General Body Repairs, Exterior PDF

Service
Workshop Manual
Audi A6 2011 ➤
Audi A6 China 2012 ➤
General body repairs, exterior
Edition 10.2019
Service Department. Technical Information

Service
List of Workshop Manual Repair Groups
Repair Group
00 - Technical data
50 - Body - front
55 - Bonnet, rear lid
57 - Front doors, door components, central locking
58 - Rear doors, door components
60 - Sunroof
63 - Bumpers
64 - Glazing
66 - Exterior equipment
Technical information should always be available to the foremen and mechanics, because their
careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and
safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a
matter of course, be observed.
All rights reserved.

No reproduction without prior agreement from publisher.
Copyright © 2019 Audi AG, Ingolstadt D3E80352453

Audi A6 2011 ➤ , Audi A6 China 2012 ➤
General body repairs, exterior - Edition 10.2019
Contents
00 - Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Safety precautions when working on the high-voltage system . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Safety precautions when working in the vicinity of high-voltage components . . . . . . . . . . 2
1.3 Safety precautions when working on vehicles with start/stop system . . . . . . . . . . . . . . . . 2
1.4 Safety precautions when using testers and measuring instruments during a road test . . . . 2
1.5 Safety precautions when working on the cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Repair notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Routing and attachment of lines and wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Contact corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Bonding surfaces for adhesive strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Self-locking bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
50 - Body - front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Lock carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Exploded view - lock carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Removing and installing lock carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Wing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1 Exploded view - wing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 Removing and installing wing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 Bulkhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1 Exploded view - plenum chamber partition panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Exploded view - plenum chamber cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3 Removing and installing plenum chamber partition panel . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 Removing and installing plenum chamber cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
55 - Bonnet, rear lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1 Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.1 Exploded view - bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.2 Exploded view - Bowden cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.3 Removing and installing bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.4 Adjusting bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.5 Removing and installing hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.6 Removing and installing striker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.7 Removing and installing gas strut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.8 Releasing gas from gas strut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1.9 Removing and installing insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1.10 Removing and installing Bowden cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1.11 Removing and installing bonnet lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
1.12 Removing and installing operating lever for bonnet lock . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2 Rear lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.1 Exploded view - rear lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.2 Removing and installing rear lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2.3 Adjusting rear lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
2.4 Removing and installing hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2.5 Removing and installing rear lid seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.6 Removing and installing gas strut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
2.7 Releasing gas from gas strut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.9 Removing and installing actuating mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2.10 Removing and installing rear lid power opening control unit J938 . . . . . . . . . . . . . . . . . . 74
2.11 Removing and installing rear lid power opening sender G750 / G760 . . . . . . . . . . . . . . . . 75
Contents i
2.12 Removing and installing rear lid lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

2.13 Removing and installing extension spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3 Tank flap unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
3.1 Exploded view - tank flap unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
3.2 Removing and installing tank flap unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
4 Charging flap unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4.1 Exploded view - charging flap unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4.2 Removing and installing charging flap unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4.3 Removing and installing charging flap unit trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
4.4 Removing and installing manual release cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
57 - Front doors, door components, central locking . . . . . . . . . . . . . . . . . . . . . . . . . . 92

1 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
1.1 Exploded view - door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
1.2 Exploded view - door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
1.3 Removing and installing door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
1.4 Adjusting door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
1.5 Adjusting striker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
1.6 Removing and installing door arrester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
1.7 Removing and installing inner door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
1.8 Removing and installing outer door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
2 Door components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
2.1 Exploded view - window regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
2.2 Exploded view - door handle and door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
2.3 Exploded view - window guides and window slot trim strips . . . . . . . . . . . . . . . . . . . . . . . . 116
2.4 Removing and installing window regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
2.5 Removing and installing window regulator motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
2.6 Removing and installing door handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
2.7 Removing and installing mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
2.8 Removing and installing door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
2.10 Removing and installing inner door cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
2.11 Removing and installing power latching motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
2.12 Removing and installing window guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
2.13 Removing and installing outer window slot trim strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
3 Central locking system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
3.1 Overview of fitting locations - central locking system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
3.2 Removing and installing driver door control unit J386 and front passenger door control unit
J387 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
3.3 Removing and installing rear left door control unit J388 and rear right door control unit J389
...................................................................... 137
3.4 Removing and installing convenience system central control unit J393 . . . . . . . . . . . . . . 137
3.5 Removing and installing interface control unit for vehicle location system J843 . . . . . . . . 141
3.6 Removing and installing bonnet contact switch F266 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
3.7 Removing and installing tank filler flap locking motor V155 . . . . . . . . . . . . . . . . . . . . . . . . 141
3.8 Removing and installing actuator for high-voltage charging flap lock 1 F496 . . . . . . . . . . 142
58 - Rear doors, door components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

1 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
1.1 Exploded view - door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
1.2 Exploded view - door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
1.3 Removing and installing door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
1.4 Adjusting door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
1.5 Adjusting striker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
1.6 Removing and installing door arrester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
1.7 Removing and installing inner door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
ii Contents
1.8 Removing and installing outer door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

2 Door components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
2.1 Exploded view - window regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
2.2 Exploded view - door handle and door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
2.3 Exploded view - window guides and window slot trim strips . . . . . . . . . . . . . . . . . . . . . . . . 168
2.4 Removing and installing window regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
2.5 Removing and installing window regulator motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
2.6 Removing and installing door handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
2.7 Removing and installing mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
2.8 Removing and installing door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
2.10 Removing and installing inner door cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
2.11 Removing and installing power latching motor V329 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
2.12 Removing and installing window guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
2.13 Removing and installing window slot trim strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
60 - Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1 Sliding sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1.1 Exploded view - sliding sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1.2 Exploded view - sunroof sun blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
1.3 Removing and installing sliding sunroof frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
1.4 Removing and installing sliding sunroof panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
1.5 Adjusting sliding sunroof panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
1.6 Removing and installing glass panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
1.7 Checking and adjusting zero position for guide rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
1.8 Removing and installing sliding sunroof adjustment control unit J245 . . . . . . . . . . . . . . . . 198
1.9 Adapting sliding sunroof adjustment control unit J245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
1.10 Removing and installing sliding sunroof seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
1.11 Removing and installing sliding sunroof sun blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
1.12 Removing and installing cables for sunroof sun blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
1.13 Removing and installing sun blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
1.14 Removing and installing wind deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
2 Water drain hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
2.1 Overview - water drain hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
2.2 Cleaning water drain hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
2.3 Removing and installing water drain hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
63 - Bumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1 Bumper (front) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1.1 Exploded view - bumper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1.2 Exploded view - impact bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
1.3 Removing and installing bumper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
1.4 Removing and installing impact bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
1.5 Removing and installing attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
2 Bumper (rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
2.1 Exploded view - bumper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
2.2 Exploded view - impact bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
2.3 Removing and installing bumper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
2.4 Removing and installing impact bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
2.5 Removing and installing cable mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
2.6 Removing and installing attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
64 - Glazing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
1 Repair notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
1.1 Minimum drying times for bonded windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
Contents iii
1.2 Repairing windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

1.3 Notes on installing flush-bonded windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
1.4 Preparing undamaged windows for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
1.5 Preparing new windows for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
1.6 Preparing body flange for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
1.7 Cleaning off adhesive sealant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
1.8 Re-sealing windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
2 Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
2.1 Exploded view - windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
2.2 Removing and installing windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
3 Rear window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
3.1 Exploded view - rear window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
3.2 Removing and installing rear window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
4 Side windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
4.1 Exploded view - rear side window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
4.2 Removing and installing rear side window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
5 Door windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
5.1 Exploded view - front door window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
5.2 Exploded view - rear door window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
5.3 Removing and installing front door window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
5.4 Removing and installing rear door window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
66 - Exterior equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319

1 Radiator grille/front trim panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
1.1 Exploded view - radiator grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
1.2 Removing and installing radiator grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
2 Spoilers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
2.1 Exploded view - spoiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
2.2 Removing and installing spoiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
3 Strips / trim panels / extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
3.1 Exploded view - trim strip and covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
3.2 Exploded view - sill panel trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
3.3 Exploded view - side member trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
3.4 Exploded view - trim panel for B-pillar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
3.5 Exploded view - trim panel for C-pillar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
3.6 Exploded view - wheel arch covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
3.7 Exploded view - heat shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
3.8 Removing and installing trim strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
3.9 Removing and installing sill panel trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
3.10 Removing and installing cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
3.11 Removing and installing side member trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
3.12 Removing and installing water deflector strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
3.13 Removing and installing trim panel for B-pillar on door . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
3.14 Removing and installing trim panel for C-pillar on door . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
3.15 Removing and installing wheel arch covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
3.16 Removing and installing heat shield for floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
4 Noise insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
4.1 Exploded view - noise insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
4.2 Removing and installing noise insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
5 Underbody trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
5.1 Exploded view - underbody trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
5.2 Exploded view - underbody struts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
5.3 Removing and installing underbody trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
5.4 Removing and installing tunnel cross-piece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
iv Contents
5.5 Removing and installing diagonal struts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391

6 Decorative film / protective film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
6.1 Exploded view - protective film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
6.2 Renewing protective film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
7 Roof strips / roof rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
7.1 Exploded view - roof rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
7.2 Removing and installing roof rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
8 Exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
8.1 Exploded view - exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
8.2 Removing and installing exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
8.3 Removing and installing mirror glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
8.4 Removing and installing mirror adjustment unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
8.5 Removing and installing cover for mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
9 Wheel housing liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
9.1 Exploded view - wheel housing liner (front) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
9.2 Exploded view - wheel housing liner (rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
9.3 Removing and installing wheel housing liner (front) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
9.4 Removing and installing wheel housing liner (rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
10 Model badges and brand emblems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
10.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
10.2 Dimensions - model badges and brand emblems on rear . . . . . . . . . . . . . . . . . . . . . . . . . . 412
10.3 Dimensions - model badges and brand emblems on side . . . . . . . . . . . . . . . . . . . . . . . . . . 416
10.4 Removing and installing front emblem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
10.5 Removing and installing emblems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
11 Towing bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
11.1 Exploded view - towing bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
11.2 Removing and installing cable mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
11.3 Removing and installing retainer for cable mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . 422
11.4 Removing and installing towing bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
Contents v
vi Contents
00 – Technical data
1 Safety precautions
(ARL006670; Edition 10.2019)
⇒ “1.1 Safety precautions when working on the high-voltage sys‐
tem”, page 1
⇒ “1.2 Safety precautions when working in the vicinity of high-
voltage components”, page 2
⇒ “1.3 Safety precautions when working on vehicles with start/
stop system”, page 2
⇒ “1.4 Safety precautions when using testers and measuring in‐
struments during a road test”, page 2
⇒ “1.5 Safety precautions when working on the cooling system”,
page 2
1.1 Safety precautions when working on the high-voltage system

High voltage can cause fatal injury.
Voltage levels in the high-voltage system constitute a safety haz‐
ard; there is a danger of severe or fatal injuries from electric
shock.
– Persons with life-sustaining or other electronic medical devi‐
ces in or on their body must not perform any work on the high-
voltage system. Such medical devices include internal anal‐
gesic pumps, implanted defibrillators, pacemakers, insulin
pumps and hearing aids.
– The high-voltage system must be de-energised by a suitably
qualified person.
Risk of injury - engine may start unexpectedly

It is difficult to tell when an electric or hybrid vehicle's drive system
is active. If it is active, there is a risk of parts of the body and/or
clothing being trapped or drawn in.
– Switch off ignition.
– Deposit the ignition key outside of the vehicle.
Risk of damage to high-voltage wiring

Incorrect handling may result in damage to the insulation of high-
voltage wires or high-voltage connectors.
– Never use high-voltage wiring or high-voltage connectors as
a support.
– Never support tools or equipment on high-voltage wires and
high-voltage connectors.
– High-voltage cables must not be excessively bent or kinked.
– Pay attention to coding when connecting high-voltage con‐
nections.
1. Safety precautions 1
1.2 Safety precautions when working in the vicinity of high-voltage components

High voltage can cause fatal injury.
Voltage levels in the high-voltage system constitute a safety haz‐
ard; if high-voltage components or cables are damaged there is
a danger of severe or fatal injuries from electric shock.
– Carry out a visual check of high-voltage components and high-
voltage wiring.
– Never use cutting/forming tools or other sharp-edged imple‐
ments.
– Never perform work using welding, brazing, thermal bonding
or hot air.
1.3 Safety precautions when working on vehicles with start/stop system

Risk of injury - engine may start unexpectedly
The engine can start unexpectedly if the vehicle's start/stop sys‐
tem is activated. A message in the instrument cluster indicates
whether the start/stop system is activated.
– To deactivate the start/stop system, switch off the ignition.
1.4 Safety precautions when using testers and measuring instruments during
a road test
Risk of injury if test equipment is not secured
If an accident occurs and the front passenger's airbag is triggered,
test equipment which is not secured adequately may be catapul‐
ted through the vehicle with potentially serious consequences.
– Secure test equipment on the rear seat with a strap.
Or:
– Have a second mechanic operate test equipment on the rear
seat.
1.5 Safety precautions when working on the cooling system

Risk of scalding as hot coolant can escape
The cooling system is under pressure when the engine is hot. Risk
of scalding due to hot steam and hot coolant.
– Put on protective gloves.
– Put on safety goggles.
– Cover filler cap on expansion tank with a cloth and open care‐
fully to release pressure.
2 Rep. gr.00 - Technical data

1. Safety precautions 3
2 Repair notes
⇒ “2.1 Routing and attachment of lines and wiring”, page 4
⇒ “2.2 Contact corrosion”, page 4
⇒ “2.3 Bonding surfaces for adhesive strips ”, page 4
⇒ “2.4 Self-locking bolts”, page 4
2.1 Routing and attachment of lines and wir‐

ing
Make sketches or take photographs when unfastening or remov‐
ing and installing hydraulic and pneumatic lines or electrical wires.
This ensures that you can re-install them at the original location.
2.2 Contact corrosion

Contact corrosion can occur if unsuitable fasteners are used (e.g.
bolts, nuts, washers, etc.).
For this reason, only fasteners with a special surface coating are
fitted.
Additionally, all rubber and plastic parts and all adhesives are
made of non-conductive materials.
Always install new parts as listed in the Electronic parts catalogue
if you are not sure whether used parts can be refitted.
Please note:
♦ We recommend using only genuine replacement parts: these
have been fully tested and are compatible with aluminium.
♦ We recommend using Audi Genuine Accessories.
♦ Damage caused by contact corrosion is not covered by the
warranty.
2.3 Bonding surfaces for adhesive strips

♦ The vehicle must be at room temperature before fitting e.g.
self-adhesive covers or door seals etc. with adhesive strips.
♦ Bonding surfaces on the body must be free of dust and grease.
♦ Clean bonding surfaces with cleaning solution - D 009 401
04- .
♦ Apply primer - D 355 205 A2- to bonding surfaces on body
using applicator - D 009 500 25- and allow to flash off.
♦ Heat bonding surfaces with a hot air blower to approx. 40℃.
♦ After installation, press covers attached with adhesive strips
on again using a roller.
♦ Subsequently, check that components are attached securely
by pulling them with your hand.
2.4 Self-locking bolts

If bolts secured with microencapsulation have been removed,
they must be renewed, and the threaded holes must be cleaned
with a suitable tap.
4 Rep. gr.00 - Technical data

50 – Body - front
1 Lock carrier
⇒ “1.1 Exploded view - lock carrier”, page 5
⇒ “1.2 Removing and installing lock carrier”, page 7
1.1 Exploded view - lock carrier

⇒ “1.1.1 Exploded view - lock carrier, vehicles up to model year
2014”, page 5
⇒ “1.1.2 Exploded view - lock carrier, vehicles from model year
2015 onwards”, page 6
1.1.1 Exploded view - lock carrier, vehicles up to model year 2014
1 - Bolt
❑ 8 Nm
2 - Speed nut
3 - Lock carrier
❑ For correct version refer
to ⇒ Electronic parts
catalogue
❑ Removing and installing
⇒ page 7
4 - Bolt
❑ 20 Nm
5 - Bolt
❑ 20 Nm
6 - Brace
❑ For lock carrier
❑ For correct version refer
to ⇒ Electronic parts
catalogue
⇒ page 10
7 - Bolt
❑ 10 Nm
8 - Bolt
❑ 2x
❑ 8 Nm
9 - Rivet
❑ 2x
10 - Counterhold tool
❑ For mounting with ad‐
juster element
❑ Removing and installing ⇒ page 11
11 - Mounting for impact bar
❑ Exploded view ⇒ page 225
1. Lock carrier 5
12 - Mounting
❑ With adjuster element
❑ For bumper cover (front), retainer for headlight housing
13 - Adjuster element
1.1.2 Exploded view - lock carrier, vehicles from model year 2015 onwards
2 - Mounting
❑ With adjuster element
❑ For bumper cover
(front), headlight hous‐
ing
⇒ page 10
3 - Speed nut
4 - Bolt
❑ 8 Nm
5 - Lock carrier
⇒ page 7
6 - Bolt
❑ 2x
❑ 8 Nm
7 - Bolt
❑ 10 Nm
8 - Rivet
❑ 2x
9 - Counterhold tool
❑ For mounting with ad‐
juster element
⇒ page 11
❑ Exploded view
⇒ page 225
6 Rep. gr.50 - Body - front

1.2 Removing and installing lock carrier

⇒ “1.2.1 Removing and installing lock carrier - Audi A6”,
page 7
⇒ “1.2.2 Removing and installing lock carrier - Audi S6/RS 6”,
page 8
⇒ “1.2.3 Removing and installing lock carrier brace”, page 10
⇒ “1.2.4 Removing and installing bumper cover mounting - vehi‐
cles up to model year 2014”, page 10
⇒ “1.2.5 Removing and installing bumper cover mounting - vehi‐
cles from model year 2015 onwards”, page 10
⇒ “1.2.6 Removing and installing retainer for bumper cover
mounting”, page 11
1.2.1 Removing and installing lock carrier -

Audi A6
Removing
– Remove noise insulation (front) ⇒ page 382 .
– Remove impact bar ⇒ page 232 .
– Remove radiator with radiator cowl ⇒ Rep. gr. 19 ; Radiator/
radiator fans; Removing and installing radiator .
– Remove bolt -4-.
– Unplug electrical connectors -1, 2-.
– Unplug electrical connector -3- at crash sensor for front airbag
(observe safety precautions ⇒ General body repairs, interior;
Rep. gr. 00 ; Safety precautions; Safety precautions when
working on pyrotechnic components ).
– If fitted, unplug electrical connector -4- for secondary air pump

motor - V101- .
– Press release tabs and disconnect secondary air hoses -1-
and -2-.
– Detach bonnet lock cable at coupling unit and move clear at
lock carrier ⇒ page 27 .
1. Lock carrier 7
– If fitted, unscrew bolt -5-.

– Have a second person hold lock carrier -4- in position, and
unscrew bolts -1 ... 3-.
– Detach lock carrier with mountings for impact bar with help of
second person.
To renew lock carrier, mounting for impact bar and, if fitted, brack‐
et for secondary air pump motor must be removed.
♦ Removing mounting for impact bar ⇒ page 234
♦ Removing bracket with secondary air pump motor ⇒ Rep. gr.
26 ; Secondary air system; Exploded view - secondary air sys‐
tem
Installing
Installation is carried out in reverse order; note the following:
– Install headlight housing ⇒ Electrical system; Rep. gr. 94 ;
Headlights; Removing and installing headlights .
– Align bumper cover mounting (front) -2-, hold in position and

tighten bolt -1-.
• Edge of headlight housing -4- must be flush with wing panel
-3- -arrow-.
Tightening torques
♦ ⇒ “1.1.1 Exploded view - lock carrier, vehicles up to model year
2014”, page 5
♦ ⇒ “1.2 Exploded view - impact bar”, page 225
1.2.2 Removing and installing lock carrier -

Audi S6/RS 6
Removing
– Remove radiator with radiator cowl ⇒ Rep. gr. 19 ; Radiator/
radiator fans; Removing and installing radiator .


– Detach bonnet lock cable at coupling unit and move clear at
lock carrier ⇒ page 27 .

– Have a second mechanic hold lock carrier -4- in position and
unscrew bolts -1 ... 3-.
Note
-Item 5- not installed.
– Detach lock carrier with mountings for impact bar with help of
second mechanic.
To renew lock carrier, mounting for impact bar must be removed.
♦ Removing mounting for impact bar ⇒ page 234
Installing
– Install headlight housing ⇒ Electrical system; Rep. gr. 94 ;
– Align bumper cover mounting (front) -2-, hold in position and

tighten bolt -1-.
• Edge of headlight housing -4- must be flush with wing panel
-3- -arrow-.
Tightening torques
2014”, page 5
1. Lock carrier 9
1.2.3 Removing and installing lock carrier

brace
Removing
– Unscrew bolts -arrows- and detach lock carrier brace (top)
-1-.
Installing
Installation is carried out in reverse sequence.
Tightening torques
2014”, page 5
1.2.4 Removing and installing bumper cover

mounting - vehicles up to model year
2014
Removing
– Remove bumper cover (front) ⇒ page 226 .
– Remove headlight housing ⇒ Electrical system; Rep. gr. 94 ;
– Audi S6/RS 6, left-side: Remove secondary air pump motor
with bracket ⇒ Rep. gr. 26 ; Secondary air system; Removing
and installing secondary air pump motor - V101- .
– Remove bolts -2, 3, 4-.
– Detach mounting -1-.
Installing
Tightening torques
2014”, page 5

mounting - vehicles from model year
2015 onwards
Removing

– Right-side: Remove air cleaner housing ⇒ Rep. gr. 23 ; Air

cleaner; Removing and installing air cleaner housing or ⇒
Rep. gr. 24 ; Air cleaner; Removing and installing air cleaner
housing .
– Unplug electrical connector -1- and move it clear.
– If fitted, unplug electrical connector for control unit for NOx
sender - J583- .

Installing
Tightening torques
♦ ⇒ “1.1.2 Exploded view - lock carrier, vehicles from model year
1.2.6 Removing and installing retainer for

bumper cover mounting
Special tools and workshop equipment required
♦ Drill
♦ Drill bit, ∅ 4 mm
Removing
1. Lock carrier 11
– Release retaining tabs -arrows A- and detach air duct -1-

-arrow B-.
– Audi RS 6: Remove water radiator for charge air cooling circuit
and tie up to one side with lines connected ⇒ Rep. gr. 19 ;
Radiators/radiator fans; Removing and installing water radia‐
tor for charge air cooling circuit .

– Drill out heads of pop rivets -arrows-, knock out rivet stems
and detach retainer -2-.
Installing
– Check installation position of bumper mounting and adjust if
necessary
⇒ “1.3.3 Adjusting bumper cover (front)”, page 230 .
Tightening torques
2014”, page 5

2 Wing
⇒ “2.1 Exploded view - wing”, page 13
⇒ “2.2 Removing and installing wing”, page 14
2.1 Exploded view - wing
1 - Bolt
❑ 2x
❑ 10 Nm
2 - Bracket (bottom)
❑ For wing
⇒ page 16
3 - Bolt
❑ 2x
❑ 10 Nm
4 - Sealing piece
5 - Bolt
❑ 4x
❑ 10 Nm
6 - Bolt
❑ 10 Nm
7 - Wing
❑ Different versions ⇒
Electronic parts cata‐
logue
⇒ page 14
8 - Bolt
❑ 2x
❑ 10 Nm
9 - Bolt
❑ 2x
❑ 10 Nm
10 - Closure plate
❑ Different versions ⇒ Electronic parts catalogue
11 - Spreader rivet
❑ 2x
2. Wing 13
2.2 Removing and installing wing

⇒ “2.2.1 Removing and installing wing”, page 14
⇒ “2.2.2 Removing and installing closure plate”, page 15
⇒ “2.2.3 Removing and installing wing bracket (bottom)”,
page 16
2.2.1 Removing and installing wing

Removing
– Remove closure plate ⇒ page 15 .
– Remove bumper cover mounting (front) ⇒ page 245 .
– Remove bolts -2 ... 5-.

– Detach wing panel -1-.
Installing

– Sealing piece -2- must be positioned between wing mounting

flange and wing panel -1- as shown in illustration.
Tightening torques
♦ ⇒ “2.1 Exploded view - wing”, page 13
2.2.2 Removing and installing closure plate

Removing
– Remove front wheel housing liner ⇒ page 406 .
– Left-side: Remove washer fluid reservoir ⇒ Electrical system;
Rep. gr. 92 ; Windscreen washer system; Removing and in‐
stalling washer fluid reservoir .
– Right-side: Release fastener -3- (if fitted).
– Pull out bracket -1- in direction of -arrow A-, disengage down‐
wards -arrow B- and remove.
– Unplug electrical connector -2- at power unit mounting control
unit.
– Remove spreader rivets -4-.

– Detach guide -3- on closure plate (top) on wing panel -2-.
– Pull out closure plate -1- towards front starting at bottom.
Installing
2. Wing 15
– Guide -1- on closure plate (top) -2- must be slid onto wing
panel -3-.
Tightening torques
2.2.3 Removing and installing wing bracket

(bottom)
Removing
– Remove wing panel ⇒ page 14 .
– Left-side: Move wiring harness and headlight washer fluid line
clear -arrows-.
– Right side: Move wiring harness clear.
– Remove bolts -2, 3-.
– Detach bracket (bottom) -1-.
Installing
Tightening torques

3 Bulkhead
⇒ “3.1 Exploded view - plenum chamber partition panel”,
page 17
⇒ “3.2 Exploded view - plenum chamber cover”, page 18
⇒ “3.3 Removing and installing plenum chamber partition panel”,
page 18
⇒ “3.4 Removing and installing plenum chamber cover”,
page 21
3.1 Exploded view - plenum chamber partition panel
1 - Seal
❑ Slide onto plenum
chamber partition panel
2 - Clamping washer
❑ 2x
3 - Nut
❑ 4 Nm
4 - Plenum chamber partition
panel
logue
⇒ page 18
5 - Terminal 30 wiring junction
- TV2-
⇒ Electrical system;
Rep. gr. 97 ; Relay car‐
riers, fuse carriers, elec‐
tronics boxes; Overview
of fitting locations - relay
carriers, fuse carriers,
electronics boxes
6 - Nut
❑ Tightening torque ⇒
Electrical system; Rep.
gr. 97 ; Relay carriers,
fuse carriers, electron‐
ics boxes; Overview of
fitting locations - relay
carriers, fuse carriers,
electronics boxes
7 - Cable tie clip
8 - Bolt
❑ 2 Nm
9 - Heat shield
3. Bulkhead 17
3.2 Exploded view - plenum chamber cover
1 - Seal
❑ Renew if damaged
2 - Plenum chamber cover
⇒ page 21
3 - Foam wedge (right-side)
4 - Retaining clip
5 - Mounting (right-side)
❑ For clip
6 - Cowl panel trim
⇒ page 22
7 - Mounting (left-side)
❑ For clip
8 - Retaining clip
9 - Foam wedge (left-side)
10 - Cover
❑ For brake fluid reservoir
3.3 Removing and installing plenum cham‐

ber partition panel
♦ Hose clamps up to 25 mm - 3094-

Removing
– Remove body brace ⇒ Running gear, axles, steering; Rep.
gr. 40 ; Suspension strut, upper links; Removing and installing
body brace .
– Release retainer -arrow A- and open cover -arrow B-.
– Remove nut -3- and move electrical wiring clear.

– Take electrical connector -1- out of bracket.
– Unscrew nuts -arrows- and detach terminal 30 wiring junc‐
tion 2 - TV22- from plenum chamber partition panel.
– Move electrical wiring harness clear at plenum chamber par‐
tition panel.
Vehicles with petrol engine:

– Cover area underneath cut-off valve with absorbent cloth or
absorbent paper.
– Clamp off coolant hoses -1 and 3- with hose clamps -3094- .
– Unfasten hose clips and disconnect coolant hose -2- from
shut-off valve.
– Press grommet -4- out of plenum chamber partition panel to‐
wards engine.
Note
The illustration shows a vehicle with auxiliary heater.
3. Bulkhead 19
All vehicles (continued):

– If fitted, detach heat shield -1- upwards -arrow-.
– Release fasteners -arrows A- and detach leadthrough -1- up‐

wards -arrow B-.
– Remove bolt -arrow-.
Note
Different securing methods may have been used: cable tie clip,
clip or bolt.
– Disconnect vacuum line -3- for brake servo.

– Pull off grommet -1- for vacuum connection.
– Unscrew nut -2- and lift off plenum chamber partition panel
-4-.
Installing
• Tightening torque ⇒ page 17

– Make sure that seal -2- for plenum chamber partition panel
-1- is seated correctly in mounting -3- of plenum chamber.
– Check coolant level ⇒ Rep. gr. 19 ; Cooling system/coolant;
Draining and filling cooling system .
3.4 Removing and installing plenum cham‐

ber cover
⇒ “3.4.1 Removing and installing plenum chamber cover”,
page 21
⇒ “3.4.2 Removing and installing cowl panel trim”, page 22
3.4.1 Removing and installing plenum cham‐

ber cover
Removing
– Pull off seal -7-.
– Lift plenum chamber cover -3- until trim frame -4- is above in‐
take duct -5- for fresh-air blower.
– Pull plenum chamber cover out of cowl panel trim -6-.
Note
If the seal is not pulled off, the tab -2- on the cover -1- could be
damaged irreparably.
Installing
3. Bulkhead 21
Note
♦ It is important that the cowl panel trim -2- and the plenum
chamber cover with trim frame -5- for the intake duct are not
damaged so that no water runs into the air conditioning unit
via the intake duct -4- when the plenum chamber cover is in‐
stalled -1-.
♦ The cowl panel trim at the plenum chamber cover must be
engaged fully in the windscreen frame -3-.
♦ The plenum chamber cover must be inserted properly and fully
in the mounting -arrow- for the cowl panel trim.
3.4.2 Removing and installing cowl panel trim

Removing
– Remove plenum chamber cover ⇒ page 21 .
– Remove wiper arms ⇒ Electrical system; Rep. gr. 92 ; Wind‐
screen wiper system; Removing and installing wiper arms .
– Pull off securing clip -1- -arrow A-.
Caution
Risk of damage to cowl panel trim.

♦ Coat transition between windscreen and cowl panel trim
with a small amount of soap solution.
– Starting at edge of windscreen, carefully pull cowl panel trim

-2- vertically upwards out of retainer -4- at windscreen -3-
-arrows B-.
Installing
Note
♦ It is important that the cowl panel trim is not damaged so that

no water can run into the air conditioning unit via the intake
duct.
♦ The cowl panel trim of the plenum chamber cover must be
engaged completely in the windscreen frame.

55 – Bonnet, rear lid

1 Bonnet
⇒ “1.1 Exploded view - bonnet”, page 23
⇒ “1.2 Exploded view - Bowden cable”, page 27
⇒ “1.3 Removing and installing bonnet”, page 28
⇒ “1.4 Adjusting bonnet”, page 29
⇒ “1.5 Removing and installing hinges”, page 32
⇒ “1.6 Removing and installing striker”, page 33
⇒ “1.7 Removing and installing gas strut”, page 34
⇒ “1.8 Releasing gas from gas strut”, page 35
⇒ “1.9 Removing and installing insulation”, page 35
⇒ “1.10 Removing and installing Bowden cable”, page 36
⇒ “1.11 Removing and installing bonnet lock”, page 39
⇒ “1.12 Removing and installing operating lever for bonnet lock”,
page 39
1.1 Exploded view - bonnet

⇒ “1.1.1 Exploded view - bonnet”, page 23
⇒ “1.1.2 Exploded view - bonnet, bonnet lock”, page 25
⇒ “1.1.3 Exploded view - bonnet, gas strut”, page 26
1.1.1 Exploded view - bonnet
1. Bonnet 23
1 - Cover for bonnet hinge

(right-side)
❑ Clipped in at side
2 - Bonnet
• When removing or instal‐
ling the bonnet, a second
mechanic is required to
support and hold the bon‐
net.
❑ Removing
– Detach gas strut from
bonnet ⇒ page 34 .
– Unscrew nuts -4- at bon‐

net hinge at top.
– Detach bonnet.
❑ Installing: in reverse or‐
der of removal
Note
Check that bonnet closes properly

(bonnet must fall into locks from
equilibrium position and engage
fully).
❑ Adjusting
– Align bonnet between
wings.
– Adjust height of bonnet

via bottom section of
bonnet lock.
– Adjust position of bon‐

net to wings via stop buf‐
fers.
3 - Cover for bonnet hinge (left-side)

❑ Clipped in at side
4 - Bolts
❑ 21 Nm
5 - Bonnet hinge
• For removal and installation, remove bonnet or support it securely.
❑ Removing:
– Remove gas strut ⇒ page 34 .
– Remove bolts -2- and nuts -4-.

❑ Installing: in reverse order of removal
6 - Gas strut
❑ The cylinder end of the gas strut must be installed on the bonnet side.
7 - Ball-head pin
❑ 10 Nm
24 Rep. gr.55 - Bonnet, rear lid

8 - Nut
❑ 8 Nm
9 - Arrester
10 - Nut
❑ 8 Nm
11 - Striker
12 - Arrester
1.1.2 Exploded view - bonnet, bonnet lock
1 - Bonnet lock
❑ Unfasten bumper cover
(top).
❑ Disengage cable at bon‐
net lock.
❑ Unplug electrical con‐
nector.
❑ Remove bolts -1- and
-2-.
Note
Adjust the height of the bonnet by

moving the bonnet lock into the
elongated holes in the lock carrier.
2 - Lock carrier
3 - Bolt
❑ 11 Nm
4 - Electrical wire for bonnet
lock
1. Bonnet 25
1.1.3 Exploded view - bonnet, gas strut
1 - Bonnet
2 - Gas strut
❑ To remove, lift retaining
clip slightly and detach
gas strut from ball-head
pin.
Note
Note correct position when instal‐

ling: cylinder end of gas strut must
be fitted on bonnet.
3 - Suspension turret
4 - Ball-head pin
❑ 21 Nm

1.2 Exploded view - Bowden cable
1 - Bonnet lock (right-side)

⇒ page 25
2 - Bowden cable for bonnet
lock
❑ Removing:
– Disconnect Bowden ca‐
ble from coupling unit
⇒ page 36 .
– Pull Bowden cable to‐
wards engine compart‐
ment.
der of removal
❑ Adjusting trigger point
for bonnet locks
⇒ page 37
3 - Bonnet lock (left-side)
4 - Operating lever
❑ Disengaging Bowden
cable ⇒ page 41
5 - Coupling unit for cable
– Disengage Bowden ca‐
ble to vehicle interior at
this point before remov‐
ing lock carrier and
when removing operat‐
ing lever.
6 - Bowden cable for operating

lever
❑ Bowden cable to oper‐
ating lever in vehicle in‐
terior
7 - Grommet
❑ When installing, make sure it is seated correctly; it must be pressed into partition panel completely.
1. Bonnet 27
1.3 Removing and installing bonnet

⇒ “1.3.1 Renewing impact guard for bonnet”, page 28
⇒ “1.3.2 Removing and installing bonnet seal”, page 29
1.3.1 Renewing impact guard for bonnet
Note
The impact guard is additionally provided with a piece of double-sided adhesive tape.
1 - Clip
2 - Impact guard
❑ To remove, pull clip out
of bonnet and pull off im‐
pact guard
3 - Bonnet

1.3.2 Removing and installing bonnet seal
1 - Seal for plenum chamber

❑ To remove, detach from
body flange by pulling to
front at sides.
❑ To install, position seal
on foam section on one
side (with pre-tension)
and slide onto body
flange.
❑ On opposite side also
position seal on foam
section (with pre-ten‐
sion) and slide onto
body flange.
❑ Gradually press on seal
as far as opposite side
(compress seal along
body flange to take up
any excess length).
2 - Profiled seal (right-side)
❑ To remove, unclip from
wing mounting flange
and suspension turret.
❑ To install, press clips of
foam section into in
body.
3 - Plenum chamber partition
panel
❑ Push plenum chamber
seal on at side.
1.4 Adjusting bonnet

♦ Setting gauge - 3371-
Gap widths at bonnet
1. Bonnet 29
Note
All dimensions are given in mm (tolerance ± 0.5 mm).
♦ Dimension A = 4.5 mm
♦ Dimension B = 4.5 mm
♦ Dimension C = 4.5 mm
♦ Dimension D = 3.0 mm
Stop buffers for height adjustment

1 - Stop buffer
❑ The stop buffers -1-
serve as impact protec‐
tion.
2 - Bonnet
3 - Adjusting buffers
Note
The adjusting buffers -2- are used to

adjust the height of the bonnet.
❑ When bonnet is closed,
adjusting buffers -2-
must rest on lock carrier.
1. Bonnet 31
1.5 Removing and installing hinges
1 - Bonnet
2 - Bonnet hinge
❑ Removing
– Before removing bonnet
hinge, support bonnet or
secure it in position.
– Remove gas strut

⇒ page 34 .
– Remove bolts -4- and

nuts -5-.
❑ Installing
– In reverse sequence
(align according to
markings -arrows-)
3 - Cover
❑ Clipped into side of bon‐
net hinge
4 - Gas strut
❑ Engage cylinder end of
gas strut on bonnet end
⇒ page 34
5 - Wing mounting flange
6 - Bolt
❑ 21 Nm
7 - Nut
❑ 21 Nm

1.6 Removing and installing striker

⇒ “1.6.1 Removing and installing arrester at bonnet”, page 33
⇒ “1.6.2 Removing and installing arrester at lock carrier”,
page 33
⇒ “1.6.3 Removing and installing striker”, page 33
1.6.1 Removing and installing arrester at bon‐

net
Removing
– Unscrew nuts -1- and detach arrester bracket -2-.
Installing
Tightening torques
♦ ⇒ “1.1.1 Exploded view - bonnet”, page 23
1.6.2 Removing and installing arrester at lock

carrier
Removing
– Remove lock carrier cover.
– Remove bolts -1- and detach arrester -2- from lock carrier
-3-.
– When installing, tighten bolts to 5 Nm.
Installing
Tightening torques
♦ ⇒ “1.1.1 Exploded view - bonnet”, page 23
1.6.3 Removing and installing striker
1. Bonnet 33
1 - Nut
❑ Tightening torque
⇒ page 23
2 - Striker
❑ Removing
– Unscrew bolts and de‐
tach striker.
❑ Installing
– Align striker according
to markings in bonnet
-arrows- and tighten
bolts to specified torque.
3 - Bonnet
1.7 Removing and installing gas strut

Removing
– Support bonnet or secure it in position.
– Lift retaining clip -arrow- slightly using a small screwdriver, and
pull gas strut -1- off ball-head pin -2-.
– Perform same steps at ball-head pin (bottom).
Installing
Note
If the gas strut has been completely removed make sure it is re-
installed in the correct position. The cylinder end of the gas strut
must be engaged on the bonnet side.
– Press gas strut onto ball-head pin and make sure it engages.

1.8 Releasing gas from gas strut

Procedure
– Clamp section -x = 50 mm- of gas strut in a vice.
WARNING
♦ Only the section indicated may be clamped in the vice

(accident risk!).
♦ Always wear safety goggles while sawing.
Note
Cover area around saw cut with a cloth to catch any fluid which
may escape.
– Saw open cylinder of gas strut in first third of overall cylinder

length, based on reference edge at piston-rod end.
1.9 Removing and installing insulation
1 - Retaining clip
2 - Lining for bonnet
❑ Installing:
– First push lugs on rear
edge of lining into holes
provided on inner panel.
– Push in lugs on front

edge and side.
– Retaining clips must en‐

gage audibly when
pressing in.
– Press in clip.
3 - Bonnet
4 - Clip
1. Bonnet 35
1.10 Removing and installing Bowden cable

Coupling unit for Bowden cable ⇒ page 36
Engaging Bowden cable in bonnet lock ⇒ page 37
Engaging Bowden cable in operating lever ⇒ page 37
Routing of Bowden cable in vehicle interior ⇒ page 37
Routing of Bowden cable in engine compartment ⇒ page 38
Coupling unit for Bowden cable:
– Pull clips -1- off lugs and lift out Bowden cables -8- and -9-
going to bonnet locks on both sides.
– To remove coupling unit -2-, release catches -arrows- at lock
carrier -3- from front and push coupling unit towards rear out
of bracket for arrester.
– Engage Bowden cable -4- to vehicle interior in roller -5- of
coupling unit, as shown.
– Press Bowden cable into mounting on housing.
– Press housing cover -7- on so that arrow points in direction of
Bowden cable to vehicle interior.

– Adjust Bowden cable -8- via collar -6- so that bonnet locks are
released simultaneously.
Engaging Bowden cable in rear lid lock:
– Insert nipple of Bowden cable -2- into operating lever
-right arrow- of bonnet lock -1-.
– Slide Bowden cable with guide into bonnet lock from below;
catch -left arrow- should engage.
Engaging Bowden cable in operating lever:

– Insert Bowden cable -2- in operating lever -1- from side in di‐
rection of -arrow-.
– Swivel Bowden cable -2- upwards as shown and clip it into

support bracket of operating lever -1-.
Routing of Bowden cable in vehicle interior:

– Route Bowden cable -2- along A-pillar as shown.
– Grommet -1- must be pressed onto A-pillar from interior.
1. Bonnet 37
Routing of Bowden cable in engine compartment:
– Starting from interior, route Bowden cable -3- in engine com‐

partment along wing mounting flange -2- (as shown).
– Make sure that grommet -1- is pressed into side of A-pillar
correctly.
– Push coupling unit -4- into lock carrier ⇒ page 36 .
– Slide Bowden cable onto lugs -5- with clips -6-.

1.11 Removing and installing bonnet lock

Removing
– Unplug connector -4- for anti-theft alarm system.
– Pull connector off lock carrier.
– Detach retaining clips and move Bowden cable -1- clear.
– Unscrew bolts -3-.
– Release retaining hook at Bowden cable -left arrow- and slide

downwards out of bonnet lock -1- with guide.
– Disengage nipple of Bowden cable from operating lever
-right arrow-.
Installing
Tightening torques
♦ ⇒ “1.1.2 Exploded view - bonnet, bonnet lock”, page 25
1.12 Removing and installing operating lever

for bonnet lock
⇒ “1.12.1 Removing and installing cover for operating lever”, page
39
⇒ “1.12.2 Removing and installing operating lever”, page 41
1.12.1 Removing and installing cover for operating lever
1. Bonnet 39
1 - Operating lever
2 - A-pillar trim (bottom)
3 - Retaining clip
❑ Press in fully (must en‐
gage).
4 - Cover for operating lever
❑ Before removing, disen‐
gage cable in coupling
unit in engine compart‐
ment ⇒ page 36 .
❑ Lever retaining clip out
of operating lever.
❑ Detach cover from oper‐
ating lever at side.

1.12.2 Removing and installing operating lever
1 - Mounting bracket for oper‐

ating lever
❑ Cover for operating lev‐
er removed
❑ A-pillar trim (bottom) re‐
moved
❑ Unscrew bolts -3- and
disengage cable -1-.
2 - Clip
3 - Bowden cable
❑ Clip support bracket for
Bowden cable into
mounting bracket, as
shown in detail view.
4 - Bolts
❑ 2 Nm
1. Bonnet 41
2 Rear lid
⇒ “2.1 Exploded view - rear lid”, page 42
⇒ “2.2 Removing and installing rear lid”, page 49
⇒ “2.3 Adjusting rear lid”, page 54
⇒ “2.4 Removing and installing hinges”, page 60
⇒ “2.5 Removing and installing rear lid seal”, page 63
⇒ “2.6 Removing and installing gas strut”, page 65
⇒ “2.7 Releasing gas from gas strut”, page 66
⇒ “2.9 Removing and installing actuating mechanism”,
page 68
⇒ “2.10 Removing and installing rear lid power opening control
unit J938 ”, page 74
⇒ “2.11 Removing and installing rear lid power opening sender
G750 / G760 ”, page 75
⇒ “2.12 Removing and installing rear lid lock”, page 77
⇒ “2.13 Removing and installing extension spring”, page 81
2.1 Exploded view - rear lid

⇒ “2.1.1 Exploded view - rear lid, Saloon”, page 42
⇒ “2.1.2 Exploded view - rear lid, cable guide for rear lid hinge,
Saloon”, page 44
⇒ “2.1.3 Exploded view - rear lid, Avant”, page 45
⇒ “2.1.4 Exploded view - rear lid, motor for rear lid, Saloon”, page
46
⇒ “2.1.5 Exploded view - rear lid, motor for rear lid, Avant”,
page 47
⇒ “2.1.6 Exploded view - rear lid power opening sender”,
page 48
2.1.1 Exploded view - rear lid, Saloon

1 - Rear lid
⇒ page 49
2 - Stop strip
3 - Adjusting buffer
❑ Adjusting ⇒ page 58
4 - Rear lid lock
⇒ page 77
5 - Nut
❑ 21 Nm
6 - Spring
❑ Attachment points
⇒ page 81
7 - Rear lid hinge
⇒ page 60
8 - Nut
❑ 21 Nm
9 - Bracket
10 - Nut
❑ 21 Nm
11 - Bolt
❑ 21 Nm
12 - Bolt
❑ 21 Nm
13 - Motor 1 for rear lid - V444-
⇒ page 68
14 - Lateral stop
2. Rear lid 43
2.1.2 Exploded view - rear lid, cable guide for rear lid hinge, Saloon
1 - Cable guide for rear lid

hinge
⇒ General body repairs,
interior; Rep. gr. 70 ;
Luggage compartment
trim panels; Removing
and installing rear lid
trim (bottom)
2 - Fastener
3 - Manual release for rear lid
❑ Routing ⇒ page 78
4 - Rear lid hinge
5 - Lug
6 - Rear lid

2.1.3 Exploded view - rear lid, Avant
1 - Rear lid
⇒ page 51
2 - Rear lid lock
⇒ page 78
3 - Cover
4 - Nuts
❑ 21 Nm
5 - Cover
7 - Bolts
❑ 8 Nm
8 - Stop plate
9 - Bolt
❑ 8 Nm
10 - Bolt
❑ 21 Nm
11 - Bolt
❑ 30 Nm
13 - Rear lid hinge
⇒ page 61
14 - Ball-head pin
❑ 21 Nm
15 - Gas strut
❑ Damping element must be engaged at rear lid end.
❑ To install, press onto ball-head pin (turn while pressing on)
2. Rear lid 45
2.1.4 Exploded view - rear lid, motor for rear lid, Saloon

⇒ page 68
2 - Ball-head pin
❑ 20 Nm
3 - Rear lid hinge
4 - Bolt
❑ 21 Nm
5 - Bracket
6 - Plastic clip
❑ Use long-nose pliers to
release ⇒ page 66

2.1.5 Exploded view - rear lid, motor for rear lid, Avant

⇒ page 69
2 - Bolt
❑ 21 Nm
3 - Electrical connector
nector before removing
drive unit.
4 - Bracket
❑ The bracket has been
positioned at the factory
using a special device
and must not be moved
out of this position.
5 - Bolt
❑ 8 Nm
6 - Roof frame
7 - Bolt
❑ Thread-forming
⇒ Item 7 (page 73)
8 - Rear lid hinge
⇒ page 61
2. Rear lid 47
2.1.6 Exploded view - rear lid power opening sender
1 - Clip
❑ 7x
2 - Rear lid power opening
sender - G750-
⇒ page 75
3 - Rear lid power opening con‐
trol unit - J938-
⇒ page 74
4 - Bolt
❑ 2.1 Nm
5 - Bracket
6 - Rear lid power opening
sender 2 - G760-
⇒ page 75
7 - Clip
❑ 5x

2.2 Removing and installing rear lid

⇒ “2.2.1 Removing and installing rear lid - Saloon”, page 49
⇒ “2.2.2 Removing and installing rear lid - Avant”, page 51
⇒ “2.2.3 Removing and installing lateral stops - Saloon up to
model year 2014”, page 52
⇒ “2.2.4 Removing and installing stop and adjusting buffer -
Avant”, page 53
2.2.1 Removing and installing rear lid - Saloon
1 - Rear lid
• When removing or instal‐
ling the rear lid, a second
mechanic is required to
support and hold the rear
lid.
❑ Removing:
Note
Before removing, mark the position

of the rear lid on the lid hinge using
a fine felt-tip pen or similar.
– Remove rear lid trim ⇒

General body repairs,
Luggage compartment
trim (bottom) .
– Unplug electrical wiring

at connectors and pull
out of rear lid.
– Unscrew nuts on rear lid

and lift off rear lid.
der of removal
❑ Springs -6- must be en‐
gaged before rear lid is
installed.
❑ Adjusting:
– Adjust height of rear lid
at front and adjust
lengthwise via rear lid
hinge.
– Adjust height of rear lid at rear via rear lid lock at striker plate.
– Align rear lid centrally with equal gaps on both sides / to specified gap widths ⇒ page 54 .
– Adjust stop buffers.

❑ Removing and installing rear lid seal ⇒ page 63
❑ If fitted, reversing camera - R189- must be re-calibrated ⇒ Communication; Rep. gr. 91 ; Reversing
camera system .
❑ On vehicles with overhead view camera, rear overhead view camera - R246- must be re-calibrated ⇒
Communication; Rep. gr. 91 ; Overhead view camera .
2. Rear lid 49
2 - Stop strip
4 - Rear lid lock
5 - Nut
6 - Spring
7 - Rear lid hinge
8 - Nut
❑ 21 Nm
9 - Bracket
10 - Nut
❑ 21 Nm
11 - Bolt
❑ 21 Nm
12 - Bolt
❑ 21 Nm
14 - Lateral stop

2.2.2 Removing and installing rear lid - Avant
1 - Rear lid
❑ Removing:
Luggage compartment
trim (top) .
– Unplug electrical con‐

nectors and disconnect
hose for rear window
washer system.
– A second person is re‐

quired to support and lift
off the rear lid.
– Detach gas struts from

rear lid.
– Unscrew bolts from

hinge on rear lid (left and
right).
– Lift off rear lid.

der of removal
– Adjust rear lid
⇒ page 54 .
❑ If fitted, reversing cam‐
era - R189- must be re-
calibrated ⇒ Communi‐
cation; Rep. gr. 91 ;
Reversing camera sys‐
tem .
❑ On vehicles with over‐
head view camera, rear overhead view camera - R246- must be re-calibrated ⇒ Communication; Rep.
gr. 91 ; Overhead view camera .
2 - Rear lid lock
3 - Cover
4 - Nuts
5 - Cover
7 - Bolts
8 - Stop plate
9 - Bolt
10 - Bolt
❑ 21 Nm
11 - Bolt
❑ 30 Nm
2. Rear lid 51

13 - Rear lid hinge
14 - Ball-head pin
15 - Gas strut
❑ Damping element must be engaged at rear lid end.
❑ To install, press onto ball-head pin (turn while pressing on)
2.2.3 Removing and installing lateral stops - Saloon up to model year 2014
1 - Stop on body
❑ Removing ⇒ page 53
– To install stop, insert it
correctly in bore and
press slide in complete‐
ly.
2 - Stop on rear lid

– To install stop, insert it
correctly in bore and
press slide in complete‐
ly.
3 - Rear lid
4 - Side panel

Removing lateral stop

– Pull slide -1- out of stop in direction of -arrow-.
– Pull stop out of side panel/rear lid.
2.2.4 Removing and installing stop and adjusting buffer - Avant
2 - Stop plate
3 - Bolt
❑ 8 Nm
4 - Bolt
❑ 8 Nm
Installation position of adjusting buffer
2. Rear lid 53
1 - Rear lid
❑ If correctly adjusted, ad‐
justing buffer -3- must
be slightly compressed
on coming into contact
with stop buffer -2- with
rear lid closed.
2 - Stop plate
❑ The height is adjusted
via the adjuster screw.
❑ If correctly adjusted, ad‐
justing buffer must be
slightly compressed on
coming into contact with
stop buffer (on rear lid)
with rear lid closed.
4 - Side panel
2.3 Adjusting rear lid

⇒ “2.3.1 Adjusting rear lid - gap widths”, page 54
⇒ “2.3.2 Adjusting rear lid - vehicles with fixed striker”,
page 56
⇒ “2.3.3 Adjusting rear lid - vehicles with power latching motor for
rear lid V382 ”, page 57
⇒ “2.3.4 Adjusting rear lid at adjusting buffers - Saloon”,
page 58
⇒ “2.3.5 Adjusting rear lid at adjusting buffers - Avant”,
page 59
2.3.1 Adjusting rear lid - gap widths


Gap widths - Saloon
The gap widths can be checked using the setting gauge - 3371- .
♦ Dimension -A- = 3.5 mm
♦ Dimension -B- = 5.5 mm
♦ Dimension -C- = 2.2 mm
♦ Dimension -D- = 2.2 mm
2. Rear lid 55
♦ Dimension -E- = 3.5 mm

♦ Dimension -F- = 5.0 mm
Gap widths - Avant
♦ Dimension -A- = 3.5 mm

♦ Dimension -B- = 4.5 mm
♦ Dimension -C- = 2.2 mm all around
♦ Dimension -D- = 2.3 mm
♦ Dimension -E- = 3.5 mm
♦ Dimension -F- = 5.0 mm
♦ Make sure gap is parallel to body.
2.3.2 Adjusting rear lid - vehicles with fixed

striker
Procedure
– Remove rear cross panel trim ⇒ General body repairs, interior;
Rep. gr. 70 ; Luggage compartment trim panels; Removing
and installing lock carrier trim .

Note
Prior to adjustment, completely screw in adjusting buffers on rear

lid: Saloon ⇒ page 58 , Avant ⇒ page 59 .
– Unfasten nuts -1, 3-; it should be possible to move striker -2-.

– Close rear lid and check alignment with body contour.
– If necessary, align according to body contour via stop buffers
(top).
– Rear lid lock must be engaged in main catch (2nd stop).
– Open rear lid and tighten nuts.
– Unscrew stop buffers (bottom) until buffers of closed rear lid
make contact with stops in body.
– Check whether rear lid still closes easily. Repeat adjustment
procedure if necessary.
– If rear lid does not close easily, screw in stop buffers slightly.
Tightening torques
♦ Striker to body: 21 Nm
2.3.3 Adjusting rear lid - vehicles with power

latching motor for rear lid - V382-
Procedure
– Remove rear cross panel trim ⇒ General body repairs, interior;
– Loosen nuts; it must still be possible to move rear lid lock unit
-1- with striker -2-.
2. Rear lid 57
– To make adjustment easier, there are marks in rear cross

panel for aligning rear lid lock unit.
Caution
Risk of damage!
♦ When adjusting the rear lid, the striker must be in the “rear
lid closed” position (bottom end position).
♦ The striker must not be fitted in the top end position -1-
(marked in white), as otherwise the rear lid could be pulled
down too far when it is closed and could become dam‐
aged.
♦ The power latching control unit must not be electrically
connected when adjusting the rear lid.
– Before adjusting the rear lid, completely screw in the top parts
of the adjusting buffers on the rear lid ⇒ page 59 .
– Close rear lid and check body contour.
– If necessary, align according to body contour via adjusting
buffers (top).
– Rear lid lock must be engaged in main catch (2nd stop).
– Tighten nuts -1- on rear lid lock unit -2- to specified torque.
– Unscrew adjusting buffers (bottom) until buffers of closed rear
lid make contact with stop buffers in body.
– If rear lid does not close easily, screw in adjusting buffer slight‐
ly.
Tightening torques
♦ Power latching motor for rear lid to body: 21 Nm
2.3.4 Adjusting rear lid at adjusting buffers -

Saloon
Procedure
– Close rear lid.
Note
With the rear lid correctly adjusted and closed, the adjusting buf‐
fers -2- must rest lightly against the body.
– The adjusting buffers are screwed in or out as necessary (ac‐

cording to the body contour).

– The stops -3- must audibly engage when pressed in; rear lid
trim -1- must be installed.
– Check gap widths ⇒ page 55 .
– Unscrew adjusting buffer until stop buffers of closed rear lid
make contact with luggage compartment trim.
– If rear lid does not close easily, screw in adjusting buffer slight‐
ly.
2.3.5 Adjusting rear lid at adjusting buffers -

Avant
Procedure
Note
Gas struts must be fitted before adjusting new rear lid.
– Before adjusting rear lid, screw adjuster screw -2- with pro‐
tective cap -1- completely into adjusting buffer -3-.
– Unscrew adjuster screw until protective cap is slightly com‐
pressed when it comes into contact with stop on rear lid with
rear lid closed.
– Check that rear lid has no play and closes in line with body
contour by pressing or pulling on side edges of rear lid beneath
rear window.
– Repeat adjustment if necessary.
Installing stop
– When fitting stop -2-, tighten bolt -1- to specified torque
⇒ Item 3 (page 53) .
– Height adjustment is performed via adjusting buffers on body.
2. Rear lid 59
2.4 Removing and installing hinges

⇒ “2.4.1 Removing and installing hinges - Saloon”, page 60
⇒ “2.4.2 Removing and installing hinges - Avant”, page 61
⇒ “2.4.3 Removing and installing cover for rear lid hinge”,
page 62
2.4.1 Removing and installing hinges - Saloon
Note
♦ When renewing the hinges on both sides, remove and install

them one after the other (left and right).
♦ Before removing, mark position of hinges on rear lid and on
body.
♦ Use marks on rear lid hinge for adjustment in longitudinal di‐
rection.
1 - Rear lid hinge
Note
Prop up and secure rear lid with the

help of a second person.
❑ Luggage compartment
side trim removed ⇒
Luggage compartment
and installing luggage
compartment side trim
– Remove rear lid trim
(bottom) ⇒ General
body repairs, interior;
Rep. gr. 70 ; Luggage
compartment trim pan‐
els; Removing and in‐
stalling rear lid trim (bot‐
tom) .
– First remove nuts -3-

from rear lid.
– Unscrew bolts -2- from

side panel and detach
hinge.
– When installing, align

according to marks and
tighten bolts and nuts to
torque.
– Check gap widths

⇒ page 55 .
2 - Bolt
❑ 21 Nm
3 - Nut
❑ 21 Nm

4 - Bracket
2.4.2 Removing and installing hinges - Avant
Note
♦ On vehicles with electric rear lid operation, the drive units for
the rear lid must be removed first ⇒ page 69 .
♦ When installing, observe tightening sequence for bolts.
1 - Rear lid hinge

Removing:
– Lower headliner ⇒ Gen‐

eral body repairs, interi‐
or; Rep. gr. 70 ; Roof
and installing moulded
headliner .
– Pull off cover for rear lid

hinge ⇒ page 62 .
Note
To prevent any damage to the rear

lid or body, prop up and secure the
rear lid.
– Remove bolts -3- from

rear lid.
– Remove bolt -1- and

hexagon nut -4- and de‐
tach hinge.
Installing:
– Insert hinge in body and

loosely attach it to roof
frame with nut -4-.
– Then loosely secure

hinge to side with bolt
-3-.
– Secure hinge loosely

with bolts -2-.
– Align rear lid on left and

right and tighten bolts -2- to torque.
– Adjust height of rear lid relative to roof and tighten bolt -3- and nut -4- to torque.
– Press on hinge cover.
2 - Bolt
❑ 30 Nm
3 - Bolt
❑ 21 Nm
2. Rear lid 61
4 - Hexagon nut
❑ 21 Nm
2.4.3 Removing and installing cover for rear

lid hinge
Removing
– Cover is pressed onto rear lid hinge.
– Release side fasteners of cover -1- and detach from rear lid
hinge -2-.
Installing
– When installing, position the retaining tabs in engaging holes
at hinge arm and then fully press on cover on opposite side.
– Cover must engage audibly.

2.5 Removing and installing rear lid seal

⇒ “2.5.1 Renewing rear lid seal - Saloon”, page 63
⇒ “2.5.2 Renewing additional seal for rear lid”, page 63
⇒ “2.5.3 Renewing rear lid seal - Avant”, page 64
2.5.1 Renewing rear lid seal - Saloon
1 - Rear lid
2 - Rear lid seal
– To remove, pull seal off
body flange.
Note
To renew seal, clean body flange

and fit new seal.

butt joint -arrow- on seal
with marking in centre of
vehicle.
– Starting from butt joint,

press seal onto body
flange all around.
2.5.2 Renewing additional seal for rear lid

2. Rear lid 63
♦ Hot air blower - V.A.G 1416-
♦ Roller - 3356-
♦ Cleaning solution - D 009 401 04-

– Pull clip out of additional seal (both sides).
– Heat rear lid in area around additional seal using hot air blower
and pull off seal gradually.
– Remove any residual adhesive in bonding area.
– Clean bonding surface with cleaning solution - D 009 401 04- .
– Position additional seal at seals (both sides) and slide clips in.
– Fit additional seal so that it matches exact contour of rear lid,
gradually pull out protective film between seal and rear lid us‐
ing removal aids, and press seal on firmly by hand.
After installing, press on additional seal again with roller - 3356- .
2.5.3 Renewing rear lid seal - Avant

1 - Rear lid
2 - Rear lid seal
❑ Removing
– Rear cross panel trim
removed ⇒ General
stalling lock carrier trim
– Have a second person

hold rear lid to prevent it
from closing and pull
gas strut (body end) off
ball-head pins (left and
right).
– Pull seal off all around

body flange.
❑ Installing
Note
Before installing, hinge must be un‐

fastened from rear lid so that seal
can be inserted between rear lid
(front edge of spoiler) and roof.
– Remove rear lid trim

(top) ⇒ General body
repairs, interior; Rep.
gr. 70 ; Luggage com‐
partment trim panels;
Removing and installing
rear lid trim (top) .
– Have a second person

hold rear lid in place and unscrew hinge bolts from rear lid on one side.
– Press up rear lid until seal can be inserted.
– Bring rear lid back to original position, screw bolts back in and tighten to specified torque
– When installing, align seal according to marking at top -arrow- and press onto body flange all around.
3 - Body flange
2.6 Removing and installing gas strut

⇒ “2.6.1 Removing and installing gas strut with metal clip”,
page 65
⇒ “2.6.2 Removing and installing gas strut with plastic clip”, page
66
2.6.1 Removing and installing gas strut with

metal clip
Removing
– Support rear lid or secure it in position.
2. Rear lid 65
– Lift retaining clip -1- slightly using a small screwdriver, and pull
gas strut -2- off ball stud.
Installing
– Press gas strut onto ball-head pin until it engages audibly.
2.6.2 Removing and installing gas strut with

plastic clip
Removing
– Support rear lid or secure it in position.
– Squeeze clip -1- with long-nose pliers and pull gas strut -2- off
ball-head pin.
Installing
– Press gas strut onto ball-head pin until it engages audibly.
2.7 Releasing gas from gas strut

Procedure
– Clamp section -x = 50 mm- of gas strut in a vice.
WARNING
♦ Only the section indicated may be clamped in the vice

(accident risk!).
♦ Always wear safety goggles while sawing.
Note
Cover area around saw cut with a cloth to catch any fluid which
may escape.
– Saw open first third of cylinder part of gas strut (measured from
piston rod end of cylinder).


⇒ “2.8.1 Removing and installing striker”, page 67
⇒ “2.8.2 Removing and installing striker - vehicles with power
latching motor for rear lid V382 ”, page 67
2.8.1 Removing and installing striker

Removing
– Remove lock carrier trim ⇒ General body repairs, interior;
– Unscrew nuts -1- and -3- and detach striker -2-.
Installing
– Insert striker, making sure it is positioned correctly.
• The round side -arrow- of the striker must face upwards.
– Adjust striker ⇒ page 56 .
Tightening torques
♦ 23 Nm
2.8.2 Removing and installing striker - vehi‐

cles with power latching motor for rear
lid - V382-
Removing
– Remove lock carrier trim ⇒ General body repairs, interior;
2. Rear lid 67
– Unscrew nuts -2 and 4- and detach rear lid lock unit -3-.
– Unplug electrical connector -1-.
Installing
Note
♦ The striker must only be installed in the “rear lid closed” posi‐
tion.
♦ A new striker is always set to the “rear lid closed” position.
– If the same striker is re-installed, plug in electrical connector

at power latching control unit and, with rear lid open, lock rotary
latch in rear lid lock using a screwdriver or similar tool.
• The power latching system moves to the “rear lid closed” po‐
sition = basic setting.
– Unplug electrical connector at power latching control unit.
– Open rear lid lock by pressing release button for rear lid lock
cylinder.
Tightening torques
♦ 23 Nm
2.9 Removing and installing actuating

mechanism
⇒ “2.9.1 Removing and installing motor 1 for rear lid V444 - Sa‐
loon”, page 68
⇒ “2.9.2 Removing and installing motor for rear lid V444 / V445 -
Avant”, page 69
⇒ “2.9.3 Removing and installing rear lid control unit J605 - Sa‐
loon”, page 73
⇒ “2.9.4 Removing and installing rear lid control unit J605 -
Avant”, page 73
2.9.1 Removing and installing motor 1 for rear

lid - V444- - Saloon
WARNING
When the motor 1 for rear lid - V444- has been removed and
installed, it has to be adapted via the Guided Functions mode
in the Guided Fault Finding routine (diagnostic address 6D)
⇒ Vehicle diagnostic tester.


❑ Removing
nector for motor.
– Pull motor 1 for rear lid -

V444- off ball-head pin
(rear).
– Remove bolts from

bracket -5- and lift mo‐
tor 1 for rear lid - V444-
out of vehicle.
– Pull motor 1 for rear lid -

V444- off ball-head pin
on bracket.
❑ Installing
– First press motor 1 for
rear lid - V444- onto ball-
head pin on bracket and
secure both compo‐
nents together in vehicle
with bolts.
2 - Ball-head pin
❑ 20 Nm
3 - Rear lid hinge
4 - Bolt
❑ 21 Nm
5 - Bracket
6 - Plastic clip
❑ Must be released using
long-nose pliers
⇒ page 66
2.9.2 Removing and installing motor for rear

lid -V444- / -V445- - Avant
WARNING
When the motor 1 for rear lid - V444- or motor 2 for rear lid -
V445- has been removed and installed, it has to be adapted
via the Guided Functions mode in the Guided Fault Finding
routine (diagnostic address 6D) ⇒ Vehicle diagnostic tester.
2. Rear lid 69

❑ Roof end trim removed
⇒ General body repairs,
Roof trim panels; Re‐
moving and installing
roof end trim
❑ Unfasten D-pillar trim in
area of drive unit and, if
necessary, push care‐
fully to the side.
❑ The D-pillar trim must be
removed completely on
vehicles with electric
luggage compartment
cover.
Note
♦ Drive unit must only be removed

and installed with rear lid fully
open.
♦ Unfasten lock nut at eccentric pin
before removing drive unit.
nector -2-.
❑ Unfasten lock nut at
drive unit ⇒ page 72 .
Note
The eccentric pin

⇒ Item 1 (page 72) must be seated
loosely in the hole in the hinge arm.
❑ If necessary, slacken
the tension on the ec‐
centric pin by turning it slightly clockwise.
❑ Unscrew bolt -5- at bracket -4-.
❑ Unscrew bolt at hinge arm ⇒ Item 7 (page 73) and detach drive unit -1- by pulling it to the side.
2 - Bolt
❑ 21 Nm
❑ Unplug electrical connector before removing drive unit.
4 - Bracket
Note
♦ The bracket has been positioned

at the factory using a special de‐
vice and must not be moved out
of this position.
♦ If the bracket has to be renewed,
e.g. in the case of accident re‐
pairs, proceed as follows:
❑ Rear lid must be installed together with gas struts.
❑ First attach bracket -4- loosely to drive unit using bolt -5-.
❑ It must still be possible to move the bracket.

❑ Push the drive unit parallel with the rear lid hinge pin until it makes full contact with the drive unit bush.
Caution
Drive unit bush must
make full contact with
hinge pin collar.
❑ Use bolt -3- to fasten bracket -4- on body and tighten bolt to 21 Nm.
❑ Tighten bolt -5- to 8 Nm.
❑ Secure eccentric pin to drive unit with lock nut (tightening torque ⇒ page 72 ).
Note
♦ When the lock nut is tightened,

the eccentric pin in the hinge is
tensioned so that it is free of play.
♦ You must therefore not use an
open-ended spanner to counter‐
hold the hexagon flats of the ec‐
centric pin while you are tighten‐
ing the lock nut.
♦ When removing the drive unit,
this tension can be slackened by
turning the hexagon flats at the
eccentric pin slightly clockwise
after you have loosened the lock
nut.
❑ Tighten bolt at drive fork ⇒ Item 7 (page 73) to specified torque.
5 - Bolt
❑ 8 Nm
6 - Roof frame
7 - Bolt
❑ Thread-forming
❑ Tightening torque ⇒ Item 7 (page 73)
8 - Rear lid hinge
Installing motor 2 for rear lid - V445- in hinge
2. Rear lid 71
1 - Eccentric pin with hexagon

flats
Note
♦ When the lock nut is tightened,

the eccentric pin in the hinge is
tensioned so that it is free of play.
♦ You must therefore not use an
open-ended spanner to counter‐
hold the hexagon flats of the ec‐
centric pin while you are tighten‐
ing the lock nut.
♦ When removing the drive unit,
this tension can be slackened by
turning the hexagon flats at the
eccentric pin slightly clockwise
after you have loosened the lock
nut.
2 - Washer
3-
Lock nut
❑ Loosen lock nut at ec‐
centric pin before re‐
moving drive unit.
❑ If necessary, slacken
tension on eccentric pin
in the hinge arm by turn‐
ing hexagon flats slight‐
ly clockwise.
❑ Self-locking
❑ 6 Nm
❑ When installing, slide
side of drive with bush
-arrow B- and loose eccentric pin -arrow A- onto hinge.
Note
Drive unit bush must make full con‐

tact with hinge pin collar.
❑ This causes arm of drive unit to move into correct position on hinge arm of rear lid hinge -8-.
❑ Tighten bolt -6- to torque to secure drive unit to bracket -5-.
❑ Tighten lock nut -3- to torque.
❑ Tighten bolt -7- to specified torque.
5 - Bracket
Note
♦ The bracket has been positioned

at the factory using a special fix‐
ture and should not be moved
out of this position.
♦ If the bracket has to be renewed,
e.g. in the case of accident re‐
pairs, proceed as described

6 - Bolt
❑ 8 Nm
7 - Bolt
❑ Thread-forming
❑ 21 Nm
8 - Hinge for rear lid
2.9.3 Removing and installing rear lid control

unit - J605- - Saloon
Removing
– Remove luggage compartment side trim ⇒ General body re‐
pairs, interior; Rep. gr. 70 ; Luggage compartment trim panels;
Removing and installing luggage compartment side trim .
– Unplug electrical connectors at control unit.
– Lift catches -arrows- and slide control unit -1- out towards rear.
Installing
– To install control unit, insert it in retainer and slide it forwards
until catches engage.
2.9.4 Removing and installing rear lid control

unit - J605- - Avant
Removing
– Remove roof trim (rear) ⇒ General body repairs, interior; Rep.
gr. 70 ; Roof trim panels; Removing and installing roof end
trim .
– Unplug electrical connectors.
– Lift catches -arrows- and slide control unit -1- out towards side.
Installing
– To install control unit, insert it in retainer and slide forwards
until catch engages.
2. Rear lid 73
2.10 Removing and installing rear lid power

opening control unit - J938-
WARNING
Risk of leg injuries.

♦ Keep away from the swivel range of the ball coupling when
releasing the towing bracket.
Removing
– Extend ball head of towing bracket ⇒ Owner's Manual .
– Unscrew bolts -arrows- in base plate for bumper cover.

– Press control unit -3- off retainers on bumper cover -arrows-.

– If control unit is being renewed, release retaining tab -3-

-arrow- and disengage bracket -2- on control unit -1-.
Installing
Tightening torques
♦ ⇒ “2.1.6 Exploded view - rear lid power opening sender”, page
48
♦ ⇒ “2.1 Exploded view - bumper cover”, page 252
2.11 Removing and installing rear lid power

opening sender -G750- / -G760-
⇒ “2.11.1 Removing and installing rear lid power opening senders
G750 / G760 - vehicles without towing bracket”, page 75
⇒ “2.11.2 Removing and installing rear lid power opening senders
G750 / G760 - vehicles with towing bracket”, page 76
2.11.1 Removing and installing rear lid power

opening senders -G750- / -G760- - ve‐
hicles without towing bracket
Removing
2. Rear lid 75

– Cut through cable tie -2-.
– Remove senders -3, 4- from clips -arrows-.
Installing
– Rear lid power opening sender 2 - G760- must be secured at
bumper cover (top).
• Identification: pins 4 and 5 on connector
Tightening torques
2.11.2 Removing and installing rear lid power

opening senders -G750- / -G760- - ve‐
hicles with towing bracket
Removing
– Detach mounting -1- with sender.

– Take sender -2- out of clips.
Installing
– Rear lid power opening sender 2 - G760- must be secured at
bumper cover (top).
• Identification: pins 4 and 5 on connector
Tightening torques

2.12 Removing and installing rear lid lock

⇒ “2.12.1 Removing and installing rear lid lock - Saloon”,
page 77
⇒ “2.12.2 Removing and installing rear lid lock - Avant”,
page 78
⇒ “2.12.3 Removing and installing manual release for rear lid lock
- Saloon”, page 78
2.12.1 Removing and installing rear lid lock - Saloon
1 - Cover
❑ Before removing rear lid
trim, detach from rear lid
lock.
2 - Rear lid lock
❑ Before removing, de‐
tach cover for rear lid
lock.
❑ Rear lid trim removed ⇒
Luggage compartment
trim (bottom)
nector.
❑ Unscrew nuts and de‐
tach rear lid lock.
❑ Pull rear lid lock with clip
out of centring hole.
3 - Nut
❑ 21 Nm
4 - Cover for rear lid lock
❑ Cover should engage
audibly in rear lid lock on
installation.
5 - Bowden cable
❑ Country-specific version
2. Rear lid 77
2.12.2 Removing and installing rear lid lock - Avant
1 - Cover for rear lid lock

❑ When installing, cover
must engage audibly in
rear lid lock.
❑ To install, fit cover on
rear lid lock.
2 - Nuts
❑ 21 Nm
3 - Cover
❑ Press cover onto lock
until clip engages audi‐
bly.
4 - Rear lid lock
– Pull cover for rear lid
lock off.
❑ Remove rear lid trim ⇒
Luggage compartment
trim (bottom) .
– Pull off cover -3-.

nector for rear lid lock.
– Unscrew nuts -2- and

detach rear lid lock.
6 - Rear lid
2.12.3 Removing and installing manual release

for rear lid lock - Saloon
Routing on rear lid ⇒ page 78
Routing on body ⇒ page 79
Note
The manual release is fitted only for vehicles with a rigid back
panel.
Routing on rear lid:

1 - Bowden cable
Note
♦ When fitting a new Bowden ca‐

ble, it must be routed from the
rear lid lock on the inside of the
rear lid along the rear lid hinge
into the interior of the vehicle.
♦ The clips for the Bowden cable
are pre-positioned and are inser‐
ted in the corresponding holes.
❑ Before removing, unclip
rear lid lock cover.
❑ First unclip from cable
support bracket on rear
lid lock, then detach
from operating lever.
2 - Rear lid trim
❑ Removed ⇒ General
stalling rear lid trim (bot‐
tom)
3 - Rear lid lock
4 - Cover
❑ Unclip at rear lid lock
5 - Operating lever for manual
release mechanism
❑ When installing, first at‐
tach Bowden cable to
operating lever, then
press into cable support
bracket on lid lock.
6 - Clip
❑ Pre-positioned on Bowden cable
Routing on body:
2. Rear lid 79
1 - Loop
❑ Fix in position under‐
neath rear seat bench
with adhesive tape
2 - Support bracket
❑ Not available as re‐
placement part
❑ Engage Bowden cable
in support bracket of
rear lid lock as shown.
3 - Rear lid lock
4 - Bowden cable
❑ Route from rear lid lock
via hinge into interior, as
shown
❑ Attached to rear lid
hinge; lock in position on
reverse side with tabs of
cover.
❑ Bowden cable must be
routed correctly in cover
⇒ page 44 .
5 - Clip
❑ The clips are pre-posi‐
tioned and must be clip‐
ped into the correspond‐
ing holes.

2.13 Removing and installing extension

spring
⇒ “2.13.1 Removing and installing extension spring - Saloon”,
page 81
2.13.1 Removing and installing extension spring - Saloon
1 - Gas strut
❑ Disengaging ⇒ page 65
❑ Only for manual rear lid
operation
2 - Rear lid hinge
3 - Ball-head pin
placement part
4 - Ball-head pin
❑ 21 Nm
5 - Cover
– Push onto coil section
from side.
– Slide cover forwards

and engage at hinge
pin.
6 - Spring
❑ Note correct direction of
attachment
Attachment points for spring
2. Rear lid 81
1 - Spring
Note
Note direction of attachment of

spring at hinge pins.
– On left side, engage

hook of spring (side with
short hook) first at hinge
from bottom to top.
– On right side, engage

hook of spring (side with
short hook) first at hinge
from top to bottom.
– Then engage spring

(side with long hook) on
body at attachment
point -b-.
2 - Rear lid hinge

3 - Cover
❑ When installing, slide
cover forwards; cover
must engage at hinge
pin.

3 Tank flap unit

⇒ “3.1 Exploded view - tank flap unit”, page 83
⇒ “3.2 Removing and installing tank flap unit”, page 85
3.1 Exploded view - tank flap unit

⇒ “3.1.1 Exploded view - tank flap unit”, page 83
⇒ “3.1.2 Exploded view - manual release for tank flap”,
page 84
⇒ “3.1.3 Exploded view - drain hose for tank flap unit”,
page 85
3.1.1 Exploded view - tank flap unit
1 - Drain hose
❑ When installing, make
sure that component is
routed correctly
⇒ page 85 .
2 - Cable for manual release
3 - Bolts
❑ 1.5 Nm
4 - Tank filler flap locking motor
- V 155-
⇒ page 141
5 - Lid for tank flap
⇒ page 87
6 - Tank flap unit
❑ Must be renewed follow‐
ing removal
⇒ page 85
3. Tank flap unit 83

3.1.2 Exploded view - manual release for tank flap

- V 155-
2 - Side panel
– Attach cable lug as indi‐
cated.

❑ Insert tank filler flap
locking motor - V 155-
with cable through tank
flap opening.
❑ Pull cable through to‐
wards rear into interior
and attach lug of cable
to flange on side panel.

3.1.3 Exploded view - drain hose for tank flap unit
1 - Tank flap
2 - Drain hose
– Route drain hose under
wheel housing liner, as
shown, and insert into
guide.
3 - Guide (rear)
❑ Drain hose inserted into
guide in bottom of
bumper, as shown.
4 - Adhesive tape
❑ When installing, secure
drain hose with adhe‐
sive tape, as shown.
3.2 Removing and installing tank flap unit

⇒ “3.2.1 Removing and installing tank flap unit”, page 85
⇒ “3.2.2 Removing and installing lid for tank flap”, page 87
3.2.1 Removing and installing tank flap unit

Removing
– Remove cover for luggage compartment side trim (right-side).
– Disengage handle for manual release cable and move clear.
– Pull drain hose out of guide on bumper ⇒ page 85 .
– Open tank flap.
– Remove filler cap for filler neck of fuel tank.

– Release tank flap unit at points indicated by -arrows-.
– To do so, insert a small screwdriver through marked locations

in tank flap unit from below at an angle and over catches (in
direction of arrows).
– Pull screwdriver upwards slightly to release catches behind.
– Take tank flap unit out of body opening and guide cable for
manual release through opening.
– Remove tank filler flap locking motor ⇒ page 141 .
Installing
Note
Tank flap unit must be renewed following removal.
– Guide manual release cable through opening to luggage com‐

partment.
– Insert tank flap at an angle until retaining tabs engage at flange
in side panel.
Installation position of tank flap unit

1 - Side panel
❑ Adjust distance -A- = 2.2
mm (even distance from
side panel).
3 - Tank flap
❑ Slide onto filler neck all
around (as shown).
4 - Filler neck
5 - Drain hose
❑ Route without kinking
6 - Wheel housing
3.2.2 Removing and installing lid for tank flap

Removing
– Insert a small screwdriver between tank flap -1- and lid -1- as
shown to release retainer.
– Pull flap slightly towards rear -arrow- out of retainer.
Installing
– Insert lid into recesses in tank flap.

– Push lid -2- forwards until retainer -arrows- on mounting of

tank flap -1- engages.

4 Charging flap unit

⇒ “4.1 Exploded view - charging flap unit”, page 89
⇒ “4.2 Removing and installing charging flap unit”, page 89
⇒ “4.3 Removing and installing charging flap unit trim”,
page 90
⇒ “4.4 Removing and installing manual release cable”,
page 91
4.1 Exploded view - charging flap unit
1 - Charging flap unit trim

⇒ page 90
2 - Charging flap unit
❑ Renew after removing
⇒ page 89
3 - Actuator for high-voltage
charging flap lock 1 - F496-
⇒ page 142
4 - Bolt
❑ 2x
❑ 1.5 Nm
5 - Cable
❑ For manual release
mechanism
⇒ page 91
6 - Module for battery charge
selector buttons - EX32-
❑ With LED module for
charging socket 1 -
L263- , immediate
charge button - E766-
and charge profile se‐
lector button - E808-
❑ Exploded view ⇒ En‐
gine; Rep. gr. 93 ;
Charging socket; Explo‐
ded view - charging
socket
7 - Warning label
❑ On charging flap unit
8 - Cap for charging socket
4.2 Removing and installing charging flap

unit
• The following components have to be renewed after removal
⇒ page 89 .
4. Charging flap unit 89

Removing
– Remove cover for luggage compartment side trim (right-side).
– Disengage handle for manual release cable and move clear.
– Open charging flap.
– Detach cap for charging socket.
– Release charging flap unit by pushing a small screwdriver
through marked locations -arrows-.
– Fastener (top): Position screwdriver above fastener -1- and

release fastener with screwdriver in direction of -arrow A-.
– Fastener (bottom): Position screwdriver below fastener -2-
and release fastener with screwdriver in direction of
-arrow B-.
– Close charging flap.
– Take charging flap unit out of body cut-out.

– Detach charging flap unit and guide manual release cable
-3- out.
Installing
– First insert charging flap unit in body cut-out on hinge side and
then press it in until it engages audibly.
– Check that collar is seated correctly in mounting for charging
socket.
4.3 Removing and installing charging flap

unit trim
Removing
– Open charging flap.

– Use a screwdriver to release retaining clip in recess between

trim panel -2- and charging flap -1-.
– Pull trim panel slightly off charging flap towards rear -arrow-
and detach.
Installing
• When fitting trim panel -2- onto charging flap -1-, guides on
trim panel must be applied behind mounting points -arrows-.
– Slide trim panel forwards until retaining clip engages audibly.
4.4 Removing and installing manual release

cable
Removing
– Remove actuator for high-voltage charging flap lock
⇒ page 142 .
– Thread cable -1- out of guide -4-.
– Disengage lug -3- at mounting -2- for manual release mecha‐
nism and pull it out of cable support bracket.
Installing
4. Charging flap unit 91

57 – Front doors, door components, central locking

1 Door
⇒ “1.1 Exploded view - door”, page 92
⇒ “1.2 Exploded view - door seals”, page 93
⇒ “1.3 Removing and installing door”, page 94
⇒ “1.4 Adjusting door”, page 95
⇒ “1.5 Adjusting striker”, page 99
⇒ “1.6 Removing and installing door arrester”, page 100
⇒ “1.7 Removing and installing inner door seal”, page 100
⇒ “1.8 Removing and installing outer door seal”, page 102
1.1 Exploded view - door
1 - Front door
2 - Bolt
❑ 8 Nm
3 - Gasket
❑ For door arrester
4 - Bolt
❑ 33 Nm
5 - Cap
6 - Door arrester
⇒ page 100
7 - Cap
❑ Fit onto stud
8 - Door hinge (top)
9 - Bolt
❑ 34 Nm
10 - Bolt
Note
♦ The bolt is a fitted bolt; therefore

it is usually not necessary to ad‐
just the door via this bolt.
♦ If it does become necessary to
make an adjustment via this bolt,
the bolt can be replaced with a
bolt of the same length and prop‐
erty class.
❑ 34 Nm
11 - Stud
❑ 23 Nm
92 Rep. gr.57 - Front doors, door components, central locking

12 - Bolt
❑ 34 Nm
13 - Bolt
❑ 34 Nm
14 - Door hinge (bottom)
1.2 Exploded view - door seals

⇒ “1.2.1 Exploded view - inner door seals”, page 93
⇒ “1.2.2 Exploded view - outer door seals”, page 94
1.2.1 Exploded view - inner door seals
1 - Inner door seal

⇒ page 100
2 - Door trim
3 - Body flange
1. Door 93
1.2.2 Exploded view - outer door seals
1 - Front door
2 - Door seal
⇒ page 102
1.3 Removing and installing door

Removing
– Unplug door disconnector at A-pillar ⇒ Electrical system; Rep.
gr. 97 ; Connectors .

– Unscrew bolt -2- for door arrester.

– Detach caps -1- and -3- from studs.
– Unscrew studs -4- from door hinge (top and bottom).
Caution
Risk of paintwork damage.

♦ Protect paintwork on door or side panel from damage.
– Carefully lift door off hinges.

Installing
Note
No adjustment has to be performed after the front door has been

installed.
Tightening torques
♦ ⇒ “1.1 Exploded view - door”, page 92
1.4 Adjusting door

1. Door 95
♦ Template - T40038 /14-
♦ On front door, use template - T40038 /14- with side -A- for front
measuring point on A-pillar and with side -B- for rear measur‐
ing point on B-pillar.
♦ The »min and max« markings are used to check the side ad‐
justment.
♦ The cut-out in the template is used to check the height.
♦ The 0.6 mm graduation at each end of the template is used to
check the underhang of the front door relative to the wing, and
of the rear door to the front door.
Checking adjustment of height with template - T40038 /14-
– Position template on roof.
– Template must make contact with roof and trim strip -1- at top,
as shown -arrow-.
– Height is correctly adjusted when bottom edge of window
guide -2- is within cut-out -bottom arrow- (a = 2 mm).

Checking lateral adjustment with template - T40038 /14-
Note
♦ The template is 200 mm long and can be used to measure the

required distance.
♦ Position template at this distance at measuring point -B-.
– Position template at distance -x1- = 200 mm at measuring

point -B-/measuring point -A- (front).
– If »min« adjustment is correct, template must make contact at
points -1- and -3-.
– A small gap is permissible at point -2- of template.
– If »max« adjustment is correct, template must make contact
at points -2- and -3-.
Gap widths
1. Door 97
Note
The sides of the gap must be parallel (variation not more than 0.5 mm).
♦ Dimension E = 3.5 mm
♦ Dimension F = 5.0 mm
♦ Dimension G = 4.5 mm
♦ Dimension H = 3.5 mm
Driver side:
– Remove dash panel cover (driver side) ⇒ General body re‐
pairs, interior; Rep. gr. 68 ; Storage compartments/covers/trim
panels; Removing and installing dash panel cover (driver
side) .
– Remove A-pillar trim (bottom) ⇒ General body repairs, interi‐
or; Rep. gr. 70 ; Passenger compartment trim panels; Re‐
moving and installing A-pillar trim .
– Remove mounting for relay carrier (driver side) ⇒ Electrical
system; Rep. gr. 97 ; Relay carriers, fuse carriers, electronics
boxes; Overview of fitting locations - relay carriers, fuse carri‐
ers, electronics boxes .
Passenger side:
– Remove glove box ⇒ General body repairs, interior; Rep. gr.
68 ; Storage compartments/covers/trim panels; Removing and
installing glove box .
Both sides:
– Remove connector point at A-pillar ⇒ Electrical system; Rep.
gr. 97 ; Connectors; Removing and installing connector point
at A-pillar (left-side) .

Longitudinal adjustment
– Unscrew bolts -arrows B- at top and bottom of hinge and on
A-pillar -item 1-.
– Adjust door -2- lengthwise.
– Tighten bolts -arrows B-.
Tightening torques
Adjusting the door inwards/outwards
Note
♦ Bolt -A- is a fitted bolt; therefore it is usually not necessary to

adjust the door via this bolt.
♦ If it does become necessary to make an adjustment via this
bolt, the bolt can be replaced with a bolt of the same length
and property class.
– Loosen bolts (top and bottom) -arrows A- at hinge.

– Tighten bolts -arrows A-.
Tightening torques
1.5 Adjusting striker
Note
♦ The striker shim plate with the pins -arrows- must be posi‐
tioned exactly in the hole.
♦ After adjusting the striker, the pins must be sheared off cleanly.
– Loosen bolts -2-.

– Move striker -1- until door is flush with body contour.
Note
♦ The striker is only to be used for adjustment towards the centre

of the vehicle.
♦ Do not adjust the height of the door via the striker; otherwise
the door lock will be damaged.
– If adjustment is correct, striker should engage centrally in door

lock.
– Tighten bolts -2-.
Tightening torques
♦ ⇒ “2.2.2 Exploded view - door lock and striker”, page 114
1. Door 99
1.6 Removing and installing door arrester

Removing
Note
Mask A-pillar in vicinity of door arrester with adhesive tape to

avoid damaging paintwork.
– Move door window to “closed” position.

– Remove door trim ⇒ General body repairs, interior; Rep. gr.
70 ; Door trim (front); Removing and installing door trim (front) .
– Remove lower loudspeaker ⇒ Communication; Rep. gr. 91 ;
Sound system; Overview of fitting locations - sound system .
– Unscrew bolt -arrow- for door arrester.
– Detach sealing piece -1- for door arrester from door opening.
– Unscrew bolts -arrows- and take out door arrester -2- inwards.
– Pull rubber sleeve -1- on door arrester to the side slightly

-arrows A-.
– Detach rubber sleeve from door arrester -2- -arrow B-.
Installing
Tightening torques
1.7 Removing and installing inner door seal

Removing and installing inner door seal

1 - Inner door seal

❑ B-pillar trim (top) re‐
moved
❑ A-pillar trim and B-pillar
trim (bottom) removed
❑ Fitted on body flange all
around
body flange.
❑ To install, press seal on‐
to body flange by hand,
starting in top corner of
B-pillar and pressing
seal on along roof.
2 - Door trim
3 - Body flange
1. Door 101
1.8 Removing and installing outer door seal

⇒ “1.8.1 Removing and installing outer door seal”, page 102
⇒ “1.8.2 Removing and installing door joint seal”, page 108
1.8.1 Removing and installing outer door seal
Note
♦ The complete outer door seal is bonded on and can only be

renewed.
♦ The vehicle and the outer door seal must be at room temper‐
ature.
♦ Bonding surfaces must be free of dust and grease (clean with
cleaning solution - D 009 401 04- ).
♦ Apply primer - D 355 205 A2- to bonding surfaces on body
using applicator - D 009 500 25- and allow to flash off.
♦ The water drain holes are positioned correctly when they are
on the underside of the door.
♦ There is an insert at the door seal which must be pulled off all
around after the seal has been fitted; it can be taken hold of at
the bottom centre of the door seal ⇒ page 107 .

♦ Roller - 3356-
♦ Adhesive strip remover - VAS 6349-

♦ Template - T40038 /8-
1 - Front door
2 - Outer door seal
Note
♦ Prior to removal, mark position of

seal on door e.g. with adhesive
tape.
♦ To prevent any residual adhe‐
sive from remaining on door, first
stretch seal lengthwise
⇒ page 106 and only then pull
seal off door.
❑ Removing
– Pull seal slightly off door
at top of window frame
and cut through with
scissors or similar (com‐
mercially available).
– Stretch seal lengthwise

and then gradually pull
off upwards
⇒ page 158 .
❑ Installing
– Bonding surfaces must
be free of dust and
grease. Clean bonding
surfaces with cleaning
solution - D 009 401
04- ; if necessary use
adhesive strip remover -
VAS 6349- to remove
any adhesive residue.
– Apply primer - D 355

205 A2- to bonding surface on body using applicator - D 009 500 25- and allow to flash off for at least
10 minutes.
Caution
If flash-off time exceeds
three hours, primer must
be applied again.
1. Door 103
– Detach door arrester from body ⇒ page 105 .
– Fasten outer door seal behind door arrester.
– Secure door arrester again.
Note
♦ Align marking on outer door seal

with top corner at B-pillar.
♦ Secure outer door seal to win‐
dow frame (top, front and rear)
with adhesive tape
⇒ page 107 .
♦ When pressing on outer door
seal, start in centre at bottom and
gradually continue towards front
and rear.
– Peel off protective film in area of underside of door.
– Press outer door seal onto underside of door in centre and continue outwards to both sides.
– Gradually pull protective film off further and press on outer door seal.
– Press on outer door seal upwards along A-pillar and B-pillar.
– Finally press on outer door seal at top along window frame.
Caution
When
♦ installing, do not
stretch or compress door
seal.
If♦the outer door seal is
stretched or compressed
on the underside, at the
A-pillar or at the B-pillar,
the seal could become
detached.
The
♦ outer door seal can
only be stretched or com‐
pressed in the area of the
window frame at the top
(in this area the seal is
secured in place by the
window frame cover).
– Press on base of outer door seal ⇒ page 107 using roller - 3356- .
– Take hold of loose end of seal insert at bottom centre of door seal and pull off all around, making sure
the sealing lip is positioned evenly.

Caution
To prevent the outer
door seal from becoming
detached or misaligned,
it is important that the
door is not closed for at
least two hours; the ve‐
hicle must be stationary
at room temperature.
Detaching door arrester

– Fasten seal behind door arrester and tighten bolt to specified
torque ⇒ Item 4 (page 92) .
Marking position of seal

– Mark position of outer door seal -1- on window frame with ad‐
hesive tape -2-.
– Mark position of outer door seal -1- in entire area for seal with
adhesive tape -2-, as shown.
1. Door 105
Detaching outer door seal
Note
By stretching the outer door seal lengthwise, the adhesive is sep‐

arated from the door and the seal can be detached from the
window frame without leaving any adhesive.
– Gradually stretch outer door seal lengthwise -arrow-, as

shown, and detach.
– Proceeding step-by-step, pull outer door seal off all around
door shell.
– Remove any residual adhesive with adhesive strip remover -
VAS 6349- .
Renewing outer door seal (on new door)
Note
When installing, seal must be pressed on in transition area of outer radius to straight section of door shell
contour, as shown in detail views -arrows-.
1 - Front door
2 - Outer door seal
❑ Position outer door seal
on underside of door
and, starting in centre,
press front edge onto
transition areas of radi‐
us -arrow-.
❑ When pressing on outer
door seal, start in centre
at bottom and gradually
continue towards front
and rear.
❑ Perform remaining in‐
stallation steps as de‐
scribed above.
– Press seal into place all
around door shell using
roller - 3356- .
– Take hold of loose end

of seal insert at bottom
centre of door seal and
pull off all around, mak‐
ing sure the sealing lip is
positioned evenly.

Removing seal insert

– After door seal has been installed, seal insert -2- must be
pulled off all around seal.
– This pulls out sealing lip -1-, which is then positioned evenly
and correctly on door (no gaps).
Pressing on outer door seal
1 - Front door
2 - Outer door seal
– When installing outer
door seal, first secure it
to top of window frame
with adhesive tape
-arrows-.
Caution
Only press on base of
outer door seal using
roller - 3356- .
– Fold outer door seal up‐

wards, as shown in de‐
tail view, and press base
on firmly all around us‐
ing roller - 3356- .
1. Door 107
1.8.2 Removing and installing door joint seal
1 - Door joint seal

– First unclip from side of
B-pillar (bottom) -3-,
then unfasten gradually
from front to rear
2 - Door
3 - Clip

2 Door components
⇒ “2.1 Exploded view - window regulator”, page 109
⇒ “2.2 Exploded view - door handle and door lock”, page 112
⇒ “2.3 Exploded view - window guides and window slot trim
strips”, page 116
⇒ “2.4 Removing and installing window regulator”, page 116
⇒ “2.5 Removing and installing window regulator motor”,
page 118
⇒ “2.6 Removing and installing door handle”, page 119
⇒ “2.7 Removing and installing mounting bracket”, page 123
⇒ “2.8 Removing and installing door lock”, page 124
⇒ “2.10 Removing and installing inner door cover”, page 127
⇒ “2.11 Removing and installing power latching motor”,
page 129
⇒ “2.12 Removing and installing window guide”, page 130
⇒ “2.13 Removing and installing outer window slot trim strip”,
page 131
2.1 Exploded view - window regulator

⇒ “2.1.1 Exploded view - window regulator”, page 109
⇒ “2.1.2 Exploded view - window regulator, window regulator mo‐
tor”, page 111
2.1.1 Exploded view - window regulator
2. Door components 109

1 - Front door
2 - Window regulator
Note
Note different version for vehicles

with insulating glass.
⇒ page 116
3 - Stud
4 - Door window
Note

⇒ page 315
5 - Window regulator motor
⇒ page 118
6 - Bolt
❑ 6 Nm
7 - Bolt
❑ 3.5 Nm
8 - Cap
9 - Nut
❑ 6 Nm

2.1.2 Exploded view - window regulator, window regulator motor
nector at door control
unit.
2 - Left window regulator motor

- V14-
⇒ page 118
3 - Threaded pin
5 - Bolt
❑ 3.5 Nm

2.2 Exploded view - door handle and door

lock
⇒ “2.2.1 Exploded view - exterior door handle and door lock”,
page 112
⇒ “2.2.2 Exploded view - door lock and striker”, page 114
⇒ “2.2.3 Exploded view - door handle and door lock, motor for
power latching system”, page 115
2.2.1 Exploded view - exterior door handle and door lock
1 - Exterior door handle

❑ Equipment version with
trim strip: removing and
installing ⇒ page 173
⇒ page 120
2 - Bolt
❑ 2.5 Nm
3 - Backing plate (front)
⇒ “2.6.3 Removing and
installing exterior door
handle”, page 120
4 - Backing plate (rear)
handle”, page 120
5 - Housing
❑ Instead of lock cylinder
❑ For passenger door
⇒ page 119
6 - Bolt
⇒ page 114
7 - Cap
❑ Prise off
8 - Door lock
9 - Bolt
❑ 1.5 Nm
10 - Guide
❑ For lock cylinder
11 - Mounting bracket
❑ Only remove and install together with door lock
12 - Retaining bracket
❑ For lock cylinder/housing
❑ With clamping bolt

13 - Bolt
❑ 2.5 Nm
14 - Operating cable
❑ For door lock
❑ Removing and installing ⇒ “2.8.2 Removing and installing operating cable for door lock”, page 125
15 - Lock cylinder
❑ For driver's door
16 - Magnet
❑ Only on vehicles with Keyless Entry system
– Insert magnet in cap.
– Fit cap on lock cylinder housing and insert into door.
– Screw in bolt -13- as far as stop.
17 - Cap
❑ Driver side: for lock cylinder
❑ Passenger side: closed design
❑ Equipment version with trim strip: removing and installing ⇒ page 173
18 - Trim for exterior door handle
❑ For vehicles without Keyless Entry system
19 - Contact sensor for exterior door handle
❑ Removing and installing ⇒ Electrical system; Rep. gr. 94 ; Entry and start authorisation; Removing and
installing front exterior door handle switches

2.2.2 Exploded view - door lock and striker
1 - Door lock
Caution
Risk of malfunction
To prevent the operating
cable from being kinked
or bent too much when it
is disengaged/engaged,
the door lock must be re‐
moved and installed to‐
gether with the mounting
bracket.
The operating cable
must be engaged in/dis‐
engaged from the oper‐
ating lever on the door
with the components re‐
moved from the vehicle.

⇒ page 124
2 - Bolt
❑ 25 Nm
3 - Striker
⇒ page 127
4 - Bolt
❑ 19 Nm
5 - Grommet
placement part
6 - Cable for interior door han‐
dle
7 - Cover for inner door panel
❑ Note different versions
8 - Grommet
❑ Cannot be renewed separately
9 - Bowden cable for power latching system
❑ Vehicles with power latching system only
❑ Supplied together with door lock

2.2.3 Exploded view - door handle and door lock, motor for power latching system
1 - Bowden cable
2 - Driver door power latching
motor - V302-
⇒ page 129
3 - Insulation
5 - Bolt
❑ 3.5 Nm

2.3 Exploded view - window guides and window slot trim strips
1 - Door
2 - Outer window slot trim strip
⇒ page 131
3 - Window guide
⇒ page 130
2.4 Removing and installing window regula‐

tor
Removing
– Remove window regulator motor ⇒ page 118 .
– Remove bass loudspeaker ⇒ Communication; Rep. gr. 91 ;
Sound system; Removing and installing front bass loudspeak‐
ers -R21- / -R23- .

– Remove nuts -2- and bolts -3- from trim -1-.

– Remove door window ⇒ page 315 .
– Using an 11 mm socket, release retaining clips -arrows- of

threaded pins -3- for window regulators (slide socket onto
threaded pins).
– Unclip cable -2- on inside of door from cable guide -1-.
– Remove sealing plugs -1- (top and bottom).
– Remove nuts -2- at top and loosen bolts -4- at bottom.

– Take window regulator out through opening in inner door panel
towards rear.
Installing
– Installation is carried out in reverse order; note the following:
When installing, clip cables into inner door panel and make sure
they are routed correctly.
Tightening torques
♦ ⇒ “2.1.1 Exploded view - window regulator”, page 109
♦ Trim to door: 3 Nm


tor motor
Removing
Note
The window regulator motor can be removed or installed with the

motor or door window in any position.

– Unplug electrical connector -1- from door control unit.
– Unscrew bolts -arrows- and detach window regulator motor
-2- from window regulator.
Installing
• Retaining clips -3- of threaded pins -2- for window regulator

must be engaged in inner door panel.
– Slide window regulator motor -1- onto threaded pins and tight‐
en bolts -4-.
Tightening torques

2.6 Removing and installing door handle

⇒ “2.6.1 Removing and installing lock cylinder”, page 119
⇒ “2.6.2 Removing and installing cap for lock cylinder”,
page 119
⇒ “2.6.3 Removing and installing exterior door handle”,
page 120
⇒ “2.6.4 Removing and installing trim for exterior door handle”,
page 121
⇒ “2.6.5 Removing and installing trim strips on door handle”, page
122
⇒ “2.6.6 Removing and installing lock cylinder guide”, page 122
2.6.1 Removing and installing lock cylinder

Removing
– Push outer door seal to side and detach cover over hole
-arrow A-.
– Unscrew clamping bolt -4- as far as possible using a screw‐
driver -1-.
– Push retainer -3- for lock cylinder inwards.
– Pull lock cylinder -2- out of mounting bracket -arrow B-.
Note
If the lock cylinder cannot be pulled out, insert the ignition key in
the lock cylinder and pull out the lock cylinder with the key turned
slightly.
Installing
– Push lock cylinder into mounting bracket and then check
whether the closing and opening positions for the door lock
are actuated.
Tightening torques
♦ ⇒ “2.2.1 Exploded view - exterior door handle and door lock”,
page 112
2.6.2 Removing and installing cap for lock cyl‐

inder
Removing
– Remove lock cylinder ⇒ page 119 .

– Pull apart retaining clips -arrows- and detach cap -2- from lock
cylinder -1-, using a small screwdriver if necessary.
Installing
Caution
On vehicles with Keyless Entry system, magnet must be press‐

ed into cap.
– Press on cap for lock cylinder until it engages audibly.
2.6.3 Removing and installing exterior door

handle
Removing
– Pull exterior door handle -1- in direction of -arrow-; exterior
door handle will be detached from operating lever in mounting
bracket.
– Swivel exterior door handle -1- outwards -arrow- and take out
of mounting on mounting bracket.
– On vehicles with Keyless Entry system, unplug electrical con‐
nector -2- from exterior door handle.
Installing
– Renew backing plates -1- and -2- for door handle if they are
damaged or brittle.

– Insert exterior door handle -1- -arrow A-, making sure that ex‐
terior door handle engages in mounting -2- on mounting brack‐
et -3-.
– Swivel exterior door handle -1- in direction of -arrow B- and
push in »driver« -5- in front of operating lever -4- in mounting
bracket.
– Press retainer for lock cylinder towards exterior door handle.
2.6.4 Removing and installing trim for exterior

door handle
On vehicles without Keyless Entry system, a trim is fitted instead
of the contact sensor for exterior door handle.
Removing
– Remove exterior door handle ⇒ page 120 .
– Prise out trim -2- for exterior door handle using an awl -1- at
point indicated in illustration -arrow-.
– Pull trim for exterior door handle out of exterior door handle
-3-.
Installing
– Push in trim for exterior door handle until it engages audibly.

2.6.5 Removing and installing trim strips on

door handle
Removing and installing trim strip on door handle ⇒ page 122
Removing and installing trim strip on cap ⇒ page 122
Removing and installing trim strip on door handle:
Removing
– Detach trim strip -4- from door handle -1- -arrow A-.
Installing
– Tighten bolt -5- to 0.2 Nm.
• Bolt head must not protrude above contact surface for trim
strip.
Removing and installing trim strip on cap:
Removing
– Remove cap ⇒ page 119 .
– Pull trim strip -3- off cap -2- -arrow B-.
Installing
2.6.6 Removing and installing lock cylinder

guide
Removing
– Close door window completely.
– Remove cover for inner door panel ⇒ page 127 .
– Remove bolt -4- and pull guide -2- with tab -3- out of door lock
-1-.
Installing
– Insert tab -3- properly into door lock (retaining hooks must en‐
gage completely).
– Tighten bolt -4- to specified torque ⇒ Item 9 (page 112) .

2.7 Removing and installing mounting

bracket
♦ Removal lever - 80-200-
Caution
Risk of malfunction
To prevent the operating cable from being kinked or bent too
much when it is disengaged/engaged, the mounting bracket
must be removed and installed together with the door lock.
Therefore the operating cable must be engaged in/disengaged
from the operating lever on the door lock with the components
removed from the vehicle.
Removing
– Remove lock cylinder guide ⇒ page 122 .
– Where fitted, disengage electrical wiring from mounting brack‐
et -arrow-.
– Move binding clip -1- of electrical wire clear with removal lever
- 80-200- .
Note
Use soap solution to aid removal if necessary.
– Unscrew bolt -3- and detach mounting bracket -2-.

– Remove bolts -arrows- from door lock.

– Slide mounting bracket with door lock -1- downwards and take
both components out of door.
– If mounting bracket is to be renewed, also remove the follow‐
ing components:
♦ Remove operating cable for door lock ⇒ page 125 .
Installing
Tightening torques
page 112
2.8 Removing and installing door lock

⇒ “2.8.1 Removing and installing door lock”, page 124
⇒ “2.8.2 Removing and installing operating cable for door lock”,
page 125
⇒ “2.8.3 Removing and installing operating cable for interior door
handle”, page 126
2.8.1 Removing and installing door lock
Caution
Risk of malfunction
much when it is disengaged/engaged, the door lock must be
removed and installed together with the mounting bracket.
Removing
et -arrow-.
- 80-200- .
Note


– If door lock is to be renewed, also remove the following com‐
ponents:
Installing
Tightening torques
page 112
2.8.2 Removing and installing operating cable

for door lock
Caution
Risk of malfunction
Removing
– Remove mounting bracket and door lock ⇒ page 124 .
– Turn operating cable on lever -2- 90° in direction of -arrow A-
and take it out of cable support bracket -1-.
– Turn operating cable on operating lever -3- for door lock in
direction of -arrow B-.
• The operating cable must be aligned with the opening on the
operating lever.
– Disengage operating cable from operating lever.

– Disengage operating cable -1- from operating lever by press‐

ing cable support bracket -3- out of mounting on mounting
bracket -2- -arrow-.
– Take out operating shaft.
Installing

for interior door handle
Caution
Risk of malfunction
♦ When removing and installing, make sure the operating
cable is not kinked or damaged.
Removing
– Remove inner door cover ⇒ page 127 .
– Remove bolts -arrows-.
– Press door lock -1- to the side.
– If necessary, unplug electrical connector -2-.
– Disengage operating cable -3- from door lock support bracket

-2- -arrow A-.
– Turn nipple -1- 90° in direction of -arrow B- and take it out of
door opener release lever -4-.
Installing

– Insert nipple -2- in door opener release lever -3-

-bottom arrow-.
– Turn nipple 90° -top arrow- and press operating cable into ca‐
ble support bracket on door lock -1- until it engages audibly.
Tightening torques

Removing
– Unscrew bolts -2- and detach striker -1-.
Installing
– Adjust striker ⇒ “1.4 Adjusting door”, page 95 .
Tightening torques
2.10 Removing and installing inner door cov‐

er
Note
The illustration shows the cover for vehicles with power latching
system, and additionally it shows fasteners that must be released
prior to removal.

1 - Cover
– Remove door trim ⇒
Door trim (front); Re‐
door trim (front) .
Vehicles without power latch‐

ing system
– Pull electrical wiring out

of retaining clips -5-.
– When removing cover, it

is important to start at
the top.
Vehicles with power latching

system
– Disconnect power sup‐

ply to power latching
motor.
– Release fasteners (5x)

-arrows- by turning them
to the left and pull cover
out of inner door panel.
2 - Grommet with Bowden ca‐

ble
Caution
Do not kink Bowden ca‐
bles when installing.

sure it is seated correct‐
ly.
3 - Bowden cable for interior door handle
4 - Fastener (5x)
– To remove cover, release fasteners by turning them to the left.
– Must engage audibly during installation

2.11 Removing and installing power latching motor
1 - Bowden cable
2 - Driver door power latching
motor - V302-
❑ Removing
door trim (front) .

nector for motor.
– Unscrew bolts at motor.
– Guide Bowden cable

out of cable reel.
❑ Installing
– To install, first insert nip‐
ple of cable into cable
reel.
– Insert cable into groove

on cable reel through
360°, as shown in detail
view.
– Clip Bowden cable into

motor at side -arrows-.
– Secure motor by tight‐

ening bolts to specified
torque.
3 - Insulation
5 - Bolt
❑ 3.5 Nm

2.12 Removing and installing window guide
1 - Window guide
❑ Removing
– Exterior mirror removed
⇒ page 397
– Door trim and window

frame trim removed ⇒
window frame trim .
– Trim strip for door re‐
moved ⇒ page 349
– Trim panel for B-pillar

removed ⇒ page 342
– Door window removed

⇒ page 315
– Disengage window
guide from flange at un‐
derside of window frame
and detach downwards.
– Detach sealing strip

(self-adhesive) for win‐
dow guide at B-pillar.
– Pull window guide out of

trim panel for B-pillar to‐
wards rear and unclip at
C-pillar (4x).
– Detach inner window

slot trim strip upwards
from door flange.
– Detach window guide at B-pillar and C-pillar from door.
– Lift window guide out of door.

❑ Installing
– To facilitate assembly, coat window guide with soap solution.
– Position window guide at B-pillar (top) and slide it forwards into guide with clip ⇒ page 131 .
– Moulded section should touch door at rear (longitudinal direction).
– Press window guide onto sides of window frame towards rear and clip onto C-pillar.
– Install trim panels for B-pillar and C-pillar and insert window guide from side.
– Press on inner window slot trim strip.
Caution
Bonding surface must be
free of dust and grease.
– Clean bonding surface on door with cleaning solution - D 009 401 04- .

– Bond sealing strip for window guide onto door at B-pillar using double-sided adhesive tape.
2 - Trim panel for B-pillar
Inserting guide moulding

– Guide moulding -1- with clip -2- must be inserted at B-pillar
(top) -arrow-, as shown.
2.13 Removing and installing outer window

slot trim strip
♦ Removal tool - T40219-
Preparing removal tool - T40219- :

• Before removing window slot trim strip, carefully bend removal
tool - T40219- at the point indicated -arrow- so that removal
tool can be applied behind retaining strip.
Removing
– Lower door window.
– Remove window frame trim ⇒ General body repairs, interior;
Rep. gr. 70 ; Door trim (front); Removing and installing window
frame trim .
– Remove mounting for mirror adjustment unit ⇒ page 398 .
– Pull window guide in area of B-pillar out of guide.

– Insert removal tool - T40219- next to guide -4- for window slot
trim strip -3- and apply at retaining strip -2-.
• Front section -1- of removal tool - T40219- must be positioned
as shown in illustration.
– Press removal tool - T40219- lightly in direction of -arrow- to
release component.
• You should hear the retaining strip disengage.
– Carefully pull window slot trim strip upwards off door flange
using removal tool - T40219- .
– Pull moulded section -3- of window slot trim strip off door shell.
– Slide window slot trim strip -1- towards rear of vehicle
-arrow- until guide -2- for moulded section becomes disen‐
gaged at trim panel for B-pillar.
– Detach window slot trim strip.
Installing
Note
For installing, you can coat the bottom edge of the window slot
trim strip with tyre assembly paste.
– Position window slot trim strip -1- at trim panel for B-pillar on
door seam, as shown in illustration.
– Slide window slot trim strip forwards (as seen in direction of
travel) -arrow A-; guide -7- for moulded section -2- must be
inserted at B-pillar mounting -arrow B-.
– Insert rubber lug -4- in guide at trim panel for B-pillar -item 3-
and press retaining lugs -5- and -6- completely onto door shell.

– Press window slot trim strip -1- on evenly -arrows A-; retaining
strip -2- should engage audibly.
• When fixing strip in position -arrow-, retaining strip should en‐
gage underneath retaining plate -3-.
– Install window guide ⇒ page 130 .

3 Central locking system

⇒ “3.1 Overview of fitting locations - central locking system”, page
134
⇒ “3.2 Removing and installing driver door control unit J386 and
front passenger door control unit J387 ”, page 136
⇒ “3.3 Removing and installing rear left door control unit J388 and
rear right door control unit J389 ”, page 137
⇒ “3.4 Removing and installing convenience system central con‐
trol unit J393 ”, page 137
⇒ “3.5 Removing and installing interface control unit for vehicle
location system J843 ”, page 141
⇒ “3.6 Removing and installing bonnet contact switch F266 ”,
page 141
⇒ “3.7 Removing and installing tank filler flap locking motor V155
”, page 141
⇒ “3.8 Removing and installing actuator for high-voltage charging
flap lock 1 F496 ”, page 142
3.1 Overview of fitting locations - central

locking system
⇒ “3.1.1 Overview of fitting locations - central locking system, Sa‐
loon”, page 134
⇒ “3.1.2 Overview of fitting locations - central locking system,
Avant”, page 136
3.1.1 Overview of fitting locations - central locking system, Saloon

1 - Front passenger door con‐

trol unit - J387-
⇒ page 136
2 - Anti-theft alarm sensor -
G578-
3 - Rear right door control unit
- J389-
⇒ page 137
4 - Convenience system cen‐
tral control unit - J393-
⇒ page 137
- V 155-
⇒ page 141
❑ Procedures for remov‐
ing and installing as for
motor 2 for rear lid -
V445-
7 - Interface control unit for ve‐
hicle location system - J843-
⇒ page 141
8 - Power latching motor for
rear lid - V382-
⇒ page 67
10 - Control unit/actuator
Rear lid control unit - J605-
Actuator for high-voltage charging flap lock 1 - F496-
11 - Rear left door control unit - J388-
12 - Driver door control unit - J386-
13 - Bonnet contact switch - F266-
3. Central locking system 135

3.1.2 Overview of fitting locations - central locking system, Avant
1 - Front passenger door con‐

trol unit - J387-
⇒ page 136
2 - Anti-theft alarm sensor -
G578-
3 - Rear right door control unit
- J389-
⇒ page 137
4 - Convenience system cen‐
tral control unit - J393-
⇒ page 139
- V 155-
⇒ page 141
6 - Interface control unit for ve‐
hicle location system - J843-
⇒ page 141
⇒ page 69
8 - Rear lid control unit - J605-
⇒ page 73
9 - Power latching motor for
rear lid - V382-
⇒ page 67
❑ Procedures for removing and installing as for motor 2 for rear lid - V445-
11 - Rear left door control unit - J388-
12 - Driver door control unit - J386-
13 - Bonnet contact switch - F266-
3.2 Removing and installing driver door con‐

trol unit - J386- and front passenger door
control unit - J387-
Removing

– Unplug electrical connectors; to do so, pull locking element

and press release mechanism downwards.
– Move electrical connector clear at door control unit -1-.
– Press retaining catch -arrow- and disengage door control unit
-1- from door shell.
Installing
– Install in reverse order of removal; make sure retainer engag‐
es in inner door panel.
3.3 Removing and installing rear left door

control unit - J388- and rear right door
Removing
– Unplug electrical connectors; to do so, pull locking element
and press release mechanism downwards.
– Press retainer in direction of -arrow- and disengage door con‐

trol unit -1- from door shell.
Installing
– Install in reverse order of removal; make sure retainer engag‐
es in inner door panel.
3.4 Removing and installing convenience

system central control unit - J393-
⇒ “3.4.1 Removing and installing convenience system central
control unit J393 - Saloon”, page 137
⇒ “3.4.2 Removing and installing convenience system central
control unit J393 - Avant”, page 139
⇒ “3.4.3 Removing and installing retaining frame for convenience
system central control unit J393 - Avant”, page 140
3.4.1 Removing and installing convenience

system central control unit - J393- - Sa‐
loon
– If control unit is renewed, select “Replacement” function for
appropriate control unit in “Guided Fault Finding” or “Guided
Functions” ⇒ Vehicle diagnostic tester.
Removing
– Remove luggage compartment side trim (right-side) ⇒ Gen‐
eral body repairs, interior; Rep. gr. 70 ; Luggage compartment
trim panels; Removing and installing luggage compartment
side trim .

– Unfasten cable tie -4- and push wiring harness slightly to the
side.
– Unscrew nuts -2 and 3- and disengage retaining frame -1- with
central control unit from retaining pin -arrow-.
– Turn over retaining plate with central control unit.

– Release retaining tabs -3- -arrows A- and take convenience
system central control unit - J393- -item 2- out of retaining
frame -1- -arrow B-.

– Carefully remove fuse -6- and unplug aerial connector -7-.
– Unplug electrical connectors -2, 4, 5-.

– To unplug electrical connector, press catch -1-, turn retainer

in direction of -arrow- and unplug connector.
Installing
– Install retaining frame ⇒ Electrical system; Rep. gr. 97 ; Relay
carriers, fuse carriers, electronics boxes; Overview of fitting
locations - relay carriers, fuse carriers, electronics boxes .
3.4.2 Removing and installing convenience

system central control unit - J393- -
Avant
– If control unit is renewed, select “Replacement” function for
appropriate control unit in “Guided Fault Finding” or “Guided
Functions” ⇒ Vehicle diagnostic tester.
Removing
– Remove luggage compartment side trim (right-side) ⇒ Gen‐
eral body repairs, interior; Rep. gr. 70 ; Luggage compartment
trim panels; Removing and installing luggage compartment
side trim .
– Detach bracket for backrest remote release lever -1-.
– Release retaining tabs -3- -arrows A- and take convenience

system central control unit - J393- -item 2- out of retaining
frame -1- -arrow B-.


– Carefully remove fuse -6- and unplug aerial connector -7-.
– Unplug electrical connectors -2, 4, 5-.
– To unplug electrical connector, press catch -1-, turn retainer

in direction of -arrow- and unplug connector.
Installing
– Install bracket for backrest remote release lever ⇒ General
body repairs, interior; Rep. gr. 72 ; Rear seats; Exploded view
- locking mechanism .
3.4.3 Removing and installing retaining frame

for convenience system central control
unit - J393- - Avant
Removing
– Remove convenience system central control unit
⇒ page 139 .
– Release securing tab -3- -arrow A-, swivel retaining frame
-2- slightly forwards -arrow B- and guide it out of body -1-.
Installing

3.5 Removing and installing interface con‐

trol unit for vehicle location system -
J843-
Removing
– Open cover for luggage compartment trim (right-side).
– Unplug electrical connector to control unit -1-.
– Release locking element -arrow- on bracket and pull out con‐
trol unit.
Installing
3.6 Removing and installing bonnet contact

switch - F266-
Removing
– Remove bonnet lock ⇒ page 25 .
– Lift retaining tab -2- -arrow A-.
– Disengage contact switch -F266- -item 1- at bonnet lock -4-
-arrow B- and detach contact switch.
Installing
• Centring pins -3- on contact switch -F266- must be inserted
correctly in bonnet lock.
3.7 Removing and installing tank filler flap locking motor - V155-

1 - Drain hose
3 - Bolt
❑ 1.5 Nm
- V 155-
❑ Removing
– Fuel tank flap removed
⇒ page 85
– Remove bolts -3- at tank

filler flap locking motor -
V 155- .

nector and detach tank
V 155- .
❑ Installing
– Bolt together tank flap
and tank filler flap lock‐
ing motor - V 155- with
bolt -3-.
– Insert drain hose and

manual release cable
through opening in side
panel.
– Insert tank flap with tank

V 155- in opening for
tank flap at an angle and
press in until fasteners engage in flange in side panel.
– Make sure drain hose ⇒ page 85 and manual release cable ⇒ page 84 are routed correctly.

6 - Tank flap unit
❑ Must be renewed following removal.
3.8 Removing and installing actuator for

high-voltage charging flap lock 1 - F496-
Removing
– Remove charging flap unit ⇒ page 89 .


– Detach actuator for high-voltage charging flap lock -1- with
manual release cable from charging flap insert -2-.
– If renewing actuator for high-voltage charging flap lock, re‐
move manual release cable ⇒ page 91 .
Installing
Tightening torques
♦ ⇒ “4.1 Exploded view - charging flap unit”, page 89

58 – Rear doors, door components

1 Door
⇒ “1.1 Exploded view - door”, page 144
⇒ “1.2 Exploded view - door seals”, page 145
⇒ “1.3 Removing and installing door”, page 146
⇒ “1.4 Adjusting door”, page 147
⇒ “1.5 Adjusting striker”, page 152
⇒ “1.6 Removing and installing door arrester”, page 152
⇒ “1.7 Removing and installing inner door seal”, page 153
⇒ “1.8 Removing and installing outer door seal”, page 155
1.1 Exploded view - door
1 - Rear door
2 - Bolt
❑ 8 Nm
3 - Gasket
4 - Bolt
❑ 33 Nm
5 - Cap
6 - Door arrester
⇒ page 152
7 - Cap
❑ Fit onto stud
8 - Door hinge (top)
9 - Bolt
Note
♦ The bolt is a fitted bolt; therefore

it is usually not necessary to ad‐
just the door via this bolt.
♦ If it does become necessary to
make an adjustment via this bolt,
the bolt can be replaced with a
bolt of the same length and prop‐
erty class.
❑ 34 Nm
10 - Stud
❑ 23 Nm
11 - Nut
❑ 34 Nm
144 Rep. gr.58 - Rear doors, door components

12 - Bolt
❑ 34 Nm
13 - Bolt
❑ 34 Nm
14 - Door hinge (bottom)
1.2 Exploded view - door seals

⇒ “1.2.1 Exploded view - inner door seals”, page 145
⇒ “1.2.2 Exploded view - outer door seals”, page 146
1.2.1 Exploded view - inner door seals
1 - Inner door seal (bottom)

⇒ page 153
2 - Body flange
3 - Door
1. Door 145
1.2.2 Exploded view - outer door seals
1 - Rear door
2 - Outer door seal
⇒ page 155
1.3 Removing and installing door

Removing
– Unplug electrical connector at A-pillar ⇒ Electrical system;
Rep. gr. 97 ; Connectors .

– Unscrew bolt -2- for door arrester.

– Detach caps -1- and -3- from studs.
– Unscrew studs -4- from door hinge (top and bottom).
Caution
♦ Protect paintwork on door or side panel from damage.
– Carefully lift door off hinges.

Installing
Note
No adjustment has to be performed after the front door has been

installed.
1.4 Adjusting door

♦ Template - T40038 /14- (and additionally template - T40038 /

15- for Avant models)
♦ On rear door of Saloon, use template - T40038 /14- with side

-B- for front measuring point on B-pillar and with side -A- for
rear measuring point on C-pillar.
1. Door 147
♦ The »min and max« markings are used to check the side ad‐
justment.
♦ The cut-out in the template is used to check the height.
♦ The 0.6 mm graduation at each end of the template is used to
check the underhang of the front door relative to the wing, and
of the rear door to the front door.
Note
Use template - T40038 /15- on Avant models for adjusting rear

measuring point on C-pillar.
Checking adjustment of height with template - T40038 /14-

– Position template on roof at measuring points -A- / -B-.
Note
Use template - T40038 /15- on Avant models for measuring point

on C-pillar.
– Template must make contact with roof and trim strip -1- at top,
as shown -arrow-.
– Height is correctly adjusted when bottom edge of window
guide -2- is within cut-out -bottom arrow- (-a- = 2 mm).

Checking lateral adjustment with template - T40038 /14-
Note
♦ There is a 150 mm groove in the template (from B-side) which

can be used to measure the required distance.
♦ Position template at this distance (at measuring point -B-), as
shown.
– Position template at distance -x2- = 150 mm at measuring

point -B-/measuring point -A- (rear).
– If »min« adjustment is correct, template must make contact at
points -1- and -3-.
– If »max« adjustment is correct, template must make contact
at points -2- and -3-.
Note
Use template - T40038 /15- on Avant models for measuring point

on C-pillar.
Gap widths - Saloon
1. Door 149
Note
♦ All dimensions are given in »mm«.

♦ All tolerance ranges for the dimensions are ± 0.5 mm.
♦ The sides of the gap must be parallel (variation not more than 0.5 mm).
Gap widths - Avant

Note
♦ All dimensions are given in »mm«.

♦ All tolerance ranges for the dimensions are ± 0.5 mm.
♦ The sides of the gap must be parallel (variation not more than 0.5 mm).
– Remove B-pillar trim ⇒ General body repairs, interior; Rep.
gr. 70 ; Passenger compartment trim panels; Removing and
installing B-pillar trim .
1. Door 151
Longitudinal adjustment
– Unscrew bolts -arrows B- at top and bottom of hinge and on
A-pillar -item 1-.
– Tighten bolts -arrows B-.
Tightening torques
Height adjustment
Note
♦ The hinge bolts on the door are fitted bolts; therefore it is usu‐
ally not necessary to adjust the door via these bolts.
♦ If it does become necessary to make an adjustment via these
bolts, the bolts can be replaced with bolts of the same length
and property class.
1.5 Adjusting striker

Procedure
Note
♦ The striker is only to be used for adjustment towards the centre

of the vehicle.
♦ Do not adjust the height of the door via the striker; otherwise
the door lock will be damaged.
– Loosen bolts -2-.

– Move striker -1- until door is flush with body contour.
– If adjustment is correct, striker should engage centrally in door
lock.
– Tighten bolts -2-.
Tightening torques
♦ ⇒ “2.2.2 Exploded view - door handle and door lock, operating
cable”, page 166
1.6 Removing and installing door arrester

Removing
– Move door window to “closed” position.
70 ; Door trim (rear); Removing and installing door trim (rear) .

– Remove loudspeaker (bottom) ⇒ Communication; Rep. gr.

91 ; Sound system; Removing and installing rear bass loud‐
speakers -R15- / -R17- .
– Detach sealing piece -1- for door arrester from door opening.
– Unscrew bolts -arrows- and take out door arrester -2- inwards.
– Pull rubber sleeve -1- on door arrester to the side slightly

-arrows A-.
– Detach rubber sleeve from door arrester -2- -arrow B-.
Installing
Tightening torques
1.7 Removing and installing inner door seal
1. Door 153
1 - Inner door seal (bottom)

❑ Fitted on body flange all
around
body flange.
❑ When installing, unfas‐
ten B-pillar trim, C-pillar
trim, sill panel trim and
headliner in area of door
seal.
❑ When installing, align
seal at B-pillar (top) and,
starting at this point,
press seal onto body
flange by hand.
2 - Body flange
3 - Door

1.8 Removing and installing outer door seal

⇒ “1.8.1 Removing and installing outer door seal”, page 155
⇒ “1.8.2 Removing and installing door joint seal”, page 161
1.8.1 Removing and installing outer door seal
Note
♦ The complete outer door seal is bonded on and can only be

renewed.
♦ The vehicle and the outer door seal must be at room temper‐
ature.
cleaning solution - D 009 401 04- ).
♦ Apply primer - D 355 205 A2- to bonding surfaces using ap‐
plicator - D 009 500 25- and allow to flash off.
♦ The water drain holes are positioned correctly when they are
on the underside of the door.
♦ There is an insert at the door seal which must be pulled off all
around after the seal has been fitted; it can be taken hold of at
the bottom centre of the door seal ⇒ page 159 .

♦ Roller - 3356-
♦ Adhesive strip remover - VAS 6349-
1. Door 155
♦ Template - T40038 /8-
1 - Rear door
2 - Outer door seal
Note
♦ Prior to removal, mark position of

seal on door e.g. with adhesive
tape.
♦ To prevent any residual adhe‐
sive from remaining on door, first
stretch seal lengthwise
⇒ page 158 and only then pull
seal off door.
❑ Removing
– Pull seal slightly off door
at top of window frame
and cut through with
scissors or similar (com‐
mercially available).
– Stretch seal lengthwise

and then gradually pull
off upwards
⇒ page 158 .
❑ Installing
– Clean bonding surface
with cleaning solution -
D 009 401 04- ; if nec‐
essary use adhesive
strip remover - VAS
6349- to remove any ad‐
hesive residue.
– Apply primer - D 355

205 A2- to bonding sur‐
face on body using ap‐
plicator - D 009 500 25- and allow to flash off for at least 10 minutes.
Caution
If flash-off time exceeds
three hours, primer must
be applied again.
– Detach door arrester from body ⇒ page 152 .

– Fasten outer door seal behind door arrester.
– Secure door arrester again.
– Secure outer door seal to window frame (top left and right) in correct position with adhesive tape
⇒ Item 2 (page 107) .
– When positioned correctly, the water drain holes (2x) in the outer door seal are located on the underside
of the door.
Note
♦ Align marking on outer door seal

with top corner at B-pillar.
♦ When pressing on outer door
seal, start in centre at bottom and
gradually continue towards front
and rear.
– Peel off protective film in area of underside of door.
– Press outer door seal onto underside of door in centre and continue outwards to both sides.
– Gradually peel protective film off further on both sides and press on outer door seal.
– Press on outer door seal upwards along B-pillar and C-pillar.
– Finally press on outer door seal at top along window frame.
Caution
When
♦ installing, do not
stretch or compress door
seal.
If♦the outer door seal is
stretched or compressed
on the underside, at the
A-pillar or at the B-pillar,
the seal could become
detached.
The
♦ outer door seal can
only be stretched or com‐
pressed in the area of the
window frame at the top
(in this area the seal is
secured in place by the
window frame cover).
– Press on base of outer door seal ⇒ page 159 using roller - 3356- .
– Take hold of loose end of seal insert at bottom centre of door seal and pull off all around, making sure
the sealing lip is positioned evenly.
Caution
To prevent the outer
door seal from becoming
detached or misaligned,
it is important that the
door is not closed for at
least two hours; the ve‐
hicle must be stationary
at room temperature.
1. Door 157
Detaching door arrester

– Fasten seal behind door arrester and tighten bolt to specified
torque ⇒ Item 4 (page 144) .
Marking position of seal

– Mark position of outer door seal -1- on window frame with ad‐
hesive tape -2-.
– Mark position of outer door seal -1- in entire area for seal with
adhesive tape -2-, as shown.
Detaching outer door seal
Note
By stretching the outer door seal lengthwise, the adhesive is sep‐

arated from the door and the seal can be detached from the
window frame without leaving any adhesive.
– Gradually stretch outer door seal lengthwise -arrow-, as

shown, and detach.
– Proceeding step-by-step, pull outer door seal off all around
door shell.
– Remove any adhesive residue from window frame with adhe‐
sive strip remover - VAS 6349- .

Outer door seal on new door
Note
When installing, seal must be pressed on in transition area of inner/outer radius of door shell contour, as shown
in detail views -arrows-.
1 - Rear door
2 - Outer door seal
❑ Position outer door seal
on underside of door
and, starting in centre,
press front edge onto
transition areas of radi‐
us -arrow-.
❑ When pressing on outer
door seal, start in centre
at bottom and gradually
continue towards front
and rear.
❑ Perform remaining in‐
stallation steps as de‐
scribed above.
– Press base of seal firmly

into place all around
door shell using roller -
3356- .
– Take hold of loose end

of seal insert at bottom
centre of door seal and
pull off all around, mak‐
ing sure the sealing lip is
positioned evenly.
Removing seal insert

– After door seal has been installed, seal insert -2- must be
pulled off all around seal.
– This pulls out sealing lip -1-, which is then positioned evenly
and correctly on door (no gaps).
Pressing on outer door seal
1. Door 159
1 - Front door
2 - Outer door seal
– When installing outer
door seal, first secure it
to top of window frame
with adhesive tape
-arrows-.
Caution
Only press on base of
outer door seal using
roller - 3356- .
– Fold outer door seal up‐

wards, as shown in de‐
tail view, and press base
on firmly all around us‐

1.8.2 Removing and installing door joint seal
1 - Door joint seal

❑ Removing
– Pull out of window guide
at C-pillar downwards
(pull out of moulded sec‐
tion).
– Unclip downwards
along C-pillar and on un‐
derside of door.
– At B-pillar (top) unclip

towards front first.
– Detach door joint seal

downwards from door
flange.
2 - Rear door
3 - B-pillar
1. Door 161
2 Door components
⇒ “2.1 Exploded view - window regulator”, page 162
⇒ “2.2 Exploded view - door handle and door lock”, page 165
⇒ “2.3 Exploded view - window guides and window slot trim
strips”, page 168
⇒ “2.4 Removing and installing window regulator”, page 168
⇒ “2.5 Removing and installing window regulator motor”,
page 169
⇒ “2.6 Removing and installing door handle”, page 171
⇒ “2.7 Removing and installing mounting bracket”, page 174
⇒ “2.8 Removing and installing door lock”, page 175
⇒ “2.10 Removing and installing inner door cover”, page 178
⇒ “2.11 Removing and installing power latching motor V329 ”,
page 180
⇒ “2.12 Removing and installing window guide”, page 181
⇒ “2.13 Removing and installing window slot trim strip”,
page 182
2.1 Exploded view - window regulator

⇒ “2.1.1 Exploded view - window regulator”, page 162
⇒ “2.1.2 Exploded view - window regulator, window regulator mo‐
tor”, page 164
2.1.1 Exploded view - window regulator

1 - Rear door
Note

⇒ page 168
3 - Door window
Note

⇒ page 315
4 - Stud
5 - Cap
6 - Nut
❑ 6 Nm
7 - Rear left window regulator
motor - V26-
⇒ page 169
8 - Bolt
❑ 3x
❑ 3.5 Nm
9 - Nut
❑ 6 Nm

2.1.2 Exploded view - window regulator, window regulator motor
nector at window regu‐
lator motor.

motor - V26-
⇒ page 169
3 - Threaded pin
5 - Bolt

2.2 Exploded view - door handle and door

lock
⇒ “2.2.1 Exploded view - door handle and door lock”, page 165
⇒ “2.2.2 Exploded view - door handle and door lock, operating
cable”, page 166
⇒ “2.2.3 Exploded view - door handle and door lock, motor for
power latching system”, page 167
2.2.1 Exploded view - door handle and door lock
1 - Exterior door handle

❑ Equipment version with
trim strip: removing and
installing ⇒ page 173
⇒ page 120
2 - Bolt
❑ 2.5 Nm
3 - Backing plate (front)
handle”, page 120
4 - Backing plate (rear)
handle”, page 120
5 - Bolt
⇒ page 166
6 - Cap
❑ Prise off
7 - Door lock
❑ Before removing, door
lock must be removed
⇒ page 123
❑ For lock cylinder/hous‐
ing
❑ With clamping bolt
10 - Bolt
❑ Supplied with retainer
❑ 2.5 Nm
11 - Operating cable
❑ For door lock
12 - Housing

13 - Magnet
❑ Only on vehicles with Keyless Entry system
– Insert magnet in cap.
– Fit cap on lock cylinder housing and insert into door.
– Screw in bolt -10- as far as stop.
14 - Cap
❑ Equipment version with trim strip: removing and installing ⇒ page 173
15 - Trim for exterior door handle
16 - Contact sensor for exterior door handle
❑ For vehicles with Keyless Entry system
❑ Removing and installing ⇒ Electrical system; Rep. gr. 94 ; Entry and start authorisation; Removing and
installing rear exterior door handle switches
2.2.2 Exploded view - door handle and door lock, operating cable
1 - Door lock
⇒ page 175
2 - Bolt
❑ 25 Nm
3 - Striker
⇒ page 178
4 - Bolt
❑ 19 Nm
5 - Grommet
placement part
6 - Cable for interior door han‐
dle
⇒ page 177
❑ Note different versions
⇒ page 178
8 - Grommet
placement part
9 - Bowden cable for power
latching system
❑ Vehicles with power
latching system only
❑ Supplied together with
door lock

2.2.3 Exploded view - door handle and door lock, motor for power latching system
1 - Rear left power latching mo‐

tor - V307-
⇒ page 180
2 - Bowden cable
4 - Bolt
❑ 3 Nm

2.3 Exploded view - window guides and window slot trim strips
1 - Door
2 - Window slot trim strip
⇒ page 182
3 - Window guide
⇒ page 181

tor
Removing
– Remove door window ⇒ page 315 .
– Remove window regulator motor ⇒ page 118 .

– Use an 11 mm socket or similar to release retaining clips

-arrows- of threaded pins -1- for window regulators (slide sock‐
et over threaded pins).
– Prise out sealing plug -1-.

– Only loosen nut -2- at top and remove nut -4- at bottom while
at the same time counterholding threaded pin -2- for adjusting
door window.
– Take window regulator -3- out of opening in inner door panel
towards rear.
Installing
– Retaining clips -arrows- of threaded pins -1- for window regu‐

lator must be engaged in inner door panel.
Tightening torques
2.5 Removing and installing window regulator motor

nector at window regu‐
lator motor.

motor - V26-
Note
The window regulator motor can be

removed or installed with the motor
or door window in any position.
❑ Removing:
Door trim (rear); Re‐
door trim (rear) .
– Unscrew bolts -6- and

detach window regula‐
tor motor from window
regulator.
❑ Installing
• Tightening torque
⇒ page 109
Installation is carried out in re‐
verse order; note the following:
• Retaining clips -arrow- of

threaded pins for window
regulator must be engaged
in inner door panel.
– Slide window regulator
motor onto threaded pins and tighten bolts -6-.
Note
♦ With the window regulator

switches connected, switch on
the ignition and raise the door
windows as far as they will go.
♦ Keep the window regulator
switches pulled for approx. an‐
other 2 seconds to activate the
basic setting and the one-touch
open/close function.
3 - Threaded pin
5 - Bolt

2.6 Removing and installing door handle

⇒ “2.6.1 Removing and installing housing”, page 171
⇒ “2.6.2 Removing and installing cap for housing”, page 171
⇒ “2.6.3 Removing and installing exterior door handle”,
page 171
⇒ “2.6.4 Removing and installing trim for exterior door handle”,
page 173
⇒ “2.6.5 Removing and installing trim strips on door handle”, page
173
2.6.1 Removing and installing housing

Removing
– Push outer door seal to side and peel off protective film over
hole -arrow A-.
– Unscrew clamping bolt -4- as far as possible using a screw‐
driver -1-.
– Push retainer -3- for housing inwards.
– Pull housing -2- out of mounting bracket -arrow B-.
Installing
2.6.2 Removing and installing cap for housing

Removing
– Remove housing ⇒ page 171 .
– Pull retaining clips apart -arrows- and detach cap -2- from
housing -1-, using an awl if necessary.
Installing
– Press on housing cap until it engages audibly.
2.6.3 Removing and installing exterior door

handle
Removing

– Pull exterior door handle -1- in direction of -arrow-; exterior

door handle will be detached from operating lever in mounting
bracket.
– Swivel exterior door handle -1- outwards -arrow- and take out
of mounting on mounting bracket.
– On vehicles with Keyless Entry system, unplug electrical con‐
nector -2- from exterior door handle.
Installing
– Renew backing plates -1- and -2- for door handle if they are
damaged or brittle.
– Insert exterior door handle -1- -arrow A-, making sure that ex‐
terior door handle engages in mounting -2- on mounting brack‐
et -3-.
– Swivel exterior door handle -1- in direction of -arrow B- and
push in »driver« -5- in front of operating lever -4- in mounting
bracket.
– Press retainer for housing towards exterior door handle.
– Install housing ⇒ page 171 .

2.6.4 Removing and installing trim for exterior

door handle
On vehicles without Keyless Entry system, a trim is fitted instead
of the door handle contact sensor.
Removing
– Prise out trim -2- for exterior door handle using an awl -1- at
point indicated in illustration -arrow-.
– Pull trim for exterior door handle out of exterior door handle
-3-.
Installing
– Push in trim for exterior door handle until it engages audibly.
2.6.5 Removing and installing trim strips on

door handle
Removing and installing trim strip on door handle ⇒ page 173
Removing and installing trim strip on cap ⇒ page 173
Removing and installing trim strip on door handle:
Removing
– Detach trim strip -4- from door handle -1- -arrow A-.
Installing
– Tighten bolt -5- to 0.2 Nm.
• Bolt head must not protrude above contact surface for trim
strip.
Removing and installing trim strip on cap:
Removing
– Remove cap ⇒ page 171 .
– Pull trim strip -3- off cap -2- -arrow B-.
Installing

2.7 Removing and installing mounting

bracket
Caution
Risk of malfunction

♦ Removal lever - 80-200 -
Removing
et -arrow-.
- 80-200- .
Note


ing components:
Installing
Tightening torques
♦ ⇒ “2.2 Exploded view - door handle and door lock”,
page 165
2.8 Removing and installing door lock

⇒ “2.8.1 Removing and installing door lock”, page 175
⇒ “2.8.2 Removing and installing operating cable for door lock”,
page 176
⇒ “2.8.3 Removing and installing operating cable for interior door
handle”, page 177
2.8.1 Removing and installing door lock
Caution
Risk of malfunction
Removing
et -arrow-.
- 80-200- .
Note


ing components:
Installing
Tightening torques
page 165

for door lock
Caution
Risk of malfunction
Removing
– Remove mounting bracket and door lock ⇒ page 175 .
– Turn operating cable on lever -1- 90° in direction of -arrow A-
and take it out of cable support bracket -2-.
– Turn operating cable on operating lever -3- for door lock in
direction of -arrow B-.
• The operating cable must be aligned with the opening on the
operating lever.

– Disengage operating cable -1- from operating lever by press‐

ing cable support bracket -3- out of mounting on mounting
bracket -2- -arrow-.
– Take out operating shaft.
Installing

for interior door handle
Caution
Risk of malfunction
♦ When removing and installing, make sure the operating
cable is not kinked or damaged.
Removing
– Press door lock -1- to the side.
– If necessary, unplug electrical connector -2-.
– Disengage operating cable -3- from door lock support bracket

-2- -arrow A-.
– Turn nipple -1- 90° in direction of -arrow B- and take it out of
release lever -4- for interior door handle.
Installing

– Insert nipple -2- in release lever -3- for interior door handle
-bottom arrow-.
– Turn nipple 90° -top arrow- and press operating cable into ca‐
ble support bracket on door lock -1- until it engages audibly.
Tightening torques
page 165

Removing
– Unscrew bolts -2- and detach striker -1-.
Installing
Note
♦ The striker shim plate with the pins -arrows- must be posi‐
tioned exactly in the hole.
♦ After adjusting the striker, the pins must be sheared off cleanly.
♦ When a new part is installed, the sheared-off striker pins must
be removed from the vehicle.
2.10 Removing and installing inner door cov‐

er
Note
The illustration shows the cover for vehicles with power latching
system, and additionally it shows fasteners that must be released
prior to removal.

1 - Cover
Vehicles without power latch‐
ing system

door trim (rear) .
– Pull electrical wiring out

of retaining clips -5-.
– When removing cover, it

is important to start at
the top.
Vehicles with power latching

system

door trim (rear) .
– Disconnect power sup‐

ply to power latching
motor.
– Release fasteners (5x)

by turning them to the
left and pull cover out of
inner door panel.
2 - Grommet with Bowden ca‐

ble
Caution
Do not kink Bowden ca‐
bles when installing.
❑ When installing, make sure component is seated correctly -arrows-.

3 - Bowden cable for interior door handle
4 - Fastener (5x)
– To remove cover, release fasteners by turning them to the left.
– Must engage audibly during installation

2.11 Removing and installing power latching motor - V329-
1 - Rear left power latching mo‐

tor - V307-
❑ Removing
door trim (rear) .

nector for motor.
– Unscrew bolts at motor.
– Guide Bowden cable

out of cable reel.
❑ Installing
– To install, first insert nip‐
ple of cable into cable
reel.
– Insert cable into groove

on cable reel through
360°, as shown in detail
view.
– Clip Bowden cable into

motor at side -arrows-.
– Secure motor by tight‐

ening bolts to specified
torque.
2 - Bowden cable
4 - Bolt
❑ 3 Nm

2.12 Removing and installing window guide
1 - Window guide
❑ Removing
– Door trim and window
frame trim removed ⇒
window frame trim .
– Trim strip for door re‐

moved ⇒ page 349
– Trim panel for B-pillar
– Trim panel for C-pillar

– Door window removed

⇒ page 316
– Disengage window
guide from flange at un‐
derside of window frame
and detach downwards.
– Detach window guide at

B-pillar (self-adhesive).
– Pull window guide out of

trim panel for B-pillar to‐
wards rear and unclip at
C-pillar (4x).
– Detach inner window

slot trim strip upwards
from door flange.
– Detach window guide at

B-pillar and C-pillar from door.
– Lift window guide out of door.

❑ Installing
– To facilitate assembly, coat window guide with soap solution.
– Position window guide at B-pillar (top) and slide it towards rear into guide with clip ⇒ page 182 .
– Moulded section should touch door at rear (longitudinal direction).
– Press window guide onto sides of window frame towards rear and clip onto C-pillar.
– Install trim panels for B-pillar and C-pillar and insert window guide from side.
– Press on inner window slot trim strip.
Caution
Bonding surface must be
free of dust and grease.
– Clean bonding surface on door with cleaning solution - D 009 401 04- .

– Bond sealing strip onto door at B-pillar using double-sided adhesive tape.
2 - Door
3 - C-pillar seal
4 - B-pillar seal
Inserting guide moulding

– Guide moulding with clip -1- must be inserted at B-pillar (top)
-arrow-, as shown.
2.13 Removing and installing window slot

trim strip
Preparing removal tool - T40219- :

• Before removing window slot trim strip, carefully bend removal
tool - T40219- at the point indicated -arrow- so that removal
tool can be applied behind retaining strip.
Removing
Rep. gr. 70 ; Door trim (rear); Removing and installing window
frame trim .
– Detach inner window slot trim strip from door shell.

– Insert removal tool - T40219- next to guide -4- for window slot
trim strip -3- and apply at retaining strip -2-.
• Front section -1- of removal tool - T40219- must be positioned
– Press removal tool - T40219- lightly in direction of -arrow- to
release component.
• You should hear the retaining strip disengage.
– Carefully pull window slot trim strip upwards off door flange
using removal tool - T40219- .
– Detach window slot trim strip.
Installing
Note
For installing, you can coat the bottom edge of the window slot
trim strip with tyre assembly paste.
– Position window slot trim strip -1- at trim panel for B-pillar on
door seam and press on evenly -arrows A-; retaining strip -2-
should engage audibly.
• When fixing strip in position -arrow-, retaining strip should en‐
gage underneath retaining plate -3-.

60 – Sunroof
1 Sliding sunroof
⇒ “1.1 Exploded view - sliding sunroof”, page 184
⇒ “1.2 Exploded view - sunroof sun blind”, page 190
⇒ “1.3 Removing and installing sliding sunroof frame”,
page 190
⇒ “1.4 Removing and installing sliding sunroof panel”,
page 193
⇒ “1.5 Adjusting sliding sunroof panel”, page 194
⇒ “1.6 Removing and installing glass panel”, page 195
⇒ “1.7 Checking and adjusting zero position for guide rail”,
page 197
⇒ “1.8 Removing and installing sliding sunroof adjustment control
unit J245 ”, page 198
⇒ “1.9 Adapting sliding sunroof adjustment control unit J245 ”,
page 199
⇒ “1.10 Removing and installing sliding sunroof seals”,
page 200
⇒ “1.11 Removing and installing sliding sunroof sun blind”,
page 202
⇒ “1.12 Removing and installing cables for sunroof sun blind”,
page 204
⇒ “1.13 Removing and installing sun blind”, page 205
⇒ “1.14 Removing and installing wind deflector”, page 205
1.1 Exploded view - sliding sunroof

⇒ “1.1.1 Exploded view - sliding sunroof”, page 184
⇒ “1.1.2 Exploded view - sliding sunroof, sliding sunroof frame”,
page 186
⇒ “1.1.3 Exploded view - sliding panoramic sunroof, Saloon”,
page 188
⇒ “1.1.4 Exploded view - sliding panoramic sunroof, Avant”, page
189
1.1.1 Exploded view - sliding sunroof
184 Rep. gr.60 - Sunroof

1 - Sliding headliner
❑ Only on vehicles with
glass roof
tach sunroof panel.
⇒ page 205
2 - Spring for sliding headliner
(right-side)
tach trim frame for moul‐
ded headliner ⇒ Gener‐
al body repairs, interior;
Rep. gr. 70 ; Roof trim;
moulded headliner
❑ To remove, unscrew
bolt -7- (front and rear).
❑ Push front spring -2- for‐
wards / rear spring
backwards off sliding
headliner and take out
springs.
❑ Pull sliding headliner
sideways out of guide
rail on opposite side and
lift out.
3 - Bolt
❑ 1.5 Nm
4 - Seal
❑ Renewing ⇒ page 200
5 - Sunroof panel
❑ To remove, tilt sunroof
panel.
❑ Bellows removed ⇒ page 193
❑ Unscrew bolts (left and right) and lift out sunroof panel.
6 - Spring for sliding headliner (left-side)
1. Sliding sunroof 185

Spring for sliding headliner
1.1.2 Exploded view - sliding sunroof, sliding sunroof frame
1 - Frame
❑ Removing:
❑ Fold seat backrests as
far as possible to the
rear.
❑ Lower headliner ⇒ Gen‐
headliner .
❑ Sunroof panel removed
❑ Detach water drain ho‐
ses.
– Remove nuts -4- and
bolts -2- from frame.
– Lift frame out of vehicle

through rear door.
❑ Installing:
– Bolt frame loosely onto
roof with nuts and bolts.
– Fit water drain hoses.
– Use ∅ 12 mm drill bit

(front right) and ∅
10 mm drill bit to secure
frame in body
⇒ page 187 , and, start‐
ing at front (centre) and
working towards rear,
tighten nuts (left and
right) to torque.
– Tighten bolts to torque

in same sequence.
2 - Bolt
❑ 8 Nm
3 - Wind deflector
4 - Nut
❑ 8 Nm
5 - Bolt
❑ 4 Nm
6 - Motor
❑ Removing:
Note
Remove motor only with sunroof

panel closed.
– Interior light removed

– Unplug electrical connector for motor.
– Unscrew bolts -5- and take motor out of headliner opening.

❑ After removing and installing a motor, motor must be adapted ⇒ page 199 .
Attachment points for frame

– When installing sunroof, frame must be fixed in position at front
right -arrow- after first nut -1- with a ∅ 12 mm drill and...
– ... at rear left (slot) -arrow- before final bolt -1- with a ∅ 10 mm
drill.
– Tighten nuts and bolts to torque, starting at front (centre) and
working towards rear ⇒ page 186 .

1.1.3 Exploded view - sliding panoramic sunroof, Saloon
Note
♦ Only features/components which are different from the sliding panoramic sunroof for Avant models are
shown.
♦ The procedures for removing and installing the individual components of the sliding panoramic sunroof on
Saloon models are the same as for Avant models.
1 - Frame for sliding panoramic

sunroof
⇒ page 192
2 - Seal
3 - Wind deflector
⇒ page 206
4 - Sunroof panel »1«
⇒ page 195
5 - Panel seal
⇒ page 196
7 - Bolt
❑ 3 Nm
8 - Bolt
❑ 7 Nm

1.1.4 Exploded view - sliding panoramic sunroof, Avant

sunroof
⇒ page 192
2 - Seal
3 - Wind deflector
⇒ page 206
⇒ page 195
5 - Panel seal
⇒ page 196
7 - Bolt
❑ 3 Nm
8 - Bolt
❑ 7 Nm

1.2 Exploded view - sunroof sun blind
1 - Tension bow
⇒ page 204
2 - Actuator at sun blind cable
❑ Can only be renewed to‐
gether with cable
⇒ page 204
3 - Stop for cable
– Removing ⇒ page 204
4 - Bolt
❑ 1 Nm
5 - Sun blind
⇒ page 202
– Pull tension bow off sun
blind fabric (at side).

sunroof
1.3 Removing and installing sliding sunroof

frame
⇒ “1.3.1 Removing and installing sliding sunroof frame - Saloon”,
page 190
⇒ “1.3.2 Removing and installing sliding sunroof frame - Avant”,
page 192
1.3.1 Removing and installing sliding sunroof

frame - Saloon
Caution
After removing and installing mechanical components or con‐

trol units for the sliding panoramic sunroof, always perform
encoding/adaption via the Guided Functions in Guided Fault
Finding mode (diagnostic address 46) ⇒ Vehicle diagnostic
tester.

1 - Bolt
❑ 3 Nm
2 - Sliding sunroof adjustment
❑ Performing adaption
⇒ page 199
3 - Bolt
❑ 8 Nm
4 - Roof
sunroof
❑ Removing
– Tilt front seat backrests
to rear.
– Only lower headliner (do

not remove) ⇒ General
Rep. gr. 70 ; Roof trim
panels; Removing and
installing moulded
headliner .

nectors.
– Detach water drain ho‐

ses (front and rear).
Note
♦ Only unscrew central bolts (at

sides) from frame as a final step.
♦ Two mechanics must hold the
frame in position so that a third
can remove the bolts and the
frame can be lifted out.
– Unscrew bolts on both sides; do not unscrew central bolts.
– Have other mechanics hold frame; only then can central bolts be loosened and then frame be lifted out
through roof opening.
❑ Installing
– Loosely secure frame with bolts.
– Locate frame at locating holes with ∅ 8 mm drill (front and rear) ⇒ page 193 .
– Tighten bolts along width of frame to torque (first at front, then at rear).
– Tighten bolts along length of frame alternately to torque (from rear to front).
– Connect water drain hoses (front and rear) to frame.
6 - Sun blind
7 - Sunroof roller blind control unit - J394-
❑ Performing adaption ⇒ page 199

1.3.2 Removing and installing sliding sunroof frame - Avant
1 - Bolt
❑ 3 Nm
2 - Sliding sunroof adjustment
❑ Performing adaption
⇒ page 199
3 - Bolt
❑ 8 Nm
4 - Roof
sunroof
❑ Removing
headliner .

nectors.
– Detach water drain ho‐

ses (front and rear).
Note
♦ Only unscrew central bolts (at

sides) from frame as a final step.
♦ Two mechanics must hold the
frame in position so that a third
can remove the bolts and the
frame can be lifted out.
– Unscrew bolts on both sides; do not unscrew central bolts.
– Have other mechanics hold frame; only then can central bolts be loosened and frame be lifted out of
vehicle towards rear through rear lid opening.
❑ Installing
– Loosely secure frame with bolts.
– Locate frame at locating holes with ∅ 10 mm drill (front and rear) ⇒ page 193 .
– Tighten bolts along width of frame to torque (first at front, then at rear).
– Tighten bolts along length of frame alternately to torque (from rear to front).
– Connect water drain hoses (front and rear) to frame.
6 - Sun blind
7 - Sunroof roller blind control unit - J394-
❑ Performing adaption ⇒ page 199

Attachment points for frame

– When installing, frame must be located with ∅ 10 mm drill bits
in elongated hole at front left -arrow- next to sliding sunroof
adjustment control unit - J245- and...
– ... in elongated hole at rear left -arrow- next to sunroof roller

blind control unit - J394- .
– Tighten bolts along width of frame to torque (first at front, then
at rear).
– Tighten bolts along length of frame alternately to torque (from
rear to front).

panel
⇒ “1.4.1 Removing and installing sliding sunroof panel”,
page 193
⇒ “1.4.2 Removing and installing bellows”, page 193

panel
Procedure
– Pull bellows out of sunroof panel and frame to side.
– Unscrew bolts -arrows- on both sides and lift out sunroof pan‐
el.
1.4.2 Removing and installing bellows

1 - Bolt
❑ 4 Nm
2 - Sunroof panel
⇒ page 193
3 - Bellows
❑ Pull out of sunroof panel
and frame from side.
1.5 Adjusting sliding sunroof panel

⇒ “1.5.1 Adjusting sliding sunroof panel”, page 194
⇒ “1.5.2 Adjusting panoramic sunroof”, page 195
1.5.1 Adjusting sliding sunroof panel

Adjusting
– To avoid wind noise, adjust the height of the sunroof panel at
the front and rear as shown in illustration.
– Check the height adjustment at the points where the rounded
corners merge with the straight parts of the roof cut-out at the
front and back.
– The sunroof panel should not be higher than the roof at any
point at the front or lower than the roof at any point at the rear.
– For height adjustment, always close sunroof from open (non-
tilted) position.

1.5.2 Adjusting panoramic sunroof

Adjusting
• Arrow = direction of travel (front)
♦ Dimension »a« = 1.5 mm
♦ Dimension »b« = 1.0 mm
♦ Dimension »c« = 0.5 mm
– All dimensions ± 0.5 mm
1.6 Removing and installing glass panel

⇒ “1.6.1 Removing and installing panel 1 - sliding panoramic sun‐
roof”, page 195
⇒ “1.6.2 Removing and installing panel 2 - sliding panoramic sun‐
roof”, page 196
1.6.1 Removing and installing panel »1« - slid‐

ing panoramic sunroof
Caution
Sunroof must not be moved if sunroof panel is removed - risk

of damage.
Note
If bolts securing sunroof panel have been removed completely,

they must be renewed.

1 - Bolt
❑ 2x on each side (front
and rear)
❑ 7 Nm
2 - Mounting (front) for guide
rail
placement part
❑ Adjusting guide rail
⇒ page 198
– To remove, tilt sunroof
panel and pull off trim
panels towards rear.
– Remove bolts (rear) and

open sunroof panel to‐
wards rear slightly.
– Unscrew bolts (front)

and lift out sunroof pan‐
el.
– Installation is carried out

in reverse sequence.
❑ Adjust sliding sunroof
panel ⇒ page 195 .
4 - Mounting (rear) for slotted
guide
placement part
❑ Adjusting guide rail
⇒ page 198
1.6.2 Removing and installing panel »2« - slid‐

ing panoramic sunroof
Note
If bolts for securing sunroof panel have been completely removed,

they must be renewed.

1 - Bolt
❑ 3 Nm
❑ To remove, fully open
sun blind and pull off
acoustic seal to the side
⇒ Item 2 (page 189) .
❑ Unscrew bolts on each
side (front and rear) and
lift out sunroof panel.
– Installation is carried out
in reverse sequence.
3 - Panel seal
– Sunroof panel »2« re‐
moved
– Starting at the side, pull

seal off sunroof panel
(left and right).
– Pull seal (front) upwards

out of sunroof panel.
❑ When installing, align
seal (front) centrally with
sunroof panel and press
into guides
⇒ page 200 .
– Fit ends of seal onto
lugs on moulding.
1.7 Checking and adjusting zero position for

guide rail
⇒ “1.7.1 Zero position - Saloon”, page 197
⇒ “1.7.2 Zero position - Avant”, page 198
1.7.1 Zero position - Saloon

Checking
Zero position can be checked with sunroof panel fitted.
– Bellows removed
– Retract sunroof panel and close again.
– On vehicles with glass panel, push back sliding headliner as
far as it will go.
– Close sunroof.

– If zero position is correct, guide pin -1- in tilt arm must be cen‐
trally aligned with marking -arrow- on slotted guide -2-.
Adjusting
– Sliding/tilting sunroof motor removed
– Sliding/tilting sunroof panel removed
– Slide slotted guide on both sides into zero position by hand (as
shown).
– Adjust motor to zero position and install.
1.7.2 Zero position - Avant

– Sunroof panel and sliding sunroof adjustment control unit -
J245- removed
– Cables are adjusted correctly when tab -1- and guide
-arrows- on rail -2- are between the two markings, as shown
in detail view.
– Slide slotted guide on both sides into zero position by hand (as
shown).

adjustment control unit - J245-
Caution
After removing and installing sunroof motor, check and, if ap‐

plicable, adjust zero position of guide rail ⇒ page 198 .
– Cover for interior light removed ⇒ Electrical system; Rep. gr.

96 ; Controls; Removing and installing interior light/reading
light (front) .
– Remove bolts (3x) ⇒ Item 1 (page 192) and take motor out
through opening in headliner.
– After installing, perform adaption.

1.9 Adapting sliding sunroof adjustment

⇒ “1.9.1 Adjusting zero position (motor) - Saloon”, page 199
⇒ “1.9.2 Adaption for motor”, page 199
1.9.1 Adjusting zero position (motor) - Saloon

– Motor removed, electrical connections plugged in.
– Move rotary control to “roof closed” position.
– Motor automatically runs to zero position and is switched off.
– Install motor in this position with sunroof closed.
1.9.2 Adaption for motor
Note
After a motor has been removed and re-installed or renewed, the

motor must be adapted so that the sliding/tilting sunroof can op‐
erate properly.
WARNING
• Sunroof panel must be installed when performing adap‐

tion - risk of damage.
• When the sliding sunroof adjustment control unit - J245- /
sunroof roller blind control unit - J394- has been renewed,
it has to be encoded and adapted via the Guided Func‐
tions mode in the Guided Fault Finding routine (diagnostic
address 46) ⇒ Vehicle diagnostic tester.


seals
⇒ “1.10.1 Removing and installing sunroof seals - Saloon”,
page 200
⇒ “1.10.2 Removing and installing sunroof seals - Avant”,
page 200
⇒ “1.10.3 Removing and installing seal for sliding panoramic sun‐
roof”, page 201
1.10.1 Removing and installing sunroof seals -

Saloon
Procedure
– Sunroof panel -3- removed
– Pull seal -2- out of sunroof panel -3-.
– Starting in centre, press new seal into sunroof panel -3- at rear
edge of panel.
Note
To make it easier to install the seal, coat edge of panel with soap
solution.
1.10.2 Removing and installing sunroof seals -

Avant
Procedure
Note
Spray seal with soap solution to make installation easier.
– Align seal centrally with sunroof panel and press into two
guides (front).
– Press seal -1- into guides at side of sunroof panel -2-.

– It is only possible to remove seal -3- when sunroof panel »2«

is removed.
– To do so, pull seal off frame -4- (at side).
1.10.3 Removing and installing seal for sliding

panoramic sunroof
♦ Roller - T10563-
Procedure
– Remove both sunroof panels.
– Remove frame for sliding panoramic sunroof ⇒ page 192 .

– Pull seal -1- to the side off body flange.
Note
♦ The bonding surfaces must be free of dust and grease.

♦ Before bonding, heat bonding surfaces and seal to approx. 40°
C.
– Remove any residual adhesive and clean body flange.

– Clean bonding surfaces on body with cleaning solution - D 009
401 04- .
– Peel protective film off adhesive strip at rear section of seal
and then press on rear section of seal (joint should be in centre
of vehicle; observe marking).
– Press seal in at front corners.
– Press on front section of seal.
– Press seal in at rear corners.
– Press on rear section of seal.
– Press on side sections of seal; if necessary, compress seal
evenly to take up any excess length.
– Using roller - T10563- , press down on seal again all around
in area of adhesive strip.

sun blind
⇒ “1.11.1 Removing and installing sliding sunroof sun blind”, page
202
⇒ “1.11.2 Removing and installing motor for sun blind”,
page 204

sun blind
Removing
– Sun blind fully open.
– Frame and sunroof panel »2« removed
– Sun blind adjustment motor removed
– Press fastener -arrow- for tension bow -1- on left side of ac‐
tuator -2- to release it.
– Slide in tension bow in direction of -arrow-.

– On the opposite side, lift tension bow -1- off actuator -2- and
pull off fabric tube to the side.
– Using a small screwdriver, press fastener -arrow- outwards to

the side and disengage.
– Slide actuator -1- of cable forwards slightly.
– Secure shaft in roller for sun blind -1- to prevent it from un‐
winding and locate with piece of wire -2-.
– Press retaining tab -2- back in direction of -arrow- with a small

screwdriver or similar tool and lift out shaft -1-.
– Pull sun blind fabric out of frame towards rear and remove to‐
gether with sleeve.
Installing

– Make sure that reinforcement at side engages in guide lugs

-1- on frame and is positioned beneath guide lug -2-.
– Pull off locking pin on sun blind roller only after it has been
inserted in frame.
– With tension bow installed, slide sun blind towards rear as far
as stop and re-install sunroof roller blind control unit - J394- .
Note
♦ If the shaft in the sun blind roller has unwound, the pre-tension
can be re-established as follows.
♦ Before pre-tensioning the sun blind, tap the roller lightly to
make sure that the spring is evenly slack.
– Turn shaft of unwound sun blind -1- until slight resistance is

noticeable.
– Then turn shaft at end piece -arrow- 12 turns while holding
roller in place and secure with locking pin -2- or wire to prevent
it from unwinding.
– Sun blind can now be re-installed.
1.11.2 Removing and installing motor for sun

blind
– Headliner removed ⇒ General body repairs, interior; Rep. gr.
70 ; Roof trim panels; Removing and installing moulded head‐
liner .
– Unscrew bolts (3x) ⇒ Item 1 (page 192) and detach motor from
frame.
– After installing, perform adaption.
1.12 Removing and installing cables for sun‐

roof sun blind
– Sunroof frame removed
– Sunroof roller blind control unit - J394- removed
– Unscrew bolt -arrow- and detach stop -1-.
– Pull cable out of frame towards rear.
– When installing, make sure that actuators run parallel.
Adjusting parallel running for cables
• When installing, the new cables must be adjusted so that they
run parallel.
– Draw cables into frame on both sides.

– Insert stop -1- and secure with bolt.

– Slide cables on both sides towards rear as far as stop and
install sunroof roller blind control unit - J394- .
– Perform adaption ⇒ page 199 .
1.13 Removing and installing sun blind

Removing
– Sunroof panel removed
– Unscrew bolt -2- for spring -3-.
– Slide headliner -1- back slightly and pull front spring out to‐
wards front.
– Press out rear spring towards rear.
– Lift out headliner.
Installing
1.14 Removing and installing wind deflector

⇒ “1.14.1 Removing and installing wind deflector - Saloon”, page
205
⇒ “1.14.2 Removing and installing wind deflector - Avant”,
page 206
1.14.1 Removing and installing wind deflector -

Saloon
Removing:
– Open sliding sunroof fully.
– Press wind deflector down at front and pull arms of wind de‐
flector out of mounting towards centre of vehicle.

– Take wind deflector -1- out of sunroof opening diagonally to‐

wards rear.
– Install in reverse order of removal.
Spring for wind deflector

– Place spring -3- in bracket -1- for wind deflector.
– Insert spring in outer groove of wind deflector -2-.
1.14.2 Removing and installing wind deflector - Avant


sunroof
2 - Wind deflector
– To remove, open sun‐
roof panel »1« and re‐
tract towards rear of ve‐
hicle.
– Unfasten wind deflector

net from retaining strip,
starting at side (front)
⇒ page 208 .
3 - Spring for wind deflector
Disengaging wind deflector

– Disengage spring -2- from mounting and wind deflector -1-.
– Press pivot pins on wind deflector -arrows- out of guide rail on
sliding sunroof frame towards outside.

Unfastening wind deflector from frame

– To remove, gradually unfasten wind deflector net from retain‐
ing strip -1-, starting at side -arrow-.
– Install in reverse order of removal.

2 Water drain hoses

⇒ “2.1 Overview - water drain hoses”, page 209
⇒ “2.2 Cleaning water drain hoses”, page 211
⇒ “2.3 Removing and installing water drain hoses”, page 213
2.1 Overview - water drain hoses

⇒ “2.1.1 Overview - water drain hoses, Saloon”, page 209
⇒ “2.1.2 Overview - water drain hoses, Saloon with panoramic
sunroof”, page 210
⇒ “2.1.3 Overview - water drain hoses, Avant with panoramic
sunroof”, page 211
2.1.1 Overview - water drain hoses, Saloon
1 - Water drain hose (front)

❑ Water drain hoses
(front) are routed along
A-pillars and end behind
door at bottom of A-pil‐
lar.
❑ To clean, access hose
from sliding panoramic
sunroof.
2 - Sunroof frame
3 - Water drain hose (rear)
❑ Water drain hoses (rear)
are routed along D-pil‐
lars and end in wheel
housing above wheel
housing liner.
❑ Clean from bottom end
of hose.
❑ To do so, you must first
remove wheel housing
liner (rear).
4 - A-pillar grommet
❑ Must be pressed in com‐
pletely
2. Water drain hoses 209

2.1.2 Overview - water drain hoses, Saloon with panoramic sunroof

⇒ page 215
2 - Panoramic sunroof
⇒ page 216
4 - Grommet

2.1.3 Overview - water drain hoses, Avant with panoramic sunroof

⇒ page 215
2 - Panoramic sunroof
⇒ page 216
4 - Grommet
2.2 Cleaning water drain hoses

⇒ “2.2.1 Cleaning water drain hoses (front)”, page 211
⇒ “2.2.2 Cleaning water drain hoses (rear)”, page 212
2.2.1 Cleaning water drain hoses (front)


♦ Cleaning and insertion aid - VAS 6620-
Water drain hoses (front) are routed on and end at outer A-pillar.
Note
Use cleaning and insertion aid - VAS 6620- to clean water drain
hoses.
– Clean from top end of hose (sunroof panel must be open).
2.2.2 Cleaning water drain hoses (rear)

♦ Cleaning and insertion aid - VAS 6620-
Water drain hoses (rear) are routed on D-pillars and end in wheel
housings (rear).
Note
Use cleaning and insertion aid - VAS 6620- to clean water drain
hoses.
Clean from bottom end of hose.

To do so, loosen rear adjacent section of wheel housing liner
(rear) and press to the side.

2.3 Removing and installing water drain ho‐

ses
⇒ “2.3.1 Removing and installing water drain hoses (front) - Sa‐
loon”, page 213
⇒ “2.3.2 Removing and installing water drain hoses (rear) - Sa‐
loon”, page 214
⇒ “2.3.3 Removing and installing water drain hoses (front) -
Avant”, page 215
⇒ “2.3.4 Removing and installing water drain hoses (rear) -
Avant”, page 216
2.3.1 Removing and installing water drain hoses (front) - Saloon

❑ Removing:
– A-pillar trim removed ⇒
Passenger compart‐
ment trim panels; Re‐
moving and installing A-
pillar trim .
– Pull water drain hose off

connection -5-, open
hose retainer -4- and
pull hose out at clip.
– Unfasten grommet -2- at

A-pillar and pull water
drain hose downwards
out of A-pillar.
❑ Installing:
– When installing, pull
hose into A-pillar from
below.
– Push upwards and pull

out as shown in detail
view. Then attach it to
connection on sliding
panoramic sunroof.
– Press water drain hose

into clips -arrows- and
secure with hose retain‐
ers.
2 - Grommet
❑ Permanently attached
to water drain hose;
must be pressed into A-pillar (bottom).
3 - Connection (front) for water drain
❑ To fit hose, press it onto end piece as far as stop.
4 - Hose retainer
5 - Connection (front)

2.3.2 Removing and installing water drain hoses (rear) - Saloon

❑ Removing:
– D-pillar trim removed ⇒
moving and installing D-
pillar trim .
– Wheel housing liner

(rear) removed
⇒ page 410
– Unfasten hose retainers

-3- and detach water
drain hose from connec‐
tion -2-.

top of wheel housing lin‐
er and pull out water
drain hose downwards.
❑ Installing:
– When installing, insert
hose through wheel
housing from below.
– Slide it upwards and

route it along D-pillar, as
shown, and attach it to
end piece of sliding pan‐
oramic sunroof.
– Press in grommet at
rear of wheel housing.
– Secure water drain hose

in position with hose re‐
tainer.
2 - Connection (rear) for water drain

3 - Hose retainer
4 - Grommet
❑ Must be pressed into wheel housing completely
5 - Wheel housing

2.3.3 Removing and installing water drain hoses (front) - Avant

❑ Removing:
– A-pillar trim removed ⇒
moving and installing A-
pillar trim .

connection -3- and out
of retainer -4-.
– Unclip water drain hose

(4 clips) -arrows-.

A-pillar and pull water
drain hose downwards
out of A-pillar.
❑ Installing:
– When installing, pull
hose into A-pillar from
below.
– Slide hose through hole

in A-pillar reinforcement
and clip in.
– Slide hose through up‐

wards and pull out as
shown in detail view.
Then attach it to con‐
nection on sliding pan‐
oramic sunroof.
– Press water drain hose

into clips -arrows- and
secure in retainer -4-.
2 - Grommet
❑ Permanently attached to water drain hose; must be pressed into A-pillar (bottom).
3 - Connection
4 - Bracket

2.3.4 Removing and installing water drain hoses (rear) - Avant

❑ Removing:
– C-pillar trim removed ⇒
moving and installing C-
pillar trim
– Wheel housing liner

(rear) removed
⇒ page 410

connection -2-.
Note
Before pulling out water drain hose,

attach e.g. a cord to make it easier
to pull it in.

top of wheel housing lin‐
er and pull out water
drain hose downwards.
❑ Installing:
– When installing, insert
hose through wheel
housing from below.
– Slide hose through up‐

wards, pull it in through
D-pillar, as shown, and
attach it to connection
on sliding panoramic
sunroof.
– Press in grommet at rear of wheel housing.
2 - Connection
3 - C-pillar
4 - Grommet
❑ Must be pressed into wheel housing completely
5 - Wheel housing

63 – Bumpers
1 Bumper (front)
⇒ “1.1 Exploded view - bumper cover”, page 217
⇒ “1.2 Exploded view - impact bar”, page 225
⇒ “1.3 Removing and installing bumper cover”, page 226
⇒ “1.4 Removing and installing impact bar”, page 232
⇒ “1.5 Removing and installing attachments”, page 239
1.1 Exploded view - bumper cover

⇒ “1.1.1 Exploded view - bumper cover, Audi A6/S6 up to model
year 2014”, page 217
⇒ “1.1.2 Exploded view - bumper cover, Audi A6 from model year
⇒ “1.1.3 Exploded view - bumper cover, lock carrier cover and
closure plate, Audi A6/S6”, page 220
⇒ “1.1.4 Exploded view - bumper cover, allroad”, page 220
⇒ “1.1.5 Exploded view - bumper cover, Audi RS 6”, page 222
⇒ “1.1.6 Exploded view - bumper cover, lock carrier cover and
closure plate, Audi RS 6”, page 224
1.1.1 Exploded view - bumper cover, Audi A6/S6 up to model year 2014
1. Bumper (front) 217

1 - Bumper cover
⇒ page 226
2 - Bolt
❑ 2x
❑ 4 Nm
3 - Mounting
❑ For camera for night vi‐
sion system - R212-
⇒ page 241
4 - Bolt
❑ 4x
❑ 6 Nm
5 - Moulded foam insert
⇒ page 245
6 - Clip
❑ 2x
7 - Front parking aid sender
Rep. gr. 94 ; Parking
aid; Removing and in‐
stalling front parking aid
senders
8 - Bumper cover mounting
(front)
⇒ page 245
9 - Bolt
❑ 2x
❑ 4 Nm
10 - Front park assist steering sender
❑ Removing and installing ⇒ Electrical system; Rep. gr. 94 ; Park assist steering; Removing and installing
front sender
11 - Bolt
❑ 4 Nm
12 - Bolt
❑ 1.5 Nm
13 - Bolt
❑ Tightening torque ⇒ Electrical system; Rep. gr. 27 ; Adaptive cruise control system; Overview of fitting
locations - adaptive cruise control
14 - Adaptive cruise control unit (ACC)
❑ Removing and installing ⇒ Electrical system; Rep. gr. 27 ; Adaptive cruise control; Removing and
installing adaptive cruise control unit
15 - Cover for washer jet
❑ For headlight washer system
218 Rep. gr.63 - Bumpers

1.1.2 Exploded view - bumper cover, Audi A6 from model year 2015 onwards

❑ For headlight washer
system
⇒ page 248
2 - Bumper cover
⇒ page 226
3 - Bolt
❑ 2x
❑ 4 Nm
4 - Cover
❑ For air intake grille
❑ Depending on equip‐
ment version
5 - Mounting
❑ For camera for night vi‐
sion system - R212-
⇒ page 242
6 - Bolt
❑ 4x
❑ 6 Nm
⇒ page 246
8 - Clip
❑ 2x
9 - Bumper cover mounting
(front)
10 - Bolt
❑ 2x
❑ 4 Nm
11 - Bolt
❑ 4 Nm
12 - Bolt
❑ 1.5 Nm
13 - Bolt

1.1.3 Exploded view - bumper cover, lock carrier cover and closure plate, Audi
A6/S6
1 - Spoiler lip
⇒ page 244
2 - Bolt
❑ 5x
❑ 1.5 Nm
3 - Closure plate for bumper
cover
⇒ page 243
4 - Lock carrier cover
⇒ page 239
5 - Fastener
6 - Fastener
7 - Air intake grille
⇒ page 249
8 - Bolt
❑ 2x
❑ 2.1 Nm
9 - Bolt
❑ 4x
❑ 5 Nm
1.1.4 Exploded view - bumper cover, allroad
Note
♦ Only features which are different from the standard bumper

are described.
♦ The procedure for removing and installing the bumper cover
is the same as for standard bumpers.

1 - Impact protection
❑ Closure plate -2- re‐
moved
– Remove bolts -16- and
-18-.
– Gradually unfasten clips

on inside and detach im‐
pact protection towards
front.
2 - Closure plate
– Release quick-release
fasteners -17- clockwise
and unscrew bolts -16-
and -18-.
– Pull out closure plate to‐

wards rear.
3 - Bolt
❑ 1.5 Nm
4 - Connecting piece
❑ Clipped into bumper
cover between spoilers
(left and right)
5 - Bolt
❑ 2 Nm
6 - Spoiler (right-side)
– Can be renewed sepa‐
rately.
– Bumper cover removed
– Gradually unclip spoiler

and pull it off bumper cover.
7 - Air intake grille (right-side)

– Closure plate -2- removed
– Unclip gradually from inside and pull off outwards.
8 - Bumper cover
9 - Radiator grille
10 - Bolt
❑ 1.5 Nm
11 - Air intake grille (centre)
– Closure plate removed
– Remove bolts -10- and pull air intake grille off towards rear.
12 - Bolt
❑ 1.5 Nm
13 - Air intake grille (left-side)
– Closure plate -2- removed

– Unclip gradually from inside and pull off outwards.
14 - Bolt
❑ 2 Nm
15 - Spoiler (left-side)
– Can be renewed separately.
– Bumper cover removed
– Gradually unclip spoiler and pull it off bumper cover.
16 - Bolt
❑ 1.5 Nm
17 - Quick-release fastener
❑ Open by turning anticlockwise.
❑ 4x
18 - Bolt
❑ 1.5 Nm
1.1.5 Exploded view - bumper cover, Audi RS 6
1 - Bolt
❑ 2x
❑ 2 Nm
2 - Spoiler (bottom section)
⇒ page 244
3 - Mounting
❑ For spoiler (bottom sec‐
tion)
❑ Secure with locating
clips
⇒ page 245
4 - Bolt
❑ 4x
❑ 2 Nm
5 - Mounting
❑ For moulded foam insert
⇒ page 247
6 - Bolt
❑ 2x
❑ 1.5 Nm
⇒ page 247
8 - Reinforcement strut (cen‐
tre)
⇒ page 240

9 - Mounting
❑ For camera for night vision system - R212-
10 - Bolt
❑ 14x
❑ 1.5 Nm
11 - Bolt
❑ 2x
❑ 3 Nm
12 - Reinforcement strut (side)
13 - Bumper cover mounting (front)
14 - Nut
❑ 3x
❑ 4 Nm
15 - Bolt
❑ 4 Nm
16 - Bolt
❑ 1.5 Nm
17 - Bolt
❑ 1.5 Nm
18 - Bumper cover
20 - Bolt
❑ For headlight washer system

1.1.6 Exploded view - bumper cover, lock carrier cover and closure plate, Audi
RS 6
1 - Spoiler lip
⇒ page 244
2 - Bolt
❑ 7x
❑ 1.5 Nm
3 - Closure plate for bumper
cover
⇒ page 243
4 - Inner air intake grille
logue
⇒ page 250
5 - Lock carrier cover
⇒ page 239
6 - Fastener
7 - Fastener
8 - Mounting
❑ For outer air intake grille
9 - Bumper cover
10 - Outer air intake grille
⇒ page 249
11 - Trim
❑ For outer air intake grille
⇒ “1.5.18 Removing and installing outer air intake grille - Audi RS 6”, page 249
12 - Bolt
❑ 2x
❑ 2.1 Nm
13 - Bolt
❑ 4x
❑ 5 Nm

1.2 Exploded view - impact bar
1 - Nut
❑ 2x
⇒ page 226
2 - Bracket
❑ For ambient tempera‐
ture sensor - G17-
⇒ page 251
3 - Impact bar
❑ Removing and instal‐
ling: left-side
⇒ page 234 , right-side
⇒ page 236
⇒ page 234
5 - Bolt
❑ 2x
6 - Rivet
❑ For attachment to lock
carrier
7 - Bolt
Crash sensors for air‐
bags; Overview of fitting
locations - crash sen‐
sors for airbags
8 - Crash sensor for front air‐
bag
❑ Removing and installing ⇒ General body repairs, interior; Rep. gr. 69 ; Crash sensors for airbags;
Overview of fitting locations - crash sensors for airbags
9 - Bolt
❑ 4.5 Nm
10 - Connecting piece
❑ For supporting bumper cover mounting (front)
11 - Bolt
❑ 4x
❑ 18 Nm
12 - Bolt
❑ 3x
❑ 55 Nm
13 - Bolt
❑ 20 Nm
14 - Lower longitudinal member (front)

15 - Bolt
❑ 20 Nm
16 - Bolt
❑ 20 Nm
Impact bar (front) - tightening torque and sequence

– Tighten nuts -A- to 20 Nm in sequence -1 … 4-.
1.3 Removing and installing bumper cover

⇒ “1.3.1 Removing and installing bumper cover”, page 226
⇒ “1.3.2 Gap widths at bumper cover (front)”, page 229
⇒ “1.3.3 Adjusting bumper cover (front)”, page 230
Caution
For vehicles equipped with adaptive cruise control (ACC),

please observe the following:
• If the bumper is removed and re-installed, or if modifica‐
tions are made to the retainer for the ACC, the adaptive
cruise control system will have to be adjusted ⇒ Running
gear, front-wheel drive and four-wheel drive; Rep. gr. 44 ;
Adaptive cruise control; Adjusting adaptive cruise control .
For vehicles equipped with camera for night vision system -
R212- , observe the following:
tions are made to the radiator grille, it will be necessary to
re-calibrate the camera for night vision system - R212- ⇒
Running gear, front-wheel drive and four-wheel drive;
Rep. gr. 44 ; Night vision system; Calibrating night vision
system .
For vehicles equipped with overhead view camera, observe
the following:
tions are made to the radiator grille, it will be necessary to
re-calibrate the front overhead view camera - R243- ⇒
Communication; Rep. gr. 91 ; Overhead view camera;
Overview of fitting locations - overhead view camera sys‐
tem .

♦ Engine bung set - VAS 6122-
Removing
– Unfasten, but do not remove, wheel housing liner (front) in
area of bumper ⇒ page 406 .
– Remove wheel spoiler ⇒ page 409 .
– Place drip tray underneath connection point for washer fluid
hose.
– Clamp off washer fluid hose -2- with hose clamp -3094- .
– Pull securing clip -arrow- and detach headlight washer fluid
line.
Note
Depending on the equipment version, there may be release tabs

on the connecting piece for the fluid hose.
– Seal hose connection -1- with clean plug from engine bung set
- VAS 6122- .

– Audi RS 6: Remove bolt -arrow-.
– Remove bolts -4-.

– Remove lock carrier cover ⇒ page 239 .
– On vehicles with camera for night vision system, unplug elec‐
trical connector -1-.
– On vehicles with garage door operation control unit, unplug
electrical connector.
– On vehicles with front overhead view camera, unplug electrical
connector.
– Detach side section -3- from side panel (front) -arrow- and de‐
tach bumper cover towards the front with the help of a second
person.
Note
If the side section cannot be detached from the side panel, the
mounting for the bumper cover (front) must be removed
⇒ page 245 .

♦ Vehicles up to model year 2014: electrical connector located
on right side
♦ Vehicles from model year 2015 onwards: electrical connector
located on left side
– On vehicles with adaptive cruise control unit (ACC), unplug
electrical connector -2-.

– e-tron: Unplug electrical connector -2- and move wiring har‐

ness -1- clear.
Installing
– On vehicles with adaptive cruise control unit (ACC), control
units must be re-calibrated ⇒ Running gear, front-wheel drive
and four-wheel drive; Rep. gr. 44 ; Adaptive cruise control;
Adjusting adaptive cruise control .
– On vehicles with camera for night vision system - R212- , the
camera must be re-calibrated ⇒ Running gear, front-wheel
drive and four-wheel drive; Rep. gr. 44 ; Night vision system;
Calibrating night vision system .
Calibration must be performed if one or more of the following
conditions apply ⇒ Vehicle diagnostic tester in “Guided Fault
Finding” or “Guided Functions” mode :
• Camera or control unit has been removed and installed or re‐
newed.
• Damage to bumper cover (front), e.g. from parking accident.
• Bumper cover (front) has been removed and installed.
• Radiator grille has been removed and installed.
• Rear axle has been adjusted.
• Running gear has been modified.
• “No or incorrect basic setting/adaption” is entered in event
memory.
– On vehicles with front overhead view camera - R243- , the
camera must be re-calibrated ⇒ Communication; Rep. gr. 91 ;
Overhead view camera; Overview of fitting locations - over‐
head view camera system .
Tightening torques
1.3.2 Gap widths at bumper cover (front)

A - Bonnet to radiator grille

• Gap width -a- = 4.5 mm
-1- Radiator grille
-2- Bonnet
B - Bonnet to bumper cover
(front)
• Gap width -b- = 3.5 mm
-2- Bonnet
-3- Bumper cover

C - Bonnet to headlight hous‐
ing
• Gap width -c- = 5.9 …5.3
mm
-2- Bonnet
-4- Headlight housing
D - Bumper cover (front) to

wing (front)
• Gap width -d- = zero-gap
panel joint
-3- Bumper cover
-5- Front wing
E - Bumper cover (front) to

headlight housing
• Gap width -e- = 2.0 mm
-3- Bumper cover
-4- Headlight housing
1.3.3 Adjusting bumper cover (front)

♦ Adjusting tool - T40281-
Procedure
• Gap widths ⇒ page 229

• Tightening torques ⇒ page 217

Height adjustment:
– Using adjusting tool - T40281- , loosen or tighten adjusting nut
-5- -arrows- in stages until gap width between bumper cover
-2- and bonnet -3- and headlight -1- is set correctly.
• Dimension -a- = 4.5 mm

• Dimension -b- = 2.5 mm
• Dimension -c- = 2.0 mm
– Tighten bolt -4- to 8 Nm.
– Check gap widths again; if necessary, repeat adjustment proc‐
ess as previously described.
– Check gap width and repeat adjustment if necessary.

Longitudinal adjustment:
– Loosen bolt -3-.
– Adjust bumper cover (front) in longitudinal direction.
– Tighten bolt -3- to specified torque ⇒ Item 11 (page 223) .
– Check gap width ⇒ page 229 and repeat adjustment if neces‐
sary.
1.4 Removing and installing impact bar

⇒ “1.4.1 Removing and installing impact bar”, page 232
⇒ “1.4.2 Removing and installing connecting piece”, page 233
⇒ “1.4.3 Removing and installing mounting (left-side) for impact
bar”, page 234
⇒ “1.4.4 Removing and installing mounting (right-side) for impact
bar”, page 236
⇒ “1.4.5 Removing and installing longitudinal member (front bot‐
tom)”, page 237
1.4.1 Removing and installing impact bar

Removing
Note
Re-attach all cable ties at the same locations when re-installing.


– If fitted, release retaining tabs -arrows A- and detach air duct

-1- -arrow B-.
– Unplug electrical connectors at ambient temperature sensor -

G17- -item 1- and refrigerant pressure and temperature send‐
er - G395- -item 4- and move electrical wiring harness -3-
clear.
– Unscrew nuts and pull out bolts -5- upwards.
– Take impact bar -2- out of mountings.
Note
If impact bar cannot be removed from mountings easily, it must

be levered out.
– If impact bar is renewed, remove bracket for ambient temper‐

ature sensor - G17- ⇒ page 251 .
Installing
Tightening torques
♦ ⇒ Fig. ““Impact bar (front) - tightening torque and sequence”“ ,
page 226
1.4.2 Removing and installing connecting

piece
♦ Drill
♦ Drill bit, ∅ 5 mm
Removing
– Remove bumper cover mounting ⇒ page 10 .


– Unplug electrical connector -1- at horn.
– Unscrew bolt -4- and detach bracket with horn.
– Drill out pop rivet head -3- and knock out rivet stem.
– Loosen bolt -6-, remove bolt -2- and detach connecting piece
-7-.
Installing
Tightening torques
1.4.3 Removing and installing mounting (left-

side) for impact bar
Removing
– Remove wheel spoiler (front left) ⇒ page 406 .
– Remove connecting piece ⇒ page 233 .
– Vehicles with petrol engine: Remove water radiator for charge
air cooling circuit (left-side) and move to rear with coolant ho‐
ses attached ⇒ Rep. gr. 19 ; Radiator/radiator fans; Removing
and installing water radiator for charge air cooling circuit .
– Vehicles with 3.0 ltr. TDI engine (EA 897 generation I): Re‐
move charge air cooler ⇒ Rep. gr. 21 ; Charge air system;
Removing and installing charge air cooler .
– If fitted, unfasten cross member ⇒ Rep. gr. 10 ; Assembly
mountings; Exploded view - assembly mountings .
– If fitted, remove horn bracket(s) ⇒ Electrical system; Rep. gr.
90 ; Horn; Exploded view - horn .

– Have a second mechanic release retaining clips -1- in direction

of -arrow A- and pull condenser -2- upwards out of mounting
points on radiator -arrows B-.
Caution
Risk of damage to condenser and refrigerant pipes/hoses.

♦ Take care not to overstretch, kink or bend refrigerant pipes
and hoses.
– Swivel condenser forwards and to side with lines attached and

secure.
– Mark installation position of mounting relative to lock carrier
(for re-installation).
– Drill off pop rivet and knock out rivet stem.

– Pull lock carrier -2- forwards slightly, swivel out mounting -1-
for impact bar towards left side and detach.
Installing
– Bolt on mounting for impact bar according to mark made dur‐
ing removal.
– To rivet mounting onto lock carrier, remove radiator with radi‐
ator cowl ⇒ Rep. gr. 19 ; Radiator/radiator fans; Removing
and installing radiator .
Tightening torques

1.4.4 Removing and installing mounting

(right-side) for impact bar
Removing
– Remove wheel spoiler (right-side) ⇒ page 409 .
– Remove connecting piece ⇒ page 233 .
– Unplug electrical connector -5- at horn and remove horn
bracket ⇒ Electrical system; Rep. gr. 90 ; Horn; Removing
and installing treble horn - H2- / bass horn - H7- .
– Vehicles with auxiliary heater: Unscrew nut -4- and move cool‐
ant lines clear.
– Move electrical connectors -2 and 3- clear at brackets (press
release mechanism and slide connector downwards).
– Vehicles with secondary air pump motor: Press release tabs
and disconnect secondary air hose -1-.
– Vehicles with 3.0 ltr. TDI engine (EA 897 generation I): Re‐
move charge air cooler ⇒ Rep. gr. 21 ; Charge air system;
Removing and installing charge air cooler .
– If fitted, unfasten cross member ⇒ Rep. gr. 10 ; Assembly
mountings; Exploded view - assembly mountings .
– Unplug electrical connector -1- (and -2- if fitted) for radiator fan
(s); to do so, move locking element towards rear -arrow- and
press release mechanism down.

– Mark installation position of mounting relative to lock carrier

(for re-installation).
– Drill off pop rivet and knock out rivet stem.
– Pull lock carrier -1- forwards slightly, swivel out mounting -2-
for impact bar towards right side and detach.
Installing
– Bolt on mounting for impact bar according to mark made dur‐
ing removal.
– To rivet mounting onto lock carrier, remove radiator with radi‐
ator cowl ⇒ Rep. gr. 19 ; Radiator/radiator fans; Removing
and installing radiator .
Tightening torques
1.4.5 Removing and installing longitudinal

member (front bottom)
♦ Hose clip pliers - VAS 6362-
Removing
– Remove wheel spoiler ⇒ page 406 .
– Remove wheel housing liner ⇒ page 406 .

RS 6:
– Unscrew nut -3-.
– Clamp off coolant hose above and beneath coolant pipe using
hose clamp up to 25 mm - 3094- , release hose clip -2- and
detach coolant hose.
Continued:
– Remove bolts -arrows- and detach longitudinal member (front
bottom) -1-.
Installing
– RS 6: Check coolant level ⇒ Maintenance ; Booklet 411 ;
Maintenance; Cooling system: checking anti-freeze and cool‐
ant level, and correcting if necessary .
Tightening torques
♦ ⇒ “1.1 Exploded view - lock carrier”, page 5

1.5 Removing and installing attachments

⇒ “1.5.1 Removing and installing lock carrier cover”, page 239
⇒ “1.5.2 Removing and installing reinforcement strut (centre) -
vehicles up to model year 2014”, page 240
⇒ “1.5.3 Removing and installing reinforcement strut (side) - ve‐
hicles up to model year 2014”, page 241
⇒ “1.5.4 Removing and installing mounting for camera for night
vision system R212 - vehicles up to model year 2014”,
page 241
⇒ “1.5.5 Removing and installing mounting for camera for night
vision system R212 - vehicles from model year 2015 onwards”,
page 242
⇒ “1.5.6 Removing and installing closure plate for bumper cover
(front) - Audi A6/S6”, page 243
⇒ “1.5.7 Removing and installing closure plate for bumper cover
(front) - Audi RS 6”, page 243
⇒ “1.5.8 Removing and installing spoiler lip”, page 244
⇒ “1.5.9 Removing and installing spoiler (bottom section)”,
page 244
⇒ “1.5.10 Removing and installing mounting for spoiler (bottom
section)”, page 245
⇒ “1.5.11 Removing and installing bumper cover mounting
(front)”, page 245
⇒ “1.5.12 Removing and installing moulded foam insert - Audi A6/
S6 up to model year 2014”, page 245
⇒ “1.5.13 Removing and installing moulded foam insert - Audi A6
from model year 2015 onwards”, page 246
⇒ “1.5.14 Removing and installing moulded foam insert - Audi
RS 6”, page 247
⇒ “1.5.15 Removing and installing mounting for moulded foam
insert - Audi RS 6”, page 247
⇒ “1.5.16 Removing and installing cover for headlight washer jet”,
page 248
⇒ “1.5.17 Removing and installing air intake grille”, page 249
⇒ “1.5.18 Removing and installing outer air intake grille - Audi
RS 6”, page 249
⇒ “1.5.19 Removing and installing inner air intake grille - Audi
RS 6”, page 250
⇒ “1.5.20 Removing and installing bracket for ambient tempera‐
ture sensor G17 ”, page 251
1.5.1 Removing and installing lock carrier

cover

Removing
– Remove spreader rivets -1- using removal lever - 80-200- .
– Pull lock carrier cover -3- out of groove in lock carrier -2-
-arrow-.
– Swivel lock carrier cover forwards and detach.
• This disengages retaining catches -6- at radiator grille -5- and
bumper cover -4-.
Installing
– Insert lock carrier cover into groove in lock carrier and press
on at radiator grille and bumper cover.
1.5.2 Removing and installing reinforcement

strut (centre) - vehicles up to model year
2014
Removing
– If fitted, remove mounting for camera for night vision system -
R212- and move washer fluid hose clear ⇒ page 241 .

– Carefully press retaining clips -2, 3- off guide lug using a

screwdriver.
– Release fastener -4- and detach reinforcement strut -1- to‐
wards rear.
Installing
– Install mounting for camera for night vision system - R212-
⇒ page 241 .
Tightening torques
1.5.3 Removing and installing reinforcement

strut (side) - vehicles up to model year
2014
Removing
– Remove reinforcement strut (centre) ⇒ page 240 .
– Remove mounting for headlight washer jet ⇒ Electrical sys‐
tem; Rep. gr. 92 ; Headlight washer system; Removing and
installing washer jets .
– Carefully press retaining clips -2- off guide lug using a screw‐
driver.
– Release fastener -arrow- and detach reinforcement strut -1-
towards rear.
Installing
1.5.4 Removing and installing mounting for

camera for night vision system - R212- -
vehicles up to model year 2014
Removing


– Unscrew bolts -2, 3, 5, 6- and detach mounting -4- with camera
for night vision system - R212- .
– Release securing clip -7- -arrow- and disconnect fluid line.
– If mounting is to be renewed, remove camera for night vision
system - R212- ⇒ Communication; Rep. gr. 91 ; Night vision
system; Removing and installing camera for night vision sys‐
tem .
Installing
Tightening torques

camera for night vision system - R212- -
vehicles from model year 2015 onwards
Removing
– Unscrew bolts -1, 3, 5- and detach mounting -4- with camera
for night vision system - R212- .
– Release securing clip -6- -arrow- and disconnect fluid line.
– If mounting is to be renewed, remove camera for night vision
system - R212- ⇒ Communication; Rep. gr. 91 ; Night vision
system; Removing and installing camera for night vision sys‐
tem .
Installing
Tightening torques


for bumper cover (front) - Audi A6/S6
Removing
– Unscrew bolts -2, 4- and -arrows-.
– Detach closure plate -3- for bumper cover (front) towards rear
and move electrical wiring harness -1- clear.
– If fitted, move headlight washer fluid line clear.
– Detach closure plate for bumper cover.
Installing
Tightening torques
♦ ⇒ “1.1.3 Exploded view - bumper cover, lock carrier cover and
closure plate, Audi A6/S6”, page 220

for bumper cover (front) - Audi RS 6
Removing
– Unscrew bolts -2- and -arrows-.
– Detach closure plate -3- for bumper cover (front) towards rear
and move electrical wiring harness -1- clear.
– Detach closure plate for bumper cover.
Installing
Tightening torques
♦ ⇒ “1.1.6 Exploded view - bumper cover, lock carrier cover and
closure plate, Audi RS 6”, page 224

1.5.8 Removing and installing spoiler lip

Removing
– Remove closure plate for bumper cover (front) ⇒ page 239 .
Caution
Risk of damage to spoiler lip.

♦ Coat retaining tabs on spoiler lip with a small amount of
soap solution.
– Starting at outer edge, release retaining tabs -3- of spoiler lip

-1- -arrows-.
– Carefully pull spoiler lip out of spoiler mounting -2- and detach.
Installing
1.5.9 Removing and installing spoiler (bottom

section)
Removing
– Remove closure plate for bumper cover (front) ⇒ page 243 .
– Detach air duct for radiator (bottom).
– Starting at outer edge, pull bottom section of spoiler -1- off

bumper -arrow-.
Installing
Tightening torques
♦ ⇒ “1.1.5 Exploded view - bumper cover, Audi RS 6”,
page 222


spoiler (bottom section)
Removing
– Remove spoiler (bottom section) ⇒ page 244 .
– Pull mounting -1- slightly towards rear and move electrical wir‐
ing harness -2- clear.
– Detach mounting.
Installing
Tightening torques
page 222

mounting (front)
Removing
– Loosen bolt -2- three turns.
– Move electrical wiring harness -1- clear.
– Unscrew bolts -3 and 5- and detach bumper cover mounting
(front) -4-.
Note
Depending on version, nuts may be fitted instead of bolts.
Installing
Tightening torques
1.5.12 Removing and installing moulded foam

insert - Audi A6/S6 up to model year
2014

Removing
– Prise off retaining clip -1- using removal lever - 80-200- .
– Swivel out moulded foam insert -2- at bottom in direction of
-arrow- and disengage tabs -3- for moulded foam insert.
– Detach moulded foam insert.
Installing

insert - Audi A6 from model year 2015
onwards
Removing

– Prise off retaining clip -1- using removal lever - 80-200- .

– Guide moulded foam insert -2- out of retainer -3- and detach.
Installing

insert - Audi RS 6
Removing
– Swivel out moulded foam insert -1- at top in direction of
-arrow B-, release fastener -arrow A- and disengage moulded
foam insert.
– Detach moulded foam insert.
Installing

moulded foam insert - Audi RS 6
Removing
– Detach number plate.
– Unscrew bolts -2- and -3- on number plate holder -1-.
– Remove moulded foam insert ⇒ page 247 .


Installing
Tightening torques
page 222
1.5.16 Removing and installing cover for head‐

light washer jet
Removing
– Remove headlight washer jet ⇒ Electrical system; Rep. gr.
92 ; Headlight washer system; Removing and installing wash‐
er jets .
– Spread apart sides -2- of cover -1- for washer jet -arrows- us‐
ing a screwdriver and take out washer jet -3-.
Installing
– Insert washer jet -1- in cover -2- as shown in illustration and

press on in direction of -arrow- until it clicks into place.

1.5.17 Removing and installing air intake grille

Removing
– Pull air intake grille -1- off bumper cover -arrow-.
Installing
1.5.18 Removing and installing outer air intake

grille - Audi RS 6
Removing
– Press off binding clips -1, 5- and move electrical wiring har‐
ness -3- clear.
– Push fasteners -2, 4, 6, 7- slightly to one side -arrow- and press
cover -8- off bumper cover.

– Carefully press retaining clips -arrows- off guide lug using a

screwdriver.
– Detach trim -1- from bumper cover -2-.
– Release fasteners -1, 4, 5- -arrow- and pull air intake grille

-3- off bumper cover -2-.
Installing
1.5.19 Removing and installing inner air intake

grille - Audi RS 6
Removing
– Pull air intake grille -1- off bumper cover -arrow- and detach.
Note
If the air intake grille cannot be removed as described, the bumper

cover (front) must be removed ⇒ page 226 .
Installing
– Retaining tabs must engage fully in bumper.

1.5.20 Removing and installing bracket for am‐

bient temperature sensor - G17-
Removing
– Remove ambient temperature sensor - G17- ⇒ Electrical sys‐
tem; Rep. gr. 90 ; Dash panel insert; Removing and installing
ambient temperature sensor .
– Press out spreader pin -2- and detach bracket -1-.
Installing

2 Bumper (rear)
⇒ “2.1 Exploded view - bumper cover”, page 252
⇒ “2.2 Exploded view - impact bar”, page 260
⇒ “2.3 Removing and installing bumper cover”, page 264
⇒ “2.4 Removing and installing impact bar”, page 268
⇒ “2.5 Removing and installing cable mounting bracket”,
page 270
⇒ “2.6 Removing and installing attachments”, page 271
2.1 Exploded view - bumper cover
Caution
On vehicles with lane change assist, lane change assist control

unit -J769- / -J770- must be re-calibrated ⇒ Electrical system;
Rep. gr. 96 ; Lane change assist; Calibrating lane change as‐
sist .
⇒ “2.1.1 Exploded view - bumper cover, Audi A6/allroad/S6 up to

⇒ “2.1.2 Exploded view - bumper cover, Audi A6 from model year
⇒ “2.1.3 Exploded view - bumper cover, Audi RS 6”, page 258
2.1.1 Exploded view - bumper cover, Audi A6/allroad/S6 up to model year 2014

1 - Base plate for bumper cov‐

er
logue
⇒ page 271
2 - Bolt
❑ 8x
❑ 2.2 Nm
3 - Bumper cover (rear)
⇒ page 264
4 - Bolt
❑ Depending on equip‐
ment
❑ 2.1 Nm
5 - Mounting (side)
⇒ page 273
6 - Bolt
❑ 2x
❑ Tightening sequence
⇒ page 255
7 - Bolt
❑ 2x
⇒ page 255
8 - Mounting (top)
9 - Locating pin
❑ For securing bumper cover (rear) to mounting (top)
10 - Bolt
❑ 2x
❑ Tightening torque ⇒ Electrical system; Rep. gr. 96 ; Lane change assist; Overview - lane change assist
11 - Lane change assist control unit
❑ Removing and installing ⇒ Electrical system; Rep. gr. 96 ; Lane change assist; Removing and installing
lane change assist control unit -J769- / -J770-
12 - Outer mounting
13 - Bolt
❑ Saloon: 3x
❑ Avant: 2x
❑ Tightening sequence ⇒ page 254
14 - Bolt/nut
❑ Saloon: bolt
2. Bumper (rear) 253

❑ Avant: nut
15 - Centre mounting
16 - Bolt
❑ 4x
17 - Bolt
❑ 2x
18 - Bolt
❑ 2.5 Nm
19 - Cover
❑ For towing eye
20 - Trim strip
❑ For base plate for bumper cover
❑ Depending on equipment version
21 - Bolt
❑ Vehicles without towing bracket: 3x
❑ Vehicles with towing bracket: 2x
❑ 1.7 Nm
Outer bumper cover mounting - tightening torque and sequence

– Tighten bolts/nut in specified sequence.
Bolt/nut Torque
Bolt -item 1- 3 Nm
Bolt -item 2- 3 Nm
Bolt -item 3- 3 Nm
Nut -item 3- 2.2 Nm
Bumper cover mounting (top) - tightening torque and sequence

– Tighten bolts to 1.5 Nm in sequence -1, 2-.

Bumper cover mounting (centre) - tightening torque and se‐

quence
– Tighten bolts to 3 Nm in sequence -1 … 4-.
Bumper cover mounting (side) - tightening torque and sequence
Note
Note different versions of bolts.
– Tighten bolts in specified sequence.

Bolt Torque
-Item 1- 1.5 Nm
-Item 2- 1.5 Nm
-Item 3- 3 Nm
-Item 4- 3 Nm
2.1.2 Exploded view - bumper cover, Audi A6 from model year 2015 onwards

1 - Trim
❑ Bottom
❑ e-tron only
⇒ page 278
2 - Trim
❑ Top
❑ e-tron only
⇒ page 278
3 - Bolt
❑ 2x
❑ 4.5 Nm
4 - Bolt
❑ 2x
❑ 1.7 Nm
5 - Base plate for bumper cov‐
er
logue
⇒ page 271
7 - Mounting (rear)
⇒ page 273
⇒ page 265
9 - Mounting
❑ For tailpipe trim
10 - Bolt
❑ 4x
❑ 2 Nm
11 - Tailpipe trim
12 - Bolt
❑ 2x
❑ 2 Nm
13 - Mounting (side)
14 - Bolt
❑ 2x

15 - Bolt
❑ 2x
16 - Mounting (top)
17 - Locating pin
18 - Bolt
❑ 2x
20 - Outer mounting
21 - Bolt
❑ Saloon: 3x
❑ Avant: 2x
22 - Bolt/nut
❑ Saloon: bolt
❑ Avant: nut
24 - Bolt
❑ 4x
25 - Bolt
❑ 2.5 Nm
26 - Cover
❑ For towing eye
27 - Nut
❑ 2x
❑ 1.5 Nm
28 - Base plate for bumper cover
❑ e-tron only
29 - Trim strip
❑ e-tron only

Bumper cover mounting (centre) - tightening torque and se‐

quence
2.1.3 Exploded view - bumper cover, Audi RS 6

⇒ page 264
2 - Bolt
❑ 2.5 Nm
3 - Mounting
❑ For tailpipe trim
⇒ page 279
4 - Bolt
❑ 4x
❑ 2 Nm
5 - Tailpipe trim
⇒ page 278
6 - Bolt
❑ 3x
❑ 2 Nm
7 - Bolt
❑ 2x
⇒ page 255
8 - Bolt
❑ 2x
⇒ page 255
9 - Mounting (side)
⇒ page 273
10 - Mounting (top)
11 - Locating pin

12 - Bolt
❑ 2x
13 - Bolt
❑ 2x
❑ Tightening torque ⇒ Electrical system; Rep. gr. 96 ; Lane change assist; Overview - lane change assist
15 - Outer mounting
16 - Nut
17 - Bolt
❑ 2x
18 - Outer mounting (bottom)
19 - Bolt
20 - Nut
22 - Bolt
❑ 4x
23 - Base plate for bumper cover
24 - Cover
❑ For towing eye
25 - Bolt
❑ 3x
❑ 1.7 Nm

Outer bumper cover mounting - tightening torque and sequence

– Tighten bolts/nut in specified sequence.
Bolt/nut Torque
Bolt -item 1- 3 Nm
Bolt -item 2- 3 Nm
Nut -item 3- 2.2 Nm
Bolt -item 4- 1.5 Nm
Nut -item 5- 2.2 Nm
2.2 Exploded view - impact bar

⇒ “2.2.1 Exploded view - impact bar, Audi A6/allroad/S6”,
page 260
⇒ “2.2.2 Exploded view - impact bar, Audi RS 6”, page 263
2.2.1 Exploded view - impact bar, Audi A6/allroad/S6

1 - Bolt
❑ 3x
❑ 3.5 Nm
2 - Grommet
❑ For cable
3 - LED indicator lamp
❑ Indicates whether tow‐
ing bracket is locked
properly
Rep. gr. 96 ; Towing
bracket; Removing and
installing LED warning
lamp
4 - Mounting
❑ For cable
⇒ page 270
5 - Bolt
❑ 3x
❑ 2 Nm
6 - Bolt
❑ 3x
⇒ page 262
7 - Foam seal
8 - Nut
❑ 23 Nm + 90°
9 - Impact bar
❑ For vehicles without towing bracket
10 - Pull knob
❑ For releasing towing bracket
❑ Removing and installing ⇒ “2.5 Removing and installing cable mounting bracket”, page 270
11 - Locking clip
❑ For pull knob
12 - Speed nut
❑ 3x
13 - Bolt
❑ 4x
14 - Impact bar
❑ For vehicles with towing bracket

15 - Socket
❑ Removing and installing ⇒ Electrical system; Rep. gr. 96 ; Cigarette lighter, socket
❑ Pin assignment ⇒ Electrical system; Rep. gr. 96 ; Cigarette lighter, socket
Impact bar without towing bracket - tightening torque and se‐

quence
Impact bar with towing bracket - tightening torque and sequence

– Tighten bolts to 50 Nm +90° further in sequence -1 … 4-.

2.2.2 Exploded view - impact bar, Audi RS 6

⇒ page 280
2 - Bolt
❑ 3x
❑ Tightening sequence ⇒
Running gear, axles,
steering; Rep. gr. 43 ;
Dynamic Ride Control
(DRC); Exploded view -
central valve
3 - Central valve
❑ For electronically con‐
trolled damping
⇒ Running gear, axles,
steering; Rep. gr. 43 ;
Dynamic Ride Control
(DRC); Removing and
installing central valve
4 - Impact bar
⇒ page 268
5 - Bolt
❑ 3x
⇒ page 262
6 - Foam seal
7 - Nut
❑ 23 Nm + 90°
❑ For central valve
9 - Bolt
❑ 3x
❑ Tightening sequence ⇒ Running gear, axles, steering; Rep. gr. 43 ; Dynamic Ride Control (DRC);
Exploded view - central valve

2.3 Removing and installing bumper cover

⇒ “2.3.1 Removing and installing bumper cover - vehicles up to
⇒ “2.3.2 Removing and installing bumper cover - vehicles from
model year 2015 onwards”, page 265
⇒ “2.3.3 Gap widths at bumper cover”, page 267
2.3.1 Removing and installing bumper cover -

vehicles up to model year 2014
Caution

sist .
Removing
– Unscrew bolts -1, 2, 3- from side sections of bumper cover
-4-.
– Detach cover for luggage compartment side trim.

– Vehicles with towing bracket: Remove cable mounting brack‐
et; leave cable inserted ⇒ page 270 .
– If fitted, unplug electrical connector -1- at parking aid control
unit - J446- , cut through cable tie and move wiring harness
clear at bracket for control units -arrow-.
– If fitted, unplug electrical connector for rear lid power opening
control unit - J938- .
– Push grommet -2- through to outside.

– Remove outer tail lights ⇒ Electrical system; Rep. gr. 94 ; Tail

light cluster; Removing and installing tail light cluster .
– Pull out locating pin -1- upwards and release securing clip
-2-.
– Disengage side sections at side panel outwards -arrow A-.
– Pull bumper cover -4- (centre) towards rear out of fasteners
-arrow B-.
– If fitted, electrical wiring harness must be routed out through
body opening.
– Detach bumper cover and set it down on a soft surface.
Installing
– Adhesive pad ⇒ Audi Paintwork manual
Tightening torques
2.3.2 Removing and installing bumper cover -

Caution

sist .
Removing
– Unscrew bolts -1, 2, 3- from side sections of bumper cover
-4-.

– Detach cover for luggage compartment side trim.

– Remove outer tail lights ⇒ Electrical system; Rep. gr. 94 ; Tail

light cluster; Removing and installing tail light cluster .
– Pull out locating pin -1- upwards and release securing clip
-2-.
– Release retaining strip -1- from mounting at side -arrow A-.

– Disengage side sections at side panel outwards -arrow B-.
– Pull bumper cover -2- (centre) towards rear out of fasteners
-arrow C-.
– Guide electrical wiring harness out through body opening.
– Detach bumper cover and set it down on a soft surface.
Installing
– Adhesive pad ⇒ Audi Paintwork manual

– Check all adjuster elements -2-; it must be possible to turn

adjuster nut -1- easily -arrows-.
– Completely screw down adjuster nuts, but do not tighten.
– Move bumper cover into installation position.
– Tighten bolts.
Note
When tightening the bolt, the nuts of the adjuster element auto‐
matically turn towards the mounting point of the bumper cover to
lock it in place.
Tightening torques
♦ ⇒ “2.1.2 Exploded view - bumper cover, Audi A6 from model
year 2015 onwards”, page 255
2.3.3 Gap widths at bumper cover
A - Bumper cover (rear) to bot‐

tom of rear lid
• Gap width -a- = 5.0 mm
-1- Bumper cover
-2- Rear lid
B - Bumper cover (rear) to side

of rear lid
• Gap width -b- = 3.5 mm
-1- Bumper cover
-2- Rear lid
C - Bumper cover (rear) to out‐

er tail light
• Gap width -c- = 2.5 mm
-1- Bumper cover
-3- Outer tail light
D - Bumper cover (rear) to side

panel (rear)
• Gap width -d- = zero-gap
panel joint
-1- Bumper cover
-4- Side panel (rear)
E - Bumper cover (rear) to

bumper cover (bottom section)
• Gap width -e- = 1.0 mm
-1- Bumper cover
-5- Base plate for bumper cover

2.4 Removing and installing impact bar

⇒ “2.4.1 Removing and installing impact bar - vehicles without
towing bracket, Audi A6/allroad/S6”, page 268
⇒ “2.4.2 Removing and installing impact bar - Audi RS 6”,
page 268
⇒ “2.4.3 Removing and installing impact bar - vehicles with towing
bracket”, page 269
2.4.1 Removing and installing impact bar - ve‐

hicles without towing bracket, Audi A6/
allroad/S6
Removing
– Remove bumper cover (rear) ⇒ page 264 .
– If fitted, remove lining for spare wheel well ⇒ General body
repairs, interior; Rep. gr. 70 ; Luggage compartment trim pan‐
els; Removing and installing lining for spare wheel well .
– Unscrew nut -2- and bolts -1, 4, 5-.
– Detach impact bar -3-.
Installing
Note
Renew nuts which are tightened by turning through a specified

angle.
Tightening torques
♦ ⇒ Fig. ““Impact bar without towing bracket - tightening torque
and sequence”“ , page 262
2.4.2 Removing and installing impact bar - Au‐

di RS 6
Removing
– Remove outer bumper cover mounting ⇒ page 272 .
– Tie up retaining bracket -1- with central valve to one side.

– Remove lining for spare wheel well ⇒ General body repairs,

interior; Rep. gr. 70 ; Luggage compartment trim panels; Re‐
moving and installing lining for spare wheel well .
– Unscrew nut -2- and bolts -1, 4, 5-.
– Detach impact bar -3-.
Installing
Note
Renew nuts which are tightened by turning through a specified

angle.
Tightening torques
♦ ⇒ Fig. ““Impact bar without towing bracket - tightening torque
2.4.3 Removing and installing impact bar - ve‐

hicles with towing bracket
Removing
– Remove cable mounting bracket ⇒ page 270 .
– If fitted, remove lining for spare wheel well ⇒ General body
repairs, interior; Rep. gr. 70 ; Luggage compartment trim pan‐
els; Removing and installing lining for spare wheel well .
– Unplug electrical connector -1- and detach mounting -2-.

– Pull out impact bar -3- together with a second person.

– Pull off grommet -2- and guide out cable -1-.
Installing
Note
After fitting a new impact bar, the locking pin on the cable coupling
must be pulled off and the hole must be sealed using the self-
adhesive protective film supplied.
Tightening torques
Caution
Bolts which are tightened to a specified angle must be re‐

newed.
• Tightening torque ⇒ page 262

– Install trailer socket ⇒ Electrical system; Rep. gr. 96 ; Towing
bracket; Trailer socket .
2.5 Removing and installing cable mounting

bracket
WARNING

Removing
– Remove luggage compartment side trim ⇒ General body re‐
pairs, interior; Rep. gr. 70 ; Luggage compartment trim panels;
Removing and installing luggage compartment side trim .
– Pull out knob -6- at mounting bracket -3- and prise off locking
clip -5- using a small screwdriver -arrow-.
– Remove cable -4- from pull knob.
– Press cable support bracket -1- out of mounting bracket -3-

-arrow-.
– Unplug electrical connector -2- and detach mounting bracket.
Installing
Tightening torque
♦ ⇒ “2.2.1 Exploded view - impact bar, Audi A6/allroad/S6”, page
260

2.6 Removing and installing attachments

⇒ “2.6.1 Removing and installing outer bumper cover mounting -
Audi A6/S6”, page 271
⇒ “2.6.2 Removing and installing outer bumper cover mounting -
Audi RS 6”, page 272
⇒ “2.6.3 Removing and installing bumper cover mounting (top)”,
page 272
⇒ “2.6.4 Removing and installing bumper cover mounting (cen‐
tre)”, page 273
⇒ “2.6.5 Removing and installing bumper cover mounting (rear)”,
page 273
⇒ “2.6.6 Removing and installing bumper cover mounting (side)”,
page 273
⇒ “2.6.7 Removing and installing bumper cover (bottom section)
- Audi A6”, page 274
- Audi allroad”, page 275
- Audi RS 6”, page 275
⇒ “2.6.10 Removing and installing trim strip for bumper cover
(bottom section)”, page 276
⇒ “2.6.11 Removing and installing bumper cover trim - e-tron”,
page 278
⇒ “2.6.12 Removing and installing tailpipe trim - Audi RS 6”, page
278
⇒ “2.6.13 Removing and installing tailpipe trim - vehicles from
⇒ “2.6.14 Removing and installing mounting for tailpipe trim - Audi
RS 6”, page 279
⇒ “2.6.15 Removing and installing mounting for tailpipe trim - ve‐
hicles from model year 2015 onwards”, page 280
⇒ “2.6.16 Removing and installing moulded foam insert”,
page 280
2.6.1 Removing and installing outer bumper

cover mounting - Audi A6/S6
Removing

– If fitted, unplug electrical connector -1-.

– Unscrew bolts -arrows- and detach outer bumper cover
mounting -2-.
Note
Depending on equipment, a nut may be fitted instead of the lower

bolt.
Installing
– On vehicles with lane change assist, lane change assist con‐
trol unit -J769- / -J770- must be re-calibrated ⇒ Electrical
system; Rep. gr. 96 ; Lane change assist; Calibrating lane
change assist .
Tightening torques
♦ ⇒ Fig. ““Outer bumper cover mounting - tightening torque and
sequence”“ , page 254
2.6.2 Removing and installing outer bumper

cover mounting - Audi RS 6
Removing
– If fitted, unplug electrical connector -2-.
– Unscrew bolts -3- and nuts -1, 5- and detach outer bumper
cover mounting -4-.
Installing
– On vehicles with lane change assist, lane change assist con‐
trol unit -J769- / -J770- must be re-calibrated ⇒ Electrical
system; Rep. gr. 96 ; Lane change assist; Calibrating lane
change assist .
Tightening torques
♦ ⇒ Fig. ““Outer bumper cover mounting - tightening torque and

mounting (top)
Removing

– Unscrew bolts -1 and 3- and detach bumper cover mounting

(top) -2-.
Installing
Tightening torques
♦ ⇒ Fig. ““Bumper cover mounting (top) - tightening torque and

mounting (centre)
Removing
– Detach mounting (centre) -1-.
Installing
Tightening torques
♦ Vehicles up to model year 2014
⇒ Fig. ““Bumper cover mounting (centre) - tightening torque
♦ Vehicles from model year 2015 onwards
⇒ Fig. ““Bumper cover mounting (centre) - tightening torque

mounting (rear)
Removing
– Remove nuts -1, 2-.
– Detach mounting (rear) -3-.
Installing
Tightening torques

mounting (side)
Removing


– Remove bumper cover mounting (side) -1-.
Installing
Tightening torques
♦ ⇒ Fig. ““Bumper cover mounting (side) - tightening torque and

(bottom section) - Audi A6
Removing
– Vehicles up to model year 2014: Unscrew bolts -arrows- in
bumper cover (bottom section).
– Vehicles from model year 2015 onwards: Unscrew bolts

-arrows- in bumper cover (bottom section).

– Carefully release securing tab -3- in direction of -arrow A-, and

at the same time pull retaining clip out of bumper cover -1- by
pulling on bottom section of bumper cover -2-.
• Disengage bumper cover (bottom section) from outside
-arrow B- towards centre of vehicle -arrow C-.
Installing
– Clip bumper cover (bottom section) into bumper cover until it
engages audibly.

(bottom section) - Audi allroad
Removing
– Bumper cover removed ⇒ page 264
– Bend open metal fasteners -arrows a- on bumper cover.
– Release fasteners -arrows b- one by one and pull bumper
cover (bottom section) out of bumper cover.
Installing
– When installing, bumper cover (bottom section) must be clip‐
ped into bumper cover until it engages audibly.
– Metal fasteners must be bent so they engage behind bumper
cover.

(bottom section) - Audi RS 6
Removing
– Remove mounting for tailpipe trim ⇒ page 279 .

– On vehicles with automatic rear lid opening, unplug electrical

connector -1-.
– Take rear lid power opening senders -3, 4- out of clips
-arrows-.
– Release fastener -2- -arrow- and at the same time pull bottom
section -1- off bumper cover -3-.
Installing
– Clip bumper cover (bottom section) into bumper cover until it
engages audibly.
2.6.10 Removing and installing trim strip for

bumper cover (bottom section)
Removing and installing trim strip for bumper cover (bottom sec‐
tion) ⇒ page 276
tion) - e-tron ⇒ page 277
tion)
Removing


– Detach trim strip -1- from bottom section of bumper cover -2-
-arrow-.
Installing
Tightening torques
♦ ⇒ “2.1.1 Exploded view - bumper cover, Audi A6/allroad/S6 up
to model year 2014”, page 252
tion) - e-tron
Removing
– Remove base plate for bumper cover ⇒ page 274 .
– Disengage catches -arrows-.
– Detach trim strip -2- from bottom section of bumper cover
-1-.
Installing


trim - e-tron
Removing
– Remove trim strip for bumper cover (bottom section)
⇒ page 277 .
– Release fasteners -arrows- and pull trim (top) -2- off bumper
cover (bottom section) -1-.
– Release fasteners -arrows- and pull trim (bottom) -1- off bump‐
er cover (bottom section) -2-.
Installing
2.6.12 Removing and installing tailpipe trim -

Audi RS 6
Removing


– Detach tailpipe trim -1- inwards from bumper cover.
Installing
– Check distance between tailpipe trim -2- and bumper cover

-1-:
• Dimension -x- = even gap all around
Tightening torques
page 258
2.6.13 Removing and installing tailpipe trim -

Removing
– Detach tailpipe trim -1- inwards from mounting -3-.
Installing
Tightening torques

tailpipe trim - Audi RS 6
Removing

– Right-side: On vehicles with automatic rear lid opening, unplug

electrical connectors -2, 3-.
– Move electrical wiring harness -1- clear.
– Carefully press retaining clips -arrows- off guide lugs using a

screwdriver.
– Detach mounting -3- from bumper cover.
Installing
Tightening torques
page 258

tailpipe trim - vehicles from model year
2015 onwards
Removing
– Detach mounting -1- from bumper cover.
Installing
Tightening torques

insert
Removing

– Release retaining tab (bottom) -3- in direction of -arrow A- and

lift off moulded foam insert -1- -arrow B-; this disengages re‐
taining tabs (top) -2-.
Installing

64 – Glazing
1 Repair notes
⇒ “1.1 Minimum drying times for bonded windows”, page 282
⇒ “1.2 Repairing windows”, page 283
⇒ “1.3 Notes on installing flush-bonded windows”, page 283
⇒ “1.4 Preparing undamaged windows for installation”,
page 286
⇒ “1.5 Preparing new windows for installation”, page 287
⇒ “1.6 Preparing body flange for installation”, page 288
⇒ “1.7 Cleaning off adhesive sealant”, page 289
⇒ “1.8 Re-sealing windows”, page 289
1.1 Minimum drying times for bonded win‐

dows
WARNING
♦ For safety reasons, only use non-conductive 2-compo‐

nent adhesive with the designations listed below when
installing windscreen and rear window.
♦ You must NOT drive the vehicle until the minimum drying
time has elapsed, as the vehicle is otherwise not safe to
drive.
Window Vehicle Adhesive sealant Minimum

drying time
(in hours)
Windscreen With 2-component win‐ 2
airbag dow adhesive set -
D 004 660 M2-
Rear window 2-component win‐ 2
dow adhesive set -
D 004 660 M2-
Side windows 1-component win‐ 3
dow adhesive - DH
009 100 03-
Cleaning off adhesive sealant
We recommend using adhesive remover D 002 000 10 for clean‐
ing. Observe safety precautions when handling.
WARNING
When cleaning from inside the vehicle passenger compart‐

ment, make sure you do not exert outward pressure on the
window you have just fitted.
Painted surfaces
– First clean painted surface with a dry cloth. Then clean off any
residual dirt using adhesive remover D 002 000 10.
282 Rep. gr.64 - Glazing

Plastic trim panel

– Allow adhesive sealant to dry (approx. 1 hour) and then pull
off.
1.2 Repairing windows

♦ Windscreen repair kit - VAS 1993- or -VAS 6092-
Note
♦ Windscreens damaged by stone chipping can be repaired us‐

ing windscreen repair kit - VAS 6092- and resin, Talon - VAS
1993/2- .
♦ The damaged areas must not exceed a certain size and area,
and must not be within the main field of vision.
♦ For detailed information, refer to the instructions supplied with
each kit.
1.3 Notes on installing flush-bonded win‐

dows
♦ Removal kit for flush bonded windows - VAS 6452-
1. Repair notes 283

♦ Wire reel - VAS 6452/1-
♦ Wire for removal kit - VAS 6452/2-

♦ Cutting tool - V.A.G 1351-
♦ Pull handle - V.A.G 1351/1-

♦ Suction lifter - V.A.G 1344-
♦ Electric cutter - V.A.G 1561A-

♦ Blade, offset - V.A.G 1561/10-
♦ Universal blade - V.A.G 1561/11-
♦ Scraper (15 + 25 mm) - V.A.G 1561/7+8-
♦ Double cartridge gun - VAS 5237-
1. Repair notes 285

♦ Hand-cartridge gun - V.A.G 1628-
♦ Cartridge heater - V.A.G 1939A-
Materials
♦ 2-component window adhesive set - D 004 660 M2- 1)
♦ 1-component window adhesive - DH 009 100 03- 4)
♦ Glass/paint primer - D 009 200 02-
♦ Applicator - D 009 500 25-
♦ Adhesive remover - D 002 000 10-
♦ Cutting wire - 6452/2- / cutting cord - 357 853 999-
1) Note minimum drying time ⇒ page 282 .

2) To process this material use double cartridge gun - VAS 5237- .
3) Heat using cartridge heater - V.A.G 1939 A- according to manufacturer's instructions.
4) Small 110 ml cartridge for sealing and/or for use when the 400 ml double cartridge is not sufficient.
1.4 Preparing undamaged windows for in‐

stallation
– Just before re-installing an undamaged window, use electric
cutter - V.A.G 1561 A- and scraper (25 mm) - V.A.G 1561/8-
to cut back the remaining adhesive sealant on the window and
flange to give a smooth surface, but do NOT remove com‐
pletely.

Note
The remaining material serves as a bonding surface when apply‐

ing the new adhesive sealing material.
Caution
♦ Bonding surface must be free of dirt and grease.

♦ Do not trim bonding surface until shortly before installa‐
tion.
♦ Do not apply primer to bonding surface and do not use
cleaning solution.
1.5 Preparing new windows for installation

– Clean all around bonding surface with cleaning solution - D
009 401 04- .
– Wipe clean surface with a dry, lint-free paper towel.
– Apply glass/paint primer - D 009 200 02- as described below.
WARNING
• The ceramic coating on new windows is not a primer.

• The glass must always be primed before applying adhe‐
sive sealant.
• The glass/paint primer is conductive and must not come
into contact with the bus bar, e.g. of the rear window heat‐
ing.
Applying primer:
– Use applicator -2- to apply glass/paint primer -3- evenly and
in one movement onto window -4- beside moulding -1-.
– Start application with fully soaked felt.
• Primer width approx. 20 mm
• Apply glass/paint primer centrally in relation to adhesive bead.
• Flash-off time: 10 minutes
Applying adhesive
Note
The cross-section of the adhesive bead is determined by the size

of the applicator nozzle opening and the rate of application.
1. Repair notes 287

Dimensions for applying adhesive:

1- Adhesive bead
2- Glass/paint primer
3- Window glass
• Dimension -a- = 8 mm
• Dimension -b- = 12 mm
• Dimension -c-: note different distances from edge of wind‐
screen ⇒ Item 2 (page 290) .
– Apply full surface of nozzle -2- to glass.

• Direction of application -arrow- for adhesive bead -1-.
– Apply adhesive sealant -1- all around glass -2-, as shown.

– Windscreen or rear window glass must be installed in opening
using two suction lifters.
Caution
The glass must be fitted within 15 minutes; otherwise the ad‐

hesive properties of the adhesive sealant will be impaired.
1.6 Preparing body flange for installation
WARNING
Bonding surface must be free of dirt and grease.
– Shortly before installing the window, cut back the remaining

adhesive sealant on the body flange with a carpet knife, but
do not remove it completely.

Note
The remaining sealant is required as a base for better adhesion

of the new adhesive sealant.
– If window flange has been damaged, paintwork structure must

be repaired and, if necessary, anti-corrosion measures must
be taken ⇒ Audi Paintwork Guide .
– Clean repaired area using cleaning solution - D 009 401 04-
and then apply glass/paint primer - D 009 200 02- .
1.7 Cleaning off adhesive sealant

We recommend using adhesive remover - D 002 000 10- for
cleaning. Observe safety precautions when handling.
WARNING
When cleaning from inside the vehicle passenger compart‐

ment, make sure you do not exert outward pressure on the
window you have just fitted.
Painted surfaces
– First clean painted surface with a dry cloth. Then clean off re‐
maining adhesive sealant with adhesive remover - D 002 000
10- .
Plastic trim panel
– Allow adhesive sealant to dry (approx. 1 hour) and then pull
off.
1.8 Re-sealing windows

– Allow leaking area to dry and then clean.
– Apply and spread adhesive sealant in leaking area between
window and metal flange.
– Allow adhesive sealant to harden.
– Perform leak test with water.
– Carry out visual inspection from passenger compartment.
1. Repair notes 289

2 Windscreen
⇒ “2.1 Exploded view - windscreen”, page 290
⇒ “2.2 Removing and installing windscreen”, page 291
2.1 Exploded view - windscreen
1 - Windscreen
❑ Distance from roof: di‐
mension -a- = 2 mm
❑ Align centrally between
A-pillars
2 - Adhesive bead
❑ Note minimum drying
time ⇒ page 282 .
• Dimension -b- = 17 mm
± 2 mm
• Dimension -c- = 10 mm
± 2 mm
• Dimension -d- = 8 mm
± 2 mm
3 - Trim cover
4 - Water deflector strip
5 - Surround for plenum cham‐
ber cover
placement part
❑ With a new windscreen,
the protective beading
must be pulled out be‐
fore fitting the plenum
chamber cover.
6 - Plenum chamber cover
❑ Allow window adhesive
to dry (minimum:
3 hours) before pressing
plenum chamber cover
into retaining strip.

Assigning windscreen to front camera for driver assist systems -

R242-
Before ordering a new windscreen, the version must be deter‐
mined on vehicles equipped with front camera for driver assist
systems - R242- :
-A- Retaining plate for front camera for driver assist
systems - R242- , old version ⇒ Assign old wind‐
screen version
-B- Retaining plate for front camera for driver assist
systems - R242- , new version ⇒ Assign new wind‐
screen version
Removing protective beading

– Before fitting plenum chamber cover -4- when new windscreen
-1- is installed, protective beading -2- must be removed from
surround -3-.
2.2 Removing and installing windscreen

⇒ “2.2.1 Removing and installing windscreen”, page 291
⇒ “2.2.2 Renewing trim cover”, page 295
2.2.1 Removing and installing windscreen
Caution
♦ On vehicles with front camera for driver assist systems,

the camera must be re-calibrated ⇒ Running gear, axles,
steering; Rep. gr. 44 ; Front camera for driver assist sys‐
tems; Calibrating front camera for driver assist systems .
♦ After renewing the windscreen, the control unit for head-
up display - J898- must be re-calibrated on vehicles with
head-up display ⇒ Electrical system; Rep. gr. 90 ; Dash
panel insert; Calibrating control unit for head-up display .
– Remove wiper arms ⇒ Electrical system; Rep. gr. 92 ; Wind‐

screen wiper system; Removing and installing wiper arms .
– Remove cowl panel trim ⇒ page 22 .
– Remove sun visors (left, right and centre) ⇒ General body
repairs, interior; Rep. gr. 68 ; Equipment; Exploded view - sun
visors .
– Remove interior mirror ⇒ General body repairs, interior; Rep.
gr. 68 ; Interior mirror; Removing and installing interior mirror .
2. Windscreen 291
– Remove A-pillar trim (top left and right) ⇒ General body re‐
pairs, interior; Rep. gr. 70 ; Passenger compartment trim
panels; Removing and installing A-pillar trim .
WARNING
Always wear safety goggles and leather gloves when removing

windscreen.
– Use wire reel - VAS 6452/1- to reel off about 6.5 metres of
cutting wire (corresponding to 6 turns) and cut off.
– Mask over body flange with adhesive tape -1- to avoid damage
where awl is pushed through at the bottom.
– Pierce adhesive bead in this area with awl from inside to out‐
side, as shown.
– Thread both ends of cutting wire -3- into awl -2- and pull
through to the inside.
– Position cutting wire under glass all around windscreen, as

shown.
Caution
The wire ends must not be twisted at the point where they pass
through the adhesive bead -arrow-.
– Attach both reels to inside of glass, as shown.

– Insert end of cutting wire -1- into reel -2-.
– Tension cutting wire and insert protective film -2- between

dash panel and wire.
– Cut clear the first area. While doing so, wire is guided into in‐
tegrated idler pulley -arrow- on reel.
– Additionally insert guide awl -2- into adhesive bead, as shown,

and attach it to windscreen using suction pad so that wire runs
along windscreen as close to the glass as possible.
– Adjust protective film -3- as necessary with length of wire and
continue cutting clear using reel -1-.
2. Windscreen 293
– Adjust reel and guide awl as shown, and cut clear area at A-
pillar.
– Adjust reel and guide awl to approx. centre of windscreen, as
shown.
– Cut windscreen clear approx. to centre.
– Use second reel to cut bottom area of windscreen clear.
– Move reel up and insert guide awl, as shown.

– Cut windscreen clear upwards along A-pillar.
– Adjust reel over centre of windscreen and adjust first reel as

shown and cut windscreen fully clear at top.
– Lift windscreen out of vehicle using two suction lifters.
Installing
– Fitting instructions ⇒ page 283
– Prepare undamaged glass for installation ⇒ page 286 .
– Prepare new glass for installation ⇒ page 287 .
– Prepare body flange for installation ⇒ page 288 .
– Install windscreen glass in windscreen opening using two suc‐
tion lifters.
Caution

– Align glass so that spacing is equal on both sides.

• Distance from edge of windscreen to roof frame
• Secure windscreen to roof at top with adhesive tape.
– Pull protective strip -2- out of windscreen surround before fit‐
ting cowl panel trim.
– Note minimum drying time ⇒ page 282 .
2.2.2 Renewing trim cover
2. Windscreen 295
1 - Windscreen
❑ Removed
2 - Trim cover
– Bonding on
⇒ page 296 .
– Before fitting new trim

cover, use commercially
available glass scraper
to completely remove
remaining material, tak‐
ing care not to damage
black ceramic band.

using cleaning solution
D 009 401 04.
– Use soft pencil or similar

to make mark on inside
of windscreen at a dis‐
tance -a- = 8 mm from
top edge of windscreen.
– Prime bonding surface

with D 009 200 02 as far
as mark made earlier
and allow to flash off for
at least 10 minutes.
– Starting in centre, press

trim cover onto wind‐
screen in such a way
that rear edge aligns
with end of primed area
(pencil marking).
– Re-install windscreen.
Bonding on trim cover

– Windscreen -1- with ceramic band
– Clean bonding surface using cleaning solution D 009 041 04.
– Then make a marking at an even distance of -a- = 8 mm from
top edge of windscreen.
– Carefully apply glass/paint primer D 009 200 02 as far as
marking.
– Allow glass/paint primer to flash off for at least 10 minutes.
– Peel protective film off double-sided adhesive tape -3-.
– Press trim cover -2- centrally onto windscreen in such a way
that rear edge aligns with end of primed area (marking).
– Use roller to firmly press trim cover onto windscreen.

3 Rear window
⇒ “3.1 Exploded view - rear window”, page 297
⇒ “3.2 Removing and installing rear window”, page 299
3.1 Exploded view - rear window

⇒ “3.1.1 Exploded view - rear window, Saloon”, page 297
⇒ “3.1.2 Exploded view - rear window, Avant”, page 298
3.1.1 Exploded view - rear window, Saloon
Note
♦ The rear window is supplied with connections that are only

required if certain optional equipment is installed.
♦ Cut off any cables at that are not used directly at the connec‐
tions on the rear window.
1 - Rear window
❑ Distance -a- to brake
light = 3 mm
❑ Set distance -e- to side
frame = 3 mm (equal on
both sides).
❑ Prior to removal, unplug
all electrical connectors
and move contacts in‐
wards towards the cen‐
tre of the window and fix
in position with adhesive
tape.
2 - Trim cover
3 - Adhesive bead
• Width of bead =
8 mm ± 2 mm
• Height of bead
= 12 mm + 2 mm
❑ Distances measured
from edge of window to
centre of adhesive
bead:
♦ Dimension -b- = 14 mm
♦ Dimension -c- = 17 mm
♦ Dimension -d- = 10 mm
4 - Spacer
❑ Supplied together with
rear window
5 - Adhesive stopper strip
❑ Affix adhesive stopper
strip directly adjacent to bus bar for window heating at sides towards edge of window.
3. Rear window 297

6 - Bus bar
❑ For heated rear window
❑ Must not come into contact with window adhesive
Caution
♦ Window adhesive must not come into contact with bus bar
for window heating.
♦ The glass must be fitted within 15 minutes; otherwise the
adhesive properties of the adhesive sealant will be im‐
paired.

– Note distance to brake light = 3 mm.
3.1.2 Exploded view - rear window, Avant
1 - Rear window
❑ Dimension -e- =
3.5 mm; align to D-pil‐
lars at sides
❑ Dimension -c- = 2.5 mm;
rear window must be
aligned centrally to rear
window wiper shaft
2 - Roof spoiler
❑ Removed ⇒ page 331
3 - Adhesive bead
Note
Note differing distances from edge

of window.
❑ Dimension -a- = 8 mm
❑ Dimension -b- = 12 mm
❑ Dimension -d- = 44 mm
4 - Adhesive stopper strip
❑ Bond on at distance of
17 mm from edge of win‐
dow to outer edge
5 - High-level brake light
❑ Removed ⇒ Electrical
system; Rep. gr. 94 ;
High-level brake light;
high-level brake light
bulb

3.2 Removing and installing rear window

⇒ “3.2.1 Removing undamaged rear window - Saloon”,
page 299
⇒ “3.2.2 Removing undamaged rear window - Avant”, page 302
⇒ “3.2.3 Removing damaged rear window”, page 306
⇒ “3.2.4 Installing rear window”, page 306
⇒ “3.2.5 Renewing trim cover - Saloon”, page 306
3.2.1 Removing undamaged rear window -

Saloon
Procedure
– Unplug electrical connectors for heated rear window and win‐
dow aerial, move towards centre of window and secure with
adhesive tape.
WARNING

window.
– Position cutting wire under glass all round rear window, as

shown.
– Position cutting wire around rear window (under window), as
shown.
Caution
3. Rear window 299

– Tension cutting wire with reel -1- and insert plastic film -2- from
removal kit - VAS 6452- as protection between wire and rear
shelf.


and attach it to window using suction pad so that wire runs
along window as close to the glass as possible.
– Adjust reel and guide awl, as shown, and cut clear area on D-
pillar.
– Adjust reel and guide awl, as shown.
– Continue cutting window clear up to around its centre.
3. Rear window 301

– Cut window clear upwards along D-pillar.
– Adjust reel over centre of window and adjust via first reel as
shown and cut window fully clear at top.
– Remove window from window opening using suction lifters.
3.2.2 Removing undamaged rear window -

Avant
Procedure
– Rear lid trim removed ⇒ General body repairs, interior; Rep.
gr. 70 ; Luggage compartment trim panels; Removing and
installing rear lid trim (top)
– Roof spoiler removed ⇒ page 331
– Rear window wiper removed ⇒ Electrical system; Rep. gr.
92 ; Rear window wiper system; Removing and installing rear
window wiper motor - V12- .
dow aerial, move towards centre of window and secure with
adhesive tape.

WARNING

window.
– Position cutting wire under glass all round rear window, as

shown.
– Position cutting wire around rear window (under window), as
shown.
Caution
3. Rear window 303

– Tension cutting wire with reel -1- and insert plastic film -2- from
removal kit - VAS 6452- as protection between wire and win‐
dow.

and attach it to windscreen using suction pad so that wire runs
along windscreen as close to the glass as possible.
– Adjust reel and guide awl, as shown, and cut clear area on D-
pillar.

– Continue cutting window clear up to around its centre.
– Cut window clear upwards along D-pillar.
3. Rear window 305

– Adjust reel over centre of window and adjust via first reel as
shown and cut window fully clear at top.
– Lift window out of window opening using suction lifters.
3.2.3 Removing damaged rear window

Procedure
WARNING

window.
– Protect body and interior against damage from glass splinters.

– Remove glass fragments down to adhesive sealant.
dow aerial.
– Mask flange all around with fabric-backed adhesive tape.
– Cut through adhesive sealant (with glass fragments) in win‐
dow opening using electric cutter - V.A.G 1561A- and offset
blade - V.A.G 1561/10- (with roller stop).
3.2.4 Installing rear window

Procedure
– Fit rear window into window opening using suction lifters.
Caution


3.2.5 Renewing trim cover - Saloon

1 - Rear window
❑ Removed
2 - Trim cover
– Pull off trim cover all
around.
– Remove any residual

adhesive using a glass
scraper.

D 009 401 04- .
– Apply glass/paint primer

- D 009 200 02- to bond‐
ing surface and allow to
flash off for 10 minutes.
– Starting at top, press on

corners of trim cover.
– Gradually peel protec‐

tive film off trim cover
and press on with dis‐
tance -a- (top) and -b-
(sides) to edge of win‐
dow.
– Press trim cover on us‐

3. Rear window 307

4 Side windows
⇒ “4.1 Exploded view - rear side window”, page 308
⇒ “4.2 Removing and installing rear side window”, page 310
4.1 Exploded view - rear side window

⇒ “4.1.1 Exploded view - rear side window, Saloon”, page 308
⇒ “4.1.2 Exploded view - rear side window, Avant”, page 309
4.1.1 Exploded view - rear side window, Saloon
1 - Side window
❑ Roof trim strip and side
trim strip removed
❑ Trim panel for C-pillar
removed
❑ Remove window
⇒ page 310 .
❑ When installing a new
window, first insert win‐
dow with locating pin on
D-pillar, then press fully
into window opening
and engage locating
pins at C-pillar.
❑ If "old" window is re-in‐
stalled, window must be
secured in window
opening using adhesive
tape.
2 - Adhesive bead
3 - Roof trim strip
4 - Locating pin
placement part
❑ Is cut in two when win‐
dow is removed
5 - Side trim strip

4.1.2 Exploded view - rear side window, Avant
1 - Side window
❑ Prior to removal, detach
trim strip for side panel
-4- and pull roof trim
strip in area of D-pillar
sideways out of retain‐
ing clips.
2 - Centring pin
❑ Is cut in two when win‐
dow is removed.
3 - Adhesive bead
4 - Roof trim strip
❑ Unclip from retaining
clips in area of side win‐
dow
5 - Moulding for side window
placement part
❑ Visible area must not be
damaged.
6 - Trim strip for side panel
❑ Unclip from retaining
clips at side panel and
pull out of roof trim strip
4. Side windows 309

4.2 Removing and installing rear side win‐

dow
⇒ “4.2.1 Removing undamaged side window - Saloon”,
page 310
⇒ “4.2.2 Removing undamaged side window - Avant”,
page 311
⇒ “4.2.3 Removing damaged side window”, page 311
⇒ “4.2.4 Installing side window - Saloon”, page 312
⇒ “4.2.5 Installing side window - Avant”, page 312
4.2.1 Removing undamaged side window -

Saloon
Procedure
Caution
Use adhesive tape to protect paintwork of side panel and roof

in cutting area.
– Detach inner door seal in area of C-pillar and side window.

– Trim panel for C-pillar removed
– Roof trim strip removed
Caution
Do NOT bend roof trim strip.
– Route cutting wire around side window as shown in illustration.

– Secure ends X and Y in two pull handles of cutting tool - V.A.G
1351- .
– With gentle sawing motion, pull cutting wire towards front in
direction of -arrow A- and cut through adhesive bead at bottom
of side panel and at roof frame.
– This involves first cutting the locating pin at the back of the
window and then the adhesive bead.
– Then pull cutting wire downwards in direction of -arrow B-
through adhesive bead.
– Take window out of window opening.

4.2.2 Removing undamaged side window -

Avant
Procedure
WARNING
♦ To prevent paintwork damage when removing and instal‐

ling trim strip, always mask area beneath side window on
side panel with adhesive tape.
♦ Even a slightly bent roof trim strip is damaged and must
be renewed.
Vehicles with high-gloss version of roof trim strip:

– Roof trim strip and side trim strip removed
– Unclip roof trim strip from roof in area of side window.
Caution
Remove trim panels at C-pillar and D-pillar (top) and secure

aerial connections towards centre of window with adhesive
tape.
– Route cutting wire around side window as shown in illustration.

– Secure ends X and Y in two pull handles of cutting tool - V.A.G
1351- .
– Pull cutting wire to front in direction of -arrow A- with sawing
movements and cut through adhesive bead at bottom of side
panel and at roof frame.
– This involves first cutting the locating pin at the back of the
window and then the adhesive bead.
– Then pull cutting wire downwards in direction of -arrow B-
through adhesive bead.
– Take window out of window opening.
4.2.3 Removing damaged side window

Procedure
– Protect body and interior against damage from glass splinters.
– Mask flange all around with fabric-backed adhesive tape.
– Remove glass fragments down to adhesive sealant.
WARNING

window.
– Cut through adhesive sealant (with glass fragments) in win‐

dow opening using electric cutter - V.A.G 1561A- and offset
blade - V.A.G 1561/10- (with roller stop).
4. Side windows 311

4.2.4 Installing side window - Saloon

Procedure
Note
Use 1-component window adhesive - DH 009 100 03- (small car‐

tridge). If more than one window/glass has to be bonded, 2-
component window adhesive set - DA 004 600 A2- can also be
used.
– First press in new window with locating pin at D-pillar, then

insert in window opening and press locating pins into C-pillar.
– When installing windows without locating pin, align window
lengthwise at edge of side panel -arrow- and insert into window
opening.
– Secure window glass in position in window opening with ad‐
hesive tape (without locating pins).
– Install door seal at C-pillar.
4.2.5 Installing side window - Avant

Procedure
Note
Use 1-component window adhesive - DH 009 100 03- (small car‐

tridge). If more than one window/glass has to be bonded, 2-
component window adhesive set - DA 004 600 A2- can also be
used.
– Before installing side window, roof and side trim strips must be
installed.
– Insert side window with centring pins in window flange and
press into body as far as possible.
Note
Side windows without centring pins must be secured in body

opening with adhesive tape.

5 Door windows
⇒ “5.1 Exploded view - front door window”, page 313
⇒ “5.2 Exploded view - rear door window”, page 314
⇒ “5.3 Removing and installing front door window”, page 315
⇒ “5.4 Removing and installing rear door window”, page 316
5.1 Exploded view - front door window
1 - Front door
Note

⇒ page 116
3 - Stud
4 - Door window
Note

⇒ page 315
5 - Window regulator motor
⇒ page 118
6 - Bolt
❑ 6 Nm
7 - Bolt
❑ 3.5 Nm
8 - Cap
5. Door windows 313

5.2 Exploded view - rear door window
1 - Rear door
Note

⇒ page 168
3 - Door window
Note

⇒ page 316
4 - Stud
5 - Cap
❑ Lever off inner door pan‐
el
6 - Nut
motor - V26-
⇒ page 169
8 - Bolt
❑ 3x
9 - Nut

5.3 Removing and installing front door window

Removing
1 - Door window
❑ Remove cover for door
⇒ page 127 .
❑ Remove loudspeaker ⇒
Communication; Rep.
gr. 91 ; Sound system;
front bass loudspeakers
-R21- / -R23- .
– To remove, release
catches -arrow- from ac‐
tuator -2- using a screw‐
driver and pull window
-1- up slightly in window
guide.
– Tilt window towards

front and pull it upwards,
out of door.
❑ Window regulator re‐
mains installed in door.
Releasing door window

– Use screwdriver or similar tool to press actuator -3- outwards
through opening in window guide -1- and hole in door window
-2- in order to release actuator.
– Pull window upwards out of actuator.
– Tilt window diagonally forwards and pull upwards out of win‐
dow guide.
5. Door windows 315

Inserting door window

– Fit door window -1- in window guide of door, inserting it diag‐
onally towards front of vehicle.
– Align window in window guides at front and rear and push
window downwards.
– Press window down into actuators.
– The actuators then engage in the window.
5.4 Removing and installing rear door win‐

dow
♦ Release tool - T40254-

Removing door window (standard glass)

– Remove window guide ⇒ page 181 .
– Remove inner window slot trim strip.
– Insert removal tool - T40231- on both sides of door window
and press downwards at mounting at window regulator -1-.
– This will bend open mounting at window regulator so that door
window with retaining pins can be lifted out.
– Pull door window -2- upwards out of mounting and lift out of
door.
Removing door window (insulating glass)

– Insert release tool - T40254- completely in direction of -dotted
arrow- in radius -arrow- of adapter.
– This will bend open mounting at window regulator so that door
window can be lifted out with retaining pins in adapter.
Installing door window
Note
When installing new standard-glass door windows, the retaining

pins must be pressed in first.
– Insert retaining pins -2- centrally in door window -1- and press
locking pin in until it is flush.
5. Door windows 317

– Fit door window -1- in window guide of door, inserting it diag‐

onally towards rear of vehicle.
– Align door window in window guides and slide window down‐
wards; make sure door window moves exactly into mounting
at front and rear.
– Press window down into mounting of window regulator.
– Retaining pins then engage audibly in mounting.

66 – Exterior equipment
1 Radiator grille/front trim panel
⇒ “1.1 Exploded view - radiator grille”, page 319
⇒ “1.2 Removing and installing radiator grille”, page 324
1.1 Exploded view - radiator grille

⇒ “1.1.1 Exploded view - radiator grille, Audi A6/S6 up to model
year 2014”, page 319
⇒ “1.1.2 Exploded view - radiator grille, Audi allroad”, page 320
⇒ “1.1.3 Exploded view - radiator grille, Audi A6 from model year
⇒ “1.1.4 Exploded view - radiator grille, Audi RS 6”, page 322
1.1.1 Exploded view - radiator grille, Audi A6/S6 up to model year 2014
1 - Audi rings
⇒ page 416
2 - quattro emblem
❑ Equipment version
⇒ page 418
3 - Retaining clip
❑ 2x
4 - Mounting (right-side)
❑ For parking aid sender
⇒ page 327
5 - Cover
❑ For Audi rings
logue
⇒ page 416
6 - Bolt
❑ 2x
❑ 1.5 Nm
7 - Mounting (left-side)
⇒ page 327
8 - Bolt
❑ 12x
❑ 1.5 Nm
9 - Radiator grille
1. Radiator grille/front trim panel 319

1.1.2 Exploded view - radiator grille, Audi allroad
1 - Radiator grille
⇒ page 324
2 - Bolt
❑ 2.5 Nm
3 - Closure plate (top)
– Unscrew bolts from clo‐
sure plate (top).
– If necessary, unclip
hose for headlight
washer system from clo‐
sure plate (top).
– Gradually release clips

and pull off closure plate
towards rear.
4 - Bumper cover
❑ Removed
5 - Clip
– Pull off clip -5- and pull
moulded foam insert out
from underneath clo‐
sure plate.
7 - Bolt
❑ 2 Nm
320 Rep. gr.66 - Exterior equipment

1.1.3 Exploded view - radiator grille, Audi A6 from model year 2015 onwards
1 - Cover
❑ For front camera
2 - Audi rings
⇒ page 416
3 - quattro emblem
❑ Equipment version
⇒ page 418
4 - Radiator grille
⇒ page 325
5 - Retaining strip
❑ For quattro emblem
6 - Cover
❑ For Audi rings
logue
⇒ page 416
7 - Bolt
❑ 1.5 Nm
8 - Mounting
❑ For front camera
⇒ Communication;
Rep. gr. 91 ; Overhead
view camera; Overview
of fitting locations - over‐
head view camera
9 - Bolt
❑ 6x
❑ 1.5 Nm

1.1.4 Exploded view - radiator grille, Audi RS 6
1 - Number plate holder

logue
⇒ page 326
2 - Bolt
❑ 2x
❑ 0.9 Nm
3 - Mounting
❑ For radiator grille (bot‐
tom)
4 - Audi rings
⇒ page 417
5 - Adapter
❑ For Audi rings
6 - RS 6 emblem
⇒ page 418
7 - Radiator grille
❑ Vehicles with front over‐
head view camera -
R243- : Opening must
be cut out before instal‐
ling component
⇒ page 322
⇒ page 325
8 - Retaining strip
9 - Radiator grille (bottom)
10 - Bolt
❑ 6x
❑ 1.5 Nm
11 - Cover
❑ For Audi rings
12 - Bolt
❑ 1.5 Nm
13 - Mounting
Cutting out opening for front overhead view camera - R243-

1 - Audi rings
⇒ page 417
2 - Adapter
❑ For Audi rings
3 - Radiator grille
– Mark dimensions for
RS 6 according to detail
view -B- ⇒ page 323 .
⇒ page 325
4 - Cover
❑ For Audi rings
logue
⇒ page 417
Opening for front overhead view camera - R243-

– Cut out opening with the following dimensions (as shown).
Dimension -b- is measured from centre of attachment points for
front overhead view camera - R243- .
♦ Dimension -a- = 50 mm ± 5 mm
♦ Dimension -b- = 20 mm ± 3 mm
♦ Dimension -c- = 6 mm ± 1 mm

1.2 Removing and installing radiator grille

⇒ “1.2.1 Removing and installing radiator grille - Audi A6/allroad/
S6 up to model year 2014”, page 324
⇒ “1.2.2 Removing and installing radiator grille - Audi A6 from
⇒ “1.2.3 Removing and installing radiator grille - Audi RS 6”, page
325
⇒ “1.2.4 Removing and installing radiator grille (bottom) - Audi
RS 6”, page 325
⇒ “1.2.5 Removing and installing number plate holder”,
page 326
⇒ “1.2.6 Removing and installing mounting bracket for front park‐
ing aid sender”, page 327
⇒ “1.2.7 Removing and installing mounting bracket for front park‐
ing aid sender - Audi RS 6”, page 327
1.2.1 Removing and installing radiator grille -

Audi A6/allroad/S6 up to model year
2014
Removing
– If installed, remove mounting for camera for night vision sys‐
tem ⇒ page 241 .
– If fitted, remove garage door operation control unit ⇒ Electrical
system; Rep. gr. 97 ; Control units; Removing and installing
garage door operation control unit .
– If installed, unplug electrical connectors -1 and 2- at front park‐
ing aid senders.
– Release retaining tabs -1- -arrow A- and push out radiator

grille towards front.
– Release lock carrier -2- at retaining catch -arrow B- and take
radiator grille out of bumper cover towards front.
Installing
Tightening torques
♦ ⇒ “1.1 Exploded view - radiator grille”, page 319


Audi A6 from model year 2015 onwards
Removing
– If fitted, pull washer fluid hose -4- for night vision system off
washer jet and move hose clear.
– Unplug electrical connector -1- for front parking aid sender and
move wiring harness clear.
– Release retaining tabs (top) -3- in two stages.
– Release retaining tabs -5- and take radiator grille -2- out of
bumper cover towards front.
Installing
Tightening torques
♦ ⇒ “1.1.3 Exploded view - radiator grille, Audi A6 from model

Audi RS 6
Removing
– Remove mounting bracket for front parking aid sender
⇒ page 327 .
– Release retaining tabs -1- -arrow- and take radiator grille -4-
out of bumper cover -3- towards front.
Installing
Tightening torques
♦ ⇒ “1.1.4 Exploded view - radiator grille, Audi RS 6”,
page 322
1.2.4 Removing and installing radiator grille

(bottom) - Audi RS 6
Removing
– Remove radiator grille ⇒ page 325 .

– Release retaining tabs -3, 4, 5- -arrows-.

– Detach radiator grille (bottom) -2- by pulling it inwards and at
the same time press off mounting -1- towards front.
– Remove radiator grille (bottom) and mounting.
Installing
Tightening torques
page 322
1.2.5 Removing and installing number plate

holder
Removing
– Detach number plate.
– Remove bolts -2- and -3-.
– Disengage number plate holder -1- upwards from honeycomb
grille -arrow-; this disengages retainers -4-.
– Detach number plate holder.
Installing
– The number plate holder must be inserted completely into the
honeycomb grille.
Tightening torques
page 322


bracket for front parking aid sender
Removing
– Release retaining hook -arrow- and press trim -2- for parking
aid sender towards front out of radiator grille -1-.
– If mounting bracket is to be renewed, remove front parking aid
sender ⇒ Electrical system; Rep. gr. 94 ; Parking aid; Re‐
moving and installing front parking aid senders .
Installing
– Press mounting bracket into radiator grille until it engages au‐
dibly.

bracket for front parking aid sender - Au‐
di RS 6
Removing
– Remove mounting for moulded foam insert ⇒ page 247 .
– If mounting bracket is to be renewed, remove parking aid
sender ⇒ Electrical system; Rep. gr. 94 ; Parking aid; Re‐
moving and installing front parking aid senders .
Installing
Tightening torques
page 322

2 Spoilers
⇒ “2.1 Exploded view - spoiler”, page 328
⇒ “2.2 Removing and installing spoiler”, page 330
2.1 Exploded view - spoiler

⇒ “2.1.1 Exploded view - spoiler for rear lid ”, page 328
⇒ “2.1.2 Exploded view - roof spoiler”, page 329
2.1.1 Exploded view - spoiler for rear lid
1 - Spoiler for rear lid

⇒ page 330
2 - Double-sided adhesive
tape
– Only pull protective film
off after positioning
spoiler on rear lid.
3 - Removal aid
– After positioning spoiler
exactly on rear lid, pull
protective film out be‐
tween rear lid and spoil‐
er using removal aid.
4 - Adhesive tape
– Mask area in front of and
behind spoiler with tape
to prevent damage
when removing spoiler.
5 - Orientation line
– For positioning spoiler
correctly in relation to
rear section of rear lid.

spoiler at sides and po‐
sition it on rear lid by
moving it towards rear
as far as (imaginary) ori‐
entation line.

2.1.2 Exploded view - roof spoiler
1 - Roof spoiler
⇒ page 331
2 - Clip
3 - Rear lid
4 - Nut
❑ 4 Nm
5 - Bolt
❑ 2.5 Nm
2. Spoilers 329
2.2 Removing and installing spoiler

⇒ “2.2.1 Removing and installing spoiler for rear lid”, page 330
⇒ “2.2.2 Removing and installing roof spoiler”, page 331
⇒ “2.2.3 Renewing seal for roof spoiler”, page 332
2.2.1 Removing and installing spoiler for rear

lid
Special tools and work‐
shop equipment re‐
quired
♦ Removal wedge -
3409-
♦ Hot air blower - V.A.G

1416-
♦ Cleaning solution - D
009 401 04-
Removing spoiler
– Mask rear lid with ad‐
hesive tape -4- in cut‐
ting area.
– Insert wire for remov‐
al kit - VAS 6452/2-
-2- on one side be‐
tween spoiler -1- and
rear lid.
– Pull ends of cutting
wire into two pull han‐
dles included with
cutting tool - V.A.G
1351- .

Cut through double-si‐

ded adhesive tape -3- on
spoiler (start at one side
and work across to other
side).
– Remove all residual
adhesive on rear lid
and spoiler before re-
installation.
– When installing,
move spoiler towards
rear as far as imagi‐
nary line
and position centrally
on rear lid.
Installing
Note
The rear lid and spoiler

must be at room temper‐
ature before they are in‐
stalled.
– Remove any residual

adhesive on rear lid
and spoiler, and
clean with cleaning
04- .
– Heat rear lid in bonding area with hot air blower - V.A.G 1416- .
– With the help of a second mechanic, move spoiler towards rear
as far as imaginary line -5- and position centrally on rear lid.
– Gradually pull out protective film between rear lid and spoiler
(working towards opposite side); at the same time, press on
spoiler.
– Press spoiler on firmly (starting at centre and working out‐
wards).
2.2.2 Removing and installing roof spoiler
2. Spoilers 331
1 - Roof spoiler
❑ Removing
Luggage compartment
trim panels; Overview of
fitting locations - lug‐
gage compartment trim
panels .
– Remove nuts -4- and

bolts -5-.

nector for brake light.
– Gradually unfasten clip
-2- from outside.
❑ Installing
– Install in reverse order
of removal; press clips
fully into rear lid from
outside.
2 - Clip
3 - Rear lid
4 - Nut
❑ 4 Nm
5 - Bolt
❑ 2.5 Nm
2.2.3 Renewing seal for roof spoiler

Removing
– Remove roof spoiler ⇒ page 331 .

– Detach seals -2- and -3- for roof spoiler.

Installing
– Remove any remaining adhesive.
– Bonding surfaces must be free from dust and grease.
– Clean bonding surface on spoiler with cleaning solution - D
009 401 04- .
– Apply plastic primer - D 366 PR1 A1- to bonding surface and
allow to flash off until cleaning solution has evaporated.
– Peel protective film off seals.
– Align seals centrally to roof spoiler and press on.
2. Spoilers 333
3 Strips / trim panels / extensions

⇒ “3.1 Exploded view - trim strip and covers”, page 334
⇒ “3.2 Exploded view - sill panel trim”, page 338
⇒ “3.3 Exploded view - side member trim”, page 339
⇒ “3.4 Exploded view - trim panel for B-pillar”, page 342
⇒ “3.5 Exploded view - trim panel for C-pillar”, page 344
⇒ “3.6 Exploded view - wheel arch covers”, page 345
⇒ “3.7 Exploded view - heat shield”, page 347
⇒ “3.8 Removing and installing trim strip”, page 349
⇒ “3.9 Removing and installing sill panel trim”, page 357
⇒ “3.10 Removing and installing cover”, page 358
⇒ “3.11 Removing and installing side member trim”, page 359
⇒ “3.13 Removing and installing trim panel for B-pillar on door”,
page 364
⇒ “3.14 Removing and installing trim panel for C-pillar on door”,
page 365
⇒ “3.15 Removing and installing wheel arch covers”, page 366
⇒ “3.16 Removing and installing heat shield for floor”, page 370
3.1 Exploded view - trim strip and covers

⇒ “3.1.1 Exploded view - trim strip and covers, Saloon”,
page 334
⇒ “3.1.2 Exploded view - trim strip and covers, Avant”,
page 336
⇒ “3.1.3 Exploded view - trim strip and covers, trim strip for doors
and side window”, page 337
3.1.1 Exploded view - trim strip and covers, Saloon

1 - Fastener
2 - Roof trim strip
⇒ page 349
3 - Fastener
❑ 11x
4 - Seal
❑ For trim strip for side
window
❑ Self-adhesive
5 - Trim strip for side window
⇒ page 350
6 - Clip
❑ 3x
7 - Pop rivet
❑ 3x
8 - Pop rivet
❑ 3x
9 - Clip
❑ 3x
3. Strips / trim panels / extensions 335

3.1.2 Exploded view - trim strip and covers, Avant
1 - Roof trim strip

⇒ page 349
2 - Clip
❑ 11x
3 - Side window
4 - Pop rivet
❑ 11x
5 - Clip
❑ 11x
❑ Removing and instal‐
ling: same procedures
as for Saloon
⇒ page 350

3.1.3 Exploded view - trim strip and covers, trim strip for doors and side window
1 - Trim strip for front door

⇒ page 352
2 - Trim strip for rear door (top)
⇒ page 353
3 - Trim strip for rear door
⇒ page 354
4 - Side window
❑ Part of side window;
cannot be renewed sep‐
arately if damaged
side window
⇒ page 310

3.2 Exploded view - sill panel trim
1 - Sill panel trim (front)

logue
⇒ page 357
2 - Sill panel trim (rear)
logue
⇒ page 357

3.3 Exploded view - side member trim

⇒ “3.3.1 Exploded view - side member trim”, page 339
⇒ “3.3.2 Exploded view - side member trim, allroad”, page 340
⇒ “3.3.3 Exploded view - side member trim and sill panel trim,
allroad”, page 341
3.3.1 Exploded view - side member trim
1 - Cover (front)
❑ For jacking point
❑ 7x
3 - Mounting (front)
❑ For quick-release fas‐
tener
❑ 3x
⇒ page 362
4 - Trim
❑ For side member trim
⇒ page 361
5 - Fastener
❑ 4x
6 - Bolt
❑ 8 Nm
7 - Bracket (front)
⇒ page 361
8 - Sill panel trim (front)
9 - Bracket (rear)
❑ 9x
⇒ page 362
10 - Sill panel trim (rear)
11 - Mounting (rear)
❑ For quick-release fastener
❑ 4x
13 - Side member trim
❑ e-tron: with trim strip; removing and installing ⇒ page 356
14 - Cover (rear)
❑ For jacking point

3.3.2 Exploded view - side member trim, allroad

❑ Removing
– Release rotary catches
by turning 90° and de‐
tach.
– Pull side member trim at

A-pillar (bottom) out of
retainer from side.
– Heat top of side member

trim at C-pillar with hot
air blower and carefully
detach double-sided ad‐
hesive tape.
– Gradually unclip and de‐

tach side member trim.
❑ Installing
– When installing, renew
abrasion guard and
double-sided adhesive
tape if necessary.

for double-sided adhe‐
sive tape with cleaning
04- .
– Position side member

trim at rear via centring
pin, and then press into
retainer at front.
– Press side member trim

gradually into side
member with clips -6-,
working from rear to
front.
– Press in rotary catches -8-.
– Firmly press onto bonding surface for double-sided adhesive tape again using roller - 3356- .
2 - Clip
– Inserted in side member
3 - Bracket
4 - Fitted bolt
❑ 8 Nm
5 - Nut
6 - Clip
– Clips damaged during removal must be renewed.
– Attach to side member trim as shown.

7 - Side member
8 - Rotary catch
– To remove, turn 90° and detach.
– Only press in when installing.
3.3.3 Exploded view - side member trim and sill panel trim, allroad
1 - Bolt
❑ 2.5 Nm
2 - Sill panel trim
Note
Sill panel trim is damaged irrepara‐

bly when removed; must be re‐
newed.
❑ Removing
– Unscrew bolts and heat
bonding surfaces on sill
panel trim with hot air
blower.
– Pull off sill panel trim.
– Completely remove any

remaining adhesive
from side member trim.
❑ Installing
– Clean bonding surfaces
D 009 401 04- .
– Peel protective film off

adhesive tape.
– Fit sill panel trim correct‐

ly into opening and
press on by hand.
– Firmly press sill panel

trim onto bonding surfa‐
ces again using roller -
3356- .
– Tighten bolts to specified torque.
3 - Grommet
4 - Adhesive strip (top)
– Supplied with sill panel trim
5 - Adhesive strip (bottom)

– Supplied with sill panel trim

3.4 Exploded view - trim panel for B-pillar

⇒ “3.4.1 Exploded view - window slot trim strip (front door), trim
panel for B-pillar”, page 342
⇒ “3.4.2 Exploded view - window slot trim strip (rear door), trim
3.4.1 Exploded view - window slot trim strip (front door), trim panel for B-pillar

❑ Exploded view
⇒ page 116
2 - Clip nut
⇒ page 364
4 - Bolt
❑ 2.5 Nm
5 - Clip nut
6 - Bolt
❑ 2.5 Nm
7 - Clip nut
8 - Bolt
❑ 2.5 Nm

3.4.2 Exploded view - window slot trim strip (rear door), trim panel for B-pillar
1 - Clip nut
2 - Bolt
❑ 2.5 Nm
3 - Clip nut
4 - Bolt
❑ 2.5 Nm
⇒ page 364
6 - Grommet
7 - Bolt
8 - Sealing piece
❑ For triangular C-pillar
trim
9 - Triangular C-pillar trim
❑ Exploded view
⇒ page 168

3.5 Exploded view - trim panel for C-pillar
1 - Clip nut
2 - Bolt
3 - Clip nut
4 - Bolt
6 - Grommet
7 - Bolt
❑ 2.5 Nm
8 - Sealing piece
❑ For triangular C-pillar
trim
9 - Triangular C-pillar trim
⇒ page 365
❑ Exploded view
⇒ page 168

3.6 Exploded view - wheel arch covers

⇒ “3.6.1 Exploded view - wheel arch covers (front)”, page 345
⇒ “3.6.2 Exploded view - wheel arch covers (rear)”, page 346
3.6.1 Exploded view - wheel arch covers (front)
1 - Wheel arch cover

⇒ page 366
2 - Wing panel
3 - Adhesive tape
4 - Centring pin

3.6.2 Exploded view - wheel arch covers (rear)
1 - Wheel arch cover for side

panel
⇒ page 367
2 - Trim for rear door
⇒ page 367
3 - Side panel
4 - Adhesive tape

3.7 Exploded view - heat shield

⇒ “3.7.1 Exploded view - heat shield (front)”, page 347
⇒ “3.7.2 Exploded view - heat shield (rear)”, page 348
3.7.1 Exploded view - heat shield (front)
1 - Nut
❑ 4x
❑ 2.1 Nm
2 - Heat shield (front)
❑ For tunnel (centre)
❑ For vehicles with TDI
engine
⇒ page 376
3 - Spring clip
❑ 3x
4 - Heat shield
❑ For longitudinal mem‐
ber
on vehicles with petrol
engine: left-side
⇒ page 371
on vehicles with TDI en‐
gine: left-side
⇒ page 373
5 - Retaining clip
6 - Nut
❑ 4x
❑ 2.1 Nm
7 - Heat shield
❑ For vehicles with petrol
engine
8 - Heat shield (left-side)
❑ For tunnel (top)
9 - Retaining clip
❑ Left side: 2x; right side: 3x
10 - Heat shield (right-side)
❑ For tunnel (top)
11 - Retaining clip
❑ 2x

12 - Heat shield
❑ For plenum chamber partition panel
❑ Audi RS 6 vehicles with additional cover for vacuum line
❑ Removing and installing on vehicles with petrol engine ⇒ page 374
❑ Removing and installing on vehicles with TDI engine ⇒ page 374
13 - Heat shield (rear)
❑ For vehicles with TDI engine
3.7.2 Exploded view - heat shield (rear)
1 - Nut
❑ 2x
❑ 2.1 Nm
2 - Heat shield
❑ For propshaft
⇒ page 377
3 - Bolt
❑ 8x
❑ 55 Nm
4 - Tunnel cross-piece
⇒ page 391
5 - Heat shield
❑ For tunnel (rear)
⇒ page 378
6 - Nut
❑ 4x
❑ 2.1 Nm
7 - Heat shield
❑ For rear silencer
⇒ page 380
8 - Washer
9 - Spring clip/nut
❑ Nut: 2.1 Nm
10 - Heat shield
❑ For exhaust system
(centre)
11 - Bolt
❑ Tightening torque ⇒ Fuel supply system; Rep. gr. 20 ; Fuel tank; Exploded view - fuel tank
12 - Bolt
❑ 20 Nm

❑ Vehicles with centre silencer: tightening torque ⇒ Rep. gr. 26 ; Exhaust pipes/silencers; Exploded view
- silencers .
3.8 Removing and installing trim strip

⇒ “3.8.1 Removing and installing roof trim strip”, page 349
⇒ “3.8.2 Removing and installing trim strip for side window”, page
350
⇒ “3.8.3 Removing and installing trim strip for front door - vehicles
⇒ “3.8.4 Removing and installing trim strip for rear door (top) -
vehicles from model year 2015 onwards”, page 353
⇒ “3.8.5 Removing and installing trim strip for rear door - vehicles
⇒ “3.8.6 Renewing rear lid trim strip”, page 355
⇒ “3.8.7 Removing and installing trim strip for side member trim -
e-tron”, page 356
3.8.1 Removing and installing roof trim strip

♦ Removal wedge - 3409-
Removing
Note
♦ Take care not to twist or bend roof trim strip.

♦ Mask area around roof trim strip at A-pillar with adhesive tape
to avoid damaging paintwork.
– Open front and rear doors.

– Starting at A-pillar, press roof trim strip -1- off retaining clips
-arrow- using removal wedge - 3409- .

– Pull roof trim strip -2- out of clips -1- in area of rear side win‐
dow.
– Have a second person hold the roof trim strip to avoid dam‐
aging the paintwork.
– Mask area around trim strip for side window -1- with adhesive
tape -3- as shown in illustration to avoid damaging paintwork.
– Pull roof trim strip -2- out of clip on side window -1- in direction
of -arrow-.
– Detach roof trim strip.
Installing
– Apply special lubricating paste - G 052 141 A2- into connecting

clip -5- and/or into guide -6-.
– Fit roof trim strip -1- in trim strip -7- for side window.
• Clip -5- must be inserted correctly in guide -6-.
• Roof trim strip must make flush contact with trim strip for side
window.
– Align the two centring pins -2- of roof trim strip with holes -3-
in roof of vehicle.
– Press roof trim strip into clips in area of side window and onto
retaining clips -4- so they engage audibly.

side window

♦ Wedges - T10383-
Removing
Note
Take care not to twist or bend trim strip for side window.
– Remove roof trim strip ⇒ page 349 .

– Mask area around trim strip for side window -2- with adhesive
tape -1- as shown in illustration to avoid damaging paintwork.
– Press trim strip for side window off clips using wedge -
T10383/1- .
– Detach trim strip for side window.
Installing
– Coat rubber strips and trim strip of side window with tyre as‐
sembly paste.
Caution
Risk of damage to rubber strip.

♦ If the rubber strip is not behind the trim strip, the rubber
strip will be damaged when it is guided out subsequently.
♦ The rubber strip must be renewed if it is damaged (Re‐
newing side window ⇒ page 310 ).

– Position trim strip -1- for side window at C-pillar on corner

-arrow- of rubber strip on body, as shown in illustration.
• Rubber strip -2- must be above trim strip.
• Clips -4- must be parallel to trim strip for side window.
– Press trim strip for side window onto clips so they engage au‐
dibly.
• Rubber strip must be above trim strip for side window.
• In bend of trim strip for side window, carefully fit rubber strip
-3- above trim strip using wedge -T10383/1- .

front door - vehicles from model year
2015 onwards
♦ Removal wedge - T40233-
Removing
– Starting at bottom, lever trim strip -1- out of window guide -2-
-arrow- using removal wedge - T40233- , as shown in illustra‐
tion.
– Carefully lever trim strip out of window guide along entire
length and detach.
Installing

– Align trim strip -1- on door flange at B-pillar, insert into guide
slot -3- for window guide -2- from below and press on along
entire length.

rear door (top) - vehicles from model
year 2015 onwards
Removing
– Remove trim strip for rear door ⇒ page 354 .

– Starting at bottom, lever trim strip -1- out of window guide -2-
tion.
length; while doing so, pull spring clip -4- out of guide slot for
window guide -3-.
– Remove trim strip.
Installing
– Insert spring clip -4- into guide slot -5-.

– Insert trim strip -1- into guide slot -3- for window guide -2- from
below and press on along entire length.

rear door - vehicles from model year
2015 onwards

Removing
– Starting at top, lever trim strip -1- out of window guide -2-
tion.
length and detach.
Installing
– Align trim strip -1- on trim strip (top), insert into spring clip -2-
and guide slot -4- for window guide -3- from below and press
on along entire length.
3.8.6 Renewing rear lid trim strip


♦ Roller - 3356-

– Heat bonding surface from inside of rear lid with a hot air blow‐
er - V.A.G 1416- and pull it off gradually.
Remove any remaining adhesive from rear lid.
– Clean bonding surfaces on body with cleaning solution - D 009
401 04- .
– To install, align centrally with exact contour of rear lid.

– Remove protective film from between rear lid and trim strip by
pulling it out gradually using removal aids and press trim strip
on firmly by hand.
– After installing, press on trim strip again with roller - 3356- .

side member trim - e-tron
Removing
– Remove side member trim ⇒ page 359 .
– Release fasteners -arrows- and detach trim strip (rear) -1-
from side member trim -2-.

– Release fasteners -arrows- and detach trim strip (front) -2-

from side member trim -1-.
Installing
3.9 Removing and installing sill panel trim


Removing
Vehicles with light conductors for ambient lighting:
– Remove sill panel trim (front) ⇒ General body repairs, interior;
Rep. gr. 70 ; Passenger compartment trim panels; Removing
and installing sill panel trim .
– Pull inner door seal off body flange only at bottom in area of
sill panel trim ⇒ page 100 .

– Unplug electrical connector.

– Carefully heat sill panel trim -1- with hot air blower - V.A.G
1416- .
– Use removal wedge - 3409- to carefully prise sill panel trim off
side member -2- -arrow-.
Installing
– Clean bonding surface on body with cleaning solution - D 009
401 04- .
– Peel protective film off adhesive strip -3-.

– Fit sill panel trim -2- on side member -1-, making sure that
locating lugs are pressed into mountings -arrows-.
– Press sill panel trim onto side member over entire length.
• Leave vehicle standing at room temperature for at least 2
hours.
3.10 Removing and installing cover

Cover for wheel housing liner - e-tron


Removing
– Carefully heat cover -3- for wheel housing liner with hot air
blower - V.A.G 1416- .
– Detach cover -3- from wing -2-.
Installing
– Check grommets -1- for damage.

401 04- .
– Peel protective films off adhesive strips -1, 2, 3-.
– Position cover -4- on wing and press locating elements into
grommets.
– Press cover on over entire length of wing.
• Leave vehicle standing at room temperature for at least 2
hours.
3.11 Removing and installing side member

trim
⇒ “3.11.1 Removing and installing side member trim”, page 359
⇒ “3.11.2 Removing and installing trim for side member trim”,
page 361
⇒ “3.11.3 Removing and installing bracket (front) for side member
trim”, page 361
⇒ “3.11.4 Removing and installing bracket (rear) for side member
trim”, page 362
⇒ “3.11.5 Removing and installing mountings (front and rear) for
quick-release fasteners”, page 362
3.11.1 Removing and installing side member

trim


Removing
– Unfasten underbody cover (rear) in area of side member trim
⇒ page 387 .
– Unfasten underbody cover (centre) in area of side member
trim ⇒ page 386 .
– Carefully heat side member trim -1- with hot air blower - V.A.G
1416- in area of C-pillar -2-.
– Use removal wedge - 3409- to carefully prise off side member
trim -arrow A-.
– Release quick-release fastener -3-.
– Lift side member trim at bottom slightly and pull outwards
-arrow B-.

– Pull side member trim -1- first off retainer at front -arrow A- and
then off retainers at rear -2- -arrow B-.
– Detach side member trim and set it down on a soft surface.
Installing
– Remove bracket (rear) for side member trim and position on
side member trim ⇒ page 362 .
401 04- .
– Peel protective film off adhesive strip -2-.

– Position side member trim -1- on C-pillar and on vehicle body
and press it on until brackets (rear) and clips engage audibly.
3.11.2 Removing and installing trim for side

member trim
Removing
– Detach front section of side member trim ⇒ page 359 .
– Release fasteners -arrows-.
– Detach trim -2- from side member trim -1-.
Installing
3.11.3 Removing and installing bracket (front)

for side member trim
Removing

– Remove bolt -arrow-.

– Detach bracket (front) -1- for side member trim.
Installing
Tightening torques
♦ ⇒ “3.3 Exploded view - side member trim”, page 339
3.11.4 Removing and installing bracket (rear)

for side member trim
Removing
– Use small screwdriver -2- to release retaining tabs -arrows-
and at the same time swivel bracket (rear) -1- outwards.
– Detach bracket (rear) for side member trim.
Installing

– Fit bracket (rear) -1- in recess on side member trim -2-.
3.11.5 Removing and installing mountings

(front and rear) for quick-release fasten‐
ers
Removing

– Release retaining tabs -arrows- using a small screwdriver.

– Detach mounting -1- downwards.
Installing
– Press on mounting for quick-release fastener until it engages
audibly.
3.12 Removing and installing water deflector strip
1 - Pop rivet
❑ 5x
❑ Start from top when riv‐
eting guide rail.
2 - Guide rail
❑ To remove, drill out rivet
heads -4- and knock out
rivets.
3 - Water deflector strip
❑ Press all the way into
guide rail starting at top
and working down.
❑ Ensure flush fit at tran‐
sition to A-pillar.

3.13 Removing and installing trim panel for B-

pillar on door
⇒ “3.13.1 Removing and installing trim panel for B-pillar on front
door”, page 364
⇒ “3.13.2 Removing and installing trim panel for B-pillar on rear
door”, page 364
3.13.1 Removing and installing trim panel for B-

pillar on front door
Removing
frame trim .
– Pull window guide -1- out of guide (rear).
– Remove bolts -arrows A-.
– Slide trim panel for B-pillar -item 6- downwards -arrow B-; lug
-5- at top will be disengaged from window seal -4- and lug
-2- will be disengaged from body cut-out -3-.
– Press trim panel for B-pillar towards outside until surrounding
section of trim panel for B-pillar is disengaged.
– Pull trim panel for B-pillar upwards out of door opening.
Installing
Tightening torques
♦ ⇒ “3.4.1 Exploded view - window slot trim strip (front door), trim
3.13.2 Removing and installing trim panel for B-

pillar on rear door
Removing
frame trim .

– Pull window guide -6- out of guide (front) in area of bolts.

– Remove bolts -arrows A-.
– Slide trim panel for B-pillar -item 1- downwards -arrow B-; lug
-2- at top will be disengaged from window seal -3- and lug
– Press trim panel for B-pillar towards outside until surrounding
section of trim panel for B-pillar is disengaged.
– Pull trim panel for B-pillar upwards out of door opening.
Installing
Tightening torques
♦ ⇒ “3.4.2 Exploded view - window slot trim strip (rear door), trim
3.14 Removing and installing trim panel for

C-pillar on door
Removing
frame trim .
– Prise out grommet -1-.
– Slide triangular C-pillar trim -item 1- downwards -arrow-; lug

-2- will be disengaged from window seal -3- and retaining pin
– Pull triangular C-pillar trim upwards out of door opening.
Installing
Tightening torques
♦ ⇒ “3.4.2 Exploded view - window slot trim strip (rear door), trim

3.15 Removing and installing wheel arch cov‐

ers
⇒ “3.15.1 Renewing wheel arch cover for wing”, page 366
⇒ “3.15.2 Renewing wheel arch cover for side panel and rear
door”, page 367
3.15.1 Renewing wheel arch cover for wing

♦ Roller - 3356-
♦ Template - T40038 /8-
Note
♦ Panels that have been bonded on are damaged irreparably

when removed and cannot be re-installed (i.e. they must be
renewed).
♦ Remove any remaining adhesive from the body.
♦ Clean bonding surfaces on body with cleaning solution - D 009
401 04- .
♦ Before bonding, heat bonding surfaces and panels to approx.
40° C.
♦ When fitting panels, make sure that the position of the panel
is matched exactly to the contour of the body (it is not possible
to adjust the position after the panel makes contact).
♦ After installing, press on covers again with roller - 3356- .

1 - Wheel arch cover

❑ Removing:
– Heat bonding surface
with hot air blower and
pull cover off in stages.
– Completely remove any

residual adhesive from
side panel.
❑ Installing:
– Kink side sections of
protective film (removal
aids) so they can be
gripped easily when
cover makes contact
with wing.
– To install, apply from

rear to front, matching to
exact contour of body
via centring pin.
– Remove protective film

from between side pan‐
el and cover by pulling it
out via removal aids and
gradually press cover
on firmly using roller -
3356- .
2 - Wing
3 - Adhesive tape
❑ Before installing, kink
side sections of protec‐
tive film (removal aids)
90° so they can be
reached when wheel
arch cover makes con‐
tact with wing.
4 - Centring pin
3.15.2 Renewing wheel arch cover for side

panel and rear door
♦ Roller - 3356-

♦ Template - T40038 /8-
Note
♦ Panels that have been bonded on are damaged irreparably

when removed; they must therefore be renewed.
♦ Remove any remaining adhesive from the body.
♦ Clean bonding surfaces on body with cleaning solution - D 009
401 04- .
♦ Before bonding, heat bonding surfaces and panels to approx.
40° C.
♦ When fitting panels, make sure that the position of the panel
is matched exactly to the contour of the body (it is not possible
to adjust the position after the panel makes contact).
♦ After installing, press on covers again with roller - 3356- .

1 - Wheel arch cover for side

panel
❑ Removing:
– Heat bonding surface
with hot air blower and
pull cover off in stages.
❑ Installing:
– Kink side sections of
protective film (removal
aids) so they can be
reached when cover
makes contact with side
panel.
– To install, match to ex‐
act contour of side
member trim and door
trim.
– Remove protective film

from between side pan‐
el and cover by pulling it
out via removal aids and
gradually press trim on
firmly by hand.
2 - Trim for rear door

❑ Removal and installa‐
tion as described for
wheel arch cover
3 - Side panel
4 - Adhesive tape
❑ Before installing, kink
side sections of protec‐
tive film (removal aids)
90° so they can be
reached when wheel
arch cover makes contact with wing.

3.16 Removing and installing heat shield for

floor
⇒ “3.16.1 Removing and installing heat shield for longitudinal
member (left-side) - vehicles with petrol engine”, page 370
member (right-side) - vehicles with petrol engine”, page 371
member (left-side) - vehicles with TDI engine”, page 372
member (right-side) - vehicles with TDI engine”, page 373
⇒ “3.16.5 Removing and installing heat shield for plenum cham‐
ber partition panel - vehicles with petrol engine”, page 374
⇒ “3.16.6 Removing and installing heat shield for plenum cham‐
ber partition panel - vehicles with TDI engine”, page 374
⇒ “3.16.7 Removing and installing heat shield for tunnel (top left)”,
page 375
⇒ “3.16.8 Removing and installing heat shield for tunnel (top
right)”, page 375
⇒ “3.16.9 Removing and installing heat shield for tunnel (centre)
- vehicles with petrol engine”, page 375
⇒ “3.16.10 Removing and installing heat shield for tunnel (front
centre) - vehicles with TDI engine”, page 376
⇒ “3.16.11 Removing and installing heat shield for tunnel (rear
centre) - vehicles with TDI engine”, page 377
⇒ “3.16.12 Removing and installing heat shield for propshaft”,
page 377
⇒ “3.16.13 Removing and installing heat shield for tunnel (rear)”,
page 378
⇒ “3.16.14 Removing and installing heat shield for exhaust sys‐
tem (centre)”, page 379
⇒ “3.16.15 Removing and installing heat shield for rear silencer”,
page 380
3.16.1 Removing and installing heat shield for

longitudinal member (left-side) - vehi‐
cles with petrol engine
Removing
– Remove noise insulation: front ⇒ page 382 , rear
⇒ page 382 .
– Prise out spring clips -1 and 2- from gearbox side and spring
clip -5- from engine mounting side.

– Drain coolant ⇒ Rep. gr. 19 ; Cooling system/coolant; Drain‐

ing and filling cooling system .
– Disconnect coolant line (lift retaining clip -2- and swivel to one
side).
– Lift retaining clip -arrow-, disconnect coolant hose (left-side)

from coolant pipe (front) and move coolant hose clear.
– Remove securing clip -3-.

– Swivel heat shield -4- for longitudinal member (front) upwards
and remove.
Installing
– Install coolant hose and coolant line ⇒ Rep. gr. 19 ; Cooling
system/coolant; Draining and filling cooling system .
Tightening torques
♦ ⇒ “3.7 Exploded view - heat shield”, page 347

longitudinal member (right-side) - vehi‐
Removing
⇒ page 382 .

– Remove air pipe for air cleaner housing ⇒ Rep. gr. 24 ; Air
cleaner; Exploded view - air cleaner housing .
and remove.
Installing
Tightening torques

longitudinal member (left-side) - vehi‐
cles with TDI engine
Removing
• Engine cold
⇒ page 382 .
– Remove lock carrier brace (left-side) ⇒ page 10 .
– Release hose clip -3- and detach air hose.

– Unscrew nuts -arrows- and move coolant pipe clear at longi‐

tudinal member.

– Disconnect coolant line (lift retaining clip -arrow-) and swivel
to one side.
– Move coolant expansion tank -1- as far as possible to the side.

and remove.
Installing
– Install coolant expansion tank and coolant line ⇒ Rep. gr. 19 ;
Coolant pipes; Exploded view - coolant pipes .
– Install air hose ⇒ Rep. gr. 21 ; Charge air system; Exploded
view - hose connections for charge air system .
Tightening torques

longitudinal member (right-side) - vehi‐
Removing
⇒ page 382 .

– Remove air pipe for air cleaner housing ⇒ Rep. gr. 23 ; Air
cleaner; Exploded view - air cleaner housing .
– Remove bolt -3- and securing clip -4-.
and remove.
Installing
– Install coolant line ⇒ Rep. gr. 19 ; Coolant pipes; Exploded
view - coolant pipes .
Tightening torques

plenum chamber partition panel - vehi‐
Removing
– Remove plenum chamber partition panel ⇒ page 18 .
– Remove securing clips -arrows-.
– Detach heat shield -1- from plenum chamber partition panel.
Installing
Tightening torques

plenum chamber partition panel - vehi‐
Removing
– Detach heat shield -1- from plenum chamber partition panel.
Installing
Tightening torques


tunnel (top left)
Removing
– Vehicles with petrol engine: Unfasten catalytic converter (left-
side) ⇒ Rep. gr. 26 ; Emission control system; Removing and
installing catalytic converter .
– Vehicles with TDI engine: Remove particulate filter ⇒ Rep. gr.
26 ; Emission control system; Removing and installing partic‐
ulate filter .
– Lift out heat shield -2-.
Installing
– Make sure that heat shield is inserted behind heat shield -1-
on right side and behind heat shield -3- for tunnel (centre).
Tightening torques

tunnel (top right)
Removing
– Vehicles with petrol engine: Unfasten catalytic converter
(right-side) ⇒ Rep. gr. 26 ; Emission control system; Remov‐
ing and installing catalytic converter .
– Vehicles with TDI engine: Remove particulate filter ⇒ Rep. gr.
26 ; Emission control system; Removing and installing partic‐
ulate filter .
– Lift out heat shield -1-.
Installing
– Make sure that heat shield is inserted behind heat shield for
tunnel (centre).
Tightening torques

tunnel (centre) - vehicles with petrol en‐
gine
Removing
– Remove shift unit ⇒ Rep. gr. 34 ; Selector mechanism; Re‐
moving and installing selector mechanism / ⇒ Rep. gr. 37 ;

Selector mechanism; Removing and installing selector mech‐

anism .
– Remove heat shield for tunnel (rear) ⇒ page 378 .
– Prise out spring clips -arrows-.
– Detach heat shield -3- towards rear.
Installing
Tightening torques

tunnel (front centre) - vehicles with TDI
engine
Removing
– Remove heat shield for tunnel (centre) ⇒ page 377 .
– Remove shift unit ⇒ Rep. gr. 34 ; Selector mechanism; Re‐
moving and installing selector mechanism / ⇒ Rep. gr. 37 ;
Selector mechanism; Removing and installing selector mech‐
anism .
– Prise out spring clips -arrows-.
– Detach heat shield -3- towards rear.
Installing
Tightening torques


tunnel (rear centre) - vehicles with TDI
engine
Removing
– Remove fastener -9- from cover (front left) -3-.
– If fitted, remove spreader rivet -8-.
– Turn heat shield -1- downwards and detach.

Installing
– Install underbody cover (centre) ⇒ page 386 .
Tightening torques

propshaft
♦ Retainer - VW 785/1 B-

Removing
Vehicles with petrol engine:
Caution
Risk of damage to flexible joint in front silencer.

♦ Do not kink flexible joint in front silencer more than 10°.
– Loosen clamps -1 and 2-, slide them to rear and place front
silencer on retainer - VW 785/1 B- .

– Remove nuts -arrows-.
– Slide heat shield -1- towards front (as seen in direction of trav‐
el) and take it out.
– Vehicles with petrol engine: Take out heat shield towards rear
with exhaust pipes hanging down slightly.
Installing
– Install exhaust system ⇒ Rep. gr. 26 ; Exhaust pipes/silenc‐
ers; Exploded view - silencers .
Tightening torques

tunnel (rear)
Removing
– Remove rear section of exhaust system ⇒ Rep. gr. 26 ; Ex‐
haust pipes/silencers; Exploded view - silencers .
– Remove heat shield for propshaft ⇒ page 377 .

– Detach propshaft from rear final drive and tie up ⇒ Rear final
drive; Rep. gr. 39 ; Propshaft; Removing and installing prop‐
shaft .
– Remove bolts -arrows- for propshaft centre bearing.
– Carefully lower propshaft.
– Remove cross piece ⇒ page 391 .

– Take out heat shield -1- towards rear.
Installing
Tightening torques

exhaust system (centre)
Removing
– Remove underbody cover (rear left) ⇒ page 387 .
– Detach spring clip/unscrew nut -3- and remove bolts
-1 and 4-.
– Vehicles with petrol engine: Turn mounting -2- for centre si‐
lencer in direction of -arrow-.
– Take out heat shield -1-, guiding it out past exhaust system
-2- towards left side.
Installing

– When inserting bolt -3-, washer -2- must be located on heat

shield -1-.
– Install underbody cover (rear left) ⇒ page 387 .
Tightening torques
♦ ⇒ Fuel supply system; Rep. gr. 20 ; Fuel tank; Exploded view
- fuel tank
♦ ⇒ Rep. gr. 26 ; Exhaust pipes/silencers; Exploded view - si‐
lencers

rear silencer
Removing
– Unscrew nut -2- and turn mounting -1- for rear silencer -3- to‐
wards rear.
– Turn heat shield -5- towards spare wheel well -4- and detach
downwards.
Installing
– Install rear silencer ⇒ Rep. gr. 26 ; Exhaust pipes/silencers;
Exploded view - silencers .
Tightening torques

4 Noise insulation
⇒ “4.1 Exploded view - noise insulation”, page 381
⇒ “4.2 Removing and installing noise insulation”, page 382
⇒ “5.4 Removing and installing tunnel cross-piece”, page 391
4.1 Exploded view - noise insulation
1 - Bolt - M8
❑ 4x
❑ 20 Nm
❑ 3x
3 - Noise insulation (front)
❑ For engine
logue
⇒ page 382
4 - Noise insulation (rear)
❑ For gearbox
logue
⇒ page 382
5 - Cowl
6 - Rubber washer
❑ 7x
❑ 7x
8 - Bolt - M6
❑ 3x
❑ 3.5 Nm
4. Noise insulation 381

4.2 Removing and installing noise insulation

⇒ “4.2.1 Removing and installing noise insulation (front)”,
page 382
⇒ “4.2.2 Removing and installing noise insulation (rear)”,
page 382
4.2.1 Removing and installing noise insulation

(front)
Removing
– Unscrew bolts -1 and 2- and release quick-release fasteners
-3 and 4-.
– Pull noise insulation (front) -5- off to the rear.
• This disengages guide tabs on noise insulation (front).
– Detach noise insulation (front).
Installing
Tightening torques
♦ ⇒ “4.1 Exploded view - noise insulation”, page 381
4.2.2 Removing and installing noise insulation

(rear)
Removing
– Release quick-release fasteners -2 and 4-.
– Detach noise insulation (rear) -3-.
Installing

5 Underbody trim
⇒ “5.1 Exploded view - underbody trim”, page 383
⇒ “5.2 Exploded view - underbody struts”, page 385
⇒ “5.3 Removing and installing underbody trim”, page 386
⇒ “5.4 Removing and installing tunnel cross-piece”, page 391
⇒ “5.5 Removing and installing diagonal struts”, page 391
5.1 Exploded view - underbody trim

⇒ “5.1.1 Exploded view - underbody trim (front)”, page 383
⇒ “5.1.2 Exploded view - underbody trim (rear)”, page 384
5.1.1 Exploded view - underbody trim (front)
1 - Nut
❑ With retaining element
❑ 2.1 Nm
2 - Fastener
3 - Underbody cover (front)
⇒ page 386
4 - Nut
❑ With retaining element
❑ 10x
❑ 2.1 Nm
5 - Underbody cover (centre)
⇒ page 386
6 - Nut
❑ 4x
❑ 2.1 Nm
7 - Rear cover (left-side)
⇒ page 388
8 - Stone deflector strip
⇒ page 389
9 - Bolt
❑ 2.1 Nm
10 - Retaining clip
11 - Underbody cover (rear)
⇒ page 387
12 - Bolt
❑ 3.5 Nm
13 - Bolt
❑ 4x
❑ 2.1 Nm
5. Underbody trim 383

14 - Fastener
5.1.2 Exploded view - underbody trim (rear)
1 - Nut
❑ 2x
❑ 2.1 Nm
2 - Fastener
3 - Bolt
❑ 2.1 Nm
4 - Nut
❑ 2.1 Nm
5 - Cover (rear) for underbody
(right-side)
6 - Centre cover (rear)
⇒ page 390
7 - Cover (front) for spare
wheel well
⇒ page 389
8 - Nut
❑ 5x
❑ 2.1 Nm
9 - Washer
❑ 2x
10 - Bolt
❑ 2x
❑ 15 Nm
11 - Rear cover (right-side)
⇒ page 390
12 - Nut
❑ 2.1 Nm
13 - Fastener
14 - Nut
❑ 20 Nm

5.2 Exploded view - underbody struts
1 - Bolt
❑ 50 Nm +90°
2 - Diagonal strut (left-side)
⇒ page 391
3 - Bolt
❑ 50 Nm +90°
4 - Diagonal strut (top)
❑ e-tron only
⇒ page 392
5 - Bolt
❑ 2x
❑ 18 Nm
6 - Diagonal strut (bottom)
❑ e-tron only
⇒ page 392
7 - Bolt
❑ 50 Nm +90°
8 - Bolt
❑ 50 Nm +90°
9 - Diagonal strut (right-side)
⇒ page 391

5.3 Removing and installing underbody trim

⇒ “5.3.1 Removing and installing underbody cover (front)”,
page 386
⇒ “5.3.2 Removing and installing underbody cover (centre)”, page
386
⇒ “5.3.3 Removing and installing underbody cover (rear)”,
page 387
⇒ “5.3.4 Removing and installing underbody cover (rear left)”,
page 388
⇒ “5.3.5 Removing and installing stone deflector strip”,
page 389
⇒ “5.3.6 Removing and installing cover (front) for spare wheel
well”, page 389
⇒ “5.3.7 Removing and installing cover (centre)”, page 390
⇒ “5.3.8 Removing and installing cover (rear right)”, page 390
5.3.1 Removing and installing underbody cov‐

er (front)
Removing
– Remove nut -3- and fastener -1-.
– Pull cover (front) -2- out of fastener towards front.
– Detach cover (front).
Installing
Tightening torques
♦ ⇒ “5.1 Exploded view - underbody trim”, page 383

er (centre)
Removing
– Remove underbody cover (front) ⇒ page 386 .

– Remove fasteners -4 and 9- and nuts -1, 2, 5, 6 and 7-.

– Pull cover (centre) -3- out of fastener towards front.
– Detach cover (centre).
Installing
Tightening torques

er (rear)
Removing
Left side of vehicle:
– Unscrew nut -5- at cover (centre) -4-.
– Pull cover (rear) -2- out of fastener towards rear.
– Detach cover (rear).

Right side of vehicle:

– Unscrew nut -5- and bolts -1 and 6-.
– Unscrew nut -3- at cover (centre) -4-.
– Pull cover (rear) -2- out of fastener towards rear.
– Detach cover (rear).
Installing
Tightening torques

er (rear left)
Removing
– Remove bolts -1, 2- and nuts -arrows-.
– Detach cover (rear) -3-.
Installing
Tightening torques

5.3.5 Removing and installing stone deflector

strip
Removing
– Remove bolts -2 and 3- and detach retaining clip -4-.
– Detach stone deflector strip -1-.
– To detach retaining clip -3-, use narrow long-nose pliers to

disengage release lever -2- in direction of -arrow A- and press
it off retaining pin -1- in direction of -arrow B-.
Installing
Tightening torques
5.3.6 Removing and installing cover (front) for

spare wheel well
Removing
– Detach cover (front) -1- for spare wheel well.
Installing
Tightening torques

5.3.7 Removing and installing cover (centre)

Removing
– Release fastener -1-.
– Unscrew nuts -5, 7, 8- and bolts -6-.
– Unscrew bolts -3- (pay attention to washers -4-).
– Detach cover (centre) -2-.
Installing
Tightening torques
5.3.8 Removing and installing cover (rear

right)
Removing
– Release fastener -6-.
– Unscrew nuts -3, 4, 7- and bolt -2-.
– Press down cover (centre) -1- slightly and detach cover (rear
right) -5-.
Installing
Tightening torques

5.4 Removing and installing tunnel cross-

piece
Removing
– Remove bolts -1, 3, 4, 5-.

– Detach cross piece -2-.
Installing
Tightening torques
5.5 Removing and installing diagonal struts

⇒ “5.5.1 Removing and installing diagonal struts - Avant”,
page 391
⇒ “5.5.2 Removing and installing diagonal struts - e-tron”,
page 392
5.5.1 Removing and installing diagonal struts

- Avant
⇒ page 385 .
Removing
– Remove underbody covers (rear) ⇒ page 387 .

– Remove bolts -1 … 4- and detach diagonal struts.

Installing
• Vehicle must be standing on its wheels when tightening bolts.
Tightening torques
♦ ⇒ “5.2 Exploded view - underbody struts”, page 385
5.5.2 Removing and installing diagonal struts

- e-tron
⇒ page 385 .
Removing
– Remove exhaust system (rear) ⇒ Rep. gr. 26 ; Exhaust pipes/
silencers; Exploded view - silencers .
– Remove underbody covers (rear) ⇒ page 387 .
– Remove bolts -arrows- and detach diagonal struts -1-.
Installing
• Vehicle must be standing on its wheels when tightening bolts.
Tightening torques
♦ ⇒ “5.2 Exploded view - underbody struts”, page 385

6 Decorative film / protective film

⇒ “6.1 Exploded view - protective film”, page 393
⇒ “6.2 Renewing protective film”, page 394
6.1 Exploded view - protective film
1 - Protective film for wing

2 - Protective film for door
3 - Protective film for side
member trim (front)
member trim (rear)
frame
6. Decorative film / protective film 393

6.2 Renewing protective film
Note
♦ Fit protective film as follows.

e.g. cleaning solution - D 009 401 04- ).
♦ Fully moisten the bonding surfaces (on body side) with a wa‐
ter-isopropanol mix (e.g. cleaning solution - D 009 401 04- )
or drinking water with 2-3 drops of washing-up liquid added.
♦ Detach backing from protective film and also moisten its bond‐
ing surface.
♦ Align film evenly according to body contours.
♦ Press on film from the middle outwards so that any water under
the film can be pressed out.
♦ When doing so, ensure that no air bubbles remain trapped.
♦ Pierce air bubbles with a small needle if necessary and press
out the air.

7 Roof strips / roof rails

⇒ “7.1 Exploded view - roof rail”, page 395
⇒ “7.2 Removing and installing roof rail”, page 395
7.1 Exploded view - roof rail
1 - Roof rail
⇒ page 395
2 - Nut
❑ 10 Nm
4 - Roof
7.2 Removing and installing roof rail
Caution
If re-installing nuts, it is important to use locking fluid when

screwing in.
7. Roof strips / roof rails 395

1 - Roof rail
❑ Removing
headliner .
– Unfasten curtain airbag

and lift to side.
– Remove nuts and lift

roof rail off roof.
❑ Installing
– Adjuster elements must
be inserted in roof and
be pre-tensioned slight‐
ly in correct installation
position.
– Position roof rail on roof

so that studs are inser‐
ted in adjuster ele‐
ments.
❑ Observe tightening se‐
quence:
– First tighten the two in‐
ner nuts, and then tight‐
en outer nuts to speci‐
fied torque.
2 - Nut
⇒ page 395
❑ Insert front adjuster element in hole provided and push it to rear into its installation position.
❑ Insert remaining adjuster elements into holes provided and push them forwards into installation position.
❑ Move adjuster elements into contact with outer panel so that they are pre-tensioned slightly (0.4 Nm).
4 - Roof

8 Exterior mirror
⇒ “8.1 Exploded view - exterior mirror”, page 397
⇒ “8.2 Removing and installing exterior mirror”, page 398
⇒ “8.3 Removing and installing mirror glass”, page 399
⇒ “8.4 Removing and installing mirror adjustment unit”,
page 400
⇒ “8.5 Removing and installing cover for mirror”, page 400
8.1 Exploded view - exterior mirror
1 - Mirror glass
⇒ page 399
2 - Housing for exterior mirror
⇒ page 400
3 - Cover for mirror
❑ For mounting for mirror
adjustment unit
⇒ page 398
4 - Mirror adjustment unit
⇒ page 400
5 - Bolt
❑ 2x
Electrical system; Rep.
gr. 94 ; Lights in exterior
mirror; Exploded view -
lights in exterior mirror
6 - Turn signal repeater bulb in
exterior mirror
Rep. gr. 94 ; Lights in
exterior mirror; Remov‐
ing and installing turn
signal repeater bulb -
L131- / -L132-
7 - Lane change assist warning
lamp in exterior mirror
⇒ Electrical system; Rep. gr. 96 ; Lane change assist; Removing and installing lane change assist
warning lamp in exterior mirror -K233- / -K234-
8 - Mounting for mirror adjustment unit
❑ Combined in one component with cover
9 - Gasket
❑ For mirror base
10 - Bolt
❑ 3x
8. Exterior mirror 397

❑ 6 Nm
11 - Bolt
❑ 1 Nm
8.2 Removing and installing exterior mirror

⇒ “8.2.1 Removing and installing exterior mirror”, page 398
⇒ “8.2.2 Removing and installing cover for exterior mirror”,
page 398
8.2.1 Removing and installing exterior mirror

Removing
frame trim .
– Pull catch -1-, press release mechanism and unplug electrical
connector -2-.
– Take out sealing plugs -4 and 5-.
– Detach mounting for mirror adjustment unit and at the same
time guide sealing grommet -3- with wiring harness -2- out
through opening in body.
Installing
– On vehicles with overhead view camera, the camera must be
re-calibrated ⇒ Communication; Rep. gr. 91 ; Overhead view
camera .
Tightening torques
♦ ⇒ “8.1 Exploded view - exterior mirror”, page 397
8.2.2 Removing and installing cover for exte‐

rior mirror
Removing
– Remove exterior mirror housing ⇒ page 400 .

– Press retainer -5- to the side slightly and pull electrical con‐
nector -4- out of mounting.
– On vehicles with overhead view camera system, unplug elec‐
trical connector.
– Release retaining tabs -1-.
– Detach cover -2- from mounting for mirror adjustment unit
-3- in direction of -arrow-.
Installing
– On vehicles with overhead view camera, overhead view cam‐
era must be re-calibrated ⇒ Communication; Rep. gr. 91 ;
Overhead view camera; Overview of fitting locations - over‐
head view camera system .
8.3 Removing and installing mirror glass

♦ Suction lifter - V.A.G 1344-
♦ Protective gloves
Removing
WARNING
Risk of injury
♦ Put on protective gloves.
– Apply suction lifter - V.A.G 1344- centrally to mirror glass -1-,

– Pull mirror glass off mirror adjustment unit with suction lifter -
V.A.G 1344- .

– Unplug electrical connectors -1 and 2- for mirror glass heating

on rear of mirror glass -3-.
– If fitted, unclip electrical connector -4- from bracket -arrow- and
unplug.
Installing
– Position mirror glass at mirror adjustment unit and press mirror
glass on.
Note
Only exert pressure in the centre of the mirror when pressing on

the mirror glass.
8.4 Removing and installing mirror adjust‐

ment unit
Removing
– Remove mirror glass ⇒ page 399 .
– Disengage mirror adjustment unit -2- on outside of mounting
-arrow-.
– Unplug electrical connector -3- at mirror adjustment unit.
– Detach mirror adjustment unit.
Installing
– Press mirror adjustment unit onto mirror mounting until it en‐
gages audibly.
Tightening torques
8.5 Removing and installing cover for mirror

Removing
– Remove mirror glass ⇒ page 399 .

– Remove bolts -4- and -5-.

– Release retaining tabs -3- (4x).
– Pull exterior mirror housing -2- off cover -1- -arrows-.
– On vehicles with lane change assist, unplug electrical con‐
nector -6- for lane change assist warning lamp.
– Lift off exterior mirror housing and unplug electrical connector
for turn signal repeater bulb.
– If renewing housing, remove turn signal repeater bulb ⇒ Elec‐
trical system; Rep. gr. 94 ; Lights in exterior mirror; Removing
and installing turn signal repeater bulb -L131- / -L132- .
Installing
– Tighten bolts for securing housing to 2 Nm.
Tightening torques

9 Wheel housing liner

⇒ “9.1 Exploded view - wheel housing liner (front)”, page 402
⇒ “9.2 Exploded view - wheel housing liner (rear)”, page 405
⇒ “9.3 Removing and installing wheel housing liner (front)”, page
406
⇒ “9.4 Removing and installing wheel housing liner (rear)”,
page 410
9.1 Exploded view - wheel housing liner

(front)
⇒ “9.1.1 Exploded view - wheel housing liner”, page 402
⇒ “9.1.2 Exploded view - wheel spoiler”, page 403
⇒ “9.1.3 Exploded view - wheel spoiler, Audi RS 6”, page 404
9.1.1 Exploded view - wheel housing liner
1 - Drive shaft cover

⇒ page 407
2 - Nut
❑ 2x
❑ 2 Nm
3 - Cover for longitudinal mem‐
ber
logue
⇒ page 408
4 - Retaining clip
5 - Wheel housing liner (front)
logue
⇒ page 406
6 - Nut
❑ 2 Nm
7 - Nut
❑ 2 Nm
8 - Bolt
❑ 2.1 Nm
9 - Retainer
❑ For securing wheel
housing liner to wing
10 - Bolt
❑ 5x
❑ 2.1 Nm

11 - Nut
❑ For vehicles from model year 2015 onwards
❑ 2 Nm
12 - Retaining clip/nut
❑ 2x
❑ Nut: 2 Nm
13 - Spreader rivet
❑ 2x
9.1.2 Exploded view - wheel spoiler
❑ 2x
2 - Speed nut
❑ 2x
❑ For quick-release fas‐
tener
3 - Grommet
❑ For exhaust pipe for
auxiliary heater
❑ Depending on vehicle
equipment
4 - Wheel spoiler (front right)
⇒ page 409
5 - Clip
❑ 2x
6 - Spreader rivet
7 - Wheel spoiler (front left)
⇒ page 409
8 - Bolt
❑ 2 Nm
9 - Bolt
❑ 2 Nm
10 - Speed nut
9. Wheel housing liner 403

9.1.3 Exploded view - wheel spoiler, Audi RS 6
1 - Wheel spoiler (front)

⇒ page 409
2 - Bolt
❑ 2x
❑ 2.1 Nm
3 - Bolt
❑ 5x
❑ 2.1 Nm
4 - Spoiler lip
⇒ page 410
5 - Bolt
❑ 2x
❑ 2.1 Nm

9.2 Exploded view - wheel housing liner (rear)
1 - Retaining clip
❑ 9x
2 - Wheel housing liner (rear)
logue
⇒ page 410
3 - Bolt
❑ 3x
❑ 2 Nm

9.3 Removing and installing wheel housing

liner (front)
⇒ “9.3.1 Removing and installing wheel housing liner (front)”,
page 406
⇒ “9.3.2 Removing and installing wheel housing liner (front) - Audi
RS 6”, page 407
⇒ “9.3.3 Removing and installing drive shaft cover”, page 407
⇒ “9.3.4 Removing and installing cover for longitudinal member”,
page 408
⇒ “9.3.5 Removing and installing wheel spoiler (front)”,
page 409
⇒ “9.3.6 Removing and installing wheel spoiler (front) - Audi
RS 6”, page 409
⇒ “9.3.7 Removing and installing spoiler lip - Audi RS 6”,
page 410
9.3.1 Removing and installing wheel housing

liner (front)
Removing
– Remove drive shaft cover ⇒ page 407 .
– Unscrew nuts -3- and bolts -1-.
– Unscrew bolt -4- and disengage retainer -5- at wing panel.
– Detach retaining clips/nuts -7- from wheel housing liner -6-.

– You can also use locking pliers for Phaeton steering rack -
VAS 6199- to release clips.
– Take out wheel housing liner.
Installing
– After fitting, check that retaining clip is locked in position.
Tightening torques
♦ ⇒ “9.1.1 Exploded view - wheel housing liner”, page 402


liner (front) - Audi RS 6
Removing
– Remove spreader rivet -3-.
– Unscrew nuts -2- and bolts -1-.
– Unscrew bolt -4- and disengage bracket at wing.
– Detach retaining clips -6- from wheel housing liner -5-.

Installing
Tightening torques
9.3.3 Removing and installing drive shaft cov‐

er
Removing
– Turn front wheel all the way to the left.


– Left side of vehicle: Move electrical wiring -1- clear -arrow-.
– Turn front wheel all the way to the right.
– Pull drive shaft cover -4- off threaded pins and take out to‐
wards rear and downwards.
Installing
Tightening torques
9.3.4 Removing and installing cover for longi‐

tudinal member
Removing
– Remove front wheel housing liner ⇒ page 406 .
– Drill out rivets -4- and detach bracket -3- for brake hose.
– Lift cover -2- and take out towards front.
Installing
– Retaining clip -1- must be fitted on cover as shown in illustra‐
tion.
– Install bracket for brake hose ⇒ Brake system; Rep. gr. 46 ;
Front brakes; Exploded view - front brake .

9.3.5 Removing and installing wheel spoiler

(front)
Removing
– Release quick-release fastener -5- and detach wheel spoiler
-2-.
Installing
Tightening torques
♦ ⇒ “9.1.2 Exploded view - wheel spoiler”, page 403
9.3.6 Removing and installing wheel spoiler

(front) - Audi RS 6
Removing
– Release quick-release fastener -4- and detach wheel spoiler
-3-.
Installing
Tightening torques
♦ ⇒ “9.1.3 Exploded view - wheel spoiler, Audi RS 6”,
page 404

9.3.7 Removing and installing spoiler lip - Audi

RS 6
Removing
– Detach spoiler lip -1-.
Installing
Tightening torques
♦ ⇒ “9.1.3 Exploded view - wheel spoiler, Audi RS 6”,
page 404
9.4 Removing and installing wheel housing

liner (rear)
⇒ “9.4.1 Removing and installing wheel housing liner (rear)”, page
410
⇒ “9.4.2 Removing and installing wheel housing liner (rear) - Audi
RS 6”, page 411

liner (rear)
Removing
• Rear wheel removed ⇒ Running gear, axles, steering; Rep.
gr. 44 ; Wheels and tyres .


Installing
Tightening torques

liner (rear) - Audi RS 6
Removing
• Rear wheel removed ⇒ Running gear, axles, steering; Rep.
gr. 44 ; Wheels and tyres .
– Remove spreader rivet -3-.

Installing
Tightening torques

10 Model badges and brand emblems

⇒ “10.1 General notes”, page 412
⇒ “10.2 Dimensions - model badges and brand emblems on rear”,
page 412
⇒ “10.3 Dimensions - model badges and brand emblems on side”,
page 416
⇒ “10.4 Removing and installing front emblem”, page 416
⇒ “10.5 Removing and installing emblems”, page 418
10.1 General notes

♦ Roller - 3356-
Caution
♦ Any model badges and brand emblems that are removed

must be renewed.
♦ The vehicle must be at room temperature before bonding
on model badges and brand emblems.
♦ The bonding surfaces on the body must be free of dust,
grease and adhesive residue.
♦ Clean bonding surfaces with cleaning solution - D 009 401
04- .
♦ Heat bonding surfaces with a hot air blower to approx. 40 °
C.
♦ Adjacent components must be protected against high
temperatures.
♦ After installing, press on emblems with roller.
10.2 Dimensions - model badges and brand

emblems on rear
⇒ “10.2.1 Dimensions - model badges and brand emblems on rear
lid, Saloon”, page 412
lid, Saloon (country-specific version)”, page 414
lid, Avant”, page 415
10.2.1 Dimensions - model badges and brand emblems on rear lid, Saloon

♦ Dimension -a- = 61 mm
10. Model badges and brand emblems 413

10.2.2 Dimensions - model badges and brand emblems on rear lid, Saloon (coun‐
try-specific version)
♦ Dimension -b- = 48.5 mm
♦ Dimension -e- = 4mm

10.2.3 Dimensions - model badges and brand emblems on rear lid, Avant
Note
The allroad emblem is located on the right side of the vehicle.

10.3 Dimensions - model badges and brand emblems on side
1 - Model/brand emblem
❑ V8T
❑ hybrid
❑ e-tron
❑ SUPERCHARGED
(left-side)
❑ SUPERCHARGED
(right-side)
❑ S line
2 - Reference edge on wing
panel
3 - Rear edge of wing panel
10.4 Removing and installing front emblem

⇒ “10.4.1 Removing and installing front emblem - Audi A6/allroad/
S6”, page 416
⇒ “10.4.2 Removing and installing front emblem - Audi RS 6”,
page 417
10.4.1 Removing and installing front emblem -

Audi A6/allroad/S6
Removing
– If fitted, remove overhead view camera ⇒ Communication;
Rep. gr. 91 ; Overhead view camera; Overview of fitting lo‐
cations - overhead view camera .

– Release retaining tabs -arrow- and detach cover -1-.
– Lift securing tab -4- in direction of -arrow- and release retaining

catch -3-.
– Detach Audi rings -1- from radiator grille -2-.
Installing
– Press Audi rings on until they engage audibly.
10.4.2 Removing and installing front emblem -

Audi RS 6
Removing
– Release retaining tab -1- -arrows- and detach cover -2-.
– Detach Audi rings from radiator grille using adapter.

– Lift securing tab -3- in direction of -arrow- and release retaining

catch -4-.
– Detach Audi rings -1- from adapter -2-.
Installing
– Press Audi rings on until they engage audibly.
10.5 Removing and installing emblems

⇒ “10.5.1 Removing and installing quattro emblem - vehicles up
to model year 2014”, page 418
⇒ “10.5.2 Removing and installing quattro emblem - vehicles from
⇒ “10.5.3 Removing and installing RS 6 emblem”, page 419
10.5.1 Removing and installing quattro emblem

- vehicles up to model year 2014
Removing
– Pull off retaining clips -arrows-.
– Take quattro emblem -2- out of radiator grille -1-.
Installing
– Position quattro emblem on radiator grille and press on re‐
taining clips until they engage audibly.
10.5.2 Removing and installing quattro emblem

- vehicles from model year 2015 on‐
wards
Removing

– Release fasteners -3- and detach retaining strip -2-.

– Remove quattro emblem -1- from radiator grille.
Installing
– Position quattro emblem on radiator grille and press on re‐
taining strip as far as stop.
10.5.3 Removing and installing RS 6 emblem

Removing
– Release fasteners -arrows- and detach retaining strip -3-.
– Take RS 6 emblem -2- out of radiator grille -1-.
Installing
– Position RS 6 emblem on radiator grille and press on retaining
strip as far as it will go.
• The retaining strip can only be pressed on in one position.

11 Towing bracket
⇒ “11.1 Exploded view - towing bracket”, page 420
⇒ “11.2 Removing and installing cable mounting bracket”,
page 421
⇒ “11.3 Removing and installing retainer for cable mounting
⇒ “11.4 Removing and installing towing bracket ”, page 423
11.1 Exploded view - towing bracket
1 - Grommet
❑ For cable
2 - Bolt
❑ 4x
❑ Impact bar
⇒ Item 11 (page 421) is
secured from inside;
see exploded view
⇒ page 260
⇒ page 260
3 - Cable
❑ For releasing towing
bracket
4 - Bolt
❑ 2 Nm
5 - Retainer
❑ For cable mounting
bracket
⇒ page 422
❑ For cable
⇒ page 270
7 - Pull knob
❑ For releasing towing
bracket
⇒ “2.5 Removing and in‐
stalling cable mounting
8 - Locking clip
❑ For pull knob
9 - Bolt
❑ Left side: 2x; right side: 4x
❑ Tightening torque ⇒ page 260
10 - Impact bar
❑ For vehicles without towing bracket

11 - Impact bar
❑ For vehicles with towing bracket
12 - Socket
❑ Removing and installing ⇒ Electrical system; Rep. gr. 96 ; Towing bracket; Trailer socket
❑ Pin assignment ⇒ Electrical system; Rep. gr. 96 ; Towing bracket; Trailer socket
13 - Bolt
❑ 3x
❑ 3.5 Nm
11.2 Removing and installing cable mounting

bracket
WARNING

Removing
– Remove cover for luggage compartment side trim (left-side)
⇒ General body repairs, interior; Rep. gr. 70 ; Luggage com‐
partment trim panels; Exploded view - luggage compartment
side trim .
– Pull out knob -3- at mounting bracket -1- and prise off locking
clip -4- using a small screwdriver -arrow-.
– Remove cable -2- from pull knob.
11. Towing bracket 421

– Pull cable mounting bracket -2- with cable support bracket

-1- downwards off retainer -3- -arrow-.
– Unplug electrical connector.

– Press cable support bracket -1- out of mounting bracket -2-
-arrow-.
Installing
– Install luggage compartment side trim ⇒ General body repairs,
interior; Rep. gr. 70 ; Luggage compartment trim panels; Ex‐
ploded view - luggage compartment side trim .
11.3 Removing and installing retainer for ca‐

ble mounting bracket
Removing
– Pull cable mounting bracket -2- with cable support bracket
-1- downwards off retainer -3- -arrow-.

– Unscrew bolt -3- and detach bracket -2-.

Installing
• Tightening torque
⇒ “2.2.1 Exploded view - impact bar, Audi A6/allroad/S6”, page
260
– Tab -1- on retainer must engage in recess in body.
– Install cable mounting bracket ⇒ page 270 .
11.4 Removing and installing towing bracket
1 - Towing bracket
❑ Removing
– Remove bumper cover
(rear) ⇒ page 264 .
– Pull control unit in right

side panel out of retain‐
ing frame and unplug
electrical connector.
– Release cable retain‐

ers, move wiring har‐
ness clear and push
grommet -4- through to
outside.
– Disengage cable from

retainer ⇒ page 270 and
take out of vehicle.
– Unscrew bolts -3-.
– Pull out impact bar -3-

together with a second
person.
2 - Cable
– Remove cable from
mounting bracket
⇒ page 270 .
3 - Bolt
❑ 75 Nm
4 - Electrical wire
5 - Grommet
sure sealing piece is
seated correctly.
6 - Longitudinal member
11. Towing bracket 423

General Body Repairs, Exterior PDF

Uploaded by

Copyright:

Available Formats

General Body Repairs, Exterior PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

General Body Repairs, Exterior PDF

Uploaded by

Copyright:

Available Formats

Service

Service Department. Technical Information

All rights reserved.

Copyright © 2019 Audi AG, Ingolstadt D3E80352453

55 - Bonnet, rear lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.12 Removing and installing rear lid lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

57 - Front doors, door components, central locking . . . . . . . . . . . . . . . . . . . . . . . . . . 92

58 - Rear doors, door components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

1.8 Removing and installing outer door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

1.2 Repairing windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

66 - Exterior equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319

5.5 Removing and installing diagonal struts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391

1.1 Safety precautions when working on the high-voltage system

Risk of injury - engine may start unexpectedly

Risk of damage to high-voltage wiring

1.2 Safety precautions when working in the vicinity of high-voltage components

1.3 Safety precautions when working on vehicles with start/stop system

1.5 Safety precautions when working on the cooling system

2 Rep. gr.00 - Technical data

2.1 Routing and attachment of lines and wir‐

2.2 Contact corrosion

2.3 Bonding surfaces for adhesive strips

2.4 Self-locking bolts

4 Rep. gr.00 - Technical data

1.1 Exploded view - lock carrier

1.1.1 Exploded view - lock carrier, vehicles up to model year 2014

6 Rep. gr.50 - Body - front

1.2 Removing and installing lock carrier

1.2.1 Removing and installing lock carrier -

– If fitted, unplug electrical connector -4- for secondary air pump

– If fitted, unscrew bolt -5-.

– Align bumper cover mounting (front) -2-, hold in position and

1.2.2 Removing and installing lock carrier -

8 Rep. gr.50 - Body - front

– Remove bolt -4-.

– Remove bolt -6-.

-Item 5- not installed.

– Align bumper cover mounting (front) -2-, hold in position and

1.2.3 Removing and installing lock carrier

1.2.4 Removing and installing bumper cover

1.2.5 Removing and installing bumper cover

10 Rep. gr.50 - Body - front

– Right-side: Remove air cleaner housing ⇒ Rep. gr. 23 ; Air

– Remove bolts -1, 3, 4-.

1.2.6 Removing and installing retainer for

– Release retaining tabs -arrows A- and detach air duct -1-

– Remove bolt -1-.

12 Rep. gr.50 - Body - front

2.1 Exploded view - wing

2.2 Removing and installing wing

2.2.1 Removing and installing wing

– Remove bolts -2 ... 5-.

14 Rep. gr.50 - Body - front

– Sealing piece -2- must be positioned between wing mounting

2.2.2 Removing and installing closure plate

– Remove spreader rivets -4-.

2.2.3 Removing and installing wing bracket

16 Rep. gr.50 - Body - front

3.1 Exploded view - plenum chamber partition panel