.63 4.06 2.24 4.5 6.12
30 45 S 1093718 10 6.75 7 4.03 2.24 4.75 6.38
40 60 T 1093719 14.3 8 7.66 4.38 3.46 5.5 7.25
50 75 U 1093720 27 9.88 8.19 5.13 3.38 6.5 8.88
Securement
– 100-150 W-X 1093721 33.25 10.88 11.06 6.38 3.38 7.5 10

Load
– 200 Y 1093723 45 11.88 11.19 6.38 3.38 8.75 11.25

– 300 Z 1093724 55 12.5 12.19 8 3.38 9.75 13
† New 319N style hook.

Contractors
Supply
Protection
Fall

421

PL-N/O Latch Kits WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
1. Specify PL, PL-N or PL-O latch kit stock number

from chart below.
2. Specify capacity of hook to which latch will be
assembled.
■ Heavy-duty latch with easy operating features.

■ PL-N designed for Crosby 319N & 320N style hooks,
PL-O designed for Crosby 319 & 320 old style hooks.
■ Flapper lever indicates locked or unlocked position.
■ Assembly instructions included with each latch.
■ Meets the intent of OSHA Rule 1926.1431(g) and
1926.1501(g) (when secured with the supplied
toggle pin) for lifting personnel.
IMPORTANT: The PL latch will not work on

319N, 320N or 322N hooks. The PL-N/O Latches,
in the sizes available, will work on both the old
and new style hooks.
Hook Size Hook PL-N PL-O Weight Dimensions

(t) ID Latch Kit Latch Kit Each (in.)
Carbon Alloy Code Stock No. Stock No. (lbs.) A B C D E F
3 4.5 / 5 * I 1092000 1091900 0.8 2.40 2.01 0.83 2.13 2.71 3.44
5 7 J 1092001 1091901 1.3 2.94 2.50 1.00 2.52 3.19 3.83
7-1/2 11 K 1092002 1091902 2.0 3.63 3.02 1.19 2.75 3.44 4.38
10 15 L 1092003 1091903 2.8 4.00 3.39 1.34 3.19 4.00 4.50
15 22 N 1092004 1091904 4.9 5.19 4.32 1.61 3.86 4.81 5.13
* “N” style hooks are rated at 5 tons.
422

S-4055 WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Latch Kits
1. Specify latch kit stock number.
Hoists
2. Specify capacity of hook to which latch will
be assembled.
Services
■ Stainless steel construction with cadmium plated
steel nuts.
■ Shipped packaged and unassembled.
■ Instructions included for easy field assembly.
Engineered
Products
Hook Size Hook Weight Dimensions
Stock No.
(t) ID Each (in.)
Carbon Alloy Bronze Code S-4055 (lbs.) A B C D
3/4 1 0.5 D 1090027 0.02 0.38 0.16 1.44 0.59
1 1-1/2 0.6 F 1090045 0.02 0.38 0.16 1.60 0.59
1-1/2 - 2 2-3 1.0 - 1.4 G/H 1090063 0.03 0.47 0.19 1.84 0.82
Slings
3 4-1/2 2.0 I 1090081 0.06 0.56 0.17 2.41 1.00
5 7 3.5 J 1090107 0.11 0.58 0.20 2.97 1.21
7-1/2 - 10 11 - 15 5.0 - 6.5 K/L 1090125 0.17 0.59 0.27 3.66 1.50
15 22 10.0 N 1090143 0.39 0.83 0.39 4.94 1.90
Hardware
20 30 – O 1090161 0.63 0.94 0.52 5.88 2.56
25 - 30 37 - 45 – P/S 1090189 1.12 2.19 0.39 6.50 3.84
40 60 – T 1090205 1.77 3.31 0.52 7.88 4.12
S-4088 Alloy
Products
Lifting
Hook Latch Kits
1. Specify latch kit stock number.
Rope
Wire
2. Specify capacity of hook to which latch will
be assembled.
Cordage
■ To be used on A-327 and A-339 Grade 8 Sling Hooks.
■ Latch Kits shipped unassembled and individually
packaged with instructions. Securement
Hook Size Weight Dimensions

Stock No.
(in) Each (in.)
Load
Carbon S-4088 (lbs.) A B C D

9/32 (1/4) 1090250 .06 .78 .16 2.03 .94
3/8 1090251 .14 1.03 .19 2.69 1.25
Contractors
1/2 1090252 .15 1.03 .19 3.00 1.25

Supply
5/8 1090253 .15 1.03 .19 3.25 1.25

3/4 1090254 .15 1.53 .26 4.13 1.88
7/8 1090255 .15 1.53 .26 4.66 2.00
Protection
Fall

423

Universal WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Latch Kits
Neck Throat Opening

Size of Diameter of Hook
Latch N T
(in.) (in.)
A 9/16" to 5/8" 1-1/16" to 1-1/8"
B 3/4" to 1-3/16" 1-1/4"
C 7/8" to 1" 1-3/8" to 1-1/2"
D 1-1/8" to 1-1/4" 1-3/4" to 1-7/8"
E 1-3/8" to 1-1/2" 2-1/16"
F 1-5/8" to 1-11/16" 2-1/4"
G 1-3/4" to 1-13/16" 2-1/2"
H 1-7/8" to 2" 3"
J 2-1/16" to 2-1/8" 3-3/8"
K 2-3/16" to 2-1/4" 3-1/2"
L 2-5/16" to 2-3/8" 3-3/4"
M 2-7/16" to 2-3/4" 4"
O 3" to 3-1/4" 4-1/2"
424

HG-223 Hook & Hook
Cranes / Jibs
Overhead
Turnbuckles
Meets the performance requirements of Federal
Specifications FF-T-791b, Type 1 Form 1 — CLASS 5,
and ASTM F-1145, except for those provisions
Hoists
■ End fittings are Quenched and Tempered or

Normalized, bodies heat treated by normalizing.
Services
■ Hooks are forged with a greater cross sectional
area that results in a stronger hook with better
fatigue properties.
Engineered
Products
these turnbuckles meet other critical performance
Slings
ASME B30.26.
■ TURNBUCKLES RECOMMENDED FOR STRAIGHT
OR IN-LINE PULL ONLY.
■ Modified UNJ thread on end fittings for improved
fatigue properties.
Hardware
■ Body has UNC threads.
■ Lock Nuts available for all sizes.
■ Fatigue Rated.
Thread Working
Products
Lifting
Dia. & Load
No. Each (in.)
Take Up Limit
E J K M N
in. HG-223 lbs. * lbs. A D F BB
Closed Open Closed Open Closed
† 1/4 x 4 1030011 400 .33 .25 .44 1.67 1.27 9.79 7.38 12.20 8.20 4.07
Rope
Wire
† 5/16 x 4-1/2 1030039 700 .52 .31 .50 2.00 1.50 11.58 8.58 14.08 9.58 4.58
† 3/8 x 6 1030057 1,000 .83 .38 .56 2.28 1.77 15.23 10.62 17.84 11.84 6.10
1/2 x 6 1030075 1,500 1.88 .50 .65 3.53 2.28 17.98 13.20 20.76 14.76 6.03
1/2 x 12 1030119 1,500 2.77 .50 .65 3.51 2.28 30.27 19.49 33.05 21.05 12.36
5/8 x 6 1030137 2,250 3.21 .63 .90 4.24 2.81 19.50 14.50 22.50 16.50 6.03
Cordage
5/8 x 12 1030173 2,250 4.58 .63 .90 4.23 2.81 31.84 20.84 34.84 22.84 12.39
3/4 x 6 1030191 3,000 4.20 .75 .98 5.07 3.33 21.19 15.98 24.40 18.40 6.13
3/4 x 12 1030235 3,000 6.92 .75 .98 5.04 3.33 33.59 22.38 36.80 24.80 12.59
3/4 x 18 1030253 3,000 8.65 .75 .98 5.07 3.33 45.59 28.38 48.80 30.80 18.53
Securement
7/8 x 12 1030271 4,000 9.85 .88 1.13 5.82 3.78 34.89 23.52 38.26 26.26 12.16
Load
1 x 12 1030333 5,000 14.8 1.00 1.25 6.56 4.25 36.59 25.06 40.12 28.12 12.18
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
† Mechanical Galvanized
Contractors
Supply
Protection
Fall

425

HG-225 Hook & Eye
Turnbuckles
Specifications FF-T-791b, Type 1, Form 1 — CLASS 6,
and ASTM F-1145, except for those provisions required
of the contractor.
■ End fittings are Quenched and Tempered or Normalized,

bodies heat treated by normalizing.
■ Turnbuckle eyes are forged elongated, by design, to
maximize easy attachment in system and minimize
stress in the eye. For turnbuckles sizes 1/4" through
1", a shackle one size smaller can be reeved
through eye.
■ Turnbuckle hooks are forged with a greater cross
sectional area that results in a stronger hook with better
fatigue properties.
including identification, ductility, design factor, proof
load and temperature requirements. Importantly, these
turnbuckles meet other critical performance
ASME B30.26.
■ TURNBUCKLES RECOMMENDED FOR STRAIGHT ■ Body has UNC threads.
OR IN-LINE PULL ONLY. ■ Lock Nuts available for all sizes.
■ Modified UNJ thread on end fittings for improved ■ Fatigue Rated.
fatigue properties.
Thread Working
Dia. & Load
No. Each (in.)
Take Up Limit
E J K M N X
in. HG-225 lbs. * lbs. A D F R S BB
Closed Open Closed Open Closed Closed
† 1/4 x 4 1030636 400 .31 .25 .44 1.67 1.27 11.66 7.66 12.29 8.29 .81 .34 1.76 4.07
† 5/16 x 4-1/2 1030654 700 .50 .31 .50 2.00 1.50 13.50 9.00 14.28 9.78 .95 .44 2.20 4.58
† 3/8 x 6 1030672 1,000 .79 .38 .56 2.28 1.76 17.09 11.09 18.04 12.04 1.13 .53 2.48 6.10
1/2 x 6 1030690 1,500 1.80 .50 .65 3.53 2.28 19.57 13.57 20.79 14.79 1.41 .71 3.56 6.03
1/2 x 12 1030734 1,500 2.70 .50 .65 3.51 2.28 31.86 19.86 33.08 21.08 1.41 .71 3.54 12.36
5/8 x 6 1030752 2,250 2.98 .63 .90 4.24 2.81 21.11 15.11 22.61 16.61 1.80 .88 4.35 6.03
5/8 x 12 1030798 2,250 4.35 .63 .90 4.23 2.81 33.45 21.45 34.95 22.95 1.80 .88 4.34 12.39
3/4 x 6 1030814 3,000 4.21 .75 .98 5.07 3.33 22.61 16.61 24.45 18.45 2.09 1.00 5.12 6.13
3/4 x 12 1030850 3,000 6.52 .75 .98 5.04 3.33 35.01 23.01 36.85 24.85 2.09 1.00 5.09 12.59
3/4 x 18 1030878 3,000 8.24 .75 .98 5.07 3.33 47.01 29.01 48.85 30.85 2.09 1.00 5.12 18.53
7/8 x 12 1030896 4,000 9.34 .88 1.13 5.82 3.78 36.11 24.11 38.23 26.23 2.38 1.25 5.79 12.16
1 x 12 1030958 5,000 13.9 1.00 1.25 6.56 4.25 37.65 25.65 40.06 28.06 3.00 1.43 6.50 12.18
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
† Mechanical Galvanized
426

HG-226 Eye & Eye
Cranes / Jibs
Overhead
Turnbuckles
Specifications FF-T-791b, Type 1, Form 1 — CLASS 4,
and ASTM F-1145, except for those provisions
Hoists

Services
■ Turnbuckle eyes are forged elongated, by design,
to maximize easy attachment in system and minimize
stress in the eye. For turnbuckle sizes 1/4" through
2-1/2", a shackle one size smaller can be reeved
Engineered
through eye.
Products
■ Modified UNJ thread on end fittings for improved fatigue
properties. Body has UNC threads.
including identification, ductility, design factor, proof load
and temperature requirements. Importantly, these
Slings
turnbuckles meet other critical performance ■ TURNBUCKLES RECOMMENDED FOR STRAIGHT
requirements, including fatigue life, impact properties OR IN-LINE PULL ONLY.
and material traceability, not addressed by ■ Lock Nuts available for all sizes.
ASME B30.26. ■ Fatigue Rated.
Hardware
Thread Working
Dia. & Load
No. Each (in.)
Take Up Limit
J K M N X
in. HG-226 lbs. * lbs. A R S BB
Open Closed Open Closed Closed
Products
Lifting
† 1/4 x 4 1031252 500 .29 .25 11.94 7.94 12.38 8.38 .81 .34 1.76 4.07
† 5/16 x 4-1/2 1031270 800 .48 .31 13.92 9.42 14.48 9.98 .95 .44 2.20 4.58
† 3/8 x 6 1031298 1,200 .75 .38 17.56 11.56 18.24 12.24 1.13 .53 2.48 6.10
1/2 x 6 1031314 2,200 1.72 .50 19.94 13.94 20.82 14.82 1.41 .71 3.56 6.03
1/2 x 12 1031350 2,200 2.63 .50 32.23 20.23 33.11 21.11 1.41 .71 3.54 12.36
5/8 x 6 1031378 3,500 2.75 .63 21.72 15.72 22.72 16.72 1.80 .88 4.35 6.03
Rope
Wire
5/8 x 12 1031412 3,500 4.12 .63 34.06 22.06 35.06 23.06 1.80 .88 4.34 12.39
3/4 x 6 1031430 5,200 4.22 .75 23.24 17.24 24.50 18.50 2.09 1.00 5.12 6.13
3/4 x 12 1031476 5,200 6.12 .75 35.64 23.64 36.90 24.90 2.09 1.00 5.09 12.59
3/4 x 18 1031494 5,200 7.83 .75 47.64 29.64 48.90 30.90 2.09 1.00 5.12 18.53
7/8 x 12 1031519 7,200 8.83 .88 36.70 24.70 38.20 26.20 2.38 1.25 5.79 12.16
7/8 x 18 1031537 7,200 11.5 .88 49.17 31.17 50.67 32.67 2.38 1.25 5.79 18.63
Cordage
1x6 1031555 10,000 9.62 1.00 26.24 20.24 28.00 22.00 3.00 1.43 6.50 6.18
1 x 12 1031573 10,000 13.0 1.00 38.24 26.24 40.00 28.00 3.00 1.43 6.50 12.18
1 x 18 1031591 10,000 16.3 1.00 50.24 32.24 52.00 34.00 3.00 1.43 6.50 18.18
1 x 24 1031617 10,000 20.2 1.00 62.84 38.84 64.60 40.60 3.00 1.43 6.47 24.84
1-1/4 x 12 1031635 15,200 19.9 1.25 42.14 30.14 44.38 32.38 3.59 1.82 8.49 12.06
1-1/4 x 18 1031653 15,200 23.8 1.25 54.14 36.14 56.38 38.38 3.59 1.82 8.49 18.06
Securement
1-1/4 x 24 1031671 15,200 27.8 1.25 66.70 42.70 68.94 44.94 3.59 1.82 8.49 24.62
Load
1-1/2 x 12 1031699 21,400 28.7 1.50 44.24 32.24 46.74 34.74 4.09 2.12 9.46 12.32
1-1/2 x 18 1031715 21,400 34.1 1.50 56.24 38.24 58.74 40.74 4.09 2.12 9.46 18.32
1-1/2 x 24 1031733 21,400 39.6 1.50 68.86 44.86 71.36 47.36 4.09 2.12 9.46 24.94
1-3/4 x 18 1031779 28,000 50.7 1.75 57.38 39.38 60.38 42.38 4.65 2.38 9.97 18.37
1-3/4 x 24 1031797 28,000 58.2 1.75 69.38 45.38 72.38 48.38 4.65 2.38 9.97 24.37
Contractors
2 x 24 1031813 37,000 83.5 2.00 75.68 51.68 79.18 55.18 5.81 2.69 13.03 24.48
Supply
2-1/2 x 24 1031831 60,000 149 2.50 79.18 55.18 83.18 59.18 6.49 3.12 13.76 24.60
2-3/4 x 24 1031859 75,000 174 2.75 81.34 57.34 85.84 61.84 7.00 3.25 15.09 24.65
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit. † Mechanical Galvanized
Protection
Fall

427

HG-227 Jaw & Eye
Turnbuckles
Meets the performance requirements of Federal Specifications
FF-T-791b, Type 1, Form 1 — CLASS 8, and ASTM F-1145, except
for those provisions required of the contractor.

■ Turnbuckles eyes are forged and elongated, by design, to maximize
easy attachment in system and minimize stress in the eye.
For turnbuckles size 1/4" through 2-1/2", a shackle one size smaller
can be reeved through eye.
■ Forged jaw ends are fitted with bolts and nuts for 1/4" through 5/8",
and pins and cotters on 3/4" through 2-3/4" sizes.
■ Modified UNJ thread on end fittings for improved fatigue properties.
identification, ductility, design factor, proof load and temperature
requirements. Importantly, these turnbuckles meet other critical
performance requirements, including fatigue life, impact properties
and material traceability, not addressed by ASME B30.26.
■ TURNBUCKLES RECOMMENDED FOR STRAIGHT OR ■ Lock Nuts available for all sizes.
IN-LINE PULL ONLY. ■ Fatigue Rated.
Thread Working
Dia. & Load
No. Each (in.)
Take Up Limit
E J K M N X
in. HG-227 lbs. * lbs. A B G R S BB
Closed Open Closed Open Closed Closed
† 1/4 x 4 1031877 500 .33 .25 .45 1.66 .64 11.57 7.57 12.28 8.28 .81 .34 1.76 4.07
† 5/16 x 4-1/2 1031895 800 .52 .31 .50 2.02 .87 13.50 9.00 14.30 9.80 .95 .44 2.20 4.58
† 3/8 x 6 1031911 1,200 .80 .38 .53 2.11 .85 16.91 10.91 17.87 11.87 1.13 .53 2.48 6.10
1/2 x 6 1031939 2,200 1.77 .50 .64 3.22 1.07 19.30 13.30 20.48 14.48 1.41 .71 3.56 6.03
1/2 x 9 1031957 2,200 2.25 .50 .64 3.20 1.07 25.59 16.59 26.77 17.77 1.41 .71 3.54 9.36
1/2 x 12 1031975 2,200 2.67 .50 .64 3.20 1.07 31.59 19.59 32.77 20.77 1.41 .71 3.54 12.36
5/8 x 6 1031993 3,500 2.98 .63 .79 3.90 1.32 20.73 14.73 22.27 16.27 1.80 .88 4.35 6.03
5/8 x 9 1032019 3,500 3.72 .63 .79 3.89 1.32 27.07 18.07 28.61 19.61 1.80 .88 4.34 9.39
5/8 x 12 1032037 3,500 4.35 .63 .79 3.89 1.32 33.07 21.07 34.61 22.61 1.80 .88 4.34 12.39
3/4 x 6 1032055 5,200 4.51 .75 .97 4.71 1.52 22.17 16.17 24.09 18.09 2.09 1.00 5.12 6.13
3/4 x 9 1032073 5,200 5.56 .75 .97 4.68 1.52 28.57 19.57 30.49 21.49 2.09 1.00 5.09 9.59
3/4 x 12 1032091 5,200 6.42 .75 .97 4.68 1.52 34.57 22.57 36.49 24.49 2.09 1.00 5.09 12.59
3/4 x 18 1032117 5,200 8.14 .75 .97 4.71 1.52 46.57 28.57 48.49 30.49 2.09 1.00 5.12 18.53
7/8 x 12 1032135 7,200 9.10 .88 1.16 5.50 1.77 35.68 23.68 37.91 25.91 2.38 1.25 5.79 12.16
7/8 x 18 1032153 7,200 11.6 .88 1.16 5.50 1.77 48.15 30.15 50.38 32.38 2.38 1.25 5.79 18.63
1x6 1032171 10,000 10.0 1.00 1.34 6.09 2.05 25.03 19.03 27.59 21.59 3.00 1.43 6.50 6.18
1 x 12 1032199 10,000 13.4 1.00 1.34 6.09 2.05 37.03 25.03 39.59 27.59 3.00 1.43 6.50 12.18
1 x 18 1032215 10,000 16.7 1.00 1.34 6.09 2.05 49.03 31.03 51.59 33.59 3.00 1.43 6.50 18.18
1 x 24 1032233 10,000 20.6 1.00 1.34 6.06 2.05 61.63 37.63 64.19 40.19 3.00 1.43 6.47 24.84
1-1/4 x 12 1032251 15,200 20.9 1.25 1.84 8.09 2.82 40.76 28.76 43.98 31.98 3.59 1.82 8.49 12.06
1-1/4 x 18 1032279 15,200 24.8 1.25 1.84 8.09 2.82 52.76 34.76 55.98 37.98 3.59 1.82 8.49 18.06
1-1/4 x 24 1032297 15,200 28.8 1.25 1.84 8.09 2.82 65.32 41.32 68.54 44.54 3.59 1.82 8.49 24.62
1-1/2 x 12 1032313 21,400 30.6 1.50 2.06 8.93 2.81 42.50 30.50 46.21 34.21 4.09 2.12 9.46 12.32
1-1/2 x 18 1032331 21,400 36.0 1.50 2.06 8.93 2.81 54.50 36.50 58.21 40.21 4.09 2.12 9.46 18.32
1-1/2 x 24 1032359 21,400 41.5 1.50 2.06 8.93 2.81 67.12 43.12 70.83 46.83 4.09 2.12 9.46 24.94
1-3/4 x 18 1032395 28,000 52.1 1.75 2.60 9.36 3.35 55.37 37.37 59.77 41.77 4.65 2.38 9.97 18.37
1-3/4 x 24 1032411 28,000 59.7 1.75 2.60 9.36 3.35 67.37 43.37 71.77 47.77 4.65 2.38 9.97 24.37
2 x 24 1032439 37,000 89.9 2.00 2.62 11.80 3.74 72.66 48.66 77.95 53.95 5.81 2.69 13.03 24.48
2-1/2 x 24 1032457 60,000 158 2.50 3.06 13.26 4.44 76.08 52.08 82.68 58.68 6.49 3.12 13.76 24.60
2-3/4 x 24 1032475 75,000 187 2.75 3.69 14.92 4.19 78.05 54.05 85.67 61.67 7.00 3.25 15.09 24.65
428

HG-228 Jaw & Jaw
Cranes / Jibs
Overhead
Turnbuckles
Meets the performance requirements of Federal Specifications
FF-T-791b,Type 1, Form 1 — CLASS 7, and ASTM F-1145, except
for those provisions required of the contractor.
Hoists
■ TURNBUCKLES RECOMMENDED FOR STRAIGHT
Services
OR IN-LINE PULL ONLY.
■ Forged jaw ends are fitted with bolts and nuts for 1/4" through 5/8",
and pins and cotters on 3/4" through 2-3/4" sizes.
■ Modified UNJ thread on end fittings for improved fatigue properties.
Engineered
Products
identification, ductility, design factor, proof load and temperature
requirements. Importantly, these turnbuckles meet other critical
performance requirements, including fatigue life, impact properties
and material traceability, not addressed by ASME B30.26.
■ Lock Nuts available for all sizes.
Slings
■ Fatigue Rated.
Thread Working
Dia. & Load
Hardware
No. Each (in.)
Take Up Limit
E J K M N
in. HG-228 lbs. * lbs. A B G BB
Closed Open Closed Open Closed
† 1/4 x 4 1032493 500 .37 .25 .45 1.66 .64 11.19 7.19 12.18 8.18 4.07
† 5/16 x 4-1/2 1032518 800 .56 .31 .50 2.02 .87 13.07 8.57 14.12 9.62 4.58
Products
Lifting
† 3/8 x 6 1032536 1,200 .85 .38 .53 2.11 .85 16.25 10.25 17.50 11.50 6.10
1/2 x 6 1032554 2,200 1.82 .50 .64 3.22 1.07 18.65 12.65 20.14 14.14 6.03
1/2 x 9 1032572 2,200 2.29 .50 .64 3.20 1.07 24.94 15.94 26.43 17.43 9.36
1/2 x 12 1032590 2,200 2.71 .50 .64 3.20 1.07 30.94 18.94 32.43 20.43 12.36
5/8 x 6 1032616 3,500 3.21 .63 .79 3.90 1.32 19.74 13.74 21.82 15.82 6.03
5/8 x 9 1032634 3,500 3.95 .63 .79 3.89 1.32 26.08 17.08 28.16 19.16 9.39
5/8 x 12 1032652 3,500 4.58 .63 .79 3.89 1.32 32.08 20.08 34.16 22.16 12.39
Rope
Wire
3/4 x 6 1032670 5,200 4.80 .75 .97 4.71 1.52 21.09 15.09 23.68 17.68 6.13
3/4 x 9 1032698 5,200 5.85 .75 .97 4.68 1.52 27.49 18.49 30.08 21.08 9.59
3/4 x 12 1032714 5,200 6.72 .75 .97 4.68 1.52 33.49 21.49 36.08 24.08 12.59
3/4 x 18 1032732 5,200 8.45 .75 .97 4.71 1.52 45.49 27.49 48.08 30.08 18.53
7/8 x 12 1032750 7,200 9.37 .88 1.16 5.50 1.77 34.65 22.65 37.62 25.62 12.16
7/8 x 18 1032778 7,200 11.8 .88 1.16 5.50 1.77 47.12 29.12 50.09 32.09 18.63
Cordage
1x6 1032796 10,000 10.4 1.00 1.34 6.09 2.05 23.82 17.82 27.18 21.18 6.18
1 x 12 1032812 10,000 13.8 1.00 1.34 6.09 2.05 35.82 23.82 39.18 27.18 12.18
1 x 18 1032830 10,000 17.1 1.00 1.34 6.09 2.05 47.82 29.82 51.18 33.18 18.18
1 x 24 1032858 10,000 21.0 1.00 1.34 6.06 2.05 60.42 36.42 63.78 39.78 24.84
1-1/4 x 12 1032876 15,200 21.9 1.25 1.84 8.09 2.82 39.37 27.37 43.58 31.58 12.06
1-1/4 x 18 1032894 15,200 25.9 1.25 1.84 8.09 2.82 51.37 33.37 55.58 37.58 18.06
Securement
1-1/4 x 24 1032910 15,200 29.8 1.25 1.84 8.09 2.82 63.93 39.93 68.14 44.14 24.62
Load
1-1/2 x 12 1032938 21,400 32.6 1.50 2.06 8.93 2.81 40.76 28.76 45.68 33.68 12.32
1-1/2 x 18 1032956 21,400 38.0 1.50 2.06 8.93 2.81 52.76 34.76 57.68 39.68 18.32
1-1/2 x 24 1032974 21,400 43.5 1.50 2.06 8.93 2.81 65.38 41.38 70.30 46.30 24.94
1-3/4 x 18 1033018 28,000 53.5 1.75 2.60 9.36 3.35 53.35 35.35 59.16 41.16 18.37
1-3/4 x 24 1033036 28,000 61.1 1.75 2.60 9.36 3.35 65.35 41.35 71.16 47.16 24.37
Contractors
2 x 24 1033054 37,000 96.3 2.00 2.62 11.80 3.74 69.64 45.64 76.72 52.72 24.48
Supply
2-1/2 x 24 1033072 60,000 167 2.50 3.06 13.26 4.44 72.97 48.97 82.18 58.18 24.60
2-3/4 x 24 1033090 75,000 199 2.75 3.69 14.92 4.19 74.75 50.75 85.50 61.50 24.65
Protection
Fall

429

Turnbuckle Data
Hook—
Dimensions &
Strength
Hook—Dimensions (in.) Working Load

A B C D E Limit (lbs.)
1/4 1/4 13/32 29/64 1-21/32 400
5/16 5/16 1/2 1/2 1-31/32 700
3/8 3/8 39/64 9/16 2-23/64 1,000
1/2 1/2 25/32 21/32 2-15/16 1,500
5/8 5/8 1 27/32 3-11/16 2,250
3/4 3/4 1-13/64 63/64 4-33/64 3,000
7/8 7/8 1-3/8 1-1/8 5-3/16 4,000
1 1 1-17/32 1-1/4 5-27/32 5,000
1-1/4 1-1/4 1-13/16 1-1/2 7-7/32 5,000
1-1/2 1-5/16 1-3/4 1-7/8 8-11/32 7,500
Eye—
Dimensions &
Strength
Eye—Dimensions (in.) Working Load

A B C D E Limit (lbs.)
1/4 11/32 7/32 25/32 1-25/32 500
5/16 7/16 9/32 15/16 2-3/16 800
3/8 17/32 11/32 1-1/8 2-9/16 1,200
1/2 23/32 7/16 1-7/16 3-7/32 2,200
5/8 7/8 1/2 1-3/4 3-7/8 3,500
3/4 1 5/8 2-1/8 4-11/16 5,200
7/8 1-1/4 3/4 2-3/8 5-1/4 7,200
1 1-7/16 7/8 3 6-3/8 10,000
1-1/4 1-13/16 1-1/8 3-9/16 7-3/4 15,200
1-1/2 2-1/8 1-1/4 4-1/8 8-5/8 21,400
1-3/4 2-3/8 1-1/2 4-11/16 10 28,000
2 2-11/16 1-3/4 5-3/4 12-1/8 37,000
2-1/2 3-1/8 2 6-1/2 13-9/16 60,000
2-3/4 3-1/4 2-1/4 7 15 75,000
430

Turnbuckle Data
Cranes / Jibs
Overhead
(Continued)
Jaw—
Dimensions &
Hoists
Strength
Services
Jaw—Dimensions (in.) Working Load
Engineered
Products
A B C D E F G Limit (lbs.)
1/4 5/8 1/4 13/32 9/32 1/2 1-5/8 500
5/16 7/8 1/4 15/32 9/32 1/2 2 800
3/8 7/8 5/16 1/2 5/16 19/32 2-3/16 1,200
1/2 1-1/16 3/8 5/8 13/32 3/4 2-3/4 2,200
5/8 1-5/16 1/2 3/4 1/2 1-1/32 3-1/2 3,500
Slings
3/4 1-1/2 5/8 15/16 9/16 1-9/32 4-1/8 5,200
7/8 1-3/4 3/4 1-1/8 11/16 1-15/32 4-27/32 7,200
1 2-1/16 7/8 1-3/16 25/32 1-21/32 5-17/32 10,000
1-1/4 2-13/16 1-1/8 1-3/4 1 2-3/32 7-3/16 15,200
1-1/2 2-13/16 1-3/8 2-1/16 1-1/16 2-15/32 7-7/8 21,400
1-3/4 3-3/8 1-5/8 2-3/8 1-1/4 2-29/32 9-3/8 28,000
Hardware
2 3-11/16 2 2-1/2 1-9/16 3-17/32 10-7/8 37,000
2-1/2 4-7/16 2-1/4 2-7/8 1-9/16 4-5/8 13-11/32 60,000
2-3/4 4-3/16 2-3/4 3-1/2 1-5/8 5-3/8 15 75,000
Body—
Products
Lifting
Dimensions &
Strength
Rope
Wire
Body—Dimensions (in.) Working Load
A B S T Limit (lbs.)
1/4 4 4-3/4 3/8 500
Cordage
5/16 4-1/2 5-7/16 15/32 800
3/8 6 7-1/8 9/16 1,200
1/2 6 7-1/2 3/4 2,200
5/8 6 7-7/8 15/16 3,500
3/4 6 8-1/4 1-1/8 5,200
7/8 6 8-5/8 1-5/16 7,200
Securement
1 6 9 1-1/2 10,000
1 12 15 1-1/2 10,000
Load
1 18 21 1-1/2 10,000
1 24 27 1-1/2 10,000
1-1/4 12 15-1/8 1-9/16 15,200
1-1/4 18 21-1/8 1-9/16 15,200
1-1/2 12 15-3/4 1-7/8 21,400
Contractors
1-1/2 18 21-3/4 1-7/8 21,400

Supply
1-3/4 18 22-3/8 2-3/16 28,000

2 24 29 2-1/2 37,000
2-3/4 24 31 3-1/2 75,000
Protection
Fall

431

VRS WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
STARPOINT Eye Bolt

The Absolute STAR Among Eye Bolts
hape: Star shaped - clear distinction from standard

S
eye bolt DIN 580.
Color: Striking fluorescent pink powder coating
Marking: Clear indication of WLL (in metric tons and lbs.) for
side load direction F (not allowed with standard eye bolt).
■ Forged material 1.6541, alloy quenched and tempered,
100% electromagnetic crack detected according to EN 1677-4
■ Safety factor 4:1.
■ Workpiece material must conform to minimum steel quality
S235JR (1.0037).
■ Countersink of tapped hole = nominal thread diameter.
■ Provide plane seat of the special hexagon bolt.
■ VRS must be able to rotate by 360° in bolted condition.
■ Adjust to load direction before loading.
■ Component protected by patents:
- Europe patent EP 654 611.
- US patent 5690457.
Specifically engineered Grade 10.9 captive hexagon socket screw.

Simply engage the hexagon socket bolt with the star profile key –
use your fingers to respectively tighten or untighten the arrangement.
Disengage the key before you hook in the lifting mean. Do not use
an elongation piece.
Measurements in Inches
WLL Weight Quantity Ref. No.
Type
(lbs.) (lbs.) Per Box VRS-F
A B C D E G K L M N S
VRS-1/4"-20UNC 220 (1,100) 0.13 1-5/64 23/64 17/64 25/32 29/32 1-7/64 1-29/64 23/64 1/4 7/32 33/64 4 7999105
VRS-5/16"-18UNC 660 (2,090) 0.25 1-11/32 7/16 11/32 1 1 1-19/64 1-13/16 15/32 5/16 1/4 41/64 1 7999106
VRS-3/8"-16UNC 880 (2,200) 0.26 1-11/32 7/16 11/32 1 1 1-19/64 1-13/16 9/16 3/8 1/4 9/16 20 7104480
VRS-7/16"-14UNC 880 (2,200) 0.26 1-11/32 7/16 21/64 11/32 1 1-19/64 1-13/16 19/32 7/16 1/4 41/64 4 7999272
VRS-1/2"-13UNC 1,650 (4,400) 0.45 1-21/32 1/2 11/32 1-3/16 1-3/16 1-11/32 2-3/16 3/4 1/2 5/16 23/64 20 7104481
VRS-5/8"-11UNC 3,300 (8,820) 0.75 1-15/16 19/32 9/16 1-3/8 1-3/8 1-9/16 2-9/16 15/16 5/8 3/8 7/8 10 7104482
VRS-3/4"-10UNC 5,070 (13,250) 1.2 2-1/4 21/32 5/8 1-9/16 1-9/16 2 2-15/16 1-3/16 3/4 1/2 1-3/32 10 7104483
VRS-7/8"-9UNC 5,070 (13,250) 1.3 2-1/4 21/32 5/8 1-9/16 1-9/16 2 2-15/16 1-5/32 7/8 1/2 1-3/32 10 7104484
VRS-1"-8UNC 7,050 (17,630) 2.2 2-23/32 13/16 3/4 1-7/8 1-7/8 2-3/8 3-17/32 1-1/2 1 9/16 1-5/16 10 7104485
VRS-1-1/4"-7UNC 9,920 (26,450) 4.2 3-3/8 1 15/16 2-3/8 2-3/8 2-15/16 4-13/32 1-7/8 1-1/4 5/8 1-21/32 4 7104486
VRS-1-1/2"-6UNC 15,430 (35,270) 7.6 4 1-1/4 1-1/8 2-27/32 2-15/16 3-17/32 5-5/16 2-1/8 1-1/2 7/8 1-31/32 1 7984221
VRS-1-3/4"-5UNC 19,480 (52,910) 11.6 4-3/4 1-1/2 1-11/32 3-7/32 3-11/32 4-1/8 6-1/4 2-1/2 1-3/4 1 2-9/32 2 7104488
VRS-2"-4.5UNC 26,450 (70,540) 17.5 5-3/8 1-11/16 1-1/2 3-11/16 3-15/16 4-3/4 7-1/16 2-13/16 2 1-1/8 2-19/32 1 7984223
Attention: Lateral forces with standard eye bolts according to DIN 580 are forbidden! In case of multiple leg suspensions, 2-leg and 3/4-legs,
the ring-eye plane of the ring bolt must be in the direction of pull. This is not likely to be the case if standard eye bolts are tightened.
432

Forged Eye Bolts WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Drop forged steel. Heat treated after forging.
Self-colored, zinc plated or hot galvanized. Plain or
shoulder type, blank or threaded. Threaded will be
supplied unless otherwise specified.
Hoists
Standard Shank Lengths—
Plain Pattern
Services
Bolt Standard
Plain Weight
Diameter Shank Part
Pattern Per
N.C. Length No.
No. 100
(in.) (in.)
Engineered
1 1/4 1 11005-1 5.5
Products
2 5/16 1-1/8 11025-9 11.5
3 3/8 1-1/4 11045-7 16.5
4 7/16 1-3/8 11065-5 22
5 1/2 1-1/2 11085-3 35
6 9/16 1-5/8 11105-8 45
7 5/8 1-3/4 11125-6 66
Slings
8 3/4 2 11148-5 97
9 7/8 2-1/4 11168-3 142
10 1 2-1/2 11188-1 199
11 1-1/8 2-3/4 11208-6 312
12 1-1/4 3 11231-4 412
14 1-1/2 3-1/2 11251-2 691
Hardware
Standard Shank Lengths—
Shoulder Pattern
Products
Lifting
Bolt Standard
Shoulder Weight
Diameter Shank Part
Pattern Per
N.C. Length No.
No. 100
(in.) (in.)
21 1/4 1 12805-6 6
Rope
Wire
22 5/16 1-1/8 12825-4 10
23 3/8 1-1/4 12845-2 16
24 7/16 1-3/8 12865-0 26.5
25 1/2 1-1/2 12885-8 38
26 9/16 1-5/8 12905-3 49
27 5/8 1-3/4 12925-1 73.5
Cordage
28 3/4 2 12948-0 99.5
29 7/8 2-1/4 12968-8 172.5
30 1 2-1/2 12988-6 235
31 1-1/8 2-3/4 13008-0 342.5
32 1-1/4 3 13031-8 462.5
Securement
34 1-1/2 3-1/2 13051-6 752.5

Load
Contractors
Supply
Protection
Fall

433

Metric Eye Bolts WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Forged, Carbon Steel,

Self-colored, Shoulder Pattern
Approx.
Shank I.D.
Approx. Thread Weight Working Working
Part Metric Length Eye
Equivalent Size Per 100 Load Limit Load Limit
No. Size B C
(in.) A Pcs. (kgs.) (lbs.)
(mm) (mm)
(lbs.)
13805-5 M6 1/4 M6 x 1.0 25.4 19 6 210 462
13825-3 M7 5/16 M7 x 1.0 28.5 22 10 370 814
13845-1 M8 3/8 M8 x 1.25 31.7 25 16 450 992
13865-9 M10 7/16 M10 x 1.5 35 28 21 740 1,628
13885-7 M12 1/2 M12 x 1.75 38 30 38 1,030 2,266
13905-2 M14 9/16 M14 x 2.0 44.5 35 73 1,600 3,520
13925-0 M16 5/8 M16 x 2.0 44.5 35 73 1,600 3,520
13948-9 M18 3/4 M18 x 2.5 51 38 104 2,140 4,708
13968-7 M20 7/8 M20 x 2.5 57 43 161 2,860 6,292
13988-5 M24 1 M24 x 3.0 63.5 46 231 3,850 8,470
14008-9 M27 1-1/8 M27 x 3.0 70 51 335 5,200 11,440
14031-7 M30 1-1/4 M30 x 3.5 76 55 439 6,400 14,080
14051-5 M36 1-1/2 M36 x 4.0 89 63 731 8,970 19,734
Some sizes available in stainless steel.
Stainless Steel Eye Bolts

Machinery Eye Bolts Plain Pattern—Threaded Type 316 Stainless Steel
Bolt Standard Weight

Plain Part
Diameter Shank Per 100
Pattern No. No.
(in.) (in.) (lbs.)
1SS 1/4 1 14205-2 5
2SS 5/16 1-1/8 14210-6 10.5
3SS 3/8 1-1/4 14215-1 15.5
5SS 1/2 1/23/8 14220-5 33
7SS 5/8 1-3/4 14225-0 64
8SS 3/4 2 14230-4 90.5
Machinery Eye Bolts Shoulder Pattern—Threaded Type 316 Stainless Steel
Bolt Standard Weight

Shoulder Part
Diameter Shank Per 100
Pattern No. No.
(in.) (in.) (lbs.)
21SS 1/4 1 13105-6 6
22SS 5/16 1-1/8 13125-4 10
23SS 3/8 1-1/4 13145-2 16
25SS 1/2 1/23/8 13185-8 38
27SS 5/8 1-3/4 13225-1 73.5
28SS 3/4 2 13248-0 99.5
434

G-291 Regular WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Cranes / Jibs
Overhead
Nut Eye Bolts
■ Fatigue rated at 1-1/2 times the Working Load Limit
at 20,000 cycles.
Hoists
■ All Bolts Hot Dip galvanized after threading (UNC).
■ Furnished with standard Hot Dip galvanized hex nuts.
■ Recommended for in-line pull.
Services
and temperature requirements. Importantly, these bolts
meet other critical performance requirements, including
fatigue life, impact properties and material traceability,
not addressed by ASME B30.26.
Engineered
Products
Shank Stock Working Dimensions
Weight
Dia. & No. Load (in.)
Per 100
Length Limit
Slings
(lbs.)
(in.) (lbs.) *
G-291 A B C D E F G H
1/4 x 2 1043230 650 8.20 .25 .50 1.00 .25 1.50 2.00 3.06 .56
1/4 x 4 1043258 650 11.70 .25 .50 1.00 .25 2.50 4.00 5.06 .56
5/16 x 2-1/4 1043276 1,200 13.30 .31 .62 1.25 .31 1.50 2.25 3.56 .69
Hardware
5/16 x 4-1/4 1043294 1,200 25.00 .31 .62 1.25 .31 2.50 4.25 5.56 .69
3/8 x 2-1/2 1043310 1,550 23.30 .38 .75 1.50 .38 1.50 2.50 4.12 .88
3/8 x 4-1/2 1043338 1,550 29.50 .38 .75 1.50 .38 2.50 4.50 6.12 .88
3/8 x 6 1043356 1,550 35.20 .38 .75 1.50 .38 2.50 6.00 7.62 .88
1/2 x 3-1/4 1043374 2,600 50.30 .50 1.00 2.00 .50 1.50 3.25 5.38 1.12
1/2 x 6 1043392 2,600 66.10 .50 1.00 2.00 .50 3.00 6.00 8.12 1.12
Products
Lifting
1/2 x 8 1043418 2,600 82.00 .50 1.00 2.00 .50 3.00 8.00 10.12 1.12
1/2 x 10 1043436 2,600 88.00 .50 1.00 2.00 .50 3.00 10.00 12.12 1.12
1/2 x 12 1043454 2,600 114.20 .50 1.00 2.00 .50 3.00 12.00 14.12 1.12
5/8 x 4 1043472 5,200 103.10 .62 1.25 2.50 .62 2.00 4.00 6.69 1.44
5/8 x 6 1043490 5,200 118.20 .62 1.25 2.50 .62 3.00 6.00 8.69 1.44
5/8 x 8 1043515 5,200 135.10 .62 1.25 2.50 .62 3.00 8.00 10.69 1.44
Rope
Wire
5/8 x 10 1043533 5,200 153.60 .62 1.25 2.50 .62 3.00 10.00 12.69 1.44
5/8 x 12 1043551 5,200 167.10 .62 1.25 2.50 .62 4.00 12.00 14.69 1.44
3/4 x 4-1/2 1043579 7,200 168.60 .75 1.50 3.00 .75 2.00 4.50 7.69 1.69
3/4 x 6 1043597 7,200 184.50 .75 1.50 3.00 .75 3.00 6.00 9.19 1.69
3/4 x 8 1043613 7,200 207.90 .75 1.50 3.00 .75 3.00 8.00 11.19 1.69
3/4 x 10 1043631 7,200 235.00 .75 1.50 3.00 .75 3.00 10.00 13.19 1.69
Cordage
3/4 x 12 1043659 7,200 257.50 .75 1.50 3.00 .75 4.00 12.00 15.19 1.69
3/4 x 15 1043677 7,200 298.00 .75 1.50 3.00 .75 5.00 15.00 18.19 1.69
7/8 x 5 1043695 10,600 270.00 .88 1.75 3.50 .88 2.50 5.00 8.75 2.00
7/8 x 8 1043711 10,600 308.00 .88 1.75 3.50 .88 4.00 8.00 11.75 2.00
7/8 x 12 1043739 10,600 400.00 .88 1.75 3.50 .88 4.00 12.00 15.75 2.00
Securement
1x6 1043757 13,300 421.00 1.00 2.00 4.00 1.00 3.00 6.00 10.31 2.31
Load
1x9 1043775 13,300 468.50 1.00 2.00 4.00 1.00 4.00 9.00 13.31 2.31
1 x 12 1043793 13,300 540.00 1.00 2.00 4.00 1.00 4.00 12.00 16.31 2.31
1 x 18 1043819 13,300 650.00 1.00 2.00 4.00 1.00 7.00 18.00 22.31 2.31
1-1/4 x 8 1043837 21,000 750.00 1.25 2.50 5.00 1.25 4.00 8.00 13.38 2.88
1-1/4 x 12 1043855 21,000 900.00 1.25 2.50 5.00 1.25 4.00 12.00 17.38 2.88
Contractors
1-1/4 x 20 1043873 21,000 1210.00 1.25 2.50 5.00 1.25 6.00 20.00 25.38 2.88
Supply
* Ultimate Load is 5 times the Working Load Limit. Working Load Limit shown is for in-line pull.
Maximum Proof Load is 2 times the Working Load Limit.
Protection
Fall

435

G-277 Shoulder WARNING SEE warning
See WARNING
information
ON PAGES 454
and
INFORMATION
application
on page
- 461.?.
Nut Eye Bolts

■ Fatigue rated at 1-1/2 times the Working Load Limit
at 20,000 cycles.
■ Working Load Limits shown are for in-line pull.
and temperature requirements. Importantly, these bolts
meet other critical performance requirements, including
fatigue life, impact properties and material traceability,
not addressed by ASME B30.26.
■ All Bolts Hot Dip galvanized after threading (UNC).
■ Furnished with standard Hot Dip galvanized,
heavy hex nuts.
Shank Stock Working

Weight
Dia. & No. Load
Per 100
Length Limit
(lbs.)
(in.) (lbs.) *
G-277 A B C D E F G H J
1/4 x 2 1045014 650 6.60 .25 .50 .88 .19 1.50 2.00 2.94 .50 .47
1/4 x 4 1045032 650 9.10 .25 .50 .88 .19 2.50 4.00 4.94 .50 .47
5/16 x 2-1/4 1045050 1,200 12.50 .31 .62 1.12 .25 1.50 2.25 3.50 .69 .56
5/16 x 4-1/4 1045078 1,200 18.80 .31 .62 1.12 .25 2.50 4.25 5.50 .69 .56
3/8 x 2-1/2 1045096 1,550 21.40 .38 .75 1.38 .31 1.50 2.50 3.97 .78 .66
3/8 x 4-1/2 1045112 1,550 25.30 .38 .75 1.38 .31 2.50 4.50 5.97 .78 .66
1/2 x 3-1/4 1045130 2,600 42.60 .50 1.00 1.75 .38 1.50 3.25 5.12 1.00 .91
1/2 x 6 1045158 2,600 56.80 .50 1.00 1.75 .38 3.00 6.00 7.88 1.00 .91
5/8 x 4 1045176 5,200 68.60 .62 1.25 2.25 .50 2.00 4.00 6.44 1.31 1.12
5/8 x 6 1045194 5,200 102.40 .62 1.25 2.25 .50 3.00 6.00 8.44 1.31 1.12
3/4 x 4-1/2 1045210 7,200 144.50 .75 1.50 2.75 .62 2.00 4.50 7.44 1.56 1.38
3/4 x 6 1045238 7,200 167.50 .75 1.50 2.75 .62 3.00 6.00 8.94 1.56 1.38
7/8 x 5 1045256 10,600 225.00 .88 1.75 3.25 .75 2.50 5.00 8.46 1.84 1.56
1x6 1045292 13,300 366.30 1.00 2.00 3.75 .88 3.00 6.00 9.97 2.09 1.81
1x9 1045318 13,300 422.50 1.00 2.00 3.75 .88 4.00 9.00 12.97 2.09 1.81
1-1/4 x 8 1045336 21,000 650.00 1.25 2.50 4.50 1.00 4.00 8.00 12.72 2.47 2.28
1-1/4 x 12 1045354 21,000 795.00 1.25 2.50 4.50 1.00 4.00 12.00 16.72 2.47 2.28
1-1/2 x 15 1045372 24,000 1425.00 1.50 3.00 5.50 1.25 6.00 15.00 20.75 3.00 2.75
* Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Limit.
436

Stainless Steel
Cranes / Jibs
Overhead
Swivels & Links
Eye & Eye Swivel—316 Stainless Steel
Dimensions (in.) WLL WT
Hoists
A (Size) B C D lbs. lbs.
5/32" .43 .50 2 150 .12
3/16" .50 .50 2.31 300 .12
1/4" .56 .56 2.56 600 .12
Services
5/16" .75 .75 3.62 1,100 .29
3/8" .87 1 4.62 1,540 .55
1/2" 1.25 1.31 6 2,640 1.25
5/8" 1.50 1.62 7.37 4,750 2.10
3/4" 1.62 2 8.50 7,000 3.40
7/8" 1.87 2 9.25 8,000 5.02
Engineered
Products
1" 2.50 2.56 11 10,000 8.73
Eye & Jaw Swivel—316 Stainless Steel

Slings
1/4" .50 .43 2.62 600 .14
5/16" .62 .62 3.62 1,100 .33
3/8" .75 .87 4.35 1,540 .63
1/2" 1 1.12 6 2,640 1.40
Hardware
5/8" 1.25 1.37 7.37 4,750 2.36
3/4" 1.50 1.62 8.62 7,000 3.93
Manufacturer recommends the use of thread locking fluid with this type of swivel.
Master Link—316-NM Stainless Steel
Products
Lifting
A (Size) B C lbs. lbs.
3/8 3 1.50 1,500 .35
1/2 5 2.50 2,000 .84
Rope
Wire
5/8 6 3 2,800 1.61
3/4 6.50 3.25 3,750 2.26
1 7 3.50 8,000 4.94
1-1/4 8.75 4.38 11,800 9.65
Each link is individually forged, not welded, and is stamped with size and working load.
Cordage
Be sure all components of your assembly have matched WLL.
Hammerlock—316-NM Stainless Steel

Securement
Size Dimensions (in.) WLL WT

Load
in. A (size) B C D lbs. lbs.

3/16 .29 1.56 .59 .35 1,100 .12
1/4 .32 1.95 .75 .48 2,200 .21
5/16 .38 2.25 .80 .45 2,700 .31
Contractors
3/8 .50 2.95 1.24 .79 4,400 .65

Supply
1/2 .62 3.62 1.37 .80 7,300 1.40

5/8 .80 4.25 1.86 1.20 11,000 3.00
Protection
Fall

437

Stainless Steel
Hooks
Clevis Grab Hook—316 Stainless Steel
in. A B C D lbs. lbs.
1/4 .37 .41 .34 1.83 1,500 .40
5/16 .36 .36 .40 2.08 2,000 .60
3/8 .47 .43 .48 2.55 2,500 1.05
1/2 .54 .50 .60 2.85 3,600 1.84
Working loads are based on gradual pull, not shock loads. Includes removable clevis pin.
Clevis Slip Hook—316 Stainless Steel

in. A B C D lbs. lbs.
1/4 .37 .41 .58 2.57 1,000 .57
5/16 .36 .40 .83 2.73 1,500 .82
3/8 .47 .43 .95 3.04 2,000 1.14
1/2 .54 .50 1.05 3.53 3,000 2.13
Working loads are based on gradual pull, not shock loads. Includes removable latch & clevis pin.
Eye Grab Hook—316 Stainless Steel

1/4 .50 .35 2 1,500 .35
5/16 .56 .43 2.25 2,000 .56
3/8 .50 .50 2.50 2,500 .89
1/2 .65 .66 3.35 3,600 1.51
Working loads are based on gradual pull, not shock loads.
Eye Slip Hook—316 Stainless Steel

1/4 .53 .68 2.54 1,000 .30
5/16 .65 .75 3 1,500 .54
3/8 .71 .80 3.28 2,000 .91
1/2 .94 1.02 4.17 3,000 1.87
5/8 1.25 2.06 6.51 11,000 7
3/4 1.50 2.48 7.82 16,000 12.2
1 2 3.3 10.42 28,000 30
Working loads are based on gradual pull, not shock loads.
438

Stainless Steel
Cranes / Jibs
Overhead
Turnbuckles
Turnbuckle Body—316-NM Stainless Steel
Hoists
A (Size) B (Adjust) C D lbs. lbs.
1/4 4 4.75 .72 500 .15
5/16 4.50 5.5 .82 800 .25
3/8 6 7.13 .97 1,200 .35
1/2 6 7.5 1.16 2,200 .55
5/8 6 7.81 1.38 3,500 .90
Services
3/4 6 8.19 1.69 5,200 1.15
1 6 9 2.31 8,000 2.69
1 12 14.81 2.31 8,000 4.17
1-1/4 12 15.13 2.62 12,500 5.90
Meets WLL & dimensions of ASTM Specification F1145-92, Type1.
Engineered
Products
Turnbuckle Eye & Eye—316-NM Stainless Steel
A (Size) B (Adjust) C D lbs. lbs.
1/4 4 8 .33 500 .30
5/16 4.50 9.25 .41 800 .50
Slings
3/8 6 11.5 .5 1,200 .85
1/2 6 13 .75 2,200 1.30
5/8 6 14.5 .87 3,500 2.30
3/4 6 16.25 1 5,200 3.50
1 6 20 1.38 8,000 8.85
1 12 25.5 1.38 8,000 10.91
Hardware
1-1/4 12 28.38 1.71 12,500 17.60
Meets WLL and dimensions of ASTM Specification F1145-92, Type1, Class D.
Turnbuckle Jaw & Eye—316-NM Stainless Steel
Products
Dimensions (inches) WLL WT
Lifting
A (Size) B (Adjust) C D E lbs. lbs.
1/4 4 7.88 .45 .44 500 .35
5/16 4.50 9.25 .50 .5 800 .60
3/8 6 11 .51 .56 1,200 .80
1/2 6 12.5 .71 .63 2,200 1.55
5/8 6 14 .87 .75 3,500 2.69
Rope
Wire
3/4 6 15.63 .98 1 5,200 4.00
1 6 19 1.35 1.25 8,000 9.66
1 12 25 1.36 1.25 8,000 11.79
1-1/4 * 12 27.5 1.37 1.88 10,000 19.96 * Jaw for size 1-1/4" features a
Meets WLL and dimensions of ASTM Specification F1145-92, Type1, Class H. round pin with cotter.
Cordage
Turnbuckle Jaw & Jaw—316-NM Stainless Steel
Dimensions (inches) WLL WT
A (Size) B (Adjust) C D E lbs. lbs.
Securement
1/4 4 7.75 .25 .44 500 .45

5/16 4.50 9 .25 .5 800 .65
Load
3/8 6 10.63 .31 .56 1,200 .90

1/2 6 12 .38 .63 2,200 1.60
5/8 6 13.5 .5 .75 3,500 3.05
3/4 6 15 .63 1 5,200 4.25
1 6 18 .88 1.25 8,000 10.59
Contractors
1 12 24 .88 1.25 8,000 12.66

Supply
1-1/4 * 12 26.63 1.13 1.88 12,500 22.32

1-1/2 * 12.25 28.95 1.36 2.19 17,000 31.04 * Jaw for size 1-1/4" features a
Meets WLL and dimensions of ASTM Specification F1145-92, Type1, Class H. round pin with cotter.
Protection
Fall

439

G-Link™ Synthetic WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Sling Connector
US Patent # 5,651,573 (G-Link)
Product Features:
■ Couples web, round or Twin-Path® slings with

hardware (oblongs or hooks).
■ Splices two slings into longer length.
■ Connects two slings with oblong and two hooks
into bridle sling.
■ Allows sling to be used as sliding choker sling.
■ Two G-Link™ connectors used together will double
the rated capacity of one G-Link™ connector.
■ Conforms with ASME B30.9 web and round sling
specifications.
Vertical Choker Sling

Model Rated Rated Weight
Number Size (lbs.)
Capacity Capacity
(in.)
(tons) (tons)
SC200L 2-1/2 2 2 2
SC300L 5 3 3 3-1/2
SC400L 7-1/2 4 4 7
SC500L 15 8 5 15
SC600L 25 12 6 29
Dimensions (in.)
Model
A B C D E F G H J O R T W
SC200L 2 5/8 1-1/8 5/8 1-1/3 1-15/16 1 5 1-13/16 1/2 .5 .5 3.5
SC300L 3 11/16 1-1/4 11/16 2-1/4 2-7/16 1-1/4 6.62 2-1/2 9/16 .75 .75 5
SC400L 4 13/16 1-3/8 13/16 2-1/2 2-7/8 1-3/8 7.5 2-3/4 3/4 .75 1 6
SC500L 5 1-1/16 2 1-1/16 3 3-3/4 2 9.75 3-3/4 1 1 1.25 8
SC600L 6 1-1/4 2-1/4 1-1/4 4 5 2-1/4 12.5 4-3/4 1-1/4 1 1.5 9.38
Connect Connect Connect Choker

Hook to Sling Oblong to Sling Two Slings Hook
440

Proof Coil Chain— WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Grade 30
Quick-ship from stock! Working Nominal Inside Link Weight Per

Chain Size
Hoists
Load Limit Dimension (inches) 100 Ft.
inches decimals lbs. Length Width lbs.
3/16 .218 800 .95 .40 38
1/4 .276 1,300 1.00 .47 66
Grade 30 5/16 .327 1,900 1.10 .50 98
Services
Proof Coil Chain— 3/8 .390 2,650 1.23 .62 144
embossed: G30 and date codes; 7/16 .468 3,700 1.37 .75 210
available in self-colored, zinc plated 1/2 .531 4,500 1.50 .81 278
and hot galvanized. 5/8 .656 6,900 1.87 1.00 422
Engineered
3/4 .787 10,600 2.12 1.12 628
Products
1 1.031 17,900 2.75 1.50 1,069
Slings
Hardware
Products
Lifting
Rope
Wire
Cordage
Securement
Load
Contractors
Supply
Protection
Fall

441

Carbon Chains WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Coil Chain—Twist Link

Diameter Link Weight Working
Wire Dimensions Links Per 100 Ft. Load Limit
Trade
Inside Inside Per
Number Fractional Decimal
Length Width Foot lbs. lbs.
(in.) (in.)
(in.) (in.)
4 1/8 .120 1-3/32 3/16 11 10 195
3 9/64 .135 1-9/64 13/64 10-1/2 12 240
2 5/32 .148 1-9/64 7/32 10-1/2 16 295
1/0 11/64 .177 1-15/64 17/64 9-3/4 24 415
2/0 3/16 .192 1-15/64 19/64 9-3/4 28 495
4/0 7/32 .218 1-11/32 21/64 9 36 635
5/0 1/4 .250 1-15/32 3/8 8-1/8 48 835
May be ordered bright (polished), zinc plated or hot galvanized. Packed 100 feet per carton.
WARNING: This chain is not for overhead lifting—working load limit is not to be exceeded!
Coil Chain—Straight Link

Trade
Inside Inside Per
(in.) (in.)
(in.) (in.)
4 1/8 .120 1-7/64 13/64 10-7/8 10 205
3 9/64 .135 1-11/64 15/64 10-1/4 13 255
2 5/32 .148 1-11/64 17/64 10-1/8 15 310
1/0 11/64 .177 1-1/4 5/16 9-5/8 23 440
2/0 3/16 .192 1-17/64 11/32 9-1/2 27 520
4/0 7/32 .218 1-25/64 3/8 8-5/8 35 670
5/0 1/4 .250 1-33/64 7/16 7-7/8 46 880
May be ordered bright (polished), zinc plated or hot galvanized. Packed 100 feet per carton. Also available on reels or in 10 foot polybags.
Machine Chain—Twist Link

Trade
Inside Inside Per
(in.) (in.)
(in.) (in.)
4 1/8 .120 33/64 12/64 23 13 205
3 9/64 .135 9/16 13/64 21-1/2 16 255
2 5/32 .148 37/64 7/32 21 20 310
1/0 11/64 .177 47/64 17/64 17-1/2 29 440
2/0 3/16 .192 23/32 9/32 16-1/2 34 520
4/0 7/32 .218 57/64 5/16 13-1/2 44 670
5/0 1/4 .250 1 3/8 12 57 880
May be ordered bright (polished), zinc plated or hot galvanized. Packed 100 feet per carton. Also available on reels.
442

Carbon Chains (Continued) WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Machine Chain—Straight Link
Hoists
Trade
Inside Inside Per
(in.) (in.)
(in.) (in.)
Services
4 1/8 .120 35/64 7/32 22 12 215
3 9/64 .135 19/32 15/64 20-1/4 15 270
2 5/32 .148 39/64 17/64 19-3/4 19 325
1/0 11/64 .177 47/64 5/16 16-1/4 27 465
2/0 3/16 .192 25/32 11/32 15-1/4 32 545
Engineered
4/0 7/32 .218 61/64 3/8 12-1/2 40 700
Products
5/0 1/4 .250 1-5/64 7/16 11-1/4 54 925
May be ordered bright (polished), zinc plated or hot galvanized. Packed 100' per carton. Also available on reels.
Passing Link Chain
Slings
Size Link Weight Per Working
Material Dimensions Links 100 Ft. Load Limit
Trade
Inside Inside Per
Number
Hardware
(in.) Length Width Foot lbs. lbs.
(in.) (in.)
2/0 3/16 7/8 15/32 13-5/8 33 450
4/0 7/32 7/8 1/2 13-5/8 43 600
An electrically welded steel chain, the links of which are designed with the inside width greater than twice the
Products
Lifting
thickness of the material, thus allowing the two adjacent links to pass in any link, reducing any tendency to kink.
May be ordered bright (polished) or zinc plated. Packed 100 feet per carton. 2/0 size also available on
120 foot reels and 200 foot pails.
Double Loop Chain
Rope
Wire
Material Links Weight Per Working
Trade Feet Per Inside 100 Ft. Load Limit
Diameter Per
Number Carton Length (in.)
(in.) Foot lbs. lbs.
Cordage
5 100 .062 .92 13 3-1/2 55
4 100 .072 1.00 12 4-1/2 70
3 100 .080 1.10 11 5-3/4 90
2 100 .092 1.33 9 7-1/2 115
1 100 .105 1.50 8 10 155
Securement
1/0 100 .120 1.71 7 13 200

2/0 100 .135 1.71 7 17 255
Load
3/0 100 .148 2.18 5.5 20 305

4/0 100 .162 2.18 5.5 23 365
8/0 100 .225 2.90 4.1 48 705
Applications: A general purpose chain, often used for playground equipment, animal leaches, fixture, swing or hammock
Contractors
suspensions, boats and gates. Description: Standard material is mild steel. Finishes include bright or zinc plated.
Supply
Packing: Standard packaging is 100 feet per carton. Sizes 4 through 4/0 also available on reels.
Protection
Fall

443

ON PAGES 454 - 461.
Single Loop Chain

Material Inside Links Weight Per Working
Trade Feet Per 100 Ft. Load Limit
Diameter Length Per
Number Carton
(in.) (in.) Foot lbs. lbs.
2 100 .091 1.08 11.1 10 155
1/0 100 .120 1.29 9.3 17 265
2/0 100 .135 1.48 8.1 22 340
3/0 100 .148 1.63 7.4 26 405
4/0 100 .162 1.80 6.7 31 485
5/0 100 .177 2.15 5.6 35 580
Applications: Ideal for sprocket wheel or valve wheel, overhead door, ventilator and machinery chains or applications
requiring greater strength than double loop chain. Description: Standard material is mild steel; also available in brass.
Finishes include bright or zinc plated. Packing: Standard packaging is 100 feet per carton. Also available on reels.
Single Jack Chain

Material Inside Links Weight Per Working Load
Trade Feet Per 100 Ft. (lbs.) Limit (lbs.)
Diameter Length Per
Number Carton
(in.) (in.) Foot Steel Brass Steel Brass
18 100 .047 .39 31 1-3/4 2 5 4
16 100 .062 .50 25 3 3-1/4 10 8
14 100 .080 .63 19 5 5-1/4 16 11
12 100 .105 .75 16 8-3/4 9-1/4 29 20
10 100 .135 .93 13 14-3/4 15-1/4 43 34
8 100 .162 1.09 11 20-1/2 22 60 43
Applications: A light general utility chain often used to suspend light fixtures or novelties.
Description: Standard material is mild steel; also available in brass. Finishes include bright or zinc plated.
Packing: Standard packaging is 100 feet per carton. Also available on reels.
Safety Chain / Brass

Stock Inside Links Weight Per Working
Thickness Length Per
Number Carton
2/0 100 .018 .44 27 2-1/4 23
1/0 100 .023 .50 24 2-1/2 30
1 100 .028 .60 20 3-1/4 40
3 100 .037 .75 16 6-1/4 75
Applications: A light general utility chain often used to suspend light fixtures or novelties.
Description: Standard material is mild steel; also available in brass. Finishes include bright or zinc plated.
Packing: Standard packaging is 100 feet per carton. Also available on reels.
444

ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Sash Chain
Stock Inside Links Weight Per Working
Hoists
Thickness Length Per
Number Carton
8 100 .035 .57 21 4 75
25 100 .042 .57 21 5 94
Services
30 100 .028 .57 21 5-1/2 80
35 100 .035 .57 22 7 105
40 100 .042 .55 22 8 140
45 100 .050 .55 22 9-1/2 175
50 100 .062 .62 19.5 13 225
Engineered
Products
Applications: Ideal for sprocket wheel or valve wheel, overhead door, ventilator and machinery chains or applications
requiring greater strength than double loop chain. Description: Standard material is mild steel; also available in brass.
Finishes include bright or zinc plated. Packing: Standard packaging is 100 feet per carton. Also available on reels.
Special Well Chain
Slings
Material Approx. Weight Working Load
Trade Feet Per Carton Limit
Diameter
Number Per Reel
(in.) lbs. lbs.
Hardware
2/0 250 .135 .57 255
Applications: Primarily used with windlass and bucket to raise water from wells or cisterns. Also, considered a
general utility chain. Description: mild steel chain, zinc plated. Finishes include bright, copper plated and zinc plated.
Packing: 250 feet per carton.
Products
Lifting
Hooks WARNING SEE WARNING INFORMATION

ON PAGES 454 - 461.
Rope
Wire
Grade 30—Eye Grab Hook
Weight Self Electro-
Chain Pieces
WLL Per Colored Galv.
Size Per
Cordage
Carton Part Part
Carton
in. lbs. lbs. Number Number
1/4 2,600 10 3 6460-205-00 6460-205-04
5/16 3,900 10 5 6460-305-00 6460-305-04
3/8 5,400 10 8 6460-405-00 6460-405-04
Securement
1/2 9,200 10 20 6460-605-00 6460-605-04

Load
Winch Hook with Latch

Chain Pieces Electro-Galv.
Contractors
WLL Weight
Size Per Part
Supply
Grade 30— Winch Hook

in. lbs. Carton lbs. Number
Eye Grab Hook with Latch
3/4 1,875 1 48 6497-300-04
Protection
Fall

445

Proof Coil—Grade 30 WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
■ A general light purpose chain

ideal for most applications
requiring a light-duty steel chain
■ Available in self-colored, electro-
galvanized, hot galvanized and
power coated (by special order)
G30 Specifications
Weight
Chain Material Inside Inside
WLL Per
Size Dia. Length Width
100 Ft.
in. lbs. lbs. in. in. in.
1/8 * 400 21 .16 .90 .27 Round Pails
3/16 800 37 .21 .95 .39
1/4 ** 1,300 55 .275 1.24 .46 Weight Self Electro- Hot
1/4 1,300 59 .275 1.02 .50 Chain Feet Per Colored Galv. Galv.
5/16 ** 1,900 79 .33 1.30 .49 Size Per
5/16 1,900 100 .33 1.15 .49 Pail Part Part Part
Pail
3/8 ** 2,650 115 .397 1.45 .60 in. lbs. Number Number Number
3/8 2,650 145 .397 1.30 .60 1/8 * 500 105 2113-502-00 2113-502-04 2113-502-06
1/2 4,500 264 .52 1.56 .81 3/16 250 95 2116-601-00 2116-601-04 2116-601-06
5/8 6,900 393 .63 1.87 1 1/4 ** 141 89 2119-601-00 2119-601-04 2119-601-06
3/4 * 10,600 628 .78 2.71 1.04 1/4 141 98 2119-503-00 2119-503-04 2119-503-06
5/16 ** 92 84 2123-601-00 2123-601-04 2123-601-06
* Imported 5/16 92 92 2123-503-00 2123-503-04 2123-503-06
** Long Link--chain that has a reduction in weight and cost 3/8 ** 63 86 2126-601-00 2126-601-04 2126-601-06
without comprising strength 3/8 63 92 2126-503-00 2126-503-04 2126-503-06
1/2 36 95 2133-501-00 2133-501-04 2133-501-06
Drums * Imported
** Long Link
Weight Self Electro- Hot
Chain Feet Per Colored Galv. Galv. Square Pails
Size Per Drum Part Part Part
Drum
in. lbs. Number Number Number Weight Self Electro- Hot
2,000 430 2113-561-00 2113-561-04 2113-561-06 Chain Feet
1/8 * Per Colored Galv. Galv.
1,000 215 2113-562-00 2113-562-04 2113-562-06 Size Per Pail Part Part Part
1,600 602 2116-642-00 2116-642-04 2116-642-06 Pail
3/16 in. lbs. Number Number Number
800 301 2116-641-00 2116-641-04 2116-641-06
800 450 2119-643-00 2119-643-04 2119-643-06 3/16 175 67 2116-403-00 2116-403-04 2116-403-06
1/4 ** 2119-606-00 2119-606-04 2119-606-06
400 252 2119-644-00 2119-644-04 2119-644-06 1/4 ** 100 63
800 482 2119-543-00 2119-543-04 2119-543-06 5/16 ** 70 64 2123-600-00 2123-600-04 2123-600-06
1/4 2126-600-00 2126-600-04 2126-600-06
400 241 2119-544-00 2119-544-04 2119-544-06 3/8 ** 45 61
550 446 2123-643-00 2123-643-04 2123-643-06 1/2 25 66 n/a 2133-403-04 n/a
5/16
275 250 2123-644-00 2123-644-04 2123-644-06
550 560 2123-543-00 2123-543-04 2123-543-06 ** Long Link
5/16 **
275 280 2123-544-00 2123-544-04 2123-544-06
400 470 2126-643-00 2126-643-04 2126-643-06
3/8
200 270 2126-644-00 2126-644-04 2126-644-06 Reels
400 590 2126-543-00 2126-543-04 2126-543-06
3/8 ** Weight Self Electro-
200 295 2126-544-00 2126-544-04 2126-544-06 Chain Reel
2133-543-00 2133-543-04 2133-543-06
Feet Per
1/2
200 538
Size Width Colored Galv.
100 269 2133-544-00 2133-544-04 2133-544-06 Per Reel Part Part
150 590 2139-543-00 2139-543-04 2139-543-06 Reel
5/8
75 295 2139-544-00 2139-544-04 2139-544-06 in. in. in. Number Number
100 628 2143-541-20 n/a 2143-541-56 1/4 ** 100 63 12-1/8" 2119-623-04 2119-623-06
3/4 * 5/16 ** 70 64 12-1/8" 2123-632-04 2123-632-06
50 311 2143-544-20 n/a 2143-544-56
3/8 ** 45 62 12-1/8" 2126-633-04 n/a
* Imported
** Long Link ** Long Link
446

Proof Coil—Grade 30 WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
(Continued)
G30 / G43 Clevis Grab Hook
Weight Electro-
Chain
Hoists
Pieces Per Per Galv.
Size
Carton Carton Part
in. lbs. Number
1/4 10 4 6470-205-04
5/16 10 7 6470-305-04
Services
3/8 10 10 6470-405-04
7/16 10 15 6470-505-04
1/2 10 21 6470-605-04
G30 / G43 Clevis Slip Hooks with Latch
Engineered
Products
Weight
Chain Electro-Galv.
Pieces Per Per
Size Part
Carton Carton
Number
in. lbs.
G30 / G43 G30 / G43
1/4 10 5 6495-205-04
Clevis Clevis
Slings
5/16 10 8 6495-305-04
3/8 10 13 6495-405-04 Grab Hook Slip Hook
7/16 10 21 6490-551-04 With Latch
1/2 10 29 6490-605-04
Hardware
Lockdown Chain WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
■ Square heat treated links make it very difficult to

cut with conventional bolt cutters
Products
■ Perfect for construction equipment, trailers, ATVs,
Lifting
watercrafts and all your other valuables.
■ Also available for this lockdown chain is a special
lock, part number: 8204-100-04. Contact manufacturer
if multiple locks are needed that are keyed alike.
Rope
Wire
Specifications
Weight
Chain Material Inside Inside
WLL Per
Size Dia. Length Width
100 Ft.
Cordage
mm (in.) lbs. lbs. in. in. in.
10 mm (3/8) n/a 160 .66 1.49 .622
13 mm (1/2) n/a 264 1.10 1.742 .807 Securement
Drums
Load
Chain Weight Per

Size Feet Per Drum Part
Drum Number
mm (in.) lbs.
Contractors
10 mm (3/8) 300 481 1970-543-34

Supply
10 mm (3/8) 100 160 1970-512-34

13 mm (1/2) 200 562 1970-543-34
13 mm (1/2) 100 283 1973-544-34
Protection
Fall

447

Weldless Chain WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Decorator Chain
■ A light metal chain with oblong loop used in
the suspension of household items
Specifications
Chain Working Weight Per Material
Size Load Limit 100 Ft. Diameter
Trade Size lbs. lbs. in.
#11 45 14 .13
Reels
Chain Feet Weight Reel
Standard
Size Per Per Reel Width Part Number
Finish
Trade Size Reel lbs. lbs.
Black #11 50 8 3-5/8 3285-521-42
Polished Brass #11 50 8 3-5/8 3285-521-41
Antique Brass #11 50 8 3-5/8 3285-521-43
White #11 50 8 3-5/8 3285-521-48
Plumber’s Chain (Solid Brass) ■ A flat metal stamped chain made of brass.
Specifications
Chain Working Weight Per Material
Size Load Limit 100 Ft. Diameter
Trade Size lbs. lbs. in.
1/0 35 3 .023
Carton Reels
Chain Feet Weight Chain Feet Weight Reel
Electro-Galv. Size Per Reel Width Electro-Galv.
Size Per Per Carton Per
Part Number Part Number
Trade Size Carton lbs. Trade Size Reel lbs. in.
1/0 100 3 4836-512-10 1/0 200 5 3-5/8 4836-527-10
■ A chain made of light wire and used in the suspension of

Double Jack Chain household or light industrial applications
Specifications
Working
Working Weight
Chain Load Limit Material
Load Limit Per
Size Electro- Diameter
Brass 100 Ft.
Galv.
Trade Size lbs. lbs. lbs. in.
#16 8 11 4 .062
Reels
Chain Feet Weight Reel
Brass Electro-Galv.
Size Per Per Reel Width
Part Number Part Number
Trade Size Reel lbs. in.
#16 200 9 3-5/8 4319-527-10 4319-527-04
448

S-247
Cranes / Jibs
Overhead
Double Clevis Link
■ All pins Alloy Steel — Quenched and Tempered.
■ Body is forged and heat treated carbon steel.
■ Designed for linking all popular sizes of
Hoists
Crosby Spectrum 3® and Spectrum 4® chain to
rings, end links, eye hooks, pad eyes, tractor
eye bolts, etc.
Services
Engineered
Products
Stock No. Dimensions (in.)
Size Load Limit Each
in. S-247 lbs. lbs. A B C D E F G H L N P R
1/4 1013021 2,600 .38 .50 .75 .50 .31 .38 .75 1.00 .81 2.81 1.38 1.66 1.50
5/16 - 3/8 1013049 5,400 .81 .56 1.00 .63 .44 .47 1.00 1.19 1.00 3.53 1.75 2.25 1.91
Slings
7/16 1013067 7,200 1.25 .69 1.13 .69 .56 .59 1.09 1.31 1.19 4.06 2.00 2.50 2.19
1/2 1013085 9,200 1.56 .81 1.25 .75 .63 .68 1.25 1.44 1.31 4.53 2.25 2.75 2.47
S-249
Hardware
Twin Clevis Link
■ Available in three popular sizes.
Products
■ Body is forged and heat treated carbon steel.
Lifting
■ All pins Alloy Steel — Quenched and Tempered.
■ Twin Clevis design provides a variety of uses and
can be used with Crosby Spectrum 3®, Spectrum 4®
and Spectrum 7® chain.
Rope
Wire
Stock No. Dimensions (in.)
Size Load Limit Each
Cordage
in. S-249 lbs. lbs. A B C D F G H K
1/4 - 5/16 1012861 4,700 .31 .47 2.50 1.56 .38 1.31 .43 .94 .50
3/8 1012889 6,600 .44 .53 2.81 1.81 .44 1.53 .50 1.00 .56
7/16 - 1/2 1012905 11,300 .98 .65 3.62 2.31 .56 1.91 .63 1.31 .81
Securement
Load
Contractors
Supply
Protection
Fall

449

Clevis Link WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
■ Drop-forged from special bar quality steel.

■ Heat-treated for greater strength and increased
wear characteristics.
■ Metric-marked.
■ Clear protective finish resists rust and provides
cleaner handling.
■ For rigging not involving overhead lifting.
Chain Working Approx.

Dimensions (in.) Factory
Size Load Limit Weight Each
Pack
in. lbs. A B C D E F lbs.
5/16 4,400 2-1/8 3-1/16 9/16 3-17/64 5-15/32 25/64 10 .94
3/8 6,600 2-1/8 3-3/16 21/32 3-27/64 5-19/32 15/32 10 1.19
Quick Link
Chain Working Inside Inside
Standard Gap
Size Load Limit Width Length
Pack
in. lbs. in. in. in.
1/8 220 20 13/64 25/64 1-9/64
3/16 615 20 1/4 1/2 1-1/2
1/4 880 20 9/32 9/16 1-3/4
5/16 1,540 20 3/8 11/16 2-5/16
3/8 1,980 10 7/16 3/4 2-7/16
1/2 3,300 10 19/32 15/16 3-3/16
Applications: Used as a repair link, connecting link or attaching device.
Description: Zinc-plated, not heat-treated. Use only with chain of equal or lower working load limit.
Not to be used for load securement (tie-down).
Repair Link
Trade Working Inside Inside Approx.
Size Load Limit Pieces Per Width Length Weight Each
Carton
in. lbs. in. in. lbs.
3/16 x 1 240 100 1 25/64 .035
7/32 x 1-1/4 250 50 1-1/4 1/2 .055
1/4 x 1-1/4 400 50 1-1/4 9/16 .075
1/4 x 2 400 50 2 11/16 .105
5/16 x 1-1/2 950 50 1-1/2 3/4 .145
5/16 x 2 1,000 50 2 15/16 .170
3/8 x 1-5/8 1,250 50 1-5/8 3/4 .230
3/8 x 2 1,250 50 2 3/4 .240
Applications: A temporary repair link also used to couple light attachments.
Description: A mild steel, available with bright, hot galvanized or zinc-plated finishes.
Not to be used for load securement (tie-down).
450

Cold Shut WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
Cranes / Jibs
Overhead
Trade Working Load Inside Inside Approx.
Hoists
Size Limit Width Length Weight Each
in. lbs. in. in. lbs.
3/16 525 15/16 5/16 .03
1/4 800 1 3/8 .05
5/16 1,300 1-3/16 7/16 .11
Services
3/8 1,900 1-5/16 1/2 .17
7/16 2,650 1-1/2 9/16 .27
1/2 3,500 1-9/16 3/4 .39
5/8 4,500 2-1/8 7/8 .77
3/4 6,900 2-11/16 1 1.28
Engineered
Applications: A temporary repair link, use one size larger than proof coil chain (grade 30) with which it
Products
is to be used. Also used to couple light attachments. Description: Low carbon steel, self-colored or
zinc-plated finish. Not to be used for load securement (tie-down).
Welded Ring
Slings
Material Size & Working Approx.
Pieces Per
Diameter Load Limit Weight Each
Carton
in. lbs. lbs.
Hardware
3/16 x 1-1/4 200 25 0.0325
3/16 x 2 150 25 0.0525
1/4 x 1-1/2 450 25 0.775
1/4 x 2 350 25 0.0975
5/16 x 2 600 25 0.16
3/8 x 2 900 25 0.2325
1/2 x 2-1/2 1,300 10 0.6
Products
Lifting
5/8 x 4 1,700 10 1.45
Applications: A chain attachment for general use.
Description: Low carbon steel. Finishes are bright or zinc-plated.
“S” Hook
Rope
Wire
Working Inside Throat Approx.
Hook No. Load Limit Wire Size Length Opening Weight Per 100
Cordage
lbs. in. lbs. lbs.
20 16 .080 27/32 5/32 1/4
21 16 .080 11/16 5/32 1/4
40 42 .134 1 5/16 1
60 75 .192 1-11/16 7/16 3-3/4
61 100 .204 1-5/8 7/16 3-7/8
Securement
62 * 120 .175 1-3/8 9/16,1/4 2-1/2

Load
72 * 95 .225 1-1/2 5/16,3/8 4-3/4

80 130 .250 1-3/4 7/16 6-1/4
Fig. 1
81 160 .250 2-1/2 7/16 8
84 * 190 .250 1-25/32 5/16,1/2 6-1/4
100 290 .312 2-1/4 7/16 11-3/4
Contractors
120 410 .375 2-3/8 1/2 19-1/2

Supply
Applications: Used to attach various accessories to chain. Low working load limits only. * Figure 2 Fig. 2
Description: Mild steel, bright, zinc-plated. Packaging: 50 pieces in a carton.
Protection
Fall

451

S Hooks WARNING SEE WARNING INFORMATION
ON PAGES 454 - 461.
“S” hooks may be used for joining light weight chain and
assemblies such as hanging planters. Unequal eye “S” offer
greater flexibility in the rand of sizes required for joining.
Trailer Bulk S Hooks

Working Minimum Weight
Chain Electro- With Wire
Load Ultimate Class Pieces Per
Size Galv. Latch Part
Limit Tensile of Per Carton
Part Number
(dia. x Trailer Carton
lbs. lbs. lbs. Number (Bulk Pack)
length)
3/8" x 2-7/8" 750 3,000 No. 1 10 2.5 6495-511-33 6495-411-83
13/32" x 2-7/8" 875 3,500 No. 2 10 3 6495-718-33 6495-418-83
7/16" x 13/32" 1,250 5,000 No. 3 10 4 6495-716-33 6495-416-83
17/32" x 3-1/2" 1,900 7,600 No. 4 10 6 6495-719-33 6495-419-83
S Hooks (Light-Duty—Not for Trailer Assemblies)

Equal Eye
Weight Weight
Material Inside Pieces
Trade WLL Per 100 Per Part
Size Length Per
Number Pieces Carton Number
Carton
lbs. in. lbs. lbs. lbs.
11 .12 1 40 1.5 1 6450-116-04
7 .177 1-1/8 75 2.25 1.5 6450-076-04 Equal Eye
19 .192 1-3/4 75 3.5 50 2 6450-196-04
25 .25 1-3/4 200 8 4 6450-256-04
375 375 2-29/64 270 19.5 10 6453-756-04
Un-Equal Eye
148 .148 1-5/32 40 2 1 6451-486-04
192 .192 1-15/16 50 4 2 6451-926-04
50
250 .25 2 105 8 4 6452-506-04 Un-Equal Eye
312 .312 2-25/64 185 14.5 7.5 6453-126-04
Snap Links
Weight Electro-
Size A B C Pieces Per
Trade Galv.
Per
Number Carton Part
Carton
lbs. in. in. in. lbs. Number
1/4 15/64 1-57/64 1/4 10 .64 6751-163-17
5/16 5/16 2-35/64 7/16 10 1.5 6751-203-17
2450Z
3/8 25/64 3-3/16 35/64 10 2.9 6751-243-17
1/2 15/32 4-37/42 3/4 5 3 6751-325-17
G70 Double Clevis—Twin Link

Caution: Not be used for
Working Weight Electro-
Chain Pieces playground equipment or backyard
Load Per Galv.
Size Per swing sets or other applications
Limit Carton Part
Carton involving the safety of persons
in. lbs. lbs. Number
1/4 x 5/16 4,700 10 3 6749-105-28 or property. Observe working
3/8 6,600 10 5 6749-205-28 load limits.
7/16 x 1/2 11,300 5 6 6749-304-28
452

G-334 / S-334
Cranes / Jibs
Overhead
Pear Shape “Missing Link”®
Replacement Links
Hoists
■ Has larger inside dimensions making it easier to
attach hooks or other fittings to the chain.
■ An exclusive Crosby product.
■ After making connections, rivets must be peened.
Services
Working
Chain Weight
Stock No. Load Dimensions (in.)
Size Per 100
Limit
Engineered
Products
G-334 S-334
in. lbs. * lbs. A B C D E F G H L
Galv. S.C.
3/8 1013432 1013441 1,850 25.00 .41 2.00 .56 .81 2.94 1.63 .47 1.38 .81
1/2 1013450 1013469 3,300 50.00 .50 2.50 .69 1.00 3.63 2.00 .56 1.69 1.00
5/8 1013478 1013487 5,000 75.00 .63 2.75 .81 1.06 4.00 2.38 .63 2.06 1.13
3/4 1013496 1013502 7,100 125.00 .75 3.13 1.00 1.13 4.75 2.75 .81 2.50 1.25
Slings
7/8 1013511 1013520 9,600 200.00 .88 3.69 1.25 1.38 5.56 3.25 .94 3.00 1.50

WARNING: Not Suitable for use with Grade 80 or Grade 100 chain and chain slings used in overhead lifting.
Hardware
G-335 / S-335
“Missing Link”®
Replacement Links
Products
Lifting
Meets or exceeds the performance requirements of Federal ■ Forged Steel — Quenched and Tempered.
Specifications RRC-27lD, Type II, except for those provisions ■ Integral rivets join the two halves.
required of the contractor. ■ After making connections, rivets must be peened.
Rope
Wire
Working
Chain Weight
Stock No. Load Links Dimensions (in.)
Size Per 100
Limit Per
G-335 S-335 Box
in. lbs. * lbs. A B C D E F G
Cordage
Galv. S.C.
** 3/16 1013094 1013101 800 20 2.50 .25 .69 .34 .34 1.19 .78 .28
** 1/4 1013110 1013129 1,325 10 6.25 .28 .88 .44 .44 1.50 1.00 .31
** 5/16 1013138 1013147 1,950 10 12.50 .34 .94 .47 .47 1.69 1.16 .38
3/8 1013156 1013165 2,750 10 20.00 .41 1.13 .56 .56 2.06 1.38 .47
Securement
7/16 1013174 1013183 3,625 10 27.50 .47 1.28 .59 .59 2.34 1.53 .53
Load
1/2 1013192 1013209 4,750 10 37.50 .53 1.47 .66 .66 2.66 1.72 .59
5/8 1013236 1013245 7,250 10 72.50 .66 1.81 .78 .81 3.31 2.09 .75
3/4 1013254 1013263 10,250 10 122.50 .78 2.13 .94 1.06 3.88 2.50 .88
7/8 1013272 1013281 12,000 Bulk 175.00 .91 2.50 1.13 1.13 4.50 2.94 1.00
†1 1013290 1013307 15,500 Bulk 250.00 1.03 2.75 1.25 1.25 5.00 3.31 1.13
Contractors
Supply
* Ultimate Load is 4 times the Working Load Limit. ** Rivets Only - No interlocking lugs.
† Has reinforced rivet holes. All sizes have countersunk rivet holes.
WARNING: Not Suitable for use with Grade 80 or Grade 100 chain and chain slings used in overhead lifting.
Protection
Fall

453

Rigging Hardware
Product Warnings
454

Engineered Shackles, Kulkoni
Rings & Hooks Warnings Shackles
Warnings
WARNING
WARNING
DO NOT EXCEED RATED CAPACITY.
■ Failure to follow warnings and instructions may result in
Can fail if damaged, misused or overloaded. serious injury or death.
Inspect before use. Use only if trained. ■ Working Load Limit: This is the term used throughout
DEATH or INJURY can occur from improper the catalog. There are, however, other terms used in the
use or maintenance. industry which are interchangeable with the term Working
Load Limit. These are: WLL, SWL, Safe Working Load,
Rated Load Value, Resulting Safe Working Load, and
Rated Capacity.
NEVER EXCEED THE WORKING LOAD LIMIT.
The Working Load Limit is the maximum load which should

ever be applied to a product, even when the product is
new and when the load is uniformly applied - straight line
Skookum pull only. Avoid side loading. All catalog ratings are
Shackles

based upon usual environmental conditions, and
consideration must be given to unusual conditions
Warnings

such as extreme high or low temperatures, chemical
solutions or vapors, prolonged immersion in salt water, etc.
Such conditions or high-risk applications may necessitate
reducing the Working Load Limit.
For complete warning and application
information, see The Ulven Companies at Working Load Limit will not apply if product has been
welded or otherwise modified.
www.ulvencompanies.com
■ Matching of Components: Components must match.
Make certain that components such as hooks, links or
shackles, etc. used with wire rope (or chain or cordage) are
of suitable material size and strength to provide adequate
safety protection. Attachments must be properly installed
and must have a Working Load Limit at least equal to the
RUD

product with which they are used. Remember: Any chain is
only as strong as its weakest link.
Load Rings ■ Raised Loads: Keep out from under a raised load.
Warnings

Take notice of the recommendation from the Safety Council
Accident Prevention Manual concerning all lifting
operations: "All employees working at cranes or hoists or
assisting in hooking or arranging a load should be
For complete warning and application instructed to keep out from under the load. From a safety
information, see The RUD Group at standpoint, one factor is paramount:
www.rud.com Conduct all lifting operations in such a manner, that if there
were an equipment failure, no personnel would be injured.
This means keep out from under a raised load and keep out
of the line of force of any load."
■ Do not operate a load over people.
Do not ride on loads.
■ Shock Loads: Avoid impacting, jerking or swinging of
load as the Working Load Limit could be exceeded and the
Working Load Limit will not apply. A shock load is generally
significantly greater than the static load.
AVOID SHOCK LOADS.

information, see Kulkoni Inc. at
www.kulkoni.com
455

Swivel Hoist Rings Hoist Hooks
Warnings Warnings
WARNING
■ Crosby 319N, 320N or 322N hook with an S-4320 latch
WARNING attached and secured with cotter pin or bolt, nut and pin;
■ Loads may slip or fall if proper Hoist Ring assembly and or a PL-N latch attached and secured with toggle pin
lifting procedures are not used. may be used for lifting personnel. A hook with a Crosby
■ A falling load may cause serious injury or death. SS-4055 latch attached shall NOT be used for
■ Install hoist ring bolt to torque requirements personnel lifting.
(www.thecrosbygroup.com) for the HR-125, HR-1000, ■ See OSHA Directive CPL 2-1.29 - Crosby does not
HR125C, HR-1000CT, HR-125M, HR-1000M and HR125W, recommend the placement of lanyards directly into the
SS-125 and SS-125M respectively. positive locking Crosby hook when hoisting personnel.
■ Web sling HR-125W spool bolt must be securely tightened Crosby requires that all suspension systems (vertical
in place. The jam nut must then be securely tightened onto lifelines / lanyard) shall be gathered at the positive
the connecting bolt. locked load hook by use of a master link, or a bolt-type
■ Read, understand and follow all instructions and shackle secured with cotter pin.
chart information. ■ Threads may corrode and/or strip and drop the load.
■ Do not use with damaged slings, chain or webbing. ■ Remove securement nut to inspect or to replace S-322,
For inspection criteria see ASME B30.9. S-3316, and S-3319 bearing washers (2).
■ Use only genuine Crosby parts as replacements. ■ Hook must always support the load. The load must never
■ HR-125C chain connecting pin must be properly secured be supported by the latch.
with the locking pin into the clevis ear. ■ Never apply more force than the hook’s assigned
■ Before use tighten Working Load Limit (WLL) rating.
■ Read and understand these instructions before using hook.

information, see The Crosby Group
at www.thecrosbygroup.com
Malleable Clips— Skookum

Zinc Plated Master Link
Warnings
WARNING
■ Failure to read, understand and follow these instructions
may cause injury and property damage.
WARNING
■ Follow all Warnings, Use and Application Instructions as
supplied by the Manufacturer. Improper use of links can result in serious bodily injury, property
■ Read and understand these instructions before using damage and/or death. Only properly trained and competent
malleable clips. persons are allowed to use links in a proper application. Never
■ Never use malleable clips for critical, heavy duty or exceed working load limit.
overhead loads, such as lifting slings, support lines,
guy lines, towing lines, tie downs, scaffolds, etc. For complete warning and application
■ Malleable clips are to be used for making eye termination information, see The Ulven Companies at
assemblies.
www.ulvencompanies.com
- Only with right regular lay wire rope
- Only for non-critical light duty uses with small applied
loads, such as hand rails, fencing, guard rails, etc.
■ Apply first load to test the assembly. This load should be of
equal or greater weight than loads expected in use. Next, check
and retighten nuts to recommended torque.
456

SHUR-LOC® Swivel Hooks Golden Gate® Hooks
Warnings Warnings
WARNING WARNING
■ Loads may disengage from hook if proper procedures ■ Loads may disengage from hook if proper procedures are
are not followed. not followed.
■ A falling load may cause serious injury or death. ■ A falling load may cause serious injury or death.
■ Positive locking latch will unlock when trigger is depressed. ■ Before using, inspect the hook and gate daily to ensure it is
Never use hook unless hook and latch are fully closed in proper operating condition.
and locked. ■ Failure to properly insert the pin could result in the
■ Keep body parts clear of pinch point between hook tip and load falling.
hook latch when closing. ■ All Golden Gate® Hooks with threaded shanks require a pin
■ Keep hand(s) from between throat of hook and sling or to secure the nut to the shank. This pin prevents the nut
other device. from backing off or unscrewing from the threads and
■ Do not use hook tip for lifting. causing the load to drop.
■ Shank threads may corrode and/or strip and drop the load. ■ If the pin and nut are removed from the shank to replace
■ Remove securement nut to inspect threads for corrosion any hook components, the pin and nut must be installed
or to replace S-1326A bearing washers (2) and or S-13326 before use.
thrust bearing. 1. NOTE: If a solid pin was used, the old pin “must”be
■ Never apply more force than the hook’s assigned discarded and a new pin inserted to secure the nut to
Working Load Limit (WLL) rating. the shank.
■ See OSHA Rule 1926.1431(g) and 1926.1501(g) for 2. If a spring pin (coil type) was used, it may be reused
personnel hoisting by cranes or derricks. A Crosby 318A, provided that the spring pin and / or the drill hole
1326A, 13326, 1316A, or 1317A hook may be used for was not damaged.
lifting personnel. ■ The gate is not a load-bearing device. Do not allow the sling
■ Use only genuine Crosby parts as replacements. or other loads to bear against the gate.
■ Read and understand these instructions before using hook. ■ Threads may corrode and / or strip and drop the load.
■ Hands, fingers and body should be kept away from the
hook and load whenever possible.
For complete warning and application ■ Never apply more force than the hook’s assigned
information, see The Crosby Group Working Load Limit (WLL) rating.
at www.thecrosbygroup.com ■ Read and understand these instructions before using.

Hook Latch Kit WARNING

Warnings ■

Loads may disengage from hook if proper procedures are
not followed.
■ A falling load may cause serious injury or death.
■ See OSHA Rule 1926.1431(g)(4)(iv)(B) and
1926.1501(g)(1)(i) (A) for personnel hoisting for cranes
and derricks. Only a Crosby or McKissick hook with
a PL Latch attached and secured with bolt, nut and cotter
(or Crosby Toggle Pin) or a Crosby hook with a S-4320 Latch
attached and secured with a cotter pin, or a Crosby
SHUR-LOC® hook in the locked position may be used for
any personnel hoisting. A hook with a Crosby SS-4055 latch
attached shall NOT be used for personnel lifting.
■ Hook must always support the load. The load must never
For complete warning and application be supported by the latch.
information, see The Crosby Group ■ Read and understand these instructions before using
at www.thecrosbygroup.com hook and latch.
457

Weld-On Pivot Link Pear-Shaped Master
Warnings Links Warnings
WARNING
CHAIN SLING FAILURE CAN CAUSE
DEATH OR INJURY.
SLING FAILURE RESULTS FROM MISUSE,
DAMAGE, ANDEXCESSIVE WEAR
WARNING
■ Loads may disengage from link if proper welding, assembly,
and lifting procedures are not used. WARNING
■ A falling load may cause serious injury or death. ■ NEVER use a sling without training.
■ Do not use with damaged slings or chain. For sling ■ ALWAYS inform yourself…Ask your employer for the
inspection criteria see ASME B30.9. manufacturer’s sling use limitations.
■ Read and understand these instructions before welding on, ■ ALWAYS comply with applicable Federal and local
or using the pivoting link. regulations.
■ ALWAYS know load weight.
■ NEVER use a sling without a legible rated load tag.
For complete warning and application ■ NEVER overload a sling.
information, see The Crosby Group ■ NEVER ride on sling or load.
■ NEVER use an improper sling configuration.
■ NEVER use a worn-out or damaged sling.
■ NEVER use a sling in extreme temperatures.
■ NEVER use a sling in acidic conditions.
Weld-On Excavator For complete warning and application

Hooks Warnings information, see Gunnebo Johnson
at www.gunnebojohnson.com
WARNING
ALLOY STEEL SELF-LOCKING HOOKS Eye Type Self-Locking
■ LOAD DISENGAGEMENT CAN CAUSE & Swivel Bronze
DEATH OR INJURY
DISENGAGEMENT RESULTS FROM

Bushing Hooks
MISUSE, DAMAGE AND EXCESSIVE WEAR Warnings
WARNING WARNING
■ NEVER use a hook without training.
ALLOY STEEL SELF-LOCKING HOOKS
■ ALWAYS inform yourself…Ask your employer for
■ LOAD DISENGAGEMENT CAN CAUSE
hook safe use instructions.
DEATH OR INJURY
■ ALWAYS comply with applicable Federal and
DISENGAGEMENT RESULTS FROM
local regulations.
MISUSE, DAMAGE AND EXCESSIVE WEAR
■ ALWAYS know hook load.
■ NEVER use a hook without a legible product identifier.
■ NEVER overload a hook. WARNING
■ NEVER rise a hook or load. ■ NEVER use a hook without training.
■ NEVER rig a hook to load improperly ■ ALWAYS inform yourself…Ask your employer for
■ NEVER use a worm-out or damaged hook. hook safe use instructions.
■ NEVER use a hook in extreme temperatures. ■ ALWAYS comply with applicable Federal and
■ NEVER use a hook in acidic conditions. local regulations.
■ ALWAYS know hook load.
■ NEVER use a hook without a legible product identifier.
For complete warning and application ■ NEVER overload a hook.
information, see Gunnebo Johnson ■ NEVER rise a hook or load.
■ NEVER rig a hook to load improperly
at www.gunnebojohnson.com ■ NEVER use a worm-out or damaged hook.
■ NEVER use a hook in extreme temperatures.
■ NEVER use a hook in acidic conditions.

information, see Gunnebo Johnson
at www.gunnebojohnson.com
458

S-4320 Latch Kits PL-N/O Latch Kits
Warnings Warnings
WARNING WARNING
■ Loads may disengage from hook if proper procedures ■ Loads may disengage from hook if proper procedures
are not followed. are not followed.
■ A falling load may cause serious injury or death. ■ A falling load may cause serious injury or death.
■ Hook must always support the load. The load must never ■ See OSHA Rule 1926.1431(g) and 1926.1501(g) for
be supported by the latch. Personnel Hoisting by Crane or Derricks. A Crosby or
■ See OSHA Rule 1926.1431(g) and 1926.1501(g) for McKissick Hook with a Positive Locked PL-N/O or S-4320
personnel hoisting by crane or Derricks. A Crosby S-319N, Latch may be used to Lift Personnel.
S-320N, S-322N, S-1320, A-339 and A-1339 Hook with an ■ Hook must always support the load. The load must never
S-4320 latch attached (When secured with cotter pin) may be supported by the latch.
be used for lifting personnel. ■ Read and understand these instructions before using
■ An S-4320 Latch is only to be used with a Crosby S-319N, hook and latch.
S-320N, S-322N, S-1320, A-339 and A-1339 Hook.
■ DO NOT use this latch in applications requiring
non-sparking.
S-4055 Latch Kits

PL Latch Kits Warnings
Warnings
WARNING
WARNING ■ Loads may disengage from hook if proper procedures
■ Loads may disengage from hook if proper procedures are are not followed.
not followed. ■ A falling load may cause serious injury or death.
■ A falling load may cause serious injury or death. ■ See OSHA Rule 1926.1431(g)(1)(i)(A) and
■ See OSHA Rule 1926.1431(g) and 1926.1501(g) for 1926.1501(g)(4)(iv)(B). A hook and this style latch must
Personnel Hoisting by Cranes or Derricks. A Crosby or not be used for lifting personnel.
McKissick Hook with a positive Locked PL or S-4320 Latch ■ Hook must always support the load. The load must
may be used to Lift Personnel. never be supported by the latch.
■ Hook must always support the load. The load must never ■ Read and understand these instructions before using
be supported by the latch. hook and latch.
■ Read and understand these instructions before using
hook and latch. For complete warning and application
For complete warning and application at www.thecrosbygroup.com
459

S-4088 Alloy Hook Chicago Hardware
Latch Kits Warnings Forged & Stainless Steel
Eye Bolts Warnings
WARNING
■ Loads may disengage from hook if proper procedures
are not followed. For complete warning and application
■ A falling load may cause serious injury or death. information, see Chicago Hardware & Fixture
■ Hook must always support the load. The load must never Company at www.chicagohardware.com
be supported by the latch.
■ See OSHA Rule 1926.1431(g) and 1926.1501(g) for
personnel hoisting by crane or Derricks. A Crosby S-319N,
Crosby Forged Eye Bolts

S-320N, S-322N, S-1320, A-339 and A-1339 Hook with an
S-4320 latch attached (When secured with cotter pin) may

■
be used for lifting personnel.
An S-4320 Latch is only to be used with a Crosby S-319N, Warnings
S-320N, S-322N, S-1320, A-339 and A-1339 Hook.
■ DO NOT use this latch in applications requiring
non-sparking.

Regular Shoulder
Nut Eye Nut Eye
G-Link™ WARNING
Synthetic Sling ■ Load may slip or fall if proper eye bolt assembly and lifting
Connector
■
procedures are not used.
A falling load can seriously injure or kill.
Warnings ■

Read and understand both sides of these instructions, and
follow all eye bolt safety information presented here.
■ Read, understand, and follow information in diagrams and
charts below before using eye bolt assemblies.

WARNING at www.thecrosbygroup.com
■ Can fail if damaged, misused or overloaded.
■ Inspect before use.
RUD Eye Bolt

■ Use only if trained.
■ Observe rated capacity.
■

DEATH or INJURY can occur from improper use
or maintenance. Warnings
information, see Slingmax Rigging Solutions
at www.slingmax.com
information, see The RUD Group at
www.rud.com
460

Chain Laclede Chain
Warnings Warnings
WARNING
■ This chain is not to be used for overhead lifting.
■ Working Load Limit is not to be exceeded.
Cold Shut WARNING

Warnings ■
■
This chain is not to be used for overhead lifting.
Never exceed the Working Load Limit.

information, see Laclede Chain Manufacturing
Company, LLC. at www.lacledechain.com
WARNING
■ Not to be used for load securement (tie-down).

information, see Columbus McKinnon
Corporation at www.cmworks.com
Link
Warnings
Clevis Quick Repair

Link Link Link
WARNING
■ Not to be used for load securement (tie-down).

information, see Columbus McKinnon
Corporation at www.cmworks.com
461

MazzellaCatalog13 RiggingHardware LR

Uploaded by

Copyright:

Available Formats

MazzellaCatalog13 RiggingHardware LR

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MazzellaCatalog13 RiggingHardware LR

Uploaded by

Copyright:

Available Formats

Hardware

MazzellaCatalog13_Hardware.indd 354 7/3/13 9:40 AM

■ Hoist rings—standard and metric

All hardware products meet the ASME B30.26 specification.

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 355 7/3/13 9:40 AM

MazzellaCatalog13_Hardware.indd 356 7/3/13 9:40 AM

3. A “Consequence Statement,” such as “FAILURE

words, such as “IMPORTANT” or “NOTICE.”

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 357 7/3/13 9:40 AM

■ Capacities 1/3 thru 55 metric tons, grade 6.

MazzellaCatalog13_Hardware.indd 358 7/3/13 9:40 AM

■ Capacities 1/3 thru 55 metric tons, grade 6.

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 359 7/3/13 9:40 AM

■ Capacities 1/2 through 35 metric tons.

MazzellaCatalog13_Hardware.indd 360 7/3/13 9:40 AM

■ Capacities 1/2 through 35 metric tons.

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 361 7/3/13 9:40 AM

■ Capacities 2 thru 21 metric tons. Meets performance

MazzellaCatalog13_Hardware.indd 362 7/3/13 9:40 AM

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 363 7/3/13 9:40 AM

■ Capacities 1/3 thru 150 metric tons, grade 6.

MazzellaCatalog13_Hardware.indd 364 7/3/13 9:40 AM

■ Capacities 1/3 thru 150 metric tons, grade 6.

† Individually Proof Tested with certification.

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 365 7/3/13 9:40 AM

■ Quenched and Tempered.

MazzellaCatalog13_Hardware.indd 366 7/3/13 9:40 AM

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 367 7/3/13 9:40 AM

MazzellaCatalog13_Hardware.indd 368 7/3/13 9:40 AM

* WARNING: Working load limit is not to be exceeded. Round Pin

1-5/8 35 – – M885A 1.750 1.906 2.625 4.125 6.250 4.000 23.50

2-1/2 85 – – MC860AG 2.750 2.906 4.125 6.250 10.500 6.750 90.50

3 120 – – MC862AG 3.250 3.406 5.000 6.750 13.000 7.375 137.00

* WARNING: Working load limit is not to be exceeded.

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 369 7/3/13 9:40 AM

* WARNING: Working load limit is not to be exceeded. Round Pin

Bolt & Nut

Working Product Code Dimensions (in.)

* WARNING: Working load limit is not to be exceeded.

MazzellaCatalog13_Hardware.indd 370 7/3/13 9:40 AM

All dimensions in inches.

No. 159A Sheet Pile

www.jhenryholland.com www.alabamaslingcenter.com Phone: 423-634-9005 (Chattanooga) www.kcicraneservice.com

MazzellaCatalog13_Hardware.indd 371 7/3/13 9:40 AM

Alloy Towing Shackles Replacement Bolts

Galvanized Bolt Type

Size Working Bolt Length Width Between Eyes D Approx.

U.S. Registered Trademark No. 2,011,393

MazzellaCatalog13_Hardware.indd 372 7/3/13 9:40 AM

Grade: 316NM Stainless Steel

E. ____________________________________________ Chain Anchor

Contact us with your dimensions, using the

■ UD Universal bolts and nuts for VLBG - 100% crack detected.

■ istribution of the load force due to the 2 point fixing, hence an

■ The weldable load ring with limit stops is available for