Oscilloscope PDF

Agilent InfiniiVision
2000 X-Series
Oscilloscopes
User's Guide
Notices
© Agilent Technologies, Inc. 2005-2011 Warranty defined in FAR 52.227-19(c)(1-2) (June
1987). U.S. Government users will receive
No part of this manual may be reproduced in The material contained in this docu-
any form or by any means (including elec- no greater than Limited Rights as defined in
ment is provided “as is,” and is sub- FAR 52.227-14 (June 1987) or DFAR
tronic storage and retrieval or translation ject to being changed, without notice, 252.227-7015 (b)(2) (November 1995), as
into a foreign language) without prior agree- in future editions. Further, to the max-
ment and written consent from Agilent applicable in any technical data.
imum extent permitted by applicable
Technologies, Inc. as governed by United law, Agilent disclaims all warranties,
States and international copyright laws. Safety Notices
either express or implied, with regard
to this manual and any information
Manual Part Number contained herein, including but not
limited to the implied warranties of CAUTION
75015-97012
merchantability and fitness for a par-
ticular purpose. Agilent shall not be A CAUTION notice denotes a haz-
Edition
liable for errors or for incidental or ard. It calls attention to an operat-
Third edition, June 2011 consequential damages in connec- ing procedure, practice, or the like
Printed in Malaysia tion with the furnishing, use, or per-
formance of this document or of any that, if not correctly performed or
Agilent Technologies, Inc. information contained herein. Should adhered to, could result in damage
1900 Garden of the Gods Road Agilent and the user have a separate to the product or loss of important
Colorado Springs, CO 80907 USA written agreement with warranty data. Do not proceed beyond a
terms covering the material in this
document that conflict with these CAUTION notice until the indicated
Print History terms, the warranty terms in the sep- conditions are fully understood and
arate agreement shall control. met.
75015-97000, January 2011
75015-97011, February 2011 Technology Licenses
75015-97012, June 2011 The hardware and/or software described in
this document are furnished under a license WA R N IN G
Trademarks and may be used or copied only in accor-
Java is a U.S. trademark of Sun Microsys- dance with the terms of such license. A WARNING notice denotes a
tems, Inc. hazard. It calls attention to an
Restricted Rights Legend operating procedure, practice, or
Sun, Sun Microsystems, and the Sun Logo
are trademarks or registered trademarks of If software is for use in the performance of a the like that, if not correctly per-
Sun Microsystems, Inc. in the U.S. and other U.S. Government prime contract or subcon- formed or adhered to, could result
countries. tract, Software is delivered and licensed as
“Commercial computer software” as
in personal injury or death. Do not
defined in DFAR 252.227-7014 (June 1995), proceed beyond a WARNING
or as a “commercial item” as defined in FAR notice until the indicated condi-
2.101(a) or as “Restricted computer soft- tions are fully understood and
ware” as defined in FAR 52.227-19 (June
1987) or any equivalent agency regulation or met.
contract clause. Use, duplication or disclo-
sure of Software is subject to Agilent Tech-
nologies’ standard commercial license
terms, and non-DOD Departments and
Agencies of the U.S. Government will
receive no greater than Restricted Rights as
2 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

InfiniiVision 2000 X-Series Oscilloscopes—At a Glance
Table 1 2000 X-Series Model Numbers, Bandwidths
Bandwidth 70 MHz 100 MHz 200 MHz

2-Channel + 8 Logic MSO-X 2002A MSO-X 2012A MSO-X 2022A
Channels MSO
4-Channel + 8 Logic MSO-X 2004A MSO-X 2014A MSO-X 2024A

Channels MSO
2-Channel DSO DSO-X 2002A DSO-X 2012A DSO-X 2022A
4-Channel DSO DSO-X 2004A DSO-X 2014A DSO-X 2024A
The Agilent InfiniiVision 2000 X- Series oscilloscopes deliver these features:

• 70 MHz, 100 MHz, and 200 MHz bandwidth models.
• 2- and 4- channel digital storage oscilloscope (DSO) models.
• 2+8- channel and 4+8- channel mixed- signal oscilloscope (MSO) models.
Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 3

An MSO lets you debug your mixed- signal designs using analog signals
and tightly correlated digital signals simultaneously. The 8 digital
channels have a 1 GSa/s sample rate, with a 50 MHz toggle rate.
• 8.5 inch WVGA display.
• Interleaved 2 GSa/s or non- interleaved 1 GSa/s sample rate.
• Interleaved 100 Kpts or non- interleaved 50 Kpts MegaZoom IV memory
for the fastest waveform update rates, uncompromised.
• All knobs are pushable for making quick selections.
• Trigger types: edge, pulse width, pattern, and video.
• Math wavefroms: add, subtract, multiply, and FFT.
• Reference waveforms (2) for comparing with other channel or math
waveforms.
• Many built- in measurements.
• Built- in license- enabled waveform generator with: sine, square, ramp,
pulse, DC, noise.
• USB ports make printing, saving and sharing data easy.
• Optional LAN/VGA module for connecting to a network and displaying
the screen on a different monitor.
• Optional GPIB module.
• A Quick Help system is built into the oscilloscope. Press and hold any
key to display Quick Help. Complete instructions for using the quick
help system are given in “Access the Built- In Quick Help" on page 40.
For more information about InfiniiVision oscilloscopes, see:
"www.agilent.com/find/scope"

In This Guide
This guide shows how to use the InfiniiVision 2000 X- Series oscilloscopes.
When unpacking and using the • Chapter 1, “Getting Started,” starting on page 19
oscilloscope for the first time, see:
When displaying waveforms and • Chapter 2, “Horizontal Controls,” starting on page 43
acquired data, see: • Chapter 3, “Vertical Controls,” starting on page 55
• Chapter 4, “Math Waveforms,” starting on page 63
• Chapter 5, “Reference Waveforms,” starting on page
75
• Chapter 6, “Digital Channels,” starting on page 79
• Chapter 7, “Display Settings,” starting on page 99
• Chapter 8, “Labels,” starting on page 105
When setting up triggers or changing • Chapter 9, “Triggers,” starting on page 111
how data is acquired, see: • Chapter 10, “Trigger Mode/Coupling,” starting on
page 133
• Chapter 11, “Acquisition Control,” starting on page 141
Making measurements and analyzing • Chapter 12, “Cursors,” starting on page 157
data: • Chapter 13, “Measurements,” starting on page 167
• Chapter 14, “Mask Testing,” starting on page 187
When using the built-in waveform • Chapter 15, “Waveform Generator,” starting on page
generator, see: 199
When saving, recalling, or printing, • Chapter 16, “Save/Recall (Setups, Screens, Data),”
see: starting on page 205
• Chapter 17, “Print (Screens),” starting on page 219
When using the oscilloscope's utility • Chapter 18, “Utility Settings,” starting on page 223
functions or web interface, see: • Chapter 19, “Web Interface,” starting on page 241
For reference information, see: • Chapter 20, “Reference,” starting on page 255

Abbreviated instructions for pressing a series of keys and softkeys
TIP
Instructions for pressing a series of keys are written in an abbreviated manner. Instructions
for pressing [Key1], then pressing Softkey2, then pressing Softkey3 are abbreviated as
follows:
Press [Key1]> Softkey2 > Softkey3.
The keys may be a front panel [Key] or a Softkey. Softkeys are the six keys located directly
below the oscilloscope display.

Contents
InfiniiVision 2000 X-Series Oscilloscopes—At a Glance 3
In This Guide 5
1 Getting Started
Inspect the Package Contents 19
Install the Optional LAN/VGA or GPIB Module 22
Tilt the Oscilloscope for Easy Viewing 22
Power-On the Oscilloscope 23
Connect Probes to the Oscilloscope 24
Maximum input voltage at analog inputs 24
Do not float the oscilloscope chassis 24

Input a Waveform 25
Recall the Default Oscilloscope Setup 25
Use Auto Scale 26
Compensate Passive Probes 27
Learn the Front Panel Controls and Connectors 28
Front Panel Overlays for Different Languages 35
Learn the Rear Panel Connectors 37
Learn the Oscilloscope Display 38
Access the Built-In Quick Help 40

2 Horizontal Controls
To adjust the horizontal (time/div) scale 44
To adjust the horizontal delay (position) 45
Panning and Zooming Single or Stopped Acquisitions 46
To change the horizontal time mode (Normal, XY, or Roll) 47
XY Time Mode 48
To display the zoomed time base 50
To change the horizontal scale knob's coarse/fine adjustment
setting 52
To position the time reference (left, center, right) 52
Navigating the Time Base 53
To navigate time 53
To navigate segments 53
3 Vertical Controls
To turn waveforms on or off (channel or math) 56
To adjust the vertical scale 57
To adjust the vertical position 57
To specify channel coupling 57
To specify bandwidth limiting 58
To change the vertical scale knob's coarse/fine adjustment
setting 58
To invert a waveform 59
Setting Analog Channel Probe Options 59
To specify the channel units 60
To specify the probe attenuation 60
To specify the probe skew 61

4 Math Waveforms
To display math waveforms 63
To perform a transform function on an arithmetic operation 64
To adjust the math waveform scale and offset 65
Multiply 65
Add or Subtract 66
FFT Measurement 67
FFT Measurement Hints 71
FFT Units 72
FFT DC Value 72
FFT Aliasing 72
FFT Spectral Leakage 74
Units for Math Waveforms 74
5 Reference Waveforms
To save a waveform to a reference waveform location 75
To display a reference waveform 76
To scale and position reference waveforms 77
To adjust reference waveform skew 77
To display reference waveform information 78
To save/recall reference waveform files to/from a USB storage
device 78
6 Digital Channels
To connect the digital probes to the device under test 79
Probe cable for digital channels 80

Acquiring waveforms using the digital channels 83

To display digital channels using AutoScale 83
Interpreting the digital waveform display 84
To change the displayed size of the digital channels 85
To switch a single channel on or off 86
To switch all digital channels on or off 86
To switch groups of channels on or off 86
To change the logic threshold for digital channels 86
To reposition a digital channel 87
To display digital channels as a bus 88
Digital channel signal fidelity: Probe impedance and
grounding 91
Input Impedance 92
Probe Grounding 94
Best Probing Practices 96
To replace digital probe leads 96
7 Display Settings
To adjust waveform intensity 99
To set or clear persistence 101
To clear the display 102
To select the grid type 102
To adjust the grid intensity 103
To freeze the display 103
8 Labels
To turn the label display on or off 105
To assign a predefined label to a channel 106

To define a new label 107
To load a list of labels from a text file you create 108
To reset the label library to the factory default 109
9 Triggers
Adjusting the Trigger Level 112
Forcing a Trigger 113
Edge Trigger 113
Pattern Trigger 116
Hex Bus Pattern Trigger 118
Pulse Width Trigger 119
Video Trigger 121
To trigger on a specific line of video 125
To trigger on all sync pulses 126
To trigger on a specific field of the video signal 127
To trigger on all fields of the video signal 128
To trigger on odd or even fields 129
10 Trigger Mode/Coupling
To select the Auto or Normal trigger mode 134
To select the trigger coupling 136
To enable or disable trigger noise rejection 137
To enable or disable trigger HF Reject 137
To set the trigger holdoff 138
External Trigger Input 138
Maximum voltage at oscilloscope external trigger input 139

11 Acquisition Control
Running, Stopping, and Making Single Acquisitions (Run
Control) 141
Overview of Sampling 143
Sampling Theory 143
Aliasing 143
Oscilloscope Bandwidth and Sample Rate 144
Oscilloscope Rise Time 145
Oscilloscope Bandwidth Required 146
Memory Depth and Sample Rate 147
Selecting the Acquisition Mode 147
Normal Acquisition Mode 148
Peak Detect Acquisition Mode 148
Averaging Acquisition Mode 151
High Resolution Acquisition Mode 153
Acquiring to Segmented Memory 153
Navigating Segments 155
Infinite Persistence with Segmented Memory 155
Segmented Memory Re-Arm Time 156
Saving Data from Segmented Memory 156
12 Cursors
To make cursor measurements 158
Cursor Examples 161
13 Measurements
To make automatic measurements 168
Measurements Summary 169
Snapshot All 171
Voltage Measurements 171

Peak-Peak 172
Maximum 172
Minimum 172
Amplitude 172
Top 173
Base 174
Overshoot 174
Preshoot 175
Average 176
DC RMS 176
AC RMS 177
Time Measurements 179
Period 179
Frequency 180
+ Width 181
– Width 181
Burst Width 181
Duty Cycle 181
Rise Time 182
Fall Time 182
Delay 182
Phase 183
Measurement Thresholds 184
Measurement Window with Zoom Display 186
14 Mask Testing
To create a mask from a "golden" waveform (Automask) 187
Mask Test Setup Options 189
Mask Statistics 192
To manually modify a mask file 193

Building a Mask File 196
How is mask testing done? 198
15 Waveform Generator
To select generated waveform types and settings 199
To output the waveform generator sync pulse 202
To specify the waveform generator output load 203
To use waveform generator logic presets 203
To restore waveform generator defaults 204
16 Save/Recall (Setups, Screens, Data)

Saving Setups, Screen Images, or Data 205
To save setup files 207
To save BMP or PNG image files 207
To save CSV, ASCII XY, or BIN data files 208
To save ALB data files 209
Length Control 211
To save reference waveform files to a USB storage device 213
To save masks 213
To navigate storage locations 214
To enter file names 214
Recalling Setups, Masks, or Reference Waveforms 215
To recall setup files 215
To recall mask files 216
To recall reference waveform files from a USB storage
device 216
Recalling Default Setups 216
Performing a Secure Erase 217

17 Print (Screens)
To print the oscilloscope's display 219
To set up network printer connections 220
To specify the print options 221
To specify the palette option 222
18 Utility Settings
I/O Interface Settings 223
Setting up the Oscilloscope's LAN Connection 224
To establish a LAN connection 225
Stand-alone (Point-to-Point) Connection to a PC 226
File Explorer 227
Setting Oscilloscope Preferences 229
To choose "expand about" center or ground 229
To disable/enable transparent backgrounds 230
To load the default label library 230
To set up the screen saver 230
To set AutoScale preferences 231
Setting the Oscilloscope's Clock 232
Setting the Rear Panel TRIG OUT Source 232
Performing Service Tasks 233
To perform user calibration 234
To perform hardware self test 236
To perform front panel self test 236
To display oscilloscope information 236
To display the user calibration status 237
To clean the oscilloscope 237
To check warranty and extended services status 237
To contact Agilent 237

To return the instrument 237
Configuring the [Quick Action] Key 238
19 Web Interface
Accessing the Web Interface 242
Browser Web Control 243
Real Scope Remote Front Panel 244
Simple Remote Front Panel 245
Remote Programming via the Web Interface 246
Remote Programming with Agilent IO Libraries 247
Save/Recall 247
Saving Files via the Web Interface 247
Recalling Files via the Web Interface 249
Get Image 249
Identification Function 250
Instrument Utilities 251
Setting a Password 252
20 Reference
Specifications and Characteristics 255
Measurement Category 255
Oscilloscope Measurement Category 256
Measurement Category Definitions 256
Transient Withstand Capability 257
Maximum input voltage at analog inputs 257
Maximum input voltage at digital channels 257

Environmental Conditions 257

Probes and Accessories 258
Passive Probes 258
Differential Probes 259
Current Probes 259
Accessories Available 260
Loading Licenses and Displaying License Information 261
Licensed Options Available 261
Other Options Available 262
Upgrading to an MSO 262
Software and Firmware Updates 262
Binary Data (.bin) Format 262
Binary Data in MATLAB 263
Binary Header Format 264
Example Program for Reading Binary Data 266
Examples of Binary Files 266
CSV and ASCII XY files 269
CSV and ASCII XY file structure 270
Minimum and Maximum Values in CSV Files 270
Acknowledgements 271
Index

Agilent InfiniiVision 2000 X-Series Oscilloscopes
User's Guide
1
Getting Started
Inspect the Package Contents 19
Tilt the Oscilloscope for Easy Viewing 22
Power-On the Oscilloscope 23
Connect Probes to the Oscilloscope 24
Input a Waveform 25
Recall the Default Oscilloscope Setup 25
Use Auto Scale 26
Compensate Passive Probes 27
Learn the Front Panel Controls and Connectors 28
Learn the Rear Panel Connectors 37
Learn the Oscilloscope Display 38
Access the Built-In Quick Help 40
This chapter describes the steps you take when using the oscilloscope for
the first time.
Inspect the Package Contents

• Inspect the shipping container for damage.
If your shipping container appears to be damaged, keep the shipping
container or cushioning material until you have inspected the contents
of the shipment for completeness and have checked the oscilloscope
mechanically and electrically.
• Verify that you received the following items and any optional
accessories you may have ordered:
19
1 Getting Started
• InfiniiVision 2000 X- Series oscilloscope.

• Power cord (country of origin determines specific type).
• Oscilloscope probes:
• Two probes for 2- channel models.
• Four probes for 4- channel models.
• Documentation CD- ROM.

Getting Started 1
InfiniiVision 2000 X-Series oscilloscope
N2862B probes
(Qty 2 or 4)
Documentation CD
Digital Probe Kit*

(MSO models only)
Power cord
(Based on country
of origin)
*N6459-60001 Digital Probe Kit contains:

N6459-61601 8-channel cable (qyt 1)
01650-82103 2-inch probe ground leads (qyt 3)
5090-4832 Grabber (qty 10)
Digital probe replacement parts are listed in the

"Digital Channels" chapter.
See Also • “Accessories Available" on page 260

1 Getting Started
Install the Optional LAN/VGA or GPIB Module

If you need to install a DSOXLAN LAN/VGA module or a DSOXGPIB GPIB
module, perform this installation before you power on the oscilloscope.
1 If you need to remove a module before installing a different module,
pinch the module's spring tabs, and gently remove the module from the
slot.
2 To install a module, slide the module into the slot on the back until it
is fully seated.
The module's spring tabs will latch into the slot, keeping the module in
place.
LAN/VGA Module
Module Slot
GPIB Module
L6GC>C</B6>CI6>C
<GDJC9ID 6KD>9
:A:8IG>8H=D8@
s &%%"&'%K!*%$+%$)%%=o
s &%%"')%K!*%$+%=o
&%% LViihB6M
The LAN/VGA or GPIB module must be installed before powering on the oscilloscope.
NOTE
Tilt the Oscilloscope for Easy Viewing

There are tabs under the oscilloscope's front feet that can be flipped out
to tilt the oscilloscope.

Getting Started 1
Flip-Out Tabs
Power-On the Oscilloscope

Power Line voltage, frequency, and power:
Requirements • ~Line 100- 120 Vac, 50/60/400 Hz
• 100- 240 Vac, 50/60 Hz
• 100 W max
Ventilation The air intake and exhaust areas must be free from obstructions.
Requirements Unrestricted air flow is required for proper cooling. Always ensure that
the air intake and exhaust areas are free from obstructions.
The fan draws air in from the left side and bottom of the oscilloscope and
pushes it out behind the oscilloscope.
When using the oscilloscope in a bench- top setting, provide at least 2"
clearance at the sides and 4" (100 mm) clearance above and behind the
oscilloscope for proper cooling.
To power-on the 1 Connect the power cord to the rear of the oscilloscope, then to a
oscilloscope suitable AC voltage source. Route the power cord so the oscilloscope's
feet and legs do not pinch the cord.

1 Getting Started
2 The oscilloscope automatically adjusts for input line voltages in the

range 100 to 240 VAC. The line cord provided is matched to the country
of origin.
Always use a grounded power cord. Do not defeat the power cord ground.
WARNIN G
3 Press the power switch.

The power switch is located on the lower left corner of the front panel.
The oscilloscope will perform a self- test and will be operational in a few
seconds.
Connect Probes to the Oscilloscope

1 Connect the oscilloscope probe to an oscilloscope channel BNC
connector.
2 Connect the probe's retractable hook tip to the point of interest on the
circuit or device under test. Be sure to connect the probe ground lead
to a ground point on the circuit.
Maximum input voltage at analog inputs

CAUTION
CAT I 300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk
With 10073C 10:1 probe: CAT I 500 Vpk, CAT II 400 Vpk
With N2862A or N2863A 10:1 probe: 300 Vrms
Do not float the oscilloscope chassis

CAUTION
Defeating the ground connection and "floating" the oscilloscope chassis will probably
result in inaccurate measurements and may also cause equipment damage. The probe
ground lead is connected to the oscilloscope chassis and the ground wire in the power
cord. If you need to measure between two live points, use a differential probe with
sufficient dynamic range.

Getting Started 1
Do not negate the protective action of the ground connection to the oscilloscope. The
WARNIN G
oscilloscope must remain grounded through its power cord. Defeating the ground
creates an electric shock hazard.
Input a Waveform
The first signal to input to the oscilloscope is the Demo 2, Probe Comp
signal. This signal is used for compensating probes.
1 Connect an oscilloscope probe from channel 1 to the Demo 2 (Probe
Comp) terminal on the front panel.
2 Connect the probe's ground lead to the ground terminal (next to the
Demo 2 terminal).
Recall the Default Oscilloscope Setup

To recall the default oscilloscope setup:
1 Press [Default Setup].
The default setup restores the oscilloscope's default settings. This places
the oscilloscope in a known operating condition. The major default settings
are:
Table 2 Default Configuration Settings
Horizontal Normal mode, 100 µs/div scale, 0 s delay, center time reference.
Vertical (Analog) Channel 1 on, 5 V/div scale, DC coupling, 0 V position.

Trigger Edge trigger, Auto trigger mode, 0 V level, channel 1 source, DC coupling,
rising edge slope, 40 ns holdoff time.
Display Persistence off, 20% grid intensity.
Other Acquire mode normal, [Run/Stop] to Run, cursors and measurements off.
Labels All custom labels that you have created in the Label Library are preserved (not
erased), but all channel labels will be set to their original names.

1 Getting Started
In the Save/Recall Menu, there are also options for restoring the complete
factory settings (see “Recalling Default Setups" on page 216) or performing
a secure erase (see “Performing a Secure Erase" on page 217).
Use Auto Scale

Use [Auto Scale] to automatically configure the oscilloscope to best display
the input signals.
1 Press [Auto Scale].
You should see a waveform on the oscilloscope's display similar to this:
2 If you want to return to the oscilloscope settings that existed before,

press Undo AutoScale.
3 If you want to enable "fast debug" autoscaling, change the channels
autoscaled, or preserve the acquisition mode during autoscale, press
Fast Debug, Channels, or Acq Mode.
These are the same softkeys that appear in the AutoScale Preferences
Menu. See “To set AutoScale preferences" on page 231.

Getting Started 1
If you see the waveform, but the square wave is not shaped correctly as
shown above, perform the procedure “Compensate Passive Probes" on
page 27.
If you do not see the waveform, make sure the probe is connected
securely to the front panel channel input BNC and to the left side,
Demo 2, Probe Comp terminal.
How AutoScale Auto Scale analyzes any waveforms present at each channel and at the
Works external trigger input. This includes the digital channels, if connected.
Auto Scale finds, turns on, and scales any channel with a repetitive
waveform that has a frequency of at least 25 Hz, a duty cycle greater than
0.5%, and an amplitude of at least 10 mV peak- to- peak. Any channels that
do not meet these requirements are turned off.
The trigger source is selected by looking for the first valid waveform
starting with external trigger, then continuing with the lowest number
analog channel up to the highest number analog channel, and finally (if
digital probes are connected) the highest number digital channel.
During Auto Scale, the delay is set to 0.0 seconds, the horizontal time/div
(sweep speed) setting is a function of the input signal (about 2 periods of
the triggered signal on the screen), and the triggering mode is set to Edge.
Compensate Passive Probes

Each oscilloscope passive probe must be compensated to match the input
characteristics of the oscilloscope channel to which it is connected. A
poorly compensated probe can introduce significant measurement errors.
1 Input the Probe Comp signal (see “Input a Waveform" on page 25).
2 Press [Default Setup] to recall the default oscilloscope setup (see “Recall
the Default Oscilloscope Setup" on page 25).
3 Press [Auto Scale] to automatically configure the oscilloscope for the
Probe Comp signal (see “Use Auto Scale" on page 26).
4 Press the channel key to which the probe is connected ([1], [2], etc.).
5 In the Channel Menu, press Probe.
6 In the Channel Probe Menu, press Probe Check; then, follow the
instructions on- screen.

1 Getting Started
If necessary, use a nonmetallic tool (supplied with the probe) to adjust

the trimmer capacitor on the probe for the flattest pulse possible.
On the N2862/63/90 probes, the trimmer capacitor is the yellow
adjustment on the probe tip. On other probes, the trimmer capacitor is
located on the probe BNC connector.
Perfectly compensated
Over compensated
Under compensated
7 Connect probes to all other oscilloscope channels (channel 2 of a

2- channel oscilloscope, or channels 2, 3, and 4 of a 4- channel
oscilloscope).
8 Repeat the procedure for each channel.
Learn the Front Panel Controls and Connectors

On the front panel, key refers to any key (button) you can press.
Softkey specifically refers to the six keys that are directly below the
display. The legend for these keys is directly above them, on the display.
Their functions change as you navigate through the oscilloscope's menus.
For the following figure, refer to the numbered descriptions in the table
that follows.

Getting Started 1
5. Tools keys 6. Trigger controls 7. Horizontal controls 8. Run Control keys
9. [Default Setup] key

10. [Auto Scale] key
11. Additional
4. Entry knob
waveform
controls
3. [Intensity] key
12. Measure controls
2. Softkeys 13. Waveform keys
1. Power switch 14. File keys
15. [Help] key
21. Waveform 20. Digital 19. USB 18. Demo 2, Ground, 17. Analog 16 Vertical controls
generator channel Host and Demo 1 channel
output inputs port terminals inputs
1. Power switch Press once to switch power on; press again to switch power off. See
“Power-On the Oscilloscope" on page 23.
2. Softkeys The functions of these keys change based upon the menus shown on the
display directly above the keys.
The Back
Back/Up key moves up in the softkey menu hierarchy. At the
top of the hierarchy, the Back Back/Up key turns the menus off, and
oscilloscope information is shown instead.
3. [Intensity] key Press the key to illuminate it. When illuminated, turn the Entry knob to
adjust waveform intensity.
You can vary the intensity control to bring out signal detail, much like an
analog oscilloscope.
Digital channel waveform intensity is not adjustable.
More details about using the Intensity control to view signal detail are on
“To adjust waveform intensity" on page 99.

1 Getting Started
4. Entry knob The Entry knob is used to select items from menus and to change values.
The function of the Entry knob changes based upon the current menu
and softkey selections.
Note that the curved arrow symbol above the entry knob
illuminates whenever the entry knob can be used to select a value. Also,
note that when the Entry knob symbol appears on a softkey, you
can use the Entry knob, to select values.
Often, rotating the Entry knob is enough to make a selection. Sometimes,
you can push the Entry knob to enable or disable a selection. Pushing the
Entry knob also makes popup menus disappear.
5. Tools keys The Tools keys consist of:

• [Utility] key — Press this key to access the Utility Menu, which lets
you configure the oscilloscope's I/O settings, use the file explorer, set
preferences, access the service menu, and choose other options. See
Chapter 18, “Utility Settings,” starting on page 223.
• [Quick Action] key — Press this key to perform the selected quick
action: measure all snapshot, print, save, recall, freeze display. and
more. See “Configuring the [Quick Action] Key" on page 238.
• [Analyze] key — Press this key to access analysis features like mask
testing (see Chapter 14, “Mask Testing,” starting on page 187), trigger
level setting, measurement threshold setting, or Video trigger
automatic set up and display.
• [Wave Gen] key — Press this key to access waveform generator
functions. See Chapter 15, “Waveform Generator,” starting on page
199.
6. Trigger controls These controls determine how the oscilloscope triggers to capture data.
See Chapter 9, “Triggers,” starting on page 111 and Chapter 10, “Trigger
Mode/Coupling,” starting on page 133.

Getting Started 1
7. Horizontal The Horizontal controls consist of:

controls • Horizontal scale knob — Turn the knob in the Horizontal section that
is marked to adjust the time/div (sweep speed) setting.

The symbols under the knob indicate that this control has the effect of
spreading out or zooming in on the waveform using the horizontal
scale.
• Horizontal position knob — Turn the knob marked to pan through
the waveform data horizontally. You can see the captured waveform
before the trigger (turn the knob clockwise) or after the trigger (turn
the knob counterclockwise). If you pan through the waveform when
the oscilloscope is stopped (not in Run mode) then you are looking at
the waveform data from the last acquisition taken.
• [Horiz] key — Press this key to open the Horizontal Menu where you
can select XY and Roll modes, enable or disable Zoom, enable or
disable horizontal time/division fine adjustment, and select the
trigger time reference point.
• Zoom key — Press the zoom key to split the oscilloscope
display into Normal and Zoom sections without opening the
Horizontal Menu.
• [Search] key — Lets you search for events in the acquired data.
• [Navigate] keys — Press this key to navigate through captured data
(Time), search events, or segmented memory acquisitions. See
“Navigating the Time Base" on page 53.
For more information see Chapter 2, “Horizontal Controls,” starting on
page 43.
8. Run Control When the [Run/Stop] key is green, the oscilloscope is running, that is,
keys acquiring data when trigger conditions are met. To stop acquiring data,
press [Run/Stop].
When the [Run/Stop] key is red, data acquisition is stopped. To start
acquiring data, press [Run/Stop].
To capture and display a single acquisition (whether the oscilloscope is
running or stopped), press [Single]. The [Single] key is yellow until the
oscilloscope triggers.
For more information, see “Running, Stopping, and Making Single
Acquisitions (Run Control)" on page 141.
9. [Default Setup] Press this key to restore the oscilloscope's default settings (details on
key “Recall the Default Oscilloscope Setup" on page 25).

1 Getting Started
10. [Auto Scale] When you press the [AutoScale] key, the oscilloscope will quickly
key determine which channels have activity, and it will turn these channels
on and scale them to display the input signals. See “Use Auto Scale" on
page 26.
11. Additional The additional waveform controls consist of:
waveform • [Math] key — provides access to math (add, subtract, etc.) waveform
controls functions. See Chapter 4, “Math Waveforms,” starting on page 63.
• [Ref] key — provides access to reference waveform functions.
Reference waveforms are saved waveforms that can be displayed and
compared against other analog channel or math waveforms. See
Chapter 5, “Reference Waveforms,” starting on page 75.
• [Digital] key — Press this key to turn the digital channels on or off
(the arrow to the left will illuminate).
When the arrow to the left of the [Digital] key is illuminated, the
upper multiplexed knob selects (and highlights in red) individual
digital channels, and the lower multiplexed knob positions the
selected digital channel.
If a trace is repositioned over an existing trace the indicator at the left
edge of the trace will change from Dn designation (where n is a one
digit channel number from 0 to 7) to D*. The "*" indicates that two
channels are overlaid.
You can rotate the upper knob to select an overlaid channel, then
rotate the lower knob to position it just as you would any other
channel.
For more information on digital channels see Chapter 6, “Digital
Channels,” starting on page 79.
• [Serial] key — This key is not currently used with the 2000 X-Series
oscilloscopes.
• Multiplexed scale knob — This scale knob is used with Math, Ref, or
Digital waveforms, whichever has the illuminated arrow to the left.
For math and reference waveforms, the scale knob acts like an analog
channel vertical scale knob.
• Multiplexed position knob — This position knob is used with Math,
Ref, or Digital waveforms, whichever has the illuminated arrow to the
left. For math and reference waveforms, the position knob acts like an
analog channel vertical position knob.

Getting Started 1
12. Measure The measure controls consist of:

controls • Cursors knob — Push this knob select cursors from a popup menu.
Then, after the popup menu closes (either by timeout or by pushing
the knob again), rotate the knob to adjust the selected cursor
position.
• [Cursors] key — Press this key to open a menu that lets you select
the cursors mode and source.
• [Meas] key — Press this key to access a set of predefined
measurements. See Chapter 13, “Measurements,” starting on page
167.
13. Waveform keys The [Acquire] key lets you select Normal, Peak Detect, Averaging, or
High Resolution acquisition modes (see “Selecting the Acquisition
Mode" on page 147) and use segmented memory (see “Acquiring to
Segmented Memory" on page 153).
The [Display] key lets you access the menu where you can enable
persistence (see “To set or clear persistence" on page 101), clear the
display, and adjust the display grid (graticule) intensity (see “To adjust
the grid intensity" on page 103).
14. File keys Press the [Save/Recall] key to save or recall a waveform or setup. See
Chapter 16, “Save/Recall (Setups, Screens, Data),” starting on page 205.
The [Print] key opens the Print Configuration Menu so you can print the
displayed waveforms. See Chapter 17, “Print (Screens),” starting on page
219.
15. [Help] key Opens the Help Menu where you can display overview help topics and
select the Language. See also “Access the Built-In Quick Help" on
page 40.

1 Getting Started
16. Vertical The Vertical controls consist of:

controls • Analog channel on/off keys — Use these keys to switch a channel on
or off, or to access a channel's menu in the softkeys. There is one
channel on/off key for each analog channel.
• Vertical scale knob — There are knobs marked for each

channel. Use these knobs to change the vertical sensitivity (gain) of
each analog channel.
• Vertical position knobs — Use these knobs to change a channel's
vertical position on the display. There is one Vertical Position control
for each analog channel.
• [Label] key — Press this key to access the Label Menu, which lets
you enter labels to identify each trace on the oscilloscope display. See
Chapter 8, “Labels,” starting on page 105.
For more information, see Chapter 3, “Vertical Controls,” starting on
page 55.
17. Analog channel Attach oscilloscope probes or BNC cables to these BNC connectors.
inputs In the InfiniiVision 2000 X-Series oscilloscopes, the analog channel
inputs have 1 MΩ impedance.
Also, there is no automatic probe detection, so you must properly set the
probe attenuation for accurate measurement results. See “To specify the
probe attenuation" on page 60.
18. Demo 2, • Demo 2 terminal — This terminal outputs the Probe Comp signal
Ground, and which helps you match a probe's input capacitance to the
Demo 1 oscilloscope channel to which it is connected. See “Compensate
terminals Passive Probes" on page 27. With certain licensed features, the
oscilloscope can also output demo or training signals on this terminal.
• Ground terminal — Use the ground terminal for oscilloscope probes
connected to the Demo 1 or Demo 2 terminals.
• Demo 1 terminal — With certain licensed features, the oscilloscope
can output demo or training signals on this terminal.

Getting Started 1
19. USB Host port This port is for connecting USB mass storage devices or printers to the
oscilloscope.
Connect a USB compliant mass storage device (flash drive, disk drive,
etc.) to save or recall oscilloscope setup files and reference waveforms
or to save data and screen images. See Chapter 16, “Save/Recall
(Setups, Screens, Data),” starting on page 205.
To print, connect a USB compliant printer. For more information about
printing see Chapter 17, “Print (Screens),” starting on page 219.
You can also use the USB port to update the oscilloscope's system
software when updates are available.
You do not need to take special precautions before removing the USB
mass storage device from the oscilloscope (you do not need to "eject"
it). Simply unplug the USB mass storage device from the oscilloscope
when the file operation is complete.
CAUTION: Do not connect a host computer to the oscilloscope's

USB host port. Use the device port. A host computer sees the
oscilloscope as a device, so connect the host computer to the
oscilloscope's device port (on the rear panel). See “I/O Interface
Settings" on page 223.
There is a second USB host port on the back panel.
20. Digital channel Connect the digital probe cable to this connector (MSO models only). See
inputs Chapter 6, “Digital Channels,” starting on page 79.
21. Waveform Outputs sine, square, ramp, pulse, DC, or noise on the Gen Out BNC.
generator Press the [Wave Gen] key to set up the waveform generator. See
output Chapter 15, “Waveform Generator,” starting on page 199.
Front Panel Overlays for Different Languages

Front panel overlays, which have translations for the English front panel
keys and label text, are available in 10 languages. The appropriate overlay
is included when the localization option is chosen at time of purchase.
To install a front panel overlay:
1 Gently pull on the front panel knobs to remove them.
2 Insert the overlay's side tabs into the slots on the front panel.

1 Getting Started
3 Reinstall the front panel knobs.

Front panel overlays may be ordered from "www.parts.agilent.com" using
the following part numbers:
Language 2 Channel Overlay 4 Channel Overlay
French 75019-94324 75019-94316

German 75019-94326 75019-94318
Italian 75019-94323 75019-94331
Japanese 75019-94311 75019-94312

Korean 75019-94329 75019-94321
Portuguese 75019-94327 75019-94319
Russian 75019-94322 75019-94315

Simplified Chinese 75019-94328 75019-94320
Spanish 75019-94325 75019-94317

Traditional Chinese 75019-94330 75019-94310

Getting Started 1
Learn the Rear Panel Connectors

For the following figure, refer to the numbered descriptions in the table
that follows.
8. USB Device port

3. LAN/VGA
7. USB Host port option module
6. EXT TRIG IN
connector
5. Calibration
protect
button 3. GPIB
option module
4. TRIG OUT
connector
L6GC>C</B6>CI6>C
<GDJC9ID 6KD>9
:A:8IG>8H=D8@
3. Module slot
s &%%"&'%K!*%$+%$)%%=o
s &%%"')%K!*%$+%=o
&%% LViihB6M
2. Kensington lock hole
1. Power cord connector
1. Power cord Attach the power cord here.

connector
2. Kensington This is where you can attach a Kensington lock for securing the
lock hole instrument.
3. Module slot No modules are included with the oscilloscope.

A DSOXLAN LAN/VGA module may be ordered and installed separately.
• LAN port — lets you communicate with the oscilloscope and use the
Remote Front Panel feature using the LAN port. See Chapter 19,
“Web Interface,” starting on page 241 and “Accessing the Web
Interface" on page 242.
• VGA video output — lets you connect an external monitor or projector
to provide a larger display or to provide a display at a viewing position
away from the oscilloscope.
The oscilloscope's built-in display remains on even when an external
display is connected. The video output connector is always active.
For optimal video quality and performance, we recommend you use a
shielded video cable with ferrite cores.
Also, a DSOXGPIB GPIB module may be ordered and installed separately.

1 Getting Started
4. TRIG OUT Trigger output BNC connector. See “Setting the Rear Panel TRIG OUT
connector Source" on page 232.
5. Calibration See “To perform user calibration" on page 234.
protect button
6. EXT TRIG IN External trigger input BNC connector. See “External Trigger Input" on
connector page 138 for an explanation of this feature.
8. USB Device This port is for connecting the oscilloscope to a host PC. You can issue
port remote commands from a host PC to the oscilloscope via the USB device
port. See “Remote Programming with Agilent IO Libraries" on page 247.
7. USB Host port This port functions identically to the USB host port on the front panel.
USB Host Port is used for saving data from the oscilloscope and loading
software updates. See also USB Host port (see page 35).
Learn the Oscilloscope Display

The oscilloscope display contains acquired waveforms, setup information,
measurement results, and the softkey definitions.

Getting Started 1
Analog channel Trigger point, Delay Time/ Run/Stop Trigger Trigger

sensitivity time reference time div status type source
Status line Trigger level or

digital threshold
Trigger level
Information area
Analog
channels
and ground
levels
Cursors defining
Digital channels measurement
Measurements
Menu line
Softkeys
Figure 1 Interpreting the oscilloscope display
Status line The top line of the display contains vertical, horizontal, and trigger setup
information.
Display area The display area contains the waveform acquisitions, channel identifiers, and
analog trigger, and ground level indicators. Each analog channel's information
appears in a different color.
Signal detail is displayed using 256 levels of intensity. For more information
about viewing signal detail see “To adjust waveform intensity" on page 99.
For more information about display modes see Chapter 7, “Display Settings,”
starting on page 99.
Information area The information area normally contains acquisition, analog channel,
automatic measurement, and cursor results.
Menu line This line normally contains menu name or other information associated with
the selected menu.

1 Getting Started
Softkey labels These labels describe softkey functions. Typically, softkeys let you set up
additional parameters for the selected mode or menu.
Pressing the Back Back/Up key at the top of the menu hierarchy turns off
softkey labels and displays additional status information describing channel
offset and other configuration parameters.
Access the Built-In Quick Help

To view Quick 1 Press and hold the key or softkey for which you would like to view
Help help.
Quick Help
message
Press and hold front panel key or softkey

(or right-click softkey when using web browser remote front panel).
Quick Help remains on the screen until another key is pressed or a knob
is turned.

Getting Started 1
To select the user To select the user interface and Quick Help language:
interface and 1 Press [Help], then press the Language softkey.
Quick Help
language 2 Repeatedly press and release the Language softkey or rotate the Entry
knob until the desired language is selected.
The following languages are available: English, French, German, Italian,
Japanese, Korean, Portuguese, Russian, Simplified Chinese, Spanish, and
Traditional Chinese.

1 Getting Started

User's Guide
2
Horizontal Controls
To adjust the horizontal (time/div) scale 44
To adjust the horizontal delay (position) 45
Panning and Zooming Single or Stopped Acquisitions 46
To change the horizontal time mode (Normal, XY, or Roll) 47
To display the zoomed time base 50
To change the horizontal scale knob's coarse/fine adjustment setting 52
To position the time reference (left, center, right) 52
Navigating the Time Base 53
The horizontal controls include:

• The horizontal scale and position knobs.
• The [Horiz] key for accessing the Horizontal Menu.
• The zoom key for quickly enabling/disabling the split- screen zoom
display.
• The [Search] key for finding events on analog channels.
• The [Navigate] keys for navigating time, search events, or segmented
memory acquisitions.
The following figure shows the Horizontal Menu which appears after
pressing the [Horiz] key.
43
Trigger Time Delay Time/ Trigger Trigger level

point reference time div source or threshold
Sample rate
XY or Roll
mode
Normal Zoomed Fine Time

time mode time base control reference
Figure 2 Horizontal Menu
The Horizontal Menu lets you select the time mode (Normal, XY, or Roll),
enable Zoom, set the time base fine control (vernier), and specify the time
reference.
The current sample rate is displayed above the Fine and Time Ref softkeys.
To adjust the horizontal (time/div) scale
1 Turn the large horizontal scale (sweep speed) knob marked to

change the horizontal time/div setting.

Horizontal Controls 2
Notice how the time/div information in the status line changes.

The ∇ symbol at the top of the display indicates the time reference point.
The horizontal scale knob works (in the Normal time mode) while
acquisitions are running or when they are stopped. When running,
adjusting the horizontal scale knob changes the sample rate. When
stopped, adjusting the horizontal scale knob lets you zoom into acquired
data. See "Panning and Zooming Single or Stopped Acquisitions" on
page 46.
Note that the horizontal scale knob has a different purpose in the Zoom
display. See "To display the zoomed time base" on page 50.
To adjust the horizontal delay (position)

1 Turn the horizontal delay (position) knob ( ).
The trigger point moves horizontally, pausing at 0.00 s (mimicking a
mechanical detent), and the delay value is displayed in the status line.
Changing the delay time moves the trigger point (solid inverted triangle)
horizontally and indicates how far it is from the time reference point
(hollow inverted triangle ∇). These reference points are indicated along
the top of the display grid.
Figure 2 shows the trigger point with the delay time set to 200 µs. The
delay time number tells you how far the time reference point is located
from the trigger point. When delay time is set to zero, the delay time
indicator overlays the time reference indicator.
All events displayed left of the trigger point happened before the trigger
occurred. These events are called pre- trigger information, and they show
events that led up to the trigger point.
Everything to the right of the trigger point is called post- trigger
information. The amount of delay range (pre- trigger and post- trigger
information) available depends on the time/div selected and memory
depth.
The horizontal position knob works (in the Normal time mode) while
acquisitions are running or when they are stopped. When running,
adjusting the horizontal scale knob changes the sample rate. When

stopped, adjusting the horizontal scale knob lets you zoom into acquired
data. See "Panning and Zooming Single or Stopped Acquisitions" on
page 46.
Note that the horizontal position knob has a different purpose in the
Zoom display. See "To display the zoomed time base" on page 50.
Panning and Zooming Single or Stopped Acquisitions

When the oscilloscope is stopped, use the horizontal scale and position
knobs to pan and zoom your waveform. The stopped display may contain
several acquisitions worth of information, but only the last acquisition is
available for pan and zoom.
The ability to pan (move horizontally) and scale (expand or compress
horizontally) an acquired waveform is important because of the additional
insight it can reveal about the captured waveform. This additional insight
is often gained from seeing the waveform at different levels of abstraction.
You may want to view both the big picture and the specific little picture
details.
The ability to examine waveform detail after the waveform has been
acquired is a benefit generally associated with digital oscilloscopes. Often
this is simply the ability to freeze the display for the purpose of
measuring with cursors or printing the screen. Some digital oscilloscopes
go one step further by including the ability to further examine the signal
details after acquiring them by panning through the waveform and
changing the horizontal scale.
There is no limit imposed on the scaling ratio between the time/div used
to acquire the data and the time/div used to view the data. There is,
however, a useful limit. This useful limit is somewhat a function of the
signal you are analyzing.
Zooming into stopped acquisitions

NOTE
The screen will still contain a relatively good display if you zoom-in horizontally by a factor
of 1000 and zoom-in vertically by a factor of 10 to display the information from where it was
acquired. Remember that you can only make automatic measurements on displayed data.

To change the horizontal time mode (Normal, XY, or Roll)

1 Press [Horiz].
2 In the Horizontal Menu, press Time Mode; then, select:
• Normal — the normal viewing mode for the oscilloscope.
In the Normal time mode, signal events occurring before the trigger
are plotted to the left of the trigger point (▼) and signal events after
the trigger plotted to the right of the trigger point.
• XY — XY mode changes the display from a volts- versus- time display
to a volts- versus- volts display. The time base is turned off. Channel 1
amplitude is plotted on the X- axis and Channel 2 amplitude is
plotted on the Y- axis.
You can use XY mode to compare frequency and phase relationships
between two signals. XY mode can also be used with transducers to
display strain versus displacement, flow versus pressure, volts versus
current, or voltage versus frequency.
Use the cursors to make measurements on XY mode waveforms.
For more information about using XY mode for measurements, refer
to "XY Time Mode" on page 48.
• Roll — causes the waveform to move slowly across the screen from
right to left. It only operates on time base settings of 50 ms/div and
slower. If the current time base setting is faster than the 50 ms/div
limit, it will be set to 50 ms/div when Roll mode is entered.
In Roll mode there is no trigger. The fixed reference point on the
screen is the right edge of the screen and refers to the current
moment in time. Events that have occurred are scrolled to the left of
the reference point. Since there is no trigger, no pre- trigger
information is available.
If you would like to pause the display in Roll mode press the [Single]
key. To clear the display and restart an acquisition in Roll mode,
press the [Single] key again.
Use Roll mode on low- frequency waveforms to yield a display much
like a strip chart recorder. It allows the waveform to roll across the
display.

XY Time Mode
The XY time mode converts the oscilloscope from a volts- versus- time
display to a volts- versus- volts display using two input channels. Channel 1
is the X- axis input, channel 2 is the Y- axis input. You can use various
transducers so the display could show strain versus displacement, flow
versus pressure, volts versus current, or voltage versus frequency.
Example This exercise shows a common use of the XY display mode by measuring
the phase difference between two signals of the same frequency with the
Lissajous method.
1 Connect a sine wave signal to channel 1, and a sine wave signal of the
same frequency but out of phase to channel 2.
2 Press the [AutoScale] key, press the [Horiz] key; then, press Time Mode
and select "XY".
3 Center the signal on the display with the channel 1 and 2 position ( )
knobs. Use the channel 1 and 2 volts/div knobs and the channel 1 and
2 Fine softkeys to expand the signal for convenient viewing.
The phase difference angle (θ) can be calculated using the following
formula (assuming the amplitude is the same on both channels):
A or C
sinθ = B D
Signal must
be centered in
“ X”
D A B
Measuring Signals 90 degrees Signals

phase difference out of phase in phase
Figure 3 XY time mode signals, centered on display

4 Press the [Cursors] key.

5 Set the Y2 cursor to the top of the signal, and set Y1 to the bottom of
the signal.
Note the ∆Y value at the bottom of the display. In this example, we are
using the Y cursors, but you could have used the X cursors instead.
6 Move the Y1 and Y2 cursors to the intersection of the signal and the Y
axis. Again, note the ∆Y value.
Figure 4 Phase difference measurements, automatic and using cursors
7 Calculate the phase difference using the formula below.

For example, if the first ∆Y value is 1.688 and the second ∆Y value is
1.031:
sinθ = second Δ Y 1.031

first Δ Y = 1.688 ; θ = 37.65 degrees of phase shift

Z-Axis Input in XY Display Mode (Blanking)

NOTE
When you select the XY display mode, the time base is turned off. Channel 1 is the X-axis
input, channel 2 is the Y-axis input, and the rear panel EXT TRIG IN is the Z-axis input. If you
only want to see portions of the Y versus X display, use the Z-axis input. Z-axis turns the
trace on and off (analog oscilloscopes called this Z-axis blanking because it turned the
beam on and off). When Z is low (<1.4 V), Y versus X is displayed; when Z is high (>1.4 V),
the trace is turned off.
To display the zoomed time base

Zoom, formerly called Delayed sweep mode, is a horizontally expanded
version of the normal display. When Zoom is selected, the display divides
in half. The top half of the display shows the normal time/div window and
the bottom half displays a faster Zoom time/div window.
The Zoom window is a magnified portion of the normal time/div window.
You can use Zoom to locate and horizontally expand part of the normal
window for a more detailed (higher- resolution) analysis of signals.
To turn on (or off) Zoom:
1 Press the zoom key (or press the [Horiz] key and then the Zoom
softkey).

These markers show the Time/div Time/div Delay time

beginning and end of the for zoomed for normal momentarily displays
Zoom window window window when the Horizontal
position knob is turned
Normal
window
Signal
anomaly
expanded
in zoom
window
Zoom
window
Select
Zoom
The area of the normal display that is expanded is outlined with a box
and the rest of the normal display is ghosted. The box shows the portion
of the normal sweep that is expanded in the lower half.
To change the time/div for the Zoom window, turn the horizontal scale
(sweep speed) knob. As you turn the knob, the zoomed window time/div
is highlighted in the status line above the waveform display area. The
Horizontal scale (sweep speed) knob controls the size of the box.
The Horizontal position (delay time) knob sets the left- to- right position of
the zoom window. The delay value, which is the time displayed relative to
the trigger point) is momentarily displayed in the upper- right portion of
the display when the delay time ( ) knob is turned.

Negative delay values indicate you're looking at a portion of the waveform

before the trigger event, and positive values indicate you're looking at the
waveform after the trigger event.
To change the time/div of the normal window, turn off Zoom; then, turn
the horizontal scale (sweep speed) knob.
For information about using zoom mode for measurements, refer to "To
isolate a pulse for Top measurement" on page 173 and "To isolate an event
for frequency measurement" on page 180.
To change the horizontal scale knob's coarse/fine adjustment setting

1 Push the horizontal scale knob (or press [Horiz] > Fine) to toggle between
fine and coarse adjustment of the horizontal scale.
When Fine is enabled, turning the horizontal scale knob changes the
time/div (displayed in the status line at the top of the display) in smaller
increments. The time/div remains fully calibrated when Fine is on.
When Fine is turned off, the Horizontal scale knob changes the time/div
setting in a 1- 2- 5 step sequence.
To position the time reference (left, center, right)

Time reference is the reference point on the display for delay time
(horizontal position).
1 Press [Horiz].
2 In the Horizontal Menu, press Time Ref; then, select:
• Left — the time reference is set to one major division from the left
edge of the display.
• Center — the time reference is set to the center of the display.
• Right — the time reference is set to one major division from the right
edge of the display.
A small hollow triangle (∇) at the top of the display grid marks the
position of the time reference. When delay time is set to zero, the trigger
point indicator (▼) overlays the time reference indicator.

The time reference position sets the initial position of the trigger event
within acquisition memory and on the display, with delay set to 0.
Turning the Horizontal scale (sweep speed) knob expands or contracts the
waveform about the time reference point (∇). See "To adjust the horizontal
(time/div) scale" on page 44.
Turning the Horizontal position ( ) knob in Normal mode (not Zoom)
moves the trigger point indicator (▼) to the left or right of the time
reference point (∇). See "To adjust the horizontal delay (position)" on
page 45.
Navigating the Time Base

You can use the [Navigate] key and controls to navigate through:
• Captured data (see "To navigate time" on page 53).
• Segments, when segmented memory acquisitions are turned on (see "To
navigate segments" on page 53).
To navigate time
When acquisitions are stopped, you can use the navigation controls to play
through the captured data.
1 Press [Navigate].
2 In the Navigate Menu, press Navigate; then, select Time.
3 Press the navigation keys to play backward, stop, or play

forward in time. You can press the or keys multiple times to
speed up the playback. There are three speed levels.
To navigate segments
When the segmented memory acquisition is enabled and acquisitions are
stopped, you can use the navigation controls to play through the acquired
segments.
1 Press [Navigate].
2 In the Navigate Menu, press Navigate; then, select Segments.

3 Press Play Mode; then, select:

• Manual — to play through segments manually.
In the Manual play mode:
• Press the back and forward keys to go to the previous or

next segment.
• Press the softkey to go to the first segment.
• Press the softkey to go to the last segment.

• Auto — to play through segments in an automated fashion.
In the Auto play mode:
• Press the navigation keys to play backward, stop, or

play forward in time. You can press the or keys multiple
times to speed up the playback. There are three speed levels.

User's Guide
3
Vertical Controls
To turn waveforms on or off (channel or math) 56
To adjust the vertical scale 57
To adjust the vertical position 57
To specify channel coupling 57
To specify bandwidth limiting 58
To change the vertical scale knob's coarse/fine adjustment setting 58
To invert a waveform 59
Setting Analog Channel Probe Options 59
The vertical controls include:

• The vertical scale and position knobs for each analog channel.
• The channel keys for turning a channel on or off and accessing the
channel's softkey menu.
The following figure shows the Channel 1 Menu that appears after
pressing the [1] channel key.
55
3 Vertical Controls
Channel, Trigger Trigger level

Volts/div source or threshold
Channel 1
ground
level
Channel 2
ground
level
The ground level of the signal for each displayed analog channel is
identified by the position of the icon at the far- left side of the display.
To turn waveforms on or off (channel or math)

1 Press an analog channel key turn the channel on or off (and to display
the channel's menu).
When a channel is on, its key is illuminated.
Turning channels off

NOTE
You must be viewing the menu for a channel before you can turn it off. For example, if
channel 1 and channel 2 are turned on and the menu for channel 2 is being displayed, to
turn channel 1 off, press [1] to display the channel 1 menu; then, press [1] again to turn
channel 1 off.

Vertical Controls 3
To adjust the vertical scale
1 Turn the large knob above the channel key marked to set the
vertical scale (volts/division) for the channel.
The vertical scale knob changes the analog channel scale in a 1- 2- 5 step
sequence (with a 1:1 probe attached) unless fine adjustment is enabled
(see "To change the vertical scale knob's coarse/fine adjustment setting" on
page 58).
The analog channel Volts/Div value is displayed in the status line.
The default mode for expanding the signal when you turn the
volts/division knob is vertical expansion about the ground level of the
channel; however, you can change this to expand about the center of the
display. See "To choose "expand about" center or ground" on page 229.
To adjust the vertical position
1 Turn the small vertical position knob ( ) to move the channel's

waveform up or down on the display.
The voltage value momentarily displayed in the upper right portion of the
display represents the voltage difference between the vertical center of the
display and the ground level ( ) icon. It also represents the voltage at
the vertical center of the display if vertical expansion is set to expand
about ground (see "To choose "expand about" center or ground" on
page 229).
To specify channel coupling

Coupling changes the channel's input coupling to either AC (alternating
current) or DC (direct current).

3 Vertical Controls
If the channel is DC coupled, you can quickly measure the DC component of the signal by
TIP simply noting its distance from the ground symbol.
If the channel is AC coupled, the DC component of the signal is removed, allowing you to
use greater sensitivity to display the AC component of the signal.
1 Press the desired channel key.

2 In the Channel Menu, press the Coupling softkey to select the input
channel coupling:
• DC — DC coupling is useful for viewing waveforms as low as 0 Hz
that do not have large DC offsets.
• AC — AC coupling is useful for viewing waveforms with large DC
offsets.
AC coupling places a 10 Hz high- pass filter in series with the input
waveform that removes any DC offset voltage from the waveform.
Note that Channel Coupling is independent of Trigger Coupling. To change
trigger coupling see "To select the trigger coupling" on page 136.
To specify bandwidth limiting

2 In the Channel Menu, press the BW Limit softkey to enable or disable
bandwidth limiting.
When bandwidth limit is on, the maximum bandwidth for the channel is
approximately 20 MHz. For waveforms with frequencies below this, turning
bandwidth limit on removes unwanted high frequency noise from the
waveform. The bandwidth limit also limits the trigger signal path of any
channel that has BW Limit turned on.
To change the vertical scale knob's coarse/fine adjustment setting

1 Push the channel's vertical scale knob (or press the channel key and
then the Fine softkey in the Channel Menu) to toggle between fine and
coarse adjustment of the vertical scale.

Vertical Controls 3
When Fine adjustment is selected, you can change the channel's vertical
sensitivity in smaller increments. The channel sensitivity remains fully
calibrated when Fine is on.
The vertical scale value is displayed in the status line at the top of the
display.
When Fine is turned off, turning the volts/division knob changes the
channel sensitivity in a 1- 2- 5 step sequence.
To invert a waveform
2 In the Channel Menu, press the Invert softkey to invert the selected
channel.
When Invert is selected, the voltage values of the displayed waveform are
inverted.
Invert affects how a channel is displayed. However, when using basic
triggers, the oscilloscope attempts to maintain the same trigger point by
changing trigger settings.
Inverting a channel also changes the result of any math function selected
in the Waveform Math Menu or any measurement.
Setting Analog Channel Probe Options

1 Press the probe's associated channel key.
2 In the Channel Menu, press the Probe softkey to display the Channel
Probe Menu.
This menu lets you select additional probe parameters such as
attenuation factor and units of measurement for the connected probe.

3 Vertical Controls
The Probe Check softkey guides you through the process of compensating
passive probes (such as the N2862A/B, N2863A/B, N2889A, N2890A,
10073C, 10074C, or 1165A probes).
See Also • "To specify the channel units" on page 60
• "To specify the probe attenuation" on page 60
• "To specify the probe skew" on page 61
To specify the channel units

1 Press the probe's associated channel key.
3 In the Channel Probe Menu, press Units; then, select:
• Volts — for a voltage probe.
• Amps — for a current probe.
Channel sensitivity, trigger level, measurement results, and math functions
will reflect the measurement units you have selected.
To specify the probe attenuation

The probe attenuation factor must be set properly for accurate
measurement results.
To set the probe attenuation factor:
1 Press the channel key.
2 Press the Probe softkey until you have selected how you want to specify
the attenuation factor, choosing either Ratio or Decibels.
3 Turn the Entry knob to set the attenuation factor for the connected
probe.
When measuring voltage values, the attenuation factor can be set from
0.1:1 to 1000:1 in a 1- 2- 5 sequence.
When measuring current values with a current probe, the attenuation
factor can be set from 10 V/A to 0.001 V/A.
When specifying the attenuation factor in decibels, you can select values
from - 20 dB to 60 dB.

Vertical Controls 3
If Amps is chosen as the units and a manual attenuation factor is chosen,

then the units as well as the attenuation factor are displayed above the
Probe softkey.
To specify the probe skew

When measuring time intervals in the nanoseconds (ns) range, small
differences in cable length can affect the measurement. Use Skew to
remove cable- delay errors between any two channels.
1 Probe the same point with both probes.
2 Press one of the probes associated channel key.
4 In the Channel Probe Menu, press Skew; then, select the desired skew
value.
Each analog channel can be adjusted ±100 ns in 10 ps increments for a
total of 200 ns difference.
The skew setting is not affected by pressing [Default Setup] or [Auto Scale].

3 Vertical Controls

User's Guide
4
Math Waveforms
To display math waveforms 63
To perform a transform function on an arithmetic operation 64
To adjust the math waveform scale and offset 65
Add or Subtract 66
Multiply 65
FFT Measurement 67
Units for Math Waveforms 74
Math functions can be performed on analog channels. The resulting math

waveform is displayed in light purple.
You can use a math function on a channel even if you choose not to
display the channel on- screen.
You can:
• Perform an arithmetic operation (add, subtract, or multiply) on
channels 1 and 2 or on channels 3 and 4.
• Perform a transform function (FFT) on the signal acquired on an analog
channel.
• Perform a transform function on the result of an arithmetic operation.
To display math waveforms

1 Press the [Math] key on the front panel to display the Waveform Math
Menu.
63
4 Math Waveforms
2 If f(t) is not already shown on the Function softkey, press the Function
sofkey and select f(t): Displayed.
3 Use the Operator softkey to select an operator.
For more information on the operators, see:
• "Add or Subtract" on page 66
• "Multiply" on page 65
• "FFT Measurement" on page 67
4 Use the Source 1 softkey to select the analog channel on which to
perform math. You can rotate the Entry knob or repetitively press the
Source 1 softkey to make your selection. If you choose a transform
function (FFT) the result is displayed.
5 If you select an arithmetic operator, use the Source 2 softkey to select
the second source for the arithmetic operation. The result is displayed.
6 To re- size and reposition the math waveform, see "To adjust the math
waveform scale and offset" on page 65.
Math Operating Hints

TIP
If the analog channel or math function is clipped (not fully displayed on screen) the
resulting displayed math function will also be clipped.
Once the function is displayed, the analog channel(s) may be turned off for better viewing
of the math waveform.
The vertical scaling and offset of each math function can be adjusted for ease of viewing
and measurement considerations.
The math function waveform can be measured using [Cursors] and/or [Meas].
To perform a transform function on an arithmetic operation

To perform a transform function (FFT) on an arithmetic operation (add,
subtract, or multiply):
1 Press the Function softkey and select g(t): Internal.

Math Waveforms 4
2 Use the Operator, Source 1, and Source 2 softkeys to set up an arithmetic

operation.
3 Press the Function softkey and select f(t): Displayed.
4 Use the Operator softkey to select a transform function (FFT).
5 Press the Source 1 softkey and select g(t) as the source. Note that g(t) is
only available when you select a transform function in the previous
step.
To adjust the math waveform scale and offset

1 Make sure the multiplexed scale and position knobs to the right of the
[Math] key are selected for the math waveform.
If the arrow to the left of the [Math] key is not illuminated, press the
key.
2 Use the multiplexed scale and position knobs just to the right of the
[Math] key to re- size and reposition the math waveform.
Math Scale and Offset are Set Automatically

NOTE
Any time the currently displayed math function definition is changed, the function is
automatically scaled for optimum vertical scale and offset. If you manually set scale and
offset for a function, select a new function, then select the original function, the original
function will be automatically rescaled.
See Also • "Units for Math Waveforms" on page 74
Multiply
When you select the multiply math function, the Source 1 and Source 2
values are multiplied point by point, and the result is displayed.
Multiply is useful for seeing power relationships when one of the channels
is proportional to the current.

4 Math Waveforms
Figure 5 Example of Multiply Channel 1 by Channel 2
Add or Subtract
When you select add or subtract, the Source 1 and Source 2 values are
added or subtracted point by point, and the result is displayed.
You can use subtract to make a differential measurement or to compare
two waveforms.
If your waveforms' DC offsets are larger than the dynamic range of the
oscilloscope's input channels you will need to use a differential probe
instead.

Math Waveforms 4
Figure 6 Example of Subtract Channel 2 from Channel 1
FFT Measurement
FFT is used to compute the fast Fourier transform using analog input
channels or an arithmetic operation g(t). FFT takes the digitized time
record of the specified source and transforms it to the frequency domain.
When the FFT function is selected, the FFT spectrum is plotted on the
oscilloscope display as magnitude in dBV versus frequency. The readout
for the horizontal axis changes from time to frequency (Hertz) and the
vertical readout changes from volts to dB.
Use the FFT function to find crosstalk problems, to find distortion
problems in analog waveforms caused by amplifier non- linearity, or for
adjusting analog filters.
To display a FFT waveform:
1 Press the [Math] key, press the Function softkey and select f(t), press the
Operator softkey and select FFT.

4 Math Waveforms
• Source 1 — selects the source for the FFT. (See "To perform a
transform function on an arithmetic operation" on page 64 for
information about using g(t) as the source.)
• Span — sets the overall width of the FFT spectrum that you see on
the display (left to right). Divide span by 10 to calculate the number
of Hertz per division. It is possible to set Span above the maximum
available frequency, in which case the displayed spectrum will not
take up the whole screen. Press the Span softkey, then turn the Entry
knob to set the desired frequency span of the display.
• Center — sets the FFT spectrum frequency represented at the center
vertical grid line of the display. It is possible to set the Center to
values below half the span or above the maximum available
frequency, in which case the displayed spectrum will not take up the
whole screen. Press the Center softkey, then turn the Entry knob to
set the desired center frequency of the display.
• Scale — lets you set your own vertical scale factors for FFT expressed
in dB/div (decibels/division). See "To adjust the math waveform scale
and offset" on page 65.
• Offset — lets you set your own offset for the FFT. The offset value is
in dB and is represented by the center horizontal grid line of the
display. See "To adjust the math waveform scale and offset" on
page 65.
• More FFT — displays the More FFT Settings Menu.
2 Press the More FFT softkey to display additional FFT settings.
• Window— selects a window to apply to your FFT input signal:

• Hanning — window for making accurate frequency measurements or
for resolving two frequencies that are close together.
• Flat Top — window for making accurate amplitude measurements of
frequency peaks.

Math Waveforms 4
• Rectangular — good frequency resolution and amplitude accuracy,

but use only where there will be no leakage effects. Use on
self- windowing waveforms such as pseudo- random noise, impulses,
sine bursts, and decaying sinusoids.
• Blackman Harris — window reduces time resolution compared to a
rectangular window, but improves the capacity to detect smaller
impulses due to lower secondary lobes.
• Vertical Units — lets you select Decibels or V RMS as the units for the
FFT vertical scale.
• Auto Setup — sets the frequency Span and Center to values that will
cause the entire available spectrum to be displayed. The maximum
available frequency is half the FFT sample rate, which is a function
of the time per division setting. The FFT resolution is the quotient of
the sampling rate and the number of FFT points (fS/N). The current
FFT Resolution is displayed above the softkeys.
Scale and offset considerations

NOTE
If you do not manually change the FFT scale or offset settings, when you turn the horizontal
scale knob, the span and center frequency settings will automatically change to allow
optimum viewing of the full spectrum.
If you do manually set scale or offset, turning the horizontal scale knob will not change the
span or center frequency settings, allowing you see better detail around a specific
frequency.
Pressing the FFT Auto Setup softkey will automatically rescale the waveform and span and
center will again automatically track the horizontal scale setting.
3 To make cursor measurements, press the [Cursors] key and set the
Source softkey to Math: f(t).
Use the X1 and X2 cursors to measure frequency values and difference
between two frequency values (∆X). Use the Y1 and Y2 cursors to
measure amplitude in dB and difference in amplitude (∆Y).
4 To make other measurements, press the [Meas] key and set the Source
softkey to Math: f(t).

4 Math Waveforms
You can make peak- to- peak, maximum, minimum, and average dB
measurements on the FFT waveform. You can also find the frequency
value at the first occurrence of the waveform maximum by using the X
at Max Y measurement.
The following FFT spectrum was obtained by connecting a 4 V, 75 kHz
square wave to channel 1. Set the horizontal scale to 50 µs/div, vertical
sensitivity to 1 V/div, Units/div to 20 dBV, Offset to - 60.0 dBV, Center
frequency to 250 kHz, frequency Span to 500 kHz, and window to
Hanning.
See Also • "To perform a transform function on an arithmetic operation" on

page 64
• "FFT Measurement Hints" on page 71
• "FFT Units" on page 72
• "FFT DC Value" on page 72
• "FFT Aliasing" on page 72
• "FFT Spectral Leakage" on page 74
• "Units for Math Waveforms" on page 74

Math Waveforms 4
FFT Measurement Hints

The number of points acquired for the FFT record can be up to 65,536,
and when frequency span is at maximum, all points are displayed. Once
the FFT spectrum is displayed, the frequency span and center frequency
controls are used much like the controls of a spectrum analyzer to
examine the frequency of interest in greater detail. Place the desired part
of the waveform at the center of the screen and decrease frequency span
to increase the display resolution. As frequency span is decreased, the
number of points shown is reduced, and the display is magnified.
While the FFT spectrum is displayed, use the [Math] and [Cursors] keys to
switch between measurement functions and frequency domain controls in
FFT Menu.
FFT Resolution
NOTE
The FFT resolution is the quotient of the sampling rate and the number of FFT points (fS/N).
With a fixed number of FFT points (up to 65,536), the lower the sampling rate, the better the
resolution.
Decreasing the effective sampling rate by selecting a greater time/div

setting will increase the low frequency resolution of the FFT display and
also increase the chance that an alias will be displayed. The resolution of
the FFT is the effective sample rate divided by the number of points in
the FFT. The actual resolution of the display will not be this fine as the
shape of the window will be the actual limiting factor in the FFTs ability
to resolve two closely space frequencies. A good way to test the ability of
the FFT to resolve two closely spaced frequencies is to examine the
sidebands of an amplitude modulated sine wave.
For the best vertical accuracy on peak measurements:
• Make sure the probe attenuation is set correctly. The probe attenuation
is set from the Channel Menu if the operand is a channel.
• Set the source sensitivity so that the input signal is near full screen,
but not clipped.
• Use the Flat Top window.
• Set the FFT sensitivity to a sensitive range, such as 2 dB/division.
For best frequency accuracy on peaks:

4 Math Waveforms
• Use the Hanning window.

• Use Cursors to place an X cursor on the frequency of interest.
• Adjust frequency span for better cursor placement.
• Return to the Cursors Menu to fine tune the X cursor.
For more information on the use of FFTs please refer to Agilent
Application Note 243, The Fundamentals of Signal Analysis at
"http://cp.literature.agilent.com/litweb/pdf/5952- 8898E.pdf". Additional
information can be obtained from Chapter 4 of the book Spectrum and
Network Measurements by Robert A. Witte.
FFT Units
0 dBV is the amplitude of a 1 Vrms sinusoid. When the FFT source is
channel 1 or channel 2 (or channel 3 or 4 on 4- channel models), FFT
units will be displayed in dBV when channel units is set to Volts and
channel impedance is set to 1 MΩ.
FFT units will be displayed in dBm when channel units is set to Volts and
channel impedance is set to 50Ω.
FFT units will be displayed as dB for all other FFT sources or when a
source channel's units has been set to Amps.
FFT DC Value
The FFT computation produces a DC value that is incorrect. It does not
take the offset at center screen into account. The DC value is not
corrected in order to accurately represent frequency components near DC.
FFT Aliasing
When using FFTs, it is important to be aware of frequency aliasing. This
requires that the operator have some knowledge as to what the frequency
domain should contain, and also consider the sampling rate, frequency
span, and oscilloscope vertical bandwidth when making FFT
measurements. The FFT resolution (the quotient of the sampling rate and
the number of FFT points) is displayed directly above the softkeys when
the FFT Menu is displayed.

Math Waveforms 4
Nyquist Frequency and Aliasing in the Frequency Domain

NOTE
The Nyquist frequency is the highest frequency that any real-time digitizing oscilloscope
can acquire without aliasing. This frequency is half of the sample rate. Frequencies above
the Nyquist frequency will be under sampled, which causes aliasing. The Nyquist
frequency is also called the folding frequency because aliased frequency components fold
back from that frequency when viewing the frequency domain.
Aliasing happens when there are frequency components in the signal

higher than half the sample rate. Because the FFT spectrum is limited by
this frequency, any higher components are displayed at a lower (aliased)
frequency.
The following figure illustrates aliasing. This is the spectrum of a 990 Hz
square wave, which has many harmonics. The sample rate is set to
100 kSa/s, and the oscilloscope displays the spectrum. The displayed
waveform shows the components of the input signal above the Nyquist
frequency to be mirrored (aliased) on the display and reflected off the
right edge.
Figure 7 Aliasing

4 Math Waveforms
Because the frequency span goes from ≈ 0 to the Nyquist frequency, the
best way to prevent aliasing is to make sure that the frequency span is
greater than the frequencies of significant energy present in the input
signal.
FFT Spectral Leakage

The FFT operation assumes that the time record repeats. Unless there is
an integral number of cycles of the sampled waveform in the record, a
discontinuity is created at the end of the record. This is referred to as
leakage. In order to minimize spectral leakage, windows that approach
zero smoothly at the beginning and end of the signal are employed as
filters to the FFT. The FFT Menu provides four windows: Hanning, Flat
Top, Rectangular, and Blackman- Harris. For more information on leakage,
see Agilent Application Note 243, The Fundamentals of Signal Analysis at
"http://cp.literature.agilent.com/litweb/pdf/5952- 8898E.pdf."
Units for Math Waveforms

Units for each input channel can be set to Volts or Amps using the Units
softkey in the channel's Probe Menu. Units for math function waveforms
are:
Math function Units
add or subtract V or A
multiply V2, A2, or W (Volt-Amp)
FFT dB* (decibels). See also "FFT Units" on
page 72.
* When the FFT source is channel 1, 2, 3 or 4, FFT units will be displayed in dBV when channel
units is set to Volts and channel impedance is set to 1 MΩ. FFT units will be displayed in dBm
when channel units is set to Volts and channel impedance is set to 50Ω. FFT units will be
displayed as dB for all other FFT sources or when a source channel's units has been set to Amps.
A scale unit of U (undefined) will be displayed for math functions when

two source channels are used and they are set to dissimilar units and the
combination of units cannot be resolved.

User's Guide
5
Reference Waveforms
To save a waveform to a reference waveform location 75
To display a reference waveform 76
To scale and position reference waveforms 77
To adjust reference waveform skew 77
To display reference waveform information 78
To save/recall reference waveform files to/from a USB storage
device 78
Analog channel or math waveforms can be saved to one of two reference

waveform locations in the oscilloscope. Then, a reference waveform can be
displayed and compared against other waveforms. One reference waveform
can be displayed at a time.
When the multiplexed knobs are assigned to reference wavefroms (this
happens when you press the [Ref] key and the LED to the left of it is lit),
you can use the knobs to scale and position reference waveforms. There is
also a skew adjustment for reference waveforms. Reference waveform
scale, offset, and skew information can optionally be included on the
oscilloscope display.
Analog channel, math, or reference waveforms can be saved to a reference
waveform file on a USB storage device. You can recall a reference
waveform file from a USB storage device into one of the reference
waveform locations.
To save a waveform to a reference waveform location

1 Press the [Ref] key to turn on reference waveforms.
75
2 In the Reference Waveform Menu, press the Ref softkey and turn the
Entry knob to select the desired reference waveform location.
3 Press the Source softkey and turn the Entry knob to select the source
waveform.
4 Press the Save to R1/R2 softkey to save the waveform to the reference
waveform location.
Reference waveforms are non-volatile — they remain after power cycling or performing a
NOTE default setup.
To clear a 1 Press the [Ref] key to turn on reference waveforms.

reference 2 In the Reference Waveform Menu, press the Ref softkey and turn the
waveform Entry knob to select the desired reference waveform location.
location
3 Press the Clear R1/R2 softkey to clear the reference waveform location.
Reference waveforms are also cleared by a Factory Default or Secure
Erase (see Chapter 16, “Save/Recall (Setups, Screens, Data),” starting on
page 205).
To display a reference waveform

2 In the Reference Waveform Menu, press the Ref softkey and turn the
Entry knob to select the desired reference waveform location.
3 Then, press the Ref softkey again to enable/disable the reference
waveform display.

Reference Waveforms 5
One reference waveform can be displayed at a time.

See Also • "To display reference waveform information" on page 78
To scale and position reference waveforms

[Ref] key are selected for the reference waveform.
If the arrow to the left of the [Ref] key is not illuminated, press the key.
2 Turn the upper multiplexed knob to adjust the reference waveform
scale.
3 Turn the lower multiplexed knob to adjust the reference waveform
position.
To adjust reference waveform skew

Once reference waveforms are displayed, you can adjust their skew.

1 Display the desired reference waveform (see "To display a reference

waveform" on page 76).
2 Press the Skew softkey and turn the Entry knob to adjust the reference
waveform skew.
To display reference waveform information

2 In the Reference Waveform Menu, press the Options softkey.
3 In the Reference Waveform Options Menu, press the Display Info softkey
to enable or disable reference waveform information on the oscilloscope
display.
4 Press the Transparent softkey to enable or disable transparent
information backgrounds.
This setting is also used for other oscilloscope information on the
display, like mask test statistics, etc.
To save/recall reference waveform files to/from a USB storage device

Analog channel, math, or reference waveforms can be saved to a reference
waveform file on a USB storage device. See "To save reference waveform
files to a USB storage device" on page 213.
You can recall a reference waveform file from a USB storage device into
one of the reference waveform locations. See "To recall reference waveform
files from a USB storage device" on page 216.

User's Guide
6
Digital Channels
To connect the digital probes to the device under test 79
Acquiring waveforms using the digital channels 83
To display digital channels using AutoScale 83
Interpreting the digital waveform display 84
To switch all digital channels on or off 86
To switch groups of channels on or off 86
To switch a single channel on or off 86
To change the displayed size of the digital channels 85
To reposition a digital channel 87
To change the logic threshold for digital channels 86
To display digital channels as a bus 88
Digital channel signal fidelity: Probe impedance and grounding 91
To replace digital probe leads 96
This chapter describes how to use the digital channels of a Mixed- Signal
Oscilloscope (MSO).
The digital channels are enabled on MSOX2000 X- Series models and
DSOX2000 X- Series models that have the DSOX2MSO upgrade license
installed.
To connect the digital probes to the device under test

1 If necessary, turn off the power supply to the device under test.
79
6 Digital Channels
Turning off power to the device under test would only prevent damage
that might occur if you accidentally short two lines together while
connecting probes. You can leave the oscilloscope powered on because
no voltage appears at the probes.
Off
2 Connect the digital probe cable to the DIGITAL Dn - D0 connector on

the front panel of the mixed- signal oscilloscope. The digital probe cable
is keyed so you can connect it only one way. You do not need to
power- off the oscilloscope.
Probe cable for digital channels

CAUTION
Use only the Agilent logic probe and accessory kit supplied with the mixed-signal
oscilloscope (see "Accessories Available" on page 260).
3 Connect the ground lead on each set of channels (each pod), using a
probe grabber. The ground lead improves signal fidelity to the
oscilloscope, ensuring accurate measurements.

Digital Channels 6
Channel
Pod Ground
Circuit
Ground
4 Connect a grabber to one of the probe leads. (Other probe leads are
omitted from the figure for clarity.)
Grabber
5 Connect the grabber to a node in the circuit you want to test.

6 Digital Channels
6 For high- speed signals, connect a ground lead to the probe lead,
connect a grabber to the ground lead, and attach the grabber to ground
in the device under test.
Signal
Ground
Grabber
7 Repeat these steps until you have connected all points of interest.
Signals
Ground

Digital Channels 6
Acquiring waveforms using the digital channels

When you press [Run/Stop] or [Single] to run the oscilloscope, the
oscilloscope examines the input voltage at each input probe. When the
trigger conditions are met the oscilloscope triggers and displays the
acquisition.
For digital channels, each time the oscilloscope takes a sample it compares
the input voltage to the logic threshold. If the voltage is above the
threshold, the oscilloscope stores a 1 in sample memory; otherwise, it
stores a 0.
To display digital channels using AutoScale

When signals are connected to the digital channels — be sure to connect
the ground leads — AutoScale quickly configures and displays the digital
channels.
• To configure the instrument quickly, press the [AutoScale] key.
Figure 8 Example: AutoScale of digital channels (MSO models only)

6 Digital Channels
Any digital channel with an active signal will be displayed. Any digital
channels without active signals will be turned off.
• To undo the effects of AutoScale, press the Undo AutoScale softkey before
pressing any other key.
This is useful if you have unintentionally pressed the [AutoScale] key or do
not like the settings AutoScale has selected. This will return the
oscilloscope to its previous settings. See also: "How AutoScale Works" on
page 27.
To set the instrument to the factory- default configuration, press the
[Default Setup] key.
Interpreting the digital waveform display

The following figure shows a typical display with digital channels.

Digital Channels 6
Delay Time/ Trigger Trigger

time div mode or type and
run status source
Threshold
level
Digital Activity
channel indicators
identifiers
Waveform Turn Turn Threshold

size individual groups of menu key
channels channels
on/off on/off
Activity indicator When any digital channels are turned on, an activity indicator is displayed
in the status line at the bottom of the display. A digital channel can be
always high ( ), always low ( ), or actively toggling logic states ( ). Any
channel that is turned off will be grayed out in the activity indicator.
To change the displayed size of the digital channels

1 Press the [Digital] key.
2 Press the size ( ) softkey to select how the digital channels are
displayed.

6 Digital Channels
The sizing control lets you spread out or compress the digital traces
vertically on the display for more convenient viewing.
To switch a single channel on or off

1 With the Digital Channel Menu displayed, rotate the Entry knob to
select the desired channel from the popup menu.
2 Push the Entry knob or press the softkey that is directly below the
popup menu to switch the selected channel on or off.
To switch all digital channels on or off

1 Press the [Digital] key to toggle the display of digital channels. The
Digital Channel Menu is displayed above the softkeys.
If you want to switch the digital channels off, and the Digital Channel
Menu is not already displayed, you must push the [Digital] key twice to
switch the digital channels off. The first push displays the Digital Channel
Menu, and the second push switches the channels off.
To switch groups of channels on or off

1 Press the [Digital] key on the front panel if the Digital Channel Menu is
not already displayed.
2 Press the Turn off (or Turn on) softkey for the D7 - D0 group.
Each time you press the softkey, the softkey's mode toggles between Turn on
and Turn off.
To change the logic threshold for digital channels

1 Press the [Digital] key so that the Digital Channel Menu is displayed.
2 Press the Thresholds softkey

Digital Channels 6
3 Press the D7 - D0 softkey, then select a logic family preset or select User
to define your own threshold.
Logic family Threshold Voltage

TTL +1.4 V
CMOS +2.5 V
ECL –1.3 V
User Variable from –8 V to +8 V
The threshold you set applies to all channels within the selected D7 - D0
group. Each of the two channel groups can be set to a different threshold
if desired.
Values greater than the set threshold are high (1) and values less than the
set threshold are low (0).
If the Thresholds softkey is set to User, press the User softkey for the
channel group, then turn the Entry knob to set the logic threshold. There
is one User softkey for each group of channels.
To reposition a digital channel

key are selected for digital channels.
If the arrow to the left of the [Digital] key is not illuminated, press the
key.
2 Use the multiplexed Select knob to select the channel.
The selected waveform is highlighted in red.
3 Use the multiplexed Position knob to move the selected channel
waveform.
If a channel waveform is repositioned over another channel waveform,
the indicator at the left edge of the trace will change from Dnn
designation (where nn is a one or two digit channel number) to D*. The
"*" indicates that two channels are overlaid.

6 Digital Channels
To display digital channels as a bus

Digital channels may be grouped and displayed as a bus, with each bus
value displayed at the bottom of the display in hex or binary. You can
create up to two buses. To configure and display each bus, press the
[Digital] key on the front panel. Then press the Bus softkey.
Next, select a bus. Rotate the Entry knob, then press the Entry knob or
the Bus1/Bus2 softkey to switch it on.
Use the Channel softkey and the Entry knob to select individual channels
to be included in the bus. You can rotate the Entry knob and push it or
push the softkey to select channels. You can also press the Select/Deselect
D7-D0 softkey to include or exclude groups of eight channels in each bus.
If the bus display is blank, completely white, or if the display includes "...",
you need to expand the horizontal scale to allow space for the data to be
shown, or use the cursors to display the values (see "Using cursors to read
bus values" on page 89).
The Base softkey lets you choose to display the bus values in hex or
binary.
The buses are shown at the bottom of the display.

Digital Channels 6
Bus values can be shown in hex or binary.

Using cursors to To read the digital bus value at any point using the cursors:
read bus values 1 Turn on Cursors (by pressing the [Cursors] key on the front panel)
2 Press the cursor Mode softkey and change the mode to Hex or Binary.
3 Press the Source softkey and select Bus1 or Bus2.
4 Use the Entry knob and the X1 and X2 softkeys to position the cursors
where you want to read the bus values.

6 Digital Channels
X1 cursor
X2 cursor
Bus values
Set cursors Select Bus1 Bus values

mode to or Bus2 source at cursors
Binary or Hex shown here
When you press the [Digital] key to display the Digital Channel Menu, the
digital activity indicator is shown where the cursor values were and the
bus values at the cursors are displayed in the graticule.
Bus values are The bus values are also displayed when using the Pattern trigger function.
displayed when Press the [Pattern] key on the front panel to display the Pattern Trigger
using Pattern Menu and the bus values will be displayed on the right, above the
trigger softkeys.
The dollar sign ($) will be displayed in the bus value when the bus value
cannot be displayed as a hex value. This occurs when one or more "don't
cares" (X) are combined with low (0) and high (1) logic levels in the
pattern specification, or when a transition indicator — rising edge ( ) or
falling edge ( ) — are included in the pattern specification. A byte that
consists of all don't cares (X) will be displayed in the bus as a don't care
(X).

Digital Channels 6
Trigger Bus values Analog Digital

pattern displayed channel channel
definition values values
at cursor at cursor
See "Pattern Trigger" on page 116 for more information on Pattern

triggering.
Digital channel signal fidelity: Probe impedance and grounding

When using the mixed- signal oscilloscope you may encounter problems
that are related to probing. These problems fall into two categories: probe
loading and probe grounding. Probe loading problems generally affect the
device under test, while probe grounding problems affect the accuracy of
the data to the measurement instrument. The design of the probes
minimizes the first problem, while the second is easily addressed by good
probing practices.

6 Digital Channels
Input Impedance
The logic probes are passive probes, which offer high input impedance and
high bandwidths. They usually provide some attenuation of the signal to
the oscilloscope, typically 20 dB.
Passive probe input impedance is generally specified in terms of a parallel
capacitance and resistance. The resistance is the sum of the tip resistor
value and the input resistance of the test instrument (see the following
figure). The capacitance is the series combination of the tip compensating
capacitor and the cable, plus instrument capacitance in parallel with the
stray tip capacitance to ground. While this results in an input impedance
specification that is an accurate model for DC and low frequencies, the
high- frequency model of the probe input is more useful (see the following
figure). This high- frequency model takes into account pure tip capacitance
to ground as well as series tip resistance, and the cable's characteristic
impedance (Zo).
Figure 9 DC and Low-Frequency Probe Equivalent Circuit

Digital Channels 6
Figure 10 High-Frequency Probe Equivalent Circuit
The impedance plots for the two models are shown in these figures. By
comparing the two plots, you can see that both the series tip resistor and
the cable's characteristic impedance extend the input impedance
significantly. The stray tip capacitance, which is generally small (1 pF),
sets the final break point on the impedance chart.

6 Digital Channels
100 k
10 k High
Frequency
Model
Impedance
1k
Typical
100 Model
10
1
10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz
Frequency
Figure 11 Impedance versus Frequency for Both Probe Circuit Models
The logic probes are represented by the high- frequency circuit model
shown above. They are designed to provide as much series tip resistance
as possible. Stray tip capacitance to ground is minimized by the proper
mechanical design of the probe tip assembly. This provides the maximum
input impedance at high frequencies.
Probe Grounding
A probe ground is the low- impedance path for current to return to the
source from the probe. Increased length in this path will, at high
frequencies, create large common mode voltages at the probe input. The
voltage generated behaves as if this path were an inductor according to
the equation:
di
V = L dt

Digital Channels 6
Increasing the ground inductance (L), increasing the current (di) or

decreasing the transition time (dt), will all result in increasing the voltage
(V). When this voltage exceeds the threshold voltage defined in the
oscilloscope, a false data measurement will occur.
Sharing one probe ground with many probes forces all the current that
flows into each probe to return through the same common ground
inductance of the probe whose ground return is used. The result is
increased current (di) in the above equation, and, depending on the
transition time (dt), the common mode voltage may increase to a level that
causes false data generation.
Probe 1 Z in
i1
L (GND)
Probe Vn (Common Mode)

Ground i1+iÊ 2+iÊ n
i2 +iÊ n
Probe 2 Z in
in
Probe N Z in
Figure 12 Common Mode Input Voltage Model
In addition to the common mode voltage,longer ground returns also

degrade the pulse fidelity of the probe system. Rise time is increased, and
ringing, due to the undamped LC circuit at the input of the probe, is also
increased. Because the digital channels display reconstructed waveforms,
they do not show ringing and perturbations. You will not find ground
problems through examination of the waveform display. In fact, it is likely

6 Digital Channels
you will discover the problem through random glitches or inconsistent

data measurements. Use the analog channels to view ringing and
perturbations.
Best Probing Practices

Because of the variables L, di, and dt, you may be unsure how much
margin is available in your measurement setup. The following are
guidelines for good probing practices:
• The ground lead from each digital channel group (D15–D8 and D7–D0)
should be attached to the ground of the device under test if any
channel within the group is being used for data capture.
• When capturing data in a noisy environment, every third digital channel
probe's ground should be used in addition to the channel group's
ground.
• High- speed timing measurements (rise time < 3 ns) should make use of
each digital channel probe's own ground.
When designing a high- speed digital system, you should consider designing
dedicated test ports that interface directly to the instrument's probe
system. This will ease measurement setup and ensure a repeatable method
for obtaining test data. The 01650- 61607 16- channel logic probe cable and
the 01650- 63203 termination adapter are designed to make it easy to
connect to industry- standard, 20- pin board connectors. The cable is a 2 m
logic analyzer probe cable, and the termination adapter provides the
proper RC networks in a very convenient package. These parts, as well as
the 1251- 8106 20- pin, low- profile, straight board connector, can be
ordered from Agilent Technologies.
To replace digital probe leads

If you need to remove a probe lead from the cable, insert a paper clip or
other small pointed object into the side of the cable assembly, and push to
release the latch while pulling out the probe lead.

Digital Channels 6
Table 3 Digital Probe Replacement Parts
Part Number Description
N6459-60001 Digital probe kit, contains: N6459-61601 8-channel cable,

01650-82103 2-inch probe grounds (qty 3), and 5090-4832
grabbers (qty 10)
N6459-61601 8-channel cable with 8 probe leads and 1 pod ground lead (qty 1)
5959-9333 Replacement probe leads (qty 5), also contains 01650-94309
probe labels
5959-9334 Replacement 2-inch probe grounds (qty 5)
5959-9335 Replacement pod ground leads (qty 5)

5090-4833 Grabbers (qty 20)
01650-94309 Package of probe labels
For other replacement parts, consult the InfiniiVision 2000/3000 X- Series

Oscilloscopes Service Guide.

6 Digital Channels

User's Guide
7
Display Settings
To adjust waveform intensity 99
To set or clear persistence 101
To clear the display 102
To select the grid type 102
To adjust the grid intensity 103
To freeze the display 103
To adjust waveform intensity

You can adjust the intensity of displayed waveforms to account for various
signal characteristics, such as fast time/div settings and low trigger rates.
Increasing the intensity lets you see the maximum amount of noise and
infrequently occurring events.
Reducing the intensity can expose more detail in complex signals as
shown in the following figures.
1 Press the [Intensity] key to illuminate it.
This key is located just below the Entry knob.
2 Turn the Entry knob to adjust the waveform instensity.
Waveform intensity adjustment affects analog channel waveforms only (not
math waveforms, referencewaveforms, digital waveforms, etc.).
99
7 Display Settings
Figure 13 Amplitude Modulation Shown at 100% Intensity
Figure 14 Amplitude Modulation Shown at 40% Intensity

Display Settings 7
To set or clear persistence

With persistence, the oscilloscope updates the display with new
acquisitions, but does not immediately erase the results of previous
acquisitions. All previous acquisitions are displayed with reduced
intensity. New acquisitions are shown in their normal color with normal
intensity.
Waveform persistence is kept only for the current display area; you cannot
pan and zoom the persistence display.
To use persistence:
1 Press the [Display] key.
2 Press Persistence; then, turn the Entry knob to select between:

• Off — turns off persistence.
When persistence is off, you can press the Capture Waveforms softkey
to perform a single- shot infinite persistence. A single acquisition's
data is displayed with reduced intensity, and it remains on the
display until you clear persistence or clear the display.
• ∞ Persistence — (infinite presistence) Results of previous acquisitions
are never erased.
Use infinite persistence to measure noise and jitter, to see the
worst- case extremes of varying waveforms, to look for timing
violations, or to capture events that occur infrequently.
• Variable Persistence — Results of previous acquisitions are erased after
a certain amount of time.
Variable persistence gives you a view of acquired data that is similar
to analog oscilloscopes.
When variable persistence is selected, press the Time softkey and use
the Entry knob to specify the amount of time that previous
acquisitions are to be displayed.
The display will begin accumulating multiple acquisitions.

7 Display Settings
3 To erase the results of previous acquisitions from the display, press the
Clear Persistence softkey.
The oscilloscope will start to accumulate acquisitions again.
4 To return the oscilloscope to the normal display mode, turn off
persistence; then, press the Clear Persistence softkey.
Turning off persistence does not clear the display. The display is
cleared if you press the Clear Display softkey or if you press the
[AutoScale] key (which also turns off persistence).
For another method of seeing worst- case extremes of varying waveforms,
see "Glitch or Narrow Pulse Capture" on page 149.
To clear the display

1 Press [Display] > Clear Display.
You can also configure the [Quick Action] key to clear the display. See
"Configuring the [Quick Action] Key" on page 238.
To select the grid type

When the Video trigger type is selected (see "Video Trigger" on page 121),
and the vertical scaling of at least one displayed channel is 140 mV/div,
the Grid softkey lets you select from these grid types:
• Full — the normal oscilloscope grid.
• mV — shows vertical grids, labeled on the left, from - 0.3 V to 0.8 V.
• IRE — (Institute of Radio Engineers) shows vertical grids in IRE units,
labeled on the left, from - 40 to 100 IRE. The 0.35 V and 0.7 V levels
from the mV grid are also shown and labeled at the right. When the IRE
grid is selected, cursor values are also shown in IRE units. (Cursor
values via the remote interface are not in IRE units.)
The mV and IRE grid values are accurate (and match Y cursor values)
when the vertical scaling is 140 mV/division and the vertical offset is
245 mV.
To select the grid type:

Display Settings 7
1 Press [Display].
2 Press the Grid softkey; then, turn the Entry knob to select the grid
type.
To adjust the grid intensity

To adjust the display grid (graticule) intensity:
1 Press [Display].
2 Press the Intensity softkey; then, turn the Entry knob to change the
intensity of the displayed grid.
The intensity level is shown in the Intensity softkey and is adjustable from
0 to 100%.
Each major vertical division in the grid corresponds to the vertical
sensitivity shown in the status line at the top of the display.
Each major horizontal division in the grid corresponds to the time/div
shown in the status line at the top of the display.
To freeze the display

To freeze the display without stopping running acquisitions, you must
configure the [Quick Action] key. See "Configuring the [Quick Action]
Key" on page 238.
1 Once the [Quick Action] key has been configured, press it to freeze the
display.
2 To un- freeze the display, press [Quick Action] again.
Manual cursors can be used on the frozen display.
Many activities, such as adjusting the trigger level, adjusting vertical or
horizontal settings, or saving data will un- freeze the display.

7 Display Settings

User's Guide
8
Labels
To turn the label display on or off 105
To assign a predefined label to a channel 106
To define a new label 107
To load a list of labels from a text file you create 108
To reset the label library to the factory default 109
You can define labels and assign them to each analog input channel, or
you can turn labels off to increase the waveform display area. Labels can
also be applied to digital channels on MSO models.
To turn the label display on or off

1 Press the [Label] key on the front panel.
This turns on labels for the displayed analog and digital channels.
Labels are displayed at the left edge of the displayed traces.
The figure below shows an example of displayed labels.
105
8 Labels
2 To turn the labels off, press the [Label] key again.
To assign a predefined label to a channel

1 Press the [Label] key.
2 Press the Channel softkey, then turn the Entry knob or successively
press the Channel softkey to select a channel for label assignment.

Labels 8
The figure above shows the list of channels and their default labels. The
channel does not have to be turned on to have a label assigned to it.
3 Press the Library softkey, then turn the Entry knob or successively press
the Library softkey to select a predefined label from the library.
4 Press the Apply New Label softkey to assign the label to your selected
channel.
5 Repeat the above procedure for each predefined label you want to
assign to a channel.
To define a new label

1 Press the [Label] key.
2 Press the Channel softkey; then, turn the Entry knob or successively
press the softkey to select a channel for label assignment.
The channel does not have to be turned on to have a label assigned to
it. If the channel is turned on, its current label will be highlighted.
3 Press the Spell softkey; then, turn the Entry knob to select the first
character in the new label.

8 Labels
Turning the Entry knob selects a character to enter into the highlighted
position shown in the "New label =" line above the softkeys and in the
Spell softkey. Labels can be up to ten characters in length.
4 Press the Enter softkey to enter the selected character and to go to the
next character position.
5 You may position the highlight on any character in the label name by
successively pressing the Enter softkey.
6 To delete a character from the label, press the Enter softkey until the
letter you want to delete is highlighted, then press the Delete Character
softkey.
7 When you are done entering characters for the label, press the
Apply New Label softkey to assign the label to the selected channel.
When you define a new label, it is added to the nonvolatile label list.
Label Assignment When you assign a label ending in a digit, such as ADDR0 or DATA0, the
Auto-Increment oscilloscope automatically increments the digit and displays the modified
label in the "New label" field after you press the Apply New Label softkey.
Therefore, you only need to select a new channel and press the Apply New
Label softkey again to assign the label to the channel. Only the original
label is saved in the label list. This feature makes it easier to assign
successive labels to numbered control lines and data bus lines.
To load a list of labels from a text file you create

It may be convenient to create a list of labels using a text editor, then
load the label list into the oscilloscope. This lets you type on a keyboard
rather than edit the label list using the oscilloscope's controls.
You can create a list of up to 75 labels and load it into the oscilloscope.
Labels are added to the beginning of the list. If more than 75 labels are
loaded, only the first 75 are stored.
To load labels from a text file into the oscilloscope:
1 Use a text editor to create each label. Each label can be up to ten
characters in length. Separate each label with a line feed.
2 Name the file labellist.txt and save it on a USB mass storage device
such as a thumb drive.

Labels 8
3 Load the list into the oscilloscope using the File Explorer (press [Utility]
> File Explorer).
Label List Management

NOTE
When you press the Library softkey, you will see a list of the last 75 labels used. The list
does not save duplicate labels. Labels can end in any number of trailing digits. As long as
the base string is the same as an existing label in the library, the new label will not be put in
the library. For example, if label A0 is in the library and you make a new label called A12345,
the new label is not added to the library.
When you save a new user-defined label, the new label will replace the oldest label in the
list. Oldest is defined as the longest time since the label was last assigned to a channel.
Any time you assign any label to a channel, that label will move to the newest in the list.
Thus, after you use the label list for a while, your labels will predominate, making it easier
to customize the instrument display for your needs.
When you reset the label library list (see next topic), all of your custom labels will be
deleted, and the label list will be returned to its factory configuration.
To reset the label library to the factory default
Pressing the Default Library softkey will remove all user-defined labels from the library and
NOTE set the labels back to the factory default. Once deleted, these user-defined labels cannot be
recovered.
1 Press [Utility] > Options > Preferences.

2 Press the Default Library softkey.
This will delete all user- defined labels from the library and set the
labels in the library back to the factory default. However, this does not
default the labels currently assigned to the channels (those labels that
appear in the waveform area).
Defaulting labels without erasing the default library

NOTE
Pressing [Default Setup] sets all channel labels back to the default labels but does not
erase the list of user-defined labels in the library.

8 Labels

User's Guide
9
Triggers
Adjusting the Trigger Level 112
Forcing a Trigger 113
Edge Trigger 113
Pattern Trigger 116
Pulse Width Trigger 119
Video Trigger 121
A trigger setup tells the oscilloscope when to acquire and display data.
For example, you can set up to trigger on the rising edge of the analog
channel 1 input signal.
You can adjust the vertical level used for analog channel edge detection by
turning the Trigger Level knob.
In addition to the edge trigger type, you can also set up triggers on pulse
widths, patterns, and video signals.
You can use any input channel or the "External Trigger Input" on
page 138 BNC as the source for most trigger types.
Changes to the trigger setup are applied immediately. If the oscilloscope is
stopped when you change a trigger setup, the oscilloscope uses the new
specification when you press [Run/Stop] or [Single]. If the oscilloscope is
running when you change a trigger setup, it uses the new trigger
definition when it starts the next acquisition.
You can use the [Force Trigger] key to acquire and display data when
triggers are not occurring.
You can use the [Mode/Coupling] key to set options that affect all trigger
types (see Chapter 10, “Trigger Mode/Coupling,” starting on page 133).
111
9 Triggers
You can save trigger setups along with the oscilloscope setup (see
Chapter 16, “Save/Recall (Setups, Screens, Data),” starting on page 205).
Triggers - General A triggered waveform is one in which the oscilloscope begins tracing
Information (displaying) the waveform, from the left side of the display to the right,
each time a particular trigger condition is met. This provides stable
display of periodic signals such as sine waves and square waves, as well
as nonperiodic signals such as serial data streams.
The figure below shows the conceptual representation of acquisition
memory. You can think of the trigger event as dividing acquisition memory
into a pre- trigger and post- trigger buffer. The position of the trigger event
in acquisition memory is defined by the time reference point and the
delay (horizontal position) setting (see "To adjust the horizontal delay
(position)" on page 45).
Trigger Event
Pre-Trigger Buffer Post-Trigger Buffer
Acquisition Memory
Adjusting the Trigger Level

You can adjust the trigger level for a selected analog channel by turning
the Trigger Level knob.
You can push the Trigger Level knob to set the level to the waveform's
50% value. If AC coupling is used, pushing the Trigger Level knob sets the
trigger level to about 0 V.
The position of the trigger level for the analog channel is indicated by the
trigger level icon / (if the analog channel is on) at the far left side of the
display. The value of the analog channel trigger level is displayed in the
upper- right corner of the display.

Triggers 9
The trigger level for a selected digital channel is set using the threshold
menu in the Digital Channel Menu. Press the [Digital] key on the front
panel, then press the Thresholds softkey to set the threshold level (TTL,
CMOS, ECL, or user defined) for the selected digital channel group. The
threshold value is displayed in the upper- right corner of the display.
The line trigger level is not adjustable. This trigger is synchronized with
the power line supplied to the oscilloscope.
You can also change the trigger level of all channels by pressing [Analyze] > Features and
NOTE then selecting Trigger Levels.
Forcing a Trigger
The [Force Trigger] key causes a trigger (on anything) and displays the
acquisition.
This key is useful in the Normal trigger mode where acquisitions are made
only when the trigger condition is met. In this mode, if no triggers are
occurring (that is, the "Trig'd?" indicator is displayed), you can press [Force
Trigger] to force a trigger and see what the input signals look like.
In the Auto trigger mode, when the trigger condition is not met, triggers
are forced and the "Auto?" indicator is displayed.
Edge Trigger
The Edge trigger type identifies a trigger by looking for a specified edge
(slope) and voltage level on a waveform. You can define the trigger source
and slope in this menu. The slope can be set to rising edge or falling edge,
and can be set to alternating edges or either edge on all sources except
Line. The trigger type, source, and level are displayed in the upper- right
corner of the display.
1 On the front panel, in the Trigger section, press the [Trigger] key.
2 In the Trigger Menu, press the Trigger softkey, and use the Entry knob
to select Edge.
3 Select the trigger source:

9 Triggers
• Analog channel, 1 to the number of channels

• Digital channel (on mixed- signal oscilloscopes), D0 to the number of
digital channels minus one.
• External.
• Line.
• WaveGen (not available when the DC or Noise waveforms are
selected).
You can choose a channel that is turned off (not displayed) as the
source for the edge trigger.
The selected trigger source is indicated in the upper- right corner of the
display next to the slope symbol:
• 1 through 4 = analog channels.
• D0 through Dn = digital channels.
• E = External trigger input.
• L = Line trigger.
• W = Waveform generator.
4 Press the Slope softkey and select rising edge, falling edge, alternating
edges, or either edge. The selected slope is displayed in the upper- right
corner of the display.

Triggers 9
Alternating edge mode is useful when you want to trigger on both edges of a clock (for
NOTE example, DDR signals).
Either edge mode is useful when you want to trigger on any activity of a selected source.
All modes operate up to the bandwidth of the oscilloscope except Either edge mode, which
has a limitation. Either edge mode will trigger on Constant Wave signals up to 100 MHz, but
can trigger on isolated pulses down to 1/(2*oscilloscope's bandwidth).
Using AutoScale The easiest way to set up an Edge trigger on a waveform is to use
to Set Up Edge AutoScale. Simply press the [AutoScale] key and the oscilloscope will
Triggers attempt to trigger on the waveform using a simple Edge trigger type. See
"Use Auto Scale" on page 26.
MegaZoom Technology Simplifies Triggering

NOTE
With the built-in MegaZoom technology, you can simply AutoScale the waveforms, then
stop the oscilloscope to capture a waveform. You can then pan and zoom through the data
using the Horizontal and Vertical knobs to find a stable trigger point. AutoScale often
produces a triggered display.

9 Triggers
Pattern Trigger
The Pattern trigger identifies a trigger condition by looking for a specified
pattern. This pattern is a logical AND combination of the channels. Each
channel can have a value of 0 (low), 1 (high), or don't care (X). A rising
or falling edge can be specified for one channel included in the pattern.
You can also trigger on a hex bus value as described on "Hex Bus Pattern
Trigger" on page 118.
1 Press the [Trigger] key.
2 In the Trigger Menu, press the Trigger softkey; then, turn the Entry knob
to select Pattern.
3 For each analog or digital channel you want to include in the desired
pattern, press the Channel softkey to select the channel.
This is the channel source for the 0, 1, X, or edge condition. As you
press the Channel softkey (or rotate the Entry knob), the channel you
select is highlighted in the Pattern = line directly above the softkeys
and in the upper- right corner of the display next to "Pat".
Adjust the trigger level for the selected analog channel by turning the
Trigger Level knob. Press the [Digital] key and select Thresholds to set
the threshold level for digital channels. The value of the trigger level or
digital threshold is displayed in the upper- right corner of the display.
4 For each channel you select, press the Pattern softkey; then, turn the
Entry knob to set the condition for that channel in the pattern.

Triggers 9
• 0 sets the pattern to zero (low) on the selected channel. A low is a

voltage level that is less than the channel's trigger level or threshold
level.
• 1 sets the pattern to 1 (high) on the selected channel. A high is a
voltage level that is greater than the channel's trigger level or
threshold level.
• X sets the pattern to don't care on the selected channel. Any channel
set to don't care is ignored and is not used as part of the pattern.
However, if all channels in the pattern are set to don't care, the
oscilloscope will not trigger.
• The rising edge ( ) or falling edge ( ) softkey sets the pattern to an
edge on the selected channel. Only one rising or falling edge can be
specified in the pattern. When an edge is specified, the oscilloscope
will trigger at the edge specified if the pattern set for the other
channels is true.
If no edge is specified, the oscilloscope will trigger on the last edge
that makes the pattern true.

9 Triggers
Specifying an Edge in a Pattern

NOTE
You are allowed to specify only one rising or falling edge term in the pattern. If you define an
edge term, then select a different channel in the pattern and define another edge term, the
previous edge definition is changed to a don't care.
Hex Bus Pattern Trigger

You can specify a bus value on which to trigger. To do this, first define
the bus. See "To display digital channels as a bus" on page 88 for details.
You can trigger on a bus value whether you are displaying the bus or not.
To trigger on a bus value:
1 Press the [Pattern] key on the front panel.
2 Press the Channel softkey and rotate the Entry knob to select Bus1 or
Bus2.
3 Press the Digit softkey and rotate the Entry knob to select a digit of the
selected bus.
4 Press the Hex softkey and rotate the Entry knob to select a value for
the digit.
If a digit is made up of less than four bits, then the value of the digit will be limited to the
NOTE value that can be created by the selected bits.
5 You can use the Set all Digits softkey to set all digits to a particular
value.
When a hex bus digit contains one or more don't care (X) bits and one or
more bit with a value or 0 or 1, the "$" sign will be displayed for the digit.
For information regarding digital bus display when Pattern triggering see
"Bus values are displayed when using Pattern trigger" on page 90.

Triggers 9
Pulse Width Trigger

Pulse Width (glitch) triggering sets the oscilloscope to trigger on a positive
or negative pulse of a specified width. If you want to trigger on a specific
timeout value, use Pattern trigger in the Trigger Menu (see "Pattern
Trigger" on page 116).
to select Pulse Width.
3 Press the Source softkey; then, rotate the Entry knob to select a channel
source for the trigger.
The channel you select is shown in the upper- right corner of the
display next to the polarity symbol.
The source can be any analog or digital channel available on your
oscilloscope.
4 Adjust the trigger level:
• For analog channels, turn the Trigger Level knob.

9 Triggers
• For digital channels, press the [Digital] key and select Thresholds to set
the threshold level.
The value of the trigger level or digital threshold is displayed in the
upper- right corner of the display.
5 Press the pulse polarity softkey to select positive ( ) or negative ( )

polarity for the pulse width you want to capture.
The selected pulse polarity is displayed in the upper- right corner of the
display. A positive pulse is higher than the current trigger level or
threshold and a negative pulse is lower than the current trigger level or
threshold.
When triggering on a positive pulse, the trigger will occur on the high
to low transition of the pulse if the qualifying condition is true. When
triggering on a negative pulse, the trigger will occur on the low to high
transition of the pulse if the qualifying condition is true.
6 Press the qualifier softkey (< > ><) to select the time qualifier.
The Qualifier softkey can set the oscilloscope to trigger on a pulse
width that is:
• Less than a time value (<).
For example, for a positive pulse, if you set t<10 ns:
10 ns 10 ns Trigger
• Greater than a time value (>).

For example, for a positive pulse, if you set t>10 ns:
10 ns 10 ns Trigger
• Within a range of time values (><).

For example, for a positive pulse, if you set t>10 ns and t<15 ns:

Triggers 9
10 ns 15 ns 12 ns Trigger
7 Select the qualifier time set softkey (< or >), then rotate the Entry
knob to set the pulse width qualifier time.
The qualifiers can be set as follows:
• 2 ns to 10 s for > or < qualifier (5 ns to 10 s for 350 MHz
bandwidth models).
• 10 ns to 10 s for >< qualifier, with minimum difference of 5 ns
between upper and lower settings.
Pulse width • When the less than (<) qualifier is selected, the Entry knob sets the
trigger < qualifier oscilloscope to trigger on a pulse width less than the time value
time set softkey displayed on the softkey.
• When the time range (><) qualifier is selected, the Entry knob sets the
upper time range value.
Pulse width • When the greater than (>) qualifier is selected, the Entry knob sets the
trigger > qualifier oscilloscope to trigger on a pulse width greater than the time value
time set softkey displayed on the softkey.
• When the time range (><) qualifier is selected, the Entry knob sets the
lower time range value.
Video Trigger
Video triggering can be used to capture the complicated waveforms of
most standard analog video signals. The trigger circuitry detects the
vertical and horizontal interval of the waveform and produces triggers
based on the video trigger settings you have selected.
The oscilloscope's MegaZoom IV technology gives you bright, easily viewed
displays of any part of the video waveform. Analysis of video waveforms is
simplified by the oscilloscope's ability to trigger on any selected line of the
video signal.

9 Triggers
It is important, when using a 10:1 passive probe, that the probe is correctly compensated.
NOTE The oscilloscope is sensitive to this and will not trigger if the probe is not properly
compensated, especially for progressive formats.

to select Video.
3 Press the Source softkey and select any analog channel as the video
trigger source.
The selected trigger source is displayed in the upper- right corner of the
display. Turning the Trigger Level knob does not change the trigger level
because the trigger level is automatically set to the sync pulse. Trigger
coupling is automatically set to TV in the Trigger Mode and Coupling
Menu.

Triggers 9
Provide Correct Matching

NOTE
Many video signals are produced from 75 Ω sources. To provide correct matching to these
sources, a 75 Ω terminator (such as an Agilent 11094B) should be connected to the
oscilloscope input.
4 Press the sync polarity softkey to set the Video trigger to either positive
( ) or negative ( ) sync polarity.
5 Press the Settings softkey.
6 In the Video Trigger Menu, press the Standard softkey to set the video
standard.
The oscilloscope supports triggering on the following television (TV) and
video standards.
Standard Type Sync Pulse

NTSC Interlaced Bi-level
PAL Interlaced Bi-level

PAL-M Interlaced Bi-level
SECAM Interlaced Bi-level
7 Press the Auto Setup softkey to automatically set up the oscilloscope for
the selected Source and Standard:
• Source channel vertical scaling is set to 140 mV/div.
• Source channel offset is set to 245 mV.
• Source channel is turned on.
• Trigger type is set to Video.
• Video trigger mode is set to All Lines.
• Display Grid type is set to IRE (when Standard is NTSC) or mV (see "To
select the grid type" on page 102).

9 Triggers
• Horizontal time/division is set to 10 µs/div for NTSC/PAL/SECAM

standards.
• Horizontal delay is set so that trigger is at first horizontal division
from the left.
You can also press [Analyze]> Features and then select Video to quickly
access the video triggering automatic set up and display options.
8 Press the Mode softkey to select the portion of the video signal that you
would like to trigger on.
The Video trigger modes available are:
• Field1 and Field2 — Trigger on the rising edge of the first serration
pulse of field 1 or field 2 (interlaced standards only).
• All Fields — Trigger on the rising edge of the first pulse in the vertical
sync interval.
• All Lines — Trigger on all horizontal sync pulses.
• Line: Field1 and Line:Field2 — Trigger on the selected line # in field 1 or
field 2 (interlaced standards only).
• Line: Alternate — Alternately trigger on the selected line # in field 1
and field 2 (NTSC, PAL, PAL- M, and SECAM only).
9 If you select a line # mode, press the Line # softkey, then rotate the
Entry knob to select the line number on which you want to trigger.
The following table lists the line (or count) numbers per field for each
video standard.
Video standard Field 1 Field 2 Alt Field

NTSC 1 to 263 1 to 262 1 to 262
PAL 1 to 313 314 to 625 1 to 312
PAL-M 1 to 263 264 to 525 1 to 262
SECAM 1 to 313 314 to 625 1 to 312
Video Triggering The following are exercises to familiarize you with video triggering. These
Examples exercises use the NTSC video standard.
• "To trigger on a specific line of video" on page 125

Triggers 9
• "To trigger on all sync pulses" on page 126

• "To trigger on a specific field of the video signal" on page 127
• "To trigger on all fields of the video signal" on page 128
• "To trigger on odd or even fields" on page 129
To trigger on a specific line of video

Video triggering requires greater than 1/2 division of sync amplitude with
any analog channel as the trigger source. Turning the trigger Level knob in
Video trigger does not change the trigger level because the trigger level is
automatically set to the sync pulse tips.
One example of triggering on a specific line of video is looking at the
vertical interval test signals (VITS), which are typically in line 18. Another
example is closed captioning, which is typically in line 21.
to select Video.
3 Press the Settings softkey, then press the Standard softkey to select the
appropriate TV standard (NTSC).
4 Press the Mode softkey and select the TV field of the line you want to
trigger on. You can choose Line:Field1, Line:Field2, or Line:Alternate.
5 Press the Line # softkey and select the number of the line you want to
examine.
Alternate Triggering
NOTE
If Line:Alternate is selected, the oscilloscope will alternately trigger on the selected line
number in Field 1 and Field 2. This is a quick way to compare the Field 1 VITS and Field 2
VITS or to check for the correct insertion of the half line at the end of Field 1.

9 Triggers
Figure 15 Example: Triggering on Line 136
To trigger on all sync pulses

To quickly find maximum video levels, you could trigger on all sync
pulses. When All Lines is selected as the Video trigger mode, the
oscilloscope will trigger on all horizontal sync pulses.
to select Video.
appropriate TV standard.
4 Press the Mode softkey and select All Lines.

Triggers 9
Figure 16 Triggering on All Lines
To trigger on a specific field of the video signal

To examine the components of a video signal, trigger on either Field 1 or
Field 2 (available for interleaved standards). When a specific field is
selected, the oscilloscope triggers on the rising edge of the first serration
pulse in the vertical sync interval in the specified field (1 or 2).
to select Video.
4 Press the Mode softkey and select Field1 or Field2.

9 Triggers
Figure 17 Triggering on Field 1
To trigger on all fields of the video signal

To quickly and easily view transitions between fields, or to find the
amplitude differences between the fields, use the All Fields trigger mode.
to select Video.
4 Press the Mode softkey and select All Fields.

Triggers 9
Figure 18 Triggering on All Fields
To trigger on odd or even fields

To check the envelope of your video signals, or to measure worst case
distortion, trigger on the odd or even fields. When Field 1 is selected, the
oscilloscope triggers on color fields 1 or 3. When Field 2 is selected, the
oscilloscope triggers on color fields 2 or 4.
to select Video.
4 Press the Mode softkey and select Field1 or Field2.
The trigger circuits look for the position of the start of Vertical Sync to
determine the field. But this definition of field does not take into
consideration the phase of the reference subcarrier. When Field 1 is
selected, the trigger system will find any field where the vertical sync

9 Triggers
starts on Line 4. In the case of NTSC video, the oscilloscope will trigger
on color field 1 alternating with color field 3 (see the following figure).
This setup can be used to measure the envelope of the reference burst.
Figure 19 Triggering on Color Field 1 Alternating with Color Field 3
If a more detailed analysis is required, then only one color field should be
selected to be the trigger. You can do this by using the Field Holdoff softkey
in the Video Trigger Menu. Press the Field Holdoff softkey and use the Entry
knob to adjust the holdoff in half- field increments until the oscilloscope
triggers on only one phase of the color burst.
A quick way to synchronize to the other phase is to briefly disconnect the
signal and then reconnect it. Repeat until the correct phase is displayed.
When holdoff is adjusted using the Field Holdoff softkey and the Entry knob,
the corresponding holdoff time will be displayed in the Trigger Mode and
Coupling Menu.

Triggers 9
Table 4 Half-field holdoff time
Standard Time
NTSC 8.35 ms
PAL 10 ms
PAL-M 10 ms
SECAM 10 ms
Figure 20 Using Field Holdoff to Synchronize to Color Field 1 or 3 (Field 1 mode)

9 Triggers

User's Guide
10
Trigger Mode/Coupling
To select the Auto or Normal trigger mode 134
To select the trigger coupling 136
To enable or disable trigger noise rejection 137
To enable or disable trigger HF Reject 137
To set the trigger holdoff 138
External Trigger Input 138
To access the Trigger Mode and Coupling Menu:

• In the Trigger section of the front panel, press the [Mode/Coupling] key.
Noisy Signals If the signal you are probing is noisy, you can set up the oscilloscope to
reduce the noise in the trigger path and on the displayed waveform. First,
stabilize the displayed waveform by removing the noise from the trigger
path. Second, reduce the noise on the displayed waveform.
1 Connect a signal to the oscilloscope and obtain a stable display.
2 Remove the noise from the trigger path by turning on high- frequency
rejection ("To enable or disable trigger HF Reject" on page 137),
low- frequency rejection ("To select the trigger coupling" on page 136),
or "To enable or disable trigger noise rejection" on page 137.
3 Use "Averaging Acquisition Mode" on page 151 to reduce noise on the
displayed waveform.
133
To select the Auto or Normal trigger mode

When the oscilloscope is running, the trigger mode tells the oscilloscope
what to do when triggers are not occurring.
In the Auto trigger mode (the default setting), if the specified trigger
conditions are not found, triggers are forced and acquisitions are made so
that signal activity is displayed on the oscilloscope.
In the Normal trigger mode, triggers and acquisitions only occur when the
specified trigger conditions are found.
To select the trigger mode:
1 Press the [Mode/Coupling] key.
2 In the Trigger Mode and Coupling Menu, press the Mode softkey; then
select either Auto or Normal.
See the following "When to Use Auto Trigger Mode" on page 135 and
"When to Use Normal Trigger Mode" on page 135 descriptions.
You can also configure the [Quick Action] key to toggle between the Auto
and Normal trigger modes. See "Configuring the [Quick Action] Key" on
page 238.
Triggering and After the oscilloscope starts running (after pressing [Run] or [Single] or
the Pre- and changing the trigger condition), the oscilloscope first fills the pre- trigger
Post-Trigger buffer. Then, after the pre- trigger buffer is filled, the oscilloscope starts
Buffers searching for a trigger, and sampled data continues to flow data through
the pre- trigger buffer in a first- in first- out (FIFO) manner.
When a trigger is found, the pre- trigger buffer contains the events that
occurred just before the trigger. Then, the oscilloscope fills the post- trigger
buffer and displays the acquisition memory. If the acquisition was
initiated by [Run/Stop], the process repeats. If the acquisition was initiated
by pressing [Single], the acquisition stops (and you can Pan and Zoom the
waveform).
In either Auto or Normal trigger mode, a trigger may be missed if the
event occurs while the pre- trigger buffer is being filled. This may be more
likely, for example, when the horizontal scale knob is set to a slow
time/div setting, such as 500 ms/div.

Trigger Mode/Coupling 10
Trigger Indicator The trigger indicator at the top right of the display shows whether triggers
are occurring.
In the Auto trigger mode, the trigger indicator can show:
• Auto? (flashing) — the trigger condition is not found (after the
pre- trigger buffer has filled), and forced triggers and acquisitions are
occurring.
• Auto (not flashing) — the trigger condition is found (or the pre- trigger
buffer is being filled).
In the Normal trigger mode, the trigger indicator can show:
• Trig'd? (flashing) — the trigger condition is not found (after the
pre- trigger buffer has filled), and no acquisitions are occurring.
• Trig'd (not flashing) — trigger condition is found (or pre- trigger buffer is
being filled).
When the oscilloscope is not running, the trigger indicator area shows
Stop.
When to Use Auto The Auto trigger mode is appropriate when:
Trigger Mode • Checking DC signals or signals with unknown levels or activity.
• When trigger conditions occur often enough that forced triggers are
unnecessary.
When to Use The Normal trigger mode is appropriate when:
Normal Trigger • You only want to acquire specific events specified by the trigger
Mode settings.
• Triggering on an infrequent signal from a serial bus (for example, I2C,
SPI, CAN, LIN, etc.) or another signal that arrives in bursts. The Normal
trigger mode lets you stabilize the display by preventing the oscilloscope
from autotriggering.
• Making single- shot acquisitions with the [Single] key.
Often with single- shot acquisitions, you must initiate some action in the
device under test, and you don't want the oscilloscope to auto- trigger
before that happens. Before initiating the action in the circuit, wait for
the trigger condition indicator Trig'd? to flash (this tells you the
pre- trigger buffer is filled).
See Also • "Forcing a Trigger" on page 113
• "To set the trigger holdoff" on page 138

• "To position the time reference (left, center, right)" on page 52
To select the trigger coupling

2 In the Trigger Mode and Coupling Menu, press the Coupling softkey;
then, turn the Entry knob to select:
• DC coupling — allows DC and AC signals into the trigger path.
• AC coupling — places a 10 Hz high- pass filter in the trigger path
removing any DC offset voltage from the trigger waveform.
The high- pass filter in the External Trigger input path is 50 Hz for
all models.
Use AC coupling to get a stable edge trigger when your waveform has
a large DC offset.
• LF (low frequency) Reject coupling — adds a high- pass filter with the
3- dB point at 50 kHz in series with the trigger waveform.
0 dB
3 dB down point
Pass
Band
DC 50 kHz
Low frequency reject removes any unwanted low frequency

components from a trigger waveform, such as power line frequencies,
etc., that can interfere with proper triggering.
Use LF Reject coupling to get a stable edge trigger when your
waveform has low frequency noise.
• TV coupling — is normally grayed- out, but is automatically selected
when TV trigger is enabled in the Trigger Menu.

Note that Trigger Coupling is independent of Channel Coupling (see "To

specify channel coupling" on page 57).
To enable or disable trigger noise rejection

Noise Rej adds additional hysteresis to the trigger circuitry. By increasing
the trigger hysteresis band, you reduce the possibility of triggering on
noise. However, this also decreases the trigger sensitivity so that a slightly
larger signal is required to trigger the oscilloscope.
2 In the Trigger Mode and Coupling Menu, press the Noise Rej softkey to
enable or disable.
To enable or disable trigger HF Reject

HF Reject adds a 50 kHz low- pass filter in the trigger path to remove high
frequency components from the trigger waveform.
0 dB
-3 dB Pass
Band
DC 50 kHz
You can use HF Reject to remove high- frequency noise, such as AM or FM

broadcast stations or noise from fast system clocks, from the trigger path.
2 In the Trigger Mode and Coupling Menu, press the HF Reject softkey to
enable or disable.

To set the trigger holdoff

Trigger holdoff sets the amount of time the oscilloscope waits after a
trigger before re- arming the trigger circuitry.
Use the holdoff to trigger on repetitive waveforms that have multiple edges
(or other events) between waveform repetitions. You can also use holdoff
to trigger on the first edge of a burst when you know the minimum time
between bursts.
For example, to get a stable trigger on the repetitive pulse burst shown
below, set the holdoff time to be >200 ns but <600 ns.
Holdoff Oscilloscope triggers here
200 ns 600 ns
To set the trigger holdoff:

2 In the Trigger Mode and Coupling Menu, press the Holdoff softkey; then,
turn the Entry knob to increase or decrease the trigger holdoff time.
Trigger Holdoff The correct holdoff setting is typically slightly less than one repetition of
Operating Hints the waveform. Set the holdoff to this time to generate a unique trigger
point for a repetitive waveform.
Changing the time base settings does not affect the trigger holdoff time.
With Agilent's MegaZoom technology, you can press [Stop], then pan and
zoom through the data to find where the waveform repeats. Measure this
time using cursors; then, set the holdoff.
External Trigger Input

The external trigger input can be used as a source in several of the trigger
types. The external trigger BNC input is on the rear panel and is labeled
EXT TRIG IN.

Maximum voltage at oscilloscope external trigger input

CAUTION
1 M ohm input: For steady-state sinusoidal waveforms derate at 20 dB/decade above
57 kHz to a minimum of 5 Vpk
With N2863A 10:1 probe: CAT I 600 V, CAT II 300 V (DC + peak AC)
With 10073C or 10074C 10:1 probe: CAT I 500 Vpk, CAT II 400 Vpk
The external trigger input impedance is 1M Ohm. This lets you use passive
probes for general- purpose measurements. The higher impedance
minimizes the loading effect of the oscilloscope on the device under test.
To set the EXT TRIG IN units and probe attenuation:
1 Press the [Mode/Coupling] key in the Trigger section of the front panel.
2 In the Trigger Mode and Coupling Menu, press the External softkey.
3 In the External Trigger Menu, press the Units softkey to select between:
• Volts — for a voltage probe.
• Amps — for a current probe.
Measurement results, channel sensitivity, and the trigger level will
reflect the measurement units you have selected.
4 Press the Probe softkey; then, turn the entry knob to specify the probe
attenuation.
The attenuation factor can be set from 0.1:1 to 1000:1 in a 1- 2- 5
sequence.
The probe attenuation factor must be set properly for measurements to
be made correctly.


User's Guide
11
Acquisition Control
Running, Stopping, and Making Single Acquisitions (Run Control) 141
Overview of Sampling 143
Selecting the Acquisition Mode 147
Acquiring to Segmented Memory 153
This chapter shows how to use the oscilloscope's acquisition and run
controls.
Running, Stopping, and Making Single Acquisitions (Run Control)

There are two front panel keys for starting and stopping the oscilloscope's
acquisition system: [Run/Stop] and [Single].
• When the [Run/Stop] key is green, the oscilloscope is running, that is,
acquiring data when trigger conditions are met.
To stop acquiring data, press [Run/Stop]. When stopped, the last
acquired waveform is displayed.
• When the [Run/Stop] key is red, data acquisition is stopped.
"Stop" is displayed next to the trigger type in the status line at the top
of the display.
To start acquiring data, press [Run/Stop].
• To capture and display a single acquisition (whether the oscilloscope is
running or stopped), press [Single].
The [Single] run control lets you view single- shot events without
subsequent waveform data overwriting the display. Use [Single] when
you want maximum memory depth for pan and zoom.
141
When you press [Single], the display is cleared, the trigger mode is
temporarily set to Normal (to keep the oscilloscope from autotriggering
immediately), the trigger circuitry is armed, the [Single] key is
illuminated, and the oscilloscope waits until a trigger condition occurs
before it displays a waveform.
When the oscilloscope triggers, the single acquisition is displayed and
the oscilloscope is stopped (the [Run/Stop] key is illuminated in red).
Press [Single] again to acquire another waveform.
If the oscilloscope doesn't trigger, you can press the [Force Trigger] key to
trigger on anything and make a single acquisition.
To display the results of multiple acquisitions, use persistence. See "To set
or clear persistence" on page 101.
Single vs. The maximum data record length is greater for a single acquisition than
Running and when the oscilloscope is running (or when the oscilloscope is stopped
Record Length after running):
• Single — Single acquisitions always use the maximum memory available
— at least twice as much memory as acquisitions captured when
running — and the oscilloscope stores at least twice as many samples.
At slower time/div settings, because there is more memory available for
a single acquisition, the acquisition has a higher effective sample rate.
• Running — When running (versus taking a single acquisition), the
memory is divided in half. This lets the acquisition system acquire one
record while processing the previous acquisition, dramatically improving
the number of waveforms per second processed by the oscilloscope.
When running, a high waveform update rate provides the best
representation of your input signal.
To acquire data with the longest possible record length, press the [Single]
key.
For more information on settings that affect record length, see "Length
Control" on page 211.

Acquisition Control 11
Overview of Sampling
To understand the oscilloscope's sampling and acquisition modes, it is
helpful to understand sampling theory, aliasing, oscilloscope bandwidth
and sample rate, oscilloscope rise time, oscilloscope bandwidth required,
and how memory depth affects sample rate.
Sampling Theory
The Nyquist sampling theorem states that for a limited bandwidth
(band- limited) signal with maximum frequency fMAX, the equally spaced
sampling frequency fS must be greater than twice the maximum frequency
fMAX, in order to have the signal be uniquely reconstructed without
aliasing.
fMAX = fS/2 = Nyquist frequency (fN) = folding frequency
Aliasing
Aliasing occurs when signals are under- sampled (fS < 2fMAX). Aliasing is
the signal distortion caused by low frequencies falsely reconstructed from
an insufficient number of sample points.
Figure 21 Aliasing

Oscilloscope Bandwidth and Sample Rate

An oscilloscope's bandwidth is typically described as the lowest frequency
at which input signal sine waves are attenuated by 3 dB (- 30% amplitude
error).
At the oscilloscope bandwidth, sampling theory says the required sample
rate is fS = 2fBW. However, the theory assumes there are no frequency
components above fMAX (fBW in this case) and it requires a system with
an ideal brick- wall frequency response.
%Y7
"(Y7
6iiZcjVi^dc
[C [H
;gZfjZcXn
Figure 22 Theoretical Brick-Wall Frequency Response
However, digital signals have frequency components above the fundamental

frequency (square waves are made up of sine waves at the fundamental
frequency and an infinite number of odd harmonics), and typically, for
1 Ghz bandwidths and below, oscilloscopes have a Gaussian frequency
response.

%Y7
"(Y7
6iiZcjVi^dc
6a^VhZY[gZfjZcXn
XdbedcZcih
[H$) [C [H
;gZfjZcXn
Limiting oscilloscope bandwidth (fBW) to 1/4 the sample rate (fS/4)

reduces frequency components above the Nyquist frequency (fN).
Figure 23 Sample Rate and Oscilloscope Bandwidth
So, in practice, an oscilloscope's sample rate should be four or more times

its bandwidth: fS = 4fBW. This way, there is less aliasing, and aliased
frequency components have a greater amount of attenuation.
See Also Evaluating Oscilloscope Sample Rates vs. Sampling Fidelity: How to
Make the Most Accurate Digital Measurements, Agilent Application Note
1587 ("http://cp.literature.agilent.com/litweb/pdf/5989- 5732EN.pdf")
Oscilloscope Rise Time

Closely related to an oscilloscope's bandwidth specification is its rise time
specification. Oscilloscopes with a Gaussian- type frequency response have
an approximate rise time of 0.35/fBW based on a 10% to 90% criterion.
An oscilloscope's rise time is not the fastest edge speed that the
oscilloscope can accurately measure. It is the fastest edge speed the
oscilloscope can possibly produce.

Oscilloscope Bandwidth Required

The oscilloscope bandwidth required to accurately measure a signal is
primarily determined by the signal's rise time, not the signal's frequency.
You can use these steps to calculate the oscilloscope bandwidth required:
1 Determine the fastest edge speeds.
You can usually obtain rise time information from published
specifications for devices used in your designs.
2 Compute the maximum "practical" frequency component.
From Dr. Howard W. Johnson's book, High- Speed Digital Design – A
Handbook of Black Magic, all fast edges have an infinite spectrum of
frequency components. However, there is an inflection (or "knee") in the
frequency spectrum of fast edges where frequency components higher
than fknee are insignificant in determining the shape of the signal.
fknee = 0.5 / signal rise time (based on 10% - 90% thresholds)
fknee = 0.4 / signal rise time (based on 20% - 80% thresholds)

3 Use a multiplication factor for the required accuracy to determine the
oscilloscope bandwidth required.
Required accuracy Oscilloscope bandwidth required
20% fBW = 1.0 x fknee
See Also Choosing an Oscilloscope with the Right Bandwidth for your
Application, Agilent Application Note 1588
("http://cp.literature.agilent.com/litweb/pdf/5989- 5733EN.pdf")

Memory Depth and Sample Rate

The number of points of oscilloscope memory is fixed, and there is a
maximum sample rate associated with oscilloscope's analog- to- digital
converter; however, the actual sample rate is determined by the time of
the acquisition (which is set according to the oscilloscope's horizontal
time/div scale).
sample rate = number of samples / time of acquisition
For example, when storing 50 µs of data in 50,000 points of memory, the
actual sample rate is 1 GSa/s.
Likewise, when storing 50 ms of data in 50,000 points of memory, the
actual sample rate is 1 MSa/s.
The actual sample rate is displayed in the right- side information area.
The oscilloscope achieves the actual sample rate by throwing away
(decimating) unneeded samples.
Selecting the Acquisition Mode

When selecting the oscilloscope acquisition mode, keep in mind that
samples are normally decimated at slower time/div settings.
At slower time/div settings, the effective sample rate drops (and the
effective sample period increases) because the acquisition time increases
and the oscilloscope's digitizer is sampling faster than is required to fill
memory.
For example, suppose an oscilloscope's digitizer has a sample period of
1 ns (maximum sample rate of 1 GSa/s) and a 1 M memory depth. At that
rate, memory is filled in 1 ms. If the acquisition time is 100 ms
(10 ms/div), only 1 of every 100 samples is needed to fill memory.
To select the acquisition mode:
1 Press the [Acquire] key on the front panel.
2 In the Acquire Menu, press the Acq Mode softkey; then, turn the Entry
knob to select the acquisition mode.
The InfiniiVision oscilloscopes have the following acquisition modes:

• Normal — at slower time/div settings, normal decimation occurs, and

there is no averaging. Use this mode for most waveforms. See
"Normal Acquisition Mode" on page 148.
• Peak Detect — at slower time/div settings, the maximum and minimum
samples in the effective sample period are stored. Use this mode for
displaying narrow pulses that occur infrequently. See "Peak Detect
Acquisition Mode" on page 148.
• Averaging — at all time/div settings, the specified number of triggers
are averaged together. Use this mode for reducing noise and
increasing resolution of periodic signals without bandwidth or rise
time degradation. See "Averaging Acquisition Mode" on page 151.
• High Resolution — at slower time/div settings, all samples in the
effective sample period are averaged and the average value is stored.
Use this mode for reducing random noise. See "High Resolution
Acquisition Mode" on page 153.
Normal Acquisition Mode

In Normal mode at slower time/div settings, extra samples are decimated
(in other words, some are thrown away). This mode yields the best display
for most waveforms.
Peak Detect Acquisition Mode

In Peak Detect mode, at slower time/div settings when decimation would
normally occur, minimum and maximum value samples are kept in order
to capture infrequent and narrow events (at the expense of exaggerating
any noise). This mode displays all pulses that are at least as wide as the
sample period.
For InfiniiVision 2000 X- Series oscilloscopes, which have a maximum
sample rate of 2 GSa/s, a sample is taken every 500 ps (sample period).
See Also • "Glitch or Narrow Pulse Capture" on page 149
• "Using Peak Detect Mode to Find a Glitch" on page 150

Glitch or Narrow Pulse Capture

A glitch is a rapid change in the waveform that is usually narrow as
compared to the waveform. Peak detect mode can be used to more easily
view glitches or narrow pulses. In peak detect mode, narrow glitches and
sharp edges are displayed more brightly than when in Normal acquire
mode, making them easier to see.
To characterize the glitch, use the cursors or the automatic measurement
capabilities of the oscilloscope.
Figure 24 Sine With Glitch, Normal Mode

Figure 25 Sine With Glitch, Peak Detect Mode
Using Peak Detect Mode to Find a Glitch

2 To find the glitch, press the [Acquire] key; then, press the Acq Mode
softkey until Peak Detect is selected.
3 Press the [Display] key then press the ∞ Persistence (infinite persistence)
softkey.
Infinite persistence updates the display with new acquisitions but does
not erase previous acquisitions. New sample points are shown at normal
intensity while previous acquisitions are displayed at reduced intensity.
Waveform persistence is not kept beyond the display area boundary.
Press the Clear Display softkey to erase previously acquired points. The
display will accumulate points until ∞ Persistence is turned off.
4 Characterize the glitch with Zoom mode:
a Press the zoom key (or press the [Horiz] key and then the Zoom
softkey).
b To obtain a better resolution of the glitch, expand the time base.

Use the horizontal position knob ( ) to pan through the waveform to set
the expanded portion of the normal window around the glitch.
Averaging Acquisition Mode

The Averaging mode lets you average multiple acquisitions together to
reduce noise and increase vertical resolution (at all time/div settings).
Averaging requires a stable trigger.
The number of averages can be set from 2 to 65536 in power- of- 2
increments.
A higher number of averages reduces noise more and increases vertical
resolution.
# Avgs Bits of resolution

2 8
4 9
16 10
64 11
≥ 256 12
The higher the number of averages, the slower the displayed waveform
responds to waveform changes. You must compromise between how quickly
the waveform responds to changes and how much you want to reduce the
displayed noise on the signal.
To use the Averaging mode:
1 Press the [Acquire] key, then press the Acq Mode softkey until the
Averaging mode is selected.
2 Press the #Avgs softkey and turn the Entry knob to set the number of
averages that best eliminates the noise from the displayed waveform.
The number of acquisitions being averaged is displayed in the # Avgs
softkey.

Figure 26 Random noise on the displayed waveform
Figure 27 128 Averages used to reduce random noise

See Also • Chapter 10, “Trigger Mode/Coupling,” starting on page 133
High Resolution Acquisition Mode

In High Resolution mode, at slower time/div settings when decimation
would normally occur, extra samples are averaged in order to reduce
random noise, produce a smoother trace on the screen, and effectively
increase vertical resolution.
High Resolution mode averages sequential sample points within the same
acquisition. An extra bit of vertical resolution is produced for every factor
of 4 averages. The number of extra bits of vertical resolution is dependent
on the oscilloscope's time per division setting (sweep speed) and the
displayed sample rate.
The slower the time/div setting, the greater the number of samples that
are averaged together for each display point.
High Resolution mode can be used on both single- shot and repetitive
signals and it does not slow waveform update because the computation is
done in the MegaZoom custom ASIC. High Resolution mode limits the
oscilloscope's real- time bandwidth because it effectively acts like a
low- pass filter.
Displayed Sample Rate (sr, per Displayed Sample Rate (sr, Bits of
channel, 1 Gsa/s max) interleaved, 2 Gsa/s max) resolution
250 MSa/s < sr ≤ 1 Gsa/s 500 MSa/s < sr ≤ 2 Gsa/s 8
62.5 MSa/s < sr ≤ 250 MSa/s 125 MSa/s < sr ≤ 500 MSa/s 9
12.5 MSa/s < sr ≤ 62.5 MSa/s 25 MSa/s < sr ≤ 125 MSa/s 10
2.5 MSa/s < sr ≤ 12.5 MSa/s 5 MSa/s < sr ≤ 25 MSa/s 11
sr ≤ 2.5 MSa/s sr ≤ 5 MSa/s 12
Acquiring to Segmented Memory

You can purchase the oscilloscope with the segmented memory option
factory- installed (Option SGM) or you can install a license to enable it
(order model number DSOX2SGM "Segmented Memory").

When capturing multiple infrequent trigger events it is advantageous to

divide the oscilloscope's memory into segments. This lets you capture
signal activity without capturing long periods of signal inactivity.
Each segment is complete with all analog channel and digital channel (on
MSO models) data.
When using segmented memory, use the Analyze Segments feature (see
"Infinite Persistence with Segmented Memory" on page 155) to show
infinite persistence across all acquired segments. See also "To set or clear
persistence" on page 101 for details.
To acquire to 1 Set up a trigger condition. (See Chapter 9, “Triggers,” starting on page
segmented 111 for details.)
memory 2 Press the [Acquire] key in the Waveform section of the front panel.
3 Press the Segmented softkey.
4 In the Segmented Memory Menu, press the Segmented softkey to enable
segmented memory acquisitions.
5 Press the # of Segs softkey and turn the Entry knob to select the
number of segments into which you would like to divide the
oscilloscope's memory.
Memory can be divided into as few as two segments and as many as 25
segments.
6 Press the [Run] or [Single] key.
The oscilloscope runs and fills a memory segment for each trigger event.
When the oscilloscope is busy acquiring multiple segments, the progress is
displayed in the upper right area of the display. The oscilloscope
continues to trigger until memory is filled, then the oscilloscope stops.
If the signal you are measuring has more than about 1 s of inactivity,
consider selecting the Normal trigger mode to prevent AutoTriggering. See
"To select the Auto or Normal trigger mode" on page 134.

Progress indicator
Sample rate
See Also • "Navigating Segments" on page 155

• "Infinite Persistence with Segmented Memory" on page 155
• "Segmented Memory Re- Arm Time" on page 156
• "Saving Data from Segmented Memory" on page 156
Navigating Segments
1 Press the Current Seg softkey and turn the Entry knob to display the
desired segment along with a time tag indicating the time from the first
trigger event.
You can also navigate segments using the [Navigate] key and controls. See
"To navigate segments" on page 53.
Infinite Persistence with Segmented Memory

When data has been acquired to segmented memory, you can also turn on
infinite persistence (in the Display Menu) and press the Analyze Segments
softkey to create an infinite persistence display. The Analyze Segments
softkey appears when the acquisition is stopped and the segmented
memory feature is on.

Segmented Memory Re-Arm Time

After each segment fills, the oscilloscope re- arms and is ready to trigger
in about 8 µs.
Remember though, for example: if the horizontal time per division control
is set to 5 µs/div, and the Time Reference is set to Center, it will take at
least 50 µs to fill all ten divisions and re- arm. (That is 25 µs to capture
pre- trigger data and 25 µs to capture post- trigger data.)
Saving Data from Segmented Memory

You can save either the currently displayed segment (Save Segment -
Current), or all segments (Save Segment - All) in the following data formats:
CSV, ASCII XY, and BIN.
Be sure to set the Length control to capture enough points to accurately
represent the captured data. When the oscilloscope is busy saving multiple
segments, progress is displayed in the upper right area of the display.
For more information, see "To save CSV, ASCII XY, or BIN data files" on
page 208.

User's Guide
12
Cursors
To make cursor measurements 158
Cursor Examples 161
Cursors are horizontal and vertical markers that indicate X- axis values
and Y- axis values on a selected waveform source. You can use cursors to
make custom voltage, time, phase, or ratio measurements on oscilloscope
signals.
Cursor information is displayed in the right- side information area.
Cursors are not always limited to the visible display. If you set a cursor,
then pan and zoom the waveform until the cursor is off screen, its value
will not be changed. It will still be there when you return to its original
location.
X Cursors X cursors are vertical dashed lines that adjust horizontally and can be
used to measure time (s), frequency (1/s), phase (°), and ratio (%).
The X1 cursor is the short- dashed vertical line, and the X2 cursor is the
long- dashed vertical line.
When used with the FFT math function as a source, the X cursors
indicate frequency.
In XY horizontal mode, the X cursors display channel 1 values (Volts or
Amps).
The X1 and X2 cursor values for the selected waveform source are
displayed in the softkey menu area.
The difference between X1 and X2 (∆X) and 1/∆X are displayed in the
Cursors box in the right- side information area.
157
12 Cursors
Y Cursors Y cursors are horizontal dashed lines that adjust vertically and can be
used to measure Volts or Amps, dependent on the channel Probe Units
setting, or they can measure ratios (%). When math functions are used as
a source, the measurement units correspond to that math function.
The Y1 cursor is the short- dashed horizontal line and the Y2 cursor is the
long- dashed horizontal line.
The Y cursors adjust vertically and typically indicate values relative to the
waveform's ground point, except math FFT where the values are relative
to 0 dB.
In XY horizontal mode, the Y cursors display channel 2 values (Volts or
Amps).
When active, the Y1 and Y2 cursor values for the selected waveform
source are displayed in the softkey menu area.
The difference between Y1 and Y2 (∆Y) is displayed in the Cursors box in
the right- side information area.
To make cursor measurements

2 Press the [Cursors] key.
The Cursors box in the right- side information area appears, indicating
that cursors are "on". (Press the [Cursors] key again when you want to
turn cursors off.)
3 In the Cursors Menu, press Mode; then, select the desired mode:
• Manual — ∆X, 1/∆X, and ∆Y values are displayed. ∆X is the difference
between the X1 and X2 cursors and ∆Y is the difference between the
Y1 and Y2 cursors.

Cursors 12
• Track Waveform — As you move a marker horizontally, the vertical

amplitude of the waveform is tracked and measured. The time and
voltage positions are shown for the markers. The vertical (Y) and
horizontal (X) differences between the markers are shown as ∆X and
∆Y values.
• Binary — Logic levels of displayed waveforms at the current X1 and
X2 cursor positions are displayed above the softkeys in binary. The
display is color coded to match the color of the related channel's
waveform.
• Hex — Logic levels of displayed waveforms at the current X1 and X2

cursor positions are displayed above the softkeys in hexadecimal.
Manual and Track Waveform modes can be used on waveforms that are
displayed on the analog input channels (including math functions).
Binary and Hex modes apply to digital signals (of MSO oscilloscope
models).
In Hex and Binary modes, a level can be displayed as 1 (higher than
trigger level), 0 (lower than trigger level), indeterminate state ( ), or X
(don't care).
In Binary mode, X is displayed if the channel is turned off.
In Hex mode, the channel is interpreted as 0 if turned off.
4 Press Source (or X1 Source, X2 Source in the Track Waveform mode); then,
select the input source for cursor values.
5 Select the cursor(s) to be adjusted:
• Push the Cursors knob; then, turn the Cursors knob. To finalize your
selection, either push the Cursors knob again or wait about five
seconds for the popup menu to disappear.
Or:

12 Cursors
• Press the Cursors softkey; then, turn the Entry knob.

The X1 X2 linked and Y1 Y2 linked selections let you adjust both cursors at
the same time, while the delta value remains the same. This can be
useful, for example, for checking pulse width variations in a pulse train.
The currently selected cursor(s) display brighter than the other cursors.
6 To change the cursor units, press the Units softkey.
In the Cursor Units Menu:
You can press the X Units softkey to select:

• Seconds (s).
• Hz (1/s).
• Phase (°) — when selected, use the Use X Cursors softkey to set the
current X1 location as 0 degrees and the current X2 location as 360
degrees.
• Ratio (%) — when selected, use the Use X Cursors softkey to set the
current X1 location as 0% and the current X2 location as 100%.
You can press the Y Units softkey to select:
• Base — the same units used for the source waveform.
• Ratio (%) — when selected, use the Use Y Cursors softkey to set the
current Y1 location as 0% and the current Y2 location as 100%.
For phase or ratio units, once the 0 and 360 degree or 0 and 100%
locations are set, adjusting cursors will display measurements relative
to the set locations.
7 Adjust the selected cursor(s) by turning the Cursors knob.

Cursors 12
Cursor Examples
Figure 28 Cursors used to measure pulse widths other than middle threshold points

12 Cursors
Figure 29 Cursors measure frequency of pulse ringing
Expand the display with Zoom mode, then characterize the event of
interest with the cursors.

Cursors 12
Figure 30 Cursors track Zoom window
Put the X1 cursor on one side of a pulse and the X2 cursor on the other
side of the pulse.

12 Cursors
Figure 31 Measuring pulse width with cursors
Press the X1 X2 linked softkey and move the cursors together to check for
pulse width variations in a pulse train.

Cursors 12
Figure 32 Moving the cursors together to check pulse width variations

12 Cursors

User's Guide
13
Measurements
To make automatic measurements 168
Measurements Summary 169
Voltage Measurements 171
Time Measurements 179
Measurement Thresholds 184
Measurement Window with Zoom Display 186
The [Meas] key lets you make automatic measurements on waveforms.

Some measurements can only be made on analog input channels.
The results of the last four selected measurements are displayed in the
Measurements information area on the right- hand side of the screen.
Cursors are turned on to show the portion of the waveform being
measured for the most recently selected measurement (bottom- most on the
right- side measurement are).
Post Acquisition Processing

NOTE
In addition to changing display parameters after the acquisition, you can perform all of the
measurements and math functions after the acquisition. Measurements and math
functions will be recalculated as you pan and zoom and turn channels on and off. As you
zoom in and out on a signal using the horizontal scale knob and vertical volts/division knob,
you affect the resolution of the display. Because measurements and math functions are
performed on displayed data, you affect the resolution of functions and measurements.
167
13 Measurements
To make automatic measurements

1 Press the [Meas] key to display the Measurement Menu.
2 Press the Source softkey to select the channel, running math function,
or reference waveform to be measured.
Only channels, math functions, or reference waveforms that are
displayed are available for measurements.
If a portion of the waveform required for a measurement is not
displayed or does not display enough resolution to make the
measurement, the result will display "No Edges", "Clipped", "Low Signal",
"< value", or "> value", or a similar message to indicate that the
measurement may not be reliable.
3 Press the Type softkey then rotate the Entry knob to select a
measurement to be made.

Measurements 13
For more information on the types of measurements, see "Measurements

Summary" on page 169.
4 The Settings softkey will be available to make additional measurement
settings on some measurements.
5 Press the Add Measurement softkey or push the Entry knob to display the
measurement.
6 To turn off measurements, press the [Meas] key again.
Measurements are erased from the display.
7 To stop making one or more measurements, press the Clear Meas softkey
and choose the measurement to clear, or press Clear All.
After all measurements have been cleared, when [Meas] is pressed

again, the default measurements will be Frequency and Peak- Peak.
Measurements Summary
The automatic measurements provided by the oscilloscope are listed in the
following table. All measurements are available for analog channel
waveforms. All measurements except Counter are available for math
waveforms other than FFT. A limited set of measurements is available for
math FFT waveforms and for digital channel waveforms (as described in
the following table).
Measurement Valid Valid for Notes

for Digital
Math Channels
FFT*
"Snapshot All" on page 171
"Amplitude" on page 172
"Average" on page 176 Yes, Full
Screen

13 Measurements
Measurement Valid Valid for Notes

for Digital
Math Channels
FFT*
"Base" on page 174
"Burst Width" on page 181
"Delay" on page 182 Measures between two sources.
Press Settings to specify the
second source.
"Duty Cycle" on page 181 Yes

"Fall Time" on page 182
"Frequency" on page 180 Yes

"Maximum" on page 172 Yes
"Minimum" on page 172 Yes
"Overshoot" on page 174

"Peak-Peak" on page 172 Yes
"Period" on page 179 Yes

"Phase" on page 183 Measures between two sources.
Press Settings to specify the
second source.
"Preshoot" on page 175

"Rise Time" on page 182
"DC RMS" on page 176
"AC RMS" on page 177
"Top" on page 173
"+ Width" on page 181 Yes

"– Width" on page 181 Yes
*
Use the cursors to make other measurements on FFT.

Measurements 13
Snapshot All
The Snapshot All measurement type displays a popup containing a
snapshot of all the single waveform measurements.
You can also configure the [Quick Action] key to display the Snapshot All
popup. See "Configuring the [Quick Action] Key" on page 238.
Voltage Measurements
The following figure shows the voltage measurement points.
Maximum Top
Amplitude Peak-Peak
Base
Minimum
Measurement units for each input channel can be set to Volts or Amps
using the channel Probe Units softkey. See "To specify the channel units" on
page 60.

13 Measurements
The units of math waveforms are described in "Units for Math

Waveforms" on page 74.
• "Peak- Peak" on page 172
• "Maximum" on page 172
• "Minimum" on page 172
• "Amplitude" on page 172
• "Top" on page 173
• "Base" on page 174
• "Overshoot" on page 174
• "Preshoot" on page 175
• "Average" on page 176
• "DC RMS" on page 176
• "AC RMS" on page 177
Peak-Peak
The peak- to- peak value is the difference between Maximum and Minimum
values. The Y cursors show the values being measured.
Maximum
Maximum is the highest value in the waveform display. The Y cursor
shows the value being measured.
Minimum
Minimum is the lowest value in the waveform display. The Y cursor shows
the value being measured.
Amplitude
The Amplitude of a waveform is the difference between its Top and Base
values. The Y cursors show the values being measured.

Measurements 13
Top
The Top of a waveform is the mode (most common value) of the upper
part of the waveform, or if the mode is not well defined, the top is the
same as Maximum. The Y cursor shows the value being measured.
See Also • "To isolate a pulse for Top measurement" on page 173
To isolate a pulse for Top measurement

The following figure shows how to use Zoom mode to isolate a pulse for a
Top measurement.
You may need to change the measurement window setting so that the
measurement is made in the lower, Zoom window. See "Measurement
Window with Zoom Display" on page 186.
Figure 33 Isolating area for Top measurement

13 Measurements
Base
The Base of a waveform is the mode (most common value) of the lower
part of the waveform, or if the mode is not well defined, the base is the
same as Minimum. The Y cursor shows the value being measured.
Overshoot
Overshoot is distortion that follows a major edge transition expressed as a
percentage of Amplitude. The X cursors show which edge is being
measured (edge closest to the trigger reference point).
local Maximum − D Top

Rising edge overshοot = Amplitude × 100
Falling edge overshοot = Base − Amplitude

D local Minimum × 100
Overshoot
local Maximum
Top
Base
local Minimum Overshoot

Measurements 13
Figure 34 Automatic Overshoot measurement
Preshoot
Preshoot is distortion that precedes a major edge transition expressed as a
percentage of Amplitude. The X cursors show which edge is being
measured (edge closest to the trigger reference point).
local Maximum − D Top

Rising edge preshοot = Amplitude × 100
Falling edge preshοot = Base − Amplitude

D local Minimum × 100

13 Measurements
Preshoot
local Maximum
Top
Base
Preshoot local Minimum
Average
Average is the sum of the levels of the waveform samples divided by the
number of samples.
∑ xi
Average = n
Where xi = value at ith point being measured, n = number of points in

measurement interval.
The Full Screen measurement interval variation measures the value on all
displayed data points.
The N Cycles measurement interval variation measures the value on an
integral number of periods of the displayed signal. If less than three edges
are present, the measurement shows "No edges".
The X cursors show what interval of the waveform is being measured.
DC RMS
DC RMS is the root- mean- square value of the waveform over one or more
full periods.
n
∑i=1xi2
RMS (dc) = n
Where xi = value at ith point being measured, n = number of points in

measurement interval.
The Full Screen measurement interval variation measures the value on all
displayed data points.

Measurements 13
The N Cycles measurement interval variation measures the value on an

integral number of periods of the displayed signal. If less than three edges
are present, the measurement shows "No edges".
The X cursors show the interval of the waveform being measured.
AC RMS
AC RMS is the root- mean- square value of the waveform, with the DC
component removed. It is useful, for example, for measuring power supply
noise.
The N Cycles measurement interval measures the value on an integral
number of periods of the displayed signal. If less than three edges are
present, the measurement shows "No edges".
The X cursors show the interval of the waveform being measured.
The Full Screen (Std Deviation) measurement interval variation is an RMS
measurement across the full screen with the DC component removed. It
shows the standard deviation of the displayed voltage values.
The standard deviation of a measurement is the amount that a
measurement varies from the mean value. The Mean value of a
measurement is the statistical average of the measurement.
The following figure graphically shows the mean and standard deviation.
Standard deviation is represented by the Greek letter sigma: σ. For a
Gaussian distribution, two sigma (± 1σ) from the mean, is where 68.3
percent of the measurement results reside. Six sigma (± 3σ) from is where
99.7 percent of the measurement results reside.

13 Measurements
bZVc
-3σ -2σ -1σ % 1σ 2σ 3σ

+-#(
.*#)
..#,
The mean is calculated as follows:
N
∑i=1 xi
x̄ = N
where:
• x = the mean.
• N = the number of measurements taken.
• xi = the ith measurement result.
The standard deviation is calculated as follows:
∑i=1
N
(xi − x̄)2
σ= N
where:
• σ = the standard deviation.
• N = the number of measurements taken.
• xi = the ith measurement result.
• x = the mean.

Measurements 13
Time Measurements
The following figure shows time measurement points.
Rise Time Fall Time

Thresholds
Upper
Middle
Lower
+ Width - Width
Period
The default lower, middle, and upper measurement thresholds are 10%,
50%, and 90% between Top and Base values. See "Measurement
Thresholds" on page 184 for other percentage threshold and absolute value
threshold settings.
• "Period" on page 179
• "Frequency" on page 180
• "+ Width" on page 181
• "– Width" on page 181
• "Burst Width" on page 181
• "Duty Cycle" on page 181
• "Rise Time" on page 182
• "Fall Time" on page 182
• "Delay" on page 182
• "Phase" on page 183
Period
Period is the time period of the complete waveform cycle. The time is
measured between the middle threshold points of two consecutive,
like- polarity edges. A middle threshold crossing must also travel through
the lower and upper threshold levels which eliminates runt pulses. The X
cursors show what portion of the waveform is being measured. The Y
cursor shows the middle threshold point.

13 Measurements
Frequency
Frequency is defined as 1/Period. Period is defined as the time between
the middle threshold crossings of two consecutive, like- polarity edges. A
middle threshold crossing must also travel through the lower and upper
threshold levels which eliminates runt pulses. The X cursors show what
portion of the waveform is being measured. The Y cursor shows the
middle threshold point.
See Also • "To isolate an event for frequency measurement" on page 180
To isolate an event for frequency measurement

The following figure shows how to use Zoom mode to isolate an event for
a frequency measurement.
You may need to change the measurement window setting so that the
measurement is made in the lower, Zoom window. See "Measurement
Window with Zoom Display" on page 186.
If the waveform is clipped, it may not be possible to make the
measurement.
Figure 35 Isolating an event for Frequency measurement

Measurements 13
+ Width
+ Width is the time from the middle threshold of the rising edge to the
middle threshold of the next falling edge. The X cursors show the pulse
being measured. The Y cursor shows the middle threshold point.
– Width
– Width is the time from the middle threshold of the falling edge to the
middle threshold of the next rising edge. The X cursors show the pulse
being measured. The Y cursor shows the middle threshold point.
Burst Width
The Burst Width measurement is the time from the first edge to the last
edge on screen.
Burst width
Duty Cycle
The duty cycle of a repetitive pulse train is the ratio of the positive pulse
width to the period, expressed as a percentage. The X cursors show the
time period being measured. The Y cursor shows the middle threshold
point.
Duty cycle = +Period

Width × 100

13 Measurements
Rise Time
The rise time of a signal is the time difference between the crossing of the
lower threshold and the crossing of the upper threshold for a
positive- going edge. The X cursor shows the edge being measured. For
maximum measurement accuracy, set the horizontal time/div as fast as
possible while leaving the complete rising edge of the waveform on the
display. The Y cursors show the lower and upper threshold points.
Fall Time
The fall time of a signal is the time difference between the crossing of the
upper threshold and the crossing of the lower threshold for a
negative- going edge. The X cursor shows the edge being measured. For
maximum measurement accuracy, set the horizontal time/div as fast as
possible while leaving the complete falling edge of the waveform on the
display. The Y cursors show the lower and upper threshold points.
Delay
Delay measures the time difference from the selected edge on source 1
and the selected edge on source 2 closest to the trigger reference point at
the middle threshold points on the waveforms. Negative delay values
indicate that the selected edge of source 1 occurred after the selected
edge of source 2.
Source 1
Delay
Source 2

2 Press the Source softkey; then turn the Entry knob to select the first
analog channel source.
3 Press the Type: softkey; then, turn the Entry knob to select Delay.
4 Press the Settings softkey to select the second analog channel source
and slope for the delay measurement.
The default Delay settings measure from the rising edge of channel 1 to
the rising edge of channel 2.

Measurements 13
5 Press the Back

Back/Up key to return to the Measurement Menu.
6 Press the Add Measurement softkey to make the measurement.
The example below shows a delay measurement between the rising edge of
channel 1 and the rising edge of channel 2.
Phase
Phase is the calculated phase shift from source 1 to source 2, expressed in
degrees. Negative phase shift values indicate that the rising edge of source
1 occurred after the rising edge of source 2.
Delay
Phase = Source 1 Period × 360
Period
Source 1
Delay
Source 2

13 Measurements

2 Press the Source softkey; then turn the Entry knob to select the first
analog channel source.
3 Press the Type: softkey; then, turn the Entry knob to select Delay.
4 Press the Settings softkey to select the second analog channel source for
the phase measurement.
The default Phase settings measure from channel 1 to channel 2.
5 Press the Back

Back/Up key to return to the Measurement Menu.
6 Press the Add Measurement softkey to make the measurement.
The example below shows a phase measurement between the channel 1
and the math d/dt function on channel 1.
Measurement Thresholds
Setting measurement thresholds defines the vertical levels where
measurements will be taken on an analog channel or math waveform.

Measurements 13
Changing default thresholds may change measurement results

NOTE
The default lower, middle, and upper threshold values are 10%, 50%, and 90% of the value
between Top and Base. Changing these threshold definitions from the default values may
change the returned measurement results for Average, Delay, Duty Cycle, Fall Time,
Frequency, Overshoot, Period, Phase, Preshoot, Rise Time, +Width, and -Width.
1 From the Measurement Menu, press the Settings softkey; then, press the
Thresholds softkey to set analog channel measurement thresholds.
You can also open the Measurement Threshold Menu by pressing
[Analyze] > Features and then selecting Measurement Thresholds.
2 Press the Source softkey to select the analog channel or math waveform
source for which you want to change measurement thresholds.
Each analog channel and the math waveform can be assigned unique
threshold values.
3 Press the Type softkey to set the measurement threshold to %

(percentage of Top and Base value) or to Absolute (absolute value).
• Percentage thresholds can be set from 5% to 95%.
• The units for absolute threshold for each channel is set in the
channel probe menu.
• When the Source is set to Math: f(t), the threshold Type can only be set
to Percent.
Absolute threshold hints

TIP
• Absolute thresholds are dependent on channel scaling, probe attenuation, and probe units.
Always set these values first before setting absolute thresholds.
• The minimum and maximum threshold values are limited to on-screen values.
• If any of the absolute threshold values are above or below the minimum or maximum waveform
values, the measurement may not be valid.
4 Press the Lower softkey; then, turn the Entry knob to set the lower
measurement threshold value.

13 Measurements
Increasing the lower value beyond the set middle value will
automatically increase the middle value to be more than the lower
value. The default lower threshold is 10% or 800 mV.
If threshold Type is set to %, the lower threshold value can be set from
5% to 93%.
5 Press the Middle softkey; then, turn the Entry knob to set the middle
The middle value is bounded by the values set for lower and upper
thresholds. The default middle threshold is 50% or 1.20 V.
• If threshold Type is set to %, the middle threshold value can be set
from 6% to 94%.
6 Press the Upper softkey; then, turn the Entry knob to set the upper
Decreasing the upper value below the set middle value will
automatically decrease the middle value to be less than the upper value.
The default upper threshold is 90% or 1.50 V.
• If threshold Type is set to %, the upper threshold value can be set
from 7% to 95%.
Measurement Window with Zoom Display

When the zoomed time base is displayed, you can choose whether
measurements are made in the Main window portion of the display or the
Zoom window portion of the display.
1 Press the [Meas] key.
2 In the Measurement Menu, press the Settings softkey.
3 In the Measurement Settings Menu, press the Meas Window softkey; then,
turn the Entry knob to select from:
• Auto Select — The measurement is attempted in the lower, Zoom
window; if it cannot be made there, the upper, Main window is used.
• Main — The measurement window is the upper, Main window.
• Zoom — The measurement window is the lower, Zoom window.

User's Guide
14
Mask Testing
To create a mask from a "golden" waveform (Automask) 187
Mask Test Setup Options 189
Mask Statistics 192
To manually modify a mask file 193
Building a Mask File 196
One way to verify a waveform's compliance to a particular set of

parameters is to use mask testing. A mask defines a region of the
oscilloscope's display in which the waveform must remain in order to
comply with chosen parameters. Compliance to the mask is verified
point- by- point across the display. Mask test operates on displayed analog
channels; it does not operate on channels that are not displayed.
To enable mask test order Option LMT at time of oscilloscope purchase, or
order DSOX2MASK as a stand- alone item after oscilloscope purchase.
To create a mask from a "golden" waveform (Automask)

A golden waveform meets all chosen parameters, and it is the waveform to
which all others will be compared.
1 Configure the oscilloscope to display the golden waveform.
2 Press the [Analyze] key.
3 Press Features; then, select Mask Test.
4 Press Features again to enable mask testing.
187
14 Mask Testing
5 Press Automask.
6 In the Automask Menu, press the Source softkey and ensure the desired
analog channel is selected.
7 Adjust the mask's horizontal tolerance (± Y) and vertical tolerance

(± X). These are adjustable in graticule divisions or in absolute units
(volts or seconds), selectable using the Units softkey.
8 Press the Create Mask softkey.
The mask is created and testing begins.
Whenever the Create Mask softkey is pressed the old mask is erased and
a new mask is created.

Mask Testing 14
9 To clear the mask and switch off mask testing, press the Back Back/Up
key to return to the Mask Test Menu, then press the Clear Mask softkey.
If infinite persistence display mode (see "To set or clear persistence" on
page 101) is "on" when mask test is enabled, it stays on. If infinite
persistence is "off" when mask test is enabled, it is switched on when
mask test is switched on, then infinite persistence is switched off when
mask test is switched off.
Troubleshooting If you press Create Mask and the mask appears to cover the entire screen,
Mask Setup check the ± Y and ± X settings in the Automask Menu. If these are set to
zero the resulting mask will be extremely tight around the waveform.
If you press Create Mask and it appears that no mask was created, check
the ± Y and ± X settings. They may be set so large that the mask is not
visible.
Mask Test Setup Options

From the Mask Test Menu, press the Setup softkey to enter the Mask Setup
Menu.

14 Mask Testing
Run Until The Run Until softkey lets you specify a condition on which to terminate
testing.
• Forever — The oscilloscope runs continuously. However, if an error occurs
the action specified using the On Error softkey will occur.
• Minimum # of Tests — Choose this option and then use the # of Tests
softkey to select the number of times the oscilloscope will trigger, display
the waveform(s), and compare them to the mask. The oscilloscope will
stop after the specified number of tests have been completed. The
specified minimum number of tests may be exceeded. If an error occurs the
action specified using the On Error softkey will occur. The actual number of
tests completed is displayed above the softkeys.
• Minimum Time — Choose this option and then use the Test Time softkey
to select how long the oscilloscope will run. When the selected time has
passed the oscilloscope will stop. The specified time may be exceeded. If
an error occurs the action specified using the On Error softkey will occur.
The actual test time is displayed above the softkeys.
• Minimum Sigma — Choose this option and then use the Sigma softkey to
select a minimum sigma. The mask test runs until enough waveforms are
tested to achieve a minimum test sigma. (If an error occurs the
oscilloscope will perform the action specified by the On Error softkey.)
Note that this is a test sigma (the max achievable process sigma,
assuming no defects, for a certain number of tested waveforms) as
opposed to a process sigma (which is tied to the amount of failures per
test). The sigma value may exceed the selected value when a small sigma
value is chosen. The actual sigma is displayed.

Mask Testing 14
On Error The On Error setting specifies the action(s) to take when the input waveform
does not conform to the mask. This setting supersedes the Run Until setting.
• Stop — The oscilloscope will stop when the first error is detected (on the
first waveform that does not conform to the mask). This setting
supersedes the Minimum # of Tests and Minimum Time settings.
• Save — The oscilloscope saves the screen image when an error is
detected. In the Save Menu (press [Save/Recall] > Save), select an
image format (*.bmp or *.png), destination (on a USB storage device), and
file name (which can be auto-incrementing). If errors occur too frequently
and the oscilloscope spends all its time saving images, press the [Stop]
key to stop acquisitions.
• Print — The oscilloscope prints the screen image when an error is
detected. This option is only available when a printer is connected as
described in "To print the oscilloscope's display" on page 219.
• Measure — Measurements (and measurement statistics if your
oscilloscope supports them) run only on waveforms that contain a mask
violation. Measurements are not affected by passing waveforms. This
mode is not available when the acquisition mode is set to Averaging.
Note that you can choose to Print or Save, but you cannot select both at the
same time. All other actions may be selected at the same time. For example,
you can select both Stop and Measure to cause the oscilloscope to measure
and stop on the first error..
You can also output a signal on the rear panel TRIG OUT BNC connector when
there is a mask test failure. See "Setting the Rear Panel TRIG OUT Source" on
page 232.
Source Lock When you turn on Source Lock using the Source Lock softkey, the mask is
redrawn to match the source whenever you move the waveform. For example,
if you change the horizontal timebase or the vertical gain the mask is redrawn
with the new settings.
When you turn off Source Lock, the mask is not redrawn when horizontal or
vertical settings are changed.
Source If you change the Source channel, the mask is not erased. It is re-scaled to the
vertical gain and offset settings of the channel to which it is assigned. To
create a new mask for the selected source channel, go back up in the menu
hierarchy; then, press Automask, and press Create Mask.
The Source softkey in the Mask Setup Menu is the same as the Source
softkey in the Automask Menu.
Test All When enabled, all displayed analog channels are included in the mask test.
When disabled, just the selected source channel is included in the test.

14 Mask Testing
Mask Statistics
From the Mask Test Menu, press the Statistics softkey to enter the Mask
Statistics Menu.
Show Stats When you enable Show Statistics the following information is displayed:
• Current mask, name of mask, Channel number, date and time.
• # of Tests (total number of mask tests executed).
• Status (Passing, Failing, or Untested).
• Accumulated test time (in hours, minutes, seconds, and tenths of
seconds).
And for each analog channel:
• Number of failures (acquisitions in which the signal excursion went
beyond the mask).
• Failure rate (percentage of failures).
• Sigma (the ratio of process sigma to maximum achievable sigma, based on
number of waveforms tested).

Mask Testing 14
Reset Statistics Note that statistics are also reset when:

• Mask Test is switched on after being switched off.
• Clear Mask softkey is pressed.
• An Automask is created.
Additionally, the accumulated time counter is reset whenever the
oscilloscope is run after the acquisition was stopped.
Transparent Enable Transparent mode to write measurement values and statistics on the
screen without a background. Disable the Transparent mode to show them
with a gray background. The Transparent setting affects mask test statistics,
measurement statistics, and reference waveform information display.
Clear Display Clears acquisition data from the oscilloscope display.
To manually modify a mask file

You can manually modify a mask file that you created using the Automask
function.
1 Follow the steps 1- 7 in "To create a mask from a "golden" waveform
(Automask)" on page 187. Do not clear the mask after creating it.
2 Attach a USB mass storage device to the oscilloscope.
3 Press the [Save/Recall] key.
4 Press the Save softkey.
5 Press the Format softkey and select Mask.
6 Press the second softkey and select a destination folder on your USB
mass storage device.
7 Press the Press to Save softkey. This creates an ASCII text file that
describes the mask.
8 Remove the USB mass storage device and connect it to a PC.
9 Open the .msk file your created using a text editor (such as Wordpad).
10 Edit, save, and close the file.
The mask file contains the following sections:
• Mask File Identifier.
• Mask Title.
• Mask Violation Regions.

14 Mask Testing
• Oscilloscope Setup Information.

Mask File The Mask File Identifier is MASK_FILE_548XX.
Identifier
Mask Title The Mask Title is a string of ASCII characters. Example: autoMask CH1
OCT 03 09:40:26 2008
When a mask file contains the keyword "autoMask" in the title, the edge of
the mask is passing by definition. Otherwise, the edge of the mask is
defined as a failure.
Mask Violation
Regions
Region 1
Region 2
Up to 8 regions can be defined for a mask. They can be numbered 1- 8.

They can appear in any order in the .msk file. The numbering of the
regions must go from top to bottom, left to right.
An Automask file contains two special regions: the region "glued" to the
top of the display, and the region that is "glued" to the bottom. The top
region is indicated by y- values of "MAX" for the first and last points. The
bottom region is indicated by y- values of "MIN" for the first and last
points.
The top region must be the lowest numbered region in the file. The
bottom region must be the highest numbered region in the file.

Mask Testing 14
Region number 1 is the top mask region. The vertices in Region 1 describe
points along a line; that line is the bottom edge of the top portion of the
mask.
Similarly, the vertices in Region 2 describe the line that forms the top of
the bottom part of the mask.
The vertices in a mask file are normalized. There are four parameters that
define how values are normalized:
• X1
• ∆X
• Y1
• Y2
These four parameters are defined in the Oscilloscope Setup portion of the
mask file.
The Y- values (normally voltage) are normalized in the file using the
following equation:
Ynorm = (Y - Y1)/∆Y
where ∆Y = Y2 - Y1
To convert the normalized Y- values in the mask file to voltage:
Y = (Ynorm * ∆Y) + Y1
where ∆Y = Y2 - Y1
The X- values (normally time) are normalized in the file using the
following equation:
Xnorm = (X - X1)/∆X
To convert the normalized X- values to time:

X = (Xnorm * ∆X) + X1
Oscilloscope The keywords "setup" and "end_setup" (appearing alone on a line) define
Setup Information the beginning and end of the oscilloscope setup region of the mask file.
The oscilloscope setup information contains remote programming language
commands that the oscilloscope executes when the mask file is loaded.
Any legal remote programming command can be entered in this section.

14 Mask Testing
The mask scaling controls how the normalized vectors are interpreted.
This in turn controls how the mask is drawn on the display. The remote
programming commands that control mask scaling are:
:MTES:SCAL:BIND 0
:MTES:SCAL:X1 -400.000E-06
:MTES:SCAL:XDEL +800.000E-06
:MTES:SCAL:Y1 +359.000E-03
:MTES:SCAL:Y2 +2.35900E+00
Building a Mask File

The following mask uses all eight mask regions. The most difficult part of
creating a mask file is normalizing the X and Y values from the time and
voltage values. This example shows an easy way to convert voltage and
time to normalized X and Y values in the mask file.
The following mask file produced the mask shown above:

MASK_FILE_548XX
"All Regions"
/* Region Number */ 1
/* Number of vertices */ 4
-12.50, MAX
-10.00, 1.750

Mask Testing 14
10.00, 1.750
12.50, MAX
-10.00, 1.000
-12.50, 0.500
-15.00, 0.500
-15.00, 1.500
-12.50, 1.500
-05.00, 1.000
-02.50, 0.500
02.50, 0.500
05.00, 1.000
02.50, 1.500
-02.50, 1.500
10.00, 1.000
12.50, 0.500
15.00, 0.500
15.00, 1.500
12.50, 1.500
-10.00, -1.000
-12.50, -0.500
-15.00, -0.500
-15.00, -1.500
-12.50, -1.500
-05.00, -1.000
-02.50, -0.500
02.50, -0.500
05.00, -1.000
02.50, -1.500
-02.50, -1.500
10.00, -1.000
12.50, -0.500
15.00, -0.500
15.00, -1.500
12.50, -1.500
-12.50, MIN
-10.00, -1.750
10.00, -1.750
12.50, MIN
setup
:MTES:ENAB 1

14 Mask Testing
:CHAN1:RANG +4.00E+00;OFFS +0.0E+00;COUP DC;IMP ONEM;DISP 1;BWL 0;INV 0

:CHAN1:LAB "1";UNIT VOLT;PROB +1.0E+00;PROB:SKEW +0.0E+00;STYP SING
:CHAN2:RANG +16.0E+00;OFFS +1.62400E+00;COUP DC;IMP FIFT;DISP 0;BWL 0;INV
0
:EXT:BWL 0;IMP ONEM;RANG +5E+00;UNIT VOLT;PROB +1.0E+00;PROB:STYP SING
:TIM:MODE MAIN;REF CENT;MAIN:RANG +50.00E-09;POS +0.0E+00
:TRIG:MODE EDGE;SWE AUTO;NREJ 0;HFR 0;HOLD +60E-09
:TRIG:EDGE:SOUR CHAN1;LEV -75.00E-03;SLOP POS;REJ OFF;COUP DC
:ACQ:MODE RTIM;TYPE NORM;COMP 100;COUNT 8;SEGM:COUN 2
:DISP:LAB 0;CONN 1;PERS MIN;SOUR PMEM1
:HARD:APR "";AREA SCR;FACT 0;FFE 0;INKS 1;PAL NONE;LAY PORT
:SAVE:FIL "mask_0"
:SAVE:IMAG:AREA GRAT;FACT 0;FORM NONE;INKS 0;PAL COL
:SAVE:WAV:FORM NONE
:MTES:SOUR CHAN1;ENAB 1;LOCK 1
:MTES:AMAS:SOUR CHAN1;UNIT DIV;XDEL +3.00000000E-001;YDEL +2.00000000E-00
1
:MTES:SCAL:BIND 0;X1 +0.0E+00;XDEL +1.0000E-09;Y1 +0.0E+00;Y2 +1.00000E+0
0
:MTES:RMOD FOR;RMOD:TIME +1E+00;WAV 1000;SIGM +6.0E+00
:MTES:RMOD:FACT:STOP 0;PRIN 0;SAVE 0
end_setup
How is mask testing done?

InfiniiVision oscilloscopes start mask testing by creating a database that is
200 x 640 for the waveform viewing area. Each location in the array is
designated as either a violation or a pass area. Each time a data point
from a waveform occurs in a violation area a failure is logged. If Test All
was selected, every active analog channel is tested against the mask
database for each acquisition. Over 2 billion failures can be logged
per- channel. The number of acquisitions tested is also logged and
displayed as "# of Tests".
The mask file allows greater resolution than the 200 X 640 database. Some
quantization of data occurs to reduce the mask file data for display
on- screen.

User's Guide
15
Waveform Generator
To select generated waveform types and settings 199
To output the waveform generator sync pulse 202
To specify the waveform generator output load 203
To use waveform generator logic presets 203
To restore waveform generator defaults 204
A waveform generator is built into the oscilloscope. It is enabled by

Option WGN or the DSOX2WAVEGEN upgrade. The waveform generator
gives you an easy way to provide input signals when testing circuitry with
the oscilloscope.
Waveform generator settings can be saved and recalled with oscilloscope
setups. See Chapter 16, “Save/Recall (Setups, Screens, Data),” starting on
page 205.
To select generated waveform types and settings

1 To access the Waveform Generator Menu and enable or disable the
waveform generator output on the front panel Gen Out BNC, press the
[Wave Gen] key.
When waveform generator output is enabled, the [Wave Gen] key is
illuminated. When waveform generator output is disabled, the [Wave
Gen] key is off.
The waveform generator output is always disabled when the instrument
is first turned on.
199
The waveform generator output is automatically disabled if excessive

voltage is applied to the Gen Out BNC.
2 In the Waveform Generator Menu, press the Waveform softkey and turn
the Entry knob to select the waveform type.
3 Depending on the selected waveform type, use the remaining softkeys

and the Entry knob to set the waveform's characteristics.

Waveform Generator 15
Waveform Characteristics
Type
Sine Use the Frequency/Frequency Fine/Period/Period Fine,
Amplitude/High-Level, and Offset/Low-Level softkeys to set the sine signal
parameters.
The frequency can be adjusted from 100 mHz to 20 MHz.
Square Use the Frequency/Frequency Fine/Period/Period Fine,
Amplitude/High-Level, Offset/Low-Level, and Duty Cycle softkeys to set the
square wave signal parameters.
The duty cycle can be adjusted from 20% to 80%.
Ramp Use the Frequency/Frequency Fine/Period/Period Fine,
Amplitude/High-Level, Offset/Low-Level, and Symmetry softkeys to set the
ramp signal parameters.
The frequency can be adjusted from 100 mHz to 100 kHz.
Symmetry represents the amount of time per cycle that the ramp waveform is
rising and can be adjusted from 0% to 100%.
Pulse Use the Frequency/Frequency Fine/Period/Period Fine,

Amplitude/High-Level, Offset/Low-Level, and Width/Width Fine softkeys to
set the pulse signal parameters.
The pulse width can be adjusted from 20 ns to the period minus 20 ns.
DC Use the Offset softkey to set the DC level.
Noise Use the Amplitude/High-Level and Offset/Low-Level to set the noise signal
parameters.
For all waveform types, the output amplitude, into 50 Ω, can be

adjusted from 10 mVpp to 2.5 Vpp (or from 20 mVpp to 5 Vpp into an
open- circuit load).
Pressing a signal parameter softkey can open a menu for selecting the
type of adjustment. For example, you can choose to enter amplitude
and offset values, or you can choose to enter high- level and low- level
values. Or, you can choose to enter frequency values or period values.
Keep pressing the softkey to select the type of adjustment. Turn the
Entry knob to adjust the value.

Notice that you can select between coarse and fine adjustments for
frequency, period, and width. Also, pushing the Entry knob is a quick
way to toggle between coarse and fine adjustments.
The Settings softkey opens the Waveform Generator Settings Menu which
lets you make other settings related to the waveform generator.
See:
• "To output the waveform generator sync pulse" on page 202
• "To specify the waveform generator output load" on page 203
• "To use waveform generator logic presets" on page 203
• "To restore waveform generator defaults" on page 204
To output the waveform generator sync pulse

1 If the Waveform Generator Menu is not currently displayed on the
oscilloscope's softkeys, press the [Wave Gen] key.
2 In the Waveform Generator Menu, press the Settings softkey.
3 In the Waveform Generator Settings Menu, press the Trig Out softkey and
turn the Entry knob to select Waveform Generator Sync Pulse.
Waveform Type Sync Signal Characteristics

All waveforms except The Sync signal is a TTL positive pulse that occurs when the waveform
DC and Noise rises above zero volts (or the DC offset value).
DC N/A
Noise N/A

Waveform Generator 15
To specify the waveform generator output load

3 In the Waveform Generator Settings Menu, press the Out Load softkey
and turn the Entry knob to select:
• 50 Ω
• High-Z
The output impedance of the Gen Out BNC is fixed at 50 ohms. However,
the output load selection lets the waveform generator display the correct
amplitude and offset levels for the expected output load.
If the actual load impedance is different than the selected value, the
displayed amplitude and offset levels will be incorrect.
To use waveform generator logic presets

With logic level presets, you can easily set the output voltage to TTL,
CMOS (5.0V), CMOS (3.3V), CMOS (2.5V), or ECL compatible Low and High
levels.
3 In the Waveform Generator Settings Menu, press the Logic Presets
softkey.
4 In the Waveform Generator Logic Level Presets Menu, press one of the
softkeys to set the generated signal's Low and High voltages to logic
compatible levels:

Softkey (logic levels) Low level High level, 50 ohm High level, high-Z
expected output load expected output load
TTL 0V +2.5 V (TTL compatible) +5 V
CMOS (5.0V) 0V Not Available +5 V
CMOS (3.3V) 0V +2.5 V (CMOS +3.3 V
compatible)
CMOS (2.5V) 0V +2.5 V +2.5 V
ECL -1.7 V -0.8 V (ECL compatible) -0.9 V
To restore waveform generator defaults

3 In the Waveform Generator Settings Menu, press the Default Wave Gen
softkey.
The waveform generator factory default settings (1 kHz sine wave,
500 mVpp, 0 V offset, High- Z output load) are restored.

User's Guide
16
Save/Recall (Setups, Screens, Data)
Saving Setups, Screen Images, or Data 205
Recalling Setups, Masks, or Reference Waveforms 215
Recalling Default Setups 216
Performing a Secure Erase 217
Oscilloscope setups, reference waveforms, and mask files can be saved to

internal oscilloscope memory or to a USB storage device and recalled
later. You can also recall default or factory default setups.
Oscilloscope screen images can be saved to a USB storage device in BMP
or PNG formats.
Acquired waveform data can be saved to a USB storage device in
comma- separated value (CSV), ASCII XY, binary (BIN), and Agilent logic
analyzer binary (ALB) formats.
There is also a command to securely erase all the oscilloscope's
non- volatile internal memory.
Saving Setups, Screen Images, or Data

2 In the Save/Recall Menu, press Save.
3 In the Save Trace and Setup Menu, press Format, then, turn the Entry
knob to select the type of file you want to save:
205
• Setup (*.scp) — The oscilloscope's horizontal timebase, vertical

sensitivity, trigger mode, trigger level, measurements, cursors, and
math function settings that tell the oscilloscope how to make a
particular measurement. See "To save setup files" on page 207.
• 8-bit Bitmap image (*.bmp) — The complete screen image in a reduced
color (8- bit) bitmap format. See "To save BMP or PNG image files" on
page 207.
• 24-bit Bitmap image (*.bmp) — The complete screen image in a 24- bit
color bitmap format. See "To save BMP or PNG image files" on
page 207.
• 24-bit image (*.png) — The complete screen image in a 24- bit color PNG
format that uses lossless compression. Files are much smaller than
the BMP format. See "To save BMP or PNG image files" on page 207.
• CSV data (*.csv) — This creates a file of comma- separated values of all
displayed channels and math waveforms. This format is suitable for
spreadsheet analysis. See "To save CSV, ASCII XY, or BIN data
files" on page 208.
• ASCII XY data (*.csv) — This creates separate files of comma- separated
values for each displayed channel. This format is also suitable for
spreadsheets. See "To save CSV, ASCII XY, or BIN data files" on
page 208.
• Reference Waveform data (*.h5) — Saves waveform data in a format that
can be recalled to one of the oscilloscope's reference waveform
locations. See "To save reference waveform files to a USB storage
device" on page 213.
• ALB data (*.alb) — This creates an Agilent proprietary format file that
can be imported by the Agilent Logic Analyzer application software,
using the Agilent B4610A Data Import tool, for offline viewing and
analysis. See "To save ALB data files" on page 209.
• Binary data (*.bin) — This creates a binary file, with a header, and data
in the form of time and voltage pairs. This file is much smaller than
the ASCII XY data file. See "To save CSV, ASCII XY, or BIN data
files" on page 208.

Save/Recall (Setups, Screens, Data) 16
• Mask (*.msk) — This creates a mask file in an Agilent proprietary

format that can be read by Agilent InfiniiVision oscilloscopes. A mask
data file includes some oscilloscope setup information, but not all
setup information. To save all setup information including the mask
data file, choose "Setup (*.scp)" format instead. See "To save
masks" on page 213.
You can also configure the [Quick Action] key to save setups, screen images,
or data. See "Configuring the [Quick Action] Key" on page 238.
To save setup files

Setup files can be saved to one of 10 internal (\Agilent Flash) locations or
to an external USB storage device.
1 Press [Save/Recall] > Save > Format; then, turn the Entry knob to select
Setup (*.scp).
2 Press the softkey in the second position and use the Entry knob to
navigate to the save location. See "To navigate storage locations" on
page 214.
3 Finally, press the Press to Save softkey.
A message indicating whether the save was successful is displayed.
Setup files have the extension SCP. These extensions appear when using
the File Explorer (see "File Explorer" on page 227), but they do not
appear when using the Recall Menu.
To save BMP or PNG image files

Image files can be saved to an external USB storage device.
8-bit Bitmap image (*.bmp), 24-bit Bitmap image (*.bmp), or 24-bit image (*.png).
page 214.
In the File Settings Menu, you have these softkeys and options:

• Setup Info — setup information (vertical, horizontal, trigger, acquisition,

math, and display settings) is also saved in a separate file with a
TXT extension.
• Invert Grat — the graticule in the image file has a white background
instead of the black backgound that appears on- screen.
Graticule Not Inverted Graticule Inverted
• Palette — lets you choose between Color or Grayscale images.

When saving screen images, the oscilloscope uses the last menu visited before pressing
NOTE the [Save/Recall] key. This lets you save any relevant information within the softkey menu
area.
To save a screen image showing the Save/Recall Menu at the bottom, press the
[Save/Recall] key twice before saving the image.
You can also save the oscilloscope's display image using a web browser. See "Get
NOTE Image" on page 249 for details.
To save CSV, ASCII XY, or BIN data files

Data files can be saved to an external USB storage device.
CSV data (*.csv), ASCII XY data (*.csv), or Binary data (*.bin).
page 214.


• Setup Info — when enabled, setup information (vertical, horizontal,
trigger, acquisition, math, and display settings) is also saved in a
separate file with a TXT extension.
• Length — sets the number of data points that will be output to the
file. For more information, see "Length Control" on page 211.
• Save Seg — when data is acquired to segmented memory, you can
specify whether the currently displayed segment is saved or all
acquired segments are saved. (See also "Saving Data from Segmented
Memory" on page 156.)
See Also • "Binary Data (.bin) Format" on page 262
• "CSV and ASCII XY files" on page 269
• "Minimum and Maximum Values in CSV Files" on page 270
To save ALB data files

Agilent logic analyzer binary (ALB) format data files can be viewed and
analyzed offline on a PC using the Agilent Logic Analyzer application and
the Agilent B4610A Data Import Tool. See the "Agilent Technologies
B4610A Data Import Tool for Offline Viewing and Analysis Data Sheet
(publication number 5989- 7834EN)".
ALB data files can be saved to an external USB storage device.
ALB data (*.alb).
page 214.
• Setup Info — when enabled, setup information (vertical, horizontal,
trigger, acquisition, math, and display settings) is also saved in a
separate file with a TXT extension.

• Length — sets the number of data points that will be output to the
file. For more information, see "Length Control" on page 211.
• Alb Format — Available ALB serial formats include:
• Default
• CAN
• I2C
• LIN
• UART/RS232
• SPI (2 Wire Serial)
When you choose any ALB format other than Default, waveforms
from the analog channels (if displayed) are also digitized and
displayed as digital waveforms. The analog channel's trigger level
determines the point at which the voltage is considered a logic 1 or
0.
If you connect your serial bus signals to the oscilloscope as shown in
the following table, the bus/signal names in the Agilent Logic
Analyzer application will be correct. Otherwise, you must re- map the
signals in the Agilent Logic Analyzer application.

Table 5 Recommended Signal Mapping
Label Signal Oscilloscope Maps to Logic

Channel Analyzer Channel
TxRS232 Tx Ch1 D0
RxRS232 Rx Ch2 D1
I2C Data Ch1 D0

Clk Ch2 D1
SPI2 (2-wire) Clk Ch1 D0

Data Ch2 D1
SPI3 (3-wire) ~Chip Select Ch1 D0
Clk Ch2 D1
Data Ch3 D2
SPI4 (4-wire) ~Chip Select Ch1 D0

Clk Ch2 D1
DataIn Ch3 D2
DataOut Ch4 D3
CAN Data Ch1 D0

LIN Data Ch1 D0

Length Control
The Length control is available when saving data to CSV, ASCII XY, BIN, or
ALB format files. It sets the number of data points that will be output to
the file. Only displayed data points are saved.
The maximum number of data points depends on these things:

• Whether acquisitions are running. When stopped, data comes from the
raw acquisition record. When running, data comes from the smaller
measurement record.
• Whether the oscilloscope was stopped using [Stop] or [Single]. Running
acquisitions split memory to provide fast waveform update rates. Single
acquisitions use full memory.
• Whether only one channel of a pair is turned on. (Channels 1 and 2 are
one pair, channels 3 and 4 are the other.) Acquisition memory is
divided among the channels in a pair.
• Whether reference waveforms are on. Displayed reference waveforms
consume acquisition memory.
• Whether digital channels are on. Displayed digital channels consume
acquisition memory.
• Whether segmented memory is on. Acquisition memory is divided by
the number of segments.
• The horizontal time/div (sweep speed) setting. At faster settings, fewer
data points appear on the display.
• When saving to a CSV format file, the maximum number of data points
is 50,000.
When necessary, the Length control performs a "1 of n" decimation of the
data . For example: if the Length is set to 1000, and you are displaying a
record that is 5000 data points in length, four of each five data points will
be decimated, creating an output file 1000 data points in length.
When saving waveform data, the save times depend on the chosen format:
Data File Format Save Times

BIN, ALB fastest
ASCII XY medium
CSV slowest
See Also • "Binary Data (.bin) Format" on page 262

• "CSV and ASCII XY files" on page 269

To save reference waveform files to a USB storage device

2 In the Save/Recall Menu, press the Save softkey.
3 In the Save Menu, press the Format softkey and turn the Entry knob to
select Reference Waveform data (*.h5) .
4 Press the Source softkey and turn the Entry knob to select the source
waveform.
page 214.
To save masks
Mask files can be saved to one of four internal (\Agilent Flash) locations
or to an external USB storage device.
Mask (*.msk).
page 214.
Mask files have the extension MSK.
Masks are also saved as part of setup files. See "To save setup files" on page 207.
NOTE
See Also • Chapter 14, “Mask Testing,” starting on page 187

To navigate storage locations

When saving or recalling files, the softkey in the second position of the
Save Menu or Recall Menu, along with the Entry knob, are used to
navigate to storage locations. The storage locations can be internal
oscilloscope storage locations (for setup files or mask files) or they can be
external storage locations on a connected USB storage device.
The softkey in the second position can have these labels:
• Press to go — when you can push the Entry knob to navigate to a new
folder or storage location.
• Location — when you have navigated to the current folder location (and
are not saving files).
• Save to — when you can save to the selected location.
• Load from — when you can recall from the selected file.
When saving files:
• The proposed file name is shown in the Save to file = line above the
softkeys.
• To overwrite an existing file, browse to that file and select it. To create
a new file name, see "To enter file names" on page 214.
To enter file names

To create new file names when saving files to a USB storage device:
1 In the Save Menu, press the File Name softkey.
You must have a USB storage device connected to the oscilloscope for
this softkey to be active.
2 In the File Name Menu, use the Spell, Enter, and Delete Character softkeys
to enter the file name:
• Spell — press this softkey and turn the Entry knob to select the
character at the current position.
• Enter — press this softkey to enter characters and move the cursor to
the next character position. Pushing the Entry knob is the same as
pressing the Enter softkey.
• Delete Character — press this softkey to delete the character at the
current position.

When available, the Increment softkey can be used to enable or disable

automatically incremented file names. Auto increment adds a numeric
suffix to your file name and increments the number with each
successive save. It will truncate characters as necessary when the file
name length is at maximum and more digits are required for the
numeric portion of the file name.
Recalling Setups, Masks, or Reference Waveforms

2 In the Save/Recall Menu, press Recall.
3 In the Recall Menu, press Recall:, then, turn the Entry knob to select
the type of file you want to recall:
• Setup (*.scp) — See "To recall setup files" on page 215.
• Mask (*.msk) — See "To recall mask files" on page 216.
• Reference Waveform data (*.h5) — See "To recall reference waveform files
from a USB storage device" on page 216.
You can also recall setups and mask files by loading them using the File
Explorer. See "File Explorer" on page 227.
You can also configure the [Quick Action] key to recall setups, masks, or
reference waveforms. See "Configuring the [Quick Action] Key" on
page 238.
To recall setup files

Setup files can be recalled from one of 10 internal (\Agilent Flash)
locations or from an external USB storage device.
1 Press [Save/Recall] > Recall > Recall:; then, turn the Entry knob to select
Setup (*.scp).
navigate to the file to recall. See "To navigate storage locations" on
page 214.
3 Press the Press to Recall softkey.
A message indicating whether the recall was successful is displayed.

4 If you would like to clear the display, press Clear Display.
To recall mask files

Mask files can be recalled from one of four internal (\Agilent Flash)
locations or from an external USB storage device.
1 Press [Save/Recall] > Recall > Recall:; then, turn the Entry knob to select
Mask (*.msk).
page 214.
4 If you would like to clear the display or clear the recalled mask, press
Clear Display or Clear Mask.
To recall reference waveform files from a USB storage device

2 In the Save/Recall Menu, press the Recall softkey.
3 In the Recall Menu, press the Recall softkey and turn the Entry knob to
select Reference Waveform data (*.h5) .
4 Press the To Ref: softkey and turn the Entry knob to select the desired
reference waveform location.
page 214.
7 If you would like to clear the display of everything except the reference
waveform, press Clear Display.
Recalling Default Setups


2 In the Save/Recall Menu, press Default/Erase.

3 In the Default Menu, press one of these softkeys:
• Default Setup— recalls the oscilloscope's default setup. This is the same
as pressing the front panel [Default Setup] key. See "Recall the Default
Oscilloscope Setup" on page 25.
Some user settings are not changed when recalling the default setup.
• Factory Default— recalls the oscilloscope's factory default settings.
You must confirm the recall because there are no user settings that
are left unchanged.
Performing a Secure Erase

2 In the Save/Recall Menu, press Default/Erase.
3 In the Default menu, press Secure Erase.
This performs a secure erase of all non- volatile memory in compliance
with National Industrial Security Program Operation Manual (NISPOM)
Chapter 8 requirements.
You must confirm the secure erase, and the oscilloscope will reboot
when finished.


User's Guide
17
Print (Screens)
To print the oscilloscope's display 219
To set up network printer connections 220
To specify the print options 221
To specify the palette option 222
You can print the complete display, including the status line and softkeys,
to a USB printer or a network printer when the DSOXLAN LAN/VGA
module is installed.
The Print Configuration Menu is displayed when you press the [Print] key.
The print option softkeys and the Press to Print softkey are ghosted (not
available) until a printer is connected.
To print the oscilloscope's display

1 Connect a printer. You can:
• Connect a USB printer to either the USB port on the front panel or
the rectangular USB host port on the rear panel.
For the most up- to- date listing of printers that are compatible with
the InfiniiVision oscilloscopes, please visit
"www.agilent.com/find/InfiniiVision- printers".
• Set up a network printer connection. See "To set up network printer
connections" on page 220.
2 Press the [Print] key on the front panel.
3 In the Print Configuration Menu, press the Print to softkey; then, turn
the Entry knob to select the desired printer.
219
17 Print (Screens)
4 Press the Options softkey to select the print options.
See "To specify the print options" on page 221.

5 Press the Palette softkey to select the print palette. See "To specify the
palette option" on page 222.
6 Press the Press to Print softkey.
You can stop printing by pressing the Cancel Print softkey.
The oscilloscope will print the last menu visited before you pressed the [Print] key.
NOTE Therefore, if you have measurements (Amplitude, Frequency, etc.) showing on the display
before you press [Print], the measurements will be shown on the printout.
To print the display showing the Print Configuration Menu at the bottom, press the [Print]
key twice; then, press the Press to Print softkey.
You can also configure the [Quick Action] key to print the display. See
"Configuring the [Quick Action] Key" on page 238.
To set up network printer connections

When the DSOXLAN LAN/VGA module is installed, you can set up
network printer connections.
A network printer is a printer attached to a computer or print server on
the network.
1 Press the [Print] key on the front panel.
2 In the Print Configuration Menu, press the Print to softkey; then, turn
the Entry knob to select the network printer you want to configure
(either #0 or #1).

Print (Screens) 17
3 Press the Network Setup softkey.

4 In the Network Printer Setup Menu, press the Modify softkey; then, turn
the Entry knob to select the network parameter you want to enter.
The settings that must be entered are:
• Network Domain — this is the Windows network domain name.
• Username — this is your login name for the Windows network domain.
• Password — this is your login password for the Windows network
domain.
To clear an entered password, press the Clear Password softkey.
• Printer Address — this is the server or computer name and the
printer's share name in the "\\server\share" format.
The Network Domain, Username, and Password settings are common for all
network printers.
5 Use the Spell, Enter, and Delete Character softkeys to enter the network
printer settings:
• Spell — press this softkey and turn the entry knob to select the
character at the current position.
• Enter — press this softkey to enter characters and move the cursor to
the next character position.
• Delete Character — press the Enter softkey until the desired character is
highlighted; then, press this softkey to delete the character.
6 Press the Apply softkey to make the printer connection.
A message appears to tell you whether the connection was successful.
To specify the print options

In the Print Configuration Menu, press the Options softkey to change the
following options:
• Setup Information — Select this to print oscilloscope setup information on
your printout, including vertical, horizontal, trigger, acquisition, math,
and display settings.

17 Print (Screens)
• Invert Graticule Colors — Select this to reduce the amount of black ink it
takes to print oscilloscope images by changing the black background to
white. Invert Graticule Colors is the default mode.
Graticule Not Inverted Graticule Inverted
• Form Feed — Select this to send a form feed command to the printer
after the waveform is printed and before the setup information is
printed. Switch Form Feed off if you want setup information printed on
the same sheet of paper with the waveform. This option only has an
effect when the Setup Information option is selected. Also, if the amount
of setup information will not fit on the same page with the waveform, it
will be printed on a new page regardless of the Form Feed setting.
• Landscape — Select this to print horizontally on the page instead of
vertically (portrait mode).
To specify the palette option

In the Print Configuration Menu, press the Palette softkey to change the
following options.
• Color — Select this to print the screen in color.
The oscilloscope's print driver cannot print color images to color laser
printers, so the Color option is not available when connected to laser
printers.
• Grayscale — Select this to print the screen in shades of gray rather than
in color.

User's Guide
18
Utility Settings
I/O Interface Settings 223
Setting up the Oscilloscope's LAN Connection 224
File Explorer 227
Setting Oscilloscope Preferences 229
Setting the Oscilloscope's Clock 232
Setting the Rear Panel TRIG OUT Source 232
Performing Service Tasks 233
Configuring the [Quick Action] Key 238
This chapter explains oscilloscope utility functions.
I/O Interface Settings

The oscilloscope can be accessed and/or controlled remotely via these I/O
interfaces:
• USB device port on the rear panel (square shaped USB port).
• LAN interface when a LAN/VGA module is installed in the rear panel
module slot.
• GPIB interface when a GPIB module is installed in the rear panel
module slot.
To configure the I/O interfaces:
1 On the oscilloscope's front panel, press [Utility].
2 In the Utility Menu, press I/O.
3 In the I/O Menu, press Configure.
223
18 Utility Settings
• LAN — When a DSOXLAN LAN/VGA module is installed, you can use

the LAN Settings and LAN Reset softkeys to configure the LAN
interface. See "Setting up the Oscilloscope's LAN Connection" on
page 224.
• GPIB — When a DSOXGPIB GPIB module is installed, you can use the
Address softkey to configure the GPIB address.
• There are no configuration settings for the USB interface.
When an I/O interface is installed, remote control over that interface is
always enabled. Also, the oscilloscope can be controlled via multiple I/O
interfaces (for example, USB and LAN) at the same time.
See Also • Chapter 19, “Web Interface,” starting on page 241 (when the
oscilloscope is connected to a LAN).
• "Remote Programming via the Web Interface" on page 246
• The oscilloscope's Programmer's Guide.
• "Remote Programming with Agilent IO Libraries" on page 247
Setting up the Oscilloscope's LAN Connection

When the DSOXLAN LAN/VGA module is installed, you can place the
oscilloscope on the network and set up its LAN connection. Once that is
done, you can use the oscilloscope's web interface or remotely control the
oscilloscope via the LAN interface.
The oscilloscope supports methods for automated LAN configuration or
manual LAN configuration (see "To establish a LAN connection" on
page 225). It is also possible to set up a point- to- point LAN connection
between a PC and the oscilloscope (see "Stand- alone (Point- to- Point)
Connection to a PC" on page 226).
Once the oscilloscope is set up on the network, you can use the
oscilloscope's web page to view or change its network configuration and
access additional settings (like the network password). See Chapter 19,
“Web Interface,” starting on page 241.
When you connect the oscilloscope to a LAN it is a good practice to limit access to the
NOTE oscilloscope by setting a password. By default, the oscilloscope is not password protected.
See "Setting a Password" on page 252 to set a password.

Utility Settings 18
Any time you modify the oscilloscope's hostname, it breaks the connection between the
NOTE oscilloscope and the LAN. You need to re-establish communication to the oscilloscope
using the new hostname.
To establish a LAN connection

Automatic 1 Press [Utility] > I/O.
Configuration 2 Press the LAN Settings softkey.
3 Press the Config softkey; then, turn the Entry knob to select Automatic,
and press the softkey again to enable it.
If your network supports DHCP or AutoIP, enabling Automatic lets the
oscilloscope use those services to get its LAN configuration settings
4 If your network provides Dynamic DNS, you can enable the Dynamic DNS
option to let the oscilloscope register its hostname and use the DNS
server for name resolution.
5 You can enable the Multicast DNS option to let the oscilloscope use
Multicast DNS for name resolution on small networks without a
conventional DNS server.
6 Connect the oscilloscope to the local area network (LAN) by inserting
the LAN cable into the "LAN" port on the rear panel of the
oscilloscope.
In a few moments the oscilloscope will connect to the network
automatically.
If the oscilloscope does not automatically connect to the network, press
[Utility] > I/O > LAN Reset. In a few moments the oscilloscope will connect
to the network.
Manual 1 Get the oscilloscope's network parameters (host name, IP address,
Configuration subnet mask, gateway IP, DNS IP, etc.) from your network
administrator.
2 Press [Utility] > I/O.
3 Press the LAN Settings softkey.
and press the softkey again to disable it.

18 Utility Settings
If Automatic is not enabled, the oscilloscope's LAN configuration must

be set up manually using the Addresses and Host name softkeys
5 Configure the oscilloscope's LAN interface:
a Press the Addresses softkey.
b Use the Modify softkey (and the other softkeys and the Entry knob)
to enter the IP Address, Subnet Mask, Gateway IP, and DNS IP
values. When you are done, go back up in the menu hierarchy.
c Press the Host name softkey. Use the softkeys and the Entry knob to
enter the Host name. When you are done, go back up in the menu
hierarchy.
d Press the Apply softkey.
6 Connect the oscilloscope to the local area network (LAN) by inserting
the LAN cable into the "LAN" port on the rear panel of the
oscilloscope.
Stand-alone (Point-to-Point) Connection to a PC

The following procedure describes how to establish a point- to- point (stand
alone) connection to the oscilloscope. This is useful if you want to control
the oscilloscope using a laptop computer or a stand- alone computer.
1 Press [Utility] > I/O.
2 Press the LAN Settings softkey.
and press the softkey again to enable it.
If your network supports DHCP or AutoIP, enabling Automatic lets the
oscilloscope use those services to get its LAN configuration settings
4 Connect your PC to the oscilloscope using a cross- over LAN cable such
as Agilent part number 5061- 0701, available on the web at
"www.parts.agilent.com".
5 Cycle power on the oscilloscope. Wait until the LAN connection is
configured:
• Press [Utility] > I/O and wait until the LAN status shows "configured".
This may take a few minutes.
Now, the instrument is connected, and the instrument's web interface or
remote control via LAN may be used.

Utility Settings 18
File Explorer
The File Explorer lets you navigate the oscilloscope's internal file system
and the file systems of connected USB storage devices.
From the internal file system, you can load oscilloscope setup files or
mask files.
From a connected USB storage device, you can load setup files, mask files,
license files, firmware update (*.cab) files, label files, etc. Also, you can
delete files on a connected USB storage device.
The USB port on the front panel, and the USB port on the rear panel labeled "HOST" are
NOTE USB Series A receptacles. These are the receptacles to which you can connect USB mass
storage devices and printers.
The square receptacle on the rear panel labeled "DEVICE" is provided for controlling the
oscilloscope over USB. See the Programmer's Guide for more information.
The oscilloscope's internal file system, under "\Agilent Flash", consists of

10 locations for oscilloscope setup files, and four locations for mask files.
To use the File Explorer:
1 Press [Utility] > File Explorer.
2 In the File Explorer Menu, press the softkey in the first position and
use the Entry knob to navigate.

18 Utility Settings
The softkey in the first position can have these labels:

• Press to go — when you can push the Entry knob to navigate to a new
folder or storage location.
• Location — when pointing to a directory that is currently selected.
• Selected — when pointing to a file that can be loaded or deleted.
When this label appears, you can press the Load File or Delete File
softkeys to take the action.
Pushing the Entry knob is the same as pressing the Load File softkey.
A file that has been deleted from a USB storage device cannot be
recovered by the oscilloscope.
Use your PC to create directories on a USB storage device.
USB Storage Most USB mass storage devices are compatible with the oscilloscope.
Devices However, certain devices may be incompatible, and may not be able to be
read or written to.
When the USB mass storage device is connected to the oscilloscope's front
or rear USB host port, a small four- color circle icon may be displayed
briefly as the USB device is read.

Utility Settings 18
You do not need to "eject" the USB mass storage device before removing it.
Simply ensure that any file operation you've initiated is done, and remove
the USB drive from the oscilloscope's host port.
Do not connect USB devices that identify themselves as hardware type
"CD" because these devices are not compatible with the InfiniiVision
X- Series oscilloscopes.
If two USB mass storage devices are connected to the oscilloscope, the
first one is designated "\usb" and the second one is designated "\usb2".
See Also • Chapter 16, “Save/Recall (Setups, Screens, Data),” starting on page 205
Setting Oscilloscope Preferences

The User Preferences Menu (under [Utility] > Options > Preferences) lets you
specify oscilloscope preferences.
• "To choose "expand about" center or ground" on page 229
• "To disable/enable transparent backgrounds" on page 230
• "To load the default label library" on page 230
• "To set up the screen saver" on page 230
• "To set AutoScale preferences" on page 231
To choose "expand about" center or ground

When you change a channel's volts/division setting, the waveform display
can be set to expand (or compress) about the signal ground level or the
center of the display.
To set the waveform expansion reference point:
1 Press [Utility] > Options > Preferences > Expand and select:
• Ground— The displayed waveform will expand about the position of
the channel's ground. This is the default setting.
The ground level of the signal is identified by the position of the
ground level ( ) icon at the far- left side of the display.
The ground level will not move when you adjust the vertical
sensitivity (volts/division) control.

18 Utility Settings
If the ground level is off screen, the waveform will expand about the
top or bottom edge of the screen based on where the ground is off
screen.
• Center— The displayed waveform will expand about the center of the
display.
To disable/enable transparent backgrounds

There is a preference setting for whether measurements, statistics,
reference waveform information, and other text displays have transparent
or solid backgrounds.
1 Press [Utility] > Options > Preferences.
2 Press Transparent to toggle between transparent and solid text display
backgrounds.
To load the default label library

See "To reset the label library to the factory default" on page 109.
To set up the screen saver

The oscilloscope can be configured to turn on a display screen saver when
the oscilloscope has been idle for a specified length of time.
1 Press [Utility] > Options > Preferences > Screen Saver to display the Screen
Saver Menu.
2 Press the Saver softkey to select the screen saver type.

The screen saver can be set to Off, to display any of the images shown
in the list, or can display a user- defined text string.
If User is selected, press the Spell softkey to select the first character of
the text string. Use the Entry knob to choose a character. Then press
the Enter softkey to advance to the next character and repeat the
process. The resultant string is displayed in the "Text =" line above the
softkeys.

Utility Settings 18
3 Press the Wait softkey; then, turn the Entry knob to select the number
of minutes to wait before the selected screen saver activates.
When you turn the Entry knob, the number of minutes is displayed on
the Wait softkey. The default time is 180 minutes (3 hours).
4 Press the Preview softkey to preview the screen saver you have selected
with the Saver softkey.
5 To view the normal display after the screen saver has started, press any
key or turn any knob.
To set AutoScale preferences

1 Press [Utility] > Options > Preferences > AutoScale.
2 In the AutoScale Preferences Menu, you can:
• Press the Fast Debug softkey enable/disable this type of autoscale.
When fast debug is enabled, autoscale lets you make quick visual
comparisons to determine whether the signal being probed is a DC
voltage, ground, or an active AC signal.
Channel coupling is maintained to allow easy viewing of oscillating
signals.
• Press the Channels softkey and turn the Entry knob to specify the
channels to be autoscaled:
• All Channels — The next time you press [AutoScale], all channels that
meet the requirements of AutoScale will be displayed.
• Only Displayed Channels — The next time you press [AutoScale], only
the channels that are turned on will be examined for signal
activity. This is useful if you only want to view specific active
channels after pressing [AutoScale].
• Press the Acq Mode softkey and turn the Entry knob to select whether
the acquisition mode should be preserved during autoscale:
• Normal — to make the oscilloscope switch to Normal acquisition
mode whenever the [AutoScale] key is pressed. This is the default
mode.

18 Utility Settings
• Preserve — to make the oscilloscope remain in the acquisition mode

you have chosen when the [AutoScale] key is pressed.
Setting the Oscilloscope's Clock

The Clock Menu lets you set the current date and time of day (24- hour
format). This time/date stamp will appear on hardcopy prints and
directory information on the USB mass storage device.
To set the date and time, or to view the current date and time:
1 Press [Utility] > Options > Clock.
2 Press the Year, Month, Day, Hour or Minute softkey; then, rotate the Entry
knob to set to the desired number.
The hours are shown in the 24- hour format. So 1:00 PM is hour 13.
The real- time clock only allows selection of valid dates. If a day is
selected and the month or year is changed so the day is invalid, the day
is automatically adjusted.
Setting the Rear Panel TRIG OUT Source

You can choose the source of the TRIG OUT connector on the rear panel
of the oscilloscope:
1 Press [Utility] > Options > Rear Panel.
2 In the Rear Panel Menu, press Trig Out; then, turn the Entry knob to
select from:
• Triggers— Each time the oscilloscope triggers, a rising edge occurs on
TRIG OUT. The rising edge is delayed 30 ns from the oscilloscope's
trigger point. The output level is 0- 5 V into an open circuit, and
0- 2.5 V into 50 Ω. See Chapter 9, “Triggers,” starting on page 111.

Utility Settings 18
• Mask— The pass/fail status is evaluated periodically. When the

evaluation of the testing period results in a failure, the trigger output
pulses high (+5 V). Otherwise, the trigger output remains at low
(0 V). See Chapter 14, “Mask Testing,” starting on page 187.
• Waveform Generator Sync Pulse— All of the waveform generator output
functions (except DC and Noise) have an associated Sync signal:
The Sync signal is a TTL positive pulse that occurs when the
waveform rises above zero volts (or the DC offset value).
See Chapter 15, “Waveform Generator,” starting on page 199.
The TRIG OUT connector also provides the User Cal signal. See "To
perform user calibration" on page 234.
Performing Service Tasks

The Service Menu (under [Utility] > Service) lets you perform service- related
tasks:
• "To perform user calibration" on page 234

• "To perform hardware self test" on page 236
• "To perform front panel self test" on page 236
• "To display oscilloscope information" on page 236
• "To display the user calibration status" on page 237
For other information related to oscilloscope maintenance and service, see:
• "To clean the oscilloscope" on page 237
• "To check warranty and extended services status" on page 237
• "To contact Agilent" on page 237
• "To return the instrument" on page 237

18 Utility Settings
To perform user calibration

Perform user- calibration:
• Every two years or after 4000 hours of operation.
• If the ambient temperature is >10° C from the calibration temperature.
• If you want to maximize the measurement accuracy.
The amount of use, environmental conditions, and experience with other
instruments help determine if you need shorter User Cal intervals.
User Cal performs an internal self- alignment routine to optimize the signal
path in the oscilloscope. The routine uses internally generated signals to
optimize circuits that affect channel sensitivity, offset, and trigger
parameters.
Performing User Cal will invalidate your Certificate of Calibration. If NIST
(National Institute of Standards and Technology) traceability is required,
perform the "Performance Verification" procedure in the Agilent
InfiniiVision 2000/3000 X- Series Oscilloscopes Service Guide using
traceable sources.
To perform user calibration:
1 Disconnect all inputs from the front and rear panels, including the
digital channels cable on an MSO, and allow the oscilloscope to warm
up before performing this procedure.
2 Press the rear- panel CAL button to disable calibration protection.
3 Connect short (12 inch maximum) equal length cables to each analog
channel's BNC connector on the front of the oscilloscope. You will need
two equal- length cables for a 2- channel oscilloscope or four
equal- length cables for a 4- channel oscilloscope.
Use 50W RG58AU or equivalent BNC cables when performing User Cal.
For a 2- channel oscilloscope, connect a BNC tee to the equal length
cables. Then connect a BNC(f)- to- BNC(f) (also called a barrel
connector) to the tee as shown below.

Utility Settings 18
Long cable
to TRIG OUT
To Channel 1
To Channel 2
Figure 36 User Calibration cable for 2-channel oscilloscope
For a 4- channel oscilloscope, connect BNC tees to the equal- length

cables as shown below. Then connect a BNC(f)- to- BNC(f) (barrel
connector) to the tee as shown below.
To Channel 1
To Channel 2
To Channel 3
Longer cable
to TRIG OUT
To Channel 4
Figure 37 User Calibration cable for 4-channel oscilloscope

18 Utility Settings
4 Connect a BNC cable (40 inches maximum) from the TRIG OUT
connector on the rear panel to the BNC barrel connector.
5 Press the [Utility] key; then, press the Service softkey.
6 Begin the Self Cal by pressing the Start User Cal softkey.
To perform hardware self test

Pressing [Utility] > Service > Hardware Self Test performs a series of internal
procedures to verify that the oscilloscope is operating properly.
It is recommended you run Hardware Self Test:
• After experiencing abnormal operation.
• For additional information to better describe an oscilloscope failure.
• To verify proper operation after the oscilloscope has been repaired.
Successfully passing Hardware Self Test does not guarantee 100% of the
oscilloscope's functionality. Hardware Self Test is designed to provide an
80% confidence level that the oscilloscope is operating properly.
To perform front panel self test

Pressing [Utility] > Service > Front Panel Self Test lets you test the front panel
keys and knobs as well as the oscilloscope display.
Follow the on- screen instructions.
To display oscilloscope information

Press [Help] > About Oscilloscope to display information about your
oscilloscope:
• Model number.
• Serial number.
• Bandwidth.
• Module installed.
• Software version.
• Installed licenses. See also "Loading Licenses and Displaying License
Information" on page 261.

Utility Settings 18
To display the user calibration status

Pressing [Utility] > Service > User Cal Status displays the summary results of
the previous User Cal, and the status of probe calibrations for probes that
can be calibrated. Note that passive probes do not need to be calibrated.
Results:
User Cal date:
Change in temperature since last User Cal:
Failure:
Comments:
Probe Cal Status:
To clean the oscilloscope

1 Remove power from the instrument.
2 Clean the external surfaces of the oscilloscope with a soft cloth
dampened with a mixture of mild detergent and water.
3 Make sure that the instrument is completely dry before reconnecting it
to a power source.
To check warranty and extended services status

To learn the warranty status of your oscilloscope:
1 Point your web browser to: "www.agilent.com/find/warrantystatus"
2 Enter your product's model number and serial number. The system will
search for the warranty status of your product and display the results.
If the system cannot find your product's warranty status, select Contact
Us and speak with an Agilent Technologies representative.
To contact Agilent
Information on contacting Agilent Technologies can be found at:
"www.agilent.com/find/contactus"
To return the instrument

Before shipping the oscilloscope to Agilent Technologies, contact your
nearest Agilent Technologies sales or service office for additional details.
Information on contacting Agilent Technologies can be found at:
"www.agilent.com/find/contactus"

18 Utility Settings
1 Write the following information on a tag and attach it to the

oscilloscope.
• Name and address of owner.
• Model number.
• Serial number.
• Description of service required or failure indication.
2 Remove accessories from the oscilloscope.
Only return accessories to Agilent Technologies if they are associated
with the failure symptoms.
3 Package the oscilloscope.
You can use the original shipping container, or provide your own
materials sufficient to protect the instrument during shipping.
4 Seal the shipping container securely, and mark it FRAGILE.
Configuring the [Quick Action] Key

The [Quick Action] key lets you perform common, repetitive actions by
pressing a single key.
To configure the [Quick Action] key:
1 Press [Utility] > Quick Action > Action; then, select the action that should be
performed:
• Off — disables the [Quick Action] key.
• Quick Measure All — displays a popup containing a snapshot of all the
single waveform measurements. The Source softkey lets you select the
waveform source (which also becomes the source selection in the
Measurement Menu). See Chapter 13, “Measurements,” starting on
page 167.
• Quick Print — prints the current screen image. Press Settings to set up
the printing options. See Chapter 17, “Print (Screens),” starting on
page 219.
• Quick Save — saves the current image, waveform data, or setup. Press
Settings to set up the save options. See Chapter 16, “Save/Recall

Utility Settings 18
• Quick Recall — recalls a setup, mask, or reference waveform. Press

Settings to set up the recall options. See Chapter 16, “Save/Recall
• Quick Freeze Display — freezes the display without stopping running
acquisitions or un- freezes the display if currently frozen. For more
information, see "To freeze the display" on page 103.
• Quick Trigger Mode — toggles the trigger mode between Auto and
Normal, see "To select the Auto or Normal trigger mode" on
page 134.
• Quick Clear Display — clears the display, see "To clear the display" on
page 102.
Once the [Quick Action] key is configured, you simply press it to perform
the selected action.

18 Utility Settings

User's Guide
19
Web Interface
Accessing the Web Interface 242
Browser Web Control 243
Save/Recall 247
Get Image 249
Identification Function 250
Instrument Utilities 251
Setting a Password 252
When the Agilent InfiniiVision X- Series oscilloscopes have the DSOXLAN

LAN/VGA option module installed, you can access the oscilloscope's
built- in web server using a Java - enabled web browser. The oscilloscope's
web interface lets you:
• View information about the oscilloscope like its model number, serial
number, host name, IP address, and VISA (address) connect string.
• Control the oscilloscope using the Remote Front Panel.
• Send SCPI (Standard Commands for Programmable Instrumentation)
remote programming commands via the SCPI Commands applet window.
• Save setups, screen images, waveform data, and mask files.
• Recall setup files, reference waveform data files, or mask files.
• Get screen images and save or print them from the browser.
• Activate the Identification function to identify a particular instrument
by causing a message to be displayed or a front panel light to blink.
• View installed options, view firmware versions and install firmware
upgrade files, and view calibration status (via the Instrument Utilities
page).
• View and modify the oscilloscope's network configuration.
241
19 Web Interface
The web interface for InfiniiVision X- Series oscilloscopes also provides

help for each of its pages.
Microsoft Internet Explorer is the recommended Web browser for
communication and control of the oscilloscope. Other Web browsers may
work but are not guaranteed to work with the oscilloscope. The Web
browser must be Java- enabled with Sun Microsystems Java Plug- in.
Before you can use the web interface, you must place the oscilloscope on
the network and set up its LAN connection.
Accessing the Web Interface

To access the oscilloscope's web interface:
1 Connect the oscilloscope to your LAN (see "To establish a LAN
connection" on page 225) or establish a point- to- point connection (see
"Stand- alone (Point- to- Point) Connection to a PC" on page 226).
It is possible to use a point- to- point connection, but using a normal
LAN connection is the preferred method.
2 Type the oscilloscope's hostname or IP address in the web browser.
The oscilloscope's web interface Welcome Page is displayed.

Web Interface 19
Browser Web Control

The web interface's Browser Web Control page gives you access to:
• The Real Scope Remote Front Panel (see "Real Scope Remote Front
Panel" on page 244).
• The Simple Remote Front Panel (see "Simple Remote Front Panel" on
page 245).
• The SCPI Command window applet for Remote Programming (see
"Remote Programming via the Web Interface" on page 246).
If Java is not installed on your PC, you will be prompted to install the Sun Microsystems
NOTE Java Plug-in. This plug-in must be installed on the controlling PC for the web interface's
Remote Front Panel or Remote Programming operations.

19 Web Interface
The SCPI Command window is useful for testing commands or entering a

few commands interactively. When creating automated programs for
controlling the oscilloscope, you will typically use the Agilent IO Libraries
from within a programming environment like Microsoft Visual Studio (see
"Remote Programming with Agilent IO Libraries" on page 247).
Real Scope Remote Front Panel

To operate the oscilloscope using the web interface's Real Scope Remote
Front Panel:
1 Access the oscilloscope's web interface (see "Accessing the Web
Interface" on page 242).
2 When the oscilloscope's web interface is displayed, select
Browser Web Control, then select Real Scope Remote Front Panel. After a few
seconds the Remote Front Panel appears.
3 Click keys or knobs that you would normally press on the oscilloscope's
front panel. Drag on edges of knobs to turn them.

Web Interface 19
Simple Remote Front Panel

To operate the oscilloscope using the web interface's Simple Remote Front
Panel:
Browser Web Control, then select Simple Remote Front Panel. After a few
seconds the Remote Front Panel appears.
3 Use the Main Menu and the Function Keys to control the oscilloscope.
To view Quick Help, right- click on a softkey.
Main Menu
Function Keys
Hint appears
when you roll
over with
mouse
Softkeys
(left-click to
select, right-click
for Quick Help)
Scrolling and When using a monitor resolution of 800 x 600 or less on the remote
Monitor computer, you need to scroll to access the full remote front panel. To
Resolution display the remote front panel without scroll bars, use a monitor
resolution greater than 800 x 600 on your computer's display.

19 Web Interface
Remote Programming via the Web Interface

To send remote programming commands to the oscilloscope via the SCPI
Commands applet window:
Browser Web Control, then select Remote Programming.
The SCPI Commands applet appears within the browser web page.

Web Interface 19
Remote Programming with Agilent IO Libraries

While the SCPI Commands applet window lets you enter and remote
programming commands, remote programming for automated test and data
acquisition is typically done using the Agilent IO Libraries, which are
separate from the instrument's web interface.
The Agilent IO Libraries let a controller PC communicate with Agilent
InfiniiVision oscilloscopes via their USB, LAN (when the LAN/VGA option
module is installed), or GPIB (when the GPIB option module is installed)
interfaces.
The Agilent IO Libraries Suite connectivity software to enables
communication over these interfaces. You can download the Agilent IO
Libraries Suite from "www.agilent.com/find/iolib".
Information about controlling the oscilloscope through remote commands
is contained in the Programmer's Guide, which is included on the
documentation CD supplied with this oscilloscope. You can also access this
document on the Agilent web site.
For more information about connecting to the oscilloscope, refer to the
Agilent Technologies USB/LAN/GPIB Interfaces Connectivity Guide. For a
printable electronic copy of the Connectivity Guide, direct your Web
browser to "www.agilent.com" and search for "Connectivity Guide".
Save/Recall
You can save setup files, screen images, waveform data files, or mask files
to your PC via the oscilloscope's web interface (see "Saving Files via the
Web Interface" on page 247).
You can recall setup files, reference waveform data files, or mask files
from your PC via the oscilloscope's web interface (see "Recalling Files via
the Web Interface" on page 249).
Saving Files via the Web Interface

To save setup files, screen images, waveform data files, or mask files to
your PC via the oscilloscope's web interface:

19 Web Interface

2 When the oscilloscope's web interface is displayed, select the Save/Recall
tab from the left side of the Welcome screen.
3 Click the Save link.
4 On the Save page:
a Enter the name of the file you are saving to.
b Select the format.
You can click Preview to view the oscilloscope's current screen image.
When previewing, you can use the New Acquisition check box to force
a new acquisition before the preview.
With some formats, you can click Save Setup Info to save setup
information to an ASCII .txt format file.
c Click Save.
The current acquisition is saved.
d In the File Download dialog, click Save.
e In the Save As dialog, navigate to the folder where you want to save
the file; then, click Save.

Web Interface 19
Recalling Files via the Web Interface

To recall setup files, reference waveform data files, or mask files from
your PC via the oscilloscope's web interface:
2 When the oscilloscope's web interface is displayed, select the Save/Recall
tab from the left side of the Welcome screen.
3 Click the Recall link.
4 On the Recall page:
a Click Browse....
b In the "Choose file" dialog, select the file you want to recall; then,
click Open.
c When recalling reference waveform data files, select the To Reference
Waveform location.
d Click Recall.
Get Image
To save (or print) the oscilloscope's display from the web interface:

19 Web Interface
2 When the oscilloscope's web interface is displayed, select the Get Image
tab from the left side of the Welcome screen. After a delay of several
seconds, the oscilloscope's screen image will be displayed.
3 Right- click on the image and select Save Picture As... (or Print Picture...).
4 Select a storage location for the image file and click Save.
Identification Function
The Identification web interface feature is useful when trying to locate a
specific instrument in a rack of equipment.
2 When the oscilloscope's web interface Welcome Page is displayed, select
the Identification on radio button.
An "Identify" message is displayed on the oscilloscope; you can either
select Identification off or press the OK softkey on the oscilloscope to
continue.

Web Interface 19
Identification option
Instrument Utilities
The Instrument Utilities page of the web interface lets you:
• View installed options.
• View firmware versions.
• Install firmware upgrade files.
• View calibration status.
You can select these cababilities via a drop- down menu.

19 Web Interface
Setting a Password
Whenever you connect the oscilloscope to a LAN, it is good practice to set
a password. The password prevents someone from remotely accessing the
oscilloscope via a Web browser and changing parameters. Remote users
can still view the Welcome screen, view network status, etc., but they can't
operate the instrument or change its setup without the password.
To set a password:
2 When the oscilloscope's web interface is displayed, select the Configure
Network tab from the instrument's Welcome page.

Web Interface 19
3 Click the Modify Configuration button.
Modify Configuration
Configure
Network
tab
4 Enter your desired password, and click Apply Changes.

19 Web Interface
Enter
password
When accessing the password protected oscilloscope, the user name is the
IP address of the oscilloscope.
To reset the Do one of these things to reset the password:
password • Using the keys on the front panel of the oscilloscope, press [Utility] > I/O
> LAN Reset.
• Using the web browser select the Configure Network tab, select Modify
Configuration, erase the Password, and select Apply Changes.

User's Guide
20
Reference
Specifications and Characteristics 255
Measurement Category 255
Environmental Conditions 257
Probes and Accessories 258
Loading Licenses and Displaying License Information 261
Software and Firmware Updates 262
Binary Data (.bin) Format 262
CSV and ASCII XY files 269
Acknowledgements 271
Specifications and Characteristics

Please see the InfiniiVision oscilloscope data sheets for complete,
up- to- date specifications and characteristics. To download a data sheet,
please visit: "www.agilent.com/find/2000X- Series"
Then, select the Library tab, followed by Specifications.
Or, go to the Agilent home page at "www.agilent.com" and search for "2000
X- Series oscilloscopes data sheet".
To order a data sheet by phone, please contact your local Agilent office.
The complete list is available at: "www.agilent.com/find/contactus" or on
"To contact Agilent" on page 237.
Measurement Category
• "Oscilloscope Measurement Category" on page 256
• "Measurement Category Definitions" on page 256
255
20 Reference
• "Transient Withstand Capability" on page 257
Oscilloscope Measurement Category

The InfiniiVision oscilloscopes are intended to be used for measurements
in Measurement Category I.
Use this instrument only for measurements within its specified measurement
WARNIN G
category.
Measurement Category Definitions

Measurement category I is for measurements performed on circuits not
directly connected to MAINS. Examples are measurements on circuits not
derived from MAINS, and specially protected (internal) MAINS derived
circuits. In the latter case, transient stresses are variable; for that reason,
the transient withstand capability of the equipment is made known to the
user.
Measurement category II is for measurements performed on circuits
directly connected to the low voltage installation. Examples are
measurements on household appliances, portable tools and similar
equipment.
Measurement category III is for measurements performed in the building
installation. Examples are measurements on distribution boards,
circuit- breakers, wiring, including cables, bus- bars, junction boxes,
switches, socket- outlets in the fixed installation, and equipment for
industrial use and some other equipment, for example, stationary motors
with permanent connection to the fixed installation.
Measurement category IV is for measurements performed at the source of
the low- voltage installation. Examples are electricity meters and
measurements on primary overcurrent protection devices and ripple
control units.

Reference 20
Transient Withstand Capability
Maximum input voltage at analog inputs

CAUTION
With 10073C 10:1 probe: CAT I 500 Vpk, CAT II 400 Vpk
With N2862A or N2863A 10:1 probe: 300 Vrms
Maximum input voltage at digital channels

CAUTION
±40 V peak CAT I; transient overvoltage 800 Vpk
Environmental Conditions
Environment Indoor use only.

Ambient Operating 0 °C to +55 °C; non-operating –40 °C to +71 °C
temperature
Humidity Operating: Up to 80% RH at or below +40 °C. Up to 45% RH up to +50 °C.

Non-operating: Up to 95% RH up to +40 °C. Up to 45% RH up to +50 °C.
Altitude Operating and non-operating to 4,000 m (13,123 ft)

Overvoltage This product is intended to be powered by MAINS that comply to Overvoltage
Category Category II, which is typical of cord-and-plug connected equipment.
Pollution Degree The InfiniiVision 2000/3000 X-Series oscilloscopes may be operated in
environments of Pollution Degree 2 (or Pollution Degree 1).
Pollution Degree Pollution Degree 1: No pollution or only dry, non-conductive pollution occurs.
Definitions The pollution has no influence. Example: A clean room or climate controlled
office environment.
Pollution Degree 2. Normally only dry non-conductive pollution occurs.
Occasionally a temporary conductivity caused by condensation may occur.
Example: General indoor environment.
Pollution Degree 3: Conductive pollution occurs, or dry, non-conductive
pollution occurs which becomes conductive due to condensation which is
expected. Example: Sheltered outdoor environment.

20 Reference
Probes and Accessories

This setion lists the probes and accessories that are compatible with the
2000 X- Series oscilloscopes.
• "Passive Probes" on page 258
• "Differential Probes" on page 259
• "Current Probes" on page 259
• "Accessories Available" on page 260
Because the 2000 X- Series oscilloscopes do not have a ring around the
BNC connector for identifying probes, you must set the probe attenuation
factor manually. See "To specify the probe attenuation" on page 60.
See Also For more information on probes and accessories, see "www.agilent.com"
for:
• "Probes and Accessories Selection Guide (5989- 6162EN)"
• "5000, 6000, and 7000 Series InfiniiVision Oscilloscope Probes and
Accessories Data Sheet (5968- 8153EN)"
Passive Probes
Passive probes are included with the 2000 X- Series oscilloscopes for each
analog channel.
The following passive probes can be used with the InfiniiVision
2000 X- Series oscilloscopes. Any combination of passive probes can be
used.
Table 6 Passive Probes
Model Description
1165A Passive probe, 10:1, 600 MHz, 1.5 m
10070C/D Passive probe, 1:1 20 MHz, 1.5 m

10073C Passive probe, 10:1, 500 MHz, 1.5 m
10074C Passive probe, 10:1, 150 MHz, 1.5 m
10076A/B Passive probe, 100:1, 4 kV, 250 MHz

Reference 20
Table 6 Passive Probes (continued)
Model Description
N2771A/B Passive probe, 1000:1, 30 kV, 50 MHz
N2862A/B Passive probe, 10:1, 150 MHz, 1.2 m
N2863A/B Passive probe, 10:1, 300 MHz, 1.2 m

N2889A Passive probe, 10:1/1:1, 350 MHz, 1.2 m
N2890A Passive probe, 10:1, 500 MHz, 1.2 m
Differential Probes
The following differential probes can be used with the InfiniiVision
Table 7 Differential Probes
Model Description
1141A Active differential probe, 200 MHz, 200 VDC + peak AC max (requires
1142A power supply)
1144A Active probe, 800 MHz (requires 1142A power supply)
1145A Active probe, 750 MHz 2-ch (requires 1142A power supply)
N2772A Active differential probe, 20 MHz, 1.2 kVDC + peak AC max (requires
N2773A power supply)
N2791A High-voltage differential probe, 25 MHz, +/-700 V, 1 MOhm termination,

10:1 or 100:1 (switchable)
N2792A Differential probe, 200 MHz 10:1, 50 Ohm termination
N2793A Differential probe, 800 MHz 10:1, +/-15 V, 50 Ohm termination
Current Probes
The following current probes can be used with the InfiniiVision

20 Reference
Table 8 Current Probes
Model Description
1146A Current probe, 100 kHz, 100 A, AC/DC

N2774A (Obsolete, replaced by N2782A) with N2775A power supply
N2780A Current probe, 2 MHz, 500 A, AC/DC (use with N2779A power supply)
Accessories Available
In addition to passive proves ("Passive Probes" on page 258), differential
probes ("Differential Probes" on page 259), and current probes ("Current
Probes" on page 259), the following accessories are available for the
InfiniiVision 2000 X- Series oscilloscopes.
Table 9 Accessories Available for InfiniiVision 2000 X-Series Oscilloscopes
Model/Part # Description
DSOXLAN LAN/VGA connection module

DSOXGPIB GPIB connection module
N6456A Rack mount kit

N6457A Soft carrying case and front panel cover
N2786A 2-leg probe positioner
N2787A 3D probe positioner
1180CZ Testmobile
N6458A Hardcopy user's guide

various Front panel overlays - see "Front Panel Overlays for Different Languages" on
page 35.
N6459-60001 8-channel logic probe and accessory kit (standard with MSO models and with
DSOX2MSO upgrade)

Reference 20
You can find these items at "www.agilent.com" or at

"www.parts.agilent.com".
Loading Licenses and Displaying License Information

• "Licensed Options Available" on page 261
• "Other Options Available" on page 262
• "Upgrading to an MSO" on page 262
Licensed Options Available

Many of the following licensed options can be easily installed without
returning the oscilloscope to a Service Center. Not all options can be
installed on all models. See data sheets for details.
Table 10 Licensed Options Available
License Description After purchase model number, notes

EDK Educator's Kit Order DSOXEDK.
Provides training signals on the oscilloscope's Demo
terminals and a lab guide/tutorial for education
environments.
MASK Mask Limit Test Order DSOX2MASK.

Lets you create a mask and test waveforms to determine
whether they comply to the mask.
MSO Mixed Signal Oscilloscope (MSO). Upgrade a DSO to an Order DSOX2MSO.
MSO. The digital probe cable kit is supplied with
Adds 8 digital channels. You do not have to install any the MSO license.
hardware.
SGM Segmented Memory. Order DSOX2SGM.
Lets you capture infrequent or burst signals with great
resolution by eliminating the capture of your signal's
"inactivity".
WAVEGEN Waveform Generator. Order DSOX2WAVEGEN.

20 Reference
Other Options Available
Table 11 Calibration Option
Option Order
A6J ANSI Z540 Compliant Calibration
Upgrading to an MSO
A license can be installed to activate the digital channels of an
oscilloscope that was not originally ordered as a mixed- signal oscilloscope
(MSO). A mixed signal oscilloscope has analog channels plus 8
time- correlated digital timing channels.
For information about upgrading your oscilloscope through licensing,
contact your local Agilent Technologies representative or see
"www.agilent.com/find/2000X- Series".
Software and Firmware Updates

From time to time Agilent Technologies releases software and firmware
updates for its products. To search for firmware updates for your
oscilloscope, direct your web browser to
"www.agilent.com/find/2000X- Series- sw".
To view the currently installed software and firmware press [Help] > About
Oscilloscope.
Once you have downloaded a firmware update file, you can place it on a
USB storage device and load the file using File Explorer (see "File
Explorer" on page 227), or you can use the Instrument Utilities page of
the oscilloscope's web interface (see "Instrument Utilities" on page 251).
Binary Data (.bin) Format

The binary data format stores waveform data in binary format and
provides data headers that describe that data.

Reference 20
Because the data is in binary format, the size of the file is approximately
5 times smaller than the ASCII XY format.
If more than one source is on, all displayed sources will be saved, except
math functions.
When using segmented memory, each segment is treated as a separate
waveform. All segments for a channel are saved, then all segments of the
next (higher numbered) channel are saved. This continues until all
displayed channels are saved.
When the oscilloscope is in the Peak Detect acquisition mode, the
minimum and maximum value waveform data points are saved to the file
in separate waveform buffers. The minimum value data points are saved
first; then, the maximum value data points are saved.
BIN data - using When saving all segments, each segment has its own waveform header (see
segmented "Binary Header Format" on page 264).
memory
In BIN file format, data are presented as follows:
• Channel 1 data (all segments)
• Digital channel data (all segments)
• Math waveform data (all segments)
When not saving all segments, the number of waveforms is equivalent to
the number of active channels (including math and digital channels, with
up to seven waveforms for each digital pod). When saving all segments,
the number of waveforms is equal to the number of active channels
multiplied by the number of segments acquired.
Binary Data in MATLAB

Binary data from an InfiniiVision oscilloscope can be imported to The
MathWorks MATLAB®. You can download the appropriate MATLAB
functions from the Agilent Technologies web site at
"www.agilent.com/find/2000X- Series- sw".
Agilent provides the .m files, which need to be copied into the work
directory for MATLAB. The default work directory is C:\MATLAB7\work.

20 Reference
Binary Header Format

File Header There is only one file header in a binary file. The file header consists of
the following information.
Cookie Two byte characters, AG, that indicate the file is in the Agilent Binary Data file
format.
Version Two bytes that represent the file version.
File Size A 32-bit integer that is the number of bytes that are in the file.
Number of A 32-bit integer that is the number of waveforms that are stored in the file.
Waveforms
Waveform Header It is possible to store more than one waveform in the file, and each
waveform stored will have a waveform header. When using segmented
memory, each segment is treated as a separate waveform. The waveform
header contains information about the type of waveform data that is
stored following the waveform data header.
Header Size A 32-bit integer that is the number of bytes in the header.
Waveform Type A 32-bit integer that is the type of waveform stored in the file:
• 0 = Unknown.
• 1 = Normal.
• 2 = Peak Detect.
• 3 = Average.
• 4 = Not used in InfiniiVision oscilloscopes.
• 6 = Logic.
Number of A 32-bit integer that is the number of waveform buffers required to read the
Waveform data.
Buffers
Points A 32-bit integer that is the number of waveform points in the data.
Count A 32-bit integer that is the number of hits at each time bucket in the waveform
record when the waveform was created using an acquisition mode like
averaging. For example, when averaging, a count of four would mean every
waveform data point in the waveform record has been averaged at least four
times. The default value is 0.

Reference 20
X Display Range A 32-bit float that is the X-axis duration of the waveform that is displayed. For
time domain waveforms, it is the duration of time across the display. If the
value is zero then no data has been acquired.
X Display Origin A 64-bit double that is the X-axis value at the left edge of the display. For time
domain waveforms, it is the time at the start of the display. This value is
treated as a double precision 64-bit floating point number. If the value is zero
then no data has been acquired.
X Increment A 64-bit double that is the duration between data points on the X axis. For
time domain waveforms, this is the time between points. If the value is zero
then no data has been acquired.
X Origin A 64-bit double that is the X-axis value of the first data point in the data
record. For time domain waveforms, it is the time of the first point. This value
is treated as a double precision 64-bit floating point number. If the value is
zero then no data has been acquired.
X Units A 32-bit integer that identifies the unit of measure for X values in the acquired
data:
• 0 = Unknown.
• 1 = Volts.
• 2 = Seconds.
• 3 = Constant.
• 4 = Amps.
• 5 = dB.
• 6 = Hz.
Y Units A 32-bit integer that identifies the unit of measure for Y values in the acquired
data. The possible values are listed above under X Units.
Date A 16-byte character array, left blank in InfiniiVision oscilloscopes.
Time A 16-byte character array, left blank in the InfiniiVision oscilloscopes.

Frame A 24 byte character array that is the model number and serial number of the
oscilloscope in the format of: MODEL#:SERIAL#.
Waveform Label A 16 byte character array that contains the label assigned to the waveform.
Time Tags A 64-bit double, only used when saving multiple segments (requires
segmented memory option). This is the time (in seconds) since the first
trigger.
Segment Index A 32-bit unsigned integer. This is the segment number. Only used when saving
multiple segments.

20 Reference
Waveform Data A waveform may have more than one data set. Each waveform data set
Header will have a waveform data header. The waveform data header consists of
information about the waveform data set. This header is stored
immediately before the data set.
Waveform Data A 32-bit integer that is the size of the waveform data header.
Header Size
Buffer Type A 16-bit short that is the type of waveform data stored in the file:
• 0 = Unknown data.
• 1 = Normal 32-bit float data.
• 2 = Maximum float data.
• 3 = Minimum float data.
• 6 = Digital unsigned 8-bit char data (for digital channels).
Bytes Per Point A 16-bit short that is the number of bytes per data point.
Buffer Size A 32-bit integer that is the size of the buffer required to hold the data points.
Example Program for Reading Binary Data

To find an example program for reading binary data, direct your web
browser to "www.agilent.com/find/2000X- Series- sw", and select "Example
Program for Reading Binary Data".
Examples of Binary Files

Single The following picture shows a binary file of a single acquisition with
Acquisition multiple analog channels.
Multiple Analog
Channels

Reference 20
File Header
Number of Waveforms = N
12 bytes
Waveform Header 1 Number of Waveform Buffers = 1

140 bytes
Waveform Data
Buffer Type = 1 (floating point)
Header 1
Bytes per Point = 4
12 bytes
Voltage Data 1
buffer size

140 bytes
Waveform Data
Header 2
Bytes per Point = 4
12 bytes
Voltage Data 2
buffer size
Waveform Header N Number of Waveform Buffers = 1

140 bytes
Waveform Data
Header N
Bytes per Point = 4
12 bytes
Voltage Data N
buffer size
Single The following picture shows a binary file of a single acquisition with all
Acquisition All pods for the logic channels saved.
Pods Logic
Channels

20 Reference
File Header
Number of Waveforms = 2
12 bytes

140 bytes
Waveform Data
Buffer Type = 6 (unsigned char)
Header 1
Bytes per Point = 1
12 bytes
Pod 1 Timing Data

buffer size

140 bytes
Waveform Data
Buffer Type = 6 (unsigned char)
Header 2
Bytes per Point = 1
12 bytes
Pod 2 Timing Data

buffer size
Segmented The following picture shows a binary file of a segmented memory

Memory acquisition on one analog channel.
Acquisition on
One Analog
Channel

Reference 20
File Header
Number of Waveforms = N = Number of Segments
12 bytes
Number of Waveform Buffers = 1

Waveform Header 1
Index = 1
140 bytes
Time Tag = 0.0
Waveform Data
Header 1
Bytes per Point = 4
12 bytes
Voltage Data 1
buffer size

Waveform Header 2
Index = 2
140 bytes
Time Tag = time between segment 1 and 2
Waveform Data
Header 2
Bytes per Point = 4
12 bytes
Voltage Data 2
buffer size

Waveform Header N
Index = N
140 bytes
Time Tag = time between segment 1 and N
Waveform Data
Header N
Bytes per Point = 4
12 bytes
Voltage Data N
buffer size
CSV and ASCII XY files

• "CSV and ASCII XY file structure" on page 270

20 Reference
CSV and ASCII XY file structure

In CSV or ASCII XY format the Length control selects the number of points
per segment. All segments are contained in the CSV file or in each ASCII
XY data file.
For example: If the Length control is set to 1000 points, there will be 1000
points (rows in the spreadsheet) per segment. When saving all segments
there are three header rows, so the data for the first segment starts at
row 4. The second segment's data starts at row 1004. The time column
shows the time since the trigger on the first segment. The top row shows
the selected number of points per segment.
BIN files are a more efficient data transfer format than CSV or ASCII XY.
Use this file format for fastest data transfer.
Minimum and Maximum Values in CSV Files

If you are running a Minimum or Maximum measurement, the minimum
and maximum values shown in the measurement display may not appear
in the CSV file.
Explanation: When the oscilloscope's sample rate is 4 GSa/s, a sample will be taken
every 250 ps. If the horizontal scale is set to 10 us/div, there will be
100 us of data displayed (because there are ten divisions across the
screen). To find the total number of samples the oscilloscope will take:
100 us x 4 GSa/s = 400K samples
The oscilloscope is required to display those 400K samples using 640 pixel
columns. The oscilloscope will decimate the 400K samples to 640 pixel
columns, and this decimation keeps track of the min and max values of all
the points that are represented by any given column. Those min and max
values will be displayed in that screen column.
A similar process is used to reduce the acquired data to produce a record
usable for various analysis needs such as measurements and CSV data.
This analysis record (or measurement record) is much larger than 640
and may in fact contain up to 65536 points. Still, once the # of acquired
points > 65536, some form of decimation is required. The decimator used
to produce a CSV record is configured to provide a best- estimate of all
the samples that each point in the record represents. Therefore, the min
and max values may not appear in the CSV file.

Reference 20
Acknowledgements
RealVNC RealVNC is licensed under the GNU General Public License. Copyright (C)
2002- 2005 RealVNC Ltd. All Rights Reserved.
This is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free
Software Foundation; either version 2 of the License, or (at your option)
any later version.
This software is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details. The license is located on the
Agilent InfiniiVision Oscilloscopes Documentation CD- ROM.
RealVNC source code can be obtained from RealVNC or by contacting
Agilent. Agilent will charge for the cost of physically performing the
source distribution.
HDF5 Reference Waveform files use HDF5.
HDF5 was developed by "The HDF Group" and by the National Center for
Supercomputing Applications at the University of Illinois at
Urbana- Champaign.

20 Reference

Index
Symbols Auto Increment, 215 C
Auto Scale key, 32
(-) Width measurement, 181 Auto Setup, FFT, 69 calibration, 234
(+) Width measurement, 181 Auto trigger mode, 134 calibration protect button, 37, 38
Auto? trigger indicator, 135 calibration status, 251
A AutoIP, 225, 226 capture signal bursts, 153
automatic measurements, 167, 169 Center, FFT, 68
About Oscilloscope, 236 automatic setup, 83 channel labels, 105
AC channel coupling, 58 AutoScale preferences, 231 channel, analog, 55
AC RMS - Full Screen measurement, 177 AutoScale, digital channels, 83 channel, bandwidth limit, 58
AC RMS - N Cycles measurement, 177 AutoScale, undo, 26 channel, coupling, 57
accessories, 19, 258, 260 Average - Full Screen measurement, 176 channel, invert, 59
acquire, 141, 151 Average - N Cycles measurement, 176 channel, on/off keys, 34
Acquire key, 33 averaging acquire mode, 147, 151 channel, position, 57
acquisition memory, 112 channel, probe units, 60
acquisition memory, saving, 211 channel, skew, 61
acquisition mode, 147 B channel, vernier, 58
acquisition mode, averaging, 151 Back Up key, 29 channel, vertical sensitivity, 57
acquisition mode, high resolution, 153 bandwidth, 236 characteristics, 255
acquisition mode, normal, 148 bandwidth limit, 58 choosing values, 30
acquisition mode, peak detect, 148 bandwidth required, oscilloscope, 146 cleaning, 237
acquisition mode, preserve during bandwidth, oscilloscope, 144 clear display, 150
AutoScale, 231 Base measurement, 174 clear display, Quick Clear Display, 239
acquisition modes, 141 BIN file format, 206 clear persistence, 102
activity indicator, 85 binary data (.bin), 262 clock, 232
actual sample rate, 147 binary data file examples, 266 CMOS threshold, 87
adding digital channels license, 262 binary data in MATLAB, 263 compensate passive probes, 27, 34
addition math function, 66 binary data, example program for Config softkey, 225, 226
Addresses softkey, 226 reading, 266 connect probes, digital, 79
Agilent IO Libraries Suite, 247 Blackman Harris FFT window, 69 connection, to a PC, 226
aliasing, 143 blanking, 50 connectors, rear panel, 37
aliasing, FFT, 72 BMP file format, 206 control, remote, 223
alternating edge trigger, 115 brick-wall frequency response, 144 controls, front panel, 28
Amplitude measurement, 172 brightness of waveforms, 29 copyright, 2
analog channel, probe attenuation, 60 Browser Web Control, 243, 244, 245, 246 coupling, channel, 57
analog channel, setup, 55 built-in help, 40 coupling, trigger, 136
analog filters, adjusting, 67 burst width measurements, 181 crosstalk problems, 67
Analyze key, 30 burst, capture signal bursts, 153 CSV file format, 206
Analyze Segments, 154, 155 bus display mode, 88 CSV files, minimum and maximum
ASCII file format, 206 buttons (keys), front panel, 28 values, 270
attenuation, probe, 60 current probes, 259
attenuation, probe, external trigger, 139 cursor measurements, 157

Index
cursor units, 160 digital display, interpreting, 84 FFT measurements, 67

Cursors key, 33 digital probes, 79, 91 FFT resolution, 71
Cursors knob, 33 digital probes, impedance, 91 FFT spectral leakage, 74
cursors, binary, 159 Display key, 33 FFT units, 72
cursors, hex, 159 display multiple acquisitions, 142 FFT vertical units, 69
cursors, manual, 158 display, area, 39 FFT window, 68
cursors, track waveform, 159 display, interpreting, 38 file explorer, 227
display, persistence, 101 file format, ASCII, 206
D display, signal detail, 99 file format, BIN, 206
display, softkey labels, 40 file format, BMP, 206
D*, 32, 87 display, status line, 39 file format, CSV, 206
damage, shipping, 19 displayed channels AutoScale, 231 file format, PNG, 206
data sheet, 255 distortion problems, 67 File keys, 33
DC channel coupling, 58 DNS IP, 225 file name, new, 214
DC RMS - Full Screen measurement, 176 Duty cycle measurement, 181 file, save, recall, load, 227
DC RMS - N Cycles measurement, 177 Dynamic DNS, 225 fine adjustment, horizontal scale, 52
DC signals, checking, 135 firmware updates, 262
DC waveform generator output, 201 E firmware upgrade files, 251
dead time (re-arm), 156 firmware version information, 241
decibels, FFT vertical units, 69 ECL threshold, 87 firmware versions, 251
decimating samples, 147 edge speeds, 146 flash drive, 35
decimation, for measurement record, 270 edge triggering, 113 Flat top FFT window, 68
decimation, for screen, 270 EDK license, 261 folding frequency, 143
default configuration, 25 either edge trigger, 115 forcing a trigger, 113
default label library, 109 English user interface and Quick Help, 41 freeze display, 239
default setup, 25, 217 Entry knob, 30 freeze display, Quick Freeze Display, 239
Default Setup key, 31 Entry knob, push to select, 30 French front panel overlays, 36
defaults, waveform generator, 204 erase, secure, 217 French user interface and Quick Help, 41
delay knob, 45 expand about, 57, 229 Frequency measurement, 180
Delay measurement, 170, 182 expand about center, 230 frequency requirements, power source, 23
delay time indicator, 53 expand about ground, 229 frequency, Nyquist, 143
delayed sweep, 50 exporting waveform, 205 front panel controls and connectors, 28
delete character, 214 EXT TRIG IN as Z-axis input, 50 front panel self test, 236
delete file, 227 EXT TRIG IN connector, 38 front panel, language overlay, 35
Demo 1 terminal, 34 external memory device, 35 front panel, real scope remote, 244
Demo 2 terminal, 34 external trigger, 138 front panel, simple remote, 245
DHCP, 225, 226 external trigger, input impedance, 139
differential probes, 259 external trigger, probe attenuation, 139 G
Digit softkey, 118 external trigger, probe units, 139
digital bus mode, 88 g(t), 64
digital channel controls, 32 F gateway IP, 225
digital channel inputs, 35 Gaussian frequency response, 144
digital channel menu, 86 f(t), 65 German front panel overlays, 36
digital channels, 86 factory default settings, 217 German user interface and Quick Help, 41
digital channels, AutoScale, 83 Fall time measurement, 182 glitch capture, 149
digital channels, enabling, 262 fast debug AutoScale, 231 glitch trigger, 119
digital channels, logic threshold, 86 FFT aliasing, 72 golden waveform test, 187
digital channels, probing, 91 FFT DC value, 72 GPIB address, 224
digital channels, size, 85 FFT measurement hints, 71 GPIB interface, remote control, 223

Index
GPIB module, 22, 37 invert graticule colors, 208 low-frequency noise rejection, 136
GPIB module installation, 22 invert waveform, 59
grabber, 81, 82 IP address, 225, 241 M
graphical user interface language, 41 Italian front panel overlays, 36
graticule intensity, 103 Italian user interface and Quick Help, 41 mask files, recall, 216
graticule type, 102 MASK license, 261
grid intensity, 103 J mask test, trigger output, 191, 233
grid type, 102 mask testing, 187
ground level, 56 Japanese front panel overlays, 36 mask, TRIG OUT signal, 233
Ground terminal, 34 Japanese user interface and Quick Math key, 32
Help, 41 math, 1*2, 65
H math, addition, 66
K math, FFT, 67
Hanning FFT window, 68 math, functions, 63
hardware self test, 236 keys, front panel, 28 math, multiply, 65
Help key, 33 knobs, front panel, 28 math, offset, 65
help, built-in, 40 Korean front panel overlays, 36 math, scale, 65
hex bus trigger, 118 Korean user interface and Quick Help, 41 math, subtract, 66
Hex softkey, 118 math, transform functions on arithmetic
HF Reject, 137 L operations, 64
high-frequency noise rejection, 137 math, units, 65, 74
high-resolution mode, 147, 153 Label key, 34 math, using waveform math, 63
holdoff, 138 label list, 109 MATLAB binary data, 263
Horiz key, 31, 43, 48, 50, 150 label list, loading from text file, 108 Maximum measurement, 172
Horizontal controls, 31, 47 labels, 105 maximum sample rate, 147
horizontal Navigate key, 31 labels, auto-increment, 108 Meas key, 33, 167
horizontal position control, 31 labels, default library, 109 Measure controls, 33
horizontal position knob, 45 LAN connection, 225 measure, Quick Measure All, 238
horizontal scale fine adjustment, 52 LAN interface, remote control, 223 measurement category, definitions, 256
horizontal Search key, 31 LAN port, 37 measurement definitions, 169
horizontal sweep speed control, 31 LAN Settings softkey, 225, 226 measurement record, 212
horizontal time/div control, 31 LAN/VGA module, 22, 37 measurement thresholds, 184
horizontal Zoom key, 31 LAN/VGA module installation, 22 measurement window with zoom
host name, 225, 241 landscape mode, 222 display, 186
Host name softkey, 226 language, user interface and Quick measurements, 169
Help, 41 measurements, automatic, 167
I length control, 211 measurements, delay, 170
length softkey, 209, 210 measurements, overshoot, 170
I/O interface settings, 223 level, trigger, 112 measurements, phase, 170
identification function, web interface, 250 LF Reject, 136 measurements, preshoot, 170
impedance, digital probes, 91 library, labels, 107 measurements, time, 179
indeterminate state, 159 licenses, 261, 262 measurements, voltage, 171
infinite persistence, 101, 142, 149 line voltage, 23 MegaZoom IV, 4
information area, 39 load file, 227 memory depth and sample rate, 147
installed licenses, 236 Load from, 214 memory, segmented, 153
installed options, 251 localized front panel overlay, 35 menu line, 39
Instrument Utilities web page, 251 Location, 214, 228 Minimum measurement, 172
intensity control, 99 logic presets, waveform generator, 203 Mode/Coupling key, trigger, 133
Intensity key, 29 logic threshold, 86 model number, 236, 241

Index
Modify softkey, 226 passive probes, 258 probes, connecting to oscilloscope, 24

module installed, 236 passive probes, compensating, 27 probes, current, 259
module slot, 37 password (network), reset, 254 probes, differential, 259
MSO, 3 password (network), setting, 252 probes, digital, 79
MSO feature upgrade, 262 pattern trigger, 116 probes, passive, 258
MSO license, 261 PC connection, 226 probes, passive, compensating, 27
Multicast DNS, 225 peak detect mode, 147, 148, 149 programmer's guide, 247
Multiply math function, 65 Peak-peak measurement, 172 pulse polarity, 120
Period measurement, 179 pulse waveform generator output, 201
N persistence, 101 pulse width trigger, 119
persistence, clearing, 102
navigate files, 227 persistence, infinite, 142 Q
Navigate key, 31 Phase measurement, 170, 183
navigating the time base, 53 phase X cursor units, 160 qualifier, pulse width, 120
network configuration parameters, 241 PNG file format, 206 Quick Action key, 30, 238
network printer connection, 220 point-to-point connection, 226 Quick Clear Display, 239
network, connecting to, 225 pollution degree, 257 Quick Freeze Display, 239
new label, 107 pollution degree, definitions, 257 Quick Help, 40
noise rejection, 137 Portuguese front panel overlays, 36 Quick Help language, 41
noise waveform generator output, 201 Portuguese user interface and Quick Quick Measure All, 238
noise, high-frequency, 137 Help, 41 Quick Print, 238
noise, low-frequency, 136 position digital channels, 87 Quick Recall, 239
noisy signals, 133 position knob, 87 Quick Save, 238
non-volatile memory, secure erase, 217 position, analog, 57 Quick Trigger Mode, 239
normal acquire mode, 148 post-processing, 167
normal mode, 147, 148 post-trigger information, 45 R
Normal trigger mode, 134 power consumption, 23
notices, 2 power cord connector, 37 ramp waveform generator output, 201
Nyquist frequency, 73 power requirements, 23 random noise, 133
Nyquist sampling theory, 143 power supply, 37 ratio X cursor units, 160
power switch, 24, 29 ratio Y cursor units, 160
O power-on, 23 raw acquisition record, 212
predefined labels, 106 Real Scope Remote Front Panel, 244
options, print, 221 Preshoot measurement, 170, 175 rear panel connectors, 37
oscilloscope bandwidth, 144 Press to go, 214, 228 re-arm time, 156
oscilloscope bandwidth required, 146 pre-trigger information, 45 recall, 239
oscilloscope rise time, 145 print, 238 recall files via web interface, 249
oscilloscope sample rate, 145 Print key, 33 recall mask files, 216
output load, waveform generator, 203 print options, 221 recall setups, 215
output, trigger, 232 print screen, 219 recall, Quick Recall, 239
overlay, localized, 35 print, landscape, 222 Rectangular FFT window, 69
Overshoot measurement, 170, 174 print, Quick Print, 238 Ref key, 32, 75
overvoltage category, 257 printer, USB, 35, 219 reference point, waveform, 229
printing the display, 219 reference waveforms, 75
P probe attenuation, 60 remote control, 223
probe attenuation, external trigger, 139 Remote Front Panel, 246
palette, 208 probe compensation, 34 remote programming, Agilent IO
pan and zoom, 44 probe units, 60 Libraries, 247
parts, replacement, 96 probes, 258, 260 remote programming, web interface, 246

Index
replacement parts, 96 serial number, 236, 241 T

required oscilloscope bandwidth, 146 service functions, 233
reset network password, 254 Set all Digits softkey, 118 template, front panel, 35
return instrument for service, 237 setup files, saving, 207 test, mask, 187
Rise time measurement, 182 setup, automatic, 83 theory, sampling, 143
rise time, oscilloscope, 145 setup, default, 25 threshold, analog channel
rise time, signal, 146 setups, recall, 215 measurements, 184
roll mode, 47 SGM, 153 threshold, digital channels, 86
Run Control keys, 31 SGM license, 261 thumb drive, 35
runt pulses, 179 shipping damage, 19 tilt for viewing, 22
Russian front panel overlays, 36 shipping precautions, 237 time measurements, 179
Russian user interface and Quick Help, 41 Sigma, minimum, 190 time reference indicator, 53
Simple Remote Front Panel, 245 time, re-arm, 156
Simplified Chinese front panel overlays, 36 timebase, 47
S Simplified Chinese user interface and Quick times for saving data, 212
safety warning, 25 Help, 41 Tools keys, 30
sample rate, 4 sine waveform generator output, 201 Top measurement, 173
sample rate and memory depth, 147 single acquisition, 31 tracking cursors, 159
sample rate, current rate displayed, 44 Single key, 141 trademarks, 2
sample rate, oscilloscope, 144, 145 single-shot acquisitions, 135 Traditional Chinese front panel overlays, 36
sampling theory, 143 single-shot events, 141 Traditional Chinese user interface and Quick
sampling, overview, 143 size, 85 Help, 41
save, 238 skew, analog channel, 61 transient withstand capability, 257
save file, 227 slope trigger, 113 Transparent backgrounds, 230
save files via web interface, 247 Snapshot All measurements, 171 TRIG OUT connector, 38, 232
save segment, 209 snapshot all, quick action, 238 Trig'd trigger indicator, 135
save setup files, 207 softkey labels, 40 Trig'd? trigger indicator, 135
save times, data, 212 softkeys, 6, 29 Trigger controls, 30
Save to, 214 software updates, 262 trigger coupling, 136
save, Quick Save, 238 software version, 236 trigger indicator, Auto?, 135
save/recall from web interface, 247 Span, FFT, 68 trigger indicator, Trig'd, 135
Save/Recall key, 33 Spanish front panel overlays, 36 trigger indicator, Trig'd?, 135
saver, screen, 230 Spanish user interface and Quick Help, 41 trigger level, 112
saving data, 205 specifications, 255 trigger mode, auto or normal, 134
SCPI Commands window, 246 spectral leakage, FFT, 74 trigger mode, Quick Trigger Mode, 239
screen image via web interface, 249 square waveform generator output, 201 trigger output, 232
screen saver, 230 square waves, 144 trigger output, mask test, 191, 233
Search key, 31 stand-alone connection, 226 trigger type, edge, 113
secure erase, 217 start acquisition, 31 trigger type, glitch, 119
segmented memory, 153 statistics, mask test, 192 trigger type, hex bus, 118
segmented memory, re-arm time, 156 status line, 39 trigger type, pattern, 116
segmented memory, saving segments, 209 status, User Cal, 237 trigger type, pulse width, 119
select digital channels, 87 Std Deviation measurement, 177 trigger type, slope, 113
select knob, 87 stop acquisition, 31 trigger type, video, 121
Selected, 228 storage locations, navigate, 214 trigger types, 111
selecting, values, 30 subnet mask, 225 trigger, definition, 112
self test, front panel, 236 subtract math function, 66 trigger, external, 138
self test, hardware, 236 sync pulse, waveform generator, 202 trigger, forcing a, 113
serial decode controls, 32 trigger, general information, 112

Index
trigger, holdoff, 138 vertical scale knobs, 34

trigger, mode/coupling, 133 vertical sensitivity, 34, 57
trigger, source, 113 Vertical Units, FFT, 69
triggers, TRIG OUT signal, 232 VGA video output, 37
TTL threshold, 87 video trigger, 121
turn channel on, 34 viewing, tilt the instrument, 22
VISA connect string, 241
U voltage measurements, 171
under-sampled signals, 143 W

units, cursor, 160
units, external trigger probe, 139 warranted specifications, 255
units, math, 65, 74 warranty, 237
units, probe, 60 Wave Gen key, 30, 35
updating software and firmware, 262 waveform generator, 199
upgrade files, 251 waveform generator defaults,
upgrade options, 261 restoring, 204
upgrading the oscilloscope, 262 waveform generator logic presets, 203
upload new firmware, 241 waveform generator output load, 203
usb, 229 waveform generator sync pulse, 202
USB device port, 38 waveform generator sync pulse, TRIG OUT
USB device port, remote control, 223 signal, 233
USB host port, 38, 219 waveform generator, waveform type, 199
USB host ports, 35 Waveform keys, 33
USB printer, 219 waveform type, waveform generator, 199
USB printers, supported, 219 waveform, cursor tracking, 159
USB storage device, 35 waveform, intensity, 99
USB, CD device, 229 waveform, printing, 219
USB, eject device, 35 waveform, reference point, 229
USB, storage device numbering, 229 waveform, saving/exporting, 205
usb2, 229 WAVEGEN license, 261
user cal, 234 web interface, 241
user calibration, 234 web interface, accessing, 242
user interface language, 41 Width - measurement, 181
User-defined threshold, 87 Width + measurement, 181
utilities, 223 Window, FFT, 68
Utility key, 30
X
V
XY mode, 47, 48
V RMS, FFT vertical units, 69
values, choosing, 30 Z
variable persistence, 101
ventilation requirements, 23 Z-axis blanking, 50
vernier, channel, 58 zoom and pan, 44
Vertical controls, 34 zoom display, measurement window
vertical expansion, 57 with, 186
vertical position, 57 Zoom key, 31
vertical position knobs, 34

Oscilloscope PDF

Uploaded by

Copyright:

Available Formats

Oscilloscope PDF

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Oscilloscope PDF

Uploaded by

Copyright:

Available Formats

Agilent InfiniiVision

2 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Table 1 2000 X-Series Model Numbers, Bandwidths

Bandwidth 70 MHz 100 MHz 200 MHz

4-Channel + 8 Logic MSO-X 2004A MSO-X 2014A MSO-X 2024A

The Agilent InfiniiVision 2000 X- Series oscilloscopes deliver these features:

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 3

4 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 5

6 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Maximum input voltage at analog inputs 24

Do not float the oscilloscope chassis 24

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 7

8 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Probe cable for digital channels 80

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 9

10 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Maximum voltage at oscilloscope external trigger input 139

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 11

12 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 13

16 Save/Recall (Setups, Screens, Data)

14 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 15

Maximum input voltage at analog inputs 257

Maximum input voltage at digital channels 257

16 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 17

Inspect the Package Contents

• InfiniiVision 2000 X- Series oscilloscope.

20 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

InfiniiVision 2000 X-Series oscilloscope

Digital Probe Kit*

*N6459-60001 Digital Probe Kit contains:

Digital probe replacement parts are listed in the

See Also • “Accessories Available" on page 260

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 21

Install the Optional LAN/VGA or GPIB Module

Tilt the Oscilloscope for Easy Viewing

22 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Power-On the Oscilloscope

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 23

2 The oscilloscope automatically adjusts for input line voltages in the

3 Press the power switch.

Connect Probes to the Oscilloscope

Maximum input voltage at analog inputs

Do not float the oscilloscope chassis

24 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Recall the Default Oscilloscope Setup

Table 2 Default Configuration Settings

Vertical (Analog) Channel 1 on, 5 V/div scale, DC coupling, 0 V position.

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 25

Use Auto Scale

2 If you want to return to the oscilloscope settings that existed before,

26 Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Compensate Passive Probes

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide 27

If necessary, use a nonmetallic tool (supplied with the probe) to adjust

7 Connect probes to all other oscilloscope channels (channel 2 of a

Learn the Front Panel Controls and Connectors