SOPORTERIA

Installation Systems
Hilti. Outperform. Outlast.
Installation Systems
Strut . . . . . . . . . 232
B2B Strut and Brackets . . . . . . . . . 233
Fasteners . . . . . . . . . 234
3D System . . . . . . . . . 236
Angles and Connectors . . . . . . . . . 237
Splice Plates, Clamps and Bases . . . . . . . . . 238
Strut Accesories . . . . . . . . . 240
Pipe Hangers . . . . . . . . . 242
Beam Clamps . . . . . . . . . 244
Split Rings . . . . . . . . . 246
Riser Clamps . . . . . . . . . 247
Strut Clamps . . . . . . . . . 248
Threaded Accessories . . . . . . . . . 250
Seismic Hinges, Stiffeners and Cast-In Systems . . . . . . . . . 252
MI Industrial Support System . . . . . . . . . 253

Hilti, Inc. (U.S.) 1-800-879-8000 www.us.hilti.com en espaol 1-800-879-5000 Hilti (Canada) Corp. 1-800-363-4458 www.hilti.ca
231
Strut
Hilti Strut (12 and 14 ga)
Features and Applications

C-profile with serrated edges for greater hold and adjustability with MQN Pushbuttons, strut nuts and saddle nuts Stamped markings every 2" to assist with measurement, cutting, and installation Reduced inventory by replacing spring nuts, washers and bolts with MQN Pushbuttons, strut nuts or saddle nuts Slots for greater flexibility and longitudinal swaging for greater strength Four (4) finishes to meet your job requirements: PG Pre-Galvanized; HDG Hot-Dipped Galvanized; SS 316 Ti Stainless Steel; GR E-coat Electro-Disposition Coating (Green)
Strut 13/16 in-12 gauge

Description Hole Configuration Weight per piece (lb) Qty Item No. Single piece Qty (VIP) Item No. VIP Pack
Strut 13/16 in-12 ga/PG 10 ft Strut 13/16 in-12 ga/PG 20 ft Strut 13/16 in-12 ga/PGS 10 ft Strut 13/16 in-12 ga/PGS 20 ft Strut 13/16 in-12 ga/HDG 10 ft
2-1/2 in x 9/16 in 2-1/2 in x 9/16 in solid solid 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-5/8 in x 11/16 in 2-1/2 in x 9/16 in solid solid 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 11/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in solid 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in 2-1/2 in x 9/16 in solid
12.2 24.3 15.4 30.8 12.8 3.6 7.2 10.8 12.0 18.0 18.0 36.0 18.5 37.0 18.0 36.0 18.8 18.8 24.5 49.0 48.5 8.7 17.4 9.7 8.7 9.9 13.6 27.2 13.9
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
00407543 00407544 00407545 00407546 00407569 00407551 00407552 00407553 00407554 00407555 00407560 00407557 00407561 00407562 00407558 00407559 00407570 03424527 00407566 00407567 00407568 00407547 00407548 00407549 00407550 03445372 00407563 00407564 00407565
50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 12 40 40 50 50 50 50 50 50 50
03453066 03453067 03453064 03453065 03453650 03453075 03453076 03453077 03453078 30453079 03453081 03453080 03453073 03453074 03453083 03453084 03453082 03424528 03453087 03453088 03453070 03453071 03453069 03453072 30453085 03453086 03453089
Strut 1-5/8 in-12 gauge

Strut 1-5/8 in-12 ga/PG 2 ft Kwik Cut Strut 1-5/8 in-12 ga/PG 4 ft Kwik Cut Strut 1-5/8 in-12 ga/PG 6 ft Kwik Cut Strut 1-5/8 in-12 ga/PG 6 ft 8 in Kwik Cut Strut 1-5/8 in-12 ga/PG 10 ft Strut 1-5/8 in-12 ga/PG 10 ft (11/16" slot) Strut 1-5/8 in-12 ga/PG 20 ft Strut 1-5/8 in-12 ga/PGS 10 ft Strut 1-5/8 in-12 ga/PGS 20 ft Strut 1-5/8 in-12 ga/GR E-coat 10 ft Strut 1-5/8 in-12 ga/GR E-coat 20 ft Strut 1-5/8 in-12 ga/HDG 10 ft Strut 1-5/8 in-12 ga/SS316 Ti 10 ft

Strut 2-7/16 in-12 ga/PG 10 ft Strut 2-7/16 in-12 ga/PG 20 ft Strut 2-7/16 in-12 ga/PG 20 ft (11/16" slot)
Strut 13/16 in-14 gauge

Strut 13/16 in-14 ga/PG 10 ft Strut 13/16 in-14 ga/PG 20 ft Strut 13/16 in-14 ga/PGS 10 ft Strut 13/16 in-14 ga/PG E-coat 10 ft Strut 13/16 in-14 ga/SS316 Ti 10 ft

Strut 1-5/8 in-14 ga/PG 10 ft Strut 1-5/8 in-14 ga/PG 20 ft Strut 1-5/8 in-14 ga/PGS 10 ft
Material / Finishes Pre-Galvanized

Pre-galvanized strut is manufactured using material produced by passing carbon steel sheets through a molten zinc bath in a process known as hotdip mill galvanization". The material conforms to ASTM A 653 grade 33 with a zinc thickness of G90 or 0.9 ounces of zinc per square foot. The channel is formed and slots are punched after the hot-dip process hence the name pre-galvanized strut. Surfaces of the punched and cut portions are somewhat protected by the adjacent zinc plating which acts as a sacrificial anode impeding corrosion of the raw edges.
Stainless Steel
SS 316 Ti for strut and MQK brackets. SS 316 for angles, connectors, bases, splices and fasteners
Electro-Deposition Coating
Electro-Galvanized
Carbon steel angles, connectors, bases, splices and fasteners are dipped in a molten zinc bath.
Electro-Deposition Coating or E-Coating uses electricity to deposit a smooth, thin, uniform layer of plastic coating on the surface of the steel channel. The epoxy-coated strut is then cured in an oven at 400 C for 20 minutes. Salt spray (fog) testing has been conducted to verify the performance of the finish the plastic coating was tested 600 hours in a salt spray chamber, in accordance with ASTM B 117-03.
Hot Dipped Galvanized
Strut
Manufactured to MFMA-4
According to ASTM A 123 for strut and ASTM A 153 for angles, connectors, bases, splices and fasteners.
232

Strut and Brackets
Back-to-Back Strut (12 ga)

Self-riveting process provides consistently superior channel-to-channel fastening over spot welding Integrity of galvanized coating is maintained in self-riveting process 1-9/16" x 9/16" slots, allow up to 1/2" threaded rod to pass through back-to-back strut without drilling C-profile with serrated edges for greater hold and adjustability with MQN Pushbuttons, strut nuts and saddle nuts Stamped markings every 2" to assist with measurement, cutting, and installation
Strut 13/16 in-12 gauge back-to-back

Strut 13/16 in-12 ga/PG (10 ft 1 in) B2B
1-9/16 in x 9/16 in
23.0
03424489
25
03424490
Strut 1-5/8 in-12 gauge back-to-back

Strut 1-5/8 in-12 ga/PG (10 ft 1 in) B2B Strut 1-5/8 in-12 ga/PG (19 ft 11-1/4 in) B2B Strut 1-5/8 in-12 ga/SS316 Ti (10 ft 1 in) B2B
1-9/16 in x 9/16 in 1-9/16 in x 9/16 in 1-9/16 in x 9/16 in
35.9 80.8 35.9
1 1 1
03424515 03424517 03424529
25 25 -
03424516 03424518 -
MQK Bracket

C-profile with serrated edges for increased hold Installation assisted by dimension marking Slotted for greater flexibility Back-to-back brackets welded all around
Technical Data
Materials Finishes
MQK
Carbon steel Stainless steel 316 Ti Electro-galvanized Hot-dipped galvanized
MQK-21
Description Strut Length (in) Strut Length (mm) Strut Section (ga/mm) Weight per piece (lb) Qty Item No. Single piece
MQK-21/300 MQK-21/450 MQK-21/450-F HDG
11-13/16 in 17-11/16 in 17-11/16 in
300 450 450
14/2 14/2 14/2
1.48 1.96 1.96
1 1 10
00369607 00369608 00304114
MQK-41/3
MQK-41/3/300 MQK-41/3/600 MQK-41/600-F HDG MQK-41/600-R SS316 Ti
11-13/16 in 23-5/8 in 23-5/8 in 23-5/8 in
300 600 600 600
12/3 12/3 14/2 14/2
2.62 4.54 3.46 3.46
1 1 10 1
00370595 00370597 00304117 00304007

17-11/16" , 23-5/8" 13/16" x 9/16" 3/8"
4-3/4" 6-1/2"
MQK-72
MQK-72/600
23-5/8 in
600
12/2.75
6.90
00369616
2-3/8"
MQK-21D
MQK-21D/300 MQK-21D/600
11-13/16 in 23-5/8 in
300 600
14/2 14/2
2.76 4.83
1 1
00369617 00369619
MQK-41D
MQK-41D/1000-F HDG
39-3/8 in 29-1/2 in
1000 750
14/2 14/2
11.20 6.02
6 1
00304127 00304009
MQK-41D/750-R SS316 Ti

233
Fasteners
MQN Pushbutton

Fast: one-part fastener replaces a spring nut, bolt and washer Removable and reusable Universal one MQN Pushbutton fits all Hilti strut profiles
Technical Data
Materials Finishes
MQN
Carbon steel Stainless steel 316 Electro-galvanized Hot-dipped galvanized
Allowable Loads2, 3 Tension (lb) Zrec MQN MQN-F MQN-R 1800 1800 1800 Shear (lb)1 Qrec 1100 400 1100
Tightening Torque MD (ft-lb) 30 30 30
1 Shear loading applies to a single fastening using Hilti serrated strut. The value for MQN double fastening is 1.8 x single button. Contact Hilti for loading information when using Hilti Pushbuttons in non-serrated 2 Based on a safety factor of 2.2. 3 Based on use in 12 gauge strut
Description
Weight/Piece (lb)
Qty
Item No.
MQN MQN-F (HDG) MQN-R (SS316)
0.145 0.185 0.170
50 50 25
00369623 00387779 00304012
Use the Hilti Pushbutton System of fasteners & connectors to replace spring nuts, bolts & washers for time & labor savings Installed Costs Savings Case Study #2438* Project Manager
$6000 project labor savings using the onepiece Hiliti Pushbutton Fastening System over the traditional method using spring nuts, bolts and washers.
*For complete details, contact Hilti. Actual results may vary.
Put in position.
Press and turn.
Tighten using 11/16" socket.
Total Installed Cost Savings Total Installation Cost Using Hilti Innovation
Hilti Innovation
Cost Savings
Your total installed cost savings are maximized by reducing labor time using Hiltis innovative products and solutions.
Material
Labor
Total Installation Cost Using Current Practices Current Practices

While material purchased in bulk may save on up front costs, labor intensive fabrication, welding, grinding, and painting greatly increases total installed cost.
Material
Labor
234

Fasteners
MQM Wing Nut

Alternative to spring nut Fast, easy installation in all strut profiles Eliminates stocking of spring nuts for each depth of strut
Technical Data
Materials Finishes
MQM
Allowable Loads2, 3 Tension (lb) Zrec MQM-F 1/4" MQM-F 3/8" MQM-F 1/2" MQM-F 3/8"-F MQM-F 1/2"-F MQM-F 1/4"-R MQM-F 3/8"-R
Description Connection Thread Weight/Piece (lb) Qty Item No.
Shear (lb) 1 Qrec 415 1125 1125 400 400 415 1125 1125
Tightening Torque MD (ft-lb) 7 15 30 15 30 7 15 30
755 1800 1800 1800 1800 755 1800 1800
MQM-F 1/2"-R
MQM-F 1/4" MQM-F 1/4"-R (SS316) MQM-F 3/8" MQM-F 3/8"-F (HDG) MQM-F 3/8"-R (SS316) MQM-F 1/2" MQM-F 1/2"-F (HDG) MQM-F 1/2"-R (SS316)
1/4" 1/4" 3/8" 3/8" 3/8" 1/2" 1/2" 1/2"
0.077 0.060 0.075 0.080 0.050 0.073 0.080 0.050
50 25 50 25 25 50 25 25
00377881 00304018 00377882 00304136 00304019 00377883 00304137 00304020
1 Shear loading applies to a single fastening using Hilti serrated strut. Contact Hilti for loading data when using Hilti MQM-F fasteners in non-serated strut profiles. 2 Based on a safety factor of 2.2. 3 Based on use in 12 gauge strut
1/4" 3/8" 1/2"
MQA Saddle Nut

A single part replacing spring nuts and base plates For all strut profiles
Technical Data
Materials Finishes
MQA
Carbon steel Stainless steel 316 Electro-galvanized Hot-dipped galvanized Allowable Loads Tension (lb) 1 Zrec Tightening Torque MD (ft-lb) 7 15 30 30 15 30 30 7 15 30 30
MQA-F 1/4" MQA-F 3/8" MQA-F 1/2" MQA-F 5/8" MQA-F 3/8"-F MQA-F 1/2"-F MQA-F 5/8"-F
Description Connection Thread Weight/Piece (lb) Qty Item No.
490 1800 1800 2100 1800 1800 2100 490 1800 1800 2100
MQA-F 1/4"-R MQA-F 3/8"-R MQA-F 1/2"-R MQA-F 5/8"-R
MQA-F 1/4" MQA-F 1/4"-R (SS316) MQA-F 3/8" MQA-F 3/8"-F (HDG) MQA-F 3/8"-R (SS316) MQA-F 1/2" MQA-F 1/2"-F (HDG) MQA-F 1/2"-R (SS316) MQA-F 5/8" MQA-F 5/8"-F (HDG) MQA-F 5/8"-R (SS316)
1/4" 1/4" 3/8" 3/8" 3/8" 1/2" 1/2" 1/2" 5/8" 5/8" 5/8"
0.194 0.190 0.192 0.192 0.180 0.183 0.183 0.160 0.185 0.185 0.170
50 25 50 25 25 50 25 25 50 25 25
00377884 00401397 00377885 00304143 00401398 00377886 00304144 00401399 00377887 00304145 00401400
1 Based on a safety factor or 2.2 when used with Hilti 12 gauge serrated strut profile
1/4" 3/8" 1/2" 5/8"

235
3D System
MQ3D 3D System

Universal, few parts for all applications Quick and easy to use 45 angle and bracing with predetermined bending point For installation of angles or connectors on-site
Technical Data
Material Material thickness Finish Tightening torque
MQ3D
Carbon steel 1/8" (3 mm) Electro-galvanized 30 ft-lb (40 Nm)
3/ " 4
3/ " 4
1-3/8"
3/ " 8
3-9/16"
2-3/8"
Description
Weight/Piece (lb)
Qty
Item No.
1"
MQ3D-B 3D Base Connector MQ3D-W90 3D 90 Connector MQ3D-W45 3D 45 Connector MQ3D-A 3D Threaded Rod Brace
0.454 0.467 0.337 0.209
20 20 16 20
00369694 00369695 00369696 00369697

1-15/16"
7/ " 8
1-15/16" 45 45
1-3/16"
1"
Example of Application
&
Frec Qrec MQN with MQ3D-B
Supported at both ends
Frec = 560 Ib (2.5 kN)
&
Tension/compression bracing
Frec = 560 Ib (2.5 kN)
bo ds
Variable angle
pp
Frec Qrec MQN with MQ3D-B
Directly to strut
Frec Qrec MQM-F3/8" fastened to strut with MQZ-L3/8" base plate 3/8"-1" (min.) hex. bolt MQM-F3/8" strut nut
Frec = 560 Ib (2.5 kN) Variable angle
&
See Note See Note
Tension bracing
Frec = 560 Ib (2.5 kN) Frec Qrec MQN with MQ3D-B Variable angle

Directly to strut
Frec Qrec MQM-F3/8" fastened to strut with MQZ-L3/8" base plate 3/8"-1" (min.) hex. bolt MQM-F3/8" strut nut
3/8"diameter rod
Frec = 560 Ib (2.5 kN) Variable angle
See Note
Note: Pre-assembled bolts may be removed and replaced with an anchor or longer 3/8 bolt when mounting to surface other than the 3D Base Connector. All recommended loads are based on a safety factor of 2.2.
236
Su
or
te
at
th
en
Angles and Connectors
MQW-Q2 Pre-Assembled 90 Angle

Helps reduce inventory costs Fast and easy installation helps complete jobs more quickly and reduce labor costs Single item 90 connection no lost parts Fits all Hilti Strut Utilizes Hilti Pushbutton technology
Technical Data
Material Finish Tightening torque Material thickness Width across flats
MQW-Q2
Carbon steel Electro-galvanized 30 ft-lb 1/8" 11/16"
Description
Weight/Piece (lb)
Qty
Item No.
MQW-Q2 90 Angle
0.441
20
00369655
2-3/16"
2-3/16"
Press and turn.
Tighten using 11/16" socket.
MQK Angle brace

Construction of wall brackets Easy customized stand-alone construction 2-hole angle base for MQN pushbutton Channel assembly in two positions possible Self construction of brackets
Technical Data
Materials Finish Material width Material thickness
MQK
Carbon steel Stainless Steel 316 Electro-galvanized Hot-dipped galvanized 1-9/16" (40 mm) 5/32" or 1/8" (4 or 3 mm)
MQK-Angle Brace
Description A (in/mm) H (in/mm) L (in/mm)
45 45 45 45
Qty
Item No.
MQK-SK (short brace) MQK-SL (long brace) MQK-SK-F (HDG - short brace) MQK-SL-R (SS316 - long brace)
14/355 25/635 14/355 25/635
13/328 20-7/8/528 13/328 20-7/8/528
12-13/16/324 20-1/2/524 12-13/16/324 20-1/2/524
10 10 10 10
00369622 00369621 00304129 00304010

H
2-15/16"
7/16"
1-5/16" 9/16"

237
Angles and Connectors
MQW Angle

Helps reduce inventory costs Fast and easy installation helps complete jobs more quickly and reduce labor costs Single item 90 connection no lost parts Fits all Hilti Strut Utilizes Hilti Pushbutton technology
Technical Data
Materials Material thickness Finish
MQW
Carbon steel Stainless Steel 316 5/32" (4 mm) Electro-galvanized Hot-dipped galvanized
Description
Weight/Piece (lb)
Qty
Item No.
MQW-2-R Two Hole 90 (SS316) MQW-3 Three Hole 90 MQW-3-F Three Hole 90 (HDG) MQW-3-R Three Hole 90 (SS316) MQW-4 Four Hole 90 MQW-8/90 Eight Hole 90 MQW-8/90-F Eight Hole 90 (HDG) MQW-8/90-R Eight Hole 90 (SS316) MQW-3/45 Three Hole 45 MQW-3/45-R Three Hole 45(SS316) MQW-8/45 Eight Hole 45 MQW-S/1 Single Brace Angle Bracket MQW-S/2 Double Brace Angle Bracket
0.243 0.353 0.353 0.353 0.485 0.926 0.926 0.926 0.342 0.342 0.904 1.014 2.602
10 20 20 10 10 10 10 10 20 10 10 10 10
00304051 00369656 00304172 00304052 00369658 00369659 00304175 00304055 00369657 00304053 00369660 00369664 00369665
7-7/8"
2-3/8" 4-3/8"
2-3/16"
4-1/8"
2-3/16" 45 4-3/16"
7-7/8"
3-15/16"
9/ " 16
MQV In-Line Channel Connector
Technical Data
Materials Material thickness Finishes
MQV
Description
Weight/Piece (lb)
Qty
Item No.
MQV-2/2D MQV-2/2D-R (SS316) MQV-3/2D MQV-3/2D-F (HDG) MQV-3/2D X MQV-3/3D MQV-4/3D MQV-12 MQV-12-F (HDG) MQV-12-R (SS316)
0.966 0.970 1.356 1.327 3.245 0.994 1.698 1.224 1.285 1.224
10 10 10 10 10 10 10 10 10 10
00369638 00304032 00369640 00304152 00339590 00369641 00369642 00369643 00304155 00304037
6-1/2"
6-1/2"
6-11/16"
10-1/4"
4-7/16"
4-7/16"
2"
2-3/16"
2-3/16"
8-1/16" 1-3/4"
4-7/16"
4-7/16"
238

Splice Plates, Clamps & Bases
MQV Flat Connector

Channel to strut connection on the same level
Technical Data
MQV
Carbon steel 5/32" (4 mm) Electro-galvanized Hot-dipped galvanized
Description
Weight/Piece (lb)
Qty
Item No.
8-1/16"
1-7/8" 3-3/4"
MQV-P4 Four Hole MQV-P4-F Four Hole (HDG) MQV-P2 Two Hole Tee MQV-T Four Hole Tee MQV-P3 Three Hole Cross MQV-P5 Five Hole Cross
0.415 0.415 0.220 0.432 0.309 0.309
10 10 10 10 10 10
00369644 00304156 00370630 00369645 00370629 00370631
1-5/8"
MQB Clamp

Various clamp sizes Suitable for all the different strut profiles
Technical Data
6-5/16" 4-3/16"
MQB
Carbon steel Stainless Steel 316 5/32" (4 mm) Electro-galvanized
Description
Weight/Piece (lb)
Strut Profile
Qty
Item No.
6-5/16" 4-3/16"
MQB-21 MQB-41 MQB-41-R (SS316) MQB-82 MQB-82-R (SS316) MQB-G41 MQB-G41-F (HDG)
0.465 0.536 0.529 0.750 0.750 0.807 0.807
13/16" 1-5/8" 1-5/8" 1-5/8" Back-to-Back 1-5/8" Back-to-Back 1-5/8" 1-5/8"
10 10 10 10 10 10 10
00369666 00369668 00304061 00369671 00304063 00369674 00304189
6-5/16"
9-1/16" 6-5/16"
4-3/16"
7/16" x 9/16"
MQP Strut Bases

Attachments to walls, ceilings, floors High application flexibility Reliable and easy to use
Technical Data
MQP
Description
Weight/Piece (lb)
Qty
Item No.
MQV-2/2D-14 Wall and Ceiling MQV-2/2D-14-F Wall and Ceiling (HDG) MQV-2/2D-14-R Wall and Ceiling (SS316) MQP-1/1 Light Duty MQP-1/1-F Light Duty (HDG) MQP-21-72 Standard Duty MQP-21-72-F Standard Duty (HDG) MQP-21-72-R Standard Duty (SS316) MQP-82 1-5/8" Back-to-Back MQP-82-R 1-5/8" Back-to-Back (SS316) MQP-G Pivot Base MQP-45 Base MQP-45-F Base (HDG)
0.966 0.994 0.970 0.243 0.243 2.535 2.535 2.535 4.145 4.145 2.326 0.772 0.722
10 10 10 20 20 12 12 1 8 1 10 10 10
00369639 00304151 00304033 00369646 00304161 00369651 00304165 00304047 00369652 00304048 00369654 00369649 00304164
13/ " x 9/ " 16 16 5/ " 16 5-7/8"
6-1/2" 4-7/16"
4-1/8" 13/ " x 9/ " 16 16
4-7/16"
13/16" x 9/16"
9/ " x 3/ " 16 4 2-3/8" 2-3/8"
1/ " 4
3-1/8"
5-5/16"
7-5/16"
4-3/16"
6"
4-1/8" 45
1-15/16"
3-15/16"
7-7/8"
9/ " 16 1-5/8" 1-5/8"
2-15/16" 2-1/8" 2-15/16" 7-1/2"

239
Strut Accessories
MQZ-L Base plates

Used as heavy plate washer for strut For wall, ceiling or floor attachment of strut, angles, connectors or brackets with Kwik Bolt 3, KB-TZ or HDI anchors For strut nut or spring nut applications with angles, connectors and brackets
Technical Data
Material Finish
MQZ-L
7/ " 16 9/ " 16 11/ " 16
1-13/16" 3/ " 16
Description For Thread Weight/Piece (lb) Qty Item No.
2-1/16"
MQZ-L 3/8 MQZ-L 3/8-F (HDG) MQZ-L 3/8-R (SS316) MQZ-L 1/2 MQZ-L 1/2-F (HDG) MQZ-L 1/2-R (SS316) MQZ-L 5/8
3/8 3/8 3/8 1/2 1/2 1/2 5/8
0.203 0.194 0.194 0.185 0.185 0.185 0.176 (80)
20 20 20 20 20 20 20
00370632 00304200 00304076 00370633 00304201 00304077 00370634
MQZ-SS Strut Tie
Technical Data
Material Finish Rec. tensile load1 Zrec Rec. shear load Qrec
1
MQZ-SS
Carbon steel Electro-galvanized 675 lb (3.0 kN) 1125 lb (5.0 kN) 15 ft-lb (20 Nm)
Tightening torque, MD
1 Rec. loads based on a safety factor of 2.2
Description
Width Across Flats (mm)
Weight/ Piece (lb)
Qty
Item No.
MQZ-SS Locking device For user-assembled B2B strut, use 13 mm socket to set
13 mm
0.006
40
00369691
240

Strut Accessories
MEK Strut End Cap

One size fits all strut profiles Gives a finished appearance while adding protection from sharp edges
Description
Qty
Item No.- Red
Item No. - Gray
MEK - Strut End Cap
50
00244886
00313377
Strut Beam Clamps

For fastening strut to steel beams
3/8"
2-3/16" 3/16"
3" 3-3/8"
Description
Qty
Item No.
BC-A Beam Clamp Assembly Max. Allowable Tensile Load = 1100 lb/pair (Based on a safety factor of 3) SBC 1-5/8" Strut Beam Clamp Max. Allowable Tensile Load = 1200 lb/pair (Based on a safety factor of 3) SBC 2-7/16" to 3-1/4" Strut Beam Clamp Max. Allowable Tensile Load = 1200 lb/pair (Based on a safety factor of 3) MQT-21-41-F Beam Clamp (HDG) Max. Allowable Tensile Load = 1340 lb/pair (Based on a safety factor of 2.2) MQT-21-41-R Beam Clamp (SS316) Max. Allowable Tensile Load = 1340 lb/pair (Based on a safety factor of 2.2) MQT-52-82-R Beam Clamp (SS316) Max. Allowable Tensile Load = 2000 lb/pair (Based on a safety factor of 2.2)
25 25 25 10 10 10
00306570 00258316 00314330 00304190 00304067 00304068

3" 5"
3/8"
2-3/16" 3/16"
Channel and Spring Nuts

Zinc-plated Spring Nuts: for use with 1-5/8" strut
Channel Nut
Description
Qty
Item No.- Spring Nut
Item No. - Channel Nut
Channel/Spring Nut 1/4" Channel/Spring Nut 3/8" Channel/Spring Nut 1/2" Channel/Spring Nut 5/8" Channel/Spring Nut 3/4"
100 100 100 100 100
00258246 00258247 00258248 -
00311937 00311938 00311939 00311940

Spring Nut

241
Pipe Hangers
SLC-EG Speed Lock Clevis Hanger

Unique Speed Lock System eliminates hanger disassembly One piece no lost/dropped nuts and bolts Simple one person installation saves you lift time FM approved and UL, cUL listed Stainless-steel spring on locking device with long-term reliable performance
Technical Data
Size range Material Approvals Factory Mutual (FM) 2" to 8"
SLC-EG
2" to 8" pipe sizes Electro-galvanized carbon steel
Listings Underwriters Laboratories (ULcUL) 2" to 8" Conforms with Federal specifications WW-H-171E (Type 1) Manufacturers Standardization Society MSS-SP-58 (Type 1) Installation Install in accordance with MSS-SP-69
Description
Weight/ Piece (lb)
Pipe Size
RS Rod CL Size
MRI Min. Rod Insertion
Single Item No.
Bulk Item No. Qty
Max Allowable Load (lb)*
RS
SLC-EG 2" SLC-EG 3" SLC-EG 4" SLC-EG 5" SLC-EG 6" SLC-EG 8"
0.32 0.69 1.06 1.33 2.80 3.75
2" 3" 4" 5" 6"
5" 6-7/8" 8-1/2" 9-3/4"
3-9/16" 6-1/8" 7-5/16"
3-5/8" 3/8" 5-7/8" 5/8" 6-9/16" 5/8" 7-7/16" 3/4"
9/16" 3/4" 15/16" 15/16" 1-3/16"
1-1/8" 1-5/16" 1-5/8" 1-3/4"
5/16 7/16 7/16" 9/16"
00334700 00334701 00334702 00334703 00334704 00334705
00337250 50 00337251 50 00337252 20 00337253 20 00337254 10 00337255 10
610 1130 1430 1430 1940 2000

W S H
MRI
5-1/16" 4-13/16" 1/2"
A
CL
11-1/4" 8-15/16"
1-1/16" 1-13/16" 11/16" 2-3/16" 11/16"
8" 13-13/16" 11-3/16" 8-15/16" 3/4"
Open Hanger
Close Hanger
* Maximum allowable loads based on the lower of: 1. Maximum safe load of the threaded hanger rod at rod temperature of 650 F per Manufacturers Standardization Society Standard Practice 58 2. Allowable load for SLC-EG hanger with a safety factor of 3 3. Industry standard for clevis hangers
SDC Clevis Hangers

Standard-duty, electro-galvanized clevis hanger
Technical Data
Application
SDC-EG
Use for the support of stationary, noninsulated pipe lines 1/2" to 14" pipe sizes Electro-galvanized carbon steel
Size range Material
Approvals Factory Mutual (FM) 2-1/2" to 8" Listings Underwriters Laboratories (UL cUL) 2-1/2" to 8" only
Weight/ Piece (lb) Max Allow. Load (lb)1
Description
Pipe Size
RS
CL
MRI
Qty
Item No.
Conforms with Federal specification WW-H-171 (Type 1) Manufacturers Standardization Society MSS-SP-58(Type 1) Installation Install in accordance with MSS-SP-69
SDC-EG 3/4" SDC-EG 1" SDC-EG 1-1/4" SDC-EG 1-1/2" SDC-EG 2" SCC-EG 2-1/2" SDC-EG 3" SDC-EG 4" SDC-EG 5" SDC-EG 6" SDC-EG 8" SDC-EG 10" SDC-EG 12" SDC-EG 14"
0.17 0.19
3/4" 3/8" 1" 3/8"
2-3/8" 2-3/4" 3-5/16" 4-1/2" 5-1/4" 6" 7-3/4" 9-3/4" 11-3/4" 14" 16-1/2" 21-3/4"
1-3/16" 1-1/2" 1-13/16" 2-3/8" 2-11/16" 3" 3-3/8" 4-7/16" 5-7/8" 7-3/16" 8-7/16" 9-9/16" 13"
9/16" 9/16" 9/16" 9/16" 9/16" 3/4" 3/4" 15/16" 1-1/16" 1-1/16" 1-5/16" 1-1/2"
1/4" 5/16" 1/2" 7/8" 15/16" 3/4" 15/16" 1-3/8" 2-5/16" 2-3/4" 2-5/16" 4-3/16"
50 50 25 25 1 25 1 1 1 1 1 1 1 1
00333236 00333237 00424206 00333239 00425681 00333240 00425682 00425683 00424209 00306594 00306595 00424210 00424211 00424212
610 610 610 610 610 1130 1130 1430 1430 1940 2000 3600 3800 4200
0.30 1-1/4" 3/8" 0.40 0.64 0.72 1.17 2.17 3.32 4.90 8.90 12.00 14.80 2" 3/8" 2-1/2" 1/2" 3" 1/2" 4" 5/8" 5" 5/8" 6" 3/4" 8" 3/4" 10" 7/8" 12" 7/8" 14" 1"
0.30 1-1/2" 3/8" 3-15/16"
15/16" 1-13/16"
18-5/8" 10-11/16"
1-5/16" 2-11/16"
1 Based on a safety factor of 3
242

Pipe Hangers
Loop Hangers
Technical Data
Application
Loop Hangers
Pipe support manufactured to use minimum rod sizes permitted by NFPA for fire sprinkler piping 1/2" to 8" pipe sizes Pre-galvanized carbon steel with zincelectroplated insert nut
Size range Material
Approvals Factory Mutual (FM) 1/2 to 8 Listings Underwriters Laboratories (ULcUL) Conforms with Federal Specification WW-H-171 (Type 10) Manufacturers Standardization Society ANSI/ MSS-SP-58 (Type 10) Installation Install in accordance with ANSI/MSS-SP-69
Description
Weight/ Box (lb)
Pipe Size
Rod Size A
Qty
Item No.
Max Allowable Load (lb)1
LH 1/2" LH 3/4" LH 1" LH 1-1/4" LH 1-1/2" LH 2" LH 2-1/2" LH 3" LH 4" LH 6 LH 8"
7 7 8.25 10 10 10 30 16 16.5 5 22.5
1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2 3" 4" 6" 8"
3/8" 3/8" 3/8" 3/8 3/8" 3/8" 3/8" 3/8" 3/8" 1/2" 1/2"
2-3/4" 3-1/16" 3-5/16" 3-9/16" 3-13/16" 4-1/4" 5-9/16 6-9/16" 7-9/16" 11-5/16" 12-7/8"
2-5/16" 2-1/2" 2-5/8" 2-11/16" 2-13/16" 3-1/16" 3-15/16" 4-5/8 5-3/16" 7-7/8" 8-7/16"
1-1/16" 1-1-16" 1-1/16" 1" 1 1" 1-5/8" 2" 2-1/16" 3-7/16" 3"
100 100 100 100 100 100 100 50 50 20 15
00257353 00257354 00337820 00257356 00257357 00257358 00257359 00257360 00257362 00257364 00257365
300 300 300 300 300 300 525 525 650 1000 1000
1 Based on a safety factor of 3.5
Insulation Shields
Technical Data
Application
Insulation Shields
Shield for use with the standard-duty clevis hangers (SDC) Pre-galvanized carbon steel
Material
Description
ID
Guage
Weight per Piece (lb)
Qty
Item No.
Insulation Shield 2" Insulation Shield 2-1/2" Insulation Shield 3" Insulation Shield 4" Insulation Shield 5" Insulation Shield 6" Insulation Shield 8" Insulation Shield 10"
2-1/2" 3" 3-5/8" 4-5/8" 5-9/16" 6-5/8" 8-3/8" 10-3/4"
18 18 18 16 16 16 16 16
12" 12" 12" 12" 12" 12" 12" 18"
0.70 0.84 1.01 1.28 1.60 1.90 3.05 5.63
1 1 1 1 1 1 1 1
00424197 00424198 00424199 00424200 00424202 00424203 00424204 00424205

243
Beam Clamps
BC Beam Clamp

To secure channel installations to steel beams No drilling or welding necessary Each set for an installation is completely pre-assembled and suits all usual sizes of I-beams Flexibility and no loss of spare parts
Technical Data
Application
MKL
Structural attachment with infinite adjustment to top or bottom of metal beams, purlins, channel or angle iron to support hanger rod 1/4" to 3/4" rod sizes ASTM A536 ductile iron casting with a hardened cup point set screw and locknut Plain or electrogalvanized
Size range Material
Finish
Approvals Factory Mutual (FM) 3/8" thru 1/2" Listings Underwriters Laboratories (UL cUL) 3/8" thru 3/4" Conforms with Federal specification WW-H-171 (Type 19) Manufacturers Standardization Society MSS-SP-58 (Type 19) Installation Install in accordance with ANSI/MSS-SP-69
Note: Set screw must be tightened onto the sloped side of the I-Beam, channel or angle iron flange. Required torque values for the set screw are as shown in the table
Description
Min. Set-Screw Torque (ft-lb)1
Max. Set-Screw Torque (ft-lb)1
Rod Size
Max. Pipe Size
Maximum Allowable Load (lb)2 Box Qty Item No. Top Flange Bottom Flange
BC 3/8" BC 1/2" BC 5/8" BC 3/4" BC-EG 1/4" BC-EG 3/8" BC-EG 1/2"
5.0 5.0 10.0 10.0 3.5 5.0 5.0
7.5 7.5 15.0 15.0 5.0 7.5 7.5
3/8" 1/2 5/8" 3/4" 1/4" 3/8" 1/2"
4" 8" 8" 8" 4" 8"
100 50 50 50 100 100 50
00257366 00257367 00257368 00257369 00258002 00306600 00306601
500 950 950 950 250 500 950
250 760 760 760 100 250 760
CAUTION! Correct torquing is essential for proper clamp performance 1 Note: In the absence of a torque wrench: MINIMUM: The set-screw should be finger tightened to the I-Beam and then an additional one-third turn applied to the set-screw MAXIMUM: The set-screw should be finger tightened to the I-Beam and then an additional one-half turn applied to the set-screw 2 Based on a safety factor of 3
BC-WM Wide Mouth Beam Clamp
Technical Data
Application
BC-WM
Structural attachment with infinite adjustment to top or bottom of roll formed, large lipped metal beams, purlins, channel or angle iron which require a 1-1/4" maximum jaw opening 3/8" and 1/2" rod sizes ASTM A536 ductile iron casting with a hardened cup point set screw and locknut Electro-galvanized
Size range Material
Alternate finish Approvals Factory Mutual (FM)

Maximum Allowable Load (lb)2 Box Qty Item No. Top Flange Bottom Flange
Listings Underwriters Laboratories (UL cUL) Conforms with Federal specification WW-H-171 (Type 19) Manufacturers Standardization Society MSS-SP-58 (Type 19) Installation Install in accordance with ANSI/MSS-SP-69
Note: Set screw must be tightened onto the sloped side of the I-Beam, channel or angle iron flange. Required torque values for the set screw are as shown in the table
Description
Torque (ft-lb)
Rod Size
Max. Pipe Size
BC-WM 3/8" BC-WM 1/2"
5.0 10.0
3/8" 1/2"
4" 8"
50 50
00306602 00306603
500 950
250 760
244

Beam Clamps
Steel C-Clamp with Lock Nut
Technical Data
Application
C-Clamp
Structural attachment to metal beams, purlins, or angle iron for the support of hanger rod 3/8" to 5/8" rod Carbon steel with hardened steel cup point set screw and lock nut
Range Material
Approvals Factory Mutual (FM) Listings Underwriters Laboratories (UL) Conforms with Federal specification WW-H-171 (Type 23) Manufacturers Standardization Society MSS-SP-58 (Type 23). Installation1 Install in accordance with ANSI/MSS-SP-69
Note: Set screw must be tightened onto the sloped side of the I-Beam, channel or angle iron flange. Required torque values for the set screw are as shown in the table Torque (ft-lb Rod Size Max. Pipe Size Minimum Rod Insertion Maximum Allowable Load (lb)2
Description
Qty
Item No.
C-Clamp w/ Lock Nut 3/8" C-Clamp w/ Lock Nut 1/2"
5.0 10.4
3/8" 1/2"
4" 8"
13/16" 13/16"
2-5/16" 2-5/16"
100 50
00306571 00306572
400 500
Retainer Straps
Technical Data
Application
Retainer Straps
To be used when a retainer strap is specified for the BC and BC-WM beam clamps Pre-galvanized carbon steel
7/16" hole
9/16" hole
Material
Note: Field bend and use jam nut over hanger to secure
Description
Length (in)
Qty
Item No.
3/8" Retainer Strap
12"
00424238

245
Split Rings
Split Rings Electro Galvanized

For suspending uninsulated stationary pipe. Allows for piping runs close to ceilings or walls
Technical Data
Material
ElectroGalvanized
Malleable iron body, carbon steel rivet and bolt
Conforms with Federal specification WW-H-171 (Type 25) Manufacturers Standardization Society MSS-SP-58 (Type 12)
Weight/ Piece (lb) Rod Size (RS) Center Line (CL) Min. Rod Insertion (MR) Maximum Allowable Load (lb)1
Installation Install in accordance with ANSI/MSS-SP-69
Description
Pipe Size
Qty
Item No.
SR-EG 1/2" SR-EG 3/4" SR-EG 1" SR-EG 1-1/2" SR-EG 2"
0.18 0.22 0.23 0.34 0.37
1/2" 3/4" 1" 1-1/2" 2"
3/8" 3/8" 3/8" 3/8" 3/8"
16/16" 1-5/16" 1-1/16" 1-3/16" 1-7/16"
3/8" 3/8" 3/8" 3/8" 3/8"
100 100 100 50 50
00306630 00306631 00306632 00306633 00306634
180 180 180 180 180
Split Rings Copper

For suspending uninsulated stationary copper tubing. Allows for piping runs close to ceilings or walls
Technical Data
Material
Copper
Malleable iron body, carbon steel rivet and bolt with copper electroplate finish
Conforms with Federal specification WW-H-171 (Type 25) Manufacturers Standardization Society MSS-SP-58 (Type 12)
Weight/ Piece (lb) Pipe Size Rod Size (RS) Center Line (CL) Min. Rod Insertion (MR) Maximum Allowable Load (lb)1
Installation Install in accordance with ANSI/MSS-SP-69

Note: This pipe support is not designed for corrosion or electrolysis resistance. Copper plating is for identification purposes only
Description
Qty
Item No.
Copper SR 1/2" Copper SR 3/4" Copper SR 1" Copper SR 1-1/4" Copper SR 1-1/2" Copper SR 2"
0.18 0.22 0.23 0.25 0.34 0.37
1/2" 3/4" 1" 1-1/4" 1-1/2" 2"
3/8" 3/8" 3/8" 3/8" 3/8" 3/8"
11/16" 13/16" 15/16" 1-1/16" 1-3/16" 1-7/16"
3/8" 3/8" 3/8" 3/8" 3/8" 3/8"
100 100 100 100 100 50
00306623 00306624 00306625 00306626 00306627 00306628
180 180 180 180 180 180
246

Riser Clamps
Riser Clamps Electro Galvanized

For supporting vertical steel pipe risers, utilizing the structure to support the legs on each end of the clamp. Normally rests on the floor through which riser passes. Use welded lugs on pipe above clamp for greater loads
Technical Data
Electro Galvanized
Conforms with Federal specification WW-H-171 (Type 8) Manufacturers Standardization Society MSS-SP-58 (Type 8) Installation Install in accordance with ANSI/MSS-SP-69
Other sizes available by special order
Description
Weight/Piece (lb)
Pipe Size
Qty
Item No.
Maximum Allowable Load (lb)1
RC-EG 1" RC-EG 1 1/4" RC-EG 1 1/2" RC-EG 2" RC-EG 2 1/2" RC-EG 3" RC-EG 4" RC-EG 6" RC-EG 8"
1.05 1.10 1.16 1.33 2.20 2.34 3.33 7.45 9.90
1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" 6" 8"
9" 9-7/16" 10" 10 1/4" 11" 11-3/4" 13" 16" 18-1/4"
25 25 25 25 25 1 1 1 1
00336347 00336348 00336349 00424225 00336351 00424226 00424227 00424228 00424229
255 255 255 300 400 500 750 1400 2200
Riser Clamps Copper

For supporting vertical copper pipe risers, utilizing the structure to support the legs on each end of the clamp
Technical Data
Copper
Conforms with Federal specification WW-H-171 (Type 8) Manufacturers Standardization Society MSS-SP-58 (Type 8) Installation Install in accordance with ANSI/MSS-SP-69
Note: This pipe support is not designed for corrosion or electrolysis resistance. Copper plating is for identification purposes only
Description
Weight/Piece (lb)
Pipe Size
Qty
Item No.
Maximum Allowable Load (lb)1
RC-Copper 1" RC-Copper 1-1/4" RC-Copper 1-1/2" RC-Copper 2" RC-Copper 2-1/2" RC-Copper 3" RC-Copper 4"
0.78 1.13 1.22 1.32 1.45 1.60 1.73
1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4"
9-1/4" 9-1/2" 9-1/2" 10-3/8" 11" 12" 12-1/2"
25 25 25 25 25 25 25
00424231 00424232 00424233 00424234 00424235 00424236 00424237
120 150 150 150 300 300 300

247
Strut Clamps
Strut Clamp Copper Plated

Copper plated strut clamps for copper tubing NOTE: This hanger is not designed for corrosion or electrolysis resistance Copper plating is for identification purposes only
Description
Qty
Item No.
Strut Clamp Copper 1/4" Strut Clamp Copper 3/8" Strut Clamp Copper 1/2" Strut Clamp Copper 3/4" Strut Clamp Copper 1" Strut Clamp Copper 1-1/4" Strut Clamp Copper 1-1/2" Strut Clamp Copper 2" Strut Clamp Copper 2-1/2" Strut Clamp Copper 3" Strut Clamp Copper 4"
100 100 100 100 100 100 100 50 50 25 25
00371544 00371545 00371546 00371547 00371548 00371549 00371550 00371551 00371552 00371553 00371554
Strut Clamp Rigid

For use with rigid pipes
Description
Qty
Item No.
Strut Clamp Rigid 1/2" Strut Clamp Rigid 1/2" (SS316) Strut Clamp Rigid 3/4" Strut Clamp Rigid 3/4" (SS316) Strut Clamp Rigid 1" Strut Clamp Rigid 1" (SS316) Strut Clamp Rigid 1-1/4" Strut Clamp Rigid 1-1/4" (SS316) Strut Clamp Rigid 1-1/2" Strut Clamp Rigid 1-1/2" (SS316) Strut Clamp Rigid 2" Strut Clamp Rigid 2" (SS316) Strut Clamp Rigid 2-1/2" Strut Clamp Rigid 2-1/2" (SS316) Strut Clamp Rigid 3" Strut Clamp Rigid 3" (SS316) Strut Clamp Rigid 4" Strut Clamp Rigid 4" (SS316) Strut Clamp Rigid 6" Strut Clamp Rigid 8"
100 50 100 50 100 50 50 25 50 25 50 25 25 10 25 10 25 10 10 10
00371557 00424215 00371558 00424216 00371559 00424217 00371560 00424218 00371561 00424219 00371562 00424220 00371563 00424221 00371564 00424222 00371565 00424223 00424213 00424214
Strut Clamp EMT

For use with electrical-mechanical tubing
Description
Outside Diameter (in)
Qty
Item No.
Strut Clamp EMT 1/2" Strut Clamp EMT 3/4" Strut Clamp EMT 1" Strut Clamp EMT 1-1/4" Strut Clamp EMT 1-1/2" Strut Clamp EMT 2"
0.706" 0.922" 1.163" 1.510" 1.740" 2.197"
100 100 100 50 50 50
00371568 00371569 00371570 00371571 00371572 00371573
248

Threaded Accessories
Strut Clamp Universal

For use with rigid pipe or electricalmechanical tubing
Description
Outside Diameter (in)
Qty
Item No.
Strut Clamp Universal 1/2" Strut Clamp Universal 3/4" Strut Clamp Universal 1" Strut Clamp Universal 1-1/4" Strut Clamp Universal 1-1/2" Strut Clamp Universal 2"
0.773" 0.986" 1.239" 1.585" 1.820" 2.286"
100 100 50 50 50 50
00371574 00371575 00371576 00371577 00371578 00371579
Eye Coupler

A structural attachment used to join hanger rod to a structure
Technical Data
Materials Approval Factory Mutual (FM)
Eye Coupler
Pre-galvanized carbon steel
Listing Underwriters Laboratories (ULcUL)
Description
Rod Size (RS)
HS1
HS2
Minimum Rod Insertion (MR)
Max Pipe Size
Qty
Item No.
Max Allowable Load (lb)*
Eye Coupler 3/8"
3/8"
2-1/4"
1/2"
1/4"
1-1/8"
1-1/8"
4"
250
00258317
250
*Capacity of eye coupler loaded axially. Based on safety factor of 3. RS
Offset Eye Coupler

A structural attachment used to join hanger rod to a structure. Provides unlimited vertical rod adjustment
Technical Data
Size range Material Approval Factory Mutual (FM)
Offset Eye Coupler

3/8" rod size Pre-galvanized carbon steel
Listing Underwriters Laboratories (ULcUL)

RS
Rod Minimum Insertion (MR) Max Allowable Load (lb)*
Description
Rod Size (RS)
HS1
HS2
Max Pipe Size
Box Qty
Item No.
Offset Eye Coupler 3/8"
3/8"
3-1/8"
1/2"
1/4"
1-3/16"
1-1/8"
4"
250
00258318
250
*Capacity of offset eye coupler loaded axially. Based on safety factor of 3.

249
Threaded Rod
Technical Data
Materials
Threaded Rod
Carbon Steel, Stainless Steel 316/ ASTM A276 Class 1 Plain and zinc electroplated to ASTM B 633-98, SC 1 Type I
Finishes
Weight per bundle (lb) Qty (Bundle)
Description
Item No.
Threaded Rod 1/4" x 6' (Zinc) Threaded Rod 1/4" x 10' (Plain) Threaded Rod 1/4" x 10' (Zinc) Threaded Rod 1/4" x 12' (SS316) Threaded Rod 3/8" x 6' (Plain) Threaded Rod 3/8" x 6' (Zinc) Threaded Rod 3/8" x 10' (Plain) Threaded Rod 3/8" x 10' (Zinc) Threaded Rod 3/8" x 12' (SS316) Threaded Rod 1/2" x 6' (Zinc) Threaded Rod 1/2" x 10' (Plain) Threaded Rod 1/2" x 10' (Zinc) Threaded Rod 1/2" x 12' (SS316) Threaded Rod 5/8" x 10' (Plain) Threaded Rod 5/8" x 10' (Zinc) Threaded Rod 5/8" x 12' (SS316) Threaded Rod 3/4" x 6' (Zinc) Threaded Rod 3/4" x 10' (Plain) Threaded Rod 3/4" x 10' (Zinc) Threaded Rod 3/4" x 12' (SS316)
35.70 59.50 59.50 14.26 42.60 42.60 71.30 71.30 34.01 38.80 61.40 61.40 64.59 66.50 66.50 49.68 36.20 60.00 60.00 72.31
50 50 50 10 25 25 25 25 10 12 12 12 10 8 8 5 5 5 5 5
00257963 00309391 00309386 00411724 00257969 00257964 00309392 00309387 00411742 00257965 00309393 00309388 00411743 00309394 00309389 00411744 00257967 00309395 00309390 00411745 Stainless Steel 316/ASTM A276 Class Rod Size 1/4" 3/8" 1/2" 5/8" 3/4" Ultimate Tensile Load (lb)1 1345 3406 6298 10,078 15,070 Weight lb/ft 0.12 0.28 0.54 0.83 1.21 Carbon Steel Rod Size 1/4" 3/8" 1/2" 5/8" 3/4" Ultimate Tensile Load (lb)1 1345 3406 6298 10,078 15,070 Weight lb/ft 0.12 0.30 0.50 0.84 1.20
1 Based on MSS-SP 58
1 Based on MSS-SP 58
Rod Couplers
Technical Data
Materials
Rod Couplings
ASTM A563, Grade A carbon steel; Stainless Steel 316 Zinc electroplated to ASTM B 633-98, SC 1, Type I Class 2A fit; Class 2B thread
Finish
Thread
Description Length Width across flats Qty Item No.
1/4" Rod Coupler 1/4" Rod Coupler (SS316) 3/8" Rod Coupler 3/8" Rod Coupler (SS316) 1/2" Rod Coupler 1/2" Rod Coupler (SS316) 5/8" Rod Coupler 5/8" Rod Coupler (SS316) 3/4" Rod Coupler
7/8" 7/8" 1-1/8" 1-1/8" 1-1/4" 1-1/4" 2-1/8" 1-3/4" 2-1/4"
3/8" 3/8" 1/2" 1/2" 5/8" 5/8" 13/16" 7/8 " 1"
1000 100 500 50 500 50 300 50 200
00257983 03445335 00257984 03445336 00257985 03445337 00257986 03445338 00257987
250

Hex Nuts
Technical Data
Materials Dimensions Finish
Nuts
ASTM A 563 Grade A; Stainless Steel 316 ASME/ANSI B18.2.2 1986 ASTM B 633-98, SC 1 Type I Class 2A fit; Class 2B thrd; ASME B1.1
Description
Width Across Flats
Qty
Item No.
Thread
Hex Nut-Heavy 1/4" Hex Nut-Standard 1/4" (SS316) Hex Nut-Heavy 3/8" Hex Nut-Standard 3/8" (SS316) Hex Nut-Heavy 1/2" Hex Nut-Standard 1/2" (SS316) Hex Nut-5/8" Hex Nut-Standard 5/8" (SS316) Hex Nut-3/4" Hex Nut-Standard 3/4" (SS316)
1/2" 7/16" 11/16" 9/16" 7/8" 3/4" 15/16" 15/16" 1-1/8" 1-1/8"
1000 100 1000 100 1000 100 250 50 250 50
00335549 03445340 00335550 03445341 00335551 03445342 00336402 03445343 00336403 03445344
Washers
Technical Data
Washers
AISI 1005 through 1035; Stainless Steel 316 ASME/ANSI B18.22.1 Type A - 1986 ASTM B 633-98, SC 1 Type I
Description
Inside Diameter
Outside Diameter
Qty
Item No.
Washer 1/4" Washer 1/4" (SS316) Washer 3/8" Washer 3/8" (SS316) Washer 1/2" Washer 1/2" (SS316) Washer 5/8" Washer 5/8" (SS316) Washer 3/4" Washer 3/4" (SS316) Fender Washer 1/4" Fender Washer 1/4" (SS316) Fender Washer 3/8" Fender Washer 3/8" (SS316) Fender Washer 1/2" Fender Washer 1/2" (SS316)
0.312 0.281 0.438 0.406 0.562 0.531 0.656 0.656 0.812 0.812 0.281 0.281 0.406 0.406 0.531 0.531
0.734 0.625 1.000 0.875 1.375 1.250 1.312 1.312 1.469 1.500 1.250 1.250 1.500 1.500 2.000 2.000
1000 100 1000 100 1000 100 250 50 250 50 1000 100 1000 100 1000 100
00335552 03445345 00335553 03445346 00335554 03445347 00336404 03445348 00336405 03445349 00313068 03445350 00313069 03445351 00313070 03445352
Hex Head Bolts
9
Technical Data
Hex Head Bolts

ASTM A 307; Stainless Steel 316 ASME/ANSI B18.2.1 1981 Zinc electroplated to ASTM B 633-98, SC 1, Type I Class 2A fit; Class 2B thrd; ASME B1.1
Description
Qty
Item No.
Hex Head Bolt 3/8" x 1-1/4" Hex Head Bolt 3/8" x 1-1/4" (SS316) Hex Head Bolt 3/8" x 1-1/2" Hex Head Bolt 3/8" x 1-1/2" (SS316) Hex Head Bolt 1/2" x 1" Hex Head Bolt 1/2" x 1" (SS316) Hex Head Bolt 1/2" x 1-1/4" Hex Head Bolt 1/2" x 1-1/4" (SS316) Hex Head Bolt 1/2" x 1-1/2" Hex Head Bolt 1/2" x 1-1/2" (SS316)
500 50 500 50 250 50 250 50 250 50
00311951 03445353 00311952 03445354 00311953 03445355 00311954 03445356 00311955 03445357
Thread

251
Seismic Hinges and Stiffeners
Seismic Hinges
Description
Hanger Rod/ Bolt Diameter
Qty
Item No.
Seismic Hinge, Strut Half w/ Bolt & Nut Seismic Hinge, Base/ Hanger Half, 3/8" Seismic Hinge, Base/ Hanger Half, 1/2" Seismic Hinge, Base/ Hanger Half, 5/8" Seismic Hinge, Base/ Hanger Half, 3/4"
1/2" 3/8" 1/2" 5/8" 3/4"
10 10 10 10 10
00333309 00369714 00333308 00369715 00369716
Vertical Rod Stiffeners
Internal
Description
Hanger Rod/ Bolt Diameter
Qty
Item No.
Hilti Rod Stiffener Internal (rod in strut)
3/8"5/8"
25
00311943
Cast-In Strut and Insert

Cast-In Strut
Description
Qty Item No.
Cast In Strut 1 3/8" x 12 ga x 20' Cast In Strut 13/16" x 12 ga x 20'
10 10
3448648 3448649
Concrete Insert
Description
Qty Item No.
Concrete Insert EG
25
03442103
Square Nut for Insert

Description Qty Item No.
Insert Nut 1/4" Insert Nut 3/8" Insert Nut 1/2" Insert Nut 5/8"
Note Available on special order basis. Please contact Hilti for pricing and delivery. Not returnable.
100 100 100 100
3448644 3448645 3448646 3448647
252

MI Industrial Support System
Industrial supports: Simple, flexible, strong.

Innovative
Because the Hilti MI system does not require welding, worker safety in flame and gas-sensitive areas is improved. In addition, the standardized, modular components bolt together quickly and easily and offer load values equal to or higher than similar welded systems. As the Hilti MI system is modular, setting new layouts around permanent structures is easy. Likewise, existing Hilti MI systems are easily reconfigured to meet your changing needs. Once the new layout is determined, simply unbolt existing components; add, delete or relocate pieces as needed; bolt the new configuration together and apply load. It's that easy! The modular nature of the Hilti MI Industrial Support System helps reduce planning and installation time. Because each piece is light-weight and reusable, there is no need for heavy equipment and nothing needs to be thrown away, adding to overall system efficiency and potential savings to your bottom line.
The safe, four-part system for industrial applications

The Hilti MI Industrial Support System is an industrial support system designed with strength, durability and flexibility in mind. This innovative support system is ideal for pipe systems, cable trays, duct runs, electrical panel boxes, shelters, overhead medical room supports and more.
Pipes
Cable Trays
Duct Systems
Panel Box
Operating Rooms
254

Flexible
Easy installation, reconfiguration and extension Easy as built tolerance compensation Integrates with Hiltis MQ Strut System
Efficient
Only four part types Fast, easy installation part by part, onsite by one or two workers No welding means no downtime in hot danger zones
Economical
All parts are reusable Up to 50% lighter, no special lifting equipment required Hot dip galvanized, no need to paint
Safe
State-of-the-art connection types Corrosion and dynamic load resistant Torsion-resistant profile design
9
Girders Girder Connectors Steel Connectors Concrete Connectors
MI-90 and MI-120 girder sizes for medium and heavy duty applications are resistant to horizontal and vertical bending stresses as well as torsion effects. Add light duty System MQ and you have all load classes covered!
Using spaces in the girders, System MI connectors are adjustable by up to 2" on the first installation, and can be fine adjusted by 3/16". All connectors are packaged with fastening parts for convenience.
Connections to steel are made using reliable beam clamps. The base plates are designed to cover a large range of standard steel profiles up to 12". Girder clamping accomodates steel profiles >12".
Concrete connector baseplates can be fastened using a variety of Hilti anchors for the safest hold. Choose from metal and chemical anchors according to loading and base material conditions.

255
MI Modular Components
Girder
Girder
Connector
Connector
Connector
MI-90 3m MI-90 6m
00304798 00304799
MI-120 3m MI-120 6m
00304800 00304801 MIC-90-U 00304803 MIC-120-U 00304804 MIC-90-L 00304805
Bases for connecting to concrete
1" (25) x 9/16" (14)
MIC-C90-AA
00304825
MIC-C90-U
00304826
MIC-CU-MA
00304828
MIC-C90-D
00304827
MIC-C120-D
00304829
Bases for connecting to steel beams
Beam Clamp
MIC-S90-A MIC-S90-B MIC-S90-AA 00304811 MIC-S90-C
00304812 00304813 00304814
MIC-S120-A MIC-S120-B MIC-S120-C
00304818 00304819 00304820
MIC-SA-MA MIC-SB-MA MIC-SC-MA
00304815 00304816 00304817 MI-GC-M12 00233859
MI connectors/braces (application)
MI/MQ Connector
Accessory
Self-Locking Collar Nut MIC-T 00304807 MIC-U-MA 00340806 Cantilever brace MIC-MI/MQ-X 00304881 M12-F Hex. Collar Nut 00382397
Application examples
Pos. 2
Pos. 1
Pos. 1
Pos. 4
Pos. 3
Pos. 3
Pos. 5 Pos. 4
Pos. 5
Pos. 2
Connection to steel beam Flange width <12-1/2"
Connection to steel beam Flange width >12-1/2"
U-Frame
Loraine Cross
U-Bolt Fastening
256

Case Study: With the Hilti MI system they saved 77 % of working time and 24% of total costs compared to welded structures.
Total time (Assembly and installation)
1802 hrs 17 min
Total costs (Pre-fabricated structure and installation)

600500$ Dollars
$637
Minutes
120-
15 24 -77% 98
31.5 min
4003002001000-
51 160 426
$482
-24%
39 91 352
60-
3 16 12.5
Steel Hilti MI System
0-
Steel
Hilti MI System
Assembly*
Installation
Corrosion protection
Material cost
Labor cost**
Rework / scrap***
* Labor Steel: 1 general, 1 welder Hilti MI: 2 general
** Basis labor wage: 20 $/h general; 50 $/h welder *** Basis 12% scrapping costs (pre-fab. construction)
Comparison Data
Weight of structure Installation time (assembly and installation 2 laborers) Material costs Material costs for the structure Total costs (material + labor + scrap) Labor time spent on entire project (includes anchoring)
Welded Steel
212.9 lb 137 min $2.00/lb $426 $637 4.6 hrs
MI System
89.2 lb 31.5 min $352 $482 1 hr
Difference
-58% -77% -17% -24% -78%
For additional infomation, please refer to the following Hilti publications. Contact Hilti to request a copy.
Hilti MI/MQ Product Catalog A Guide to Specification and Installation
Hilti MI Technical Guide Industrial Modular Support System

257

SOPORTERIA

Uploaded by

Copyright:

Available Formats

SOPORTERIA

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SOPORTERIA

Uploaded by

Copyright:

Available Formats

Installation Systems

Hilti. Outperform. Outlast.

B2B Strut and Brackets . . . . . . . . . 233

Angles and Connectors . . . . . . . . . 237

Splice Plates, Clamps and Bases . . . . . . . . . 238

Strut Accesories . . . . . . . . . 240

Pipe Hangers . . . . . . . . . 242

Beam Clamps . . . . . . . . . 244

Split Rings . . . . . . . . . 246

Riser Clamps . . . . . . . . . 247

Strut Clamps . . . . . . . . . 248

Threaded Accessories . . . . . . . . . 250

Seismic Hinges, Stiffeners and Cast-In Systems . . . . . . . . . 252

MI Industrial Support System . . . . . . . . . 253

Hilti. Outperform. Outlast.

Hilti Strut (12 and 14 ga)

Features and Applications

Strut 13/16 in-12 gauge

Strut 1-5/8 in-12 gauge

Strut 2-7/16 in-12 gauge

Strut 13/16 in-14 gauge

Strut 1-5/8 in-14 gauge

Material / Finishes Pre-Galvanized

Hot Dipped Galvanized

Hilti. Outperform. Outlast.

Strut and Brackets

Back-to-Back Strut (12 ga)

Features and Applications

Strut 13/16 in-12 gauge back-to-back

Strut 13/16 in-12 ga/PG (10 ft 1 in) B2B

Strut 1-5/8 in-12 gauge back-to-back

1-9/16 in x 9/16 in 1-9/16 in x 9/16 in 1-9/16 in x 9/16 in

35.9 80.8 35.9

03424515 03424517 03424529

Features and Applications

MQK-21/300 MQK-21/450 MQK-21/450-F HDG

11-13/16 in 17-11/16 in 17-11/16 in

300 450 450

14/2 14/2 14/2

1.48 1.96 1.96

00369607 00369608 00304114

MQK-41/3/300 MQK-41/3/600 MQK-41/600-F HDG MQK-41/600-R SS316 Ti

11-13/16 in 23-5/8 in 23-5/8 in 23-5/8 in

300 600 600 600

12/3 12/3 14/2 14/2

2.62 4.54 3.46 3.46

00370595 00370597 00304117 00304007

Hilti. Outperform. Outlast.

Features and Applications

Tightening Torque MD (ft-lb) 30 30 30

MQN MQN-F (HDG) MQN-R (SS316)

0.145 0.185 0.170

00369623 00387779 00304012

Press and turn.

Tighten using 11/16" socket.

Total Installation Cost Using Current Practices Current Practices

Hilti. Outperform. Outlast.

MQM Wing Nut

Features and Applications

Tightening Torque MD (ft-lb) 7 15 30 15 30 7 15 30