TS 590 User - Manual

INSTRUCTION MANUAL
HF/ 50 MHz ALL MODE TRANSCEIVER
TS-590S
Version: 1.05
NOTIFICATION
This equipment complies with the essential requirements of Directive 1999/5/EC.
The use of the warning symbol means the equipment is subject to restrictions of use
in certain countries.
This equipment requires a licence and is intended for use in the countries below.
AT BE DK FI FR DE GR IS
IE IT LI LU NL NO PT ES
SE CH GB CY CZ EE HU LV
LT MT PL SK SI BG RO
ISO3166
© B62‑2243‑20 (K, E)
09 08 07 06 05 04 03 02
THANK YOU NOTICE TO THE USER
Thank you for choosing this Kenwood TS-590S One or more of the following statements may be
transceiver. It has been developed by a team of applicable for this equipment.
engineers determined to continue the tradition of
FCC WARNING
excellence and innovation in Kenwood transceivers.
This equipment generates or uses radio frequency energy.
This transceiver features a Digital Signal Processing Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved
(DSP) unit to process IF and AF signals. By taking in the instruction manual. The user could lose the authority to
maximum advantage of DSP technology, the TS-590S operate this equipment if an unauthorized change or modification
transceiver gives you enhanced interference reduction is made.
capabilities and improves the quality of audio. You will
notice the differences when you fight QRM and QRN. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED
As you learn how to use this transceiver, you will also BY THE FCC
find that Kenwood is pursuing “user friendliness”. This equipment has been tested and found to comply with the
For example, each time you change the Menu No. in limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
Menu mode, you will see scrolling messages on the protection against harmful interference in a residential
display, telling you what you are selecting. installation.
This equipment generates, uses and can generate radio
Though user friendly, this transceiver is technically frequency energy and, if not installed and used in accordance
sophisticated and some features may be new to you. with the instructions, may cause harmful interference to radio
Consider this manual to be a personal tutorial from the communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this
designers. Allow the manual to guide you through the equipment does cause harmful interference to radio or television
learning process now, then act as a reference in the reception, which can be determined by turning the equipment off
coming years. and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
FEATURES receiver.
• All mode operation from HF to 50 MHz amateur • Connect the equipment to an outlet on a circuit different from
radio band that to which the receiver is connected.
• Consult the dealer for technical assistance.
• 500 Hz/ 2.7 kHz roofing filter
• Superior C/N response by the DDS largely
decreases the noise of the undesired signal. BEFORE STARTING
• IF DSP through the adoption of 32-bit floating point Amateur radio regulations vary from country to
DSP country. Confirm your local amateur radio regulations
• Digital Noise Blanker and requirements before operating the transceiver.
• PC interface via a Universal Serial Bus port Depending on the size and type of vehicle, the
(B-type) maximum transmission output power for the mobile
• Drive output and RX only antenna connector operation will vary. The maximum transmission output
power is usually specified by the car manufacturer
• Direct band keys
to avoid interference with other electric devices used
• Built-in Antenna Tuner for the HF/ 50 MHz band in the vehicle. Consult your car manufacturer and
• 100 W output power for SSB, CW, FSK, FM, and amateur radio equipment dealer for the requirements
25 W output power for AM. and installation.
MARKET CODES
K-type: The Americas
E-type: Europe
The market code is shown on the carton box.
Refer to the specifications {page 81} for information
on the available operating frequencies.
Information on Disposal of Old Electrical and Electronic Equipment

and Batteries (applicable for EU countries that have adopted
separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled
bin) cannot be disposed as household waste.
Old electrical and electronic equipment and batteries should
be recycled at a facility capable of handling these items and
their waste byproducts.
Contact your local authority for details in locating a recycle
facility nearest to you.
Proper recycling and waste disposal will help conserve
resources whilst preventing detrimental effects on our health
and the environment.
i
WRITING CONVENTIONS FOLLOWED SUPPLIED ACCESSORIES
The writing conventions described below have After carefully unpacking the transceiver, identify the
been followed to simplify instructions and avoid items listed in the table below. We recommend you
unnecessary repetition. keep the box and packing materials in case you need
to repack the transceiver in the future.
Instruction Action
Press [KEY]. Press and release KEY. Quantity
Accessory Comment
Press and release KEY on K-type E-type
Press Mic [KEY].
the microphone. Microphone 1 1
Press and hold KEY down DC power cable 1 1
Press and hold [KEY]. for a moment, then release Line filter (with
KEY. – 1
retaining band)
Press and hold KEY down 25 A; for DC
Hold [KEY]. until instructed to release Fuse 1 1
power cable
KEY.
4 A; for an
With the transceiver power Fuse external 1 1
OFF, press and hold KEY, antenna tuner
Press [KEY] + [ ].
then switch the transceiver
power ON by pressing [ ]. DIN plug 7-pin 1 1
DIN plug 13-pin 1 1
Screw set For bracket 1 1
Plastic spacer For bracket 4 4
English 1 1
French 1 1
Spanish – 1
Instruction Manual
German – 1
Italian – 1
Dutch – 1
Schematic
2 –
diagram
Warranty Card 1 1
ii
PRECAUTIONS • Locate the transceiver away from heat sources
such as a radiator, stove, amplifier or other devices
Please observe the following precautions to prevent that produce substantial amounts of heat.
fire, personal injury, and transceiver damage:
• Do not use volatile solvents such as alcohol, paint
• Connect the transceiver only to a power source thinner, gasoline, or benzene to clean the cabinet
as described in this manual or as marked on the of the transceiver. Use only a clean cloth with
transceiver itself. warm water or a mild detergent.
• Route all power cables safely. Ensure the power • Disconnect the input power cable from the power
cables can neither be stepped upon nor pinched source when the transceiver is not used for long
by items placed near or against the cables. periods of time.
Pay particular attention to locations near AC
receptacles, AC outlet strips, and points of entry to • Remove the transceiver’s enclosure only to do
the transceiver. accessory installations described in this manual or
accessory manuals. Follow provided instructions
• Take care not to drop objects or spill liquid into the carefully, to avoid electrical shocks. If unfamiliar
transceiver through enclosure openings. Metal with this type of work, seek assistance from an
objects, such as hairpins or needles, inserted into experienced individual, or have a professional
the transceiver may contact voltages resulting in technician do the task.
serious electrical shocks. Never permit children to
insert any objects into the transceiver. • Enlist the services of qualified personnel in the
following cases:
• Do not attempt to defeat methods used for
grounding and electrical polarization in the a) The power supply or plug is damaged.
transceiver, particularly involving the power input b) Objects have fallen into or liquid has spilled into
cable. the transceiver.
• Adequately ground all outdoor antennas for this c) The transceiver has been exposed to rain.
transceiver using approved methods. Grounding d) The transceiver is operating abnormally or
helps protect against voltage surges caused by performance has seriously degraded.
lightning. It also reduces the chance of a build-up
of static charge. e) The transceiver has been dropped or the
enclosure damaged.
EXAMPLE OF ANTENNA GROUNDING
• Do not attempt to perform any kind of configuration
or menu setup while driving.
ANTENNA
LEAD IN • Do not wear headphones while driving.
GROUND WIRE
• Install the transceiver in a safe and convenient
CLAMP
ANTENNA position inside your vehicle so as not to subject
DISCHARGE UNIT yourself to danger while driving. Consult your car
dealer for the transceiver installation to ensure
GROUNDING
CONDUCTORS safety.
GROUND CLAMPS • HF/ 50 MHz mobile antennas are larger and
ELECTRIC SERVICE heavier than VHF/ UHF antennas. Therefore, use
EQUIPMENT POWER SERVICE
GROUNDING ELECTRODE a strong and rigid mount to safely and securely
SYSTEM install the HF/ 50 MHz mobile antenna.
• Minimum recommended distance for an outdoor

antenna from power lines is one and one-half
times the vertical height of the associated antenna
support structure. This distance allows adequate
clearance from the power lines if the support
structure fails for any reason.
• Locate the transceiver so as not to interfere with its
ventilation. Do not place books or other equipment
on the transceiver that may impede the free
movement of air. Allow a minimum of 10 cm
(4 inches) between the rear of the transceiver and
the wall or operating desk shelf.
• Do not use the transceiver near water or sources
of moisture. For example, avoid use near a
bathtub, sink, swimming pool, or in a damp
basement or attic.
• The presence of an unusual odor or smoke is often
a sign of trouble. Immediately turn the power OFF
and remove the power cable. Contact a Kenwood
service station or your dealer for advice.
iii
CONTENTS
THANK YOU ............................................................ i TX SIDETONE/ RX PITCH FREQUENCY ........ 23
FEATURES .............................................................. i CARRIER LEVEL .................................................. 23
NOTICE TO THE USER ........................................... i POWER ON MESSAGE ........................................ 23
BEFORE STARTING ............................................... i
MARKET CODES ..................................................... i CHAPTER 6 ENHANCED COMMUNICATIONS
WRITING CONVENTIONS FOLLOWED .................ii SPLIT-FREQUENCY OPERATION....................... 24
SUPPLIED ACCESSORIES .....................................ii TF-SET (TRANSMISSION FREQUENCY SET) 24
PRECAUTIONS ......................................................iii FM REPEATER OPERATION ............................... 25
CONTENTS .............................................................iv TRANSMITTING A TONE ................................. 25
Activating the Tone Function ........................ 26
CHAPTER 1 INSTALLATION Selecting a Tone Frequency ........................ 26
ANTENNA CONNECTION ...................................... 1 TONE FREQUENCY ID SCAN ......................... 26
GROUND CONNECTION ....................................... 1 FM CTCSS OPERATION ...................................... 26
LIGHTNING PROTECTION .................................... 1 CTCSS FREQUENCY ID SCAN ....................... 27
DC POWER SUPPLY CONNECTION .................... 1 CROSS TONE ....................................................... 27
UTILIZING THE BAIL .............................................. 2
REPLACING FUSES .............................................. 2 CHAPTER 7 COMMUNICATING AIDS
ACCESSORY CONNECTIONS .............................. 2 RECEPTION ......................................................... 28
FRONT PANEL ................................................... 2 SELECTING YOUR FREQUENCY ................... 28
Headphones (PHONES) ................................ 2 Direct Frequency Entry................................. 28
Microphone (MIC)........................................... 2 Frequency Entry History ............................... 28
REAR PANEL...................................................... 2 Using the MHz key ....................................... 28
External Speaker (EXT.SP)............................ 2 Quick QSY.................................................... 28
Keys for CW (PADDLE and KEY) .................. 2 Fine Tuning .................................................. 29
Tuning Control Adjustment Rate .................. 29
CHAPTER 2 GETTING ACQUAINTED Equalizing VFO Frequencies (A=B) ............. 29
FRONT PANEL ....................................................... 4 RIT (RECEIVE INCREMENTAL TUNING) ............ 29
LCD DISPLAY ......................................................... 7 AGC (AUTOMATIC GAIN CONTROL).............. 29
REAR PANEL .......................................................... 9 AGC Time Constant Adjustment .................. 29
MICROPHONE ........................................................ 9 TRANSMISSION ................................................... 30
VOX (VOICE-OPERATED TRANSMISSION) ... 30
CHAPTER 3 OPERATING BASICS Microphone Input Level ................................ 30
SWITCHING POWER ON/ OFF ............................ 10 Delay Time ................................................... 30
ADJUSTING THE VOLUME .................................. 10 Anti-VOX Adjustment ................................... 30
AF (AUDIO FREQUENCY) GAIN...................... 10 Data VOX ..................................................... 30
RF (RADIO FREQUENCY) GAIN ..................... 10 Data VOX Delay Time .................................. 31
SELECTING VFO A OR VFO B ............................ 10 USB/ ACC2 VOX Gain ................................. 31
SELECTING A BAND ............................................ 11 SPEECH PROCESSOR.................................... 31
SELECTING A MODE ........................................... 11 peech Processor Effect ................................ 31
ADJUSTING THE SQUELCH................................ 12 XIT (TRANSMIT INCREMENTAL TUNING) ..... 31
TUNING A FREQUENCY ...................................... 12 CUSTOMIZING TRANSMISSION SIGNAL
MULTI-FUNCTION METER .................................. 12 CHARACTERISTICS ........................................ 32
TRANSMITTING ................................................... 13 TX Filter Bandwidth (SSB/ AM) .................... 32
SELECTING TRANSMISSION POWER ........... 13 TX Filter Bandwidth (LSB-DATA/ USB-DATA) . 32
MICROPHONE GAIN ........................................ 13 TX Equalizer (SSB/ AM/ FM)........................ 32
TRANSMIT INHIBIT .......................................... 32
CHAPTER 4 MENU SETUP
BUSY LOCKOUT .............................................. 32
WHAT IS A MENU? .............................................. 14 CHANGING FREQUENCY WHILE
MENU A/ MENU B ................................................ 14 TRANSMITTING ............................................... 32
MENU ACCESS .................................................... 14 CW BREAK-IN ...................................................... 33
QUICK MENU ....................................................... 14 USING SEMI BREAK-IN OR FULL BREAK-IN ..... 33
PROGRAMMING THE QUICK MENU .............. 14 ELECTRONIC KEYER .......................................... 33
USING THE QUICK MENU ............................... 14 ELECTRONIC KEYER MODE .......................... 33
MENU CONFIGURATION ..................................... 15 CHANGING KEYING SPEED ........................... 33
CHARACTER ENTRY ........................................... 20 Invalid Break-In Operation............................ 33
RISE TIME OF CW ........................................... 34
CHAPTER 5 BASIC COMMUNICATIONS
AUTO WEIGHTING........................................... 34
SSB TRANSMISSION ........................................... 21 Reverse Keying Weight Ratio ...................... 34
FM TRANSMISSION ............................................. 21 BUG KEY FUNCTION ....................................... 34
AM TRANSMISSION ............................................. 22 CW MESSAGE MEMORY ................................ 34
NARROW BANDWIDTH FOR FM......................... 22 Storing CW Messages.................................. 34
CW TRANSMISSION ............................................ 22 Checking CW Messages without
AUTO ZERO-BEAT ........................................... 23 Transmitting.................................................. 35
iv
CONTENTS
Transmitting CW Messages ......................... 35 PROGRAM SCAN PARTIALLY SLOWED ........ 47

Changing the Inter-message Interval Time ... 35 SCAN HOLD ..................................................... 48
Changing the CW Sidetone Volume............. 35 MEMORY SCAN ................................................... 48
Insert Keying ................................................ 35 SCAN RESUME ................................................ 48
FREQUENCY CORRECTION FOR CW ........... 35 ALL-CHANNEL SCAN....................................... 48
AUTO CW TX IN SSB MODE ........................... 36 GROUP SCAN .................................................. 49
MIC UP/ DWN KEY PADDLE MODE ................ 36 Memory Group ............................................. 49
SWAP DOT AND DASH PADDLE POSITIONS 36 Scan Group Select ....................................... 49
Performing Group Scan................................ 49
CHAPTER 8 DATA COMMUNICATIONS QUICK MEMORY SCAN ....................................... 49
RADIO TELETYPE (RTTY) ................................... 37
PHASE-SHIFT KEYING 31 BAUD (PSK31).......... 37 CHAPTER 12 OPERATOR CONVENIENCES
ANTENNAS ........................................................... 50
CHAPTER 9 REJECTING INTERFERENCE ANT 1/ ANT 2 .................................................... 50
DSP FILTERS ....................................................... 38 RX ANT ............................................................. 50
CHANGING THE DSP FILTER BANDWIDTH .. 38 DRV ................................................................... 50
SSB/ FM/ AM Mode...................................... 38 APO (Auto Power OFF) ......................................... 50
CW/ FSK Mode ............................................ 38 AUTOMATIC ANTENNA TUNER .......................... 50
Data Mode .................................................... 38 PRESETTING ................................................... 51
IF Filter A and B ........................................... 38 AUTO MODE ......................................................... 51
AUTO NOTCH FILTER (SSB) ............................... 39 BEEP FUNCTION ................................................. 52
AUTO NOTCH TRACKING SPEED .................. 39 DISPLAY ............................................................... 53
MANUAL NOTCH FILTER (SSB/ CW/ FSK) ......... 39 BRIGHTNESS ................................................... 53
Notch Filter Bandwidth ................................. 39 BACKLIGHT COLOR ........................................ 53
BEAT CANCEL (SSB/ AM) ............................... 39 PANEL KEY DOUBLE FUNCTION RESPONSE
NOISE REDUCTION (ALL MODES) ................. 39 TIME ...................................................................... 53
Setting the NR1 Level Adjustment ............... 40 LINEAR AMPLIFIER CONTROL ........................... 53
Setting the NR2 Time Constant.................... 40 LOCK FUNCTIONS ............................................... 53
NOISE BLANKER ................................................. 40 FREQUENCY LOCK FUNCTION ..................... 53
PRE-AMPLIFIER ................................................... 40 PROGRAMMABLE FUNCTION KEYS.................. 54
ATTENUATOR ...................................................... 40 TRANSCEIVER FRONT PANEL....................... 54
CW REVERSE (RECEPTION) .............................. 40 MICROPHONE KEYS ....................................... 54
DSP RX EQUALIZER ............................................ 55
CHAPTER 10 MEMORY FEATURES
Equalizing Receiving Audio .......................... 55
MEMORY CHANNELS .......................................... 41 RX MONITOR ................................................... 55
STORING DATA IN MEMORY.......................... 41 TIME-OUT TIMER ................................................. 55
Simplex Channels ........................................ 41 TRANSVERTER .................................................... 55
Split-Frequency Channels ............................ 41 FREQUENCY DISPLAY.................................... 55
MEMORY RECALL AND SCROLL ................... 42 TRANSMISSION OUTPUT POWER................. 56
Memory Recall ............................................. 42 TX MONITOR ........................................................ 56
Memory Scroll .............................................. 42 TX POWER ........................................................... 56
Temporary Frequency Changes................... 42 TX TUNE ............................................................... 56
MEMORY TRANSFER ...................................... 42 QUICK DATA TRANSFER .................................... 56
Memory ➡ VFO Transfer.............................. 42 SETTING UP ..................................................... 56
Channel ➡ Channel Transfer ....................... 42 Equipment Needed....................................... 56
STORING FREQUENCY RANGES .................. 43 Connections ................................................. 56
Confirming Start/ End Frequencies .............. 44 USING QUICK TRANSFER .............................. 57
Programmable VFO ..................................... 44 Transferring Data ......................................... 57
MEMORY CHANNEL LOCKOUT...................... 44 Receiving Data ............................................. 57
ERASING MEMORY CHANNELS .................... 44 COMPUTER CONTROL ....................................... 57
MEMORY CHANNEL NAME............................. 44 SETTING UP ..................................................... 57
QUICK MEMORY .................................................. 44 Equipment Needed....................................... 57
NUMBER OF QUICK MEMORY CHANNELS ... 45 Connections ................................................. 57
STORING INTO QUICK MEMORY ................... 45 COMMUNICATION PARAMETERS ................. 57
RECALLING QUICK MEMORY CHANNELS .... 45 EXTERNAL AUDIO SETTINGS ........................ 58
TEMPORARY FREQUENCY CHANGES ......... 45 Selecting a Data Transmission Line ............. 58
QUICK MEMORY ➡ VFO TRANSFER ............. 45 Audio Level Settings..................................... 58
ERASING QUICK MEMORY CHANNELS ........ 45 TERMINAL ........................................................ 58
CHAPTER 11 SCAN CONTROLLING THE TS-590S FROM A PC .... 58
REMOTELY CONTROLLING THE TS-590S ON
NORMAL SCAN .................................................... 46 THE NETWORK ................................................ 58
VFO SCAN ........................................................ 46 OPTIONAL VGS-1 VOICE GUIDE & STORAGE
PROGRAM SCAN ............................................. 46 UNIT ...................................................................... 58
v
CONTENTS
RECORDING MESSAGES ............................... 58 CHAPTER 16 OPTIONAL ACCESSORIES

MESSAGE PLAYBACK..................................... 59 OPTIONAL ACCESSORIES ................................. 80
Checking Messages ..................................... 59
Sending Messages ....................................... 59 CHAPTER 17 SPECIFICATIONS
Erasing a Recorded Message ...................... 59 SPECIFICATIONS ................................................ 81
Changing Inter-message Interval Time ........ 59
Changing Message Playback Volume.......... 60
CONSTANT RECORDING................................ 60
VOICE GUIDE ................................................... 60
Voice Guide Announcement Volume .......... 62
Voice Guide Announcement Speed ............ 62
Voice Guide Announcement Language ....... 62
EMERGENCY CALL (K TYPE ONLY) .................. 62
CROSSBAND REPEATER .................................. 63
OPERATION ..................................................... 63
DX PACKETCLUSTER TUNE............................... 63
SKY COMMAND SYSTEM II................................. 64
SKY COMMAND SYSTEM II DIAGRAM........... 64
PREPARATION................................................. 64
CHAPTER 13 CONNECTING PERIPHERAL EQUIPMENT
TERMINAL DESCRIPTIONS ................................ 65
COM CONNECTOR .......................................... 65
ACC2 CONNECTOR......................................... 65
REMOTE CONNECTOR ................................... 66
EXT.AT CONNECTOR (FOR AT-300) .............. 66
MIC CONNECTOR............................................ 66
COMPUTER .......................................................... 67
COMPATIBLE TRANSCEIVER ............................. 67
RTTY OPERATION ............................................... 68
HF/ 50 MHz LINEAR AMPLIFIER ......................... 68
ANTENNA TUNER ................................................ 69
TNC AND MCP ..................................................... 69
DX PACKETCLUSTER TUNE............................... 70
CROSSBAND REPEATER ................................... 70
CHAPTER 14 INSTALLING OPTIONS
REMOVING THE BOTTOM CASE........................ 71
VGS-1 VOICE GUIDE & STORAGE UNIT ............ 71
SO-3 TCXO ........................................................... 72
REFERENCE FREQUENCY CALIBRATION ....... 72
MB-430 MOBILE BRACKET ................................. 73
PRECAUTIONS ................................................ 73
CHAPTER 15 TROUBLESHOOTING
GENERAL INFORMATION ................................... 74
SERVICE........................................................... 74
SERVICE NOTE................................................ 74
CLEANING ........................................................ 74
TROUBLESHOOTING .......................................... 75
MICROPROCESSOR RESET............................... 78
INITIAL SETTINGS ........................................... 78
VFO RESET ...................................................... 78
FULL RESET..................................................... 78
OPERATION NOTICES ........................................ 79
DC POWER SUPPLY ....................................... 79
INTERNAL COOLING FAN ............................... 79
INTERNAL BEATS ............................................ 79
AGC................................................................... 79
60m BAND OPERATION (K-TYPE/ USA ONLY) ..79
vi
INSTALLATION
ANTENNA CONNECTION LIGHTNING PROTECTION
An antenna system consists of an antenna, feed Even in areas where lightning storms are less
line, and ground. The transceiver can give excellent common, there is always a chance that a storm will
results if the antenna system and its installation are occur each year. Consider carefully how to protect
given careful attention. Use a properly adjusted 50 Ω your equipment and home from lightning. The
antenna of good quality, a high-quality 50 Ω coaxial installation of a lightning arrestor is a start, but there
cable, and top-quality connectors. All connections is more that you can do. For example, terminate
must be clean and tight. your antenna system transmission lines at an entry
panel that you install outside your home. Ground this
After making the connections, match the impedance
entry panel to a good outside ground, then connect
of the coaxial cable and antenna so that the SWR is
the appropriate feed lines between the entry panel
1.5:1 or less. High SWR will cause the transmit output
and your transceiver. When a lightning storm occurs,
to drop and may lead to radio frequency interference
disconnecting the feed lines from your transceiver will
with consumer products such as stereo receivers
ensure additional protection.
and televisions. You may even cause interference
with your own transceiver. Reports that your signal is
distorted could indicate that your antenna system is
not efficiently radiating your transceiver’s power. DC POWER SUPPLY CONNECTION
Connect your primary HF/ 50 MHz antenna feed In order to use this transceiver, you need a separate
line to ANT 1 on the rear of the transceiver. If you 13.8 V DC power supply that must be purchased
are using two HF/ 50 MHz antennas, connect the separately. Do not directly connect the transceiver
secondary antenna to ANT 2. Refer to page 9 for the to an AC outlet. Use the supplied DC power cable to
location of the antenna connectors. connect the transceiver to a regulated power supply.
Do not substitute a cable with smaller gauge wires.
The LF band is outputed only from the DRV terminal. The current capacity of the power supply must be
Note: 20.5 A peak or more.
◆ Transmitting without connecting an antenna or other
matched load may damage the transceiver. Always connect First, connect the DC power cable to the regulated DC
the antenna to the transceiver before transmitting. power supply; the red lead to the positive terminal and
◆ All fixed stations should be equipped with a lightning arrester the black lead to the negative terminal. Next, connect
to reduce the risk of fire, electric shock, and transceiver the DC power cable to the transceiver’s DC power
damage.
connector.
◆ The transceiver’s protection circuit will activate when
the SWR is greater than 1.5:1; however, do not rely on • Press the connectors firmly until the locking tab
protection to compensate for a poorly functioning antenna clicks.
system.
• Attach the line filter to the DC cable as shown
below (E-type only).
GROUND CONNECTION Note:
◆ Before connecting the DC power supply to the transceiver,
At a minimum, a good DC ground is required to be sure to switch OFF the DC power supply and transceiver.
prevent such dangers as electric shock. For superior ◆ Do not plug the DC power supply into an AC outlet until you
communications, a good RF ground is required make all connections.
against which the antenna system can operate. Both
of these conditions can be met by providing a good
earth ground for your station. Bury one or more
ground rods or a large copper plate under the ground,
then connect this to the transceiver GND terminal.
Use heavy gauge wire or a copper strap, cut as short
as possible, for this connection. Do not use a gas
pipe, an electrical conduit, or a plastic water pipe as a
ground.
Fuse (25 A)
E-type only
Black (−) Red (+)

DC Power supply
TS-590S (20.5 A or more)
1
1 INSTALLATION
UTILIZING THE BAIL ACCESSORY CONNECTIONS

This transceiver is equipped with a bail so that you
can angle the transceiver. The bail is located on the FRONT PANEL
bottom of the transceiver. Pull the bail forward to the
limit as shown. ■ Headphones (PHONES)
Connect monaural or stereo headphones with a
4 to 32 Ω (normal 8 Ω) impedance. This jack
accepts a 6.3 mm (1/4") diameter, 2-conductor
(mono) or 3-conductor (stereo) plug. After
connecting the headphones, you will hear no
sound from the internal (or optional external)
Speaker/Microphone (MIC).
Note: Using a high impedance headphone set causes the
volume to be louder.
■ Microphone (MIC)
Connect a microphone with a 250 to 600 Ω
impedance. Fully insert the connector, then
screw the retaining ring clockwise until secure.
Compatible microphones include the MC-43S,
MC-47, MC-52DM, MC-60A, MC-80, MC-85, and
MC-90.
Note: Do not use the MC-44, MC-44DM, MC-45, MC-45E,
REPLACING FUSES MC-45DM, MC-45DME, or MC-53DM microphones.
The following fuses are used in the TS-590S
transceiver. If a fuse blows, determine the cause
then correct the problem. Only after the problem has REAR PANEL
been resolved, replace the blown fuse with a new
one with the specified ratings. If newly installed fuses ■ External Speaker (EXT.SP)
continue to blow, disconnect the power plug and On the rear panel of the transceiver, there is an
contact a Kenwood service center or your dealer for external speaker jack. If an external speaker is
assistance. connected to EXP.SP, the transceiver internal
speaker will mute. Use only external speakers with
Fuse Location Fuse Current Rating an impedance of 4 to 8 Ω (8 Ω nominal). This jack
4A accepts only 3.5 mm (1/8") diameter, 2-conductor
TS-590S Transceiver (for external (mono) plugs.
antenna tuner)
Supplied DC power cable 25 A
Do not connect headphones to this jack. The high audio
output of this jack could damage your hearing.
■ Keys for CW (PADDLE and KEY)

Fuse (4 A)
For CW operation while using the internal
electronic keyer, connect a keyer paddle to the
PADDLE jack.
For CW operation without using the internal
electronic keyer, connect a straight key,
semi-automatic key (bug), electronic keyer,
or the CW keyed output from a Multimode
Fuse (25 A)
Communications Processor (MCP) to the KEY
jack.
The PADDLE and KEY jacks mate with a 6.3 mm
Fuse (25 A) (1/4") 3-conductor plug and a 3.5 mm (1/8")
2-conductor plug, respectively. External electronic
keyers or MCPs must use positive keying to be
compatible with this transceiver. Use a shielded
cable between the key and the transceiver.
Note: Due to the functionality of the internal electronic

keyer, you may find it unnecessary to connect both a paddle
and another type of keyer unless you want to use a
PC-based keyer for CW. Read the “ELECTRONIC KEYER”
section {page 33} to become familiar with the internal keyer.
2
1 INSTALLATION
Headphones
Front Panel
2 GND (STBY)
MIC :
> GND (MIC)
PTT @
B NC
DOWN .
= 8 V (10 mA max)
UP ;
MIC connector (Front view)
External speaker
Microphone
Rear Panel
• Paddle
• Straight key
• Bug key
• Electronic keyer
• PC keyer output
3
GETTING ACQUAINTED
FRONT PANEL
A G
C D E F
B H
—— A —— —— C ——
[ ] [METER (DRV)]
Press and hold to switch the transceiver power ON Press to switch the meter type {page 12}. Press and
and OFF {page 10}. hold to turn the Drive Out function ON or OFF {page 50}.
[PF A] [PF B]
You can assign a function to this Programmable You can assign a function to this Programmable
Function key {page 54}. Function key {page 54}.
[ATT (RX ANT)] [MIC (CAR)]
Press to turn the receiver attenuator ON or OFF Press to adjust the microphone gain {page 13}. While
{page 40}. Press and hold to enable or disable the the Speech Processor function is ON, press to adjust
RX-ANT terminal {page 50}. the Speech Processor output level {page 31}. Press
[PRE (ANT 1/2)] and hold to adjust the carrier level {page 23}.
Press to turn the pre-amplifier ON or OFF {page 40}. [PWR (TX MONI)]
Press and hold to select either ANT 1 or ANT 2 Press to adjust the transmission output power
{page 50}. {pages 13, 565}. Press and hold to turn the
[VOX (LEV)] transmission signal monitor function ON or OFF
In voice mode, press to turn the VOX (Voice-Operated {page 56}.
Transmit) function ON or OFF {page 30}. In CW [KEY (DELAY)]
mode, press to turn the Break-in function ON or OFF Press to adjust the internal electronic keyer speed
{page 33}. Press and hold to adjust the microphone {page 33}. Press and hold to adjust the VOX delay
input gain for VOX operation. time for voice mode {page 30} or Break-in time (Full
[PROC (LEV)] Break-in/ Semi Break-in time) for CW mode.
Press to turn the Speech Processor ON or OFF [GENE]
{page 31}. Press and hold to adjust the Speech Press to select the general coverage band memory
Processor input level. {page 11}.
[SEND] [1.8 (1)]
Press to turn transmission ON or OFF. Press to select the 1.8 MHz band memory {page 11}
[AT (TUNE)] or enter keypad number 1.
Press to turn the internal antenna tuner ON or [3.5 (2)]
OFF {page 50}. Press and hold to start tuning the Press to select the 3.5 MHz band memory {page 11}
automatic antenna tuner. or enter keypad number 2.
—— B —— [7 (3)]
Press to select the 7 MHz band memory {page 11} or
PHONES jack enter keypad number 3.
Mate with a 6.3 mm (1/4") diameter, 2-conductor
(mono) or 3-conductor (stereo) plug for connecting a [10 (4)]
set of headphones {page 2}. Press to select the 10 MHz band memory {page 11} or
enter keypad number 4.
MIC connector
Connect a microphone to this connector {page 2}. [14 (5)]
[18 (6)]
4
2 GETTING ACQUAINTED
[21 (7)] [NB (LEV)]

Press to select the 21 MHz band memory {page 11} or Press to cycle through Noise Blanker 1, Noise Blanker
enter keypad number 7. 2, and OFF. Press and hold to adjust the Noise
[24 (8)] Blanker level {page 40}.
Press to select the 24 MHz band memory {page 11} or [NR (LEV)]
enter keypad number 8. Press to cycle through the DSP Noise Reduction
[28 (9)] types: NR1, NR2, or OFF {page 39}. When the
Press to select the 28 MHz band memory {page 11} or Noise Reduction function is turned ON, press and
enter keypad number 9. hold to change the parameters of the Noise Reduction
function {page 40}.
[50 (0)]
Press to select the 50 MHz band memory {page 11} or [BC (A.NOTCH)]
enter keypad number 0. Press to select the DSP Beat Cancel function, BC1
(Beat Cancel 1), BC2 (Beat Cancel 2) or OFF
[CLR] {page 39}. Press and hold to toggle the Auto
Press to exit from, abort, or reset various functions. Notch Filter ON and OFF {page 39}.
Press and hold to clear a memory channel {page 44}.
[NOTCH (WIDE)]
[ENT] Press to toggle the IF Notch Filter ON or OFF
Press to enter your desired frequency using the {page 39}. Press and hold to set up the IF Notch
10-key keypad {page 28}. bandwidth {page 39}.
—— D —— [SPLIT]
Press to enter split-frequency operation, allowing
[LSB/USB] you to use different transmission and reception
Press to select LSB or USB mode {page 11}. frequencies {page 24}.
[CW/FSK (REV)] [TF-SET]
Press to select CW or FSK mode {page 11}. Press During split-frequency operation, press to monitor or
and hold to select a sideband (CW/ CW-R or FSK/ change your transmit frequency {page 24}.
FSK-R).
[A/B (A=B)]
[FM/AM (FM-N)] Press to select either VFO A or VFO B {page 24}.
Press to select FM or AM mode {page 11}. Press and Press and hold to duplicate the data in the current
hold to select Narrow FM mode. VFO to the other VFO {page 25}. While in Menu
[DATA] mode, press to select Menu A or Menu B. While in
Press to select a Data mode (LSB/ LSB-DATA, USB/ Program Memory Channel mode, press to recall the
USB-DATA, or FM/ FM-DATA) {page 11}. start or end frequency.
[FINE (F.LOCK)] [M/V]
Press to activate the Fine tuning function to allow Press to toggle between Memory and VFO modes.
more precise tuning {page 29}. Press and hold to [M.IN]
activate the Frequency Lock function {page 53}. Press to enter Memory Scroll mode and to store data
to a Memory channel {page 41}.
—— E ——
[M>V]
Central (Tuning) control Press to transfer the current Memory Channel
Turn to select the desired frequency {page 12}. Use contents to the VFO.
the convenient finger-tip cavity for continuous tuning.
Slide the lever underneath the Tuning control to the [Q-M.IN]
left or right to adjust the torque level of the control. Press to store data to the Quick Memory {page 44}.
Left makes the control light and right makes it heavy. [Q-MR]
Press to recall data from the Quick Memory {page 45},
while in VFO mode. Press to enter Memory Name
light Edit mode, while in Memory Channel mode {page 44}.
heavy
[MHz]
TX-RX LED Press to turn the MHz Up/ Down function ON or OFF.
Lights red while transmitting and green when the The MHz digit increases or decreases when you turn
squelch opens while receiving. the MULTI/CH control. In Menu mode, press to turn
the Quick Menu ON or OFF {page 14}.
—— F ——
[SCAN (SG.SEL)]
[IF FIL]
Press to start or stop the Scan function {page 46}.
Press to toggle between IF Filter A and IF Filter B
Press and hold to select a Scan group {page 49}.
{page 38}. You can adjust the filter bandwidth using
the LO/WIDTH and HI/SHIFT controls. Press and [MENU]
hold [IF FIL] to momentarily display each setting value Press to enter Menu mode {page 14}.
of the current DSP filter DSP filter bandwidth {page
38}.
5
A G
C D E F
B H
[CH1 (REC)] RIT/ XIT control

Press to play back a CW {page 34} or voice message When the RIT/ XIT function is ON, turn to adjust
(requires VGS-1 option) {page 58}. Press and hold the offset frequency. The RIT/ XIT offset frequency
to record a CW {page 34} or voice message (requires appears on the sub-display {pages 29, 31}. While
VGS-1 option) {page 59}. scanning, turn to adjust the scan speed.
[CH2 (REC)] —— H ——
Press to play back a CW {page 34} or voice message
SQL control
(requires VGS-1 option) {page 59}. Press and hold
Turn to select the desired squelch level {page 12}.
to record a CW {page 34} or voice message (requires
VGS-1 option) {page 59}. NOTCH control
Turn to select the desired Notch frequency {page 39}.
[CH3 (REC)]
Press to play back a CW {page 34} or voice message MULTI/CH control
(requires VGS-1 option) {page 59}. Press and hold In VFO mode, rotate to step the operating frequency
to record a CW {page 34} or voice message (requires up or down {page 28}. In Memory Channel mode,
VGS-1 option) {page 59}. rotate to select a Memory Channel {page 41}.
Also, used for selecting Menu numbers when
[RX/4 (REC)]
accessing the Menu mode {page 14} and for various
Press to play back a CW {page 34} or voice message
configurations. The MULTI/CH LED lights when the
(requires VGS-1 option) {page 59}, or the constantly
MULTI/CH control is not being used to adjust the step
recorded signal (requires VGS-1 option) {page 60}.
frequency.
Press and hold to activate the constant recorder
(requires VGS-1 option) {page 60}. HI/SHIFT control
Rotate to adjust the DSP filter bandwidth (high-cut) or
—— G —— to adjust the DSP filter bandwidth (filter band shift)
[AGC/T (SEL)] {page 38}.
Press to toggle the fast or slow response time for LO/WIDTH control
the Automatic Gain Control (AGC) {page 29}. In Rotate to adjust the DSP filter bandwidth (high-cut or
FM mode, press to cycle through the Tone settings: shift) {page 38}.
Tone, CTCSS, CTCSSx, or OFF {page 26}. When
Tone is activated in FM mode, press and hold to AF control
select a Tone frequency {page 26}. When CTCSS Turn to adjust the AF gain level {page 10}.
is activated in FM mode, press and hold to select a RF control
CTCSS frequency {page 27}. Turn to adjust the RF gain level {page 10}.
[CW T. (AGC OFF)]
Press to start CW auto tuning {page 23}. Press and
hold to turn AGC OFF {page 29}.
[RIT]
Press to turn the RIT (Receive Incremental Tuning)
function ON or OFF {page 29}.
[XIT]
Press to turn the XIT (Transmit Incremental Tuning)
function ON or OFF {page 31}.
[CL]
Press to clear the RIT/ XIT frequency to zero
{pages 29, 31}.
6
LCD DISPLAY
A B C D
E F
—— A ——
Appears when the Noise Blanker 1 or 2 is ON
{page 40}.
While receiving, the meter serves as an S-meter to

measure and display the received signal strength. “ ” (fast) or “ ” (slow) appears when the
While transmitting, it serves as a power meter plus an Automatic Gain Control function is ON. “ ”
ALC meter, an SWR meter, or a Speech Processor appears when the AGC is OFF {page 29}.
compression meter. The Peak Hold function holds
each reading for approximately half a second. While Appears when IF filter A is selected {page 38}.
adjusting the IF filter bandwidth, the meter displays an
adjustment state.
Appears when IF filter B is selected {page 38}.
—— B ——
—— D ——
Appears when the Auto Mode function is ON and
while in Auto Mode frequency setup {page 51}. “ ” appears when manual notch is set to Normal.
“ ” appears when Manual Notch is set to Wide.
“ ” appears when Auto Notch is selected {page
Displays the operating mode (USB, LSB, FM, AM, 39}.
CW, CWR, FSK, or FSR) {page 11}.
Appears when the Fine Tuning function is ON {page
Appears while in Menu mode {page 14}. 29}.
Appears while in Memory Scroll mode {page 42}. Appears when the MHz Step function is ON {page
28}. Also appears when the Quick Menu function is
ON {page 14}.
Appears while in Memory Channel mode or Memory
Scroll mode {page 42}.
“ ” or “ ” appears, depending on whether
DSP Noise Reduction 1 or Noise Reduction 2 is
In normal operating mode and various configuration selected {page 39}.
modes, it displays the Memory Channel number,
Quick Memory number, and entry log number. In
Menu mode, it displays the Menu No. “ ” appears when the RX Equalizer function is ON
{page 55}. “ ” appears when the TX Equalizer
—— C —— function is ON {page 32}.
Appears while in Data mode {page 38}. “ ” or “ ” appears, when you select the DSP
Beat Cancel 1 or Beat Cancel 2 {page 39}.
Appears while in narrow FM mode {page 11}.
“ ” appears when the Tone function is ON {page 25},
Appears when the receiver pre-amplifier is ON {page and blinks during Tone scan. “ ” appears when the
40}. CTCSS (Continuous Tone Coded Squelch System)
function is ON, and blinks during CTCSS scan {page
26}. “ ” appears when the Cross Tone function is
Appears when the receiver’s attenuator is ON {page ON {page 27}.
40}.
7
A B C D
E F
—— F ——
Appears when the VOX (Voice Operated
Transmission) function is ON or the Break-in function
is ON for CW mode {page 30}.
(Main DIsplay)
In normal operating mode and various configuration
Appears when the Frequency Lock function is ON modes, it displays the transceiver operating
{page 53}. frequency. In Menu mode, it displays the various
menus, and in Adjustment mode, it displays the
adjustment values.
Appears when the Speech Processor function is ON
{page 31}.
(Sub-display)
When recalling a memory channel, it displays
Appears when the constant recording function is ON
the Memory Channel name (if one has been
{page 60}.
programmed). During split frequency operation,
it displays the frequency. When the following
Reserved for future updates. indications occur simultaneously, information is
displayed in the following order: RIT/XIT frequency,
Split frequency, Memory Name. In Menu mode, it
Appears when the selected Menu No. is in the
displays a menu title. In other modes, it displays the
Quick Menu list {page 14}. It also appears when the
configuration parameters.
transceiver is scanning the frequencies between the
slow down frequency points {page 47}.
Appears when the split-frequency operation is ON
{page 24}.
Appears when Receive Incremental Tuning function is
ON {page 29}.
“ ” appears while VFO A is selected. “ ”
appears while transmitting on a split channel in VFO
Appears when Transmit Incremental Tuning function
A {page 10}. “ ” appears while Menu A is being
is ON {page 31}.
accessed in Menu mode {page 14}.
—— E ——
“ ” appears while VFO B is selected. “ ” appears
Appears when the RX ANT terminal is enabled {page while transmitting on a split channel in VFO B {page
50}. 10}. “ ” appears while Menu B is being accessed in
Menu mode {page 14}.
Either “ ” or “ ” appears, depending on

which antenna connector is selected {page 50}. “ ” appears while a simplex memory channel
is selected. “ ” appears while a split memory
channel is selected {page 41}.
“ ” appears while the internal antenna tuner
{page 61} is in-line for operation. “ ” appears while
receiving when the internal antenna tuner is in-line for
operation. “ ” and “ ” blink while tuning is in progress
{page 50}.
Appears when the DRV terminal is enabled {page 50}.
8
REAR PANEL
ANT 1 and ANT 2 connectors DRV connector

Connect your primary HF/ 50 MHz antenna to ANT 1 Connect a drive device to this RCA connector {page
connector. If you are using 2 antennas for the HF/ 50}.
50 MHz band, connect the secondary antenna to the
RX ANT connector
ANT 2 connector {page 1}.
Connect a separate receive-only antenna for HF low
GND post bands to this RCA connector {page 50}.
Connect a heavy gauge wire or copper strap between
the ground post and the nearest earth ground {page 1}.
AT connector MICROPHONE
Mates with the connector from the cable supplied with
the AT-300 external antenna tuner {pages 66, 68}.
Refer to the instruction manual supplied with the tuner
for more information.
DC 13.8 V connector
Connect a regulated 13.8 V DC power source to this
connector {page 1}. Use the DC cable supplied with
the transceiver.
COM connector
Mates with a DB-9 female connector for connecting a
computer or compatible transceiver {pages 57, 65}.
Also used with the Quick Data Transfer function {page
57} and DX PacketCluster Tune function {page 63}.
(USB) connector
Mates with a USB connector for connecting a
computer via one of its USB ports {pages 57, 67}.
EXT.SP 8Ω jack PTT (Push-to-Talk) switch
Mate with a 3.5 mm (1/8"), 2-conductor (mono) plug The transceiver is placed in Transmission mode when
for connecting an external speaker {page 2}. this non-locking switch is held down. Releasing the
switch returns the transceiver to Reception mode.
ACC 2 connector
Mates with a 13-pin male DIN connector for / Mic [UP]/ [DWN]
connecting various accessory equipment, such as Use these keys to step the VFO frequency, Memory
an external TNC/ MCP or a RTTY terminal Channels, or Menu selections up and down.
{page 65}. Press and hold these keys to continuously change the
settings.
REMOTE connector
You can also change the operational function of these
Mates with a 7-pin male DIN connector for connecting
keys {page 54}
an HF/ 50 MHz linear amplifier {page 65, 68}.
KEY and PADDLE jacks
The KEY jack mates with a 3.5 mm (1/8") 2-conductor
plug for connecting an external key for CW operation.
The PADDLE jack mates with a 6.3 mm (1/4")
3-conductor plug for connecting a keyer paddle to
the internal electronic keyer. Refer to “Keys for CW
(PADDLE and KEY)” {page 2} before using these jacks.
9
OPERATING BASICS
SWITCHING POWER ON/ OFF RF (RADIO FREQUENCY) GAIN
1 Switch the DC power supply ON. The RF gain is normally configured to the maximum
level regardless of the operating modes. The
2 Press [ ] to switch the transceiver ON. transceiver has been configured to the maximum
• If you hold the power switch for more than level at the factory. However, you may decrease the
approximately 2 seconds, the transceiver will RF gain slightly when you have trouble hearing the
switch back OFF. desired signal due to excessive atmospheric noise or
• Upon power up, “HELLO” appears on the main interference from other stations.
display, followed by the current frequency and First, take note of the peak S-meter reading of
other indicators. the desired signal. Then, turn the RF control
counterclockwise until the S-meter reads the peak
value that you noted.
3 To switch the transceiver OFF, press [ ] again.

4 Switch the DC power supply OFF.
• Signals that are weaker than this level will be
• You may skip step 3. After switching the attenuated and reception of the station will become
transceiver ON, you can switch it OFF or ON easier.
using only the power switch of the DC power
supply. The transceiver remembers the power Depending on the type and gain of your antenna and
switch position when the DC power source is the condition of the band, adjust the RF gain. When
switched OFF. using FM mode, always adjust the RF gain to the
maximum level.
ADJUSTING THE VOLUME SELECTING VFO A OR VFO B

AF (AUDIO FREQUENCY) GAIN Two VFOs are available for controlling the frequency
on the transceiver. Each VFO (VFO A and VFO B)
Turn the AF control clockwise to increase the audio works independently so that a different frequency and
level and counterclockwise to decrease it. mode can be selected. For example, when SPLIT
operation is activated, VFO A is used for reception
and VFO B is used for transmission. The opposite
combination is also possible.
Press [A/B (A=B)] to toggle between VFO A and B.
Note: The position of the AF control does not affect the volume
of beeps caused by pressing keys nor the CW TX sidetone. The
audio level for Digital mode operation is also independent of the
AF control setting.
10
3 OPERATING BASICS
SELECTING A BAND SELECTING A MODE

Press [1.8 (1)] ~ [50 (0)] or [GENE] to select your Press one of the following keys to select your desired
desired band. mode set: [LSB/USB], [CW/FSK (REV)], or [FM/AM
(FM-N)].
[LSB/USB]
Press to select LSB or USB mode. Press again to
toggle between LSB and USB mode.
While in LSB mode, press [DATA] to toggle between
LSB and LSB-DATA mode. Likewise, while in USB
mode press [DATA] to toggle between USB and USB-
DATA mode.
Additionally, while in LSB-DATA or USB-DATA mode,
• Press each key to cycle through the 3 default
you can press [LSB/USB] to toggle between LSB-
settings as shown in the table below.
DATA and USB-DATA mode.
• Each setting can be modified with your personal
preference for frequency and mode. After [CW/FSK (REV)]
modifying the setting, pressing the key again will Press to select CW or FSK mode. Press again to
save that setting. toggle between CW and FSK mode.
While in CW mode, press and hold [CW/FSK (REV)]
Default Setting (MHz)/ to toggle between CW and CW-R mode. Likewise,
Frequency while in FSK mode press and hold [CW/FSK (REV] to
Key Type Range Mode
toggle between FSK and FSK-R mode.
(MHz) 1 2 3 Additionally, while in CW-R or FSK-R mode, you can
1.8/ 1.82/ 1.84/ press [CW/FSK (REV)] to toggle between CW-R and
K FSK-R mode.
CW CW CW
[1.8 (1)] 1.62 ~ 2
1.83/ 1.84/ 1.81/ [FM/AM (FM-N)]
E Press to select FM or AM mode. Press again to
CW CW CW
toggle between FM and AM mode.
3.8/ While in FM mode, press and hold [FM/AM (FM-N)]
K
3.5/ 3.7/ LSB to toggle between FM and FM-NAR mode, or press
[3.5 (2)] 3~4
LSB LSB 3.79/ [DATA] to toggle between FM and FM-DATA mode.
E Additionally, while in FM-NAR mode, press [DATA] to
LSB
toggle between FM-NAR and FM-NAR-DATA mode
7.1/ 7.2/ and while in FM-DATA mode, press and hold [FM/AM
K
7.0/ LSB LSB (FM-N)] to toggle between FM-DATA and FM-NAR-
[7 (3)] 6.5 ~ 7.5
LSB 7.05/ 7.1/ DATA mode.
E
LSB LSB
10.1/ 10.12/ 10.14/
[10 (4)] All 10 ~ 10.5
CW CW CW
14.0/ 14.1/ 14.2/
[14 (5)] All 13.5 ~ 14.5
USB USB USB
18.068/ 18.11/ 18.15/
[18 (6)] All 18 ~ 19
USB USB USB
21.0/ 21.15/ 21.3/ Access Menu No. 23 then press [M.IN] to select “on”
[21 (7)] All 20.5 ~ 21.5
USB USB USB to turn the Auto Mode selection ON. When it is ON,
“ ” appears. As a default, if you change the
24.89/ 24.93/ 24.95/
[24 (8)] All 24 ~ 25 frequency above or below 9.5 MHz, the transceiver
USB USB USB
automatically switches modes; LSB for frequencies
28/ 28.3/ 29/ under 9.5 MHz and USB for frequencies 9.5 MHz and
[28 (9)] All 27.5 ~ 30
USB USB FM over. You can further add the frequency borders to the
Auto Mode selection {page 51}.
50.125/
K
50/ USB 51/
[50 (0)] 50 ~ 54
USB 50.15/ FM
E
USB
5.3305/
K
0.1357/ USB 5.4035/
[GENE] 0.03 ~ 60
CW 5.2585/ USB
E
USB
11
3 OPERATING BASICS
ADJUSTING THE SQUELCH MULTI-FUNCTION METER

The purpose of the Squelch is to mute the speaker The multi-function meter measures the parameters
when no signals are present. With the squelch level in the table below. The S-meter and FILTER scales
correctly set, you will hear sound only while actually appears when the transceiver is in receive mode, and
receiving signals. The higher the selected squelch the PWR meter appears when it is in transmit mode.
level, the stronger the signals must be to receive. The Each press of [METER (DRV)] cycles between the
appropriate squelch level depends on the ambient RF ALC, COMP, and SWR meters. Peak readings for the
noise conditions. S-meter, ALC, SWR, COMP, and PWR functions are
Turn the SQL control when there are no signals held momentarily.
present to select the squelch level at which the
background noise is just eliminated; the green TX-RX
LED will turn off. Many ham operators prefer leaving
the SQL control fully counterclockwise unless
operating on a full-carrier mode such as FM. The
squelch level for the transceiver is preset at the
factory to approximately the 9 o’clock position for FM
and 11 o’clock for SSB and AM.
ALC
COMP
TUNING A FREQUENCY
Turn the Tuning control clockwise or press Mic [UP
to increase the frequency. Turn the Tuning control
counterclockwise or press Mic [DWN] to decrease the
SWR
frequency.
Meter Name Parameters Measured

S Strength of received signals
PWR Transmission output power
ALC Automatic level control status
SWR Antenna system standing wave ratio
You may prefer directly entering a frequency using Speech compression level when
the numeric keypad if the desired frequency is far COMP using the Speech Processor
from the current frequency. Press [ENT], then press {page 31}
the numeric keys as necessary. For details, refer to FILTER IF filter width {page 38}
“Direct Frequency Entry” {page 28}.
Note:
◆ The COMP meter functions only when the Speech
Processor is ON for SSB, FM, or AM mode.
◆ Peak Hold readings cannot be deactivated.
◆ The S-meter responds differently in FM mode, compared to
other modes. This is not a malfunction.
12
3 OPERATING BASICS
TRANSMITTING MICROPHONE GAIN

For voice communications, press and hold Mic [PTT] The microphone gain must be adjusted when SSB
and speak into the microphone in your normal voice. or AM mode is selected without using the speech
When you finish speaking, release Mic [PTT] to processor {pages 21, 22}.
receive. 1 Press [MIC (CAR)].
To transmit CW, press [VOX (REV)] to turn the Break-
in function ON. “ ” appears. Close the key or
keyer paddle. Connect a key or keyer paddle {page
2}, then select CW using [CW/FSK (REV)].
For a detailed explanation on transmitting, refer to
“BASIC COMMUNICATIONS”, beginning on page 21.
SELECTING TRANSMISSION POWER

• The current microphone gain level appears.
It is wise to select a lower transmission power if
The range is from 0 to 100 with a default of 50.
communication is still reliable. This lowers the risk of
interfering with others on the band. When operating
from battery power, selecting a lower transmission
power allows you more operating time before
recharging is necessary. This transceiver allows
you to change the transmission power even while 2 Press and hold Mic [PTT].
transmitting. • The TX-RX LED lights red.
1 Press [PWR (TX MONI)]. 3 SSB: While speaking into the microphone, adjust
the MULTI/CH control so that the ALC meter
reflects your voice level but does not exceed the
ALC limit.
AM: While speaking into the microphone, adjust
the MULTI/CH control so that the power meter
slightly reflects your voice level.
FM: Access Menu No. 47 and select “1” (Normal),
“2” (Medium), or “3” (High) for the microphone gain
• The current transmission power appears. if necessary {page 21}.
2 Turn the MULTI/CH control counterclockwise to

reduce the power or clockwise to increase the
power.
4 Release Mic [PTT] to receive.

• The TX-RX LED lights green or turns off,
depending on the SQL control setting.
5 Press [MIC (CAR)] or [CLR] to exit the Microphone
gain adjustment.
Note: When using the MC-90 microphone in FM mode, select
3 Press [PWR (TX MONI)] or [CLR] to complete the “3” (High) for the microphone gain. The microphone sensitivity
is low in FM mode. This may cause insufficient modulation. For
setting. other microphones, select either “1” (Normal) or “2” (Medium).
Note: You can access Menu No. 48, and select “on” to change
the step size from 5 W to 1 W {page 56}.
13
MENU SETUP
WHAT IS A MENU? QUICK MENU
Many functions on this transceiver are selected or Because the number of functions this transceiver
configured via a software-controlled Menu, rather than provides is extraordinary, there are numerous items
through the physical controls of the transceiver. Once in each Menu. If you find accessing desired Menu
familiar with the Menu system, you will appreciate the Nos. to be too time consuming, use the Quick Menu to
versatility it offers. You can customize the various create your own customized, abbreviated Menu. You
timings, settings, and programming functions on this can then add those Menu Nos. which you frequently
transceiver to meet your needs without using many use, to the Quick Menu. Copying Menu Nos. to the
controls and switches. Quick Menu has no effect on the Menu.
PROGRAMMING THE QUICK MENU

MENU A/ MENU B 1 Press [MENU].
This transceiver has 2 menus: Menu A and Menu B. 2 Press [Q-M.IN]/ [Q-MR] or turn the MULTI/CH
These menus contain identical functions and can be control to select the desired Menu No.
configured independently. The transceiver, therefore,
allows you to switch between 2 different environments 3 Press [FINE (F.LOCK)].
quickly and easily. For example, you can configure • “ ” appears, indicating that the Menu item has
Menu A for DXing and contesting while Menu B is been added to the Quick Menu.
for relaxed local ragchewing. By switching from
Menu A to Menu B, you can instantly change the
Menu configuration and key assignment to suit your
current operating style. Or, 2 operators may share
a single transceiver by dedicating one Menu to each • To remove the item from the Quick Menu, press
operator. Both operators can always enjoy their own [FINE (F.LOCK)] again. “ ” disappears.
configuration.
4 Press [MENU] to exit Menu mode.
MENU ACCESS USING THE QUICK MENU

1 Press [MENU]. 1 Press [MENU].
• The Menu No. and setting appear on the 2 Press [MHz].
display, and the explanation of the menu • “ ” appears.
appears on the sub-display.
3 Press [Q-M.IN]/ [Q-MR] or turn the MULTI/CH

2 Press [A/B (A=B)] to select Menu A or B. control to select the desired Quick Menu No.
• “ ” or “ ” appears, indicating which Menu is 4 Press [M.IN]/ [SCAN (SG.SEL)], or Mic [UP]/
selected. [DWN] to change the current setting for the
3 Press [Q-M.IN]/ [Q-MR] or turn the MULTI/CH selected Menu No.
control to select the desired Menu No. • When the Menu is registered to the Quick Menu
• Each time you change the Menu No., list, “ ” appears.
a different scrolling message appears on the 5 Press [MENU] to exit Quick Menu mode.
sub-display, describing the Menu No.
Note: If the Quick Menu has not been programmed, Press [Q-
4 Press [M.IN]/ [SCAN (SG.SEL)], or Mic [UP]/ M.IN]/[Q-MR] or turning the MULTI/CH control in step 2 causes
[DWN] to select a parameter. “CHECK” to be output in Morse code.
14
4 MENU SETUP
MENU CONFIGURATION
Description Settings** Ref.
Category No.
Display* Default** Page
Display brightness
OFF/ 1 ~ 6
00 Off, 1: minimum, 6: maximum 53
DISPLAY BRIGHTNESS 4
Display backlight color
1/ 2
Operator 01 1: amber, 2: green 53
Interface
BACKLIGHT COLOR 1
Panel key response for double function
1/ 2/ 3
1: 0.2 second, 2: 0.5 second, 3: 1 second
02 53
PANEL KEY RESPONSE FOR DOUBLE
2
FUNCTIONS
Beep output level
OFF/ 1 ~ 9 (1 step)
03 OFF, 1: minimum, 9: maximum 52
BEEP VOLUME 4
Sidetone volume
OFF/ 1 ~ 9 (1 step)
Volume 04 OFF, 1: minimum, 9: maximum 23, 35
SIDETONE VOLUME 4
VGS-1 message playback volume
OFF/ 1 ~ 9 (1 step)
MESSAGE PLAYBACK VOLUME 4
VGS-1 announcement volume
OFF/ 1~ 7 (1 step)
VOICE GUIDE VOLUME 4
VGS-1 announcement speed
0 ~ 4 (1 step)
07 0: slow, 4: fast 62
Voice Guide VOICE GUIDE SPEED 1
VGS-1 announcement language
EN/ JP
08 EN: English, JP: Japanese 61
VOICE GUIDE LANGUAGE EN
VGS-1 auto announcement OFF/ ON
09 60
AUTO ANNOUNCEMENT ON
MHz step 0.1/ 0.5/ 1 [MHz]
10 28
MHZ STEP 1
Tuning control adjustment rate 250/ 500/ 1000 [Hz]
11 TUNING CONTROL CHANGE RATE PER 29
1000
REVOLUTION
Rounds off VFO frequencies changed by using the
OFF/ ON
MULTI/CH control
12 28
Tuning FREQUENCY ROUNDING OFF WHEN USING
ON
MULTI/CH CONTROL
9 kHz frequency step size for the MULTI/CH
OFF/ ON
control in AM mode on the AM broadcast band
13 28
MULTI/CH CONTROL 9KHZ STEP CHANGE IN K type: OFF
AM BROADCAST BAND E type: ON
Frequency step size for the MULTI/CH control in
0.5/ 1/ 2.5/ 5/ 10 [kHz]
14 SSB/ CW/ FSK mode 28
MULTI/CH CONTROL 5
15
4 MENU SETUP

Category No.
Frequency step size for the MULTI/CH control in 5/ 6.25/ 10/ 12.5/ 15/ 20/
15 AM mode 25/ 30/ 50/ 100 [kHz] 28
Tuning AM MULTI/CH CONTROL 5
(continued) Frequency step size for the MULTI/CH control in 5/ 6.25/ 10/ 12.5/ 15/ 20/
16 FM mode 25/ 30/ 50/ 100 [kHz] 28
FM MULTI/CH CONTROL 10
Number of quick memory channels 3/ 5/ 10 [ch]
17 45
NUMBER OF QUICK MEMORY CHANNELS 5
Memory Channel
Tunable memory recall frequencies OFF/ ON
18 42
TUNABLE MEMORY RECALL FREQUENCIES OFF
Program scan partially slowed OFF/ ON
19 47
PROGRAM SCAN PARTIALLY SLOWED ON
100/ 200/ 300/ 400/ 500
Slow down frequency range for the program scan
20 [Hz] 47
Scan PROGRAM SLOW-SCAN RANGE 300
Program scan hold OFF/ ON
21 47
PROGRAM SCAN HOLD OFF
Scan resume method TO/ CO
22 48
SCAN RESUME METHOD TO
Auto mode operation ON/ OFF
Auto Mode 23 51
AUTO MODE OPERATION OFF
Auto notch tracking speed 0 ~ 4 (1 step)
24 39
AUTO NOTCH TRACKING SPEED 2
10/ 100/ 200/ 300/ 400/
TX filter for SSB/AM low cut
25 500 [Hz] 32
TX FILTER FOR SSB/AM LOW CUT 300
2500/ 2600/ 2700/ 2800/
TX filter for SSB/AM high cut
26 2900/ 3000 [Hz] 32
TX FILTER FOR SSB/AM HIGH CUT 2700
DSP Function
10/ 100/ 200/ 300/ 400/
TX filter for SSB-DATA low cut
27 500 [Hz] 32
TX FILTER FOR SSB-DATA LOW CUT 300
2500/ 2600/ 2700/ 2800/
TX filter for SSB-DATA high cut
28 2900/ 3000 [Hz] 32
TX FILTER FOR SSB-DATA HIGH CUT 2700
Speech processor effect SOFT/ HARD
29 31
SPEECH PROCESSOR EFFECT HARD
DSP TX equalizer
oFF: Off, Hb1: High boost1, Hb2: High boost2, FP: OFF/ HB1/ HB2/ FP/ BB1/
30 Formant pass, bb1: Bass boost1, BB2/ C/ U 32
bb2: Bass boost2, c: Conventional,
U: User (Reserved for ARCP software)
DSP TX EQUALIZER OFF
Equalizer
DSP RX equalizer
oFF: Off, Hb1: High boost1, Hb2: High boost2, FP: OFF/ HB1/ HB2/ FP/ BB1/
31 Formant pass, bb1 Bass boost1, BB2/ FLAT/ U 55
bb2: Bass boost2, FLAT: Flat
U: User (Reserved for ARCP software)
DSP RX EQUALIZER OFF
16
4 MENU SETUP

Category No.
Electronic keyer mode A/ B
32 33
ELECTRONIC KEYER MODE B
Keying priority over playback OFF/ ON
33 34
KEYING PRIORITY OVER PLAYBACK OFF
CW RX pitch/ TX sidetone frequency 300 ~ 1000 (50 [Hz] step)
34 23
CW RX PITCH/TX SIDETONE FREQUENCY 800
CW rise time 1/ 2/ 4/ 6 [ms]
35 33
CW RISE TIME 6
AUTO/ 2.5 ~ 4.0
CW keying dot, dash weight ratio
36 (0.1 step) 33
CW WEIGHTING AUTO
Reverse CW keying auto weight ratio OFF/ ON
37 33
REVERSED CW WEIGHTING OFF
CW Bug key function OFF/ ON

38 34
BUG KEY FUNCTION OFF
Reversed dot and dash keying OFF/ ON
39 36
REVERSED DOT AND DASH KEYING OFF
MIC UP/DWN key paddle function
PF/ PA
40 PF: PF key PA: Paddle 36
MIC UP/DWN KEY FUNCTION PF
Auto CW TX when keying in SSB OFF/ ON
41 36
AUTO CW TX WHEN KEYING IN SSB OFF
Frequency correction for changing SSB to CW OFF/ ON
42 FREQUENCY CORRECTION FOR SSB-TO-CW 36
OFF
CHANGE
No Break-in operation while adjusting keying
OFF/ ON
43 speed 33
NO BK-IN WHILE ADJUSTING KEYING SPEED OFF
FSK shift 170/ 200/ 425/ 850 [Hz]
44 37
FSK SHIFT 170
FSK keying polarity OFF/ ON
FSK 45 37
REVERSED FSK KEY-DOWN POLARITY OFF
FSK tone frequency 1275/ 2125 [Hz]
46 37
FSK TONE FREQUENCY 2125
MIC gain for FM
1~3
FM 47 1: Low, 2: Mid, 3: Hi 21
FM MIC GAIN 1
Fine transmission power tuning OFF/ ON
48 56
FINE TRANSMIT POWER CHANGE STEPS OFF
TX Control OFF/ 3/ 5/ 10/ 20/ 30
Time-out timer
49 (min) 55
TIME-OUT TIMER OFF
Xverter/ power down of Xverter OFF/ 1/ 2
Transverter 50 55
XVERTER/ POWER DOWN OF XVERTER OFF
17
4 MENU SETUP

Category No.
TX hold when AT completes the tuning OFF/ ON
51 50
ANTENNA TUNER TX HOLD OFF
Antenna Tuner
In-line AT while receiving OFF/ ON
52 50
ANTENNA TUNER FOR RECEPTION OFF
Linear amplifier control relay for HF band OFF/ 1/ 2/ 3
53 53
HF LINEAR AMPLIFIER CONTROL RELAY OFF
Linear Amp
Linear amplifier control relay for 50 MHz band OFF/ 1/ 2/ 3
54 53
50MHZ LINEAR AMPLIFIER CONTROL RELAY OFF
Constant recording OFF/ ON
55 60
CONSTANT RECORDING ON
Repeat the playback OFF/ ON
Message 56 36, 59
PLAYBACK REPEAT OFF
Interval time for repeating the playback 0 ~ 60 [s] (1 step)
57 36, 59
PLAYBACK INTERVAL TIME 10
Split frequency transfer in master/ slave operation OFF/ ON
58 TRANSFER SPLIT FREQUENCY DATA TO 57
OFF
ANOTHER TRANSCEIVER
Split/ Transfer
Permit to write the transferred Split frequencies to
OFF/ ON
59 the target VFOs 57
COPY SPLIT FREQUENCY DATA TO VFO OFF
TX inhibit OFF/ ON
TX Inhibit 60 32
TX INHIBIT OFF
4800/ 9600/ 19200/
COM port communication speed***
61 38400/ 57600/ 115200 57
PC COM PORT BAUDRATE 9600 (bps)
(Communication) 4800/ 9600/ 19200/
USB port communication speed***
62 38400/ 57600/ 115200 57
USB PORT BAUDRATE 115200 (bps)
Audio input line selection for data communications ACC2/ USB
63 AUDIO INPUT LINE SELECT FOR DATA 58
ACC2
COMMUNICATIONS
Audio level of USB input for data communications 0 ~ 9 (1 step)
64 AUDIO LEVEL OF USB INPUT FOR DATA 58
4
COMMUNICATIONS
Audio level of USB output for data communications 0 ~ 9 (1 step)
65 AUDIO LEVEL OF USB OUTPUT FOR DATA 58
4
COMMUNICATIONS
External Audio
(Input/ Output) Audio level of ACC2 input for data communications 0 ~ 9 (1 step)
66 AUDIO LEVEL OF ACC2 INPUT FOR DATA 58
4
COMMUNICATIONS
AUDIO level of ACC2 output for data
0 ~ 9 (1 step)
communications
67 58
AUDIO LEVEL OF ACC2 OUTPUT FOR DATA
4
COMMUNICATIONS
Mixing beep tones for ACC2/USB audio output OFF/ ON
68 MIXING BEEP TONES FOR ACC2/USB AUDIO 58
OFF
OUTPUT
18
4 MENU SETUP

Category No.
Data VOX OFF/ ON
69 30
VOX OPERATION WITH DATA INPUT OFF
Data VOX delay time 0 ~ 100 (5 step)
70 30
DATA VOX DELAY TIME 50
Data VOX gain for the USB audio input 0 ~ 9 (1 step)
71 31
USB VOX GAIN 4
Data VOX gain for the ACC2 terminal 0 ~ 9 (1 step)
72 31
ACC2 VOX GAIN 4
External PKS polarity OFF/ ON
73 63
Accessory REVERSED PKS POLARITY OFF
Control
Busy lockout (TX) OFF/ ON
74 32
BUSY FREQUENCY TRANSMISSION LOCKOUT OFF
CTCSS mute control 1/ 2
75 58
CTCSS MUTE CONTROL 1
PSQ control signal logic LO/ OPEN
76 58
PSQ OUTPUT LOGIC LO
OFF/ BSY/ SQL/ SND/
PSQ source output condition
77 BSY-SND/ SQL-SND 58
PSQ SOURCE SQL
APO (Auto Power Off) function OFF/ 60/ 120/ 180 [min]
Timer 78 50
AUTO POWER OFF OFF
0 ~ 87, 100 ~ 134,
Front panel PF A key assignment
79 200 ~ 208, OFF 54
FRONT PANEL PF A KEY ASSIGNMENT 200 [VOICE1]
0 ~ 87, 100 ~ 134,
Front panel PF B key assignment
80 200 ~ 208, OFF 54
FRONT PANEL PF B KEY ASSIGNMENT 201 [VOICE2]
0 ~ 87, 100 ~ 134,
Microphone PF 1 key assignment
81 200 ~ 208, OFF 54
MIC PF 1 KEY ASSIGNMENT 130 [A/B]
0 ~ 87, 100 ~ 134,
82 200 ~ 208, OFF 54
MIC PF 2 KEYASSIGNMENT 128 [SPLIT]
PF Keys
0 ~ 87, 100 ~ 134,
83 200 ~ 208, OFF 54
MIC PF 3 KEY ASSIGNMENT 132 [M>V]
0 ~ 87, 100 ~ 134,
84 200 ~ 208, OFF 54
MIC PF 4 KEY ASSIGNMENT 203 [MONITOR]
0 ~ 87, 100 ~ 134,
Microphone DWN key assignment
85 200 ~ 208, OFF 54
MIC DOWN KEY ASSIGNMENT 206 [DOWN]
0 ~ 87, 100 ~ 134,
Microphone UP key assignment
86 200 ~ 208, OFF 54
MIC UP KEY ASSIGNMENT 207 [UP]
Power on message HELLO/ EDIT
Message 87 23
POWER ON MESSAGE KENWOOD
* The bolded lettering of the display message is what appears on the display while paused.
** Settings and default values may be modified.
*** After changing this setting via the menu, turn the power OFF and then back ON to implement the change. 19
4 MENU SETUP
CHARACTER ENTRY
When character entry is required, a cursor will appear
on the display.
1 Move the cursor to the left or right by pressing [Q-
M.IN] or [Q-MR].
2 Turn the MULTI/CH control or press [M.IN]/

[SCAN (SG.SEL)] to select your desired character.
• You can delete the selected character by
pressing [CL].
3 Repeat steps 1 and 2 to enter the remaining
characters.
4 Press [MENU] to set the entry and to exit character
entry mode.
• Press [CLR] at any time to cancel character
entry mode and return to the Menu selection.
Available alphanumeric characters:

A B C D E F G H I J K L M N O P Q(q) R S T U V W X
Y Z (space) + – / 0 1 2 3 4 5 6 7 8 9
Note: Refer to page 23 to change the Power On message, and

page 43 to register a Memory Channel name.
20
BASIC COMMUNICATIONS
SSB TRANSMISSION FM TRANSMISSION
SSB is the most commonly-used mode on the HF FM is a common mode for communicating on VHF or
Amateur radio bands. Compared with other voice UHF frequencies. As for HF and the 6 m band,
modes, SSB requires only a narrow bandwidth for 29 MHz and 51-54 MHz bands are commonly used
communications. SSB also allows long distance for FM operation. You can also utilize 10 m/ 6 m band
communications with minimum transmission power. repeaters to reach your friends when they are outside
or skipped over from your coverage. Although FM
If necessary, refer to “OPERATING BASICS”,
requires a wider bandwidth when compared to SSB
beginning on page 10, for details on how to receive.
or AM mode, it has the finest audio quality among
1 Select an operating frequency. these modes. When combined with the full-quieting
aspect of FM signals, which suppresses background
2 Press [LSB/USB] until “USB” or “LSB” appears on noise on the frequency, FM can be the best method
the operating mode display. for maintaining casual communications with your local
• If the desired sideband (“USB” or “LSB”) does friends.
not appear, select the other sideband first.
Then, press [LSB/USB]. The mode indicator If necessary, refer to “OPERATING BASICS”,
changes to your desired sideband. beginning on page 10, for details on how to receive.
• “USB” represents the upper sideband and 1 Select an operating frequency.
“LSB” represents the lower sideband. Normally, 2 Press [FM/AM (FM-N)] until “FM” appears.
USB is used for the communications for
10 MHz and above while LSB is used for the • If “FM” does not appear, select “AM”, then press
frequencies below 10 MHz. [FM/AM (FM-N)]. The mode indicator changes
to “FM”.
3 Press [MIC (CAR)] to adjust the Microphone gain.

3 Press and hold Mic [PTT].
• The current gain level appears on the sub-
display. • The TX-RX LED lights red.
• Refer to “VOX” {page 30} for information on
automatic TX/ RX switching.
4 Speak into the microphone in your normal voice.
4 Press and hold Mic [PTT]. • Speaking too close to the microphone or too
loudly may increase distortion and reduce
• The TX-RX LED lights red. intelligibility at the receiving end.
• Refer to “VOX” {page 30} for information on • You can switch the Microphone gain for FM
automatic TX/ RX switching. between 1 (Normal), 2 (Medium), and 3 (High)
5 Speak into the microphone and turn the by using Menu No. 47. 1 (Normal) is usually
MULTI/CH control so that the ALC meter reflects appropriate; however, select 3 (High) if other
your voice level but does not exceed the ALC limit. stations report that your modulation is weak.
• Speak in your normal tone and level of voice. 5 Release Mic [PTT] to return to Reception mode.
Speaking too close to the microphone or too • The TX-RX LED lights green or turns off,
loudly may increase distortion and reduce depending on the SQL control position.
intelligibility at the receiving end.
Refer to “COMMUNICATING AIDS”, beginning on
• You may want to use the Speech Processor.
page 28, for additional information on useful operation
Refer to “SPEECH PROCESSOR” {page 31}
functions.
for details.
Note: Microphone gain adjustment for SSB or AM has no
6 Release Mic [PTT] to return to Reception mode. effect in FM mode. In FM mode, you must select 1 (Normal), 2
(Medium), or 3 (High) in Menu No. 47.
depending on the SQL control position.
7 Press [MIC (CAR)] or [CLR] to exit the Microphone
gain adjustment.
Refer to “COMMUNICATING AIDS”, beginning on
page 28, for information on additional useful operation
functions.
21
5 BASIC COMMUNICATIONS
AM TRANSMISSION NARROW BANDWIDTH FOR FM

Each mode used on the HF Amateur bands has its Select wide band or narrow band TX deviation
own advantages. Although long distance DX contacts depending on whether the other station is using wide
may be less common while using AM, the superior band or narrow band filter for FM mode. While “NAR”
audio quality characteristic of AM operation is one appears, the TS-590S transceiver transmits signals in
reason why some hams prefer this mode. narrow band FM but the reception IF filter bandwidth
remains unchanged (Wide). The deviation selection
If necessary, refer to “OPERATING BASICS”,
is crucial to avoid audio distortion or insufficient
beginning on page 10, for details on how to receive.
intelligibility that the other station will encounter.
1 Select an operating frequency.
1 Press [FM/AM (FM-N)] until “FM” appears.
2 Press [FM/AM (FM-N)] until “AM” appears. • If “FM” does not appear, select “AM” first, then
• If “AM” does not appear, select “FM” first, then press [FM/AM (FM-N)]. The mode indicator
press [FM/AM (FM-N)]. The mode indicator changes to “FM”.
changes to “AM”.
2 Press and hold [FM/AM (FM-N)] to toggle the
selection between wide and narrow TX deviation.
• “ ” appears when narrow TX deviation is
selected.
3 Press [MIC (CAR)] to enter the Microphone gain
adjustment mode.
• The current gain level appears on the sub-
display.
4 Press and hold Mic [PTT].
• The TX-RX LED lights red.
CW TRANSMISSION
• Refer to “VOX” {page 30} for information on CW operators know that this mode is very reliable
automatic TX/ RX switching. when communicating under worst conditions. It may
be true that newer digital modes rival CW as being
5 Speak into the microphone and adjust the equally as useful in poor conditions. These modes,
MULTI/CH control so that the power meter slightly however, do not have the long history of service nor
reflects your voice level. the simplicity that CW provides.
• Speak in your normal tone and level of voice. This transceiver has a built-in electronic keyer that
Speaking too close to the microphone or too supports a variety of functions. For details on using
loudly may increase distortion and reduce these functions, refer to “ELECTRONIC KEYER”
intelligibility at the receiving end. {page 33}.
• You may want to use the Speech Processor. If necessary, refer to “OPERATING BASICS”,
Refer to “SPEECH PROCESSOR” {page 31} beginning on page 10, for details on how to receive.
for details.
1 Select the operating frequency.
6 Release Mic [PTT] to return to Reception mode.
2 Press [CW/FSK (REV)] until “CW” appears.
depending on the SQL control position. • If “CW” does not appear, select “FSK” first, then
press [CW/FSK (REV)]. The mode indicator
7 Press [MIC (CAR)] or [CLR] to exit the Microphone changes to “CW”.
gain adjustment mode.
• To precisely tune in another station, use Auto
Refer to “COMMUNICATING AIDS”, beginning on Zero-beat. Refer to “AUTO ZERO-BEAT”
page 28, for information on additional useful operation {page 23}.
functions.
Note: When the TX power meter reading exceeds the value that
you specified in the TX Power setting {page 56}, decrease the
microphone gain or adjust your tone and level of voice.
3 Press [SEND].
• The TX-RX LED lights red.
4 Operate the Keys or Paddle.
• As you transmit, you should hear a sidetone
that lets you monitor your own transmission.
5 Press [SEND] to return to Reception mode.
depending on the SQL control setting.
22
5 BASIC COMMUNICATIONS
AUTO ZERO-BEAT CARRIER LEVEL

Use Auto Zero-beat before transmitting to tune in a When using AM, CW, or FSK mode, you can adjust
CW station. Auto Zero-beat automatically and exactly the carrier level.
matches your transmit frequency with the station you
are receiving. Neglecting to do this will reduce your 1 Press and hold [MIC (CAR].
chances of being heard by the other station. • The current gain level appears on the sub
display.
1 Tune to the CW signal using the Tuning control.
2 Press [CW T. (AGC OFF)] to start Auto Zero-beat
while CW is selected for the operating mode.
• “CW TUNE” appears.
2 Turn the MULTI/CH control so that the ALC meter
reads within the limits of the ALC zone.
• For AM mode, adjust the MULTI/CH control so
that the ALC meter just begins to indicate.
• Your reception frequency automatically
changes so that the pitch (tone) of the received 3 Press and hold [MIC (CAR] again or press [CLR]
signal exactly matches the TX sidetone/ RX to complete the setting.
pitch frequency that you have selected. Refer
to “TX SIDETONE/ RX PITCH FREQUENCY”
{below}. POWER ON MESSAGE
• When matching is completed, “CW TUNE” Each time you switch the transceiver ON,
disappears. “KENWOOD” (default) appears on the sub display
for approximately 2 seconds. You can program your
• If matching is unsuccessful, the previous
favorite message in place of the default message.
frequency is restored.
You can enter a message using up to 8 characters.
3 To quit Auto Zero-beat, press [CW T. (AGC OFF)]
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
or [CLR].
turn the MULTI/CH control to access Menu No 87.
Note:
◆ When using Auto Zero-beat, the matching error is normally 2 Press [M.IN]/ [SCAN (SG.SEL)] to begin editing
within ±5 Hz. the message.
◆ Auto Zero-beat may fail if the keying speed of the target
station is too slow or if some interference is present.
3 Move the cursor to the left or right by pressing [Q-
◆ When the RIT function is ON, only RIT frequencies change
M.IN] or [Q-MR].
to make the Auto Zero-beat adjustment.
TX SIDETONE/ RX PITCH FREQUENCY

As you send CW, you will hear tones from 4 Press [M.IN]/ [SCAN (SG.SEL)] or turn the
the transceiver speaker. These are called TX MULTI/CH control to select your desired character.
(transmission) sidetones. Listening to these tones,
you can monitor what you are transmitting. You may • You can delete the selected character by
also use the tones to ensure that your key contacts pressing [CL].
are closing, the keyer is functioning, or to practice 5 Repeat steps 3 and 4 to enter the remaining
sending without actually putting a signal on the air. characters.
RX (reception) pitch refers to the frequency of CW 6 Press [MENU] to set the entry and exit character
that you hear after tuning in a CW station. entry mode.
On this transceiver, the frequency of the sidetone and • Press [CLR] at any time to cancel character
RX pitch are equal and selectable. Access Menu No. entry mode and exit the Menu mode.
34 to select the frequency that is most comfortable for
you. The selectable range is from 300 Hz to 1000 Hz
in steps of 50 Hz (default is 800 Hz).
To change the volume of the TX sidetone, access
Menu No. 4. The selections range from 1 to 9 and
OFF (default is 5).
Note:
◆ The position of the AF control does not affect the volume of
the TX sidetone.
◆ When changing the CW pitch/ side tone, the shift amount
of the receive filter is automatically applied to the CW pitch/
side tone. (In Quick Memory mode, the CW pitch/ side tone
is not revised since the receive filter information stored in the
Quick Memory has priority.)
23
ENHANCED COMMUNICATIONS
SPLIT-FREQUENCY OPERATION TF-SET (TRANSMISSION FREQUENCY SET)
Usually you can communicate with other stations TF-SET allows you to temporarily switch your
using a single frequency for receiving and transmission frequency and reception frequency.
transmitting. In this case, you select only one Canceling this function immediately restores the
frequency on either VFO A or VFO B. However, there original transmission and reception frequencies.
are cases where you must select one frequency for By activating TF-SET, you can listen on your transmit
receiving and a different frequency for transmitting. frequency, and change it while listening. This allows
This requires the use of 2 VFOs. This is referred to you to check whether or not the newly selected
as “split-frequency operation”. One typical case which transmission frequency is free of interference.
requires this type of operation is when you use an FM 1 Configure split-frequency operation as explained in
repeater {page 25}. Another typical case is when you the previous section.
call a rare DX station.
2 Press and hold [TF-SET], then turn the Tuning
When a rare or desirable DX station is heard, that control or press Mic [UP]/ [DWN] to change the
operator may immediately get many simultaneous transmission frequency.
responses. Often, such a station is lost under the noise
and confusion of many calling stations. If you find that
you are suddenly being called by many operators, it
is your responsibility to control the situation. You may
announce that you will be “listening up 5 (kHz, from • The transceiver receives on the frequency as
your present transmission frequency)”, or “listening you change, but the frequency shown on the
down between 5 and 10 (kHz)”. sub-display (the original reception frequency)
1 Press [A/B (A=B)] to select VFO A or VFO B. stays unchanged.
• “ ” or “ ” appears to show which VFO is 3 Release [TF-SET].
selected. • You are now receiving again on your original
2 Select an operating frequency. reception frequency.
• This frequency will be used for transmission. Successfully contacting a DX station in a pileup
• To copy the selected VFO frequency to the often depends on making a well-timed call on a clear
other VFO, press and hold [A/B (A=B)]. frequency. That is, it is important to select a relatively
clear transmission frequency and to transmit at the
3 Press [A/B (A=B)] to select the other VFO. exact instant when the DX station is listening but the
4 Select an operating frequency. majority of the groups aren’t transmitting. Switch
your reception and transmission frequencies by using
• This frequency will be used for reception. the TF-SET function and listen to your transmission
5 Press [SPLIT]. frequency. You will soon learn the rhythm of the
DX station and the pileup. The more proficient you
• “ ” appears. become at using this function, the more DX stations
• Each time you press [A/B (A=B)], the reception you will contact.
and transmission frequencies are swapped. Note:
◆ TF-SET is disabled while transmitting.
◆ You can change the transmission frequency even when the
Frequency lock function is ON.
◆ An RIT offset frequency is not added; however, an XIT offset
6 To quit split-frequency operation, press [SPLIT] frequency is added to the transmit frequency during TF-SET.
again.
• “ ” disappears.
24
6 ENHANCED COMMUNICATIONS
FM REPEATER OPERATION 6 Press [AGC/T (SEL] to turn the Tone function ON

if the repeater requires a subtone.
Most Amateur radio voice repeaters use a separate
reception and transmission frequency. The • “ ” appears.
transmission frequency may be higher or lower than • Refer to “Selecting a Tone Frequency” for more
the reception frequency. In addition, some repeaters details on the subtone {page 26}.
may require the transceiver to transmit a subtone
before the repeater can be used.
Compared to simplex communication, you can
usually transmit over much greater distances by
• To quit the Subtone function, press [AGC/T (SEL)]
using a repeater. Repeaters are typically located
twice.
on a mountain top or other elevated location. Often
they operate at higher ERP (Effective Radiated 7 Press [SPLIT].
Power) than a typical station. This combination of • “ ” appears.
elevation and high ERP allows communications over
considerable distances. 8 Press [A/B (A=B)] to return to the original
reception frequency.
HF/ 6 m band repeaters usually operate in the
29 MHz FM sub-band and 51-54 MHz band. This
special service combines the advantages of FM
operation, good fidelity with noise and interference
immunity, with the excitement of HF DX (long
distance) communications. Even on a quiet day, 9 Press Mic [PTT] to transmit.
10 m FM provides reliable around-town • The VFO changes to the other VFO to transmit.
communications with the potential for sudden DX from • Each time you press [A/B (A=B)], the reception
across the country or around the world. and transmission frequencies are swapped.
Note:
10 Press [SPLIT] to quit split-frequency operation.
◆ When programming 2 separate frequencies using 2 VFOs,
be sure to select FM mode on both VFOs. • “ ” disappears.
◆ When operating through a repeater, over deviation caused
by speaking too loudly into the microphone can cause your The data that you select in steps 1 to 8 can be stored
signal to “talk-off” (break up) through the repeater. in memory. Refer to “Split-Frequency Channels”
{page 41}.
Note:
29.520 MHz ◆ When operating through a repeater, over deviation caused
88.5 Hz by speaking too loudly into the microphone can cause your
29.620 MHz
signal to “talk-off” (break up) through the repeater.
◆ To check the tone frequency stored in a memory channel,
recall the desired memory channel and press [AGC/T
29.620 MHz (SEL)].
29.520 MHz
88.5 Hz
TRANSMITTING A TONE
In general, FM repeaters require the transceiver to
transmit a sub-audible tone to prevent other repeaters
on the same frequency from locking each other up.
The required tone frequency differs among repeaters.
Repeaters also differ in their requirements for either
continuous or burst tones. For the appropriate
selections for your accessible repeaters, consult your
local repeater reference.
1 Press [A/B (A=B)] to select VFO A or VFO B. After completing the tone settings, pressing and
• “ ” or “ ” appears to show which VFO is holding Mic [PTT] causes the transceiver to transmit
selected. the selected tone. If you have selected a 1750 Hz
2 Turn the Tuning control or the MULTI/CH control tone, the transceiver sends a 500 ms tone burst each
to select the reception frequency. time transmission starts.
Note: If you store tone settings in a memory channel, you need
3 Press [FM/AM (FM-N)] to select FM mode. not reprogram each time. Refer to “MEMORY FEATURES”
{page 41}.
4 Press and hold [A/B (A=B)] to duplicate the
frequencies and other data to the other VFO.
5 Turn the Tuning control or the MULTI/CH control
to select the transmission frequency.
25
■ Activating the Tone Function TONE FREQUENCY ID SCAN

1 Confirm that FM mode has been selected on This function scans through all tone frequencies to
the VFO(s) {page 10}. identify the incoming tone frequency on a received
• When using 2 VFOs, you must select FM signal. You may find this useful when you do not
mode on both VFOs. know the tone frequency that the repeater uses.
2 Press [AGC/T (SEL)]. 1 While the Tone function is ON (“ ” is visible), press
and hold [AGC/T (SEL)].
• “ ” appears.
• The current tone frequency appears.
2 Press [SCAN (SG.SEL)] to activate the Tone
frequency ID scan.
Note: You cannot use the Tone function with the CTCSS • While the transceiver is receiving a signal, “ ”
function. blinks and every tone frequency is scanned.
When the tone frequency is identified, the
■ Selecting a Tone Frequency transceiver stops scanning and the identified
frequency is displayed.
1 While “ ” appears (Tone function is ON), press
and hold [AGC/T (SEL)].
• The current tone frequency appears.
The default is 88.5 Hz.
• Press [SCAN (SG.SEL)] or [CLR] to stop
scanning while the tone frequency ID scan is
active.
• Press [SCAN (SG.SEL)] again to resume
2 Turn the MULTI/CH control to select the desired scanning.
tone frequency. Note: Received signals are audible while scanning is in
• The available tone frequencies are listed in progress.
the table below.
3 Press and hold [AGC/T (SEL)] or press [CLR]
to complete the setting. FM CTCSS OPERATION
You may sometimes want to hear calls only from
Freq. Freq. Freq. Freq. specific persons. When using FM mode, the
No. No. No. No. Continuous Tone Coded Squelch System (CTCSS)
(Hz) (Hz) (Hz) (Hz)
allows you to ignore (not hear) unwanted calls from
00 67.0 11 97.4 22 141.3 33 206.5 other persons who are using the same frequency.
01 69.3 12 100.0 23 146.2 34 210.7 A CTCSS tone is sub-audible and is selectable from
among the 42 tone frequencies. Select the same
02 71.9 13 103.5 24 151.4 35 218.1 CTCSS tone as the other stations in your group. You
03 74.4 14 107.2 25 156.7 36 225.7 will not hear calls from stations other than those using
the same CTCSS tone.
04 77.0 15 110.9 26 162.2 37 229.1
Note: CTCSS does not cause your conversation to be private.
05 79.7 16 114.8 27 167.9 38 233.6 It only relieves you from listening to unwanted conversations.
06 82.5 17 118.8 28 173.8 39 241.8
07 85.4 18 123.0 29 179.9 40 250.3 1 Press [A/B (A=B)] to select VFO A or VFO B.
08 88.5 19 127.3 30 186.2 41 254.1 • “ ” or “ ” appears to show which VFO is
selected.
09 91.5 20 131.8 31 192.8 42 1750
2 Select the 29 MHz band or the 51-54 MHz band
10 94.8 21 136.5 32 203.5 -- -- using [28 (9)] or [50 (0)].
Note:
3 Select the desired frequency with the Tuning
◆ You can select a tone frequency independent of a
control or MULTI/CH control.
CTCSS frequency. 4 Press [FM/AM (FM-N)] to select FM mode.
◆ When 1750 Hz is selected, the transceiver sends a
500 ms tone burst each time transmission starts. You 5 Turn the SQL control to adjust the squelch.
cannot transmit 1750 Hz tone manually.
6 Press [AGC/T (SEL)] until “ ” appears.
7 While “ ” is visible, press and hold [AGC/T

(SEL)].
• The current CTCSS frequency appears (default
is 88.5 Hz).
26
• Press [SCAN (SG.SEL)] or [CLR] to stop

scanning while the CTCSS frequency ID scan is
active.
• Press [SCAN (SG.SEL)] again to resume
8 Turn the MULTI/CH control to select the scanning.
appropriate CTCSS frequency.
Note: Received signals are audible while scanning is in
• The selectable CTCSS frequencies are listed in progress.
the table below.
9 Press and hold [AGC/T (SEL)] or press [CLR] to
complete the setting. CROSS TONE
Use this feature when using different uplink and
Freq. Freq. Freq. Freq. downlink tones to access a repeater. You can set a
No. No. No. No.
(Hz) (Hz) (Hz) (Hz) transmission Tone frequency and reception CTCSS
frequency to different frequencies.
00 67.0 11 97.4 22 141.3 33 206.5
01 69.3 12 100.0 23 146.2 34 210.7 To set the transmission tone:
02 71.9 13 103.5 24 151.4 35 218.1
1 Press [A/B (A=B)] to select VFO A or VFO B.
03 74.4 14 107.2 25 156.7 36 225.7
2 Select your desired transmission frequency.
04 77.0 15 110.9 26 162.2 37 229.1
3 Press [FM/AM (FM-N)] to select FM.
05 79.7 16 114.8 27 167.9 38 233.6
06 82.5 17 118.8 28 173.8 39 241.8
5 Press and hold [AGC/T (SEL)], then rotate the
07 85.4 18 123.0 29 179.9 40 250.3
MULTI/CH control to select your desired Tone
08 88.5 19 127.3 30 186.2 41 254.1 frequency.
09 91.5 20 131.8 31 192.8 -- -- 6 Press and hold [AGC/T (SEL)] or press [CLR] to
10 94.8 21 136.5 32 203.5 -- -- complete the setting.
You will hear calls only when the selected tone is To set the reception tone:
received. To answer the call, press and hold Mic
[PTT], then speak into the microphone. 1 Press [A/B (A=B)] to select the other VFO.
Skip steps 7 and 8 if you have already programmed 2 Select your desired reception frequency.
the appropriate CTCSS frequency. 3 Press [FM/AM (FM-N)] to select FM.
Note:
◆ When using split-frequency operation, select FM mode on
both VFOs to use CTCSS. 5 Press and hold [AGC/T (SEL)], then rotate the
◆ You can select a CTCSS frequency independent of a tone MULTI/CH control to select your desired CTCSS
frequency.
frequency.
◆ You cannot use the CTCSS function with the Tone function.
6 Press and hold [AGC/T (SEL)] or press [CLR] to
complete the setting.
CTCSS FREQUENCY ID SCAN
To set the Cross tone:
This function scans through all CTCSS frequencies to
identify the incoming CTCSS frequency on a received 1 Press [SPLIT].
signal. You may find this useful when you cannot • “SPLIT” appears on the display.
recall the CTCSS frequency that the other persons in
your group are using. 2 Press [AGC/T (SEL)] until “ ” appears.
Note: hen the cross tone function is ON, the Tone and CTCSS
1 While the CTCSS function is ON, press and hold frequency cannot be changed. To change the Tone or CTCSS
[AGC/T (SEL)]. frequency, press [AGC/T (SEL)] to turn Tone or CTCSS ON,
then change the setting.
• The current CTCSS frequency appears.
2 Press [SCAN (SG.SEL)] to activate the CTCSS
frequency ID scan.
• While the transceiver is receiving a signal, “ ”
blinks and every CTCSS frequency is scanned.
When the CTCSS frequency is identified, the
transceiver stops scanning and the identified
frequency is displayed.
27
COMMUNICATING AIDS
RECEPTION Note: When entering a frequency using the numeric
keys, if you turn the MULTI/CH control in the middle of the
frequency entry, the frequency will be entered into the log.
SELECTING YOUR FREQUENCY
In addition to turning the Tuning control or pressing ■ Using the MHz key
Mic [UP]/ [DWN], there are several other ways You can use the MULTI/CH control to change the
to select your frequency. This section describes operating frequency in steps of 1 MHz.
additional methods of frequency selection that may
save you time and effort. 1 Press [MHz].
■ Direct Frequency Entry
When the desired frequency is far removed from
the current frequency, directly entering a frequency
from the numeric keypad is usually the fastest
method. 2 Turn the MULTI/CH control.
• Clockwise increases the frequency and
1 Press [ENT].
counter-clockwise decreases the frequency.
• “ - - . - - - . - - ” appears.
3 Press [MHz] again to exit.
• “ ” disappears.
If you prefer to change the frequency in steps of
100 kHz or 500 kHz, rather than 1 MHz, access
2 Press the numeric keys ([50 (0)] to [28 (9)]) to Menu No. 10 and select 100 kHz, 500 kHz, or
enter your desired frequency. 1 MHz.
• Pressing [ENT] at any time fills the Note: Even if 100 kHz or 500 kHz is assigned for the [MHz]
remaining digits (the digits you did not enter) key, “ ” appears on the display.
with 0 and completes the entry.
To select 1.85 MHz for example, press ■ Quick QSY
[ENT], [50 (0)], [1.8 (1)], [24 (8)], [14 (5)],
then press [ENT] to complete the input (6 To move up or down the frequency quickly, use the
key strokes). MULTI/CH control. Turning this control changes
the operating frequency in steps of 5 kHz for SSB/
• Pressing [CLR] before pressing [ENT] CW/ FSK/ AM and steps of 10 kHz for FM.
cancels the entry and restores the current
VFO frequency. • If you want to change the default frequency
step size, access Menu No. 14 (SSB/CW/FSK),
Note:
15 (AM), or 16 (FM). Press [M.IN]/ [SCAN (SG.
◆ You can enter a frequency in the range of 30.00 kHz
to 59.999.99 MHz. Refer to the specifications for the SEL)] to select 500 Hz, 1 kHz, 2.5 kHz, 5 kHz,
available frequency range. or 10 kHz for SSB/ CW/ FSK, and 5 kHz, 6.25
◆ Attempting to enter a frequency that is outside the kHz, 10 kHz, 12.5 kHz, 15 kHz, 20 kHz, 25 kHz,
selectable frequency range causes an alarm to sound 30 kHz, 50 kHz, or 100 kHz for AM/ FM. The
and the entered frequency is rejected.
default frequency step size is 5 kHz for SSB/
◆ When the entered frequency does not meet the current
VFO frequency step size requirement, the nearest CW/ FSK/ AM and 10 kHz for FM.
available frequency is automatically selected after the • When changing the operating frequency by
entered frequency is changed.
using the MULTI/CH control, frequencies
◆ When the 10 Hz digit (last displayed digit) is entered,
the digit 0 is automatically entered for the 1 Hz digit, are rounded such that new frequencies are
and frequency entry is completed. The 1 Hz digit is not multiples of the frequency step size. To disable
displayed. this function, access Menu No. 12 and select
◆ When an entered frequency is accepted, RIT or XIT will “oFF” (default is ON).
be switched OFF, but the RIT or XIT offset frequency is
not cleared. • Within the AM broadcast band, the step size
automatically defaults to the frequency step
■ Frequency Entry History value in Menu No. 13. This frequency step size
can be switched between 9 kHz (“on”) and
The last 10 frequencies you entered are stored in
5 kHz (“oFF”) via Menu No. 13.
the Frequency Entry History. You can access the
history to easily re-enter a recently used frequency. Note: The programmed frequency step size for the
MULTI/CH control is stored independently for the HF and
1 Press [ENT]. 50 MHz bands. You can also set a different frequency step
size for SSB/ CW/ FSK, AM and FM modes.
2 Turn the MULTI/CH control.
• The entered frequency along with its log
number appears. The most recent entered
frequency is logged as number E0 and the
oldest frequency is logged as number E9.
3 Press [ENT] to set the selected frequency to
the VFO.
28
7 COMMUNICATING AIDS
■ Fine Tuning RIT (RECEIVE INCREMENTAL TUNING)

The default frequency step size when turning the RIT provides the ability to change your reception
Tuning control to change the frequency is 10 frequency by ±9.99 kHz in steps of 10 Hz without
Hz for SSB/ CW/ FSK, and 100 Hz for AM/ FM. changing your transmission frequency. If the Fine
However, you can change the frequency step size Tuning ([FINE (F.LOCK)]) function is ON, the
to 1 Hz for SSB/ CW/ FSK, and 10 Hz for AM/ FM. frequency step size becomes 1 Hz (±9.999 kHz). RIT
works equally well with all modulation modes and
1 Press [FINE (F.LOCK)].
while using VFO or Memory Recall mode.
1 Press [RIT].
• “ ” and the RIT offset appear.
2 Turn the Tuning control to select the exact

frequency.
2 If required, press [CL] to reset the RIT offset to 0.
3 To quit the function, press [FINE (F.LOCK)]
again. 3 Turn the RIT/ XIT control to change your reception
• “ ” disappears. frequency.
4 To turn RIT OFF, press [RIT].
■ Tuning Control Adjustment Rate • The reception frequency is returned to the
The default Tuning control adjustment rate is 500. frequency that was selected prior to step 1.
This represents the number of pulses the Tuning Note: When storing the frequency in a Memory channel with
control generates in a complete revolution. Each the RIT function ON, the RIT offset frequency is added to or
pulse changes the tuning frequency based on the subtracted from the VFO frequency. The calculated data is then
stored in the Memory channel.
current frequency step size (the frequency step
size for the Tuning control is 10 Hz for SSB/ CW/
FSK and 100 Hz for AM/ FM). For example, in AGC (AUTOMATIC GAIN CONTROL)
SSB mode the frequency step size is 10 Hz, so the When using a mode other than FM, AGC selects the
frequency would change by 5,000 Hz in a complete time constant for the Automatic Gain Control circuit.
revolution of the Tuning control. The adjustment
rate of the Tuning control can be lowered to 250 Selecting a slow time constant will cause the receiver
pulses per revolution or increased to 1000 pulses gain and S-meter readings to react slowly to large
per revolution. input changes. A fast time constant causes the
receiver gain and the S-meter to react quickly to
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or changes in the input signal. A fast AGC setting is
turn the MULTI/CH control to select Menu No. particularly useful in the following situations:
11.
• Tuning rapidly
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “250”,
• Receiving weak signals
“500”, or “1000” (default).
• Receiving high-speed CW
For your convenience, the following default AGC time
■ Equalizing VFO Frequencies (A=B) constant has already been programmed.
This function allows you to copy the frequency and SSB: Slow (“ ”) CW: Fast (“ ”)
modulation mode of the active VFO to the inactive FSK: Fast (“ ”) AM: Slow (“ ”)
VFO.
1 Select the frequency and mode on VFO A or ■ AGC Time Constant Adjustment
VFO B. You can pre-set up to 20 values (1 ~ 20) for the
2 Press and hold [A/B (A=B)]. FAST/SLOW time constant (release time).
• The frequency and mode selected in step 1 To change the default time constant:
are duplicated to the inactive VFO.
1 Press [AGC/T (SEL)] to select FAST or SLOW.
3 Press [A/B (A=B)] to confirm that the frequency • The AGC time constant icon appears on the
was copied to other VFO. display (“ ”: Slow, “ ”: Fast).
2 Press and hold [AGC/T (SEL)] to display the
time constant pre-set value.
3 Turn the MULTI/CH control to set your desired
time constant value.
4 If you want to turn the AGC OFF, press and
hold [CW T. (AGC OFF)].
• “ ” appears on the display.
Note: You cannot adjust the time constant in FM mode.
29
TRANSMISSION ■ Delay Time

If the transceiver returns to reception mode too
VOX (VOICE-OPERATED TRANSMISSION) quickly after you stop speaking, your final word
VOX eliminates the necessity of manually switching may not be transmitted. To avoid this, select an
to the transmission mode each time you want to appropriate delay time that allows all of your words
transmit. The transceiver automatically switches to to be transmitted without an overly long delay after
transmission mode when VOX senses that you have you stop speaking.
begun speaking into the microphone. 1 Select USB, LSB, FM, or AM mode.
When using VOX, develop the habit of pausing 2 Press [VOX (LEV)] to switch the VOX function ON.
between thoughts to allow the transceiver to drop
back to reception mode briefly. You will then hear if
anybody wants to interrupt, plus you will have a short 3 Press and hold [KEY (DELAY)].
period to gather your thoughts before speaking again. • The current setting appears on the
Your listeners will appreciate your consideration as sub-display. The default is 50 (1500 ms).
well as respect your more articulate conversation.
Press [VOX (LEV)] to toggle between VOX ON and
OFF.
• “ ” appears when the VOX function is ON. 4 While speaking into the microphone using your
normal tone of voice, turn the MULTI/CH control
such that the transceiver switches to reception
mode after you have stopped talking.
• The selectable range is from 5 to 100
■ Microphone Input Level (150 ms to 3000 ms) in steps of 5, or OFF.
To enjoy the VOX function, take the time to 5 Press [CLR] to store the parameter and exit the
properly adjust the VOX gain. This level controls setting mode.
the capability of VOX to detect the presence or
absence of your voice. ■ Anti-VOX Adjustment
In CW mode, this level cannot be adjusted. The TS-590S transceiver has a DSP IC to improve
1 Select USB, LSB, FM, or AM mode. and customize incoming/ outgoing audio signals.
When the VOX function is turned ON, the DSP
2 Press [VOX (LEV)] to switch the VOX function IC adjusts the Anti-VOX level automatically,
ON. comparing the reception sound level and
• “ ” appears. microphone input level. So, you never have to
worry about adjusting the anti-VOX level.
Note: When connecting a headphone to the Phone jack,
Anti-VOX will not function.
3 Press and hold [VOX (LEV)]. ■ Data VOX

• The current VOX gain level appears on the Although the microphone is normally used for
sub-display. VOX transmission, you can also utilize the audio
input of the ACC2 or USB connector. When the
transceiver detects an audio signal on the ACC2
or USB connector, it automatically transmits.
You can select ACC2 or USB via Menu No. 63
4 While speaking into the microphone using (“Selecting a Data Transmission Line”) {page 58}.
your normal tone of voice, adjust the setting 1 Select USB, LSB, FM, or AM mode.
(default is 4) using the MULTI/CH control until
the transceiver reliably switches to transmission 2 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
mode each time you speak. turn the MULTI/CH control to select Menu No.
69.
• The selectable gain range is from 0 to 9.
• The setting should not allow background 3 Press [M.IN] to set the VOX with DATA input
noise to switch the transceiver to transmit function ON.
mode. 4 If necessary, adjust the VOX gain level for the
Note: The VOX gain level can be adjusted even if VOX is ACC2 or USB connector {page 31}.
switched OFF or while you are transmitting. Note: While VOX with DATA input is set to ON (Menu No.
69), speaking into the microphone also activates the VOX
function and you can still transmit using Mic [PTT]. Anti-
VOX does not function with Data VOX.
While the Data VOX function remains ON and the

transceiver is connected to a sound source, such as a PC,
the transceiver may begin transmitting due to the sounds
emitted from the sound source. To avoid unintended
transmission while the transceiver is connected to the
sound source, turn the Data VOX function OFF.
30
■ Data VOX Delay Time • Using higher compression will not improve
your signal clarity or apparent signal strength.
Select an appropriate delay time for after the audio
Excessively compressed signals are more
signal input to the ACC2 or USB connector ends.
difficult to understand due to distortion and are
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or less pleasant to hear than signals with less
turn the MULTI/CH control to select Menu No. compression.
70.
5 Press and hold [PROC (LEV)] to exit the Speech
2 Press [M.IN]/ [SCAN (SG.SEL)] to set your Processor input level adjustment mode.
desired delay time.
6 Press [MIC (CAR)] to enter the Speech Processor
3 Press [MENU] to exit Menu mode. output level adjustment mode.
• As you speak into the microphone, turn the
■ USB/ ACC2 VOX Gain MULTI/CH control so that the ALC meter
When using the ACC2 or USB connector for VOX reflects according to your voice level, but does
transmission, take the time to properly adjust the not exceed the ALC limit. Press [MIC (CAR)] to
VOX gain. exit when you finish the adjustment.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] ■ Speech Processor Effect
or turn the MULTI/CH control to select Menu
No. 71 (USB connector) or Menu No. 72 (ACC2 When using the Speech Processor, you can
connector). change its effect.
2 While sending an audio signal to the ACC2 or 1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
USB connector, adjust the value (default is 4) turn the MULTI/CH control to select Menu No.
using [M.IN]/ [SCAN (SG.SEL)] until the 29.
transceiver reliably switches to transmit mode 2 Press [M.IN]/ [SCAN (SG.SEL)] to set the
each time you send an audio signal to the Processor Effect to SOFT or HARD (default).
connector.
XIT (TRANSMIT INCREMENTAL TUNING)
SPEECH PROCESSOR
Similar to RIT, XIT provides the ability to change your
The Speech Processor levels out large fluctuations in transmission frequency by ±9.99 kHz in steps of
your voice while you speak. When using SSB, AM, or 10 Hz without changing your reception frequency. If
FM mode, this leveling action effectively raises the Fine Tuning function is ON, the frequency step
the average TX power (SSB/AM) or raises the size becomes 1 Hz (±9.999 kHz).
deviation to an adequate level (FM), resulting in a
more understandable signal. The amount of voice 1 Press [XIT].
compression is fully adjustable. Using the Speech • “ ” and the XIT offset appear.
Processor makes it easier to be heard by distant
stations.
Level
2 If required, press [CL] to reset the XIT offset to 0.

Speech Time
Processor 3 Turn the RIT/ XIT control to change your transmit
OFF frequency.
Level
4 To turn XIT OFF, press [XIT].

Speech Time
Processor • “ ” and the offset frequency disappear. The
ON transmission frequency is returned to the
frequency that was selected prior to step 1.
Note:
1 Select USB, LSB, AM, or FM mode. ◆ If the Fine Tuning function is ON, you can adjust the
frequency within ±9.99 kHz.
2 Press [PROC (LEV)] to turn the Speech Processor ◆ The frequency shift set by the XIT control is also used by the
ON. RIT function. Therefore, changing or clearing the XIT offset
also affects the RIT offset.
• “ ” appears. ◆ When the XIT frequency goes beyond the available
transmission frequency, the transceiver automatically stops
3 Press and hold [PROC (LEV)] to enter the Speech transmitting.
Processor input level adjustment mode.
4 As you speak into the microphone, turn the
MULTI/CH control so that the compression meter
indicates that the compression level is around
10 dB while you speak.
31
CUSTOMIZING TRANSMISSION SIGNAL Frequency Response Curves

Amplitude oFF
CHARACTERISTICS Hb2
HP
The quality of your transmission signal is important, bb1
c
regardless of which on-air activity you pursue.
However, it is easy to be casual and overlook this fact
since you don’t listen to your own signal.
The following sub-sections provide information that
will help you tailor your transmission signal.
0.1 1.0 2.0
Audio frequency (kHz)
■ TX Filter Bandwidth (SSB/ AM)
Use Menu No. 25 to select one of the following TX Note: When using the ARCP-590, you can temporarily change
low-cut filters: 10, 100, 200, 300 (default), 400, or each preset value.
500 Hz.
Use Menu No. 26 to select one of the following TX TRANSMIT INHIBIT
high-cut filters: 2500, 2600, 2700 (default), 2800, Transmit Inhibit prevents the transceiver from being
2900, or 3000 Hz. placed in transmission mode. No signal can be
transmitted when this function is ON, even if Mic [PTT]
■ TX Filter Bandwidth (LSB-DATA/ USB-DATA) is pressed.
Use Menu No. 27 to select one of the following TX • TX Inhibit OFF: Transmission is allowed.
low-cut filters: 10, 100, 200, 300 (default), 400, or • TX Inhibit ON: Transmission is not allowed.
500 Hz.
Switch this function ON or OFF via Menu No. 60.
Use Menu No. 28 to select one of the following TX The default is OFF.
high-cut filters: 2500, 2600, 2700 (default), 2800,
2900, or 3000 Hz.
BUSY LOCKOUT
■ TX Equalizer (SSB/ AM/ FM) Busy Lockout prevents the transceiver from being
placed in transmit mode if the current operating
Use Menu No. 30 to change the transmission frequency is busy; in other words, if the squelch is
frequency characteristics of your signal. You can open, you cannot transmit.
select from 1 of 6 different transmission profiles
including the default flat response. Selecting any • Busy Lockout OFF: Transmission is allowed.
of the following items from the Menu causes • Busy Lockout ON: Transmission is not allowed.
“ ” to appear on the display.
Switch this function ON or OFF via Menu No. 74.
• Off (oFF): The default is OFF.
The flat frequency response for SSB, FM, and
AM (default). CHANGING FREQUENCY WHILE TRANSMITTING
• High boost 1 (Hb1)/ High boost 2 (Hb2): Moving your frequency while transmitting is usually an
unwise practice due to the risk of interfering with other
Emphasizes higher audio frequencies; effective stations. However, if necessary, by using the Tuning
for a bassi voice. High boost 2 does not reduce control you can change the operating frequency while
the low frequency as much as High boost 1. transmitting. You also can change the XIT offset
• Formant pass (FP): frequency while in transmission mode.
Improves clarity by suppressing audio While transmitting, if you select a frequency outside
frequencies outside the normal voice frequency the transmission frequency range, the transceiver is
range. automatically forced to return to reception mode.
• Bass boost 1 (bb1)/ Bass boost 2 (bb2):
Emphasizes lower audio frequencies;
effective for a voice with more high frequency
components. Bass boost 2 emphasizes more
low frequency response.
• Conventional (c):
Emphasizes by 3 dB frequencies at 600 Hz and
higher.
• User (U):
Reserved for the optional ARCP software.
Off (oFF) is programmed at the factory as a
default.
32
CW BREAK-IN ELECTRONIC KEYER

Break-in allows you to transmit CW without manually This transceiver has a built-in electronic keyer that
switching between transmission and reception modes. can be used by connecting a keyer paddle to the
Two types of Break-ins are available: Semi Break-in transceiver’s rear panel. Refer to “Keys for CW
and Full Break-in. (PADDLE and KEY)” {page 2} for details regarding
this connection. The built-in keyer supports lambic
Semi Break-in:
(squeeze) operation.
When the key contacts open, the transceiver
automatically waits for the duration of the time
period you selected. The transceiver then returns to ELECTRONIC KEYER MODE
reception mode. There are 2 modes of operation when using an
Full Break-in: electronic keyer for lambic keying operation. Mode A
As soon as the key contacts open, the transceiver completes the current key sequence you are sending
returns to reception mode. when you release the paddles. Mode B sends one
more key, opposite the current key you are sending,
upon releasing the paddles.
USING SEMI BREAK-IN OR FULL BREAK-IN
1 Press [CW/FSK (REV)] until you select CW mode.
turn the MULTI/CH control to select Menu No. 32.
• “CW” appears.
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “A” or “B”
2 Press [VOX (LEV)]. (default).
• “ ” appears. 3 Press [MENU] to exit Menu mode.
3 Press and hold [KEY (DELAY)].
• The current setting (FBK or delay time) CHANGING KEYING SPEED
appears. The default is 50 (500 ms). The keying speed of the electronic keyer is fully
adjustable. Selecting the appropriate speed is
important in order to send error-free CW that other
operators can copy solidly. Selecting a speed that is
beyond your keying ability will only result in mistakes.
4 Turn the MULTI/CH control to select “FBK” (Full You will obtain the best results by selecting a speed
Break-in) or a delay time for Semi Break-in. that is close to the speed used by the other station.
• Delay time ranges from 5 to 100 (50 ms to 1 Press [CW/FSK (REV)] until you select CW mode.
1000 ms) in steps of 5.
• “CW” appears.
2 Press [KEY (DELAY)].
• The current keying speed appears. The default
is 20 (wpm).
5 Begin sending.
• The transceiver automatically switches to
transmission mode.
• When FBK (Full Break-in) is selected:
The transceiver immediately switches to 3 While keying the paddle and listening to the TX
reception mode when the key opens. (transmission) sidetone, turn the MULTI/CH control
to select the appropriate speed.
• When a delay time is selected:
The transceiver switches to reception mode • The speeds range from 4 to 60 wpm, in steps of
after the delay time that you have selected has 1 wpm. The larger the number, the faster the
passed. speed.
6 Press [CLR] to exit. 4 Press [KEY (DELAY)] again to complete the

setting.
Note: FBK (Full Break-in) cannot be used with the TL-922/
922A linear amplifier. Note: When using the semi-automatic “Bug” function, the
selected speed applies only to the rate that dots are sent.
■ Invalid Break-In Operation

You can make break-in operation invalid while
performing the keying speed adjustment.
To switch this function ON, access Menu No. 43,
and select “on” (default is “oFF”).
• “VOX” blinks when break-in operation is
enabled.
33
RISE TIME OF CW CW MESSAGE MEMORY

The rise time of a CW signal is the time for the RF This transceiver has 4 memory channels for storing
output to rise to its maximum power after the key is CW messages. Each memory channel can store
closed. approximately 50 characters (equivalent of 250 dots).
These memory channels are ideal for storing contest
exchanges that you want to send repeatedly. Stored
messages can be played back to check message
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “1”, “2”, content or for transmitting.
“4”, or “6” (default).
The electronic keyer has a function that allows you
• The default setting of 6 ms is fine for slow or to interrupt playback and manually inject your own
medium keying speeds and normal weighting keying. To switch this function ON, access Menu
(dot/ dash ratio). 1, 2, or 4 ms are good for No. 33 and select “on”. The default is OFF.
faster keying speeds.
The electronic keyer can also repeatedly play back
3 Press [MENU] to exit Menu mode. the message that you stored. To switch this function
ON, access Menu No. 56 and select “on”. The default
is OFF.
AUTO WEIGHTING
For repetitive message playback, you can change
The electronic keyer can automatically change the the interval between each series of messages. Use
dot/ dash weighting. Weighting is the ratio of dash Menu No. 57 and select the time in the range of 0 to
length to dot length. The weighting changes with your 60 seconds, in steps of 1 second.
keying speed automatically, thus making your keying
Note:
easier for other operators to copy (default).
◆ This function cannot be used when the Bug Key function is
Access Menu No. 36 to select “AUto” or “2.5” ~ “4.0” ON.
(in steps of 0.1) fixed weight ratio. The default is ◆ Operating the keyer paddle while Menu No. 33 is OFF,
“auto”. When a fixed weight ratio is selected, the dot/ cancels message playback. Even if message playback does
not stop because of your keying start timing, you can cancel
dash weight ratio is locked, irregardless of the keying playback by pressing [CLR].
speed. ◆ When the constant recording function of the optional VGS-1
is ON, you cannot use [RX/4 (REC)].
■ Reverse Keying Weight Ratio
■ Storing CW Messages
Auto Weighting increases the weighting as you
increase your keying speed. However, the 1 Press [CW/FSK (REV)] until you select CW
electronic keyer also can decrease the weighting mode.
as you increase your keying speed. • “CW” appears.
To switch this function ON, access Menu No. 37, 2 Press and hold [CH1 (REC)], [CH2 (REC)],
and select “on”. The default is OFF. [CH3 (REC)], or [RX/4 (REC)] to select a
When setting Menu No. 36 to “Auto”, refer to the memory channel to be recorded.
following.
Reverse Keying Speed (wpm)

Keying
Weight 4 ~ 24 25 ~ 44 45 ~ 60 • If Constant Recording is ON (Menu No.
55), you cannot store a message to [RX/4
OFF 1:2.8 1:3.0 1:3.2
(REC)] {page 60}. The default is ON.
ON 1:3.2 1:3.0 1:2.8
3 Begin sending using the keyer paddle.
BUG KEY FUNCTION • The message you send is stored in memory.
The built-in electronic keyer can also be used as a

semi-automatic key. Semi-automatic keys are also
known as “Bugs”. When this function is ON, dots are
generated in the normal manner by the electronic 4 To complete the message storage, press [CLR]
keyer. Dashes, however, are manually generated by or [CH1 (REC)]/ [CH2 (REC)]/ [CH3 (REC)]/
the operator by holding the keyer paddle closed for [RX/4 (REC)] to stop.
the appropriate length of time.
• When the number reaches 100(%), the
To switch this function ON, access Menu No. 38 and memory becomes full and recording
select “on”. The default is OFF. automatically stops.
Note: When the Bug Key function is ON, CW Message Memory Note: If you do not operate the keyer paddle after starting to
(see below) cannot be used. record a message, a pause is stored in the channel.
34
■ Checking CW Messages without Transmitting ■ Changing the Inter-message Interval Time

1 Press [CW/FSK (REV)] until you select CW For the message playback repeat, access Menu
mode. No. 56 and select “on”. You can also change the
• “CW” appears. interval playback time of the message. Access
Menu No. 57 and select the time in the range of 0
2 If Break-in is ON, press [VOX (LEV)] to turn to 60 seconds, in steps of 1 second.
VOX OFF. Note: Menu Nos. 56 and 57 settings are shared with the
3 Press [CH1 (REC)], [CH2 (REC)], [CH3 voice communication modes when the optional VGS-1 is
installed.
(REC)], or [RX/4 (REC)] to select the channel
to be played back.
■ Changing the CW Sidetone Volume
• The message is played back.
Turning the AF control does not change the CW
• When Menu No. 56 is “oFF”, press and sidetone playback volume. To change the CW
hold the current playback channel key to sidetone volume, access Menu No. 04 and select
repeatedly play back the message saved “oFF”, or “1” to “9”. The default is “5”.
to that key (a display such as “CP 1111”
appears for the channel key you pressed.). ■ Insert Keying
To cancel the playback, press any channel
key or [CLR]. If you operate a CW keyer manually while playing
• To play back the messages stored in back a recorded CW message, the transceiver
the other channels in sequence, press stops playing back the message. However, during
the corresponding channel keys during contests or regular QSOs, you may sometimes
playback. Up to 4 channels can be queued want to insert a different number or message at a
at the same time. (Repeat playback, certain point in the recorded message.
by pressing and holding the keys, does In this case, first record the CW message as
not work during consecutive message usual {page 34}, without the additional number or
playback.) message you want to insert. Then, access Menu
No. 33 and select “on”.
Now, if you operate a CW keyer while you play
back a recorded message, the transceiver pauses
• While playing back the messages, you can the playback of the recorded message, instead
also adjust the keyer speed by pressing of stopping it. When you finish sending the
[KEY (DELAY)] and turning the MULTI/CH number or message with the keyer, the transceiver
control. resumes playback of the message.
• To interrupt playback, press [CLR].
FREQUENCY CORRECTION FOR CW
■ Transmitting CW Messages
If you operate both SSB and CW modes, you would
Messages can be transmitted using Semi Break-in/ sometimes use SSB mode (USB or LSB) just to
Full Break-in or manual TX/ RX switching. watch and listen to CW signals. It is fine just to
1 Press [CW/FSK (REV)] until you select CW monitor those CW signals but you have experienced
mode. that changing the mode from SSB to CW results in
losing the target CW signal. This is because the
• “CW” appears. frequency on the display always shows the true carrier
2 To use Semi Break-in/ Full Break-in, press frequency for all modes. If you want the transceiver to
[VOX (LEV)]. shift the reception frequency to trace the receiving CW
• “ ” appears. signal when changing the mode from SSB (USB or
LSB) to CW, switch this function ON. The transceiver
• If you are not using Semi Break-in/ Full shifts the reception frequency when changing the
Break-in, press [SEND]. mode from SSB to CW, so you can still hear the target
3 Press [CH1 (REC)], [CH2 (REC)], [CH3 signal and instantly transmit the signal in CW without
(REC)], or [RX/4 (REC)] select the channel to adjusting the frequency.
be played back. 1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
• The message is played back and transmitted turn the MULTI/CH control to select Menu No. 42.
automatically. 2 Press [M.IN] to select “on”.
• To transmit the messages stored in
the other channels in sequence, press
the corresponding channel keys during
playback. Up to 4 channels can be queued
at the same time.
• While playing back the messages, you can
also adjust the keyer speed by pressing
[KEY (DELAY)] and turning the MULTI/CH
control.
• To cancel transmission, press [CLR].
35
AUTO CW TX IN SSB MODE

If you operate both SSB and CW modes, you can
configure the transceiver to change the operating
mode from SSB (USB or LSB) to CW and then
transmit in CW mode automatically when you operate
the CW keyers.
The mode automatically changes from USB to CW
and LSB to CWR, regardless of the setting for Menu
No. 42 (Frequency correction for changing SSB to
CW). Therefore, when the CW signal is received in
SSB mode, you can operate the paddle or keyer to
immediately communicate CW with another station.
turn the MULTI/CH control to access Menu No. 41.
2 Press [M.IN] to select “on”.
Note: You must switch the CW Break-in function ON to change
the mode and transmit in CW mode {page 32}.
MIC UP/ DWN KEY PADDLE MODE

This function allows you to send CW messages
without using an optional paddle {page 2}. The Mic
[UP] key can be used as the dot paddle and the Mic
[DWN] key can be used as the dash paddle.
To activate Mic UP/ DWN key Paddle mode:
2 Press [M.IN] to select “PA”.
• Press and hold Mic [DWN] to send dots or Mic
[UP] to send dashes in CW mode.
4 To exit Mic UP/ DWN key Paddle mode, access
Menu No. 40 and select “PF”.
SWAP DOT AND DASH PADDLE POSITIONS

This function reverses the position of the dot and dash
paddle positions. As a default, the left paddle sends
dots and the right paddle sends dashes. When this
function is ON, the left paddle will send dashes and
the right paddle will send dots.
• The left paddle now sends dashes and the right
paddle now sends dots. To return to the normal
paddle positions, access Menu No. 39 and
select “oFF”.
36
DATA COMMUNICATIONS
RADIO TELETYPE (RTTY) 8 Begin sending data from your computer.
RTTY is the data communications mode with the • Press and hold [PWR (TX MONI)] to monitor
longest history. It was originally designed for use with your signals. Press and hold [PWR (TX MONI)]
mechanical teletypewriters which were often used again to quit this function.
before personal computers became common. Now 9 When finished transmitting, enter a command from
you can easily start operating RTTY with a personal your computer to return to reception mode.
computer and MCP. Unlike Packet, each time you
• The TX-RX LED changes from red (TX) to
type a letter, it is transmitted over the air. What you
green (RX).
type is transmitted and displayed on the computer
screen of the recipient. The following frequencies (measured in kHz) are
commonly used for RTTY operation:
RTTY operation uses frequency shift keying (FSK)
and the 5-bit Baudot code or the 7-bit ASCII code to
IARU Region 1
transmit information. U.S.A./ Canada
(Europe/ Africa)
For cable connections, refer to “RTTY OPERATION” 1800 ~ 1840 1838 ~ 1842
{page 68}.
3605 ~ 3645 (DX: 3590) 3580 ~ 3620
For further information, consult reference books about
Amateur Radio. 7080 ~ 7100 (DX: 7040) 7035 ~ 7045
1 Access Menu No. 44 and select an FSK shift. 10140 ~ 10150 10140 ~ 10150
• FSK shift is the difference in frequencies 14070 ~ 14099.5 14080 ~ 14099.5
between a mark and a space. 18100 ~ 18110 18101 ~ 18109
• The 170 Hz shift (default) is normally used on 21070 ~ 21100 21080 ~ 21120
the Amateur bands for the RTTY.
24920 ~ 24930 22920 ~ 24929
2 Access Menu No. 45 and select a key-down 28070 ~ 28150 28050 ~ 28150
polarity.
• Select “oFF” (default) to transmit a mark when
keying down or “on” to transmit a space. PHASE-SHIFT KEYING 31 BAUD (PSK31)
3 Access Menu No. 46 and select “2125” (high tone) PSK31 is a digital modulation method used in
or “1275” (low tone) for mark. amateur radio communications. You can perform data
• High tone (default) is commonly used communications in real-time using a keyboard, like
nowadays. RTTY. Additionally, because of the narrow bandwidth
4 Select an operating frequency. (31.25 Hz) you can even use PSK31 on congested
frequencies. Another merit to PSK31 is that it can
5 Press [CW/FSK (REV)] to select FSK mode. be enjoyed with a simple antenna and low transmit
• “FSK” appears. power.
Using the sound function of your PC along with
PSK31 software, many amateur radio operators enjoy
PSK31.
• If necessary, access Menu No. 67 to configure • Refer to “TNC AND MCP” {page 69} for
the appropriate audio output level for your connections.
MCP. The audio output level of ANO (ACC2 • When managing PSK31 using the sound capability
connector/ pin 3) changes {page 65}. The AF of a PC, use SSB mode.
control cannot be used to adjust the audio level • Set AGC to fast.
for your MCP.
• Turn off the speech processor.
6 Some stations may be operating in Reverse shift.
• Refer to “EXTERNAL AUDIO SETTINGS”
In this case, press and hold [CW/FSK (REV)] to
{page 58} for Audio Settings.
reverse the shift (the upper sideband is used).
• “FSR” appears. For further information, consult reference books about
Amateur Radio.
• Traditionally, the lower sideband is used for

FSK operation. Press and hold [CW/FSK
(REV)] again to return to the lower sideband.
“FSK” appears.
7 Follow the instructions provided with your MCP
and enter a command from your computer to
transmit.
• The TX-RX LED changes from green (RX) to
red (TX).
37
REJECTING INTERFERENCE
DSP FILTERS ■ CW/ FSK Mode
Kenwood digital signal processing (DSP) technology 1 Select CW or FSK mode.
is adapted to this transceiver. Using DSP filtering 2 Turn the LO/WIDTH control clockwise
(AF), you can control the bandwidth, cancel the to increase the bandwidth (wide), or
multiple jamming beat, and reduce the noise level. counterclockwise to decrease the bandwidth
(narrow).
CHANGING THE DSP FILTER BANDWIDTH
For improving interference reduction capability, this Desired signal
Interfering
transceiver also provides IF filters designed using signal
DSP technology. When in SSB, FM, or AM mode, you Interfering
can change the filter bandwidth by altering its low and/ signal
or high cut-off frequency. For CW, FSK, and DATA
modes, you can change the filter bandwidth by directly
specifying a bandwidth. Changing the filter bandwidth Before After
does not affect the current receive frequency.
• The meter display changes, based on the Mode Bandwidth Selection (Hz) Default
bandwidth you are setting up.
50, 80, 100, 150, 200, 250,
CW 300, 400, 500, 600, 1000, 500 Hz
1500, 2000, 2500
FSK 250, 500, 1000, 1500 500 Hz
3 As for CW, you can further adjust the shift
frequency for the pass band. Turn the
HI/SHIFT control clockwise to increase the
■ SSB/ FM/ AM Mode shift frequency (high), or counterclockwise to
1 Select SSB, FM, or AM mode. decrease the shift frequency (low).
2 Turn the LO/WIDTH control clockwise to raise Shift Frequency (Hz) Default
the low cut-off frequency, or counterclockwise
to lower the low cut-off frequency. 300, 350, 400, 450, 500, 550, 600,
650, 700, 750, 800, 850, 900, 950, 800 Hz
1000
Mode Low cut Frequency (Hz) Default
SSB/ 0, 50, 100, 200, 300, 400, ■ Data Mode
300 Hz
FM 500, 600, 700, 800, 900, 1000
1 Select Data mode (USB-DATA/LSB-DATA).
AM 0, 100, 200, 300 100 Hz
2 Turn the LO/WIDTH control clockwise
Turn the HI/SHIFT control clockwise to raise the to increase the bandwidth (wide), or
high cut-off frequency, or counterclockwise to counterclockwise to decrease the bandwidth
lower the high cut-off frequency. (narrow).
Mode High cut Frequency (Hz) Default Bandwidth Selection (Hz) Default
1000, 1200, 1400, 1600, 50, 80, 100, 150, 200, 250, 300, 400,
2500 Hz
SSB/ 1800, 2000, 2200, 2400, 500, 600, 1000, 1500, 2000, 2500
2600 Hz
FM 2600, 2800, 3000, 3400,
4000, 5000 3 Turn the HI/SHIFT control clockwise to increase
the shift frequency (high), or counterclockwise
AM 2500, 3000, 4000, 5000 5000 Hz to decrease the shift frequency (low).
Low cut-off frequency
Shift Frequency (Hz) Default
High cut-off frequency
1000, 1100, 1200, 1300, 1400, 1500,
1600, 1700, 1800, 1900, 2000, 2100, 1500 Hz
Desired signal 2210
Interfering Interfering
signal signal
■ IF Filter A and B
This transceiver has 2 built-in IF filters: A and
B. The IF Filter settings are stored with the last
0 Hz 1 KHz 5 KHz settings of the LO/WIDTH and HI/SHIFT controls.
Note: The cut-off frequencies can be adjusted Press [IF FIL] to toggle between IF Filter setting A
independently for each operating mode. When you change
the operating mode, the previous setting is recalled for each and B.
operating mode.
• “ ” appears when IF filter setting A is selected
and “ ” appears when IF filter setting B is
selected.
38
9 REJECTING INTERFERENCE
Press and hold [IF FIL] to momentarily display each ■ Notch Filter Bandwidth
setting value of the DSP filter band as follows: Press and hold [NOTCH (WIDE)] to toggle the
SSB/ AM/ FM mode: Notch filter bandwidth between NORMAL and
High cut Frequency > Low cut Frequency WIDE.
CW/ SSB data mode: • “ ” appears when the Notch filter
Shift Frequency > Bandwidth bandwidth is set to WIDE.
FSK mode: Bandwidth only
BEAT CANCEL (SSB/ AM)
AUTO NOTCH FILTER (SSB) Two types of Beat Cancel DSP filters are available.
Beat Cancel 1 (BC1) is effective for removing a weak
The Auto Notch filter automatically locates and beat or continuous beat signals. Beat Cancel 2 (BC2)
attenuates any single interfering tone within the is effective for removing intermittent beat signals, such
receive pass band. This function operates digitally as CW signals.
at the IF filter level, hence it can affect your S-meter
reading and may also affect (slightly attenuate) your Filter pass band (AF)
Interfering
desired signal. However, controlling the AGC level by tones
notching out the strong interfering beat signals could
bring up the desired SSB signal that is covered by the
interfering beat signal. If the interfering tone is weak, Desired
you may find that Beat Cancel eliminates them more signal
effectively.
Before After
Receive pass band
Interfering
tones Press [BC (A.NOTCH)] to cycle through Beat Cancel
1, Beat Cancel 2, and OFF.
• “ ” or “ ” appears when the Beat Cancel
Desired function is ON.
signal
• The interfering beat signals are removed.
Before After
NOISE REDUCTION (ALL MODES)
Press and hold [BC (A.NOTCH)] to toggle the Auto
Notch Filter ON and OFF. This transceiver provides 2 types of Noise Reduction
functions (NR1 and NR2) for reducing random noise
• “ ” appears when this function is ON. which interferes with the desired signal.
• The interfering beat signals are notched out. NR1 differs, depending on the reception mode.
When receiving a voice call in SSB/ FM/ AM mode,
■ Auto Notch Tracking Speed noise reduction uses a spectrum subtraction system.
If the interfering beat signals change the tone When receiving a non-voice call in CW/ FSK mode,
frequency randomly, you can adjust the Auto Notch noise reduction uses a LMS adaptive filter which
tracking speed. emphasizes the periodic signal.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or NR2 uses a SPAC format, which extracts a periodic
turn the MULTI/CH control to select Menu No. signal from within the received signal.
24 Press [NR (LEV)] to cycle between NR1, NR2, and
2 Press [M.IN]/ [SCAN (SG.SEL)] to select the OFF.
level from FIX (0), and 1 to 4. • “ ” or “ ” appears, depending on which
• Level 1 is the slowest beat tone tracking noise reduction filter is selected.
speed and Level 4 is the fastest. FIX
terminates the beat tone tracking. Adjust
this parameter manually to remove the beat
signal if necessary.
MANUAL NOTCH FILTER (SSB/ CW/ FSK)

Use manual notch when you want to vary the width of
the notch while verifying the interfering signal.
1 Press [NOTCH (WIDE)] to toggle the Manual
Notch Filter ON and OFF.
• “ ” appears when this function is ON.
2 Turn the NOTCH control to adjust to the point
where beat noise just disappears.
39
9 REJECTING INTERFERENCE
■ Setting the NR1 Level Adjustment PRE-AMPLIFIER

NR1 uses an adaptive filter to reduce the noise Switching the pre-amplifier OFF may help reduce
element from the received signals. When the S/N interference from adjacent frequencies.
ratio is reasonably good in SSB, using NR1 will
improve the S/N further. Press [PRE (ANT 1/2)] to toggle the pre-amplifier ON
and OFF.
While NR1 is ON, you can further adjust the noise
• “ ” appears when this function is ON.
reduction level by pressing and holding [NR (LEV)],
then turning the MULTI/CH control to select the The ON/ OFF setting will be automatically stored in
level from 1 to 10. The default is 5. The level is the current band. Each time you select the same
saved separately for SSB/FM/AM and CW/FSK. band, the same setting will be automatically selected
The frequency range of each band is provided in the
■ Setting the NR2 Time Constant table below (under “ATTENUATOR”).
You can change the correlation time for NR2
(SPAC). When in SSB mode, select the correlation
time that allows you to hear signals with clarity. ATTENUATOR
When receiving CW, it is best to select the longest The Attenuator reduces the level of received
correlation time that allows reliable reception. The signals. This function is useful when there is strong
longer the correlation time, the better the S/N ratio. interference from adjacent frequencies.
When NR2 is ON, press and hold [NR (LEV)], then Press [ATT (RX ANT)] to toggle the attenuator ON
turn the MULTI/CH control to select the correlation and OFF.
time from 2 to 20 ms. The default is 20 ms. • “ ” appears when this function is ON.
Note:
◆ When using Noise Reduction 1 in SSB, FM, or AM
The ON/ OFF setting will be automatically stored
mode, the beat signal is suppressed along with the in the current band. Each time you select the
normal signal. This is not a malfunction. same frequency band, the attenuator setting will be
◆ Using Noise Reduction 2 in SSB mode may lower the automatically recalled. The frequency range of each
clarity of signals or induce pulse noise, depending on the band is shown below.
conditions.
Frequency Pre-amplifier Attenuator
Band (MHz) (Default) (Default)
NOISE BLANKER 0.03 ~ 0.522 OFF OFF
The Noise Blanker is designed to reduce pulse noise
such as that generated by automobile ignitions. The 0.522 ~ 2.5 OFF OFF
Noise Blanker does not function in FM mode. 2.5 ~ 4.1 OFF OFF
• NB1 performs blanking through an analog circuit. 4.1 ~ 6.9 OFF OFF
NB2 performs blanking using DSP.
6.9 ~ 7.5 OFF OFF
Press [NB (LEV)] to cycle between Noise Blanker 1,
Noise Blanker 2, and OFF. 7.5 ~ 10.5 ON OFF
• “ ” or “ ” appears, depending on which 10.5 ~ 14.5 ON OFF
Noise Blanker is selected. 14.5 ~ 18.5 ON OFF
You can further adjust the Noise Blanker level from 18.5 ~ 21.5 ON OFF
1 to 10. The default level is 6. Press and hold [NB
(LEV)], then turn the MULTI/CH control to adjust the 21.5 ~ 25.5 ON OFF
Noise Blanker level. 25.5 ~ 30.0 ON OFF
• “NB LV.” and the current level appear on the 30.0 ~ 60.0 ON OFF
sub-display.
Note:
◆ The Noise Blanker is available only for SSB, CW, FSK, and
AM modes. CW REVERSE (RECEPTION)
◆ Increasing the Noise Blanker level degrades the This function pivots the BFO from the default position
intermodulation characteristics of the transceiver.
(USB) to another position (LSB) in CW mode. It is
◆ For effective Noise Blanker operation, experiment with both
NB1 and NB2 on each band.
sometimes effective to remove the interfering signals
◆ When using Noise Blanker 2 and a CW signal is received,
from the IF passband by pivoting the BFO.
there are times when the received signal may be distorted. 1 Press [CW/FSK (REV)] until “CW” appears.
This is not a malfunction.
2 Press and hold [CW/FSK (REV)].
• “CW” changes to “CWR”.
3 To recover the default BFO position, press and
hold [CW/FSK (REV)] again.
• “CWR” changes to “CW”.
40
MEMORY FEATURES
MEMORY CHANNELS
This transceiver provides you with 110 memory
channels, numbered 00 to 99 and P0 to P9, for
storing operating frequency data, modes, and other • To exit Memory Scroll mode and abort the
information. Memory channels 00 to 99 are called storage process, press [CLR].
Conventional Memory Channels. Memory channels
P0 to P9 are designed for programming VFO tuning 4 Turn the MULTI/CH control, or press Mic [UP]/
ranges and scan ranges. The data you can store is [DWN] to select a memory channel.
listed below. • You can also select a channel by entering
a 2-digit number, such as 12, using the
Conventional memory channels are used for storing
numeric keys. Press [1.8 (1)], [3.5 (2)] for
data you will often recall. For example, you may store
example.
the frequency where you regularly meet your club
members.
Channel Channel
Parameter
00 ~ 99 P0 ~ P9
5 Press [M.IN] again to store the data.
RX Frequency Yes Yes1 • The previous data stored in the channel is
TX Frequency Yes (simplex) overwritten.
Mode for RX Yes Yes1
(simplex) ■ Split-Frequency Channels
Mode for TX Yes
Programmable VFO
No Yes • “ ” or “ ” appears to show which VFO
Start/ End Frequencies
is selected.
Tone Frequency Yes Yes
CTCSS Frequency Yes Yes 2 Select the frequency, mode, etc., to be stored.
• This frequency and mode will be used for
Tone/ CTCSS ON/ OFF
Yes Yes transmitting.
Status
Memory Name Yes Yes 3 Press [A/B (A=B)] to select the other VFO.
Memory Channel Lockout 4 Select the reception frequency and mode.
Yes1 Yes1
ON/ OFF 5 Press [SPLIT].
1 Changing the data after recalling a memory channel overwrites • “ ” appears.
the contents of the channel.
STORING DATA IN MEMORY

There are 2 methods used for storing transmission/
reception frequencies and associated data in memory 6 Press [M.IN] to enter Memory Scroll mode.
channels 00 to 99. Use either method, depending
on the relationship of the reception and transmission
frequencies you store:
• Simplex channels: • To exit Memory Scroll mode and abort the
RX frequency = TX frequency storage process, press [CLR].
• Split-frequency channels: 7 Turn the MULTI/CH control, or press Mic [UP]/
RX frequency ≠ TX frequency [DWN] to select a memory channel.
Memory channels P0 to P9 can also be used as • You can also select a channel by entering
simplex channels. a 2-digit number, such as 12, using the
Note: When RIT or XIT is ON, the frequency that includes the numeric keys. Press [1.8 (1)], [3.5 (2)] for
RIT or XIT offset will be stored. example.
■ Simplex Channels
• “ ” or “ ” appears to show which VFO 8 Press [M.IN] to store the data.
is selected.
• The previous data stored in the channel is
2 Select the frequency, mode, etc., to be stored. overwritten.
3 Press [M.IN] to enter Memory Scroll mode. Note: When subtone frequencies differ between TX and RX
while performing memory-VFO split operation, the subtone
• “ ” appears. frequency for TX will be stored in the memory channel.
41
10 MEMORY FEATURES
MEMORY RECALL AND SCROLL ■ Temporary Frequency Changes

There are 2 modes which allow you to retrieve After retrieving frequencies and associated data in
frequencies and associated data that you stored in a Memory Recall mode, you can temporarily change
memory channel: Memory Recall and Memory Scroll. the data without overwriting the contents of the
memory channel.
■ Memory Recall 1 Access Menu No. 18 and select “on”.
In this mode, the transceiver receives and • Skip this step when changing only the
transmits using a frequency that you retrieve. associated data (not the frequency).
You can temporarily change the frequency and
associated data without overwriting the contents 2 Recall a memory channel.
of the memory channel when Menu No. 18 is ON 3 Change the frequencies and associated data.
(default is OFF).
• Use only the Tuning control to select a
1 Press [M/V] to enter Memory Recall mode. frequency.
• The memory channel that was last selected 4 If necessary, for future use, store the changed
appears. data in another memory channel. Refer to
“Channel ➡ Channel Transfer” {below}.
Note: If Menu No. 18 is set to “on”, the frequency of the
memory channel can be changed.
2 Turn the MULTI/CH control, or press Mic [UP]/ MEMORY TRANSFER

[DWN] to select a memory channel.
• Continuously holding down Mic [UP]/ [DWN] ■ Memory ➡ VFO Transfer
steps the transceiver through the memory
channels until the key is released. After retrieving frequencies and associated data
from Memory Recall mode, you can copy the data
• Memory channels which contain no data are to the VFO. This function is useful, for example,
skipped. when the frequency you want to monitor is near the
• You cannot change memory channels while frequency stored in a memory channel.
transmitting. 1 Recall the desired memory channel.
3 To exit Memory Recall mode, press [M/V]. 2 Press [M>V].
Note: If Menu No. 18 is set to “on”, the frequency of the
memory channel can be changed. • When a simplex channel is recalled, the data
is copied to VFO A or VFO B, depending on
■ Memory Scroll which VFO was used to recall the channel.
• When a split channel is recalled, the RX
Use this mode to check the contents of the data is copied to VFO A and the TX data is
memory channels without changing the current copied to VFO B.
reception frequency. In this mode, frequencies you
retrieve are not used for receiving and transmitting. Note: Pressing [M>V] after temporarily changing the
retrieved data copies the new data to the VFO.
1 Press [M.IN] to enter Memory Scroll mode.
• The memory channel that was last selected ■ Channel ➡ Channel Transfer
appears. You can also copy channel information from one
memory channel to another. This function is useful
when storing frequencies and associated data that
you temporarily change in Memory Recall mode.
2 Turn the MULTI/CH control, or press Mic [UP]/ 1 Recall the desired memory channel.
[DWN] to step through the memory channels. 2 Press [M.IN] to enter Memory Scroll mode.
• You can also change channels by entering • To exit Memory Scroll mode, press [CLR].
a 2-digit number. Press [24 (8)], [28 (9)] for
example. 3 Select the memory channel where you would
like the data copied, using the MULTI/CH
3 To exit Memory Scroll mode, press [CLR]. control.
• The transceiver re-displays the memory 4 Press [M.IN].
channel or VFO frequency that was selected
before you activated Memory Scroll.
Note: Do not press [M.IN] again after entering Memory
Scroll mode. Pressing [M.IN] results in over-writing the
current VFO data to the memory channel you selected.
42
10 MEMORY FEATURES
Channel 00 ~ 99 ➡ Channel 00 ~ 99 Channel P0 ~ P9 ➡ Channel P0 ~ P9

RX frequency ➡ RX frequency TX/RX frequency ➡ TX/RX frequency
TX frequency ➡ TX frequency Start frequency ➡ Start frequency
Mode for RX ➡ Mode for RX End frequency ➡ End frequency
Mode for TX ➡ Mode for TX Mode for TX/RX ➡ Mode for TX/RX
Tone frequency ➡ Tone frequency Tone frequency ➡ Tone frequency
CTCSS frequency ➡ CTCSS frequency CTCSS frequency ➡ CTCSS frequency
Tone/ CTCSS Tone/ CTCSS Tone/ CTCSS/ Cross Tone/ CTCSS/ Cross
➡ ➡
ON/ OFF status ON/ OFF status tone ON/ OFF status tone ON/ OFF status
Memory Name ➡ Memory Name Memory Name ➡ Memory Name
Memory Channel Memory Channel Memory Channel Memory Channel
➡ ➡
Lockout ON/ OFF Lockout OFF Lockout ON/ OFF Lockout OFF
Channel 00 ~ 99 ➡ Channel P0 ~ P9 Note: After copying, the Memory Channel Lockout turns OFF.
➡ TX/RX frequency
STORING FREQUENCY RANGES
RX frequency ➡ Start frequency
Memory channels P0 to P9 allow you to store
➡ End frequency frequency ranges for VFO tuning and Program Scan.
Mode for RX ➡ Mode for TX/RX Program Scan is described in the next chapter. To
tune or scan frequencies within a specified range,
TX frequency ➡ ––
store the start and end frequencies for that range in
Mode for TX ➡ –– advance.
Tone frequency ➡ Tone frequency 1 Press [A/B (A=B)] to select VFO A or VFO B.
CTCSS frequency ➡ CTCSS frequency 2 Select the desired start frequency.
Tone/ CTCSS/ Cross Tone/ CTCSS/ Cross 3 Press [M.IN] to enter Memory Scroll mode.
➡
tone ON/ OFF status tone ON/ OFF status
• To exit Memory Scroll mode and abort the
Memory Name ➡ Memory Name storage process, press [CLR].
Memory Channel Memory Channel 4 Turn the MULTI/CH control, or press Mic [UP]/
➡
Lockout ON/ OFF Lockout OFF [DWN] to select a memory channel in the range of
P0 to P9.
Channel P0 ~ P9 ➡ Channel 00 ~ 99
➡ RX frequency
TX/RX frequency
➡ TX frequency
➡ Mode for RX 5 Press [M.IN] to store the start frequency in the
Mode for TX/RX memory channel.
➡ Mode for TX
• “ENDINPUT” appears on the sub-display.
Start frequency ➡ ––
End frequency ➡ ––
Tone frequency ➡ Tone frequency
CTCSS frequency ➡ CTCSS frequency 6 Turn the Tuning control or MULTI/CH control to
Tone/ CTCSS/ Cross Tone/ CTCSS/ Cross select the end frequency.
➡
tone ON/ OFF status tone ON/ OFF status 7 Press [M.IN] to store the end frequency in the
Memory Name ➡ Memory Name memory channel.
Memory Channel Memory Channel • The previous data stored in the channel is
➡ overwritten.
Lockout ON/ OFF Lockout OFF
43
10 MEMORY FEATURES
■ Confirming Start/ End Frequencies ERASING MEMORY CHANNELS

Use this procedure to check the start and end If there are memory channels that you will not recall
frequencies that you stored in channels P0 to P9. in the future, you may prefer erasing the contents of
1 Press [M/V] to enter Memory Recall mode. those channels.
2 Turn the MULTI/CH control or press Mic [UP]/ 1 Press [M/V] to enter Memory Recall mode.
[DWN] to select a memory channel from P0 to 2 Turn the MULTI/CH control or press Mic [UP]/
P9. [DWN] to select the desired memory channel.
3 Press [A/B (A=B)] to check the start frequency, • You can also select a channel by entering a
then press [A/B (A=B)] again to check the end 2-digit number. Press [ENT], [7 (3)], [10 (4)]
frequency. for example.
3 Press and hold [CLR].
■ Programmable VFO
• A long beep sounds to confirm that the channel
Using the start and end frequencies that you stored data has been erased.
in channels P0 to P9, Programmable VFO restricts
the frequency range that you can tune with the MEMORY CHANNEL NAME
Tuning control. One application of this function is
to help you operate within the authorized frequency You can assign a name to each memory channel, with
limits of your license. a maximum of 8 alpha-numeric characters.
1 Press [M/V] to enter Memory Recall mode. Note: You cannot name the Quick Memory channels.
2 Turn the MULTI/CH control or press Mic [UP]/ 1 Press [M/V] to enter Memory Recall mode.
[DWN] to select a memory channel from P0 to 2 Turn the MULTI/CH control or press Mic [UP]/
P9. [DWN] to select a memory channel.
You can now only tune from the start frequency to 3 Press [Q-MR].
the end frequency, using the Tuning control.
4 Turn the MULTI/CH control or press [M.IN]/ [SCAN
Note: Pressing Mic [UP]/ [DWN] or turning the MULTI/CH
control changes the memory channel number while in (SG.SEL)] to select the desired alpha-numeric
Programmable VFO mode. character. You can move the cursor to the left
by pressing [Q-M.IN], or to the right by pressing
MEMORY CHANNEL LOCKOUT [Q-MR]. Press [CL] to erase the character at the
cursor.
You can lock out memory channels that you prefer
not to monitor during Memory Scan. Memory Scan is 5 After selecting all the necessary characters for the
described in the next chapter {page 48}. memory channel name, press [MENU] to store the
name.
1 Press [M/V] to enter Memory Recall mode.
6 When you recall a memory channel with a name,
2 Turn the MULTI/CH control or press Mic [UP]/ the name is displayed on the sub-display along
[DWN] to select the desired memory channel. with the memory channel number.
3 Press [CLR].
• Do not hold down the [CLR] key. Holding
[CLR] for more than approximately 2 seconds QUICK MEMORY
will erase the contents of the memory channel. Quick Memory is designed to quickly and temporarily
• A dot appears beside the right-most digit of save data without specifying a particular memory
the memory channel number to indicate the channel. Use Quick Memory to store data you will not
channel has been locked out. use in future operating sessions. For example, as you
tune across the band looking for DX, it is convenient
to store stations that you want to contact. You can
quickly jump between several different memory
channels as you monitor them.
• Repeatedly pressing [CLR] toggles between
Quick Memory channels can store the following data:
adding and removing the channel from the scan
list.
VFO A frequency and VFO B frequency and
operating mode operating mode
RIT ON/ OFF XIT ON/ OFF
RIT/ XIT offset frequency FINE ON/ OFF
Noise Blanker ON/ OFF DSP Beat Cancel
OFF/ 1/ 2
DSP Noise Reduction IF Notch
OFF/ 1/ 2
DSP filter bandwidth Simplex/ Split
44
10 MEMORY FEATURES
NUMBER OF QUICK MEMORY CHANNELS RECALLING QUICK MEMORY CHANNELS

This transceiver provides up to 10 Quick Memory You can recall a Quick Memory channel only when
channels. You can adjust the number of available you operate the transceiver in VFO mode.
channels by accessing Menu No. 17 and selecting “3”,
1 Press [Q-MR].
“5” (default), or “10”.
• The current memory channel number appears.
STORING INTO QUICK MEMORY • If there is no data stored in any Quick Memory
channel, the data cannot be recalled to the
Each time you store a new frequency, all previously
current VFO; an error beep sounds.
stored frequencies are bumped to the next respective
Quick Memory channel. When all 10 memory 2 Turn the MULTI/CH control to select a Quick
channels contain frequencies, storing one more Memory channel.
frequency bumps the contents of memory channel 9 • You cannot change memory channels while
off the stack (the data is lost). transmitting.
The following diagram illustrates how the Quick 3 To exit, press [Q-MR] again.
Memory stacks the data in memory each time you
press [Q-M.IN]. Note: Memory channels cannot be changed while using the
TF-SET function.
New data
24.911 14.005 14.235 14.250 18.111
Memory 0 Memory 1 Memory 2 Memory 3 Memory 4 TEMPORARY FREQUENCY CHANGES
50.015 7.082 29.610 3.545 14.195 After recalling a Quick Memory channel, you can
temporarily change the data without overwriting
Memory 5 Memory 6 Memory 7 Memory 8 Memory 9
the contents of the channel. You can change the
New data frequency even when you select “oFF” in Menu
21.005 24.911 14.005 14.235 14.250 No. 18.
Memory 0 Memory 1 Memory 2 Memory 3 Memory 4 1 Press [Q-MR].
18.111 50.015 7.082 29.610 3.545 2 Turn the MULTI/CH control to select a Quick
Memory 5 Memory 6 Memory 7 Memory 8 Memory 9 Memory channel.
New data 3 Change the frequencies and associated data.
14.085 21.005 24.911 14.005 14.235
4 To store the changed data in the Quick Memory,
Memory 0 Memory 1 Memory 2 Memory 3 Memory 4
press [Q-M.IN].
14.250 18.111 50.015 7.082 29.610 • This action stores the new data in the current
Memory 5 Memory 6 Memory 7 Memory 8 Memory 9 channel and bumps the old frequency to the
next higher Quick Memory channel.
You can store data in the Quick Memory only when
5 To exit, press [Q-MR] again.
you operate the transceiver in VFO mode.
Note: Memory channel data can also be changed while using
1 Select the frequency, mode, etc., on the the TF-SET function.
transceiver VFO.
2 Press [Q-M.IN].
QUICK MEMORY ➡ VFO TRANSFER
• Each time you press [Q-M.IN], the current VFO
data is written to the Quick Memory. This function copies the contents of the recalled
memory channel to the VFO.
Note: When RIT or XIT is ON, the ON status and the offset will
also be stored. 1 Recall a Quick Memory channel.
2 Press [M>V].
Note: Pressing [M>V] after temporarily changing the recalled
data copies the new data to the VFO.
ERASING QUICK MEMORY CHANNELS

1 Recall a Quick Memory channel.
2 Press and hold [CLR].
• A confirmation message appears on the
display.
3 Press [CLR].
• The channel data has been erased.
45
SCAN
Scan is a useful function for hands-off monitoring of If one or more Program Scan frequency ranges are
your favorite frequencies. By becoming comfortable programmed in VGROUP–0 to 9 (Memory channel
with all types of Scan, you will increase your operating numbers P0 ~ P9 in other words):
efficiency.
1 Press and hold [SCAN (SG.SEL)] in VFO mode.
This transceiver provides the following types of scans: • “VGROUP–n” appears on the sub-display
(where n represents a number from 0 to 9).
Scan Type Purpose
Scans the entire frequency 2 Turn the MULTI/CH control to select the Program
VFO Scan Scan memory (VGROUP–0 to VGROUP–9). As
range of the transceiver.
Normal you select the channel, “on” or “oFF” appears
Scan Scans the specific frequency on the frequency display. “on” signifies that the
Program
ranges stored in Memory selected VGROUP is active for the Program Scan
Scan
channels P0 ~ P9. and “oFF” signifies that the selected VGROUP is
All-Channel Scans all Memory channels, inactive for the Program Scan.
Memory Scan from 00 ~ 99 and P0 ~ P9
Scan Scans the specific Memory
Group Scan
channel groups.
Scans the Quick Memory Configure all P.SCAN channels (VGROUP–0 ~
Quick Memory Scan
channels. VGROUP–9) as “oFF” by pressing [SCAN (SG.
SEL)].
Note:
◆ While using CTCSS in FM mode, Scan stops only for the
signals that contain the same CTCSS tone that you selected.
◆ Pressing Mic [PTT] causes Scan to stop.
3 Press and hold [SCAN (SG.SEL)] or press [CLR]
to return to the current VFO mode.
NORMAL SCAN 4 Press [SCAN (SG.SEL)] to start the VFO Scan.
While operating the transceiver in VFO mode, 2 types 5 Press [SCAN (SG.SEL)] or [CLR] to stop the VFO
of scanning are available. Scan.
• VFO Scan Note:
◆ While scanning, you can change the scan speed by
The transceiver scans the entire frequency turning the RIT/ XIT control. Turn the control clockwise/
range of the transceiver. For example, if you are counterclockwise to decrease/ increase the scan speed.
operating and receiving on the transceiver’s The speed indicator appears on the sub-display, where P1 is
VFO A at 14.195.00 MHz, it scans all the the fastest speed and P9 is the slowest.
frequencies in the range of 30.00 kHz to ◆ You cannot change the VFO Scan speed in FM mode.
59.999.99 MHz. (Refer to the available VFO
frequency range in the specifications.)
PROGRAM SCAN
• Program Scan
Program Scan monitors the range between the
By programming the start and end frequency start and end frequencies that you have stored in
in Memory channels P0 ~ P9, you can limit the Memory channels P0 ~ P9 (VGROUP–0 ~ 9). Refer
scanning frequency range. Since there are to “STORING FREQUENCY RANGES” {page 43} for
10 memory channels (P0 ~ P9) available for details on how to store the start and end frequencies
specifying the start and end frequencies, you can to these Memory channels.
select 1 or more (a maximum of 10) ranges to
scan. This is useful when you are waiting for a DX You can select a maximum of 10 memory channels
station on a certain frequency but the station may (VGROUP–0 to 9) and sequentially scan the
appear on a slightly higher or lower frequency. frequency ranges that you stored in these channels.
If the current VFO frequency falls within the selected
VGROUP frequency range, Program Scan starts from
the VGROUP number and then continues to scan
VFO SCAN the next larger VGROUP number. If the current VFO
VFO Scan scans the entire frequency range that is frequency is outside all of the VGROUP frequency
available for the current VFO. When the Program ranges, Program Scan starts from the smallest
Scan frequency range is not programmed or no VGROUP number that is selected as “on” (each
Scan Group is selected for the Program Scan, the VGROUP can be set to either “on” or “oFF”).
transceiver also scans the entire frequency range Note: At least one of the valid Program Scan channels (from P0
available for the current VFO. to P9) must be programmed and selected to perform Program
Scan. If no P.SCAN (memory channel P0 ~ P9) is selected for
The memory channel numbers P0 ~ P9 have alias Program Scan, the transceiver performs VFO Scan {above}.
names, “VGROUP”. “VGROUP–0” represents 1 Press [A/B (A=B)] to select VFO A or VFO B.
channel P0, “VGROUP–1” represents channel P1,
“VGROUP–2” represents channel P2, and so on up to 2 Press and hold [SCAN (SG.SEL)].
“VGROUP–9” which represents channel P9.
46
11 SCAN
PROGRAM SCAN PARTIALLY SLOWED

You can specify a maximum of 5 frequency points for
each memory channel from P0 to P9 so that Program
3 Turn the MULTI/CH control or press Mic [UP]/ Scan slows down the scanning speed. To specify the
[DWN] to select the memory channel (VGROUP–0 slow down frequency points, first program the start
to VGROUP–9). As you select the Memory and end frequencies into a memory channel (P0 ~ P9).
Channel, “on” or “oFF” appears on the main 1 Access Menu No. 19 to confirm that the function is
frequency display. “on” signifies that the memory ON (default is ON).
channel is active for the Program Scan and “oFF”
signifies that the memory channel group is inactive 2 You can further configure the slow down frequency
for the Program Scan. width. Access Menu No. 20 to select the range
from 100 Hz to 500 Hz (default is 300 Hz).
4 To activate the Program Scan frequency range, Note: If you select, for example, 500 Hz for Menu No. 20,
select the desired VGROUP number by turning the the Program Scan slows down to a ±500 Hz width, centering
MULTI/CH control. Then, press [M.IN] to select the frequency you marked below.
“on” for the VGROUP (channel). When a channel
3 Press [M/V], then turn the MULTI/CH control to
is activated for Program Scan, “on” appears on the
recall the memory channel (P0 ~ P9) for which you
display.
want to specify the scan slow down frequencies.
4 Turn the Tuning control to the center frequency
point that you want the Program Scan to slow
down. Then, press [Q-M.IN] to mark the slow
5 Press and hold [SCAN (SG.SEL)] or press [CLR] down frequency point.
to return to the current VFO mode. • “ ” appears.
6 Press [SCAN (SG.SEL)] to start the Program 5 Repeat step 4 to specify the center slow down
Scan. frequency points.
• To quickly move toward a desired frequency • You can specify a maximum of 5 frequency
while scanning, turn the Tuning control or the points for each channel.
MULTI/CH control, or press Mic [UP]/ [DWN].
6 If you want to clear a slow down frequency point
• Turning the RIT/ XIT control clockwise that you previously stored, select the frequency
decreases the scan speed and that you stored, then press [Q-M.IN] at this
counterclockwise increases the speed, except frequency spot where “ ” appears.
while in FM mode. The current scan speed is
shown on the display; P1 is the fastest speed • A confirmation beep sounds and “ ”
and P9 is the slowest. disappears.
• While in FM mode, Scan automatically stops • To clear all slow down frequency points, press
on a frequency where a signal is present. The and hold [Q-M.IN].
transceiver will either remain on that channel 7 Press [M/V] to return to VFO mode.
for a short time (Time-Operated mode) or until
the signal drops out (Carrier-Operated mode), 8 Press [SCAN (SG.SEL)] to start the Program Scan
depending on which mode you select via Menu with the slow down frequency point(s).
No. 22 {page 48}. Note:
◆ During Program Scan, you can turn the RIT/ XIT control
7 To stop Scan, press [SCAN (SG.SEL)] or [CLR]. to adjust the scanning speed. Turn the control clockwise/
Note: counterclockwise to slow down/ speed up the scan. The
Program Scan speed indicator appears on the main display
◆ If you have turned the SQL control clockwise, far beyond the during Program Scan; P1 is the fastest speed and P9 is the
squelch threshold while in FM mode, Scan may fail to stop slowest.
at a channel where a signal is present. If this happens, turn
the SQL control slightly counterclockwise. ◆ You cannot change the Program Scan speed in FM mode.
◆ If you press [SCAN (SG.SEL)] before storing any frequency ◆ Although you can specify the Program Scan slow down
range for memory channels P0 to P9, the transceiver starts frequency point in FM mode, it does not function.
VFO scan. ◆ When copying a Program Memory Channel, all frequency
◆ When the current receive frequency is within one of the points are cleared.
ranges that you selected with channel numbers, Scan starts
with the current frequency. The operating mode stored in
the memory channel is used.
◆ The operating mode can be changed while scanning, but the
memory channel will be overwritten with the changed mode.
◆ When the current Scan range is smaller than a single step of
the MULTI/CH control, turning the control clockwise causes
Scan to jump to the start frequency, and counterclockwise to
the end frequency.
◆ Starting Program Scan switches OFF the RIT and XIT
functions.
◆ While in FM mode, Program Scan monitors rounded off
frequencies regardless of the Menu No. 12 setting.
47
11 SCAN
SCAN HOLD ALL-CHANNEL SCAN

This function stops Program Scan for approximately Use the following procedure to scan all the memory
5 seconds, then resumes Scan when you jump to the channels that contain frequency data in sequence,
desired frequency by turning the Tuning control or the ignoring the Memory Group number.
MULTI/CH control, or by pressing Mic [UP]/ [DWN].
1 Select Time-Operated or Carrier-Operated mode
To use this function, access Menu No. 21, and select via Menu No. 22.
“on”. The default is OFF.
3 Turn the SQL control to adjust the squelch
MEMORY SCAN threshold to mute the speaker.
Memory Scan monitors all memory channels in which 4 Press and hold [SCAN (SG.SEL)] to enter Scan
you have stored frequencies (All-channel Scan) or only Group Select mode.
a desired group of memory channels (Group Scan). • Turn the MULTI/CH control to select the
Scan automatically stops at a channel where a signal Memory channel group.
is present, regardless of the operating mode. The • MGROUP–0 represents Memory channels
transceiver will either remain on that channel for a 0 ~ 9, MGROUP–1 represents Memory
short time (Time-Operated mode) or until the signal channels 10 ~ 19 and so on up to MGROUP–9
drops out (Carrier-Operated mode). Use Menu No. which represents Memory channels 90 ~ 99
22 to select the mode. The default is “to” (Time- and MGROUP–P which represents Memory
Operated). channels P0 ~ P9.
5 As you select the Memory Groups using the
SCAN RESUME MULTI/CH control, press [M.IN] to select “on” for
The transceiver stops scanning at the frequency all Memory Groups.
(or memory channel) where a signal is detected. It 6 Press and hold [SCAN (SG.SEL)] to return to
then continues scanning according to which resume Memory Recall mode.
mode you have selected. You can choose one of the
following modes. The default is Time-Operated mode. 7 Press [SCAN (SG.SEL)] to start All-channel Scan.
• Time-Operated mode (“to”) • Scan starts from the current memory channel
and ascends up through the channel numbers.
The transceiver remains on a busy frequency (or (The scan direction cannot be changed.)
memory channel) for approximately 6 seconds,
then continues to scan, even if the signal is still • To jump to a desired channel while scanning,
present. turn the MULTI/CH control, or press Mic [UP]/
[DWN].
• Carrier-Operated mode (“co”)
8 To stop Scan, press [SCAN (SG.SEL)] or [CLR].
The transceiver remains on the busy frequency (or Note:
memory channel) until the signal drops out. There
◆ If you have turned the SQL control clockwise, far beyond the
is a 2 second delay between signal dropout and squelch threshold, Scan may fail to stop at a channel where
scan resumption. a signal is present. If this happens, turn the SQL control
slightly counterclockwise.
◆ Starting Memory Scan switches OFF the RIT and XIT
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or functions.
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “to”
(Time-Operated) or “co” (Carrier-Operated).

You can lock out the memory channels that you
prefer not to monitor while scanning (refer to “Memory
Channel Lockout”).
48
11 SCAN
GROUP SCAN ■ Performing Group Scan

110 memory channels are divided into 11 groups Group Scan starts with the smallest group number
so that you can select one or more groups to be and repeats the sequence. For example, if you
scanned, depending on the situation. selected “on” for MGROUP–3, MGROUP–5, and
MGROUP–7, the transceiver scans the channels
■ Memory Group in MGROUP–3 > MGROUP–5 > MGROUP–7 >
MGROUP–3 and so on.
When you store frequency data in a memory
channel, the memory channel belongs to one of 11 1 Select Time-Operated or Carrier-Operated
groups as shown below. mode via Menu No. 22.
MGROUP-0 Memory Channel Nos. 00 ~ 09
3 Turn the SQL control to adjust the squelch
threshold.
4 Press [SCAN (SG.SEL] to start Memory Group
MGROUP-3 Memory Channel Nos. 30 ~ 39 Scan.
MGROUP-4 Memory Channel Nos. 40 ~ 49 • Scan ascends up through the channel
MGROUP-5 Memory Channel Nos. 50 ~ 59 numbers. (The scan direction cannot be
changed.)
• To jump to a desired channel while
MGROUP-7 Memory Channel Nos. 70 ~ 79 scanning, turn the MULTI/CH control or
MGROUP-8 Memory Channel Nos. 80 ~ 89 press and hold Mic [UP]/ [DWN].
MGROUP-9 Memory Channel Nos. 90 ~ 99 5 To stop Scan, press [SCAN (SG.SEL)] or
MGROUP-P Memory Channel Nos. P0 ~ P9 [CLR].
Note:
■ Scan Group Select ◆ If you have turned the SQL control clockwise, far beyond
the squelch threshold, Scan may fail to stop at a channel
You can select one or more groups to be scanned. in which a signal is present. If this happens, turn the
SQL control slightly counterclockwise.
First, select the groups to be scanned.
◆ When the current channel is within one of the groups
1 Press [M/V] to enter Memory Recall mode. that you selected, Scan starts with the current channel.
◆ When the current channel is outside all the groups that
• “ ” appears. you selected, Scan starts with the group number that
is larger than and closest to the group number of the
2 Press and hold [SCAN (SG.SEL)] to enter Scan current channel.
Group Select mode. ◆ Starting Memory Scan switches OFF the RIT and XIT
functions.
3 As you turn the MULTI/CH control, the
MGROUP number on the sub-display changes.
• MGROUP–0 represents Memory channels
0 ~ 9, MGROUP–1 represents Memory QUICK MEMORY SCAN
channels 10 ~ 19 and so on up to 1 Press [Q-MR] to enter Quick Memory mode.
MGROUP–9 which represents Memory
channels 90 ~ 99 and MGROUP-P which 2 Press [SCAN (SG.SEL] to start Quick Memory
represents Memory channels P0 ~ P9. Scan.
• Scan starts from the current quick memory
4 Press [M.IN] to select “on” to add the group to channel and ascends up through the channel
the Group Scan list. numbers. (The scan direction cannot be
• If you do not want to scan the selected changed.)
Group, press [SCAN (SG.SEL)] to select
“oFF”. 3 To stop Scan, press [SCAN (SG.SEL)] or [CLR].
5 Press and hold [SCAN (SG.SEL)] or [CLR]. to

exit the Scan Group Select mode.
49
OPERATOR CONVENIENCES
ANTENNAS Note:
◆ The APO function works even if the transceiver is scanning.
◆ The APO timer starts counting down when no key presses,
ANT 1/ ANT 2 no control adjustments, and no command (COM connector)
sequences are detected.
Two antenna connectors are available for the HF/
50 MHz band on the TX/ RX unit rear panel.
Press and hold [PRE (ANT 1/2)] to select ANT 1 or AUTOMATIC ANTENNA TUNER
ANT 2.
As explained in “ANTENNA CONNECTION”
• “ ” or “ ” appears to indicate which {page 1}, matching the impedance of the coaxial cable
antenna is selected. and antenna is important. To adjust the impedance
between the antenna and the transceiver, you have
the choice of using the internal antenna tuner or an
external antenna tuner. This section describes how
to use the internal antenna tuner. For the external
antenna tuner, consult the instruction manual that
RX ANT comes with the tuner.
Press and hold [ATT (RX ANT)] to toggle the RX ANT 1 Select the transmit frequency.
between enabled and disabled.
2 Press and hold [PRE (ANT 1/2)] to select “ ”
• “ ” appears when the RX ANT is enabled.
or “ ”.
DRV • If the external antenna tuner (AT-300) is
connected to the ANT 1 connector, select
Press and hold [METER (DRV)] to switch the DRV ANT 2 to use the internal antenna tuner.
between enabled and disabled. The internal antenna tuner is automatically
Use the standard input of 1 mW for the linear amplifier bypassed if the external antenna tuner is
and other connections. connected to ANT 1.
• “ ” appears when the DRV is enabled 3 Press and hold [AT (TUNE)].
The ANT 1, ANT 2, RX ANT, and DRV settings will • CW mode is automatically selected and tuning
automatically be stored in the antenna band memory. begins.
The next time you select the same band, the same • “ ” blinks and the TX-RX LED lights red.
antenna will be automatically selected. • To cancel tuning, press [AT (TUNE)] again.
Antenna Selection Frequency Range (MHz) • If the SWR of the antenna system is extremely
high (more than 10:1), an alarm (“SWR” in
0.03 ~ 0.522 10.5 ~ 14.5 Morse code) sounds and the internal antenna
0.522 ~ 2.5 14.5 ~ 18.5 tuner is bypassed. Before attempting to tune
again, adjust the antenna system to lower the
2.5 ~ 4.1 18.5 ~ 21.5 SWR.
4.1 ~ 6.9 21.5 ~ 25.5 4 Monitor the display and check that tuning has
6.9 ~ 7.5 25.5 ~ 30.0 successfully finished.
7.5 ~ 10.5 30.0 ~ 60.0 • If the tuning was successful, “ ” stops
blinking and the red TX-RX LED turns OFF.
Note: • If tuning does not finish within approximately
◆ Connect an external tuner to the ANT 1 connector only, 20 seconds, an alarm (“5” in Morse code)
then select ANT 1. The internal antenna tuner will be sounds. Press [AT (TUNE)] to stop the alarm
automatically bypassed when the transceiver is switched and tuning.
ON.
◆ The RX ANT can be used with less than 30 MHz. • If you want the transceiver to stay in
transmission mode after the tuning completes,
access Menu No. 51 and select “on”.
APO (Auto Power OFF) • To pass received signals through the internal
antenna tuner, access Menu No. 52 and select
You can set the transceiver to switch OFF “on”. When this function is ON, “ ” appears.
automatically if no keys or controls are pressed or This may reduce interference on the receive
adjusted for a certain period of time. One minute frequency.
before the transceiver switches OFF, “CHECK” is
output in Morse code.
2 Press [M.IN]/ [SCAN (SG.SEL)] to select the APO
time from “oFF”, “60”, “120”, or “180” minutes.
50
12 OPERATOR CONVENIENCES
Note: AUTO MODE

◆ The internal antenna tuner will not tune outside the available
transmission frequency limits. You can configure a maximum of 32 frequency
◆ Pressing [AT (TUNE)] for more than 1 second while borders (VFO A and B) to change the operating mode
transmitting interrupts transmitting and starts tuning. automatically as you change the VFO frequency.
◆ While using CW Full Break-in, the internal antenna tuner will
be in-line for both transmission and reception. As a default, the following modes are programmed on
◆ Tuning automatically turns OFF in approximately 60 each operating band.
seconds. “AT” disappears and the error beeps stop.
0.03 MHz ~ 9.5 MHz: LSB
◆ Tuning may still continue when the SWR meter indicates
1:1. This happens due to the tuning algorithm; this is not a 9.5 MHz ~ 60 MHz: USB
malfunction.
◆ Even though the SWR meter shows more than one segment, To add the frequency borders to the Auto Mode
the internal antenna tuner may not re-tune. This happens selection:
because of an SWR calculation algorithm tolerance.
◆ If tuning does not finish even though the SWR meter 1 With the transceiver power OFF, press and hold
indicates smaller than 3:1, adjust the antenna system to [LSB/USB] + [ ] to turn the transceiver ON.
lower the SWR, then attempt to tune again.
◆ Tuning may not reach an SWR of 1:1, depending on the
• “AUTOMODE” appears on the sub-display.
transceiver conditions. 2 Select an Auto Mode frequency memory channel
◆ The AT-300 cannot perform tuning on the 50 MHz band. number by turning the MULTI/CH control.
• Auto Memory channels 00 to 31 are available.
PRESETTING
3 Turn the Tuning control to select a desired
After each successful tuning session, the internal frequency border (or enter the frequency with the
antenna tuner Preset memory function stores the keypad {page 28}) to change the operating mode.
position of the tuning capacitor in memory. The
position of the capacitor is stored for each of the 4 Press [LSB/USB], [CW/FSK (REV)], [FM/AM (FM-
antenna tuner bands (see the following table) and for N)], or [DATA] until the desired communication
each antenna connector (ANT 1 and ANT 2). mode appears.
Press [AT (TUNE)]. 5 Repeat steps 2 ~ 4 until you have added all the
• “ ” or “ ”appears, showing that the antenna data.
tuner is in-line (not bypassed). 6 Press [CLR] to exit the Auto Mode frequency
• Each time you go across the antenna tuner configuration.
band, the internal antenna tuner Preset memory To activate the Auto Mode function:
is automatically recalled to position the tuning
capacitor without the need for retuning. If no 1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
preset data exists for a particular band/ antenna turn the MULTI/CH control to select Menu No. 23.
combination, then the default data of 50 Ω is used. 2 Press [M.IN] to select “on”.
Note: Tuning may restart in order to obtain the optimum
matching condition even though the current antenna tuner band 3 Press [MENU] to exit Menu mode.
has the preset data. Note: When using Auto Mode Frequency configuration, you
cannot use the Frequency Entry History function.
Internal Antenna Tuner Preset Frequency Range
(MHz)
0.03 ~ 1.85 14.1 ~ 14.5
1.85 ~ 2.50 14.5 ~ 18.5
2.50 ~ 3.525 18.5 ~ 21.15
3.525 ~ 3.575 21.15 ~ 21.5
3.575 ~ 3.725 21.5 ~ 25.5
3.725 ~ 4.1 25.5 ~ 29.0
4.1 ~ 6.9 29.0 ~ 30.0
6.9 ~ 7.05 30.0 ~ 51.0
7.05 ~ 7.1 51.0 ~ 52.0
7.1 ~ 7.5 52.0 ~ 53.0
7.5 ~ 10.5 53.0 ~ 60.0
10.5 ~ 14.1
51
The table below is an example of setting the Auto BEEP FUNCTION

Mode frequency.
The Beep function provides you confirmation of entry,
Channel Frequency Operation Range error status, and malfunctions of the transceiver.
Mode
No. (MHz) (MHz) Although you can turn the beep function OFF by
00 1.620 AM 0.030 ≤ f < 1.620 accessing Menu No. 03, we recommend you leave
it ON in order to detect unexpected errors and
01 2.000 CW 1.620 ≤ f < 2.000 malfunctions. You can also change the output level
02 3.500 LSB 2.000 ≤ f < 3.500 of the beeps by accessing Menu No. 03 and selecting
03 3.525 CW 3.500 ≤ f < 3.525 “1” to “9”.
04 10.100 LSB 3.525 ≤ f < 10.100 The transceiver generates the following Morse code
to tell you which mode is selected when you change
05 10.150 CW 10.100 ≤ f < 10.150 operating modes:
06 14.000 USB 10.150 ≤ f < 14.000
Mode Morse Code Output
07 14.070 CW-R 14.000 ≤ f < 14.070
08 14.112 FSK 14.070 ≤ f < 14.112
USB ••– (U)
09 18.068 USB 14.112 ≤ f < 18.068 LSB •–•• (L)
10 18.110 CW 18.068 ≤ f < 18.110 CW –•–• (C)
11 21.000 USB 18.110 ≤ f < 21.000 FSK •–• (R)
12 21.070 CW 21.000 ≤ f < 21.070 AM •– (A)
13 21.125 FSK-R 21.070 ≤ f < 21.125 FM ••–• (F)
14 21.150 CW 21.125 ≤ f < 21.150 USB-DATA ••– –•• (UD)
15 24.890 USB 21.150 ≤ f < 24.890 LSB-DATA •–•• –•• (LD)
16 24.930 CW 24.890 ≤ f < 24.930 CW-R –•–• •–• (CR)
17 28.000 USB 24.930 ≤ f < 28.000 FSK-R •–• •–• (RR)
18 28.070 CW 28.000 ≤ f < 28.070 FM-NAR ••–• –• (FN)
19 28.150 FSK 28.070 ≤ f < 28.150 FM-DATA ••–• –•• (FD)
20 28.200 CW 28.150 ≤ f < 28.200 FM-NAR-DATA ••–• –• –•• (FND)
21 29.000 USB 28.200 ≤ f < 29.000
The transceiver also generates the following warning,
22 30.000 FM-DATA 29.000 ≤ f < 30.000 confirmation, and malfunction beeps.
23 50.000 USB 30.000 ≤ f < 50.000
Beep Type Meaning
24 50.100 CW 50.000 ≤ f < 50.100
Short, high pitch A valid key is pressed.
25 51.000 USB 50.100 ≤ f < 51.000
Double, high pitch A secondary function is selected.
26 52.000 FM 51.000 ≤ f < 52.000
3 times, high pitch The third function is accepted.
27 52.000 LSB
A key entry is accepted, Scan
28 52.000 LSB Long, high pitch
starts, or AT tune has completed.
29 52.000 LSB
Short, regular A function is turned OFF.
30 52.000 LSB
Short, low pitch An invalid key is pressed.
31 52.000 LSB
The internal PLL circuit unlock
Morse “UL”
status is detected.
• The frequencies for channels 27 ~ 31 have not
been configured, but because they are the same CW Auto Tune cannot complete,
Morse “S”
frequency as channel 26, they will be FM mode or an invalid frequency is entered.
51.0 MHz ≤ f < 52.0 MHz. AT Tune cannot be completed
Morse “5”
• Since the frequencies above 52.0 MHz have not within the specified time.
been configured, they will be USB mode The antenna’s SWR is too high
Morse “SWR”
52.0 MHz ≤ f < 60.0 MHz (over 10:1) to perform AT tune.
1 minute before the APO (Auto
Power Off) function switches the
Morse “CHECK” transceiver OFF, a protection
circuit is ON. or an invalid
voltage is detected.
Waiting for a CW message to be
Morse “BT”
recorded.
The current message memory
Morse “AR”
is full.
52
DISPLAY Parameter Linear Amp. Control

oFF All controls Disabled
BRIGHTNESS
DC output (12 V) Enabled
The brightness of the LCD display can be selected
from OFF, and 1 to 6 . 1 Relay Disabled
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or TX delay 10 ms

turn the MULTI/CH control to access Menu No. 00. DC output (12 V) Enabled
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “oFF”, 2 Relay Enabled
“1”, “2”, “3”, “4”, “5”, or “6”. TX delay 10 ms
3 Press [MENU] to exit Menu mode. DC output (12 V) Enabled
3 Relay Enabled
BACKLIGHT COLOR
TX delay 25 ms
You can manually change the display illumination to
suit the lighting conditions where you are operating.
Note: If CW Full Break-in is enabled, 10 ms transmission delay
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or is applied regardless of the settings in Menu Nos. 53 and 54.
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “1”
(amber) or “2” (green). LOCK FUNCTIONS
3 Press [MENU] to exit Menu mode. FREQUENCY LOCK FUNCTION
Frequency Lock disables some keys and controls to
prevent you from accidentally activating a function or
PANEL KEY DOUBLE FUNCTION changing the current settings.
RESPONSE TIME Press and hold [FINE (F.LOCK)] to turn the
You can set the response time of double function Frequency Lock function ON or OFF.
panel keys to normal or fast. The default setting is • “ ” appears while this function is ON.
normal.
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “1” (0.2 The following keys and controls are disabled by
second), “2” (0.5 second) or “3” (1 second) Frequency Lock:
Key Comments
Tuning control Still operates in TF-SET mode.
LINEAR AMPLIFIER CONTROL MULTI/CH Still operates for changing setting
When you connect an external HF or 50 MHz control modes.
linear amplifier to the transceiver using the REMOTE [ENT]
connector, select “1”, “2”, or “3” to activate the internal
relay and/ or DC output (12 V) so you can interface Still operates for character
with the HF/ 50 MHz linear amplifier. The DC output [M.IN] selection and for changing setting
(12 V) works without any annoying chattering sounds modes.
(“1”) but the output current is limited to 10 mA. If your Still operates for character
linear amplifier control circuit draws more than DC 12 selection and for changing setting
V/ 10 mA, use relay switching (“2” or “3”) instead. [SCAN] modes. Also still operates for
setting up scan groups (press
Also, some linear amplifiers require a long
and hold).
transmission delay time because of the slow antenna
relay switching time. In this case, select “3” for slow Still operates in TF-SET mode
switching (25 ms delay). (in VFO mode) during Menu
Mic [UP]
mode when the mic key paddle
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or operation is ON.
turn the MULTI/CH control to select Menu No. 53
(HF) or 54 (50 MHz). Still operates in TF-SET mode
(in VFO mode) during Menu
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “oFF”, Mic [DWN]
mode when the mic key paddle
“1”, “2”, or “3”. operation is ON.
3 Press [MENU] to exit Menu mode. [A/B]
[M/V]
[SPLIT]
53
Key Comments MICROPHONE KEYS

Band direct key There are 4 microphone PF (Programmable Function)
keys: [PF1] , [PF2] , [PF3], and [PF4]. You can
[M>V] assign your own desired functions to these 4 keys
[LSB/USB] via Menu Nos. 81 to 84. You can also reprogram the
[CW/FSK] Mic [UP]/ [DWN] keys with your desired function by
accessing Menu Nos. 85 and 86.
Still operates to change between
[FM/AM] FM and FM Narrow (press and Assign one of the following functions to each PF key.
hold). Selecting “OFF” assigns no function to the PF key.
[DATA] No. Function Remark
[MHz] Menu No.
00 ~ 87
Still operates to cancel 00 ~ 87
[FINE]
Frequency Lock (press and hold). 100 RX ANT
Still operates to turn AGC ON/ 101 ANT1/2
[CWT]
OFF (press and hold).
102 VOX LEVEL
Still operates to turn Memory
Channel Lockout ON/OFF. Also 103 PROC LEVEL
[CLR]
still operates to end a setting 104 AT/TUNE Possible press and hold
mode.
105 CAR
Still operates to edit a Memory
[Q-MR] 106 TX-MONI
name.
107 KEY DELAY
Still operates to set or remove
a Slow Scan Frequency point 108 DRV
[Q-M.IN]
(press) or to remove all frequency 109 REV
points (press and hold).
110 FM-N
During Frequency Lock, the following functions which
have been assigned to PF keys will not function: 111 F.LOCK
112 NB LEV
Key Comments 113 NR LEV
[M.IN] 114 AUTO NOTCH
Still operates for setting up scan 115 NOTCH WIDE
[SCAN]
groups (press and hold).
116 CH1 Possible press and hold
[A/B]
[A=B]
[M/V]
[SPLIT]
120 RX Possible press and hold
[M>V]
121 A=B
[REV]
122 AGC SEL
[Q-MR]
123 TONE SEL
[Q-M.IN]
124 AGC OFF
[CWT]
125 Q-MR
Still operates in Menu mode and
[UP] 126 Q-M.IN
TF-SET mode (in VFO mode).
Still operates in Menu mode and 127 DRV
[DOWN]
TF-SET mode (in VFO mode). 128 SPLIT Mic [PF2] default
[EMERGENCY] 129 TF-SET
130 A/B Mic [PF1] default
PROGRAMMABLE FUNCTION KEYS 131 SCAN Possible press and hold
132 M>V Mic [PF3] default
TRANSCEIVER FRONT PANEL 133 M.IN
There are 2 PF (Programmable Function) keys on the 134 CW T.
transceiver front panel: [PF A] and [PF B]. You can
assign your own desired functions to these 2 keys by 200 VOICE1 [PF A] default
accessing Menu Nos. 79 and 80. 201 VOICE2 [PF B] default
54
No. Function Remark RX MONITOR

The lower meter when RX monitor temporarily disables the squelch function
202 VOICE3 to monitor the current frequency activities.
transmitting
203 MONITOR Mic [PF4] default To use the RX Monitor function, first assign the
function to a PF key (either on the front panel or the
204 TX TUNE microphone).
The input voice from
205 DATA SEND the data terminal is
turn the MULTI/CH control to select Menu No.
transmitted
79 ~ 86.
206 DOWN Mic [UP] default
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “203”.
207 UP Mic [DWN]default
Emergency frequency
208 EMERGENCY 4 Press the assigned [PF] key.
call (K type only)
OFF No function • While pressing [PF], the speaker unmutes.
Note:
◆ Assigned key functions may not work, depending on the TIME-OUT TIMER
setting.
The Time-out Timer limits the time of each
◆ [AGC SEL] can be used in modes other than FM mode, transmission. It is also useful to prevent a long
and can set a step level of the chosen AGC time constant
(FAST/ SLOW). accidental transmission.
◆ [TONE SEL] can also be used in FM mode while TONE or 1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
CTCSS is ON,
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “oFF”,
“3”, “5”, “10”, “20”, or “30” minutes.
DSP RX EQUALIZER
EQUALIZING RECEIVING AUDIO
Use Menu No. 31 to change the receiver frequency
responses of the target signal. You can select one TRANSVERTER
from 8 different receiver profiles including the default If you have a transverter that converts the TS-590S
flat response. Selecting any of the following items operating frequencies to other frequencies, you can
from the Menu causes “ ” to appear on the use this TS-590S transceiver as a transverter exciter.
display. Consult the instruction manual that came with the
• Off (oFF): transverter for interfacing to the TS-590S transceiver.
Slightly attenuates (1 kHz or higher audio
frequencies). FREQUENCY DISPLAY
• High boost 1 (hb1): 1 Connect the transverter to the ANT 1, ANT 2, RX
Emphasizes higher audio frequencies. ANT, or DRV connector of the TS-590S.
• High boost 2 (hb2): 2 Select the exciter operating frequency on the
Emphasizes higher audio frequencies but lower transceiver.
audio frequency attenuation is less than High • The transverter will use this frequency as the
boost1 (hb1). reference for converting frequencies.
• Formant pass (FP): 3 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
Improves clarity by suppressing audio frequencies turn the MULTI/CH control to access Menu No. 50.
outside the normal voice frequency range.
4 Press [M.IN]/ [SCAN (SG.SEL)] to select “1”.
• Bass boost 1 (bb1): • The output power is automatically set to the
Emphasizes lower audio frequencies. lowest power for that frequency (default). Refer
• Bass boost 2 (bb2): to “TX POWER” {below}.
Emphasizes lower audio frequencies but higher 5 Press [MENU] to exit Menu mode.
audio frequency attenuation is less than Bass
boost1 (bb1). 6 Press [ENT], then set the target converting
frequency using the numeric keys.
• Flat (FLAT):
The flat frequency response. 7 Press [ENT] to complete the entry.
• User (U): • The transceiver displays the target transverter
Reserved for the ARCP software. Off is frequency instead of the actual operating
programmed at the factory as a default. frequency.
55
Note: TX TUNE
◆ When using a transverter, not all the functions of this
transceiver are available. The TX Tune function allows you to adjust the
◆ When turning the transverter ON, the frequency entry history antenna length, or tune the linear amplifier while
is cleared, thus you cannot use the frequency entry history transmitting a continuous CW signal.
function.
◆ When using an antenna tuner in the IN state and the To use the TX Tune function, first assign the function
transverter is turned ON, the antenna tuner is forced to the to a PF key (either the front panel or Microphone PF
THRU state. keys).
TRANSMISSION OUTPUT POWER 1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to select a Menu No.
If Menu No. 50 is set to “1” {above}, the transceiver from 79 to 86.
automatically decreases the output power to 5 watts.
However, if you do not wish to decrease the output 2 Press [M.IN]/ [SCAN (SG.SEL)] to select “204”.
power, access Menu No. 50 and select “2”; the 3 Press [MENU] to exit Menu mode.
transceiver will transmit at full power.
4 Press the assigned [PF] key.
Note: You are responsible for your transmission output power
settings. • The transceiver automatically switches to CW
mode, and transmits a continuous carrier.
The transceiver selects the SWR meter function
TX MONITOR automatically.
• While in TX Tune mode, most keys are
TX monitor allows you to monitor the on-going disabled.
transmission sound. This is convenient when you
want to check the modulation sound quality of the • The default output power is configured as
transmission. In FSK mode, you can monitor the FSK 10 watts. However, you can adjust the output
signal that the transceiver is transmitting. power using [PWR (TX MONI)] and the MULTI/
CH control if necessary. The transceiver stores
1 Press and hold [PWR (TX MONI)]. the new output power setting when you exit the
• The current TX monitor setting appears on the TX Tune mode.
sub-display. 5 Press the assigned [PF] key again to exit the TX
2 Turn the MULTI/CH control to select the monitor Tune mode.
sound level from “oFF”, and “1” to “9”.
3 Press [CLR] to store the selected TX monitor level.
Note:
QUICK DATA TRANSFER
◆ We recommend you use headphones when you monitor This transceiver has the capability to quickly and
SSB, AM, or FM mode, in order to avoid howling. conveniently transfer the reception frequency and
◆ The CW transmission signal cannot be monitored using mode to another compatible transceiver. Compatible
the TX monitor function. Use the TX sidetone function to transceivers include:
monitor CW transmissions (Menu Nos. 04 and 34).
TS-590S TS-480HX/ SAT TS-2000/X

TX POWER TS-570S/ 570D TS-870S
You can adjust the transmission output power by Data transfer could be useful while contesting. A
pressing [PWR (TX MONI)] and turning the MULTI/ spotting station that is searching for new contest
CH control. If more precise power adjustment is multipliers can quickly transfer a frequency over to the
required, access Menu No. 48 and select “on”. When running (main) station.
this function is activated, the power adjustment steps
change as shown in the table below. SETTING UP
Mode Menu No. 48 OFF Menu No. 48 ON ■ Equipment Needed
SSB/ CW/ 5 ~ 100 W 5 ~ 100 W In addition to a compatible transceiver, to transfer
FM/ FSK in steps of 5 in steps of 1 to a TS-590S, TS-480HX/ SAT, TS-2000/X,
5 ~ 25 W 5 ~ 25 W TS-570S/D, or TS-870S, you must have 1 cross-
AM wired cable with a DB-9 female connector at both
in steps of 5 in steps of 1
ends.
Note: The output power settings are stored independently for
HF and 50 MHz. As shown in the table above, you can also ■ Connections
store different output power settings for AM and other modes for
HF bands and the 50 MHz band. For diagrams on how to connect the 2 transceivers,
refer to “CONNECTING PERIPHERAL
EQUIPMENT” {page 65}.
56
USING QUICK TRANSFER COMPUTER CONTROL

When connecting with another TS-590S, By connecting this transceiver to a computer, you
TS-480HX/ SAT, TS-2000/X, TS-570S/D/SG/DG, or can change the computer into an electronic console
TS-870S, use the same COM connector baud rate on from which you can remotely control functions of the
each transceiver. transceiver. This capability makes remote operation
Note: While transferring data, other functions may work slower. of your transceiver possible from across the room,
from another room, or when coupled with other
■ Transferring Data commercially available products and where lawful,
from another city, state, or country via an internet
The TS-590S transceiver works as the Master, connection.
sending data to the Slave transceiver.
1 Turn ON the Transfer function of each SETTING UP
transceiver.
• On the TS-590S, access Menu No. 58 and ■ Equipment Needed
select “on”. For the compatible transceiver, When connecting the TS-590S to a PC USB port:
refer to the instruction manual that came
with the transceiver. • USB 2.0 conformed (base) port
• Commercially available AB type USB 2.0 cable
2 On the Master, while in VFO mode, select an
operating frequency and mode. • Transceiver control application
3 On the Master, press [Q-M.IN]. • Pre-installed virtual COM port driver, on the PC.
(The driver is available at the website listed
• The displayed data is stored in Quick below.)
Memory channel 0 on the Master and
transferred to the Slave. When connecting the TS-590S to a PC COM port:
Note: If the Master has RIT switched ON, the offset • A PC equipped with a COM (serial) port
frequency is added to the reception frequency to be
transferred. • 1 straight cable. This cable must have a DB-9
female connector at one end, and a DB-9 or a
DB-25 female connector that mates with the
■ Receiving Data
COM port of your computer at the other end.
The TS-590S transceiver works as the Slave, • Transceiver control application
receiving data from the Master transceiver. The
Slave can receive data using either Quick Memory To create your programs, access the Kenwood
channel 0 or the VFO. website and download the TS-590S command
reference documents (pdf format) for details:
1 Switch ON the Transfer function of each
transceiver. http://www.kenwood.com/i/products/info/amateur/software_download.html
• On the TS-590S, access Menu No. 58 and

select “on”. For the compatible transceiver, ■ Connections
refer to the instruction manual that came To connect the transceiver to a computer, refer
with the transceiver. to the diagram in “CONNECTING PERIPHERAL
2 On the Slave, access Menu No. 59 and select EQUIPMENT” {page 65}.
either “oFF” (QUICK MEMO channel 0) or “on” Note: Before connecting this transceiver to a computer,
(the VFO). switch OFF the power to both the transceiver and the
computer.
• The default is OFF (QUICK MEMO).
3 On the Master, perform the appropriate COMMUNICATION PARAMETERS
operation to send data. In order to control the transceiver with the computer,
• For the correct method, refer to the you must first choose the communication parameters.
instruction manual that came with the
1 On the computer, configure your transceiver
transceiver.
control application for 8 data bits, 1 stop bit, and
Note: no parity.
◆ If you always use the TS-590S for receiving only,
activate the TX Inhibit function via Menu No. 60, to avoid 2 On the transceiver, select the same transfer rate
unintentional transmission. via Menu No. 61 (COM port) or 62 (USB port).
◆ When the Slave receives data using the VFO
programmed with a simplex frequency, the received data • The defaults are 9600 bps and 1 stop bit for
replaces the data on both VFOs. On the Slave, both RIT Menu No. 61 and 115200 bps and 1 stop bit for
and XIT are set to OFF. Menu No. 62.
◆ When the Slave receives data using the VFOs
programmed with split frequencies, the received data • Only a baud rate of 4800 bps uses 2 stop bits.
replaces the data only on the TX side of the VFO. On
the Slave, XIT is set to OFF but RIT is not changed. 3 Press [MENU] to exit Menu mode.
4 Turn the power OFF and then back ON to
implement the change.
57
EXTERNAL AUDIO SETTINGS • When not using the USB terminal, besides a serial
cable, create and connect a sound input/output
■ Selecting a Data Transmission Line cable. In this case when connecting to sound
equipment and the audio output level is too high,
Depending on how you connect your transceiver change the level setting in Menu No. 66.
to a PC, you will need to set a data transmission
line type. Access Menu No. 63 and select “ACC2”
(default) or “USB”. CONTROLLING THE TS-590S FROM A PC
If a PC and the TS-590S are connected using a
■ Audio Level Settings serial cable {page 67}, you can remotely control the
functions of the TS-590S from a PC. Download the
You can set the input and output audio levels of free ARCP-590 software from the following URL:
an ACC2 connection via Menu Nos. 66 and 67,
and the input and output audio levels of a USB http://www.kenwood.com/i/products/info/amateur/software
connection via Menu Nos. 64 and 65. Each setting _download.html
has a range of 0 to 9, with a default setting of 4.
The detailed remote controlling instructions are
Additionally, you can mix beep tones, the sidetone, available in accompanied documents and help file.
and the Voice guide for an ACC2/USB audio
output by accessing Menu No. 68 and selecting REMOTELY CONTROLLING THE TS-590S ON THE
“on” (whereby the PC will confirm the sounds being
output from the transceiver speaker).
NETWORK
In addition to the ARCP-590 program, the ARHP-590
CHANGING THE SIGNAL FOR THE COM TERMINAL program can also be downloaded from the above
site. This ARHP-590 program is an ARCP-590 host
Send the PSQ (SQL control signal) and PKS signal program that allows a user who is connected in the
through the COM terminal. network to remotely control the TS-590S transceiver
1 Turn the transceiver power OFF. from a distant location. If you make interface
cables that transfer the audio between the TS-590S
2 Press [FM/AM (FM-N)] + [ ]. transceiver and the PC on the host transceiver, you
• “PSQ/PKS” momentarily appears, and the can receive signals and transmit your voice over the
RTS/CTS signal is replaced with the PSQ/PKS network. For detailed information, download the
signal at the COM terminal. ARHP-590 program and consult the accompanied
documents.
3 Repeat steps 1 and 2 to return to normal operation.
Note: The ARHP-590 does not support voice communication.
• “CTS/RTS” momentarily appears. In order to use voice communications, you must also use
universal VoIP software.
The operation of the output signal for each setting is
as follows:
COM Terminal PC OPTIONAL VGS-1 VOICE GUIDE &

TxD RxD STORAGE UNIT
RxD TxD The optional VGS-1 unit allows you to record 30
CTS/ second (maximum) voice messages to memory
RTS CTS channels 1 and 2, and 15 second (maximum) voice
RTS
CTS RTS messages to memory channels 3 and 4. After
recording a message via your transceiver microphone,
GND GND you can then transmit those recorded messages. It
TxD (stopped) RxD also announces the key function and frequencies each
time you press a key (Voice announcement). Since
RxD (stopped) TxD the incoming reception signal is processed in digital
PSQ/ data in the transceiver, the VGS-1 can be configured
PSQ CTS
PKS to constantly store the incoming audio signals in the
PKS RTS background. If you wish, you can store the last 30
GND GND seconds of the incoming signal to the VGS-1 for the
later playback (Constant recording).
Normal PC commands (ARCP, ARHP, or SKY
COMMAND SYSTEM II) will not work when this For information on how to install the VGS-1 unit, refer
function is turned ON. to “INSTALLING OPTIONS” {page 71}.
• When operating the TS-590S as a base station, using
VoIP or similar software, set Menu No. 77 to “SQL”.
RECORDING MESSAGES
At the same time, if you are using CTCSS, set
Menu No 75 to “2” and confirm that the frequency This section explains how to record a single message.
is not already in use and is not causing any 1 Select SSB, FM, or AM mode.
interference.
• Select a mode that you wish to transmit.
• When turning the power OFF and the VoIP
software misdetects a busy signal, set Menu No. 2 Press and hold [CH1 (REC)] to record the
76 to “OPEN”. message for channel 1.
58
• BT in Morse code sounds and “AP 1 –” • To interrupt playback, press [CLR].

appears. • When Menu No. 56 is "oFF", pres and
hold the current playback channel key to
repeatedly play back the message saved
to that key (A display such as “AP 1111”
appears for the channel key you pressed.).
• To quit recording your message, press [CLR]. To cancel the playback, press any channel
3 Press [MIC (CAR)], then rotate the MULTI/CH key or [CLR].
control to adjust the microphone gain so that the 3 To play back another message in sequence,
ALC level is at maximum while the voice is at the press the corresponding key ([CH1 (REC)],
maximum level. [CH2 (REC)], [CH3 (REC)], or [RX/4 (REC)])
4 Hold [CH1 (REC)] and speak into your while the first message is being played.
microphone. • Repeat playback, by pressing and holding
• Four channels are available for recording the keys, does not work during consecutive
messages. Press [CH2 (REC)], [CH3 (REC)], message playback.
or [RX/4 (REC)] in place of [CH1 (REC)], in • Up to 4 channels can be queued.
steps 3 and 4 to record the message on a
different channel. ■ Sending Messages
• If Constant Recording is active, [RX/4 (REC)] is
1 Select SSB, FM, or AM mode.
unavailable for message recording.
• Select the same mode when you recorded
5 Release the key when you have finished recording the message.
your message.
2 Press [VOX (LEV)] to switch VOX ON or OFF.
• When the maximum recording time passes,
recording automatically stops. • If you switched VOX ON, skip step 3.
• The contents of the channel is overwritten with 3 Press [SEND] or hold Mic [PTT].
the new message.
4 Press [CH1 (REC)], [CH2 (REC)], [CH3
• “WRITING” appears while the transceiver is (REC)], or [RX/4 (REC)], depending on which
storing the message data to the VGS-1 flash channel you want to use.
memory.
• For example, “AP 1– – –” appears while
6 Repeat steps 2 to 5 to record a message on playing back the message in channel 1.
another channel. • To interrupt playback, press [CLR].
Note: Pressing [ ] cancels the recording in progress and
clears the memory channel. 5 To play back another message in sequence,
press the corresponding key ([CH1 (REC)],
MESSAGE PLAYBACK [CH2 (REC)], [CH3 (REC)], or [RX/4 (REC)])
while the first message is being played.
You can play back the message in channel 1, 2, 3, or • Up to 4 channels can be queued.
4 to check or send them. It is also possible to make
a longer message by consecutively playing back the 6 If you pressed [SEND] or Mic [PTT] in step 3,
messages of more than one channel, linking them press [SEND] again or release Mic [PTT].
together.
■ Erasing a Recorded Message
You can even repeatedly send a longer, linked
message by using the Repeat function. To switch 1 Press and hold [CH1 (REC)], [CH2 (REC)],
this function ON, access Menu No. 56 and select “on” [CH3 (REC)], or [RX/4 (REC)] to select the
(default is OFF). Then, select the repeat interval time message you want to erase.
in Menu No. 57 (default is 10 seconds). • “AP n – –” appears, where “n” represents the
Note: channel number.
◆ Pressing [ ] cancels the playback in progress.
◆ The settings in Menu Nos. 56 and 57 are shared with CW
2 To erase the recorded message, press and hold
Message Playback described in “CW MESSAGE MEMORY” the same key as in step 1 ([CH1 (REC)], [CH2
{page 34}. (REC)], [CH3 (REC)], or [RX/4 (REC)]) while
simultaneously pressing [CLR].
■ Checking Messages • A beep sounds and the message is erased.
1 Select SSB, FM, or AM mode.
■ Changing Inter-message Interval Time
• Select the same mode when you recorded
the message. For repetitive message playback, you can change
• Confirm that the VOX function is OFF. the interval between each series of messages.
Use Menu No. 57, and select the interval time in
2 Press [CH1 (REC)], [CH2 (REC)], [CH3 the range of 0 to 60 seconds.
(REC)], or [RX/4 (REC)], depending on which
channel you want to check.
• For example, “AP 1– – –” appears while
playing back the message in channel 1.
59
■ Changing Message Playback Volume Operations using VOICE1

Turning the AF control does not change the
Operation Announcement
volume for the message playback. To change the
message playback volume , access Menu No. 05 IF filter selection
“High” + Setting value1
to select the playback volume level from “1” to “9” (High Cut)
or “oFF”. IF filter selection
“Low” + Setting value1
(Low Cut)
CONSTANT RECORDING IF filter selection (Width) “Width” + Setting value1
By utilizing the digital recording capability of the IF filter selection (Shift) “Shift” + Setting value1
VGS-1, you can configure the VGS-1 to store the last
30 seconds of communications (transmitted signals Tone frequency
and received signals when the squelch opens). You selection/ when tone ID “Tone” + Setting value1
can play back the last 30 seconds of communications scanning is complete
to confirm what has been heard. CTCSS frequency
To activate the Constant Recording function, access selection/ when CTCSS “CTCSS” + Setting value1
Menu No. 55 and select “on” (default). “ ” appears ID scanning is complete
and the the transceiver starts recording the signal in NR1 level setup “NR1” + Setting value1
the background. When you press and hold [RX/4 NR2 level setup “NR2” + Setting value1
(REC)], the VGS-1 stores the last 30 seconds
(maximum) of the reception audio signal to the flash “Memory scan group” +
memory. While writing the audio signal data to the Group No. + “Off/On”
flash memory, “WRITING” appears. • When selecting a
To play back the stored reception signal, press [RX/4 group number, the
Memory scan group
(REC)]. To quit, press [CLR]. group number and “Off/
setup
On” is announced.
Note:
◆ While Menu No. 55 is ON, you cannot use channel 4 (RX/4) • When the settings are
to record and playback a voice message. However, the changed, only “Off/On”
message in channel 4 is not erased. When the Constant is announced.
Recording function is turned OFF (Menu No. 55 is OFF), you
can playback the message on channel 4. “VFO” + “Scan” + “Group”
◆ While “ ” is not displayed, such as the VGS-1 is playing + Section defined No. +
back a message or the Voice Guide function is working, the “Off/On”
Constant Recording function temporarily pauses.
◆ When you record a new message to the VGS-1, the 30 • When selecting the
second Constant Recording buffer is cleared. section defined number,
◆ You cannot transmit a stored audio signal that is recorded Program/VFO scanning
the section defined
with the Constant Recording function. section setup
number and “Off/On” is
announced.
VOICE GUIDE
• When the settings are
When the optional VGS-1 is installed, each time changed, only “Off/On”
you change the transceiver mode such as VFO A/ is announced.
B or Memory Recall, the transceiver automatically
announces the new mode. In addition, you can “VOX gain” + Setting
VOX gain level setup
program the front panel [PF A] or [PF B] key so value1
that pressing it makes the transceiver announce the Speech processor input “Processor in” + Setting
displayed information. If you are using the optional level setup value1
MC-47 microphone, you can program one of the Mic
Speech processor “Processor out” + Setting
[PF] keys for this function as well.
output level setup value1
The tables below indicate the transceiver
Noise Blanker “1” or “2” “Noise blanker” “1” or “2”
announcements when the settings are changed.
level setup + Setting value1
Additionally, pressing the [PF] key will perform
specific announcements depending on whether “Mic gain” + Setting
Mic Gain adjustment
VOICE1, VOICE2, or VOICE3 is selected. value1
“Keying Speed” + Setting
Keying Speed selection
VOICE1: value1
• When VOICE 1 auto announcement is ON (Menu “TX power” + Setting
TX power adjustment
No. 09), the transceiver settings are automatically value1
announced any time the settings are changed. “VOX delay” + Setting
VOX Delay time setup
• Pressing [PF] will announce the currently value1
displayed settings. Break-in Delay time “Break-in delay” + Setting
• During a voice announcement, pressing [PF] will setup value1
cancel the announcement. TX Monitor volume “TX monitor” + Setting
adjustment value1
60
Operation Announcement Status Announcement

Carrier level adjustment “Carrier” + Setting value1 Empty Channel:
AGC constant time AGC “Memory in” + Channel
“Fast” + Setting value1 Press [M.IN]
setting (FAST) number + “Blank”
While in Memory scroll
Stored Channel:
AGC constant time AGC mode
“Slow” + Setting value1 Channel number +
setting (SLOW)
(“S” +)1 Frequency
“Menu” + Menu number +
While in Menu mode Empty Channel:
Setting value1
Channel number +
1 During continuous operation, only the setting value is
Turn the MULTI/CH “Blank”
announced. control
Stored Channel:
Status Settings using VOICE1 Changing the channel Channel number +
number while in Memory (“S” +)1 Frequency
Status Announcement scroll mode
• Announces when
Press [ ] “VFO” + (“S” +)1 “A/B” + Menu No. 09 is ON
While in VFO mode Frequency Press [ENT]
Press [A/B (A=B)] While in frequency/ “Enter”
(“S” +)1 “A/B” + memory channel number
Changing VFO A or B Frequency entry mode
while in VFO mode
• Announces when Press [ENT], then
(TF-SET ON/OFF is Menu No. 09 is ON
stored) press the number keys
Enter the number while Entered number
Press [1.8] ~ [50] or
in frequency/ memory
[GENE]
channel number entry
Press [LSB/USB]/ [CW/ mode
FSK (REV)]/ [FM/AM Frequency
(FM-N)] Press [ENT], then turn
• Announces when
the MULTI/CH control
Changing the frequency Menu No. 09 is ON
while in VFO mode Displaying the frequency Frequency
history while in
Changing the mode
Frequency entry mode
while in VFO mode
Press the number keys
Press [M/V] “Channel” + Channel
Enter the number while “Enter” + Entered
While in Memory channel number + (“S” +)1
Frequency in memory scroll channel number
mode
number entry mode
Turn the MULTI/CH
“Auto” + Channel
control Press [LSB/USB] + [ ] number + Frequency
Changing the memory Channel number + While in Auto setting • Announces when
channel while in Memory (“S” +)1 Frequency mode Menu No. 09 is ON
channel mode • Announces when
Changing the mode Menu No. 09 is ON Turn the MULTI/CH
Channel number +
while in Memory channel control
Frequency
mode Changing the channel
• Announces when
number while in Auto
Hold or Release [TF- Menu No. 09 is ON
(“S” +)1 Frequency setting mode
SET]
• Announces when Press the number keys
TF-SET ON/OFF while in Frequency
Menu No. 09 is ON Changing the frequency/
Memory scroll mode • Announces when
mode while in Auto
Press [Q-MR] “Quick memory” + Menu No. 09 is ON
setting mode
Channel number +
While in Quick memory (“S” +)1 “A/B” + Press and hold [FINE]
mode Frequency “Frequency lock” +
Turning the frequency “On”/“Off”
Turn the MULTI/CH Channel number + lock ON/OFF
control (“S” +)1 “A/B” + Press [FM/AM (FM-N)]
Frequency CTS/RTS Output Mode:
Changing the memory +[ ]
“CTSRTS on”
channel while in Quick • Announces when Changing the output
memory mode Menu No. 09 is ON PSQ/PKS Output Mode:
signal for the PC control
“PSQPKS on”
terminal 2
61
Status Announcement VOICE3 Announcements
Press [A/B (A=B)] + SWR meter ALC meter

[ ], then turn the
Dot Dot
MULTI/CH control “VFO reset?” Announcement Announcement
position position
Reset confirmation
during VFO reset2 1 R 1.0 0 A0
Press [A/B (A=B)] + 2~6 R 1.5 1 A1

[ ], then turn the 7 ~ 11 R 2.0 2 A2
MULTI/CH control “Full reset?” 12 ~ 16 R 3.0 ~ ~
Reset confirmation
17 ~ 24 R 5.0 13 A 13
during Full reset2
1
25 ~ 30 R OVER 14 A 14
Announced when operating in Split-frequency mode.
2 Announced even when the auto Voice announcement is OFF. 15 ~ A OVER
3 When auto Voice announcement is ON, various configuration
images appear on the display. When modifications are made to COMP meter
these settings, the new setting is announced.
Dot
Announcement
position
VOICE2:
0 C 0 dB
• Pressing [PF] will announce the current state of
the S meter/ RF meter. 1 ~ 10 C 10 dB
• During a voice announcement, pressing [PF] will 11 ~ 20 C 20 dB
cancel the announcement. 21 ~ 30 C OVER
VOICE2 Announcements
■ Voice Guide Announcement Volume
S meter PWR meter
Turning the AF control does not change the
Dot Dot volume for the Voice Guide announcement. To
Announcement Announcement
position position change the announcement volume , access Menu
0 S0 0 P0 No. 06 and select the volume level from “1” to “7”
or “oFF”.
1~3 S1 1~3 P5
4~5 S2 4~6 P 10 ■ Voice Guide Announcement Speed
6 S3 7 ~ 12 P 25 If you feel the Voice Announcement speed is
7~8 S4 13 ~ 18 P 50 too slow or too fast, you can adjust the Voice
Announcement speed. Five different speeds can
9 S5 19 ~ 23 P 75
be configured. Access Menu No. 07 and select “0”
10 ~ 11 S6 24 ~ 30 P 100 to “4”, where 0 is the slowest speed and 4 is the
12 S7 fastest. The default speed is 1.
13 ~ 14 S8 ■ Voice Guide Announcement Language
15 S9 If you mistakenly change the announcement
16 ~ 19 10 dB language, you can change it back to English by
20 20 dB accessing Menu No. 08 and selecting “EN”.
21 ~ 24 30 dB
25 40 dB EMERGENCY CALL (K TYPE ONLY)
26 ~ 29 50 dB Section 97.401(d) of the regulations governing
30 60 dB amateur radio in the United States permit emergency
amateur communications on 5167.5 kHz by stations
VOICE3: in or within 92.6 km of the state of Alaska. This
• Pressing [PF] will announce the current state of frequency is for use only when the immediate safety
the SWR meter/ ALC meter/ COMP meter. of human life and/or property are threatened, and is
• During a voice announcement, pressing [PF] will never to be used for routine communications.
cancel the announcement. Press [EMERGENCY] to change to the Emergency
channel (5167.5 kHz/ USB).
• [EMERGENCY] can be programmed onto a PF
key.
• When entering Emergency mode, “EMERGENCY”
momentarily appears on the sub-display.
62
Note: DX PACKETCLUSTER TUNE

◆ RIT/XIT turns OFF automatically when entering Emergency
mode. If you have a TH-D72(A/E)/ TM-D710A/E(A/E)/ RC-
◆ The transceiver will not switch to the Emergency channel D710/ TM-D700(A/E), you can connect it to the TS-
if you are using the constant recorder and are either 590S transceiver to use the DX PacketCluster Tune
transmitting, receiving a voice call, or receiving a CW call.
function. Connect the 2 transceivers with a cross-
wired DB-9 cable as shown on page 70.
CROSSBAND REPEATER 1 On the TS-590S, press [MENU], then turn MULTI/
If you have a Kenwood FM transceiver (K type) with a CH control to select Menu No. 61.
6 pin mini DIN connector, you can set up the TS-590S
2 Press [M.IN]/ [SCAN (SG.SEL)] to select the same
transceiver and the FM transceiver as a crossband
communication baud rate configured on the TH-
repeater. The FM transceiver will receive signals you
D72/ TM-D710/ RC-D710/ TM-D700.
transmit from the additional VHF or UHF transceiver
when both transceivers are set with the same 3 Tune to the DX PacketCluster node frequency on
frequency. The signal is then routed to the the TH-D72/ TM-D710 RC-D710/ TM-D700.
TS-590S transceiver and retransmitted on the
frequency you have set on the TS-590S transceiver. 4 Using [TNC], enter the APRS mode on the
Likewise, signals received on the TS-590S transceiver TM-D710/ RC-D710/ TM-D700.
are routed to the FM transceiver and retransmitted • “APRS” or “TNC APRS” appears on the
to the transceiver you have with you, allowing you to TH-D72/ TM-D710/ RC-D710/ TM-D700
hear the received call in a distant location. display.
To interface between the TS-590S transceiver and 5 Using [DX], enter the DX PacketCluster mode on
FM transceiver (K type), refer to “CROSSBAND the TH-D72/ TM-D710/ RC-D710/ TM-D700.
REPEATER” {page 70}. • Every time the DX station’s information is
Note: For the repeater function to operate, the squelch levels reported to the DX PacketCluster node, the
of both transceivers (TS-590S and FM transceiver) must be TH-D72/ TM-D710/ RC-D710/ TM-D700 stores
adjusted properly so that no background noise can be heard; the
transmission is controlled by monitoring the squelch status only. and lists the report to the memory.
6 Select a desired DX station data with [▲]/ [▼] on
OPERATION the TH-D72/ TM-D710/ RC-D710/ TM-D700.
The crossband repeater function uses 2 frequency 7 Press [TUNE] on the TM-D710/ RC-D710 or
bands to receive and transmit signals. When a signal [MENU] on the TH-D72 or [MHz] on the TM-D700
is received on one band, it is retransmitted on the to transfer the frequency data to the TS-590S
other band. transceiver.
• If the transferred frequency data is available
1 Select a transmission/ reception VHF or UHF on the TS-590S transceiver, the frequency
frequency on the FM transceiver. data will be overwritten to the current operating
2 Confirm the PTT icon is visible on the crossband frequency. Otherwise, the operating frequency
repeater frequency on the FM transceiver. of the TS-590S transceiver remains unchanged.
3 Select the same frequency for the terminal For more detailed information on the DX
transceiver. PacketCluster operation of the TH-D72/ TM-D710/
RC-D710/ TM-D700, refer to their respective
4 Select a HF/ 50 MHz frequency on the TS-590S instruction manuals.
transceiver.
Note: The firmware of the TM-D700(A/E) transceiver must be
5 Adjust the squelch threshold level so that both the version G2.0 or later to use the DX PacketCluster Tune function.
TS-590S and FM transceivers mute.
6 On the TS-590S, press [MENU], then turn MULTI/
CH control to select Menu Nos. 73 and 74.
• When the TS-590S transceiver’s squelch
opens, the FM transceiver simultaneously
retransmits the incoming audio signal on the
VHF or UHF frequency.
• When the FM transceiver’s squelch opens, the
TS-590S transceiver retransmits the incoming
audio signal on the HF/ 50 MHz frequency.
8 Access Menu Nos. 66 and 67 and press [M.IN]/
[SCAN (SG.SEL)] to adjust the input/ output audio
level.
9 To quit the FM repeater operation, disconnect the
interface cable between the transceivers, then
access Menu Nos. 73 and 74 on the TS-590S
transceiver and select “oFF”.
63
SKY COMMAND SYSTEM II PREPARATION

Sky Command System II allows you to remotely Although you can use a TH-D7A, TH-D72A/E,
control the TS-590S transceiver from a separate TM-D710A, TM-V71A + RC-D710, or TM-D700A
location. transceiver as a “Commander” (an external remote
control unit), the following procedure shows how
If you have more than 2 TH-D7A/ TH-D72A/E/ to set up your TS-590S and TH-D7A, TH-D72A/E,
TM-D710A/ TM-V71A + RC-D710/ TM-D700A TM-D710A, TM-V71A + RC-D710, or TM-D700A
transceivers (K type), you can perform Sky Command transceivers as a “Transporter” at a base station and
System II operation to remotely control the HF/ 50 the TM-D710A, TM-V71A + RC-D710, or TM-D700A
MHz band of your TS-590S transceiver. transceiver as a “Commander”.
You will use one transceiver (TH-D7A, TH-D72A/E,
TM-D710A, TM-V71A + RC-D710, or TM-D700A) as a Starting Sky Command System II operation:
remote control unit, called a “Commander”. The other
After you have completed setting up the following, you
VHF/ UHF transceiver (TH-D7A, TH-D72A/E,
can start Sky Command System II operation. Without
TM-D710A, TM-V71A + RC-D710, or TM-D700A) with
programming these parameters, you cannot use Sky
the TS-590S transceiver is called the “Transporter”.
Command System II.
This TH-D7A, TH-D72A/E, TM-D710A, TM-V71A +
RC-D710, or TM-D700A transceier will function as
an interface between the Commander (a remote TS-590S + TH-D7A/ TH-D72A/E/ TM-D700A/
control unit) and the HF/ 50 MHz band of the TS-590S TM-D710A/ TM-V71A + RC-D710 (Transporter)
transceiver. Setup:
This system allows you, for example, to watch for and 1 Configure the TH-D7A, TH-D72A/E, TM-D710A,
hunt DX while washing your car, or to operate the HF TM-V71A + RC-D710, or TM-D700A as a
transceiver while relaxing in your car, living room, or “Transporter” and connect all the necessary cables
patio, instead of actually operating inside your shack. to the TS-590S transceiver.
Note: Operation of Sky Command System II may not been 2 Select a frequency (HF/ 50 MHz band) on the
permitted in certain countries. Check your local laws before TS-590S transceiver.
operating.
3 On the TS-590S, press [MENU], then turn MULTI/
CH control to select Menu No. 61.
4 Press [M.IN]/ [SCAN (SG.SEL] to select the the
desired communication speed.
5 Select the same communication parameters to
match the TH-D7A, TH-D72A/E, TM-D710A,
TM-V71A + RC-D710, or TM-D700A transceiver
7 Configure and start the Transporter mode on the
SKY COMMAND SYSTEM II DIAGRAM TH-D7A, TH-D72A/E, TM-D710A, TM-V71A +
RC-D710, or TM-D700A transceiver.
VHF freq.
Audio Audio
• Refer to the respective instruction manuals of
UHF freq. the TH-D7A, TH-D72A/E, TM-D710A, TM-V71A
Audios Control commands + RC-D710, or TM-D700A for information on
Control commands tResponse how to connect, configure, and operate the
tResponse
transceivers for Sky Command System II.
Commander Transporter
64
CONNECTING PERIPHERAL EQUIPMENT
TERMINAL DESCRIPTIONS
COM CONNECTOR
Pin No. Pin Name Function I/O
1 NC No connection —
2 RXD Transmit data O
3 TXD Receive data I
5 GND Ground —
7 RTS Receive enable I
8 CTS Transmit enable O
ACC2 CONNECTOR
2 RTTY RTTY key input I
Audio output from the transceiver
• Connect to the audio input of the TNC, MCP, or PC (or PC
interface connection).
• Audio output level is independent from the AF control setting.
3 ANO • Audio output level can be changed by adjusting the value O
in Menu No. 67. Set the value to a moderate audio output
level. The default value of 4 is approximately 0.5 Vp-p, which
is a standard modulating signal. The settings of 0 ~ 9 vary
from approximately 0 Vp-p to 1.2 Vp-p.
• Impedance: Approx. 10 kΩ.
4 GND Ground —
Transceiver squelch control
• Connect to the squelch input of the TNC, MCP, or PC
5 PSQ connection interface. O
• Squelch open: Low impedance
• Squelch closed: High impedance
8 GND Ground —
PTT input for data communication
• Connect to the PTT output of the TNC, MCP, or PC
9 PKS connection interface.
I
• Microphone audio input mutes when transmitting.
Audio input for data communication
• Connect to the audio output of the TNC, MCP, or PC (or PC
interface connection).
• Audio input level is independent from the microphone gain
(set with the [MIC] key).
11 ANI I
• Audio input level can be changed by adjusting the value in Menu
No. 66. The default value of 4 is approximately 10 mVrms, which
is a standard modulating signal. The settings of 0 ~ 9 vary from
approximately no modulation to approximately 1 mVrms.
• Impedance: Approx. 10 kΩ.
12 GND Ground —
PTT input (same as the front panel MIC connector)
13 SS • During transmission, the audio input of ACC2 connector I
terminal 11 (ANI) and the USB terminal are muted.
65
13 CONNECTING PERIPHERAL EQUIPMENT
REMOTE CONNECTOR
1 SPO Speaker output O
2 COM Common terminal I/O
Standby; when grounded, the transceiver enters TX
mode.
3 SS I
• During transmission, the audio input of ACC2 connector
terminal 11 (ANI) and the USB terminal are muted.
When connected with the common terminal, the amplifier
4 MKE I/O
enters TX mode.
When connected with the common terminal, the amplifier
5 BRK I/O
enters RX mode.
6 ALC ALC input from the amplifier (approx. -7 V). I
Approx. +12 V DC is output when in TX mode (10 mA
7 RL O
max.).
EXT.AT CONNECTOR (for AT-300)

1 GND Ground —
2 TT AT-300 control input/ output I/O
3 GND Ground —
5 TS AT-300 control input/ output I/O
6 14S Power supply for EXT.AT Switched 13.8V. O
MIC CONNECTOR
1 MIC MIC signal input I
2 SS MIC standby (PTT) control I
3 MD MIC Down control I
4 MU MIC UP control I
5 8A Switched 8V O
7 MSG MIC GND —
8 MCG GND —
66
Note: Use a USB/ RS-232C cable shorter than 3 meters.
COMPUTER
The USB connector allows you to directly connect a computer by using a USB (AB type) or RS-232C cable. By
connecting a USB cable to the PC, you can enable the input and output of the transmission and reception of sound.
You must use the ARUA-10 software, available at the following URL, to control the USB audio system line of the
PC. (The virtual COM port driver can also be downloaded from the following URL.)
http://www.kenwood.com/i/products/info/amateur/software_download.html
TS-590S
To RS-232C serial port
(f)
To USB port
(f)
RS-232C straight
cable
Personal computer
USB cable
• To transmit the signal from the PC, you must either turn the DATA VOX function ON or ground pin 9 (PKS) of
the ACC2 connector to pin 8 (GND). (Refer to page 30 for the DATA VOX function.)
Note:
◆ The USB cable and RS-232C cable are not included; purchase them separately.
◆ Connect the USB cable directly to the PC.
◆ In theory, a delay occurs in the USB audio system. Therefore, sound may be clipped when using a PC in this system. Use this USB
audio system in cases where you are recording communications that do not require quick responses to a PC.
COMPATIBLE TRANSCEIVER
When transferring data to or from another TS-590S, TS-480HX/SAT, TS-2000/X, TS-570S/D, or TS-870S, directly
connect the 2 transceivers using the COM connectors.
TS-590S Compatible transceiver
(f) (f) DB-9 connector wiring (Cross-wired)
RS-232C cross cable
67
RTTY OPERATION
Use the ACC 2 connector to interface with your MCP. If your MCP supports RTTY keying output, connect the
output to pin 2 of the ACC 2 connector. Connect the demodulation input line of the MCP to pin 3 of the ACC 2
connector. Also, connect the transmission control line of the MCP to pin 13 of the ACC 2 terminal. Select “FSK” or
“FSR” when you operate the RTTY mode.
Note: Do not share a single power supply between the transceiver and the RTTY equipment. Keep as wide a separation as possible
between the transceiver and the RTTY equipment to reduce noise-pickup by the transceiver.
TS-590S
Power supply for MCP
MCP
Personal computer
HF/ 50 MHz LINEAR AMPLIFIER

Connect an external transmission power amplifier to the REMOTE connector. Switch ON the linear amplifier
control relay via Menu No. 53 (HF) or 54 (50 MHz). Select “2” or “3” if you use the internal relay to control the linear
amplifier status.
The TX/ RX relay response time is 10 [ms] when you have selected CW Full Break-in and 25 [ms] when you have
selected CW Semi Break-in.
Note: The TX/ RX control method differs, depending on external amplifier models. Some amplifiers enter the TX mode when the control
terminal is grounded. For those amplifiers, connect pin 2 of the REMOTE connector to the GND terminal of the amplifier and connect pin 4
of the connector to the control terminal of the amplifier.
TL-922 (HF linear amplifier)
TS-590S
(The TL-922 Linear Amplifier is

a discontinued model. It may
no longer be available in your
Control relay area.)
R
T 2
1
4 5
3
REMOTE connector
6 7 (front view)
GND
68
ANTENNA TUNER
Use the ANT 1 and AT connectors to connect an AT-300 external antenna tuner. If you connect the external
antenna tuner to the ANT 2 connector, it will not function.
Note: The AT-300 cannot be used for 50 MHz operation.
ANT 1
connector
TS-590S
AT-300
(The AT-300 Antenna Tuner is

a discontinued model. It may
no longer be available in your
area.)
TNC AND MCP

Use the DATA connector to connect the Audio input/ output lines from a Terminal Node Controller (TNC) for Packet
operation, a Multimode Communications Processor (MCP) for operation on AFSK, Packet, PacTOR, AMTOR,
G-TORTM, PSK31, or FAX, or a Clover interface. Also use the ACC 2 connector to connect SSTV and phone patch
equipment.
• Connect the TNC or MCP to the ACC 2 connector using a cable equipped with a 13-pin DIN plug.
• Connecting the TNC or MCP to a personal computer or dumb terminal requires an RS-232C cable.
• Select LSB or USB mode (it depends on the communication mode) when you operate the MCP/ TNC.
Note: Do not share a single power supply between the transceiver and the TNC or MCP. Keep as wide a separation as possible between
the transceiver and the computer to reduce noise-pickup by the transceiver.
TS-590S
Power supply for TNC/ MCP
TNC/MCP
Personal computer
69
DX PACKETCLUSTER TUNE
If you have a TH-D72A/E/ TM-D710A/E/ RC-D710/ TM-D700A/E, you can connect the TH-D72A/E/ TM-D710A/E/
RC-D710/ TM-D700A/E to the TS-590S transceiver to use the DX PacketCluster Tune function. Connect the 2
transceivers with a cross-wired RS-232C cable as shown below. (For connecting to the TH-D72A/E, refer to the
TH-D72A/E instruction manual.)
RS-232C cross cable
TS-590S
TM-D710A/E/
RC-D710 + TM-V71A/E
(m)
(f)
TM-D700A/E
(f)
RC-D710 + PG-5J
(f)
PG-5G
CROSSBAND REPEATER
If you have a Kenwood FM transceiver (K type) with a 6 pin mini DIN connector, you can connect the FM
transceiver to the TS-590S transceiver to use the Crossband repeater function. Connect the 2 transceivers with a
DIN (13-pin)/ mini DIN cable (6-pin) as shown below.
DIN (13-pin)/ Mini DIN (6-pin)

TS-590S
TM-D710A/ TM-V71A TM-D700A
DIN (13-pin) pulg Mini DIN (6-pin) pulg

PKS
ANI PR1
SQC
ANO PKD
PSQ PKS
After connecting the 2 transceivers with the cable, access Menu Nos. 73 (PKS polarity) and 74 (Busy lockout) on
the TS-590S transceiver and select “on”. You will further need to adjust the audio input/ output level of the TS-
590S transceiver using Menu Nos. 66 and 67.
70
INSTALLING OPTIONS
You will require a #1 Philips screwdriver to install the VGS-1 VOICE GUIDE & STORAGE UNIT
VGS-1 or SO-3 TCXO. You will also need a soldering
iron (approx. 30 watts) to install the SO-3 TCXO. 1 Remove the shield cover (4 screws).
Switch OFF the transceiver power and unplug the DC power

cable before performing any installations.
REMOVING THE BOTTOM CASE

When installing the optional VGS-1 or SO-3 TCXO,
remove the bottom case of the transceiver:
1 Remove the 10 screws.
2 Lift off the bottom case.
2 There are 5 rubber cushions in the VGS-1

package. Use the 2 rubber cushions shown below
(20 x 30 x 2 mm and 21 x 21 x 2.5 mm) and attach
them to the VGS-1.
• The remaining cushions are not used.
3 Plug the VGS-1 into the VGS-1 connector of the

PC board, pressing down on the top of the VGS-1
until secure.
4 Replace the shield cover and tighten the 4 screws.

5 Replace the bottom case (10 screws).
Note: After installation, you can adjust the VGS-1 playback and
voice guide volume by selecting Menu Nos. 05 and 06.
71
14 INSTALLING OPTIONS
SO-3 TCXO REFERENCE FREQUENCY CALIBRATION

The SO-3 option improves the transceiver frequency Note: The transceiver is adjusted at the factory prior to
shipping. Do not perform this adjustment unless it is necessary.
stability to ±0.5 ppm.
1 Set the following on the transceiver:
1 Remove the CN503 connector and TCXO PCB
screw, as shown below. • Mode: CW
• AF control: Center
CN503 • Menu No. 34 (CW RX pitch): 800 Hz
TCXO PCB • SHIFT control: 800 Hz
• RIT function: OFF
• Break-in function (VOX): OFF
2 Remove the bottom case (10 screws) from the
transceiver.
3 Tune in a standard frequency station such as
WWV or WWVH at, for example, 10.000.00 MHz or
15.000.00 MHz.
• Adjust the Tuning control so that the display
reads the exact frequency of the station.
• You should hear a beat tone of approximately
2 Remove the TCXO PCB. 800 Hz.
3 Insert the SO-3 TCXO. • For 800 Hz:
faf = (fdisplay/15.600 x Δfreference) + 800 Hz
where Δfreference is the shift from the 15.6 MHz
reference frequency.
4 Close your CW key. You will hear a transmit
sidetone of approximately 800 Hz.
• This sidetone produces a double beat tone
when it combines with the received signal.
4 Solder all pins on the reverse side of the PCB. • Adjust the AF control to hear the double beat
5 Re-insert the TCXO PCB in the transceiver. clearly.
6 Connect the CN503 and tighten the screw. • For 800 Hz:
fsidetone = 800 Hz ±50 ppm (= 800 ±0.04 Hz)
7 Move the C903 and C904 jumper as shown below. where Δfreference is the shift from the 15.6 MHz
reference frequency.
5 TS-590S transceiver without SO-3:
Adjust the trimmer (TC501) to minimize the
frequency difference between the received 800 Hz
tone and the 800 Hz sidetone.
TC501 CN904 TS-590S transceiver with SO-3:
CN903
Adjust the trimmer inside the SO-3 using the
supplied plastic adjustment tool. Minimize the
frequency difference between the received 800 Hz
tone and the 800 Hz sidetone.
Note:
◆ To avoid misplacing the jumper, keep it attached to 1 pin of
C903 or C904.
◆ When removing the SO-3 TCXO, replace the jumper to its
original position.
8 Replace the bottom case (10 screws).
72
14 INSTALLING OPTIONS
MB-430 MOBILE BRACKET PRECAUTIONS

ATTENTION: When installing the MB-430, use the SEMS • When operating mobile, do not attempt to
Screws provided with the TS-590S. configure the transceiver while driving; it is too
When installing the MB-430, attach the supplied dangerous.
plastic spacers to the transceiver in advance. This • Use of the transceiver while you are driving may be
is necessary to protect the TS-590S transceiver from against traffic laws. Please check and observe the
scratches. vehicle regulations in your area.
Plastic spacers
Make sure the tab faces out
Once the bracket is installed onto the vehicle, prepare

the transceiver by loosely screwing in the rear screws.
Hook those screws onto the rear guide rail of the
mounting bracket then adjust the transceiver to your
desired angle before tightening the screws. Insert and
tighten the front screws to secure the transceiver in
place.
Front screw
Rear screw
To remove the transceiver from the bracket, first

remove the front screws, then loosen the rear screws
slightly and pull the transceiver forward to unlatch it
from the bracket.
Do not install the transceiver so that it is vertically on its side.
73
TROUBLESHOOTING
GENERAL INFORMATION SERVICE NOTE
Your transceiver has been factory aligned and If you desire to correspond on a technical or
tested to specification before shipment. Under operational problem, please make your note short,
normal circumstances, the transceiver will operate complete, and to the point. Help us help you by
in accordance with these operating instructions. providing the following:
All adjustable trimmers, coils, and resistors in the
transceiver are preset at the factory. They should • Model and serial number of equipment
only be readjusted by a qualified technician who is • Question or problem you are having
familiar with this transceiver and has the necessary
test equipment. Attempting service or alignment • Other equipment in your station pertaining to the
without factory authorization may void the transceiver problem
warranty. • Meter readings
When operated properly, the transceiver will provide • Other related information (Menu setup, mode,
years of service and enjoyment without requiring frequency, key sequence to induce malfunction,
further realignment. The information in this section etc.)
gives some general service procedures requiring little
or no test equipment.
Do not pack the equipment in crushed newspapers for shipment.
SERVICE Extensive damage may result during rough handling or shipping.
If it is ever necessary to return the equipment to Note:

your dealer or service center for repairs, pack the
◆ Record the date of purchase, serial number, and dealer from
transceiver in its original box and packing material. whom the transceiver was purchased.
Include a full description of the problems experienced. ◆ For your own information, retain a written record of any
Include both your telephone number and fax number maintenance performed on the transceiver.
(if available) along with your name and address in ◆ When claiming warranty service, please include a photocopy
case the service technician needs to call for further of the bill of sale or other proof-of-purchase showing the
date of sale.
information while investigating your problem. Don’t
return accessory items unless you feel they are
directly related to the service problem. Please do not CLEANING
send subassemblies or printed circuit boards. Send The keys, controls, and case of the transceiver are
the complete transceiver. likely to become soiled after extended use. Remove
You may return your transceiver for service to the controls from the transceiver and clean them with
the authorized Kenwood dealer from whom you a neutral detergent and warm water. To clean the
purchased it or any authorized Kenwood service case, use a neutral detergent (no strong chemicals)
center. A copy of the service report will be returned and a damp cloth.
with the transceiver.
Tag all returned items with your name and call sign for
identification. Please mention the model and serial
number of the transceiver in any communication
regarding the problem.
74
15 TROUBLESHOOTING
TROUBLESHOOTING
The problems described in this table are commonly encountered operational malfunctions. These types of
difficulties are usually caused by improper hook-up, accidental incorrect control settings, or operator error due to
incomplete programming. These problems are usually not caused by circuit failure. Please review this table and
the appropriate section(s) of this instruction manual before assuming your transceiver is defective.
Note: Placing a powered portable transceiver near this transceiver may cause noise in the transceiver.
Problem Probable Cause Corrective Action Page

The transceiver will 1 DC power supply is OFF. 1 Switch the DC power supply ON. 10
not power up after 2 Faulty power cable. 2 Inspect the power cable. Confirm that the 1
connecting a 13.8 V polarities are correct (Red: positive (+); Black;
DC power supply and negative (–)).
pressing [ ]. 3 The power cable is not 3 Confirm the connections to the DC power 1
Nothing appears connected securely. supply are secure.
on the display and 4 The power cable fuse is 4 Look for the cause of the blown fuse. After 2
no receiver noise is open. inspecting and correcting any problems,
heard. install a new fuse of the specified rating.
After switching 1 The input voltage is outside 1 Correct the input voltage or use a 12 ~ 16 V 1
the power ON, the 13.8 V DC ±15% (11.7 ~ battery.
transceiver does not 15.8 V DC)
function normally. For 2 The microprocessor has 2 Review “MICROPROCESSOR RESET”. 78
example, no digits or malfunctioned. After understanding what data will be lost, do
incorrect digits appear a VFO Reset. If the problem remains, do a
on the display. Full Reset.
After switching the The current rating of the DC Use a DC power supply that has a 20.5 A or 1
transceiver ON, the power supply is too low. higher current rating
transceiver refuses to
transmit.
The transceiver does 1 Procedures are not being 1 Review “WRITING CONVENTIONS ii
not respond correctly followed precisely. FOLLOWED”.
after pressing key 2 The Frequency Lock 2 Press and hold [FINE (F.LOCK)] to switch 53
combinations or function is ON. the function OFF. The “ ” icon disappears.
turning controls per 3 The microprocessor and its 3 Review “MICROPROCESSOR RESET”. 78
instructions in this memory need to be reset. After understanding what data will be lost, do
manual. a Partial Reset. If the problem remains, do a
Full Reset.
The frequency cannot The Frequency Lock function Press and hold [FINE (F.LOCK)] to switch the 53
be changed. is ON. function OFF. The “ ” icon disappears.
SSB audio quality is 1 The wrong operation mode 1 Select USB or LSB for the mode. 11
very poor; the high or is selected for the receiver.
low audio frequencies 2 The IF filter is incorrectly 2 Turn the HI/SHIFT or LO/WIDTH control to 38
are absent. set. adjust the DSP filter width.
3 Noise Reduction 1 or 2 is 3 Press [NR (LEV)] until the NR function turns 39
ON. OFF.
4 Beat Cancel 1 or 2 is ON. 39
4 Press [BC (A.NOTCH)] until the BC function
turns OFF.
No signals are 1 The SQL control is fully 1 Turn the SQL control counterclockwise. 12
received or receive clockwise.
sensitivity seems 2 The Attenuator is ON. 2 Press [ATT (RX ANT)] to switch the 40
poor. 3 MIC [PTT] is pressed. Attenuator is OFF.
3 Release MIC [PTT]. 13
4 The IF filter bandwidth was 4 Review “DSP FILTERS”, and set the 38
incorrectly set. controls accordingly.
5 The wrong antenna 5 Press and hold [PRE (ANT 1/2)] to select the 50
connector (ANT 1 or ANT other antenna connector.
2) was selected.
6 The pre-amplifier is OFF. 6 Press [PRE (ANT 1/2)] to switch the function 40
ON.
7 An internal DSP error 7 Restart the transceiver by turning the power —
occurs. OFF and then back ON. If the problem
persists, consult Kenwood authorized
Service Center.
75
15 TROUBLESHOOTING

No signals are The RF gain was set too low. Turn the RF control clockwise to increase the RF 10
received or receive gain.
sensitivity seems
poor; S-meter is
reading full scale.
Received signals The wrong modulation was Select the correct modulation mode. 11
are completely selected.
unintelligible
Memory Scan will not 1 The SQL control was not 1 Adjust the SQL control to just eliminate 12
start scanning. set correctly. background noise.
2 Less than 2 memory 2 Unlock at least 2 memory channels. 44
channels were unlocked.
3 Less than 2 memory 3 Store data in at least 2 memory channels. 41
channels were
programmed.
Memory Scan will With Group Scan selected, the Select the Memory Group that contains the 49
not scan one of the channel you want to scan is in memory channel you want to scan.
stored channels; the a different group.
desired channel is not
locked out.
Program Scan will not The start and end frequencies Store different start and end frequencies. 46
start scanning. are identical
AT does not finish The impedance of the coaxial Adjust the antenna system to lower the SWR. 50
successfully. cable and antenna was not
matched. Tuning does not
successfully finish depending
on conditions, although the
SWR meter indicates smaller
than 3:1.
The internal tuner is The SWR of the antenna Adjust the antenna system to lower the SWR 50
bypassed immediately system is too high.
after tuning is started.
You cannot transmit 1 The microphone plug was 1 Turn OFF the power, ensure the MIC 2
even though you not inserted completely into connector has no foreign objects in it, then
press MIC [PTT], or the MIC connector. plug in the connector firmly.
transmissinos result 2 The Transmit Inhibit 2 Change Menu No. 60 to OFF. 32
in no contacts. function is ON.
3 CW or FSK was selected 3 Select the correct voice mode. 11
instead of a voice mode.
4 The DSP TX filter 4 Adjust the settings in Menu Nos. 25, 26. 31
bandwidth was improperly
selected.
5 The wrong antenna 5 Press and hold [PRE (ANT 1/2)] to select the 50
connector (ANT 1 or ANT 2) other antenna connector.
was selected.
Attempting to transmit 1 The antenna is not 1 Check the antenna connection. Correct as 1
results in the “HELLO” connected correctly. necessary.
message appearing 2 The impedances of the 2 Reduce the SWR of the antenna system. 50
and the reception antenna and transceiver
mode being restored. are not properly matched.
3 The input voltage is outside 3 Correct the input voltage or use a 12 ~ 16 V 1
13.8 V DC ± 15% (11.7 ~ battery.
15.8 V DC).
4 The current rating of the 4 Use a DC power supply that has a current 1
DC power supply is not rating of more than 20.5 A at 13.8 V DC.
enough.
The transceiver has 1 The microphone gain is set 1 When in SSB or AM mode, increase the 13
low transmission too low. microphone gain.
power. 2 Poor antenna system 2 Check the antenna connections. Confirm that 50
connections are causing the antenna tuner is reporting a low SWR.
high SWR.
76
15 TROUBLESHOOTING

VOX does not The VOX gain is set too low. Increase the VOX gain. 30
operate.
HF/ 50 MHz Linear 1 The linear amplifier control 1 Set Menu No. 53 (HF) or 54 (50 MHz) to 1, 2, 53
amplifier does not is OFF. or 3.
operate. 2 The REMOTE connector 2 Inspect the REMOTE connector wiring and 66
wiring is wrong or faulty. correct it as necessary.
The transceiver’s 1 The air filters for the cooling 1 Contact a Kenwood authorized service —
output power fans have been congested center to clean the filters.
decreases after a with dust.
short operating time. 2 The cooling fans cannot 2 Relocate the transceiver so that air can easily —
provide enough air flow to flow through the TS-590S to keep the unit
cool the transceiver down. cooled.
You cannot access 1 Many repeaters require a 1 Review “FM REPEATER OPERATION” and 25
and use repeaters. subtone or 1750 Hz tone to select the correct frequency and type of
access. subtone.
2 Transmission and/or 2 You must transmit on the repeater’s input 25
reception frequency is frequency and receive on the repeater’s
wrong. output frequency. Refer to “FM REPEATER
OPERATION”.
Digital operation 1 Physical connections 1 Re-check all connections using this manual, 67,69
results in few or no between the transceiver, your TNC/ MCP manual, and your computer
connects or contacts computer, and TNC/ MCP hardware manual as references.
with other stations. are incorrect, or software
settings in the TNC/ MCP
are wrong.
2 Different transmission and 2 Confirm that the RIT and XIT functions are 29,31
reception frequencies are switched OFF. Confirm that you are not
being used. operating split frequency.
3 The levels between the 3 Adjust TX and RX levels using Menu Nos. 58,69
transceiver and the TNC/ 66 and 67, and level controls on your TNC/
MCP are incorrect. MCP.
4 Your transmitted signal or 4 Reorient/ relocate your antenna or increase 1
the incoming receive signal your antenna gain.
is too weak.
5 The TX delay time 5 Set the TNC/ MCP TX delay time to more —
parameter in your TNC/ than 300 ms.
MCP was incorrectly set.
Attempts at controlling 1 Problem with cable that 1 Check the cable and cable connections. 67
the transceiver with connects the PC to the
the computer have TS-590S.
failed. 2 Communication parameters 2 Use the same parameters in the terminal and 57
set in your terminal the transceiver. Check Menu Nos. 61 and
program do not match the 62.
transceiver parameters.
“TEMP-HI” appears A sensor in the transceiver Stop transmitting and let the transceiver —
and “CHECK” in detected high temperature. cool down for a while. Contact a Kenwood
Morse code sounds. authorized service center to clean the internal air
filters.
Transmission The voltage of the DC power Adjust the DC power supply voltage to 1
suddenly stops. supply is too high. 13.8 V DC.
“DSP ERR x” appears An internal DSP error occurs. Restart the transceiver by turning the power —
(where x is a number OFF and then back ON. If the problem persists,
from 0 ~ 3). consult Kenwood authorized Service Center.
“VGS ERR” appears. An internal error occurred in Confirm that the connector of the VGS-1 is 71
the VGS-1. securely connected to the transceiver, then
turn the transceiver power OFF and ON. If the
problem persists, contact a Kenwood authorized
service center for repairs.
77
15 TROUBLESHOOTING

A message cannot be There is a communication Confirm that the connector of the VGS-1 is 71,78
recorded/ played back error between the transceiver securely connected to the transceiver. Perform
or no announcement and the VGS-1. the Full reset. If the problem persists, contact a
can be heard. Kenwood authorized service center for repairs
(with the VGS-1 attached).
The transceiver Most of the external RF Apply a continuous single tone (1 kHz) to the —
output power seems power meters measure the microphone audio input to measure the RF
to be low in SSB average RF power. So, the output power. The PEP will be the same as this
mode. meter reading is low when RF output level.
you operate and talk in SSB
mode. The LCD meter used
in the TS-590S has relatively
fast response time but it is not
fast enough to measure the
accurate PEP (Peak Envelope
Power).
The PC and external The input terminal is different Confirm that the setting of Menu No. 63 matches 58
equipment is not from the one specified (Menu the input terminal for the external equipment.
modulating. No. 63) for the external
equipment.
MICROPROCESSOR RESET 4 Press [A/B (A=B)] to perform the VFO reset.

If your transceiver seems to be malfunctioning, • A confirmation message appears when
resetting the microprocessor to its default settings performing the VFO Reset. Press [A/B (A=B)]
may resolve the problem. There are 2 levels again to proceed. Otherwise, press any other
of resetting the microprocessor of the TS-590S key to cancel the VFO Reset and return to
transceiver: Partial Reset and Full Reset. normal operation.
• The VFOs reset to the factory default values.
INITIAL SETTINGS
FULL RESET
For each VFO, the factory defaults for the operating
frequency and mode are as follows: Perform a Full Reset if you want to erase all the data
• VFO A: 14.000.00 MHz/ USB in all the memory channels. In addition, this function
resets all the settings that you customized, to the
• VFO B: 14.000.00 MHz/ USB factory defaults (i.e.- menu settings, antenna tuner
The Memory channels and Quick Memory channels preset data, etc.).
have no data stored. 1 Turn the transceiver power OFF.
2 Press [A/B (A=B)] + [ ] to switch the transceiver
VFO RESET ON.
Perform a VFO Reset if a key or control does not • A confirmation message appears on the display.
function according to the instructions in this manual.
The following data is NOT erased by performing a 3 Turn the MULTI/CH control and select “FULL
VFO Reset. RESET”.
• Memory channel data 4 Press [A/B (A=B)] to perform the Full reset.
• Menu settings • A confirmation message appears when
• Antenna tuner preset data performing the Full Reset. Press [A/B (A=B)]
again to proceed. Otherwise, press any other
• ANT 1/ ANT 2 selection data key to cancel the Partial Reset and return to
• Frequency and mode data for the Auto Mode normal operation.
function • All frequencies, modes, memory data,
• Various adjustment setting values adjustment values, and AT preset data are set
to the factory default values.
1 Turn the transceiver power OFF.
2 Press [A/B (A=B)] + [ ] to switch the transceiver
ON.
• A confirmation message appears on the display.
3 Turn the MULTI/CH control and select “VFO
RESET”.
78
15 TROUBLESHOOTING
OPERATION NOTICES 60m BAND OPERATION (K-TYPE/ USA ONLY)

The transceiver has been designed and engineered to Effective from July 3, 2003, FCC Report and Order
avoid possible hardware glitches. However, you may (R&O) in ET Docket 02-98 granted US amateurs
notice the following symptoms when you operate the secondary access to five discrete channels in the
transceiver. These symptoms are not malfunctions. vicinity of 5 MHz. General, Advanced, and Amateur
Extra licensees may use the following five channels
DC POWER SUPPLY on a secondary basis with a maximum effective
radiated power of 50 W PEP relative to a half wave
As stated in the SPECIFICATIONS {page 80}, this dipole. Only upper sideband suppressed carrier voice
transceiver requires a supplied DC voltage source of transmissions may be used. The frequencies are
13.8 V ±15%. If you find that the transceiver cannot 5330.5, 5346.5, 5366.5, 5371.5 and 5403.5 kHz. The
be switched ON, or that it shuts OFF automatically, occupied bandwidth is limited to 2.8 kHz centered on
the DC voltage may be outside the specified range. 5332, 5348, 5368, 5373, and 5405 kHz respectively.
In such a case, remove the DC cable from the The TS-590S transceiver stops at the 60 m band as
transceiver immediately and confirm that the supplied you scroll up or down the amateur radio frequency
voltage is within the specified range. bands. For more information, contact ARRL or search
their Web site using the key word “60 meter”:
INTERNAL COOLING FAN http://www.arrl.org
The transceiver detects the temperature of the final

department regardless of the transmission and
reception state of the main body, in order to protect
the internal circuits from high temperatures. The
cooling fan speed and transmission output is controled
through the following.
• When the thermistor detects a rise in temperature
in the final department, the cooling fan turns on at
low speed. As the temperature rises, the speed of
the cooling fan increases.
• When an abnormally high temperature is detected,
the temperature protection circuit activates,
reducing the transmission output to the lowest
possible power.
When the temperature protection circuit activates,
return the transceiver to receive mode and leave the
transceiver power ON. Allow time for the cooling fan
to return the internal temperature to normal.
• If you turn the transceiver power OFF, the cooling
fan will not run and it will take much longer for the
internal temperature to decrease.
INTERNAL BEATS
On some spots of the receiver frequencies, the
S-meter moves or you cannot receive any signals.
This is inevitable when you use superheterodyne
receivers. You may notice the signals on the following
spots of the frequency:
• 15.600.00 MHz
• 31.200.00 MHz
• 46.800.00 MHz
AGC
When you turn the AGC function OFF {page 29}, the
receiving audio signals can be distorted. In this case,
decrease the RF gain, turn the pre-amplifier OFF, or
turn the attenuator ON. In general, the RF gain must
be greatly reduced when the AGC is turned OFF.
79
OPTIONAL ACCESSORIES
HS-5 HS-6 LF-30A MC-43S
Delux Headphones Small Headphones Low-pass Filter Microphone
(Upper cat-off
frequency 30 MHz)
MC-47 MC-60A MC-90 PG-20

Multi-function Microphone Desk-top Microphone DSP-compatible Desk-top DC cable (7 m/ 23 ft)
Microphone
Microphone sensitivity is low in FM mode.
PS-60 SO-3 VGS-1 SP-23

Regulated DC Power TCXO unit Voice Guide and External Speaker
Supply (22.5 A) Storage unit
SP-50B MB-430 ARCP-590/ ARHP-590

Mobile Speaker Mobile Bracket Remote control software
Download the free ARCP-590/ARHP-590 software

from the following URL:
http://www.kenwood.com/i/products/info/amateur/software
_download.html
80
SPECIFICATIONS
General
Mode J3E (LSB, USB)/ A1A (CW)/ A3E (AM)/ F3E (FM)/ F1B (FSK)
Number of memory channels 110 + 10 (Quick memory channels)
Antenna impedance 160 m ~ 6 m band 50 Ω (with built-in antenna tuner 16.7 ~ 150 Ω)
Supply Voltage DC 13.8 V±15%
Grounding method Negative ground
Transmit (max.) Less than 20.5 A
Current
Receive (no signal) Less than 1.5 A
Usable temperature range –10°C ~ +50°C (+14°F ~ +122°F)
Frequency stability without
–10°C ~ 50°C Within ±5 ppm
SO-3
Frequency stability
–10°C ~ 50°C Within ±0.5 ppm
with SO-3
Dimensions (W x H x D Projections not included) 270 x 96 x 291 mm/ 10.63 x 3.78 x 11.46 in
Weight Approx. 7.4 kg/ 16.3 lb
Transmitter
160 m band 1.8 ~ 2.0 MHz (K type)/ 1.81 ~ 2.0 MHz (E type)
5.1675 MHz (K type)
60 m band
5.25 ~ 5.45 MHz (K type)
30 m band 10.1 ~ 10.15 MHz
Frequency range 20 m band 14.0 ~ 14.35 MHz
17 m band 18.068 ~ 18.168 MHz
15 m band 21.0 ~ 21.45 MHz
12 m band 24.89 ~ 24.99 MHz
10 m band 28.0 ~ 29.7 MHz
6 m band 50.0 ~ 54.0 MHz (K-type) / 50.0 ~ 52.0 MHz (E type)
SSB/ CW/ FSK/ Max. 100 W

FM Min. 5W
Output power
Max. 25 W
AM
Min. 5W
Maximum frequency Wide Less than ±5 kHz

deviation (FM) Narrow Less than ±2.5 kHz
SSB Balanced
Modulation AM Low power
FM Reactance
160 m ~ 10 m band Less than –50 dB
Spurious emissions
6 m band Less than –60 dB
Carrier suppression (SSB) More than 50 dB
Unwanted sideband suppression
More than 50 dB
(modulation frequency 1.0 kHz)
Transmit frequency response –6 dB: 400 - 2600 Hz
81
17 SPECIFICATIONS
Transmitter
XIT shift frequency range ±9.999 kHz
Microphone impedance 600 Ω
Receiver
RX1 (1.8/ 3.5/ 7/ 14/ 21 MHz
band/ IF band width of 2.7 kHz RX2 (Other)
Circuit type or less (SSB/CW/FSK))
Double conversion Triple conversion
superheterodyne superheterodyne
Frequency range 0.03 ~ 59.999999 MHz
1st IF 11.374 MHz 73.095 MHz
Intermediate frequency 2nd IF 24 kHz 10.695 MHz
3rd IF − 24 kHz (except FM)/ 455 kHz (FM)
0.13 ~ 0.522 MHz: Less than 0.5 μV
0.522 ~ 1.705 MHz: Less than 4 μV
SSB/ CW/ FSK
1.705 ~ 24.5 MHz: Less than 0.2 μV
(S/N 10 dB)
24.5 ~ 30.0 MHz: Less than 0.13 μV
50.0 ~ 54.0 MHz: Less than 0.13 μV
0.13 ~ 0.522 MHz: Less than 6.3 μV
Sensitivity 0.522 ~ 1.705 MHz: Less than 31.6 μV
AM (S/N 10 dB) 1.705 ~ 24.5 MHz: Less than 2 μV
24.5 ~ 30.0 MHz: Less than 1.3 μV
50.0 ~ 54.0 MHz: Less than 1.3 μV
28.0 ~ 30.0 MHz: Less than 0.22 μV
FM (12 dB SINAD)
50.0 ~ 54.0 MHz: Less than 0.22 μV
0.13 ~ 0.522 MHz: Less than 5.6 μV
0.522 ~ 1.705 MHz: Less than 18.0 μV
SSB/ CW/ FSK/ AM
1.705 ~ 30.0 MHz: Less than 1.8 μV
Squelch sensitivity 50.0 ~ 54.0 MHz: Less than 1.1 μV
28.0 ~ 30.0 MHz: Less than 0.2 μV
FM
50.0 ~ 54.0 MHz: Less than 0.2 μV
SSB More than 2.2 kHz (–6 dB), Less than 4.4 kHz (–60 dB)
CW/ FSK More than 500 Hz (–6 dB), Less than 1.2 kHz (–60 dB)
Selectivity
AM More than 6.0 kHz (–6 dB), Less than 12.0 kHz (–50 dB)
FM More than 12.0 kHz (–6 dB), Less than 25.0 kHz (–50 dB)
Image Ratio More than 70 dB
Spurious response
IF Rejection More than 70 dB
Auto More than 60 dB
Notch filter attenuation
Manual More than 70 dB
Beat cancel attenuation (at 1 kHz) More than 40 dB
Audio output (8 Ω,10% distortion) More than 1.5 W
Audio output impedance (EXT.SP) 8Ω
RIT shift frequency range ±9.999 kHz
Specifications are subject to change without notice due to advancements in technology.
82
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli ve Elektronik Eşyalarda
Bazı Zararlı Maddelerin Kullanımının Sınırlandırılmasına Dair Yönetmeliğe uygun
olarak üretilmiştir.
This product complies with Directive, Number 26891 regarding "REGULATION
ON THE RESTRICTION OF THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN
ELECTRICAL AND ELECTRONIC EQUIPMENT".

TS 590 User - Manual

Uploaded by

Copyright:

Available Formats

TS 590 User - Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TS 590 User - Manual

Uploaded by

Copyright:

Available Formats

INSTRUCTION MANUAL

HF/ 50 MHz ALL MODE TRANSCEIVER

Information on Disposal of Old Electrical and Electronic Equipment

• Minimum recommended distance for an outdoor

Transmitting CW Messages ......................... 35 PROGRAM SCAN PARTIALLY SLOWED ........ 47

RECORDING MESSAGES ............................... 58 CHAPTER 16 OPTIONAL ACCESSORIES

Black (−) Red (+)

UTILIZING THE BAIL ACCESSORY CONNECTIONS

■ Keys for CW (PADDLE and KEY)

Note: Due to the functionality of the internal electronic

[21 (7)] [NB (LEV)]

[CH1 (REC)] RIT/ XIT control

While receiving, the meter serves as an S-meter to

Either “ ” or “ ” appears, depending on

Appears when the DRV terminal is enabled {page 50}.

ANT 1 and ANT 2 connectors DRV connector

3 To switch the transceiver OFF, press [ ] again.

ADJUSTING THE VOLUME SELECTING VFO A OR VFO B

SELECTING A BAND SELECTING A MODE

ADJUSTING THE SQUELCH MULTI-FUNCTION METER

Meter Name Parameters Measured

TRANSMITTING MICROPHONE GAIN

SELECTING TRANSMISSION POWER

2 Turn the MULTI/CH control counterclockwise to

4 Release Mic [PTT] to receive.

PROGRAMMING THE QUICK MENU

MENU ACCESS USING THE QUICK MENU

3 Press [Q-M.IN]/ [Q-MR] or turn the MULTI/CH

5 Press [MENU] to exit Menu mode.

Description Settings** Ref.

Description Settings** Ref.

CW Bug key function OFF/ ON

Description Settings** Ref.

Description Settings** Ref.

2 Turn the MULTI/CH control or press [M.IN]/

Available alphanumeric characters:

Note: Refer to page 23 to change the Power On message, and

3 Press [MIC (CAR)] to adjust the Microphone gain.

AM TRANSMISSION NARROW BANDWIDTH FOR FM

AUTO ZERO-BEAT CARRIER LEVEL

TX SIDETONE/ RX PITCH FREQUENCY

FM REPEATER OPERATION 6 Press [AGC/T (SEL] to turn the Tone function ON

■ Activating the Tone Function TONE FREQUENCY ID SCAN

7 While “ ” is visible, press and hold [AGC/T

• Press [SCAN (SG.SEL)] or [CLR] to stop

■ Fine Tuning RIT (RECEIVE INCREMENTAL TUNING)

2 Turn the Tuning control to select the exact

TRANSMISSION ■ Delay Time

3 Press and hold [VOX (LEV)]. ■ Data VOX

While the Data VOX function remains ON and the

2 If required, press [CL] to reset the XIT offset to 0.

4 To turn XIT OFF, press [XIT].

CUSTOMIZING TRANSMISSION SIGNAL Frequency Response Curves

CW BREAK-IN ELECTRONIC KEYER

6 Press [CLR] to exit. 4 Press [KEY (DELAY)] again to complete the

■ Invalid Break-In Operation

RISE TIME OF CW CW MESSAGE MEMORY

Reverse Keying Speed (wpm)