5.1 Display OSPF Feature and Characteristics.

5.
0 Open Shortest Path First

(OSPF)
Enterprise Networking, Security, and Automation v7.0

(ENSA)
Module Objectives
Module Title: Single-Area OSPF Concepts
Module Objective: Explain how single-area OSPF operates in both point-to-point and broadcast
multiaccess networks.
Topic Title Topic Objective

OSPF Features and
Describe basic OSPF features and characteristics.
Characteristics
OSPF Packets Describe the OSPF packet types used in single-area OSPF.
OSPF Operation Explain how single-area OSPF operates.
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 2
5.1 Display OSPF feature
and characteristics.
5.1.1 Explain the features and characteristics of the
OSPF routing protocol
OSPF Features and Characteristics
Introduction to OSPF
• OSPF is a link-state routing protocol that was developed as an alternative for the
distance vector Routing Information Protocol (RIP). OSPF has significant advantages
over RIP in that it offers faster convergence and scales to much larger network
implementations.
• OSPF is a link-state routing protocol that uses the concept of areas. A network
administrator can divide the routing domain into distinct areas that help control routing
update traffic.
• A link is an interface on a router, a network segment that connects two routers, or a
stub network such as an Ethernet LAN that is connected to a single router.
• Information about the state of a link is known as a link-state. All link-state information
includes the network prefix, prefix length, and cost.
• This module covers basic, single-area OSPF implementations and configurations.
Components of OSPF
• All routing protocols share similar components. They all use routing protocol messages
to exchange route information. The messages help build data structures, which are
then processed using a routing algorithm.
• Routers running OSPF exchange messages to convey routing information using five
types of packets:
• Hello packet
• Database description packet
• Link-state request packet
• Link-state update packet
• Link-state acknowledgment packet
• These packets are used to discover neighboring routers and also to exchange routing
information to maintain accurate information about the network.
Components of OSPF (Cont.)
OSPF messages are used to create and maintain three OSPF databases, as follows:
Database Table Description
•List of all neighbor routers to which a router has established bi-directional communication.
Adjacency Neighbor
•This table is unique for each router.
Database Table
•Can be viewed using the show ip ospf neighbor command.
•Lists information about all other routers in the network.

Link-state
Topology •The database represents the network LSDB.
Database
Table •All routers within an area have identical LSDB.
(LSDB)
•Can be viewed using the show ip ospf database command.
•List of routes generated when an algorithm is run on the link-state database.

Forwarding Routing •Each router's routing table is unique and contains information on how and where to send
Database Table packets to other routers.
•Can be viewed using the show ip route command.
Components of OSPF (Cont.)
• The router builds the topology table using results of calculations based on the Dijkstra
shortest-path first (SPF) algorithm. The SPF algorithm is based on the cumulative cost
to reach a destination.
• The SPF algorithm creates an SPF tree by placing each router at the root of the tree
and calculating the shortest path to each node. The SPF tree is then used to calculate
the best routes. OSPF places the best routes into the forwarding database, which is
used to make the routing table.
Link-State Operation
To maintain routing information, OSPF routers complete a generic link-state routing
process to reach a state of convergence. The following are the link-state routing steps that
are completed by a router:
1. Establish Neighbor Adjacencies
2. Exchange Link-State Advertisements
3. Build the Link State Database
4. Execute the SPF Algorithm
5. Choose the Best Route
Single-Area and Multiarea OSPF
To make OSPF more efficient and scalable, OSPF supports hierarchical routing using
areas. An OSPF area is a group of routers that share the same link-state information in
their LSDBs. OSPF can be implemented in one of two ways, as follows:
• Single-Area OSPF - All routers are in one area. Best practice is to use area 0.
• Multiarea OSPF - OSPF is implemented using multiple areas, in a hierarchical
fashion. All areas must connect to the backbone area (area 0). Routers
interconnecting the areas are referred to as Area Border Routers (ABRs).
The focus of this module is on single-area OSPFv2.
Multiarea OSPF
• The hierarchical-topology design options with multiarea OSPF can offer the following
advantages.
• Smaller routing tables - Tables are smaller because there are fewer routing table
entries. This is because network addresses can be summarized between areas.
Route summarization is not enabled by default.
• Reduced link-state update overhead - Designing multiarea OSPF with smaller
areas minimizes processing and memory requirements.
• Reduced frequency of SPF calculations -– Multiarea OSPF localize the impact of a
topology change within an area. For instance, it minimizes routing update impact
because LSA flooding stops at the area boundary.
OSPFv3
• OSPFv3 is the OSPFv2 equivalent for exchanging IPv6 prefixes. OSPFv3 exchanges
routing information to populate the IPv6 routing table with remote prefixes.
• Note: With the OSPFv3 Address Families feature, OSPFv3 includes support for both
IPv4 and IPv6. OSPF Address Families is beyond the scope of this curriculum.
• OSPFv3 has the same functionality as OSPFv2, but uses IPv6 as the network layer
transport, communicating with OSPFv3 peers and advertising IPv6 routes. OSPFv3
also uses the SPF algorithm as the computation engine to determine the best paths
throughout the routing domain.
• OSPFv3 has separate processes from its IPv4 counterpart. The processes and
operations are basically the same as in the IPv4 routing protocol, but run
independently.
5.1.2 Describe the types of packets used to establish
and maintain an OSPF neighbor relationship
OSPF Packets
OSPF Packets
OSPF uses the following link-state packets (LSPs) to establish and
maintain neighbor adjacencies and exchange routing updates.
• Type 1: Hello packet Link-State Request (LSR)

• Type 2: Database Description (DBD) packet
• Type 3: Link-State Request (LSR) packet
• Type 4: Link-State Update (LSU) packet
• Type 5: Link-State Acknowledgment (LSAck) packet
OSPF Packets
Video – OSPF Packets
OSPF Packets
OSPF Packets (cont..)
• Type 1: Hello packet - This is used to establish and maintain adjacency with
other OSPF routers.
• Type 2: Database Description (DBD) packet - This contains an abbreviated
list of the LSDB of the sending router and is used by receiving routers to
check against the local LSDB. The LSDB must be identical on all link-state
routers within an area to construct an accurate SPF tree.
• Type 3: Link-State Request (LSR) packet - Receiving routers can then
request more information about any entry in the DBD by sending an LSR.
• Type 4: Link-State Update (LSU) packet - This is used to reply to LSRs and
to announce new information. LSUs contain several different types of LSAs.
• Type 5: Link-State Acknowledgment (LSAck) packet - When an LSU is
received, the router sends an LSAck to confirm receipt of the LSU. The
LSAck data field is empty.
OSPF Packets
Types of OSPF Packets
The table summarizes the five different types of Link State Packets (LSPs) used by
OSPFv2. OSPFv3 has similar packet types.
Type Packet Name Description
1 Hello Discovers neighbors and builds adjacencies between them
2 Database Description (DBD) Checks for database synchronization between routers
3 Link-State Request (LSR) Requests specific link-state records from router to router
4 Link-State Update (LSU) Sends specifically requested link-state records
5 Link-State Acknowledgment (LSAck) Acknowledges the other packet types
OSPF Packets
Link-State Updates
• Routers initially exchange Type 2 DBD packets, which is an abbreviated list
of the LSDB of the sending router. It is used by receiving routers to check
against the local LSDB.
• A Type 3 LSR packet is used by the receiving routers to request more
information about an entry in the DBD.
• The Type 4 LSU packet is used to reply to an LSR packet.
• A Type 5 packet is used to acknowledge the receipt of a Type 4 LSU.
• LSUs are also used to forward OSPF routing updates, such as link changes.
Specifically, an LSU packet can contain 11 different types of OSPFv2 LSAs,
with some of the more common ones shown in the figure. OSPFv3 renamed
several of these LSAs and also contains two additional LSAs.
OSPF Packets
Link-State Updates cont..
• An LSU contains one or more LSAs.

• LSAs contain route information for destination networks.
OSPF Packets
Hello Packet
The OSPF Type 1 packet is the
Hello packet. Hello packets are
used to do the following:
• Discover OSPF neighbors and
establish neighbor adjacencies.
• Advertise parameters on which
two routers must agree to
become neighbors.
• Elect the Designated Router
(DR) and Backup Designated
Router (BDR) on multiaccess
networks like Ethernet. Point-to-
point links do not require DR or
BDR.
5.1.3 Follow OSPF operation
OSPF Operation
Video - OSPF Operation
• This video will cover the 7 states of OSPF operation:
• Down state
• Init state
• Two-way state
• ExStart state
• Exchange state
• Loading state
• Full state
OSPF Operation
Video - OSPF Operation
OSPF Operation
OSPF Operational States
State Description
•No Hello packets received = Down.

Down State •Router sends Hello packets.
•Transition to Init state.
•Hello packets are received from the neighbor.
Init State •They contain the Router ID of the sending router.
•Transition to Two-Way state.
•In this state, communication between the two routers is bidirectional.
Two-Way State •On multiaccess links, the routers elect a DR and a BDR.
•Transition to ExStart state.
OSPF Operation
OSPF Operational States (Cont.)
State Description
On point-to-point networks, the two routers decide which router will initiate
ExStart State the DBD packet exchange and decide upon the initial DBD packet
sequence number.
•Routers exchange DBD packets.
Exchange
•If additional router information is required then transition to Loading;
State
otherwise, transition to the Full state.
•LSRs and LSUs are used to gain additional route information.
Loading State •Routes are processed using the SPF algorithm.
•Transition to the Full state.
Full State The link-state database of the router is fully synchronized.
OSPF Operation
Establish Neighbor Adjacencies
• To determine if there is an OSPF neighbor on the link, the router sends a Hello packet
that contains its router ID out all OSPF-enabled interfaces. The Hello packet is sent to
the reserved All OSPF Routers IPv4 multicast address 224.0.0.5. Only OSPFv2
routers will process these packets.
• The OSPF router ID is used by the OSPF process to uniquely identify each router in
the OSPF area. A router ID is a 32-bit number formatted like an IPv4 address and
assigned to uniquely identify a router among OSPF peers.
• When a neighboring OSPF-enabled router receives a Hello packet with a router ID
that is not within its neighbor list, the receiving router attempts to establish an
adjacency with the initiating router.
OSPF Operation
Establish Neighbor Adjacencies (Cont.)
The process routers use to establish adjacency on a multiaccess network:
1 Down to Init State When OSPFv2 is enabled on the interface, R1 transitions from Down to Init and starts
sending OSPFv2 Hellos out of the interface in an attempt to discover neighbors.
2 Init State When a R2 receives a hello from the previously unknown router R1, it adds R1’s router
ID to the neighbor list and responds with a Hello packet containing its own router ID.
3 Two-Way State R1 receives R2’s hello and notices that the message contains the R1 router ID in the list
of R2’s neighbors. R1 adds R2’s router ID to the neighbor list and transitions to the Two-
Way State.
If R1 and R2 are connected with a point-to-point link, they transition to ExStart
If R1 and R2 are connected over a common Ethernet network, the DR/BDR election
occurs.
4 Elect the DR & BDR The DR and BDR election occurs, where the router with the highest router ID or highest
priority is elected as the DR, and second highest is the BDR
OSPF Operation
Synchronizing OSPF Databases
After the Two-Way state, routers transition to database synchronization states. This is a
three step process, as follows:
• Decide first router: The router with the highest router ID sends its DBD first.
• Exchange DBDs: As many as needed to convey the database. The other router must
acknowledge each DBD with an LSAck packet.
• Send an LSR: Each router compares the DBD information with the local LSDB. If the
DBD has more current link information, the router transitions to the loading state.
After all LSRs have been exchanged and satisfied, the routers are considered
synchronized and in a full state. Updates (LSUs) are sent:
• When a change is perceived (incremental updates)
• Every 30 minutes
OSPF Operation
The Need for a DR
Multiaccess networks can create two
challenges for OSPF regarding the flooding of
LSAs, as follows:
• Creation of multiple adjacencies -
Ethernet networks could potentially
interconnect many OSPF routers over a
common link. Creating adjacencies with
every router would lead to an excessive
number of LSAs exchanged between
routers on the same network.
• Extensive flooding of LSAs - Link-state
routers flood their LSAs any time OSPF is
initialized, or when there is a change in the
topology. This flooding can become
excessive.
OSPF Operation
LSA Flooding with a DR
• An increase in the number of routers on a multiaccess network also increases the
number of LSAs exchanged between the routers. This flooding of LSAs significantly
impacts the operation of OSPF.
• If every router in a multiaccess network had to flood and acknowledge all received
LSAs to all other routers on that same multiaccess network, the network traffic would
become quite chaotic.
• On multiaccess networks, OSPF elects a DR to be the collection and distribution point
for LSAs sent and received. A BDR is also elected in case the DR fails. All other
routers become DROTHERs. A DROTHER is a router that is neither the DR nor the
BDR.
• Note: The DR is only used for the dissemination of LSAs. The router will still use the best next-
hop router indicated in the routing table for the forwarding of all other packets.
Module Practice and Quiz
What Did I Learn In This Module?
• Open Shortest Path First (OSPF) is a link-state routing protocol that was developed as an
alternative for the distance vector Routing Information Protocol (RIP).
• OSPF is a link-state routing protocol that uses the concept of areas for scalability.
• A link is an interface on a router. A link is also a network segment that connects two routers, or a
stub network such as an Ethernet LAN that is connected to a single router.
• All link-state information includes the network prefix, prefix length, and cost.
• All routing protocols use routing protocol messages to exchange route information. The messages
help build data structures, which are then processed using a routing algorithm.
• Routers running OSPF exchange messages to convey routing information using five types of
packets: the Hello packet, the database description packet, the link-state request packet, the link-
state update packet, and the link-state acknowledgment packet.
• OSPF messages are used to create and maintain three OSPF databases: the adjacency database
creates the neighbor table, the link-state database (LSDB) creates the topology table, and the
forwarding database creates the routing table.
• The router builds the topology table using results of calculations based on the Dijkstra SPF
(shortest-path first) algorithm. The SPF algorithm is based on the cumulative cost to reach a
destination. In OSPF, cost is used to determine the best path to the destination.
• To maintain routing information, OSPF routers complete a generic link-state routing process to
reach a state of convergence: Establish Neighbor Adjacencies, Exchange Link-State
Advertisements, Build the Link State Database, Execute the SPF Algorithm, Choose the Best
Route
• With single-area OSPF any number can be used for the area, best practice is to use area 0.
• Single-area OSPF is useful in smaller networks with few routers.
• With multiarea OSPF, one large routing domain can be divided into smaller areas, to support
hierarchical routing. Routing still occurs between the areas (interarea routing), while many of the
processor intensive routing operations, such as recalculating the database, are kept within an area.
• OSPFv3 is the OSPFv2 equivalent for exchanging IPv6 prefixes. Recall that in IPv6, the network
address is referred to as the prefix and the subnet mask is called the prefix-length.
• OSPF uses the following link-state packets (LSPs) to establish and maintain neighbor adjacencies
and exchange routing updates: 1 Hello, 2 DBD, 3 LSR, 4 LSU, and 5 LSAck.
• LSUs are also used to forward OSPF routing updates, such as link changes.
• Hello packets are used to: Discover OSPF neighbors and establish neighbor adjacencies,
Advertise parameters on which two routers must agree to become neighbors, and Elect the
Designated Router (DR) and Backup Designated Router (BDR) on multiaccess networks like
Ethernet. Point-to-point links do not require DR or BDR. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 32
• Some important fields in the Hello packet are type, router ID, area ID, network mask, hello interval,
router priority, dead interval, DR, BDR and list of neighbors.
• The states that OSPF progresses through to do reach convergence are down state, init state, two-
way state, ExStart state, Exchange state, loading state, and full state.
• When OSPF is enabled on an interface, the router must determine if there is another OSPF
neighbor on the link by sending a Hello packet that contains its router ID out all OSPF-enabled
interfaces.
• The Hello packet is sent to the reserved All OSPF Routers IPv4 multicast address 224.0.0.5. Only
OSPFv2 routers will process these packets.
• When a neighboring OSPF-enabled router receives a Hello packet with a router ID that is not within
its neighbor list, the receiving router attempts to establish an adjacency with the initiating router.
• After the Two-Way state, routers transition to database synchronization states, which is a three
step process:
• Multiaccess networks can create two challenges for OSPF regarding the flooding of LSAs: the
creation of multiple adjacencies and extensive flooding of LSAs.
• A dramatic increase in the number of routers also dramatically increases the number of LSAs
exchanged between the routers.
• This flooding of LSAs significantly impact the operation of OSPF. If every router in a multiaccess
network had to flood and acknowledge all received LSAs to all other routers on that same
multiaccess network, the network traffic would become quite chaotic. This is why DR and BDR
election is necessary.
• On multiaccess networks, OSPF elects a DR to be the collection and distribution point for LSAs
sent and received. A BDR is also elected in case the DR fails.

5.1 Display OSPF Feature and Characteristics.

Uploaded by

Copyright:

Available Formats

5.1 Display OSPF Feature and Characteristics.

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

5.1 Display OSPF Feature and Characteristics.

Uploaded by

Copyright:

Available Formats

5.

0 Open Shortest Path First

Enterprise Networking, Security, and Automation v7.0

Topic Title Topic Objective

Database Table Description

•Lists information about all other routers in the network.

•List of routes generated when an algorithm is run on the link-state database.

• Type 1: Hello packet Link-State Request (LSR)

Type Packet Name Description

1 Hello Discovers neighbors and builds adjacencies between them

2 Database Description (DBD) Checks for database synchronization between routers

4 Link-State Update (LSU) Sends specifically requested link-state records

5 Link-State Acknowledgment (LSAck) Acknowledges the other packet types

• An LSU contains one or more LSAs.

•No Hello packets received = Down.

You might also like