504164-003 X-32 sn53095-53100 C.PS

ERVICE & PARTS MANUAL
POWERED ACCESS
WARNING
The X32 Machine has been re-assessed to ensure
compliance to the Machinery Directive (2006/42/EC).
The Machine rating has been changed from:
Windspeed rating of 12.5 m/s (Beaufort 6)
To
Windspeed rating of 7 m/s (Beaufort 4)
Please attach to the front cover of

your X32 manual 510329-000
X26-32
WORK PLATFORM
X 26-32
Serial Numbers 53095 – 53100
ENGLISH
When contacting Upright for service or parts information, be sure to include the MODEL and SERIAL NUMBERS from the
equipment nameplate. Should the nameplate be missing, the SERIAL NUMBER is also stamped on top of the chassis
above the front axle pivot.
Stamped Serial Number

Estampille de numéro de série
Eingestanzte Seriennummer
PART NUMBER : 504164-003
X26 SERIAL NUMBER : 50906
X32 SERIAL NUMBER : 50322
FOREWORD
HOW TO USE THIS MANUAL

This manual is divided into six sections.
S ECTION 1 I NTRODUCTION
General description and machine specifications.
S ECTION 2 O PERATION AND S PECIFICATION
Information on how to operate the work platform and how to prepare it for operation.
S ECTION 3 M AINTENANCE
Preventative maintenance and service information.
S ECTION 4 TROUBLESHOOTING
Causes and solutions to typical problems.
S ECTION 5 S CHEMATICS
Schematics and valve block diagram with description and location of components.
S ECTION 6 I LLUSTRATED P ARTS B REAKDOWN
Complete parts lists with illustrations.
SPECIAL INFORMATION
! D A N G E R !
Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
! W A R N I N G !
Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
! C A U T I O N !
Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
NOTE: Gives helpful information.
Page i
Foreword -
WORKSHOP PROCEDURES
All information contained in this manual is based on the latest product information available at
the time of printing. We reserve the right to make changes at any time without notice.
No part of this publication may be reproduced, stored in retrieval system, or transmitted, in any
form by any means, electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of the publisher. This includes text, figures and tables.
! C A U T I O N !
Detailed descriptions of standard workshop procedures, safety principles
and service operations are not included.
Please note that this manual does contain warnings and cautions against
some specific service methods which could cause personal injury or could
damage a machine or make it unsafe.
Please understand that these warnings cannot cover all conceivable ways in
which service, whether or not recommended by UpRight, might be done, or
of the possible hazardous consequences of each conceivable way, nor could
UpRight, investigate all such ways.
Anyone using service procedures or tools, whether or not recommended by
UpRight, must satisfy themselves thoroughly that neither personal safety
nor machine safety will be jeopardized.
Page ii
Section 1
INTRODUCTION
1.1 INTRODUCTION
P URPOSE
The purpose of this service and parts manual is to provide instructions and illustrations for the
operation and maintenance of this work platform manufactured by UpRight.
S COPE
The manual includes procedures for proper operation, maintenance, adjustment, and repair of
this product as well as recommended maintenance schedules and troubleshooting.
1.2 GENERAL DESCRIPTION

The work platform consists of the platform, controller, elevating assembly, power module, control
module, and chassis.
! W A R N I N G !
DO NOT use the work platform without guardrails properly assembled and in
place.
Figure 1-1: X26-32
P LATFORM 1.Platform 1
2.Platform Controller
The platform has a reinforced steel Assembly 2
floor, 1.1m (43.5 inch) high guardrails 3.Chassis Controls
with midrail, 152 mm (6 inch ) toe- 4.Chassis
5.Elevating Assembly
boards, and an entry chain at the rear of
the platform. The guardrails can be
folded down for access through doors or
for shipment.
P LATFORM C ONTROLLER
The platform controller contains the
controls to operate the machine. It is
located at the front of the platform cage.
5
A complete explanation of control func-
tions can be found in Section 2.
4
E LEVATING A SSEMBLY 3
The platform is raised and lowered by
the elevating assembly. The hydraulic
pump, driven by the engine, powers the cylinder. Solenoid operated valves control raising and
lowering.
Page 1-1
Introduction 1.2 - General Description
C HASSIS
The chassis is a structural frame that supports all the components of the X26-32 work platform.
P URPOSE OF E QUIPMENT
The objective of the work platform is to provide a quickly deployable, self-propelled, variable
height work platform to elevate personnel and materials to overhead work areas.
S PECIAL L IMITATIONS
Travel with the platform raised is limited to a creep speed range.
Elevating of the work platform is limited to firm, level surfaces only.
Any degree of slope greater than 3° will sound a warning alarm when the machine is elevated.
! D A N G E R !
The elevating function shall ONLY be used when the work platform is level
and on a firm surface.
The work platform is NOT intended to be driven over uneven, rough, or soft
terrain when elevated.
Page 1-2
2. OPERATION MANUAL
WARNING
All personnel shall carefully read, understand and follow all safety rules and operating
instructions before operating or performing maintenance on any UpRight aerial work platform.
Safety Rules
Electrocution Hazard Tip Over Hazard Collision Hazard Fall Hazard
NEVER elevate the platform or drive NEVER position the platform NEVER climb, stand, or sit on
THIS MACHINE IS NOT the machine while elevated unless the without first checking for overhead platform guardrails or midrail.
INSULATED! machine is on a firm, level surface. obstructions or other hazards.
USE OF THE AERIAL WORK PLATFORM: This aerial work platform is intended to lift persons and his tools as well as the material
used for the job. It is designed for repair and assembly jobs and assignments at overhead workplaces (ceilings, cranes, roof structures,
buildings etc.). All other uses of the aerial work platform are prohibited!
THIS AERIAL WORK PLATFORM IS NOT INSULATED! For this reason it is imperative to keep a safe distance from live parts of elec-
trical equipment!
Exceeding the specified permissible maximum load is prohibited! See “Special Limitations” on page 4 for details.
The use and operation of the aerial work platform as a lifting tool or a crane (lifting of loads from below upwards or from up high on
down) is prohibited!
NEVER exceed the manual force allowed for this machine. See “Special Limitations” on page 4 for details.
DISTRIBUTE all platform loads evenly on the platform.
NEVER operate the machine without first surveying the work area for surface hazards such as holes, drop-offs, bumps, curbs, or debris;
and avoiding them.
OPERATE machine only on surfaces capable of supporting wheel loads.
NEVER operate the machine when wind speeds exceed this machine’s wind rating. See “Beaufort Scale” on page 4 for details.
IN CASE OF EMERGENCY push EMERGENCY STOP switch to deactivate all powered functions.
IF ALARM SOUNDS while platform is elevated, STOP, carefully lower platform. Move machine to a firm, level surface.
Climbing up the railing of the platform, standing on or stepping from the platform onto buildings, steel or prefab concrete structures, etc.,
is prohibited!
Dismantling the swing gate or other railing components is prohibited! Always make certain that the swing gate is closed and securely
locked!
It is prohibited to keep the swing gate in an open position (held open with tie-straps) when the platform is raised!
To extend the height or the range by placing of ladders, scaffolds or similar devices on the platform is prohibited!
NEVER perform service on machine while platform is elevated without blocking elevating assembly.
INSPECT the machine thoroughly for cracked welds, loose or missing hardware, hydraulic leaks, loose wire connections, and damaged
cables or hoses before using.
VERIFY that all labels are in place and legible before using.
NEVER use a machine that is damaged, not functioning properly, or has damaged or missing labels.
To bypass any safety equipment is prohibited and presents a danger for the persons on the aerial work platform and in its working
range.
NEVER charge batteries near sparks or open flame. Charging batteries emit explosive hydrogen gas.
Modifications to the aerial work platform are prohibited or permissible only at the approval by UpRight.
AFTER USE, secure the work platform from unauthorized use by turning both keyswitches off and removing key.
The driving of MEWPs on the public highways is subject to regulations made under the Road Traffic Acts.
Page 1
504164-002
C ONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Special Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Platform Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Manual Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Beaufort Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Lift Overload Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Pre-Operation Safety Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
System Function Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Platform Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Travel With the Platform Lowered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Elevating the Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Travel With the Platform Elevated. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lowering the Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Emergency Lowering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
X26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
X32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lower the Guardrails, X26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lowering Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Raising Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fold Down guardrails, X32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Fold Down Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Erection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Towing or Winching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Parking Brake Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
After Use Each Day. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hour Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Transporting the Work Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Preparation for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Lifting By Crane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
By Forklift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Driving or Winching onto a Truck or Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Blocking The Elevating Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Scissor Brace Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Scissor Brace Stowage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Battery Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Inspection and Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Daily Preventative Maintenance Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Page 2 Operation Manual

Introduction 504164-002
I NTRODUCTION
This manual covers operation of the X 26-32 Self-Propelled Work Platforms.
This manual must be stored on the machine at all times.
G ENERAL D ESCRIPTION
! W A R N I N G !
DO NOT use the maintenance platform without guardrails properly assembled and in place
Figure 1: X 26-32
1. Platform
2. Elevating Assembly
3. Chassis
4. Power Module
5. Control Module
6. Platform Controls
7. Manual Case
8. Chassis Controls
9. Hydraulic Fluid Reservoir
10. Batteries
Operation Manual Page 3

504164-002 Special Limitations
S PECIAL L IMITATIONS
Travel with the platform raised is limited to creep speed range.
Elevating the Work Platform is limited to firm, level surfaces only.
! D A N G E R !
The elevating function shall ONLY be used when the work platform is level and on a firm surface.
The work platform is NOT intended to be driven over uneven, rough, or soft terrain.
PLATFORM CAPACITY
The maximum capacity for the MACHINE, including occupants is determined by model and options, and
is listed in “Decals” on page 18.
! D A N G E R !
DO NOT exceed the maximum platform capacity or the platform occupancy limits for this machine.
MANUAL FORCE
Manual force is the force applied by the occupants to objects such as walls or other structures outside the
work platform.
The maximum allowable manual force is limited to 200 N (45 lbs.) of force per occupant, with a maximum
of 400 N (90 lbs.) for two or more occupants.
! D A N G E R !
DO NOT exceed the maximum amount of manual force for this machine.
BEAUFORT SCALE
Never operate the machine when wind speeds exceed 25 km/h (15 mph) [Beaufort scale 4].
BEAUFORT WIND SPEED
RATING GROUND CONDITIONS
m/s km/h ft/s mph
3 3,4~5,4 12,25~19,4 11.5~17.75 7.5~12.0 Papers and thin branches move, flags wave.
4 5,4~8,0 19,4~28,8 17.75~26.25 12.0~18 Dust is raised, paper whirls up, and small branches sway.
5 8,0~10,8 28,8~38,9 26.25~35.5 18~24.25 Shrubs with leaves start swaying. Wave crests are apparent in ponds or swamps.
6 10,8~13,9 38,9~50,0 35.5~45.5 24.5~31 Tree branches move. Power lines whistle. It is difficult to open an umbrella.
7 13,9~17,2 50,0~61,9 45.5~56.5 31.~38.5 Whole trees sway. It is difficult to walk against the wind.
LIFT OVERLOAD ALARM

If a load equivalent to 90% of safe working load is lifted a fault code “03” will be displayed on the digital
display on the platform control box. If a load which is greater than the safe working load is present in the
basket all machine functions will cease to operate and an acoustic warning will sound. In order to return to
normal operation a load equal to or less than the safe working load must be present in the basket and the
power must be re-cycled, power can be re-cycled by pushing the emergency stop button and releasing it
again.
! D A N G E R !
Never operate the machine with a platform load greater than the rated capacity.

Controls and Indicators 504164-002
C ONTROLS AND I NDICATORS

Figure 2: Controls and Indicators
Platform Controls
1 Drive Selectors
2. Horn Button 2 5
3. Lift/Lower Button
4. Emergency Stop Button
5. Display
6. Joystick
Chassis Controls
1 2 3 4
1. Keyswitch
2. Enable Button
3. Toggle Switch (Up & Down)
4. Emergency Stop Switch

504164-002 Pre-Operation Safety Inspection
P RE -O PERATION S AFETY I NSPECTION

NOTE: Carefully read, understand and follow all safety rules, operating instructions, labels and National Safety
Instructions/Requirements. Perform the following steps each day before use.
1. Open modules and inspect for damage, fluid leaks or missing parts.
Figure 3: Hydraulic Tank
2. Check the level of the hydraulic fluid with
the platform fully lowered. The hydraulic
reservoir is located in the Control Mod-
ule Door. The fluid level must be
between the MIN and MAX lines. Add
hydraulic fluid if necessary.
3. Check that fluid level in the batteries is
correct.
4. Verify that batteries are charged.
5. Check that A.C. extension cord has
been disconnected from the plug in the
rear of the machine.
6. Check that all guardrails are in place
and all fasteners are properly tightened.
7. Inspect the machine thoroughly for
cracked welds and structural damage,
loose or missing hardware, hydraulic
leaks, damaged control cable, loose wire connections and wheel bolts.

System Function Inspection 504164-002
S YSTEM F UNCTION I NSPECTION

Refer to Figure 2 for the locations of various controls and indicators.
! W A R N I N G !
STAND CLEAR of the work platform while performing the following checks.
Before operating the work platform, survey the work area for surface hazards such as holes, drop-offs,
bumps and debris.
Check in ALL directions, including above the work platform, for obstructions and electrical conductors.
Protect the control console cable from possible damage while performing checks.
1. Move the machine, if necessary, to an unobstructed area to allow for full elevation.
2. Pull Chassis Emergency Stop Switch to the ON position.
3. Pull Platform Emergency Stop Switch to the ON position.
4. Turn and hold the Chassis Key Switch to the ON position. Push the Chassis Lift/Lower Switch to the UP
position and raise the platform approximately 2,1 m (7 feet). BLOCK THE ELEVATING ASSEMBLY AS
DESCRIBED ON PAGE 9.
5. Visually inspect the elevating assembly, lift cylinder, cables, and hoses for cracked welds and structural
damage, loose hardware, hydraulic leaks, loose wire connections, and erratic operation. Check for miss-
ing or loose parts.
6. Verify that the Depression Mechanism Supports have rotated into position under the machine. REMOVE
THE SCISSOR BRACE AS DESCRIBED ON page 13.
7. Push the Chassis Lift/Lower Switch to the UP position and fully elevate the platform.
8. Partially lower the platform by pushing Chassis Lift/Lower Switch to LOWER, and check for proper oper-
ation of the audible lowering alarm.
9. Open the Emergency Lowering Valve (see Figure 5) by pulling the knob out to check for proper opera-
tion. When the platform is lowered, release the knob.
10. Push the Chassis Emergency Stop Switch to check for proper operation. All machine functions should
be disabled. Pull out the Chassis Emergency Stop Switch to resume.
11. Check that the route is clear of obstacles (persons, obstructions, holes, and drop-offs, bumps and
debris), is level, and is capable of supporting the wheel loads.
12. Mount the platform and properly close the entrance.
13. Mount the platform and select DRIVE mode.
NOTE: Use both HI and LOW drive (if applicable) when performing the following step.
14. While engaging the Interlock Switch, move the Control Handle to FORWARD, then REVERSE, to check
for speed control.
15. Push the Steering Switch RIGHT, then LEFT, to check for steering control.
16. Select LIFT mode. Grasp the Control Handle, engaging the Interlock Switch, and push it forward to
check platform lift controls. Raise the platform to full elevation.
17. Pull back on the Control Handle. The platform should descend and the audible lowering alarm should
sound.
18. Push the Platform Emergency Stop Switch to check for proper operation. All machine functions should
be disabled. Pull out the Platform Emergency Stop Switch to resume.

504164-002
O PERATION
Before operating the work platform, ensure that the Pre-Operation Safety Inspection has been completed
and that any deficiencies have been corrected. Never operate a damaged or malfunctioning machine.
The operator must be thoroughly trained on this machine.
PLATFORM EXTENSION
Figure 4: Platform Extension

2. Depress the foot lever located at the rear of the platform
extension. Push the platform extension forward until the
pin engages the front stop.
3. To retract the platform extension, depress the foot lever
and pull the platform extension toward the rear of the
machine until the pin engages the rear stop.
TR A V E L W I T H THE PLATFORM
LOWERED
1. Check that the route is clear of obstacles (persons,
obstructions, holes, drop-offs, bumps, and debris), is level,
and is capable of supporting the wheel loads.
2. Verify that the Chassis Key Switch is turned to ON and the
Chassis Emergency Stop Switch is ON (pulled out).
4. Check clearances above, below, and to the sides of platform.
5. Pull the Platform Emergency Stop Switch out to the ON position.
6. Select DRIVE mode.
NOTE: Choose between standard drive and extra torque depending on the gradient.
7. Engage the Interlock Switch and move the Control Handle to FORWARD or REVERSE to travel in the
desired direction. The speed of the machine will vary depending on how far from centre the Control
Handle is moved.
STEERING
1. Turn the Drive/Lift Switch to DRIVE.
2. While engaging the Interlock Switch, push the Steering Switch to RIGHT or LEFT to turn the wheels in
the desired direction. Observe the tires while manoeuvring the work platform to ensure proper direction.
NOTE: Steering is not self-centring. Wheels must be returned to the straight ahead position by operating the Steering
Switch.
ELEVATING THE PLATFORM

1. Select a firm, level surface.
2. Select LIFT mode.
3. While engaging the Interlock Switch, push the Control Handle forward.
4. If the machine is not level the tilt alarm will sound and the machine will not lift or drive. If the tilt alarm
sounds the platform must be lowered and the machine moved to a firm level surface before
attempting to re-elevate the platform.
NOTE: Depression Mechanism supports will deploy automatically as the platform elevates and will retract after the
platform has been lowered completely and has been driven.

Operation 504164-002
TR A V E L W I T H THE PLATFORM ELEVATED

NOTE: The machine will travel at reduced speed when the platform is elevated.
1. Check that the route is clear of obstacles (persons, obstructions, holes, drop-offs, bumps, and debris), is
level, and is capable of supporting the wheel loads.
2. Check clearances above, below, and to the sides of platform.
3. Select DRIVe mode.
4. Engage the Interlock Switch and move the Control Handle to FORWARD or REVERSE to travel in the
desired direction. The speed of the machine will vary depending on how far from centre the Control Han-
dle is moved.
5. If the machine is not level the tilt alarm will sound and the machine will not lift or drive. If the tilt alarm
sounds the platform must be lowered and the machine moved to a firm, level surface before
attempting to re-elevate the platform.
LOWERING THE PLATFORM

1. Select LIFT mode.
2. Check around the base of the platform to ensure that no one is in contact with the machine. Engage the
Interlock Switch and pull back on the Control Handle to lower the platform.
3. The platform will stop when it reaches the PPE cutout height. Inspect around the machine to ensure no
one is in contact with the machine. After a four-second time delay, lower the platform as in step 2.
EMERGENCY LOWERING
Figure 5: Emergency Lowering Valve
! W A R N I N G !
If the platform should fail to lower, NEVER climb
down the elevating assembly.
Stand clear of the elevating assembly while operating Emergency Lowering Knob
the Emergency Lowering Valve Knob.
X 26
X26
The Emergency Lowering Valve for the X26 is
located at the rear of the machine, above the
charger.
1. Open the Emergency Lowering Valve by pulling
and holding the knob.
2. To close, release the knob. The platform will not
elevate if the Emergency Lowering Valve is open.
X32
The emergency lowering control switch is located at
Emergency Lowering Button
the rear of the machine.
1. Open the emergency lowering valve by pushing
down on the toggle switch and holding it.
2. Once the platform is fully lowered, release the
toggle switch to close the valve. The platform will
not elevate if the Emergency Lowering Valve is
open. X 32

504164-002 Operation
LOWER THE G U A R D R A I L S , X26

This procedure applies only to the X26 model for the purpose of passing through a standard double door-
way. Guardrails must be returned to proper position before using the machine.
LOWERING PROCEDURE
1. Ensure that the slide-out deck extension is fully retracted and the deck pin is locked. Place the Platform
Controls on the floor of the platform.
2. Remove and retain the set screws from the side guardrails and the slide-out deck guardrails.
3. Lower the slide-out deck guardrail completely.
4. Lower the rear guardrail until it rests on the stop screws.
5. Lower the side guardrails completely.
6. Raise the rear guardrail until the retaining pins engage. Remove and retain the stop screws and nuts
from the rear guardrail.
7. Pull the two retaining pins and lower the rear guardrail completely.
RAISING PROCEDURE
1. Raise the rear guardrail until the retaining pins engage.
2. Install the stop screws and nuts on the rear guardrail and torque to 42 N-m (31 ft. lbs).
3. Pull the two retaining pins and lower the rear guardrail until it rests on the stop screws.
4. Raise the side guardrails until the tops are level with the rear guardrail.
• Install the set screws
5. Raise the slide-out deck guardrail until the top is level with the side guardrails.
• Install the set screws
6. Hang the controller on the slide-out deck guardrail.
7. Torque all set screws to 42 N-m (31 ft. lbs).
! W A R N I N G !
Before operating machine, guardrails must be securely fastened in their proper position.
FOLD DOWN GUARDRAILS, X32

This procedure applies only to the X32 model for the purpose of passing through a standard double door-
way. Guardrails must be returned to proper position before using the machine.
FOLD DOWN PROCEDURE

1. Unhook the controller from the side guardrail and place it on the floor of the platform.
2. Pull the retaining pin on the front guardrail and rotate inwards.
3. Pull the retaining pin on the rear guardrail and rotate inwards.
4. Starting with the slide-out deck guardrails and then the outer guardrails, lift up on each guardrail and
fold inward.
ERECTION PROCEDURE
1. Starting with the outer guardrails and then the slide-out deck guardrails, raise each guardrail and drop it
down, securing it in the vertical position.
2. Rotate the front and rear upper guardrails outward and secure them to the opposite side guardrails,
using the retaining pins.
3. Hang the controller on the side guardrail.

Towing or Winching 504164-002
TOWING OR W INCHING
Perform the following only when the machine will not operate under its own power and it is necessary to
move the machine or when winching onto a transport vehicle (see “Transporting the Work Platform” on
page 11).
C A U T I O N
DO NOT tow or winch the machine faster than 0,3 m/s (1 ft./s). Faster speeds will damage drive
components and void the warranty.
! W A R N I N G !
Never tow faster than 0,3 m/sec. (1 ft./sec.).
Never operate the work platform with the parking brakes released. Serious injury or damage could
result.
AFTER USE EACH DAY

1. Ensure that the platform is fully lowered.
2. Park the machine on a firm level surface, preferably under cover, secure against vandals, children and
unauthorized operation.
3. Turn the Chassis Key Switch to OFF and remove the key to prevent unauthorized operation.
HOUR METER
To access the hour meter function perform the following steps.
1. Climb into the basket (with the machine powered up)
2. Push the platform emergency stop button.
3. Hold down the following buttons, Jib and Upper Boom Lift.
4. While holding the buttons twist the emergency stop button to return power to the machine.
5. “hr” will now be displayed on the read-out, Pressing the right turn button will scroll through the accumu-
lated hours two digits at a time. For example, if pressing the right turn button once displays “20”, pressing it
a 2nd time displays “58”, and pressing it a 3rd time displays “hr”, the elapsed time of operation is 2058
hours.
TRANSPORTING THE WORK P LATFORM

PREPARATION FOR SHIPMENT
1. Fully lower the platform.
2. Disconnect the battery negative (-) lead from the battery terminal.
3. Band the controller to the front guardrail.
4. Band the elevating linkage to the frame.

504164-002 Transporting the Work Platform
Figure 6: Secure Crane Straps
LIFTING BY CRANE
1. Secure straps to chassis tie down/lifting lugs only.
2. Place the platform onto the transport vehicle in transport position.
3. Chock the wheels.
4. Secure the work platform to the transport vehicle with chains or
straps of adequate load capacity attached to the chassis tie down/lift-
ing lugs.
BY FORKLIFT
! D A N G E R !
Forklifting is for transport only.
See specifications for weight of work platform and be certain that forklift is of adequate capacity to lift
the work platform.
Forklift from the rear of the machine using the forklift pockets provided. If necessary, the machine may be
forklifted from the side by lifting under the Chassis Modules.
Figure 7: Transporting the Work Platform
Rear Tie Down/Lift Lugs

DRIVING OR WINCHING ONTO
A TR U C K OR TR A I L E R
NOTE: Do not winch faster than 0,3 m/s (1 ft/s).
1. Move the machine onto the truck or trailer;

A. To Drive the machine onto the transport vehicle:
a. Move the work platform up the ramp and into
transport position.
b. Set the wheels straight and turn off the machine.
c. Chock the wheels.
Forklift Pockets REAR
B. To Winch the machine onto the transport vehi-
cle:
a. Move the work platform up to the ramp. Lift Lugs
b. Attach the winch cable to the tie down/lifting
lugs.
c. Release the parking brakes (refer to “Towing or
Winching” on page 11).
d. Winch the platform into transport position
e. Chock the wheels.
2. Secure the work platform to the transport vehicle
with chains or straps of adequate load capacity
attached to the chassis tie down/lifting lugs.
Front Tie Down Lugs FRONT
C A U T I O N
Over tightening of the chains or straps attached to the Tie Down/Lifting Lugs may result in damage to
work platform.

Maintenance 504164-002
M AINTENANCE
! W A R N I N G !
Never perform service while the platform is elevated without first blocking the elevating assembly.
DO NOT stand in the elevating assembly area while deploying or storing the brace.
Figure 8: Scissor Brace
BLOCKING THE ELEVATING

ASSEMBLY
SCISSOR BRACE INSTALLATION
1. Park the work platform on a firm, level surface. Pin Rests on Brace
when in Blocking
2. Pull Chassis EMERGENCY STOP Switch to the ON position. Position
3. Pull Platform EMERGENCY STOP Switch to the ON posi-

tion.
4. Turn and hold the Chassis Key Switch to CHASSIS.
Scissor Brace in
5. Push the Chassis Lift/Lower Switch to LIFT to elevate the Rest Position
platform until the Scissor Brace can be rotated to the vertical Brace Rotates to
position. Blocking Position
6. X26 – From the rear of the machine, lift the Scissor Brace
from its stowed position. Rotate upward and outward, then
down until it is hanging vertically below its attachment point.
7. X32 – From the left side of the machine, pull the locking pin
securing the brace. Rotate the Scissor Brace counter clock-
Brace Rests on Pin
wise until it is in the vertical position. when in Blocking
Position
8. Lower the platform by pushing the Chassis Lift/Lower Switch
to LOWER and gradually lower the platform until the Scissor
Brace is supporting the platform.
SCISSOR BRACE STOWAGE

1. Using the Chassis Controls, gradually elevate the platform
until the Scissor Brace is clear.
2. X26 – Rotate the Scissor Brace outward and upward over its mounting point until it rests in the stowed
position.
3. X32 – Rotate the Scissor Brace clockwise until the locking pin engages.
4. Lower the platform by pushing the Chassis Lift/Lower Switch to LOWER to completely lower the plat-
form.

504164-002 Maintenance
BATTER Y MAINTENANCE
! W A R N I N G !
Hazard of explosive gas mixture. Keep sparks, flame, and smoking material away from batteries.
Always wear safety glasses when working near batteries.
Battery fluid is highly corrosive. Thoroughly rinse away any spilled fluid with clean water.
Always replace batteries with UpRight batteries or manufacturer approved replacements weighing
26,3 kg (58 lbs.) each.
• Check the battery fluid level daily, especially if the work platform is being used in a warm, dry climate.
• If electrolyte level is lower than 10 mm (3/8 in.) above the plates add distilled water only. DO NOT use
tap water with high mineral content, as it will shorten battery life.
• Keep the terminals and tops of the batteries clean.
• Refer to the Service Manual to extend battery life and for complete service instructions.
BATTERY CHARGING
Figure 9: Battery Charger
Charge the batteries at the end of each work

shift or sooner if the batteries have been dis- Charger Plug
charged.
! W A R N I N G !
Charge the batteries in a well ventilated area.
Do not charge the batteries when the work
platform is near a source of sparks or flames.
Permanent damage to the batteries will result if Charger
the batteries are not immediately recharged
after discharging.
Never leave the battery charger operating for more than two days.
Never disconnect the cables from the batteries when the charger is operating.
Keep the charger dry.
1. Check the battery fluid level. If the battery fluid level is lower than 10 mm (3/8 in.) above the plates add
distilled water only.
2. Connect an appropriate extension cord to charger outlet plug in Left Module Door. Plug the extension
cord into a properly grounded outlet of proper voltage and frequency.
3. The charger turns on automatically after a short delay. The LED charge indicator will illuminate. After
completion of the charge cycle the LED will blink, indicating that the charger is in a continuing mainte-
nance mode. DO NOT leave the charger plugged in for more than 48 hours, as permanent damage to
the batteries may occur.
NOTE: The battery charger circuit must be used with a GFI (Ground Fault Interrupt) outlet.
NOTE: DO NOT operate the machine while the charger is plugged in.

Inspection and Maintenance Schedule 504164-002
I NSPECTION AND M AINTENANCE S CHEDULE

The Complete Inspection consists of periodic visual and operational checks, along with periodic minor
adjustments that assure proper performance. Daily inspection will prevent abnormal wear and prolong the
life of all systems. The inspection and maintenance schedule should be performed at the specified inter-
vals. Inspection and maintenance shall be performed by personnel who are trained and familiar with
mechanical and electrical procedures.
! W A R N I N G !
Before performing preventative maintenance, familiarize yourself with the operation of the machine.
Always block the elevating assembly whenever it is necessary to perform maintenance while the
platform is elevated.
The daily preventative maintenance checklist has been designed for machine service and maintenance.
Please photocopy this page and use the checklist when inspecting the machine.
D AILY P REVENTATIVE M AINTENANCE C HECKLIST

MAINTENANCE TABLE KEY PREVENTATIVE MAINTENANCE REPORT
Y = Yes/Acceptable Date:_______________________________________
N = No/Not Acceptable Owner: _____________________________________
R = Repaired/Acceptable Model No: ___________________________________
Serial No: ___________________________________
Serviced By: _________________________________

COMPONENT INSPECTION OR SERVICES Y N R COMPONENT INSPECTION OR SERVICES Y N R
Check electrolyte level. Hydraulic Fluid Check fluid level.

Battery
Check battery cable condition. Hydraulic Pump Check for hose fitting leaks.
Check hoses for pinch or rubbing points. Hydraulic System Check for leaks.
Chassis
Check welds for cracks. Check for peeling, missing, or unreadable labels
Labels
Check the exterior of the cable for pinching, & replace.
Control Cable
binding or wear. Platform Deck
Check welds for cracks.
Controller Check switch operation. and Rails
Drive Motors Check for operation and leaks. Platform Deck
Check condition of deck.
and Rails
Elevating
Inspect for structural cracks. Tyres and Wheels Check for damage.
Assembly
Emergency Operate the emergency lowering valve and check
Lowering System for serviceability.
Entire Unit Check for and repair collision damage.

504164-002 Daily Preventative Maintenance Checklist
N OTES :

Decals 504164-002
D ECALS
These labels shall be present and in good condition before operating the work platform. Be sure to read,
understand and follow these labels when operating the work platform.

504164-002 Decals
D ECALS

Specifications 504164-002
S PECIFICATIONS
ITEM X26 X32

1,17 m x 2,21 m 1.17 m x 2.21 m
Platform Size w/ Extension
[44,25 pulg. x 87 pulg.] [44 in. x 87 in.]
Max. Platform Capacity
Standard 454 kg [1000 lb] 340 kg [750 lbs.]
on Extension 113 kg [250 lb] 113 kg [250 lbs.]
Max. No. of occupants
Standard (total) 4 personas 3 people
2 personas en el exterior
on Extension 1 persona 1 person
Height
Working Height 9,93 m [32,58 pies] 11.6 m [38.1 ft.]
Max. Platform Height 7,93 m [26 pies] 9.75 m [32 ft.]
Min. Platform Height 1,09 m [43 pulg.] 1.22 m [48 in.]
Dimensions
Weight 2153 kg [4747 lb] 2486 kg [5481 lbs.]
Overall Width 1,22 m [48 pulg.] 1.22 m [48 in.]
Overall Height 2,19 m [83,5 pulg.] 2.32 m [88.5 in.]
Overall Height, Rails Lowered 1,98 m [78 pulg.] 1.88 m [74 in.]
Overall Length, Extension In 2,35 m [92,5 pulg.] 2.35 m [92.5 in.]
Overall Length, Extension Out 3,26 m [128,5 pulg.] 3.26 m [128.5 in.]
Drivable Height 7,93 m [26 pies] 9.75 m [32 ft.]
Drive Speed
Platform Lowered 0 to 3,2 km/h [0 to 2.0 mph]
Platform Raised 0 to 1 km/h [0 to 0.62 mph]
24 Volt Battery Pack (4-220 A Hour, 6 Volt Batteries, min. wt. 28.12 kg
Energy Source
[62 lbs.] each)
Motor 24 Volt 4 Horse Power DC Electric Motor
System Voltage 24 Volt DC
Battery Charger 25 A, 110/220 V AC
Battery Duty Cycle 25% for 8 Hours
Hydraulic Tank Capacity 15 L [4 US Gallons] 19 L [5 US Gallons]
Maximum Hydraulic Pressure 207 bar [3000 psi]
Hydraulic Fluid
Normal Temperature (>32° F [0° C]) ISO #46
Low Temperature (<32° F [0° C]) ISO #32
Extreme Temperature (<0° F [-17° C]) ISO #15
One Single Stage Two Single Stage
Lift System
Lift Cylinder Lift Cylinders
Lift Speed Raise, 45 sec./Lower 40 sec. Raise, 65 sec./Lower 40 sec.
Control System Proportional Control Handle with Interlock Switch, Rotary Drive/Lift Switch,
and Red Mushroom EMERGENCY STOP Switch
Drive System Dual Front Wheel Hydraulic Motors
Tires 381 mm [15 in.] Diameter Solid Rubber, non-marking
Parking Brake Dual Spring Applied, Hydraulic Release
Turning Radius 203 mm [8 in.] Inside
Maximum Gradeability 12° [22%] 12° [22%]
Wheel Base 1.9 m [74.75 in.]
Guardrails 1.02 m [40 in.] High
Noise Level
*Specifications are subject to change without notice. Hot weather or heavy use may affect performance.
Refer to the Service Manual for complete parts and service information.
This machine meets or exceeds all applicable CE and GS machinery directive requirements.

504164-002 Specifications

Section 3
S ER VICE AND R EPAIR
I NTRODUCTION
This section contains instructions for the maintenance of the Work Platform.
Refer to the General Information section for information relevant to all UpRight work platforms.
Referring to the Operator Manual will aid in understanding the operation and function of the various
components and systems of the work platform, and help in diagnosing and repair of the machine.
! W A R N I N G !
Be sure to read, understand and follow all information in the Operation Section of this manual before
attempting to operate or perform service on any Work Platform.
! D A N G E R !
Never perform service on the work platform in the elevating assembly area while platform is elevated
without first blocking the elevating assembly.
DO NOT stand in elevating assembly area while deploying or storing brace.
504164-002 Page 3-1

Section 3 - Service & Repair
TABLE OF C ONTENTS
3-1 Supporting Elevating Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-2 Preventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-3 Preventative Maintenance Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3-4 Parts Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3-5 General Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3-6 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Battery Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3-7 Safety Ancillary Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Proximaty Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Emergency Lowering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3-8 Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Hydraulic Oil Tank And Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Hydraulic Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Cylinder valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Main Hydraulic Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Setting Hydraulic Manifold Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3-9 Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Depression Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Steering Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
3-10 Drive Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
3-11 Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Platform Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Chassis Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Page 3-2 504164-002

Section 3 - Service & Repair Supporting Elevating Assembly
3-1 S UPPORTING E LEVATING A SSEMBLY
! W A R N I N G !
Never perform service on the work platform in the elevating assembly area while platform is elevated
without first blocking the elevating assembly.
DO NOT stand in elevating assembly area while deploying or storing brace.
INSTALLATION
1. Park the Work Platform on firm level ground.
2. Verify Platform Emergency Stop Switch is ON.
3. Verify Platform Key Switch is ON.
Pin Rests on Brace
4. Press the Enable button and push Chassis when in Blocking
Position
Lift/Lower toggle Switch to UP to elevate
Platform.
5. Rotate the Scissor Brace into position.
Scissor Brace in
6. Press the Enable button and push Chassis Rest Position
Lift/Lower toggle Switch to DOWN position
and gradually lower Platform until the Scissor Brace Rotates to
Assembly is supported by the brace. Blocking Position
REMOVAL
1. Press the Enable button and push Chassis
Lift/Lower toggle Switch to UP to gradually
raise Platform until the brace can be removed.
2. Rotate the brace to the stowed position. Brace Rests on Pin when
in Blocking Position
3. Press the Enable button and push Chassis
Lift/Lower toggle Switch to DOWN position
and completely lower Platform
3-2 P REVENTATIVE M AINTENANCE

The complete inspection consists of periodic visual and operational checks, along with periodic minor
adjustments to assure proper performance. Daily inspection will prevent abnormal wear and prolong the
life of all systems. The inspection and maintenance schedule is to be performed at regular intervals.
Inspection and maintenance shall be performed by personnel who are trained and familiar with mechanical
and electrical procedures.
! W A R N I N G !
Before performing preventative maintenance, familiarize yourself with the operation of the machine.
Always block the elevating assembly whenever it is necessary to enter the scissor assembly to perform
maintenance while the platform is elevated.
The preventative maintenance table has been designed for machine service and maintenance repair.
Please photocopy the following page and use the table as a checklist when inspecting the machine for
service.
504164-002 Page 3-3

Preventative Maintenance Check List Section 3 - Service & Repair
3-3 P REVENTATIVE M AINTENANCE C HECK L IST

PREVENTATIVE MAINTENANCE KEY PREVENTATIVE MAINTENANCE REPORT
Interval Date: _______________________________________
Daily=each shift or every day
Owner:______________________________________
50h/30d=every 50 hours or 30 days
250h/6m=every 250 hours or 6 months Model No: ___________________________________
1000h/2y=every 1000 hours or 2 years
Serial No: ___________________________________
Y=Yes/Acceptable
N=No/Not Acceptable Serviced By: _________________________________
R=Repaired/Acceptable
Service Interval: ______________________________
COMPONENT INSPECTION OR SERVICES INTERVAL Y N R COMPONENT INSPECTION OR SERVICES INTERVAL Y N R

Check electrolyte level Daily Inspect for external damage, dents, loose
Daily
Check battery cable condition Daily rivets or cracks
Charge batteries Daily Elevating
Battery Assembly
Check charger condition & operation Daily
System
Check specific gravity 6m
Clean exterior 6m
Clean terminals 6m Check cables for pinch or rubbing points Daily
Check oil level Daily Check welds for cracks Daily
Chassis
Hydraulic Oil* Change Filter 6m Check component mounting for proper
6m
torque
Drain and replace oil 2y
Check for leaks Daily
Check for leaks Daily Lift Cylinder
Check for proper torque 6m
Hydraulic System Check hose connections 30d
Perform pre-operation inspection Daily
Check hoses for exterior wear 30d
Check for and repair collision damage Daily
Drive Motors Check for operation and leaks Daily Entire Unit
Lubricate 30d
Emergency Down Check procedure for Emergency Down Daily
Check fasteners for proper torque 6m
Check for fitting leaks Daily
Check for corrosion; remove and repaint 6m
Wipe clean 30d
Hydraulic Pump Check for peeling, missing, or unreadable
Check for leaks at mating surfaces 30d Labels Daily
labels & replace
Check mounting bolts for proper torque 6m
Wheels Check for loose components Daily
Controller Check condition & operation Daily
Oil pivot pins 30d
Check fasteners for proper torque Daily
Oil king pins 30d
Platform Deck & Check welds for cracks Daily
Steering System Check steering cylinder for leaks 30d
Rails Check condition of deck Daily
Check Wheel Yoke Securing Bolt and Nut 30d
Check entry way closure Daily
Check hardware & fittings for proper torque 6m
* NOTE: Use ISO #46 during summer and ISO #32 during winter.
Page 3-4 504164-002

Section 3 - Service & Repair Parts Location
3-4 P ARTS L OCATION
GATE
UPPER CONTROL BOX (UCB)
LADDER
DECK
HYDRAULIC TANK
(INSIDE LH CHASSIS DOOR)
SCISSOR STACK LOWER CONTROL PANEL (LCP)
(ON LH CHASSIS DOOR)
HYDRAULIC VALVE BLOCK

ECU
MOTOR CONTROLLER
PUMP MOTOR
TILT SENSOR
} CHASSIS
DRIVE MOTORS
504164-002 Page 3-5

General Lubrication Section 3 - Service & Repair
3-5 G ENERAL L UBRICATION

• Apply grease to each grease fitting.
G Grease
G G
Page 3-6 504164-002

Section 3 - Service & Repair Batteries
3-6 B ATTERIES
Electrical Energy for the motor is supplied by four 6 volt batteries wired in series for 24 volts DC. Proper
care and maintenance of the batteries and motor will ensure maximum performance from the work
platform.
C A U T I O N
If battery water level is not maintained, batteries will not fully charge, creating a low discharge rate.
! W A R N I N G !
Hazard of explosive gas mixture. Keep sparks, flame and smoking materials away from batteries.
Always wear safety glasses when working with batteries.
Battery fluid is highly corrosive. Thoroughly rinse away any spilled fluid with clean water.
Always replace batteries with UpRight batteries or manufacturer approved replacements.
Before disconnecting the battery negative (-) lead, make sure all switches are OFF. If ON, a spark will
occur at the ground terminal which could cause an explosion if hydrogen gas or fuel vapors are present.
BATTERY REPLACEMENT
The batteries are located in a slide-out tray in the rear
of the machine. There are four 6 volt batteries wired in
series for 24 volts DC. Battery cables must be installed
as shown in the Battery Cable Installation Diagram.
BATTER Y MAINTENANCE
Refer to Section 1: General Information for
complete battery maintenance instructions. Batteries Installed
Refer to the Operation Manual included in this

Service Manual for specific maintenance and
charging instructions.
Battery Cable Installation Diagram
504164-002 Page 3-7

Safety Ancillary Equipment Section 3 - Service & Repair
3-7 S AFETY A NCILLARY E QUIPMENT
PROXIMITY SWITCH
The Proximity Switch cuts power to the

High Speed Drive when the platform is
elevated.
The switch is located on the left side of the
chassis at the rear of the machine.
No adjustment of the switch should be
necessary.
LEVEL SENSOR
The Level Sensor is located on the

chassis of the machine
These units are sealed and pre-set

and require no recalibration or
adjustment.
Page 3-8 504164-002

Section 3 - Service & Repair Safety Ancillary Equipment
EMERGENCY LOWERING
! W A R N I N G !
If the platform should fail to lower, NEVER climb down the elevating assembly.
Stand clear of the elevating assembly while operating the Emergency Lowering Valve Knob.
X26
The Emergency Lowering Valve for the X26 is
located at the rear of the machine, above the
charger.
1. Open the Emergency Lowering Valve by pulling
and holding the knob.
2. To close, release the knob. The platform will not
elevate if the Emergency Lowering Valve is
open.
X32 X26 Emergency Lowering Knob
The emergency lowering control switch is located at

the rear of the machine.
X32 Emergency Lowering Button
1. Open the emergency lowering valve by pushing
down on the toggle switch and holding it.
Once the platform is fully lowered, release the
toggle switch to close the valve. The platform will not
elevate if the Emergency Lowering Valve is open.
504164-002 Page 3-9

Hydraulics Section 3 - Service & Repair
3-8 H YDRAULICS
H Y D R A U L I C O I L TA N K A N D F I L T E R
FLUID LEVEL
With the platform fully lowered, check the oil
level through the side of the tank. The level
should be between the “max” and “min” lines..
NOTE : Drain plug underneath tank
DO NOT fill above the MAX line on the tank.
DO NOT fill when the Platform is elevated.
OIL AND FILTER REPLACEMENT

1. Operate the work platform for 10-15
minutes to bring the hydraulic oil up to
normal operating temperature.
2. Provide a suitable container to catch the
drained oil. Hydraulic tank has a 12.9
liter (3.4 gal) capacity.
3. Remove the drain plug and allow all oil to
drain. Dispose of hydraulic fluid properly-
-contact your local oil recycler.
4. Clean magnet on drain plug and reinstall.
5. Unscrew the filter (located beside valve
block, easily accessed through the left
module) from the filter assembly.
Filler Cap
6. Apply a thin film of clean hydraulic oil to
the gasket of the replacement filter.
7. Screw the replacement filter onto the filter
head until the gasket makes contact, then
rotate the filter 3/4 of a turn further.
8. Fill the hydraulic reservoir with hydraulic oil until the oil level is between the minimum and maximum
lines on the tank. Do not fill above the maximum line on the tank. Hydraulic tank has a 12.9 liter (3.4
gal) capacity.
9. Operate all machine functions and recheck the fluid level. Add fluid if necessary.
! C A U T I O N !
The hydraulic oil may be of sufficient temperature to cause burns. Wear safety gloves and safety
glasses when handling hot oil.
Page 3-10 504164-002

Section 3 - Service & Repair Hydraulics
HYDRAULIC PUMP
The Hydraulic Pump is located in the Power Module, and is mounted on the rear of the motor.
REMOVAL
NOTE: If the hydraulic tank has not been drained, suitable means for plugging the hoses should be provided to prevent
excessive fluid loss.
1. Mark, disconnect and plug the hose assemblies.

2. Loosen the capscrews and remove the pump assembly from the motor.
INSTALLATION
1. Lubricate the pump shaft with general purpose 5
grease and attach the pump to the motor with
the capscrews.
2. Using a crisscross pattern, torque each 2
capscrew a little at a time until all capscrews 3
are torqued to 27N-m (20 ft-lbs).
3. Unplug and reconnect the hydraulic hoses.
4. Check the oil level in the hydraulic tank before
operating the work platform.
1
4
1. Inlet Hose 4. Pump Assembly

2. Outlet Hose 5. Electric Motor
3. Capscrew
504164-002 Page 3-11

MAIN HYDRAULIC MANIFOLD

Though it is not necessary to remove the manifold to perform all maintenance procedures, a
determination should be made prior to beginning as to whether or not the manifold should be removed
before maintenance procedures begin.
5
9 7 6 3 2
4 1
22
11 21
12 20
13
18 19
17
14 15
16
1. TEST PORT (1/4”) 12. CHECK VALVE (POTHOLE)

2. FITTING (1/4” - 1/4” MALE/MALE) 13. CROSS LINE RELIEF VALVE (DRIVE)
3. FITTING (1/4” - 1/4” MALE/MALE) 14. SOLENOID VALVE (DRIVE))
4. FITTING (1/4” - 1/4” MALE/MALE) 15. SOLENOID VALVE (DRIVE/LIFT)
5. FITTING (3/8” - 3/8” MALE/MALE) 16. CROSS LINE RELIEF VALVE (DRIVE)
6. FITTING (3/8” - 3/8” MALE/MALE) 17. PRESSURE RELIEF (MAIN LIFT)
7. FITTING (1/4” - 1/4” MALE/MALE WITH 1mm OROFICE) 18. SOLENOID VALVE (STEERING)
8. FITTING (3/8” - 3/8” MALE/MALE) 19. FLOW RESTRICTOR (STEERING)
9. FITTING (1/4” - 1/4” MALE/MALE) 20. RELIEF VALVE (STEERING)
10. - 21. FITTING (3/8” - 3/8” MALE/MALE)
11. FITTING (1/2” - 1/2” MALE/MALE) 22. RELIEF VALVE (MAIN)
Page 3-12 504164-002

Section 3 - Service & Repair Hydraulics
SETTING HYDRAULIC MANIFOLD PRESSURES
! W A R N I N G !
The hydraulic oil may be of sufficient temperature to cause burns. Wear safety gloves and safety glasses
when handling hot oil.
The oil in the hydraulic system is under very high pressure which can easily cause severe cuts. Obtain
medical assistance immediately if cut by hydraulic oil.
NOTE: Check the hydraulic pressures whenever the pump, manifold or relief valves have been serviced or replaced
MAIN RELIEF VALVE

1. Operate the hydraulic system 10 to 15
minutes to warm the oil.
2. Remove the cap or loosen the locknut on
CHECK VALVE (POTHOLE) MAIN RELIEF VALVE
the Main Relief Valve.
3. Install a 0-207 bar (0-3000 psi) pressure
gauge to the gauge port.
4. Turn the Chassis Keyswitch to CHASSIS
and elevate the machine fully.
5. While holding the Chassis Lift Switch to
the UP position, adjust the Main Relief
Valve until the pressure gauge reads 165
bar (2400 psi).
RELIEF VALVE
6. Release the Chassis Lift Switch. (STEERING)
CROSS LINE RELIEF
7. Replace the cap, or tighten the locknut on VALVES (DRIVE)
PRESSURE RELIEF FLOW RESTRICTOR
(STEERING)
the Lift Relief Valve, and torque to 8N-m (MAIN LIFT)
(6 ft-lbs).
8. Lower the platform.
504164-002 Page 3-13

COUNTERBALANCE VALVES
1. Operate the work platform for 10-15 minutes to bring the hydraulic oil up to normal operating
temperature.
2. Remove the gauge port cap and install the pressure gauge assembly.
3. Lift work platform and block front wheels off ground.
4. Loosen the locknuts on Counterbalance Valves.
5. With the machine fully powered up depress the DRIVE button on the upper control box, depress the
interlock lever and slowly pull the control lever to REVERSE to drive the wheels.
6. Adjust the Forward Counterbalance Valve by turning the adjustment screw until the pressure gauge
indicates 83 bar (1200 psi).
7. Slowly push the Control Lever to FORWARD to drive the wheels.
8. Adjust the Reverse Counterbalance Valve by turning the adjustment screw until the pressure gauge
indicates 83 bar (1200 psi).
9. Check the settings by slowly moving the Control Lever FORWARD, then REVERSE, checking the
gauge to ensure pressures are properly set. Re-adjust as needed.
10. Tighten locknuts on valves to 8N-m (6 ft-lbs). Remove blocks and lower work platform to ground.
11. Reconnect the red Control Cable wire to terminal #9.
12. Remove the gauge from the gauge port and re-install cap.
13. Check for proper operation of the drive system and brake.
STEERING RELIEF VALVES

1. Operate the work platform for 10-15 minutes to bring the hydraulic oil up to normal operating
temperature.
2. Install gauge in the gauge port.
3. Loosen locknut or remove cover on the Steering Relief Valve and turn adjusting screw counter-
clockwise two full turns.
4. While one person holds the Steering Switch to steer right or left, slowly turn the Steering Relief Valve
adjusting screw clockwise to increase the pressure until the gauge reads 69 bar (1000 psi).
5. Tighten locknut or replace Steering Relief Valve cover and torque to 8N-m (6 ft-lbs).
6. Remove gauge and replace cap.
Page 3-14 504164-002

Section 3 - Service & Repair Cylinders
3-9 C YLINDERS
DEPRESSION CYLINDER
REMOVAL
1. Mark and disconnect the hose
assemblies from the cylinder
fittings and immediately cap the
openings to prevent foreign
material from entering.
2. Place a support under the
depression guard.
3. Remove the circlips from the pivot
pins.
4. Remove the pivot pins while
supporting the cylinder.
5. Remove the cylinder.
REPAIR
DISASSEMBLY
1. Unscrew the head cap from the barrel, removing the head cap, piston, and shaft assembly from the
barrel tube.
2. Unscrew the piston.
3. Remove all rod wipers, U-cups, O-rings, and backup rings from the headcap, and discard.
4. Remove the piston ring and O-ring from the piston, and discard.
CLEANING AND INSPECTION

1. Wash all the metal parts in
cleaning solvent and blow dry with WIPER
filtered compressed air. CYLINDER BODY
2. Inspect all the threaded

components for stripped or PLAIN BUSHING
damaged threads.
3. Check the inside surface of the
cylinder barrel for scoring or
excessive wear.
FLANGED BUSHING CYLINDER ROD
4. Check the piston and headcaps for
scoring or excessive wear. RETAINING RING
5. Inspect the surface of the shaft for

scoring or excessive wear.
ASSEMBLY
1. Lubricate and install new rod wiper, U-cup, O-ring, and backup ring on the headcaps.
2. Install the headcap onto the shaft.
3. Install the new piston rings and O-ring on the piston. Re-install the piston.
4. Lubricate the piston seal with clean hydraulic fluid and install the shaft assembly in the cylinder barrel.
5. Install the head cap into the cylinder barrel, and tighten the head caps.
INSTALLATION
Installation is reverse of removal.
504164-002 Page 3-15

Cylinders Section 3 - Service & Repair
STEERING CYLINDER
REMOVAL
1. Mark and disconnect the hose assemblies
from the cylinder fittings and immediately cap
the openings to prevent foreign material from
3
entering.
2. Remove the cotter pins from the pivot pins. 2
3. Remove the pivot pins while supporting the
cylinder. Remove the cylinder. 4 1
REPAIR
DISASSEMBLY
1. Unscrew the head cap from the barrel, 5
removing the head cap, piston, and shaft
assembly from the barrel tube.
2. Unscrew the piston.
3. Remove all rod wipers, U-cups, O-rings, and 1. Steering Cylinder
backup rings from the headcap, and discard. 2. Steering Link
3. Pivot Pin
4. Remove the piston ring and O-ring from the 4. Bushing
piston, and discard. 5. Wheel Yoke
Cleaning and Inspection

1. Wash all the metal parts in cleaning solvent
and blow dry with filtered compressed air.
2. Inspect all the threaded components for stripped or damaged threads.
3. Check the inside surface of the cylinder barrel for scoring or excessive wear.
4. Check the piston and headcaps for scoring or excessive wear.
5. Inspect the surface of the shaft for scoring or excessive wear.
ASSEMBLY
1. Lubricate and install new rod wiper, U-cup, O-ring, and backup ring on the headcaps.
2. Install the headcap onto the shaft.
3. Install the new piston rings and O-ring on the piston. Re-install the piston.
4. Lubricate the piston seal with clean hydraulic fluid and install the shaft assembly in the cylinder
barrel.
Install the head cap into the cylinder barrel, and tighten the head caps.
I NSTALLATION
1. Position the cylinder assembly in the chassis and insert pivot pins and secure with new cotter pins.
2. Connect the hose assemblies to the fittings.
3. Operate the steering circuit several times throughout its entire range of travel to expel trapped air and
check for leaks.
Page 3-16 504164-002

Section 3 - Service & Repair Cylinders
LIFT CYLINDER
REMOVAL
3
1. Provide a suitable container to catch the hydraulic
fluid, then disconnect the hydraulic hoses.
Immediately plug hoses to prevent foreign material 2
from entering.
2. Remove emergency lowering valve cable and down
valve wires from the emergency lowering/down
valve. 1
3. Remove the cable bracket from the lift cylinder. 5

4. Remove capscrews and locknuts securing lift
4
cylinder pivot pins.
5. Remove lower pivot pin and lower cylinder to rest on
chassis.
6. Attach a suitable hoisting device and sling to the
cylinder, and remove upper pivot pin.
7. Carefully remove cylinder.
1. Lift Cylinder 4. Solenoid, Emergency
2. Pivot Pit Down
REPAIR 3. Capscrew and Lock- 5. Hose Connections
plate
Refer to Pothole / Steering Cylinder Repair on Page 14 &
15.
INSTALLATION
1. Coat both pivot pins with anti-seize compound.
2. Attach a suitable hoisting device and sling to the cylinder. Carefully position cylinder in the elevating
assembly, and install the upper pivot pin.
3. Install the capscrew and locknut.
4. Carefully lift the cylinder and align the lower mount, and install the pivot pin. Install the capscrew and
locknut securing the pivot pin.
5. Install the cable bracket. Connect the emergency lowering valve cable and down valve wires.
6. Unplug hydraulic hoses and attach to the cylinder.
7. Replace hydraulic fluid removed from lift cylinder.
8. Test with weight at rated Platform load to check system operation. Check for leaks
504164-002 Page 3-17

Drive Motors Section 3 - Service & Repair
3-10 D RIVE M OTORS

REMOVAL
1. Use a 1000Kg (one ton) capacity jack to raise the front of the machine. Position blocks under the
machine to prevent the work platform from falling if the jack fails.
2. Block the rear wheels to prevent the machine from rolling.
3. Remove the cotter pin, nut, and washer.
4. Remove the wheel.
NOTE: Before disconnecting hoses, thoroughly clean off all outside dirt around fittings. (After disconnecting hoses and
before removing from vehicle, IMMEDIATELY plug port holes.)
5. Tag, disconnect and plug the hose assemblies to prevent foreign material from entering.
6. Support the drive motor/wheel yoke assembly and remove the retaining ring at the top of the wheel
yoke pivot. Remove the drive motor/wheel assembly from the machine.
7. Remove the locknuts, flat washers, capscrews and drive motor from the wheel yoke.
INSTALLATION
2
1. Position the drive motor in the wheel
yoke and secure with cap screws, flat
washers and locknuts.
2. Install the drive motor/wheel yoke 7

assembly into the pivot bearing along 6
with the lower thrust washer, thrust
bushing, and retaining ring. 5
3. To ensure that the Wheel Yoke Assembly 1
does not fall out of the Chassis when the 4
vehicle is lifted off the ground fit a
3/8"UNC nut and a 1 1/4" long 4
bolt, screw nut onto bolt until 6mm from bolt
head.
Hand screw bolt into Chassis thread and 1. Drive Motor 3
tighten until bolt hits inner pin groove. 2. Wheel Yoke
Loosen bolt by a HALF turn of the bolt head. 3. Wheel
Whilst still holding bolt head with either 4. Cotter Pin
ratchet socket or spanner turn down the nut 5. Slotted Nut
till it hits Chassis outer casing and then 6. Shaft Key
tighten using a 9/16" spanner until nut is 7. Capscrew
tight to outer material.This is to lock the bolt 8. Locknut
in position.
4. Align the steer pin with the hole in the

steering link.
5. Remove the plugs from the hose

assemblies and connect to the drive
motor.
6. Install the shaft key, wheel, washer

and slotted nut. Torque the locknut to
102 N-m (75 ft-lbs). Install a new
cotter pin. DO NOT back-off the nut to
install cotter pin.
7. Remove blocks, lower the jack and

remove. Operate the drive system and
check for leaks.
Page 3-18 504164-002

Section 3 - Service & Repair 1 Controls
3-11 C ONTROLS
PLATFORM CONTROLS
The Proportional Controller can be disassembled to replace defective switches. See the Parts Manual for
replacement part numbers.
3
2
1. Control Box 5. Mounting Plate

2. Emergency Stop 6. Box Seal
3. Joystick 7. Circuit Board
4. Decal 8. Socket, Main Harness
504164-002 Page 3-19

1 Controls Section 3 - Service & Repair
CHASSIS CONTROLS
The chassis control assembly is
mounted on the inside of the chassis
door, to the left of the Hydraulic tank.
7 5 4 3
7
6
5
4
3 2
1. LCB Box Lid

2. LCB Box
3. Emergency Stop
4. Toggle Switch
5. Enable Button
6. Key
7. Key Switch
Page 3-20 504164-002

Section 3 - Service & Repair 1 Controls
504164-002 Page 3-21

1 Controls Section 3 - Service & Repair
Page 3-22 504164-002

Section 4
TROUBLESHOOTING
4.1 INTRODUCTION
The following section on troubleshooting provides guidelines on the types of problems users may
encounter in the field, helps determine the cause of problems, and suggests proper corrective
action.
Careful inspection and accurate analysis of the symptoms listed in the Troubleshooting Guide
will localize the trouble more quickly than any other method. This manual cannot cover all possi-
ble problems that may occur. If a specific problem is not covered in this manual, call our number
for service assistance.
Referring to Section 2.0 and 5.0 will aid in understanding the operation and function of the vari-
ous components and systems and help in diagnosing and repair of the machine.
G ENERAL P ROCEDURE
Thoroughly study hydraulic and electronic schematics in Section 5. Check for loose connections
and short circuits. Check/repair/replace each component in the Truth Table that is listed under
each machine function that does not operate properly.
Use the charts on the following pages to help determine the cause of a fault.
NOTE: Spike protection diodes at components have been left out of the charts to eliminate
confusion.
! W A R N I N G !
When troubleshooting, ensure that the work platform is resting on a firm,
level surface.
When performing any service that requires the platform to be raised, ensure
that the platform and booms are supported by a crane capable of supporting
the load.
Unplug the machine or disconnect the battery when replacing or testing the
continuity of any electrical component.
Page 4-1
Troubleshooting 4.2 - Troubleshooting
4.2 TROUBLESHOOTING
1. Verify your problem.
• Do a full function test from both the platform and chassis controls, and note all functions that
are not operating correctly.
2. Narrow the possible causes of the malfunction.
• Use the troubleshooting guide to determine which components are common to all circuits
that are not functioning correctly.
3. Identify the problem component.
• Test components that are common to all circuits that are not functioning correctly. Remem-
ber to check wires and terminals between suspect components. Be sure to check connec-
tions to battery negative.
4. Repair or replace any component found to be faulty.
5. Verify that repair is complete.
• Do a full function test from both the platform and chassis controls to verify that all functions
are operating correctly and that the machine is performing to specified values.
S PECIAL TOOLS
Following is a list of tools which may be required to perform certain maintenance procedures on
the X-Series work platforms.
• Flow Meter with Pressure Gauge
(P/N 067040-000)
• 0-69 bar (0-1000 psi ) Hydraulic Pressure Gauge with Adapter Fittings (P/N 014124-010)
• 0-207 bar (0-3000 psi) Hydraulic Pressure Gauge with Adapter Fittings (P/N 014124-030)
• Adapter Fitting (P/N 063965-002)
• Inclinometer (P/N 010119-000)
• Crimping Tool (P/N 028800-009)
• Terminal Removal Tool (P/N 028800-006)
A DJUSTMENT P ROCEDURES
Hydraulic settings must be checked whenever a component is repaired or replaced.
Remove counterbalance valves and "bench test" them if they are suspect.
Connect a pressure gauge of appropriate range to the test port located on the hydraulic mani-
fold.
Correct pressure settings are listed in the hydraulic schematic.
C HECKING P UMP P RESSURES

Remove hose from pump port and connect pressure gauge.
Page 4-2
Troubleshooting 4.3 - Troubleshooting Guide
4.3 TROUBLESHOOTING GUIDE

TROUBLE PROBABLE CAUSE REMEDY
All functions 1. Blown electric motor fuse Check 160 amp electric motor fuse. Replace if blown.
inoperable,
electric motor 2. Faulty battery Check the voltage output of the battery charger. If less than 24 VDC,
does not start. charger.
3. Faulty battery(ies). After completely charging batteries, test each battery. Replace as
4. Loose or broken Check continuity of all battery and motor leads. Replace if necessary.
battery lead.
5. Emergency Stop With emergency stop switch in the ON position, check continuity
switch(es) failed open.
6. Blown control fuse Check 7A circuit control fuse. Replace if blown.
All functions 1. Oil level in hydraulic Check hydraulic fluid level, top off as required.
inoperable. reservoir is low.
Electric motor
starts when 2. Faulty hydraulic Check pressure and delivery of the hydraulic pump. Replace if
control is pump.
actuated.
Platform will not 1. Emergency Close emergency
elevate or Lowering valve down valve.
elevates slowly. open.
2. Platform Observe maximum load rating. (see Operation section of this manual)
overloaded.
3. Faulty controller at Check functionality of controller. Replace if faulty.

upper controls.
4. Blown control fuse Check 7A circuit contrrol fuse. Replace if blown.
5. Battery level low. Check Battery Voltage. Charge if necessary.

Check for fault code 68
Platform drifts 1. Emergency Ensure that emergency lowering valve is completely closed. Replace
down after being lowering valve
elevated open.
2. Leaking piston Check for leakage at cylinder return line, replace seals if necessary.
seals in lift
cylinders
Page 4-3
Troubleshooting 4.4 - Fault Codes introduction
4.4 FAULT CODES INTRODUCTION

The X-Series is equipped with a fault detection system, if you have a faulty component, bad
electrical connection or start up error a fault code will be displayed on the read out located
on the upper control box.
For fault codes 01 - 39 the following procedure should be followed.
Ensure that no selector buttons are depressed.
Ensure that the deadman switch on the joystick is not held.
Ensure that the joystick is in neutral.
Ensure that the steer rocker is not activated.
Ensure that toggle switch is in neutral.
Then re-cycle power, do this by pushing and releasing the emergency stop button. If the
fault code is still displayed you may have a faulty upper or lower control box, consult the
error code list to identify the problem component and replace if necessary.
For fault codes 54 - 68 the following procedure should be followed.
1. Check the fault code list to identify the problem component.
2. Ensure that the wiring harness is connected, secure, in good condition and fully intact.
3. Ensure that the problem component is receiving electrical signal, consult the schematics
in section 6 of this manual to identify the ECU output and harness test points.
4. If no ECU output is present replace the ECU.
5. If ECU output is present but no signal is reaching the component replace the wiring har-
ness.
6. If signal is reaching the component but the component is not functioning replace the
component (refer to section 7 of this manual for part number information).
Page 4-4
Troubleshooting 4.5 - Fault Codes
4.5 FAULT CODES
01 – System initialization error

02 – System communication error
22 – Platform Left Turn Switch ON at power-up
23 – Platform Right Turn Switch ON at power-up
25 – Platform Hi-Drive Switch ON at power-up
27 – Platform Lo-Drive Switch ON at power-up
28 – Platform Lift Switch ON at power-up
29 – Platform Joystick Enable Switch ON at power-up
31 – Platform Joystick not in neutral at power-up
32 – Lower Control Up/DownToggle ON at power-up
39 – Lower Control Enable Switch ON at power-up
51 – Hi Speed / Low Speed Coil fault

54 – Pothole Retract Coil fault
55 – Lift Up Coil fault
56 – Lift Down Coil fault
59 – Steer Right Coil fault
61 – Steer Left Coil fault
66 – Forward Coil fault
67 – Reverse Coil fault
68 – Low Battery fault
Page 4-5
Troubleshooting 4-6 - Electric
4-6 E LECTRIC
Table 4-1: Electrical Troubleshooting Table
Depression Mechanism Retract

Depression Mechanism Extend
High Speed/Creep
Lower Platform
Lower Controls
Raise Platform
Upper Controls
Battery Charge
Drive Forward
Drive Reverse
Down Alarm
Steer Right
Tilt Alarm
Steer Left
Function
Brakes
Component
Alarm
Batteries X X X X X X X X X X X X X X
Battery Charger X
5 AMP Circuit Breaker X X X X X X X X X X X X X X
175 AMP Fuse X X X X X X X X X X X X
ECU X X X X X X X X X X X X X X
Motor Control X X X X X X X X X X X X
Motor X X X X X X X X X X
Chassis Emergency Stop Switch X X X X X X X X X X X X X X
Chassis Key Switch X X X X X X X X X X X X X X
Platform Emergency Stop Switch X X X X X X X X X X X X X X
Interlock Switch X X X X X X X X
PQ Control Handle X X X X X
Height Limit Switch X
Platform Steering Switch X X
Tilt Sensor X X X X X X X X X X X X X X
Steering Solenoid (right) X
Steering Solenoid (left) X
Platform Lift Solenoid X
Down Solenoid X
Reverse Solenoid X
Forward Solenoid X
Page 4-6
Troubleshooting 4-7 - Hydraulic
4-7 H YDRAULIC
Table 4-2: Hydraulic Troubleshooting Table
.\
Depression Mechanism Retract

Depression Mechanism Extend
Lower Platform
Drive Forward
Drive Reverse
Lift Platform
Steer Right
Steer Left
Function
Brakes
Creep
Component
Check Valve X X
Steering Cylinder X X
Lift Cylinder X
Depression Mechanism Cylinder X X
Brake Cylinder X
Suction Strainer X X X X X X X X
Return Filter X X X X X X X X
Drive Motors (2) X X
Pump X X X X X X X X
Main Relief Valve X X X X X X X
Steering Relief Valve X X
Lift Relief Valve X
Tank
Steering Right/Left Valve X X
Lift Valve X
Down/Emergency Lowering Valve X
Forward/Reverse Valve X X
Counterbalance Valve X X X X
Page 4-7
Troubleshooting 4-7 - Hydraulic
Notes :
Page 4-8
Section 5
SCHEMATICS
5.1 INTRODUCTION
This section contains electrical and hydraulic power schematics and associated information for maintenance purposes.
The diagrams are to be used in conjunction with the information in Section 4. They allow understanding of the makeup
and functions of the systems for checking, tracing, and faultfinding during troubleshooting analysis.
C ONTENTS
Electrical Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Cable Assembly (J1 Harness) . . . . . . . . . . . . . . . . . . . . . . . 5-3
Schematic (J1 Harness) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Overload Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Hydraulic Schematic (X26) . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Hydraulic Schematic (X32) . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Page 5-1
Schematics
5.2 ELECTRIC
Hydraulic Schematic
Page 5-2 504164-002

Schematics
5.3 CABLE ASSEMBLY
504164-002 Page 5-3

Schematics
5.4 J1 CABLE SCHEMATIC
+
−
+
−
Page 5-4 504164-002

Schematics
5.5 OVERLOAD SCHEMATIC
504164-002 Page 5-5

:
Page 5-6
Schematics
Lift Cylinder
Pothole Cylinder LH
M1
FWD
Pothole Cylinder RH
CT3
CT1
Steering Cylinder
5.6 Hydraulic Schematic (X26)
M3
CT2
REV M2
M4
S1 S2 L PP1 PP2 B
CT6
B A
CT5
CT9
D1
CT7
CT2
CT3
G
D2
P CT11
Filter CT4
CT10
TANK T
PUMP
504164-002
Page 5-7
Schematics
Lift Cylinder Lift Cylinder

LOWER
Pothole Cylinder LH
M1
FWD
Pothole Cylinder RH
CT3
CT1
Steering Cylinder
M3
CT2 M2
REV
M4
S1 S2 L PP1 PP2 B
CT6
B A
5.6 Hydraulic Schematic (X32)
CT5
CT9
D1
CT7
CT2
CT3
G
D2
Filter
P CT11
CT4
CT10
TANK T
PUMP
504164-002
Schematics
Page 5-8 504164-002

Section 6
ILLUSTRATED PARTS BREAKDOWN
6.1 INTRODUCTION
This section lists and illustrates the replaceable assemblies and parts of this product, as
manufactured by UpRight.
Each parts list contains the component parts for that assembly.
C ONTENTS
General Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 2 Hydraulic Assembly (X26) . . . . . . . . . . . . . . . . . . . . . . 6 - 21
Chassis Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 3 Hydraulic Assembly (X32) . . . . . . . . . . . . . . . . . . . . . . 6 - 23
Scissor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 6 Hydraulic Cylinder (Lift, Lower) . . . . . . . . . . . . . . . . . 6 - 25
Platform Assembly (X26). . . . . . . . . . . . . . . . . . . . . . . . 6 -12 Hydraulic Cylinder (Lift, Upper) . . . . . . . . . . . . . . . . . 6 - 26
Hydraulic Cylinder (Steer) . . . . . . . . . . . . . . . . . . . . . . 6 - 27
Power Module Assembly (X26 & X32). . . . . . . . . . . . . 6 -14 Hydraulic Cylinder (Pothole) . . . . . . . . . . . . . . . . . . . . 6 - 28
Control Module Assembly (X26 & X32). . . . . . . . . . . . 6 -15 Electrical Assembly (X26) . . . . . . . . . . . . . . . . . . . . . . 6 - 19
Control Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . 6 -16 Electrical Assembly (X32) . . . . . . . . . . . . . . . . . . . . . . 6 - 30
Lower Control Box Assembly . . . . . . . . . . . . . . . . . . . . 6 -17 Overload Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 31
Hydraulic Tank Assembly . . . . . . . . . . . . . . . . . . . . . . . 6 -18 Decal Asembly (X26) . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 33
Upper Control Box Assembly . . . . . . . . . . . . . . . . . . . . 6 -19 Decal Asembly (X32) . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 34
Hydraulic Block Assembly (Series / Parallel) . . . . . . . . 6 -20
504164-002 Page 6-1

Illustrated Parts Breakdown - General Assembly
General Assembly
504000-000 (X26)
Item Part Description QTY.
1 504001-000 CHASSIS ASSEMBLY 1

2 504002-000 SCISSOR ASSEMBLY 1
3 504003-000 PLATFORM ASSEMBLY 1
4 504007-000 HYDRAULIC ASSEMBLY 1
5 504008-000 ELECTRICAL ASSEMBLY 1
1
504200-000 (X32)
1 504201-000 CHASSIS ASSEMBLY 1

2 504202-000 SCISSOR ASSEMBLY 1
3 504203-000 PLATFORM ASSEMBLY 1
4 504207-000 HYDRAULIC ASSEMBLY 1
5 504208-000 ELECTRICAL ASSEMBLY 1
1
2
Page 6-2 504164-002

Illustrated Parts Breakdown - Chassis Assembly X26 & X32
Chassis Assembly X26 & X32

504001-000 (X26) & 504201-000 (X32)
ITEM PART NUMBER DESCRIPTION QTY ITEM PART NUMBER DESCRIPTION QTY
1 066750-000 CHASSIS WELDMENT 1 20 504143-001 SPACER, STEERING BOSS 4

2 114058-000 WHEEL YOKE / MOTOR MOUNT (RHS) 1 21 505045-000 SPACER, BELL CRANK 2
3 114057-000 WHEEL YOKE / MOTOR MOUNT (LHS) 1 22 503672-001 BUSHING, STEERING CYLINDER 1
4 066151-001 STEERING LINK (RHS) 1 23 503673-001 BUSHING, STEERING LINK 4
5 066152-001 STEERING LINK (LHS) 1 24 504155-000 WEAR PAD (STEERING LINK) 2
6 066069-002 BELL CRANK WELDMENT 1 25 065733-000 WASHER (KING PIN) 2
7 502171-000 WHEEL HUB (FRONT) 2 26 503673-000 BUSHING, BELL CRANK PIVOT PIN 1
8 502170-000 WHEEL 2 27 502152-000 SPLIT PIN 4
9 504150-000 WEAR PAD (BELL CRANK) 2 28 066307-001 LADDER 1
10 504154-000 PIVOT PIN (BELL CRANK) 1 29 066731-025 LADDER BRACKET 2
11 504144-000 BUSHING 4 30 066774-030 LADDER STAND (RHS) 1
12 504153-000 PIVOT PIN, STEERING CYLINDER (ROD END 1 31 066774-031 LADDER STAND (LHS) 1
13 114055-000 MOTOR, HYDRAULIC 2 32 502171-003 WHEEL HUB, REAR 2
14 504148-000 HYDRAULIC CYLINDER (STEERING) 1 33 504157-000 ROLLER BEARING 4
15 504033-000 COVER, TILT SENSOR 1 34 502097-000 SPACER, PAINTED 4
16 503761-000 WASHER 2 35 503755-000 CASTLE NUT 2
17 503689-000 MOUNTING BRACKET, LIMIT SWITCH 1 36 504158-000 DUST SEAL 2
18 503755-000 CASTLE NUT 4 37 502170-000 WHEEL 2
19 504167-000 PIVOT PIN, STEERING CYLINDER (BODY END) 1 38 504159-000 GREASE SEAL 2
39 011254-010 Bolt 3/8"UNC X 1 1/4" 2
40 011250-006 NUT 3/8"UNC 2
17
15
1
40
39
26
24
4 22
23 19
14 8
6
25 21 3
20
11
2
12
16 9
10
27
13
7
18
504164-002 Page 6-3

30
33
32
33
34 31
35
37
29 28
Page 6-4 504164-002

Notes
504164-002 Page 6-5

Illustrated Parts Breakdown - Scissor Assembly X26
Scissor Assembly X26

500002-000
1 504101-000 SCISSOR WELDMENT - OUTER TOP & BOTTOM 2
2 504103-000 SCISSOR WELDMENT - OUTER STANDARD 1
3 504103-001 SCISSOR WELDMENT - OUTER STANDARD 3rd 2
4 504103-002 SCISSOR WELDMENT - OUTER STD(C/W BRACKET) 1
5 504104-001 SCISSOR WELDMENT - INNER STANDARD 1
6 504106-002 SCISSOR WELDMENT - INNER CYLINDER 1
7 504106-003 SCISSOR WELDMENT - INNER TOP 1
8 504106-004 SCISSOR WELDMENT - INNER BOTTOM 1
9 504186-000 PIVOT PIN - CHASSIS / PLATFORM 6
10 504122-004 PIVOT PIN - CYLINDER BODY & ROD 1
11 504122-003 PIVOT PIN - STANDARD (LONG) 2
12 504122-002 PIVOT PIN - SCISSOR STANDARD 11
13 504122-005 PIVOT PIN - SCISSOR STANDARD (TAPPED) 2
14 504186-001 PIVOT PIN - CHASSIS (FIXED) 2
15 504122-001 PIVOT PIN - STANDARD, MEDIUM 3
16 504123-000 PIVOT PIN - CYLINDER ROD 1
17 504038-000 PIVOT PIN - SCISSOR BRACE 3
18 504129-000 MAIN LIFT CYLINDER 1
19 504029-000 CABLE GUIDE CHANNEL 1
20 503790-001 SHORT CABLE GUIDE 1
21 504046-000 PIVOT BRACKET 2
22 504120-000 FLANGED BUSHING, 50mm 46
23 058819-000 GREASE NIPPLE, M6 14
24 504120-001 PLAIN BUSH, 50mm 2
25 504189-001 WASHER, M48 X 4mm THICK 2
26 056687-100 HEX HEAD BOLT, M16 X 100mm 1
27 056069-016 WASHER, M16 2
29 504177-000 ROLLER, TORSION ARM 1
30 056066-016 NYLOCK NUT, M16 1
31 504176-000 WELDMENT, TORSION ARM (LHS) 1
32 504176-001 WELDMENT, TORSION ARM (RHS) 1
10
28
29
28
30
10
Typical Pin Assembly
Page 6-6 504164-002

504164-002
Pivot Pins & Cylinder
Outside Scissor Members Inside Scissor Members & Trunking

9 9
12
13 20
12 12
13
1 16 7
15
17
12 18
12 15
3 6
17 19
12
3 11 12 21
2 5
10
17
12
4 9 14
1 8
# DENOTES PINS THAT ARE IN THE FOREGROUND

Page 6-7
Scissor Assembly X32

504202-000
1 504101-000 SCISSOR WELDMENT - OUTER TOP & BOTTOM 2
2 504103-000 SCISSOR WELDMENT - OUTER STANDARD 5
3 504103-002 SCISSOR WELDMENT - OUTER STD(C/W BRACKET) 1
4 504104-001 SCISSOR WELDMENT - INNER STANDARD 2
5 504106-000 SCISSOR WELDMENT - INNER TOP 1
6 504106-001 SCISSOR WELDMENT - INNER, CYLINER 1
7 504106-004 SCISSOR WELDMENT - INNER BOTTOM 1
8 504186-000 PIVOT PIN - CHASSIS / PLATFORM 6
9 504122-004 PIVOT PIN - CYLINDER BODY / ROD 2
10 504122-003 PIVOT PIN - STANDARD LONG 4
11 504122-002 PIVOT PIN - SCISSOR STANDARD 14
12 504122-000 PIVOT PIN - MID-CYLINDER MEMBER 2
13 504122-001 PIVOT PIN - STANDARD - MEDIUM 5
14 504186-001 PIVOT PIN - CHASSIS,FIXED 2
15 504038-000 PIVOT PIN - SCISSOR BRACE 2
16 504039-000 PIVOT PIN - SCISSOR BRACE (TOP) 1
17 504129-000 MAIN LIFT CYLINDER 1
18 504124-000 LIFT CYLINDER 1
19 504046-000 PIVOT BRACKET 4
20 504029-000 CABLE GUIDE CHANNEL 2
21 504043-000 WELDMENT, SCISSOR BRACE 1
22 009442-003 SPRING PLUNGER ASSEMBLY 1
23 504036-000 SCISSOR BRACE WELDMENT 1
24 504040-000 CLAMP WASHER 1
25 066189-004 SPACER PAD - 6mm 1
26 066189-001 SPACER PAD - 10mm 1
27 504189-000 M48 WASHER (8mm THICK) 2
29 056819-000 GREASE NIPPLE, M6 20
30 504187-000 PIN LOCK PLATE 30
10
28
29
28
30
10
Typical Pin Assembly
Page 6-8 504164-002

504164-002
Pivot Pins & Cylinders
8 8
Outside Scissor Members Inside Scissor Members & Trunking
11 10
11 18
1 5
13 11 20
11
19
2 4
12 12
11 13
16 17
2 13
2 6
10 11 20
15
2 11
19
2 4
9
8 14
15 FIXED
3 11 PIN
1 7
# DENOTES PINS THAT ARE IN THE FOREGROUND

Page 6-9
Illustrated Parts Breakdown - Scissor Assembly X26 (Lift Assist Assembly)
Scissor Assembly X26 (Lift Assist Assembly)
30
27
29
28
27
26
31
32
15
22
23
6 24
16
25
Lift Assist Assembly
Page 6-10 504164-002

Illustrated Parts Breakdown - Scissor Brace Assembly X26 & X32
Scissor Brace Assembly X26 & X32
Scissor Brace Assembly

27
15
26
25
24
23
21
22
504164-002 Page 6-11

Illustrated Parts Breakdown - Platform Assembly X32
Platform Assembly X32

504203-001
1 066262-001 WELDMENT, X32 PLATFORM 1

2 504138-000 LIFT STOP BRACKET 2
3 502148-001 WEAR PAD 2
4 504310-001 RAIL WELDMENT, PLATFORM RHS 1
5 504311-001 WELDMENT, DROP RAIL RHS 1
6 504311-000 WELDMENT, DROP RAIL LHS 1
7 504310-000 RAIL WELDMENT, PLATFORM LHS 1
8 504168-000 GUIDE WEAR PAD 2
9 502132-001 ROLLER, EXTENSION DECK 2
10 502129-000 ROLLER STOP 4
11 BELOW LOCK PIN ASSEMBLY 1
A 502322-000 LOCK PIN 1
B 502323-000 R-CLIP 1
C 058296-000 KEY RING 1
D 53192 CABLE 2
E 53195-02 CABLE CRIMP 4
12 504314-000 WELDMENT, SWING BAR 1
13 058557-000 PLASTIC CAP 3
14 057094-001 HARNESS HARDPOINT BRACKET 1
15 504026-000 BRACKET, GATE STOP 2
16 504315-000 WELDMENT, GATE 1
17 501352-001 LATCH 1
18 502204-001 GATE SPRING 1
19 502206-001 INSERT, GATE PIVOT 1
20 502231-000 PIPE CLAMP 1
Page 6-12 504164-002

Illustrated Parts Breakdown - Extension Deck Assembly X32
Extension Deck Assembly X32

504203-002
1 066294-002 WELDMENT, EXTENSION DECK 1

2 - GUIDE STRIP 2
3 502168-001 DECAL PANEL 1
4 504312-000 WELDMENT, EXTENSION DECK RAIL 1
5 504313-001 WELDMENT, SIDE DROP RAIL (RHS) 1
6 010076-000 MANUAL HOLDER 1
7 504314-000 WELDMENT, SWING BAR 1
8 058557-000 PLASTIC CAP 1
9 BELOW LOCK PIN ASSEMBLY 1
A 502322-000 LOCK PIN 1
B 502323-000 R-CLIP 1
C 058296-000 KEY RING 1
D 53192 CABLE 2
E 53195-02 CABLE CRIMP 4
10 504313-000 WELDMENT, SIDE DROP RAIL (LHS) 1
11 502141-000 LEVER BRACKET 1
12 009442-003 PLUNGER PIN ASSEMBLY 1
13 057094-001 HARNESS HARDPOINT BRACKET 1
14 502148-001 WEAR PAD 2
15 502145-000 WELDMENT, LEVER PIVOT BRACKET 1
16 504021-000 WELDMENT, ROLLER MOUNT 2
17 502097-000 ROLLER SHIM 2
18 502132-001 EXTENSION DECK ROLLER 2
504164-002 Page 6-13

Illustrated Parts Breakdown - Power Module Assembly
Power Module Assembly

X26 & X32
1 501074-000 BATTERY 4
2 066309-011 WELDMENT, DOOR MODULE 1
3 062791-002 LATCH 1
4 066735-001 WELDMENT, POTHOLE 1
5 504133-000 BRACKET, GUIDE PAD ANGLE 1
6 066713-002 HINGE 1
7 - - -
8 504132-000 HYDRAULIC CYLINDER, POTHOLE 1
9 504153-001 PIVOT PIN, POTHOLE 2
10 504135-000 BUSHING, POTHOLE PIVOT 2
11 504126-000 BUSHING, MODULE PIVOT 2
12 500858-001 SPLIT PIN 1
13 - - -
14 504134-000 GUIDE PAD 2
15 - - -
5 12
2 1
14
11
6
10
Page 6-14 504164-002

Illustrated Parts Breakdown - Control Module Assembly
Control Module Assembly

X26 & X32
1 504128-001 HYDRAULIC TANK 1

2 062791-002 LATCH 1
3 502588-000 ALARM 1
4 502489-000 LINE CONTACTOR 1
5 502494-000 MAIN FUSE 1
6 503758-000 MOUNTING PLATE, FUSE 1
7 066310-010 WELDMENT, CONTROL MODULE 1
8 504126-000 BUSHING, MODULE HINGE 2
9 504135-000 BUSHING, POTHOLE PIVOT 2
10 504153-001 PIVOT PIN, POTHOLE WELDMENT 2
11 066735-001 WELDMENT, POTHOLE 1
12 503800-001 MAIN MANIFOLD BLOCK 1
13 504536-000 PUMP ASSEMBLY 1
14 504133-000 BRACKET, GUIDE PAD ANGLE 1
15 504134-000 GUIDE PAD 1
16 500858-001 SPLIT PIN 1
17 504132-000 HYDRAULIC CYLINDER, POTHOLE 1
18 504023-000 MOUNTING PLATE, HYDRAULIC BLOCK 1 1
17
2 3
4
5
6
16 7
15
8
14
12 18
13 11
10
504164-002 Page 6-15

Illustrated Parts Breakdown - Control Valve Assembly
Control Valve Assembly

503800-000
1 TEST PORT 1
2 058358-000 FITTING, 1/4” - 1/4” MALE/MALE 1
7 058590-000 FITTING, 1/4 M/M ADAPTOR WITH 1mm OROFICE 1
10 - - -
11 057377-000 FITTING, 1/2” - 1/2” (MALE/MALE) 1
12 503802-000 CHECK VALVE, POTHOLE 1
13 503803-000 CROSS LINE RELIEF VALVE (DRIVE) 1
14 503804-000 VALVE, SOLENOID (DRIVE) 1
15 503805-000 VALVE, SOLENOID (DRIVE/LIFT) 1
16 503803-000 CROSS LINE RELIEF VALVE (DRIVE) 1
17 503807-000 PRESSURE RELIEF (MAIN LIFT) 1
18 503808-000 VALVE, SOLENOID (STEERING) 1
19 503809-000 FLOW RESTRICTOR (STEERING) 1
20 503810-000 RELIEF VALVE (STEERING) 1
22 503810-000 RELIEF VALVE (MAIN RELIEF) 1
23 500303-000 COIL 18V 6
8
5
9 7 6 3 2
4 1
22
21
12 20
13
18 19
17
14 15
16
Page 6-18 504164-002

Illustrated Parts Breakdown - Lower Controls Assembly
Lower Controls Assembly

504348-000
1 504141-000 COVER, LOWER CONTROL BOX 1

2 504142-000 BOX, LOWER CONTROL BOX 1
3 501867-000 EMERGENCY STOP BUTTON 1
4 502251-000 TOGGLE SWITCH 1
5 502250-000 ENABLE BUTTON 1
6 502544-000 KEY 1
7 502589-000 KEY SWITCH 1
7
6
5
4
3 2
504164-002 Page 6-17

Illustrated Parts Breakdown - Hydraulic Tank Assembly
Hydraulic Tank Assembly

504128-001
1 - TANK WELDMENT 1
2 057534-000 FILLER, BREATHER & DIPSTICK (CAP) 1
3 - INSPECTION COVER & GASKET 1
4 057377-000 HYDRAULIC FITTING (1/2” M/M BSP) 1
5 057358-000 HYDRAULIC FITTING (1/4” M/M BSP) 1
6 058350-000 HYDRAULIC FITTING (3/4” BSP) 1
7 058359-000 SUCTION FILTER 1
8 057108-000 3/8 DRAIN PLUG 1
1
2
3
6
7
8
Page 6-18 504164-002

Illustrated Parts Breakdown - Upper Controls Assembly
Upper Controls Assembly

504349-000
1 501867-000 EMERGENCY STOP BUTTON 1

2 501882-002 RUBBER BOOT, STEERING 1
3 501882-000 JOYSTICK 1
4 501882-001 RUBBER BOOT, JOYSTICK 1
5 502486-000 DECAL 1
6 501592-000 MOUNTING PLATE 1
7 502591-000 SEAL 1
8 502453-000 CIRCUIT BOARD 1
9 502587-001 SOCKET, MAIN HARNESS 1
10 502605-000 SOCKET, OVERLOAD 1
11 502496-000 UCB, BOX ONLY 1
1 3
11 9
10
504164-002 Page 6-19

Illustrated Parts Breakdown - Hydraulic Block (Series / Parallel)
Hydraulic Block (Series / Parallel)

504151-000
1 500303-000 SOLENOID COIL 18V 2

2 057122-000 HYDRAULIC FITTING, 3/8 X 3/8 MALE MALE 4
Page 6-20 504164-002

Illustrated Parts Breakdown - Hydraulic Assembly
Hydraulic Assembly
504007-000 (X26)
1 504250-000 HYDRAULIC HOSE, BLOCK - SERIES/PARA BLOCK 1

2 504251-000 HYDRAULIC HOSE, BLOCK D2 - SERIES/PARA D2 1
3 504252-000 HYDRAULIC HOSE,SERIES/PARA BLOCK - MOTORS 4
4 504253-000 HYDRAULIC HOSE, BLOCK - BRAKE TEE 1
5 504254-000 HYDRAULIC HOSE, BRAKE TEE - MOTORS 2
6 504255-000 HYDRAULIC HOSE, BLOCK - STEERING CYLINDER 2
7 504256-000 HYDRAULIC HOSE, BLOCK - POTHOLE TEE 1
9 504260-000 HYDRAULIC HOSE, TEE (RHS) - POTHOLE CYL 1
11 504258-000 HYDRAULIC HOSE, TEE (LHS) - POTHOLE CYL 1
13 - - -
14 - - -
15 - - -
16 - - -
17 - - -
18 - - -
19 - - -
20 504269-000 HYDRAULIC HOSE, TANK - PUMP (SUCTION) 1
21 504270-000 HYDRAULIC HOSE, PUMP - BLOCK (PRESSURE) 1
22 504271-000 HYDRAULIC HOSE,BLOCK - FILTER (RETURN) 1
23 504272-000 HYDRAULIC HOSE, BLOCK - LIFT CYL 1
24 504273-000 HYDRAULIC HOSE, LIFT CYLINDER - TANK DRAIN 1
26 504132-000 HYDRAULIC CYLINDER (POTHOLE) 2
28 503800-001 BLOCK, MAIN MANIFOLD 1
29 - - -
30 - - -
31 504129-000 HYDRAULIC CYLINDER, LIFT (LOWER) 1
32 504148-000 HYDRAULIC CYLINDER, STEER 1
33 504151-000 HYDRAULIC BLOCK, SERIES / PARALLEL 1
34 114055-000 MOTOR, HYDRAULIC 2
35 - - -
504164-002 Page 6-21

Page 6-22 504164-002

Hydraulic Assembly
504207-000 (X32)

6 504255-000 HYDRAULIC HOSE, BLOCK - STEERING CYLINDER 2
13 - - -
14 504263-000 HYDRAULIC HOSE, PRESSURE SWITCH - LWR LIFT TEE 1
15 504264-000 HYDRAULIC HOSE, TEE - LIFT CYL LOWER 1
16 504265-000 HYDRAULIC HOSE, TEE - LIFT CYL UPPER 1
17 504266-000 HYDRAULIC HOSE, LIFT CYL UPPER - DRAIN TEE 1
18 504267-000 HYDRAULIC HOSE, LIFT CYL LOWER - DRAIN TEE 1
19 504268-000 HYDRAULIC HOSE, DRAIN TEE - TANK 1
20 504269-000 HYDRAULIC HOSE, TANK - PUMP (SUCTION) 1
21 504270-000 HYDRAULIC HOSE, PUMP - BLOCK (PRESSURE) 1
22 504271-000 HYDRAULIC HOSE,BLOCK - FILTER (RETURN) 1
23 - - -
24 - - -
26 504132-000 HYDRAULIC CYLINDER (POTHOLE) 2
28 503800-001 BLOCK, MAIN MANIFOLD 1
29 - - -
30 504124-000 HYDRAULIC CYLINDER, LIFT (UPPER) 1
31 504129-000 HYDRAULIC CYLINDER, LIFT (LOWER) 1
32 504148-000 HYDRAULIC CYLINDER, STEER 1
33 504151-000 HYDRAULIC BLOCK, SERIES / PARALLEL 1
34 114055-000 MOTOR, HYDRAULIC 2
35 - - -
504164-002 Page 6-23

Page 6-24 504164-002

Illustrated Parts Breakdown - Hydraulic Cylinder Assembly (Lift, Lower)
Hydraulic Cylinder Assembly (Lift, Lower)

X26 & X32
504129-001 (ANSI 504129-002)
1 - CYLINDER BODY 1
2 SOLENOID VALVE (EMERGENCY DOWN) 1
3 - LOCK NUT 1
4 - PISTON HEAD 1
5 504129-010 SEAL KIT 1
6 - SPACING SLEEVE 1
7 - CAP, BODY END 1
8 - CYLINDER ROD 1
9 504120-000 FLANGED BUSHING 4
10 058819-000 M6 GREASE NIPPLE 2
10
9
3
4 5
6
7
504164-002 Page 6-25

Illustrated Parts Breakdown - Hydraulic Cylinder Assembly (Lift, Upper)
Hydraulic Cylinder Assembly (Lift, Upper)

X32 ONLY
504124-000
1 - CYLINDER BODY 1
2 SOLENOID VALVE (EMERGENCY DOWN) 1
3 - LOCK NUT 1
4 - PISTON HEAD 1
5 504124-010 SEAL KIT 1
6 - SPACING SLEEVE 1
7 - CAP, BODY END 1
8 - CYLINDER ROD 1
9 504120-000 FLANGED BUSHING 4
10 058819-000 M6 GREASE NIPPLE 2
10
9
3
4 5
6
7
Page 6-26 504164-002

Illustrated Parts Breakdown - Hydraulic Cylinder Assembly (Steer)
Hydraulic Cylinder Assembly (Steer)

504148-000
1 - CYLINDER BODY
2 - LOCK NUT
3 - PISTON HEAD
4 504148-010 SEAL KIT
5 - CAP, BODY END
6 - CYLINDER ROD
5
4
3
504164-002 Page 6-27

Illustrated Parts Breakdown - Hydraulic Cylinder Assembly (Pothole)
Hydraulic Cylinder Assembly (Pothole)

504132-000
1 - CYLINDER BODY 1
2 SOLENOID VALVE 1
3 - LOCK NUT 1
4 - PISTON HEAD 1
5 504132-010 SEAL KIT 1
6 - CAP, BODY END 1
7 - CYLINDER ROD 1
7
6
5
4
3
Page 6-28 504164-002

Illustrated Parts Breakdown - Electrical Assembly X26
Electrical Assembly X26

504008-000
Item Part Description QTY. Item Part Description QTY.
1 502483-000 ECU 1 15 502596-000 HARNESS, BATTERY INTERCONNECT 3

2 502593-000 J1 HARNESS 1 16 503097-000 CHARGER 1
3 503800-001 MAIN MANIFOLD BLOCK 1 17 058783-000 CHARGER DISCONNECT PLUG 1
4 505005-000 UPPER CONTROLS 1 18 502597-000 HARNESS, CHARGER DISCONNECT (+) - LINE CON4 1
5 505006-000 LOWER CONTROLS 1 19 502598-000 HARNESS, CHARGER DISCONNECT (-) - BATT (-) 1
6 058912-000 TILT SENSOR 1 20 502599-000 HARNESS, CHARGER DISCONNECT (-) - LINE CON2 1
7 501868-000 HORN 1 21 502600-000 LINE CONTACTOR 3 - FUSE 1
8 502588-000 ALARM 1 22 502601-000 LINE CONTACTOR 5 - LINE CONTACTOR 3 1
9 505072-000 PROXIMITY SENSOR 1 23 502489-000 LINE CONTACTOR 1
10 502494-000 FUSE 1 24 502602-000 LINE CONTACTOR 2 - MOTOR CONT B- 1
11 058937-000 BATTERY DISCONNECT PLUG 1 25 502603-000 LINE CONTACTOR 1 - MOTOR CONT ENABLE 1
12 502594-000 HARNESS, BATTERY DISCONNECT - BATT (-) 1 26 502604-000 LINE CONTACTOR 6 - PUMP MOTOR 1
13 502595-000 HARNESS, BATTERY DISCONNECT - BATT (+) 1 27 502492-000 MOTOR CONTROLLER 1
14 501074-000 BATTERY 4 28 114071-000 PUMP MOTOR 1
504164-002 Page 6-29

Illustrated Parts Breakdown - Electrical Assembly X32
Electrical Assembly X32

504208-000
1 502483-000 ECU 1 17 058783-000 CHARGER DISCONNECT PLUG 1

2 502593-000 J1 HARNESS 1 18 502597-000 HARNESS, CHARGER DISCONNECT (+) - LINE CON4 1
3 503800-001 MAIN MANIFOLD BLOCK 1 19 502598-000 HARNESS, CHARGER DISCONNECT (-) - BATT (-) 1
4 505005-000 UPPER CONTROLS 1 20 502599-000 HARNESS, CHARGER DISCONNECT (-) - LINE CON2 1
5 505006-000 LOWER CONTROLS 1 21 502600-000 LINE CONTACTOR 3 - FUSE 1
6 058912-000 TILT SENSOR 1 22 502601-000 LINE CONTACTOR 5 - LINE CONTACTOR 3 1
7 501868-000 HORN 1 23 502489-000 LINE CONTACTOR 1
8 502588-000 ALARM 1 24 502602-000 LINE CONTACTOR 2 - MOTOR CONT B- 1
9 505072-000 PROXIMITY SENSOR 1 25 502603-000 LINE CONTACTOR 1 - MOTOR CONT ENABLE 1
10 502494-000 FUSE 1 26 502604-000 LINE CONTACTOR 6 - PUMP MOTOR 1
11 058937-000 BATTERY DISCONNECT PLUG 1 27 502492-000 MOTOR CONTROLLER 1
12 502594-000 HARNESS, BATTERY DISCONNECT - BATT (-) 1 28 114071-000 PUMP MOTOR 1
13 502595-000 HARNESS, BATTERY DISCONNECT - BATT (+) 1 29 504151-000 HYDRAULIC BLOCK, SERIES / PARALLEL 1
14 501074-000 BATTERY 4 30 504374-000 EMERGENCY DOWN ASSEMBLY 1
15 502596-000 HARNESS, BATTERY INTERCONNECT 3 31 504169-000 BATTERY, EMERGENCY DOWN 2
16 503097-000 CHARGER 1
Page 6-30 504164-002

Illustrated Parts Breakdown - Overload Assembly
Overload Assembly
504557-000
1 503950-000 MOUNTING PLATE, ELECTRICAL BOX 1

2 504566-000 MOUNTING PLATE, CIRCUIT BOARD 1
3 504558-000 CIRCUIT BOARD 1
4 504559-000 ANGLE TRANSDUCER 1
5 504560-000 PRESSURE TRANSDUCER 1
504164-002 Page 6-31

Illustrated Parts Breakdown - Overload Assembly
Notes :
Page 6-32 504164-002

Illustrated Parts Breakdown - Decal Assembly X26
Decal Assembly X26

504009-000
1 101210-000 DECAL, HYDROGEN GAS 1 13 062562-951 DECAL, BATTERIES ARE BALLAST 2

2 066551-950 DECAL, SAFE WORKING LOAD (EXT DECK) 1 14 502486-000 DECAL, UPPER CONTROL BOX 1
3 066557-957 DECAL, SAFE WORKING LOAD (MAIN DECK) 1 15 066522-900 DECAL, BATTERY SYMBOL 1
4 014222-903 DECAL, FORKLIFT POINT 1 16 501453-000 DECAL, WARNING CRUSHING (FOOT) 4
5 503724-000 DECAL, WARNING CRUSHING (HAND) 2 17 503723-000 DECAL, BATTERY DISCONNECT 1
6 060197-000 DECAL, HYDRAULIC FLUID 1 18 068635-001 DECAL, HARNESS HARDPOINT 2
7 100102-900 DECAL, NOT INSULATED 1 19 067195-001 DECAL, THREE HAZARDS (ENGLISH) 1
8 066561-902 DECAL, SCISSOR BRACE 1 19 067195-201 DECAL, THREE HAZARDS (GERMAN) 1
9 005223-906 DECAL, EMERGENCY DOWN 1 19 067195-301 DECAL, THREE HAZARDS (FRENCH) 1
10 010076-901 DECAL, DOCUMENTS ENCLOSED 1 20 107053-000 DECAL, HORN 1
11 066556-900 DECAL, DANGER ABOVE 2 21 504193-000 DECAL, LIVERY (X26) 2
12 503721-000 DECAL, LOWER CONTROL BOX 1 22 504196-000 DECAL, “UpRight” (LARGE) 2
504164-002 Page 6-33

Illustrated Parts Breakdown - Decal Assembly X32
Decal Assembly X32

504209-000
1 101210-000 DECAL, HYDROGEN GAS 1 13 062562-951 DECAL, BATTERIES ARE BALLAST 2

2 066551-950 DECAL, SAFE WORKING LOAD (EXT DECK) 1 14 502486-000 DECAL, UPPER CONTROL BOX 1
3 066557-950 DECAL, SAFE WORKING LOAD (MAIN DECK) 1 15 066522-900 DECAL, BATTERY SYMBOL 1
4 014222-903 DECAL, FORKLIFT POINT 1 16 501453-000 DECAL, WARNING CRUSHING (FOOT) 4
5 503724-000 DECAL, WARNING CRUSHING (HAND) 2 17 503723-000 DECAL, BATTERY DISCONNECT 1
6 060197-000 DECAL, HYDRAULIC FLUID 1 18 068635-001 DECAL, HARNESS HARDPOINT 2
7 100102-900 DECAL, NOT INSULATED 1 19 067195-001 DECAL, THREE HAZARDS (ENGLISH) 1
8 066561-902 DECAL, SCISSOR BRACE 1 19 067195-201 DECAL, THREE HAZARDS (GERMAN) 1
9 005223-908 DECAL, EMERGENCY DOWN 1 19 067195-301 DECAL, THREE HAZARDS (FRENCH) 1
10 010076-901 DECAL, DOCUMENTS ENCLOSED 1 20 107053-000 DECAL, HORN 1
11 066556-900 DECAL, DANGER ABOVE 2 21 504194-000 DECAL, LIVERY (X26) 2
12 503721-000 DECAL, LOWER CONTROL BOX 1 22 504196-000 DECAL, “UpRight” (LARGE) 2
Page 6-34 504164-002

Local Distributor:
Lokaler Vertiebshändler:
Distributeur local:
El Distribuidor local:
Il Distributore locale:
USA Europe
TEL: +1 (559) 443 6600 TEL: +44 (0) 845 1550 058
FAX: +1 (559) 268 2433 FAX: +44 (0) 195 2299 948
www.upright.com PN - 504164-003

504164-003 X-32 sn53095-53100 C.PS

Uploaded by

Copyright:

Available Formats

504164-003 X-32 sn53095-53100 C.PS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

504164-003 X-32 sn53095-53100 C.PS

Uploaded by

Copyright:

Available Formats

ERVICE & PARTS MANUAL

The Machine rating has been changed from:

Windspeed rating of 12.5 m/s (Beaufort 6)

Windspeed rating of 7 m/s (Beaufort 4)

Please attach to the front cover of

Stamped Serial Number

HOW TO USE THIS MANUAL

NOTE: Gives helpful information.

1.2 GENERAL DESCRIPTION

Figure 1-1: X26-32

Electrocution Hazard Tip Over Hazard Collision Hazard Fall Hazard

Page 2 Operation Manual

Operation Manual Page 3

LIFT OVERLOAD ALARM

Page 4 Operation Manual

C ONTROLS AND I NDICATORS

Operation Manual Page 5

P RE -O PERATION S AFETY I NSPECTION

Page 6 Operation Manual

S YSTEM F UNCTION I NSPECTION

Operation Manual Page 7

1. Mount the platform and properly close the entrance.

ELEVATING THE PLATFORM

Page 8 Operation Manual

TR A V E L W I T H THE PLATFORM ELEVATED

LOWERING THE PLATFORM

Operation Manual Page 9

LOWER THE G U A R D R A I L S , X26

FOLD DOWN GUARDRAILS, X32

FOLD DOWN PROCEDURE

Page 10 Operation Manual

AFTER USE EACH DAY

TRANSPORTING THE WORK P LATFORM

Operation Manual Page 11

Rear Tie Down/Lift Lugs

1. Move the machine onto the truck or trailer;

Front Tie Down Lugs FRONT

Page 12 Operation Manual

Figure 8: Scissor Brace

BLOCKING THE ELEVATING

3. Pull Platform EMERGENCY STOP Switch to the ON posi-

SCISSOR BRACE STOWAGE

Operation Manual Page 13

Charge the batteries at the end of each work

Page 14 Operation Manual

I NSPECTION AND M AINTENANCE S CHEDULE

D AILY P REVENTATIVE M AINTENANCE C HECKLIST

N = No/Not Acceptable Owner: _____________________________________

R = Repaired/Acceptable Model No: ___________________________________

Serial No: ___________________________________

Serviced By: _________________________________

Check electrolyte level. Hydraulic Fluid Check fluid level.

Operation Manual Page 15

Page 16 Operation Manual

Operation Manual Page 17

Page 18 Operation Manual

ITEM X26 X32

Operation Manual Page 19

Page 20 Operation Manual