Panasonic

SIP Trunking
User Guide

nextiva.com/support
 2|P a g e

Contents

Overview .................................................................................................................................................................. 3
DSP card and Activation keys.................................................................................................................................. 3
Architecture Overview ............................................................................................................................................ 4
Port Forwarding rules on the end router ................................................................................................... 4
Basic V-SIPGW16 Settings for Nextiva SIP Trunks.................................................................................................. 5
1. Install the NS Unified Web Maintenance console on your PC .............................................................. 5
2. Connect to the PBX ................................................................................................................................. 5
3. Configure the LAN Settings of the PBX ................................................................................................... 7
4. Installing V-SIPGW16 cards ..................................................................................................................... 8
5. Configuring the V-SIPGW16 Card ......................................................................................................... 10
6. Configuring Incoming DID Call Routing ................................................................................................ 13
7. Backup and Reset .................................................................................................................................. 13
SIP Trunk Activation Keys ...................................................................................................................................... 14
Useful Hints ............................................................................................................................................................ 14
Important Notes .................................................................................................................................................... 14

Nextiva, All Rights Reserved

 3|P a g e

Overview

This document outlines the configuration settings required for the Panasonic KX-NS1000 and KX-NS700
PBX (Private branch exchange) to make full use of the capabilities of Nextivas SIP Trunking services.

The SIP Trunking services of the Panasonic KX-NS1000/700 PBX are provided through virtual CO line cards
(VSIPGW16), which can be easily integrated with Nextivas VoIP service. This guide describes the specific
configuration items for the Virtual SIP Gateway Card in addition to the basic PBX configuration related to SIP
Trunking functionality.

DSP card and Activation keys

The PBX must be equipped with a DSP card in order to provide communication between the TDM side of the
PBX and the Nextiva SIP trunks
Activation keys for SIP-Trunks must be installed in the PBX to provide SIP-trunk functionality

To check the number of activation keys installed in the PBX and add new licenses, please refer to
Page 13 in this configuration guide.

Nextiva, All Rights Reserved

 4|P a g e

Architecture Overview

The above diagram illustrates simple VoIP networks connecting the NS1000/700 PBX. Nextiva will provide its
services over the Public Internet.

Port Forwarding rules on the end router:

Forward Port (UDP) 35060 to the PBX IP address

Forward Port Range (UDP) 12000 - 12511 to the VOIP-DSP#1-1 IP address
Forward Port Range (UDP) 12512 - 13023 to the VOIP-DSP#1-2 IP address
Forward Port Range (UDP) 13024 - 13535 to the VOIP-DSP#2-1 IP address
Forward Port Range (UDP) 13536 - 13047 to the VOIP-DSP#2-2 IP address

Nextiva, All Rights Reserved

 5|P a g e

Basic V-SIPGW16 Settings for Nextiva SIP Trunking

1. Install the NS Unified Web Maintenance console on your PC

a. The maintenance console is available for certified dealers. Dealers can get the latest version of the
UPCMC from www.panasonicpartnerportal.com (UPCMC version 5.10.1 or higher)

2. Connect to the PBX

a. Start the UPCMC.

b. Click Connect and enter the IP Address to connect to your PBX for interactive configuration.

KX-NS700 KX-NS1000

Nextiva, All Rights Reserved

 6|P a g e

c. Enter the username and password to log in to the PBX.

Default Username: INSTALLER
Default Password: 1234

d. Complete the Easy Setup Wizard configuration (if starting at factory default).

Nextiva, All Rights Reserved

 7|P a g e

3. Configure the LAN Settings of the PBX

a. Click on Setup.

b. Go to Network Service 1.IP Address/Ports Basic Settings tab

c. Based on your Local LAN, assign static IP addresses to the PBX. The default gateway should be the end
routers network IP address.

IP Address: provided by LAN administrator

Subnet Mask: provided by LAN administrator
Default Gateway: provided by LAN administrator
Preferred DNS IP Address: provided by LAN administrator
Alternative DNS IP Address: provided by LAN administrator
DSP Card #1 1: provided by LAN administrator
DSP Card #1 2: provided by LAN administrator

(NS1000 Only)
DSP Card #2 1: provided by LAN administrator
DSP Card #2 2: provided by LAN administrator

Nextiva, All Rights Reserved

 8|P a g e

d. Select Apply, then click OK.

4. Installing V-SIPGW16 cards

KX-NS1000
a. Go to PBX Configuration 1.Configuration 1.Slot Virtual Shelf V-SIPGW16 tab.

b. Click the dropdown menu, and select the number of V-SIPGW16 Cards to add for your installation.

Nextiva, All Rights Reserved

 9|P a g e

KX-NS700
a. Go to PBX Configuration 1.Configuration 1.Slot Select the Virtual Shelf

b. Drag Drop V-SIPGW16 Cards to the virtual Trunk slots (1 - 4) as needed and click OK.

Nextiva, All Rights Reserved

 10 | P a g e

5. Configuring the V-SIPGW16 Card

a. Move your cursor over the V-SIPGW16 Card and click OUS to take the card out of service.

b. Shelf Property settings: Move your cursor over the V-SIPGW16 Card and select Shelf Property.

c. Change the following parameters from their default value:

Main Tab
NAT Keep Alive Packet Sending Ability: Enable

Timer Tab
leave at factory default setting

d. Select Apply and then click OK to exit the Shelf Property settings screen.

Nextiva, All Rights Reserved

 11 | P a g e

e. Card Property settings:

Move your cursor over the V-SIPGW16 card and choose Card Property.
leave at factory default setting

f. Select Apply and then click OK to exit the Card Property settings screen.

g. Port Property settings:

Move your cursor over the V-SIPGW16 card and choose Port Property.

Nextiva, All Rights Reserved

 12 | P a g e

h. Change the following parameters from their default value:

Main Tab
Connection Attribute: Basic Channel + Additional Channels
Provider Name: Nextiva
SIP Server Name: pai.voipdnsservers.com
Account Tab
User Name: provided by Nextiva
Authorization ID: provided by Nextiva
Authorization Password: provided by Nextiva
Register Tab
leave at factory default setting
NAT Tab
leave at factory default setting
Option Tab
leave at factory default setting
Calling Party Tab
From Header - User Part: PBX-CLIP
P-Asserted-Identity Header: Enable
Called Party Tab
leave at factory default setting
Voice/FAX Tab
leave at factory default setting
RTP/RTCP Tab
leave at factory default setting
T.38 Tab
leave at factory default setting
T.38 Option Tab
leave at factory default setting
DSP Tab
leave at factory default setting
Supplementary Service Tab
CNIP (Receive): Yes
Advanced
Leave at factory default setting

i. Select Apply, and then click OK to exit the Port Property settings screen.

Nextiva, All Rights Reserved

 13 | P a g e

6. Configuring Incoming DID Call Routing

a. Go to PBX Configuration 10.CO & Incoming Call 3.DDI/DID Table

b. Enter the 10-digit DDI / DID Numbers.

c. Enter the desired Day/Lunch/Break/Night destination extension for each DDI / DID.

d. Select Apply and then click OK to exit the DDI / DID Table settings screen.

7. Backup and Reset

a. Click on Maintenance System Control 4.System Reset

b. Click Backup.

c. Click OK.

d. Click OK.

e. NS system will restart.

Nextiva, All Rights Reserved

 14 | P a g e

SIP Trunk Activation keys:

1. To obtain Activation Keys, you need to purchase the appropriate IP Trunk activation key models and access
the Key Management System to register them to your PBX at http://tde.panacare.com.

KX-NSM102: 2-Channel IP Trunk Activation Key (2 IP Trunk)

KX-NSM104: 4-Channel IP Trunk Activation Key (4 IP Trunk)
KX-NSM108: 8-Channel IP Trunk Activation Key (8 IP Trunk)
KX-NSM116: 16-Channel IP Trunk Activation Key (16 IP Trunk)

2. You will need the MPR ID from the PBX to register the Activation Key(s) on the Key Management System.

3. To check the Number of Activation Keys Installed in your system and the MPR ID:
PBX Configuration 1.Configuration 1.Slot Activation Key

Minimum System Software requirements:

NS Unified Web Maintenance Console v5.10.1

KX-NS1000 v4.10060

KX-NS700 v4.10064

Useful Tips:
1. Update your system software once an update is available through the Dealer website to make use of
added features and improved functionality.
2. Update your UPCMC (Maintenance Tool) with the latest version available on the BTS website.
3. Back up your PBX configuration file with the good known settings.
4. Consult with your network administrator prior to installation to guarantee a smooth setup for your
system over the existing network.

Important Notes:

E911: Please work closely with the Nextiva team to ensure that E911 service is configured and tested properly.

Nextiva, All Rights Reserved