Bluetooth Module Datasheet

Model: TS64215

Tinyos Electronics @ 2016

Version 1.2

1
List of Contents

1 Introduction...................................................................................................................................................3

2 Key Features.................................................................................................................................................3

3 Applications...................................................................................................................................................4

4 Block Diagram..............................................................................................................................................4

5 General specifications.............................................................................................................................4

6 Module Package Information................................................................................................................5

6.1 Pinout Diagram and package dimensions.........................................................................5

6.2 Module Pin descriptions..............................................................................................................6

7 Electrical Characteristics.......................................................................................................................8

7.1 Absolute Maximum Ratings.......................................................................................................8

7.2 Recommended Operating Conditions...................................................................................8

8 Recommended reflow temperature profile....................................................................................9

2
1 Introduction
Tinysine Electronics introduces the pioneer of the Bluetooth 4.2 modules TS-64215
which is a high performance, cost effective, low power and compact solution. The
Bluetooth module provides a complete 2.4GHz Bluetooth system based on the
BlueCore CSRA64215 chipset which is a single chip radio and baseband IC for
Bluetooth 2.4GHz systems. This module is fully compliant to Bluetooth v4.2 for audio
communications.

2 Key Features
Bluetooth Profiles
 Bluetooth v4.2 specification support
 A2DP v1.3
 AVRCP v1.6
 HFP v1.6
 HSP v1.2
 DI v1.3

Music Enhancements
 aptX, aptX Low Latency, SBC and AAC
 TrueWireless Stereo (TWS)
 Configurable Signal Detection to trigger events
 Up to 10 stages of Speaker Parametric EQ
 Up to 6 banks of 5 stages of User Parametric EQ for music playback (user,
rock, pop, classical, jazz, etc)
 MeloD Expansion 3D stereo widening and phase shifting effect
 Volume Control
 Compander to compress or expand the dynamic range of the audio
 Post Mastering to improve DAC fidelity
 Volume Boost

Additional Functionality
 Support for multi-language programmable audio prompts
 CSR's proximity pairing and CSR's proximity connection
 Multipoint support for A2DP connection to 2 A2DP sources for music playback
 Talk-time extension
 Slim module with 28.5mm x 13mm x 2.0mm
3
3 Applications
 Stereo Headsets
 Wired Stereo headsets and headphones
 Portable Bluetooth Stereo speakers

4 Block Diagram

5 General specifications

Model Name TS-64215

Product Description Bluetooth 4.2 Class2 Module
Bluetooth Standard Bluetooth 4.2
Chipset CSRA64215
Dimension 28.5mm x 13mm x 2.0mm
Operating Conditions
Voltage 2.8~4.2V
Temperature -10～+70℃
Storage Temperature -40～+85℃
Electrical Specifications
Frequency Range 2402～2480MHz
Maximum RF Transmit Power 4dBm
π/4 DQPSK Receive Sensitivity -92dBm
8DPSK Receive Sensitivity -82dBm

4
6 Module Package Information

6.1 Pinout Diagram and package dimensions

Unit：MM

Recommended PCB layout footprint

5
6.2 Module Pin descriptions

Pin
Pin Name Pin Type Description
No.
1 PIO6 Bidirectional with strong pull-down Programmable input/output line 6
2 PIO8 Bidirectional with strong pull-up Programmable input/output line 8
3 PIO1 Bidirectional with strong pull-up Programmable input/output line 1
4 PIO0 Bidirectional with strong pull-up Programmable input/output line 0
5 LED1 Bidirectional LED driver
6 AIO0 Bidirectional Analogue programmable input/output line
7 PIO17 Bidirectional with strong pull-down Programmable input/output line 17
8 PIO9 Bidirectional with strong pull-down Programmable input/output line 9

6
9 PIO7 Bidirectional with strong pull-down Programmable input/output line 7
10 1V8 1.8V output 1.8V output for keys

11 PIO16 Bidirectional with strong pull-up Programmable input/output line 16

12 NC NC NC
13 NC NC NC
14 PIO21 Bidirectional with weak pull-down Programmable input/output line 21
15 PIO18 Bidirectional with weak pull-down Programmable input/output line 18
SPI/PCM select input:
16 SPI_PCM# Input with weak pull-down 0 = PCM/PIO interface
1 = SPI
17 GND VSS Ground
18 USB_P Bidirectional USB data plus
19 USB_N Bidirectional USB data minus
Reset if low. Pull low for minimum
20 RSTn Input with strong pull-up
5ms to cause a reset.
Programmable input / output line 2
Alternative function:
SPI_MOSI: Debug SPI data input
PCM1_IN: PCM1 synchronous data
21 SPI_MOSI Bidirectional with weak pull-down input
I2S1_SD_IN: I²S1 synchronous data
input
SPDIF_IN: SPDIF input
Programmable input / output line 5
Alternative function:
SPI_CLK: Debug SPI clock
22 SPI_CLK Bidirectional with weak pull-down PCM1_CLK: PCM1 synchronous
data clock
I2S1_SCK: I²S1 synchronous data
clock
Programmable input / output line 4
Alternative function:
SPI_CS#: chip select for Debug
23 SPI_CSB Bidirectional with weak pull-down SPI, active low
PCM1_SYNC: PCM1 synchronous
data sync
I2S1_WS: I²S1 word select
Programmable input / output line 3
Alternative function:
SPI_MISO: Debug SPI data output
24 SPI_MISO Bidirectional with weak pull-down PCM1_OUT: PCM1 synchronous
data output
I2S1_SD_OUT: I²S1 synchronous
data output
25 VCHG Charger voltage input Internal charger input for charging
26 GND VSS Ground
27 VBAT Battery positive terminal Power supply input for 2.7~4.2V
28 LED0 Bidirectional LED driver
29 LED2 Bidirectional LED driver
30 VREG_EN Power on/off key input Power on/off input key indication

7
31 MIC BIAS Analog Microphone bias output
32 LINE_BP Analog input Line input positive, channel B
33 LINE_BN Analog input Line input negative, channel B
34 LINE/MIC_AP Analog input Line or microphone input positive, channel
35 LINE/MIC_AN Analog input Line or microphone input negative, channe
36 SPK_BN Analog output Speaker output negative right
37 SPK_BP Analog output Speaker output positive right
38 SPK_AN Analog output Speaker output negative left
39 SPK_AP Analog output Speaker output positive left
40 GND VSS Ground

7 Electrical Characteristics
7.1 Absolute Maximum Ratings

Rating Minimum Maximum

Storage temperature -40℃ +85℃

7.2 Recommended Operating Conditions

Operating Condition Minimum Maximum

Operating temperature range -10℃ +70℃
Supply voltage: VBAT +2.8V +4.2V

8
8 Recommended reflow temperature profile

The module Must go through 125℃ baking for at least 9 hours before SMT
AND IR reflow process!

若拆封后未立即上线，建议让模块下次上线前务必以 125℃烘烤 9 小时以上！

9
Record of Changes
Data Revision Description
2015-11-26 V1.0 Original publication of this document.
2016-01-29 V1.2

IMPORTANT NOTICE
Tinysine Technologies Co.,Ltd reserve the right to make changes to their
products or to discontinue any product or service without notice, and advise
customers to obtain the latest version of relevant information to verify,
before placing orders, that information being relied on is current. All
products are sold subject to the Tinysine terms and conditions of sale
supplied at the time of order acknowledgement, including those pertaining to
warranty, patent infringement, and limitation of liability.
Tinysine warrants performance of its products to specifications applicable at
the time of sale in accordance with Tinysine’s standard warranty. Testing and
other quality control techniques are utilized to the extent Tinysine deems
necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government
requirements.
In order to minimize risks associated with customer applications, adequate
design and operating safeguards must be used by the customer to minimize
inherent or procedural hazards. Tinysine products are not authorized for use
as critical components in life support devices or systems without the express
written approval of an officer of the company. Life support devices or systems
are devices or systems that are intended for surgical implant into the body, or
support or sustain life, and whose failure to perform when properly used in
accordance with instructions for use provided, can be reasonably expected to
result in a significant injury to the user. A critical component is any
component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system,
or to affect its safety or effectiveness.
Tinysine assumes no liability for applications assistance or customer product design.
Tinysine does not warrant or represent that any license, either express or
implied, is granted under any patent right, mask work right, or other
intellectual property right of Tinysine covering or relating or any combination,
machine, or process in which such products or services might be or are used.

10