LuK Repair Solution

for Dry Double Clutches

Removal and Installation
Special Tool/Damage Diagnostics
Alfa Romeo, Fiat, Jeep, Suzuki C635 DDCT 6-speed transmission
 The content of this brochure is not legally binding and Copyright ©
is solely intended for information purposes. Schaeffler Automotive Aftermarket GmbH & Co. KG
Where legally permissible, all liability on the part of February 2021
Schaeffler Automotive Aftermarket GmbH & Co. KG
devolving in connection with this brochure is excluded.

All rights reserved. Any reproduction, distribution,

communication, public reproduction, or other publi-
cation of this brochure in its entirety or in part is not
permitted without prior written consent from Schaeffler
Automotive Aftermarket GmbH & Co. KG.

2
Schaeffler in the Automotive Aftermarket –
more innovation, more quality and more service.

Schaeffler REPXPERT –
the service brand for garage professionals.
With REPXPERT, we offer a comprehensive service
package for our products and repair solutions. Looking
for specific information about damage diagnosis? Are
you in need of particular tools to help make your every-
day garage routine easier? Whether online portal,
service hotline, installation instructions and videos,
training seminars, or events – you get all technical
services from a single source.
Register now for free, in just a few clicks, at:
www.repxpert.com.

Schaeffler in the Automotive Aftermarket –

always the first choice for vehicle repair.
Whenever a vehicle needs to go to the garage, our
products and repair solutions are first choice to fix
them. With our system competence in transmission,
engine, and chassis, we are a reliable partner around
the world. Whether passenger cars, light and heavy
commercial vehicles, or tractors – our optimally tuned
components allow fast and professional parts re-
placement.

Our products are based on a comprehensive systems

approach. Innovation, technical expertise, and the
highest material and manufacturing quality make us
not only one of the leading development partners for
vehicle manufacturers, but also a pioneering provider
of value-retaining spare parts and complete repair
solutions for clutches and clutch release systems,
engine and transmission applications, and chassis
applications in original-equipment quality – right up
to the appropriate special tools.

For over 50 years, we have offered everything needed

for transmission repair under the LuK brand. Besides
the LuK RepSet family and products for the entire
hydraulic release system for professional clutch repair,
the portfolio also includes the dual mass flywheel and
components for expert repair of transmissions and
differentials. It also includes professional solutions
for transmission repair of commercial vehicles and
tractors.

3
4
 Contents

Contents
Page

1 Diagnostics 6

1.1 General information about the system 6

1.2 Emergency release 6

1.3 Wear test 7

1.4 Visual inspection 7

1.5 Noise 7

1.6 Troubleshooting with the diagnostic device 7

2 Description and scope of delivery for the LuK RepSet 2CT 8

3 Description and scope of delivery for the LuK special tool 9

4 Removal and installation of the double clutch 10

4.1 Repair instructions 11

4.2 Removal of the double clutch 12

4.3 Installation of the double clutch 18

5 Instructions for the Dual Mass Flywheel (DMF) 27

6 DMF versions 28

7 DMF reset tool KL-0500-721 29

8 Resetting the anti-backlash ring of the DMF 31

9 Installation and initial operation 37

5
1 Diagnostics

1 Diagnose
1.1 General Information about the System 1.2 Emergency Release

Before repairing the double clutch, some fundamental Manually Unlocking the Selector Lever (for example)
questions must be clarified with the customer in order In the event of malfunctions in the electrical system or
to narrow down the error pattern as precisely as possible. a discharged battery, the gear selector lever is blocked.
To move the vehicle, the gear selector lever must be
If the vehicle is still drivable, we recommend carrying un­locked manually and moved out of the P position. To
out a test drive. The customer should be driving the this end, a corresponding mechanism located under
vehicle whilst pointing out any problems. the shift lever sleeve must be operated.

Specific Questions for the Customer:

• What exactly does not work or what are the
symptoms?
• How long has the problem existed?
• Did the problem start suddenly or did it develop
gradually (slowly)?
• How often does the problem occur:
sporadically, often or always?
• In which driving condition does the problem occur:
e.g, when starting, accelerating or decelerating,
when the engine is cold or warm?
• What is the mileage of the vehicle?
• Is the vehicle subjected to extraordinary loads? The shift lever can be unlocked using a push button
E.g, towing a trailer, high load capacity, frequent
hill climbs, operated as a taxi, fleet car, rental car,
driving school? Manually Unlocking the Ignition Key (for example)
• What is the driving profile: The key is blocked in the event of malfunctions or lack of
urban traffic, short journeys, intercity, highway? power supply. The key cannot be removed from the lock.
• Have repairs already been carried out on the clutch/ To remove the ignition key, insert a screwdriver into
transmission system? the dedicated opening of the steering column housing.
If so, at what mileage? Gently press to unlock the locking device.
What was the cause of that complaint?
What repairs were carried out?

Inspections on the Vehicle

At the beginning of removal work, it is recommended
that the following points are checked:

• Defect code entries in the control unit (engine,

transmission, clutch, comfort, CAN bus etc.)
• Battery power

Warnings in the Event of System Malfunctions

A warning light in the instrument panel lights up in the
event of malfunctions, operator errors or if the clutch
overheats. In the event of serious errors, an acoustic The locking device for the ignition key can be overridden using a
signal sounds as well. Notes on the respective warnings screwdriver
are included in the vehicle handbook.

6
1.3 Wear Test 1.6 Troubleshooting with a Diagnostic
Device

A wear test is not possible while the clutch is installed. You can diagnose the transmission electronics and
The permanent monitoring system for the transmission clutch electronics. Prior to each repair, the contents
and clutch electronics indicates wear-related errors of the error memory must be read using a suitable
directly in the instrument cluster. diagnostic tool and, if possible, retained as a print-out.
The error memory report provides an initial overview
1.4 Visual Inspection of the system errors and forms the basis for further
repair measures. The report provides the data required
Prior to each repair, the area of the clutch system must to assess the error pattern (important when contacting
be checked for leaks and damage as a matter of course. the LuK INA FAG Service Center or in case of a warranty
Damage caused by parts that have broken off or oil leaks claim).
due to defective seals or sealing rings must be rectified
before the clutch is replaced. If the clutch is oily, it must Once the double clutch has been replaced, a basic
be replaced. adjustment of the clutch system is required using the
appropriate diagnostic tool, as well as an adjustment
1.5 Noise test drive of at least 20 km.

When assessing noises around the double clutch, perform Note:

a test drive to make sure that no noise is emanating from If you have any questions about diagnosis and repair,
surrounding components, such as the emission system, please contact our Technical Hotline on
heat shields, engine mountings, auxiliary equipment, +44 (0)1432 264264.
etc. The radio, air conditioning and ventilation must be
switched off during the noise investigation. A stethoscope
can also be used in the garage, for example, to locate the
source of the noise.

Double Clutch: Gearbox Side Double Clutch: Engine Side

7
2 Description and scope of delivery for the LuK RepSet 2CT

2 Description and scope of delivery for the LuK RepSet 2CT

The LuK RepSet 2CT (Twin Clutch Technology) includes Thanks to the LuK RepSet 2CT, Schaeffler Automotive
all the components required to replace the double clutch Aftermarket is able to offer a complete and practical
transmission. For a professional repair, it is recommended solution. The components included in the set are pre-
not only to replace the double clutch, but also all wear cision matched at the factory, eliminating problems
parts in the immediate vicinity. caused by fitting a mix of incompatible components.

8
1 10

2 7
3 5 6 9

Article no 602 0003 00

1 Central engagement system 6 Retaining element

2 3 screws for the central engagement system 7 Lip seal for the control rod
3 6 pressure plate screws 8 Release bearing
4 Double clutch 9 4 screws for the concentric slave cylinder
5 3 screws for the coupling flange 10 Concentric slave cylinder

8
 3 Description and scope of delivery for the LuK special tool

3 Description and scope of delivery for the LuK Special Tool

The tool kit (part no. 400 0471 10) contains all the tools reset and locked before installation of the transmission.
required for the professional repair of dry double clutches This step is performed using the reset tool supplied. The
in Alfa Romeos, Fiats, Jeeps and Suzukis (6-speed trans- tool can be adjusted to the respective DMF versions of the
mission C635 DDCT). The tool kit can be used without dry double clutch systems by Alfa Romeo and Fiat with
the basic tool kit. If the dual mass flywheel (DMF) is not just a few manual adjustments and can be used directly
replaced, the associated anti-backlash ring must be on the vehicle.

5 9

6
3
1
4
2 7 8 10

Article no 400 0471 10

1 2 plugs for differential openings

2 4 plugs for hydraulic openings Note:
3 Installation device for the control rod If you have any questions in relation to the special tool,
4 Hexagon socket set for the control rod please contact our Technical Hotline on
5 3 centering sleeves +44 (0)1432 264264.
6 3 threaded rods for centering sleeves
7 Installation device for the lip seal
8 Mounting sleeve for the lip seal
9 DMF reset tool
10 2 locking screws

9
10
 4 Remonal and installation of the double clutch

4 Removal and installation of the double clutch

4.1 Repair instructions

Valid for: • Before installing the double clutch, the transmission

Alfa Romeo, Fiat, Jeep and Suzuki (6-speed transmission input shafts must be cleaned thoroughly and checked
C 635 DDCT) for damage. The gearing must then be lubricated
with a suitable lubricant. The vehicle manufacturer’s
Using the LuK special tool: instructions are to be observed as a priority. If no
part no. 400 0471 10 instructions regarding the lubricant are provided by
the vehicle manufacturer, you can use a high-perfor-
Important Notes mance grease that is resistant to extreme tempera-
for a Proper Repair: tures and ageing (e.g. Castrol Olista Longtime 1 or 2)

• Repairs may be carried out only by specialist staff • Clutch system components must not be greased or
and using suitable garage equipment oiled (exceptions are clearly pointed out)

• Due to on-going technical developments during • After installing the clutch and transmission, a basic
volume production by the vehicle manufacturer, the adjustment must be carried out using a suitable
repair process and the special tools required are diagnostic system
subject to change
• Oily and/or dirty transmission parts must be cleaned
• Repairs must always be carried out using the latest before using new components
repair instructions and the appropriate special tool
• Cleanliness must be ensured throughout the entire
repair process
The latest data and information can be found at:
www.repxpert.com • After the repair, an adjustment test drive of at least
20 km is recommended
• If transmission oil or hydraulic oil leaks out during the
repair, the oil level must be checked and if necessary Important:
refilled once the transmission is installed Do not use DMF or double clutches that were
dropped!
• The dual mass flywheel (DMF) must be checked and
if necessary replaced when the double clutch is Do not clean components in a parts washing machine!
replaced. In the process, particular attention must be
paid to the internal gear teeth and the anti-backlash Do not remove the components
ring. The brochures entitled “The dry double clutch” (this can invalidate warranty claims)!
and “Dual mass flywheel” contain more information
about the DMF

• If the DMF is reused, the bracing ring must be reset

using a special tool (e.g. LuK part no. 400 0471 10)
before installing the transmission. In the case of a
new DMF, the anti-backlash ring is already reset

11
4 Removal and installation of the double clutch

4.2 Removal of the double clutch

• Remove the transmission, observing the vehicle

manufacturer’s instructions

• 
After removing the drive shafts, insert the plugs
(KL-0500-724) into the openings in the differential

• 
Place the gearbox in a position similar to the
installation position on the vehicle

• Remove the release bearing retaining element

Note:
In the process, the retaining element is destroyed
and must be replaced at the end of the repair (included
in the LuK RepSet 2CT).

• Loosen the release bearing nut

• Remove the release bearing

12
• Block the clutch (e.g. with a hexagon socket placed
between the double clutch and bell housing)

• Remove six pressure plate screws (hexagonal socket)

• Remove the blocking tool

Note:
If the Torx screws are unscrewed, the clutch
can no longer be used.

• Remove the clutch with the central plate from the

transmission input shaft

Important:
Do not drop the clutch hub on the
thread of the control rod!

• Remove the clutch disc from the transmission input

shaft

13
4 Removal and installation of the double clutch

• Turn the pressure plate until all three screws of the

flange bearing are accessible

• Remove the screws and the pressure plate

Important:
Do not drop the pressure plate on the thread of the
control rod!

• Check the radial clearance of the control rod

Note:
The fit is virtually free of clearance. If the clearance is
noticeable, the bush in the transmission input shaft
or the control rod is worn (see page 17).

• Remove the three screws of the central engagement

system

14
• Release the safety clips on the hydraulic pipe

• Remove the hydraulic pipe

Important:
Hydraulic fluid can escape with a low residual
pressure.

Wear gloves and safety glasses!

• Close the connection to the hydraulic unit with plug

KL-0500-728

• Release both tabs of the plastic catch

• Remove the hydraulic connection from the catch

• Remove the central engagement system

15
4 Removal and installation of the double clutch

• Remove the safety clip from the hydraulic pipe

• Pull the hydraulic pipe out of the concentric slave

cylinder

• Close the hydraulic pipe with plug KL-0500-728

• Disconnect the electrical connection from concentric

slave cylinder

• Remove four screws

• Remove the concentric slave cylinder with the control

rod

• Clean the sealing surface of the transmission housing

Note:
The oil deflector plate (1) is not part of the concentric
slave cylinder. If it disengages during removal, rein-
stall it in the gearbox. 1

• Clamp special tool KL-0500-722 in a vice

• Insert the concentric slave cylinder into the special

tool

• Remove the control rod with special tool KL-0500-726

16
• Check the control rod for wear in the area of the bear-
ings and the lip seal

Important:
If there is noticeable scoring or scratches in the area
of the guide, the control rod must be replaced along
with the bush in the transmission input shaft. This
work step can be combined with the replacement of
the lip seal (see below).

• Check the lip seals of the inner and outer transmis-

sion input shaft for leaks and, if necessary, replace
according to the instructions of the vehicle manufac-
turer

• Clean the gearing of both transmission input shafts

and check for damage

Remove the lip seal of the control rod

Note:
The seat of the lip seal must not be damaged during
removal as this can lead to a loss of oil.

• If impermissible radial clearance is detected during

the inspection of the control rod (see page 14), the
guide bush can be replaced during this work step
(note the specifications of the vehicle manufacturer)

17
4 Removal and installation of the double clutch

4.3 Installation of the double clutch

• Clean the thread of the control rod then apply

thread-locking compound

• New control rods are already provided with Loctite

• Insert the new concentric slave cylinder into special

tool KL-0500-722

• S
 crew the control rod into the concentric slave cylinder
using special tool KL-0500-726 and secure with 8 Nm

• Lay the clutch disc down on a clean surface. Make

sure not to touch the friction surfaces with your bare
hands; use gloves if necessary

• Coat the gearing of the clutch disc hub for the exter-
nal transmission input shaft with a little lubricant

Note:
Take the vehicle manufacturer’s specifications
into account when choosing the lubricant. Unless
specified, use a temperature and ageing-resistant,
high-performance grease (e.g. Castrol
Olista Longtime 2 or 3).

18
• Move the clutch disc back and forth several times in
three different angular positions to the transmission
input shaft over the full length of the splines

• Remove any excess lubricant from the outside of

the splines of the clutch disc and the transmission
input shaft

• Coat the splines of the inner input shaft with a thin

layer of grease

19
4 Removal and installation of the double clutch

• Install the concentric slave cylinder with the control

rod

• Make sure that the oil deflector plate is in the instal-

lation position

• Use a torque wrench to tighten the screws

to 10 Nm (±2 Nm)

• Remove the plug from the hydraulic pipe

• Connect the electrical and hydraulic connection to

the concentric slave cylinder

• Turn installation device KL-0500-723 on the thread of

the control rod and then wet with gear oil

• Guide the lip seal up to the end of the installation

device by hand, observing the installation direction

• Drive the lip seal to the specified end position with

special tool KL-0500-725

• Remove the installation device

Note:
The mounting depth of the lip seal is limited by a
transition in the transmission input shaft.

20
• Install the central engagement system

• Snap the hydraulic connection of the central engage-

ment system into place in the plastic catch

• Tighten three new screws evenly by hand; do not tilt

the concentric slave cylinder in the process

• Tighten the screws to 10 Nm (±2 Nm)

• First, attach the hydraulic pipe to the connection of

the central engagement system and lock it with a
safety clip

• Then remove the plug from the hydraulic unit and

connect the pipe

Note:
When installing the hydraulic pipe, make sure that
the connections are properly locked. Corrections on
installed transmissions are extremely difficult due
to space restrictions.

• Screw in threaded rods KL-0500-7271 as deep as

possible by hand into the bell housing

21
4 Removal and installation of the double clutch

• Position the holes of the pressure plate and the

flange above one another

• G
 uide the pressure plate with flange over the threaded
rods of the special tool

Important:
When installing the pressure plate, the rounded 2
recess of the flange (1) must be above the hydraulic
connection of the concentric slave cylinder (2) once
the hydraulic connection is assembled.

If the flange is incorrectly installed, the clutch and

engaging system will be damaged!
1

• Screw three centering sleeves KL-0500-727 evenly

onto the threaded rods by hand; do not tilt the flange
in the process

Note:
During this work step, the flange of the clutch is
pressed against preload of the central engagement
system in the seating of the transmission. In the
process, the increased force required for turning does
not yet indicate the final installation position. The
clutch only reaches its correct installation position
when all sleeves have come to a stop and the threaded
rods have the same length.

22
• Remove the first threaded rod with the sleeve,
replace with a new screw and tighten by hand

• Repeat the work step with the second and third

threaded rods

• Tighten the three screws with 25 Nm (±10 %)

• Check that the pressure plate can be turned by hand

evenly and silently

• Degrease the friction surface of the pressure plate

• Install the clutch disc

Note:
Note the installation position. The labels
“FLYWHEEL SIDE” or “LATO MOTORE”
must be facing the flywheel.

• Set the notch of the clutch to the “11 o’clock” position

23
4 Removal and installation of the double clutch

• Degrease the friction surface of the central plate

• Install clutch with central plate. Make sure that

the clutch hub does not interfere with or damage the
thread of the control rod

Important:
During installation, the notches of the clutches and
the central plate must be aligned!

• Hand tighten the screws

• Evenly and sequentially tighten to 25 Nm (±10 %)

(if necessary, block clutch in same way as removal)

• Screw on the release bearing until there is contact

with the diaphragm spring, then carefully continue
to turn until the thrust washer remains stationary

Important:
The nut should no longer be screwed in with the
thrust washer stationary, as this negatively affects
the measuring result of the following test.

24
• Place the steel ruler on both sides of the bell housing

• Measure the distance to the control rod and

note as measured value 1

Example: Measured value 1 = 21.0 mm

• Measure the distance to the plate of the release

bearing and note as measured value 2

Example: Measured value 2 = 35.0 mm

• Turn in the release bearing by 10.5 revolutions

25
4 Removal and installation of the double clutch

• Determine the distance to the control rod again

• Subtract the measured value from measured value 1

 Example: 21.0 mm – 10.5 mm = 10.5 mm

• The calculated value must equal 10.5 mm (±0.1 mm)

• If a value is outside the tolerance range, adjust

the release bearing nut until the required value is
reached

• Determine the distance to the plate of the release

bearing again

• Compare the determined measurement with meas-

ured value 2

Example: 35.0 mm (measured value 2)

35.0 mm (determined dimension)
deviation: 0.0 mm

• Deviations of more than ±2 mm are inadmissible and

indicate an error in installing the thrust bearing or in
its basic adjustment. To correct this, it is recommended
to repeat these work steps

• Install the new screw-locking device

26
 5 Instructions for the Dual Mass Flywheel (DMF)

5 Instructions for the Dual Mass Flywheel (DMF)

Important:
Before installing the transmission, the bracing ring
of a previously used DMF must be reset. If this is
not observed, the double clutch and the DMF will be
damaged!

• A function test on the DMF is not possible using ga-

rage equipment. If broken-off spring tabs or retaining
lugs are detected during the visual inspection, the
DMF must be replaced

DMF with a Reset Anti-backlash Ring

• The coil springs of the anti-backlash ring are

compressed and the spring tabs are at the stop

• The transmission can be mounted

Note:
New DMFs are always delivered with a reset
anti-backlash ring.

DMF with Triggered Anti-backlash Ring

• In the case of a previously used DMF, the coil springs

of the anti-backlash ring are relaxed and the spring
tabs are above the stop

• The transmission must not be mounted yet

• Before installing the transmission, the anti-backlash

ring must be reset using a special tool, e.g. KL-0500-721

27
6 DMF versions

6 DMF versions
Petrol and diesel engines can be equipped with two In the following repair procedure, each DMF is assigned
different DMF versions. The more current versions can a particular mounting position on the reset tool. It is
be identified by the anti-backlash ring with a flap for therefore advisable to use the images below to deter-
pivoting coil spring. In the case of older vehicles, this mine the DMF installed in the vehicle and to note down
design feature is missing. the version number.

DMF for Diesel Engines

Version 1: Anti-backlash ring with flap for pivoting coil Version 3: Anti-backlash ring without flap for pivoting coil
spring spring

DMF for Petrol Engines

Version 2: Anti-backlash ring with flap for pivoting coil Version 4: Anti-backlash ring without flap for pivoting coil
spring spring

28
 7 DMF reset tool KL-0500-721

7 DMF reset tool KL-0500-721

Design

Top of the reset tool

Driver

Locking screw

Angle pressure piece A

Return screw

Central knurled nut

Bottom of the reset tool

Angle pressure piece B

Large knurled nut of driver

Numbered threaded locking screw holes for the
various DMF versions

Eccentric

Bottom of the reset tool

Set screw

Clamping part

29
7 DMF reset tool KL-0500-721

Description

Vehicles with a dry double clutch are equipped with a If the mounted DMF is to be reused in an Alfa Romeo,
special design of the DMF. Instead of the friction surface, Fiat, Jeep and Suzuki dry double clutch system, the
a flange with internal gearing is used. The toothed gear anti-backlash ring must be reset before the transmission
of the double clutch meshes with this flange. Since the is installed.
two interlocking gear rings would otherwise produce
noise, a anti-backlash ring is attached to prevent noise. The reset tool KL-0500-721 can be used to reset the
This anti-backlash ring tensions the two sprockets so anti-backlash rings of all DMFs on the market up to now
that the tooth flanks have no clearance between them. for Alfa Romeo, Fiat, Jeep and Suzuki vehicles with a dry
double clutch. The DMF does not need to be removed.

Application Example

30
 8 Resetting the anti-backlash ring of the DMF

8 Resetting the anti-backlash ring of the DMF

Mounting position of the bottom of the reset tool for the
respective DMF versions.

Version 1

Diesel engine
Anti-backlash ring with flap for
pivoting coil spring

Version 2

Petrol engine
Anti-backlash ring with flap for
pivoting coil spring

31
8 Verspannring
Resetting the anti-backlash ring of the DMF
des ZMS zurückstellen

Version 3

Diesel engine
Anti-backlash ring without flap for
pivoting coil spring

Version 4

Petrol engine
Anti-backlash ring without flap for
pivoting coil spring

32
 Note:
The following instruction shows an example of reset-
ting version 1. All other versions can be reset accord-
ing to the same principle.

• Place the bottom of the reset tool centrally on the

DMF (observe the installation position of the respec-
tive version; see pages 31 and 32)

• Turn the eccentric clockwise using an Allen key until

both clamps fit in the teeth of the DMF

• Hold the eccentric with a small preload

• Check that the clamps are correctly seated in the

teeth

• Tighten both set screws

• Unscrew the reset screw with hexagonal socket as far

as possible

33
8 Resetting the anti-backlash ring of the DMF

• Turn driver (1) back to the stop

• Mount the top of the reset tool without locking

screws
1

• Secure central knurled nut by hand

Note:
In DMF versions 1 and 4, angle pressure piece B
of the top of the reset tool points toward the reset
screw. For versions 2 and 3, the top must be mounted
in such a way that the angle pressure piece A points 1
toward the reset screw.

• Align the drivers over the holes in the anti-backlash

ring and screw in evenly until the discs are on the
holes of the anti-backlash ring

• Tighten the large knurled nuts of the drivers by hand

• Evenly preload both drivers slightly

34
• Screw in the reset screw so that the anti-backlash
ring twists against the spring force

• 
Stop the procedure as soon as a small space is visible
between spring tab and stop

• Screw the locking screws into the threaded holes

labelled number 1 until there is contact with the
spring tabs

Note:
With DMF versions 2, 3 and 4, the locking screws
must be inserted into the correspondingly numbered
threaded bores.

35
8 Resetting the anti-backlash ring of the DMF

• Screw the locking screws in only until the spring tabs

are level with the stops

Important:
The spring tabs can break off if the locking screws are
screwed in too deep!

• Unscrew the reset screw so that both spring tabs

touch the stops

• Remove the special tool

• Install the transmission according to the vehicle

manufacturer’s instructions

36
 9 Installation and initial operation

9 Installation and initial operation

• Install the transmission according to the vehicle
manufacturer’s instructions

Important:
Engine and transmission must be brought together by
hand so that both flanges are touching all round. Only
then can the screws be fitted and secured with the
prescribed tightening torque.

If the transmission cannot be moved into the installa-

tion position, the connection between the clutch and
the DMF is tooth to tooth. In this case, the crankshaft
can be turned slightly in the engine rotation direction
until the gears engage. Bring the transmission as close as possible to the engine

If the transmission is forcibly pulled to the engine with Final Work
the help of the bolts, the double clutch and the DMF
will be damaged! • Perform a basic adjustment with a suitable diagnostic
tool
• Check the transmission oil level (specification accord- • Carry out a test drive of at least 20 km
ing to the instructions of the vehicle manufacturer) and • Check the hydraulic fluid level in the transmission
refill as necessary control again and if necessary add hydraulic fluid
• Check the hydraulic fluid level (specification according
to the instructions of the vehicle manufacturer) in the
transmission control and refill as necessary Note:
• Before the first start, it is advisable to use a suitable A complete adaptation of the clutch is performed
diagnostic tool to check that the gearing of the clutch within the first journey of 100 km. It is advisable to
is correctly seated in the gearing of the DMF drive through all driving profiles (in town, country and
on the motorway).
Workflow If there is still no satisfactory shifting comfort after
this test route, the clutch characteristic line must be
• Connect the diagnostic tool and switch on the reconfigured using a suitable diagnostic tool.
ignition
• Check the error memory. If error “P2949 – unwanted
opening of the clutch for odd gears” is stored, the
clutch is not properly seated in the teeth of the DMF –
do not start the engine until the error has been elimi-
nated
• Check the measured values. The indicators for the
signals “Clutch position for odd gears” and “Position
for closing clutch odd gears” must match. The value
should be 10 (± 1.0 mm). If a position value of under
7.8 mm is determined for the clutch for odd gears, this
means that the clutch is not correctly seated in the
teeth of the DMF. Do not start the engine until the error
is eliminated Basic adjustment with a suitable diagnostic tool

37
Notes

38
Notes

39
 999 6008 370/02.2021
© 2021 Schaeffler Automotive Aftermarket GmbH & Co. KG

www.repxpert.com