Instruction Manual: LKH Centrifugal Pump

Instruction Manual
LKH Centrifugal Pump
ESE00698-EN13 2009-12
Original manual
Table of contents
The information herein is correct at the time of issue but may be subject to change without prior notice
1. EC Declaration of Conformity ....................................................................... 5
2. Safety .................................................................................................... 6
2.1. Important information ............................................................................. 6
2.2. Warning signs ..................................................................................... 6
2.3. Safety precautions ................................................................................ 7
3. Installation .............................................................................................. 8
3.1. Unpacking/Delivery ............................................................................... 8
3.2. Installation ......................................................................................... 9
3.3. Pre-use check - Pump without/with impeller screw ........................................... 10
4. Operation ............................................................................................... 11
4.1. Operation/Control ................................................................................. 11
4.2. Fault finding ....................................................................................... 13
4.3. Recommended cleaning ......................................................................... 14
5. Maintenance ........................................................................................... 15
5.1. General maintenance ............................................................................. 15
5.2. Dismantling of pump/shaft seals ................................................................ 17
5.3. Assembly of pump/single shaft seal ............................................................ 19
5.4. Assembly of pump/flushed shaft seal ........................................................... 21
5.5. Assembly of pump/double mechanical shaft seal ............................................. 23
5.6. Adjustment of shaft (LKH-5) ..................................................................... 25
5.7. Adjustment of shaft (LKH-10 to -90) ............................................................ 27
5.8. Cleaning Procedure ............................................................................... 29
6. Technical data ......................................................................................... 30

6.1. Technical data ..................................................................................... 30
6.2. Relubrication Intervals ............................................................................ 31
6.3. Addendum ......................................................................................... 32
7. Parts list and Service Kits ........................................................................... 33

7.1. LKH-5 Sanitary Version .......................................................................... 33
7.2. LKH-10, -15, -20, -25, -35, -40, -50, -60 Sanitary Version .................................. 34
7.3. LKH-70 - 90 Sanitary Version ................................................................... 35
7.4. LKH-5 Centrifugal Pump Single, Flushed and Double Mechanical Shaft Seal .............. 36
7.5. LKH-10 Centrifugal Pump Single, Flushed and Double Mechanical Shaft Seal ............ 38
7.14. LKH 5-60 Centrifugal Pumps, Shaft Seals ..................................................... 56
3
Table of contents
The information herein is correct at the time of issue but may be subject to change without prior notice
7.20. LKH-70, LKH-75, LKH-80, LKH-85 and LKH-90 Centrifugal Pump, Shaft Seal ........... 68
4
1 EC Declaration of Conformity
The designated company
Alfa Laval
Company Name
Albuen 31, DK-6000 Kolding, Denmark

Address
+45 79 32 22 00
Phone No.
hereby declare that
Pump LKH
Denomination Type Year
is in conformity with the following directives with amendments:

- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
- Machinery Directive 2006/42/EC
The technical construction file is retained at the above address
Manager, Product Center Fluid Handling Bjarne Søndergaard

Title Name
Alfa Laval Kolding

Company Signature
Designation
5
2 Safety
Unsafe practices and other important information are emphasized in this manual.
Warnings are emphasized by means of special signs.
Always read the manual before using the pump!
2.1 Important information
WARNING
Indicates that special procedures must be followed to avoid severe personal injury.
CAUTION
Indicates that special procedures must be followed to avoid damage to the pump.
NOTE
Indicates important information to simplify or clarify procedures.
2.2 Warning signs
General warning:
Dangerous electrical voltage:
Caustic agents:
Recycling information.
• Unpacking
- Packing material consists of wood, plastics, cardboard boxes and in some cases metal straps.
- Wood and cardboard boxes can be reused, recycled or used for energy recovery.
- Plastics should be recycled or burnt at a licensed waste incineration plant.
- Metal straps should be sent for material recycling.
• Maintenance
- During maintenance oil and wear parts in the machine are replaced.
- All metal parts should be sent for material recycling.
- Worn out or defective electronic parts should be sent to a licensed handler for material recycling.
- Oil and all non metal wear parts must be taken care of in agreement with local regulations.
• Scrapping
- At end of use, the equipment shall be recycled according to relevant, local regulations. Beside the equipment itself, any
hazardous residues from the process liquid must be considered and dealt with in a proper manner. When in doubt, or in the
absence of local regulations, please contact the local Alfa Laval sales company.
6
2 Safety
All warnings in the manual are summarized on this page.
Pay special attention to the instructions below so that severe personal injury and/or damage to the pump are avoided.
2.3 Safety precautions
Installation:
Always read the technical data thoroughly. (See chapter 6 Technical data)
Always use a lifting crane when handling the pump.
Pump without impeller screw:

Always remove the impeller before checking the direction of rotation.
Never start the pump if the impeller is fitted and the pump casing is removed.
Pump with Impeller screw:

Never start in the wrong direction of rotation with liquid in the pump.
Always have the pump electrically connected by authorized personnel.
Always have the pump electrically connected by authorized personnel. (See the motor instruction)
Operation:
Never run the pump when partially installed or not completely assembled
Necessary precautions must be taken if leakage occurs as this can lead to hazardous situations
Never touch the pump or the pipelines when pumping hot liquids or when sterilising.
Never run the pump with both the suction side and the pressure side blocked.
Always handle lye and acid with great care.
Maintenance:
Never service the pump when it is hot.
The pump and the pipelines must n ever be pressurised when the pump is serviced.
Motors with grease nipples:

Remember lubrication according to information plate/label on the motor.
Always disconnect the power supply when servicing the pump.
Transportation:
Transportation of the pump or the pump unit:
Never lift or elevate in any way other than described in this manual
Always drain the pump head and accessories of any liquid
Always ensure that no leakage of lubricants can occur
Always transport the pump in it’s upright position
Always ensure that the unit is securely fixed during transportation
Always use original packaging or similar during transportation
7
3 Installation
The instruction manual is part of the delivery. Study the instructions carefully.
The large pump sizes are very heavy.
Alfa Laval therefore recommends the use of a lifting crane when handling the pump.
3.1 Unpacking/Delivery
Step 1 Check the delivery for:

Always use a lifting crane when handling the pump (see technical 1. Complete pump.
data). 2. Delivery note.
3. Motor instructions.
CAUTION
Alfa Laval cannot be held responsible for incorrect unpacking.
Step 2
Remove possible packing materials from the inlet and the outlet.
Avoid damaging the inlet and the outlet.
Avoid damaging the connections for flushing liquid, if supplied. Remove
packing
materials!
TD 200-120_1
Caution!
Step 3 Inspection!
Inspect the pump for visible transport damages.
TD 200-120_1
Step 4 Remove the shroud before lifting!

Always remove the shroud, if fitted, before lifting the pump.
Step 5
ONLY LKH-85 and LKH-90
Do N OT use eyebolt in casing to lift the pump. The eyebolt is
only for casing removal.
8
3 Installation
Study the instructions carefully and pay special attention to the warnings! Always check the pump before operation.
- See pre-use check in section 3.3 Pre-use check - Pump without/with impeller screw.
The large pump sizes are very heavy. Alfa Laval therefore recommends the use of a lifting crane when handling the pump.
3.2 Installation
Step 1
Always have the pump electrically connected by

Always read the technical data thoroughly. authorized personnel.
(See chaper 6 Technical data) (see the motor instructions).
CAUTION
Alfa Laval cannot be held responsible for incorrect
Always use a lifting crane when handling the pump. installation.
(See chaper 6 Technical data)
Step 2
Ensure at least 0.5 m (1.6 ft) clearance around the pump.
Step 3
Check that the flow direction is correct.
O: Outlet
I: Inlet
Correct!
S tep 4 Remember seal rings!

1. Ensure that the pipelines are routed correctly.
2. Ensure that the connections are tight.
Few bends
Correct!
S tep 5
Avoid stressing the pump.
Pay special attention to:
- Vibrations.
- Thermal expansion of the tubes.
- Excessive welding.
- Overloading of the pipelines.
9
3 Installation
Study the instructions carefully and pay special attention to the warnings!
LKH-5 to -60 is without impeller screw as standard but can be supplied with one.
Check the direction of rotation of the impeller before operation.
- See the indication label on the pump.
3.3 Pre-use check - Pump without/with impeller screw
Step 1
Always remove the impeller before checking the direction of

rotation.
Never start the pump if the impeller is fitted and the pump casing
is removed.
1.
A. LKH-5: Remove screws (56), spring washers (56a), clamps
(55+55a) and pump casing (29).
B. LKH-10 to -90: Remove cap nuts (24), washers (24a) and
pump casing (29).
2. Remove impeller (27) (see also instruction in section 5.3
Assembly of pump/single shaft seal).
S tep 2 See the indication label!

1. Start and stop the motor momentarily.
2. Ensure that the direction of rotation of the stub shaft (7) is
anticlockwise as viewed from the inlet side. Correct!
Stub shaft
Step 3
Fit and tighten impeller (27).
S tep 4
1. Fit pump casing (29).
2.
A. LKH-5: Fit clamps (55+55a), spring washers (56a) and
tighten screws (56)
B. LKH-10 to -90: Fit washers (24a) and tighten cap nuts (24),
according to torque values in chapter 6.3 Addendum
Step 1 See the indication label!

Pump with impeller screw
Correct
Never start in the wrong direction of rotation with liquid in the
pump.
1. Start and stop the motor momentarily.
2. Ensure that the direction of rotation of the motor fan is View from rear end of
clockwise as viewed from the rear end of the motor. motor
10
4 Operation
The pump is fitted with a warning label indicating correct throttling
4.1 Operation/Control
Step 1
Always read the technical data thoroughly.

See chapter 6 Technical data
CAUTION
Alfa Laval cannot be held responsible for incorrect
operation/control.
Step 2 Burning danger!
Never touch the pump or the pipelines when pumping hot liquids
or when sterilising.
Step 3 Explosion danger!
Never run the pump with both the suction side and the pressure
side blocked.
S tep 4 Do not run dry! See the warning

CAUTION label!
The shaft seal must not run dry.
Correct!
CAUTION
Never throttle the inlet side.
TD 200-129_1
Wrong
11
4 Operation
The pump is fitted with a warning label indicating correct throttling
Step 5 Correct!
O
Flushed shaft seal:
1. Connect the inlet of the flushing liquid correctly. R 1/8” (BSP)
2. Regulate the water supply correctly.
3. Observe the steam data.
For LKH-85: connect inlet/outlet of the flushing liquid directly

on the flushing housing. TD 200-130_1
Tmax = 100ºC
I
O: Free outlet Pmax = 1 bar
I: Inlet
S tep 6 Throttling!
Control:
Reduce the capacity and the power consumption by means of:
- Throttling the pressure side of the pump.
- Reducing the impeller diameter.
- Reducing the speed of the motor.
12
4 Operation
Pay attention to possible faults.
Study the instructions carefully.
4.2 Fault finding
NOTE!
Study the maintenance instructions carefully before replacing worn parts. - See section 5.1 General maintenance
Problem Cause/result Remedy
Overloaded motor - Pumping of viscous liquids - Larger motor or smaller impeller

- Pumping of liquids with high density
- Low outlet pressure (counter pressure) - Higher counter pressure (throttling)
- Lamination of precipitates from the - Frequent cleaning
liquid
Cavitation:
- Damage - Low inlet pressure - Increase the inlet pressure
- Pressure reduction (sometimes to - High liquid temperature - Reduce the liquid temperature
zero)
- Increasing of the noise level - Reduce the pressure drop before the
pump
- Reduce speed
Leaking shaft seal - Dry run (See 4.1 Operation/Control) Replace:

All wearing parts (See 5.1 General
maintenance)
- Incorrect rubber grade If necessary:
- Change rubber grade
- Abrasive particles in the liquid - Select stationary and rotating seal ring
in Silicon Carbide/Silicon Carbide
Leaking seals Incorrect rubber grade Replace with seals of a different rubber
grade
13
4 Operation
The pump is designed for cleaning in place (CIP). CIP = Cleaning In Place.
NaOH = Caustic Soda.
HNO3 = Nitric acid.
4.3 Recommended cleaning
Step 1 Caustic danger!
Always handle lye and acid with great care.
Always use rubber gloves! Always use protective

goggles!
Never touch the pump or the pipelines when sterilizing.
Step 3
Examples of cleaning agents: Use clean water, free from

chlorides.
1. 1% by weight NaOH at 70°C (158°F).
1 kg (2.2 lb) + 100 l (26.4 gal) = Cleaning agent.
NaOH water
2.2 l (0.6 gal) + 100 l (26.4 gal) = Cleaning agent.

33%NaOH water
2. 0.5% by weight HNO3 at 70°C (158°F).

0.7 l (0.2 gal) + 100 l (26.4 gal) = Cleaning agent.
53% HNO3 water
Step 4
1. Avoid excessive concentration of the cleaning agent
Dose gradually!
2. Adjust the cleaning flow to the process
Sterilization of milk/viscous liquids
Increase the cleaning flow!
Step 5 Always rinse!
Always rinse well with clean water after using a cleaning agent.
NOTE
The cleaning agents must be stored/disposed of in accordance Water Cleaning agent
with current rules/directives.
14
5 Maintenance
Maintain the pump carefully. Study the instructions carefully and pay special attention to the warnings!
Always keep spare shaft seals and rubber seals in stock.
See separate motor instructions.
Check the pump for smooth operation after service.
5.1 General maintenance
Step 1
Always read the technical data thoroughly.

(See chaper 6 Technical data)
Always disconnect the power supply when servicing the pump.
NOTE
All scrap must be stored/discharged in accordance with current
rules/directives.
Never service the pump when it is hot.
Step 3 Atmospherie pressure

required!
Never service the pump with pump and pipelines under pressure.
CAUTION
Fit the electrical connections correctly if they have been removed
from the motor during service.
(see 3.3 Pre-use check - Pump without/with impeller screw)
CAUTION
Pay special attention to the warnings!
Step 4
Recommended spare parts:
Service kits (see chapter 7 Parts list and Service Kits).
Order Service Kits from Service kits list (see chapter 7 Parts list
and Service Kits).
Ordering spare parts

Contact the Sales Department.
15
5 Maintenance
Maintain the pump carefully. Study the instructions carefully and pay special attention to the warnings!
Always keep spare shaft seals and rubber seals in stock.
See separate motor instructions.
Check the pump for smooth operation after service.
Shaft seal Rubber seals Motor bearings
Preventive maintenance R eplace after 12 months: Replace when replacing the

(one-shift) Complete shaft seal shaft seal
Maintenance after leakage Replace at the end of the Replace when replacing the
(leakage normally starts slowly) day: Complete shaft seal shaft seal
Planned maintenance - Regular inspection for Replace when replacing the Yearly inspection is
leakage and smooth shaft seal recommended
operation - Replace complete bearing
- Keep a record of the pump if worn
- Use the statistics for - Ensure that the bearing is
planning of inspections axially locked (See motor
instructions)
Replace after leakage:
Complete shaft seal
Lubrication Before fitting Before fitting See section 6.2 Relubrication

Lubricate the O-rings with Silicone grease or silicone oil Intervals
silicone grease or silicone oil
Pre-use check
CAUTION!
Fit the electrical connections correctly if they have been removed from the motor during service. (See 3.3 Pre-use check -
Pump without/with impeller screw).
Pay special attention to warnings!
1. Start and stop the motor momentarily
2. Ensure that the pump operates smoothly.
16
5 Maintenance
Study the instructions carefully. The items refer to the parts list and service kits section.
Handle scrap correctly.
: Relates to the shaft seal.
5.2 Dismantling of pump/shaft seals
Step 1
1.
A. LKH-5: Remove screws (56), spring washers (56a), clamps
(55+55a) and pump casing (29).
B. LKH-10 to 90: Unscrew cap nuts (24) and remove washers
(24a) and pump casing (29).
LKH-85 and LKH-90
S tep 2
Flushed / Double Mechanical shaft seal:
Unscrew tubes (42) using a spanner.
S tep 3
Remove screw (23) and safety guard (22).
Step 4 Counterhold
1. Remove impeller screw (36), if fitted. with a
2. Remove impeller (27). If necessary, loosen the impeller by screwdriver!
knocking gently on the impeller vanes.
3. Remove the O-ring (38) from the impeller, if fitted.
If necessary!
S tep 5
1. Pull off the O-ring (26) from back plate (25).
2. Unscrew nuts (20) and remove washers (21) and the back plate.
17
5 Maintenance
Step 6 Use the tool

1. Remove the stationary seal ring (11). supplied
2. Remove the O-ring (12) from back plate (25).
Left hand
TD 200-462 thread!
S tep 7
Flushed shaft seal:
1. Remove screws (41) and seal housing (40).
2. Pull out lip seal (43) from the seal housing.
TD 200-390_1
Step 8
Double mechanical shaft seal:
1. Remove screws (41) and seal housing (40a).
2. Remove rotating seal rings (14) and drive ring (52) from spring
(13).
3. Remove O-rings (15) from rotating seal rings (14).
4. LKH-70 to 90: Remove cups (54) from rotating seal rings.
S tep 9
Double mechanical shaft seal:
1. Remove stationary seal ring (51) from seal housing (40a).
2. Remove O-ring (50) from stationary seal ring (51).
3. Remove O-ring (44) from seal housing (40a).
TD 200-391_1
Step 10
1. Remove the complete shaft seal from stub shaft (7).
2. Remove spring (13) and rotating seal ring (14) from the drive
ring (10).
TD 234-021_1
18
5 Maintenance
5.3 Assembly of pump/single shaft seal
Step 1
1. Remove spring (13).
NOTE!
Make sure that O-ring (15) has max. clearance from the sealing
surface.
S tep 2
1. Refit spring (13) on rotating seal ring (14).
2. Fit the spring and the rotating seal ring on drive ring (10).
CAUTION
Ensure that the driver on the drive ring enters the notch in the
rotating seal ring. TD 200-393_1
S tep 3
Fit the complete shaft seal on stub shaft (7).
NOTE!
Make sure that connex pin (8) on the stub shaft enters the notch in
drive ring (10).
Step 4
1. Fit O-ring (12) on stationary seal ring (11) and lubricate.
Use the tool
2. Screw the stationary seal ring into back plate (25).
supplied
CAUTION
Only tighten by hand to avoid deforming the stationary seal ring.
(Max 7Nm/5 lbf-ft)
Left hand
TD 200-462 thread!
S tep 5
1. Clean the sealing surfaces with contact cleaner before fitting
back plate (25).
2. Carefully guide the back plate onto adaptor (16).
3. Fit washers (21) and nuts (20).
TD 234-009_1
Step 6
Lubricate O-ring (26) and slide it onto back plate (25).
TD 234-026_1
19
5 Maintenance
Step 7
1. Lubricate O-ring (38) and fit it in impeller (37), if impeller screw
is used.
2. Lubricate impeller hub with silicone grease or oil.
3. Screw the impeller onto stub shaft (7).
4. Fit impeller screw (39) and tighten, if used.
Torque - 5-60 = 20 Nm (7.4 lbf-ft)
Torque - 70-90 = 50 Nm (37 lbf-ft)
S tep 8
Fit safety guards (22) and screw (23) and tighten.
Step 9
1.
A. LKH-5: Fit pump casing (29), clamps (55+55a), spring
washers (56a) and screws (56).
B. LKH-10 to-90: Fit pump casing (29), washers (24a) and
cap nuts (24).
2. Adjust pump casing to the right position.
3.
A. LKH-5: Tighten nuts (20) for back plate (25) and tighten
screws (56).
B. LKH-10 to -90: Tighten nuts (20) for back plate (25) and
tighten cap nuts (24), according to torque values in chapter LKH-85 and LKH-90
6.3 Addendum.
20
5 Maintenance
Lubricate the rubber seals before fitting them.
5.4 Assembly of pump/flushed shaft seal
Step 1 Use ø63 mm tube!

Flushed shaft seal :
LKH-5 to -60 use ø63mm tube
LKH-70 to -90 press in lip seal by hand
1. Fit lip seal (43) in seal housing (40).
2. Lubricate O-ring (44) and slide onto the seal housing (40).
3. Fit the seal housing on back plate (25) and tighten screws (41).
Step 2
1. Lubricate O-ring (45) and fit it in drive ring (10).
2. Fit spring (13) and rotating seal ring (14) on the drive ring.
CAUTION
Ensure that the driver on the drive ring enters the notch in the
rotating seal ring. TD 200-393_1
S tep 3
Fit complete shaft seal on stub shaft (7) so that connex pin (8) on
the stub shaft enters the notch in drive ring (10).
Step 4
1. Carefully guide back plate (25) onto adaptor (16).
TD 234-027_1
Step 5
TD 234-026_1
Step 6
is used.
2. Lubricate the impeller hub with silicone grease or oil.
3. Screw impeller (27) onto stub shaft (7).
Torque - 5-60 20 Nm (7.4 lbf-ft)
Torque - 70-90 50 Nm (37 lbf-ft)
21
5 Maintenance
Step 7
1. Screw tubes (42) into seal housing (40).
2. Tighten with a spanner.
TD 234-017_1
Step 8
Fit safety guard (22) and screw (23) and tighten.
Step 9
1.
A. LKH-5: Fit pump casing (29), clamps (55+55a), spring
washers (56a) and screws (56).
B. LKH-10 to-90: Fit pump casing (29).
2. Tighten nuts (20) for back plate (25).
3.
A. LKH-5: Tighten nuts (20) for back plate (25) and tighten
screws (56).
B. LKH-10 to -90: Fit washers (24a) and cap nuts (24)
and tighten, according to torque values in chapter 6.3
Addendum. LKH-85 and LKH-90
22
5 Maintenance
5.5 Assembly of pump/double mechanical shaft seal

Step 1
1. Fit O-rings (15) in rotating seal rings (14).

2. LKH-70 to -90: Fit cups (54) on rotating seal rings (14).
3. Fit spring (13) on one of the rotating seal rings (14) and
place the drive ring (52) in between.
Step 2 Only LKH-70-90

1. LKH-70 to -90: Turn the drive ring (52) in order to place it
correctly on the pump shaft (7).
2. Fit the second rotating ring (14) on the other end of the spring.
3. Place the parts on the stationary seal ring fitted in back plate
(25).
NOTE
Ensure that both drive pins on the drive ring enters the notches in
rotating seal rings.
Step 3
1. Lubricate O-ring (44) and slide onto seal housing (40a).
2. Lubricate O-ring (50) and fit on stationary seal ring (51) and fit
this in the seal housing.
TD 200-447_1
S tep 4
1. Clean the sealing surfaces with contact cleaner.
2. Fit seal housing (40a) on the back plate (25) and tighten screws
(41).
S tep 5
1. To enable fitting back plate (25) with the shaft seal remove
connex pin (8) from stub shaft (7) (if fitted).
2. Carefully guide the back plate onto adaptor (16).
TD 234-027_1
Step 6
TD 234-033_1
23
5 Maintenance
Step 7
is used.
2. Lubricate the impeller hub with silicone grease or oil.
3. Screw impeller (27) onto stub shaft (7).
Torque - 5-60 20 Nm (7.4 lbf-ft)
Torque - 70-90 50 Nm (37 lbf-ft)
S tep 8
1. Screw tubes (42) into seal housing (40a).
2. Tighten with a spanner.
TD 234-017_1
Step 9
Fit safety guard (22) and screw (23) and tighten.
Step 10
1. Fit pump casing (29).
2. Tighten nuts (20) for back plate (25).
3.
A. LKH-5: Fit clamps (55+55a), spring washers (56a) and
screws (56) and tighten.
B. LKH-10 to -90: Fit washers (24a) and cap nuts (24)
and tighten, according to torque values in chapter 6.3
Addendum.
LKH-85 and LKH-90
24
5 Maintenance
5.6 Adjustment of shaft (LKH-5)
Step 1
1. Loosen screws (6).
2. Pull off stub shaft (7).
See special cleaning procedure for tapped hole in stub shaft
page 29.
S tep 2 10-20 mm
1. Push stub shaft (7) onto the motor shaft. Screws (4) must fit (0.39-0.78 inch)
in keyway on the motor shaft.
2. Check that the clearance between the end of the stub shaft
and the motor flange is 10-20 mm (0.39 - 0.78 inch).
S tep 3
1. Tighten screws (4) lightly and evenly.
2. Ensure that stub shaft (7) can be moved on the motor shaft.
S tep 4
1. F or double mechanical shaft seal: Fit drive ring (52) on stub
shaft (7).
2. Fit back plate (25), washers (21) and nuts (20) and tighten.
S tep 5 LKH-5 = 0.5 mm (0.02 inch)

1. Fit impeller (27) on stub shaft (7).
2. Ensure that the clearance between the impeller and back plate
(25) is correct: 0.5 mm (0.02 inch) for LKH-5.
25
5 Maintenance
Step 6
Tighten screws (4) evenly to 18 Nm (13 lbf-ft).
26
5 Maintenance
5.7 Adjustment of shaft (LKH-10 to -90)
Step 1
1. Loosen screws (6).
2. Pull off stub shaft (7) together with compression rings (5a,5b).
See special cleaning procedure for tapped hole in stub shaft
page 29.
S tep 2 10-20 mm
1. Push stub shaft (7) together with compression rings (5a, 5b) (0.39-0.78 inch)
onto the motor shaft.
2. Check that the clearance between the end of the stub shaft
and the motor flange is 10-20 mm (0.39 - 0.78 inch).
Step 3
1. Tighten screws (6) lightly and evenly.
2. Ensure that stub shaft (7) can be moved on the motor shaft.
S tep 4
1. F or double mechanical shaft seal:
Fit drive ring (52) on stub shaft (7).
2. Fit back plate (25), washers (21) and nuts (20) and tighten.
Step 5 LKH-10 to -60 = 0.5 mm (0.02 inch)

1. Fit impeller (27) on stub shaft (7). LKH-70 to -90 = 1.0 mm (0.039 inch)
2. Ensure that the clearance between the impeller and back plate
(25) is correct: 0.5 mm (0.02 inch) for LKH-10 to 60 and 1.0
mm (0.039 inch) for LKH-70 to -90.
NOTE! If pump has been ordered with increased clearence
between impeller and backplate this additional clearence must be
taken into account when adjusting the shaft.
27
5 Maintenance
Step 6 Counterhold with a screwdriver

1. Remove impeller (27), back plate (25) and drive ring (52).
2. Tighten screws (6) evenly to 15 Nm (11 lbf-ft). 15Nm
(11 lbf-ft)
28
5 Maintenance
5.8 Cleaning Procedure
Cleaning Procedure for Soiled Impeller Screw Tapped Hole:

1. Remove stub shaft (7) per section 4 of Service manual.
2. Submerge and soak Stub Shaft for 5 minutes in COP tank with 2% caustic wash
3. Scrub the blind tapped impeller screw hole vigorously by plunging a clean 1/2” diameter sanitary bristle pipe brush in and out
of the hole for two minutes while submerged.
4. Soak Stub Shaft (7) in acid sanitizer for 5 minutes, then scrub blind tapped hole as described in step 3 above.
5. Rinse well with clean water and blow-dry blind tapped hole with clean air.
6. Swab test the inside of the tapped hole to determine cleanliness.
7. Should the swab test fail, repeat steps 2 thru 6 above until swab test is passed.
Should swab testing continue to fail, or time is of the essence, install a new (spare) Stub Shaft (7).
29
6 Technical data
It is important to observe the technical data during installation, operation and maintenance.
Inform the personnel about the technical data.
6.1 Technical data
Data
Max. inlet pressure LKH-5 : 600 kPa (6 bar) (87 psi )

LKH-10 to -80 (50 Hz): 1000 kPa (10 bar) (145 psi )
LKH-85 and LKH-90 (50 Hz): 500 kPa (5 bar) (72.5 psi)
LKH-10 to -60 (60 Hz): 1000 kPa (10 bar) (145 psi )
LKH-70, LKH-75, LKH-85, LKH-90 (60 Hz): 500 kPa (5 bar) (72.5 psi )
Temperature range -10o C to +140o C (EPDM) (14 to 284oF )
Noise level 60-80 dB (A)
Materials
Product wetted steel parts AISI 316L

Other steel parts AISI 304
Finish Semi-bright
Product wetted seals EPDM (standard)
Other O-rings EPDM
Alternative seals Nitrile (NBR), Fluorinated rubber (FPM) and FEP
Shaft seal
Seal types External single, flushed or double mechanical seal

Max. water pressure (flushed seal) Normally atmospheric (max. 1 bar) (max. 14.5 psi )
Water consumption (flushed seal) 0.25 - 0.5 l/min. (0.07-0.13 gl )
Max. water pressure LKH-5 to -60 (DMS) Normally atmospheric (max. 5 bar) (max. 72.5 psi )
Max. water pressure LKH-70 to -90 (DMS) Normally atmospheric (max. 3 bar) (max. 43.5 psi )
Water consumption (double mechanical seal) 0.25-0.5 l/min. (0.07-0.13 gl )
Material, stationary seal ring Acid resistent steel with sealing surface of Silicon Carbide
Material, rotating seal ring Carbon (standard) or Silicon Carbide
Material, O-rings EPDM (standard)
Alternative material, O-rings Nitrile (NBR), Fluorinated rubber (FPM) and FEP
Motor
Foot-flanged motor acc. to IEC metric standard 2 poles = 3000/3600 rpm. at 50/60 Hz IP55 (drain hole with labyrinth
plug), insulation class F
Motor sizes (kW), 50 Hz 0.75 - 1.1 - 1.5 - 2.2 - 3 - 4 - 5.5 - 7.5 - 11 - 15 -18.5 - 22 - 30 - 37 - 45 -
55 - 75 - 90 - 110 kW
Motor sizes (kW), 60 Hz 0.9 - 1.3 - 1.75 - 2.5 - 3.5 - 4.6 - 6.4 - 8.6 - 12.5 -17 - 21 - 25 - 35 - 43 -
52 - 63 - 86 - 105 - 125 kW.
Motor sizes (hp), 60 Hz 1.5 - 2.0 - 3.0 - 5.0 - 7.5 - 10.0 - 15.0 - 20.0 - 25.0 - 30.0 - 40.0 -
50.0 - 60.0 - 75.0 - 100.0 - 125.0 - 150.0 hp
Voltage and frequency
Voltage and frequency (standard) 3~, 50 Hz, 220-240V¨/380-420VY 4 kW

3~, 60 Hz, 250-280V¨/440-480VY 4.6 kW
3~, 50 Hz, 380-420V¨/660-690VY 5.5 kW
3~, 60 Hz, 440-480V¨ 6.3 kW
For further information - see PD-sheet.
30
6 Technical data
Relubrication interval 50 Hz (3000 rpm)/Relubrication interval 60 Hz (3600 rpm). (Vendor) quantity in D rive E nd/quantity in
Non D rive E nd.
6.2 Relubrication Intervals
The table is for 100°C internal bearing temperature.an increase in temperature of 15°C (ambient or internal in bearings), will
reduce the greasing interval and bearing lifetime by 50%. Lubrication interval for vertically mounted pumps is half the value
stated in the table.
Frame Motor LKH-5 - 90 LKHP-10 - 60 LKH-122/P

size power LKHI-10 - 60* LKHI-10 - 60 LKH-123/P
(kW) LKH-110* LKH-110 LKH-124/P
LKHSP 50/60 Hz 50/60 Hz
LKH Ultra Pure
50/60 Hz
80 0.75 Permanently lubricated (ABB) Not available Not available
90 1.5 Permanently lubricated (ABB) Permanently lubricated (ABB) Not available
90 2.2 Permanently lubricated (ABB) Permanently lubricated (ABB) Not available
112 4.0 Permanently lubricated (ABB) 4300h/3300h Not available
DE/NDE:10g (Brook, ABB)
160 11 Permanently lubricated (ABB) 3100h/2300h Not available
200 30 Permanently lubricated (ABB) 4000h/2800h 4000h/2800h
4300h/3500h DE/NDE: 23g (Brook) DE/NDE:45g (Brook, ABB) DE/NDE:45g (Brook, ABB)
250 55 Permanently lubricated (ABB) Not available 3500h/2500h
3950h/3200h DE/NDE: 26g (Brook) DE/NDE:45g (Brook, ABB)
250 75 Permanently lubricated (ABB) Not available 3500h/2500h
3950h/3200h DE/NDE: 26g (Brook) DE/NDE.45g (Brook, ABB)
* inlet pressure < 10 bar (145 psi )
Recommended grease types: - Mobilgrease HP - Shell Lipex EP2 - Castrol LMX

- ESSO Unirex N3 - SKF LGHT3
31
6 Technical data
6.3 Addendum
Section 1
Tightening torques
Below table specifies the tightening torques for the screws, bolts and nuts in this pump.
Always use below torques if no other values are stated. This can be a matter of personal safety.
Size Tightening torgue
Nm lbf-ft
M8 20 14.8
M10 40 29.5
M12 67 49.0
M14 110 81.0
Section 2
Noise
Pump Type Sound pressure level (dBA)
LKH-5 60
LKH-10 69
LKH-15 72
LKH-20 70
LKH-25 74
LKH-35 71
LKH-40 75
LKH-45 70
LKH-50 75
LKH-60 77
LKH-70 88
LKH-75 79
LKH-85 86
LKH-90 75
The noise measurements are carried out with original motor and shroud, approximately at the Best Efficiency Point (BEP) with
water at ambient temperature and at 50Hz.
Very often the noise level generated by the flow through the process system (eg. valves, pipes, tanks etc.) is much higher than
what is generated by the pump itself. Therefore it is important to consider the noise level from the total system and take the
necessary percussions with regards to personal safety if required.
32
7 Parts list and Service Kits
The drawing shows LKH pump, sanitary version.
The items refer to the parts lists in the following sections 7.4 LKH-5 Centrifugal Pump Single, Flushed and Double Mechanical
Shaft Seal
7.1 LKH-5 Sanitary Version
Impeller screw Ftting of legs Fitting of back plate

0.75-11 kW
Flushed shaft seal Double mechanical shaft seal
33
Shaft Seal to 7.13 LKH-60 Centrifugal Pump Single, Flushed and Double Mechanical Shaft Seal
7.2 LKH-10, -15, -20, -25, -35, -40, -50, -60 Sanitary Version
Impeller screw Only used for 0.75, 1.1 and 3 kW Fitting of back plate
Fitting of legs
34
Shaft Seal to 7.19 LKH-90 Centrifugal Pump Single, Flushed and Double Mechanical Shaft Seal
7.3 LKH-70 - 90 Sanitary Version
LKH-85 and LKH-90

LKH-75: USA version only, no shroud, US leg set.
Fitting of back plate Fitting of legs 55 - 110 kW
35
The drawing and the parts list include all items.
7.4 LKH-5 Centrifugal Pump Single, Flushed and Double Mechanical Shaft Seal
DMSS = Double Mechanical Shaft Seal. FSS = Flushed Shaft Seal
DM
SS
FSS
Alternatives
36
Parts list Service kits

Denomination C /SIC SIC/SIC
Pos. Qty Denomination
Service kit for single shaft seal
1 1 Motor
2 1 Shroud Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2302 9611-92-2522
2a 1 Edge list Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2303 9611-92-2523
3 4 Screw Service kit, FPM. . . . . . . . . . . . . . . . . . 9611-92-2304 9611-92-2524
4 2 Screw
7 1 Shaft and pin (pos.8) Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2305 9611-92-2525
8 1 Connex pin
10 1 Drive ring Service kit for single shaft seal and impeller screw
16 1 Adaptor
17 4 Screw for adaptor Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2306 9611-92-2526
18 4 Nut for adaptor Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2307 9611-92-2527
19 4 Washer for adaptor Service kit, FPM . . . . . . . . . . . . . . . . . ۫ 9611-92-2308 9611-92-2528
20 2 Nut Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2309 9611-92-2529
21 2 Washer
22 1 Safety guard
23 1 Screw for safety guard Service kit for flushed shaft seal
25 1 Back plate
Service kit, EPDM (Std.) . . . . . . . . . { 9611-92-2310 9611-92-2530
26 ۫{¨Ÿ 1 O-ring
az Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2311 9611-92-2531
27 1 Impeller Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2312 9611-92-2532
29 1 Pump casing
Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2313 9611-92-2533
30a 1 Support bar, right
30b 1 Support bar, left
31 4 leg Service kit for flushed shaft seal and impeller screw
32 4 Screw 9611-92-2314 9611-92-2534
Service kit, EPDM (Std.) . . . . . . . . .
33 4 Nut
34 4 Spring washer Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2315 9611-92-2535
35 4 Screw Service kit, FPM . . . . . . . . . . . . . . . . . 9611-92-2316 9611-92-2536
35a 4 Washer Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2317 9611-92-2537
36 1 Impeller screw
37 1 Impeller for impeller screw
38 ۫Ÿz 1 O-ring Service kit for double mechanical shaft seal C/SIC
39 4 Nut Service kit, EPDM (Std.) . . . . . . . . . ¨ 9611-92-2318 a 9611-92-2538
40 1 Seal housing
40a 1 Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2319 a 9611-92-2539
Seal housing
41 2 Screw for seal housing Service kit, FPM. . . . . . . . . . . . . . . . . . ¨ 9611-92-2320 a 9611-92-2540
42 2 Tube Service kit, FEP . . . . . . . . . . . . . . . . . . ¨ 9611-92-2321 a 9611-92-2541

55 1 Upper clamp
55a 1 Lower clamp
56 2 Service kit for double mechanical shaft seal and impeller screw
Screw
56a 2 Spring washer Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2322 z 9611-92-2542
Service kit, NBR . . . . . . . . . . . . . . . . . Ÿ 9611-92-2323 z 9611-92-2543
Service kit, FPM. . . . . . . . . . . . . . . . . . Ÿ 9611-92-2324 z 9611-92-2544
Service kit, FEP . . . . . . . . . . . . . . . . . . Ÿ 9611-92-2325 z 9611-92-2545
Parts marked with ۫{¨Ÿaz are included in the service kits.

Recommended Spare Parts: Service kits.
Shaft seal: See page 56
Conversion kit, single to flushed shaft seal EPDM C/SIC 9611-92-2042 = Pos. 10+40b+41+42+43+44+45
Conversion kit, single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos.13+ 14+15+40a+41+42+44+50+51+52
Conversion kit, flushed to double mechanical shaft seal EPDM C/SIC 9611-92-2176 = Pos.13+ 14+40a+50+51+52
900010/2
37
DM
SS
FSS
Impeller with Inducer Alternatives
38

1 1 Motor
2a 1 Edge list Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2072 9611-92-2546
2 1 Shroud complete Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2073 9611-92-2547
5a 1 Compression ring with thread
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2075 9611-92-2549
5b 1 Compression ring without thread
6 6 Screw
6a 6 Washer Service kit for single shaft seal and impeller screw
7 1 Shaft
8 1 Connex pin Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2114 9611-92-2550
9 1 Retaining ring Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2115 9611-92-2551
10 1 Drive ring Service kit, FPM . . . . . . . . . . . . . . . . . ۫ 9611-92-2116 9611-92-2552
16 1 Adaptor Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2117 9611-92-2553
17 4 Screw for adaptor
18 4 Nut for adaptor
19 4 Washer for adaptor Service kit for flushed shaft seal
20 2 Nut Service kit, EPDM (Std.) . . . . . . . . . { 9611-92-2076 9611-92-2554
21 2 Washer
22 1 Safety guard Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2077 9611-92-2555
23 1 Screw for safety guard Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2078 9611-92-2556
24 6 Cap nut Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2079 9611-92-2557
24a 6 Washer
25 1 Back plate
26 ۫{¨Ÿ 1 O-ring Service kit for flushed shaft seal and impeller screw
az
27 1 Impeller Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2118 9611-92-2558
28 6 Bolt Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2119 9611-92-2559
29 1 Pump casing Service kit, FPM . . . . . . . . . . . . . . . . . 9611-92-2120 9611-92-2560
30a 1 Support bar, right Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2121 9611-92-2561
31 4 Leg
32 4 Screw Service kit for double mechanical shaft seal
34 4 Spring washer
35 4 Screw Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2207 a 9611-92-2563
35a 4 Washer Service kit, FPM. . . . . . . . . . . . . . . . . . ¨ 9611-92-2208 a 9611-92-2564
36 1 Impeller screw Service kit, FEP . . . . . . . . . . . . . . . . . . ¨ 9611-92-2209 a 9611-92-2565
38 ۫Ÿz 1 O-ring
39 4 Nut Service kit for double mechanical shaft seal and impeller screw
40 1 Seal housing Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2210 z 9611-92-2566
40a 1 Seal housing
41 2 Screw for seal housing
42 2 Tube
57 1 Inducer Service kit, FEP . . . . . . . . . . . . . . . . . . Ÿ 9611-92-2213 z 9611-92-2569
Parts marked with ۫{¨Ÿaz are included in the service kits. Recommended Spare Parts: Service kits. Shaft seal: See page 56
Conversion kit, single to flushed shaft seal EPDM C/SIC 9611-92-2042 = Pos. 10+40+41+42+43+44+45
Conversion kit single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos.13+ 14+15+40a+41+42+44+50+51+52
Conversion kit single to double mechanical shaft seal EPDM SIC/SIC 9611-92-2326 = Pos. 13+14+15+40a+41+42+44+50+51+52
Replace to inducer (For pump with impellerscrew) please order pos. 7+57+38
Replace to inducer (For pump without impellerscrew) please order pos. 7+57+37+38
900009/3
39
DM
SS
FSS
40

1 1 Motor
2 1 Shroud complete Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2073 9611-92-2547
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2075 9611-92-2549
6a 6 Washer
6 6 Screw Service kit for single shaft seal and impeller screw
7 1 Shaft
10 1 Drive ring Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2115 9611-92-2551
16 1 Adaptor Service kit, FPM . . . . . . . . . . . . . . . . . ۫ 9611-92-2116 9611-92-2552
17 4 Screw for adaptor Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2117 9611-92-2553
19 4 Washer for adaptor
20 2 Nut Service kit for flushed shaft seal
21 2 Washer
22 1 Safety guard Service kit, EPDM (Std.) . . . . . . . . . { 9611-92-2076 9611-92-2554
23 1 Screw for safety guard Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2077 9611-92-2555
24 6 Cap nut Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2078 9611-92-2556
24a 6 Washer Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2079 9611-92-2557
25 1 Back plate
26 ۫{¨Ÿ 1 O-ring
az Service kit for flushed shaft seal and impeller screw
27 1 Impeller
28 6 Bolt Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2118 9611-92-2558
29 1 Pump casing Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2119 9611-92-2559
30a 1 Support bar, right Service kit, FPM . . . . . . . . . . . . . . . . . 9611-92-2120 9611-92-2560
30b 1 Support bar, left Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2121 9611-92-2561
31 4 Leg
32 4 Screw
33 4 Nut Service kit for double mechanical shaft seal
34 4 Spring washer
Service kit, EPDM (Std.) . . . . . . . . . ¨ 9611-92-2206 a 9611-92-2562
35 4 Screw
35a 4 Washer Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2207 a 9611-92-2563
36 1 Impeller screw Service kit, FPM. . . . . . . . . . . . . . . . . . ¨ 9611-92-2208 a 9611-92-2564
37 1 Impeller for impeller screw Service kit, FEP . . . . . . . . . . . . . . . . . . ¨ 9611-92-2209 a 9611-92-2565
38 ۫Ÿz 1 O-ring
39 4 Nut
40 1 Seal housing Service kit for double mechanical shaft seal and impeller screw
40a 1 Seal housing Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2210 z 9611-92-2566
42 2 Tube
46 4 Distance sleeve Service kit, FPM. . . . . . . . . . . . . . . . . . Ÿ 9611-92-2212 z 9611-92-2568
57 1 Inducer Service kit, FEP . . . . . . . . . . . . . . . . . . Ÿ 9611-92-2213 z 9611-92-2569

Conversion kit single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos.13+ 14+15+40a+41+42+44+50+51+52
Conversion kit single to double mechanical shaft seal EPDM SIC/SIC 9611-92-2326 = Pos.13+ 14+15+40a+41+42+44+50+51+52
Conversion kit, flushed to double mechanical shaft seal EPDM C/SIC 9611-92-2176 = Pos. 13+14+40a+50+51+52
Replace to inducer (for pump with impellerscrew) please order pos. 7+57+38
Replace to inducer (for pump without impellerscrew) please order pos. 7+57+37+38
900010/2
41
DM
SS
FSS
42

Denomination C /SiC SiC/SiC
1 1 Motor
2 1 Shroud complete Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2080 9611-92-2570
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2083 9611-92-2573
6 6 Screw
7 1 Shaft
9 1 Retaining ring Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2123 9611-92-2575
10 1 Drive ring Service kit, FPM . . . . . . . . . . . . . . . . . ۫ 9611-92-2124 9611-92-2576
16 1 Adaptor Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2125 9611-92-2577
19 4 Washer for adaptor Service kit for flushed shaft seal
21 2 Washer
22 1 Safety guard Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2085 9611-92-2579
23 1 Screw for safety guard Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2086 9611-92-2580
24 6 Cap nut Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2087 9611-92-2581
24a 6 Washer
25 1 Back plate
26 ۫{¨Ÿ 1 O-ring Service kit for flushed shaft seal and impeller screw
az
27 1 Impeller Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2126 9611-92-2582
28 6 Bolt Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2127 9611-92-2583
29 1 Pump casing Service kit, FPM . . . . . . . . . . . . . . . . . 9611-92-2128 9611-92-2584
30a 1 Support bar, right Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2129 9611-92-2585
31 4 Leg
32 4 Screw Service kit for double mechanical shaft seal
34 4 Spring washer
35 4 Screw Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2215 a 9611-92-2587
35a 4 Washer Service kit, FPM. . . . . . . . . . . . . . . . . . ¨ 9611-92-2216 a 9611-92-2588
36 1 Impeller screw Service kit, FEP . . . . . . . . . . . . . . . . . . ¨ 9611-92-2217 a 9611-92-2589
38 ۫Ÿz 1 O-ring EPDM
39 4 Nut Service kit for double mechanical shaft seal and impeller screw
40a 1 Seal housing
42 2 Tube
46 4 Distance sleeve Service kit, FEP . . . . . . . . . . . . . . . . . . Ÿ 9611-92-2221 z 9611-92-2593
57 1 Inducer

Conversion kit single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos. 13+14+15+40a+41+42+44+50+51+52
Conversion kit single to double mechanical shaft seal EPDM SIC/SIC 9611-92-2326 = Pos.13+ 14+15+40a+41+42+44+50+51+52
Replace to inducer (For pump with impeller screw) please order pos. 7+57+38
Replace to inducer (For pump without impeller screw) please order pos. 7+57+37+38.
900011/2
43
DM
SS
FSS
44

1 1 Motor
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2181 9611-92-2597
6 6 Screw
7 1 Shaft
21 2 Washer
25 1 Back plate
26 ۫{¨Ÿ 1 O-ring
27 1 Impeller
31 4 Leg
32 4 Screw
34 4 Spring washer
35 4 Screw
38 ۫Ÿz 1 O-ring
40 1 Seal housing
40a 1 Seal housing Service kit for double mechanical shaft seal and impeller screw
41 2 Screw for seal housing Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2226 z 9611-92-2614
42 2 Tube Service kit, NBR . . . . . . . . . . . . . . . . . Ÿ 9611-92-2227 z 9611-92-2615
46 4 Distance sleeve
57 1 Inducer Service kit, FPM. . . . . . . . . . . . . . . . . . Ÿ 9611-92-2228 z 9611-92-2616

Conversion kit single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos. 13+14+15+40a+41+42+44+50+51+52
Conversion kit single to double mechanical shaft seal EPDM SIC/SIC 9611-92-2326 = Pos. 13+14+15+40a+41+42+44+50+51+52
900012/3
45
DM
SS
FSS
46

1 1 Motor
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2181 9611-92-2597
6 6 Screw
7 1 Shaft
21 2 Washer
25 1 Back plate
26 ۫{¨Ÿ 1 O-ring
27 1 Impeller
31 4 Leg
32 4 Screw
34 4 Spring washer
35 4 Screw
38 ۫Ÿz 1 O-ring
40 1 Seal housing
40a 1 Seal housing Service kit for double mechanical shaft seal and impeller screw
41 2 Screw for seal housing Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2226 z 9611-92-2614
42 2 Tube Service kit, NBR . . . . . . . . . . . . . . . . . Ÿ 9611-92-2227 z 9611-92-2615
57 1 Inducer Service kit, FPM. . . . . . . . . . . . . . . . . . Ÿ 9611-92-2228 z 9611-92-2616

Conversion kit, single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos. 13+14+15+40a+41+42+44+50+51+52
Conversion kit, single to double mechanical shaft seal EPDM SIC/SIC 9611-92-2326 = Pos. 13+14+15+40a+41+42+44+50+51+52
900014/3
47
DM
SS
FSS
48

Service kits for single shaft seal
1 1 Motor
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2091 9611-92-2622
6 6 Screw
6a 6 Washer Service kits for single shaft seal and impeller screw
7 1 Shaft
Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2133 9611-92-2626
20 2 Nut Service kits for flushed shaft seal
21 2 Washer
25 1 Backplate
26 ۫{¨Ÿ 1 O-ring
az Service kits for flushed shaft seal and impeller screw
27 1 Impeller
Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2137 9611-92-2634
31 4 Leg
32 4 Screw
33 4 Nut Service kits for double mechanical shaft seal
34 4 Spring washer
35 4 Screw Service kit, EPDM (Std.) . . . . . . . . . ¨ 9611-92-2230 a 9611-92-2635
38 ۫Ÿz 1 O-ring
40a 1 Seal housing
46 4 Distance sleeve Service kits for double mechanical shaft seal and impeller screw
57 1 Inducer
Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2234 z 9611-92-2639
Conversion kit, single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos. 13+14+15+40a+41+42+44+ 50 +51+52
Conversion kit, single to double mechanical shaft seal EPDM SIC/SIC 9611-92-2326 = Pos.13+ 14+15+40a+41+42+44+ 50 +51+52
Replace to inducer (for pump with impellerscrew ) please order pos. 7+57+38
Replace to inducer (for pump without impellerscrew ) please order pos. 7+57+37+38
900015/4
49
DM
SS
FSS
50

1 1 Motor
2 1 Shroud complete Service kit, EPDM (std) . . . . . . . . . . 9611-92-2178 9611-92-2594
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2181 9611-92-2597
6 6 Screw
6a 6 washer Service kit for single shaft seal and impeller screw
7 1 Shaft
8 1 Connex pin Service kit, EPDM (std) . . . . . . . . . . ۫ 9611-92-2182 9611-92-2598
16 1 Adapter Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2180 9611-92-2596
17 4 Screw for adapter Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2181 9611-92-2597
18 4 Nut for adapter
19 4 washer for adapter
21 2 washer
22 1 Safety guard Service kit, EPDM (std) . . . . . . . . . . { 9611-92-2186 9611-92-2602
24a 6 washer Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2189 9611-92-2605
25 1 Back plate
26 ۫{¨Ÿ 1 O-ring
27 1 Impeller
28 6 Bolt Service kit, EPDM (std) . . . . . . . . . . 9611-92-2190 9611-92-2606
30b 1 Support bar, Left Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2193 9611-92-2609
31 4 Leg
32 4 Screw
34 4 Spring washer
Service kit, EPDM (std) . . . . . . . . . . ¨ 9611-92-2222 a 9611-92-2610
35 4 Screw
35a 4 washer Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2223 a 9611-92-2611
38 ۫Ÿz 1 O-ring
40 1 Seal housing
41 2 Screw for seal housing Service kit for double mechanical shaft seal and impeller screw
42 2 Tube Service kit, EPDM (std) . . . . . . . . . . Ÿ 9611-92-2226 z 9611-92-2614
57 1 Service kit, NBR . . . . . . . . . . . . . . . . . Ÿ 9611-92-2227 z 9611-92-2615
Inducer

Conversion kit, single to double mechanical shaft seal EPDM C/SIC 9611-92-2175 = Pos.13+ 14+15+40a+41+42+44+50+51+52
900016/3
51
DM
SS
FSS
52

1 1 Motor
1 Motor Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2088 9611-92-2619
2 1 Shroud Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2089 9611-92-2620
1 Shroud
Service kit, FPM. . . . . . . . . . . . . . . . . . 9611-92-2090 9611-92-2621
2a 1 Edge list
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2091 9611-92-2622
1 Edge list
3 4 Screw
5a 1 Compression ring with thread Service kit for single shaft seal and impeller screw
6 6 Screw Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2130 9611-92-2623
6a 6 Washer Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2131 9611-92-2624
7 1 Shaft Service kit, FPM . . . . . . . . . . . . . . . . . ۫ 9611-92-2132 9611-92-2625
8 1 Connex pin
Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2133 9611-92-2626
10 1 Drive ring
16 1 Adaptor
17 4 Screw for adaptor Service kit for flushed shaft seal
20 2 Nut Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2093 9611-92-2628
21 2 Washer Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2094 9611-92-2629
22 1 Safety guard Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2095 9611-92-2630
23 1 Screw for safety guard
24 6 Cap nut
24a 6 Washer Service kit for flushed shaft seal and impeller screw
25 1 Back plate
Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2134 9611-92-2631
26 ۫{¨Ÿ 1 O-ring
az Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2135 9611-92-2632
27 1 Impeller Service kit, FPM . . . . . . . . . . . . . . . . . 9611-92-2136 9611-92-2633
28 6 Bolt Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2137 9611-92-2634
29 1 Pump casing
30b 1 Support bar, left Service kit for double mechanical shaft seal
31 4 Leg
32 4 Screw
33 4 Nut Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2231 a 9611-92-2636
34 4 Spring washer Service kit, FPM. . . . . . . . . . . . . . . . . . ¨ 9611-92-2232 a 9611-92-2637
35 4 Screw Service kit, FEP . . . . . . . . . . . . . . . . . . ¨ 9611-92-2233 a 9611-92-2638
35a 4 Washer
36 1 Impeller screw
37 1 Impeller for impeller screw Service kit for double mechanical shaft seal and impeller screw
38 ۫Ÿz 1 O-ring
Service kit, EPDM (Std.) . . . . . . . . . Ÿ 9611-92-2234 z 9611-92-2639
40 1 Seal housing
40a 1 Seal housing
42 2 Tube Service kit, FEP . . . . . . . . . . . . . . . . . . Ÿ 9611-92-2237 z 9611-92-2642
46 4 Distance
57 1 Inducer
Replace to inducer (for pump without impellerscrew) please order pos. 7+57+37+38.
900017/5
53
DM
S S
FSS
Alternatives
54

1 1 Motor
1 Motor Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2088 9611-92-2619
1 Edge list Service kit, FPM. . . . . . . . . . . . . . . . . . 9611-92-2090 9611-92-2621
2 1 Shroud
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2091 9611-92-2622
1 Shroud
3 4 Screw
5a 1 Compression ring with thread Service kit for single shaft seal and impeller screw
6 6 Screw Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2130 9611-92-2623
6a 6 Washer Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2131 9611-92-2624
7 1 Shaft Service kit, FPM . . . . . . . . . . . . . . . . . ۫ 9611-92-2132 9611-92-2625
8 1 Connex pin
Service kit, FEP . . . . . . . . . . . . . . . . . ۫ 9611-92-2133 9611-92-2626
10 1 Drive ring
16 1 Adaptor
17 4 Screw for adaptor Service kit for flushed shaft seal
20 2 Nut Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2093 9611-92-2628
21 2 Washer Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2094 9611-92-2629
22 1 Safety guard Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2095 9611-92-2630
24 6 Cap nut
24a 6 Spring washer Service kit for flushed shaft seal and impeller screw
25 1 Back plate Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2134 9611-92-2631
26 ۫{¨Ÿ 1 O-ring Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2135 9611-92-2632
az
27 1 Impeller Service kit, FPM . . . . . . . . . . . . . . . . . 9611-92-2136 9611-92-2633
28 6 Bolt Service kit, FEP . . . . . . . . . . . . . . . . . 9611-92-2137 9611-92-2634
29 1 Pump casing
30b 1 Support bar, left Service kit for double mechanical shaft seal
31 4 Leg Service kit, EPDM (Std.) . . . . . . . . . ¨ 9611-92-2230 a 9611-92-2635
32 4 Screw
Service kit, NBR . . . . . . . . . . . . . . . . . ¨ 9611-92-2231 a 9611-92-2636
33 4 Nut
34 4 Spring washer Service kit, FPM. . . . . . . . . . . . . . . . . . ¨ 9611-92-2232 a 9611-92-2637
35 4 Screw Service kit, FEP . . . . . . . . . . . . . . . . . . ¨ 9611-92-2233 a 9611-92-2638
35a 4 Washer Service kits
36 1 Impeller screw
38 ۫Ÿz 1 O-ring Service kit for double mechanical shaft seal and impeller screw
42 2 Tube
53 4 Pivot screw (30 kW only) Service kit, FEP . . . . . . . . . . . . . . . . . . Ÿ 9611-92-2237 z 9611-92-2642

900018/7
55
7.14 LKH 5-60 Centrifugal Pumps, Shaft Seals
Single Shaft Seal.
13
15
14
TD 200-372_1
12
11
Flushed Shaft Seal.
43
44
45
13
15
14 TD 200-373_1
12
11
Double Mechanical Shaft Seal
50
51
44
52
14
15
13
15
14 TD 200-374
12
11
56
Parts list
Complete shaft seal
۫ Complete shaft seal
{ Complete shaft seal
Complete shaft seal
Ÿa Complete shaft seal
¨z Complete shaft seal
11 1 Stationary seal ring
12 1 O-ring
13 1 Spring
14 1 Rotating seal ring
2 Rotating seal ring, carbon
15 1 O-ring
2 O-ring
43 1 Lip seal
44 1 O-ring for seal housing
45 1 O-ring for drive ring
50 1 O-ring
51 1 Sec. stationary seal ring
52 1 Drive ring
57
DM
SS
FSS
Legs for motor sizes 55-75 kW
58

1 1 Motor
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2241 9611-92-2646
6 6 Screw
6a 6 Washer Service kit for flushed shaft seal
7 1 Shaft
10 1 Drive ring Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2242 9611-92-2647
16 1 Adaptor Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2243 9611-92-2648
17 4 Screw for adaptor Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2244 9611-92-2649
Service kit, FEP . . . . . . . . . . . . . . . . . . ۫ 9611-92-2245 9611-92-2650
20 4 Nut
21 4 Washer Service kit for double mechanical shaft seal
22 1 Safety guard
23 1 Screw for safety guard Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2416 9611-92-2651
24 8 Cap nut Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2417 9611-92-2652
24a 8 Spring washer Service kit, FPM. . . . . . . . . . . . . . . . . . 9611-92-2418 9611-92-2653
25 1 Back plate Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2419 9611-92-2654
26 ۫ 1 O-ring
28 8 Pin bolt
29 1 Pump casing
31 4 Leg
32 4 Screw
33 4 Nut
34 4 Spring washer
35 4 Screw
35a 4 Washer
36 1 Impeller screw
37 1 Impeller
38 ۫ 1 O-ring
40 1 Seal housing
40a 1 Seal housing
42 2 Tube
47 2 Leg bracket
48 4 Nut for leg
49 4 Screw for leg
53 4 Pivot screw

Conversion kit, single to flushed shaft seal EPDM C/SIC 9611-92-2246 = Pos 40+41+42+43+44+45
Conversion kit, single to double mechanical shaft seal EPDM C/SIC 9611-92-2420 = Pos.13+14+15+ 40a+41+42+44+50+51+52+54
Conversion kit, flushed to double mechanical shaft seal EPDM C/SIC 9611-92-2421 = Pos.13+14+15+ 40a+41+50+51+52+54
900058/8
59
6a
6
70
TD 239-013
60

1 1 Motor
5a 1 Compression ring with thread Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2976 9611-92-2985
5b 1 Compression ring without thread Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2977 9611-92-2986
6a 6 Washer
7 1 Shaft with pin
10 1 Drive ring Service kit for flushed shaft seal
16 1 Adaptor
Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2979 ¨ 9611-92-2988
19 4 Washer for adaptor Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2980 ¨ 9611-92-2989
20 4 Nut Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2981 ¨ 9611-92-2990
21 4 Washer
22 1 Safety guard
23 1 Screw for safety guard Service kit for double mechanical shaft seal
24 8 Wing nut Service kit, EPDM (Std.) . . . . . . . . . { 9611-92-2982 Ÿ 9611-92-2991
24a 8 Spring washer Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2983 Ÿ 9611-92-2992
25 1 Back plate Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2984 Ÿ 9611-92-2993
26 ۫{¨Ÿ 1 O-ring
28 8 Pin bolt
29 1 Pump casing
36 1 Impeller screw
37 1 Impeller
38 ۫{¨Ÿ 1 O-ring
40 1 Seal housing
40a 1 Seal housing
42 2 Tube
70 1 Bracket set stainless steel

900511/0
61
DM
SS
FSS
62

1 1 Motor
2 1 Shroud Service kit, EPDM. . . . . . . . . . . . . . . . 9611-92-2843 9611-92-2855
5b 1 Compression ring without thread Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2846 9611-92-2858
6 6 Screw
6a 6 Washer Service kit for flushed shaft seal
7 1 Shaft
10 1 Drive ring Service kit, EPDM. . . . . . . . . . . . . . . . ۫ 9611-92-2847 9611-92-2859
16 1 Adaptor Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2848 9611-92-2860
17 4 Screw for adaptor Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2849 9611-92-2861
Service kit, FEP . . . . . . . . . . . . . . . . . . ۫ 9611-92-2850 9611-92-2862
20 4 Nut
21 4 Washer Service kit for double mechanical shaft seal
22 1 Safety guard
23 1 Screw for safety guard Service kit, EPDM. . . . . . . . . . . . . . . . 9611-92-2851 9611-92-2863
24 8 Cap nut Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2852 9611-92-2864
24a 8 Spring washer Service kit, FPM. . . . . . . . . . . . . . . . . . 9611-92-2853 9611-92-2865
25 1 Back plate Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2854 9611-92-2866
26 ۫ 1 O-ring
27 1 Impeller
28 8 Pin bolt
29 1 Pump casing
31 4 Leg
32 4 Screw
33 4 Nut
34 4 Spring washer
35 4 Screw
35a 4 Washer
36 1 Impeller screw
37 1 Impeller
38 ۫ 1 O-ring
40 1 Seal housing
42 2 Tube
47 2 Leg bracket
48 4 Nut for leg
49 4 Screw for leg
53 4 Pivot screw
900058/8
63
DM
SS
FSS
64

1 1 Motor
2 1 Shroud Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2953 9611-92-2965
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2955 9611-92-2967
6 6 Screw (30 - 75 kW)
8 Screw (90 - 110 kW) Service kit for flushed shaft seal
6a 6 Washer (30 - 75 kW)
Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2956 9611-92-2968
8 Washer (90 - 110 kW)
7 1 Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2957 9611-92-2969
Shaft with pin
10 1 Drive ring Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2958 9611-92-2970
16 1 Adaptor Service kit, FEP . . . . . . . . . . . . . . . . . . ۫ 9611-92-2959 9611-92-2971

Service kit for double mechanical shaft seal
21 4 Washer Service kit, NBR . . . . . . . . . . . . . . . . . { 9611-92-2961 9611-92-2973
22 1 Safety guard
Service kit, FPM. . . . . . . . . . . . . . . . . . { 9611-92-2962 9611-92-2974
Service kit, FEP . . . . . . . . . . . . . . . . . . { 9611-92-2963 9611-92-2975
24 16 Cap nut
24a 16 Spring washer
25 1 Back plate
26 ۫{ 2 O-ring
28 16 Pin bolt
29a 1 Pump casing
31 4 Leg
32 4 Screw
33 4 Nut
34 4 Spring washer
35 4 Screw
35a 4 Washer
36 1 Impeller screw
37 1 Impeller
38 ۫{ 1 O-ring
40 1 Seal housing
42 2 Fitting
47 2 Leg bracket
48 4 Nut for leg
49 4 Screw for leg
53 4 Pivot screw
900410/0
65
DM
SS
FSS
66

1 1 Motor
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2870 9611-92-2882
6 6 Screw (30 - 45 kW)
8 Screw (55-75 kW) Service kit for flushed shaft seal
6a 6 Washer (30 - 45 kW)
Service kit, EPDM (Std.) . . . . . . . . . ۫ 9611-92-2871 9611-92-2883
8 Washer (55-75 kW)
7 1 Service kit, NBR . . . . . . . . . . . . . . . . . ۫ 9611-92-2872 9611-92-2884
Shaft with pin
10 1 Drive ring Service kit, FPM. . . . . . . . . . . . . . . . . . ۫ 9611-92-2873 9611-92-2885
16 1 Adaptor Service kit, FEP . . . . . . . . . . . . . . . . . . ۫ 9611-92-2874 9611-92-2886

Service kit for double mechanical shaft seal
20 4 Nut Service kit, EPDM (Std.) . . . . . . . . . 9611-92-2875 9611-92-2887
21 4 Washer Service kit, NBR . . . . . . . . . . . . . . . . . 9611-92-2876 9611-92-2888
22 1 Safety guard
Service kit, FPM. . . . . . . . . . . . . . . . . . 9611-92-2877 9611-92-2889
Service kit, FEP . . . . . . . . . . . . . . . . . . 9611-92-2878 9611-92-2890
24 16 Cap nut
24a 16 Spring washer
25 1 Back plate
26 ۫ 2 O-ring
28 16 Pin bolt
29 1 Pump casing
29a 1 Pump cover
31 4 Leg
32 4 Screw
33 4 Nut
34 4 Spring washer
35 4 Screw
35a 4 Washer
36 1 Impeller screw
37 1 Impeller
38 ۫ 1 O-ring
40 1 Seal housing
40a 1 Seal housing
42 2 Tube
47 2 Leg bracket
48 4 Nut for leg
49 4 Screw for leg
53 4 Pivot screw

900268/5
67
7.20 LKH-70, LKH-75, LKH-80, LKH-85 and LKH-90 Centrifugal Pump, Shaft Seal
Single Shaft Seal
13
15
14
12
TD 239-002_1
11
Flushed Shaft Seal
TD 239-003_2
Double Mechanical Shaft Seal
TD 239-004_2
68
Parts list
Complete shaft seal
Complete shaft seal
۫ Complete shaft seal
Complete shaft seal
{ Complete shaft seal
Complete shaft seal
11 1 Stationary seal ring, SiC.
12 1 O-ring
13 1 Spring
14 1 Rotating seal ring
2 Rotating seal ring
15 1 O-ring
2 O-ring
43 1 Lip seal
44 1 O-ring for seal housing
45 1 O-ring for drive ring
50 1 O-ring
51 1 Sec. stationary seal ring, SiC.
52 1 Drive ring
54 2 Cup
69
How to contact Alfa Laval
Contact details for all countries are
continually updated on our website.
Please visit www.alfalaval.com to access the information direct.

Instruction Manual: LKH Centrifugal Pump

Uploaded by

Copyright:

Available Formats

Instruction Manual: LKH Centrifugal Pump

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Instruction Manual: LKH Centrifugal Pump

Uploaded by

Copyright:

Available Formats

Instruction Manual

LKH Centrifugal Pump

1. EC Declaration of Conformity ....................................................................... 5

6. Technical data ......................................................................................... 30

7. Parts list and Service Kits ........................................................................... 33

The designated company

Albuen 31, DK-6000 Kolding, Denmark

hereby declare that

is in conformity with the following directives with amendments:

The technical construction file is retained at the above address

Manager, Product Center Fluid Handling Bjarne Søndergaard

Alfa Laval Kolding

2.1 Important information

2.2 Warning signs

Dangerous electrical voltage:

2.3 Safety precautions

Pump without impeller screw:

Pump with Impeller screw:

Motors with grease nipples:

Step 1 Check the delivery for:

Step 4 Remove the shroud before lifting!

Always have the pump electrically connected by

S tep 4 Remember seal rings!

3.3 Pre-use check - Pump without/with impeller screw

Always remove the impeller before checking the direction of

S tep 2 See the indication label!

Step 1 See the indication label!

Always read the technical data thoroughly.

Step 2 Burning danger!

Step 3 Explosion danger!

S tep 4 Do not run dry! See the warning

For LKH-85: connect inlet/outlet of the flushing liquid directly

4.2 Fault finding

Problem Cause/result Remedy

Overloaded motor - Pumping of viscous liquids - Larger motor or smaller impeller

Leaking shaft seal - Dry run (See 4.1 Operation/Control) Replace:

4.3 Recommended cleaning

Step 1 Caustic danger!

Always handle lye and acid with great care.

Always use rubber gloves! Always use protective

Step 2 Burning danger!

Never touch the pump or the pipelines when sterilizing.

Examples of cleaning agents: Use clean water, free from

2.2 l (0.6 gal) + 100 l (26.4 gal) = Cleaning agent.

2. 0.5% by weight HNO3 at 70°C (158°F).

Step 5 Always rinse!

5.1 General maintenance

Always read the technical data thoroughly.

Always disconnect the power supply when servicing the pump.

Step 2 Burning danger!

Never service the pump when it is hot.

Step 3 Atmospherie pressure

Ordering spare parts

Shaft seal Rubber seals Motor bearings

Preventive maintenance R eplace after 12 months: Replace when replacing the

Lubrication Before fitting Before fitting See section 6.2 Relubrication

5.2 Dismantling of pump/shaft seals

LKH-85 and LKH-90

Step 6 Use the tool

Voltage and frequency (standard) 3~, 50 Hz, 220-240V¨/380-420VY 4 kW

Parts marked with ۫{¨Ÿaz are included in the service kits.

Parts marked with ۫{¨Ÿaz are included in the service kits.

Parts marked with ۫{¨Ÿaz are included in the service kits.

Parts marked with ۫{¨Ÿaz are included in the service kits.

Parts marked with ۫{¨Ÿaz are included in the service kits.

Parts marked with ۫{¨Ÿaz are included in the service kits.

Parts marked with ۫{¨Ÿaz are included in the service kits.