Datasheet

SPB2301010xx_RevE.docx

SPB2301010xD – SFP+ Single Fibre

Tx 1270nm Rx 1330nm / 10km / 10x Gigabit Ethernet

For your product safety, please read the following information carefully before any manipulation of the transceiver:

ESD
This transceiver is specified as ESD threshold 1kV for SFI pins and 2kV for all others electrical input pins, tested per MIL-STD-883G, Method 3015.4 /JESD22-
A114-A (HBM). However, normal ESD precautions are still required during the handling of this module.

LASER SAFETY
This is a Class1 Laser Product according to IEC 60825-1:2007. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated (June 24, 2007).

The optical ports of the module need to be terminated with an optical connector or with a dust plug in order to avoid contamination.

1. Overview
SPB2301010xx is a high-performance transceiver module for up to 10´ Gigabit Ethernet data links over a single mode fibre. The
maximum reach1 is 10km, with 9dB end of life (EOL) power budget. The transmitter is a 1270nm DFB laser, the receiver a
1330nm PIN photodiode. Consequently, a module with a 1330nm transmitter and a 1270nm receiver is required at the opposite
side of the link. The recommended counterpart is SPB3201010xx.
This transceiver module is compliant with the Small Form-factor Pluggable (SFP+) Multisource Agreement (MSA) and hot
pluggable. Always contact Skylane Optics® commercial agents for compatibility with different equipment platforms.

2. Features
• SFP+ Multi-Source Agreement compliant (SFF-8431)
• Hot pluggable SFP+ footprint
• Serial ID functionality supported according to (SFF-8472)
• Class 1 laser safety standard IEC 60825 compliant
• Single LC connector
• 1270nm DFB transmitter, 1330nm PIN receiver
• 10km point-to-point transmission on single mode fibre
• Operating temperature range 0°C to 70°C or -40°C to 85°C
• Low power dissipation (<1.5W) Figure 1. SFP+ Single Fiber
(non-binding illustration)
• Digital diagnostics monitoring (DDM)

3. Applications
• 10´ Gigabit Ethernet
• 9.83 Gbps CPRI
• 8´ Fiber Channel
• 4´ Fiber Channel
• 2´ Fiber Channel

4. Optical Interface

Wavelength Optical Output Receiver Dispersion Receiver Overload4 Power Budget2

P/N
[nm] Power2 [dBm] Sensitivity3 [dBm] Penalty [dB] [dBm] [dB]
SPB2301010xx Tx 1270 -5 to 0 ≤ -14 N/A 0 ≥9
Rx 1330
1. Distance is estimated assuming typical optical losses after decent quality fibre deployment; Only optical budget value is guaranteed.
2. EOL, over operating temperature range, together with SPB3201010xx
3. Measured with 10.3125Gbps PRBS 231-1, BER≤10-12
4. The optical input to the receiver should not exceed this value. Transmitters must never be directly connected to receivers (optical loop back) before ensuring that proper optical
attenuation is used

5. Technical Parameters
5.1. Recommended Operating Conditions

Specification subject to change without notice 1

Datasheet
SPB2301010xx_RevE.docx

Parameter Min Typ Max Unit Notes

Storage temperature -40 85 °C
SPB23010100D, SPB23010100B,
0 70
Operating Case Temperature °C SPB2301010GD, SPB2301010AD
-40 85 SPB23010102D, SPB23010102B
Relative Humidity 5 95 %
Power Supply Voltage 3.15 3.3 3.45 V

5.2. Transmitter Optical Specifications

Parameter Min Typ Max Unit Notes

Average Output Power -5 0 dBm 5
Centre Wavelength 1260 1270 1280 nm
Spectral Width (-20dB) 1 nm
Extinction Ratio 3.5 dB
Dispersion Penalty N/A dB
5. Output power coupled into a 9/125 µm single-mode fibre

5.3. Receiver Optical Specifications

Parameter Min Typ Max Unit Notes

Receiver Sensitivity -14 dBm 6
Receiver Overload 0 dBm 6
Receiver Operating Range 1320 1340 nm
6. Measured with 10.3125Gbps PRBS 231-1, BER≤10-12

6. Transceiver Electrical Pad Layout

VeeT 20
1 VeeT TD- 19
2 Tx_Fault TD+ 18
3 Tx_Disable VeeT 17
4 SDA VccT 16
Towards BEZEL ← 5 SCL VccR 15 → Towards ASIC
6 MOD_ABS VeeR 14
7 RS0 RD+ 13
8 Rx_LOS RD- 12
9 RS1 VeeR 11
10 VeeR

Figure 2. Transceiver Electrical Pad Layout

7. Module Electrical Pin Definition

SFP+ MSA (SFF-8431)

Pin Number Name Function

Specification subject to change without notice 2

Datasheet
SPB2301010xx_RevE.docx

1 VeeT Module Transmitter Ground

2 Tx_Fault Module Transmitter Fault
3 Tx_ Disable Transmitter Disable
4 SDA 2-Wire Serial Interface Data
5 SCL 2-Wire Serial Interface Clock
6 Mod_ABS Module Absent
7 RS0 Not Used
8 Rx_LOS Receiver Loss of Signal
9 RS1 Not Used
10 VeeR Module Receiver Ground
11 VeeR Module Receiver Ground
12 RD- Receiver Inverted Data Output
13 RD+ Receiver Non-Inverted Data Output
14 VeeR Module Receiver Ground
15 VccR Module Receiver 3.3V Supply
16 VccT Module Transmitter 3.3V Supply
17 VeeT Module Transmitter Ground
18 TD+ Transmitter Non-Inverted Data Input
19 TD- Transmitter Inverted Data Input
20 VeeT Module Transmitter Ground

8. EEPROM

SFP+ MSA (SFF-8472)

2 wire address 1010000x 2 wire address 1010001x

0 0
Alarm and Warning
Thresholds (56 bytes)
Serial ID Defined by
55
SFP MSA (96 bytes) Cal Constants
(40 bytes)
95 95
Real Time Diagnostic
Vendor Specifics Interface (24 bytes)
(32 bytes) 119
Vendor Specifics (8 bytes)
127 127
User writable EEPROM
Reserved (120 bytes)
(128 bytes) 247
Vendor Specifics (8 bytes)
255 255

A0h A2h

Figure 3. EEPROM of a SFP+

Specification subject to change without notice 3

Datasheet
SPB2301010xx_RevE.docx

9. Ordering Information

Part Number Description

SPB23010100D SFP+ Single Fibre, Tx 1270nm (DFB) , Rx 1330nm (PIN), maximum distance 10km,
power budget 9dB, 10x Gigabit Ethernet, LC connector, 0°C to 70°C, DDM
SPB23010100B SFP+ Single Fibre, Tx 1270nm (DFB) , Rx 1330nm (PIN), maximum distance 10km,
power budget 9dB, 10x Gigabit Ethernet, LC connector, Gen B, 0°C to 70°C, DDM
SPB23010102D SFP+ Single Fibre, Tx 1270nm (DFB) , Rx 1330nm (PIN), maximum distance 10km,
power budget 9dB, 10x Gigabit Ethernet, LC connector, -40°C to 85°C, DDM
SPB23010102B SFP+ Single Fibre, Tx 1270nm (DFB) , Rx 1330nm (PIN), maximum distance 10km,
power budget 9dB, 10x Gigabit Ethernet, LC connector, Gen B, -40°C to 85°C, DDM
SPB2301010GD SFP+ Single Fibre, Tx 1270nm (DFB) , Rx 1330nm (PIN), maximum distance 10km,
power budget 9dB, 10x Gigabit Ethernet, LC connector, 0°C to 70°C, DDM, Specific Firmware
SPB2301010AD SFP+ Single Fibre, Tx 1270nm (DFB) , Rx 1330nm (PIN), maximum distance 10km,
power budget 9dB, 10x Gigabit Ethernet, LC connector, 0°C to 70°C, DDM, Specific Firmware

10. Document Revision Information

Revision Description
A Initial release
B Specification updated to include 8x Fiber Channel compatibility
C Ordering information table updated with the “G” and “A” versions
D Specification updated to include CPRI compatibility
E Gen B variants added. Extended temperature variant removed

Skylane Optics® supplies a broad range of optical

transceivers. Our engineers work closely with our
customers to find the best solutions for every application.
We are committed to provide high quality products and Beyond
services to our customers. Quality

For questions on this product please contact:

[email protected]
Reliable
Alliance

Performing
Smartly

Specification subject to change without notice 4