Scribd Logo
Upload

Welcome to Scribd!

  • 49 views

    Installation Instructions For SRW-S1 To DFGT Adapter: 1. Remove The Eight (8) Silver Philips Head

    Uploaded by

    John Slor
    The document provides 15 step-by-step instructions for installing an SRW-S1 to DFGT adapter. It details removing parts from both wheels, inserting wires from the DFGT into the adapter base, aligning and securing the adapter plate assembly using various screws, and completing the installation. The instructions include pictures and specify the type and size of screws needed at each step. It concludes by thanking the customer for choosing SimAbility and providing contact information for any questions.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Installation Instructions For SRW-S1 To DFGT Adapter: 1. Remove The Eight (8) Silver Philips Head

    Uploaded by

    John Slor
    49 views4 pages
    The document provides 15 step-by-step instructions for installing an SRW-S1 to DFGT adapter. It details removing parts from both wheels, inserting wires from the DFGT into the adapter base, aligning and securing the adapter plate assembly using various screws, and completing the installation. The instructions include pictures and specify the type and size of screws needed at each step. It concludes by thanking the customer for choosing SimAbility and providing contact information for any questions.

    Original Title

    SRW-DFGT_Instructions

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides 15 step-by-step instructions for installing an SRW-S1 to DFGT adapter. It details removing parts from both wheels, inserting wires from the DFGT into the adapter base, aligning and securing the adapter plate assembly using various screws, and completing the installation. The instructions include pictures and specify the type and size of screws needed at each step. It concludes by thanking the customer for choosing SimAbility and providing contact information for any questions.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    49 views4 pages

    Installation Instructions For SRW-S1 To DFGT Adapter: 1. Remove The Eight (8) Silver Philips Head

    Uploaded by

    John Slor
    The document provides 15 step-by-step instructions for installing an SRW-S1 to DFGT adapter. It details removing parts from both wheels, inserting wires from the DFGT into the adapter base, aligning and securing the adapter plate assembly using various screws, and completing the installation. The instructions include pictures and specify the type and size of screws needed at each step. It concludes by thanking the customer for choosing SimAbility and providing contact information for any questions.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    www.SimAbility.

    com
    [email protected]

    Installation Instructions for SRW-S1 to DFGT Adapter

    1. Remove the eight (8) silver Philips head


    screws holding the base halves together.

    2. Carefully remove the top half of the base.

    3. Unplug the 6-pin steering button connector


    shown here.

    You just simply need to unplug it from the circuit


    board and set it aside. Leaving it connected,
    even with the stock wheel and button's circuit
    board removed, can produce electrical noise
    triggering ghost button presses.

    4. Remove the thirteen (13) screws from the


    back side of the wheel. (9 shown in the image,
    with 4 on the bottom spoke hidden from this
    view)
    5. Carefully remove the button face from the
    wheel rim and then the connector from the
    circuit board.

    6. Remove the four (4) screws attaching the


    wheel rim to the base.

    7. Remove the stock wheel rim and gently push


    the DFTG wires into the hollow DFGT shaft.

    8. Align and then install the base puck.

    There is a circular mark on the base puck


    representing the bottom of the puck. Line that
    mark up with the bottom of the DFGT shaft,
    which is identified by the narrower gap between
    the screw bosses.
    9. Install the four (4) #10 x 1.25” (32mm) self-
    taping screws ensuring the base puck tightens
    down flat onto the base shaft.

    #10 x 1.25" (32mm) self-taping screws

    10. Extract the seven (7) stock SRW-S1 screws.

    Note: These are the only screws holding the


    SRW-S1 faceplate to its paddle base. If you allow
    the two to separate, buttons will escape.

    11. Install the adapter plate assembly as shown.

    12. Install the seven (7) 2.2mm x 25mm stainless


    self-taping screws.

    13. Optional. You can use the provided cable ties


    to attach the SRW-S1 USB cable to the adapter
    can as shown. (shown in yellow)

    2.2mm x 25mm stainless self-taping screws


    14. Slide the adapter assembly over the adapter
    puck being sure to align the keys.

    Note: Once the adapter is lined up correctly, you


    will be able to see the threaded holes in base
    puck through the holes in the adapter. You can
    rock the adapter from side to side just slightly to
    help reposition and align the adapter if needed.

    15. Install the six (6) #8 x 1/2” (12.7mm) flat-


    head hex screws through the adapter and into
    the base puck. (3/32” hex wrench included)

    Caution: The screws just need to be snug. Do not


    over tighten.

    #8 x 1/2” (12.7mm) flat-head hex screws

    Thanks for choosing SimAbility. Please contact me if you have any questions, issues, or suggestions. I'd
    like to hear from you.

    Glenn Sidman
    www.SimAbility.com
    [email protected]

    You might also like