BY CHRISTOPHER F.

SIKORA

TRODUCTION

Copyright 2015 Christopher Sikora

This manual is for educational purposes only. It may be printed, but not resold for profit for its content.
Creo Parametric 3.0 is a registered trademark of PTC Corporation.
Creo Parametric 3.0 is a product name of PTC Corporation.
ACIS is a registered trademark of Spatial Technology Inc.
IGES Access Library is a trademark of IGES Data Analysis, Inc.

Other brand or product names are trademarks or registered trademarks of their respective holders.

The information discussed in this document is subject to change without notice and should not be considered commitments by
Christopher F. Sikora.
The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms
of the manufacturer license.

Pro/ENGINEER (Creo 3.0) Basics 105

Course Description:
Pro/ENGINEER (Creo) Basics
3 credit hours
Exploration of the theory and application of solid modeling techniques for product
design and manufacturing. Prerequisite: Intro to Engineering Drawings 101 or consent of
instructor.
Course Objectives:
Provide the student with the knowledge and practical experience in the areas of 3D CAD
modeling of parts, assemblies, and the creation of mechanical drawings from the
models.
Textbook
Creo Basics free/pdf., parts, and videos provided on www.vertanux1.com
Evaluation Scale:
A

90% to 100%

80% to 89%

70% to 79%

60% to 69%

Below 60%

Points:
Exercises

300 pts

Mid Term

300 pts

Final

300 pts

Labs

100 pts

Total

1000 pts

General Course Outline

Date

Week Topic
1.

Introduction to the Interface Lecture

Modeling Theory - Sketching and Base Feature Geometry Creation. Lab

2.

Revolved Features and Mirroring

3.

Part Modeling
Secondary Features. Fillets, Chamfers, Draft, Patterns, Mirroring.

4.

Sweeps, and Circular Patterns

5.

Modeling Quiz and CAD Administration

6.

Building Assemblies (Bottom-Up method BU)

7.

Creating Drawings. Review for Mid Term

8.

Mid Term Exam

9.

3D Curves and Sweeps

10.

Swept Blends/Lofting

11.

Assemblies Creation (Top-Down Method TD)

12.

Assembly/Part Editing (TD & BU Methods)

13.

Sheet Metal Intro

14.

Assembly Project (continued)

15.

Lab time to complete exercise, Review for Final Exam

16.

Final Exam

Required Hardware
16+ Gigabyte USB Flash / Thumb Drive

Required Software (Click on link below)

CREO 3.0 Educational Edition

STUDENTS WITH DISABILITIES

We welcome students with disabilities and are committed to supporting them as they
attend college. If a student has a disability (visual, aural, speech, emotional/psychiatric,
orthopedic, health, or learning), s/he may be entitled to some accommodation, service,
or support. While the College will not compromise or waive essential skill requirements
in any course or degree, students with disabilities may be supported with
accommodations to help meet these requirements.
The laws in effect at college level state that a person does not have to reveal a disability,
but if support is needed, documentation of the disability must be provided. If none is
provided, the college does not have to make any exceptions to standard procedures.
All students are expected to comply with the Student Code of Conduct and all other
college procedures as stated in the current College Catalog.
PROCEDURE FOR REQUESTING ACCOMMODATIONS:
1. Go to SRC108 and sign release to have documentation sent to the college, or bring in
documentation.
2. Attend an appointment that will be arranged for you with the ADA coordinator or
designee.
CLASSROOM PROCEDURES:
1. Attendance of each scheduled class meeting is required unless otherwise specified by
the instructor.
2. Daily work problems and hand-outs will be maintained in a notebook and turned in
upon the instructors request.
3. Reading assignments will be made prior to discussing the material.
4. Keep your drafting workstation clean and free of miscellaneous materials.
5. Please report any malfunctioning equipment to the instructor.
LABORATORY UTILIZATION:
1. Regular daytime hours. The room is open for your use starting at 8:00AM daily. Even
though classes are being held, you are encouraged to find an open area and
work in the laboratory.
2. There are evening classes, but you may use the lab up to 10:00PM.
3. On weekends, the lab will be available on Saturdays from 9:00AM to 4:00PM. The
lab will be closed on Sundays.
INSTRUCTORS RESPONSIBILITY:
1. Present material in a manner that can be understood by each student.
2. Respect each student as an individual, to be of assistance in any way possible, and to
help solve problems, but not to solve problems for the student.

3. Keep records of your progress and to summarize your learning experiences with a
final
Attendance and Cheating Policies
Introduction: Drafting is a technical profession in our society; consequently,
presentations in this course are factual and technical, and final grades represent the
students accomplishment of the learning activities.
Attendance: Attendance at each class meeting is required. Attendance may be a factor
when determining the final grade. Your instructor will specify his/her policy concerning
the relationship of attendance and the final grade.
Each instructor has the option of taking attendance for his/her personal use. If a
student misses class because of illness, a field trip, or any other AUTHORIZED reason,
the student is obligated to determine what was missed, and will be held responsible for
that work. If a student is absent without an excused absence, he/she will also be held
responsible, and must obtain all information from some source other than the class
instructor. Instructors DO NOT have to accept any
make-up work, do individual tutoring, or make special test arrangements for any
UNEXCUSED ABSENCE.
Cheating: Cheating in this department is interpreted to mean the copying, tracing, or
use of another persons work for the purpose of completing an assignment.
Individual initiative and personal performance in completing all assignments is required
of all students. This course may seem to offer situations that are conducive to cheating.
However, evidence of cheating on the part of any student will be sufficient cause for an
assignment of an F for the course.
Instructors reserve the right to change a grade after the end of the semester if there is
evidence to warrants.
CAD 105 EXERCISES & VIDEOS INDEX

1.

27:32

E1 CREO Parametric 2.0

Exercise 1 - Introduction to sketching, modeling and options menu inside Creo 2.0, Also, basic rendering
tools.

2.

18:46

E2 CREO Parametric 2.0

Exercise 2 - Introduction to Sketch Mirroring, and Revolved features inside Creo 2.0

3.

36:30

E3 CREO Parametric 2.0

Exercise 3 - Secondary feature modeling, Extrusions with (new) taper/draft function. offset datum planes,
extrude up to next, engraved text.

4.

16:38

E4 CREO Parametric 2.0

Exercise 4 - Introduction to sweeps, revolved features, filleting, circular patterns.

5.

21:14

E5 CREO Parametric 2.0 (new)

Exercise 5 - Bottom-up assembly creation

6.

12:28

E6 CREO Parametric 2.0

Exercise 6 - Introduction to 2D Drawings, Detailing, Layout, Section, Detail, Auxiliary views, Dimensioning.

7.

19:19

E7 CREO Parametric 2.0

Exercise 7 - Creating 3D Guide Curves/Path, Sweeps, Mirroring features

8.

16:03

E8 CREO Parametric 2.0

Exercise 8 - Swept Blends, Mirroring, using Sketch Splines to create a boat hull sections. Download the
free training manual at www.vertanux1.com

9.

18:56

E9 CREO Parametric 2.0

Exercise 9 - Introduction to Top-Down Assembly Modeling

10.

18:48

E10 CREO Parametric 2.0

Exercise 10 - Top-Down Assembly Modeling

11.

7:56

E11 CREO Parametric 2.0

Creo 2.0 Sheet Metal basics, Top-Down method

12.

20:40

CREO Parametric 2.0 MIDTERM REVIEW

Mid-Term Exam Review - Covers modeling parts, bottom-up assemblies, and drawing creation.

13.

27:15

CREO Parametric 2.0 FINAL EXAM REVIEW

Final Exam Review

CAD 105 TOTALS (E Exercise, L-Lab, Q-Quiz)

E1 - 10pts
o L1 10pts
o L1b 10pts

E2 30pts
o L2 5pts
o Q1 -10pts

E3 30pts
o L3 - 5pts
o L3b 5pts

E4 30pts
o L3c-5pts

E5 30pts
o L5b-10pts

E6 30pts
o L6-10pts

E7 30pts
o L3d-5pts

E8 30pts

E9 30pts
o L9 5pts

E10 30pts
o L11c - 5pts

E11 30pts
o L11d 5pts

MIDTERM 300pts
FINAL 300pts
TOTAL - 1000pts

Introduction to Pro/E - creo

creo Parametric 3.0 Interface

View Options

Ribbon Menu

Icons
Origin (Axis Center x-0, y-0, z-0)

Feature Manager

View port

Mouse Buttons
Left Button - Most commonly used for selecting objects on the screen or sketching.
Right Button Used for activating pop-up menu items, typically used when editing.
(Note: you must hold the down button for 2 seconds)
Center Button (option) Used for model rotation, dimensioning, zoom when holding
Ctrl key, and pan when holding Shift key. It also cancels commands and line chains.
Center Scroll Wheel (option) same as Center Button when depressed, only it activates
Zoom feature when scrolling wheel.

10

Options & Properties menus The heart of

creo

Selecting the File Options pull down menu (located at the top left side of the
screen) opens the active documents Options.

Model Properties

11

View options
Zoom In

Refit

Repaint

Objects

Spin Center

Shaded
Zoom Out
Create Cross-sections
for a drawing

12

Sketching
Rectangle
Circle

Line
Start Sketch
Datum Plane

Constraint/
Relations

Spline
Fillet

Arcs
3 Point
Tangent
Concentric

Apply/Finish

Trim

Point

Mirror
Dim

Text
Convert
Entities &
Offset

Cancel

NOTE: If you do not see all of these icons on your interface you can customize the toolbars to bring them
up. Right mouse button click on the top grey frame of the window and locate the customize option.

Where do you start a sketch?

Sketches can be created on any Datum Plane or Planar Face or Surface. Pro/E provides
you with three datum planes centralized at the Origin (your zero mark in space)
NOTE: Planes can also be created and will be discussed in more detail in the future. Also after completing
a sketch always select the Apply/Finish check mark on the sketch toolbar, this will activate the extrude or
revolve feature tools.

13

To start a sketch Pre-select the plane or face you desire to sketch on and then select the Sketch
Icon.
NOTE: You can select the planes from the Feature Manager.

Sketch Options

Controlling your geometry

Pro/E uses two methods for constraining geometric entities.
Constraints and Dimensions
Constraints can be referred to as common elements of geometry such as Tangency,
Parallelism, and Concentricity. These elements can be added to geometric entities
automatically or manually during the design process.
Here is an example of adding
a relationship between two
geometric entities.

14

Cautious sketching can save time.

There are 3 primary file types in Creo, which include
1. Part (.prt)
Single part or volume.
2. Assembly (.asm)
Multiple parts in one file assembled.
3. Drawing (.drw)
The 2D layout containing views, dimensions, and annotations.

Switching between documents (Activating a document)

Select the Window pull-down menu and you will see the available documents. Click on
the document you wish to work on from the list to activate it.

15

Sketch Constraints (Relations)

Constraint
Horizontal or
Vertical
Collinear
Perpendicular
Parallel

Tangent
Concentric
Midpoint
Coincident
Equal
Symmetric

Geometric entities to select Resulting Constraint

One or more lines or two or The lines become horizontal or vertical (as
more points.
defined by the current sketch space). Points are
aligned horizontally or vertically.
Two or more lines.
The items lie on the same infinite line.
Two lines.
The two items are perpendicular to each other.
Two or more lines.
The items are parallel to each other.
A line and a plane (or a
planar face) in a 3D sketch.
An arc, ellipse, or spline, and
a line or arc.
Two or more arcs, or a point
and an arc.
Two lines or a point and a
line.
A point and a line, arc, or
ellipse.
Two or more lines or two or
more arcs.
A centerline and two points,
lines, arcs, or ellipses.

The line is parallel to the selected plane.

The two items remain tangent.
The arcs share the same centerpoint.
The point remains at the midpoint of the line.
The point lies on the line, arc, or ellipse.
The line lengths or radii remain equal.
The items remain equidistant from the
centerline, on a line perpendicular to the
centerline.

16

Controlling your geometry with dimensions

Strong versus Weak
Dimensions Double click and
change to make
them Strong!

Dimensioning this way will

enable the length of the
bracket to change but the
holes will always remain
positioned to 1.5 off each
side.

Dimensioning this way will

enable the length of the
bracket to change but the
holes will always remain
positioned to the left side.

17

Solid Modeling Basics

Layer Cake method
Extruded Boss/Base (Creates/Adds material)

Extruded Cut (Removes material)

Ingredients:
Profile

Revolve method
Revolve Boss/Base (Creates/Adds material)

Revolve Cut (Removes material)

Ingredients:
Profile
Center Line (Note: The profile cannot cross over the center line!)

18

EXERCISE 1
Introduction to basic part modeling
Base Extrude Features create a 3D solid representation by extruding a 2 dimensional
profile of the entity.
Objective:
Create a
solid
model.

This will create a hole.

This will fail to extrude.

1. Start a new part

file.

4. Select the
Rectangle tool.

3. Select the
Sketch icon.

7. Click to finish
sketch.

6. Double Click
to edit the
dimensions.

2. Select the
Front plane.

5. Click and drag

across.
19

7. Select Boss
Extrude.

NOTE: When dimensioning use the dimension tool and make edge selections, mouse center button click to apply dimension.

9. Hit Apply
the green
check mark to
finish.
8. Set to Blind
@ .5.

20

10. To sketch the

next feature select
the front face of
the model and
then select the
Sketch icon.

Toggle views using

the View
Orientation
toolbar.

Adding a constraint Ctrl Select both left edges of sketch and solid. Select Coincident

21

Extrude

2. Enter .5

1. Select the
Extrude icon.

Select the face, select sketch icon and draw a circle on the face. Dimension, Hit Ok

22

Extrude Cut

4. Select the
Extrude icon.

6. Select the
Cut and
reverse options.

7. Select the Apply

or hit Enter two
times.

5. Select the
Through All
option.

Go to file save and save-as E1

Update or Regenerate model

changes using the
Regenerate button.
Although it is unnecessary in
this instance it is still a very
important tool. It will update
only dimensional or feature
changes made to the model.

Now try LAB1

NOTE: Patterns/Arrays and Mirroring will be covered in the next three chapters. Please try to model LAB 1 without using them. Its
good practice to just dimension and sketch all geometry when first starting out learning this software.

23

24

25

EXERCISE 2
Revolved Features
Revolved Feature - creates features that add or remove material by revolving one or
more profiles around a centerline. The feature can be a solid, a thin feature, or a
surface.
Tips
Profile
Centerline, Edge, or
Axis of Revolution

The profile should never cross over the centerline, nor should there be profiles on both
sides of the centerline.

26

1. Create a new part file (E2) and then start a sketch on the Front plane.

4
2. Sketch the following. Ctrl select the profile and the horizontal centerline, then
using the Mirror tool to create a of the geometry and then mirror it to the
other side. Make sure you finish adding the dimensions.

27

3. Select the Revolve feature icon.

Then select the axis/centerline.

ON
FINISH

Rounds
4. Select the top and bottom edges and add a R.100

rounds/fillets.

28

29

30

EXERCISE 3
Secondary Feature Modeling
1.

Sketch the geometry as show below on the Front plane.

DIA. 1.5
USE
TANGENT
LINES

.75
DIA. 1.2

2.

Extrude. Select Mid-Plane, 1.

FINISH
Mid-Plane

31

3.

DRAFT: Select the Draft tool, and then References, Ctrl select all side faces
of the model. Then Click on the draft hinges dialog box, and select the
Front Datum Plane.

FINISH
7

4.

Select the top surface (LMB Click 2 x) on the model and start a sketch on it.

32

5.

OFFSET: Select the Offset tool. Then select Loop. Then select the face.

6.

Enter -.125 and to flip the offset direction.

FINISH

33

7.

Select the extrude icon, and then set to cut and .125 depth.

7. Select Concentric (Circle tool), then select the arc edge of the part.

34

9. Trim the intersection.

10. Select the extrude icon, and cut .700 depth.

FINISH

35

11.

Select the base of the pocket and start a sketch. Draw the following two
.375 DIA. circles, and extrude / cut Through-all.

12.

DATUM PLANE OFFSET: Select the Top datum plane, then select the
Datum icon. Set to -4 offset.
The Datum icon
can offset as well
as several other
options for creating
planes.

36

13.

Start a sketch on DTM 1 and draw a .5 dia. circle centered on the

origin.

14.

Extrude boss and use the Up to next option.

37

15.

Select the circle and use the setting as shown in the illustration below.

FINISH

38

16.

Start a sketch on the front datum plane and draw a rectangle with the
following dimensions.

FINISH

17.

Extrude boss using the mid-plane option and .750 thick.

FINISH

39

18. Using the Draft tool select the following faces and front plane and put 7 of draft
on the side faces of the handle.

FINISH

19. Rounds: Select the rounds/fillet icon, then select the edges as shown in the
illustration below. Add .100.

40

20. Add .060 Rounds to the following edges.

FINISH

Finished

41

42

43

EXERCISE 4
Secondary Feature Modeling
1.

Sketch the geometry as show below on the Front plane. Then Trim.

8.

Revolve.

FINISH

44

9.

Constraints: Select the Front datum plane and sketch the following. Use
the Constraint tool and select the Tangent option. Then select the left
most horizontal line and the arc attached to it to establish a tangent
relationship.

10.

Sweeps: Use the pull-down menu Insert/Sweep/Protrusion Select the

left side of the curve we just created to create a new sketch datum at the
end.
Also select: SelectTraj/Curve Chain/Select All/Done/Done

11.

45

12.

Draw the following sketch and select the finish option once complete.

.5 DIA

13.

Pattern Circular Pattern: 360/3 = 120 (NOTE: First select the spoke to
activate the icon.) Select Axis also select the view axis

FINISH

46

14.

Fillet all edges at .125

FINISH

FINISH

47

15.

Select the Front plane and start a sketch on it. Rebuild after completion.

FINISH

16.

REVOLVE
FINISH

48

17.

Add .250 Rounds to the spoke handle sections.

FINISH

FINISHED

49

50

51

EXERCISE 5
Bottom-Up Assembly Creation
1.

2.

Go to File/New and select the Assembly Template.

Assembly Tools.

Assemble (Bottom-Up)
Create (Top-Down)

52

3.

To insert a part into the assembly select the Assemble icon. Select the
Sheet_Metal_Bracket.prt, and hit the open button at the bottom.

4.

Select the Automatic pull down and select the Default option.

FINISH

5.

Select the Assemble

icon and then insert the yoke_male.prt.

53

6.

Select the radial surface of the yoke_male shaft and then select the surface
of the hole on the bracket.

Notice the alignment that takes place.

54

7.

Select the Placement tab and then select New Constraint option. Then
select the top surface of the yoke_male, and the underside face of the top
flange of the bracket. Note: make sure you deselect the Allow Assumptions icon to
enable dynamic assembly motion (its located at the bottom of the Placement tab).

FINISH

8.

After applying the last constraint try moving the component using the Drag
Component icon. Click on an edge of the yoke and drag with the left mouse
button. It should spin in place only.

55

9.

Insert the spider.prt and mate the cylindrical faces of the holes.

10.

Select the side face of the spider and then the inside face of the male_yoke
leg. You may need to rotate the assembly to see the correct faces. You may
need to Regenerate after applying the last mate.

56

11.

Select the concentric holes. Select the yoke_female leg and open face of
the spider.

12.

Use the Drag Component tool to locate the yoke_female near the bottom
angled flange of the bracket.

57

13.

Editing a Mate: RMB select the Spider from the feature tree on the right of
the screen. A pull-down menu will appear. Select Edit Definition.

14.

Parallel Mate: Select both bottom faces of the yoke_female and the angled
flange of the bracket. Then select the Orient to assembly reference option
to align parallel. (Parallel is needed here because there is a small gap between the
parts.)

58

15.

Insert the u-joint pin_2.prt, and select the cylindrical faces to mate.

16.

Distance Mate: Select the end face of the pin and then select a parallel flat
face the spider. Add a distance of .35

FINISH

59

17.

Attach the remainder of the components.

18.

After completion you should be able to use the Drag Component icon to
dynamically rotate the assembly.

60

61

EXERCISE 6
Fundamental 2D Drawing Creation
1.

Open the Exercise 6 part file.

2.

View Layout/Drawing Toolbar. Make sure Exercise 6 is shown in the

Default model box, and select Empty with format, then select
a_format. You may need to browse to find the part if it does not show
automatically.

62

3.

The standard a sheet should automatically show up.

4.

To insert views RMB (right mouse button) click/hold in the center of the
drawing. Or select the General icon in the Layout tab tools ribbon.
Select insert general view from the list, and then left click to drop the
new view in.
Select the FRONT option from the Drawing View dialog box and hit
OK. NOTE: If you lose the Drawing View dialog box simply double click
on the drawing view itself to return it.

5.
6.

63

7.
8.

9.

10.

To move the views select the view then RMB click the unlock view
option.
Projection view: Select the front view of the part then select the
Projection option in the Layout tab ribbon.

Section Views: Select the top view and repeat the projection view
steps, and then move the pointer up, LMB click to drop the new view.
Then double LMB click on the view to activate the options of that view.
Turn on/show the Datum Planes

64

11.

Section Views: Select the section option, in the menu manager select
Done, and then create new, then type A in the text box and hit the
green check mark at the right of the screen. Then select the Plane option
to the right, finally you can select the actual plane (horizontal) on the
top view.

FINISH

65

12.

Section view arrows: You select and RMB click on the section view, then
find Add Arrows, click on the Top view and they should appear.

13.

Detail View: Is added by selecting the Detailed tool in the Layout

ribbon. (NOTE: Do not pre-select the view.)

14.

Select a center point for the view, and then sketch a spline around the
area, and center mouse button click to close it. Then click to the right of
the screen to locate and drop the new detail view.

66

15.

Auxiliary views: Are created by selecting the option then selecting the
edge of the flange on the front view. Then select the drop point. Double
click on the view to change its appearance.

16.

Isometric General Views: Are created when you select the general view
icon. Then select the location to drop the view. Double click on the view
to change the appearance.

4
17.

View Display: Can be used to change the views from solid to wireframe
or hidden lines/HLR.

67

18.
Dimensions and Annotations (2 Methods): Select the .
a. Import (Show Model Annotations) dimensions used to create the model
b. Create (New References) dimensions (Note: reference dimensions
cannot be changed)

19.

When importing dimensions try using the feature/view option versus

inserting all the dimensions for the mode as it will cluster all them
together. Feature helps reduce the cluster and yet the dimensions are
editable, providing the benefit to edit the actual parts and assemblies in
a bi-directional fashion from the drawing.

20.

Editing the Sheet: use the Note tool to enter your name and part
number.

68

21.

Printing: Select the Publish tab for print and print preview options.
Note if you find it difficult to print using the Pro Engineer printer tools
select the PDF option and print from Adobe instead.

22.

Transitioning from Radius to Diameter when dimensioning, is simply

done by double clicking on the desired edge then middle click to drop a
Diameter dimension. Versus a single click on an edge will result in a
radius.

69

70

71

EXERCISE 7
Projected Curves and
Sweeping
1.

Sketch this on the Front plane.

2.
3.
4.

Hit Done to exit the sketch.

Select the Right plane and start a sketch on it.
Draw the following.

5.

Hit Done to exit the sketch.

72

6.

Extrude the curve Mid-Plane 4. It should extrude as a surface. Hit the green
check to apply.
FINISH

7.

Go to. Then go to Edit/ Project.

73

8.

Select References/Project a sketch/Sketch1-Curve that you drew/CTRL

select all surfaces/Select the Front Datum/ Flip the arrow

FINISH

74

9.

Select the surface and RMB click to find the Hide option.

10.

You should now have a single 3 Dimensional curve.

75

11.
12.

13.

Hit the Done icon and Sweep/Protrusion using the curve as the Path and
the circle as the Profile.
Also select: SelectTraj/Curve Chain/Select All/Done/Done

Draw a .500 circle at the intersection/end of the curve. Select Done and
OK

76

17.

Start a sketch on the Front plane. Draw the following.

18.

Select Done to exit the sketch.

77

19.
20.

21.

Select Sweep/Protrusion using the curve as the Path and the circle as the
Profile.
Also select: SelectTraj/Curve Chain/Select All/Done/Done

Select the concentric circle icon (buried under the circle tool). Select the
edge of the face and click over the edge to assume an Equal diameter
(R1/R1)

78

22.

22.

Sweep using the new path and converted entity as the profile.

CTRL Select both Protrusions from the Feature Tree, and then select the
Mirror icon. Then select the end face of the body.

79

23.

Now using the tools you have learned over the past 5 weeks finish the
remainder of the model.

Hints to complete the model

24.

Revolve Two Directions

80

The completed part; check to see if your feature tree looks the same as this one.

81

82

EXERCISE 8
Swept Blend/Lofting
Swept Blends create a feature by making transitions between profiles. A Swept blend
can be a base, boss, cut, or surface.
Objective: Create
a boat hull by
lofting multiple
section profiles.

1.

Create 4 datum planes beginning from the Front plane and offset from
each other as shown.
DTM Plane 1 6.00
DTM Plane 2 8.00
DTM Plane 3 1.00

2.

Sketch 1 on the Front plane should look like this use the Spline tool.

83

3.

Sketch 2 on DTM 1 should look like this

4.

Sketch 3 on DTM 2 should look like this

5.

Sketch 4 on DTM 3 should look like this A (.010) profile at the origin.

84

6.

Select the Right datum plane ad draw a horizontal line at the origin and
dimension it 15 long.

7.

Swept Blend: Exit any sketches and select Insert/Swept Blend.

85

8.

References Trajectories: Select the 15 line. Select the Solid option.

9.

Sections/Selected Sections: Select the 4 sketches in order from back to front.

Be sure to select the Insert button for every sketch to be entered.

86

10.

You should have a boat hull now

11.

Use the Mirror feature and select the flat side face as the plane to mirror
from.

12.

Select the hull one more time and hit the green check mark to apply.

87

13.

You are finished with the boat Hull.

14.

(Optional) Now dress it up for the contest

88

EXERCISE 9
Top-Down Assembly Modeling
Top-Down Assembly Modeling is creating parts inside an assembly.

Objective: Create
an assembly of a
pencil sharpener.
If the width is
changed all parts
must update.

1.

Create a new assembly file.

2.

Go to the Create icon.

3.

Save it as E9_Front and drop it on the Front plane. Create the following
part from the drawing.

89

4.

When finished select the Activate option to exit part editing mode.

5.

Insert another new component and save it as E9_Reservoir.

90

6.

Create the following model in the context of the assembly-using offset or

convert entities from the E9_Front model.

91

92

EXERCISE 10
Assembly Editing
This exercise will include both Bottom-Up and Top-Down Assembly Modeling.
Objective: To
update the MP3
Assembly with the
changes requested
by the boss as noted
on the drawing.

7.

Open the file called E10_asm assembly and modify according to the
instructions noted on the drawing provided. You will have to mate the
Battery part file.

93

94

95

EXERCISE 11
Sheet Metal Design
Sheet Metal part files can be very useful for extracting a flat pattern.
Objective: Model a
sheet metal
enclosure using
Top-Down
Assembly methods,
and flatten it.

1.

Go to file/open and select E11 for file type and locate Gear Enclosure.
Extrude

Flatten
Unfold

Trim

Fold

Edge Flange

96

2.

Insert a new part into the assembly; drop it on the end face of a gear shaft
of the assembly. Name it Cover 2 (This will be the enclosure) then select
the front outside face. Convert Entities. Offset

3.

Extrude up to vertex.

97

4.

Once completed the assembly should look like this. Right Mouse click on the
surface of the enclosure and select open.

5.

Convert to sheetmetal Go to an isometric view and ctrl select the four

faces as shown.

98

99

Rotate the view to select the fourth face.

100

6. To convert to a sheet metal part, select the pull down menu Application/Sheet
metal select the shell option.

6.

Select the bottom face and select the Conversion icon.

101

7.

Go to the right view orientation and you should have this section view

8.

Click on the Rip parameters and select the two inside edges. Hit apply.

102

9.

Double click on Bends. Hold the CTRL key while selecting. Hit done and
OK.

10.

Select the flatten icon.

103

12. Return to the assembly.

13. Add holes and additional features.

14. The enclosure is now completed.

104

105

BONUS INFORMATION
ProE Creo Administration
Finding adequate computer hardware to run Inventor can be challenging, this lesson
looks at the multiple aspects of selecting hardware as well as modifying settings inside
Creo to allow it to run efficiently and trouble free.
Selecting an Operating System (OS).
Windows 7
Windows 8
Windows 10
Virtual Memory Settings inside the OS. It may be a good idea to increase or adjust your
virtual memory setting. The norm would be x2 x3 your current amount of ram.
Example 512MB of Ram 1000 1500 MB Virtual Ram. And keep the initial size the same
as the maximum size. It is said that this prevents write errors.

106

Processors (CPU)

BUDGET

Intel
Atom
Celeron
Pentium
Core i3
Core i5
Core i7
Xeon

MID-RANGE
HIGH END
PROFESSIONAL

AMD
Sempron
Athlon II
Phenom X2,3,4,6
VISION A4,6,8,10
FX Series
Opteron

107

Multiprocessing
Most CPU manufacturers are beginning to deliver multiple core processors. This can be
seen with the AMD FX which has up to eight processing cores.

Which one will run Creo fastest? You can find benchmarks at www.spec.org specifically
for Creo or you can look for the generic OpenGL benchmark results that usually use an
OpenGL video game.

The question is: Can Creo benefit from multiple cores? Currently one might find an
average of 10 15% performance increase with general modeling. This is because Creo
is not fully written to take advantage of multithreaded processes. However, using the
Creo Simulation, CFD, or Photolux rendering solutions one may discover 2x 12x faster
performance versus a single core processor. This is because these Creo applications do
take full advantage of multithreaded processing.
The biggest benefit one might find is the ability to multitask while working with an FEA
analysis. This is a long process and you could actually open up another window of Creo
or Outlook and continue working while the analysis is running with little slow down in
performance.
To check out what your computer has inside without opening the case download the
free version of CPUID CUP-Z http://www.cpuid.com/softwares/cpu-z.html
Or ctrl-alt-del and start task manager to see how many threads your CPU has, as well as
how much RAM.

108

Graphics Cards
Here are a few brands that are in the Professional Category and actually have specific
drivers that are written to run Inventor at its best.

NVIDIA Quadro series (not NVS series)

Quadro FX K600 erp.$159 (erp- estimated retail price)

Quadro FX K2000 erp.$499

Quadro FX K4000 erp.$799

ATI FirePro series (not FireMV series)

FirePro 3900 erp.$159

FirePro 5900 erp. $499

FirePro 7900

Intel Xeon
P4000 HD integrated graphics (must be P = Professional rated)

These cards are considerably more expensive that mainstream cards but the benefits of
experiencing less crashes or visual problems with Pro/E outweigh the cost.
If you are using Inventor at work, DONT SKIMP! Buy a professional grade video card. For
home use the nVidia Geforce or AMD Radeon series are fair, but you will still experience
some graphical glitches.
GRAPHICS CARD Creo BENCHMARK (source: www.tomshardware.com)
MEMORY (RAM)
4.0 16.0 GB From simple machined parts to complex assemblies. The more RAM the
better.
3.0 GB+ Requires Windows XP/Vista/7 64 Bit Editions

109

Bonus EXERCISE 3B
Family Tables
Family Tables enable you to create multiple part configurations derived from a single
part file.
GOAL: Learn how to make
multiple part configurations
within a single part file.
In this exercise we make a
cast and machined version
of the ratchet.

1. Open the Exercise_4_FAMILY part file.

110

2. Go to the pull down menu- Tools/Family Tables

3. Select the Insert new insatnce two times. Then hit the Add icon.

111

4. Select the Feature option, then select the Extrude 4, 5, and 6

5. Select OK.
6. Select Verify
7. In the columns type N for no- to supress the feature, or Y for yes for the
feature to be unsupressed. Hit OK.

112

8. Hit Verify once again on the smaller Family Tree box.

9. To view suppressed features on the tree select settings then Model Tree items.

10. To open the additional instances go to File/Open, and select the original file,
when it opens it will prompt you with a list of Family Parts available. FIN

113