DATA NETWORKS, PROTOCOLS & SECURITY (DNPS)

22EC2210R
TOPIC:
NETWORK HARDWARE
NETWORKSOFTWARE

SESSION - 02
 AIM OF THE
SESSION
To familiarize students with the basic concept of computer networks and its necessity

INSTRUCTIONAL
OBJECTIVES

This Session is designed to:

1. Introduction to NETWORK HARDWARE
2. Describe the Features Of Computer network
3. Introduction to NETWORK TOPOLOGIES

LEARNING OUTCOMES

At the end of this session, you should be able to:

1. Describe the Introduction to NETWORK HARDWARE
2. Describe the Introduction to NETWORK TOPOLOGIES
 Syllabus
Introduction to networks: Introduction to Computer networks Use of Computer Networks, Network

Topologies, types of networks, Reference models: OSI and TCP/IP,

 COMPUTER NETWORK HARDWARE

•Network Cables
•Distributors
•Routers
•Socket.
•Port
•Network Card
 Network Cables

Network cables are used to connect computers. RJ-45

Category 5 cable is the most often used cable.
 Distributors

A computer may be connected to another using a serial port; however, if

we need to connect numerous computers to create a network, this serial
connection will fail.
 Router
A router is an equipment that serves as the hub for computers and other network-connected devices. It
has openings called ports in it. Computers and other devices are connected to a router through
network cables. Nowadays, routers are available in wireless modes, allowing computers to be
connected without needing a physical connection.
SOCKET

• A socket is one endpoint of a two way communication link between two programs
running on the network. The socket mechanism provides a means of inter-process
communication (IPC) by establishing named contact points between which the
communication take place.

8
PORT

• In computer networking, a port or port number is a number assigned to uniquely

identify a connection endpoint and to direct data to a specific service. At the software
level, within an operating system, a port is a logical construct that identifies a specific
process or a type of network service. A port at the software level is identified for each
transport protocol and address combination by the port number assigned to it. The most
common transport protocols that use port numbers are the Transmission Control Protocol
(TCP) and the User Datagram Protocol (UDP); those port numbers are 16-bit
unsigned numbers.

9
REPEATERS, HUBS, AND SWITCHES

• Repeaters, hubs and switches connect network devices together so that they can function as
a single segment.
• A repeater receives a signal and regenerates it before re-transmitting so that it can travel
longer distances.
• A hub is a multiport repeater having several input/output ports, so that input at any port is
available at every other port.
• A switch receives data from a port, uses packet switching to resolve the destination device
and then forwards the data to the particular destination, rather than broadcasting it as a hub.

10
 Network Card

A network card is a component of a computer connected to a network

computer. It is sometimes referred to as a network adapter or Network
Interface Card (NIC). Most brand-name computers come with a network
card pre-installed. Internal and external network cards are the two types
of network cards.
PERSONAL AREA NETWORK

Bluetooth PAN configuration

12
TYPES OF NETWORKS

• LAN(Local Area Network)

• PAN(Personal Area Network)
• MAN(Metropolitan Area Network)
• WAN(Wide Area Network)

13
LOCAL AREA NETWORKS

Wireless and wired LANs. (a) 802.11. (b) Switched Ethernet.

14
 LOCAL AREA NETWORKS

 Characteristics
 small size
 transmission technology
• single cable (single channel)
• 10Mbps ~ 10Gb/s
• 10Gb/s : 10,000,000.000 bps

1
5
METROPOLITAN AREA NETWORKS

A metropolitan area network based on cable TV.

24 1
6
 WIDE AREA NETWORKS
(WANS)
·WANs are point-to-point networks
·WANs consist of two distinct components:
transmission lines (copper, fiber, microwave) and switches (electronics, optics)
 Store-and-forward or packet-switched subnet

Relation between hosts on LANs and the subnet.

25 1
7
NETWORK
TOPOLOGY

29 1
8
 BUS TOPOLOGY

A bus topology is multipoint connection, one long cable acts as a backbone to link all the devices in a
network. Here the cable is called the bus.
Bus topology was the one of the first topologies used in the design of early local area networks.
Nodes are connected to the bus cable by drop lines and taps.
A drop line is a connection running between the device and the main cable.
A tap is a connector that splices into (attached to) the main cable.
• Advantages:
1. Installation is easy. Bus Backbone cable can be laid along the most efficient path and then connected to
the nodes by drop lines of various lengths.
2. A bus uses less cabling than mesh or star topologies.

Disadvantages:
1. All the devices are connected to bus backbone cable, so that if the backbone cable fails the entire system
fails.
2. Difficult Reconnection and Fault Isolation. It is difficult to add new devices.
3. There is a limit on the number of taps a bus can support and on the distance between those taps.
4. More heat is generated if the number of taps are more. Heat degrades the quality of signal.

20
RING TOPOLOGY

• In a ring topology, each device has a dedicated point-to-point connection with only the
two devices on either side of it.
A signal is passed along the ring in one direction from device to device, until it reaches its
destination.
Each device in the ring incorporates a repeater. When a device receives a signal intended
for another device, its repeater regenerates the bits and passes them along.

21
CONTD

• Advantages:
1. A ring is relatively easy to install and reconfigure. Each device is linked to only its immediate
neighbors (either physically or logically).
2. To add or delete a device requires changing only two connections.
3. The only constraints are media and traffic considerations (maximum ring length and number of
devices).
Disadvantage:
1. Unidirectional traffic can be a disadvantage.
2. In a simple ring, a break in the ring (such as a disabled station) can disable the entire network.

22
 STAR TOPOLOGY

In a star topology, each device has a dedicated point-to-point link only to a central controller called a Hub or Switch. The
devices are not directly linked to one another.
A star topology does not allow direct traffic between devices. The controller acts as an exchange: If one device wants to
send data to another, it sends the data to the controller, and the controller transfers the data to the other connected device.
• Advantages:
1. A star topology is less expensive than a mesh topology. In a star, each device needs only one link
and one I/O port to connect it to any number of others. This factor also makes it easy to install and
reconfigure
2. Less cabling is required than mesh topology.
3. Star topology is robust, If one link fails, only that link is affected. All other links remain active.

Disadvantages:
1. If hub fails entire processing will be stopped working. Uses:
1. It is used in High-speed LAN’s often use a star topology with a central hub.

24
 MESH TOPOLOGY

In a mesh topology, every device has a Dedicated Point-to-Point link to

every other device. (i.e.) for each node there is a link to all other nodes.
The term Dedicated means that the link carries traffic only between the
two devices it connects.
 HYBRID TOPOLOGY

It is a combination of two or more topologies for

example star topology with each branch connecting
several stations in a bus topology
NETWORK SOFTWARE

• Network software encompasses a broad range of software used for design,

implementation, and operation and monitoring of computer networks. Traditional
networks were hardware based with software embedded. With the advent of Software –
Defined Networking (SDN), software is separated from the hardware thus making it more
adaptable to the ever-changing nature of the computer network.

27
• SDN Framework
• The Software Defined Networking framework has three layers as depicted in the following diagram −
• APPLICATION LAYER − SDN applications reside in the Application Layer. The applications convey their
needs for resources and services to the control layer through APIs.
• CONTROL LAYER − The Network Control Software, bundled into the Network Operating System, lies in
this layer. It provides an abstract view of the underlying network infrastructure. It receives the requirements of
the SDN applications and relays them to the network components.
• INFRASTRUCTURE LAYER − Also called the Data Plane Layer, this layer contains the actual network
components. The network devices reside in this layer that shows their network capabilities through the Control
to data-Plane Interface.

28
 SELF-ASSESSMENT QUESTIONS

COMPUTER TOPOLOGIES ARE ………….. TYEPS

6
7
5
3

Ethernet (IEEE 802.3): ……………………..Mbps (10Gb/s)

 TERMINAL QUESTIONS

1. Describe the NETWORK HARDWARE

2. List out the FEATURES OF COMPUTER NETWORK

3. Describe the Purpose of. the TOPOLOGIES

 REFERENCES FOR FURTHER LEARNING OF THE
SESSION

Reference Books:
1. Simon Haykin and Michael Moher, “An Introduction to Analog and Digital Communications”,
2nd Ed., Wiley, (2007).
2. Wayne Tomasi,”Advanced Electronic Communication Systems”, 6th Ed., Pearson Education.
3. B P Lathi and W.Ding, “Modern Digital and Digital and Analog Communication,” ”, 4 th Ed.,
Wiley, (2007).

Sites and Web links:

1. https://archive.nptel.ac.in/courses/108/106/108106163/
2. https://onlinecourses.nptel.ac.in/noc22_ee32/preview
3. https://onlinecourses.nptel.ac.in/noc23_ee05/preview
 THANK YOU

Team –NETWORK PROTOCOLS & SECURITY (NPS)