[00]COVER.

fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２５分

CODE : 00ZAR5320/A1E

DIGITAL COPIER
AR-5316
AR-5316

MODEL AR-5320

AR-5320
(with option installed)

CONTENTS

[ 1 ] NOTE FOR THIS SERVICE MANUAL . . . . . . . . . . . . . . . Refer to AR-M160

[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320
[ 3 ] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320
[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . .AR-5316/5320
[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . .AR-5316/5320
[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to AR-M160
[ 7 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320
[ 8 ] USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320
[ 9 ] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to AR-M160
[10] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320
[11] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . Refer to AR-M160
[12] FLASH ROM VERSION UP PROCEDURE . . . . . . . . . . . Refer to AR-M160
[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320

Parts marked with “ “ are important for maintaining the safety of the set.
Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for

SHARP CORPORATION after sales service only.
The contents are subject to change without notice.
[01_02]NOTE_SPEC.fm 1 ページ ２００３年１２月１９日　金曜日　午後４時９分

[1] NOTE FOR THIS SERVICE MANUAL

This Service Manual describes only the items related to the AR-5316 and AR-5320. For the other items common with the AR-M160/M205, please refer
to the AR-M160/205 Service Manual (Document code:00ZARM205/A1E). The table below shows which document(s) should be referred to for each
section. (Refer to the document marked with O.)

Section AR-M160/M205 AR-5316/AR-5320 Changed item

[ 1 ] GENERAL O
[ 2 ] SPECIFICATIONS O O Some specifications
[ 3 ] CONSUMABLE PARTS O
[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES O O Appearance / Internal / Operation panel
[ 5 ] UNPACKING AND INSTALLATION O O Changing the copy paper size in the tray
[ 6 ] ADJUSTMENTS O
[ 7 ] SIMULATIONS O O Shifter sensors status display, etc. deleted.
[ 8 ] USER PROGRAMS O O USB2.0 mode switch, etc. deleted.
[ 9 ] TROUBLE CODE LIST O
[10] MAINTENANCE O
[11] DISASSEMBLY AND ASSEMBLY O
[12] FLASH ROM VERSION UP PROCEDURE O
[13] ELECTRICAL SECTION O O Block diagram / Actual wiring diagram 1/7

[2] SPECIFICATIONS
The table below shows the specifications of this model and the contents of changes from the AR-M160/M205 and AR-5316/5320.
Item AR-M160 AR-5316 AR-M205 AR-5320
Paper feed system 1cassette + One automatic feeding paper 2cassette + Two automatic feeding paper
Multi manual paper feed tray(250sheets) + Multi manual paper feed trays(250sheets each) +
bypass tray(100sheets) bypass tray(100sheets)
Weight Approx.31.3Kg Approx.31.3Kg Approx.35.1Kg Approx.36.3Kg
(Not including TD cartridge) (Not including TD cartridge)
Interface USB1.1/USB2.0 IEEE1284parallel connector/ USB1.1/USB2.0 IEEE1284parallel connector/
IEEE1284 USB1.1 IEEE1284 USB1.1

Option
Machine Model AR-M160 AR-M205 AR-5316 AR-5320 Remark
250 sheets paper feed unit AR-D24 / D25 O O - -
SPF AR-SP6 O - O O
RSPF AR-RP6 - O - -
Original cover AR-VR5 Standard O Standard Standard

O : The option can be installed.

- : The option cannot be installed.

AR-5316/5320 NOTE FOR THIS SERVICE MANUAL 1-1

[03]CONSUMABLEPARTS.fm 1 ページ ２００４年１月１９日　月曜日　午後１時４９分

[3] CONSUMABLE PARTS

1. Supply system table
A. East Europe / Russia
NO Name Content Life Product name Remark
1 Toner cartridge(Black) Toner x10 160K AR-016LT Life setting by A4 6% document
<With IC> (Toner: Net Weight 537g) LT=T*10
Vinyl bag x10
2 Developer Developer x10 500K AR-202LD LD=DV*10
(Developer : Net Weight 400g)
3 Drum kit Drum x1 50K AR-202DM
Drum fixing plate x1
Note 1: The individual carton is printed with English, German, French, and Spanish as well as the green mark.
B. Middle East / Africa / Philippine
NO Name Content Life Product name Remark
1 Toner cartridge(Black) Toner x10 190K AR-016ET Life setting by A4 6% document
<With IC> (Toner: Net Weight 537g) ET=FT*10
Vinyl bag x10
2 Developer Developer x10 500K AR-202CD CD=SD*10
(Developer : Net Weight 400g)
3 Drum kit Drum x1 50K AR-202DR
Drum fixing plate x1
Note 1: The individual carton is printed with English, German, French, and Spanish as well as the green mark.
C. Asia
NO Name Content Life Product name Remark
1 Toner cartridge(Black) Toner x10 190K AR-016CT Life setting by A4 6% document
<With IC> (Toner: Net Weight 537g) CT=ST*10
Vinyl bag x10
2 Developer Developer x10 500K AR-202CD CD=SD*10
(Developer : Net Weight 400g)
3 Drum kit Drum x1 50K AR-202DR
Drum fixing plate x1
Note 1: The individual carton is printed with English, German, French, and Spanish as well as the green mark.
D. Hong Kong
NO Name Content Life Product name Remark
1 Toner cartridge(Black) Toner x10 190K AR-016CT-C Life setting by A4 6% document
<With IC> (Toner: Net Weight 537g) CT-C=ST-C*10
Vinyl bag x10
2 Developer Developer x10 500K AR-202CD-C CD-C=SD-C*10
(Developer : Net Weight 400g)
3 Drum kit Drum x1 50K AR-202DR-C
Drum fixing plate x1
Note 1: The individual carton is printed with English and Chinese as well as the green mark.

AR-5316/5320 CONSUMABLE PARTS 3-1

[04]EXTERNALVIEWS.fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２６分

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance

1
6 5
1

15 2
3
16 3
9
4 7
10
14

8 11 12 13

1 Document feeder cover (when the SPF 2 Document glass 3 Handles

is installed) /document cover
4 Power switch 5 Operation panel 6 Paper output tray
7 Front cover 8 Paper trays 9 Side cover
10 Side cover handle 11 Bypass tray guides 12 Bypass tray
13 Bypass tray extension 14 Charger cleaner 15 USB 1.1 connector
16 Parallel connector

2. Internal
17 18 19

20 21

22

24 25 26 27
23

17 Document feeder tray 18 Original guides 19 Feeding roller cover

(when the SPF is installed) (when the SPF is installed) (when the SPF is installed)
20 Right side cover 21 Exit area 22 Toner cartridge lock release lever
(when the SPF is installed) (when the SPF is installed)
23 Toner cartridge 24 Roller rotating knob 25 Fusing unit release levers
26 Photoconductive drum 27 Fusing unit paper guide

AR-5316/5320 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1

[04]EXTERNALVIEWS.fm 2 ページ ２００３年１２月１９日　金曜日　午後３時２６分

3. Operation Section
1 2 3

The indications of the operation panel may differ

depending on the country and the region.

AR-5316/ The example of a display of inch series

AR-5316X 200%
11X17 141
8½X14
129
121
8½X11 100%
8½X5½ 95
8½X11 77
8½X13 64
EXTRA 50%
4 5 6 7 4 5 8

1 ON LINE key/indicator 2 DUAL PAGE COPY key/indicator 3 XY-ZOOM key/indicator

4 SPF indicator 5 Paper feed location / misfeed location 6 ORIGINAL SIZE ENTER key /
(when the SPF is installed) indicators ORIGINAL SIZE indicators
7 PAPER SIZE indicators 8 PRESET RATIO selector keys /
indicators

11
9 10 12 13 14 15 16 17 18

ACC.#-C AUTO ZOOM 25 400% INTERRUPT

AUTO 200%
141
A3 122
A4 115
A4 100%
A5 86
B4 81
EXTRA 70
1 3 5 50%

ENTER AUTO %

19 6 7 20 4 21 22 5 8 23 24 25 26 27

Not used for this machine.

9 AUTO/TEXT/PHOTO key / indicators 10 AUDIT CLEAR key 11 AUTO PAPER SELECT indicator
12 Alarm indicators 13 POWER SAVE indicator 14 Display
15 Copy ratio display key 16 ZOOM indicator 17 Zoom keys
18 INTERRUPT key / indicator 19 Light and Dark keys / indicators 20 PAPER SIZE ENTER key
21 TRAY SELECT key 22 AUTO IMAGE key / indicator 23 Numeric keys
24 # key 25 START key / indicator 26 CLEAR ALL key
27 CLEAR key

AR-5316/5320 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-2

[05]UNPACKING.fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２６分

[5]UNPACKING AND INSTALLATION 4) Squeeze the lock lever of the front guide and slide the front guide to
match the width of the paper, and move the left guide to the
appropriate slot as marked on the tray.
5. Changing a tray's paper size setting
Follow these steps to change a tray's paper size setting.
Left guide
Note:
•The paper size setting cannot be changed when the machine has
stopped temporarily due to running out of paper or a misfeed, or during
interrupt copying.
•During printing (even in copy mode), the paper size setting cannot be
changed.
•A5 size paper can only be selected in upper paper tray.
•Do not load paper that is a different size than the paper size setting.
Front guide
Copying will not be possible.

1) Hold down the [PAPER SIZE ENTER] key for more than 5 seconds to
•The front guide is a slide-type guide. Grasp the locking knob on the
set the selected paper size.
guide and slide the guide to the indicator line of the paper to be loaded.
The currently selected paper feed location indicator will blink and the
•The left guide is an insert-type guide. Remove it and then insert it at the
corresponding paper size (which is currently set) indicator will light
indicator line of the paper to be loaded.
steadily.
•When using 11" x 17" sized paper store the left guide in the slot at the
All other indicators will go out.
left front of the paper tray.

A3
A4
A4
A5
B4
XTRA

2) If the machine has two paper trays, use the [TRAY SELECT] key to
select the paper tray for which you wish to change the paper size
setting. 5) Press the [START] key and then the [PAPER SIZE ENTER] key.
Each time the [TRAY SELECT] key is pressed, a paper tray will be To change the paper size setting of another tray, repeat steps 2) to 5)
indicated with a blinking paper feed location indicator. after pressing the [START] key.

Note: Affix the paper size label for the paper size selected in step 3) to
3) Use the [ORIGINAL SIZE ENTER] key to select the paper size. the label position on the right end of the tray.
The indicator of the selected paper size lights up.
Important points when using the printer mode
•Make sure that the tray's paper size setting is the same as the tray's
A3 paper size setting in the printer driver. For example, if the tray's paper
ENTER A4 size setting is A4R, set "Setting Paper Size" to "A4-R". For more
A4
A5 information, see "CONFIGURING THE PRINTER DRIVER" in the
B4
TRA "Software Setup Guide".

AR-5316/5320 UNPACKING AND INSTALLATION 5-1

[07]SIMULATIONS.fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２６分

[7] SIMULATIONS Main Sub

Contents
code code
22 15 Trouble memory display
1. Entering the simulation mode 17 Copy counter display
Perform the following procedure to enter the simulation mode. 18 Printer counter display
"#" key Interrupt key "C" key Interrupt key 21 Scanner counter display
Main code Start key Sub code Start key 22 SPF jam counter display
24 01 Jam total counter clear
02 Trouble memory clear
2. Canceling the simulation mode
04 SPF counter clear
When the clear all key is pressed, the simulation mode is cancelled. 06 Paper feed counter clear
When the interruption key is pressed, the process is interrupted and the 07 Drum counter clear
screen returns to the sub code entering display.
08 Copy counter clear
* After canceling the simulation mode, be sure to turn OFF/ON the
09 Printer counter clear
power and check the operation.
13 Scanner counter clear
14 SPF jam total counter clear
Note: If the machine is terminated by a jam error or paper empty during
copying in the adjustment by the simulation, recopying is required. 25 01 Main motor operation check
10 Polygon motor operation check
26 02 Size setting
3. List of simulations 03 Auditor setting
Main Sub 05 Count mode setting
Contents
code code 06 Destination setting
01 01 Mirror scanning operation 07 Machine condition check (CPM)
02 Mirror home position sensor (MHPS) status display 18 Toner save mode setting
06 Mirror scanning operation aging 30 CE mark conformity control ON/OFF
02 01 Single paper feeder (SPF) aging 31 Auditor mode exclusive setup
02 SPF sensor status display 36 Cancel of stop at maintenance life over
03 SPF motor operation check 37 Cancel of stop at developer life over
08 SPG paper feed solenoid operation check 38 Cancel of stop at drum life over
11 SPF PS release solenoid operation check 39 Memory capacity check
05 01 Operation panel display check 42 Transfer ON/OFF timing control setting
02 Fusing lamp and cooling fan operation check 43 Side void amount setting
03 Copy lamp lighting check 51 Copy temporary stop function setting
06 01 Paper feed solenoid operation check 30 01 Paper sensor status display
02 Resist roller solenoid operation check 42 01 Developing counter clear
10 Cassette semi-circular roller cleaning 43 01 Fusing temperature setting
07 01 Warm-up display and aging with jam 12 Standby mode fusing fan rotation setting
06 Intermittent aging 13 Fusing paper interval control allow/inhibit setting
08 Shifting with warm-up display 44 34 Transfer current setting
08 01 Developing bias output 40 Setting of rotation time before toner supply
02 Main charger output (Grid = HIGH) 46 01 Copy density adjustment (300dpi)
03 Main charger output (Grid = LOW) 02 Copy density adjustment (600dpi)
06 Transfer charger output 09 Copy exposure level adjustment, individual setting
10 - Toner motor operation (Text) 300dpi
14 - Trouble cancel (except for U2) 10 Copy exposure level adjustment, individual setting
16 - U2 trouble cancel (Text) 600dpi
20 01 Maintenance counter clear 11 Copy exposure level adjustment, individual setting
21 01 Maintenance cycle setting (Photo) 600dpi
02 Mini maintenance cycle setting 18 Image contrast adjustment (300dpi)
22 01 Maintenance counter display 19 Exposure mode setting
(Gamma table setting/AE operation mode setting/
02 Maintenance preset display
Photo image process setting)
03 Jam memory display
20 SPF exposure correction
04 Jam total counter display
29 Image contrast adjustment (600dpi)
05 Total counter display
30 AE limit setting
06 Developing counter display
31 Image sharpness adjustment
07 Mini maintenance preset display
48 01 Main scanning magnification ratio adjustment
08 SPF counter display
05 SPF/RSPF mode sub scanning magnification ratio
09 Paper feed counter display adjustment in copying
12 Drum counter display 49 01 Flash ROM program writing mode
13 CRUM type display 12 Standby mode fusing fan RPM setting
14 P-ROM version display

AR-5316/5320 SIMULATIONS 7-1

[07]SIMULATIONS.fm 2 ページ ２００３年１２月１９日　金曜日　午後３時２６分

Main Sub
Contents
code code
50 01 Image lead edge adjustment
06 Copy lead edge position adjustment (SPF/RSPF)
10 Paper off-center adjustment
12 Document off-center adjustment
51 02 Resist amount adjustment
53 08 SPF scanning position automatic adjustment
10 SPF scan position change-over setting
61 03 HSYNC output check
63 01 Shading check
07 SPF automatic correction
64 01 Self print

4. Contents of simulations
Main Sub
Contents Details of operation
code code
01 06 Mirror scanning operation aging When the [START] key is pressed, the mirror base performs A3 full scanning at the set magnification
ratio speed. During scanning, the set magnification ratio is displayed. After 3 seconds, the mirror
base performs full scanning again. During scanning, the set magnification ratio is displayed.
* When the [START] key is pressed again, the ready lamp turns and remains off.
The DV replacement/OPC drum cartridge replacement lamp displays the status of the mirror
home position sensor. (The lamp lights up when the mirror is in the home position.)
During aging, the copy lamp lights up. When the [Interrupt] key is pressed, the operation is
interrupted if operating, and the machine goes into the sub code input standby mode.
02 01 Single paper feeder (SPF) aging When the [START] key is pressed, the set magnification ratio is acquired and document transport
operation of single surface is performed in the case of SPF or document transport operation of
duplex surfaces is performed. During operation, the LED on the display section corresponding to the
selected magnification ratio lights up, and the magnification ratio is displayed on the 7-seg display.
When the [Interrupt] key is pressed at that time, the machine goes to the sub code input standby
mode. When the [CA] key is pressed, the simulation is terminated.
02 SPF sensor status display (In order to receive the sensor change notification, the load must be decreased.)
The sensor status (ON/OFF) in the SPF can be checked with the following lamps.
When a sensor detects paper, it turns on. The open/close detection sensor turns on when the
machine is opened.
Display lamp Sensor
Toner supply lamp SPF document set sensor
Copier jam lamp SPF document transport sensor
The DV replacement/OPC drum cartridge SPF unit (OC cover) open/close sensor
replacement lamp
Paper empty lamp SPF paper exit sensor
SPF jam lamp SPF paper feed cover open/close sensor
Manual paper feed lamp SPF paper length sensor 1
Tray jam lamp SPF paper length sensor 2
AE lamp SPF paper feed width sensor (small)
TEXT lamp SPF paper feed width sensor (middle)
PHOTO lamp SPF paper feed width sensor (large)
When the [Interrupt] key is pressed, the machine goes to the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
06 01 Paper feed solenoid operation When this simulation is executed, the sub code is displayed on the 7-seg LED and the lamp
check corresponding to the solenoid lights up.
Select a solenoid with the tray select key (the lamp corresponding to the solenoid lights up) and
press the [START] key, and the machine repeats operation of ON for 500ms and OFF for 500ms.
This operation is repeated 20 times.
After that, the machine goes into the sub code entry standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
Display lamp Solenoid
Main cassette lamp Main cassette paper feed solenoid
2nd cassette lamp * 2nd cassette paper feed solenoid
Manual paper feed lamp Manual paper feed solenoid
2nd cassette jam lamp * 2nd cassette paper transport solenoid
Machine jam lamp & 2nd cassette jam lamp * 3rd cassette transport solenoid

* Supported for the installed models only. Skipped for the models without installation.

AR-5316/5320 SIMULATIONS 7-2

[07]SIMULATIONS.fm 3 ページ ２００３年１２月１９日　金曜日　午後３時２６分

Main Sub
Contents Details of operation
code code
06 02 Resist roller solenoid operation When the [START] key is pressed in the sub code input state, the resist solenoid (RRS) turns ON for
check 500ms and OFF for 500ms. This operation is repeated 20 times.
After completion of the process, the machine goes into the sub code input standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
10 Cassette semi-circular roller First of all, remove the developer unit.
cleaning Enter the simulation code, specify the cassette to be cleaned with the tray select key, and press
START button. The main motor rotates to move the cassette semi-circular roller by half circle and
make the roller face downward.
After completion of cleaning, when INTERRUPT key is pressed, the machine goes into the sub code
entry standby mode and the roller returns to the original positions.
To clean another roller continuously, press INTERRUPT key to return the roller to the original
position, and execute the simulation again.
During the operation, the sub code is displayed on the display.
* When CA key is pressed, the simulation mode is terminated.
However, the roller returns to the original position by the initial operation.
08 01 Developing bias output When the [START] key is pressed, the developing bias signal is turned ON for 30 sec.
However, to calculate the actual output value is calculated, execute SIM25-01.
After completion of the process, the machine goes into the sub code input standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
02 Main charger output (Grid = HIGH) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
HIGH mode. After completion of the process, the machine goes into the sub code input standby
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
03 Main charger output (Grid = LOW) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
LOW mode. After completion of the process, the machine goes into the sub code input standby
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
06 Transfer charger output Select an output mode with the [Mode select] key and press the [START] key. The transfer charger
output is delivered for 30 sec in the selected mode.
After 30 sec of transfer charger output, the machine goes into the sub code entry standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
Display lamp Output mode
AE mode lamp Normal size width: Front surface
AE mode lamp & PHOTO mode lamp Small size width: Front surface
AE & TEXT & PHOTO mode lamp Manual paper feed mode

•Small size is Letter R (A4R) or smaller.

22 01 Maintenance counter display The maintenance counter value is displayed. (Alternate display by 3 digits)
04 Jam total counter display The jam total counter value is displayed. (Alternate display by 3 digits)
05 Total counter display The total counter value is displayed. (Alternate display by 3 digits)
06 Developing counter display The developing counter data is acquired and displayed on the 7-seg display. (Alternate display by 3
digits)
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
08 SPF counter display The SPF counter value is displayed. (Alternate display by 3 digits)
14 P-ROM version display The P-ROM version is displayed on the copy quantity display. The main code and the sub code are
alternatively displayed by 2 digits. The display interval is same as that of the counter display.
By pressing the fixed magnification ratio key, each version display is switched.
Display lamp (AB series) Display lamp (Inch series) Displayed version
141% 141% Machine program
17 Copy counter display The copy counter value is displayed. (Alternate display by 3 digits) When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
18 Printer counter display The printer counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
21 Scanner counter display The scanner counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.

AR-5316/5320 SIMULATIONS 7-3

[07]SIMULATIONS.fm 4 ページ ２００３年１２月１９日　金曜日　午後３時２６分

Main Sub
Contents Details of operation
code code
22 22 SPF jam counter display The SPF jam counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
44 34 Transfer current setting Used to set the transfer current for the front surface and that for the back surface. When this
simulation is executed, the current set value is displayed on the 7-seg display. Select the set value
with the zoom (Up/Down) keys and press the [START] key, and the set content is written into the
EEPROM and the machine goes into the sub code input standby mode. Press the [Mode select] key
to select each setting mode. At that time, the setup content is written into the EEPROM.
The set range is 90uA ~ 360uA in the increment of 10uA.
Display lamp Setting mode
AE mode lamp Normal size width: Front
AE mode lamp & PHOTO mode lamp Small size width: Front
AE & TEXT & PHOTO mode lamps Manual paper feed
* Small size paper must be Letter R (A4R) or smaller.
* For the special size of tray, use the normal size width.
49 01 Flash ROM program writing mode (Operating procedure)
When this simulation is executed, "d" is displayed on the copy quantity display and the machine
enters the Flash ROM program writing mode. Use the writing tool on the PC to write the program.
During writing, the display is made as follows. After completion of downloading, turn OFF/ON the
power to reset.
Status Copy quantity display Pre-heat lamp Ready lamp
Download data reception "d" ON OFF
Data delete start "d" ON ON
Data writing (Boot section) "d" Flash OFF
Data writing (Program section) "d" Flash Flash
Sum check "d" ON ON
Completion of downloading "OFF" OFF OFF
Error status "*E" OFF OFF

* "*" in the error display indicates the error position.

00 Data receive error 07 Sum check error (Program section)
02 FLASH ROM delete error 08 Sum check error (EEPROM section)
03 FLASH ROM write error (Boot section) 09 E2PROM verify error
04 FLASH ROM write error (Program section) 0b E2PROM verify error
05 Sum check error (Loader section) 0F Download data length error
06 Sum check error (Boot section)
12 Standby mode fusing fan RPM When this simulation is executed, the currently set code number is displayed.
setting When [MODE SELECT] key is pressed, the normal setting and the high fusing temperature setting
are switched alternatively.
Enter the code number and press START key, and the number is written into the EEPROM and the
machine goes into the sub code entry standby mode.
Display lamp Setting mode Default
AE mode lamp Normal temperature control (190°C or less) Low speed rotation
TEXT mode Fusing temperature of 190°C or above High speed rotation

Code number Setting

0 Low speed rotation
1 High speed rotation

AR-5316/5320 SIMULATIONS 7-4

[07]SIMULATIONS.fm 5 ページ ２００３年１２月１９日　金曜日　午後３時２６分

Main Sub
Contents Details of operation
code code
51 02 Resist amount adjustment Used to adjust the contact pressure of the machine resist roller and the RSPF resist roller onto the
paper.
(Operating procedure)
When this simulation is executed, the current set value is displayed.
When the exposure mode key is pressed, the following set items are changed sequentially. Enter an
adjustment value with the 10-key and press the [START] key, and the entered value will be saved and
a copy will be made. (Adjustment range: 1 ~ 99, Default: 50)
When the [CA] key is pressed, the entered value is saved and the simulation is terminated.
Lighting lamp Adjustment mode
AE, Main cassette lamp Main cassette paper feed
AE, 2nd cassette lamp 2nd cassette paper feed
AE, Manual paper feed lamp Manual paper feed
AE, TEXT, PHOTO lamps SPF document feed (Front surface)

Supported for the installed models only. Skipped for the models without installation.
53 10 SPF scan position change-over Used to change over the scan position depending on that the SPF unit and the SPF document glass
setting holder section are of anti-dirt glass or not.
When this simulation is executed, the currently set code number is displayed.
Enter the code number corresponding to the SPF unit to be used and press [START] key, and the
setting will be changed over.
Code No. Mode
0 Set to the scan position of the current mass production SPF unit. (Default)
1 Set to the scan position of the ant-dirt SPF unit.
Though this setting is changed, the other set values are not affected. (The other set values remain
unchanged.)
When replacing and installing the SPF unit, it is recommendable to use this simulation to set the
scan position and execute the scan position automatic adjustment.
64 01 Self print The optical system status is ignored and a self print is made. Also when a print command is sent
from the host, printing is performed.
(Operating procedure)
When this simulation is executed, warm-up is performed and the ready lamp is lighted.
(However, the scanner is invalid and no initial operation is made.)
Enter the code number with the 10-key, and select a cassette with the cassette select key and press
the [START] key. The selected cassette start paper feed and printing is performed in the selected
pattern.
* Only the tray lamp and the online lamp are lighted, and no other lamps are lighted.
Printing is made in 1 by 2 mode, where one line is printed and the following two liens are not printed,
or in the grid pattern.
Code number Pattern
0 1 by 2
1 Grid pattern
2 White paper
3 Black background

* Input disable for 4 ~ 99

* Print data are made on A3 size. (A3 paper is preferable.)

AR-5316/5320 SIMULATIONS 7-5

[08]USERPROGRAMS.fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２７分

[8] USER PROGRAMS

The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.

1. List of user programs

This copier has the following user programs.
Program
Program name Description Default Parameters
No
Auto clear time "Auto clear time" automatically returns the copy settings to the initial 1 (OFF)
settings when a certain period of time elapses after a copy is made. 2 (10sec)
This program is used to select the period of time. "Auto clear time"
3 (20sec)
1 can also be disabled. 60sec
4 (60sec)
5 (90sec)
6 (120sec)
Preheat mode This function automatically switches the machine to a low power 1 (1min)
consumption state if the set duration of time elapses without the 2 (5min)
machine being used when the power is on.
3 (30min)
2 The POWER SAVE indicator lights up, however, the keys on the 1min
operation panel can be used. Normal operation automatically 4 (60min)
resumes when a key on the operation panel is pressed, a print job is 5 (120min)
received or an original is placed. 6 (240min)
Auto power shut-off timer This function automatically switches the machine to a state that 1 (5min)
consumes even less power than preheat mode if the set duration of 2 (30min)
time elapses without the machine being used when the power is on.
3 (60min)
All lights except the POWER SAVE indicator and ON LINE indicator
3 5min 4 (120min)
go off. To resume normal operation, press the [START] key. Normal
operation also resumes automatically when a print job is received or 5 (240min)
scanning is begun from a computer. While in auto power shut-off
mode, no keys (except the [START] key) can be used.
Stream feeding mode *1 When copying using the SPF, during the period of time that the SPF 0 (OFF)
indicator blinks after an original has been scanned (about 5 1 (ON)
4 OFF
seconds), a subsequent original can be placed and automatically
fed into the machine.
Auto power shut-off Use this setting to enable or disable auto power shut-off. 0 (OFF)
5 ON
setting 1 (ON)
Auto paper select mode *2 This function automatically selects paper that is the same size as 0 (OFF)
8 the original placed in the SPF, or the same size as that selected with ON 1 (ON)
the [ORIGINAL SIZE ENTER] key. The function can be disabled.
Auto tray switching *2 If the paper runs out during printing and there is paper of the same 0 (OFF)
size and orientation in another tray, this function automatically 1 (ON)
9 ON
switches to that tray (excluding the bypass tray). The function can be
disabled.
Auditing mode Use to enable or disable "Auditing mode". 0 (OFF)
10 "Auditing mode" is initially disabled. OFF
1 (ON)
Account number entry Use to set up account numbers.
11 - -
Up to 20 accounts can be established.
Account number change 12 Use to change an account number. - -
Account number deletion Use to delete an account number. Delete 0 (Delete single account)
13 A single account number can be deleted, or all account numbers at single 1 (Delete all accounts)
once. account
Number of copies per This displays the number of copies made by each account.
account 14 The maximum count is 49,999. If this number is exceeded, the count - -
will start over from 0.
Resetting account Use to reset the copy count of an account to 0. Reset single 0 (Reset single account)
15 The copy count of a single account or of all accounts can be reset. account 1 (Reset all accounts)
Resolution in Auto/Text This setting is used to change the copy resolution in AUTO and 1 (300dpi)
mode TEXT mode from 600 x 300 dpi to 600 x 600 dpi 2 (600dpi)
23 300dpi
(high-quality mode).
Scanning is slower when high-quality mode is used.

*1 On models with a SPF.

*2 On model with the two trays.

AR-5316/5320 USER PROGRAMS 8-1

[08]USERPROGRAMS.fm 2 ページ ２００３年１２月１９日　金曜日　午後３時２７分

Program
Program name Description Default Parameters
No
Key auto repeat Use this setting to select whether or not holding down a key causes 0 (OFF)
repeated input of the key. For keys that normally cause a set value to 1 (ON)
25 increase when held down (for example, holding down the [ZOOM] ON
key), this program can be used to have the set value not change
when the key is held down.
Key press time Use this setting to select how long a key must be pressed for the 1 (Minimum
input to be accepted. By selecting a longer time, you can prevent (current response speed))
Minimum
settings from being changed by the accidental pressing of a key. (current 2 (0.5sec)
26
response 3 (1.0sec)
speed) 4 (1.5sec)
5 (2.0sec)
Audible signals volume This sets the volume of beep signals. 1 (short beep)
27 short beep 2 (long beep)
3 (OFF)
Base setting beep signal Use this to sound a beep when a base setting is selected. 0 (OFF)
28 OFF
1 (ON)
Number of copies limit Use this setting to select 99 or 999 for the maximum number of 1 (99 copies)
29 999 copies
copies. 2 (999 copies)
Use close paper size When this function is enabled, printing in printer mode will 0 (OFF)
automatically continue using a different size of paper if the specified 1 (ON)
30 OFF
size of paper runs out in all trays. This feature does not function in
copy mode.
Default tray setting Use this program to select a default tray. This tray is automatically 1 (Upper paper tray)
selected each time the power is turned on or each time the machine Upper
31 2 (Lower paper tray)
reverts to the initial settings. paper tray
5 (Bypass tray)
Default exposure mode Use this program to set "AUTO", "TEXT", or "PHOTO" as the default 1 (AUTO)
32 exposure mode. AUTO 2 (TEXT)
3 (PHOTO)

AR-5316/5320 USER PROGRAMS 8-2

[10]MAINTENANCE.fm 1 ページ ２００４年１月１９日　月曜日　午後１時５２分

[10] MAINTENANCE
1. Maintenance table
X:Check(Clean, adjust, or replace when required.) O:Clean :Replace :Adjust :Lubricate
Unit name Part name When calling 50K 100K 150K
Drum peripheral OPC drum -
Cleaning blade -
Side seal F/R X X X X
MC unit X
(MC charging electrode) - ( ) ( ) ( )
(MC grid) - ( ) ( ) ( )
(MC case) - ( ) ( ) ( )
Transfer wire O O O O
Transfer paper guide O O O O
MC guide sheet (Cleaning blade attached) -
Drum fixing plate B X
Process frame unit X X X
Discharge holder O O O O
Separation pawl
Only for Viet Nam X
Star ring x 2 pcs
Developing section Developer -
DV seal - X X
DV under seal - - -
DV side seal - X X
Side Mylar - - -
Optical section Lamp unit Reflector O O O O
Mirror O O O O
No.2/3 mirror unit Mirror O O O O
Pulley X X X X
CCD peripheral Lens O O O O
Glass Table glass O O O O
White Plate O O O O
Other Drive wire X X X X
Rail X X X X
Document cover O O O O
Document size sensor O O O O
LSU Dust-proof glass O O O O
Paper feed section Multi paper feed section Take-up roller(manual / SPF) O O O O
Paper feed roller O O O O
Spring clutch O O O O
Paper transport section PS roller O O O O
Transport (paper exit) rollers O O O O
Spring clutch O O O O
Fusing section Upper heat roller O O O
Pressure roller O O O O
Pressure roller bearing X X X O
Upper separation pawl X X X O
Lower separation pawl X X X O
Cleaning pad X X X
Drive section Gears X X X X
Belts X X X O
Paper exit section Ozone filter*1 X X X X

*1:Recommendable replacement time:50K(Letter,5%print)

AR-5316/5320 MAINTENANCE 10-1

[10]MAINTENANCE.fm 2 ページ ２００３年１２月１９日　金曜日　午後３時２７分

2. Maintenance display system C. DV seal attachment procedure

Toner Life, 16K
Remaining a. Press and hold the density adjustment
quantity LIGHT key for more than 5 sec, and the
check *1 machine will enter the user program
mode.
b. Press and hold the "%" key for more
than 5 sec, and the remaining quantity
will be displayed on the copy quantity
display in one of the following levels:
(Remaining quantity display levels:
100%, 75%, 50%, 25%, 10%, LO)
c. Press the density adjustment LIGHT 1) When attaching the DV side Mylar, check the position shown in the
key to cancel. figure below and attach it properly.
Remaining NEAR EMPTY EMPTY
quantity About 10%
LED ON Flash
Machine Operation allowed Stop
Developer Life 50K
LED ON at 50K of the
developer count
Machine Selection is available between Not Stop
and Stop by Service Simulation (SIM 26-
37) Setup.
(If Stop is selected, the LED will flash and
stop at 50K.) 2) When attaching the DV side sheet, check the position shown in the
* Default: Not Stop
figure below and attach it properly.
* Clear: SIM 42-1
(First of all, attach the DV side Mylar.)
Maintenance LED Selection is available among 50K, 25K,
10K, 7.5K, 5K, and free (no lighting) with
SIM 21-1.
* Default: 50K
* Clear: SIM 20-1
Machine Not stop

*1: Installation of a new toner cartridge allows to display the remaining

quantity.

3. Note for replacement of consumable parts

A. Toner cartridge * Be sure to attach the DV side sheet so that the notch is on the
outside.
When a waste toner cartridge is removed from the machine, it must be
put in a polyethylene bag to avoid scattering of toner.

B. DV cartridge
Do not shake or put up the developer cartridge. Otherwise developer
may scatter.

AR-5316/5320 MAINTENANCE 10-2

 Scanner Unit SPF
CCFL SPF Driver
CCD PWB MOTOR
5V A5V 3.3V
SPMT0/1/2/3
Lamp
B/W AFE(AD9826) SPFCLH,
Inverter SPFGSOL
CCD C A M Driver
SPFPSOL,
(TCD1710) D G P AD 8bits(MSB/LSB) SPFRSOL
S C X 24V
16bit /SPFCOVER,
HOME
5V s PAPER, Sensor
POSITION SPFOPEN,
SENSOR /SPFOUT
CCD Driver
ADCCLK,SYNCH,
BSAMP,VSAMP L1,2 Selector 1. Block diagram
SDI,SCLK,LOAD,OBE W0,1,2,3
MODE
LVTTL
I/F PWB
I MCU-PWB 5V,3.3V MHPS
E
E PWM
E 3.3V CLON
1
2
8 LVC1284 IEEE 1284 I/F
[13] ELECTRICAL SECTION

U PDIUSBP11AD USB I/F

S Zebra2 ASIC
B
1 Printer CLK(20.3094MHz) (296pin) Software Reset
. 3.3V
1 RIC
Download Scanner CLK(48MHz) Reset IC
UART
2nd CASSETTE
CPU FSOL Feed SOL , Pick up SOL
SDRAM H8S/2320 CASSETTE DETECTION,
PSOL
Simp 16Mbyte (19.6608MHz)
A[19...1] Y1 PAPER DETECTION,
OP-CLK SELIN1,2,3 PAPER PASS DETECTION,
[13]ELECTRICALSECTION.fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２７分

D[15...0] OP-LATCH DOOR DETECTION

OP-DATA
1Mb(1Mb*1) SELIN1,2,3 OPU PWB
SRAM OP-BEO
KIN1
Flash ROM 5V
SCAN1-6
PSW
8Mbit 7seg LED
PSL,ONL
LC7935AN
I2C Bus LED

AR-5316/5320 ELECTRICAL SECTION 13-1

LCX16374
5V
SSCG
4Kbyte
HC151 EEPROM CRUM
HC151 KEY

/MMD
TM+,TM-
CPU CLK(19.6608MHz)

MM_AI0/AI1/PH_A
MM_BI0/BI1/PH_B
START KEY

PMD
PMCLK(2078.74(Hz))

/MMRDY
Driver Driver
LED

Other Loads /VIDEO

S/H Light only
MPFS,RRS, APCSTT POWER SUPPLY HVU COIN VENDOR/AUDITOR
SGS,SRRC,SPUS,SPPS, Main Motor Toner Motor Mirror Motor /SYNC
/CV_COPY
VFMCNT,VFM,MPFS,CPFS2, /POFF,HL,PR TC,GRID,MC, /CV_COUNT, /CV_START, /CV_C
CPFS1 LSU FW BIAS
A,
3.3V,5VEN,5V,24V
/CV_DPX, /CV_SIZE0, 1, 2, 3
Polygon
Motor
Other Inputs FAN

CPU INTERRUPT
SPPD
CPU I/O
RTH DRST
 * (O) Normal Open :Low GP1S58(O)
(C) Normal Close :High
OPTICAL BASE PLATE
LSU POLYGON
OPERETION PANEL Mirror MOTOR MOTOR
CCD PWB Mirror HP
SENSOR APC-PWB
COPY LAMP

24C
COPY OP PWB GP1S58(C)

(BLACK)
BD-PWB

IMSA-9610S-
ACTUAL WIRING DIAGRAM 1/7

FFC

FFC
SHIFTER

FFC
3
I/F USB1.1
MOTOR SPF UN
3. Actual wiring diagram

GP1A71A1(O) SPF GROUND WIRE

SHIFTER HP ORIGINAL TRAY HARNESS FFC
SENSOR HARNESS
SENSOR

(WHITE)
IEEE1284

(WHITE)
(WHITE)

13FE-BT-VK-N
COOLING FFC

(BLACK)

13FE-BT-VK-N
24FMN-BTRK-A
35FE-BT-VK-N

FUN
COOLING B3B-PH-K-R
B4B-PH-K-S SUB-D 25 (RED) MCFB
FUN
(WHITE)
04FE-BT-VK-N FE4-32-S1505 MC GRID
MODEL WITH SHIFTER (WHITE) (BLACK)

PAPER OUT
COOLING SENSOR

(WHITE)
FUN MCU-PWB

(WHITE)

B6B-PH-K-S
B3B-PH-K-SX
COOLING DUP
FUN SENSOR 35FE-BT-VK-N HVU
Option (WHITE)
[13]ELECTRICALSECTION.fm 2 ページ ２００３年１２月１９日　金曜日　午後３時２７分

TC
B20B-PHDSS-B
MODEL W/O SHIFTER (WHITE)
(RED)

B2B-XH-A-BK
(BLACK)
B7B-PH-K-S

B2B-XH-A-S
Bias
BC
DRUM INISAL SW B3B-PH-K-S (WHITE)

B3B-PH-K-BK
(BLACK)
(WHITE) B3B-PH-K-R B12B-PHDSS-B
FUSER 08FE-BT-VK-N B2P-VH B3P-VH B3B-PH-K-BK (RED) (WHITE)
(BLACK)

(WHITE)
(WHITE) (WHITE) (WHITE)

B3B-PH-K-S
POWER PWB
THERMISTER B2B-XH-A-R B26B-PHDSS-B
B4B-PH-K-S (RED) B4B-PH-K-R (WHITE)
B4B-PH-K-S B4B-PH-K-BL (WHITE) (RED)
(BLACK)

FFC
(WHITE)

AR-5316/5320 ELECTRICAL SECTION 13-2

HEATER LAMP AC SW
(WHITE)

B03P-VL
B18B-PHDSS-B

(WHITE)
PICK UP SOL
AC Cord
HAND PAPER PICK MAIN TONER
UP SOLENOID MOTOR MOTOR CASETTE SWITCH B4B-PH-K-S B3B-PH-K-S 3P TERMINAL
PS SOL (WHITE) (WHITE) 230V ONLY
SENSOR

PAPER IN
SENSOR
CASETTE EMPTY
SRU DEV UN SENSOR 2nd CASETTE
HAND PAPER EMPTY COOLING FUN
SENSOR
Front Cover SW
230V ONLY
REACTOL
Side Cover SW
[14]LeadFree.fm 1 ページ ２００３年１２月１９日　金曜日　午後３時２８分

LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.

Example:

<Solder composition code of lead-free solder>

Solder composition Solder composition Solder composition code

code (Refer to the Sn-Ag-Cu a
Lead-Free table at the right.)
Sn-Ag-Bi
b
Sn-Ag-Bi-Cu
Sn-Zn-Bi z
5mm
a Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
n
i

s
Bi-Sn-Ag-P p
Bi-Sn-Ag

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use
soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is
inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed
the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is
confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after
completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
[00]COVER.fm 2 ページ ２００３年１２月１９日　金曜日　午後３時２５分

COPYRIGHT c 2003 BY SHARP CORPORATION

All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.

Trademark acknowledgments
Windows and Windows NT are trademarks of Microsoft Corporation in the U.S.A.
and other countries.
IBM and PC/AT are trademarks of International Business Machines Corporation.
PCL is a trademark of Hewlett-Packard Company.
Pentium is a registered trademark of Intel Corporation.
All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATION
Digital Document System Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2003 Dec. Printed in Japan N