Networking Topologies

Networking Topologies
A network consists of two or more computers that are linked in order to share resources (such as
printers and CD-ROMs), exchange files, or allow electronic communications. The computers on a network
may be linked through cables, telephone lines, radio waves, satellites, or infrared light beams.
Types of topologies
 Linear Bus
 Star
 Ring
 Tree
 Mesh
1. Linear or bus topology- A linear bus topology consists of a main run of cable with a
terminator at each end. All nodes (file server, workstations, and peripherals) are connected to the
linear cable. Ethernet and LocalTalk networks use a linear bus topology.
Advantages of a Linear Bus Topology

• Easy to connect a computer or peripheral to a linear bus.
• Requires less cable length than a star topology.
Disadvantages of a Linear Bus Topology
• Entire network shuts down if there is a break in the main cable.
• Terminators are required at both ends of the backbone cable.
• Difficult to identify the problem if the entire network shuts down.
• Not meant to be used as a stand-alone solution in a large building.
2. Star topology-
• A star topology is designed with each node (file server, workstations, and peripherals)
connected directly to a central network hub or concentrator
• Data on a star network passes through the hub or concentrator before continuing to its
destination. The hub or concentrator manages and controls all functions of the network. It
also acts as a repeater for the data flow. This configuration is common with twisted pair
cable; however, it can also be used with coaxial cable or fiber optic cable.
Advantages of a Star Topology
• Easy to install and wire.
• No disruptions to the network then connecting or removing devices.
• Easy to detect faults and to remove parts.
Disadvantages of a Star Topology
• Requires more cable length than a linear topology.
• If the hub or concentrator fails, nodes attached are disabled.
• More expensive than linear bus topologies because of the cost of the
concentrators.
3. Tree topology-
• A tree topology combines characteristics of linear bus and star topologies.
• It consists of groups of star-configured workstations connected to a linear bus backbone
cable.
• Tree topologies allow for the expansion of an existing network, and enable schools to
configure a network to meet their needs.
Advantages of a Tree Topology

• Point-to-point wiring for individual segments.
• The network doesn`t fail even when a link between two nodes is broken.
• Supported by several hardware and software venders.
Disadvantages of a Tree Topology
• Overall length of each segment is limited by the type of cabling used.
• If the backbone line breaks, the entire segment goes down.
• More difficult to configure and wire than other topologies.
4. Ring topology-The ring topology is a type of computer network configuration where each
network computer and device are connect to each other forming a large circle. Each packet is sent
around the ring until it reaches its final destination.
Advantages of a Ring Topology
• Growth of system has minimal impact on performance
• All stations have equal access
• The network doesn`t fail even when a link between two nodes is broken.
Disadvantages of a Ring Topology
• Most expensive topology
• Failure of one computer may impact others
• Complex
5. Mesh topology-
• It requires that every terminal should be attached to each other.
• All the computers must have adequate number of interfaces for the connections to be made.
Because of this requirement the installations is somewhat difficult.
• The length of cable required is quite higher as compared to other topologies.
Advantages of a Mesh Topology

• System provides increased redundancy and reliability as well as ease of
troubleshooting.
• Data transfer is faster.
• Addition & deletion of node is easy.
Disadvantages of a Mesh Topology
• System is expensive to install because it uses a lot of cabling.
\
6. Hybrid topology-It is a mixture of above mentioned topologies. Usually, a central
computer is attached with sub-controllers which in turn participate in a variety of topologies.
Advantages of a Hybrid Topology

 It is extremely flexible.
 It is very reliable.
Disadvantages of a Hybrid Topology
 Expensive
 Addition of node is not easy.
Considerations When Choosing a Topology:
 Money. A linear bus network may be the least expensive way to install a network; you
do not have to purchase concentrators.
 Length of cable needed. The linear bus network uses shorter lengths of cable.
 Future growth. With a star topology, expanding a network is easily done by adding
another concentrator.
 Cable type. The most common cable in schools is unshielded twisted pair, which is
most often used with star topologies.

Networking Topologies

Uploaded by

Copyright:

Available Formats

Networking Topologies

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Networking Topologies

Uploaded by

Copyright:

Available Formats

Networking Topologies

Advantages of a Linear Bus Topology

Advantages of a Tree Topology

Advantages of a Mesh Topology

Advantages of a Hybrid Topology

You might also like